OPERATOR’S MANUAL
ENGINE DRILL
EDR-260
WARNING
READ INSTRUCTIONS CAREFULLY AND FOLLOW RULES FOR
SAFE OPERATION.
FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY.
ECHO POWER EQUIPMENT(CANADA)
501 Newbold Street, London, Ontario Canada N6E 1K4
X750-005 04 5
X750409-3705
Printed in Japan 0907mh 1091 ES
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
ECHO Engine Drill EDR-260 is a lightweight, high
performance, two-stroke engined unit designed for
drilling.
WARNING
IMPROPER USE OR CARE OF THIS UNIT, OR
FAILURE TO WEAR PROPER PROTECTION
CAN RESULT IN SERIOUS INJURY.
READ AND UNDERSTAND THE RULES FOR
SAFE OPERATION AND ALL INSTRUCTIONS
IN THIS MANUAL.
This Manual provides the information necessary
for operation and maintenance.
SAFETY AND SPECIAL INFORMATION
CIRCLE AND SLASH SYMBOL
This symbol means the specific action
shown is prohibited. Ignoring these
prohibitions can result in serious or
fatal injury.
DANGER
The safety alert symbol accompanied by the
word “DANGER” calls attention to an act or
condition which WILL lead to serious
personal injury or death if not avoided.
NOTE
WARNING
This enclosed message provides tips for use,
care and maintenance of the unit.
The safety alert symbol accompanied by the
word “WARNING” calls attention to an act or
condition which CAN lead to serious
personal injury or death if not avoided.
IMPORTANT
The enclosed message provides information
necessary for the protection of the unit.
CAUTION
Throughout this manual and on the product itself,
you will find safety alters and helpful, information
messages preceded by symbols or key words.
The following is an explanation of those symbols
and key words and what they mean to you.
The safety alert symbol accompanied by the
word “CAUTION” calls attention to an act or
condition which may lead to minor or
moderate personal injury if not avoided.
WARNING
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose
objects away from all openings.
• ALWAYS stop engine, disconnect spark plug, and make sure all moving parts have come to a
complete stop before removing obstructions, clearing debris, or servicing unit.
• DO NOT start or operate unit unless all guards and protective covers are properly assembled
to unit.
• NEVER reach into any opening while the engine is running. Moving parts may not be visible
through openings.
WARNING
Check fuel system for leaks due to fuel tank damage, especially if the unit is dropped. If damage
or leaks are found, do not use unit, otherwise serious personal injury or property damage may
occur. Have unit repaired by an authorized servicing dealer before using.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
EMISSION CONTROL (EXHAUST & EVAPORATIVE)
EPA Phase 2 / C.A.R.B. TIER III
The emission control system for the engine is EM/TWC (Engine Modification and 3-way Catalyst) and for
the fuel tank the Control System is EVAP (Evaporative Emissions) or N (for Nylon Tank). Evaporative
emission may be applicable to California models only.
An Emission Control Label is located on the engine.
(This is an EXAMPLE ONLY, information on label
varies by engine FAMILY).
PRODUCT EMISSION DURABILITY (EMISSION COMPLIANCE PERIOD)
The 300 hour emission compliance period is the time span selected by the manufacturer certifying
the engine emissions output meets applicable emissions regulations, provided that approved
maintenance procedures are followed as listed in the Maintenance Section of this manual.
CONTENTS
Introduction ............................................................................................................................................. 1
Safety and Special Information ............................................................................................................... 1
Safety ...................................................................................................................................................... 3
Operating Techniques ............................................................................................................................. 5
Description .............................................................................................................................................. 6
Assembling.............................................................................................................................................. 7
Operation ................................................................................................................................................ 7
Maintenance and Care ............................................................................................................................ 12
Trouble shooting...................................................................................................................................... 13
Maintenance............................................................................................................................................ 14
Storage.................................................................................................................................................... 17
Specifications .......................................................................................................................................... 18
Specifications, descriptions and illustrative material in this literature are as accurate as known at the time
of publication, but are subject to change without notice. Illustrations may include optional equipment and
accessories, and may not include all standard equipment.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
WARNING
WARNING
ENGINE DRILL USERS RISK INJURY TO
THEMSELVES AND OTHERS IF THE ENGINE
DRILL IS USED IMPROPERLY, AND/OR
SAFETY PRECAUTIONS ARE NOT
FOLLOWED. PROPER CLOTHING AND
SAFETY GEAR MUST BE WORN WHEN
OPERATING ENGINE DRILL.
ALWAYS STOP THE ENGINE WHEN A DRILL
JAM OCCURS. DO NOT ATTEMPT TO
REMOVE AN OBJECT CAUSING A DRILL
JAM IF THE ENGINE IS RUNNING. PHYSICAL
INJURY CAN OCCUR IF A DRILL JAM IS
REMOVED AND THE DRILLS START
MOVING.
•
Do all drilling at full throttle speed. Drilling at
less at than full speed can damage the clutch
by allowing it to slip.
OPERATOR SAFETY
•
Read this Engine drill Operator’s Manual
carefully. Be sure you understand how to
operate this unit properly before you use it.
WARNING
USE A FIRM GRIP WITH THUMBS AND
FINGERS ENCIRCLING THE HANDLES. A
FIRM GRIP WILL HELP YOU KEEP
•
•
•
Be familiar with all the controls and the proper
use of the machine.
CONTROL OF THE ENGINE DRILL. NEVER
OPERATE THE ENGINE DRILL ONLY ONE
HAND OR BODILY INJURY CAN OCCUR.
Wear proper clothing to protect legs and other
exposed parts of your body.
Wear non-skid sole shoes. Do not wear open-
toed shoes or operate unit while bare footed.
•
Always carry the engine drill with the engine
stopped and the HOT muffler away from your
body.
•
•
Wear eye and hearing protection devices.
Use caution when handling fuel. Put the caps
back tightly on both the fuel can and the
engine drill fuel tank.
PROTECTIVE EQUIPMENT
•
Always wear eye protection goggles that meet
ANSI Z87.1 standards.
Move at least 3 m (10 feet) from the re-fueling
point and be sure there is no leakage of fuel
from the fuel tank cap or the fuel system before
starting the engine.
•
Wear hearing protection.
ECHO recommends that hearing protection be
worn at all times.
•
•
Operate this gasoline powered engine
equipment in a well-ventilated area only.
•
•
Dress properly! Do not wear loose clothing or
jewellery, they can be caught in moving parts.
Use of sturdy gloves, non-skid footwear, and
safety glasses is recommended.
Start the unit on the ground with the throttle set
at idle. Do not start if the drills are obstructed
by the ground or any other object.
While operating the machine always be sure of
a secure position.
•
•
Never allow children to use the machine.
Do not allow anyone to hold the material you
are drilling.
•
Keep a firm grip on the engine drill with both
hands, one hand on the front handle, the other
hand on the rear handle.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Wear non-slip, heavy-duty work gloves to
improve your grip on the engine drill handles.
The gloves also help reduce the transmission
of machine vibrations to your hands.
WARNING
PRECAUTION AGAINST VIBRATION
AND COLD
IT IS BELIEVED THAT A CONDITION
CALLED RAYNAUD’S PHENOMENON,
WHICH AFFECTS THE FINGERS OF
CERTAIN INDIVIDUALS MAY BE BROUGHT
ABOUT BY EXPOSURE TO VIBRATION AND
COLD. EXPOSURE TO VIBRATION AND
COLD MAY CAUSE TINGLING AND
PROTECTING OTHERS
Spectators, children, fellow workers and animals
must be warned to come no nearer than 4.6 m (15
feet) while the engine drill is in use.
People working in the area near you should wear
the same protective equipment as the operator.
BURNING SENSATIONS FOLLOWED BY
LOSS OF COLOR AND NUMBNESS IN THE
FINGERS. THE FOLLOWING PRECAUTIONS
ARE STRONGLY RECOMMENDED BECAUSE
THE MINIMUM EXPOSURE WHICH MIGHT
TRIGGER THE AILMENT IS UNKNOWN.
PHYSICAL CONDITION
Your judgement and dexterity may be impaired if
you are ill or have taken alcohol or other
substances known to affect the way you would
normally function.
• KEEP YOUR BODY WARM, ESPECIALLY
THE HEAD, NECK, FEET, ANKLES, HANDS
AND WRISTS.
• MAINTAIN GOOD BLOOD CIRCULATION
BY PERFORMING VIGOROUS ARM
EXERCISES DURING FREQUENT WORK
BREAKS AND ALSO BY NOT SMOKING.
• LIMIT THE HOURS OF OPERATION. TRY
TO FILL EACH DAY WITH JOBS WHERE
OPERATING THE ENGINE DRILL OR
OTHER HAND-HELD POWER EQUIPMENT
IS NOT REQUIRED.
• IF YOU EXPERIENCE DISCOMFORT,
REDNESS AND SWELLING OF THE
FINGERS FOLLOWED BY WHITENING AND
LOSS OF FEELING, CONSULT YOUR
PHYSICIAN BEFORE FURTHER EXPOSING
YOURSELF TO COLD AND VIBRATION.
Painful or numb fingers?
See your doctor
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Repetitive Stress Injuries
It is believed that over-using the muscles and
tendons of the fingers, hands, arms and shoulders
may cause soreness, swelling, numbness,
weakness and extreme pain in those areas.
Certain repetitive hand activities may put you at a
high risk for developing a Repetitive Stress Injury
(RSI). An extreme RSI condition is Carpal Tunnel
Syndrome (CTS), which could occur when your
wrist swells and squeezes a vital nerve that runs
through the area. Some believe that prolonged
exposure to vibration may contribute to CTS.
CTS can cause severe pain for months or even
years. To reduce the risk of RSI/CTS, do the
following:
•
Avoid using your wrist in a bent, extended or
twisted position. Instead try to maintain a
straight wrist position. Also, when grasping,
use your whole hand, not just the thumb
and index finger.
•
•
•
•
Take periodic breaks to minimize repetition
and rest your hands.
Reduce the speed and force with which you do
the repetitive movement.
Do exercise to strengthen the hand and arm
muscles.
See a doctor if you feel tingling, numbness or
pain in the fingers, hands, wrists or arms.
The sooner RSI/CTS is diagnosed, the more
likely permanent nerve and muscle damage
can be prevented.
OPERATING TECHNIQUES
•
When starting to drill, run the engine at full
throttle.
•
•
•
Do not attempt to repair the machine unless
you are qualified to do so.
WARNING
Do not operate the machine with a damaged or
excessively worn drill bit.
BEFORE DRILLING, BE SURE TO READ AND
UNDERSTAND THE ENTIRE OPERATOR’S
MANUAL TO AVOID THE CHANCE OF
SERIOUS INJURY.
Always ensure all handles and guards are
fitted when using the machine. Never attempt
to use an incomplete machine or one fitted with
an unauthorized modification.
•
•
Do not force the drills and only move as
quickly as the drills will allow.
•
•
•
When transporting or storing the machine
always remove the drill bit.
Stop the engine and disconnect from ignition
cable before: - cleaning or when clearing a
blockage; checking, maintenance or working
on the machine.
To reduce fire hazard keep engine and silencer
free of debris, leaves or excessive grease.
Handle drill with care, contacting with drills
may cause injury.
•
Handle fuel with care; it is highly flammable.
Never add fuel to a machine with a running or
hot engine.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
DESCRIPTION
2
3
1
4
Part Number X505-002310
Part Number X505-002570
15
14
13
12
11
Part Number X505-002310
Part Number X505-002570
10
9
8
6
7
5
* If a decal cannot be read, a new one can be
ordered from your ECHO dealer.
1. Operator’s manual - Included with unit. Read
before operation and keep for future reference
to learn proper, safe operating techniques.
9. Fuel tank - Contains fuel and fuel filter.
10. Fuel tank cap - For closing the fuel tank.
11. Air cleaner cover - Covers air filter.
2. Throttle trigger - Device activated by the
operator’s finger, for controlling the engine
speed.
12. Starter handle - Pull handle to start the
engine.
13. Throttle trigger lockout - Device that
3. Rear handle - Handle located furthest from the
prevents the accidental operation of the throttle
trigger until manually released.
drill bit.
4. Silencer cover
14. Ignition switch - Device for allowing the
5. Drill bit - Not included with unit.
6. Chuck
engine to be started and stopped.
15. Spark plug
7. Front handle - Handle located on the front
gear case.
8. Shift lever
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLING
FRONT HANDLE
•
Insert the front handle to the machine, and turn
clockwise. (TIGHTEN THE SCREW FIRMLY)
- To operate front handle with right hand,
remove right plug then reverse sides when
installing handle and plug.
Washer
Front handle
DRILL BIT
•
Loosen the chuck and insert the drill bit (not
provided with unit). Then tighten the chuck by
turning it clockwise.
Chuck
Drill bit
IMPORTANT
Use drill bits suited for the material being
drilled and for the depth of hole required.
Plug
OPERATION
WARNING
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose
objects away from all openings. Always stop engine, disconnect spark plug, and make sure all
moving parts have come to a complete stop before removing obstructions, clearing debris, or
servicing unit.
WARNING
Engine exhaust IS HOT, and contains Carbon Monoxide (CO), a poison gas. Breathing CO can
cause unconsciousness,serious injury, or death. Exhaust can cause serious burns. ALWAYS
blow exhaust away from your face and body.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
CHECK UP OF NUTS AND OTHER
HARDWARES
WARNING
ALTERNATIVE FUELS, SUCH AS E-20 (20 %
ETHANOL), E-85 (85 % ETHANOL) OR ANY
FUELS NOT MEETING ABOVE
•
Check up loose nuts, bolts and screws before
using the unit every day.
REQUIREMENTS ARE NOT APPROVED FOR
USE IN ECHO 2-STROKE GASOLINE
ENGINES.
FUEL STATEMENT
USE OF ALTERNATIVE FUELS MAY CAUSE
PERFORMANCE PROBLEMS, LOSS OF
POWER, OVERHEATING, FUEL VAPOR
LOCK, AND UNINTENDED MACHINE
OPERATION, INCLUDING, BUT NOT LIMITED
TO, IMPROPER CLUTCH ENGAGEMENT.
ALTERNATIVE FUELS MAY ALSO CAUSE
PREMATURE DETERIORATION OF FUEL
LINES, GASKETS, CARBURETOR AND
OTHER ENGINE COMPONENTS.
GASOLINE - Use 89 Octane [(R+M)/2] (mid grade
or higher) gasoline or gasohol known to be good
quality.
Gasohol may contain up to 10 % Ethyl (grain)
alcohol or 15 % MTBE (methyl tertiary-butyl ether).
Gasohol containing methyl (wood) alcohol is NOT
approved.
Two-Stroke Oil - A two-stroke engine oil meeting
ISO-L-EGD (ISO/CD 13738) and J.A.S.O. FC/FD
Standards must be used. ECHO brand premium
Power Blend X™ Universal 2-Stroke Oil meets these
standards. Engine problems due to inadequate
lubrication caused by failure to use an ISO-L-EGD
(ISO/CD 13738) and J.A.S.O. FC/FD certified oil,
such as ECHO premium Power Blend X™, will void
the two-stroke engine warranty.
Fuel Mix Chart 50 : 1
US.
METRIC
Gasoline
Gasoline
Gallons
Oil
Oil
US. fl. oz.
L
mL
1
2
5
2.6
5.2
12.8
4
8
20
80
160
400
IMPORTANT
• ECHO premium Power Blend X™ Universal
2-Stroke Oil may be mixed at 50 : 1 ratio for
application in all ECHO engines sold in the
past regardless of ratio specified in those
manuals.
• Use of unmixed, improperly mixed, or fuel
older than 90 days, (stale fuel), may cause
hard starting, poor performance, or severe
engine damage and void the product
warranty. Read and follow instructions in
the Storage section of this manual.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
HANDLING FUEL
MIXING INSTRUCTIONS -
1. Fill an approved fuel container with half of the
DANGER
FUEL IS VERY FLAMMABLE. USE EXTREME
CARE WHEN MIXING, STORING OR
HANDLING OR SERIOUS PERSONAL
INJURY MAY RESULT.
• USE AN APPROVED FUEL CONTAINER.
• DO NOT SMOKE NEAR FUEL.
• DO NOT ALLOW FLAMES OR SPARKS
NEAR FUEL.
• FUEL TANKS/CANS MAY BE UNDER
PRESSURE.
ALWAYS LOOSEN FUEL CAPS SLOWLY
ALLOWING PRESSURE TO EQUALIZE.
• NEVER REFUEL A UNIT WHEN THE
ENGINE IS HOT!
required amount of gasoline.
2. Add the proper amount of two-stroke oil to
gasoline.
3. Close container and shake to mix oil with
gasoline.
4. Add remaining gasoline, close fuel container,
and remix.
IMPORTANT
• Spilled fuel is a leading cause of
hydrocarbon emissions. Some states may
require the use of automatic fuel shut-off
containers to reduce fuel spillage.
• Stored fuel ages.
• NEVER REFUEL A UNIT WITH THE
ENGINE RUNNING.
Do not mix more fuel than you expect to
use in thirty (30) days, ninety (90) days
when a fuel stabilizer is added.
• DO NOT FILL FUEL TANKS INDOORS.
ALWAYS FILL FUEL TANKS OUTDOORS
OVER BARE GROUND.
• Stored two-stroke fuel may separate.
ALWAYS shake fuel container thoroughly
before each use.
• DO NOT OVERFILL FUEL TANK. IT IS NOT
PERMITTED TO FILL FUEL ABOVE THE
SHOULDER LEVEL OF FUEL TANK. WIPE
UP SPILLS IMMEDIATELY.
• SECURELY TIGHTEN FUEL CAP AFTER
REFUELING.
• INSPECT FOR FUEL LEAKAGE.
IF FUEL LEAKAGE IS FOUND, DO NOT
START OR OPERATE UNIT UNTIL
LEAKAGE IS REPAIRED.
• MOVE AT LEAST 3 M (10 FEET) FROM
REFUELING LOCATION BEFORE
STARTING THE ENGINE.
AFTER USE -
DO NOT store a unit with fuel in its tank. Leaks can
occur. Return unused fuel to an approved fuel
storage container.
STORAGE -
Fuel storage laws vary by locality. Contact your
local government for the laws affecting your area.
As a precaution, store fuel in an approved, airtight
container. Store in a well-ventilated, unoccupied
building, away from sparks and flames.
Shoulder level
Fuel tank
9
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTING COLD ENGINE
WARNING
WHEN ENGINE IS STARTED, CONFIRM IF
THERE IS NOT ANY ABNORMAL VIBRATION
OR SOUND. IF THERE IS ABNORMAL
VIBRATION OR SOUND, ASK YOUR DEALER
TO REPAIR.
•
•
Stand the engine upright on a level surface.
Place ignition switch in ON (START/RUN)
position.
ON
Ignition switch
•
Push purge bulb 3 to 4 times (or until fuel is
visible in fuel return line).
STOP
•
•
•
Shift choke lever to close position (START).
Pull starter handle until the engine fires.
Throttle trigger
Throttle trigger lockout
Starter handle
Shift choke lever to full open position, and if
necessary, start the engine again and allow to
warm up before using.
- The clutch engages at approximately 3500
r/min. Therefore the drill bit may rotate at
fast idle engine speed.
STARTING WARM ENGINE
•
Place ignition switch in ON (START/RUN)
position.
Push
•
Pull starter handle until the engine fires.
- Do not use the choke.
Purge bulb
Fuel return line
STOPPING ENGINE
START
(Close)
•
Set throttle trigger in idle position.
•
Place ignition switch in STOP position.
NOTE
RUN
(Open)
When engine does not stop, shift choke lever to
close position.
Check and repair ignition switch before starting
the engine again.
Choke lever
10
Download from Www.Somanuals.com. All Manuals Search And Download.
REVERSE ROTATION
•
•
•
This model is equipped with reverse rotation
mechanism.
Counter
clockwise
(CCW)
When drilling, set shift lever down to clockwise
(CW) rotation position.
If bit is locked due to deep penetration during
drilling operation, set shift lever up to
counterclockwise (CCW) rotation position and
operate reversed for easy pulling-out.
Clockwise
(CW)
Shift lever
•
When changing direction of drill rotation,
operate as follows:
- Return engine to idle.
- Engine shift lever to CW or CCW position
with a slight acceleration of the throttle
trigger.
To properly lock the gears in the gear case.
- Do not operate shift lever forcibly when
changing rotation direction.
NOTE
WARNING
• WHEN THE DRILL CAN NOT PULL OUT
FROM THE WOOD, DO NOT TRY TO PULL
OUT THE DRILL BY FORCE.
Do not shift from forward to reverse (or vice-
versa) while the chuck is turning.
Failure to do so may cause unit damage.
Always release throttle and allow the unit to
return to idle before shifting.
• WHEN CHANGING THE BIT, ENSURE TO
STOP THE ENGINE.
• AFTER A JOB, BIT AND GEAR CASING
MAY BE HEATED, DO NOT TOUCH THEM
WITH BARE HANDS.
Do not stand close to drill or chuck with your
body or clothes while operation.
When drilling, ensure that no power cable or
other obstacle exist.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE AND CARE
REQ'D
3 MONTHS
OR 90
MAINTENANCE
PROCEDURE
DAILY OR
EVERY
YEARLY
COMPONENT / SYSTEM
SKILL
BEFORE USE REFUEL
600 HOURS
LEVEL
HOURS
Air Filter
Inspect/Clean
1
1
1
1
1
1
2
2
2
1
1
I / C *
I / C
R *
Choke Shutter
Fuel Filter
Inspect/Clean
Inspect/Replace
I *
I *
I / R *
R
Fuel Cap Gasket
Fuel System
Inspect/Replace
Inspect/Replace
I (1) *
I / C
I (1) *
Spark Plug
Inspect/Clean/Replace
Inspect/Clean
I / C / R *
Cooling System
Muffler Spark Arrestor
Cylinder Exhaust Port
Recoil Starter Rope
Screws/Nuts/Bolts
Inspect/Clean/Replace
Inspect/Clean/Decarbon
Inspect/Clean
I / C / R *
I / C
I / C *
I *
Inspect/Tighten/Replace
MAINTENANCE PROCEDURE LETTER CODES: I = INSPECT, R = REPLACE, C = CLEAN
IMPORTANT NOTE - Time intervals shown are maximum. Actual use and your experience will determine the
frequency of required maintenance.
MAINTENANCE PROCEDURE NOTES:
(1) Low evaporative fuel tanks DO NOT require regular maintenance to maintain emission integrity.
* All recommendations to replace are based on the finding of damage or wear during inspection.
IMPORTANT
Time intervals are maximum. Actual use and
your experience will determine the frequency
of required maintenance.
Record dates of monthly and yearly
inspections.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE SHOOTING
Trouble
Engine - hard to start
Cause
Remedy
-
does not start
Engine
cranks
Fuel at
No fuel
• Fuel filter clogged
at carburetor • Fuel line clogged
• Carburetor
• Clean or replace
• Clean
carburetor
• Ask your ECHO dealer
Fuel at
No fuel at
cylinder
• Carburetor
• Ask your ECHO dealer
cylinder
Silencer wet • Fuel mixture is too rich
with fuel
• Open choke
• Clean/replace air filter
• Adjust carburetor
• Ask your ECHO dealer
Spark at
end of
No spark at
end of plug
wire
• Ignition switch off
• Electrical problem
• Turn switch on
• Ask your ECHO dealer
plug wire
Spark at
plug
No spark at
plug
• Spark gap incorrect
• Adjust 0.6 to 0.7 mm
(0.024 to 0.028 in)
• Clean or replace
• Clean or replace
• Replace plug
• Covered with carbon
• Fouled with fuel
• Spark plug defective
Engine
• Internal engine problem
• Ask your ECHO dealer
does not
crank
Engine
runs
Dies or
• Air filter dirty
• Clean or replace
• Clean or replace
• Clean
accelerates poorly
• Fuel filter dirty
• Fuel vent blocked
• Spark plug
• Clean and adjust/replace
• Adjust
• Carburetor
• Cooling system blocked
• Exhaust port/spark
arrester screen blocked
• Clean
• Clean
WARNING
• ALL ENGINE DRILL SERVICE OPERATIONS, OTHER THAN ITEMS LISTED IN THE
OPERATOR’S MANUAL, SHOULD BE PERFORMED BY AN AUTHORIZED ECHO DEALER.
• FUEL VAPORS ARE EXTREMELY FLAMMABLE AND MAY CAUSE FIRE AND/OR
EXPLOSION. NEVER TEST FOR IGNITION SPARK BY GROUNDING SPARK PLUG NEAR
CYLINDER PLUG HOLE, OTHERWISE SERIOUS PERSONAL INJURY MAY RESULT.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
AIR FILTER
•
Clean before use.
- Remove air cleaner cover and pull out air
filter.
- Lightly brush off dust or wash it in water and
detergent.
- Dry completely before putting it back in
place.
Air filter
Air cleaner cover
FUEL FILTER
•
Check periodically.
- Do not allow dust to enter into fuel tank.
- Clogged filter will cause difficulty in starting
engine or poor engine performances.
- Pick up fuel filter through fuel inlet port with
a piece of steel wire or the like.
- When filter is dirty, replace it.
Fuel tank cap
Fuel filter
CHECK FUEL SYSTEM
•
Check before every use.
•
After refueling, make sure fuel does not leak or
exude from around fuel pipe, fuel grommet or
fuel tank cap.
•
In case of fuel leakage or exudation there is a
danger of fire. Stop using the machine
immediately and request your dealer to inspect
or replace.
SPARK PLUG
•
Check periodically.
- The standard spark gap is 0.6 to 0.7 mm
(0.024 to 0.028 in).
- Correct spark gap if it is wider or narrower
than the standard gap.
- If the electrodes are coated with carbon
deposits replace with a new spark plug.
Do not sandblast to clean.
0.6 - 0.7 mm (0.024 - 0.028 in)
Remaining sand will damage engine.
•
Fastening torque = 15 to 17 N • m
(130 to 145 in • lb).
IMPORTANT
Do not over tighten plug.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT OF CHUCK
Replacement of chuck should be done in the
following manner:
1. Fit 19 mm spanner onto driving axle and keep
it fitted.
2. Remove bolt with hexagonal hole fixed in the
driving axle.
3. Insert accessory hexagonal bar (Part Number
895412-20960) into chuck and fix.
Spanner (19 mm)
4. Fit 10 mm box spanner onto the hexagonal bar
and turn it into direction as indicated by an
arrow to remove chuck.
5. Fit a new chuck in the reversed order of
removing.
Box spanner
(10 mm)
Spanner (19 mm)
Hexagonal bar
(Part Number 895412-20960)
ADJUSTING CARBURETOR
(As Required)
GENERAL INFORMATION
The idle speed adjuster screw controls the throttle
opening at the idle position.
IDLE ADJUSTMENT
1. Start engine and allow it to run at high idle until
warm.
2. Turn the idle speed screw clockwise until drill
bit begins to move.
Idle speed adjustment screw
3. Turn idle screw counterclockwise 1 and 1/2 to 2
turn or until the drill bit stops (2700 to 3300
r/min).
NOTE
When there is some trouble with the carburetor,
contact your dealer.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEANING CYLINDER FINS
Cylinder fins
(Check Periodically)
NOTE
Clogged fins will cause poor engine cooling.
1. Carefully remove housing and clean dirt and
dust from fins.
2. Reinstall housing.
CLEANING SILENCER AND
EXHAUST PORT
(Check Periodically)
1. Carefully remove housing halves.
2. Remove and disassemble silencer.
NOTE
Be careful not to scratch the cylinder or piston
when cleaning the cylinder exhaust port.
Silencer cover
Silencer
3. Clean deposits from cylinder exhaust port and
silencer.
Exhaust Port Cleaning
Level 2.
Tools required: 4 mm Hex Wrench, Wood or
plastic scraper
Parts Required:As needed: Heat Shield
A
1. Remove spark plug lead from spark plug, and
remove engine cover (2 screws).
B
2. Place piston at top dead center. Remove
muffler (A) and heat shield (B).
3. Use a wood or plastic scraping tool to clean
deposits from cylinder exhaust port.
IMPORTANT
Never use a metal tool to scrape carbon from
the exhaust port.
Do not scratch the cylinder or piston when
cleaning the exhaust port. Do not allow
carbon particles to enter the cylinder.
4. Inspect heat shield, and replace if damaged.
5. Install heat shield and muffler.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Tighten muffler mounting bolts (or nuts) to 80-
95 in•lbf (90-110 kgf•cm).
7. Start engine, and warm to operating temperature.
8. Stop engine, and re-tighten mounting bolts (or
nuts) to specifications.
9. Install engine cover and attach spark plug lead.
STORAGE
6. Drain the fuel tank completely and pull the
recoil starter handle several times to remove
fuel from the carburetor.
LONG TERM STORAGE
(Over 30 Days)
7. Remove the spark plug and pour 1/2
tablespoon (1/4 oz) of fresh, clean, 2-stroke
engine oil into the cylinder through the spark
plug hole.
Do not store your unit for a prolonged period of
time (30 days or longer) without performing
protective storage maintenance which includes the
following:
A. Place a clean cloth over the spark plug hole.
1. Store unit in a dry, dust free place, out of the
reach of children and other unauthorized
persons.
B. Pull the recoil starter handle 2 or 3 times to
distribute the oil inside the engine.
C.Observe the piston location through the
spark plug hole. Pull the recoil starter handle
slowly until the piston reaches the top of its
travel and leave it there.
2. Place ignition switch in STOP position.
3. Remove accumulation of grease, oil, dirt and
debris from exterior of unit.
4. Perform all periodic lubrication and services
that are required.
8. Install the spark plug (do not connect ignition
cable).
5. Tighten all the screws, bolts and nuts.
9. Lubricate the drill bit with a heavy coat of oil to
prevent rust.
NOTE
WARNING
DO NOT STORE IN AN ENCLOSURE WHERE
FUEL FUMES MAY ACCUMULATE OR
REACH AN OPEN FLAME OR SPARK.
For future reference, you should keep this
operator’s manual.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
EDR-260
Mass
Volume
fuel tank
Drill
without drill bit
kg
L
5.18 (11.42 lb)
0.58 (19.6 US fl. oz.)
size
mm
mm
32 - 178 (1.25 - 7 inch)
13 (0.5 inch)
chuck capacity
speed
r/min 610
Mission
reduction ratio
17.1 (regular side)
19.0 (reverse side)
grease
lubrication
External Dimensions
length × width × height
mm
450 × 340 × 290
without drill bit
(17.72 × 13.39 × 11.42 inch)
Engine
type
Air cooled Two stroke single cylinder
engine displacement
mL(cm³) 25.4 (1.55 cu. inch)
r/min 10500
recommended maximum engine speed
recommended engine idling speed
r/min 2800
engine speed at beginning of clutch engagement
r/min 3600
carburetor
ignition
diaphragm type
flywheel magneto - CDI system
spark plug
starter
NGK BPMR8Y
recoil starter
clutch
automatic centrifugal
Fuel
mixture ratio
50:1 ratio with ECHO Power Blend X™,
ISO-L-EGD (ISO/CD 13738) and JASO
M345-FC/FD two-stroke, air-cooled engine
oil.
gasoline
Use 89 octane unleaded. Do not use fuel
containing methyl alcohol, more than 10%
ethyl alcohol or 15% MTBE. Do not use
alternative fuels such as E-20 or E-85.
fuel consumption at engine maximum power
L/h
0.62 (20.97 US fl. oz.)
18
Download from Www.Somanuals.com. All Manuals Search And Download.
|