Hand Held Steam Cleaner
OWNER’S MANUAL
Model SC500
120V., 60Hz., 1600 Watts
For information or assistance:
EURO-PRO Operating LLC
94 Main Mill Street, Door 16
Plattsburgh, NY 12901
Tel.: 800-798-7398
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE & MAINTENANCE
ADDITIONAL IMPORTANT SAFEGUARDS cont.
CAUTION: This appliance must be
Cleaning the Nozzles:
1. To avoid circuit overload, do not operate another appliance on the same socket (circuit)
2. If an extension cord is absolutely necessary, a 15 ampere 14 gage cord should be used.
Cords rated for less amperage may overheat. Care should be taken to arrange cord so
that it cannot be pulled or tripped over.
unplugged from the electrical outlet
and allowed to cool down before
performing any cleaning or
Your steamer should not normally require
cleaning, however, should you notice a
marked decrease in steam output it may
be necessary to remove mineral deposit
build-up from the nozzle orifice. First
ensure that there is water in the tank. If
tank is empty, fill with water, (we
maintenance tasks on the unit.
3. Do not leave unattended when the system is connected to a power supply/electrical outlet.
•
•
Let the appliance cool down
completely before cleaning or storing.
Depress the trigger before opening
the safety cap in order to release any
residual pressure in the boiler.
recommend using purified or
SAVE THESE INSTRUCTIONS
demineralized water), then re-start unit
noting whether steam output is normal. If
steam output is still low, follow these
cleaning instructions:
•
Empty all water from the water tank
after each use.
FOR HOUSEHOLD USE ONLY
•
•
Store in a dry, cool place.
1. Unplug steam cleaner from wall
outlet.
A periodic rinse of your steam cleaner
will free it from deposits. This is
recommended every 10-15 tankfulls
to free up any scale deposits. Fill the
boiler with water and shake
WARNING: This appliance is equipped with a
grounded-type 3-wire cord (3-prong
plug). This plug will only fit into an
electrical outlet made for a 3-prong
plug. This is a safety feature. If the
plug should fail to fit the outlet, contact
an electrician to replace the outlet. Do
not attempt to defeat the safety
2. Depress trigger to release any
residual pressure in the boiler.
3. Use a small diameter stiff metal
wire such as a straightened metal
paperclip and carefully insert the
end of the wire into the nozzle
orifice. See illustrations below.
4. Move wire back and forth several
times to remove any deposits.
5. Reconnect appliance to power
outlet, switch on and note steam
output.
vigorously. Tilt the cleaner upside
down to empty the boiler of water and
any scale deposits.
purpose of the grounding pin, part of
the 3-prong plug.
6. If steam performance does not
improve, repeat steps #1 through #4.
Paperclip
9
2
Download from Www.Somanuals.com. All Manuals Search And Download.
USAGE SUGGESTIONS FOR PROFESSIONAL
PORTABLE STEAMER
GETTING TO KNOW YOUR PROFESSIONAL
PORTABLE STEAMER
Window, Glass Surfaces and Mirrors
Blinds
Use the window squeegee. Work with the
steam on using top to bottom movements.
Use the squeegee with the steam to clear
Use the detail brush to clean blinds.
Move the brush over the surface, allowing
enough time for the vapor to penetrate.
the water from the glass. To do this without Work quickly on PVC blinds. Test for
leaving streaks, use lateral movements
from the top to the bottom of the surface.
color fastness on fabric blinds before
using.
Refrigerator
-
Use the concentrator
Fiberglass or Stainless Steel Surfaces
nozzle alone to blow away dirt in the ice
machine and on door seals. The vapor
will not dry out or crack the seals as
chemicals often do. Can openers and
other kitchen equipment can be easily
cleaned with the detail brush on the
concentrator nozzle to get into all the
nooks and crannies.
To clean microwaves or other small
appliances use the detail brush for small
areas.
Note: When cleaning small electrical
appliances always unplug them from
outlet before cleaning.
Use the detail brush. Slowly move the
brush over the surface to be cleaned.
The steam will emulsify the dirt and
grease on the surface. Follow behind
with a 100% cotton towel to remove
excess moisture and residue.
Tip: An old idea for polishing stainless
steel is to wipe it down with seltzer soda
water after it is cleaned.
21
Soap Scum
Soap scum dissolves almost immediately
under a combination of heat and
moisture. Rinse the surface with a small
amount of water afterwards.
Clothing
A steam cleaning system is excellent for
removing wrinkles from fabrics. Simply
“vaporize” the surface from a distance
(12”-16”) The dry steam removes wrinkles
without leaving the fabric wet like ordinary
fabric steamers do.
Note: Soap scum sometimes will develop
a hard surface from waterborne minerals.
If this is the case, use the detail brush to
break up this surface - or spray or wipe
first with lemon, vinegar or seltzer soda
water to soften the minerals.
Moving too slowly can dry out the soap
scum and cause it to granulate on the
surface. The surface will have a gritty
feel. If this happens, apply vapor to the
surface with the detail brush again and re-
clean.
Upholstery
Use the garment diffuser head with the
cleaning bonnet. Use fast, light strokes,
avoid getting the fabric wet. Be patient
with stubborn spots; work on a spot
gently for no more than a minute at a
time, then wait five minutes for the area
to dry and repeat. Use circular
1. Safety Cap
11. Hose
2. Shoulder Strap Hook
3. Locking Trigger Button
4. Trigger Release
5. Handle
6. Power Cord
7. Main Unit
8. Filling Flask
9. Hose/Unit Connector
10. Indicator Light
12. Cleaning Bonnet
13. Hose/Accessory Connector
14. Window Squeegee
15. Garment Diffuser Head
16. Angle Adapter
17. Detail Brush (2)
18. Concentrator Nozzle (2)
19. Nozzle
Bathroom Areas
To clean the bathtub or shower area, use
the detail brush for grout, shower door
tracks, hard to get areas and heavily
soiled areas. The window squeegee will
be the most efficient way to clean the rest
of the area. Allow plenty of time for the
heat to penetrate the surface. This is
especially helpful in the shower area if
there is tile or grout.
movements or back-and-forth and side-
to-side movements to get all sides of
surface fibers. Finish with a brushing in
one direction that will give the fabric a
uniform appearance.
20. Shoulder Strap Loop
21. Shoulder Strap
Caution: Always determine the color-
fastness of any fabric - especially with
reds or blues - by taking a clean, moist,
warm towel and gently rubbing a small
area as far down on the back or other out
of the way place on the furniture as
possible. If color comes off on the towel,
you may need to have the piece dry
cleaned.
Technical Specifications
To clean sanitary fixtures, use
concentrator nozzle with or without detail
brush.
Voltage:
120V., 60Hz.
Power:
Water Capacity:
1600 Watts
20 U.S. Fl. Oz.(600 c.c.)
To clean the sink and faucets, use detail
brush.
3
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS cont.
FEATURES
Cleaning Bonnet
Your Hand Held Steam Cleaner utilizes pressurized steam to remove tough grease,dirt
and grime. Steam is nature’s purest and most powerful cleaner for safely cleaning all hard
surfaces in your home without harsh chemicals, thus being perfectly ecological. The appliance has
various attachments so that it can be used for many purposes such as:
Tips On How To Use Your Steam
Cleaner
Water
The cleaning bonnet is used with the
garment diffuser head. Just slip it
over the attachment. This can be
used to clean upholstery.
•
•
Use tap water for all your cleaning
needs.
However, if you live in an area with
hard water, use demineralized/
distilled water when steaming light
colored fabrics to eliminate the
possibility of hard water stains.
1. Clean upholstery, sealed grout, bathroom/kitchen tile, stovetops.
2. Easy to clean difficult to reach areas with the angle adapter or concentrator such as
faucets, etc.
3. Ideal for windows, mirrors, glass doors, etc.
4. Clean fabrics, window coverings, pillows, bedding etc.
5. Clean hard surface areas such as counters, sinks, shower door tracks, etc.
IMPORTANT: Do NOT add cleaning
solutions, scented perfumes, oils or any
other chemicals to the water used in
this appliance. Use tap water or
distilled/purified water if the tap
water in your area is very hard.
WARNING: Your Hand Held Steam Cleaner is designed to clean hard
surfaces and upholstery that will withstand high heat. Do not use
on soft plastics,unsealed wood and cold glass. On surfaces that
have been treated with wax or some no wax floors, the sheen
may be removed by the heat and steam action. Do not use on
unsealed wood. This could cause the wood grain to rise. It is
therefore recommended to test an isolated area of the surface to
be cleaned before proceeding.
Attaching the Hose
To attach the hose to the concentrator
nozzle, align the two guide pins inside
the hose/unit connector with the guide
pin slots on the nozzle. Push the hose
in and turn clockwise 90° to lock the
hose in place. See illustration below.
Efficient Work
•
•
•
For vertical surfaces, wipe always
from the top down, in this way the
dirty water will not soil surfaces
already cleaned.
Avoid changing brushes back and
forth while cleaning. Start with the
smallest brush to clean tight spots
and corners first.
CAUTION: Do not plug in the machine during filling. Use a grounded
receptacle. Use only a heavy duty extension cord rated for 15
amps - Do not use an ordinary extension cord.
Lock
Wipe dirt as soon as possible,
otherwise it will dry and re-adhere
to the surface.
IMPORTANT: Do NOT add cleaning solutions, scented perfumes, oils or
Unlock
any other chemicals to the water used in this appliance.
Use regular water or distilled/purified water if the tap
water in your area is very hard.
Hints
The Professional Portable Steamer
has many uses many of which will not
be mentioned in this owner's manual.
This is meant only to give you a
general idea of what can be achieved
with the unit. However, the ways in
which to use the units and the
To attach the concentrator nozzle to
the hose, align the two guide pins
inside the concentrator nozzle with the
guide pin slots on the hose/accessory
connector. Push the concentrator
nozzle in and turn clockwise to lock it
on to the hose. See illustration below.
brushes are in most cases universal.
It is most helpful to always have the
micro fiber cloth or a terry cloth towel
or paper towel ready to use for
removal of moisture and residue.
100% white cotton towels work best.
You can clean the brushes with your
steam cleaner. When cleaning the
detail brush, use a pair of pliers to
hold the brush or place in the basket
of your dishwasher.
Lock
Unlock
Note: Wipe immediately before the
cleaned area dries. When cleaning
the oven, use the detail brush to clean
around the elements, drip trays,
cracks, crevices, and hard to reach
areas.
You can only attach the accessories to
the hose using the concentrator
nozzle. i.e. angle adapter, detail brush,
window squeegee, etc.
7
4
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS cont.
ATTACHMENTS
Concentrator Nozzle
Using the Locking Trigger Button
Window Squeegee
How To Assemble & Use
The steam cleaner has a locking trigger
button. As you push down on the trigger
you will get more steam. The trigger will
lock when you have pushed it all the
way. To unlock the trigger, just press
down on the trigger release and the
trigger will pop up, stopping the flow of
steam.
CAUTION: When cleaning windows,
always avoid any sudden changes in
temperature to prevent glass breakage
or cracks.
IMPORTANT: Always insure that the
unit is “UNPLUGGED” from the wall
receptacle prior to initial filling or re-filling
the water tank. Never attempt to fill this
unit under a water tap, always use the
filling flask provided. Failure to follow
these steps will cause the water tank to
overfill and may pose an electrical safety
hazard.
Step 1: Before filling the steam cleaner,
make sure that the unit is NOT
plugged in.
Step 2: Turn Safety Cap counter
clockwise until removed.
To attach the concentrator nozzle to the
nozzle of the unit, align the pins on the
concentrator nozzle with the slots on the
appliance. (See illustration.) Push the
attachment onto the nozzle until it stops
against the appliance body. Turn in a
clockwise direction 90°. The attachment
is now locked into position.
To attach the window squeegee to the
garment diffuser head, place the two
hinges at the back of the window squeegee
(see illustration) into the two open tabs that
are at the back of the garment diffuser
head. Swing the window squeegee up
against the bottom of the garment diffuser
head until the locking tab engages.
Refilling With Water
Step 1: Disconnect electrical power
cord from wall outlet.
Step 2: Press trigger button until all
pressure has been released.
Carefully unscrew safety
cap.
Step 3: Allow the unit to cool for
approximately 5 minutes
before refilling with water.
Step 4: Slowly pour water using the
filling flask into the boiler.DO
NOT Fill Under a faucet,
use the filling flask
Step 3: Add 20 fl. oz (600 cc) of water
using the filling flask provided.
Do not overfill. Replace
Safety Cap by turning
clockwise - press down firmly to
tighten. Heating time is
approximately 6 minutes. Filling
the boiler with hot water will
shorten heat up time.
To remove the
window
provided. DO NOT
squeegee from
the garment
diffuser head,
just push your
thumb against
the locking tab
on the window
squeegee.
Step 4: Plug the unit into a standard
120 volt wall receptacle. The
power “On” light (Red) will light
up.
Step 5: Allow approximately 3-5
minutes for water vapor to
reach its working
temperature and pressure.
When unit is ready for use the
red light will change to Green.
Step 6: At the start, some water will
come out from the nozzle. This
is normal.
NOTE: Disconnect steam cleaner from
wall outlet before refilling. It is time to refill
your steam cleaner when there is no more
steam coming out of the nozzle. Because
the water tank is pressurized, use caution
when opening to refill. Depress the trigger
button while you unscrew the safety cap
counterclockwise. Always let unit cool for
5 minutes before refilling the unit with
water.
OVERFILL. Always leave
approximately 2 1/2 inches
between the top of the unit
and the water level.
Small Detail Brush / Angle Adapter
Both the angle adapter and the small detail
brushes can only be used directly on the
concentrator nozzle. When using with the
concentrator nozzle, push the attachment
onto the end of the concentrator nozzle.
Step 5: Release the locking trigger.
Step 6: Screw safety cap back on t
he appliance and plug
appliance back into wall
outlet. Steam will start to be
produced as before.
Attaching the Shoulder Strap
Using the detachable
shoulder strap allows
for greater freedom of
movement when both
hands are needed for
various cleaning tasks.
To attach the shoulder
strap to the steam
Garment Diffuser Head
cleaner, simply
snap the shoulder
You can use the garment head diffuser
with the hose or alone on the unit itself. To
attach, align the pins on the
garment head diffuser with
the slots on the appliance.
strap hooks onto the
connecting rings on the
unit body. When using
the steam cleaner
with the shoulder strap,
avoid rocking or tilting
the unit excessively as
this may cause water to
enter the hose and be
discharged along with the steam.
WARNING: This appliance is under
pressure. After every use, press trigger
button until all pressure has been
released before removing safety cap.
Either concentrator nozzle or hose must
be connected in order for the trigger to
operate. Allow unit to cool for three (3)
minutes before refilling.
CAUTION: When refilling the appliance
while it is still hot, the first drops of
water might bubble up.
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
|