Eiki Projector EIP 250 User Manual

EIP-2600

EIP-250

EIP-2600

OWNER’S MANUAL

EIKI INDUSTRIAL CO., LTD.

Download from Www.Somanuals.com. All Manuals Search And Download.

Before using the projector, please read this owner’s manual carefully.

Introduction

ENGLISH

1. WARRANTY

This is to assure that you immediately receive the full benefit of the parts, service and labor

warranty applicable to your purchase.

2. CONSUMER PRODUCT SAFETY ACT

To ensure that you will promptly receive any safety notification of inspection, modification,

or recall that EIKI may be required to give under the 1972 Consumer Product Safety Act,

PLEASE READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.

U.S.A. ONLY

WARNING: High brightness light source. Do not stare into the beam of light, or view

directly. Be especially careful that children do not stare directly into the

beam of light.

WARNING: To reduce the risk of fire or electric shock, do not expose

this product to rain or moisture.

See bottom of projector.

The lightning flash with arrowhead sym-

bol, within an equilateral triangle, is in-

tended to alert the user to the presence

of uninsulated “dangerous voltage”

within the product’s enclosure that may

be of sufficient magnitude to constitute

a risk or electric shock to persons.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT REMOVE SCREWS

EXCEPT SPECIFIED USER

SERVICE SCREW.

CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER.

NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The exclamation point within a triangle

is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in

the literature accompanying the product.

PRODUCT DISPOSAL

This product utilizes tin-lead solder, and lamp containing a small amount

of mercury. Disposal of these materials may be regulated due to

environmental considerations. For disposal or recycling information,

please contact your local authorities, the Electronics Industries Alliance:

www.eiae.org, the lamp recycling organization www.lamprecycle.org,

or 1-800-242-3454.

U.S.A. ONLY

Caution Concerning Lamp Replacement

See “Replacing the Lamp” on page 52.

Authorized representative responsible for the European Union Community Market

EIKI Deutschland GmbH

E.U. ONLY

Am Frauwald 12, 65510 Idstein

Download from Www.Somanuals.com. All Manuals Search And Download.

WARNING: FCC Regulations state that any unauthorized changes or modifications to

this equipment not expressly approved by the manufacturer could void

the user’s authority to operate this equipment.

U.S.A. ONLY

For EIP-2600

INFORMATION

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the owner’s manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference, in which case the user will be required to

correct the interference at his own expense.

U.S.A. ONLY

The enclosed computer cable must be used with the device. The cable is provided to

ensure that the device complies with FCC Class A verification.

U.S.A. ONLY

WARNING:

This is a Class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

For EIP-250

INFORMATION

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the owner’s manual, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV technician for help.

U.S.A. ONLY

Declaration of conformity

EIKI PROJECTOR, MODEL EIP-250

This device complies with Part 15 of the FCC rules. Operation is subject to the following

conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired

operation.

Responsible Party:

EIKI INTERNATIONAL, INC.

30251 Esperanza Rancho Santa Margarita, CA 92688-2132

TEL: 800-242-3454

U.S.A. ONLY

Download from Www.Somanuals.com. All Manuals Search And Download.

How to Read this Owner’s Manual

■ The specifications are slightly different, depending on the model. However, you can connect and

operate all models in the same manner.

•

In this owner’s manual, the illustration and the screen display are simplified for explanation, and

may differ slightly from the actual display. The examples used throughout this manual are based

on the EIP-2600 model.

Using the Menu Screen

ENTER button

Adjustment buttons (P/R/O/Q)

MENU/HELP button

ENTER button

Adjustment buttons

(P/R/O/Q)

Buttons used in

this operation

RETURN button

• Press RETURN to return

to the previous screen

when the menu is

displayed.

MENU/HELP button

Menu Selections (Adjustments)

Example: Adjusting “Bright”.

• This operation can also be performed by using the buttons on the projector.

Button used in

this step

Example: “Picture” screen menu for

Press MENU/HELP.

COMPUTER (RGB) input

(EIP-2600)

• The “Picture” menu screen for the se-

lected input mode is displayed.

Menu item

Press Q or O and select“Picture”

to adjust.

Picture

SCR - ADJ

PRJ - ADJ

Standard

Help

Picture Mode

Contrast

Bright

Red

On-screen

display

Blue

CLR Temp

BrilliantColor^TM

C.M.S. Setting

C.M.S.

DNR

Off

Lamp Setting

Reset

Bright

SEL./ADJ.

ENTER

END

Info

Note

........Indicates safeguards for using the projector.

.........Indicates additional information for setting up and operating the

projector.

For Future Reference

Maintenance

Troubleshooting

Index

P. 49

PP. 63 and 64

P. 67

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

Preparing

Introduction

Useful Features

How to Read this Owner’s Manual ....... 3

Contents ............................................... 4

IMPORTANT SAFEGUARDS ............... 6

How to Access the PDF Owner’s

Manuals .............................................. 9

Accessories ........................................ 10

Part Names and Functions ................. 11

Projector ............................................... 11

Rear View ............................................. 12

Inserting the Batteries .......................... 14

Usable Range ...................................... 15

Operating with the Remote Control.... 32

Displaying and Setting the

Break Timer........................................ 32

Displaying the Pointer .......................... 32

Using the Spot Function ...................... 32

Switching the Eco+Quiet Mode ........... 32

Auto Sync (Auto Sync Adjustment) ..... 33

Freezing a Moving Image .................... 33

Selecting the Picture Mode .................. 33

Displaying an Enlarged Portion of

an Image ............................................ 33

Using the Remote Control as the

Wireless Computer Mouse ................ 34

Menu Items ......................................... 35

Using the Menu Screen ...................... 38

Menu Selections (Adjustments) ........... 38

Picture Adjustment (“Picture” Menu) ... 40

Selecting the Picture Mode .................. 40

Adjusting the Image ............................. 41

Adjusting the Color Temperature ......... 41

Adjusting the Colors............................. 41

Progressive........................................... 42

Reducing Image Noise (DNR) ............. 42

Lamp Setting ........................................ 42

Adjusting the Projector Image

(“SCR - ADJ” Menu) ......................... 43

Setting the Resize Mode ...................... 43

Adjusting the Image Position ............... 43

Keystone Correction ............................ 43

Setting the On-screen Display ............. 43

Closed Caption .................................... 44

Selecting the Background Image ........ 44

Selecting the Setup Guide ................... 44

Reversing/Inverting Projected

Quick Start

Quick Start .......................................... 16

Setup and Projection ............................ 16

Setup

Setting up the Projector ...................... 18

Setting up the Projector ....................... 18

Standard Setup (Front Projection) ....... 18

Ceiling-mount Setup ............................ 18

Projection (PRJ) Mode ......................... 19

Screen Size and Projection Distance .. 20

Connections

Connecting the Projector to

Other Equipment .............................. 21

Controlling the Projector by

a Computer....................................... 24

Connecting the Power Cord ............... 24

Images ............................................... 44

Selecting the On-screen Display

Language........................................... 44

Adjusting the Projector Function

Using

(“PRJ - ADJ” Menu) .......................... 45

Auto Sync (Auto Sync Adjustment) ..... 45

Auto Power Off Function ...................... 45

Auto Restart Function .......................... 45

STANDBY Mode ................................... 45

Setting the Confirmation Sound

Basic Operation

Turning the Projector On/Off .............. 25

Turning the Projector on ....................... 25

Turning the Power off (Putting the

Projector into Standby Mode) ........... 25

Image Projection................................. 26

About the Setup Guide ........................ 26

Adjusting the Projected Image ............ 26

Correcting Trapezoidal Distortion ........ 28

Switching the Input Mode .................... 29

Adjusting the Volume ........................... 29

Displaying the Black Screen and

(System Sound) ................................. 45

Speaker Setting .................................... 45

Audio Input (EIP-2600 only) ................. 46

Selecting the Transmission Speed

(RS-232C) .......................................... 46

Fan Mode Setting ................................. 46

System Lock Function .......................... 46

Checking the Lamp Life Status ........... 47

Keylock Function .................................. 47

Turning off the Sound Temporarily .... 29

Resize Mode......................................... 30

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting with the

“Help” Menu ...................................... 48

Utilizing the “Help” Menu Functions .... 48

Reference

Appendix

Maintenance ....................................... 49

Maintenance Indicators ...................... 50

Regarding the Lamp ........................... 52

Lamp..................................................... 52

Caution Concerning the Lamp ............ 52

Replacing the Lamp ............................. 52

Removing and Installing the

Lamp Unit .......................................... 53

Resetting the Lamp Timer .................... 54

Connecting Pin Assignments ............. 55

RS-232C Specifications and

Commands ....................................... 57

Computer Compatibility Chart ............ 62

Troubleshooting .................................. 63

Specifications ..................................... 65

Dimensions ......................................... 66

Index ................................................... 67

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFEGUARDS

CAUTION:Please read all of these instructions before you operate this product

and save these instructions for later use.

Electrical energy can perform many useful functions. This product has been engineered

and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN

POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the

safeguards incorporated in this product, observe the following basic rules for its installation,

use and servicing.

1. Read Instructions

11. Power Sources

All the safety and operating instructions should be

read before the product is operated.

This product should be operated only from the type

of power source indicated on the marking label. If

you are not sure of the type of power supply to

your home, consult your product dealer or local

power company. For products intended to operate

from battery power, or other sources, refer to the

operating instructions.

2. Retain Instructions

The safety and operating instructions should be

retained for future reference.

3. Heed Warnings

All warnings on the product and in the

12. Grounding or Polarization

This product is provided with one of the following

types of plugs. If the plug should fail to fit into the

power outlet, please contact your electrician.

Do not defeat the safety purpose of the plug.

a. Two-wire type (mains) plug.

operating instructions should be adhered to.

4. Follow Instructions

All operating and use instructions should be

followed.

5. Cleaning

b. Three-wire grounding type (mains) plug with a

grounding terminal.

This plug will only fit into a grounding type power

outlet.

Unplug this product from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol

cleaners. Use a damp cloth for cleaning.

6. Attachments

13. Power-Cord Protection

Do not use attachments not recommended by the

product manufacturer as they may cause hazards.

Power-supply cords should be routed so that they

are not likely to be walked on or pinched by items

placed upon or against them, paying particular

attention to cords at plugs, convenience

receptacles, and the point where they exit from the

product.

7. Water and Moisture

Do not use this product near water–for example,

near a bath tub, wash bowl, kitchen sink, or laundry

tub; in a wet basement; or near a swimming pool;

and the like.

14. Lightning

8. Accessories

For added protection for this product during a

lightning storm, or when it is left unattended and

unused for long periods of time, unplug it from the

wall outlet and disconnect the cable system. This

will prevent damage to the product due to lightning

and power-line surges.

Do not place this product on an unstable cart,

stand, tripod, bracket, or table. The product may

fall, causing serious injury to a child or adult, and

serious damage to the product. Use only with a

cart, stand, tripod, bracket, or table recommended

by the manufacturer, or sold with the product. Any

mounting of the product should follow the

manufacturer’s instructions, and should use a

mounting accessory recommended by the

manufacturer.

15. Overloading

Do not overload wall outlets, extension cords, or

integral convenience receptacles as this can result

in a risk of fire or electric shock.

16. Object and Liquid Entry

9. Transportation

Never push objects of any kind into this product

through openings as they may touch dangerous

voltage points or short-out parts that could result

in a fire or electric shock. Never spill liquid of any

kind on the product.

product and cart

combination should be

moved with care. Quick

stops, excessive force, and

uneven surfaces may

cause the product and cart

combination to overturn.

17. Servicing

Do not attempt to service this product yourself as

opening or removing covers may expose you to

dangerous voltage or other hazards. Refer all

servicing to qualified service personnel.

10. Ventilation

Slots and openings in the cabinet are provided for

ventilation to ensure reliable operation of the

product and to protect it from overheating, and

these openings must not be blocked or covered.

The openings should never be blocked by placing

the product on a bed, sofa, rug, or other similar

surface. This product should not be placed in a

built-in installation such as a bookcase or rack

unless proper ventilation is provided or the

manufacturer’s instructions have been adhered to.

Download from Www.Somanuals.com. All Manuals Search And Download.

18. Damage Requiring Service

Unplug this product from the wall outlet and refer

servicing to qualified service personnel under the

following conditions:

19. Replacement Parts

When replacement parts are required, be sure the

service technician has used replacement parts

specified by the manufacturer or have the same

characteristics as the original part. Unauthorized

substitutions may result in fire, electric shock, or

other hazards.

a. When the power-supply cord or plug is

damaged.

b. If liquid has been spilled, or objects have fallen

into the product.

20. Safety Check

c. If the product has been exposed to rain or water.

d. If the product does not operate normally by

following the operating instructions. Adjust only

those controls that are covered by the operating

instructions, as an improper adjustment of other

controls may result in damage and will often

require extensive work by a qualified technician

to restore the product to normal operation.

e. If the product has been dropped or damaged

in any way.

Upon completion of any service or repairs to this

product, ask the service technician to perform

safety checks to determine that the product is in

proper operating condition.

21. Wall or Ceiling Mounting

This product should be mounted to a wall or ceiling

only as recommended by the manufacturer.

22. Heat

This product should be situated away from heat

sources such as radiators, heat registers, stoves,

or other products (including amplifiers) that

produce heat.

f. When the product exhibits a distinct change in

performance, this indicates a need for service.

• DLP^®and the DLP logo are registered trademarks of Texas Instruments and BrilliantColor^TMis a

trademark of Texas Instruments.

• Microsoft^®and Windows^®are registered trademarks of Microsoft Corporation in the United States

and/or other countries.

• PC/AT is a registered trademark of International Business Machines Corporation in the United States.

• Adobe^®Reader^®is a trademark of Adobe Systems Incorporated.

• Macintosh^®is a registered trademark of Apple Computer, Inc.in the United States and/or other countries.

•

All other company or product names are trademarks or registered trademarks of their respective companies.

• Some IC chips in this product include confidential and/or trade secret property belonging to Texas

Instruments.Therefore you may not copy, modify, adapt, translate, distribute, reverse engineer, reverse

assemble or discompile the contents thereof.

Closed Caption uses Bitstream Vera fonts

Bitstream, Inc.

Permission is hereby granted, free of charge, to any person obtaining a copy of the fonts

accompanying this license (“Fonts”) and associated documentation files (the “Font Software”), to

reproduce and distribute the Font Software, including without limitation the rights to use, copy,

merge, publish, distribute, and/or sell copies of the Font Software, and to permit persons to whom

the Font Software is furnished to do so, subject to the following conditions:

The above copyright and trademark notices and this permission notice shall be included in all copies

of one or more of the Font Software typefaces.

The Font Software may be modified, altered, or added to, and in particular the designs of glyphs or

characters in the Fonts may be modified and additional glyphs or characters may be added to the

Fonts, only if the fonts are renamed to names not containing either the words “Bitstream” or the

word “Vera”.

This License becomes null and void to the extent applicable to Fonts or Font Software that has been

modified and is distributed under the “Bitstream Vera” names.

The Font Software may be sold as part of a larger software package but no copy of one or more of

the Font Software typefaces may be sold by itself.

THE FONT SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR

IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTIES OF MERCHANTABILITY, FITNESS

FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OF COPYRIGHT, PATENT, TRADEMARK,

OR OTHER RIGHT. IN NO EVENT SHALL BITSTREAM OR THE GNOME FOUNDATION BE LIABLE FOR

ANY CLAIM, DAMAGES OR OTHER LIABILITY, INCLUDING ANY GENERAL, SPECIAL, INDIRECT,

INCIDENTAL, OR CONSEQUENTIAL DAMAGES, WHETHER IN AN ACTION OF CONTRACT, TORT OR

OTHERWISE, ARISING FROM, OUT OF THE USE OR INABILITY TO USE THE FONT SOFTWARE OR

FROM OTHER DEALINGS IN THE FONT SOFTWARE.

Except as contained in this notice, the names of Gnome, the Gnome Foundation, and Bitstream

Inc., shall not be used in advertising or otherwise to promote the sale, use or other dealings in this

Font Software without prior written authorization from the Gnome Foundation or Bitstream Inc.,

respectively. For further information, contact: fonts at gnome dot org.

Download from Www.Somanuals.com. All Manuals Search And Download.

Observe the following safeguards when setting up your

projector.

Caution concerning the lamp unit

■ Potential hazard of glass par-

ticles if lamp ruptures.In case

of lamp rupture, contact your

nearest EIKI Authorized

Dealer or Service Center for

replacement.

When using the projector in high-altitude

areas such as mountains (at altitudes of

approximately 1,500 meters (4,900 feet)

or more)

■ When you use the projector in high-altitude

areas with thin air, set “Fan Mode” to “High”.

Neglecting this can affect the longevity of the

optical system.

See “Regarding the Lamp” on

page 52.

Warning about placing the projector in

a high position

■ When placing the projector in a high position,

make certain it is carefully secure to avoid

personal injury caused by the projector fall-

ing down.

Caution concerning the setup of the

projector

■ For minimal servicing and to maintain high

image quality, EIKI recommends that this pro-

jector be installed in an area free from hu-

midity, dust and cigarette smoke. When the

projector is subjected to these environments,

the vents and lens must be cleaned more of-

ten. As long as the projector is regularly

cleaned, use in these environments will not

reduce the overall operation life of the unit.

Internal cleaning should only be performed

by an EIKI Authorized Dealer or Service Cen-

ter.

Do not subject the projector to hard

impact and/or vibration.

■ Protect the lens so as not to hit or damage

the surface of the lens.

Rest your eyes occasionally.

■ Continuously watching the screen for long

hours will cause eye strain. Take regular

breaks to rest your eyes.

Do not set up the projector in places

exposed to direct sunlight or bright light.

■ Position the screen so that it is not in direct

sunlight or room light. Light falling directly on

the screen washes out the colors, making

viewing difficult. Close the curtains and dim

the lights when setting up the screen in a

sunny or bright room.

Avoid locations with extremes of

temperature.

■ The operating temperature of the projector is

from 41°F to 95°F (+5°C to +35°C).

■ The storage temperature of the projector is

from –4°F to 140°F (–20°C to +60°C).

Do not block the exhaust and intake

vents.

Caution regarding placing of the projector

■ Place the projector on a level site within the

adjustment range (9 degrees) of the adjust-

ment foot.

■ Allow at least 11 ¹³/16 inches (30 cm) of space

between the exhaust vent and the nearest

wall or obstruction.

■ Ensure that the intake vent and the exhaust

vent are not obstructed.

■ If the cooling fan becomes obstructed, a pro-

tection circuit will automatically put the pro-

jector into standby mode to prevent overheat

damage. This does not indicate a malfunc-

tion. (See pages 50 and 51.) Remove the pro-

jector power cord from the wall outlet and wait

at least 10 minutes. Place the projector where

the intake and exhaust vents are not blocked,

plug the power cord back in and turn on the

projector. This will return the projector to the

normal operating condition.

■ After the projector is purchased, a faint smell

from the vent may appear when the power is

first turned on. This is normal and is not a

malfunction. It will disappear after the projec-

tor is used for a while.

Download from Www.Somanuals.com. All Manuals Search And Download.

Caution regarding usage of the projector Using the projector in other countries

■ If you are not to use the projector for a long ■ The power supply voltage and the shape of

time or before moving the projector, make

certain you unplug the power cord from the

wall outlet, and disconnect any other cables

connected to it.

the plug may vary depending on the region

or country you are using the projector in.

When using the projector overseas, make

sure you use an appropriate power cord for

the country you are in.

■ If the power cord is unplugged while the cool-

ing fan is running, some parts of the projec-

tor may still be hot. Use caution when han-

dling the projector.

Temperature monitor function

■ Do not carry the projector by holding the lens.

■ When storing the projector, ensure you at-

tach the lens cap to the projector. (See page

11.)

■ Do not expose the projector to direct sunlight

or place next to heat sources. Doing so may

affect the cabinet color or cause deformation

of the plastic cover.

■

If the projector starts to overheat due to setup

problems or blockage of the air vents, “ ” and

” will illuminate in the lower left corner

of the picture. If the temperature continues to

rise, the lamp will turn off, the temperature warn-

ing indicator on the projector will blink, and after

a 60-second cooling-off period the projector will

enter standby mode. Refer to “Maintenance In-

dicators” on page 50 for details.

“

Other connected equipment

■ When connecting a computer or other audio-

visual equipment to the projector, make the

connections AFTER unplugging the power

cord of the projector from the AC outlet and

turning off the equipment to be connected.

■ Please read the owner’s manuals of the pro-

jector and the equipment to be connected for

instructions on how to make the connections.

Info

•

The cooling fan regulates the internal tempera-

ture, and its performance is automatically con-

trolled. The sound of the fan may change dur-

ing projector operation due to changes in the

fan speed. This does not indicate malfunction.

How to Access the PDF Owner’s Manuals

PDF owner’s manuals in several languages are included in the CD-ROM.To utilize

these manuals, you need to install Adobe^®Reader^®on your computer (Windows^®

or Macintosh^®).

Please download Adobe^®Reader^®from the Internet (http://www.adobe.com).

Accessing the PDF Manuals for Windows^®(For Macintosh^®, skip step 2).

1 Insert the CD-ROM in the CD-ROM drive.

2 Double click the “My Computer” icon.

3 Double click the “CD-ROM” drive.

4 Double click the “MANUALS” folder.

5 Double click the model (name of the folder)

that you want to view.

6 Double click the language (name of the

folder) that you want to view.

7 Double click the pdf file to access the pro-

jector manuals.

Note

• If the desired pdf file cannot be opened by double clicking the mouse, start Adobe^®Reader^®first,

then specify the desired file using the “File”, “Open” menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

Accessories

Supplied accessories

Two R-6 batteries

(“AA” size, UM/SUM-3,

HP-7 or similar)

RGB cable

(10' (3.0 m))

Remote control

for EIP-2600

for EIP-250

Lens cap (attached)

DIN-D-sub RS-232C adaptor

(5 ⁵⁷/64" (15 cm))

Power cord*

(1 )

(2)

3 RCA to mini D-sub 15 pin cable

(10' (3.0 m))

For U.S. and Canada, etc. For Europe, except U.K.

(6' (1.8 m))

* Use the power cord that corresponds to

the wall outlet in your country.

• QUICK GUIDE

• Owner’s manual (this manual and CD-ROM)

Optional accessories

■ Lamp unit

■ Storage case

AH-62101

AH-62501

Download from Www.Somanuals.com. All Manuals Search And Download.

Part Names and Functions

Numbers in Z refer to the main pages in this owner’s manual where the topic is

explained.

Projector

Top View

Power

indicator

Lamp indicator

25, 50

Temperature warning

indicator

STANDBY/ON

button

ECO+QUIET button

For lowering the noise

of the cooling fan and

extending the lamp life.

For turning the

power on and

putting the

projector into

standby mode.

VOL (Volume) buttons

(–O/Q+)

For adjusting the

speaker sound level.

ENTER button

For setting

items selected

or adjusted on

the menu.

INPUT buttons (P/R)

For switching input mode.

MENU/HELP button

For displaying

38, 48

adjustment and

setting screens, and

help screen.

KEYSTONE

button

For entering the

Keystone

Correction mode.

Adjustment buttons

(P/R/O/Q)

For selecting menu items.

Front View

Zoom ring

For enlarging/

reducing the picture.

Intake vent

Remote control

sensor

Speaker

Exhaust vent

Focus ring

For adjusting

the focus.

HEIGHT

ADJUST lever

Push both sides of the lens cap

to attach or remove.

Download from Www.Somanuals.com. All Manuals Search And Download.

Part Names and Functions (Continued)

Numbers in Z refer to the main pages in this owner’s manual where the topic is

explained.

Rear View

Terminals

*AUDIO 1 input terminal

S-VIDEO input terminal

Terminal for connecting

video equipment with an

S-video terminal.

COMPUTER/

COMPONENT input

terminal

RS-232C terminal

Terminal for

Terminal for computer RGB

and component signals.

controlling the

projector using a

computer.

*DVI-I input

terminal

Terminal for

DVI digital,

computer RGB

USB terminal

Terminal connecting

with the USB

terminal on the

and component

signals.

computer for using

the supplied remote

control as the

computer mouse.

*AUDIO OUT

terminal

Audio output terminal of

equipment connected to the

audio input terminal.

AUDIO 2 input

terminal

(AUDIO input

terminal for

EIP-250)

MONITOR OUT

terminal

(Output terminal for computer RGB,

component signals. Shared for COM-

PUTER/COMPONENT)

22 ^{VIDEO input}

terminal

Terminal for

connecting video

equipment.

Terminal for connecting a monitor.

* EIP-2600 only

AC socket

Connect the supplied

power cord.

Rear

adjustment

foot

Kensington Security

Standard connector

Using the Kensington Lock

• This projector has a Kensington Security Standard connector for use with a Kensington

MicroSaver Security System. Refer to the information that came with the system for

instructions on how to use it to secure the projector.

Download from Www.Somanuals.com. All Manuals Search And Download.

STANDBY button

ON button

For turning the power

on.

For putting the projector

into the standby mode.

FREEZE button

For freezing images.

COMPUTER, *DVI,

S-VIDEO, VIDEO buttons

For switching to the

AV MUTE button

For temporarily

displaying a black

screen and turning

off the sound.

respective input modes.

BREAK TIMER button

For displaying the

break time.

VOL +/– (Volume)

buttons

For adjusting the

speaker sound level.

MAGNIFY buttons

For enlarging/reducing

part of the image.

PAGE UP/PAGE

DOWN buttons

SPOT button

For displaying the

spotlight.

Same as the [Page Down] and

[Page Up] keys on a computer

keyboard, when with the USB

connection (using a USB cable

or the optional remote

ENTER button

For setting items

selected or adjusted

on the menu.

receiver).

POINTER button

For displaying the

pointer.

R-CLICK/RETURN

button

• For the Right click

when with the USB

connection (using a

USB cable or the

optional remote

receiver).

• For returning to the

previous menu screen

during menu

MOUSE/Adjustment

buttons (P/R/O/Q)

• For moving the

computer cursor when with the USB

connection (using a USB cable or the

optional remote receiver).

• For selecting and adjusting menu

items.

operations.

L-CLICK/EFFECT

button

• For the Left click

when with the USB connection

(using a USB cable or the optional

remote receiver).

• For changing the pointer or spot

area.

MENU/HELP button

For displaying

adjustment and

setting screens, and

help screen.

KEYSTONE button

For entering the

Keystone Correction mode.

RESIZE button

For switching the

picture size

(NORMAL, BORDER,

etc.).

AUTO SYNC button

For automatically

adjusting images when

connected to a computer.

PICTURE MODE

button

For selecting the

appropriate picture.

ECO+QUIET button

For lowering the noise

of the cooling fan and

extending the lamp life.

* EIP-2600 only

Download from Www.Somanuals.com. All Manuals Search And Download.

Part Names and Functions (Continued)

Inserting the Batteries

Pull down the tab on the cover and remove the cover

towards the direction of the arrow.

Insert the batteries.

• Insert the batteries making sure the polarities correctly match

the m and n marks inside the battery compartment.

Insert the lower tab of the cover into the opening,

and lower the cover until it clicks in place.

Incorrect use of the batteries may cause them to leak or explode. Please

follow the precautions below.

Caution

Danger of explosion if battery is incorrectly replaced.

Replace only with alkaline or manganese batteries.

Insert the batteries making sure the polarities correctly match the m and n marks inside the battery

compartment.

•

Batteries of different types have different properties, therefore do not mix batteries of different types.

Do not mix new and old batteries.

This may shorten the life of new batteries or may cause old batteries to leak.

Remove the batteries from the remote control once they have run out, as leaving them in can cause them

to leak.

•

Battery fluid from leaked batteries is harmful to skin, therefore ensure you wipe them first and then remove

them using a cloth.

The batteries included with this projector may run down in a short period, depending on how they are kept.

Be sure to replace them as soon as possible with new batteries.

Remove the batteries from the remote control if you will not be using the remote control for a long time.

Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.

•

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote control sensor

Usable Range

The remote control can be used to control the

projector within the ranges shown in the

illustration.

Note

• The signal from the remote control can be re-

flected off a screen for easy operation. How-

ever, the effective distance of the signal may

differ depending on the screen material.

30°

When using the remote control

•

Ensure that you do not drop it or expose it to

moisture or high temperature.

23n (7 m)

•

The remote control may malfunction under a

fluorescent lamp. In this case, move the pro-

jector away from the fluorescent lamp.

Remote control

signal transmitters

Remote control

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Start

This section shows the basic operation (projector connecting with the computer). For details, see

the page described below for each step.

Setup and Projection

In this section, connection of the projector and the computer is explained using one example.

STANDBY/ON

button

STANDBY button

ON button

INPUT buttons

ENTER button

COMPUTER button

Adjustment buttons

(P/R/O/Q)

KEYSTONE

button

Zoom ring

ENTER button

Focus ring

Adjustment buttons

(P/R/O/Q)

KEYSTONE button

HEIGHT

ADJUST lever

_P. 18

1. Place the projector facing a wall or a screen

2. Connect the projector to the computer and plug the power cord

into the AC socket of the projector

When connecting equipment other than a computer, see

pages 22 and 23.

_PP. 21, 24

3. Remove the lens cap and turn the projector on

On the projector On the remote control

_P. 25

Download from Www.Somanuals.com. All Manuals Search And Download.

4. Adjust the projected image with the Setup Guide

1 After the projector turns on, the Setup Guide appears.

(When “Setup Guide” is set to “On”. See page 44.)

2 Follow the steps in the Setup Guide and adjust the focus, height (angle) and picture size.

3 After adjusting the focus, height (angle) and picture size, press ENTER to finish the Setup

Guide.

_PP. 26, 27

5. Correct trapezoidal distortion

Correcting trapezoidal distortion using Keystone Correction.

On the projector

Shrinks

lower side.

upper side.

On the remote control

_P. 28

6. Select the INPUT mode

Select the “COMPUTER” using INPUT on the projector or COMPUTER on the remote control.

On the On the remote

projector

control

On-screen display (RGB)

COMPUTER

INPUT list

INPUT

RGB

COMPUTER

1024 × 768

DVI-D Computer

DVI-D Video

EIP-2600 only

• When you press INPUT on the projector, the INPUT list appears.

Press '/" to switch the INPUT mode.

_P. 29

7.Turn the computer on

8.Turn the power off

Press STANDBY/ON on the projector or STANDBY on the remote control, and then press the

button again while the confirmation message is displayed to put the projector into standby mode.

On-screen display

On the On the remote

projector

control

_P. 25

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting up the Projector

For optimal image quality, position the projector perpendicular to the screen with the projector’s feet

flat and level. Doing so will eliminate the need for Keystone correction and provide the best image

quality. (See page 28.)

Standard Setup (Front Projection)

■ Place the projector at the required distance from the screen according

to the desired picture size. (See page 20.)

Example of standard setup

Side View

Screen

Lens center

Note

• Refer to page 20 for additional information concerning “Screen Size and Projection Distance”.

Ceiling-mount Setup

■ It is recommended that you use the optional

EIKI ceiling-mount adaptor and unit for this

installation. Before mounting the projector,

contact your nearest EIKI Authorized Dealer

or Service Center to obtain the recommended

ceiling-mount adaptor and unit (sold

separately).

Download from Www.Somanuals.com. All Manuals Search And Download.

Projection (PRJ) Mode

The projector can use any of the 4 projection modes shown in the diagram below. Select the mode

most appropriate for the projection setting in use. (You can set the PRJ mode in “SCR-ADJ” menu.

See page 44.)

■ Table mounted, front projection

[Menu item ➞ “Front”]

■ Ceiling mounted, front projection

[Menu item ➞ “Ceiling + Front”]

■ Table mounted, rear projection

(with a translucent screen)

[Menu item ➞ “Rear”]

■ Ceiling mounted, rear projection

(with a translucent screen)

[Menu item ➞ “Ceiling + Rear”]

Indication of the Projection Image Size and Projection Distance

Example: NORMAL Mode (4:3)

Picture Size

300"

240"

180"

200"

160"

120"

100"

80"

60"

48"

64"

40"

32"

24"

Projection

Distance

_"–5'8

_"–11'4

–

4'11

(1.5 m – 1.7 m)

9'10

3.5 m)

_"–14'2

–

4.3 m)

(3.0 m

_"–28'4

–

12'3

(3.7 m

8.6 m)

24'7

(7.5 m

36'10

(11.2 m)

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting up the Projector (Continued)

Screen Size and Projection Distance

NORMAL Mode (4:3)

Picture (Screen) size

Projection distance [L]

Distance from the lens center

to the bottom of the image [H]

Diag. [ ]

Width

Height

Minimum [L1]

Maximum [L2]

300Љ (762 cm) 610 cm (240Љ) 457 cm (180Љ) 11.2 m (36Ј 10Љ)

—

19 cm (7 ⁹/16Љ)

16 cm (6 ¹⁹/64Љ)

13 cm (5 ³/64Љ)

10 cm (3 ²⁵/32Љ)

8 cm (3 ¹/32Љ)

6 cm (2 ³³/64Љ)

5 cm (2 ¹/64Љ)

4 cm (1 ⁴⁹/64Љ)

4 cm (1 ³³/64Љ)

3 cm (1 ¹/64Љ)

250Љ (635 cm) 508 cm (200Љ) 381 cm (150Љ) 9.4 m (30Ј 9Љ) 10.8 m (35Ј 5Љ)

200Љ (508 cm) 406 cm (160Љ) 305 cm (120Љ) 7.5 m (24Ј 7Љ)

8.6 m (28Ј 4Љ)

6.5 m (21Ј 3Љ)

5.2 m (17Ј 0Љ)

4.3 m (14Ј 2Љ)

3.5 m (11Ј 4Љ)

3.0 m (9Ј 11Љ)

2.6 m (8Ј 6Љ)

1.7 m (5Ј 8Љ)

150Љ (381 cm) 305 cm (120Љ) 229 cm (90Љ)

5.6 m (18Ј 5Љ)

4.5 m (14Ј 9Љ)

3.7 m (12Ј 3Љ)

3.0 m (9Ј 10Љ)

2.6 m (8Ј 7Љ)

2.2 m (7Ј 4Љ)

1.5 m (4Ј 11Љ)

120Љ (305 cm) 244 cm (96Љ)

100Љ (254 cm) 203 cm (80Љ)

80Љ (203 cm) 163 cm (64Љ)

70Љ (178 cm) 142 cm (56Љ)

60Љ (152 cm) 122 cm (48Љ)

40Љ (102 cm) 81 cm (32Љ)

183 cm (72Љ)

152 cm (60Љ)

122 cm (48Љ)

107 cm (42Љ)

91 cm (36Љ)

61 cm (24Љ)

: Picture size (diag.) (in/cm)

L: Projection distance (m/ft)

The formula for picture size and projection distance

[m/cm]

L1 (m) = 0.03745

L2 (m) = 0.04323

[Feet/inches]

L1 (ft) = 0.03745 / 0.3048

L2 (ft) = 0.04323 / 0.3048

L1: Minimum projection distance (m/ft)

L2: Maximum projection distance (m/ft)

H: Distance from the lens center to the bottom of the image (cm/in)

H (cm) = 0.064

H (in) = 0.064 / 2.54

STRETCH Mode (16:9)

Picture (Screen) size

Width

Projection distance [L]

Distance from the lens center to Adjustable range of

the bottom of the image [H]

69 cm (27 ¹⁹/64Љ)

55 cm (21 ⁵³/64Љ)

image position [S]

52 cm (

20 ²⁷/64Љ)

42 cm (

16 ¹¹/32Љ)

Diag. [ ]

Height

Minimum [L1]

Maximum [L2]

250Љ (635 cm) 553 cm (218Љ) 311 cm (123Љ) 10.2 m (33Ј 6Љ) 11.8 m (38Ј 8Љ)

200Љ (508 cm) 443 cm (174Љ) 249 cm (98Љ)

150Љ (381 cm) 332 cm (131Љ) 187 cm (74Љ)

120Љ (305 cm) 266 cm (105Љ) 149 cm (59Љ)

8.2 m (26Ј 9Љ) 9.4 m (30Ј 11Љ)

6.1 m (20Ј 1Љ) 7.1 m (23Ј 2Љ)

4.9 m (16Ј 1Љ) 5.7 m (18Ј 7Љ)

4.1 m (13Ј 5Љ) 4.7 m (15Ј 5Љ)

3.3 m (10Ј 9Љ) 3.8 m (12Ј 4Љ)

42 cm (16 ³

/8Љ)

31 cm (

12 ¹

/4Љ)

33 cm (13 ³/32Љ)

28 cm (10 ⁵⁹/64Љ)

22 cm (8 ⁴⁷/64Љ)

17 cm (6 ³⁵/64Љ)

11 cm (4 ²³/64Љ)

25 cm (

9 ¹³/16Љ)

21 cm (

8 ¹¹/64Љ)

17 cm (

6 ¹⁷/32Љ)

12 cm (

4 ²⁹/32Љ)

8 cm (

3 ¹⁷/64Љ)

100Љ (254 cm) 221 cm (87Љ)

80Љ (203 cm) 177 cm (70Љ)

60Љ (152 cm) 133 cm (52Љ)

40Љ (102 cm) 89 cm (35Љ)

125 cm (49Љ)

100 cm (39Љ)

75 cm (29Љ)

50 cm (20Љ)

2.4 m (8Ј 0Љ)

1.6 m (5Ј 4Љ)

2.8 m (9Ј 3Љ)

1.9 m (6Ј 2Љ)

: Picture size (diag.) (in/cm)

L: Projection distance (m/ft)

The formula for picture size and projection distance

[m/cm]

L1 (m) = 0.0408

L2 (m) = 0.0471

[Feet/inches]

L1 (ft) = 0.0408 / 0.3048

L2 (ft) = 0.0471 / 0.3048

H (in) = 0.27727 / 2.54

L1: Minimum projection distance (m/ft)

L2: Maximum projection distance (m/ft)

H: Distance from the lens center to the bottom of the image (cm/in)

H (cm) = 0.27727

S: Adjustable range of image position (cm/in) See page 43.

S (cm) = 0.20754

S (in) = 0.20754 / 2.54

Note

• Refer to page 18 concerning “Projection distance [L]” and “Distance from the lens center to the

bottom of the image [H]”.

• Allow a margin of error in the values in the diagrams above.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting the Projector to Other Equipment

Before connecting, ensure that the power cord of the projector is unplugged from the AC

outlet and turn off the equipment to be connected. After making all connections, turn on the

projector and then the other pieces of equipment.When connecting a computer, ensure that

it is the last equipment to be turned on after all the connections are made.

IMPORTANT:

Ensure that the appropriate input mode has been selected on the projector before

you turn on the connected equipment.

•

For more details of connection and cables, refer to the owner’s manual of the connecting equipment.

• You may need other cables or connectors not listed below.

Terminals on the Projector

Example:Terminals of EIP-2600

Terminal on

connected equipment

Terminal on the

projector

Equipment

Computer

Cable

RGB cable (supplied)

COMPUTER/

COMPONENT

RGB

output

terminal

mini D-sub 15 pin to DVI cable

(commercially available)

RGB

output

terminal

DVI-I

DVI Digital cable (commercially available)

DVI digital

output

terminal

is only for EIP-2600.

Note

• See page 62 “Computer Compatibility Chart” for a list of computer signals compatible with the projec-

tor. Use with computer signals other than those listed may cause some of the functions to not work.

• A Macintosh adaptor may be required for use with some Macintosh computers. Contact your near-

est Macintosh Dealer.

• Depending on the computer you are using, an image may not be projected unless the

computer’s external output port is switched on. Refer to the specific instructions in your computer

owner’s manual to enable your computer’s external output port.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting the Projector to Other Equipment (Continued)

Terminal on

Terminal on the

projector

Equipment

Cable

connected equipment

Video equipment

HDMI

output

terminal

HDMI to DVI cable

(commercially available)

DVI-I

DVI Digital cable (commercially available)

DVI digital

output

terminal

Component 3 RCA to mini D-sub 15 pin cable

COMPUTER/

COMPONENT

video

output

terminal

(supplied)

S-video

output

S-video cable (commercially available)

S-VIDEO

VIDEO

terminal

Video

output

terminal

Video cable (commercially available)

Camera/Video game

COMPUTER/

COMPONENT

Cables for a camera or a video game/3 RCA

to mini D-sub 15 pin cable (supplied)

Component

video

output

terminal

RCA adaptor plug

(commercially available)

Cables for a camera or a video game

S-VIDEO

VIDEO

S-video

output

terminal

Cables for a camera or a video game

Video

output

terminal

is only for EIP-2600.

Note

• Only for EIP-2600:

- While the projector is connected to video equipment that has an HDMI output terminal, only the

video signal can be input to the projector. (Connect the AUDIO input terminal for audio input.)

- Depending on specifications of video equipment or HDMI to DVI digital cable, the signal trans-

mission may not work property. (The HDMI specification does not support all connections to video

equipment that has HDMI digital output terminal using HDMI to DVI digital cable.)

- For details on compatibility for connection, see support information on DVI connection provided

by the video equipment manufacturer.

• When you connect video equipment with a 21-pin RGB output (Euro-scart) to the projector, use a

commercially available cable that fits in the projector terminal you want to connect.

• The projector does not support RGBC signals via the Euro-scart.

Download from Www.Somanuals.com. All Manuals Search And Download.

Terminal on

connected equipment

Terminal on the

projector

Equipment

Cable

Audio equipment

ø3.5 mm stereo or mono audio cable

(commercially available)

AUDIO 1

ø3.5 mm

audio output

terminal

RCA audio cable (commercially available)

Cables for a camera or a video game

AUDIO 2 (EIP-2600)

AUDIO (EIP-250)

RCA audio

output

terminal

Audio

output

terminal

Monitor

RGB cable (supplied or commercially

available)

MONITOR OUT

RGB

input

terminal

Amplifier

ø3.5 mm stereo or mono audio cable

(commercially available)

ø3.5 mm

audio input

terminal

AUDIO OUT

ø3.5 mm stereo minijack to RCA audio cable

(commercially available)

RCA audio

input

terminal

is only for EIP-2600.

Note

• Only for EIP-2600:

- When using the ø3.5 mm mono audio cable, the volume level will be half of when using the ø3.5

mm stereo audio cable.

- You can select “Audio 1” or “Audio 2” for “Audio Input” in the “PRJ-ADJ” menu. (See page 46.)

• RGB signals and Component signals can be output to the monitor.

Download from Www.Somanuals.com. All Manuals Search And Download.

Controlling the Projector by a Computer

When the RS-232C terminal on the projector is connected to a computer with a DIN-D-sub RS-

232C adaptor and an RS-232C serial control cable (cross type, commercially available), the com-

puter can be used to control the projector and check the status of the projector. See page 57 for

details.

When connecting to a computer using an RS-232C serial control cable and a DIN-

D-sub RS-232C adaptor

To RS-232C terminal

DIN-D-sub RS-232C

adaptor (supplied)

Computer

To RS-232C terminal

RS-232C serial control cable (cross type, commercially available)

Note

• The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the

owner’s manual of the computer for details.

• See page 56 for connection of an RS-232C serial control cable.

Info

• Do not connect the RS-232C cable to a port other than the RS-232C terminal on the computer. This

may damage your computer or projector.

• Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on.

This may damage your computer.

Connecting the Power Cord

Plug the supplied power cord into the

AC socket on the rear of the projector.

Then plug into AC outlet.

AC socket

Power cord

(supplied)

To AC outlet

Download from Www.Somanuals.com. All Manuals Search And Download.

Turning the Projector On/Off

Info

• When “Auto Restart” is set to “On”:

If the power cord is unplugged from the outlet

or the breaker switch is turned off when the

projector is on, then the projector automati-

cally turns on when the power cord is plugged

into the AC outlet or the breaker switch is

turned on. (See page 45.)

• English is the factory default language. If you

want to change the on-screen display to an-

other language, change the language accord-

ing to the procedure on page 44.

Turning the Projector on

Note that the connections to external equip-

ment and power outlet should be done be-

fore performing the operations written be-

low. (See pages 21 to 24.)

Remove the lens cap and press

STANDBY/ON on the projector or ON

on the remote control.

• The power indicator illuminates red.

• After the lamp indicator illuminates, the projec-

tor is ready to start operation.

Lamp indicator

Power indicator

Note

• About the Lamp Indicator

The lamp indicator illuminates to indicate the

status of the lamp.

STANDBY/ON button

Green: The lamp is on.

Blinking in green: The lamp is warming up.

Red: The lamp is shut down abnormally

or the lamp should be replaced.

• When switching on the projector, a slight flick-

ering of the image may be experienced within

the first minute after the lamp has been illumi-

nated. This is normal operation as the lamp’s

control circuitry is stabilising the lamp output

characteristics. It should not be regarded as

faulty operation.

• If the projector is put into standby mode and

immediately turned on again, the lamp may

take some time to start projection.

STANDBY

button

•

When System Lock is set, the keycode input box

appears. To cancel the keycode setting, input

the keycode that you have already set. See page

46 for details.

ON button

On-screen display (confirmation message)

Turning the Power off (Putting

the Projector into Standby Mode)

Press STANDBY/ONon the projector or

STANDBY on the remote control, then

press that button again while the confir-

mation message is displayed, to put the

projector into standby mode.

• The projector cannot be turned on while cool-

ing.

Info

• Direct Power Off function:

You can unplug the power cord from the AC out-

let even if the cooling fan is still running.

Download from Www.Somanuals.com. All Manuals Search And Download.

Image Projection

Setup Guide screen

About the Setup Guide

After turning on the projector, the Setup

Guide screen appears to assist you with

projector setup.

Guidance items

1 FOCUS

2 HEIGHT ADJUST

3 ZOOM

Press ENTER to exit the Setup Guide

screen.

Note

• The Setup Guide screen automatically high-

lights the items in the following order:

1 FOCUS 2 HEIGHT ADJUST

4 ENTER

3 ZOOM

STANDBY/ON

button

However, you can adjust the focus, height

(angle), or zoom regardless of the highlighted

item.

• If you do not want to display the Setup Guide

for the next time, set “Menu” - “SCR - ADJ” -

“Setup Guide” to “Off”. (See page 44.)

ENTER button

Zoom ring

Adjusting the Projected Image

1 Adjusting the Focus

You can adjust the focus with the focus

ring on the projector.

Rotate the focus ring to adjust the fo-

cus while watching the projected image.

2 Adjusting the Picture Size

You can adjust the picture size using

the zoom ring on the projector.

Focus ring

Rotate the zoom ring to enlarge or

shrink the picture size.

Download from Www.Somanuals.com. All Manuals Search And Download.

3 Adjusting the Height

The height of the projector can be ad-

justed using the adjustment feet at the

front and rear of the projector.

When the screen is above the projec-

tor, the projection image can be made

higher by adjusting the projector.

Lift the projector to adjust its

height while lifting the HEIGHT

ADJUST lever.

HEIGHT

ADJUST lever

Remove your hands from the

HEIGHT ADJUST lever of the pro-

jector after its height has been

finely adjusted.

• The angle of projection is adjustable up

to 9 degrees from the surface on which

the projector is placed.

Make small

adjustments.

Use the rear adjustment foot to

make the projector level.

• The projector is adjustable 2 degrees

from the standard position.

Note

• When adjusting the height of the projector,

trapezoidal distortion occurs. Follow the pro-

cedures in Keystone Correction to correct the

distortion. (See pages 28 and 43.)

Rear adjustment foot

Info

• Do not apply too much pressure on the pro-

jector when the front adjustment foot comes

out.

• When lowering the projector, be careful not to

get your fingers caught in the area between

the adjustment foot and the projector.

•

Hold the projector firmly while lifting or carrying.

• Do not hold by the lens area.

Download from Www.Somanuals.com. All Manuals Search And Download.

Image Projection (Continued)

Correcting Trapezoidal

Distortion

Adjustment buttons

(P/R/O/Q)

When the image is projected either from

the top or from the bottom towards the

screen at an angle, the image becomes

distorted trapezoidally.The function for

correcting trapezoidal distortion is

called Keystone Correction.

Note

RETURN button

• The Keystone Correction can be adjusted up

to an angle of approximately 40 (EIP-2600)/

20 (EIP-250) degrees and the screen can

also be set up to an angle of approximately

40 (EIP-2600)/ 20 (EIP-250) degrees (when

the resize mode is set to “NORMAL” (see page

30)).

KEYSTONE button

On-screen display

(Keystone Correction mode)

KEYSTONE

ADJUST

END

Press KEYSTONE to enter the

Keystone Correction mode.

• You can also display the on-screen dis-

play of the Keystone Correction mode

with KEYSTONE on the projector.

Shrinks upper side.

(Move the slide bar in the + direction.)

Press P/Q or O/R to adjust the

Keystone Correction.

• You can also adjust the Keystone Cor-

rection using the adjustment buttons on

the projector.

Shrinks lower side.

(Move the slide bar in the - direction.)

Note

• To return to the default setting, press RETURN

while the on-screen display of the Keystone

Correction mode is on the screen.

Info

Press KEYSTONE.

• The on-screen display of the Keystone

Correction mode will disappear.

• You can also use KEYSTONE on the pro-

jector.

• While adjusting the image using Keystone

Correction, straight lines and the edges of the

image may appear jagged.

Download from Www.Somanuals.com. All Manuals Search And Download.

COMPUTER,

DVI (EIP-2600 only),

S-VIDEO, VIDEO buttons

Switching the Input Mode

Select the appropriate input mode for

the connected equipment.

AV MUTE button

Press COMPUTER, DVI (EIP-2600

only), S-VIDEO or VIDEO on the remote

control to select the input mode.

• When you press INPUT on the projector or DVI

on the remote control (EIP-2600 only), the INPUT

list appears.

VOL +/– (Volume)

buttons

Press P/R to switch the INPUT mode.

Adjusting the Volume

Press VOL +/– on the remote control or

–O/Q+on the projector to adjust the vol-

ume.

Note

• Pressing VOL–/–O will lower the volume.

• Pressing VOL+/Q+ will raise the volume.

• When the projector is connected to external

equipment, the volume level of the external equip-

ment changes in accordance with the volume

level of the projector. Set the projector’s volume

to the lowest level when turning the projector on/

off or when changing the input signal.

On-screen display

• When you do not want to output the sound from

the projector’s speaker while the projector is con-

nected to external equipment, set “Speaker” in

“PRJ-ADJ” menu to “Off”. (See page 45.)

Displaying the Black Screen

and Turning off the Sound

Temporarily

Press AV MUTE on the remote control

to temporarily display a black screen

and turn off the sound.

On-screen display

Note

• Pressing AV MUTE again will turn the pro-

jected image back on.

Download from Www.Somanuals.com. All Manuals Search And Download.

Image Projection (Continued)

Resize Mode

This function allows you to modify or customize the resize mode to enhance the input image. De-

pending on the input signal, you can choose a desired image.

Press RESIZE.

• See page 43 for setting on menu screen.

RESIZE

button

COMPUTER

Main resolution

SVGA (800 x 600)

XGA (1024 x 768)

SXGA (1280 x 1024)

1280 x 800

NORMAL

FULL

DOT BY DOT

BORDER

STRETCH

800 x 600

1024 x 768

768 x 576

EIP-2600

EIP-250

1024 x 576

968 x 768

1280 x 1024

1280 x 800

720 x 576

922 x 576

1024 x 768

1024 x 640

SVGA (800 x 600)

XGA (1024 x 768)

SXGA (1280 x 1024)

1280 x 800

600 x 450

720 x 450

BORDER

800 x 600

1024 x 768

1280 x 1024

1280 x 800

800 x 450

750 x 600

800 x 500

800 x 600

Input signal

For 4:3 screen

FULL

For 16:9 screen

Computer

Image type

NORMAL

DOT BY DOT

STRETCH

EIP-2600

EIP-250

Resolution Resolution

lower than lower than

XGA

SVGA

XGA

SVGA

*^1,*³

4:3 aspect ratio

Resolution

higher

than

Resolution

higher than

XGA

SVGA

SXGA (1280 × 1024)

5:4 aspect ratio

16:9 aspect ratio

1280 × 720

1360 × 768

1366 × 768

1280 × 768

1280 × 800

16:10 aspect ratio

: Cutout area on which images cannot be projected

: Area where the signals are off screen

The Image Shift function can be used for these images.

Same as NORMAL mode.

For EIP-250 model, “Border” cannot be selected with certain resolution selections in which the horizontal part of aspect ratio becomes smaller than

4:3 (such as 1280 × 1024, among others).

Download from Www.Somanuals.com. All Manuals Search And Download.

VIDEO

VIDEO/DTV

Input signal

For 4:3 screen

AREA ZOOM

For 16:9 screen

BORDER STRETCH

Video/DTV

Image type

NORMAL

V-STRETCH

4:3 aspect ratio

480I, 480P,

576I, 576P,

NTSC, PAL,

SECAM

Squeeze

Letter box

720P, 1035I,

1080I, 1080P

16:9 aspect ratio

540P

(4:3 aspect ratio in 16:9)

: Cutout area on which images cannot be projected

: Area on which the image is not included in the original signals

The Image Shift function can be used for these images.

Same as NORMAL mode.

About Copyrights

• When using the RESIZE function to select an image size with a different aspect ratio to

a TV program or video image, the image will look different from its original appearance.

Keep this in mind while choosing an image size.

• The use of the Resize or Keystone Correction function to compress or stretch the image

for commercial purposes/public displays in a café, hotel, etc. may be an infringement of

Download from Www.Somanuals.com. All Manuals Search And Download.

Operating with the Remote Control

BREAK TIMER button

FREEZE button

Displaying the Pointer

MAGNIFY buttons

Press POINTER and press P/R/

O/Qon the remote control to move

POINTER button

SPOT button

the pointer.

• Press EFFECT to change the pointer icon

(5 types).

Star

Finger1

Finger2

Heart

Underline

Adjustment buttons

(P/R/O/Q)

EFFECT button

PICTURE MODE button

Press POINTER again.

• The pointer will disappear.

ECO+QUIET button

AUTO SYNC button

Using the Spot Function

Displaying and Setting the

Break Timer

Press SPOT and press P/R/O/Q

on the remote control to move the

spot area.

• Press EFFECT to change the spot area

size (3 types).

Press BREAK TIMER.

• The timer starts to count down from 5

minutes.

1/9

1/25

1/8

On-screen display

Press SPOT again.

• The spot area will disappear.

Press P /R /O /Q to adjust the

length of the break time.

• Increases with P or Q

5 minutes s 6 minutes s 60 minutes

• Shortens with O or R

4 minutes s 3 minutes s1 minute

• The break time can be set in units of one

minute (up to 60 minutes).

Switching the Eco+Quiet

Mode

Press ECO+QUIET to switch the

Canceling the break timer display function

Eco+Quiet mode between on and off.

• When the Eco+Quiet Mode is set to “ON”, the

sound of the cooling fan will turn down, the

power consumption will decrease, and the lamp

life will extend.

Press BREAK TIMER.

Note

• Break Timer does not function while the pro-

jector is operating the “Auto Sync”, “FREEZE”

or “AV MUTE” functions.

Note

• Refer to “Lamp Setting” on page 42 for de-

tails of the Eco+Quiet mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

Auto Sync

(Auto Sync Adjustment)

Displaying an Enlarged

Portion of an Image

Graphs, tables and other portions of

projected images can be enlarged.This

is helpful when providing more detailed

explanations.

Auto Sync function works when detect-

ing input signal after the projector turns

on.

Press AUTO SYNC to manually adjust

with Auto Sync function.

Press

MAGNIFY on the remote

control.

Note

• Enlarges the image.

• When the optimum image cannot be achieved

with Auto Sync adjustment, use the help menu

for manual adjustments. (See page 48.)

• Pressing

or reduces the projected image.

MAGNIFY enlarges

Note

Press

Freezing a Moving Image

Press

• You can change the location of the en-

larged image using P, R, O and Q.

Press FREEZE.

• The projected image is frozen.

Press FREEZE again to return to

Press RETURN on the remote con-

trol to cancel the operation.

• The magnification then returns to ×1.

the moving image from the cur-

rently connected device.

Note

• The selectable magnifications differ de-

pending on the input signal.

• In the following cases, the image will

return to the normal size (×1).

Selecting the Picture Mode

- When switching the INPUT mode.

- When RETURN has been pressed.

- When the input signal is changed.

- When the input signal resolution and

refresh rate (vertical frequency)

change.

- When the Resize mode is changed.

- When the Picture mode is changed.

- When the Progressive mode is changed.

You can select the appropriate picture

mode for the projected image, such as

movie or video game.

Press PICTURE MODE.

• When pressing PICTURE MODE, the picture

mode changes in the following order:

STANDARD PRESENTATION

MOVIE GAME sRGB

Note

• See page 40 for details on the picture mode.

* “sRGB” is displayed only when RGB signal is

input.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operating with the Remote Control (Continued)

Using the Remote Control as the Wireless Computer Mouse

When connecting the projector and the computer with a USB cable, you can use

the remote control as the computer mouse.

Connecting with a USB cable

Computer

To USB terminal

USB cable

(commercially available)

PAGE UP/

PAGE DOWN buttons

The mouse pointer can be oper-

ated in the following way after it

MOUSE/Adjustment

buttons ('/"/\/|)

is connected.

■ When moving the cursor

Press MOUSE/Adjustment buttons (P/R/O/Q).

■ When left-clicking

Press L-CLICK.

■ When right-clicking

R-CLICK button

L-CLICK button

Press R-CLICK.

■

When your computer supports only a

one-click mouse (such as Macintosh)

Press L-CLICK or R-CLICK.

L-CLICK and R-CLICK have common function.

■ When using [Page Up] or [Page Down]

Same as the [Page Up] and [Page Down] keys on a computer keyboard.

Press PAGE UP or PAGE DOWN.

Note

• This function only works with the Microsoft^®Windows^®OS and Mac OS^®. However, this function

does not work with the following operation systems that do not support USB.

• Versions earlier than Windows^®95

• Versions earlier than Windows^®NT4.0

• Versions earlier than Mac OS^®8.5

• You cannot use this function when displaying the menu screen.

• Confirm that the computer recognizes the USB connection.

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu Items

The following shows the items that can be set in the projector.

Main menu

Sub menu

“Picture” menu

Standard

Presentation

Movie

Picture

Picture Mode

Page 40

PAGE 1

Game

sRGB*1

Picture

SCR - ADJ

PRJ - ADJ

Standard

Help

Picture Mode

Contrast

Bright

Color

Contrast

Bright

Color

Tint

-30

+30

+30 *2

Tint

Sharp

Red

+30

Sharp

Red

+30 *2

+30

Blue

+30

Page 41

SEL./ADJ.

ENTER

END

PAGE 2

CLR Temp

-1

Picture

SCR - ADJ

PRJ - ADJ

Help

Page 41

BrilliantColor™

Picture Mode

Standard

Page 41

C.M.S. Setting [On/Off]

CLR Temp

BrilliantColor^TM

C.M.S. Setting

C.M.S.

Progressive

DNR

Page 41

3D Progressive

C.M.S.

Off

Page 41

Progressive

Lamp Setting

Reset

Bright

2D Progressive

3D Progressive

Film Mode

Page 42

DNR

Off

Level 1

Level 2

SEL./ADJ.

ENTER

END

Page 42

Lamp Setting

Bright

Eco + Quiet

Page 42

Reset

“C.M.S.”

C. M. S.

C. M. S. - Hue

C. M. S. - Saturation

C. M. S. - Value

Reset

C.M.S.-Hue

-30

+30

Page 41

C.M.S.-Saturation

Page 41

C.M.S.-Value

Page 41

Reset

SEL./ADJ.

Return

ENTER

END

*¹Items when inputting RGB signal through

COMPUTER or DVI (EIP-2600 only).

*²Items when inputting component signal through

COMPUTER or DVI (EIP-2600 only), or when

selecting S-VIDEO or VIDEO.

*³On model EIP-250, this item is “Bright Boost”.

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu Items (Continued)

“Screen adjustment (SCR-ADJ)” menu

Main menu

SCR - ADJ

Sub menu

Picture

Resize

SCR - ADJ

PRJ - ADJ

Normal

Help

Resize

Normal

Full

Area Zoom

V-Stretch

Border

Image Shift

Keystone

Page 43

Dot By Dot

Area Zoom

V-Stretch

Border

Image Shift

Stretch

-96 +96 *3

-75 +75 *4

OSD Display

Closed Caption

Background

Setup Guide

PRJ Mode

VIDEO/

S-VIDEO

Stretch

Page 43

CC1

Logo

COMPUTER/

DTV

Keystone

-80 +80

-40 +40

Front

English

Page 43

OSD Display [On/Off]

Language

Page 43

SEL./ADJ.

ENTER

END

Off

Closed Caption

CC1

CC2

Page 44

*³Adjustment range for EIP-2600.

*⁴Adjustment range for EIP-250.

Logo

Blue

None

Background

Page 44

Setup Guide [On/Off]

Page 44

PRJ Mode

Front

Ceiling + Front

Rear

Ceiling + Rear

Page 44

English

Language

Deutsch

Español

Nederlands

Français

Italiano

Page 44

Svenska

Português

polski

Magyar

Türkçe

“Projector adjustment (PRJ-ADJ)” menu

Main menu

PRJ - ADJ

Sub menu

Picture

SCR - ADJ

PRJ - ADJ

Help

Auto Sync [On/Off]

Auto Sync

Auto Power Off

Auto Restart

STANDBY Mode

System Sound

Speaker

Page 45

Auto Power Off [On/Off]

Standard

Page 45

Auto Restart [On/Off]

Page 45

Audio Input

RS-232C

Audio 1

9600bps

Normal

Disable

STANDBY Mode

Standard

Eco

Fan Mode

Page 45

System Sound [On/Off]

System Lock

Lamp Timer(Life)

min 100%

Page 45

Speaker [On/Off]

SEL./ADJ.

ENTER

END

Page 45

*⁵This item is available for EIP-2600 only.

Audio Input

Audio 1

Audio 2

Page 46

RS-232C

9600bps

115200bps

Page 46

Fan Mode

Normal

High

Page 46

System Lock

[Enable/Disable]

Page 46

Lamp Timer(Life)

Page 47

Download from Www.Somanuals.com. All Manuals Search And Download.

“Help” menu

The items you can set with the “Help”

Picture

SCR - ADJ

PRJ - ADJ

Help

“Help” menu n Page 48

• Vertical stripes or flickering image appear

Auto Sync

There is no picture or audio

Vertical stripes or flickering image appear

Data image is not centered

Color is faded or poor

Clock

Phase

Picture is dark

• Data image is not centered

Auto Sync

The image is distorted

Reset all adjustments to default settings

H-Pos

V-Pos

• Color is faded or poor

COMPUTER/COMPONENT or DVI (EIP-2600

only) input

SEL.

ENTER

END

Signal type: Auto/RGB/Component

S-VIDEO or VIDEO input

Video System: Auto/PAL/SECAM/

NTSC3.58/NTSC4.43/

PAL-M/PAL-N/PAL-60

DVI (Digital) input (EIP-2600 only)

Dynamic range: Auto/Standard/Enhanced

* The selectable items vary depending on the in-

put signal and the selected input mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the Menu Screen

ENTER button

Adjustment buttons (P/R/O/Q)

MENU/HELP button

ENTER button

Adjustment buttons

(P/R/O/Q)

RETURN button

• Press RETURN to return

to the previous screen

when the menu is

displayed.

MENU/HELP button

Menu Selections (Adjustments)

Example: Adjusting “Bright”.

• This operation can also be performed by using the buttons on the projector.

Example: “Picture” screen menu for

Press MENU/HELP.

COMPUTER (RGB) input

(EIP-2600)

• The “Picture” menu screen for the se-

lected input mode is displayed.

Menu item

Press Q or O and select“Picture”

to adjust.

Picture

SCR - ADJ

PRJ - ADJ

Standard

Help

Picture Mode

Contrast

Bright

Red

Blue

CLR Temp

BrilliantColor^TM

C.M.S. Setting

C.M.S.

DNR

Off

Lamp Setting

Reset

Bright

SEL./ADJ.

ENTER

END

Download from Www.Somanuals.com. All Manuals Search And Download.

Press P or R and select “Bright”

to adjust.

• The selected item is highlighted.

Picture

SCR - ADJ

PRJ - ADJ

Standard

Help

Picture Mode

Contrast

Bright

Red

Blue

CLR Temp

BrilliantColor^TM

C.M.S. Setting

C.M.S.

DNR

Off

Lamp Setting

Reset

Bright

SEL./ADJ.

Single ADJ

END

Help

Items to be adjusted

Picture

Resize

SCR - ADJ

PRJ - ADJ

Border

Image Shift

Keystone

To adjust the projected

image while watching it

Press ENTER.

• The selected item (e.g. “Bright”) is dis-

played by itself at the bottom of the

screen.

• When pressing P or R, the following item

(“Red” after “Bright”) will be displayed.

The item displayed by itself

Picture

Bright

SEL./ADJ.

Rtn. Menu

END

Note

• Press ENTER again to return to the pre-

vious screen.

Press O or Q to adjust the item

selected.

Picture

SCR - ADJ

PRJ - ADJ

Standard

Help

Picture Mode

Contrast

Bright

• The adjustment is stored.

1 5

Red

Blue

CLR Temp

BrilliantColor^TM

C.M.S. Setting

C.M.S.

DNR

Lamp Setting

Reset

Off

Bright

Press MENU/HELP.

• The menu screen will disappear.

SEL./ADJ.

Single ADJ

END

Note

• Menu buttons do not function while the projector is operating the “Auto Sync”, “Break Timer”,

“FREEZE”, or “AV MUTE” functions.

Download from Www.Somanuals.com. All Manuals Search And Download.

Picture Adjustment (“Picture” Menu)

Menu operation n Page 38

Q PAGE1

Q PAGE2

Picture

SCR - ADJ

PRJ - ADJ

Standard

Help

Picture

SCR - ADJ

PRJ - ADJ

Standard

Help

Picture Mode

Contrast

Bright

Color

Picture Mode

CLR Temp

BrilliantColor^TM

Tint

C.M.S. Setting

C.M.S.

Progressive

DNR

Sharp

Red

3D Progressive

Off

Blue

Lamp Setting

Reset

Bright

SEL./ADJ.

ENTER

END

SEL./ADJ.

ENTER

END

1 Selecting the Picture Mode

The default settings of each item when selecting Picture Mode

Selectable

items

BrilliantColor^TM(EIP-2600)

Description

CLR Temp

Lamp Setting

Bright Boost (EIP-250)

Standard

For standard image

Bright

Presentation Brightens portions of image for

more enhanced presentations.

Movie

Game

*sRGB

Gives natural tint to the

projected image.

–1

–

Eco + Quiet

Bright

Gives sharpness to the

projected image.

For high fidelity reproduction of

images from a computer.

–

Bright

• “sRGB” is displayed only when RGB signal is input.

• You can set or adjust each item in the “Picture” menu to your preference. Any changes you make are

retained in memory.

Note

•

You can also press PICTURE MODE on the remote control to select the picture mode. (See page 33.)

• *sRGB is an international standard of color reproduction regulated by the IEC (International

Electrotechnical Commission). As the fixed color area has been decided by the IEC, the images are

displayed in a natural tint based on an original image, when “sRGB” is selected.

For additional information about the sRGB function, visit “http://www.srgb.com/”.

You cannot set the items, “Red”, “Blue”, “CLR Temp”, “Bright Boost”, when “sRGB” is selected.

Info

• When “sRGB” is selected, the projected image may become dark, but this does not indicate a

malfunction.

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu operation n Page 38

2 Adjusting the Image

4 Adjusting the Colors

This function adjusts each of the six main colors

that comprise the color wheel, altering their

“Hue”, “Saturation”, or “Value”.

Adjustment

items

O button

Q button

Contrast

For less

contrast.

For more

contrast.

Selectable items

Description

Bright

Color*¹

Tint*¹

For less

brightness.

For less color

intensity.

For making skin For making skin

tones purplish. tones greenish.

For more

brightness.

For more color

intensity.

C.M.S.-Hue

Sets the hue of the main colors.

C.M.S.-Saturation Sets the saturation of the main

colors

C.M.S.-Value

Sets the brightness of the main

colors.

Sharp*¹

For less

For more

Reset

The adjustments of “Hue”,

“Saturation” and “Value” of all

colors are reset to the default

setting.

sharpness.

Red*²

Blue*²

For weaker red. For stronger red.

For weaker blue. For stronger blue.

BrilliantColor™*²*³For making the For making the

Adjusting “Hue”, “Saturation”, or “Value”.

(EIP-2600)

Bright Boost*²

(EIP-250)

effect weaker.

effect stronger.

1Select “On” for “C.M.S. Setting” in the “Picture”

2^mSe^elⁿe^uct^a“ⁿC^d.M^th.S^e.ⁿ” ^pin^reth^sse ^E“P^Nic^Tt^Eu^Rre^.” menu and then

*1 Not displayed in the RGB input mode.

*2 Not adjustable/selectable when selecting “sRGB”.

*3 BrilliantColor™ uses Texas Instruments’

BrilliantColor™ technology. As the BrilliantColor™

level is increased, the image becomes brighter

while the color reproduction is kept at a high level.

3P^pr^re^es^ss^{s E}P^No^Tr^ER^R.to select either “Hue”, “Saturation”, or

4^“S^Ve^ale^luc^et^”th^ae^ndco^thlo^erⁿto^pb^ree^ssad^Ej^Nus^Tt^Eed^R.with P or R and

adjust it with O or Q.

Example of adjusting the “Hue”

Note

Main colors

R (Red)

O button

Q button

• “Red”, “Blue”, “BrilliantColor^TM” (EIP-2600),

“Bright Boost” (EIP-250) and “CLR Temp” can-

not be set when “sRGB” is selected.

• To reset all adjustment items, select “Reset”

and press ENTER.

Closer to magenta Closer to yellow

Y (Yellow)

G (Green)

C (Cyan)

B (Blue)

Closer to red

Closer to green

Closer to cyan

Closer to blue

Closer to magenta

Closer to red

Closer to yellow

Closer to green

Closer to cyan

M (Magenta) Closer to blue

3 Adjusting the Color

• When “Saturation” is selected, the selected

color becomes

Temperature

O: lighter. Q: thicker.

• When “Value” is selected, the selected color

becomes

Selectable

Description

items

For lower color temperature for

warmer, reddish incandescent-like

O: darker. Q: brighter.

–1

• To reset the adjustment values of each color

to the default settings, select “Reset” and press

ENTER.

images.

For higher color temperature for

cooler, bluish, fluorescent-like images.

Note

• Values on “CLR Temp” are only for general

standard purposes.

Download from Www.Somanuals.com. All Manuals Search And Download.

Picture Adjustment (“Picture” Menu)

(Continued)

Menu operation n Page 38

5 Progressive

Reducing Image Noise (DNR)

Video digital noise reduction (DNR) provides high

quality images with minimal dot crawl and cross

color noise.

Selectable

items

Description

2D Useful to display fast-moving images

Progressive such as sports.

Selectable

Description

items

Useful to display relatively slow-

Progressive moving images such as drama and

documentary more clearly.

Off

The DNR function is not activated.

Level 1

Level 2

Sets the DNR level for viewing a

clearer picture.

Film Mode Reproduces the image of film source*

clearly. Displays the optimized image of

film transformed with three-two pull down

(NTSC and PAL60Hz) or two-two pull

down (PAL50Hz and SECAM) enhance-

ment to progressive mode images.

Note

Set “DNR” to “Off” in the following cases:

• When the image is blurry.

• When the contours and colors of moving im-

ages drag.

• When TV broadcasts with weak signals are

projected.

* The film source is a digital video recording with the

original encoded as is at 24 frames/second. The

projector can convert this film source to progres-

sive video at 60 frames/second with NTSC and

PAL60Hz or at 50 frames/second with PAL50Hz

and SECAM to play back a high-definition image.

Note

7 Lamp Setting

• In NTSC or PAL60Hz, even if the 3D Progres-

sive mode has been set, the three-two pull

down enhancement will be enabled automati-

cally when the film source has been entered.

• When the image is blurred or noisy, switch to

the optimal mode.

Selectable

Brightness and Power consumption

items

Eco + Quiet EIP-2600

EIP-250

Approx. 70%

Approx. 80%

100%

Bright

Info

Note

• This function is available for 480I and 576I

signals using COMPUTER/COMPONENT or

DVI (EIP-2600 only) input.

• This function is available for all signals with

S-VIDEO and VIDEO input.

• In the Eco + Quiet mode, the fan sound and

power consumption are lower than those in

the Bright mode. (Projection brightness de-

creases as shown in the chart.)

Download from Www.Somanuals.com. All Manuals Search And Download.

Adjusting the Projected Image

(“SCR - ADJ” Menu)

Menu operation n Page 38

Picture

Resize

SCR - ADJ

PRJ - ADJ

Normal

Help

Image Shift

Keystone

OSD Display

Closed Caption

Background

Setup Guide

PRJ Mode

CC1

Logo

Front

English

Language

SEL./ADJ.

ENTER

END

3 Keystone Correction

1 Setting the Resize Mode

When the image is projected either from the top

or from the bottom towards the screen at an angle,

the image becomes distorted trapezoidally. The

function for correcting trapezoidal distortion is

called Keystone Correction.

Note

• For details of the Resize mode, see pages

30 and 31.

• You can also press RESIZE on the remote con-

trol to set the resize mode. (See page 30.)

Select “Keystone” on the “SCR-ADJ”

menu and adjust with the slide bar.

See page 28 for details of Keystone Correction.

2 Adjusting the Image

Q button

O button

Position

You can move the projected image vertically.

Note

• The Keystone Correction can be adjusted up

to an angle of approximately 40 (EIP-2600)/

20 (EIP-250) degrees (when “Resize” is set

to “Normal”).

O button

Q button

• You can also press KEYSTONE on the remote

control or on the projector to adjust Keystone

Correction.

4 Setting the On-screen

Display

Note

• This function only works in some RESIZE

modes. (See pages 30 and 31.)

Selectable

Description

items

Off

All on-screen displays are displayed.

INPUT/VOLUME/AV MUTE/FREEZE/

AUTO SYNC/RESIZE/PICTURE MODE/

ECO+QUIET/MAGNIFY/ “An invalid

button has been pressed.” are not

displayed.

Download from Www.Somanuals.com. All Manuals Search And Download.

Adjusting the Projected Image

(“SCR - ADJ” Menu) (Continued)

Menu operation n Page 38

5 Closed Caption

Selecting the Setup Guide

Selectable items

Description

Info

Displaying the Setup Guide

when turning the projector on.

Not displaying the Setup Guide.

• This function is available for NTSC3.58 and 480I

signals.

• This function does not work when the resize

mode is set to “Border”.

Off

• This function is available in the following cases

only:

8 Reversing/Inverting

Projected Images

Resize mode

Normal

Area Zoom

V-Stretch

Stretch

Keystone Correction

-40 – +40

-12 – +12

Selectable items

Front

Description

Normal image (Projected from

the front of the screen)

Ceiling + Front

Rear

Inverted image (Projected

from the front of the screen

with an inverted projector)

• “Closed Caption” is a system which allows

conversations, narration, and sound effects in

TV programs (Limited regions) and home

videos to be viewed as captions on the screen.

• Not all programs and videos will offer closed

Reversed image (Projected

from the rear of the screen or

with a mirror)

captioning. Please look for the

symbol to

Ceiling + Rear

Reversed and inverted image

(Projected with a mirror)

ensure that captions will be shown.

• Two channels are available: CC1 and CC2.

• The Closed Caption letters of this projector

are displayed in black and white.

See page 19 for details of Projection (PRJ) Mode.

Selectable items

Off

CC1

CC2

Description

Selecting the On-screen

Display Language

—

Closed Caption mode for CH1 data

Closed Caption mode for CH2 data

The projector can switch the on-screen display

language among 17 languages.

Note

English

• Closed Caption may malfunction (white blocks,

strange characters, etc.) if signal conditions are

poor or if there are problems at the broadcast

source. This does not necessarily indicate a

problem with the projector.

• If any button is pressed to call up the on-screen

display while viewing a Closed Caption broadcast,

the closed captions will disappear.

Deutsch

Español

Nederlands

Français

Italiano

Svenska

Português

polski

Magyar

Selecting the Background

Image

Türkçe

Selectable items

Logo

Blue

Description

EIKI logo screen

Blue screen

—

None

Download from Www.Somanuals.com. All Manuals Search And Download.

Adjusting the Projector Function (“PRJ - ADJ” Menu)

Menu operation n Page 38

Picture

SCR - ADJ

PRJ - ADJ

Help

3 Auto Restart Function

Selectable

Description

items

Auto Sync

Auto Power Off

Auto Restart

STANDBY Mode

System Sound

Speaker

Standard

If the power cord is unplugged from the

outlet or the breaker switch is turned off

when the projector is on, then the

Audio Input

RS-232C

Audio 1

9600bps

Normal

Disable

projector automatically turns on when

the power cord is plugged into the AC

outlet or the breaker switch is turned on.

Fan Mode

System Lock

Lamp Timer(Life)

min 100%

Off

The projector does not turn on

automatically when the power cord is

plugged into the AC outlet or the

breaker switch is turned on.

SEL./ADJ.

ENTER

END

Auto Sync (Auto Sync

Adjustment)

4 STANDBY Mode

When set to “Eco”, power consumption is

reduced in standby mode.

Selectable

items

Description

Auto Sync adjustment will occur when

the projector is turned on or when the

input signals are switched, when

connected to a computer.

Selectable

Description

items

Eco

The monitor output and RS-232C

functions are switched off in standby

mode.

Off

Auto Sync adjustment is not automati-

cally performed.

Standard

The monitor output and RS-232C

functions are activated even if the

projector is in standby mode.

Note

• Auto Sync adjustment is also performed by

pressing AUTO SYNC on the remote control.

• The Auto Sync adjustment may take some time

to complete, depending on the image of the

computer connected to the projector.

Setting the Confirmation

Sound (System Sound)

• When the optimum image cannot be achieved

with Auto Sync adjustment, use manual

adjustments. (See page 48.)

Selectable

items

Description

A confirmation sound is made when

the projector turns on/off.

Auto Power Off Function

Off

No confirmation sound is made.

Selectable

items

Description

6 Speaker Setting

Selectable

Description

items

Off

When no input signal is detected for

more than 15 minutes, the projector will

automatically enter standby mode.

The Auto Power Off function will be

disabled.

The audio signal is output from the

internal speaker.

Off

The audio signal is not output from the

internal speaker.

Note

• When the Auto Power Off function is set to

“On”, 5 minutes before the projector enters

standby mode, the message “Enter STANDBY

mode in X min.” will appear on the screen to

indicate the remaining minutes.

Download from Www.Somanuals.com. All Manuals Search And Download.

Adjusting the Projector Function (“PRJ - ADJ” Menu)

(Continued)

Menu operation n Page 38

a Setting/Changing the keycode

Audio Input (EIP-2600 only)

Monitor Output

Select “System Lock”, then press

ENTER or Q.

This function allows you to select an appropri-

ate combination of audio input terminals for each

input mode.

Selectable

Description

items

Select “Next”, then press ENTER.

• The screen for entering the keycode

appears.

Audio 1

The AUDIO 1 input terminal is used as

an audio input terminal.

Audio 2

The AUDIO 2 input terminal is used as

an audio input terminal.

Press the 4 buttons on the remote

control or on the projector to enter

the preset keycode in “Old Code”.

Selecting the Transmission

Speed (RS-232C)

•

When setting the keycode for the first time,

press R on the projector for four times.

PRJ - ADJ

Make sure that both the projector and computer

are set for the same baud rate.

Setting the System Lock

– – – –

Old Code

New Code

Reconfirm

Selectable

Description

items

9600bps

Transmission speed is slow.

Note

115200bps Transmission speed is rapid.

• If you input a wrong keycode, the cursor

returns to the first point of the “Old Code”.

• The preset keycode is 4 R buttons on

the projector. When you press the R but-

ton four times, the keycord input screen

disappears.

9 Fan Mode Setting

This function changes the fan rotation speed.

Selectable

Description

items

Press the 4 buttons on the remote

control or on the projector to enter

the new keycode in “New Code”.

Normal

High

Suitable for normal environments.

Select this when using the projector at

altitudes of approximately 1,500

meters (4,900 feet) or more.

Note

When “Fan Mode” is set to “High”, the fan rotation

speeds up, and the fan noise becomes louder.

• You cannot use the following buttons for

keycode: STANDBY/ON, ON, STANDBY,

ENTER

L-CLICK, R-CLICK/RETURN

0 System Lock Function

and MENU/HELP

•

System lock function recognizes each

button on the remote control or on the

projector as an individual button, even if

they share the same button name. If you

used the buttons on the projector in set-

ting your keycode, the keycode cannot be

canceled with the remote control.

This function prevents unauthorized use of the

projector. Once this function is activated, users

must enter the correct keycode each time the

projector is turned on. We suggest you record

the keycode in a safe place where only au-

thorized users have access.

Info

PRJ - ADJ

Setting the System Lock

•

If you lose or forget your keycode, contact

your nearest EIKI Authorized Dealer or Service

Center. Even if the product warranty is valid,

the keycode reset will incur a charge.

Old Code

* * * *

– – – –

New Code

Reconfirm

Download from Www.Somanuals.com. All Manuals Search And Download.

Enter the same keycode in “Re-

confirm”.

Keylock Function

Locking the Operation

Buttons on the Projector

Use this function to lock the operation buttons

on the projector.

Note

To cancel the keycode that you have already

set

• Press R on the projector for four times in steps

4 and 5 above.

When the System Lock is set

• When System Lock is set, the keycode input

screen appears after the power is turned on.

When it appears, enter the right keycode to

start projection.

a Locking the Operation Buttons

Hold down ENTER on the projector for about 5

seconds while the projector is being turned on.

On-screen display

Input screen for keycode

• The keylock function does not affect the opera-

tion with the remote control buttons.

• You cannot use the keylock function while the

projector is warming up.

– – – –

System Lock

a Taking the Keylock off

Hold down ENTER on the projector for about 5

seconds.

Checking the Lamp Life

Status

On-screen display

You can confirm the cumulative lamp usage time

and the remaining lamp life (percentage).

• When the projector is in standby mode, you can

release the keylock by holding down ENTER

and STANDBY/ON on the projector simulta-

neously for about 5 seconds.

Lamp usage condition

Remaining lamp life

“Life”

100%

Operated exclusively

with Lamp Setting set to 4,000

“Eco +Quiet”

Approx.

200 hours

Info

hours

Operated exclusively

Approx.

100 hours

• Keylock cannot be set while the projector is:

displaying the “Setup Guide” or “Menu”

screens, in standby mode, warming up, chang-

ing input signals, operating “Auto Sync” func-

tion, in “FREEZE” mode or on the “System

Lock” screen during warming up.

with Lamp Setting set to 2,000

“Bright”

hours

Note

• It is recommended that the lamp be changed

when the remaining lamp life becomes 5%.

• The lamp life may vary depending on the us-

age condition.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting with the “Help” Menu

This function advises you to solve the problems during usage.

Utilizing the “Help” Menu

Functions

ENTER button

Adjustment buttons

(P/R/O/Q)

Example: When image flickering appears

Operation to solve image flickering when pro-

jecting the computer RGB signal.

MENU/HELP

button

Press MENU/HELP.

Press O or Q to select“Help”, then

Select “Initiate “Auto Sync” Ad-

press ENTER.

justments”, then press ENTER.

If the image is not improved, se-

lect “Adjust horizontal noise”,

then press ENTER.

Press P or R to select “Vertical

stripes or flickering image ap-

pears” on Help menu, then press

ENTER.

Press O or Q to adjust.

Picture

SCR - ADJ

PRJ - ADJ

Help

Vertical stripes or flickering image appear

There is no picture or audio

Vertical stripes or flickering image appear

Data image is not centered

Color is faded or poor

Phase

SEL./ADJ.

Rtn. Menu

END

Picture is dark

The image is distorted

Note

• You can adjust the items with check marks (✔).

• The items in the “Help” menu change, de-

pending on the input signal or setting that you

have selected.

• If the problem is not solved, refer to

“Troubleshooting” (see pages 63 and 64).

• When selecting “sRGB” in “Picture Mode”, the

item “Color is faded or poor” is not displayed.

This means you cannot change input signal

types.

Reset all adjustments to default settings

SEL.

ENTER

END

Press ENTER.

Help

Vertical stripes or flickering image appear

Initiate “Auto Sync” Adjustments.

If there is no change after performing "Auto Sync"

adjustments, adjust the following items.

Adjust vertical noise

Adjust horizontal noise

Reset the 2 items above

Return

Signal Info

1024ꢀ ꢀ ꢀ ꢀ 768

59.9 Hz

48.3 kHz

SEL.

ENTER

END

Download from Www.Somanuals.com. All Manuals Search And Download.

Maintenance

Cleaning the projector

Cleaning the lens

■ Ensure that you have unplugged the power

cord before cleaning the projector.

■ The cabinet as well as the operation panel is

made of plastic. Avoid using benzene or

thinner, as these can damage the finish on the

cabinet.

■ Use a commercially available blower or lens

cleaning paper (for glasses and camera lenses)

for cleaning the lens. Do not use any liquid type

cleaning agents, as they may wear off the

coating film on the surface of the lens.

■ As the surface of the lens can easily get

damaged, be careful not to scrape or hit the

lens.

■ Do not use volatile agents such as insecticides

on the projector.

Do not attach rubber or plastic items to the

projector for long periods.

The effects of some of the agents in the plastic

may cause damage to the quality or finish of the

projector.

■ Wipe off dirt gently with a soft flannel cloth.

■ When the dirt is hard to remove, soak a cloth in

a mild detergent diluted with water, wring the

cloth well and then wipe the projector.

Strong cleaning detergents may discolor, warp

or damage the coating on the projector. Make

sure to test on a small, inconspicuous area on

the projector before use.

Cleaning the exhaust and intake vents

■ Use a vacuum cleaner to clean dust from the

exhaust vent and the intake vent.

Mild detergent diluted

with water

Info

• If you want to clean the air vents during projec-

tor operation, ensure you press STANDBY/ON

on the projector or STANDBY on the remote

control and put the projector into standby

mode. After the cooling fan has stopped, clean

the vents.

Thinner

Wax

Download from Www.Somanuals.com. All Manuals Search And Download.

Maintenance Indicators

■ The warning lights (power indicator, lamp indicator and temperature warning indicator) on the

projector indicate problems inside the projector.

■ If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate

red, and the projector will enter standby mode. After the projector has entered standby mode,

follow the procedures given below.

Top View

Temperature warning

indicator

Lamp indicator

Power indicator

About the temperature warning indicator

If the temperature inside the projector increases, due to blockage of the air vents, or the setting location,

“

” will illuminate in the lower left corner of the picture. If the temperature keeps on rising, the lamp

will turn off and the temperature warning indicator will blink, the cooling fan will run, and then the projec-

tor will enter standby mode. After “

” appears, ensure you perform the measures described on

page 51.

About the lamp indicator

■ When the remaining lamp life becomes 5% or less, (yellow) and “Change The Lamp” will be

displayed on the screen. When the percentage becomes 0%, it will change to (red), the lamp will

automatically turn off and then the projector will automatically enter standby mode. At this time, the

lamp indicator will illuminate in red.

■ If you try to turn on the projector a fourth time without replacing the lamp, the projector will

not turn on.

Indicators on the Projector

Power indicator

Green on

Red on

Normal (Standby)

Normal (Power on)

Green blinks Abnormal (See page 51.)

Red blinks

Green on

Normal (Cooling)

Normal

Lamp indicator

Green blinks The lamp is warming up.

Red on

The lamp is shut down abnormally or requires to be

changed. (See page 51.)

Temperature warning Off

indicator

Normal

Red on

The internal temperature is abnormally high. (See page 51.)

Download from Www.Somanuals.com. All Manuals Search And Download.

Maintenance indicator

Problem

Cause

Possible Solution

Normal

Abnormal

Tempera-

ture

warning

indicator

The internal

temperature is

abnormally

high.

•

Blocked air intake

• Relocate the projector to

an area with proper

ventilation. (See page 8.)

Off

Red on

(Standby)

•

Cooling fan

breakdown

Internal circuit

failure

• Take the projector to your

nearest EIKI Authorized

Dealer or Service Center

for repair.

•

Clogged air intake

Lamp

indicator

The lamp does

not illuminate.

The lamp is shut

down abnormally.

• Disconnect the power cord

from the AC outlet, and

then connect it again.

Green on

(Green

blinks

Red on

when the

lamp is

warming

up or

turning

off.)

Time to change

the lamp.

•

Remaining lamp life • Carefully replace the lamp.

becomes 5% or

less.

(See page 52.)

• Take the projector to your

nearest EIKI Authorized

Dealer or Service Center

for repair.

The lamp does

not illuminate.

•

Burnt-out lamp

Red on

(Standby)

Lamp circuit failure

• Please exercise care when

replacing the lamp.

• Securely install the cover.

Power

indicator

The power

indicator blinks

in green when

the projector is

on.

•

The lamp unit cover • If the power indicator blinks

Red on/

Green on

Green

blinks

is open.

in green even when the

lamp unit cover are

Red

blinks

(Cooling)

securely installed, contact

your nearest EIKI

Authorized Dealer or

Service Center for advice.

Info

• If the temperature warning indicator illuminates, and the projector enters standby mode, follow the

possible solutions above and then wait until the projector has cooled down completely before plug-

ging in the power cord and turning the power back on. (At least 10 minutes.)

• If the power is turned off for a brief moment due to power outage or some other cause while using

the projector, and the power supply recovers immediately after that, the lamp indicator will illumi-

nate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet,

replace the power cord in the AC outlet and then turn the power on again.

• The cooling fan keeps the internal temperature of the projector constant and this function is con-

trolled automatically. The sound of the cooling fan may change during operation because the fan

speed may change and this is not a malfunction.

Download from Www.Somanuals.com. All Manuals Search And Download.

Regarding the Lamp

Lamp

■ It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes

5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life

(percentage) can be checked with the on-screen display. (See page 47.)

■ Purchase a replacement lamp of type AH-62101 from your place of purchase, nearest EIKI Authorized

Dealer or Service Center.

Hg LAMP CONTAINS MERCURY For State Lamp Disposal

Information

U.S.A. ONLY

www.lamprecycle.org or 1-800-242-3454

Caution Concerning the Lamp

■ This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp

failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface

scratches or deterioration of the lamp due to a lapse of usage time.

The period of time up to failure largely varies depending on the individual lamp and/or the condition

and the frequency of use. It is important to note that failure can often result in the bulb cracking.

■ When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended

that the lamp be replaced with a new one immediately, even if the lamp appears to be operating

normally.

■ Should the lamp break, there is also a possibility that glass particles may spread inside of the

projector. In such a case, it is recommended you contact your nearest EIKI Authorized Dealer or

Service Center to assure safe operation.

■ Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the

lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes

mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case

of exposure to the gas, consult a doctor as soon as possible.

Replacing the Lamp

Caution

• Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may

cause burns or injury.

• Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully

cool before removing the lamp unit.

■ Carefully change the lamp by following the instructions described in this section. * If you wish,

you may have the lamp replaced at your nearest EIKI Authorized Dealer or Service Center.

If the new lamp does not light after replacement, take your projector to the nearest EIKI Authorized

Dealer or Service Center for repair.

Download from Www.Somanuals.com. All Manuals Search And Download.

Removing and Installing

the Lamp Unit

Warning!

• Do not remove the lamp unit from the projec-

tor right after use. The lamp and parts around

the lamp will be very hot and may cause burns

or injury.

Lamp unit

AH-62101

Optional

accessory

STANDBY/ON button

Info

• Do not touch the glass surface of the lamp

unit or the inside of the projector.

• To avoid injury to yourself and damage to the

lamp, make sure you carefully follow the steps

below.

• Do not loosen other screws except for the

lamp unit cover and lamp unit.

AC socket

Press STANDBY/ONon the projec-

tor or STANDBY on the remote

control to put the projector into

standby mode.

User service screw

(for lamp unit cover)

• Wait until the cooling fan stops.

Disconnect the power cord.

• Unplug the power cord from the AC

socket.

• Leave the lamp until it has fully cooled

down (about 1 hour).

Remove the lamp unit cover.

• Turn the projector over. Loosen the user

service screw (1) that secures the lamp

unit cover. Remove the lamp unit cover

(2).

Download from Www.Somanuals.com. All Manuals Search And Download.

Regarding the Lamp (Continued)

Remove the lamp unit.

• Loosen the securing screws from the

lamp unit. Hold the lamp unit and pull it

in the direction of the arrow. At this time,

keep the lamp unit horizontal and do not

tilt it.

Insert the new lamp unit.

• Press the lamp unit firmly into the lamp

unit compartment. Fasten the securing

screws.

Securing screws

Replace the lamp unit cover.

• Align the tab on the lamp unit cover

(1) and place it while pressing the tab

(2) to close it. Then tighten the user ser-

vice screw (3) to secure the lamp unit

cover.

Info

• If the lamp unit and lamp unit cover are

not correctly installed, the power will not

turn on, even if the power cord is con-

nected to the projector.

Resetting the Lamp Timer

Reset the lamp timer after replacing the lamp.

Info

• Make sure to reset the lamp timer only when

replacing the lamp. If you reset the lamp timer

and continue to use the same lamp, this may

cause the lamp to become damaged or ex-

plode.

AC socket

Connect the power cord.

• Plug the power cord into the AC socket

of the projector.

STANDBY/ON

button

Reset the lamp timer.

ENTER button

• While simultaneously holding down

MENU/HELP, ENTER and R on the pro-

jector, press STANDBY/ON on the pro-

jector.

R button

• “LAMP 0000H” is displayed, indicating

that the lamp timer is reset.

MENU/HELP

button

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting Pin Assignments

COMPUTER/COMPONENT input and COMPUTER/COMPONENT output Terminals : mini D-

sub 15 pin female connector

COMPUTER Input/Output

Pin No. Signal

1. Video input (red)

2. Video input (green/sync on green)

3. Video input (blue)

4. Not connected

COMPONENT Input/Output

Pin No. Signal

1. PR (CR)

3. PB (CB)

4. Not connected

5. Not connected

6. Earth (PR)

5. Not connected

6. Earth (red)

7. Earth (green/sync on green)

8. Earth (blue)

7. Earth (Y)

8. Earth (PB)

9. Not connected

10. Not connected

11. Not connected

12. Not connected

13. Not connected

14. Not connected

15. Not connected

10. GND

11. Not connected

12. Bi-directional data

13. Horizontal sync signal: TTL level

14. Vertical sync signal: TTL level

15. Data clock

DVI-I Terminal : 29 pin connector (EIP-2600 only)

• DVI Digital Input

Pin No. Signal

1. T.M.D.S data 2–

Pin No.

Signal

16. Hot plug detection

17. T.M.D.S data 0–

18. T.M.D.S data 0+

19. T.M.D.S data 0 shield

20. Not connected

21. Not connected

22. T.M.D.S clock shield

23. T.M.D.S clock+

24. T.M.D.S clock–

C1. Not connected

C2. Not connected

C3. Not connected

C4. Not connected

C5. Ground

2. T.M.D.S data 2+

3. T.M.D.S data 2 shield

4. Not connected

5. Not connected

6. DDC clock

7. DDC data

8. Not connected

9. T.M.D.S data 1–

10. T.M.D.S data 1+

11. T.M.D.S data 1 shield

12. Not connected

13. Not connected

14. +5V power

8 7

2 1

15. Ground

• DVI Analog RGB Input

Pin No. Signal

• DVI Analog Component Input

Pin No. Signal Pin No.

Pin No.

Signal

1. Not connected

2. Not connected

3. Not connected

4. Not connected

5. Not connected

6. DDC clock

16. Hot plug detection

17. Not connected

18. Not connected

19. Not connected

20. Not connected

21. Not connected

22. Not connected

23. Not connected

24. Not connected

C1. Analog input Red

C2. Analog input Green

(Sync On Green)

1. Not connected

2. Not connected

3. Not connected

4. Not connected

5. Not connected

6. Not connected

7. Not connected

8. Not connected

9. Not connected

10. Not connected

11. Not connected

12. Not connected

13. Not connected

14. Not connected

15. Ground

16. Not connected

17. Not connected

18. Not connected

19. Not connected

20. Not connected

21. Not connected

22. Not connected

23. Not connected

24. Not connected

C1. Analog input Pr/Cr

C2. Analog input Y

C3. Analog input Pb/Cb

C4. Not connected

C5. Ground

7. DDC data

8. Vertical sync

9. Not connected

10. Not connected

11. Not connected

12. Not connected

13. Not connected

C3. Analog input Blue

C4. Horizontal sync

(Composite Sync)

14. +5V power

15. Ground

C5. Ground

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting Pin Assignments (Continued)

RS-232C Terminal : mini DIN 9 pin female connector

Pin No. Signal

Name

I/O

Reference

Not connected

Receive Data

Send Data

Input

Output

Connected to internal circuit

Not connected

Connected to internal circuit

Not connected

Connected to CS in internal circuit

Connected to RS in internal circuit

Not connected

Signal Ground

Request to Send

Clear to Send

RS-232C Terminal : D-sub 9 pin male connector of the DIN-D-sub RS-232C adaptor

Pin No. Signal

Name

I/O

Reference

Not connected

Connected to internal circuit

Not connected

Connected to internal circuit

Not connected

Connected to CS in internal circuit

Connected to RS in internal circuit

Not connected

Receive Data

Send Data

Input

Output

Signal Ground

Request to Send

Clear to Send

RS-232C Cable recommended connection : D-sub 9 pin female connector

Pin No. Signal

Pin No.

Signal

Note

• Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the

controlling device (e.g. computer).

Projector

Pin No.

Computer

Pin No.

USB Terminal : Type B USB connector

Pin No. Signal

Name

VCC

USB–

USB+

USB power

USB data–

USB data+

Signal Ground

Download from Www.Somanuals.com. All Manuals Search And Download.

RS-232C Specifications and Commands

Computer control

A computer can be used to control the projector by connecting an RS-232C serial control

cable (cross type, commercially available) to the projector. (See page 24 for connection.)

Communication conditions

Set the serial port settings of the computer to match that of the table.

Signal format: Conforms to RS-232C standard.

Baud rate*: 9,600 bps / 115,200 bps

Data length: 8 bits

Parity bit: None

Stop bit: 1 bit

Flow control: None

*Set the projector’s baud rate to the same rate as used by the computer.

Basic format

Commands from the computer are sent in the following order: command, parameter, and

return code. After the projector processes the command from the computer, it sends a re-

sponse code to the computer.

Command format

C1 C2 C3 C4 P1 P2 P3 P4

Return code (0DH

)

Command 4-digit

Parameter 4-digit

Response code format

Normal response

Problem response (communication error or incorrect command)

Return code (0DH

)

Return code (0DH

)

Info

• When controlling the projector using RS-232C commands from a computer, wait for at least 30

seconds after the power has been turned on, and then transmit the commands.

• After sending an input selection or picture adjustment command and then receiving an “OK” re-

sponse code, the projector may take some time to process the command. If a second command is

sent while the projector is still processing the first command, you may receive an “ERR” response

code. If this happens, try resending the second command.

• When more than one code is being sent, send each command only after the response code for the

previous command from the projector is verified.

• “POWR????” “TABN _ _ _ 1” “TLPS _ _ _ 1” “TPOW _ _ _ 1” “TLPN _ _ _ 1” “TLTT _ _ _ 1”

“TLTM _ _ _ 1” “TLTL _ _ _ 1” “TNAM _ _ _ 1” “MNRD _ _ _ 1” “PJN0 _ _ _ 1”

- When the projector receives the special commands shown above:

* The on-screen display will not disappear.

* The “Auto Power Off” timer will not be reset.

- The special commands are available for applications that require continuous polling.

Note

• If an underbar (_) appears in the parameter column, enter a space.

• If an asterisk (*) appears in the parameter column, enter a value in the range indicated in brackets

under Control Contents.

*1 For setting the projector name, send the commands in the order of PJN1, PJN2 and PJN3.

*2 This command should be sent only after the “IRGB _ _ _ 2” command is sent and an “OK” response

code is received.

*3 The Lamp Timer Reset command is available only in standby mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

RS-232C Specifications and Commands (Continued)

Commands

Example: When turning on the projector, make the following setting.

Computer

Projector

→

←

RETURN

CONTROL CONTENTS

COMMAND

PARAMETER

Standby mode

(or 30-second startup time)

OK or ERR

Power ON

OK or ERR

Power

Off

Status

Projector Condition

0: Normal

1: Temp High

8: Lamp Life 5% or less

16: Lamp Burn-out

32: Lamp Ignition Failure

1: Temp High

2: Fan Error

4: Cover Open

8: Lamp Life 5% or less

16: Lamp Burn-out

32: Lamp Ignition Failure

64: Temp Abnormally High

0:Off, 4:Lamp Error

Status

0:Off, 1:On, 2:Retry

3:Waiting, 4:Lamp Error

1:On, 2:Cooling

Lamp

Name

0:Standby

Power Status

Quantity

0 – 9999(Integer)

0, 15, 30, 45

0% – 100%(Integer)

EIP2600/EIP250

EIP-2600/EIP-250

OK or ERR

Usage Time(Hour)

Usage Time(Minute)

Life(Percentage)

Model Name Check

Projector Name Setting 1

(First 4 characters) *1

Projector Name Setting 2

(Middle 4 characters) *1

Projector Name Setting 3

(Last 4 characters) *1

Projector Name Check

Computer

OK or ERR

Projector Name

OK or ERR

ERR

Input Change

DVI

DVI-D-Computer select *2

DVI-D-Video select *2

DVI-Analog select *2

S-Video

Video

1: Computer, 2: DVI (EIP-2600 only) or ERR ERR

1: S-Video, 2: Video or ERR ERR

Input RGB Check

Input Video Check

Input Mode Check

Input Check

1: RGB, 2: Video

1: Computer

2: DVI (EIP-2600 only)

3: S-Video

ERR

4: Video

ERR

OK or ERR

Volume

Volume(0 – 60)

Volume up/down(-10 – +10)

-80 – +80 (XGA)/-40 – +40 (SVGA)

Off

Start

Keystone

AV Mute

Freeze

Auto Sync

Resize

Normal

Stretch

Dot By Dot

Full

Border

Area Zoom

V-Stretch

Normal

Stretch

Dot By Dot

Full

Computer

DVI

Border

Area Zoom

V-Stretch

is only for EIP-2600.

Download from Www.Somanuals.com. All Manuals Search And Download.

RETURN

CONTROL CONTENTS

COMMAND

PARAMETER

Standby mode

Power ON

OK or ERR

(or 30-second startup time)

S-Video

Resize

Normal

ERR

Stretch

Border

OK or ERR

Area Zoom

V-Stretch

Normal

Video

Stretch

Border

Area Zoom

V-Stretch

ALL Reset

Computer INPUT

Picture Mode

Standard

Presentation

Movie

Game

sRGB

Contrast

Bright

Red

Blue

Color

Tint

Sharp

CLR Temp

-30 – +30

-1 – +1

BrilliantColor

0 – +2

(EIP-2600)

Bright Boost

(EIP-250)

Progressive

2D Progressive

3D Progressive

Film Mode

Off

Level 1

Level 2

OK or ERR

ERR

DNR

Picture Reset

Signal Type

Auto

RGB

Compontent

Audio 1

Audio 2

Audio Input

DVI INPUT

Picture Mode Standard

Presentation

Movie

Game

sRGB

Contrast

Bright

Red

Blue

Color

Tint

Sharp

CLR Temp

BrilliantColor^TM0 – +2

(EIP-2600)

-30 – +30

-1 – +1

Bright Boost

(EIP-250)

Progressive

2D Progressive

OK or ERR

ERR

3D Progressive

Film Mode

Off

Level 1

Level 2

DNR

Picture Reset

Signal Type

Auto

RGB

Compontent

Audio 1

Audio 2

Audio Input

Dynamic Range Auto

Standard

Enhanced

is only for EIP-2600.

Download from Www.Somanuals.com. All Manuals Search And Download.

RS-232C Specifications and Commands (Continued)

RETURN

CONTROL CONTENTS

COMMAND

PARAMETER

Standby mode

Power ON

OK or ERR

(or 30-second startup time)

Picture Mode

S-Video INPUT

Standard

Presentation

Movie

ERR

OK or ERR

Game

Contrast

Bright

Red

Blue

Color

Tint

Sharp

CLR Temp

-30 – +30

-1 – +1

BrilliantColor

0 – +2

(EIP-2600)

Bright Boost

(EIP-250)

Progressive

2D Progressive

3D Progressive

Film Mode

Off

Level 1

Level 2

OK or ERR

ERR

DNR

Picture Reset

Audio Input

Audio 1

Audio 2

Video INPUT

Picture Mode Standard

Presentation

Movie

Game

Contrast

Bright

Red

Blue

Color

Tint

Sharp

CLR Temp

BrilliantColor^TM0 – +2

(EIP-2600)

-30 – +30

-1 – +1

Bright Boost

(EIP-250)

Progressive

2D Progressive

OK or ERR

ERR

3D Progressive

Film Mode

Off

Level 1

Level 2

DNR

Picture Reset

Audio Input

Audio 1

Audio 2

C.M.S. Setting

C.M.S.

Off

Hue

Red

Yellow

Green

Cyan

Blue

Magenta

Reset

Red

Yellow

Green

Cyan

Saturation

Blue

Magenta

Reset

Red

Yellow

Green

Cyan

Blue

Magenta

Reset

Value

C.M.S. All Reset

is only for EIP-2600.

Download from Www.Somanuals.com. All Manuals Search And Download.

RETURN

CONTROL CONTENTS

COMMAND

PARAMETER

Standby mode

Power ON

OK or ERR

(or 30-second startup time)

ERR

OK or ERR

Clock

Phase

H-position

V-position

Fine Sync Adjustment Reset

Image Shift

OSD Display

-150 – +150

-30 – +30

-150 – +150

-60 – +60

OK or ERR

kHz(***.* or ERR)

Hz(***.* or ERR)

OK or ERR

ERR

-96 – +96 (XGA)/-75 – +75 (SVGA)

Off

CC1

CC2

Auto

PAL

SECAM

NTSC4.43

NTSC3.58

PAL-M

PAL-N

PAL-60

Logo

Blue

None

Bright

Eco + Quiet

Closed Caption

Video System

Background

Lamp Setting

Auto Sync

Off

Standard

Eco

Auto Power Off

Auto Restart

STANDBY Mode

PRJ Mode

Off

Reverse

Invert

Language

English

Deutsch

Español

Nederlands

Français

Italiano

Svenska

Português

polski

Türkçe

Magyer

Off

Horizontal

Vertical

Normal

High

Setup Guide

System Sound

Internal Speaker

RGB Frequency

Check

Fan Mode

Lamp Timer Reset *3

Download from Www.Somanuals.com. All Manuals Search And Download.

Computer Compatibility Chart

Computer

• Multiple signal support

Horizontal Frequency: 15-110 kHz,

Vertical Frequency: 45-85 Hz,

The following is a list of modes that conform to VESA. However, this projector supports other

signals that are not VESA standards.

Pixel Clock: 12-170 MHz

Sync signal: Compatible with TTL level

• Compatible with sync on green signal

Vertical Frequency

(Hz)

* DVI-D

Support

Display

Horizontal Frequency

(kHz)

VESA

Standard

PC/MAC

Resolution

640 × 350

EIP-2600

EIP-250

27.0

31.5

37.5

27.0

31.5

37.9

27.0

31.5

27.0

31.5

37.9

26.2

31.5

34.7

37.9

37.5

43.3

31.4

35.2

37.9

46.6

48.1

46.9

53.7

40.3

48.4

56.5

60.0

68.7

45.0

47.8

49.7

62.8

47.7

47.8

55.0

66.2

67.5

64.0

80.0

64.0

65.3

75.0

34.9

49.7

60.2

✔

640 × 400

720 × 350

720 × 400

Upscale

VGA

✔

Upscale

640 × 480

✔

SVGA

XGA

800 × 600

True

✔

1024 × 768

True

1280 × 720

1280 × 768

1280 × 800

1360 × 768

1366 × 768

✔

WXGA

SXGA

Intelligent

Compression

Intelligent

Compression

1152 × 864

✔

1280 × 1024

SXGA+ 1400 × 1050

UXGA 1600 × 1200

✔

Upscale

MAC 13"

MAC 16"

MAC 19"

VGA

SVGA

XGA

640 × 480

832 × 624

1024 × 768

Upscale

True

Intelligent

Compression

Intelligent

Compression

MAC 21"

SXGA

1152 × 870

68.7

* EIP-2600 only

Note

• When this projector receives 640K350 VESA format VGA signals, “640 × 400” appears on the screen.

• Optimum image quality will be achieved by matching your computer’s output resolution to the resolution

that corresponds to “True” in the “Display” column shown above.

• When “Screen resolution" of the computer is different from the resolution displayed on the projected im-

age, follow the procedures shown below.

–Refer to “Select the resolution” for “Data image is not centered” on the Help menu and select the same

resolution as the resolution in “Screen resolution” of the computer.

–Depending on the computer you are using, the output signal may not be faithful to the “Screen resolution”

adjustment. Check the settings of the computer’s signal output. If the settings cannot be changed, it is

recommended that the resolution be set to the one that corresponds to “True” in the “Display” column.

DTV

Horizontal

Vertical

DVI-D Support

Horizontal

Vertical

DVI-D Support

Signal

Frequency (kHz) Frequency (Hz) (Compatible with HDCP)

480I

480P

540P

576I

576P

720P

15.7

31.5

33.8

15.6

31.3

37.5

720P

1035I

1080I

1080P

45.0

33.8

28.1

33.8

56.3

67.5

✔

* EIP-2600 only

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

Problem

Check

Page

• Projector power cord is not plugged into the wall outlet.

• Power to the external connected devices is off.

• The selected input mode is wrong.

–

• Cables are incorrectly connected to the projector.

• Remote control battery has run out.

21–24

•

External output has not been set when connecting notebook computer. 21

No picture and no sound

or projector does not

start.

• The lamp unit cover is not installed correctly.

53, 54

•

EIP-2600 only: If the connected DVI digital equipment is turned on

before the “DVI-D” input mode is selected on the projector, the image

may not be projected properly or may not be displayed at all. Ensure

that the appropriate input mode has been selected on the projector

before you turn on the connected equipment.

• Cables are incorrectly connected to the projector.

• “Bright” is set to minimum position.

21–24

• Depending on the computer you are using, an image may not be

projected unless the signal output setting of the computer is

switched to the external output. Refer to the computer owner’s

manual for how to switch its signal output settings.

–

Sound is heard but no

picture appears

(or picture is dark).

• Image adjustments are incorrectly set.

• Make adjustments of “Color” and “Tint” in “Picture Mode” and lower

the “BrilliantColor^TM” (EIP-2600)/“Bright Boost” (EIP-250) value.

(Video Input only)

• Video input system is incorrectly set.

Color is faded or poor.

• Adjust the focus.

• The projection distance exceeds the focus range.

–

•

There is fog on the lens. If the projector is carried from a cold room into a

warm room, or if it is suddenly heated, condensation may form on the

surface of the lens and the image will become blurred. Set up the

projector at least one hour before it is to be used. If condensation should

form, remove the power cord from the wall outlet and wait for it to clear.

Picture is blurred;

noise appears.

(Computer Input only)

• Perform “Fine Sync” Adjustments (“Clock” Adjustment)

• Perform “Fine Sync” Adjustments (“Phase” Adjustment)

• Noise may appear depending on the computer.

–

• Cables are incorrectly connected to the projector.

21–24

• Volume is set to minimum.

• When the projector is connected to an external device and the

volume is set to minimum, the sound is not output even if you turn up

the volume of the external device.

Picture appears but no

sound is heard.

• “Speaker” is set to “Off”.

Data image is not

centered.

• Select “Data image is not centered” in the “Help” menu and make the 48

necessary adjustments.

• Depending on the computer you are using, the output resolution

signal may be different from the one you have set. For details, refer to

the owner’s manual of the computer.

–

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting (Continued)

Problem

Check

Page

An unusual sound is

occasionally heard from

the cabinet.

• If the picture is normal, the sound is due to cabinet shrinkage caused

by room temperature changes. This will not affect operation or

performance.

–

Maintenance indicator on • See “Maintenance Indicators”.

the projector illuminates

or blinks in red.

The projector cannot

be turned on or put into

the standby mode

• The keylock is set.

If the keylock is set to “ON”, all the buttons are locked.

using STANDBY/ON on

the projector.

Picture is green on

COMPUTER

(Component)/

• Change the input signal type setting.

40, 48

• When you cannot select an input signal type, select “Color is faded

or poor” in the “Help” menu, after selecting an item other than

“sRGB” in “Picture Mode”, and then select an input signal type.

*DVI (Component).

Picture is pink

(no green) on

COMPUTER (RGB)/

*DVI (RGB).

Picture is too bright and • Image adjustments are incorrectly set.

whitish.

The cooling fan becomes • When temperature inside the projector increases, the cooling fan

8, 9

49, 50, 51

noisy.

runs faster.

The lamp does not light • The lamp indicator is illuminating in red.

up even after the

projector turns on.

Replace the lamp.

50, 53

The lamp suddenly turns

off during projection.

The image sometimes

flickers.

• Cables are incorrectly connected to the projector or the connected

equipment works improperly.

• Select “Vertical stripes or flickering image appear” in the “Help”

menu and make the necessary adjustments.

21–24

• If this happens frequently, replace the lamp.

The lamp needs much • The lamp will eventually need to be changed.

time to turn on.

While the remaining lamp life draws to a close, replace the lamp.

Picture is dark.

The remote control

cannot be used.

• Operate the remote control while pointing it at the projector’s remote

control sensor.

• The remote control may be too far away from the projector.

• If direct sunlight or a strong fluorescent lamp is shining on the

projector’s remote control sensor, place the projector where it will not

be affected by strong light.

• The batteries may be depleted or inserted incorrectly. Make sure the 14

batteries are inserted correctly or insert new ones.

* EIP-2600 only

This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect operation

or interference. If this should happen, unplug the Unit and plug it in again after more than 5 minutes.

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

Model

EIP-2600

EIP-250

0.55" DLP^®Chip

XGA (1024×768)

F 2.5 – 2.6

Display devices

Resolution

SVGA (800×600)

Lens

F number

Zoom

Manual, ×1.15 (f = 20.4 – 23.5 mm)

Focus

Manual

Input terminals

DVI-I (Compatible with HDCP)

RGB/Component (mini D-sub 15 pin)

S-Video (mini DIN 4 pin)

Video (RCA)

×1

–

Audio (ø3.5 mm stereo minijack)

Audio (RCA)

×1

×1 (L/R)

×1

–

Output terminals RGB/Component (mini D-sub 15 pin)

Audio (ø3.5 mm stereo minijack)

×1 (variable audio output)

Control, others

USB (Type B)

×1

RS-232C (mini DIN 9 pin)

×1

Speakers

2 W (Mono)

Projection lamp

Rated voltage

Rated frequency

Input current

230 W

200W

2.9 A

AC 100 – 240 V

50/60 Hz

3.2 A

Power consumption (Standby)

303 W (5.0 W) with AC 100 V 267 W (5.0 W) with AC 100 V

293 W (5.7 W) with AC 240 V 259 W (5.7 W) with AC 240 V

41°F to 95°F (+5°C to +35°C)

Plastic

Operation temperature

Cabinet

10 ⁴¹/64" × 3 ³³/64" × 10 ⁷/16"

(270 × 89 × 265 mm)

Dimensions (main body only) [W × H × D]

6.4 lbs. (2.9 kg)

Weight (approx.)

As a part of policy of continuous improvement, EIKI reserves the right to make design and

specification changes for product improvement without prior notice. The performance specifica-

tion figures indicated are nominal values of production units. There may be some deviations from

these values in individual units.

This EIKI projector uses a DLP^®chip. This very sophisticated panel contains 786,432

(EIP-2600)/480,000 (EIP-250) pixels (micromirrors). As with any high technology electronic

equipment such as large screen TVs, video systems and video cameras, there are certain

acceptable tolerances that the equipment must conform to.

This unit has some inactive pixels within acceptable tolerances which may result in inactive dots

on the picture screen. This will not affect the picture quality or the life expectancy of the unit.

Download from Www.Somanuals.com. All Manuals Search And Download.

Dimensions

Units: inches (mm)

2 ⁶¹/64 (75)

10 ⁴¹/64 (270)

2 ³

/8 (60)

¹³/32 (10)

1 ²⁷/64

(36)

2 ⁶¹/64 (75)

Download from Www.Somanuals.com. All Manuals Search And Download.

Index

3 RCA to mini D-sub 15 pin cable .......................... 22

Lamp unit ................................................................. 53

Language (on-screen display language) ................ 44

L-CLICK/EFFECT button .................................. 32, 34

Lens Cap ................................................................. 11

Accessories ............................................................. 10

AC socket ................................................................ 24

Adjustment buttons ................................................. 38

AREA ZOOM ........................................................... 31

Aspect ratio ............................................................. 30

Audio Input .............................................................. 46

AUDIO 1, 2 terminal ................................................ 23

AUDIO OUT terminal .............................................. 23

Auto Power Off ........................................................ 45

Auto Restart ............................................................ 45

Auto Sync (Auto Sync adjustment) ....... 33, 37, 45, 48

AUTO SYNC button ................................................. 33

AV MUTE button ...................................................... 29

MAGNIFY buttons ................................................... 33

MENU/HELP button .......................................... 38, 48

MONITOR OUT terminal ......................................... 23

MOUSE/Adjustment buttons ............................. 34, 38

NORMAL ........................................................... 30, 31

ON button ................................................................ 25

Optional accessories ............................................... 10

OSD Display ............................................................ 43

PAGE DOWN button................................................ 34

PAGE UP button ...................................................... 34

PDF ............................................................................ 9

Picture Adjustment .................................................. 40

Picture Mode ..................................................... 33, 40

PICTURE MODE button .......................................... 33

POINTER button ..................................................... 32

Power cord ............................................................... 24

Power indicator ........................................................ 50

PRJ - ADJ ................................................................ 45

PRJ Mode .......................................................... 19, 44

Progressive .............................................................. 42

Background ............................................................. 44

Batteries .................................................................. 14

Blue .......................................................................... 41

BORDER ........................................................... 30, 31

BREAK TIMER button ............................................. 32

Bright ....................................................................... 41

Bright Boost ............................................................. 41

BrilliantColor^TM......................................................... 41

Closed Caption ........................................................ 44

CLR Temp (Color Temperature) .............................. 41

C.M.S. ...................................................................... 41

Color ........................................................................ 41

COMPUTER button ................................................. 29

COMPUTER/COMPONENT input terminal ...... 21, 22

Contrast ................................................................... 41

R-CLICK/RETURN button ................................. 34, 38

Rear adjustment foot ............................................... 27

Red .......................................................................... 41

Remote control ........................................................ 13

Remote control sensor ............................................ 15

Replacing the lamp ........................................... 52, 53

Resize ................................................................ 30, 43

RESIZE button ........................................................ 30

RGB cable ............................................................... 21

RS-232C terminal .................................................... 24

DIN-D-sub RS-232C adaptor .................................. 24

DNR ......................................................................... 42

DOT BY DOT ........................................................... 30

DVI button ................................................................ 29

DVI-I input terminal ........................................... 21, 22

ECO+QUIET button ................................................ 32

ENTER button ......................................................... 38

Exhaust vent ...................................................... 11, 49

SCR - ADJ ............................................................... 43

Screen Size and Projection Distance ..................... 20

Setup Guide....................................................... 26, 44

Sharp ....................................................................... 41

Speaker ................................................................... 45

SPOT button ............................................................ 32

STANDBY button ..................................................... 25

STANDBY Mode ...................................................... 45

STANDBY/ON button .............................................. 25

STRETCH .......................................................... 30, 31

Supplied accessories .............................................. 10

S-VIDEO button ....................................................... 29

S-VIDEO terminal .................................................... 22

System Lock ............................................................ 46

System Sound ......................................................... 45

Fan Mode ................................................................. 46

Fine Sync ................................................................. 48

Focus ring ................................................................ 26

FREEZE button ....................................................... 33

Front adjustment foot .............................................. 27

FULL ........................................................................ 30

HEIGHT ADJUST lever ........................................... 27

Help ......................................................................... 48

H-Pos ................................................................. 37, 48

Image shift ............................................................... 43

INPUT modes .......................................................... 29

Intake vent ......................................................... 11, 49

Temperature warning indicator ............................... 50

Tint ........................................................................... 41

Kensington Security Standard connector ............... 12

Keycode ................................................................... 46

Keylock .................................................................... 47

KEYSTONE button .................................................. 28

Keystone Correction .......................................... 28, 43

USB terminal ........................................................... 34

VIDEO button .......................................................... 29

VIDEO terminal ....................................................... 22

VOL (Volume) buttons ............................................. 29

V-Pos ................................................................. 37, 48

V-STRETCH ............................................................ 31

Lamp ........................................................................ 52

Lamp indicator ......................................................... 50

Lamp Setting ........................................................... 42

Lamp Timer (Life) .................................................... 47

Zoom ring ................................................................ 26

Download from Www.Somanuals.com. All Manuals Search And Download.

U.S.A.

EIKI International, Inc.

30251 Esperanza

Rancho Santa Margarita

CA 92688-2132

U.S.A.

Tel : 800-242-3454 (949)-457-0200

Fax: 800-457-3454 (949)-457-7878

E-Mail : [email protected]

Canada

EIKI CANADA - Eiki International, Inc.

P. O. Box 156, 310 First St. - Unit 2,

Midland, ON, L4R 4K8, Canada

Tel : 800-563-3454 (705)-527-4084

Fax: 800-567-4069 (705)-527-4087

E-Mail : [email protected]

Deutschland & Österreich

EIKI Deutschland GmbH

Am Frauwald 12

Eastern Europe

EIKI CZECH spol. s.r.o.

Umelecká 15

65510 Idstein

170 00 Praha 7

Deutschland

Czech Republic

Tel : 06126-9371-0

Fax: 06126-9371-14

E-Mail : [email protected]

Tel : +42 02 20570024

+42 02 20571413

Fax: +42 02 20571411

E-Mail : [email protected]

China

Japan & Worldwide

EIKI (Shanghai) Co.,LTD

1. Dapu Road, Golden Magnolia Plaza

#2109 Shanghai,

EIKI Industrial Company Limited.

4-12 Banzai-Cho, Kita-Ku, Osaka,

530-0028 Japan

200023 China

Tel : +81-6-6311-9479

Tel : 86-21-5396-0088

Fax : 86-21-5396-0318

E-Mail : [email protected]

Fax: +81-6-6311-8486

WorldWide Website http://www.eiki.com

Download from Www.Somanuals.com. All Manuals Search And Download.

Eizo Computer Monitor L685EX User Manual
Euro Pro Carpet Cleaner EP908H User Manual
EverFocus Security Camera EPTZ 100 User Manual
Exergen Thermometer Instant Thermometry User Manual
Fellowes Paper Shredder PS 70 User Manual
Fisher Paykel Range RA610 User Manual
Foster Oven S4000 PL User Manual
Frigidaire Washer 134533800A User Manual
Gaggenau Range EB 270 User Manual
Gemini Industries Stereo Amplifier P 800 User Manual