USER’S GUIDE
COLOR MONITOR
Model No : 7d ln
C T L
S/N : 9978628208
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
CONTENTS
Introduction ............................................................................. 1
This manual explains how to correctly install, operate and get the
best performance from your monitor. Please read this user’s
guide carefully before installing your monitor, then keep it near
your monitor for quick reference.
Product Features ................................................................. 2
Setup ......................................................................................... 3
Installing the Tilt/Swivel Stand ......................................... 3
Connecting the Signal Cable and Power Cord..................... 4
Operation & Adjustment ...................................................... 5
Specifications ......................................................................... 10
Factory Preset Timings ......................................................... 10
Troubleshooting ..................................................................... 11
First, please check that the contents of the box corresponds with
the following checklist :
• Color monitor
• Power cord
• Tilt/swivel stand
• User’s Guide
• Warranty Handbook
• Registration Card
If there is any item missing or damaged, please contact your
dealer. Please keep the box and packing materials so that you
may properly store or transport your monitor.
English - 1
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP
PRODUCT FEATURES
• The convenient and user-friendly on-screen display allows for
easy and accurate adjustments of horizontal and vertical
screen size and position, geometry and screen color.
INSTALLING THE TILT/SWIVEL STAND
1. Ensure that the power to the monitor is off.
• The monitor supports a safe working environment in strict
compliance with the MPR II standard for low emissions
(TCO Optional).
2. Set the monitor face down with the underside facing you.
Please be careful so as not to scratch the monitor screen.
• The monitor complies with the VESA Display Data Channel
(DDC) specification for “Plug & Play” compatibility.
Advanced microcircuitry makes set-up and configuration fast
and effortless.
3. Align the four hooks on the stand with the guide holes of
bottom chassis of the monitor.
4. Insert the hooks into the guide holes.
• The monitor features Advanced Color Controls for fine-
tuning to meet your own personal tastes or application
requirements. Use the on-screen controls to adjust the color
temperature, RGB gain value for the best possible screen
color and intensity.
5. Slide the tilt/swivel stand toward the front of the monitor until
the latch locks in position.
6. Turn the monitor and the stand upright.
• Press the menu button and activate the Self-Diagnosis menu
to determine whether your monitor is functioning normally,
not receiving a signal or is receiving a signal that is out of
scanning range.
• Activate the higher refresh rates of the monitor to stabilize the
screen and eliminate the annoying flicker that contributes to
eye-strain and headaches.
Latch
• The “borderless” full-screen display capability works under
all graphic modes and provides a larger viewing area than
conventional monitors, giving you a better picture with more
workspace.
If you want to remove the tilt/swivel stand on the monitor, press
the latch and pull the tilt/swivel stand toward the back of the
monitor. Lift the stand to separate.
English - 2
English - 3
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION & ADJUSTMENT
CONNECTING THE SIGNAL CABLE AND POWER
CORD
Co n t ro l Pa n el
SELECT
ADJUST
MENU
1. Turn off the computer and monitor.
2. Connect the 15 pin D-sub connector to the output port of the
video card in your computer.
3. Tighten the screws of the connector.
MENU
4. Plug the power cord into the AC receptacle located on the back
of the monitor.
• Launch OSD(On-Screen Display) MENU window.
• Select a sub Menu & function.
SELECT
5. Plug the other end of the power cord into the AC outlet.
• Move a sub Menu & function.
• Increase the value of any selected function.
• Adjust the contrast directly when there is no OSD.
• Move a sub Menu & function.
• Decrease the value of any selected function.
• Adjust the brightness directly when there is no
OSD.
Signal Cable
Power Cord
If your power cord is PC-to-Monitor type, plug the other end
of the power cord into the AC receptacle in the computer.
English - 4
English - 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Key Pro cess
OSD Fu n ct io n s
ICON
CONTROL
FUNCTION
MENU
Adjust the position of the display
horizontally (left or right).
H. POSITION
V. POSITION
H.SIZE
Adjust the position of the display
vertically (up or down).
SELECT
MENU
Adjust the display width (horizontal
size).
V.SIZE
Adjust the display height (vertical size).
Adjust the vertical linearity.
MENU
MENU
V. LINEARITY
H. LINEARITY
PINCUSHION
Adjust the horizontal linearity.
O SD O FF
Adjust the left and right margins for
more convex or more concave margins.
Adjust the trapezoid of the screen by
moving the lines inward or outward.
TRAPEZOID
When you choose the icon
exit the OSD screen.
on the OSD window, you can
•
Adjust the side balance when the sides of
the screen are bowed towards left or
right.
PIN BALANCE
Adjust the parallelogram when the
screen is leaning left or right.
PARALLELOGRAM
T. PIN CORNER
B. PIN CORNER
Adjust the pin corner top when the top
sides of the screen are bowed.
Adjust the pin corner bottom when the
bottom sides of the screen are bowed.
English - 6
English - 7
Download from Www.Somanuals.com. All Manuals Search And Download.
ICON
CONTROL
STATUS
FUNCTION
ICON
CONTROL
FUNCTION
Adjust the side pin corner balance top
when the top sides of the screen are
bowed towards left or right.
Display horizontal & vertical frequency
and polarity.
T. PIN BALANCE
Adjust the horizontal picture moire
cancellation.
H. MOIRE
V. MOIRE
RECALL
Adjust the side pin corner balance bottom
when the bottom sides of the screen are
bowed towards left or right.
B. PIN BALANCE
COLOR TEMP
Adjust the vertical picture moire
cancellation.
Choose different preset color temperatures
or set your own customized color
parameters.
Reset the screen to the Factory Preset
Display Settings.
RED GAIN
Adjust the red gain.
Adjust the green gain.
Adjust the blue gain.
Adjust the red bias.
Adjust the green bias.
Adjust the rotation when the screen is
tilted left or right.
ROTATION
GREEN GAIN
Self Dia g n o sis
BLUE GAIN
RED BIAS
When the monitor doesn’t display, if you press any control key,
Self Diagnosis screen is displayed. Self Diagnosis function
checks if the status of the monitor is No Signal or Out of range.
No Signal screen is displayed when the D-
Sub signal connector is not connected or
the status of the monitor is on DPMS
mode.
GREEN BIAS
BLUE BIAS
LANGUAGE
Adjust the blue bias.
Out of Range screen is displayed when
the applied frequency is under or over
normal range.
Select language for OSD (5 languages).
Normal range
H : 30 - 70 KHz
V : 50 - 160 Hz
Degaussing keeps the monitor free from
unwanted magnetism that can result in
color impurity.
DEGAUSS
English - 8
English - 9
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
TROUBLESHOOTING
CDT Size
17-inch
Symptom
Check
Diagonal visible image area
Dot Pitch
16.2-inch
0.27 mm
No picture.
Check if POWER SWITCH and COMPUTER
POWER SWITCH are in the on position.
Synchronization
Horizontal 30 - 70 KHz
Vertical
50 - 160 Hz
Check if the signal cable is correctly connected to
the video card.
Plug and Play
DDC1/2B/CI
Power Saving
Power Source
EPA, VESA DPMS, Nutek Compliant
100-240 Vac, 50/60Hz (Free Voltage)
95W
Check if the pins of D-sub connector are not bent.
Check if the computer is in the power saving mode.
Power Consumption
Dimension-W x H x D
(set with stand)
420 x 453 x 429mm
POWER LED is not Check if POWER SWITCH is in the on position.
Weight-unpacked (lbs/Kg)
Operating Temperature
33.9/15.4
lit.
10 ~ 40°C /50 ~ 104°F
Check if the power cord is correctly connected.
Image is unstable.
Check if the signal cable is suitable to the video card.
Image is not
centered, too small
or too large.
Adjust H & V Size or H & V Position to get the
proper image.
FACTORY PRESET TIMINGS
Resolution
Mode
H.Freq (KHz) V.Freq(Hz)
Remark
(dots
X
lines)
Picture bounces or a Keep the devices that may cause electrical
VGA 480
640
640
X
480
31.5
37.5
31.5
46.9
53.7
60.0
68.7
64.0
60
75
70
75
85
75
85
60
Non-interlaced
Non-interlaced
Non-interlaced
Non-interlaced
Non-interlaced
Non-interlaced
Non-interlaced
Non-interlaced
wave pattern is
present in the
picture.
interference away from the monitor.
VESA VGA 75
VGA 400
X
480
720
X
X
X
X
X
X
400
See the FCC information at the front cover of the
manual.
VESA 46K
800
600
VESA SVGA 85
VESA 60K
800
600
Color looks blotchy. Operate Degauss once.
1024
1024
1280
768
VESA 1024/85
VESA 1280/60
768
Picture is blurred.
Adjust Contrast and Brightness.
1024
Operate Degauss once.
The above timings are adjusted on the best display image condition.
Edges of available
area on the screen
are not straight.
Adjust Geometry Control (Pincushion, Trapezoid..).
English - 10
English - 11
Download from Www.Somanuals.com. All Manuals Search And Download.
|