9.6V CORDLESS
ROTARY TOOL KIT
Model 92880
SET up AnD OpERATIng InSTRuCTIOnS
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE ThIS MAnuAL.
©
®
Copyright 2005 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of Harbor
FreightTools. Diagramswithinthismanualmaynotbedrawnproportionally. Duetocontinuingimprovements,
actual product may differ slightly from the product described herein.
For technical questions or replacement parts, please call 1-800-444-3353.
Manual Revised 10e
Download from Www.Somanuals.com. All Manuals Search And Download.
3. personal safety
must be NIOSH-approved for the specific
hazards in the work area.
a.Stay alert, watch what you are
doing and use common sense when
operating a power tool. Do not use
a power tool while you are tired or
under the influence of drugs, alcohol
or medication. A moment of inattention
while operating power tools may result in
serious personal injury.
4. power tool use and care
a.Do not force the power tool. use
the correct power tool for your
application. The correct power tool will
do the job better and safer at the rate for
which it was designed.
b.Do not use the power tool if the
switch does not turn it on and off.
Any power tool that cannot be controlled
with the switch is dangerous and must
be repaired.
b.use safety equipment. Always wear
eye protection. Safety equipment such
as a dust mask, non-skid safety shoes,
a hard hat, or hearing protection used
for appropriate conditions will reduce
personal injuries.
c.Disconnect the plug from the power
source and/or the battery pack from
the power tool before making any
adjustments, changing accessories,
or storing power tools. Such
preventive safety measures reduce
the risk of starting the power tool
accidentally.
c.prevent unintentional starting. Ensure
the switch is in the off-position before
connecting to power source and/or
battery pack, picking up or carrying
the tool. Carrying power tools with your
finger on the switch or energizing power
tools that have the switch on invites
accidents.
d.Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or
these instructions to operate the
power tool. Power tools are dangerous
in the hands of untrained users.
d.Remove any adjusting key or wrench
before turning the power tool on.
A wrench or a key left attached to a
rotating part of the power tool may result
in personal injury.
e.Maintain power tools. Check for
misalignment or binding of moving
parts, breakage of parts and any other
condition that may affect the power
tool’s operation. If damaged, have
the power tool repaired before use.
Many accidents are caused by poorly
maintained power tools.
e.Do not overreach. Keep proper
footing and balance at all times. This
enables better control of the power tool
in unexpected situations.
f. Dress properly. Do not wear loose
clothing or jewelry. Keep your hair,
clothing and gloves away from
moving parts. Loose clothes, jewelry or
long hair can be caught in moving parts.
f. Keep cutting tools sharp and clean.
Properly maintained cutting tools with
sharp cutting edges are less likely to
bind and are easier to control.
g.Only use safety equipment that has
been approved by an appropriate
standards agency. Unapproved safety
equipment may not provide adequate
protection. Eye protection must be
ANSI-approved and breathing protection
g.use the power tool, accessories and
tool bits etc. in accordance with these
instructions, taking into account the
working conditions and the work to
REV 10e
SKU 92880
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
be performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
and specifications provided with
this power tool. Failure to follow all
instructions listed below may result in
electric shock, fire and/or serious injury.
5. Battery tool use and care
2. Do not use accessories which
are not specifically designed
a.Recharge only with the charger
specified by the manufacturer. A
charger that is suitable for one type of
battery pack may create a risk of fire
when used with another battery pack.
and recommended by the tool
manufacturer. Just because the
accessory can be attached to your power
tool, it does not assure safe operation.
b.Use power tools only with specifically
designated battery packs. Use of any
other battery packs may create a risk of
injury and fire.
3. The rated speed of the accessory
must be at least equal to the
maximum speed marked on the power
tool. Accessories running faster than
their RATED SPEED can break and fly
apart.
c.When battery pack is not in use, keep
it away from other metal objects, like
paper clips, coins, keys, nails, screws
or other small metal objects, that can
make a connection from one terminal
to another. Shorting the battery
terminals together may cause burns or a
fire.
4. The outside diameter and the
thickness of your accessory must
be within the capacity rating of
your power tool. Incorrectly sized
accessories cannot be adequately
guarded or controlled.
d.under abusive conditions, liquid
may be ejected from the battery;
avoid contact. If contact accidentally
occurs, flush with water. If liquid
contacts eyes, additionally seek
medical help. Liquid ejected from the
battery may cause irritation or burns.
5. The shank of the accessories must
properly fit the Collet of the power
tool. Accessories with arbor holes that
do not match the mounting hardware of
the power tool will run out of balance,
vibrate excessively and may cause loss
of control.
6. Service
a.have your power tool serviced by a
qualified repair person using only
identical replacement parts. This will
ensure that the safety of the power tool
is maintained.
6. Do not use a damaged accessory.
Before each use inspect the
accessory such as abrasive wheels
for chips and cracks, backing pad for
cracks, tear or excess wear. If power
tool or accessory is dropped, inspect
for damage or install an undamaged
accessory. After inspecting and
installing an accessory, position
yourself and bystanders away from
the plane of the rotating accessory
and run the power tool at maximum
no-load speed for one minute.
Safety Warnings grinding, Sanding,
polishing, or Abrasive Cutting
Operations
1. This power tool is intended to
function as a grinder, sander,
polisher or cut-off tool. Read all safety
warnings, instructions, illustrations
REV 10e
Page 4
For technical questions, please call 1-800-444-3353.
SKU 92880
Download from Www.Somanuals.com. All Manuals Search And Download.
Damaged accessories will normally
break apart during this test time.
12. Do not operate the power tool near
flammable materials. Sparks could
ignite these materials.
7. Wear personal protective equipment.
Depending on application, use face
shield, safety goggles or safety
13. Do not use accessories that require
liquid coolants. Using water or other
liquid coolants may result in electrocution
or shock.
glasses. As appropriate, wear dust
mask, hearing protectors, gloves
and workshop apron capable of
stopping small abrasive or work piece
fragments. The eye protection must
be capable of stopping flying debris
generated by various operations.
The eye protection must be capable
of stopping flying debris generated by
various operations. The dust mask or
respirator must be capable of filtering out
particles generated by your operation.
Prolonged exposure to high intensity
noise may cause hearing loss.
14. Maintain labels and nameplates on
the tool. These carry important safety
information. If unreadable or missing,
contact Harbor Freight Tools for a
replacement.
15. Avoid unintentional starting. Prepare
to begin work before turning on the tool.
16. Do not depress the spindle lock when
starting or during operation.
17. use clamps (not included) or other
practical ways to secure and support
the workpiece to a stable platform.
Holding the work by hand or against your
body is unstable and may lead to loss of
control and personal injury.
8. Keep bystanders a safe distance away
from work area. Anyone entering
the work area must wear personal
protective equipment. Fragments of
work piece or of a broken accessory
may fly away and cause injury beyond
immediate area of operation.
18.
The battery charger gets
hot during use. The
charger’s heat can build up to
unsafe levels and create a fire
9. never lay the power tool down until
the accessory has come to a complete
stop. The spinning accessory may grab
the surface and pull the power tool out of
your control.
hazard if it does not receive adequate
ventilation, due to an electrical fault, or if
it is used in a hot environment. Do not
place the charger on a flammable
surface. Do not obstruct any vents on
the charger. Especially avoid placing
the charger on carpets and rugs; they
are not only flammable, but they also
obstruct vents under the charger.
10. Do not run the power tool while
carrying it at your side. Accidental
contact with the spinning accessory
could snag your clothing, pulling the
accessory into your body.
11. Regularly clean the power tool’s air
vents. The motor’s fan will draw the
dust inside the housing and excessive
accumulation of powdered metal may
cause electrical hazards.
19. This product is not a toy. Keep it out
of reach of children.
20. people with pacemakers should
consult their physician(s) before
use. Electromagnetic fields in close
proximity to heart pacemaker could
REV 10e
SKU 92880
For technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
cause pacemaker interference or
pacemaker failure. In addition, people
with pacemakers should:
• Avoid operating alone.
• Do not use with power switch locked
on.
possible conditions and situations
that may occur. It must be understood
by the operator that common sense and
caution are factors which cannot be built
into this product, but must be supplied by
the operator.
• Properly maintain and inspect to avoid
electrical shock.
Vibration Safety
• Any power cord must be properly
grounded. Ground Fault Circuit
Interrupter (GFCI) should also be
implemented – it prevents sustained
electrical shock.
This tool vibrates during use. Repeated
or long-term exposure to vibration may cause
temporary or permanent physical injury,
particularly to the hands, arms and shoulders.
To reduce the risk of vibration-related injury:
21. WARnIng: Some dust created by power
sanding, sawing, grinding, drilling, and
other construction activities, contains
chemicals known [to the State of
1. Anyone using vibrating tools regularly
or for an extended period should first
be examined by a doctor and then have
regular medical check-ups to ensure
medical problems are not being caused
or worsened from use. Pregnant
California] to cause cancer, birth defects
or other reproductive harm. Some
examples of these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and
cement or other masonry products
• Arsenic and chromium from chemically
treated lumber
Your risk from these exposures varies,
depending on how often you do this type
of work. To reduce your exposure to
these chemicals: work in a well ventilated
area, and work with approved safety
equipment, such as those dust masks
that are specially designed to filter out
microscopic particles. (California Health
& Safety Code § 25249.5, et seq.)
women or people who have impaired
blood circulation to the hand, past hand
injuries, nervous system disorders,
diabetes, or Raynaud’s Disease should
not use this tool. If you feel any medical
or physical symptoms related to vibration
(such as tingling, numbness, and white
or blue fingers), seek medical advice as
soon as possible.
2. Do not smoke during use. Nicotine
reduces the blood supply to the hands
and fingers, increasing the risk of
vibration-related injury.
3. Wear suitable gloves to reduce the
vibration effects on the user.
22. WARnIng: Handling the cord on this
product will expose you to lead, a
4. Use tools with the lowest vibration when
there is a choice between different
processes.
chemical known to the State of California
to cause cancer, and birth defects or
other reproductive harm. Wash hands
after handling. (California Health &
Safety Code § 25249.5, et seq.)
5. Include vibration-free periods each day
of work.
23. The warnings, precautions, and
instructions discussed in this
6. Grip tool as lightly as possible (while still
keeping safe control of it). Let the tool
instruction manual cannot cover all
do the work.
REV 10e
Page 6
For technical questions, please call 1-800-444-3353.
SKU 92880
Download from Www.Somanuals.com. All Manuals Search And Download.
7. To reduce vibration, maintain the tool
as explained in this manual. If any
abnormal vibration occurs, stop use
immediately.
Laboratories, Inc., the Canadian
Standard Association, and the National
Electrical Code.
2. Double insulated tools may be used in
either of the 120 volt outlets shown in the
preceding illustration. (See Outlets for
2-prong plug.)
SAVE ThESE InSTRuCTIOnS.
grounding
Extension Cords
TO pREVEnT
note: Extension cords must not be used
ELECTRIC ShOCK
with this item’s charger.
AnD DEATh FROM
InCORRECT gROunDIng WIRE
COnnECTIOn:
Symbology
Check with a qualified electrician
if you are in doubt as to whether
the outlet is properly grounded.
Do not modify the power cord
plug provided with the tool.
never remove the grounding
prong from the plug. Do not use
the tool if the power cord or plug
is damaged. If damaged, have it
repaired by a service facility
before use. If the plug will not fit
the outlet, have a proper outlet
installed by a qualified
Double Insulated
Canadian Standards Association
Underwriters Laboratories, Inc.
Volts Alternating Current
V~
A
Amperes
No Load Revolutions per Minute
(RPM)
n xxxx/min.
0
electrician.
Double Insulated Tools: Tools with Two
prong plugs
Outlets for 2-prong plug
1. Tools marked “Double Insulated” do not
require grounding. They have a special
double insulation system which satisfies
OSHA requirements and complies with
the applicable standards of Underwriters
REV 10e
SKU 92880
For technical questions, please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Charging the Battery pack
SpECIFICATIOnS
High-Impact Plastic
Battery packs are normally shipped with
low or no charge to prevent potential
problems during shipment. Before use,
you must charge your new battery pack.
Housing, Brass Spindle &
Collets, Stainless Chuck
Body
Construction
9.6 VDC / NiCd Battery
Power Required
Battery Recharge
Pack
120 VAC to 12 VDC
Transformer
Variable:
5,000 - 25,000 RPM
Tool Speed
LED Source
Features
(2) CR-927 3 VDC batteries
Variable Speed,
LED Light Attachment
unpacking
When unpacking, make sure that the item is
intact and undamaged. If any parts are missing or
broken, please call Harbor Freight Tools at 1-800-
444-3353 as soon as possible.
Figure 2
note: Batteries will not reach full charge the
first time they are charged. Allow several
cycles (operation followed by recharging)
before the battery will become fully charged.
When unpacking, check to make sure the
following parts are included:
9.6V Rotary Tool w/Battery
Shaft Mounted LED Light Attachment
AC/DC Transformer
9.6V Battery Charger Base
3-piece Cutoff Wheel Set
4-Piece Sanding Drum Set
36-Piece Sanding Disc Set
2-Piece Buffing Wheel Set
2-Piece Brass Collet Set
2-Piece Drill Bit Set
10-Piece Mounted Stone Set
2-Piece Diamond Burr Set
Flat Wrench
Square Stone Dresser
Plastic Carrying Case
WARnIng: Battery explosion may cause
serious personal or property injury including
death. Charge the battery only within a 50° to
100° temperature range. Lower temperatures
may inhibit charging. Higher temperatures
increase chance of battery failure, including
explosion.
1. Charge the battery pack only with the
included Charger Base (25). Use of
other chargers may cause battery failure
including explosion.
2. Ensure that the Charger Base (25) is
connected to a circuit breaker protected
120 VAC, 60 Hz power supply only.
3. Connect the Charger Base to the
Transformer (24), by plugging it in as
shown in Figure 2. Plug the Transformer
(24) into a 120 VAC wall outlet.
Figure 1
REV 10e
Page 8
For technical questions, please call 1-800-444-3353.
SKU 92880
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Insert the battery pack into the Charger
Base (25) by aligning the ribs on the
Charger Base with the grooves in the
battery pack. Press the battery pack into
place.
InSTRuCTIOnS FOR puTTIng
InTO uSE
Read the EnTIRE IMpORTAnT
SAFETY InFORMATIOn
section at the beginning of this
manual including all text under
subheadings therein before set up
or use of this product.
6. Press down on the battery pack to make
sure that the contacts on the battery pack
are fully engaged with the contacts in the
charger unit.
TO pREVEnT
SERIOuS InjuRY
FROM ACCIDEnTAL
7. While being charged, the green LED will
be lit, indicating that the charger is in
operation. During recharging, the battery
pack will become slightly warm to the
touch. This is normal and not a cause for
concern.
OpERATIOn:
Turn the power Switch of the tool
off and remove the Battery pack
before assembling or making any
adjustments to the tool.
8. Do not place the battery and charger in
an environment of extreme heat or cold.
They will work best at room temperature.
note: For additional information regarding the
parts listed in the following pages, refer
to the Assembly Diagram near the end of
this manual.
9. note: The Charger Base (25) will
not shut off automatically. When the
battery is fully charged (after 3 to 3-1/2
hours), unplug the battery charger and
remove the battery pack. Do not leave
the battery in the Charger Base (25)
indefinitely.
Work piece and Work Area Set up
1. Designate a work area that is clean and
well-lit. The work area must not allow
access by children or pets to prevent
distraction and injury.
Installing the Battery pack
1. Place the battery pack in the tool, aligning
the arrows on the battery pack with the
arrows on the tool.
2. Route the power cord along a safe
route to reach the work area without
creating a tripping hazard or exposing
the power cord to possible damage. The
power cord must reach the work area
with enough extra length to allow free
movement while working.
2. Press the battery pack into the tool. Make
sure that the battery pack snaps into
place, and that the battery pack is secure
in the tool before beginning use.
3. Secure loose work pieces using a vise
or clamps (not included) to prevent
movement while working.
Removing the Battery pack
1. Press the Release Tabs (19) on both
sides of the battery pack to release the
battery from the tool.
4. There must not be hazardous objects,
such as utility lines or foreign objects,
nearby that will present a hazard while
working.
2. Remove the battery pack from the tool by
pulling straight out.
REV 10e
SKU 92880
For technical questions, please call 1-800-444-3353.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
5. You must use personal safety equipment
including, but not limited to, ANSI-
approved eye and hearing protection, as
well as heavy work gloves.
use, possibly causing injury. Allow the bit
time to cool before handling it.
3. To remove a bit: Pull the bit straight out
of the Collet once the Collet Nut is loose.
To insert a bit: Insert the shank end if the
bit into the Collet once the Collet Nut is
loose.
6. Before beginning work, provide for
sparks and debris that will fly off the
work surface. CAuTIOn: Always have
access to a type AAA fire extinguisher.
Collet Nut
Collets
SET-up
Figure 10
Inserting a Bit in the Tool
nOTE: Your tool is provided with two collets,
1/8” and 3/32” diameter. These are
precision manufactured to fit comparably
sized bits. Do not force a bit into the
wrong sized collet, and do not modify a
mismatched collet or bit.
note: Only use accessories that are rated at
or above the RPM rating of the Cordless
Rotary Tool.
WARnIng: Always allow the motor to come
to a complete stop before engaging the
spindle lock.
Severe personal or property damage
may result from using mismatched
collets or bits.
WARnIng: Always remove the battery
pack before making any adjustments
or changing bits, to prevent accidental
starting of the tool. Accidental starting of
the tool may result in serious personal or
property injury.
4. Tighten Collet Nut securely using the
provided wrench. Ensure that the spindle
lock is released before turning on the tool.
WARnIng: Be sure the Collet Nut is tight
before turning on the tool. Bits may be
ejected from a tool if the Collet Nut is loose,
potentially causing severe personal or
property damage.
Installing the Flexible Shaft
2. Be sure that the Rotary Tool is turned
OFF (the “O” position), and that the
Battery is removed from the Handle
before attaching the Flexible Shaft
Attachment (26).
Figure 10
1. Depress the Spindle Lock (10). Rotate
collet until shaft is engaged by the lock.
2. Loosen the Collet Nut (1) by turning it
counterclockwise, using the Wrench
provided.
3. Remove any bits that might be installed.
Remove the Collet Lock Nut and the
Collet.
WARnIng: If you are changing a bit
immediately after use, be careful not to
touch the bit. It may be very hot from
4. Remove the Collar or LED Collar from the
tool Body by turning it counterclockwise.
REV 10e
Page 10
For technical questions, please call 1-800-444-3353.
SKU 92880
Download from Www.Somanuals.com. All Manuals Search And Download.
turning clockwise. Tighten in place using
the Wrench, and the Round “L” Tool as a
hold back.
Installing or Removing Collars
The Front Collar (3) is interchangeable
with the LED Lighted Attachment (23).
Figure 10
5. Pass the end of the Flexible Shaft Core
through the Collet Nut, and into the 1/8”
Collet. Depress the Spindle Lock (10),
and hold it down while tightening the
Collet Nut with the Wrench.
Figure 10
6. When the Collet Nut is tight, release the
Spindle Lock (10) and turn the Flexible
Shaft Attaching Nut clockwise onto the
tool body until hand tight.
1. To install the LED Lighted Attachment,
remove the standard collar by turning
counterclockwise, and install the LED
Lighted Attachment by turning clockwise.
Installing a Bit in the Flexible Shaft
note: When installing or removing, use only
hand pressure and tighten firmly by
hand. Do not overtighten, as this may
damage the part.
Wrench
2. To change the batteries in the LED
Lighted Attachment, first remove it from
the Rotary Tool.
Loosen
Tighten
“L” Tool
Figure 10
Figure 10
3. Using a phillips screw driver, open the
battery compartment.
1. Use the Round “L” Tool to prevent the
Flexible Shaft Core from turning by
inserting it into the hole in the side of the
Flexible Shaft Handle.
2. Once “L” tool is in place, remove
the Collet locking nut by turning it
counterclockwise with the Wrench.
Figure 10
4. Replace the batteries with the same type
as originally installed (Two CR-927 3
VDC batteries). Be sure to match the
polarity marking in the battery
compartment.
3. Place the bit into the appropriate sized
collet. Place the collet into the end of the
Flexible Shaft Handle. Place the Collet
Locking Nut over the bit, and tighten it by
REV 10e
SKU 92880
For technical questions, please call 1-800-444-3353.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Store the tool, its battery, and its bits and
attachments in their case in a safe location.
OpERATIng InSTRuCTIOnS
Read the EnTIRE IMpORTAnT
SAFETY InFORMATIOn
section at the beginning of this
manual including all text under
subheadings therein before set up
or use of this product.
8. Dispose of used batteries properly.
Consult your local hazardous waste
authority for disposal guidelines.
1. Charge the Battery Pack (18) and insert
it in the tool, as described in the previous
section.
2. Select an appropriate bit or attachment
for the job. Insert the bit or attachment as
described in the previous section.
3. The LED Lighted Collar light may be
turned on by moving the switch on the
collar.
Figure 10
4. Rotate the Switch (8) to the ON position.
nOTE: This is a variable speed switch.
The tool bit speed is dependent on the
position of the Switch. Use a speed
appropriate to the bit and the material
being worked on. In general, harder
materials require faster speeds and softer
materials require slower speeds. Relative
speeds are indicated by the numbers on
the Switch.
5. Apply the tool bit to the work material as
needed.
6. When the task has been completed, stop
the tool by rotating the Switch (8) to the
OFF (“O”) position. If the LED Collar
light is ON, switch it OFF. Unplug the
rechargeable battery. Remove the bit or
attachment as discussed in the previous
section.
Page 12
For technical questions, please call 1-800-444-3353.
SKU 92880
Download from Www.Somanuals.com. All Manuals Search And Download.
store your tool and its accessories in the
case provided.
MAInTEnAnCE AnD
SERVICIng
5. Protect the tool and its parts and
accessories from moisture and damp or
corrosive atmospheres.
Procedures not specifically
explained in this manual must
be performed only by a qualified
technician.
6. Protect this tool from damage. Do
not leave it in a place where it can be
banged around, such as a truck bed or
vehicle trunk.
TO pREVEnT
SERIOuS InjuRY
FROM ACCIDEnTAL
OpERATIOn:
7. Some of the bits provided are “grinding
bits” using stone abrasives. During use,
these may clog up with removed material
or lose their shape. To clean and
Turn the power Switch of the tool
off and remove the Battery pack
before performing any
inspection, maintenance, or
cleaning procedures.
reshape these bits, run them against the
provided Dressing Stone. The Dressing
Stone will abrade away the clogging
materials and will reshape the Grinding
Bits as appropriate.
TO pREVEnT SERIOuS InjuRY
FROM TOOL FAILuRE:
Do not use damaged equipment.
If abnormal noise or vibration
occurs, have the problem
8. NiCd BATTERy MUST BE RECyCLED
OR DISPOSED OF PROPERLy. Do not
short, incinerate or open battery.
corrected before further use.
Cleaning, Maintenance, and Lubrication
9.
WARnIng! If the supply cord of the
Transformer is damaged, it must be
replaced only by a qualified service
technician.
1. BEFORE EACh uSE, inspect the
general condition of the tool. Check for
loose screws, misalignment or binding of
moving parts, cracked or broken parts,
damaged electrical wiring, and any
other condition that may affect its safe
operation.
Accessory Storage and handling
1. Handle accessories carefully to prevent
dropping or bumping. Do not use wheels
that have been dropped or bumped.
2. AFTER uSE, wipe external surfaces of
the tool with clean cloth.
2. Store accessories in carrying case.
Store in a dry area above freezing
3. Periodically blow dust and grit out of the
motor vents using dry compressed air.
Wear ANSI-approved safety goggles and
NIOSH-approved breathing protection
while doing this.
temperatures. Any grinding or cut-off
wheels exposed to humidity or freezing
temperatures must not be used. Keep
all accessories out of reach of children.
4. A plastic storage case has been provided
for safe storage of your Rotary Tool and
its bits, parts and accessories. Always
SKU 92880
For technical questions, please call 1-800-444-3353.
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
pARTS LIST - ACCESSORIES
part
Description
A
B
C
D
E
F
G
H
I
10-Piece Mounted Stone Set
2-Piece Buffing Wheel Set
4-Piece Sanding Drum Set
36-Piece Sanding Disc Set & 3-Piece Cutoff Wheel Set
2-Piece Drill Bit Set
Flat Wrench
2-Piece Diamond Burr Set
Square Stone Dresser
2-Piece Brass Collet Set
“L” tool not shown
DIAgRAM - ACCESSORIES
D
E
C
B
F
G
A
H
I
pLEASE READ ThE FOLLOWIng CAREFuLLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLy DIAgRAM
IN THIS MANUALASAREFERENCE TOOL ONLy. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAkES
ANy REPRESENTATION OR WARRANTy OF ANy kIND TO THE BUyER THAT HE OR SHE IS qUALIFIED TO
MAkE ANy REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS qUALIFIED TO REPLACE ANy PARTS
OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR ExPRESSLy STATES THAT
ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAkEN By CERTIFIED AND LICENSED
TECHNICIANS, AND NOT By THE BUyER. THE BUyER ASSUMES ALL RISk AND LIABILITy ARISINg OUT
OF HIS OR HER REPAIRS TO THE ORIgINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISINg
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
REV 10e
Page 14
For technical questions, please call 1-800-444-3353.
SKU 92880
Download from Www.Somanuals.com. All Manuals Search And Download.
pARTS LIST
part
1
Description
Collet Nut
Qty.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
1
2
2
1
1
1
1
1
1
2
Collet
(18)
(24)
(25)
3
Front Collar
Driver Shaft
Bearing #696
Sleeve
4
5
6
7
Motor
8
Switch
9
Spindle Lock Spring
Spindle Lock
Left Cover
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
Left Cover Label
Rubber Buffer
Right Cover
Screw
Right Cover Label
Battery Cover
Battery
26
23
Release Tab
Back - Moving Spring
End Cover
Hanger
LED Light Attachment
Transformer
Charger Base
Flexible Shaft Attachment
ASSEMBLY DIAgRAM
REV 10e
SKU 92880
For technical questions, please call 1-800-444-3353.
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED 90 DAY WARRAnTY
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and
durability standards, and warrants to the original purchaser that this product is free from defects
in materials and workmanship for the period of 90 days from the date of purchase. This warranty
does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents,
repairs or alterations outside our facilities, criminal activity, improper installation, normal wear
and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons
or property, or for incidental, contingent, special or consequential damages arising from the use
of our product. Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS
ExPRESSLy IN LIEU OF ALL OTHER WARRANTIES, ExPRESS OR IMPLIED, INCLUDINg
THE WARRANTIES OF MERCHANTABILITy AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the complaint must
accompany the merchandise. If our inspection verifies the defect, we will either repair or replace
the product at our election or we may elect to refund the purchase price if we cannot readily and
quickly provide you with a replacement. We will return repaired products at our expense, but if
we determine there is no defect, or that the defect resulted from causes not within the scope of
our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary
from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
Record product’s Serial number here:
note: If product has no serial number, record month and year of purchase instead.
note: Some parts are listed and shown for illustration purposes only, and are not available
individually as replacement parts.
REV 10e
Page 16
For technical questions, please call 1-800-444-3353.
SKU 92880
Download from Www.Somanuals.com. All Manuals Search And Download.
|