RAYZOR Q7™
user manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
CONTENTS
General Information
4
3
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
GENERAL INFORMATION
INTRODUCTION
Congratulations, you have just purchased one of the most innovative and reliable lighting
fixtures on the market today! The RAYZOR Q7™ has been designed to perform reliably
for years when the guidelines in this booklet are followed. Please read and understand
the instructions in this manual carefully and thoroughly before attempting to operate this
unit. These instructions contain important information regarding safety during use and
maintenance.
UNPACKING
Thank you for purchasing the RAYZOR Q7™ by Elation Professional®. Every RAYZOR
Q7™ has been thoroughly tested and has been shipped in perfect operating condition.
Carefully check the shipping carton for damage that may have occurred during shipping.
If the carton appears to be damaged, carefully inspect your unit for damage and be sure
all accessories necessary to operate the unit have arrived intact. In the event damage
has been found or parts are missing, please contact our customer support team for
further instructions. Please do not return this unit to your dealer without first contacting
customer support at the number listed below. Please do not discard the shipping carton
in the trash. Please recycle whenever possible.
BOX CONTENTS
• (1) powerCON Power Cable
• (1) 5-Pin XLR Cable
• (1) Omega Bracket (Holder)
• (1) Safety Cable
• Manual & Warranty Card
M A N U A L U P D A T E S
4
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
CUSTOMER SUPPORT
Elation Professional® provides a customer support line, to provide set up help and to
answer any question should you encounter problems during your set up or initial
comments or suggestions. For service related issues please contact Elation
Professional®. Service Hours are Monday through Friday 8:00 a.m. to 5:00 p.m. Pacific
Standard Time.
Voice: 323-582-3322
Fax: 323-832-9142
E-mail: [email protected]
WARRANTY REGISTRATION
The RAYZOR Q7™ carries a two year (730 days) limited warranty. Please fill out the
enclosed warranty card to validate your purchase. All returned service items whether
under warranty or not, must be freight pre-paid and accompany a return authorization
(R.A.) number. The R.A. number must be clearly written on the outside of the return
package. A brief description of the problem as well as the R.A. number must also be
written down on a piece of paper and included in the shipping container. If the unit is
under warranty, you must provide a copy of your proof of purchase invoice. Items
returned without a R.A. number clearly marked on the outside of the package will be
refused and returned at customer’s expense. You may obtain a R.A. number by
contacting customer support at 323-582-3322.
IMPORTANT NOTICE!
There are no user serviceable parts inside this unit. Do not attempt any repairs
yourself; doing so will void your manufactures warranty. Damages resulting from
modifications to this fixture and/or the disregard of safety and general user
instructions found in this user manual void the manufactures warranty and are
not subject to any warranty claims and/or repairs.
5
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
2-YEAR LIMITED WARRANTY
A. Elation Professional® hereby warrants, to the original purchaser, Elation Professional® products to be free
of manufacturing defects in material and workmanship for a period of two years, (730 days) from the date of
purchase. This warranty shall be valid only if the product is purchased within the United States of America,
including possessions and territories. It is the owner’s responsibility to establish the date and place of purchase
by acceptable evidence, at the time service is sought.
B. For warranty service, send the product only to the Elation Professional® factory. All shipping charges must
be pre-paid. If the requested repairs or service (including parts replacement) are within the terms of this
warranty, Elation Professional® will pay return shipping charges only to a designated point within the United
States. If the entire instrument is sent, it must be shipped in its original package. No accessories should be
shipped with the product. If any accessories are shipped with the product, Elation Professional® shall have no
liability what so ever for loss of or damage to any such accessories, nor for the safe return thereof.
C.
This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which Elation Professional® concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the Elation Professional® factory unless prior
written authorization was issued to purchaser by Elation Professional®; if the product is damaged because not
properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintenance, cleaning or periodic
check-up. During the period specified above, Elation Professional® will replace defective parts at its expense,
and will absorb all expenses for warranty service and repair labor by reason of defects in material or
workmanship. The sole responsibility of Elation Professional® under this warranty shall be limited to the
repair of the product, or replacement thereof, including parts, at the sole discretion of Elation Professional®. All
products covered by this warranty were manufactured after January 1, 1990, and bare identifying marks to that
effect.
E. Elation Professional® reserves the right to make changes in design and/or improvements upon its
products without any obligation to include these changes in any products theretofore manufactured.
F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made by
Elation Professional® in connection with this product, including warranties of merchantability or fitness, are
limited in duration to the warranty period set forth above. And no warranties, whether expressed or implied,
including warranties of merchantability or fitness, shall apply to this product after said period has expired. The
consumer’s and or Dealer’s sole remedy shall be such repair or replacement as is expressly provided above;
and under no circumstances shall Elation Professional® be liable for any loss or damage, direct or
consequential, arising out of the use of, or inability to use, this product.
G. This warranty is the only written warranty applicable to Elation Professional® Products and supersedes all
prior warranties and written descriptions of warranty terms and conditions heretofore published.
6
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
SAFETY INSTRUCTIONS
The RAYZOR Q7™ is an extremely sophisticated piece of electronic equipment.
To guarantee a smooth operation, it is important to follow the guidelines in this
manual. The manufacturer of this device will not accept responsibility for
damages resulting from the misuse of this fixture due to the disregard of the
information printed in this manual.
This device falls under PROTECTION CLASS 1. It’s essential this device is
grounded properly, and only qualified personnel perform all electrical connections.
•
•
For proper operation, follow the Installation guidelines described on page 11 of this manual. Only qualified
and certified personnel should perform installation of this fixture and only the original rigging parts
(brackets, holders, clamps, safety cables) included with this fixture should be used for installation. Any
modifications will void the original manufactures warranty and increase the risk of damage and/or personal
injury.
Never look directly into the light source of this fixture to prevent risk of injury to your retina, which may
induce blindness. Those suffering from EPILEPSY should avoid looking directly into the light source of this
unit at all times.
•
•
The fan and air inlets must remain clean and never blocked. Allow approx. 6” (15cm) between this fixture
and other devices or a wall for proper cooling.
Always disconnect from main power source before performing any type of service and/or cleaning
procedure. Only handle the power cord by the plug end, never pull out the plug by tugging the wire portion
of the cord.
•
Do not operate this fixture if the power cord has become frayed, crimped and/or damaged. If the power
cord is damaged, replace it immediately with a new one of similar power rating.
7
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
GENERAL GUIDELINES
• NEVER OPEN THIS FIXTURE WHILE IN USE!
• During the initial operation of this fixture, a light smoke or smell may emit from the
interior of the fixture. This is a normal process and is caused by excess paint in the
interior of the casing burning off from the heat associated with the lamp and will
decrease gradually over time.
• This fixture is a professional lighting effect designed for use on stage, in nightclubs,
theatres, etc. Do not attempt installation and/or operation without proper knowledge
of how to do so.
• Do not permit operation by persons who are not qualified for operating this type of
theatrical fixture. Most damages are the result of operations by nonprofessionals.
• If this fixture is exposed to extreme temperatures due to environmental changes, do
not power the fixture on until it has reached room temperature. Condensation could
damage the fixture.
• Consistent operational breaks may ensure the fixture will function properly for many
years to come.
• Do not shake fixture, avoid brute force when installing and/or operating the device.
• When choosing an installation location, please be sure this fixture will not be exposed
to extreme heat, moisture, and/or dust. The minimum distance between this fixture
and other devices or wall and/or flat surface should be at least 0.5 meter (1.5 ft).
• When using quick release “OMEGA” Cam-Lock system, be sure the four quick lock
fasteners are locked in the quick lock holes correctly.
• Always install the fixture with an appropriate safety cable. When installing the fixture
in a suspended environment, always use mounting hardware that is no less than M10
x 25 mm, also be sure the hardware is insert in the pre-arranged screw holes in the
base of the fixture.
• Please use the original packaging and materials to transport the fixture in for service.
8
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
FEATURES
The new Rayzor Q7™ features (7) 15W Quad Color RGBW LEDs with up to 100,000 hour
average life, high speed 16-bit resolution movement, color mixing, rainbow effect, 7° beam
and 13° field angles, 4 zone chase effects, 8 auto program chase effects, flicker free
operation for TV and Film, 5pin DMX connections, full color 180° reversible LCD menu
display with 6 button touch control panel with battery backup for menu display power, and a
multi-voltage universal auto switching power supply (100-240v). Optional accessories for the
Rayzor Q7™ include a snoot lens cover and diffusion filter holder.
FIXTURE OVERVIEW
1: LED Lens Assembly
2: DC Switch
3: Microphone
4: LCD Menu Control Display
5: MODE/ESC Button
6: ENTER Button
7: LEFT Button
8: DOWN Button
9: UP Button
10: RIGHT Button
11: 5-Pin DMX OUT
12: 5-Pin DMX IN
13: Power Switch
14: Fuse
15: Power IN
16: Power OUT
9
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
1. LED Assembly – RGBW Quad LEDs comprise the LED assembly.
2. DC Switch – Controls menu and display power when disconnected from main power.
3. Microphone – Captures external low frequency sounds to trigger the unit in Sound
Active mode. Designed to capture low frequency sounds only, tapping on the
microphone and/or high-pitched sounds may not trigger unit.
4. LCD Menu Control Display – Full color LCD animated menu display.
5. MODE/ESC Button – Used to access the menu functions and exit the current command.
6. ENTER Button – Used to enter into or lock a certain menu function.
7. LEFT Button – Used to toggle through the menu display.
8. DOWN Button – Used to toggle down or back through the menu functions and settings.
9. UP Button – Used to toggle forward through the menu functions and settings.
10.RIGHT Button – Used to toggle through the menu display.
11.5-Pin DMX IN – Accepts incoming DMX signal via a male 5-pin XLR jack.
12.5-Pin DMX OUT – Sends incoming DMX signal to the next fixture in the DMX chain via a
female 5-pin XLR jack.
13.Power Switch – Used to power the unit ON or OFF.
14.Fuse Holder Assembly – Houses 250v T3.13A GMA safety fuse. Always replace with
an exact match unless otherwise specified by an authorized Elation Service Technician.
Using a fuse other than that specified could seriously damage the unit and may void the
manufactures warranty.
15.Power IN – Power connection (powerCon) to power source
16.Power OUT – Power connection (powerCon) to daisy chain to another unit.
10
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
INSTALLATION
T he elec tric connection m ust onl y b e carried out b y a qu alified elec trician.
CAUTIONS
• Recommended ambient temperature for this fixture is between 14°F to 113°F
(-10°C to 45°C). Do not use the fixture under or above this temperature.
• For added protection, mount the fixture in areas outside walking paths, seating areas, or
in areas were unauthorized personnel might reach the fixture.
• Before mounting the fixture to any surface, make sure the installation area can hold a
minimum point load of 10 times the weight of the fixture. (46Kgs / 102 Lbs)
• Fixture installation must always be secured with a secondary safety attachment, such as
an appropriate safety cable.
• Never stand directly below the device when mounting, removing or servicing the fixture.
11
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
MOUNTING POINTS
• Overhead mounting requires extensive experience, including amongst others calculating
working load limits, installation material being used, and periodic safety inspection of all
installation material and the device. If you lack these qualifications, do not attempt the
installation yourself. Improper installation can result in bodily injury.
• Be sure the fixture is kept at least 0.5m (1.5 feet) away from any flammable materials
(decoration etc.).
12
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
SECURING
• Secure the clamp to the bracket using a M12 screw fitted through the Ф13 center hole.
• Insert the ¼ Turn Twist Locks of the first Omega bracket into the respective holes on the
bottom of the device. Tighten the Twist Locks a ¼ turn clockwise.
• Install the second Omega bracket on the top of the device in the same way.
• Pull a safety cable through the holes on the bottom of the base and over the trussing
system or a safe installation.
Notice: This step is very important to ensure the fixture will not drop out by the
damage of the clamp.
13
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
UNDERSTANDING DMX
DMX-512
DMX is short for Digital Multiplex. This is a universal protocol used by most lighting and
controller manufactures as a form of communication between intelligent fixtures and
controllers. DMX allows all makes and models of different manufactures to be linked
together and operate from a single controller. This is possible as long as all the fixtures and
the controller are DMX compliant. A DMX controller sends the DMX data instructions to the
fixture allowing the user to control the different aspects of an intelligent light. DMX data is
sent out as serial data that travels from fixture to fixture via data “IN” and data “OUT” XLR
terminals located on the fixtures (most controllers will only have output jacks).
DMX LINKING
To ensure proper DMX data transmission, always use proper DMX cables and a terminator.
When using several DMX fixtures try to use the shortest cable path possible. Never split a
DMX line with a “Y” style connector. The order in which the fixtures are connected in a DMX
line does not influence the DMX addressing. For example; a fixture assigned a starting DMX
address of 1 may be placed anywhere in the DMX chain, at the beginning, at the end, or
anywhere in the middle. The DMX controller knows to send data assigned to address 1 to
that fixture no matter where it is located in the DMX chain. The RAYZOR Q7™ can be
controlled via DMX-512 protocol. The RAYZOR Q7™ is a 64-channel DMX fixture. The
DMX address is set electronically using the controls on the LCD menu.
DATA CABLE (DMX Cable) REQUIREMENTS (For DMX and Master/Slave Operation)
Your fixture and your DMX controller require a standard 3-pin or 5-pin XLR connector for
data input and data output (see figure below). If you are making your own cables, be sure to
use two conductor, shielded digital DMX cable rated at 120 ohms; this cable is designed for
DMX transmission and may be purchased from your Elation dealer or at most professional
lighting retailers. Your cables should be made with a male and female XLR connector on
either end of the cable. Also, remember that a DMX line must be daisy chained and cannot
be split, unless using an approved DMX splitter such as the Elation Opto Branch 4™ or DMX
Branch/4™.
14
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
Be sure to follow the above figure when making your own cables. Do not use
the ground lug on the XLR connector. Do not connect the cable’s shield
conductor to the ground lug or allow the shield conductor to come in contact
with the XLR outer casing. Grounding the shield could cause a short circuit
and erratic behavior.
DMX-512 CONTROLLER CONNECTION
Connect the provided XLR cable to the female 3-pin XLR output of your controller and the
other side to the male 3-pin XLR input of the RAYZOR Q7™ (Please refer to the diagram
below.). You can chain multiple panels together through serial linking. The cable that should
be used is two conductor, shielded DMX cable with XLR input and output connectors.
Always be sure daisy chain your in and out data connections, never split or “Y” your DMX
connections unless you are using an approved DMX splitter such as the Elation Opto Branch
4™ or DMX Branch/4™.
Address 35
Address 18
Address 1
15
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
DMX-512 CONNECTION WITH DMX TERMINATOR
A DMX terminator should be used in all DMX lines especially in longer runs. The use of a
terminator may avoid erratic behavior in your DMX line. A terminator is a 120 ohm 1/4 watt
resistor that is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This fixture is inserted in the female XLR connector of the last fixture in your daisy
chain to terminate the line. Using a line terminator (Elation part: DMX T PACK) will decrease
the possibilities of erratic behavior.
5-Pin XLR DMX CONNECTORS
Some manufactures use 5-pin XLR connectors for DATA transmission in place of 3-pin.
5-pin XLR fixtures may be implemented in a 3-pin XLR DMX line. When inserting standard
5-pin XLR connectors in to a 3-pin line a cable adaptor must be used, these adaptors are
readily available at most electric stores. The following chart details a proper cable
conversion.
16
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
DMX ADDRESSING
All fixtures should be given a DMX starting address when using a DMX controller, so the
correct fixture responds to the correct control signal. This digital starting address is the
channel number from which the fixture starts to “listen” to the digital control information sent
out from the DMX controller. The allocation of this starting DMX address is achieved by
setting the correct DMX address on the digital display located on the back of the fixture.
You can set the same starting address for all fixtures or a group of fixtures, or set different
address for each individual fixture. Be advised that setting all fixtures to the same DMX
address will subsequently control all fixtures in the same fashion, in other words, changing
the settings of one channel will affect all the fixtures simultaneously.
If you set each fixture to a different DMX address, each unit will start to “listen” to the
channel number you have set, based on the quantity of control channels (DMX channels) of
each fixture. That means changing the settings of one channel will only affect the selected
fixture.
In the case of the RAYZOR Q7™, when in Extended 29 Channel mode (default can also be
set to Basic 15 Channel and Standard 17 Channel modes), you should set the starting DMX
address of the first unit to 1, the second unit to 30 (29 + 1), the third unit to 59 (29 + 30), the
fourth unit to 88 (29 + 59) and so on.
Note: During start-up the RAYZOR Q7™ will automatically detect whether a DMX data
signal is being received or not. If DMX data signal is being received, the display will show
"Addr=XXX" (XXX representing the actual DMX address). If the fixture is not receiving a
DMX signal the display will flash. If your fixture is connected to a DMX controller and the
display is flashing (not receiving a DMX signal), please check the following:
-
The 3-PIN or 5-PIN XLR input plug (cable with DMX signal from controller) is not
connected or is not inserted completely into the DMX input jack of the fixture.
The DMX controller is switched off or defective.
-
-
-
The DMX cable or connector is defective.
A DMX terminator has been inserted into the last fixture in your DMX chain.
17
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
FIXTURE MENU
ON-BOARD SYSTEM MENU
The RAYZOR Q7™ comes with an easy to navigate system menu. The next section will
detail the functions of each command in the system menu.
LCD MENU CONTROL PANEL
The control panel (see image below) located on back of the fixture allows you to access the
main menu and make all necessary adjustments to the RAYZOR Q7™. During normal
operation, tapping the MODE/ESC button once will access the fixture’s main menu. Once in
the main menu you can navigate through the different functions and access the sub-menus
with the UP, DOWN, RIGHT, and LEFT buttons. Once you reach a field that requires
adjusting, tap the ENTER button to activate that field and use the UP and Down buttons to
adjust the field. Tapping the ENTER button once more will confirm your setting. You may
exit the main menu at any time without making any adjustments by tapping the MODE/ESC
button.
NOTE: To access the LCD Menu Control Display via the internal battery, press and hold the
DC SWITCH button for 2 seconds. The LCD Menu Control Display will shut OFF
automatically about 1 minute from the last button press. To shut OFF the LCD Menu Control
Display immediately, set "Reset Default" menu option to “ON” in the “Personality” menu
and tap ENTER button to confirm your selection.
18
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
*Default Settings Shaded
RAYZOR Q7™ SYSTEM MENU
Set DMX Address
DMX Value
A001~AXXX
DMX Address Setting
DMX Value Display
Slave Setting
ALL……
FUNCTION
Slave Mode
Slave1, Slave2, Slave3
Master / Alone
Master / Alone
Current Time
Auto Program
Sound Control
Auto Program
Music Control
XXXX(Hours)
XXXX(Hours)
Power On Running Time
Fixture Running Time
Fixture Last Times Clear
Timer Password 038
Clear Fixture Last time
Temperature In The Head
Software Version
Total Run Time
Last Run Time
Timer Password
Clear Last Run
Head Temperature
V1.0……
Time
XXXX(Hours)
Password=XXX
ON/OFF
Information
INFORMATION
Temperature Info
Software Version
Address via DMX ON/OFF
Address Via DMX
No DMX Status
Pan Reverse
Tilt Reverse
Pan Degree
Tilt Degree
Close/Hold/Auto/Music Auto Run If No DMX
ON/OFF
Pan Reverse Movement
Tilt Reverse Movement
Pan Degree Select 1, 2, 3
Tilt Degree Select 1, 2
Movement Feedback
Movement Mode Select
Sensitivity of Microphone
Stand By Mode
ON/OFF
630/540offset/540
270/240
Status Settings
Feedback
ON/OFF
Movement Speed Speed 1 ~ 4
Mic Sensitivity
Hibernation
Password
RDM PID
Auto
0-99%
OFF, 01M~99M, 15M
Password=XXX
xxxxxx
Service Password = 050
RDM PID Code
Service Setting
Fans Control
PERSONALITY
High
Fans Speed Select
Low
Shutoff Time
Flip Display
Key Lock
Display Flash
Celsius
02~60m 05m
ON/OFF
Display Shut Off Time
Display Reverse 180º
Key Lock
Display Setting
ON/OFF
ON/OFF
Display Flashes If No DMX
Temperature Switch
Between °C or °F
Temperature C/F
Initial Status
Fahrenheit
PAN =XXX
ON/OFF
Initial Effect Position
Reset Default
Restore Factory Settings
19
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
RESET
Reset All
Reset All Settings
FUNCTION
Reset Pan/Tilt
Reset Pan/Tilt Settings
Auto Program, PAN, PAN-Fine, TILT,
TILT-Fine, Move Speed, Strobe, Dimmer,
Red-1, Green-1, Blue-1, White-1, Red-2,
Green-2, Blue-2, White-2, Red-3, Green-3,
Blue-3, White-3, Red-4, Green-4, Blue-4,
White-4, Color Macro, Color Preset,
Test Channel
Test Functions
Color Mode, Chase Patter, Chase Speed
Auto Program, PAN, PAN-Fine, TILT,
TILT-Fine, Move Speed, Strobe, Dimmer,
Red-1, Green-1, Blue-1, White-1, Red-2,
Green-2, Blue-2, White-2, Red-3, Green-3,
Blue-3, White-3, Red-4, Green-4, Blue-4,
White-4, Color Macro, Color Preset,
EFFECT
ADJUST
Fine Adjustment of
Functions (0-255)
Manual Control
Color Mode, Chase Patter, Chase Speed
-Password-
PAN
Password=XXX
(0-255)
Password = 050
Calibration
User Mode
Fine Adjustment of PAN
Fine Adjustment of TILT
TILT
(0-255)
Stand Mode
Basic Mode
Extend Mode
User Mode A
User Mode B
User Mode C
Select DMX & User Modes
USER MODE
SETTING
Max Chanel, Auto Program, PAN,
PAN-Fine, TILT, TILT-Fine, Move Speed,
Strobe, Dimmer, Red-1, Green-1, Blue-1,
White-1, Red-2, Green-2, Blue-2, White-2,
Red-3, Green-3, Blue-3, White-3, Red-4,
Green-4, Blue-4, White-4, Color Macro,
Color Preset,
Edit User Mode A
Edit User Mode B
Edit User Mode C
Preset User Modes
Color Mode, Chase Patter, Chase Speed
20
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
Auto Pro Part1 = Program 1 ~ 10
Program 1
Auto Pro Part2 = Program 1 ~ 10
Program 2
Select Programs
To Be Run
Select Program
Edit Program
Auto Pro Part3 = Program 1 ~ 10
Program 3
Testing Program
Program In Loop
Save And Exit
Program 1 ~
Program 10
Pro. Test,
Step 01 – Step 64
Auto Program, PAN,
PAN-Fine, TILT,
TILT-Fine, Move
Speed, Strobe,
EDIT
PROGRAM
Dimmer,
Red (1-4), Green (1-4),
Blue 1-4), White (1-4),
Color Macro, Color
Preset, Color Mode,
Chase Patter, Chase
Speed, Fade Time,
Scene Time, Input By
Output
Save And Automatically
Return Manual
Scene 001 ~
Scene 125
Edit Scenes
Scenes Edit
Automatic Scenes
Recorder
Record Controller
XX~XX
FUNCTION - Set DMX Address
Adjust the desired DMX address via the Control Panel.
1. Tap MODE/ESC to access the main menu and tap ENTER.
2. Tap the UP/DOWN until “Set DMX Address” is displayed and tap ENTER.
3. Current DMX address is displayed (001-509), tap the UP/DOWN to select desired
DMX address (001-509) and ENTER to confirm selection.
4. Tap MODE/ESC to return to the main menu.
21
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
FUNCTION - DMX Value
Display the DMX 512 value of each channel.
1. Tap MODE/ESC to access the main menu and tap ENTER.
2. Tap UP/DOWN until “DMX Value” is displayed and tap ENTER.
3. Tap UP/DOWN to select desired “DMX Value” and ENTER to confirm selection.
4. Tap MODE/ESC to return the main menu.
FUNCTION - Slave Mode
Define the fixture as a slave.
1. Tap MODE/ESC to access the main menu and tap ENTER.
2. Tap UP/DOWN until “Slave Mode” is displayed and tap ENTER.
3. Tap UP/DOWN to select desired mode (“Slave1, Slave2, Slave3”) and tap
ENTER to confirm selection.
4. Tap MODE/ESC to return to the main menu.
FUNCTION - Auto Program
Define the fixture mode (“Master” or “Alone”) for running Auto Programs. Select
the desired internal programs under “Select Program”, set the number of steps
under “Edit Program”, and edit the individual scenes under “Edit Scenes”.
1． Tap MODE/ESC to access the main menu and tap ENTER.
2． Tap UP/DOWN until “Auto Program” is displayed and tap ENTER.
3． Tap UP/DOWN to select desired mode (“Master”,” Alone”) and tap ENTER to
confirm selection.
4． Tap MODE/ESC to return to the main menu.
FUNCTION – Sound Control
Define the fixture mode (“Master” or “Alone”) for running Auto Programs via
sound activation, default is Master.
1. Tap MODE/ESC to access the main menu and tap ENTER.
2. Tap UP/DOWN until “Sound Control” is displayed and tap ENTER.
3. Tap UP/DOWN to select desired mode (“Master” or “Alone”) and tap ENTER to
confirm selection.
4. Tap MODE/ESC to return to the main menu
22
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
INFORMATION - Time Information - Current Time
Display the run time of the fixture from last power ON.
The counter is reset after each time the device is powered OFF.
1． Tap MODE/ESC to access main menu, tap UP/DOWN/LEFT/RIGHT until
“Information” is highlighted and tap ENTER.
2． Tap UP/DOWN buttons until “Time Information” is displayed and tap ENTER.
3． Tap UP/DOWN until “Current Time” is displayed, tap ENTER and ”XXXXXh”
(Hours) is displayed.
4． Tap MODE/ESC to return to the main menu.
INFORMATION - Time Information - Total Run Time
Display the total running time of the fixture.
1. Tap MODE/ESC to access main menu, tap UP/DOWN/LEFT/RIGHT until
“Information” is highlighted and tap ENTER.
2. Tap UP/DOWN until “Time Information” is displayed and tap ENTER.
3. Tap UP/DOWN until “Total Run Time” is displayed, tap ENTER and “XXXXXh”
(Hours) is displayed.
4. Tap MODE/ESC to return to the main menu.
INFORMATION - Time Information - Last Run Time
Display last the running time of the lamp.
1. Tap MODE/ESC to access main menu, tap UP/DOWN/LEFT/RIGHT until
“Information” is highlighted and tap ENTER.
2. Tap UP/DOWN until “Time Information” is displayed and tap ENTER.
3. Tap UP/DOWN until “Last Run Time” is displayed, tap ENTER and “XXXXXh”
(Hours) is displayed.
4. Tap MODE/ESC to return to the main menu.
23
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
INFORMATION - Time Information - LastRun Password
Display the timer password. (038)
1. Tap MODE/ESC to access main menu, tap UP/DOWN/LEFT/RIGHT until
“Information” is highlighted and tap ENTER.
2. Tap UP/DOWN until “Time Information” is displayed and tap ENTER.
3. Tap UP/DOWN until “LastRun Password” is displayed and tap ENTER.
4. Tap UP/DOWN to select 3-digit password and tap ENTER to confirm selection.
5. Tap MODE/ESC to return to the main menu.
INFORMATION - Time Information - Clear Last Run
Clear the last run time of the fixture, default is OFF.
1. Tap MODE/ESC to access main menu, tap UP/DOWN/LEFT/RIGHT until
“Information” is highlighted and tap ENTER.
2. Tap UP/DOWN until “Time Information” is displayed and tap ENTER.
3. Tap UP/DOWN until “Clear Last Run” is displayed and tap ENTER.
4. Tap UP/DOWN to select desired mode (“ON” or “OFF”) and tap ENTER to
confirm selection. NOTE: A correct password must be entered in the “LastRun
Password” menu in order to clear last run time.
5. Tap MODE/ESC to return to the main menu.
INFORMATION - Temperature Information - Head Temperature
Display the temperature of the fixture, default is Fahrenheit.
1. Tap MODE/ESC to access main menu, tap UP/DOWN/LEFT/RIGHT until
“Information” is highlighted and tap ENTER.
2. Tap UP/DOWN buttons until “Temperature Info” is displayed and tap ENTER.
3. Tap UP/DOWN buttons until “Head Temp” is displayed and tap ENTER.
4. Tap ENTER and “XXX” (degrees) °C/ °F is displayed.
5. Tap MODE/ESC to return to the main menu.
24
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
INFORMATION - Software Version
Display the software version of the fixture.
1. Tap MODE/ESC to access main menu, tap UP/DOWN/LEFT/RIGHT until
“Information” is highlighted and tap ENTER.
2. Tap UP/DOWN until “Software Version” is displayed and tap ENTER.
3. The display will show “VX.X” (software version #)
4. Tap MODE/ESC to return to the main menu.
PERSONALITY - Status Settings - Address Via DMX
Adjust the desired DMX address via an external controller, default is ON.
1. Tap MODE/ESC to access the main menu, tap UP/DOWN/LEFT/RIGHT until
“Personality” is highlighted and tap ENTER.
2. Tap UP/DOWN until “Status Settings” is displayed and tap ENTER.
3. Tap UP/DOWN until “Address Via DMX” is displayed and tap ENTER.
6. Tap UP/DOWN to select desired mode (“ON” or “OFF”) and tap ENTER to
confirm selection.
4. Tap MODE/ESC to return to the main menu.
PERSONALITY - Status Settings - No DMX Status
Fixture runs in Auto Run if no DMX signal is detected. Options include (Hold/Close
Shutter/Music Control/Auto Program), default is Hold.
1. Tap MODE/ESC to access the main menu, tap UP/DOWN/LEFT/RIGHT until
“Personality” is highlighted and tap ENTER.
2. Tap UP/DOWN until “Status Settings” is displayed and tap ENTER.
3. Tap UP/DOWN until “No DMX Status” is displayed and tap ENTER.
4. Tap UP/DOWN to select desired mode (Hold/Close Shutter/Music
Control/Auto Program) and tap ENTER to confirm selection.
5. Tap MODE/ESC to return to the main menu.
25
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
PERSONALITY - Status Settings - Pan Reverse
Reverse the Pan movement, default is OFF.
1. Tap MODE/ESC to access the main menu, tap UP/DOWN/LEFT/RIGHT until
“Personality” is highlighted and tap ENTER.
2. Tap UP/DOWN until “Status Settings” is displayed and tap ENTER.
3. Tap UP/DOWN until “Pan Reverse” is displayed and tap ENTER.
4. Tap UP/DOWN to select desired mode (“ON” or “OFF”) and tap ENTER to
confirm selection.
5. Tap MODE/ESC to return to the main menu.
PERSONALITY - Status Settings - Tilt Reverse
Reverse the Tilt movement, default is OFF.
1. Tap MODE/ESC to access the main menu, tap UP/DOWN/LEFT/RIGHT until
“Personality” is highlighted and tap ENTER.
2. Tap UP/DOWN until “Status Settings” is displayed and tap ENTER.
3. Tap UP/DOWN until “Tilt Reverse” is displayed and tap ENTER.
4. Tap UP/DOWN to select desired mode (“ON” or “OFF”) and tap ENTER to
confirm selection.
5. Tap MODE/ESC to return to the main menu.
PERSONALITY - Status Settings – Pan Degree
Select desired maximum degree of the Pan movement, default is 540°.
1. Tap MODE/ESC to access the main menu, tap UP/DOWN/LEFT/RIGHT until
“Personality” is highlighted and tap ENTER.
2. Tap UP/DOWN until “Status Settings” is displayed and tap ENTER.
3. Tap UP/DOWN until “Pan Degree” is displayed and tap ENTER.
4. Tap UP/DOWN to select desired mode (“Pan 540”, “Pan 540-90offset”, “Pan
630”) and tap ENTER to confirm selection.
5. Tap MODE/ESC to return to the main menu.
26
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
PERSONALITY - Status Settings – Tilt Degree
Select desired maximum degree of the Tilt movement, default is Tilt 270°.
1. Tap MODE/ESC to access the main menu, tap UP/DOWN/LEFT/RIGHT until
“Personality” is highlighted and tap ENTER.
2. Tap UP/DOWN until “Status Settings” is displayed and tap ENTER.
3. Tap UP/DOWN until “Tilt Degree” is displayed and tap ENTER.
4. Tap UP/DOWN to select desired mode (“Tilt 270”, “Tilt 240”) and tap ENTER
to confirm selection.
5. Tap MODE/ESC to return to the main menu.
PERSONALITY - Status Settings - Feedback
Select desired Feedback switch setting of the Pan / Tilt movement, default is ON.
1. Tap MODE/ESC to access the main menu, tap UP/DOWN/LEFT/RIGHT until
“Personality” is highlighted and tap ENTER.
2. Tap UP/DOWN until “Status Settings” is displayed and tap ENTER.
3. Tap UP/DOWN until “Feedback” is displayed and tap ENTER.
4. Tap UP/DOWN to select desired mode (“ON” or “OFF”) and tap ENTER to
confirm selection.
5. Tap MODE/ESC to return to the main menu.
PERSONALITY - Status Settings – Movement Speed
Select desired Movement Speed, default is Speed 1.
1. Tap MODE/ESC to access the main menu, tap UP/DOWN/LEFT/RIGHT until
“Personality” is highlighted and tap ENTER.
2. Tap UP/DOWN until “Status Settings” is displayed and tap ENTER.
3. Tap UP/DOWN until “Movement Speed” is displayed and tap ENTER.
4. Tap UP/DOWN to select desired mode (“Speed 1”, “Speed 2”, “Speed 3”,
“Speed 4”) and tap ENTER to confirm selection.
5. Tap MODE/ESC to return to the main menu.
27
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
PERSONALITY - Status Settings – Mic Sensitivity
Select desired Microphone Sensitivity from 0% to 99%, default is 70%.
1. Tap MODE/ESC to access the main menu, tap UP/DOWN/LEFT/RIGHT until
“Personality” is highlighted and tap ENTER.
2. Tap UP/DOWN until “Status Settings” is displayed and tap ENTER.
3. Tap UP/DOWN until “Mic Sensitivity” is displayed and tap ENTER.
4. Tap UP/DOWN to select desired value (“00%”, to “99%”) and tap ENTER to
confirm selection.
5. Tap MODE/ESC to return to the main menu.
PERSONALITY - Status Settings – Hibernation
Select desired Hibernation time, default is 15m.
1. Tap MODE/ESC to access the main menu, tap UP/DOWN/LEFT/RIGHT until
“Personality” is highlighted and tap ENTER.
2. Tap UP/DOWN until “Status Settings” is displayed and tap ENTER.
3. Tap UP/DOWN until “Hibernation” is displayed and tap ENTER.
4. Tap UP/DOWN to select desired value (“OFF”, “01m” to “99m”) and tap
ENTER to confirm selection.
5. Tap MODE/ESC to return to the main menu.
PERSONALITY - Service Setting - Password
The Password is (050).
1. Tap MODE/ESC to access the main menu, tap UP/DOWN/LEFT/RIGHT until
“Personality” is highlighted and tap ENTER.
2. Tap UP/DOWN until “Service Setting” is displayed and tap ENTER.
3. Tap UP/DOWN until “Password” is displayed and tap ENTER.
4. Tap UP/DOWN to select 3-digit password and tap ENTER to confirm selection.
5. Tap MODE/ESC to return to the main menu.
28
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
PERSONALITY - Service Setting - RDM PID
With this function you can call up various submenus via RDM.
This device is RDM ready. RDM stands for "remote device management" and
makes remote control of devices connected to the DMX-bus. ANSI E1.20-2006 by
ESTA specifies the RDM standard as an extension of the DMX512 protocol.
Manual settings like adjusting the DMX starting address are no longer needed. This
is especially useful when the fixture is installed in a remote area. RDM ready and
conventional DMX devices can be operated in one DMX line. The RDM protocol
sends own packages in the DMX512 data feed and does not influence conventional
devices.
If DMX splitters are used and RDM control is to be used, these splitters must
support RDM. The number and type of RDM parameters depend on the RDM
controller being used.
1. Tap MODE/ESC to access the main menu, tap UP/DOWN/LEFT/RIGHT until
“Personality” is highlighted and tap ENTER.
2. Tap UP/DOWN until “Service Setting” is displayed and tap ENTER.
3. Tap UP/DOWN until “RDM PID” is displayed and tap ENTER.
4. Tap MODE/ESC to return to the main menu.
PERSONALITY – Fans Control
Select desired Fan setting, default is Auto.
1. Tap MODE/ESC to access the main menu, tap UP/DOWN/LEFT/RIGHT until
“Personality” is highlighted and tap ENTER.
2. Tap UP/DOWN until “Fans Control” is displayed and tap ENTER.
3. Tap UP/DOWN to select desired mode (“Auto”, “Low”, “High”) and tap
ENTER to confirm selection.
4. Tap MODE/ESC to return to the main menu.
29
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
PERSONALITY - Display Setting – Shutoff Time
Shut off the Control Panel display after 02 to 60 minutes, default is 05 minutes.
1. Tap MODE/ESC to access the main menu, tap UP/DOWN/LEFT/RIGHT until
“Personality” is highlighted and tap ENTER.
2. Tap UP/DOWN until “Display Setting” is displayed and tap ENTER.
3. Tap UP/DOWN until “Shut off Time” is displayed and tap ENTER.
4. Tap UP/DOWN to select time (02-60) and tap ENTER to confirm selection.
5. Tap MODE/ESC to return to the main menu.
PERSONALITY - Display Setting – Display Reverse
Rotate (Flip) the Control Menu Panel display by 180°, default is OFF.
1. Tap MODE/ESC to access the main menu, tap UP/DOWN/LEFT/RIGHT until
“Personality” is highlighted and tap ENTER.
2. Tap UP/DOWN until “Display Setting” is displayed and tap ENTER.
3. Tap UP/DOWN until “Display Reverse” is displayed and tap ENTER.
4. Tap UP/DOWN to select desired mode (“ON” or “OFF”) and tap ENTER to
confirm selection.
5. Tap MODE/ESC to return to the main menu.
PERSONALITY - Display Setting – Key Lock
Lock the Control Panel buttons automatically after exiting main menu for 15 seconds.
Unlock by keeping the MODE/ESC button pressed for 3 seconds. Default is OFF.
1. Tap MODE/ESC to access the main menu, tap UP/DOWN/LEFT/RIGHT until
“Personality” is highlighted and tap ENTER.
2. Tap UP/DOWN until “Display Setting” is displayed and tap ENTER.
3. Tap UP/DOWN until “Key Lock” is displayed and tap ENTER.
4. Tap UP/DOWN to select desired mode (“ON” or “OFF”) and tap ENTER to
confirm selection.
5. Tap MODE/ESC to return to the main menu.
30
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
PERSONALITY – Display Setting - Disp Flash
Control Panel display will flash if no DMX is signal is detected, default is OFF.
1. Tap MODE/ESC to access the main menu, tap UP/DOWN/LEFT/RIGHT until
“Personality” is highlighted and tap ENTER.
2. Tap UP/DOWN until “Display Setting” is displayed and tap ENTER.
3. Tap UP/DOWN until “Disp Flash” is displayed and tap ENTER.
4. Tap UP/DOWN to select desired mode (“ON” or “OFF”) and tap ENTER to
confirm selection.
5. Tap MODE/ESC to return to the main menu.
PERSONALITY – Temperature C/F
Display the temperature in Celsius or Fahrenheit, default is Fahrenheit.
1. Tap MODE/ESC to access the main menu, tap UP/DOWN/LEFT/RIGHT until
“Personality” is highlighted and tap ENTER.
2. Tap UP/DOWN until “Temperature C/F” is displayed and tap ENTER.
3. Tap UP/DOWN to select desired mode (“Celsius” or “Fahrenheit”) and tap
ENTER to confirm selection.
4. Tap MODE/ESC to return to the main menu.
PERSONALITY – Initial Status
Display the initial effect position for DMX functions.
1. Tap MODE/ESC to access the main menu, tap UP/DOWN/LEFT/RIGHT until
“Personality” is highlighted and tap ENTER.
2. Tap UP/DOWN until “Initial Status” is displayed and tap ENTER.
3. Tap UP/DOWN to select desired function (“Auto Program”, “PAN”, “PAN-Fine”,
“TILT”, “TILT-Fine”, “Move Speed”, “Strobe”, “Dimmer”, “Red(1-4)”,
“Green(1-4)”, “Blue(1-4)”, “White(1-4)”, “Color Macro”, “Color Preset”,
“Color Mode”, “Color Patter”, “Chase Speed”) and tap ENTER to confirm
selection
4. Tap UP to select desired position (“0-255”) and tap ENTER to confirm selection.
5. Tap MODE/ESC to return to the main menu.
31
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
PERSONALITY – Reset Default
Restore factory settings function (ON or OFF), the default is OFF.
1. Tap MODE/ESC to access the main menu, tap UP/DOWN/LEFT/RIGHT until
“Personality” is highlighted and tap ENTER.
2. Tap UP/DOWN until “Reset Default” is displayed and tap ENTER.
3. Tap UP/DOWN to select desired mode (“ON” or “OFF”) and tap ENTER to
confirm selection.
RESET FUNCTION
Reset fixture function (Reset ALL or Reset Pan^Tilt).
1. Tap MODE/ESC to access the main menu, tap UP/DOWN/LEFT/RIGHT until
“Reset Function” is highlighted and tap ENTER.
2. Tap UP/DOWN to select desired mode (Reset ALL or Reset Pan^Tilt) and tap
ENTER to confirm selection.
EFFECT ADJUST – Test Channel
Test each DMX function.
1. Tap MODE/ESC to access the main menu, tap UP/DOWN/LEFT/RIGHT until
“Effect Adjust” is highlighted and tap ENTER.
2. Tap UP/DOWN until “Test Channel” is displayed and tap ENTER.
3. Tap UP/DOWN to select desired function (“Auto Program”, “PAN”, “PAN-Fine”,
“TILT”, “TILT-Fine”, “Move Speed”, “Strobe”, “Dimmer”, “Red(1-4)”,
“Green(1-4)”, “Blue(1-4)”, “White(1-4)”, “Color Macro”, “Color Preset”,
“Color Mode”, “Color Patter”, “Chase Speed”) and tap ENTER to confirm
selection.
4. Tap MODE/ESC to return to the main menu.
32
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
EFFECT ADJUST – Manual Control
Fine adjustment. All effects will be canceled, the shutter opens and the dimmer
intensity will be set to 100 %. With the individual functions, you can focus the light on a
flat surface (wall) and perform the fine lamp adjustment.
1. Tap MODE/ESC to access the main menu, tap UP/DOWN/LEFT/RIGHT until
“Effect Adjust” is highlighted and tap ENTER.
2. Tap UP/DOWN until “Manual Control” is displayed and tap ENTER.
3. Tap UP/DOWN to select desired function (“Auto Program”, “PAN”, “PAN-Fine”,
“TILT”, “TILT-Fine”, “Move Speed”, “Strobe”, “Dimmer”, “Red(1-4)”,
“Green(1-4)”, “Blue(1-4)”, “White(1-4)”, “Color Macro”, “Color Preset”,
“Color Mode”, “Color Patter”, “Chase Speed”) and tap ENTER to confirm
selection.
4. Tap UP to select desired value (“0-255”) and tap ENTER to confirm selection.
5. Tap MODE/ESC to return to the main menu.
EFFECT ADJUST – Calibration
Adjust PAN and TILT to desired positions, password is 050. NOTE: A correct
password must be entered in the “-Password-” menu in order to access PAN and
TILT adjustment menu items.
1. Tap MODE/ESC to access the main menu, tap UP/DOWN/LEFT/RIGHT until
“Effect Adjust” is highlighted and tap ENTER.
2. Tap UP/DOWN until “Calibration” is displayed and tap ENTER.
3. Tap UP/DOWN to select desired function (“PAN” or “TILT”) and tap ENTER to
confirm selection.
4. Tap UP to select desired value (“0-255”) and tap ENTER to confirm selection.
5. Tap MODE/ESC to return to the main menu
33
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
USER MODE SETTING
Select different channels list by different sequence.
For example, after the user enter this manual, if select Auto Program = CH 22, means
in this User’s mode, the “Dimmer” is in Channel 16.
USER MODE SETTING – User Mode
Create user defined channel orders, the default is Stand Mode.
1. Tap MODE/ESC to access the main menu, tap UP/DOWN/LEFT/RIGHT until
“User Mode Set” is highlighted and tap ENTER.
2. Tap UP/DOWN until “User Mode” is displayed and tap ENTER.
3. Tap UP/DOWN to select desired mode (“Stand Mode”, “Basic Mode”, “Extend
Mode”, “User Mode A”, “User Mode B”, “User Mode C”) and tap ENTER to
confirm selection.
4. Tap MODE/ESC to return to the main menu.
USER MODE SETTING – Edit User Mode (A, B, C)
Adjust the rest user defined channel order.
1. Tap MODE/ESC to access the main menu, tap UP/DOWN/LEFT/RIGHT until
“User Mode Set” is highlighted and tap ENTER.
2. Tap UP/DOWN to select desired user (“Edit User Mode A”, “Edit User Mode B”,
“Edit User Mode C”) is displayed and tap ENTER.
3. Tap UP/DOWN to select desired mode (“Max Channel”, “Auto Program”,
“PAN”, “PAN-Fine”, “TILT”, “TILT-Fine”, “Move Speed”, “Strobe”, “Dimmer”,
“Red(1-4)”, “Green(1-4)”, “Blue(1-4)”, “White(1-4)”, “Color Macro”, “Color
Preset”, “Color Mode”, “Color Patter”, “Chase Speed”) and tap ENTER to
confirm selection.
4. Tap UP/DOWN to select desired channel (“None”, “01Ch-17Ch”) and tap ENTER
to confirm selection.
5. Tap MODE/ESC to return to the main menu.
34
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
EDIT PROGRAM – Select Program
Select Auto Programs, default for Auto Pro Part1 is “Program 1”, for Auto Pro Part2
is “Program 2”, and for Auto Pro Part3 is “Program 3”.
1. Tap MODE/ESC to access the main menu, tap UP/DOWN/LEFT/RIGHT until
“Edit Program” is highlighted and tap ENTER.
2. Tap UP/DOWN until “Select Program” is displayed and tap ENTER.
3. Tap UP/DOWN to select desired Auto Program Part (“Auto Pro Part1”, “Auto
Pro Part2”, “Auto Pro Part3”) and tap ENTER to confirm selection.
4. Tap UP/DOWN to select desired Program number (“Program 1” - “Program 10”)
and tap ENTER to confirm selection.
5. Tap MODE/ESC to return to the main menu.
EDIT PROGRAM – Edit Program
Edit the internal programs.
1. Tap MODE/ESC to access the main menu, tap UP/DOWN/LEFT/RIGHT until
“Edit Program” is highlighted and tap ENTER.
2. Tap UP/DOWN until “Edit Program” is displayed and tap ENTER.
3. Tap UP/DOWN to select desired Program number (“Program 1” - “Program 10”)
and tap ENTER to confirm selection.
4. Tap UP/DOWN to select desired test or step (“Pro. Test”, “Step 01” – “Step
64”) and tap ENTER to confirm selection.
5. Tap UP/DOWN to select desired scene (“Sc001” – “Sc250” or “End”) and tap
ENTER to confirm selection.
6. Tap MODE/ESC to return to the main menu.
35
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
EDIT PROGRAM – Edit Scenes
Edit the scenes of the internal programs.
1. Tap MODE/ESC to access the main menu, tap UP/DOWN/LEFT/RIGHT until
“Edit Program” is highlighted and tap ENTER.
2. Tap UP/DOWN until “Edit Scenes” is displayed and tap ENTER.
3. Tap UP/DOWN to select desired Scene number (“Scene 001” - “Scene 250”)
and tap ENTER to confirm selection.
4. Tap UP/DOWN to select desired function (“Auto Program”, “PAN”,
“PAN-Fine”, “TILT”, “TILT-Fine”, “Move Speed”, “Strobe”, “Dimmer”,
“Red(1-4)”, “Green(1-4)”, “Blue(1-4)”, “White(1-4)”, “Color Macro”, “Color
Preset”, “Color Mode”, “Color Patter”, “Chase Speed”, “Fade Time”,
“Secne Time”, “Input By Out”) and tap ENTER to confirm selection.
5. Tap UP/DOWN to select desired position (“0-255”) and tap ENTER to confirm
selection.
6. Tap MODE/ESC to return to the main menu.
EDIT PROGRAM – Record Controller
The fixture features an integrated DMX-recorder by which you can transmit the
programmed scenes from your DMX-controller to the moving head. Adjust the
desired scene numbers via the encoder (from – to). When you call up the scenes at
your controller, they will automatically be transmitted to the moving head.
EDIT PROGRAM – Record Controller – Working With Built In Program
A Master unit can send up to 3 different data groups to the Slave units, i.e. a Master
unit can start 3 different Slave units, which run 3 different programs. The Master unit
sends the 3 program parts in a continuous loop.
The Slave unit receives data from the Master unit according to the group which the
Slave unit was assigned to. If e.g. a Slave unit is set to “Slave 1” in the menu “Set
to Slave”, the Master unit sends “Auto Program Part 1” to the Slave unit.
If set to “Slave 2”, the Slave unit receives “Auto Program Part 2”.
36
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
EDIT PROGRAM – Record Controller – Working With Built-In Program
[continued]
To start an Auto Program proceed as follows:
1. Slave Setting
• Select “Function Mode” by turning on the encoder.
• Press the ENTER button to confirm.
• Select “Set to Slave” by turning the encoder.
• Press the ENTER button to confirm.
• Turn the encoder to select “Slave 1”, “Slave 2” or “Slave 3”.
• Press the ENTER button to confirm.
• Press the MODE/ESC button in order to return to the main menu.
2. Automatic Program Run
• Select “Function Mode” by turning on the encoder.
• Press the ENTER button to confirm.
• Select “Auto Program” by turning on the encoder.
• Press the ENTER button to confirm.
• Turn the encoder to select “Master” or “Alone”. The selection "Alone" means
Stand Alone-mode and "Master" that the device is defined as master.
• Press the ENTER button to confirm.
• Press the MODE/ESC button in order to return to the main menu.
3. Program selection for Auto Pro Part
• Select “Edit Program” by turning the encoder.
• Press the ENTER button to confirm.
• Select “Select Programs” by turning the encoder.
• Press the ENTER button to confirm.
• Turn the encoder to select “Auto Pro Part 1”, “Auto Pro Part 2” or “Auto Pro
Part 3”, and thus select which Slave program is to be sent. Selection “Part 1”
means, that the Slave unit runs the same program as the master units.
• Press the ENTER button to confirm.
• Press the MODE/ESC button in order to return to the main menu.
37
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
EDIT PROGRAM – Record Controller – Working With Built-In Program
[continued]
4. Program Selection for Edit Program
• Select “Edit Program” by turning the encoder.
• Press the ENTER button to confirm.
• Select “Edit Program” by turning the encoder.
• Press the ENTER button to confirm.
• Turn the encoder to select the desired program. With this function you can edit
specific scenes into a specific program.
• Press the ENTER button to confirm.
• Press the MODE/ESC button in order to return to the main menu.
5. Automatic Scene Recording
• Select “Edit Program” by turning the encoder.
• Press the ENTER button to confirm.
• Select “Edit Scenes” by turning the encoder.
• Turn the encoder to select the desired scene numbers. You can program a
maximum number of 250 scenes.
• Press the ENTER button to confirm.
• Press the MODE/ESC button in order to return to the main menu.
Example:
Program 2 includes scenes: 10, 11, 12, & 13
Program 4 includes scenes: 8, 9, & 10
Program 6 includes scenes: 12, 13, 14, & 15
Auto Pro Part 1 is Program 2
Auto Pro Part 2 is Program 3
Auto Pro Part 3 is Program 6
38
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
EDIT PROGRAM – Record Controller – Working With Built-In Program
[continued]
The 3 Slave groups run the Auto Program in certain time segments, as shown in the
following picture:
39
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
41
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
ERROR MESSAGE
When the fixture is powered ON, it goes through a motor reset program first before it is ready.
The display may show “Err channel is XX” if there are problems with one or more channels.
“XX” stands for channel 1, 2, 3, 4, 5, and 6, which has the testing sensor for positioning. For
example, when the display shows “Err channel is Pan movement”, it means there is some
error in channel 1. If there are errors on channel 1, channel 3, channel 6 at the same time,
you may see the error messages, “Err channel is Pan movement”, “Err channel is Tilt
movement”, “Err channel is red led”, flash 2 times, and then the fixture will go through
a second motor reset program. If the error messages remain after performing 2 motor resets,
only the channels that have errors will not work properly, all other channels will work
normally.
Please contact Elation Professional® Customer Support for service.
Service Hours are Monday through Friday 8:00 a.m. to 5:00 p.m. Pacific Standard Time.
Voice: 323-582-3322
Fax: 323-832-9142
PAN - Movement Er (PAN-yoke movement error)
This message will appear after completing the motor reset if the PAN movement is not
located in the default position after the reset. This error can happen if the yoke’s
magnetic-indexing circuit malfunctions (sensor failed or magnet missing) or the
stepper-motor or its driving IC on the main PCB is defective or fails.
TILT- movement Er (TILT-head movement error)
This message will appear after completing the motor reset if the TILT movement is not
located in the default position after the reset. This error can happen if the head’s
magnetic-indexing circuit malfunctions (sensor failed or magnet missing) or the
stepping-motor or its driving IC on the main PCB is defective or fails.
43
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
SNOOT & DIFFUSION FILTER INSTALLATION
SNOOT (SKU# RAY047-SNOOT)
To install place on top of Lens assembly and fix three screws as shown in diagram below.
DIFFUSION FILTER (SKU# RAY047-GFH)
To install place on top of Lens assembly and fix three screws as shown in diagram below.
44
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
CLEANING AND MAINTENANCE
CLEANING
Frequent cleaning is recommended to insure proper function and an extended fixture life.
• Clean each LED lens weekly to avoid weakness of light due to dust accumulation.
• Clean fan weekly to avoid dust accumulation.
• Use a moist, lint-free cloth. Never use alcohol or solvents.
MAINTENANCE
Regular inspections are recommended to insure proper function and an extended life.
There are no user serviceable parts inside this fixture, please refer all other service issues to
an authorized Elation service technician. Should you need any spare parts, please order
genuine parts from your local Elation dealer.
Please refer to the following points during routine inspections:
• A detailed electric check by an approved electrical engineer every three months, to make
sure the circuit contacts are in good condition and prevent overheating.
• Be sure all screws and fasteners are securely tightened at all times. Lose screws may fall
out during normal operation resulting in damage or injury as larger parts could fall.
• Check for any deformations on the housing, color lenses, rigging hardware and rigging
points (ceiling, suspension, trussing). Deformations in the housing could allow for dust to
enter into the fixture. Damaged rigging points or unsecured rigging could cause the
fixture to fall and seriously injure a person(s).
• Electric power supply cables must not show any damage, material fatigue or sediments.
Never remove the ground prong from the power cable.
45
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
TECHNICAL SPECIFICATIONS
ELECTRICAL / THERMAL
Voltage Requirements AC 100 ~240V / 50Hz~60Hz
Fuse Protection
250V / T3.15A
140 Watts
Power Consumption
Ambient Operating
Temperature
14°F to 113°F (-10°C to 45°C)
LIGHT SOURCE
Type
7 x 15W QUAD COLOR RGBW LEDs
100,000 Rated Hours
*May vary depending on several factors including but not limited to: Environmental Conditions,
Power/Voltage, Usage Patterns (On-Off Cycling), Control, and Dimming.
Life Time
PHOTOMETRIC DATA
7˚ Beam ~ 13˚ Field Angles
COLOR MIXING
RGBW Additive Color Mixing, 16.7 Million Color Possibilities
STROBE / DIMMER
Variable Speed Strobe 1 - 18 Flashes Per Second
0-100% Dimmer
DMX CHANNELS
15 (Basic), 17 (Standard), 29 (Extended)
DMX DRIVE
USITT DMX-512, 5-pin XLR; [+] = Pin 3, [-] = Pin 2, [Ground] = Pin 1.
Starting DMX [001].
PAN / TILT
Pan Movement
Tilt Movement
SIZES / WEIGHTS
540° / 630° / 540° - 90° Offset
265°
9.3” (L) x 5.6” (W) x 12.5” (H- Head Vertical)
235 x 141 x 318 mm
Dimensions
12.9” - 326.5mm (H-Head Horizontal with Snoot)
Weight (net)
RATINGS
10.6 lbs / 4.8kgs
IP RATING
IP20
Please Note: Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice.
46
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
PHOTOMETRIC DATA
47
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
DIMENSIONAL DRAWINGS (millimeters)
Please Note: Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice.
48
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . e l a t i o n l i g h t i n g . c o m
CIRCUIT SCHEMATIC
49
RAYZOR Q7™ User Manual 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|