EIP-1500T
OWNER’S MANUAL
EIKI INDUSTRIAL CO., LTD.
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT
For your assistance in reporting the loss or theft of your
Projector, please record the Serial Number located on
the bottom of the projector and retain this information.
Before recycling the packaging, please ensure that you
have checked the contents of the carton thoroughly
against the list of “Supplied accessories” on page 5.
Model No.: EIP-1500T
Serial No.:
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 10A fuse. Should
the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked
above, which is also indicated on the pin face of the plug, must be used.
or
and of the same rating as
Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the
mains plug and fit an appropriate type.
DANGER:
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of
in a safe manner.
Under no circumstances should the cut-off plug be inserted elsewhere into a 10A socket outlet, as a serious
electric shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:
WARNING:
THIS APPARATUS MUST BE EARTHED.
IMPORTANT:
The wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow : Earth
Blue
Brown
: Neutral
: Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings
identifying the terminals in your plug proceed as follows:
• The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by
the letter E or by the safety earth symbol
or coloured green or green-and-yellow.
• The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured
black.
• The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured
red.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using the projector, please read this owner’s manual carefully.
Introduction
ENGLISH
1. WARRANTY
This is to assure that you immediately receive the full benefit of the parts, service and labor
warranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety notification of inspection, modification, or
recall that EIKI may be required to give under the 1972 Consumer Product Safety Act, PLEASE
READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.
U.S.A. ONLY
WARNING: High brightness light source. Do not stare into the beam of light, or view directly. Be especially
careful that children do not stare directly into the beam of light.
WARNING: To reduce the risk of fire or electric shock, do not expose this product to
rain or moisture.
See bottom of projector.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk or electric shock to
persons.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREW.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The exclamation point within a triangle is
intended to alert the user to the presence of
important operating and maintenance
(servicing) instructions in the literature
accompanying the product.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not
expressly approved by the manufacturer could void the user’s authority to operate this equip-
ment.
U.S.A. ONLY
INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the owner’s manual, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
U.S.A. ONLY
Declaration of Conformity
EIKI PROJECTOR, MODEL EIP-1500T
This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Responsible Party:
EIKI INTERNATIONAL, INC.
30251 Esperanza, Rancho Santa Margarita, CA 92688-2132
TEL: (800) 242-3454
U.S.A. ONLY
WARNING:
The cooling fan in this projector continues to run for about 90 seconds after the projector enters the standby mode.
During normal operation, when putting the projector into standby mode always use the STANDBY-ON button on
the projector or the STANDBY button on the remote control. Ensure the cooling fan has stopped before disconnecting
the power cord.
DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWER CORD.
FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.
PRODUCT DISPOSAL
This projector utilizes tin-lead solder, and a pressurized lamp containing a small amount of mercury. Disposal of
these materials may be regulated due to environmental considerations. For disposal or recycling information,
please contact your local authorities or, if you are located in the United States of America, the Electronic Industries
Caution Concerning Lamp Replacement
See “Replacing the Lamp” on page 56.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
This EIKI projector uses a DMD panel. This very sophisticated panel contains 921,600 pixels micromirrors. As with
any high technology electronic equipment such as large screen TVs, video systems and video cameras, there are
certain acceptable tolerances that the equipment must conform to.
This unit has some inactive pixels within acceptable tolerances which may result in inactive dots on the picture
screen. This will not affect the picture quality or the life expectancy of the unit.
• DLPTM (Digital Light Processing) and DMDTM (Digital Micromirror Device) are trademarks of Texas Instru-
ments, Inc.
• Microsoft® and Windows® are registered trademarks of Microsoft Corporation in the United States and/or
other countries.
• PC/AT is a registered trademark of International Business Machines Corporation in the United States.
• Macintosh® is a registered trademark of Apple Computer, Inc. in the United States and/or other countries.
• All other company or product names are trademarks or registered trademarks of their respective companies.
• Some IC chips in this product include confidential and/or trade secret property belonging to Texas Instru-
ments. Therefore you may not copy, modify, adapt, translate, distribute, reverse engineer, reverse as-
semble or discompile the contents thereof.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Preparing
Introduction
Setup
Contents.......................................................... 4
Accessories .................................................... 5
IMPORTANT SAFEGUARDS .......................... 6
Part Names and Functions............................ 9
Using the Remote Control........................... 13
Usable Range .................................................... 13
Inserting the Batteries ....................................... 13
Setting Up the Projector .............................. 16
Setting Up the Projector .................................... 16
Screen Size and Projection Distance ................ 17
Projecting a Reversed Image ............................ 18
Connections
Connections ................................................. 19
INPUT Terminals and Connectable
Main Equipment .......................................... 19
Samples of Cables for Connection............. 20
Connecting to Video Equipment................. 21
Connecting to a Computer .......................... 25
Controlling the Projector by a Computer... 27
Quick Start
Quick Start .................................................... 14
Using
Gamma Correction Function ............................. 43
Emphasizing the Contrast ................................. 43
Picture Mode Function....................................... 44
Switching the High Brightness/High Contrast
Mode ........................................................... 44
Computer Image Adjustment
Basic Operation
Turning the Projector On/Off....................... 28
Image Projection .......................................... 29
Switching the INPUT Mode ............................... 29
Adjusting the Focus........................................... 30
Adjusting the Projected Image Size .................. 30
Using the Adjustment Feet ................................ 31
Keystone Correction .......................................... 32
Placement of the Projected Image Using the
(“Fine Sync” menu) ................................ 45
Adjusting the Computer Image ......................... 45
Special Modes Setting ...................................... 45
Auto Sync Adjustment ....................................... 46
Checking the Input Signal ................................. 46
Using the “Options” Menu .......................... 47
Checking the Lamp Life Status ......................... 47
Setting On-screen Display................................. 47
Setting the Video System................................... 48
Signal Type Setting ............................................ 48
Selecting a Background Image ......................... 49
Eco Mode .......................................................... 49
Auto Power Off Function .................................... 50
Selecting the Menu Screen Position .................. 50
Selecting the Menu Color .................................. 51
Selecting the On-screen Display
Keystone Correction.................................... 33
Selecting the Picture Mode ............................... 34
Switching the High Brightness / High Contrast
Mode ........................................................... 34
Adjusting the Picture Aspect Ratio .................... 34
Useful Features
Menu Items ................................................... 36
Using the Menu Screen ............................... 38
Menu Selections (Adjustments) ......................... 38
Menu Selections (Settings) ................................ 40
Picture Adjustment (“Picture” menu) ........ 42
Adjusting the Image .......................................... 42
Adjusting the Color Temperature ....................... 42
Language and the Projection Mode...... 52
Selecting the On-screen Display Language ..... 52
Setting the Projection Mode .............................. 52
Reference
RS-232C Specifications and Command
Appendix
Settings ................................................... 60
PC control .......................................................... 60
Communication conditions ................................ 60
Basic format ...................................................... 60
Commands ........................................................ 60
Computer Compatibility Chart .................... 61
Troubleshooting ........................................... 62
Specifications ............................................... 63
Dimensions ................................................... 64
Glossary ........................................................ 65
Index .............................................................. 66
Maintenance ................................................. 53
Maintenance Indicators ............................... 54
Regarding the Lamp .................................... 56
Lamp ................................................................. 56
Caution Concerning the Lamp .......................... 56
Replacing the Lamp .......................................... 56
Removing and Installing the Lamp Unit ............ 57
Resetting the Lamp Timer ................................. 58
Connecting Pin Assignments ..................... 59
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
Supplied accessories
Remote control
Two R-6 batteries
(“AA” size, UM/SUM-3, HP-7 or similar)
Power cord*
(1)
(2)
For Europe, except U.K.
(6' (1.8 m))
For U.S., Canada, etc.
(6' (1.8 m))
QACCVA011WJPZ
QACCDA007WJPZ
*Use the power cord that corresponds to the wall outlet in your country.
QUICK GUIDE
Owner’s manual
(this manual)
Video cable
Lens cap (attached)
QCNWGA001WJZZ
Optional accessory
■ Lamp unit
AH-57201
Marks Used in This Owner’s Manual
Info
..........Indicates safeguards when using the projector.
.......Indicates additional information for setting up and operating the projector.
Note
• In this owner’s manual, the illustration and the screen display are simplified for explanation, and may differ
slightly from actual display.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFEGUARDS
CAUTION: Please read all of these instructions before you operate this product and save these
instructions for later use.
Electrical energy can perform many useful functions. This product has been engineered and manufactured to
assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR
FIRE HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic
rules for its installation, use and servicing.
1. Read Instructions
13. Power-Cord Protection
All the safety and operating instructions should be read before
the product is operated.
Power-supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs,
convenience receptacles, and the point where they exit from
the product.
2. Retain Instructions
The safety and operating instructions should be retained for
future reference.
14. Lightning
3. Heed Warnings
For added protection for this product during a lightning storm,
or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet and disconnect the cable
system. This will prevent damage to the product due to
lightning and power-line surges.
All warnings on the product and in the operating instructions
should be adhered to.
4. Follow Instructions
All operating and use instructions should be followed.
5. Cleaning
15. Overloading
Unplug this product from the wall outlet before cleaning. Do
not use liquid cleaners or aerosol cleaners. Use a damp cloth
for cleaning.
Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or
electric shock.
6. Attachments
16. Object and Liquid Entry
Do not use attachments not recommended by the product
manufacturer as they may cause hazards.
Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
7. Water and Moisture
Do not use this product near water–for example, near a bath
tub, wash bowl, kitchen sink, or laundry tub; in a wet
basement; or near a swimming pool; and the like.
17. Servicing
Do not attempt to service this product yourself as opening or
removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service
personnel.
8. Accessories
Do not place this product on an unstable cart, stand, tripod,
bracket, or table. The product may fall, causing serious injury
to a child or adult, and serious damage to the product. Use
only with a cart, stand, tripod, bracket, or table recommended
by the manufacturer, or sold with the product. Any mounting
of the product should follow the manufacturer’s instructions,
and should use a mounting accessory recommended by the
manufacturer.
18. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing
to qualified service personnel under the following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into
the product.
9. Transportation
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions, as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to normal
operation.
e. If the product has been dropped or damaged in any
way.
f. When the product exhibits a distinct change in
performance, this indicates a need for service.
A product and cart combination should
be moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the product and cart
combination to overturn.
10. Ventilation
Slots and openings in the cabinet are provided for ventilation
to ensure reliable operation of the product and to protect it
from overheating, and these openings must not be blocked
or covered. The openings should never be blocked by placing
the product on a bed, sofa, rug, or other similar surface. This
product should not be placed in a built-in installation such as
a bookcase or rack unless proper ventilation is provided or
the manufacturer’s instructions have been adhered to.
19. Replacement Parts
When replacement parts are required, be sure that the service
technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original
part. Unauthorized substitutions may result in fire, electric
shock, or other hazards.
11. Power Sources
This product should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supply to your home, consult your product
dealer or local power company. For products intended to
operate from battery power, or other sources, refer to the
operating instructions.
20. Safety Check
Upon completion of any service or repairs to this product,
ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
12. Grounding or Polarization
This product is provided with one of the following types of
plugs. If the plug should fail to fit into the power outlet,
please contact your electrician.
21
.
Wall or Ceiling Mounting
This product should be mounted to a wall or ceiling only as
recommended by the manufacturer.
22. Heat
Do not defeat the safety purpose of the plug.
a. Two-wire type (mains) plug.
This product should be situated away from heat sources such
as radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.
b. Three-wire grounding type (mains) plug with a
grounding terminal.
This plug will only fit into a grounding type power
outlet.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Observe that you read the following safeguards when
setting up your projector.
Caution concerning the lamp unit
■ Potential hazard of glass
particles if lamp ruptures.
In case of lamp rupture,
contact your nearest EIKI
Authorized Dealer or
Service Center for a re-
placement.
Warning about placing the projector in
a high position
■ When placing the projector in a high posi-
tion, ensure that it is secured to avoid per-
sonal injury caused by the projector falling
down.
AH-57201
Do not subject the projector to hard im-
pact and/or vibration.
See “Replacing the Lamp” on page 56.
■ Protect the lens so as not to hit or damage
the surface of the lens.
Caution concerning the setup of the pro-
jector
■ For minimal servicing and to maintain high
image quality, EIKI recommends that this pro-
jector be installed in an area free from hu-
midity, dust and cigarette smoke. When the
projector is subjected to these environments,
the vents and lens must be cleaned more of-
ten. As long as the projector is regularly
cleaned, use in these environments will not
reduce the overall operation life of the unit.
Internal cleaning should only be performed
by an EIKIAuthorized Dealer or Service Cen-
ter.
Rest your eyes occasionally.
■ Continuously watching the screen for long
hours will cause eye strain. Be sure to occa-
sionally rest your eyes.
Avoid locations with extremes of tem-
perature.
■ The operating temperature of the projector
is from 41°F to 95°F (+5°C to +35°C).
■ The storage temperature of the projector is
from –4°F to 140°F (–20°C to +60°C).
Do not block the exhaust and intake
vents.
Do not set up the projector in places ex-
posed to direct sunlight or bright light.
■ Position the screen so that it is not in direct
sunlight or room light. Light falling directly on
the screen washes out the colors, making
viewing difficult. Close the curtains and dim
the lights when setting up the screen in a
sunny or bright room.
7
■ Allow at least 7 /8 inches (20 cm) of space
between the exhaust vent and the nearest
wall or obstruction.
■ Be sure that the intake vent and the exhaust
vent are not obstructed.
■ If the cooling fan becomes obstructed, a pro-
tection circuit will automatically put the pro-
jector into standby mode to prevent overheat
damage. This does not indicate a malfunc-
tion (See pages 54 and 55.). Remove the pro-
jector power cord from the wall outlet and wait
at least 10 minutes. Place the projector where
the intake and exhaust vents are not blocked,
plug the power cord back in and turn on the
projector. This will return the projector to the
normal operating condition.
The projector may be safely tilted to a
maximum angle of 12 degrees.
■ Placement should be within 12 degrees of
horizontal.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFEGUARDS
Caution regarding usage of the projector
■ When using the projector, be sure not to sub-
ject it to hard impact and/or vibration, as this
can result in damage. Take extra care with the
lens. If you are not to use the projector for a
long time, be sure to unplug the power cord
from the wall outlet, and disconnect any other
cables connected to it.
Info
• The cooling fan regulates the internal tem-
perature, and its performance is automati-
cally controlled. The sound of the fan may
change during projector operation due to
changes in the fan speed. This does not
indicate malfunction.
• Do not unplug the power cord during pro-
jection or cooling fan operation. This can
cause damage due to rise in internal tem-
perature, as the cooling fan also stops.
■ Do not use the projector by holding the lens.
■
When you are not to use the projector for a long
time, or storing the projector, re-attach the lens
cap to the projector (See page 9.).
■ Do not expose the projector to direct sunlight
or place it near heat sources. Doing so may
affect the cabinet color or cause deformation
of the plastic cover.
Other connected equipment
■ When connecting a computer or other audio-
visual equipment to the projector, make the
connections AFTER unplugging the power
cord of the projector from the AC outlet and
turning off the equipment to be connected.
■ Please read the owner’s manuals of the pro-
jector and the equipment to be connected for
instructions on how to make the connections.
Using the projector in other countries
■ The power supply voltage and the shape of
the plug may vary depending on the region
or country you are using the projector in.
When using the projector overseas, ensure
to use an appropriate power cord for the
country you are in.
Temperature monitor function
■
If the projector starts to over-
heat due to setup problems
or blockage of the air vents,
“
” and “
” will illumi-
nate in the lower left corner of the picture. If the
temperature continues to rise, the lamp will turn
off, the temperature warning indicator on the
projector will blink, and after a 90-second cool-
ing-off period the projector will enter the standby
mode. Refer to “Maintenance Indicators” on
page 54 for details.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Numbers in
refer to the main pages in this owner’s manual where the topic is explained.
Projector
Top View
STANDBY-ON button
Turn the power on or put the
projector into standby mode.
10 Power indicator
28
34
10 54 Lamp indicator
10 54
Temperature warning
indicator
RESIZE button
Switch the picture display
(STRETCH, SIDE BAR, etc.).
30 ZOOM-FOCUS button
Adjust the projected image
size or adjust the focus.
ENTER button
Set items selected or
adjusted on the menu.
39
34
UNDO button
Undo an operation or
return to the previous
display.
29 INPUT button
Switch input mode 1, 2, 3, 4,
5 or DIGITAL.
MENU button
Display adjustment and
setting screens.
38
38 Adjustment buttons
('/"/\/|)
Select menu items and other
settings.
Front View
Remote control sensor
13
Front adjustment foot
(on the bottom of
the projector)
31
31
HEIGHT ADJUST button
• Attaching the lens cap
Push the lens cap on until it clicks
into position.
• Removing the lens cap
Pull the lens cap directly outward.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
About the Indicators on the Projector
Power indicator
...
Green on Normal (Standby)
...
Red on Normal (Power on)
Lamp indicator
...
Green on Normal
...
Green blinks The lamp is warming up or shutting down.
...
Red on The lamp has been shut down abnormally or
needs to be changed. (See page 54.)
Temperature warning indicator
...
Off Normal
...
Red on The internal temperature is abnormally high.
(See page 54.)
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Numbers in
refer to the main pages in this owner’s manual where the topic is explained.
Projector (Rear View)
Terminals Refer to “INPUT Terminals and Connectable Main Equipment” on page 19.
INPUT 2 terminal
Component signals.
21
21
INPUT 4 terminal
Connect video
equipment.
24
24
INPUT 1 terminal
Component signals.
INPUT 3 terminal
Connect video
equipment with an
S-video terminal.
Digital input type switch
22 23 25 26
INPUT 5/DIGITAL
terminal
22 23
25 26
RS-232C terminal
Control the projector using a
computer.
27
7
53
Exhaust vent
The speed and pitch of
the cooling fan may
change during operation
in response to internal
temperature changes.
This is normal operation
and does not indicate a
malfunction.
Intake vent
7 53
Remote control sensor
13
11
Kensington Security
Standard connector
Rear adjustment feet
31
AC socket
Connect the supplied
power cord.
28
Using the Kensington Lock
• This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security
System. Refer to the information that came with the system for instructions on how to use it to secure the
projector.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Numbers in
refer to the main pages in this owner’s manual where the topic is explained.
Remote Control
STANDBY button
Put the projector into standby
mode.
28
32
ON button
Turn the power on.
28
38
KEYSTONE button
Enter the Keystone
Correction mode.
MENU button
Display adjustment and setting
screens.
ENTER button
Set items selected or
adjusted on the menu.
39
34
30
38
Adjustment buttons
('/"/\/|)
UNDO button
Undo an operation or return to the
previous display.
30
ZOOM-FOCUS button
Adjust the projected image
size or adjusting the focus.
INPUT 1 button
29
29
INPUT 2 button
29
29
INPUT 3 button
DIGITAL INPUT button
INPUT 4 button
29
46
29
34
INPUT 5 button
AUTO SYNC button
Automatically adjust images when
connected to a computer.
RESIZE button
Switch the picture display
(STRETCH, SIDE BAR, etc.).
RGB/COMP. button
Switch the signal type
(RGB or Component).
48
34
34
44
PICTURE MODE button
Select the picture setting (Memory)
stored in “Picture Mode” on the
“Picture” menu.
IRIS button
Switch “HIGH BRIGHTNESS
MODE” or “HIGH CONTRAST
MODE”.
Note
• All the buttons on the remote control are made of luminous material that is visible in the dark. Visibility will
diminish over time. Exposure to light will recharge the luminous buttons.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Remote Control
Remote control sensor
Front View
30°
Usable Range
The remote control can be used to control the
projector within the ranges shown in the
illustration.
30°
Remote
control
signal
transmitters
23' (7 m)
30°
Note
Remote control
•
The signal from the remote control can be re-
flected off a screen for easy operation. How-
ever, the effective distance of the signal may
differ depending on the screen material.
Rear View
Remote control sensor
30°
When using the remote control:
• Ensure that you do not drop the remote control
or expose it to moisture or high temperature.
• The remote control may malfunction under a
fluorescent lamp. In this case, move the pro-
jector away from the fluorescent lamp.
30°
Remote
control
signal
30°
23' (7 m)
transmitters
Inserting the Batteries
Remote control
1 Pull down the tab on the cover
and remove the cover towards
the direction of the arrow.
2 Insert the included batteries
(two “AA” size).
• Insert the batteries making sure the po-
larities correctly match the
and
marks inside the battery compartment.
3 Insert the lower tab of the cover
into the opening, and lower the
cover until it clicks in place.
Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below.
Caution
• Insert the batteries making sure the polarities correctly match the
and
marks inside the battery compartment.
• Batteries of different types have different properties, therefore do not mix batteries of different types.
• Do not mix new and old batteries.
This may shorten the life of new batteries or may cause old batteries to leak.
• Remove the batteries from the remote control once they have run out, as leaving them in can cause them to leak.
Battery fluid from leaked batteries is harmful to skin, therefore ensure that you first wipe them and then remove them using a
cloth.
• The batteries included with this projector may run down in a short period, depending on how they are kept.
Be sure to replace them as soon as possible with new batteries.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start
This section shows the basic operation. For details, see the page described below for each step.
Setup and Projection
Connection of the projector and the video equipment with an S-video terminal is explained as an
example below.
3, 8 STANDBY-ON button
8 STANDBY button
3 ON button
6 ZOOM-FOCUS button
7 KEYSTONE button
6
Adjustment buttons ('/"/\/|)
6, 7 Adjustment buttons
('/"/\/|)
4 INPUT button
6 ZOOM-FOCUS button
4 INPUT buttons,
DIGITAL INPUT button
6 HEIGHT ADJUST button
1.Place the projector facing a screen
Page 16
2.Connect the projector to the video equipment and plug the
power cord into the AC socket of the projector
Connect the audio output terminal of the video equipment to the audio input
terminal of the audio equipment using an audio cable.
Pages 21-28
3.Remove the lens cap and turn the projector on
On the projector
On the remote control
Page 28
14
Download from Www.Somanuals.com. All Manuals Search And Download.
4.Select the INPUT mode
Select the “INPUT 3” using the INPUT button on the projector or the INPUT 3 button on the remote control.
On the
projector
On the remote
control
" On-screen Display
• When pressing
on the projector, input mode switches in order of :
INPUT 1 INPUT 2 INPUT 3 INPUT 4 INPUT 5 DIGITAL
•
When using the remote control, press
/
/
/
/
/
to switch the INPUT mode.
Page 29
5.Turn the video equipment on and playback
6.Adjust the projector angle, focus and zoom
1 Adjust the focus.
On the projector
3 Adjust the projector angle
using the HEIGHT ADJUST
button.
On the remote control
1Press
.
1Press
.
2Adjust the focus by pressing \ or |.
2Adjust the focus by pressing \ or |.
2 Adjust the projected image size by adjusting zoom.
On the remote control
1Press
On the projector
.
1Press
.
HEIGHT ADJUST
button
2Adjust the zoom by pressing ' or ".
2Adjust the zoom by pressing ' or ".
Pages 30, 31
7.Correct trapezoidal distortion
Correcting trapezoidal distortion using the Keystone Correction
On the remote control
Horizontal
Vertical
Select “H Keystone” Adjust
or “V Keystone”.
Pages 32, 33
8.Turn the Power off
Press the STANDBY-ON button on the projector or the STANDBY button on the remote control, then press
the same button again while the confirmation message is displayed, to put the projector into standby mode.
On the projector
On the remote control
" On-screen Display
• Unplug the power cord from the AC outlet after the cooling fan stops.
Page 28
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up the Projector
Setting Up the Projector
Position the projector perpendicular to the screen to achieve an optimal image.
Note
• The projector lens should be centered in the middle of the screen. If the horizontal line passing through
the lens center is not perpendicular to the screen, the image will be distorted, making viewing difficult.
• For an optimal image, position the screen so that it is not in direct sunlight or room light. Light falling
directly on the screen washes out the colors, making viewing difficult. Close the curtains and dim the lights
when setting up the projector in a sunny or bright room.
Standard Setup (Front Projection)
■ Place the projector at the required distance from the screen according to the desired picture size. (See
page 17.)
Indication of the Projection Image Size and Projection Distance
See “Screen Size and Projection Distance” on page 17 for details.
Example : When using a wide screen (16:9)
Picture Size
200"
174"
×
98"
150"
131"
×
74"
100"
80"
87"
×
49"
70"
Center
×
39"
60"
Projection
Distance
52"
×
29"
5' 1" – 7' 8"
(1.55m – 2.35m)
6' 9" – 10' 4"
(2.08m – 3.15m)
8' 7" – 12' 11"
(2.62m – 3.95m)
12' 11" – 19' 6"
(3.95m – 5.95m)
17' 4" – 26' 0"
(5.29m – 7.95m)
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Screen Size and Projection Distance
The projection screen size varies according to the distance from the lens of the projector to the screen.
Install the projector so that projected images are projected onto the screen at the optimum size by referring
to the table below. Use the values in the table as a reference when installing the projector.
Side View
Screen
H
Lens center
L
When using a wide screen (16:9):
In case of displaying the 16:9 picture on the whole of the 16:9 screen.
Picture (Screen) size
Projection distance [L]
Minimum [L1] Maximum [L2]
5.29 m (17' 4") 7.95 m (26' 0")
3.95 m (12' 11") 5.95 m (19' 6")
2.62 m (8' 7") 3.95 m (12' 11")
2.08 m (6' 9") 3.15 m (10' 4")
1.82 m (5' 11") 2.75 m (9' 0")
1.55 m (5' 1") 2.35 m (7' 8")
1.01 m (3' 3") 1.55 m (5' 1")
Distance from the bottom of the image to
the lens center [H]
χ
Diag. [ ]
Width
Height
200" (508 cm)
150" (381 cm)
100" (254 cm)
80" (203 cm)
70" (178 cm)
60" (152 cm)
40" (102 cm)
443 cm (174")
332 cm (131")
221 cm (87")
177 cm (70")
155 cm (61")
133 cm (52")
89 cm (35")
249 cm (98")
187 cm (74")
125 cm (49")
100 cm (39")
87 cm (34")
75 cm (29")
50 cm (20")
8.3 cm (3 9/32")
6.2 cm (2 29/64")
4.2 cm (1 21/32")
3.3 cm (1 5/16")
2.9 cm (1 5/32")
2.5 cm
1.7 cm
(
(
63/64")
43/64")
χ
:
Picture size (diag.) (in/cm)
The formula for picture size and projection distance
L: Projection distance (m/ft)
[m/cm]
[Feet/inches]
χ
χ
χ
χ
L1: Minimum projection distance (m/ft)
L1 (m) = 0.02671 –0.05334
L1 (ft) = (0.02671 –0.05334) / 0.3048
L2: Maximum projection distance (m/ft)
L2 (m) = 0.03999 –0.05215
L2 (ft) = (0.03999 –0.05215) / 0.3048
χ
χ
H: Distance from the bottom of the image to the lens center (cm/in)
H (cm) = 0.04151
H (in) = 0.04151 / 2.54
When using a normal screen (4:3):
In case of setting the 16:9 picture to the full horizontal width of the 4:3 screen.
Picture (Screen) size
Projection distance [L]
Minimum [L1] Maximum [L2]
4.85 m (15' 10") 7.29 m (23' 11")
3.62 m (11' 10") 5.45 m (17' 10")
2.40 m (7' 10") 3.62 m (11' 10")
1.91 m (6' 3") 2.88 m (9' 5")
1.66 m (5' 5") 2.52 m (8' 3")
1.42 m (4' 7") 2.15 m (7' 0")
0.93 m (3' 0") 1.42 m (4' 7")
Distance from the bottom of the image to
the lens center [H]
χ
Diag. [ ]
Width
Height
200" (508 cm)
150" (381 cm)
100" (254 cm)
80" (203 cm)
70" (178 cm)
60" (152 cm)
40" (102 cm)
406 cm (160")
305 cm (120")
203 cm (80")
163 cm (64")
142 cm (56")
122 cm (48")
81 cm (32")
305 cm (120")
229 cm (90")
152 cm (60")
122 cm (48")
107 cm (42")
91 cm (36")
61 cm (24")
7.62 cm (3")
5.72 cm (2 17/64")
3.81 cm (1 1/2")
3.05 cm (1 13/64")
2.67 cm (1 1/16")
2.29 cm
1.52 cm
(
(
57/64")
39/64")
χ
:
Picture size (diag.) (in/cm)
The formula for picture size and projection distance
L: Projection distance (m/ft)
[m/cm]
[Feet/inches]
χ
χ
χ
χ
L1: Minimum projection distance (m/ft)
L1 (m) = 0.02452 –0.05334
L1 (ft) = (0.02452 –0.05334) / 0.3048
L2: Maximum projection distance (m/ft)
L2 (m) = 0.03671 –0.05215
L2 (ft) = (0.03671 –0.05215) / 0.3048
χ
χ
H: Distance from the bottom of the image to the lens center (cm/in)
H (cm) = 0.03810
H (in) = 0.03810 / 2.54
Note
• There may be an error of 3% in the above values.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up the Projector
Projecting a Reversed Image
Projection from behind the Screen
■ Place a translucent screen between the projector and the audience.
■ Reverse the image by setting “Rear” in the “PRJ Mode” menu. (See page 52.)
Translucent screen
Audience
Projection Using a Mirror
■ Place a mirror (normal flat type) in front of the lens.
■ When the translucent screen is placed between the mirror and audience, set to “Front” in the “PRJ Mode”
menu. (See page 52.)
■ When the mirror is placed on the audience side, set to “Rear” in the “PRJ Mode” menu. (See page 52.)
Set to “Front”
Set to “Rear”
Mirror
Translucent screen
Audience
Audience
Mirror
Info
• When using a mirror, ensure to carefully position both the projector and the mirror so the light does not
shine into the eyes of the audience.
Ceiling-mount Setup
■ It is recommended that you use the optional EIKI ceiling-mount
bracket for this installation.
■ Before mounting the projector, contact your nearest EIKI Autho-
rized Dealer or Service Center to obtain the recommended ceil-
ing-mount bracket (sold separately).
■ Invert the image by setting “Ceiling + Front” in “PRJ Mode”. See
page 52 for use of this function.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
INPUT Terminals and Connectable Main Equipment
INPUT 1, 2 terminal
INPUT 5/DIGITAL terminal
Connecting video equipment with
component output terminal (DVD
player, DTV decoder, DVD recorder
with hard disc, etc.). (See pages 22,
23.)
Connecting video equipment with
component output terminal (DVD
player, DTV decoder, DVD recorder
with hard disc, etc.). (See page 21.)
INPUT 3 terminal
Connecting video equipment with S-video
output terminal (VCR, DVD player, etc.).
(See page 24.)
Connecting the computer. (See
pages 25, 26.)
RS-232C terminal
Connecting the computer
to control the projector.
(See page 27.)
INPUT 4 terminal
Connecting video equipment without
S-video output terminal. (See page 24.)
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Samples of Cables for Connection
•For more details of connection and cables, refer to the owner’s manual of the connecting equipment.
•You may need other cables or connectors not listed below.
Terminal on
Terminal on the
projector
Equipment
Cable
connected equipment
Audio-visual
equipment
Component cable (commercially available)
INPUT 1, 2
Component
video output
terminal
Terminal
for using
the
Dedicated cable attached to the connected equipment
INPUT 1, 2
dedicated
cable
DVI cable (commercially available)
RGB cable (commercially available)
INPUT 5/DIGITAL
INPUT 5/DIGITAL
DVI output
terminal
RGB output
terminal
DVI to 15-pin D-sub adaptor
(commercially available)
Computer
Video cable (supplied)
INPUT 4
INPUT 4
Video
output
terminal
Terminal
for using
the
Dedicated cable attached to the connected equipment
dedicated
cable
S-video cable (commercially available)
INPUT 3
INPUT 3
RS-232C
S-video
output
terminal
Terminal
for using
the
dedicated
cable
Dedicated cable attached to the connected equipment
Computer
RS-232C cable (commercially available)
RS-232C
terminal
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Video Equipment
Before connecting, ensure that you have unplugged the power cord of the projector from the
AC outlet and turned off the devices to be connected. After making all connections, turn on
the projector and then the other devices.
Ensure that you have read the owner’s manuals of the devices to be connected before making
connections.
When connecting the component video equipment to the component input terminal on the
projector (INPUT 1 or INPUT 2)
Analog component
output terminal
DVD Player,etc.
INPUT 1 or INPUT 2 terminal
1
2
Component cable
(commercially available)
Note
• When you connect video equipment with a 21-pin RGB output (Euro-scart) to the projector, use a com-
mercially available cable that fits in the projector terminal you want to connect.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Video Equipment
When connecting the video equipment with RGB output terminal (INPUT 5)
• Before connecting the cable, switch the digital input type switch to “VIDEO”.
1
Switch to “VIDEO”
DVD Player,etc.
INPUT 5 terminal
RGB output terminal
2
RGB cable
(commercially available)
4
DVI to 15-pin D-sub adaptor
(commercially available)
3
Note
• For this connection, select “RGB” for “Signal Type” on the OSD menu or press
(See page 48.)
on the remote control.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
When connecting the video equipment with DVI output terminal (DIGITAL INPUT)
• Before connecting the cable, switch the digital input type switch to “VIDEO”.
1
Switch to “VIDEO”
DVD Player,etc.
DIGITAL terminal
DVI output terminal
2
3
DVI cable
(commercially available)
Note
• Select DIGITAL mode when connecting to video equipment with the digital output terminal. (See page
29.)
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Video Equipment
When connecting video equipment with S-video output terminal (INPUT 3)
DVD Player,etc.
S-video output terminal
INPUT 3 terminal
2
1
S-video cable
(commercially available)
When connecting video equipment with video output terminal (INPUT 4)
Supplied
accessory
Video cable
DVD Player,etc.
Video output terminal
INPUT 4 terminal
2
1
Video cable
(supplied)
Note
• When you connect video equipment with a 21-pin RGB output (Euro-scart) to the projector, use a com-
mercially available cable that fits in the projector terminal you want to connect.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a Computer
When connecting a computer, ensure that it is the last device to be turned on after all the
connections are made.
Connecting to a computer (INPUT 5)
• Before connecting the cable, switch the digital input type switch to “PC”.
Computer
1
Switch to “PC”
INPUT 5 terminal
RGB output terminal
2
RGB cable (commercially available)
4
DVI to 15-pin D-sub adaptor
(commercially available)
3
Note
•
•
Refer to “Computer Compatibility Chart” on page 61 for a list of computer signals compatible with the projector. Use
with computer signals other than those listed may cause some of the functions not to work.
When connecting the projector to a computer in this way, select “RGB” for “Signal Type” on the OSD menu or press
on the remote control. (See page 48.)
•
•
A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest EIKI Autho-
rized Dealer or Service Center.
Depending on the computer you are using, an image may not be projected unless the signal output setting of the
computer is switched to the external output. Refer to the owner’s manual of the computer for switching the computer
signal output settings.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a Computer
When connecting a computer, ensure that it is the last device to be turned on after all the
connections are made.
Connecting to a computer with DIGITAL RGB output Terminal (DIGITAL)
• Before connecting the cable, switch the digital input type switch to “PC”.
Computer
1
Switch to “PC”
INPUT 5 terminal
DVI output terminal
2
DVI cable
(commercially available)
3
Note
• Select DIGITAL mode when connecting to digital output terminal of the computer. (See page 29.)
• Before switching “Digital input type switch” and connecting, ensure to unplug the power cord of the pro-
jector from the AC outlet and turn off the computer to be connected. After making all connections, turn on
the projector and then the computer.
“Plug and Play” function
■ This projector is compatible with VESA-standard DDC 1/DDC 2B. The projector and a VESA DDC com-
patible computer will communicate their setting requirements, allowing for quick and easy setup.
■ Before using the “Plug and Play” function, be sure to turn on the projector first and the connected
computer last.
Note
• The DDC “Plug and Play” function of this projector operates only when used in conjunction with a VESA
DDC compatible computer.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling the Projector by a Computer
When the RS-232C terminal on the projector is connected to a computer, the computer can be used to control
the projector and check the status of the projector.
When connecting to a computer using an RS-232C serial control cable
Computer
RS-232C terminal
RS-232C terminal
1
2
RS-232C serial control cable (cross type, commercially available)
Note
• The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the
owner’s manual of the computer for details.
• See “RS-232C Specifications and Command Settings” on page 60 for details.
Info
• Do not connect the RS-232C cable to a port other than the RS-232C terminal on the computer. This may
damage your computer or projector.
• Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on. This
may damage your computer.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning the Projector On/Off
Supplied
accessory
Power cord
Connecting the Power Cord
Plug the supplied power cord into the
AC socket.
Turning the Projector On
Before performing the steps in this section,
connect any equipment that you use with the
projector. (See pages 19-27.)
Info
Remove the lens cap and press
on
• English is the factory preset language. If you want to
change the on-screen display to another language,
change the language according to the procedure on
page 52.
the projector or on the remote control.
• The power indicator illuminates red.
• After the lamp indicator illuminates, the projec-
tor is ready to start operation.
STANDBY-ON button
Power indicator
Note
Lamp
indicator
• The lamp indicator illuminates or blinks, in-
dicating the status of the lamp.
Green:The lamp is ready.
Blinking green: The lamp is warming up
or shutting down.
Red:The lamp is shut down abnormally or
the lamp should be replaced.
•
When switching on the projector, a slight flicker-
ing of the image may be experienced within the
first minute after the lamp has been illuminated.
This is normal operation as the lamp’s control
circuitry is stabilizing the lamp output charac-
teristics. This does not indicate malfunction.
ON button
STANDBY
button
• If the projector is put into standby mode and
immediately turned on again, the lamp may
take some time to illuminate.
Lens cap
Turning the Power Off (Put-
ting the Projector into Standby Mode)
▼On-screen Display
1 Press
on the projector or
on the remote control, then press
that button again while the confir-
mation message is displayed, to
put the projector into standby
mode.
Info
2
Unplug the power cord from theAC
outlet after the cooling fan stops.
•
Do not unplug the power cord during projection or cool-
ing fan operation. The cooling fan in this projector contin-
ues to run for about 90 seconds after the projector enters
the standby mode. This can cause damage due to rise in
internal temperature, as the cooling fan also stops.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection
Switching the INPUT
Mode
Select the appropriate input mode for the con-
nected equipment.
INPUT 1, 2, 3, 4, 5 and
DIGITAL INPUT button
Press
,
,
,
,
or
on
the remote control to select the input
mode.
"On-screen Display of INPUT Mode (Example)
• When pressing
on the projector, input mode
switches in order of :
INPUT 1
DIGITAL
INPUT 2
INPUT 5
INPUT 3
INPUT 4
INPUT 1 mode
Using
Component
Note
INPUT 2 mode
Using
Component
• When no signal is received, “NO SIGNAL”
will be displayed. When a signal that the
projector is not preset to receive is received,
“NOT REG.” will be displayed.
• The INPUT mode is not displayed when
“OSD Display” of the “Options” menu is set
to “ (OFF)”. (See page 47.)
INPUT 3 mode
Using S-Video
About the INPUT mode
INPUT 4 mode
Using Video
INPUT 1
Used for projecting images
(Component) from equipment connected
to INPUT 1 terminal.
INPUT 2
Used for projecting images
INPUT 5 mode
(Component) from equipment connected
to INPUT 2 terminal.
Component
INPUT 3
(S-Video)
Used for projecting images
from equipment connected
to INPUT 3 terminal.
RGB
INPUT 4
(Video)
Used for projecting images
from equipment connected
to INPUT 4 terminal.
• When switching the component and RGB
input mode, press
on the remote
control or select “Signal Type” in the
“Options” menu.
Used for projecting
images from equipment
connected to INPUT 5
terminal.
INPUT 5
(Component/
RGB)
Used for projecting
DIGITAL
DIGITAL mode
images from equipment
with DVI or RGB output
terminal connected to
INPUT 5 terminal.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection
Adjusting the Focus
1 Press
on the remote control.
Adjustment
buttons ('/"/\/|)
2 Press \ or | on the remote con-
trol to adjust the focus.
ZOOM-FOCUS
button
Note
•
You can also adjust the focus by using
and or on the projector.
\
|
Adjusting the Projected Image Size
ZOOM-FOCUS
button
1 Press
on the remote control.
Adjustment buttons
('/"/\/|)
2 Press ' or " on the remote con-
trol to adjust the zoom.
Note
•
You can also adjust the zoom by using
and or on the projector.
'
"
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Adjustment
Feet
The height of the projector can be adjusted
using the adjustment feet at the front and rear
of the projector when the screen is located
higher than the projector, the screen is inclined
or when the installation site is slightly inclined.
Install the projector so that it is as perpen-
dicular to the screen as possible.
Top View
Side View
Lens
center
1 Lift the projector to adjust its
height while pressing the
HEIGHT ADJUST button.
• The projector is adjustable up to approxi-
mately 12 degrees (6 steps).
• When lowering the projector, it may be
difficult to move the front adjustment foot
because the installation surface is diffi-
cult to slide. In this case, pull the pro-
jector back slightly and adjust its height.
Front
adjustment foot
2 Remove your hands from the
HEIGHT ADJUST button of the
projector after its height has
been finely adjusted.
HEIGHT ADJUST button
3 Finely adjust the height and in-
clination by turning the rear ad-
justment feet.
Note
•
When adjusting the projected image position,
trapezoidal distortion occurs. In this case, see
“Keystone Correction” on page 32.
Info
• Do not press the HEIGHT ADJUST button
when the front adjustment foot comes out
without firmly holding the projector.
• Do not hold the lens when lifting or lower-
ing the projector.
• When lowering the projector, be careful not
to get your fingers caught in the area be-
tween the adjustment foot and the projector.
Rear adjustment feet
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection
KEYSTONE
button
Keystone Correction
This function can be used to adjust the Keystone
settings.
Adjustment
buttons ('/"/\/|)
UNDO
button
Note
• When the image is projected from a di-
rection at an angle, the image becomes
distorted trapezoidally. The function for
correcting trapezoidal distortion is called
Keystone Correction.
1 Press
on the remote control
to enter the Keystone Correction
mode.
"On-screen Display (Keystone Correction mode)
2 Press '/"to select “H Keystone”
or “V Keystone”.
Selectable
Description
items
H Keystone Horizontally adjusts the
keystone settings.
Horizontal Keystone Correction
V Keystone Vertically adjusts the keystone
settings.
Reset
Returns to the factory preset
settings.
3 Press \/| to move the mark on
the selected adjustment item to
the desired setting.
Vertical Keystone Correction
Note
• Straight lines and the edges of the dis-
played image may appear jagged,
when adjusting the Keystone setting.
• When adjusting “H Keystone” and “V
Keystone” at the same time, the
values of adjustable angles for each
setting become smaller.
• The adjustable value of the “V Key-
stone” becomes extremely small
when “H Keystone” is made to be the
maximum value.
• Keystone correction is disabled while
the picture mode is set to “SMART
STRETCH”. (See page 35.)
Note
• When adjusting the Keystone setting, the placement
range is changed depending on the input signal
type.
• Keystone correction cannot be applied to On-screen
Display.
• When Keystone correction is applied, the resolution
of image can be deteriorated to some extent.
• Keystone Correction is also returned to the factory
4 Press
.
• The on-screen display of the Keystone
preset settings by pressing
trol.
on the remote con-
Correction mode will disappear.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Align the edge of the screen clos-
est to the projector with the image
by adjusting the zoom and the
adjuster. (See pages 30 and 31.)
Placement of the Projected Image
Using the Keystone Correction
Place the projector at a distance from the screen that
allows images to be projected onto the screen by referring
to “Screen Size and Projection Distance” on page 17.
Align
ZOOM/FOCUS
ZOOM
FOCUS
END
Align
: Screen area
4
Adjust the Keystone function so that the
size of the projected image matches the
screen size. (See page 32.)
Note
• The aspect ratio of the projected image also shifts
slightly when the “H Keystone” and “V Keystone”
functions are adjusted simultaneously.
• If you cannot correct trapezoidal distortion with
Keystone correction, change the placement
position of the projector.
1 Project an image onto the screen.
Adjust the focus until the image on
the screen comes into focus. (See
page 30.)
5 Align the image on the screen by
adjusting the zoom function and
the adjuster.
ZOOM/FOCUS
ZOOM
FOCUS
END
ZOOM/FOCUS
ZOOM
FOCUS
END
2
Change the projection angle moving
the projector or using the adjuster to
properly project images onto the
screen. (See page 31).
6 Adjust the focus so that the projected
image is in focus at the center of the
screen. (See page 30.)
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection
Selecting the Picture Mode
You can select the picture setting (Memory)
directly stored in “Picture Mode” on the
“Picture” menu.
Press
on the remote control.
• Each time the button is pressed while the display
is on, the picture mode changes in order of:
Memory OFF Memory 1
Memory 2
Memory 3
Memory 5
Memory 4
Note
UNDO
button
• This function can also be accessed from the
OSD menu (see page 44).
RESIZE
button
PICTURE MODE
button
Switching the High Bright-
ness / High Contrast Mode
IRIS button
This function controls the quantity of the pro-
jected light and the contrast of the image.
Press
on the remote control.
•
Each time the button is pressed while the display is on,
RESIZE button
UNDO button
the mode is switched between “HIGH BRIGHTNESS
MODE” and “HIGH CONTRAST MODE”.
Note
• This function can also be accessed from the
OSD menu (see page 44).
Adjusting the Picture
Aspect Ratio
This function allows you to modify or
customize the picture display mode to enhance
the input image. Depending on the input signal,
you can choose STRETCH, SIDE BAR, SMART
STRETCH or CINEMA ZOOM image.
Press
on the remote control.
• Each time
is pressed, the picture mode
changes as shown on the next page.
•
To return to the standard image (“STRETCH”), press
while “RESIZE” is displayed on the screen.
• You can also change the picture display mode
by pressing on the projector.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Output screen image
SIDE BAR SMART STRETCH
Input signal
STRETCH
CINEMA ZOOM
4:3 aspect ratio
480
480P
576
I
I
576P
NTSC
PAL
SECAM
Letterbox
Squeeze
16:9 aspect ratio
540P
1080
I
16:9 aspect ratio
720P
16:9 aspect ratio
VGA
SVGA
XGA
4:3 aspect ratio
Note
• “SMART STRETCH” cannot be selected while the Keystone correction (page 32) is being adjusted.
• Keystone correction (page 32) is disabled while the picture mode is set to “SMART STRETCH”.
• 580I/580P is displayed on the screen when signal 576I/576P is input.
• “STRETCH” is fixed when 540P, 720P or 1080I signal is entered.
• “SMART STRETCH” cannot be selected while input signal from a computer (VGA, SVGA or XGA) is
entered.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Items
The following shows the items that can be set in the projector.
“Picture” menu
Main Menu
Sub Menu
Example: Screen for INPUT 1
Picture
Contrast
Bright
Color
Tint
-30
-30
-30
-30
-30
-30
-30
+30
+30
+30
+30
+30
+30
+30
mode
Page 42
*1
*1
*1
Sharp
Red
Blue
Reset
Page 42
5500K
6500K
7500K
8500K
9300K
10500K
0
0
0
0
0
0
10
10
10
10
10
10
CLR Temp
Page 42
Gamma Adj.
Standard
Cinema 1
Cinema 2
Cinema 3
-3
-3
-3
-3
3
3
3
3
Example: Screen for INPUT 5
(RGB) mode
Page 43
Bright Boost [ON/OFF]
Page 43
Picture Mode
Memory 1
Memory 2
Memory 3
Memory 4
Memory 5
Memory OFF
Page 44
IRIS
High Brightness
High Contrast
Page 44
*1: Items when selecting INPUT 1, 2, 3, 4 or when inputting component signal
through INPUT 5
“Fine Sync” menu
Example: Screen for INPUT 5
(RGB) mode
Main Menu
*2
Fine Sync
Clock
Phase
H-Pos
V-Pos
Reset
-30
-15
-30
-30
+30
+15
+30
+30
*2
Page 45
Page 45
Special Modes
Page 45
*2
Auto Sync [ON/OFF]
Page 46
Signal Info
Page 46
*2: Item when inputting RGB signal through INPUT 5
Note
•“Tint” cannot be used with PAL, SECAM, PAL-M, PAL-N or PAL-60.
•“Color”, “Tint”, “Sharp”, “Clock”, “Phase”, “H-Pos”, “V-Pos” and “Auto Sync” cannot be used in the DIGITAL
mode.
•“Fine Sync” menu cannot be displayed in the INPUT 3 and INPUT 4 modes.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
“Options” menu
Example: Screen for INPUT 1
Main Menu
Sub Menu
mode
Options
Lamp Timer (Life)
Page 47
Page 47
OSD Display [ON/OFF]
Page 47
*1
Video System
Page 48
Auto
PAL
NTSC3.58
SECAM
NTSC4.43
PAL-M
PAL-N
PAL-60
*2
RGB
Signal Type
Component
Page 48
Background [Blue/None]
Page 49
Example: Screen for INPUT 4
mode
Eco Mode [Eco/Standard]
Page 49
Auto Power Off [ON/OFF]
Page 50
Menu Position
Center
Upper Right
Lower Right
Upper Left
Lower Left
Page 50
Menu Color [Opaque/Translucent]
Page 51
*1: Item when selecting INPUT 3 or INPUT 4
*2: Item when selecting INPUT 5
“Language” menu
Main Menu
Language
English
Deutsch
Español
Nederlands
Français
Italiano
Page 52
Svenska
Português
“PRJ Mode” menu
Main Menu
PRJ Mode
Front
Ceiling+Front
Rear
Page 52
Ceiling+Rear
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menu Screen
The menu can be operated to achieve two functions, adjustments and settings. (For setting
the menu items, see pages 40 and 41. )
Adjustment
buttons (
'/"/\/|)
ENTER button
Adjustment buttons
('/"/\/|)
MENU button
MENU
button
ENTER
button
UNDO button
UNDO
button
Menu Selections
(Adjustments)
• This operation can also be performed by using the
buttons on the projector.
Example: “Picture” menu screen for
INPUT 1 mode
1 Press
.
• The “Picture” menu screen for the selected
Menu icons
input mode is displayed.
2 Press | or \ to display the other
menu screens.
• The menu icon for the selected menu screen
is highlighted.
Menu icon
Menu screen
Picture
Fine Sync
Options
Language
PRJ Mode
Note
• The “Fine Sync” menu is not available for
selecting INPUT 3 or 4.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Press ' or " to select the item you
want to adjust.
• The selected item is highlighted.
(Example: Selecting “Bright”)
To adjust the projected
image while viewing it
Single
adjustment
item
Press
.
• The selected single adjustment item (e.g.
“Bright”) appears on the lower part of the
screen.
• When pressing ' or ", the next item will
be displayed. (e.g. “Bright” is replaced with
“Color” by pressing ".)
Note
• Press
to return to the previous screen.
4 Press | or \ to adjust the item se-
lected.
• The adjustment is stored.
5 Press
.
• The menu screen will disappear.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menu Screen
The menu can be operated to achieve two functions, adjustments and settings. The “setting”
item is displayed by or on the menu screen. (For adjusting the menu items, see pages 38
and 39.)
Adjustment
buttons (
'/"/\/|)
MENU
button
ENTER
button
UNDO
button
Menu Selections (Settings)
• This operation can also be performed by using the
buttons on the projector.
1 Press
.
Example: “Picture” menu screen for
INPUT 1 mode
• The “Picture” menu screen for the selected
input mode is displayed.
Menu icons
2 Press | or \ to display the other
menu screens.
• The menu icon for the selected menu screen
is highlighted.
Example: “Options” menu screen
Menu icon
Menu screen
Picture
Fine Sync
Options
Language
PRJ Mode
Note
• The “Fine Sync” menu is not available for
selecting INPUT 3 or 4.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Press ' or " to select the item you
want to set, and then press | to dis-
play the sub menu.
• The selected item is highlighted.
(Example: Selecting “Menu Position”)
Note
• Press
screen.
or \ to return to the previous
Sub menu
• For some items, press \ or | to select
the icon using “ ”.
4 Press ' or " to select the setting
of the item displayed in the sub
menu.
5 Press
.
• The selected item is set.
6 Press
.
• The menu screen will disappear.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Adjustment (“Picture” menu)
You can adjust the projector’s picture to your preferences using the “Picture” menu.
Adjusting the Image
Adjusting the Color Temperature
This function allows for selecting the desired
color temperature. With the lower value selected,
the projected image becomes warmer, reddish
and incandescent-like while with the higher
value, the image becomes cooler, bluish and fluo-
rescent-like.
Menu operation
Page 38
Note
• First select “Memory 1-5” or “Memory OFF”
when you want to save the “Picture” menu set-
tings. See page 44 for details.
Menu operation
Page 40
Example: “Picture” menu screen for
INPUT 1 mode
Example: “Picture” menu screen for
INPUT 1 mode
Description of Color Temperature Settings
CLR Temp
Description
5500K The less the value is set to, the warmer,
6500K reddish, incandescent-like the image becomes.
7500K
Description of Adjustment Items
Selectable items
Contrast For less contrast
Press \
Press |
For more contrast
8500K
9300K The more the value is set to, the cooler,
10500K bluish, fluorescent-like the image becomes.
Bright
Color
Tint
For less brightness
For more brightness
For more color intensity
For less color intensity
“CLR Temp” is fine adjusted by following the procedure below.
For making skin tones purplish For making skin tones greenish
Sharp
Red
Blue
For less sharpness
For weaker red
For more sharpness
For stronger red
1 Select “CLR Temp” in the “Picture”
menu on the menu screen and
For weaker blue
For stronger blue
press
.
• A single menu bar of “CLR Temp” is displayed.
Note
• “Color”, “Tint” and “Sharp” do not appear for
RGB input in INPUT 5 mode.
• To reset all adjustment items, select “Reset” on
2 Press ' or " to fine adjust the
color temperature.
the “Picture” menu screen and press
.
• With the lower value selected, the projected
image becomes magenta-tinged. With the
higher value selected, the projected image
becomes green-tinged.
• “Tint” cannot be used with PAL, SECAM, PAL-
M, PAL-N or PAL-60.
• “Color”, “Tint” and “Sharp” cannot be used in
the DIGITAL mode.
• Pressing \ or | changes the value of the
color temperature in the sub menu.
Note
•
Values on “CLR Temp” are only for general standard purposes.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Gamma Correction Function
Emphasizing the Contrast
Gamma is an image quality enhancement function.
Four gamma settings are available to allow for
differences in the brightness of the room.
This function emphasizes the bright portions of
images to obtain a higher contrast image.
Menu operation
Page 40
Menu operation
Page 40
Example: “Picture” menu screen for
INPUT 1 mode
Example: “Picture” menu screen for
INPUT 1 mode
Description of Gamma Modes
Description of Bright Boost settings
Selectable Items
Standard
Description
Standard picture without gamma
correction
Selectable Items
(ON)
Description
For emphasizing the bright portions
of images
Cinema 1
Cinema 2
Cinema 3
Gives greater depth to darker portions
of images.
Brightness is toned down and the
image becomes more balanced.
Brighten the darker portions of images
for easier viewing in a dimly lit room.
(OFF)
For disabling “Bright Boost”
“Gamma Adj.” is fine adjusted by following the
procedure below.
1 Select “Gamma Adj.” in the “Pic-
ture” menu on the menu screen and
press
.
• A single menu bar of “GammaAdj.” is displayed.
2 Press ' or " to fine adjust the
gamma correction.
• With the lower value selected, the projected
image becomes darker. With the higher
value selected, the projected image be-
comes brighter.
• Pressing \ or | changes the value of the
Gamma in the sub menu.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Adjustment (“Picture” menu)
Picture Mode Function
Switching the High Bright-
ness/High Contrast Mode
This function stores all items set in “Picture”. Five
settings can be stored separately in “Memory 1”
to “Memory 5”. Each stored setting is reassigned
to each input mode (INPUT 1 to INPUT 5).
Even when the input mode or signal is changed,
you can easily select optimal settings from the
stored settings.
This function changes the brightness and
contrast of the projected image. It can be
operated using the IRIS button on the remote
control.
Menu operation
Page 40
Example: “Picture” menu screen for
INPUT 1 mode
Menu operation
Page 40
Example: “Picture” menu screen for
INPUT 1 mode
Description of IRIS Settings
Selectable items
High Brightness High brightness is given priority over
high contrast.
High Contrast High contrast is given priority over high
brightness.
Description
Select “Picture Mode” on the “Picture” menu and
the memory location where you want to store the
settings. Then adjust the setting items on the
“Picture” menu.
Picture Mode
Memory
1-5
Description
Settings of all items in “Picture” can be stored
for the respective input modes. The stored
settings (Memory 1 to 5) can be selected in
any input modes.
Memory
OFF
Besides “Memory 1” to “Memory 5”, other
settings on the “Picture” menu can be stored
for each input mode. The settings stored in
“Memory OFF” cannot be applied when
another input mode is selected.
If you want to apply the stored settings on the “Pic-
ture” menu, select input mode and then press
or select “Picture Mode” in the “Picture” menu.
,
If you want to change the stored settings, select
the memory location for those settings and make
settings on the “Picture” menu.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Image Adjustment (“Fine Sync” menu)
You can adjust the computer image, match the computer display mode, and confirm the
input signal using the “Fine Sync” menu.
Adjusting the Computer
Image
Special Modes Setting
Ordinarily, the type of input signal is detected and
the correct resolution mode is automatically se-
lected. However, for some signals, the optimal
resolution mode in “Special Modes” on the “Fine
Sync” menu may need to be selected to match
the computer display mode.
Use the Fine Sync function in case of irregulari-
ties such as vertical stripes or flickering in por-
tions of the screen.
Menu operation
Page 38
Menu operation
Page 40
Example: “Fine Sync” menu screen for
INPUT 5 (RGB) mode
Example: “Fine Sync” menu screen for
INPUT 5 (Component) mode
Description of Adjustment Items
Selectable items
Clock
Phase
Description
Adjusts vertical noise.
Adjusts horizontal noise (similar to
tracking on your VCR).
Note
• If your computer displays patterns which repeat
every other line (horizontal stripes), flickering
may occur which makes the image hard to see.
• When inputting DTV 1080I signal, select the
corresponding type of signal.
H-Pos
V-Pos
Centers the on-screen image by moving
it to the left or right.
Centers the on-screen image by moving
it up or down.
• See “Checking the Input Signal” on the next
page for information on the currently selected
input signal.
Note
• You can automatically adjust the computer im-
age by setting “Auto Sync” on the “Fine Sync”
menu to “
” (ON) or pressing
on the re-
mote control. See page 46.
• “Clock”, “Phase”, “H-Pos” and “V-Pos” cannot be
used in the DIGITAL mode.
• “Clock” and “Phase” cannot be used in the Com-
ponent mode.
• The adjustable area of each item may be
changed according to the input signal.
• To reset all adjustment items, select “Reset” and
press
.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Image Adjustment (“Fine Sync” menu)
Auto Sync Adjustment
Checking the Input Signal
Select whether the image is to be synchronized
automatically when switching the signal with
“ON” or “OFF”.
This function allows you to check the current in-
put signal information.
Menu operation
Page 40
Menu operation
Page 40
Example: “Fine Sync” menu screen for
INPUT 5 (RGB) mode
Example: “Fine Sync” menu screen for
INPUT 5 (RGB) mode
Description of Auto Sync Adjustment
Selectable items
(ON)
Description
Auto Sync adjustment will occur when
the projector is turned on or when the
input signals are switched, when
connected to a computer.
Auto Sync adjustment is not automati-
cally performed.
(OFF)
Note
• Auto Sync adjustment is also performed by
pressing on the remote control.
• The Auto Sync adjustment may take some time
to complete, depending on the image of the
computer connected to the projector.
• When the optimum image cannot be achieved
with Auto Sync adjustment, use manual adjust-
ments. (See page 45.)
• “Auto Sync” cannot be used in the DIGITAL
mode.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the “Options” Menu
You can use the “Options” menu to enhance the usage for the projector.
Checking the Lamp Life
Status
Setting On-screen Display
This function allows you to turn off the on-screen
messages that appear during input select.
You can confirm the cumulative lamp usage time
and the remaining lamp life (percentage).
Menu operation
Page 40
Menu operation
Page 40
Example: “Options” menu screen for
INPUT 1 mode
Example: “Options” menu screen for
INPUT 1 mode
Description of “OSD Display” Settings
Selectable items
Description
Description of Lamp Life
(ON)
All On-screen Displays are displayed.
Lamp usage condition
“Life”
Remaining lamp life
100%
INPUT/AUTO SYNC/ “An invalid button has
been pressed.” are not displayed.
5%
(OFF)
Operated exclusively
Approx.
Approx.
in Eco mode (
Operated exclusively
in Standard mode (
)
3,000 hours 150 hours
Approx. Approx.
2,000 hours 100 hours
)
Note
• It is recommended that the lamp be changed
when the remaining lamp life becomes 5%. (See
page 56.)
• The table above indicates rough estimates in the
case of using only in each mode shown.
• Remaining lamp life changes within the range of
the values shown depending on the frequency at
which “Eco Mode” is switched to “
” (Eco
mode) and “
” (Standard mode). (See page
49.)
• The lamp life may vary depending on the usage
condition.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the “Options” Menu
Setting the Video System
Signal Type Setting
The video input system mode is factory preset
to “Auto”; however, a clear picture from the con-
nected audio-visual equipment may not be re-
ceived, depending on the video signal difference.
In that case, switch the video signal.
This function allows you to select the input sig-
nal type RGB or Component for INPUT 5.
Menu operation
Page 40
Example: “Options” menu screen for
INPUT 5 (RGB) mode
Menu operation
Page 40
Example: “Options” menu screen for
INPUT 4 mode
Description of Signal Type Settings
Selectable items
RGB
Description
Set when RGB signals are received.
Description of Video Systems
Component
Set when Component signals are
received.
Selectable items
Description
When connected to PAL video equip-
ment.
PAL
When connected to NTSC video
equipment.
When connected to SECAM video
equipment.
When reproducing NTSC signals in PAL
video equipment.
NTSC3.58
SECAM
Note
• You can also select “Signal Type” using
on the remote control (only INPUT 5).
NTSC4.43
Note
• The video signal can only be set in INPUT 3,
INPUT 4 mode.
• “Auto” cannot be set for PAL-M and PAL-N in-
put signals. Select “PAL-M” or “PAL-N” in “Video
System” menu for PAL-M and PAL-N input sig-
nals.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting a Background
Image
Eco Mode
Menu operation
Page 40
This function allows you to select the image dis-
played when no signal is being sent to the pro-
jector.
Example: “Options” menu screen for
INPUT 1 mode
Menu operation
Page 40
Example: “Options” menu screen for
INPUT 1 mode
Description of Eco Mode
Power consumption
(When using AC 100V)
Selectable items Brightness
Lamp life
Approx.
3,000 hours
85%
315 W
(Eco mode)
Description of Background Images
Approx.
2,000 hours
Selectable items
Description
360 W
100%
(Standard mode)
(Blue) Blue screen
Black screen
(None)
Note
• When “Eco Mode” is set to “
” (Eco mode), the
power consumption will decrease and the lamp
life will extend. (Projection brightness decreases
15%.)
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the “Options” Menu
Auto Power Off Function
Selecting the Menu Screen
Position
Menu operation
Page 40
This function allows you to select the desired
position of the menu screen.
Example: “Options” menu screen for
INPUT 1 mode
Menu operation
Page 40
Example: “Options” menu screen for
INPUT 1 mode
Description of Auto Power Off
Selectable items
Description
The projector automatically enters the
standby mode when no input signal is
detected for 15 minutes or longer.
The Auto Power Off function will be
disabled.
(ON)
Description of Menu Positions
(OFF)
Selectable items
Center
Description
Displayed on the center of the image.
Displayed on the upper right of the image.
Displayed on the lower right of the image.
Displayed on the upper left of the image.
Displayed on the lower left of the image.
Upper Right
Lower Right
Upper Left
Lower Left
Note
• When theAuto Power Off function is set to “
”
(ON), 5 minutes before the projector enters the
standby mode, the message “Enter STANDBY
mode in X min.” will appear on the screen to
indicate the remaining minutes.
Position of the Menu Screen which Is
Displayed on the Screen
Upper
Left
Upper
Right
Center
Lower
Left
Lower
Right
Menu screen
Screen
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the Menu Color
This function allows you to select the color of
the menu screen.
Menu operation
Page 40
Example: “Options” menu screen for
INPUT 1 mode
Description of Menu Colors
Description
Selectable Items
(Opaque) The menu is displayed
opaquely.
The menu is displayed
(Translucent)
translucently. The part of the
menu on the image becomes
transparent.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the On-screen Display Language and the
Projection Mode
Selecting the On-screen
Display Language
Setting the Projection
Mode
The projector can switch the on-screen display
language among 11 languages: English, German,
Spanish, Dutch, French, Italian, Swedish, Portu-
guese, Chinese, Korean or Japanese.
This projector is equipped with a reverse/invert
image function that allows you to reverse or in-
vert the projected image for various applications.
Menu operation
Page 40
Example: “Language” menu screen for
INPUT 1 mode
Example: “PRJ Mode” menu screen
Description of PRJ Modes
1
Press
on the remote control.
Selectable items
Front
Description
Normal image
• The “Picture” menu will be displayed.
Ceiling + Front Inverted image
Rear
Reversed image
Ceiling + Rear Reversed and inverted image
2 Press \ or | to select the “Lan-
guage” menu icon ( ).
• The “Language” menu will be displayed.
Front
Rear
Ceiling + Front
3
Press ' or " to select the desired
language, and then press
.
• The language you selected will be set as
the on-screen display.
Ceiling + Rear
4 Press
.
• The “Language” menu will disappear.
Note
• This procedure can also be performed by using
the buttons on the projector.
Note
• This function is used for the reversed image and
ceiling-mount setups. (See page 18.)
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Cleaning the projector
■ Ensure that you have unplugged the power cord be-
Cleaning the lens
■ Use a commercially available blower or lens clean-
ing paper (for glasses and camera lenses) for clean-
ing the lens. Do not use any liquid type cleaning
agents, as they may wear off the coating film on the
surface of the lens.
fore cleaning the projector.
■ The cabinet as well as the operation panel is made
of plastic. Avoid using benzene or thinner, as these
can damage the finish on the cabinet.
■ Do not use volatile agents such as insecticides on
the projector.
■ As the surface of the lens can easily get damaged,
be sure not to scrape or hit the lens.
Do not attach rubber or plastic items to the projec-
tor for long periods.
The effects of some of the agents in the plastic may
cause damage to the quality or finish of the projector.
Cleaning
Paper
Cleaning the exhaust and intake vents
■ Use a vacuum cleaner to clean dust from the ex-
haust vent and the intake vent.
Mild detergent
diluted with water
Thinner
Wax
■ Wipe off dirt gently with a soft flannel cloth.
■ When the dirt is hard to remove, soak a cloth in a
mild detergent diluted with water, wring the cloth
well and then wipe the projector.
Info
• If you want to clean the air vents during pro-
Strong cleaning detergents may discolor, warp or
damage the coating on the projector. Make sure to
test on a small, inconspicuous area on the projec-
tor before use.
jector operation, press
on the projector
or on the remote control and put the projec-
tor into standby mode. After the cooling fan has
stopped, unplug the power cord from the AC
socket and clean the vents.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance Indicators
■ The warning lights on the projector indicate problems inside the projector.
■ If a problem occurs, either the temperature indicator or the lamp indicator will illuminate red, and
the projector will enter the standby mode. After the projector has entered the standby mode, follow
the procedures given below.
Maintenance Indicators
Power indicator
Lamp indicator
Temperature warning indicator
About the temperature warning indicator
If the temperature inside the projector increases, due to blockage of the air vents, or the setting location,
“
” will illuminate in the lower left corner of the picture. If the temperature keeps on rising, the lamp will
turn off and the temperature warning indicator will blink, the cooling fan will run for a further 90 seconds, and
then the projector will enter the standby mode. After “
” appears, be sure to perform the measures
described on page 55.
About the lamp indicator
■When the remaining lamp life becomes 5% or less, “ ” (yellow) and “Change The Lamp.” will be
displayed on the screen. When the percentage becomes 0%, it will change to “ ” (red), the lamp will
automatically turn off and then the projector will automatically enter the standby mode. At this time,
the lamp indicator will illuminate in red.
■
If you try to turn on the projector a fourth time without replacing the lamp, the projector will not turn on.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance indicator
Problem
Cause
Possible solution
Normal
Abnormal
• Relocate the projector to an area
with proper ventilation. (See page
7.)
• Blocked air intake
Temperature
warning
indicator
The internal
temperature is
abnormally high.
• Take the projector to your nearest
EIKI Authorized Dealer or Service
Center for repair.
• Clean the exhaust and intake
vents. (See page 53.)
Red on
(Standby)
• Cooling fan break-
down
• Internal circuit failure
• Clogged air intake
Off
• Disconnect the power cord from
the AC outlet, and then connect it
again.
The lamp does
not illuminate.
—
Green on
Green blinks
when the lamp
is warming up
or shutting
Red on
Red on
• Carefully replace the lamp. (See
page 57.)
• Take the projector to your nearest
EIKI Authorized Dealer or Service
Center for repair.
• Please exercise care when
replacing the lamp.
Lamp
indicator
Time to change
the lamp.
• Remaining lamp life
becomes 5% or less.
down.
The lamp does
(Standby) not illuminate.
• Burnt-out lamp
• Lamp circuit failure
Info
• If the temperature warning indicator illuminates and the projector enters the standby mode, check whether
any of the ventilation holes are blocked (page 7) and then try turning the power back on. Wait until the
projector has cooled down completely before plugging in the power cord and turning the power back on.
(At least 10 minutes.)
• If the power is turned off for a brief moment due to power outage or some other cause while using the
projector, and the power supply recovers immediately after that, the lamp indicator will illuminate in red
and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power
cord in the AC outlet and then turn the power on again.
• Do not unplug the power cord after the projector has entered the standby mode and while the cooling fan
is running. The cooling fan runs for about 90 seconds.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Regarding the Lamp
Lamp
■ It is recommended that the lamp (optional: AH-57201) be replaced when the remaining lamp life
becomes 5% or less, or when you notice a significant deterioration in the picture and color quality.
The lamp life (percentage) can be checked with the on-screen display. See page 47.
■ Purchase a replacement lamp of type AH-57201 from your place of purchase, nearest EIKI Autho-
rized Dealer or Service Center.
Caution Concerning the Lamp
■ This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp
failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface
scratches or deterioration of the lamp due to a lapse of usage time.
The period of time up to failure largely varies depending on the individual lamp and/or the condition
and the frequency of use. It is important to note that failure can often result in the bulb cracking.
■ When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended
that the lamp be replaced with a new one immediately, even if the lamp appears to be operating
normally.
■ Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes
mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In
case of exposure to the gas, consult a doctor as soon as possible.
■ Should the lamp break, there is also a possibility that glass particles may spread inside of the
projector. In such a case, it is recommended you contact your nearest EIKI Authorized Dealer or
Service Center to assure safe operation.
Replacing the Lamp
Caution
• Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burn
or injury.
• Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool
before removing the lamp unit.
■ Carefully change the lamp by following the instructions described in this section. *If you wish, you
may have the lamp replaced at your nearest EIKI Authorized Dealer or Service Center.
* If the new lamp does not light after replacement, take your projector to the nearest EIKI Authorized Dealer or
Service Center for repair.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing and Installing the Lamp Unit
Warning!
• During projector operation, the lamp unit is very hot. Do not remove the lamp unit from the projector
right after use. The lamp and parts around the lamp will be very hot and may cause burn or injury.
Info
• Make sure that you remove the lamp unit
Optional
accessory
Lamp unit
AH-57201
by the handle. Do not touch the glass sur-
face of the lamp unit or the inside of the
projector.
• To avoid injury to yourself and damage to
the lamp, be sure to carefully follow the
steps below.
• Do not loosen other screws except for the
lamp unit cover and lamp unit.
STANDBY-ON button
1 Press
on the projector or
on the remote control to put the
projector into standby mode.
• Wait until the cooling fan stops.
2 Disconnect the power cord.
• Unplug the power cord from the AC
socket.
• Leave the lamp until it has fully cooled
down (about 1 hour).
AC socket
3 Remove the lamp unit cover.
• Turn the projector over. Loosen the user
service screw (1) that secures the lamp
unit cover. Hold the tab and slide to-
wards the direction of the arrow to re-
move the lamp unit cover (2).
1
2
Tab
User service screw
(for lamp unit cover)
Tab
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Regarding the Lamp
Handle
4 Remove the lamp unit.
• Loosen the two securing screws from
the lamp unit. Hold the lamp unit by the
handle and pull it in the direction of the
arrow. At this time, keep the lamp unit
horizontal and do not tilt it.
5 Insert the new lamp unit.
• Press the lamp unit firmly into the lamp
unit compartment. Fasten the securing
screws.
Securing screws
6 Replace the lamp unit cover.
• Align the lamp unit cover and slide it to
close. Then tighten the user service
screw to secure the lamp unit cover.
Info
• If the lamp unit and lamp unit cover are not
correctly installed, the power will not turn
on, even if the power cord is connected to
the projector.
User service screw
(for lamp unit cover)
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
Info
• Make sure to reset the lamp timer only
when replacing the lamp. If you reset the
lamp timer and continue to use the same
lamp, this may cause the lamp to become
damaged or explode.
AC socket
STANDBY-ON button
1 Connect the power cord.
• Plug the power cord into the AC socket
of the projector.
ENTER button
2 Reset the lamp timer.
\/
|
buttons
UNDO button
• Press
,
,
, \,
and | on the
projector in order, and then press
on the projector.
INPUT button
• “LAMP 0000H” is displayed on the lower
left of the screen, indicating that the lamp
timer is reset.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Pin Assignments
DVI-I (INPUT 5) port : 29-pin connector
• DVI Digital INPUT
Pin No. Signal
Pin No. Signal
• • • • • • • • •
• • • •
• • • • • • • • •
• • • •
~
16
9
1
2
3
4
5
T.M.D.S data 2–
16
17
18
19
20
21
22
23
24
C1
C2
C3
C4
C5
Hot plug detection
~
1 2
7 8
T.M.D.S data 2+
T.M.D.S data 2 shield
Not connected
Not connected
DDC clock
T.M.D.S data 0–
T.M.D.S data 0+
T.M.D.S data 0 shield
Not connected
Not connected
T.M.D.S clock shield
T.M.D.S clock+
T.M.D.S clock–
Not connected
Not connected
Not connected
Not connected
Ground
C1
C2
C4
6
7
DDC data
C5
C3
8
9
Not connected
T.M.D.S data 1–
T.M.D.S data 1+
T.M.D.S data 1 shield
Not connected
Not connected
+5V power
17
24
10
11
12
13
14
15
• • • •
• • • •
~
18
23
Ground
• DVI Analog RGB Input
• DVI Analog Component Input
Pin No. Signal
Pin No. Signal
Pin No. Signal
Pin No. Signal
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Not connected
16
17
18
19
20
21
22
23
24
C1
C2
C3
C4
C5
Hot plug detection
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Analog input Red
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Not connected
16
17
18
19
20
21
22
23
24
C1
C2
C3
C4
C5
Not connected
Not connected
Not connected
Not connected
Not connected
DDC clock
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Ground
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Analog input PR/CR
Analog input Y
Analog input PB/CB
Not connected
Ground
DDC data
Vertical sync
Not connected
Not connected
Not connected
Not connected
Not connected
+5V power
Analog input Green
Analog input Blue
Horizontal sync
Ground
Ground
RS-232C Port: 9-pin D-sub male connector
Pin No. Signal Name
I/O
Reference
1
Not connected
9 8 7 6
2
3
4
5
6
7
8
9
RD
SD
Receive Data
Send Data
Reserved
Signal Ground
Reserved
Input
Output
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Not connected
SG
Reserved
Reserved
5 4 3 2 1
59
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232C Specifications and Command Settings
PC control
A computer can be used to control the projector by connecting an RS-232C cable (null modem, cross type,
commercially available) to the projector. (See page 27 for connection.)
Communication conditions
Set the serial port settings of the computer to match that of the table.
Signal format: Conforms to RS-232C standard.
Baud rate: 9,600 bps
Data length: 8 bits
Parity bit: None
Stop bit: 1 bit
Flow control: None
Basic format
Commands from the computer are sent in the following order: command, parameter, and return code. After
the projector processes the command from the computer, it sends a response code to the computer.
Command format
C1 C2 C3 C4 P1 P2 P3 P4
Return code (0DH)
Command 4-digit
Parameter 4-digit
Response code format
Normal response
Problem response (communication error or incorrect command)
Return code (0DH)
O
K
E
R
R
Return code (0DH)
Info
• When more than one code is being sent, send each command only after the OK response code for the
previous command from the projector is verified.
• When using the computer control function of the projector, the projector’s operating status cannot be read by
the computer.
Commands
Example:
• When power on.
Computer
Projector
→
←
P
O
W
R
_
_
_
1
O
K
CONTROL CONTENTS
COMMAND PARAMETER
RETURN
POWER ON
STANDBY
P O W R _ _ _ 1 OK OR ERR
P O W R _ _ _ 0 OK OR ERR
INPUT 1 (COMPONENT 1)
INPUT 2 (COMPONENT 2)
INPUT 3 (S-VIDEO)
I
I
I
I
I
I
V E D _ _ _ 1 OK OR ERR
V E D _ _ _ 2 OK OR ERR
V E D _ _ _ 3 OK OR ERR
V E D _ _ _ 4 OK OR ERR
V E D _ _ _ 5 OK OR ERR
V E D _ _ _ 6 OK OR ERR
INPUT 4 (VIDEO)
INPUT 5 (RGB/COMPONENT)
DIGITAL MODE
Note
• If an underbar (_) appears in the parameter column, enter a space.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Compatibility Chart
The table below lists signal codes that are compatible with the projector. When the images are distorted or
cannot be projected, adjust the output signal of your computer and so forth while referring to the table below.
Computer
• Horizontal Frequency: 15–70 kHz
Vertical Frequency: 43–75 Hz
Pixel Clock: 12–80 MHz
Compatible with sync on green
XGA compatible in intelligent compression
Horizontal
Vertical
VESA
Standard
DVI
Support
PC/
Frequency Frequency
Resolution
Display
MAC
(kHz)
27.0
(Hz)
60
640 × 350
31.5
27.0
70
60
720 × 350
640 × 400
31.5
27.0
31.5
27.0
31.5
26.2
31.5
34.7
37.9
37.5
70
60
70
60
70
50
60
70
72
75
50
56
60
70
72
75
43
50
70
72
60
VGA
720 × 400
✔
✔
✔
✔
Upscale
✔
640 × 480
✔
✔
✔
✔
✔
✔
✔
✔
✔
PC
31.4
35.1
37.9
44.5
48.1
46.9
35.5
40.3
56.5
58.1
45.0
✔
✔
SVGA
800 × 600
✔
✔
✔
✔
✔
✔
✔
XGA 1,024 × 768
Intelligent
Compression
✔
—
1,280 × 720
PC/
34.9
67
VGA
640 × 480
832 × 624
1,024 × 768
MAC 13"
Upscale
46.8
49.6
48.4
60.0
75
75
60
75
MAC 16" SVGA
✔
✔
Intelligent
Compression
PC/
XGA
MAC 19"
Note
• This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD)
mode. Should this occur, turn off the LCD display on the notebook computer and output the display data
in “CRT only” mode. Details on how to change display modes can be found in your notebook computer’s
owner’s manual.
DTV
Signal
480
480P
540P
576
576P
720P
720P
Horizontal Frequency (kHz)
Vertical Frequency (Hz)
DVI Support
I
15.7
31.5
33.8
15.6
31.3
45.0
37.5
28.1
33.8
28.1
33.8
60
60
60
50
50
60
50
50
60
50
60
✔
I
✔
✔
✔
1035
1035
1080
1080
I
I
I
I
✔
✔
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Check
Page
28
—
• Projector power cord is not plugged into the wall outlet.
• Power to the external connected devices is off.
• The selected input mode is wrong.
29
•
•
Cables are incorrectly connected to the rear panel of the projector. 19-27
External output has not been set when connecting notebook computer.
—
42
42
No picture
• “Contrast” and “Bright” are set to minimum position.
• Image adjustments are incorrectly set.
(Video Input only)
• Video input system is incorrectly set.
(INPUT 5)
48
48
• Input signal type (RGB/Component) is incorrectly set.
Color is faded or poor.
On-screen display does • “OSD Display” is set to “ (OFF)”.
47
not appear.
• Adjust the focus.
• The projection distance exceeds the focus range.
30
17
(Computer Input only)
• Perform “Fine Sync” Adjustments. (“Clock” Adjustment)
• Perform “Fine Sync” Adjustments. (“Phase” Adjustment)
• Noise may appear depending on the computer.
45
45
—
Picture is blurred;
noise appears.
An unusual sound is
occasionally heard
from the cabinet.
• If the picture is normal, the sound is due to cabinet shrinkage
caused by room temperature changes. This will not affect
operation or performance.
—
Maintenance
indicator illuminates or
blinks in red.
• See “Maintenance Indicators”.
54
The cooling fan
becomes noisy.
• When temperature inside the projector increases, the cooling
fan runs faster.
—
The lamp takes a long • The lamp will eventually need to be changed.
57
time to turn on.
The lamp has reached the end of its life. Replace the lamp.
Picture is dark.
• Change the input signal type.
Image is green on
INPUT 5 Component.
Image is pink (no green)
on INPUT 5 RGB.
48
This projector is equipped with a microprocessor. Its performance could be adversely affected by
incorrect operation or interference. If this should happen, unplug the projector and plug it in again
after more than 5 minutes.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Product type DLPTM Projector
Model EIP-1500T
Video system PAL/PAL 60/PAL-M/PAL-N/SECAM/NTSC 3.58/NTSC 4.43
DTV 480I/480P/720P/1080I
Display method Single Panel Digital Micromirror Device (DMD™) by Texas Instruments
DLP panel Panel size: 0.8"
Drive method: Digital Light Processing (DLP™)
No. of dots: 921,600 dots (1,280 [H] × 720 [V])
Lens 1–1.5 × zoom lens, F2.0–2.5, f=21.3–31.6 mm
Projection lamp 275 W DC lamp
Video input signal RCA Connector: VIDEO (INPUT 4), composite video, 1.0 Vp-p, sync negative, 75 Ω
terminated
S-video input signal 4-pin Mini DIN connector (INPUT 3)
Y (luminance signal): 1.0 Vp-p, sync negative, 75 Ω terminated
C (chrominance signal): Burst 0.286 Vp-p, 75 Ω terminated
Component input signal RCA Connector
(INPUT 1, 2) Y: 1.0 Vp-p, sync negative, 75 Ω terminated
PB (CB): 0.7 Vp-p, 75 Ω terminated
PR (CR): 0.7 Vp-p, 75 Ω terminated
Analog RGB/Digital 29-pin DVI-I terminal
(INPUT 5/DIGITAL) <Digital>
Input impedance 50 Ω
Input level 250-1000 mV
<Analog>
Input impedance 75 Ω
Input level 0.7 Vp-p
Y: 1.0 Vp-p, sync negative, 75 Ω terminated
PB (CB): 0.7 Vp-p, 75 Ω terminated
PR (CR): 0.7 Vp-p, 75 Ω terminated
<Synchronization signal>
• Separate sync/Composite sync
Input level TTL level
Input impedance 1 KΩ
• Green on sync
Input level (Synchronizing input) 0.286 Vp-p
Input impedance 75 Ω
Horizontal resolution 720 TV lines (DTV 720P input)
Pixel clock 12–80 MHz
Vertical frequency 43–75 Hz
Horizontal frequency 15–70 kHz
Computer control signal 9-pin D-sub connector (RS-232C Port)
Rated voltage AC 100–240 V
Input current 3.65 A (When using AC 100 V)
Rated frequency 50/60 Hz
Power consumption 360 W (When using AC 100 V)
Power consumption (standby) 6 W (When using AC 100 V)
Heat dissipation 1,350 BTU/hour
Operating temperature 41°F to 95°F (+5°C to +35°C)
Storage temperature –4°F to 140°F (–20°C to +60°C)
Cabinet Plastic
I/R carrier frequency 38 kHz
Dimensions (approx.) 12 7/32" × 3 33/64" × 11 7/64" (310 (W) × 89 (H) × 282 (D) mm) (main body only)
12 7/32" × 4 7/64" × 11 5/16" (310 (W) × 104 (H) × 287 (D) mm) (including adjustment foot
and projecting parts)
Weight (approx.) 9.3 lbs. (4.2 kg)
Replacement parts Remote control, Power cord for U.S., Canada, etc., Power cord for Europe, except U.K.,
Video cable, Lens cap, QUICK GUIDE, Owner’s manual
As a part of policy of continuous improvement, EIKI reserves the right to make design
and specification changes for product improvement without prior notice. The performance
specification figures indicated are nominal values of production units. There may be some
deviations from these values in individual units.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
Units: inches (mm)
Rear View
Side View
Top View
Side View
12 7/32 (310)
2 11/64 (55.05)
Front View
3 15/16 (99.95)
5 7/64 (129.5)
5 7/64 (129.5)
1 7/32
(29.1) (30.9)
1 5/32
M4
M4
Bottom View
M4
M4
1 3/4
1 7/32
(44.1) (30.9)
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
Aspect Ratio
Intelligent compression and expansion
High quality resizing of lower and higher resolu-
tion images to fit the projector’s native resolution.
Width and height ratio of an image. The normal
aspect ratio of a computer and video image is 4:3.
There are also wide images with an aspect ratio
of 16:9 and 21:9.
Keystone Correction
Function to digitally correct a distorted image when
the projector is set up at an angle, smoothes out
jaggies on keystone images and compresses the
image not only horizontally but vertically keeping
the 16 : 9 aspect ratio.
Auto Sync
Optimizes projected computer images by auto-
matically adjusting certain characteristics.
Background
Initial setting image projected when no signal is
being output.
Phase
Phase shift is a timing shift between isomorphic
signals with the same resolution. When phase level
is incorrect, the projected image typically displays
horizontal flicker.
Clock
Clock adjustment is used to adjust vertical noise
when clock level is incorrect.
CLR Temp (Color temperature)
Resize
Function that can be used to adjust the color tem-
perature to suit the type of image input to the pro-
jector. Decrease the color temperature to create
warmer, reddish images for natural flesh tones,
or increase to create cooler, bluish images for a
brighter picture.
Allows you to modify or customize the picture dis-
play mode to enhance the input image. You can se-
lect from four different modes: STRETCH, SIDE
BAR, SMART STRETCH and CINEMA ZOOM.
RS-232C
Function to control the projector from the com-
puter by using the RS-232C ports on the projec-
tor and computer.
Composite sync
Signal combining horizontal and vertical sync
pulses.
Stretch
DVI (Digital Visual Interface)
Display digital interface that also supports analog
interfaces.
Projects the 16:9 image or the squeezed image (*1)
fully in a 16:9 screen.
*1...16:9 image that is squeezed horizontally into
4:3 image
Gamma
Image quality enhancement function that offers a
richer image by brightening the darker portions
of the image without altering the brightness of the
brighter portions. You can select from four differ-
ent modes: Standard, Cinema 1, Cinema 2 and
Cinema 3.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
A
M
AC socket ............................................................. 28
Adjustment buttons .............................................. 38
Aspect ratio .......................................................... 35
Auto Power Off ..................................................... 50
Auto Sync ............................................................. 46
AUTO SYNC button ............................................. 46
MENU button........................................................ 38
Menu Color........................................................... 51
Menu Position ...................................................... 50
O
ON button ............................................................. 28
On-screen display language ................................ 52
OSD Display......................................................... 47
B
Background .......................................................... 49
Blue ...................................................................... 42
Bright .................................................................... 42
Bright Boost.......................................................... 43
P
Phase ................................................................... 45
Picture .................................................................. 42
Picture Mode ........................................................ 44
PICTURE MODE button....................................... 34
Power cord ........................................................... 28
Power indicator .................................................... 10
PRJ mode ............................................................ 52
C
Ceiling+Front........................................................ 52
Ceiling+Rear ........................................................ 52
Clock .................................................................... 45
CLR Temp (Color Temperature) ........................... 42
Color..................................................................... 42
Component terminals ........................................... 21
Contrast................................................................ 42
R
Rear ..................................................................... 52
Rear adjustment feet............................................ 31
Red....................................................................... 42
Remote control..................................................... 12
Remote control sensor ......................................... 13
Replacing the lamp .............................................. 56
RESIZE button ..................................................... 34
RS-232C terminal................................................. 27
D
DIGITAL INPUT button ......................................... 29
DVI ........................................................ 22,23,25,26
E
Eco Mode ............................................................. 49
ENTER button ...................................................... 39
Exhaust vent ................................................ 7,11,53
S
Sharp.................................................................... 42
Signal Info ............................................................ 46
Signal Type .......................................................... 48
Special Modes...................................................... 45
STANDBY-ON button ........................................... 28
STRETCH ............................................................ 35
S-video input terminal .......................................... 24
F
Fine Sync ............................................................. 45
Front ..................................................................... 52
G
Gamma Adj. ......................................................... 43
T
H
Temperature warning indicator............................. 54
Tint ....................................................................... 42
HEIGHT ADJUST button ...................................... 31
H-Pos ................................................................... 45
U
I
UNDO button........................................................ 34
INPUT buttons...................................................... 29
Intake vent......................................................... 7,53
IRIS ................................................................. 34,44
IRIS button ........................................................... 34
V
Video input terminal ............................................. 24
Video System ....................................................... 48
V-Pos.................................................................... 45
K
Z
Kensington Lock .................................................. 11
KEYSTONE button............................................... 32
Keystone Correction............................................. 32
ZOOM-FOCUS button.......................................... 30
L
Lamp .................................................................... 56
Lamp indicator...................................................... 54
Lamp Timer (Life) ................................................. 47
Language ............................................................. 52
Lens cap................................................................. 9
66
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
Download from Www.Somanuals.com. All Manuals Search And Download.
A-Key to better communications
Canada
U.S.A.
EIKI International, Inc.
30251 Esperanza
Rancho Santa Margarita
CA 92688-2132
EIKI CANADA - Eiki International, Inc.
P.O. Box 156, 310 First St. - Unit 2,
Midland, ON, L4R 4K8, Canada
Tel : 800-563-3454 (705)-527-4084
Fax: 800-567-4069 (705)-527-4087
E-Mail : [email protected]
U.S.A.
Tel : 800-242-3454 (949)-457-0200
Fax: 800-457-3454 (949)-457-7878
E-Mail : [email protected]
Eastern Europe
EIKI CZECH spol. s.r.o.
Umelecká 15
Deutschland & Österreich
EIKI Deutschland GmbH
Am Frauwald 12
170 00 Praha 7
Czech Republic
65510 Idstein
Deutschland
Tel : +42 02 20570024
+42 02 20571413
Tel : 06126-9371-0
Fax: 06126-9371-14
E-Mail : [email protected]
Fax: +42 02 20571411
E-Mail : [email protected]
Japan & Worldwide
EIKI Industrial Company Limited.
4-12 Banzai-Cho, Kita-Ku, Osaka,
530-0028 Japan
Tel : +81-6-6311-9479
Fax: +81-6-6311-8486
Printed in China
TINS-B931WJZZ
05P08-CH-NM
Download from Www.Somanuals.com. All Manuals Search And Download.
|