First Alert Home Security System FA148C User Manual

Previous Menu

)$ꢁꢂꢃ&

)$ꢁꢂꢃ&ꢄ&1

6HFXULW\ꢀ6\VWHP

ARMED

READY

FA560

HEAT

COOL

BYPASS

ACTIVE

8VHUꢀ*XLGH

K4855V1 3/00

Download from Www.Somanuals.com. All Manuals Search And Download.

System Overview

General Information

Congratulations on your ownership of a First Alert Professional

Security System. You've made a wise decision in choosing it, for it

represents the latest in security protection technology today,

including microcomputer technology to monitor all system status.

Basically, this system offers you three forms of protection: burglary,

fire, and emergency. Your system may consist of at least one keypad

which provides full control of system operation, various sensors such

as motion detectors and door and window sensing devices, plus a

selected number of strategically placed smoke or combustion detectors

designed to provide early warning in case of fire. Your system may

also have been programmed to automatically transmit alarm or status

messages over the phone lines to a central alarm monitoring station.

All system functions are controlled by your keypad(s), which are

described in the next section, ABOUT THE KEYPADS.

Zones

Your system's sensing devices have been assigned to various "zones".

For example, the sensing device on your Entry/Exit door may have

been assigned to zone 06, sensing devices on windows in the master

bedroom to zone 10, and so on. These zone numbers will appear on the

display when an alarm or trouble condition occurs.

Burglary Protection

Your FA148C provides five modes of burglary protection: STAY,

NIGHT-STAY, AWAY, INSTANT, and MAXIMUM, and allows you to

bypass selected zones while leaving the rest of the system armed. You

must turn on (arm) the burglary protection portion of your system

before it will sense burglary alarms. The system also provides a

CHIME mode, for alerting users to the opening of protected doors and

windows while the system is disarmed. Refer to the other sections of

this manual for procedures for using these features.

- 4 -

Download from Www.Somanuals.com. All Manuals Search And Download.

System Overview (cont'd)

The following table lists the five different arming modes and the

features of each.

FEATURES OF EACH ARMING MODE

ARMING

Exit

Entry

Delay

Perimeter

Armed

Interior

Armed

MODE

Delay

AWAY

NIGHT-STAY

STAY

Yes

Yes*

INSTANT

MAXIMUM

Yes

* for selected interior zones (ask your installer about the included zones)

Security Codes

At the time of installation, you were assigned a personal four-digit

security code, known only to you. You must enter the security code

when arming and disarming the system, and when performing other

system functions. As an additional safety feature, other users who do

not need to know your code can be assigned different security codes.

Refer to the Secu r ity Cod es section for procedures on adding security

codes to the system.

Fire Protection

The fire protection portion of your security system (if used) is always

active and will sound an alarm if a fire condition is detected. Refer to

the Fir e Ala r m System section for important information concerning

fire protection, smoke detectors, and planning emergency exit routes

from the premises.

Alarms

When an alarm occurs, both the keypad and external sounders will

sound, and the keypad will display the zone(s) causing the alarm. If

your system is connected to a central monitoring station, an alarm

message will also be sent. To stop the alarm sounding, simply disarm

the system.

- 5 -

Download from Www.Somanuals.com. All Manuals Search And Download.

System Overview (cont'd)

Cross Zoning

Cross zoning is used to prevent false alarms. Up to 10 zones can be linked

together in your security system (programmed by the installer). If any of

the 10 linked zones faults in the armed state, the system will wait to see

if a second zone faults within a programmed period of time. When the

second zone faults, alarms will be sent out for both zones (if

programmed), the alarm bell will sound, and the two zones in alarm will

be displayed on the keypad.

However, if another fault does NOT occur within the programmed period

of time, only a Trouble report will be sent to the monitoring station and

no message will be displayed on the keypad until the system is disarmed.

Memory of Alarm

When an alarm condition occurs, the keypad displays the number(s)

of the zone(s) that caused the problem, and displays the type of alarm

(e.g.,

). It remains displayed until it is cleared by

F IRE ALARM

disarming the system (see the

section).

Disa r m in g a n d Silen cin g Ala r m s

Phone Access & Voice Response Capability

Your system may include a voice module that permits you to access

the system via a TouchTone phone, either on-premises or by call-in

when away. The phone access feature will enable you to do the

following:

Receive synthesized voice messages over the telephone regarding

the status of the security system.

•

Arm and disarm the system and perform most function commands

via the telephone, with voice confirmation provided after each

command entry.

•

Paging Feature

If the paging feature has been programmed for your system, your

pager will respond to certain conditions as they occur in your system.

Your pager will display code numbers indicating the type of condition

that has occurred. Refer to the

detailed information.

section for more

P a gin g Fea tu r e

- 6 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Entry/Exit delays

General Information

The FA148C has preset time delays, known as exit delay and entry

delay. Whenever you arm your system, exit delay gives you time to

leave through the designated exit door without setting off an alarm.

Exit delay begins immediately after entering any arming command,

and applies to all modes of arming protection. If it is programmed, a

slow beeping will sound throughout the exit delay period, with fast

beeps during the last 10 seconds.

gives you time to disarm the system when you re-enter

En tr y Dela y

through the designated entrance door. But you must disarm the

system before the entry delay period ends, or an alarm will occur. The

keypad beeps during the entry delay period, reminding you to disarm

the system. There are two entry delays (if programmed). The first is

for your primary entrance and the second can be used for a secondary

entrance, where a longer delay is required to give you enough time to

walk to the keypad to disarm the system.

You can also arm the system with no entry delay at all by using either

the INSTANT or MAXIMUM arming mode. These modes provide

greater security while you are on the premises.

See your installer for your delay times (you may want to record them

below).

Exit delay :

seconds

Entry delay 1:

Entry delay 2:

seconds

- 7 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Entry/Exit delay (cont'd)

Exit Alarms

To minimize false alarms sent to the alarm monitoring company,

your system may have been programmed for this feature. Ask

your installer if Exit Alarm is active for your system.

Exit Alarm Active

Whenever you arm the system, the exit delay begins. If an entry/exit

door or interior zone is faulted when the exit delay ends (e.g., exit

door left open), the system sounds an alarm and starts the entry delay

timer. If you disarm the system before the entry delay ends, the alarm

sound stops and the message

CANCE LE D ALAR M

displayed on the keypad, along with a zone number indicating the

faulted zone. No message is sent to the alarm monitoring company.

To clear the exit alarm condition, the open zone must be made intact.

To clear the display, enter your 4-digit security code plus OFF key.

If you do not disarm the system before the entry delay ends, and an

entry/exit door or interior zone is still open, the alarm sound

continues and an exit alarm message is sent to the alarm monitoring

company. The message

is displayed on the

E A

EXIT ALARM

keypad, along with a zone number indicating the faulted zone. To stop

the alarm, the system must be disarmed (by entering your code plus

OFF). To clear the display, enter your code plus OFF a second time.

An exit alarm also results if an entry/exit door or interior zone is

faulted within 2 minutes after the end of the exit delay.

- 8 -

Download from Www.Somanuals.com. All Manuals Search And Download.

About the Keypads

IMPORTANT

If the keypad beeps rapidly when you enter the premises, it

means that an alarm has occurred during your absence and an

intruder may still be on the premises.

LEAVE IMMEDIATELY AND CONTACT THE POLICE from a

nearby safe location.

General Information

Your keypads allow you to control all system functions. The keypads

feature a telephone-style (digital) keypad and a Liquid Crystal

Display (LCD) that shows the nature and location of all occurrences.

The keypads contain a built-in loudspeaker (sounder) that will

annunciate during alarms and troubles. The keypads also beep during

certain system functions, such as during entry/exit delay times, in

mode, and when you depress any of the keys (to acknowledge

CHIME

the key press).

There are two basic types of keypads: the

keypad and the

fixed -w or d

keypad (both described below).

a lp h a

Two-Line Alpha Keypad

Two-line alpha keypads feature a 2-line, 32-character alphanumeric

LCD that display system messages in English. The typical alpha

keypad (FA560KP) is shown on page 12. These keypads can also be

programmed with custom zone descriptors.

Th e scr een d isp la ys

d ep icted in th is m a n u a l a r e th ose th a t typ ica lly a p p ea r on a 2-

lin e a lp h a k eyp a d .

Fixed-Word Keypad

Fixed-word keypads are functionally identical to alpha keypads, but

the LCD display uses predesignated words to identify the nature and

location of occurrences. The typical fixed-word keypad (FA215KP) is

shown on the next page.

- 9 -

Download from Www.Somanuals.com. All Manuals Search And Download.

About the Keypads (cont'd)

AWAY

STAY

INSTANT

NO AC

CHIME

BAT

ALARM

CHECK

FIRE NIGHT

BYPASS CANCELED

NOT READY

ARMED

READY

FA215

FA215KP

FIXED-WORD KEYPAD

All burglary zones, interior

and perimeter, are armed.

AWAY:

STAY:

AWAY

STAY

INSTANT

NO AC

CHIME

BAT

CANCELED

Perimeter burglary zones,

such as protected windows

and doors, are armed.

ALARM

CHECK

FIRE

BYPASS

NIGHT

NOT READY

NIGHT & STAY:

(NIGHT-STAY)

Perimeter burglary zones

such as protected windows

and doors are armed, as well

as selected interior zones.

FIXED-WORD

KEYPAD DISPLAY

Perimeter burglary zones are

INSTANT:

armed and Entry Delay is turned off.

AWAY & INSTANT:

(MAXIMUM)

All burglary zones, interior and perimeter, are armed, and

Entry Delay is turned off.

One or more burglary protection zones have been bypassed.

BYPASS:

The burglary portion of the system is not ready for arming

(due to open protection zones).

NOT READY:

The burglary system is ready to be armed.

READY:

- 10 -

Download from Www.Somanuals.com. All Manuals Search And Download.

About the Keypads (cont'd)

NO AC:

AC power has been cut off. System is operating on backup

battery power.

AC:

CHIME:

BAT:

AC power is present.

The Chime feature is activated.

There is a low-battery condition in a wireless sensor (if

zone number is displayed) or a low system battery (if no

zone number is displayed).

ALARM:

CHECK:

An intrusion has been detected and the system is armed

(also appears during a fire alarm or audible emergency

alarm). The protection zone in alarm is also displayed.

A malfunction has been discovered in the system (at any

time); or an open has been detected in a Fire zone (at any

time); or a fault has been detected in a Day/Night burglary

zone (during a disarmed period). The zone number in

trouble is also displayed.

This message will be displayed if a hardwired zone is

shorted (if the Hardwire Short Detection option is enabled).

Ask your installer for details.

FIRE:

A fire alarm is present. The zone in alarm is also displayed.

CANCELED:

Appears when an alarm occurs and the system is disarmed

before the monitoring station has been notified.

- 11 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Functions of the Keypads

ARMED

READY

FA560

FA560KP 2-LINE ALPHA KEYPAD

F ixed -w or d k eyp a d s a r e fu n ct ion a lly sim ila r , excep t for scr een d isp la ys.

Fixed-word

DISP LAY WINDOW:

Completely arms

AWAY KEY:

both perimeter

burglary zones

and 2-line Alpha Displays use

Liquid Crystal Displays (LCDs) to

display protection point identifica-

tion and system status. 2-Line

Alpha keypads also may display

messages and user instructions.

and

for

interior

backup

protection by sensing an intruder's

movements

interior

through

areas. Also

protected

guards

protected doors, windows, etc.

Entrance can be made through an

entry delay zone without causing

an alarm if the system is disarmed

before the entry delay time

expires.

Disarms the

burglary portion of the system,

silences alarms and audible

trouble indicators, and clears

visual alarm trouble after the

problem has been corrected.

OF F

KEY:

- 12 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Functions of the Keypads (cont'd)

Arms the perimeter

Removes

STAY KEY:

BYP ASS

KEY:

burglary

sensors,

guarding

individual protection zones from

being monitored by the system.

protected doors, windows, and other

perimeter protection points, and

sounds an alarm if one is opened.

Interior protection is not armed,

which allows movement within your

house without causing an alarm.

Entrance can be made through an

entry delay zone without causing an

alarm if the system is disarmed

before the entry delay time expires.

If this key is pressed twice in rapid

succession, the system is armed in a

higher level of security than STAY

arming. This higher level is called

NIGHT-STAY and incorporates all

the features of the STAY mode, but

also arms selected interior zones

(ask your installer for further

information).

Displays

protection zones.

currently

bypassed

Arms in

KEY:

INSTANT

manner similar to STAY mode, but

turns off the entry delay period,

offering greater security while you

are inside and not expecting any

late visitors. An alarm will occur

immediately upon opening any

perimeter

including entry delay zones.

protection

point,

Allows the entry of

CODE KEY:

additional user codes that can be

given to other users of the system.

10.

Turns the CHIME

CHIME KEY:

Arms in a manner

KEY:

MAX

mode on and off. When it is on, any

entry through a protected delay or

perimeter zone while the system is

disarmed will cause a tone to sound

at the keypad(s).

similar to AWAY mode, but

eliminates the entry delay period,

thus

providing

maximum

protection. An alarm will occur

immediately upon opening any

protection point, including entry

delay zones.

11.

When this key is

R E ADY KEY:

depressed prior to arming the

system, the keypad will display all

open protection zones within the

keypad's home partition.

Tests the system

and alarm sounder.

TEST

KEY:

- 13 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Functions of the Keypads (cont'd)

Source of

audible internal warning and

confirmation sounds, as well as

16.

INTE R NAL SOUNDE R :

12.

Permits arming of the

KEY:

entering a security

system without

code (“Quick Arm,” if programmed).

Also used to view the second line of

single-line alpha keypads.

alarms (see

Su m m a r y of Au d ible

section).

Notifica tion

These keys may be

17.

A-B-C KE YS:

used as PANIC keys, if Quick Arm

Used to enter your

individual security access code(s).

13.

14.

KE YS 0-9:

(

✱21) is not enabled, or as Arming

Quick Arm

keys if

is enabled.

P OWE R /R E ADY

INDICATOR :

Keypads without this option use key

pairs to activate panic alarms. Refer

On keypads with a "Power" LED,

primary power is on when this is lit.

If the indicator is off, system is

operating on backup battery power.

On keypads with a "READY" LED,

system is ready to be armed if this

indicator is lit. An unlit indicator

means the system is not ready (a

zone is open).

section

P a n ic Keys a n d Ar m in g

for descriptions of these keys.

The key, when available, is

typically programmed to send a

special message to a Pager. Refer to

the

section for

P a gin g Fea tu r e

details.

(RED) Lit

15.

AR ME D INDICATOR :

IMP ORTANT!

when the system has been armed in

the STAY, NIGHT-STAY, AWAY,

INSTANT, or MAXIMUM mode.

When you use the keypad to enter codes and

commands, press the keys within 2 seconds of

one another. If 2 seconds elapse without a key

depression, the entry is aborted and must be

repeated from its beginning.

- 14 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Checking for Open Zones

Using the ✱ Key

Before arming your system, all protected doors, windows, and other

protection zones must be closed or bypassed (see Byp a ssin g

P r otection Zon es section). Otherwise the keypad will display a

NOT

message. Pressing the [✱] key will display all zones that are

R E ADY

faulted, making it easier for you to secure any open zones.

A green READY indicator (if present) on the keypad will be

lit if the system is ready to be armed. If it is not lit, the

system is not ready.

NOTE :

NOT READY - PRESS ✱

TO SHOW FAULTS

Sh ow fa u lted zon es.

✱

Press the [✱] key. (There is no need to

enter your security code in order to reveal

faulted zones.)

FAULT 05 FRONT

UPSTAIRS BEDROOM

Secu r e fa u lted zon es.

Typical fault display shows open zone.

Secure or bypass the zone(s) displayed

before arming the system.

***DISARMED***

READY TO ARM

Ar m th e system .

The

message is displayed when

R E ADY

all protection zones have been either

closed or bypassed.

You may now arm the system as

described on the following pages.

- 15 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Arming Perimeter Only

(with Entry Delay ON)

Using the

Key

STAY

Use this key when you are staying home, but expect someone to use

the entrance door later.

When armed in STAY mode, the system will sound an alarm if a

protected door or window is opened, but you may otherwise move

freely throughout the premises. Late visitors can enter through the

entrance door without causing an alarm, but they must disarm the

system within the entry delay period or an alarm will occur.

Close a ll p r otected p er im eter w in d ow s a n d d oor s b efor e

(see Ch eckin g for Open Zon es section). The green READY

a r m in g

indicator (if present) on the keypad should be lit if the system is ready

to be armed.

En ter 4-d igit secu r ity cod e, th en p r ess

th e STAY k ey.

(Security Code) STAY

Example: Press 7

6 , then

or , for q u i ck a r m i n g

(i f en a b l ed ):

P r ess th e [#] k ey follow ed by th e

STAY k ey, or p r ess a n d h old th e [B]

b u tton ( if a va ila b le).

Listen for 3 beep s.

The keypad beeps three times and

ARMED ***STAY***

You may exit now

displays the

message. The

ARMED STAY

red ARMED indicator also lights.

The portion of the

message disappears when the exit delay

time expires.

You m a y exit n ow

ARMED ***STAY***

You can restart the exit delay at any time after arming in STAY mode

by pressing the key. This is useful if you wish to open the

✴

entry/exit door to let someone in or out after arming the system

without having to disarm the system and then re-arm it again*.

* Refer to the note at bottom of page 19 dealing with the automatic Exit Restart feature.

- 16 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Arming Perimeter and Selected Interior Zones

(with Entry Delay ON)

Using the

Key to Arm Night-Stay

STAY

Use this key when you are staying home, but would like increased

security by arming preselected interior zones.

When armed in NIGHT-STAY mode, the system will sound an alarm if a

protected window or door is opened, or if one of the selected interior zones

is faulted. You may re-enter through the entrance door without causing

an alarm

one of the selected perimeter zones is not faulted, but the

system must be disarmed within the entry delay period or an alarm will

occur.

Close a ll p r otected p er im eter w in d ow s a n d d oor s b efor e a r m in g

(see Ch eck for Op en Zon es section). The green READY indicator on the

keypad should be lit if the system is ready to be armed.

En ter 4-d igit secu r ity cod e, th en

p r ess STAY k ey tw ice.

Example: Press

(Security Code)

STAY

, then

P r ess th e [#] k ey follow ed by th e

or , for q u i ck a r m i n g

(i f en a b l ed ):

STAY k ey tw ice,

p r ess a n d h old

(if available).

th e [C] b u tton

Listen for 3 beep s.

***NIGHT-STAY***

You may exit now

The keypad beeps three times and

displays the

message.

NIGH T-STAY

The

portion of the

You m a y exit n ow

message disappears when the exit

delay time expires.

You can restart the exit delay at any time after arming in STAY mode by

pressing the ✴ key. This is useful if you wish to open the entry/exit door

to let someone in or out after arming the system without having to

disarm the system and then re-arm it again*.

Refer to the note at bottom of page 19 dealing with the automatic Exit Restart feature.

- 17 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Arming Perimeter Only

(with Entry Delay OFF)

Using the

Key

INSTANT

Use this key when you are staying home and do not expect anyone to

use the entrance door.

When armed in INSTANT mode, the system will sound an alarm if a

protected door or window is opened, but you may otherwise move

freely throughout the premises. The alarm will also sound

immediately if anyone opens the entrance door.

p er im eter w in d ow s a n d d oor s b efor e a r m in g

Close a ll p r otected

(see Ch eckin g for

Op en Zon es section). The green READY indicator (if present) on the

keypad should be lit if the system is ready to be armed.

En ter 4-d igit secu r ity cod e, th en p r ess

th e INSTANT k ey.

(Security Code) INSTANT

Example: Press 7

6 , then

or , for q u i ck a r m i n g

(i f en a b l ed ):

P r ess th e [#] k ey follow ed b y th e

INSTANT k ey.

Listen for 3 beep s.

The keypad beeps three times and displays the

ARMED * INSTANT*

You may exit now

message. The red ARMED

ARMED INSTANT

indicator also lights.

You can restart the exit delay at any time after arming in INSTANT

mode by pressing the ✴ key. This is useful if you wish to open the

entry/exit door to let someone in or out after arming the system

without having to disarm the system and then re-arm it again.

* Refer to the note at bottom of page 19 dealing with the automatic Exit Restart

feature.

- 18 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Arming All Protection

(with Entry Delay ON)

Using the

Key

AWAY

Use this key when no one will be staying on the premises.

When armed in AWAY mode, the system will sound an alarm if a protected

door or window is opened, or if any movement is detected inside the premises.

You may leave through the entrance door during the exit delay period

without causing an alarm. You may also re-enter through the entrance door,

but must disarm the system within the entry delay period or else an alarm

will occur*.

If the Auto Stay feature is enabled (ask your installer) and the system

NOTE:

is armed from a hard-wired keypad, and no entry/exit zone is violated during

the exit time, the system to the STAY mode.

w ill r ever t

Close a ll p r otected p er im eter w in d ow s a n d d oor s b efor e a r m in g

(see

Ch eckin g for Open Zon es section). The green READY indicator (if present)

on the keypad should be lit if the system is ready to be armed.

E n ter 4-d igit secu r ity cod e, th en p r ess th e

AWAY k ey.

(Security Code)

AWAY

Example: Press 7

6 , then

or , for q u i ck a r m i n g

(i f en a b l ed ):

P r ess th e [#] k ey follow ed by th e AWAY

or (if

k ey

p r ess a n d h old th e [A] b u tton

available).

Listen .

ARMED***AWAY***

You may exit now

The keypad beeps twice, or beeps continuously

if Exit Warning has been programmed for your

system, and displays the

ARMED AWAY

message.

lights.

The red ARMED indicator also

The

portion of the

You m a y exit n ow

message disappears when the exit delay time

expires.

There is an automatic Exit Restart feature built into your system. It works

* NOTE:

this way: If you realize that you forgot something and have to go back inside the

premises (within the original exit delay time), as soon as you re-enter, a new exit

delay time sequence is started. This restarting of the exit delay time occurs only once

during each arming session, however; therefore you're permitted only one return

without setting off alarms.

- 19 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Arming All Protection

(With Entry Delay OFF)

Using the

Key

MAXIMUM

Use this key when the premises will be vacant for an extended period

of time, such as during a vacation, or when no one will be moving

through protected interior areas.

When armed in MAXIMUM mode, the system will sound an alarm if a

protected door or window is opened, or if any movement is detected

inside the premises. You may leave through the entrance door during

the exit delay period without causing an alarm, but an alarm will be

sounded as soon as someone re-enters.

Close a ll p r otected p er im eter w in d ow s a n d d oor s b efor e

(see Ch eckin g for Open Zon es section). The green READY

a r m in g

indicator (if present) on the keypad should be lit if the system is ready

to be armed.

En ter 4-d igit secu r ity cod e, th en

p r ess th e MAXIMUM k ey.

(Security Code) MAXIMUM

Example: Press 7

6 then

or , for q u i ck a r m i n g

(i f en a b l ed ):

P r ess th e [#] k ey follow ed by th e

MAXIMUM k ey

Listen .

ARMED *MAXIMUM*

You may exit now

The keypad beeps twice, or beeps

continuously if exit warning has been

programmed for your system, and

displays

the

ARMED

MAXIMUM

message (

on fixed-word

AWAY/INSTANT

keypads). The red ARMED indicator also

lights.

The

portion of the

You m a y exit n ow

message disappears when the exit delay

expires*.

* Refer to the note at bottom of page 19 dealing with the automatic Exit Restart feature.

- 20 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Disarming and Silencing Alarms

Using the 1 Key

OFF

Use the

key to disarm the system and to silence alarm and

OF F

trouble sounds. See Su m m a r y of Au d ible Notifica tion section for

information to help you distinguish between fire and burglary alarm

sounds.

If you return and the main burglary

IMP ORTANT:

sounder is on,

enter the premises, but call the

DO NOT

police from a nearby safe location. If you return after an

alarm has occurred and the main sounder has shut

itself off, the keypad will beep rapidly when you enter,

indicating that an alarm has occurred during your

absence and an intruder may still be on the premises.

and

LE AVE IMMEDIATELY

P OLICE

CONTACT THE

from a nearby safe location.

To d isa r m th e system a n d silen ce bu r gla r y a la r m s:

En ter 4-d igit secu r ity cod e, th en

p r ess th e OF F k ey.

(Security Code) OFF

Example: Press 7

6 then

Listen for 1 beep .

The keypad displays the

****DISARMED****

READY TO ARM

READY TO

message (if no alarms have occurred

ARM

while armed) and beeps once to confirm

that the system is disarmed.

- 21 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Disarming and Silencing Alarms (cont'd)

Memory of Alarm

If an alarm occurs, the keypad displays the zone number(s) that

caused the alarm and the type of alarm. These messages remain

displayed until cleared by a user.

To clea r th e d isp la y:

Note the zone number displayed and enter an OFF sequence.

En ter 4-d igit secu r ity cod e, th en

p r ess th e OF F k ey.*

(Security Code)

OFF

Example: Press 7

6 then 1 *

If the

message will not display, go to the displayed zone and

R E ADY

correct the fault (close windows, etc.). If the fault cannot be corrected,

notify your alarm company.

* In cases of an alarm, trouble, or

message, the 4-digit

CH E CK

security code and OFF key must be entered into the system two times

to clear the display.

- 22 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Bypassing Protection Zones

Using the

Key

BYPASS

This key is used when you want to arm your system with one or more

zones intentionally unprotected. Bypassed zones are unprotected and

will not cause an alarm when violated while your system is armed.

All byp a sses a r e r em oved w h en a n OF F sequ en ce (secu r ity

. Bypasses are also removed if the

cod e p lu s OF F ) is p er for m ed

arming procedure that follows the bypass command is not successful.

The system will not allow fire zones to be bypassed.

To byp a ss zon es, th e system m u st be d isa r m ed fir st.

En ter 4-d igit secu r ity cod e, th en

p r ess th e BYP ASS k ey.

(Security Code) BYPASS

Example: Press 7

6 then

En ter zon e n u m ber s.

Enter the zone number(s) for the zones to

be bypassed (e.g., 01, 02, 03, etc.).

(Zone Numbers)

All single-digit numbers must

Im p or ta n t!

be preceded by a zero (for example, enter

01 for zone 1).

3. BYPASS 07 FRONT

Wa it.

UPSTAIRS BEDROOM

The keypad displays the word

BYP ASS

Typical bypass message

along with each bypassed zone number

(and a zone descriptor if programmed).

Wait for these zones to be displayed, to be

sure that intended zones are bypassed.

4. DISARMED BYPASS

Ar m a s u su a l.

Arm the system as usual when the keypad

READY TO ARM

displays the

message.

READY TO ARM

- 23 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Bypassing Protection Zones (cont'd)

Quick Bypass

Your system may allow you to easily bypass all open (faulted) zones

without having to enter zone numbers individually. Ask your installer

if this feature is active.

En ter 4-d igit secu r ity cod e, th en

p r ess th e BYP ASS k ey.

(Security Code) BYPASS

Example: Press 7

6 then

2. BYPASS 07 FRONT

Wa it.

UPSTAIRS BEDROOM

In a few moments, all open zones are

displayed along with the word

Typical bypass message

BYP ASS

Wait for these zones to be displayed before

arming. Arming the system before zones

are displayed eliminates all bypasses.

3. DISARMED BYPASS

Ar m a s u su a l.

Arm the system as usual when the keypad

Ready to Arm

displays the

message.

R E ADY

Displaying Bypassed Zones

For determining what zones have been bypassed, all bypassed zones

can be displayed only when the system is disarmed, and when the

message shown in step 3 above is displayed.

BYP ASS

En ter 4-d igit secu r ity cod e, th en

p r ess th e BYP ASS k ey.

(Security Code) BYPASS

Example: Press 7

6 then

2. BYPASS 07 FRONT

Wa it.

UPSTAIRS BEDROOM

In a few moments, all open zones are

sequentially displayed along with the

Typical bypass message

word

BYP ASS

- 24 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Chime Mode

Using the 9 Key

CHIME

Your system can be set to alert you to the opening of a door or window†

while it is disarmed by using CHIME mode. When activated, three beeps

sound at the keypad whenever a protected perimeter door or window is

opened.

† Or selected doors or windows if chime-by-zone feature is active. Ask the

installer if this feature applies to your system.

Pressing the

✱

key will display the open protection points.

Note that the CHIME mode can be activated only when the system is

disarmed.

To tu r n CHIME m od e on :

En ter 4-d igit secu r ity cod e, th en p r ess

th e CHIME k ey.

(Security Code) CHIME

Example: Press 7

6 then

DISARMED CHIME

Ready to Arm

View .

The

message displays while CHIME

CHIME

mode is on.

To tu r n CHIME m od e off:

En ter 4-d igit secu r ity cod e, th en p r ess

th e CHIME k ey.

(Security Code) CHIME

Example: Press 7

6 then

****DISARMED****

READY TO ARM

View .

The

message disappears

DISARM CHIME

from the display.

- 25 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Panic Keys

(For Manually Activating Silent and/or Audible Alarms)

Using Panic Keys

Your installer may have programmed your system to use special keys

to manually activate panic functions. The functions that might be

programmed are listed below. See your installer for the function(s)

that are programmed for your system.

ACTIVE PANIC FUNCTIONS

KEYS

1 and ✱

3 and #

✱ and #

ZONE

FUNCTION

To use a paired-key panic function, simply press both keys of the

assigned pair at the same time. If your keypad has lettered keys for

panic functions, press the designated key and hold it down for at least

2 seconds to activate the panic function.

Types of Panic Alarms

A silen t em er gen cy

sends an alarm signal to the alarm monitoring

company,* but there are no audible alarms or visual displays.

sends an emergency message to the alarm

An a u d ible em er gen cy

monitoring company* and sounds a loud, steady alarm at your keypad

and at any external sounders that are connected. (

zone number are also displayed).

plus a

ALARM

alarm sends an emergency message to the

A p er son a l em er gen cy

alarm monitoring company* and sounds at keypads, but not at

external sounders ( plus a zone number are also displayed).

ALARM

sends a fire alarm message to the alarm monitoring

A fir e a la r m

company* and uniquely activates keypad and external sounders

plus a zone number are also displayed).

(

F IRE

*If your system is connected to an alarm monitoring company

- 26 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Using Device Commands

General Information

Your system may be set up so that certain lights or other devices can

be turned on or off by using the device command from the keypad.

Ask your installer if this has been done in your system.

programmed for your system, some devices may activate

automatically upon certain system conditions. In this case, the

following commands can be used to override the device activation. See

your installer for a full explanation of this feature.

To Activate Devices

En ter secu r ity cod e, th en p r ess # + 7 + d evice n u m ber .

(Security Code)

(Device Number)

Example: Press 7

then press , then press , then enter

the number representing the device you wish to activate. See your

installer for device numbers assigned for your system.

To Deactivate Devices

En ter secu r ity cod e, th en p r ess # + 8 + d evice n u m ber .

(Security Code)

(Device Number)

Example: Press 7

then press , then press , then enter

the number representing the device you wish to deactivate. See your

installer for device numbers assigned for your system.

Device

Device #/Description

- 27 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Paging Feature

General Information

If the Paging feature has been programmed for your system, your

pager will respond to certain conditions as they occur in your system.

This message appears in a 7-digit format explained below. You can

also send up to 16 additional digits that may consist of PIN numbers,

messages, reminders, etc. These 16 digits are programmed by your

installer and will appear before the standard 7-digit message.

The [D] button, when pressed (if available), sends a special message

to a pager and displays

on the keypad for 30 seconds

P a ger Msg sen t

(on an alpha keypad). The message it sends is coded as 999-9999 and

signifies ANY message the user and recipient have decided is

appropriate.

Code Format

The 7-digit condition code that follows takes the following form:

SSS-

00E E

SSS = 3-digit event code: 911 = Alarm

811 = Trouble

101 = Opening (disarm)

102 = Closing (arm AWAY)

00EE = The first 2 digits will always be 00. They are followed by the

2-digit user number or zone number, depending on the event

code.

Examples

Pager displays: 911–0004

This indicates that your system is

and

reporting an alarm (911) due to a fault in zone 4 (04).

Ala r m

codes are always followed by the zone numbers in which they

tr ou b le

occur.

Pager displays: 101–0011

reporting an open (101) by user 11 (0011).

This indicates that your system is

and

Op en in g

closin g

codes are always followed by the code number of the person who

caused it to happen. User codes are individually assigned and

programmed into the system by your installer.

- 28 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Security Codes

General Information

As an additional safety feature, other users who do not need to know

your code can be assigned different security codes. These secondary

users are identified by "user numbers," which you select when you

assign a user's security code. You can assign up to 14 additional user

codes (user numbers 03-16), including the Temporary and Duress

codes. Note that the master (primary) user of the system is the only

one who can assign codes to secondary (or temporary) users, and is

user number 02; user number 01 is reserved for the installer of the

system.

All codes can be used interchangeably when performing system

functions (a system armed with one user's code can be disarmed by

another user's code), except the temporary code, described below.

Temporary Code

This code can be used to arm and disarm the system. It is typically

assigned to someone (such as a babysitter) who needs to arm/disarm

the system only at certain times. The temporary code is assigned to

user 15. The user of this code should

use the Quick Arming

n ot

feature described below. This code will automatically be removed

when the Master code is entered.

Duress Code

This feature is intended for use when you are forced to disarm or arm

the system under threat. When used, the system will operate

normally, but can silently notify the alarm monitoring company of

your situation, if that service has been provided. Duress code is

assigned to user 16.

This code is useful only when the system is connected to

Im p or ta n t:

an alarm monitoring company.

- 29 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Security Codes (cont’d)

Quick Arming

Note that if Quick Arming was programmed by the installer, you can

press the key in place of the security code when arming the

use the security code to disarm the system,

system. You must

however.

a lw a ys

To Add a User or Change a User's Code

Important: Temporary users of the system (e.g., babysitter, cleaning staff)

should not be shown how to use any system function they do not need to know,

such as bypassing protection zones.

You must make sequential key depressions for all steps in a

procedure within 2 seconds of one another (e.g., perform steps 1, 2,

and 3 below with no delay between steps), or else the entire entry is

aborted and must be repeated from its beginning.

En ter 4-d igit Ma ster cod e, th en p r ess

k ey.

th e

(Master Code)

Example: Press 2

9 then

En ter u ser n u m ber .

Enter the 2-digit user number (03-16) for

the user you are adding or changing.

(User Number)

(User's Code)

En ter u ser 's cod e.

Enter the new 4-digit security code for

that user.

Changing the Master Code

Follow the procedure for changing a user's code, but enter user 02.

Additionally, when changing the Master code, you must perform step

3 twice with the same user code entry so that the new Master code

will be accepted by the system.

- 30 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Security Codes (cont'd)

To Delete a User

En ter 4-d igit Ma ster cod e, th en p r ess

k ey.

th e

(Master Code)

Example: Press 2

9 then

En ter u ser n u m ber .

Enter the 2-digit user number (03-16) for

the user whose code you are deleting.

(User Number)

3. -----------

Stop .

Wait (about 3 seconds) until the keypad

beeps once before pressing any other key.

The code is automatically deleted.

- 31 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Testing the System

(To be conducted weekly)

Using the

Key

TEST

The TEST key puts your system into a TEST mode, which allows each

protection point to be checked for proper operation. The keypad

sounds a single beep every 30 seconds as a reminder that the system

is in this TEST mode.

An alarm message will not be sent to your alarm monitoring

NOTE :

company during the following tests.

**** DISARM****

READY TO ARM

Disa r m th e system .

Disarm the system and close all protected

windows, doors, etc. The

message

R E ADY

should be displayed and the green READY

indicator (if present on the keypad) should

also be lit.

En ter 4-d igit secu r ity cod e, th en p r ess

TEST k ey.

(Security Code)

TEST

Example: Press 7

6 then

Listen .

The external sounder should sound for 2

seconds and then turn off.

If the sounder does not sound,

CALL F OR

SERVICE IMMEDIATELY

F a u lt zon es.

Open each protected door and window in

turn and listen for three beeps from the

keypad. Identification of each faulted

protection point should appear on the

display. The display will clear when the

door or window is closed.

- 32 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Testing the System (cont'd)

Walk in front of any interior motion

detectors (if used) and listen for three

beeps. The keypad should display the

identification of the detector when the

detector is activated. The display will clear

when no motion is detected. Note that if

you are using wireless motion detectors,

there is

3-minute delay between

activations. This is to conserve battery life.

To test all smoke detectors, follow the

manufacturer's instructions. The keypad

should display the identification of each

detector when each is activated.

If you experience a problem with any

protection point (no confirming sounds, no

display),

IMMEDIATELY.

CALL

F OR

SERVICE

When you have checked (and closed, where

necessary) all protection points, no zone

identification numbers should be displayed

on the keypad.

When you complete testing, exit the TEST

mode by continuing with step 5.

Exit TEST m od e.

Enter your security code and press the

OFF key.

(Security Code) OFF

If you inadvertently leave the test mode

active, it automatically turns off after

approximately 4 hours.

- 33 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Trouble Conditions

Typical Check Displays

The word

on the keypad's display, accompanied by a rapid

CH E CK

beeping at the keypad, indicates a trouble condition in the system.

The displays in parentheses in the left column below may appear on

non-alpha keypads when the associated trouble condition is present.

for “check” conditions, press any key.

To silen ce th e beep in g sou n d

+ Zone

Indicates that a problem exists with those

zone(s)*. First, determine why the zone(s)

displayed are faulted (open window or door;

open or shorted zone terminals; etc.) and

correct the problem. If the zone(s) contain a

wireless detector, check that changes in the

room (moving furniture, televisions, etc.) are

not blocking wireless signals to/from the

detector. If the problem has been corrected, the

CH E CK

Descriptors

zone descriptor(s) and

should dis-

CH E CK

appear from the keypad display. If not, key an

OFF sequence (enter the 4-digit security code,

then press the OFF key) to clear the display. A

“Check” condition can also indicate a wiring

problem (opens or shorts, for instance). If the

display persists,

CH E CK

SERVICE IMMEDIATELY.

CALL F OR

Note that the system will not allow arming if a

“Check” condition exists. To arm the system

with a “Check” condition present, you must

first bypass the zone(s) having the “Check”

condition.

Zone 9 represents a problem with

NOTE :

wireless receivers or other system devices,

which are not user-serviceable. CALL F OR

SERVICE IMMEDIATELY.

- 34 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Trouble Conditions (cont'd)

Telco F a u lt

(or

If the telephone line monitor feature has been

programmed for your system, this display

indicates that the telephone line has been

disconnected or cut. In some systems, this

display is accompanied by a trouble sound from

the keypad and an external sounder.

CONTACT YOUR SE R VICE COMP ANY

and

CH E CK

zone

)

IMMEDIATELY

To silence the trouble sound, enter your

security code plus OFF.

COMM. F AILURE Indicates that a failure has occurred in the

(or

)

F C

telephone communication portion of your

system.

CALL F OR SERVICE IMMEDI-

ATE LY.

SYSTEM LO BAT

(or with no

Indicates that a low system battery condition

exists, and is accompanied by a once-per-

BAT

zone no.)

minute beeping* at the keypad.

CALL F OR

SERVICE IMMEDIATELY.

You can stop the beeping that accompanies a low-

battery display by entering an OFF sequence

(security code + OFF).

zone

Indicates that a low-battery condition exists in

the wireless transmitter** displayed, and is

accompanied by a once-per-minute beeping at

LO BAT +

descriptor (or

with zone no.)

BAT

the

keypad.

CALL

F OR

SERVICE

IMMEDIATELY.

Not all systems use wireless transmitters.

MODEM COMM

(or

Indicates that the control is on-line with the

central station's remote computer. The control

will not operate while on-line. Wait a few

minutes. The display should disappear.

)

- 35 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Trouble Conditions (cont’d)

indicator

(if present) is off.

The system is operating on battery power only.

If only some lights are out on the premises,

check circuit breakers and fuses and reset or

P OWER

AC LOSS

displayed.

replace as necessary.

CALL F OR SERVICE

if AC power cannot be

IMMEDIATELY

restored to the system.

Bu sy-Sta n d by

(or

If this remains displayed for more than 1

)

d I

minute, system is disabled.

CALL F OR

SE R VICE AT ONCE .

OP E N CIR CUIT

(or

The keypad is not receiving signals from the

control.

)

Lon g Rn g Tr b l

(or

CALL F OR SE R VICE AT ONCE .

If programmed, backup Long Range Radio

)

b F

communication has failed.

CALL F OR

SE R VICE AT ONCE .

Bell fa ilu r e

(or

Bell/Siren supervision failure.

SE R VICE AT ONCE .

CALL F OR

)

CHE CK 70

RF J a m

(or

If enabled and a Receiver J am is detected, a

report will be sent to the monitoring station

)

Ch eck 90

and at the same time a

message

Rcvr J a m

will toggle with the present display on the

alpha keypad. When the jam condition is

cleared, a Restore message is sent to the

monitoring station. To clear the keypad

display, enter your 4-digit code and

key.

OFF

- 36 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Fire Alarm System

(If Installed)

General Information

Your fire alarm system (if installed) is active 24 hours a day,

providing continuous protection. In the event of an emergency, the

installed smoke and heat detectors will automatically activate your

security system, triggering a loud, interrupted sound from the

keypad. Optional exterior sounders will also produce an interrupted

sound. Your keypad will display a

message (with zone location)

F IRE

until you silence and clear the alarm display.

In Case of Fire

1. Should you become aware of a fire emergency before your detectors

sense the problem, go to your nearest keypad and press the single

panic key (or panic key pair) assigned as FIRE emergency (if

programmed by the installer) and hold it down for at least 2

seconds. The alarm will sound.

2. Evacuate all occupants from the premises.

3. If flames and/or smoke are present, leave the premises and notify

your local fire department immediately.

4. If no flames or smoke are apparent, investigate the cause of the

alarm. The keypad will display the zone descriptor of the zone(s) in

an alarm condition.

Silencing a Fire Alarm

1. Silence the alarm by pressing the

key.

OFF

To clear the alarm display, enter your security code and press the

key again.

OFF

- 37 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Fire Alarm System (cont’d)

2. If the keypad indicates a trouble condition after the second OFF

sequence, check smoke detectors to see if they are responding to

smoke or heat-producing objects in their vicinity. Should this be

the case, eliminate the source of heat or smoke.

3. If this does not remedy the problem, there may still be smoke in

the detector. Clear it by fanning the detector for about 30 seconds.

4. When the problem has been corrected, clear the display by entering

your code and pressing the

key.

OFF

- 38 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Recommendations for Proper Protection

THE F OLLOWING RECOMMENDATIONS F OR THE LOCATION OF F IRE

AND BUR GLAR Y DE TE CTION DE VICE S H E LP P R OVIDE P R OP E R

COVE R AGE F OR THE P R OTE CTE D P R E MISE S.

Recommendations for Smoke and Heat Detectors

With regard to the number and placement of smoke/heat detectors,

we subscribe to the recommendations contained in the National Fire

Protection Association's (NFPA) Standard #72, noted below.

Early-warning fire detection is best achieved by the installation

of fire detection equipment in all rooms and areas of the

household as follows: For minimum protection, a smoke detector

should be installed outside of each separate sleeping area, and

on each additional floor of a multi-floor family living unit,

including basements. The installation of smoke detectors in

kitchens, attics (finished or unfinished), or in garages is not

normally recommended.

For additional protection, the NFPA recommends that you install

heat or smoke detectors in the living room, dining room, bedroom(s),

kitchen, hallway(s), attic, furnace room, utility and storage rooms,

basements, and attached garages.

- 39 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Recommendations for Proper Protection (cont’d)

✪

▲

✪

KITCHEN

▲

✪

KITCHEN

BDRM

DINING

BEDROOM

TV ROOM

DINING

■

BDRM

LIVING ROOM

■

✪

■

✪

BEDROOM

LIVING ROOM

✪

▲

Smoke Detectors for Minimum Protection

Smoke Detectors for Additional Protection

Heat-Activated Detectors

■

✪

▲

■

BEDROOM

■

✪

BEDROOM

✪

BEDROOM

▲

■

▲

KTCHN

GARAGE

CLOSED

DOOR

LVNG RM

■

BASEMENT

In a d d ition , w e r ecom m en d th e follow in g:

• Install a smoke detector inside every bedroom where a smoker

sleeps.

• Install a smoke detector inside every bedroom where someone

sleeps with the door partly or completely closed. Smoke could be

blocked by the closed door. Also, an alarm in the hallway outside

may not wake up the sleeper if the door is closed.

• Install

smoke detector inside bedrooms where electrical

appliances (such as portable heaters, air conditioners, or

humidifiers) are used.

• Install a smoke detector at both ends of a hallway if the hallway is

more than 40 feet (12 meters) long.

• Install smoke detectors in any room where an alarm control is

located, or in any room where alarm control connections to an AC

source or phone lines are made. If detectors are not so located, a fire

within the room could prevent the control from reporting a fire or

an intrusion.

- 40 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Recommendations for Proper Protection (cont'd)

Recommendations for Proper Intrusion Protection

For proper intrusion coverage, sensors should be located at every

possible point of entry to a home or commercial premises. This

includes skylights and upper windows in a multi-level building.

In addition, we recommend that radio backup be used in a security

system so that alarm signals can still be sent to the alarm monitoring

station in the event that the telephone lines are out of order (alarm

signals are normally sent over the phone lines, if connected to an

alarm monitoring station).

- 41 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Emergency Evacuation

Establish and regularly practice a plan of escape in the event of fire. The following

steps are recommended by the National Fire Protection Association:

1. Position your detector or your interior and/or exterior

OOM

sounders so that they can be heard by all occupants.

CLOSET

BEDR

2. Determine two means of escape from each room. One

OOM

BEDR

path of escape should lead to the door that permits

normal exit from the building. The other should be

an alternative route, such as a window, should your

primary escape path be impassable. Station an

escape ladder at such windows if there is a long drop

to the ground.

BEDR

2^NDFLOOR

OOM

KITCHEN

BEDR

BACK DOOR

OOM

3. Sketch a floor plan of the building. Show windows,

doors, stairs, and rooftops that can be used to escape.

Indicate escape routes for each room. Keep these

routes free from obstruction and post copies of the

escape routes in every room.

BEDR

1^STFLOOR

•

4. Assure that all bedroom doors are shut while you are

asleep. This will prevent deadly smoke from entering

while you escape.

•

BACK

5. To determine which escape path to use during a fire,

first feel the door. If it is hot, check your alternate

escape route. If the door is cool, open it cautiously. Be

prepared to slam the door if smoke or heat rushes in.

•

6. Where smoke is present, crawl on the floor; do not

walk upright. Smoke rises and may overcome you.

Clearer air is near the floor.

FRONT

7. Escape quickly; don't panic.

8. Establish a common meeting place outdoors, away from your house, where

everyone can meet and then take steps to contact the authorities and account for

those missing. Choose someone to assure that nobody returns to the house —

many die going back.

- 42 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Maintaining Your System

Taking Care of Your System

The components of your security system are designed to be as

maintenance-free as possible. However, to make sure that your

system is in reliable working condition:

1. Test your system weekly.

2. Test your system after any alarm occurs (see Testin g th e System

section).

Replacing Batteries in Wireless Sensors

Each wireless sensor in your system has a 9-volt or 3-volt battery. The

system detects a low battery in any wireless sensor, including smoke

detectors, the optional personal emergency transmitter, and the

optional portable wireless keypad. (The system detects a low battery

in a portable wireless keypad as soon as one of its keys is pressed, and

Wireless

sensors may

not have

been

installed in

your security

system.

responds be displaying

on the wired keypad.)

Alkaline batteries provide a minimum of 1 year of operation, and in

most units and applications, provide 2–4 years of service. Three-volt

lithium batteries provide up to 4 or more years of operation. Actual

battery life depends on the environment in which the sensor is used,

the number of signals that the transmitter in the sensor has to send,

and the specific type of sensor. Factors such as humidity, high or low

temperatures, or large swings in temperature may all lead to the

reduction of actual battery life in an installation.

If you have a low battery in a wireless sensor, the keypad displays a

message. In addition, a battery-operated smoke

LOW BATTERY

detector with

low battery emits

single "chirp" sound

approximately once every 20–30 seconds, identifying itself as the

smoke detector with the weak battery.

The

message comes on as a warning that

LOW BATTE RY

NOTE :

battery replacement in the indicated sensor(s) is due within 30 days.

In the meantime, the sensor causing the low-battery indication is still

fully operational.

- 43 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Maintaining Your System (cont’d)

Use only batteries recommended by your installer as

Im p or ta n t:

replacement.

Silencing Low Battery Warning Tones at the Keypad

You can silence the keypad’s warning tones by pressing the

key,

OFF

but the keypad's

message display will remain on as

LOW BATTE RY

a reminder that you have a low-battery condition in one or more of

your sensors. When you replace the weak battery with a fresh one, the

sensor will send a "good battery" signal to the control as soon as the

sensor is activated (opening/closing of door, window, etc.), causing the

display to turn off. If the sensor is not activated, the

LOW BATTE RY

display will automatically clear within approximately 1 hour.

Routine Care

Treat the components of your security system as you would any

other electrical equipment. Do not slam sensor-protected doors or

windows.

•

Keep dust from accumulating on the keypad and all protective

sensors, particularly on motion sensors and smoke detectors.

•

The keypad and sensors should be cleaned carefully with a dry soft

cloth. Do n ot sp r a y wa ter or a n y oth er flu id on th e u n its.

- 44 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Quick Guide to System Functions

FUNCTION

PROCEDURE

COMMENTS

Check Zones

Do this to view faulted zones when system is

not ready.

Press [✴]

Arm System

Enter code or press #

Do this to arm the system in the mode

selected.

Press arming key desired

(AWAY, NIGHT-STAY*, STAY,

INSTANT, MAXIMUM)

* Press STAY twice in rapid

succession to arm NIGHT-STAY

Disarm System

Bypass Zones

Enter code

Do this to disarm the system and silence

alarms.

Press OFF [1]

Enter code

Press [6]

Do this to bypass protection zones. Bypassed

zones are unprotected and will not cause an

Enter zone numbers to be bypassed alarm if violated.

(use 2-digit entries)

Quick Bypass

Enter code

Do this to bypass all faulted zones

Press [6] and stop

automatically, if programmed.

Chime Mode ON Enter code

Press CHIME [9]

Do this to turn on CHIME mode. Keypad

will sound if doors or windows are violated

while system is disarmed.

Chime Mode OFF Enter code

Press CHIME [9]

Do this to turn CHIME mode off.

Test Mode ON

Enter code

Press [5]

Do this to enter TEST mode. Sounds alarm

sounder and allows sensors to be tested.

Test Mode OFF

Enter code

Press OFF [1]

Do this to turn TEST mode off. System returns

to normal mode.

Add or Change a Enter Master code

Do this to add or change a user code.

User

Press [8] key

Enter user's 2-digit user no.

Enter code for that user

Delete a User

Enter Master code

Press [8] key

Enter user number to be deleted

Do this to delete a user code from the system.

Do this to change the existing Master code.

Change a Master Enter Master code

Code

Press [8] key

Press [0] + [2] (master user no.)

Enter new 4-digit Master code

Enter new Master code again

- 45 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Summary of Audible Notification

(Alpha Display Keypads)

SOUND

CAUSE

DISPLAY

FIRE ALARM

FIRE is displayed; descriptor of zone in alarm is

displayed.

LOUD, INTERRUPTED*

Keypad & External

BURGLARY/AUDIBLE

EMERGENCY ALARM

ALARM is displayed; descriptor of zone in alarm is

also displayed.

LOUD, CONTINUOUS*

Keypad & External

a. SYSTEM DISARM

a. SYSTEM READY is displayed.

ONE SHORT BEEP

(not repeated)

b. SYSTEM ARMING ATTEMPT

WITH AN OPEN ZONE

b. The number and descriptor of the open protection

zone is displayed.

Keypad only

c. BYPASS VERIFY

c. Numbers and descriptors of the bypassed

protection zones are displayed (one beep is

heard for each zone displayed). Subsequently,

the following is displayed: ZONE BYPASSED

SYSTEM READY.

SYSTEM IS IN TEST MODE

Opened zone identifications will appear.

ONE SHORT BEEP

(once every 40 seconds)

Keypad only

LOW BATTERY AT A

TRANSMITTER

LO BAT displayed with description of transmitter.

ONE BEEP

(once every 40 seconds)

Keypad only

ARM AWAY OR MAXIMUM

ARMED AWAY or ARMED MAXIMUM displayed.

Red ARMED indicator lit.

TWO SHORT BEEPS

Keypad only

a. ARM STAY, NIGHT-STAY, OR

INSTANT

a. ARMED STAY or ARMED INSTANT displayed.

Red ARMED indicator lit.

THREE SHORT

BEEPS

b. CHIME displayed, descriptor of open protection

zone displayed if the [✱] key is pressed.

Keypad only

b. ZONE OPENED WHILE

SYSTEM IS IN CHIME MODE

a. TROUBLE

a. CHECK displayed; descriptor of troubled

protection zone is displayed.

RAPID BEEPING

Keypad only

b. FIRE or ALARM is displayed; descriptor of zone

in alarm is displayed.

b. MEMORY OF ALARM

c. BELL FAILURE or CHECK 70 is displayed.

d. SYSTEM LO BAT or BAT is displayed.

c. BELL FAILURE

d. SYSTEM LOW BATTERY

e. ARMED AWAY or ARMED MAXIMUM is

displayed along with You may exit now.

e. LAST 10 SECONDS OF EXIT

DELAY

a. EXIT DELAY WARNING (if

programmed)

a. ARMED AWAY or ARMED MAXIMUM is

displayed along with You may exit now.

SLOW BEEPING

Keypad only

b. ENTRY DELAY WARNING

b. DISARM SYSTEM OR ALARM WILL OCCUR is

displayed.

Exceeding the delay time without disarming

causes alarm.

* If a bell is used as external sounder, fire alarm is pulsed ring; burglary/audible emergency is steady ring.

- 46 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Glossary

The following terms are used throughout the manual.

"Armed" simply means that the burglary portion of your system

is turned ON and is in a state of readiness. "Disarmed" means

that the burglary system is turned OFF, and must be re-armed

to become operational. However, even in a "disarmed" state,

"emergency" and "fire" portions of your system are still

operational.

ARM/DISARM:

This is the area on your keypad containing numbered

pushbuttons similar to those on telephones or calculators. These

keys control the arming and disarming of the system, and

perform other functions described in this manual.

KEYPAD:

A specific area of protection.

ZONE:

To disarm a specific area of burglary protection while leaving

other areas operational.

BYPASS:

An area of protection containing doors most frequently used to

enter or exit (typically, a front door, back door, or door from the

garage into the building). The delay zone allows sufficient time

for authorized entry or exit without causing an alarm. Consult

your installer for the entry and exit delay times that have been

set for your system during installation, and record them in the

space provided in “Entry/exit delays.”

DELAY ZONE:

An area of protection whose violation causes a trouble indication

during the disarmed (DAY) mode and an alarm during the

armed (NIGHT) mode.

DAY/NIGHT ZONE:

- 47 -

Download from Www.Somanuals.com. All Manuals Search And Download.

UL NOTICE: This is a "GRADE A" system.

FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 15 STATEMENT

This equipment has been tested to FCC requirements and has been found acceptable for use. The

FCC requires the following statement for your information:

This equipment generates and uses radio frequency energy and if not installed and used properly,

that is, in strict accordance with the manufacturer's instructions, may cause interference to radio

and television reception. It has been type tested and found to comply with the limits for a Class B

computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed

to provide reasonable protection against such interference in a residential installation. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment

does cause interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• If using an indoor antenna, have a quality outdoor antenna installed.

• Re-orient the receiving antenna until interference is reduced or eliminated.

• Move the receiver away from the control/communicator.

• Move the antenna leads away from any wire runs to the control/communicator.

• Plug the control/communicator into a different outlet so that it and the receiver are on different

branch circuits.

If necessary, the user should consult the dealer or an experienced radio/television technician for

additional suggestions.

The user or installer may find the following booklet prepared by the Federal Communications

Commission helpful: "Interference Handbook." This booklet is available from the U.S. Government

Printing Office, Washington, DC 20402.

The user shall not make any changes or modifications to the equipment unless authorized by the

Installation Instructions or User's Manual. Unauthorized changes or modifications could void the

user's authority to operate the equipment.

IN THE EVENT OF TELEPHONE OPERATIONAL PROBLEMS

In the event of telephone operational problems, disconnect the control by removing the plug from the

RJ 31X (CA38A in Canada) telephone wall jack. We recommend that your certified installer

demonstrate disconnecting the phones on installation of the system. Do not disconnect the phone

connection inside the control/communicator. Doing so will result in the loss of your phone lines. If the

regular phone works correctly after the control/communicator has been disconnected from the phone

lines, the control/communicator has

problem and should be returned for repair. If, upon

disconnection of the control/communicator, there is still a problem on the line, notify the telephone

company that they have a problem and request prompt repair service. The user may not under any

circumstances (in or out of warranty) attempt any service or repairs to the system. It must be returned

to the factory or an authorized service agency for all repairs.

- 48 -

Download from Www.Somanuals.com. All Manuals Search And Download.

FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 68 NOTICE

This equipment complies with Part 68 of the FCC rules. On the front cover of this

equipment is a label that contains, among other information, the FCC registration number

and ringer equivalence number (REN) for this equipment. If requested, this information

must be provided to the telephone company.

This equipment uses the following jacks:

An RJ 31X is used to connect this equipment to the telephone network.

The REN is used to determine the quantity of devices which may be connected to the

telephone line. Excessive RENs on the telephone line may result in the devices not ringing

in response to an incoming call. In most, but not all areas, the sum of the RENs should not

exceed five (5.0). To be certain of the number of devices that may be connected to the line,

as determined by the total RENs, contact the telephone company to determine the

maximum REN for the calling area.

If this equipment causes harm to the telephone network, the telephone company will notify

you in advance that temporary discontinuance of service may be required. If advance notice

is not practical, the telephone company will notify the customer as soon as possible. Also,

you will be advised of your right to file a complaint with the FCC if you believe necessary.

The telephone company may make changes in its facilities, equipment, operations, or

procedures that could affect the operation of the equipment. If this happens, the telephone

company will provide advance notice in order for you to make the necessary modifications

in order to maintain uninterrupted service.

If trouble is experienced with this equipment, please contact the manufacturer for repair

and warranty information. If the trouble is causing harm to the telephone network, the

telephone company may request you remove the equipment from the network until the

problem is resolved.

There are no user serviceable components in this product, and all necessary repairs must

be made by the manufacturer. Other repair methods may invalidate the FCC registration

on this product.

This equipment cannot be used on telephone company-provided coin service. Connection to

Party Line Service is subject to state tariffs.

This equipment is hearing-aid compatible.

When programming or making test calls to an emergency number, briefly explain to the

dispatcher the reason for the call. Perform such activities in the off-peak hours; such as

early morning or late evening.

- 49 -

Download from Www.Somanuals.com. All Manuals Search And Download.

WARNING!

THE LIMITATIONS OF THIS ALARM SYSTEM

While this system is an advanced design security system, it does not offer guaranteed protection

against burglary or fire or other emergency. Any alarm system, whether commercial or residential, is

subject to compromise or failure to warn for a variety of reasons. For example:

• Intruders may gain access through unprotected openings or have the technical sophistication to

bypass an alarm sensor or disconnect an alarm warning device.

• Intrusion detectors (e.g., passive infrared detectors), smoke detectors, and many other sensing

devices will not work without power. Battery-operated devices will not work without batteries,

with dead batteries, or if the batteries are not put in properly. Devices powered solely by AC will

not work if their AC power supply is cut off for any reason, however briefly.

• Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the

alarm receiver. Even if the signal path has been recently checked during a weekly test, blockage

can occur if a metal object is moved into the path.

• A user may not be able to reach a panic or emergency button quickly enough.

• While smoke detectors have played a key role in reducing residential fire deaths in the United

States, they may not activate or provide early warning for a variety of reasons in as many as 35%

of all fires, according to data published by the Federal Emergency Management Agency. Some of

the reasons smoke detectors used in conjunction with this System may not work are as follows.

Smoke detectors may have been improperly installed and positioned. Smoke detectors may not

sense fires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or

roofs, or on the other side of closed doors. Smoke detectors also may not sense a fire on another

level of a residence or building. A second-floor detector, for example, may not sense a first-floor or

basement fire. Moreover, smoke detectors have sensing limitations. No smoke detector can sense

every kind of fire every time. In general, detectors may not always warn about fires caused by

carelessness and safety hazards like smoking in bed, violent explosions, escaping gas, improper

storage of flammable materials, overloaded electrical circuits, children playing with matches, or

arson. Depending upon the nature of the fire and/or the locations of the smoke detectors, the

detector, even if it operates as anticipated, may not provide sufficient warning to allow all

occupants to escape in time to prevent injury or death.

• Passive Infrared Motion Detectors can detect intrusion only within the designed ranges as

diagrammed in their installation manual. Passive Infrared Detectors do not provide volumetric

area protection. They do create multiple beams of protection, and intrusion can only be detected in

unobstructed areas covered by those beams. They cannot detect motion or intrusion that takes

place behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or windows.

Mechanical tampering, masking, painting or spraying of any material on the mirrors, windows or

any part of the optical system can reduce their detection ability. Passive Infrared Detectors sense

changes in temperature; however, as the ambient temperature of protected area approaches the

temperature range of 90° to 105°F, the detection performance can decrease.

- 50 -

Download from Www.Somanuals.com. All Manuals Search And Download.

WARNING!

THE LIMITATIONS OF THIS ALARM SYSTEM (cont'd)

• Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if

they are located on the other side of closed or partly open doors. If warning devices sound on a

different level of the residence from the bedrooms, then they are less likely to waken or alert

people inside the bedrooms. Even persons who are awake may not hear the warning if the alarm is

muffled by a stereo, radio, air conditioner or other appliance, or by passing traffic. Finally, alarm

warning devices, however loud, may not warn hearing-impaired people or waken deep sleepers.

• Telephone lines needed to transmit alarm signals from a premises to a central monitoring station

may be out of service or temporarily out of service. Telephone lines are also subject to compromise

by sophisticated intruders.

• Even if the system responds to the emergency as intended, however, occupants may have

insufficient time to protect themselves from the emergency situation. In the case of a monitored

alarm system, authorities may not respond appropriately.

• This equipment, like other electrical devices, is subject to component failure. Even though this

equipment is designed to last as long as 10 years, the electronic components could fail at any time.

The most common cause of an alarm system not functioning when an intrusion or fire occurs is

inadequate maintenance. This alarm system should be tested weekly to make sure all sensors and

transmitters are working properly.

Installing an alarm system may make one eligible for lower insurance rates, but an alarm system is

not a substitute for insurance. Homeowners, property owners and renters should continue to act

prudently in protecting themselves and continue to insure their lives and property.

We continue to develop new and improved protection devices. Users of alarm systems owe it to

themselves and their loved ones to learn about these developments.

SE R VICING INF OR MATION

Your local First Alert Professional alarm dealer is the person best

qualified to service your alarm system. Arranging some kind of

regular service program with him is advisable.

Your local First Alert Professional alarm dealer is:

Name:

Address: ____________________________________________________

_____________________________________________________________

Phone:_______________________________________________________

- 51 -

Download from Www.Somanuals.com. All Manuals Search And Download.

CANADIAN DEPARTMENT OF COMMUNICATIONS (DOC)

STATEMENT

NOTICE

AVIS

The Canadian Department of Communications label

identifies certified equipment. This certification means that

the equipment meets certain telecommunications network

protective, operational and safety requirements. The

Department does not guarantee the equipment will

operate to the user's satisfaction.

L'étiquette du ministère des Communications du Canada

identifie le matériel homologué. Cette étiquette certifie que

le matériel est conforme à certaines normes de protection,

d'exploitation et de sécurité des réseaux de

télécommunications. Le ministère n'assure toutefois pas

que le matériel fonctionnera

l'utilisateur.

la satisfaction de

Before installing this equipment, users should ensure that

it is permissible to be connected to the facilities of the

local telecommunications company. The equipment must

also be installed using an acceptable method of

connection. In some cases, the company's inside wiring

associated with a single-line individual service may be

extended by means of certified connector assembly

(telephone extension cord). The customer should be

aware that compliance with the above conditions may not

prevent degradation of service in some situations.

Avant d'installer ce matériel, l'utilisateur doit s'assurer qu'il

est permis de le raccorder aux installations de l'entreprise

locale de télécommunications. Le matériel doit également

être installé en suivant une méthode acceptée de

raccordement. Dans certains cas, les fils intérieurs de

l'entreprise utilisés pour un service individuel à la ligne

unique peuvent être prolongés au moyen d'un dispositif

homologué de raccordement (cordon prolongateur

téléphonique interne). L'abonné ne doit pas oublier qu'il

est possible que la conformité aux conditions énoncées ci-

dessus n'empèchet pas la dégradation du service dans

certaines situations. Actuellement, les entreprises de

télécommunications ne permettent pas que l'on raccorde

leur matériel aux prises d'abonnés, sauf dans les cas

precis prévus par les tarifs particuliers de ces entreprises.

Repairs to certified equipment should be made by an

authorized Canadian maintenance facility designated by

the supplier. Any repairs or alterations made by the user

to this equipment, or equipment malfunctions, may give

the telecommunications company cause to request the

user to disconnect the equipment.

Les réparations du matériel homologué doivent être

effectuées pas un centre d'entretien canadien autorisé

désigné par le fournisseur. La compagnie de

Users should ensure for their own protection that the

electrical ground connections of the power utility,

telephone lines and internal metallic water pipe system, if

present, are connected together. This precaution may be

particularly important in rural areas.

télécommunications peut demander

l'utilisateur de

débrancher un appareil à la suite de réparations ou de

modifications effectuées par l'utilisateur ou à cause de

mauvais fonctionnement.

Caution:

Users should not attempt to make such

connections themselves, but should contact the

appropriate electric inspection authority, or electrician, as

appropriate.

Pour sa propre protection, l'utilisateur doit s'assurer que

tous les fils de mise en terre de la source d'énergie

électrique, des lignes téléphoniques de réseau de

conduites d'eau s'il y en a, soient raccordés ensemble.

Cette précaution est particulièrement importante dans les

régions rurales.

The Load Number (LN) assigned to each terminal device

denotes the percentage of the total load to be connected

to a telephone loop which is used by the device, to

prevent overloading. The termination on a loop may

consist of any combination of devices subject only to the

requirement that the total of the Load Numbers of all the

devices does not exceed 100.

Avertissement: L'utilisateur ne doit pas tenter de faire

ces raccordements lui-même il doit avoir recours à un

service d'inspection des installations électriques, ou à un

électricien, selon le cas.

L'indice de charge (IC) assigné

chaque dispositif

terminal pour éviter toute surcharge indique le

pourcentage de la charge totale qui peut être raccordé à

un circuit téléphonique bouclé utilisé par ce dispositif. La

terminaison du circuit bouclé peut être constituée de

n'importe quelle combinaison de dispositifs, pourvu que la

somme des indices de charge de l'ensemble des

dispositifs ne dépasse pas 100.

- 52 -

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S INSURANCE P REMIUM CREDIT REQUEST

This form should be completed and forwarded to your homeowner’s insurance carrier for possible

premium credit.

A. GE NE R AL INF OR MATION:

Insured’s Name and Address:

Insurance Company:

Policy No.:

Other ______________________________

F A148C

Type of Alarm:

Burglary

Fire

Both

Installed by:

Serviced by:

Name

Address

B. NOTIF IES (In ser t B = Bu r gla r y, F = F ir e)

Local Sounding Device

Police Dept.

Fire Dept.

Central Station

Name:

Address:

Phone:

A.C. With Rechargeable Power Supply

C. P OWERED BY:

D. TESTING:

Quarterly

Monthly

Weekly

Other

continued on other side

- 53 -

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S INSURANCE P REMIUM CREDIT REQUEST

E. SMOKE DETECTOR LOCATIONS

Furnace Room

Basement

Kitchen

Bedrooms

Attic

Hall

Living Room

Dining Room

F . BURGLARY DETECTING DEVICE LOCATIONS:

Front Door

Basement Door

All windows

Rear Door

All Exterior Doors

1^stFloor Windows

Interior locations

All Accessible Openings, Including Skylights, Air Conditioners and Vents

G. ADDITIONAL P ERTINENT INF ORMATION:

Signature:

Date:

- 54 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Index

AC Loss.....................................................36

Add a User.................................................30

Alarm .........................................................11

Alpha Keypad ..............................................9

Audible Emergency .......................11, 26, 46

Away......................................4, 5, 10, 19, 45

Away Mode................................................19

Babysitter Code.........................................29

Beeping .....................................7, 34, 35, 46

Burglary Protection..............4, 10, 12, 13, 47

Bypassing Zones.......................................23

Check ......................................15, 34, 45, 46

Chime ............................................25, 45, 46

Chime Mode ..................................13, 25, 45

Comm. Failure...........................................35

Delete a User.......................................31, 45

Disarming ............................................21, 47

Displaying Bypassed Zones......................24

Duress Code..............................................29

Emergency Evacuation..............................42

Entry Delay........7, 10, 16, 17, 18, 19, 20, 46

Exit Alarm ....................................................8

Exit Delay ................................16, 17, 18, 46

Fire Alarm......................................11, 26, 37

Fire Protection .............................................5

Fire Zone .............................................11, 23

Fixed Word Keypad...............................9, 12

Fixed Word Keypad Display ......................10

Instant..........................................................4

Key Functions............................................12

Keypads.................................................9, 12

Lo Bat ..................................................35, 46

Low Battery....................................11, 35, 43

Maximum ...............................................4, 20

Maximum Mode .........................................20

Memory of Alarm .............................6, 22, 46

Modem Comm ...........................................35

National Fire Protection Association....39, 42

Not Ready............................................15, 45

OFF............................................................23

Off Key...........................................21, 33, 35

Paging Feature ......................................6, 28

Panic Alarm ...............................................26

Panic Functions .........................................26

Panic Keys.................................................26

Personal Emergency ...........................26, 43

Quick Arming .........16, 17, 18, 19, 20, 29, 30

Security Codes ......................................5, 29

Silence Alarm.............................................21

Silent Emergency.......................................26

Sounder .................................6, 9, 14, 32, 35

Stay......................................4, 10, 16, 17, 45

System Overview.........................................4

Telco Fault.................................................35

Temporary Users.......................................30

Test Key.....................................................32

Test Mode............................................32, 45

Trouble Conditions.....................................34

Two-line Alpha Keypad................................9

User Number .......................................28, 29

Voice Module...............................................6

Wireless Sensor.........................................43

Zones...........................................................4

- 55 -

Download from Www.Somanuals.com. All Manuals Search And Download.

ONE YE AR LIMITE D WAR R ANTY

Pittway Corporation, and its divisions, subsidiaries and affiliates ("Seller"), 165 Eileen Way, Syosset, New York

11791, warrants its First Alert security equipment (the "product") to be free from defects in materials and

workmanship for one year from date of original purchase, under normal use and service. Seller's obligation is

limited to repairing or replacing, at its option, free of charge for parts, labor, or transportation, any product proven

to be defective in materials or workmanship under normal use and service. Seller shall have no obligation under

this warranty or otherwise if the product is altered or improperly repaired or serviced by anyone other than the

Seller. In case of defect, contact the security professional who installed and maintains your security equipment or

the Seller for product repair.

This one year Limited Warranty is in lieu of all other express warranties, obligations or liabilities. THERE ARE

NO EXPRESS WARRANTIES, WHICH EXTEND BEYOND THE FACE HEREOF. ANY IMPLIED WARRANTIES,

OBLIGATIONS OR LIABILITIES MADE BY SELLER IN CONNECTION WITH THIS PRODUCT, INCLUDING

ANY IMPLIED WARRANTY OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE OR

OTHERWISE, ARE LIMITED IN DURATION TO A PERIOD OF ONE YEAR FROM THE DATE OF ORIGINAL

PURCHASE. ANY ACTION FOR BREACH OF ANY WARRANTY, INCLUDING BUT NOT LIMITED TO ANY

IMPLIED WARRANTY OF MERCHANTABILITY, MUST BE BROUGHT WITHIN 12 MONTHS FROM DATE OF

ORIGINAL PURCHASE. IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL

OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED,

OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED

BY THE SELLER'S OWN NEGLIGENCE OR FAULT. Some states do not allow limitation on how long an implied

warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitation or

exclusion may not apply to you.

Seller does not represent that the product may not be compromised or circumvented; that the product will prevent

any personal injury or property loss by burglary, robbery, fire or otherwise; or that the product will in all cases pro-

vide adequate warning or protection. Buyer understands that a properly installed and maintained alarm may only

reduce the risk of a burglary, robbery, fire or other events occurring without providing an alarm, but it is not insur-

ance or a guarantee that such will not occur or that there will be no personal injury or property loss as a result.

CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJ URY, PROPERTY

DAMAGE OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING. HOWEVER,

IF SELLER IS HELD LIABLE, WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR DAMAGE

ARISING UNDER THIS LIMITED WARRANTY OR OTHERWISE, REGARDLESS OF CAUSE OR ORIGIN,

SELLER'S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE

PRODUCT, WHICH SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER. This

warranty gives you specific legal rights, and you may also have other rights which vary from state to state. No

increase or alteration, written or verbal, to this warranty is authorized.

175 Eileen Way, Syosset, New York 11791

¬.ꢀꢁꢂꢂ9ꢃFl

K4855V1 3/00

Download from Www.Somanuals.com. All Manuals Search And Download.

Cobra Electronics GPS Receiver GPS100 S User Manual
Dukane Projector 8934 User Manual
Dyson Carpet Cleaner PN201844 18 02 User Manual
Earthquake Sound Speaker Kompressor User Manual
Faber Ventilation Hood Perla User Manual
Fisher Price Computer Hardware K4073 User Manual
Frigidaire Clothes Dryer FFSG5115PA User Manual
Frigidaire Oven 318201532 User Manual
Fujitsu Telephone SRS 9924 ABM User Manual
GE Dishwasher PDWT400RBB User Manual