PCM 240 • Installation Guide
IMPORTANT SAFETY INSTRUCTIONS
Read all instructions before starting installation.
When using this accessory, basic precautions should always be followed, including the following:
WARNING: Risk of Personal Injury. Maximum setup load for the PCM is 50 lbs (22.7 kg).
SAVE THESE INSTRUCTIONS
NOTE: Refer to local building standards and codes to verify that the installation will meet the regulatory requirements.
Observe all local and national building and safety codes, UL requirements, and ADA accessibility guidelines.
WARNING: Risk of Personal Injury and property damage. Do not exceed specified weight limits of any component of
the installation. Follow the manufacturer's specifications and installation instructions.
The Extron PCM 240 Drop Ceiling Projector Mount is used for hanging
PoleVault® System AV products and various projectors.
Base
Plate
The PCM is installed above the drop ceiling and secures the adjustable
pipe in a pass-through pipe adapter plate. The pipe then supports the
mounting of the Extron PMK 550 and UPB 25 projector bracket.
1-gang and 2-gang Accessory Mounting
Points (for Power Sockets, for example)
Pipe
Adapter
The key components of the PCM 240 are shown in figure 1.
Also included in the kit are:
4 turnbuckles, 5 lag eye bolts, 5 concrete anchors, 2 cable clamps,
1 safety wire – 15 feet, 2 tie wires – 30 feet, 4 T-frame screws, 4
adhesive pads, escutcheon ring.
Pipe Adapter Plate
Lock Nuts (4)
T-frame
Securing
Screws (4)
Pipe Adapter
Set Screws (2)
Pre-Installation
Determine the exact location of the installation on the drop ceiling.
Consider the following:
•
•
The vertical and horizontal offsets of the projector from the proposed
location.
The projector dimensions relative to the image target.
NOTE: See the projector manual for details.
Installation
Step 1 — Mark the Frame and Cut the Ceiling Tile.
Figure 1. PCM 240 Parts
a. At the location for the projector, identify the ceiling tile and T-frame
where the PCM will be installed.
b. Remove the predetermined ceiling tile and mark the maximum and
minimum throw distances of the projector on the T-frame (see
figure 2).
X"
Projector
Front
TIP: Mark the screen direction on the back of the tile to
help with orientation of the tile when replacing it after
cutting�
Y"
T-frame
c. Place the PCM base plate over the T-frame, between the two marks.
Lightly tighten the T-frame securing screws.
Minimum and
Maximum
Throw Distance Marks
d. Mark the location of the PCM base plate on the T-frame to aid in
replacing it in the correct location.
e. Measure the distances X and Y (see figure 2) from the inner vertical
section of the front and left T-frame runners to the center of the
Pipe Adapter Plate.
Figure 2. Minimum and Maximum
Throw Distances
1
Download from Www.Somanuals.com. All Manuals Search And Download.
f. Loop the safety cable through the center anchor or lag eye bolt,
attach it to the plate center holes (figure 6) and secure it with the
cable clamps.
Secure PCM to frame
(from either side)
PCM
g. Cut appropriate lengths of the supplied tie wire.
Loop the wire through the anchors or lag eye bolts and the
turnbuckles, then twist the wire around itself at least five times.
T-frame
h. Tighten the turnbuckles by hand (see figure 6), and level the plate
so that it just rests on the grid.
ATTENTION: Potential Damage to Property.
• The four hanging wires should be taut, taking
the full weight of the completed installation.
• Overtightening the turnbuckles could cause
the T-bar assembly to be lifted, making the
suspended ceiling bowed and unsafe.
Adjust the turnbuckles to take
up any slack in the hanging wire.
Figure 6. Adjust the Turnbuckles.
j.
Tighten the four T-frame securing screws on the PCM.
Step 4 — Final Installation.
The PCM 240 comes with a threaded pipe adapter installed in the adapter
plate. This allows for an Extron PMP projector mounting pole to be fitted.
To fit the mounting pole, do the following:
a. Back out the set screws on the pipe adapter/adapter plate assembly.
b. Screw the pole into the adapter. A minimum of three full turns is
required to safely secure the pole in place
c. Secure the pole in place by tightening down the set screw on the
pipe adapter/adapter plate assembly. Cabling for the projector can
be accessed through the cut-out in the PMP pole.
d. Other optional accessories can also be installed at this point. These
include the Extron PMK 350, a low profile, two product mounting
kit, and the UPB 25, a Universal Projector Mounting Bracket suitable
for most projectors weighing up to 25 pounds.
e. Complete any further device installation according to the relevant
device manual.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
PCM 240 • Installation Guide (Continued)
Specifications
General
Maximum load capacity������������������ 50 lbs (22�7 kg)
Material ����������������������������������������� Steel plate, Tie wire: steel, 14 AWG, 70,000 psi tensile strength
Dimensions
Base plate�������������������������������� 25�8” L x 8�0” W x 1�2” D (65�5 cm L x 20�3 cm W x 2�9 cm D)
Product weight������������������������������� 5�6 lbs (2�5 kg
Shipping weight����������������������������� 9 lbs (5 kg)
Vibration���������������������������������������� ISTA 1A in carton (International Safe Transit Association)
Regulatory compliance
Safety�������������������������������������� CE; c-UL, UL for use with UL Listed mount and projector; OSHPD anchorage pre-approval
Warranty���������������������������������������� 3 years parts and labor
NOTE: Specifications are subject to change without notice.
25.80 [655.32]
2X 14.612 [371.14]
9.125 [231.78]
2X 8.500 [215.90]
1.15 [29.21]
4X Ø.19 [Ø4.78] THRU
2X .563 [14.288]
2X .50 [12.70]
2X .563 [14.288]
2.50 [63.51]
.60 [15.24]
2X 1.00 [25.40]
3.00 [76.20]
2.00 [50.80]
8.00 [203.20]
2X 7.000 [177.800]
6.80 [172.72]
2X 6.00 [152.40]
2.00 [50.80]
2X 10-32 UNF - 2B
EXTRUDED .13 [3.18]
2X R1.063 [R26.99]
4X R.107 [R2.71]
2X .12 [3.00]
4X Ø.31 [Ø7.95] THRU
2X 11.187 [284.15]
16.331 [414.80]
2X 1.47 [37.33]
(1.13 [28.58])
4.531 [115.09]
2X .39 [9.86]
BOTH SIDES
3X .260 [6.604] X .500L [12.700]
OBROUND
23.40 [594.36]
2X 1.13 [28.58]
2X .70 [17.78]
2X 1.00 [25.40]
3X Ø.266 [Ø6.76] THRU
.14 [3.48]
23.67 [601.32]
Figure 7. PCM 240 Dimensions
Extron Headquarters
Extron Asia
Extron China
Extron Korea
+1�800�633�9876 (Inside USA/Canada Only)
+65�6383�4400
+86�21�3760�1568)
+82�2�3444�1571
+31�33�453�4040
+81�3�3511�7655
+971�4�2991800
+91�80�3055�3777
© 2012 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
68-1180-01
Rev D
4
Download from Www.Somanuals.com. All Manuals Search And Download.
08 12
|