Operating Guide
Compact Programmable
Room Air Conditioner with remote control
CP14
CP18
CP24
Please register
your air conditioner
Whenever you call to request service
on your appliance, you will need to
provide your complete model number
and serial number. You can find this
information on the model and serial
number label.
Please record model and serial
number information below:
MODEL NUMBER
SERIAL NUMBER
PURCHASE DATE
66121417 (1-07)
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electrical shock or injury when using your air conditioner, follow these basic precautions:
■ Plug into a grounded 3 prong outlet.
■ Do not remove plug ground prong.
■ Do not use a plug adapter.
■ Do not use an extension cord.
■ Unplug air conditioner before servicing.
■ Use two or more people to move and install air conditioner.
SAVE THESE INSTRUCTIONS
Installation Requirements
Location Requirements
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
IMPORTANT: Observe all governing codes and ordinances.
Check the location where air conditioner will be installed.
Proper installation is your responsibility. Make sure you have
everything necessary for correct installation.
Tools Needed
The location should provide:
■ Flat-blade and Phillips
■ Tape measure
screwdrivers
■ Grounded electrical outlet within 4 ft (122 cm) of where the
power cord exits the air conditioner.
■ Drill and ³⁄16" or smaller bit
■ Level
NOTE: Do not use an extensioncord.
Through-the-wall installation
In addition to the tools listed above, the following tools and sup-
plies are needed for though-the-wall installation.
■ Free movement of air in room to be cooled.
■ A large enough opening for the air conditioner.
■ Adequate wall support for weight of air conditioner. Air con-
■ Saw
■ 1" (2.5 cm) or thicker lumber
■ 7 - #10 x 1" wood screws
ditioner weighs between 145 and 200 lbs (66 to 91kg).
■ Wood preservative
■ Caulk
NOTE: Cabinet louvers must not be obstructed. Air must be
able to pass freely through the cabinet louvers (A).
Parts supplied (on some models)
Check that all parts are included in parts package.
A
A
C
B
J
H
G
F
D E
A. Cabinet louvers
I
A. Support brackets with
adjustment bolts (2)
F. #10 x ¹⁄₂" pan-head Phillips
screws (4)
B. Foam seals (2)
G. #10 x ³⁄₄" round-head screws (6)
C. Window lock bracket (2)
D. #10 x ¹⁄₄" pan-head Phillips
screws (6)
H. #10 x ⁷⁄₈" pan-head Phillips
screws (4)
I. Top channel
E. #10 x ³⁄₈" washer-head
Phillips screws (4)
J. Side curtains (2)
NOTE: Installation parts are supplied for double-hung windows
up to 40" (101.6 cm) wide. A special Wide Window Kit is available
from your dealer or service center. See “Accessories.”
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Window installation
Electrical Requirements
Window opening measurements:
27"min. to 42" max. (76.2 cm to 101.6 cm) opening width (A).
WARNING
20" min. (50.8 cm) opening height (B).
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove powercord ground prong.
Do not use a plug adapter.
A
B
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
A.27" min. (76.2 cm)
B . 20" min. (50.8 cm)
Ground wire must be connected to ground screw located in lower
right corner of air conditioner when air conditioner is in cabinet.
The electrical ratings for your air conditioner are listed on the
model and serial number (nameplate) label. The model and serial
number label is located behind the front panel on the flange below
the control panel area.
Through-the-wall installation
The wall opening measurements should be:
ꢀ
Height (A): 17 ¼" plus twice thickness of wood used to build
frame
Specific electrical requirements are listed in the chart below.
Follow the requirements for the type of plug on the power supply
cord.
ꢀ
ꢀ
Width (B): 26 ¼"
Depth (D): 4" minimum to 8" maximum.
Power supply
cord
Wiring requirements
CP14
■
■
■
■
115-volt (103.5 min. - 126.5 max.)
0-12 amps
C
A
15-amp time-delay fuse or circuit breaker
Use on single outlet circuit only.
B
D
CP18 / CP24
¹⁄₄"
■
■
■
■
230-volt (207 min. - 253 max.)
0-12 amps
(0.6 cm)
C
15-amp time-delay fuse or circuit breaker
Use on single outlet circuit only.
A. 17 ¼"
B. 26 ¼"
C. Wood thickness
D. 4" minimum to
8" maximum.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Recommended grounding method
WARNING
This air conditioner must be grounded. This air conditioner is
equipped with a power supply cord having a grounded 3 prong
plug. To minimize possible shock hazard, the cord must be
plugged into a mating, grounded 3 prong outlet, grounded in
accordance with all local codes and ordinances. If a mating outlet
is not available, it is the customer's responsibility to have a
properly grounded 3 prong outlet installed by a qualified electrical
component installer.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove powercord ground prong.
Do not use a plug adapter.
It is the customer's responsibility:
To contact a qualified electrical installer, and
To assure that the electrical installation is adequate and in
conformance with National Electrical Code, ANSI/NFPA 70 -
latest edition, and all local codes and ordinances.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Copies of the standards listed may be obtained from:
National Fire Protection Association
One Batterymarch Park
Quincy, MA 02269
To test your power supply cord:
1. Plug power supply cord into a grounded 3 prong outlet.
2. Press RESET.
Power Supply Cord
3. Press TEST (listen for click; Reset button will trip and pop
out).
NOTE: Your unit’s device may differ from the ones shown.
B
A
4. Press and release RESET (listen for click; Reset button will
latch and remain in). The power supply cord is ready for
operation.
NOTES:
The Reset button must be pushed in for proper operation.
The power supply cord must be replaced if it fails to trip when
the test button is pressed or if it fails to reset.
Do not use the power supply cord as an off/on switch. The
power supply cord is designed as a protective device.
A damaged power supply cord must be replaced with a new
power supply cord obtained from the product manufacturer
and must not be repaired.
The power supply cord contains no user serviceable parts.
Opening the tamper-resistant case voids all warranty and
performance claims.
A
B
A. Reset button
B. Test button
This room air conditioner is equipped with a power supply cord
required by UL. This power supply cord contains state-of-the-art
electronics that sense leakage current. If the cord is crushed, the
electronics detect leakage current and power will be
disconnected in a fraction of a second.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
Unpacking
5.
Remove the window lock bracket and screw from the air
6. Remove front panel screw from right side of filter
conditioner and set aside.
area.
WARNING
Excessive Weight Hazard
Use two or more people to move and install
air conditioner.
Failure to do so can result in back or other injury.
Remove packaging materials
ꢀ Remove and dispose of or recycle packaging materials. Remove
tape and glue residue from surfaces before turning on the air
conditioner. Rub a small amound of liquid dish soap over the
adhesive with your fingers. Wipe with warm water and dry.
ꢀ Do not use sharp instruments, rubbing alcohol, flammable fluids,
or abrasive cleaners to remove tape or glue. These products can
damage the surface of your air conditioner.
ꢀ Handle air conditioner carefully and gently
1. Remove the air conditioner from the carton and place it on
7. Remove the ground screw and ground wire from
the front of the air conditioner. Save the ground
screw.
cardboard.
2. Remove shipping screws from the rear of the cabinet (if present).
B
A
A. Green ground wire
B. Ground screw
A
8. Pull on handle to slide air conditioner out of
cabinet. Place air conditioner on cardboard.
A. Remove shipping screws
3. Remove front grille by pulling bottom of grille upward.
Remove hinges at top.
4. Remove air filter
5. Remove the window lock bracket and screw from the air
conditioner and set aside.
A
A. Pull Handle
NOTE: Do not lift, push, pull or remove any expanded
polystyrene (foam) from inside the air conditioner. It is
not packing material.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Window Installation (on some models)
NOTES:
Bottom view
■
Handle air conditioner carefully and gently.
■
Be sure your air conditioner cabinet does not fall out of the
opening during installation or removal.
■
The place where the power cord exits the air conditioner
should be no more than 4 ft (122 cm) from a grounded
3 prong power outlet.
A
■
■
Do not block the louvers on the front panel.
B
Do not block the louvers on the outside of the air conditioner.
A. Curtain housing
B. Curtain bottom channel on air conditioner
Attach Top Channel
3. Extend right-hand curtain outward so you may insert the
first screw through the middle hole of the curtain. Using #10 x
¹⁄₄" pan-head Phillips screw, screw curtain to middle hole in
air conditioner cabinet.
NOTE: Attach top channel and side curtains to air conditioner
cabinet before placing cabinet in window.
1. Locate provided bag of screws.
NOTE: This screw is required to correctly attach curtain (top
to bottom) to the air conditioner cabinet.
2. Place top channel on top of air conditioner cabinet, lining up
the 4 holes in top channel with the 4 holes on top of air
conditioner cabinet.
3. Using 4 - #10 x ³⁄₈" washer-head Phillips thread-cutting
screws, attach top channel to air conditioner cabinet.
A
B
4. While the right-hand curtain is still extended, insert #10 x ¹⁄₄"
pan-head Phillips screws into the top and bottom slots of
curtain. Screw curtain to the top and bottom holes in the air
conditioner cabinet side.
A. Top channel
B. #10 x ³⁄₈" washer-head Phillips thread-cutting screws
5. Slide the curtain housing into the curtain channels as far as it
will go.
6. Repeat above steps for the left-hand curtain.
Attach Side Curtains
Attach foam adhesive seal
1. Locate provided bag of screws.
2. Insert top and then bottom of right-hand curtain housing in
Attach foam adhesive seal along the bottom of the curtain
bottom channel.
top and bottom curtain channels on air conditioner.
Top view
A
B
A
B
A. Curtain housing
B. Foam adhesive seal
A. Curtain housing
B. Curtain top channel on air conditioner
7
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Install Cabinet into Window
Attach Side Curtains to Window Frame
■
■
Handle air conditioner carefully and gently.
1. Pull left-hand curtain out until it fits into window channel. Use
a ³⁄₃₂" drill bit to drill a starter hole through the hole in the
curtain housing and into the lower window sash.
Be sure your air conditioner cabinet does not fall out of the
opening during installation or removal.
■
The place where the power cord exits the air conditioner
should be no more than 4 ft (122 cm) from a grounded
3 prong power outlet.
Front View
■
■
Do not place cabinet where front louvers will be blocked.
Do not place cabinet where outside louvers will be blocked.
1. Center empty cabinet in window. Check that lower rail of air
conditioner cabinet is behind and against back side of
windowsill. Maintain a firm hold on the air conditioner
cabinet. Lower window sash to hold cabinet in place.
2. Measure the distance between the right-hand side of the
cabinet and the inside of the window channel.
3. Repeat for the left side. Adjust the cabinet until the distance
on each side is the same.
Top View
B
A
B
A
C
C
A. Left-hand curtain
D
B. Window channel
C. #10 x ³⁄₄" round-head screw
A. Window sash
B. Empty cabinet
C. Window channel
2. Insert one of the #10 x ³⁄₄" round-head screws through the
threaded hole in the top of the curtain.
D. Window Seal
4. Use a ³⁄₁₆" drill bit to drill 4 starter holes ³⁄₈" deep through the 4
holes in the cabinet and into the windowsill.
A
5. Attach cabinet to windowsill with 4 - #10 x ¹⁄₂" pan-head
Phillips screws.
4. Use a ³⁄₁₆" drill bit to drill 4 starter holes ³⁄₈" deep through the 4
holes in the cabinet and into the windowsill.
5. Attach cabinet to windowsill with 4 - #10 x ¹⁄₂" pan-head
Phillips screws.
A. #10 x ³⁄₄" round-head screw
3. Repeat for right-hand curtain.
Attach Support Brackets
B
A
A
A
B
A. #10 x ⁄₂" pan-head Phillips screws
B. Windowsill
6. Check that air conditioner cabinet is tilted to the outside so
A. Align holes in cabinet with holes in support bracket.
B. #10 x 7/8" 1
that water will run to the outside.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Using #10 x ⁷⁄₈" pan-head Phillips screws, attach bracket to
Complete Installation
cabinet. Repeat for other bracket.
3. Loosen locking nut and turn the adjustment bolt (C) for each
1. Insert seal behind the top of the lower window sash and
bracket until the bolt touches the wall (B).
against the glass of the upper window (B).
4. Tighten the locking nut on adjustment bolt to lock in position.
2. Place one window-lock bracket on top of lower window and
against upper window sash on each side of window (A).
3. Use a ³⁄₃₂" drill bit to drill a starter holes through the holes in
each bracket into the window sash.
4. Attach both window-lock brackets to window sash with #10 x
³⁄₄" round-head screws to secure window in place.
C
B
A
A
B
C
A
A. Support bracket
B. Locking nut
C. Adjustment bolt
A. Window lock brackets
B. Window rail seal
C. Upper window glass
Through-the-Wall Cabinet Installation
NOTES:
Option 2—Plastered wall with no molding
If the plastered wall is to be flush with the cabinet and no molding
is used, the wood frame must be set ¹⁄₂" (13 mm) into the inside
wall.
■
Handle air conditioner gently.
■
Be sure your air conditioner cabinet does not fall out of the
opening during installation or removal.
A B
C
■
■
The place where the power cord exits the air conditioner
should be no more than 4 ft (122 cm) from a grounded
3 prong outlet.
D
It is the customer's responsibility and obligation to have this
product installed by a qualified technician familiar with
through-the-wall room air conditioner installations.
■
■
Do not block the louvers on the front panel.
Do not block the louvers on the outside of the air conditioner.
Option 1—Wood, metal or plastic molding
When using a wood, metal or plastic molding, the wood frame
should line up with inside wall as shown.
A. Plastered wall
B. Inside wall
C. Wood frame
D. Louvers
A B C
Install Wood Frame
1. Construct wood frame. See “Location Requirements” for
D
dimensions.
2. Measure outside width and height of frame to determine wall
opening dimensions.
3. Cut opening through the wall. Remove and save insulation.
NOTES:
■
■
Dimension for depth depends on wall thickness and type
of molding.
A. Trim Molding
B. Inside wall
surface
C. Wood wall framing
D. Louvers
Do not block louvers in air conditioner cabinet.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
■
Use 2" x 4" or thicker lumber for wood frame.
A
2. Insert cabinet into the framed wall opening. The top of the
cabinet should extend ³⁄₄" (19.1 mm) into the room. If there is
trim, the cabinet should extend ³⁄₄" (19.1 mm) past the trim.
B
A
B
C
A. Outside width
B. Outside height
C. Depth
4. Apply wood preservative to the outside exposed surface.
5. Insert the frame in the wall opening. Square and level frame.
6. Attach frame securely to the wall.
A. ³⁄₄ " (19.1 mm) extending into room
B. Trim
3. Use a level to check that cabinet is level side to side.
Install Cabinet into Wood Frame
1. Remove top channel and both side channels using a ¹⁄₄" nut
driver or socket wrench. Discard top channel and both side
channels.
A
A
A. Level
A
4. Check that air conditioner cabinet is tilted to the outside so
that water will run to the outside.
5. Reuse the insulation to seal opening between cabinet and
A
frame.
6. Use existing holes in sides and top of cabinet and 7 - #10 x
1" wood screws (not provided) to attach cabinet to frame.
NOTE: Do not overtighten screws or cabinet will distort and
provide a poor air seal between cabinet and air conditioner.
7. Caulk all outside wall openings around cabinet.
A. Remove these screws
Complete Installation
NOTE: Handle air conditioner carefully and gently.
2. Insert air conditioner into cabinet.
1. Make sure the free end of the ground wire is outside of the
cabinet.
WARNING
Excessive Weight Hazard
Use two or more people to move and install
air conditioner.
Failure to do so can result in back or other injury.
A
A
A. Make sure the free end of the ground wire is outside of the cabinet.
A. Make sure the free end of the ground wire is outside of the cabinet.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
3
5. Using 2 - #10 x ³⁄₈" r8ound-head screws, attach bottom front of
5. Using 1 - #10 x / " round-head screw, attach front of panel
panel to chassis.
to chassis.
WARNING
Electrical Shock Hazard
Connect green ground wire to ground screw.
Failure to do so can result in death or electrical shock.
3. Connect green ground wire to cabinet base with ground
screw.
Position ground wire pointing straight up. Put excess ground
wire between coil and air conditioner cabinet.
6. Reinstall filter and replace front grille.
NOTE: For through-the-wall installations, if needed, install
molding around room side of cabinet.
A
WARNING
B
B
A
A. Green ground wire
B. Ground screw
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
4. Push front panel straight on and then lower it slightly to lock it
into place.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
7. Plug into a grounded 3 prong outlet.
8. Press RESET on the power supply cord.
Air Conditioner Use
Operating your air conditioner properly helps you to obtain the
best possible results.
■
Do not try to operate your air conditioner in the cooling mode
when outside temperature is below 65°F (18°C). The inside
evaporator coil will freeze up, and the air conditioner will not
operate properly.
This section explains proper air conditioner operation.
IMPORTANT:
NOTE: In the event of a power failure, your air conditioner will
operate at the previous settings when the power is restored.
■
If you turn off the air conditioner, wait at least 3 minutes
before turning it back on. This prevents the air conditioner
from blowing a fuse or tripping a circuit breaker.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Starting Your Air Conditioner—Digital Control
Temperature
Press, or press and hold, the plus button to raise the
temperature 1º until it reaches 86ºF (30ºC).
Money
Saver®
AutoSwing
Timer
0F
0F
Temp/Hour
Temp/Hour
Hr.
Hr.
POWER
Cool
High
Med
Low
Mode
Fan Speed
Fan Only
Press, or press and hold, the minus button to lower the
temperature 1º until it reaches 64ºF (18ºC).
1. Press POWER to turn on air conditioner.
Timer Delay
To set the Timer for a 1- to 24-hour delay until the air
conditioner turns off (the air conditioner must be On):
1. Press TIMER. Indicator light will flash.
POWER
NOTE: When the unit is turned on, it will display the previous
settings for the Mode, Fan Speed and temperature.
Timer
2. Choose mode. See “Mode.”
3. Choose fan speed. See “Fan Speed.”
4. Choose temperature. See “Temperature.”
2. Press the plus or minus button to change the delay time from
1 to 24 hours.
3. Press TIMER or wait 10 seconds. Indicator light will remain
on.
Mode
1. Press and hold MODE.
To set the Timer delay for a 1- to 24-hour delay until the air
conditioner turns on, keeping previous settings:
1. Turn off air conditioner.
2.
Choose Cool or Fan mode
Cool—Cools room. Press FAN SPEED to choose fan
speed. Then adjust the temperature by pressing the up or
down arrow buttons.
2. Press TIMER. Indicator light will flash.
3. Press the plus or minus button to change the delay time from
1 to 24 hours.
Fan—Operates the fan at High speed, without cooling.
The display shows “FO” (fanonly).
4. Press TIMER or wait 10 seconds. Indicator light will remain
on.
Money Saver®
To set the Timer delay for a 1- to 24-hour delay until the air
conditioner turns on, changing previous settings:
1. Turn on air conditioner.
Money Saver — Turns fan to low speed when
room temperature reaches the temperature setting
on the thermostat.
2. Adjust MODE to desired setting.
3. Adjust FAN SPEEDto High, Medium or Low.
4. Adjust temperature between 64ºF (18ºC) and 86ºF (30ºC).
5. Turn off air conditioner.
Cool
Money
Saver®
Mode
Fan Only
6. Press TIMER. Indicator light will flash.
7. Press the plus or minus button to change delay time from 1 to
24 hours.
Fan Speed
8. Press TIMER or wait 10 seconds.
NOTE: The FanSpeed button will operate only when the Cool or
Power Saver mode has been selected.
To clear Timer delay program
NOTE: Air conditioner can be either on or off.
1. Press and hold FAN SPEED until you see the indicator light
for the desired setting.
Press and hold TIMER for 3 seconds. Indicator light will turn off.
2. Choose High, Medium or Low.
To see the time remaining (in hours)
High
1. Press TIMER once after it has been set.
Med
Fan Speed
2. While the display is showing the remaining time, you can
press the plus or minus button to increase or decrease the
time.
Low
12
Download from Www.Somanuals.com. All Manuals Search And Download.
To raise the temperature:
To operate air conditioner with remote control
Press the plus button to raise the temperature. Each time you
press or hold the plus button, the temperature will go up 1º until it
reaches 86°F (30°C).
NOTE: Remote control may vary in appearance.
To lower the temperature:
Press the minus button to lower the temperature. Each time you
press or hold the minus button, the temperature will go down 1º
until it reaches 64°F (18°C).
To set Timer for a 1- to 24-hour delay before air conditioner
is turned off (air conditioner must be On):
1. Press TIMER. Indicator light on air conditioner control panel
will flash.
2. Press the plus or minus button to change the delay time from
1 to 24 hours.
3. Press TIMER again or wait 10 seconds. Indicator light on air
conditioner control panel will remain on.
NOTE: Two AAA batteries (included) power the remote control.
Replace batteries after 6 months of use, or when the remote
control starts to lose power.
To set Timer to turn on air conditioner, keeping previous
settings:
1. Turn off air conditioner.
To turn the air conditioner on or off:
Press POWER.
2. Press TIMER. Indicator light on air conditioner control panel
will flash.
3. Press the plus or minus button to change delay time (1 to
24 hours).
4. Press TIMER again or wait 10 seconds. Indicator light on air
conditioner control panel will remain on.
To select the mode:
Press COOL, FAN or $ SAVER
To set Timer to turn on air conditioner, changing the
previous settings:
1. Turn on air conditioner.
2. Adjust Mode to Cool, Fan Only, or Power Saver.
3. Adjust Fan Speed to High, Medium or Low.
4. Adjust temperature between 64°F (18ºC) and 86°F (30ºC).
5. Turn off air conditioner.
To select the fan speed:
Press FAN SPEED for High, Medium or Low.
6. Press TIMER. Indicator light on air conditioner control panel
will flash.
7. Press the plus or minus button to change delay time (1 to
24 hours).
8. Press TIMER again or wait 10 seconds. Indicator light on air
conditioner control panel will remain on.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Air Conditioner Care
Your new air conditioner is designed to give you many years of
dependable service. This section tells you how to clean and care
for your air conditioner properly. Call your local authorized dealer
for an annual checkup. Remember… the cost of this service call
is your responsibility.
Cleaning the Front Panel
1. Turn off air conditioner.
2. Remove the air filter and clean it separately. See “Cleaning
the Air Filter.”
3. Wipe the front panel with a soft, damp cloth.
4. Air dry front panel completely.
Cleaning the Air Filter
The air filter is removable for easy cleaning. A clean filter helps
remove dust, lint, and other particles from the air and is important
for best cooling and operating efficiency. Check the filter every
2 weeks to see whether it needs cleaning.
Repairing Paint Damage
Check once or twice a year for paint damage. This is very
important, especially in areas near oceans or where rust is a
problem. If needed, touch up with a good grade enamel paint.
NOTE: Do not operate the air conditioner without the filter in
place.
1. Turn off air conditioner.
2. Remove filter from unit.
Annual Maintenance
3. Use a vacuum cleaner to clean air filter. If air filter is very dirty,
wash it in warm water with a mild detergent. Do not wash air
filter in the dishwasher or use any chemical cleaners. Air dry
filter completely before replacing to ensure maximum
efficiency.
Your air conditioner needs annual maintenance to help ensure
steady, top performance throughout the year. Call your local
authorized dealer to schedule an annual checkup. The expense
of an annual inspection is your responsibility.
4. Slide air filter down into the filter door. Close filter door.
Troubleshooting
Before calling for service, try the suggestions below to see whether you can solve your problem without outside help.
Air conditioner will not operate
Air conditioner blows fuses or trips circuit breakers
Too many appliances are being used on the same circuit.
WARNING
Unplug or relocate appliances that share the same circuit.
Time-delay fuse or circuit breaker of the wrong capacity
is being used. Replace with a time-delay fuse or circuit
breaker of the correct capacity. See “Electrical
Requirements.”
An extension cord is being used. Do not use an extension
cord with this or any other appliance.
Electrical Shock Hazard
You are trying to restart the air conditioner too soon after
turning the unit off. Wait at least 3 minutes after turning the
unit off before trying to restart the air conditioner.
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Normal Sounds
Failure to follow these instructions can result in death,
fire, or electrical shock.
When your air conditioner is operating normally, you may hear
sounds such as:
Droplets of water hitting the condenser, causing a pinging or
clicking sound. The water droplets help cool the condenser.
The power supply cord is unplugged. Plug into a grounded
3 prong outlet. See “Electrical Requirements.”
Air movement from the fan.
The power supply cord has tripped (Reset button has
popped out). Press and release RESET (listen for click; Reset
button will latch and remain in) to resume operation.
Clicks from the thermostat cycle.
Vibrations or noise due to poor wall or window construction.
A household fuse has blown, or a circuit breaker has
tripped. Replace the fuse or reset the circuit breaker. If the
problem continues, call an electrician. See “Electrical
Requirements.”
A high-pitched hum or pulsating noise caused by the modern
high-efficiency compressor cycling on and off.
Depending on model, the Power button has not been
pressed or the Fan control is turned to Off. Press POWER
or turn the Fan control to an active setting.
The local power has failed. Wait for power to be restored.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
■
There is excessive heat or moisture (open container
cooking, showers, etc.) in the room. Use a fan to exhaust
heat or moisture from the room. Try not to use heat-
producing appliances during the hottest part of the day.
Air conditioner power supply cord trips (Reset button
pops out)
■
■
Disturbances in your electrical current can trip (Reset
button will pop out) the power supply cord. Press and
release RESET (listen for click; Reset button will latch and
remain in) to resume operation.
■
■
■
The louvers are blocked. Install the air conditioner in a
location where the louvers are free from curtains, blinds,
furniture, etc.
The outside temperature is below 65°F (18°C). Do not try to
operate your air conditioner in the cooling mode when the
outside temperature is below 65°F (18°C).
Electrical overloading, overheating, cord pinching or
aging can trip (Reset button will pop out) the power
supply cord. After correcting the problem, press and release
RESET (listen for click; Reset button will latch and remain in)
to resume operation.
The temperature of the room you are trying to cool is
extremely hot. Allow extra time for the air conditioner to cool
off a very hot room.
NOTE: A damaged power supply cord must be replaced with a
new power supply cord obtained from the product manufacturer
and must not be repaired.
■
■
Windows or doors to the outside are open. Close all
windows and doors.
The Vent control is set to OPEN (on some models). Push
the Vent control to CLOSED for maximum cooling and/or
heating.
Air conditioner seems to run too much
■
The current air conditioner replaced an older model. The
use of more efficient components may cause the air
■
The temperature set point or Thermostat control is not at
a cool enough setting. Adjust the temperature set point to a
cooler setting by pressing the minus button to reduce the
temperature or adjust the Thermostat control to a cooler
setting by turning the knob clockwise. Turn the Fan control to
Turbo Cool.
conditioner to run longer than an older model, but the total
energy consumption will be less. Newer air conditioners do
not emit the “blast” of cold air you may be accustomed to
from older units, but this is not an indication of lesser cooling
capacity or efficiency. Refer to the efficiency rating (EER) and
capacity rating (in BTU/hr.) marked on the air conditioner.
■
The air contitioner in the heating mode has insufficient
BTU/hr for the heating requirements of the room. Do not
use the air conditioner as a primary source of heat.
■
The air conditioner is in a heavily occupied room, or heat-
producing appliances are in use in the room. Use exhaust
vent fans while cooking or bathing and try not to use heat-
producing appliances during the hottest part of the day. A
higher capacity air conditioner may be required, depending
on the size of the room being cooled.
Temperature on display does not match room
temperature
■
When the compressor and fan motor turn off during
Power Saver mode, or after you turn off the unit, a lower
temperature reading than the actual room temperature
may be displayed for a short period of time. This lower
temperature reading is caused by the temperature sensor
being located close to the cold evaporator coil. The actual
room temperature will display within a few minutes.
Air conditioner cycles on and off too much, or does not
cool/heat room in cooling/heating mode
■
■
The Mode or Fan control is set to Power Saver (on some
models). Use Power Saver only when you are asleep or away
from home, since the fan does not circulate the room air
continuously. Use Low Cool, Medium Cool or High Cool for
your best comfort.
Water drips from cabinet into your house
The air conditioner is not properly sized for your room.
Check the cooling capabilities of your room air conditioner.
Room air conditioners are not designed to cool multiple
rooms.
■
The air conditioner is not properly leveled. The air
conditioner should slope slightly downward toward the
outside. Level the air conditioner to provide a downward
slope toward the outside to ensure proper drainage. See the
Installation Instructions.
■
■
The filter is dirty or obstructed by debris. Clean the filter.
The inside evaporator and outside condenser coils are
dirty or obstructed by debris. See “Annual Maintenance.”
NOTE: Do not drill a hole into the bottom of the metal base
and condensate pan.
Assistance or Service
For further assistance
For assistance, service or replacement parts
If you need further assistance, you can write to ask any questions
or tell us about your concerns to:
For service assistance or to locate factory-authorized parts,
call our Customer Service Center at 210-357-4400, or your
nearest authorized service center.You also can visit the "Dealer
Friedrich Service Center.
Friedrich Air Conditioning Co.
Customer Assurance
P.O. Box 1540
San Antonio, TX 78295-1540
Or email: [email protected]
Please include a daytime phone number in your
correspondence.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Friedrich Air Conditioning Company
P.O. Box 1540
San Antonio, TX 78295
210.357.4400
ROOM AIR CONDITIONERS
LIMITED WARRANTY
FIRST YEAR
ANY PART: If any part supplied by FRIEDRICH fails because of a defect in workmanship or material within twelve months from
date of original purchase, FRIEDRICH will repair the product at no charge, provided room air conditioner is reasonably accessible
for service. Any additional labor cost for removing inaccessible units and/or charges for mileage related to travel by a Service
Agency that exceeds 25 miles one way will be the responsibility of the owner. This remedy is expressly agreed to be the exclusive
remedy within twelve months from the date of the original purchase.
SECOND THROUGH FIFTH YEAR
SEALED REFRIGERANT SYSTEM: If the Sealed Refrigeration System (defined for this purpose as the compressor, condenser
coil, evaporator coil, reversing valve, check valve, capillary, filter drier, and all interconnecting tubing) supplied by FRIEDRICH in
your Room Air Conditioner fails because of a defect in workmanship or material within sixty months from date of purchase,
FRIEDRICH will pay a labor allowance and parts necessary to repair the Sealed Refrigeration System; PROVIDED FRIEDRICH will
not pay the cost of diagnosis of the problem, removal, freight charges, and transportation of the air conditioner to and from the
Service Agency, and the reinstallation charges associated with repair of the Sealed Refrigeration System. All such cost will be the
sole responsibility of the owner. This remedy is expressly agreed to be the exclusive remedy within sixty months from the date of the
original purchase.
APPLICABILITY AND LIMITATIONS: This warranty is applicable only to units retained within the Fifty States of the U.S.A., District
of Columbia, and Canada. This warranty is not applicable to:
1. Air filters or fuses.
2. Products on which the model and serial numbers have been removed.
3. Products which have defects or damage which results from improper installation, wiring, electrical current
characteristics, or maintenance; or caused by accident, misuse or abuse, fire, flood, alterations and/or misapplication
of the product and/or units installed in a corrosive atmosphere, default or delay in performance caused by war,
government restrictions or restraints, strikes, material shortages beyond the control of FRIEDRICH, or acts of God.
OBTAINING WARRANTY PERFORMANCE: Service will be provided by the FRIEDRICH Authorized Dealer or Service
Organization in your area. They are listed in the Yellow Pages. If assistance is required in obtaining warranty performance, write
to: Room Air Conditioner Service Manager, Friedrich Air Conditioning Co., P.O. Box 1540, San Antonio, TX 78295-1540.
LIMITATIONS:
THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER WARRANTIES. Anything in the warranty
notwithstanding, ANY IMPLIED WARRANTIES OF FITNESS FOR PARTICULAR PURPOSE AND/OR MERCHANTABILITY
SHALL BE LIMITED TO THE DURATION OF THIS EXPRESS WARRANTY. MANUFACTURER EXPRESSLY DISCLAIMS AND
EXCLUDES ANY LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGE FOR BREACH OF ANY EXPRESSED OR
IMPLIED WARRANTY.
NOTE: Some states do not allow limitations on how long an implied warranty lasts, or do not allow the limitation or exclusion of
consequential or incidental damages, so the foregoing exclusions and limitations may not apply to you.
OTHER: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
PROOF OF PURCHASE: Owner must provide proof of purchase in order to receive any warranty related services.
All service calls for explaining the operation of this product will be the sole responsibility of the consumer.
All warranty service must be provided by an Authorized FRIEDRICH Service Agency, unless authorized by FRIEDRICH prior to
repairs being made.
(10-04)
66121417 (1-07)
Printed in the U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|