MA0405-EA
Operation Guide ID-25B
ILLUSTRATION
SET
RESET
WAVE
SET
RESET
WAVE
• A sticker is affixed to the glass of this clock when you purchase it. Be sure to remove the sticker before using the
clock.
°C
°F
MSF DCF
• Depending on the clock model, the configuration of your clock may differ somewhat from that shown in the
illustration.
°C °F
MSF DCF
Normal Display
DATE (month – date)
Day of the week
Antenna Icon
Wave OK indicator
Receive indicator
Transmitter Indicator
(DCF or MSF)
PM indicator
Current time
(Hour, minutes, seconds)
DST indicator
1cm
Current Temperature
Current Humidity
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Guide ID-25B
Setting the Time and Date Manually
THERMOMETER FUNCTIONS
• When using the clock in an area that is outside of the range of the transmitter or in an area where signal
reception is impossible for some reason, you need to manually adjust the time setting as required.
1. Press the SET button (2) to cycle through the setting screens as shown below.
• A built-in sensor measures temperature and shows the measured value on the display. The readout from the
temperature sensor can also be switched between Celsius (°C) and Fahrenheit (°F).
• The temperature display shows “LO” for temperatures below –50°C (–58°F) and “HI” for temperatures above
70°C (158°F).
• Though temperature readings are displayed up to 0°C (32°F) and greater than 40.1°C (104°F), note that such
readings are actually outside the guaranteed temperature range of this clock.
Normal Timekeeping Screen
Switching between Celsius and Fahrenheit
• Slide the °C / °F switch (6) to specify Celsius (°C) or Fahrenheit (°F) as the temperature unit.
HYGROMETER FUNCTION
• A built-in sensor measures humidity and shows the measured value on the display.
• The humidity display shows “LO” for humidity below 10% and “HI” for humidity above 95%.
Year Setting Screen
12-hour/24-hour Timekeeping Screen
BATTERY REPLACEMENT
Replace batteries whenever the display of the clock becomes dim and difficult to read.
1. Pressing down lightly on the battery compartment cover, slide it downwards and remove it.
2. Remove all of the old batteries.
3. Load a full set of new batteries. Make sure that their positive (+) and negative (–) ends face in the correct
directions. If you load batteries incorrectly, they can burst and damage the clock.
4. Replace the battery compartment cover.
5. Press the RESET button (3). Be sure to press the RESET button (3) after replacing batteries.
Battery precautions
• Keep batteries out of the reach of small children. If a battery is accidentally swallowed, contact your physician
immediately.
Month and Day Setting Screen
Time Setting Screen
• Be sure to load the batteries with their positive (+) and negative (–) ends facing correctly.
• Never mix old and new batteries, or batteries of different brands.
• Never charge the batteries that come with the clock.
• Should batteries ever leak while in the clock, wipe out the fluid with a cloth, taking care not to let any get onto
your skin.
• Replace the batteries at least once a year, even if the current batteries are working properly.
• The batteries that come with the clock lose some of their power during transport and storage.
2. While the screen you want is on the display, use the Time Set buttons (1) to change the digits that are
flashing.
Press + to increase the
flashing digits.
Press – to decrease the
flashing digits.
• Holding down + or – changes the flashing digits at high speed.
• You can set the year in the range of 2000 to 2039. The day of the week is set automatically in accordance with
the date setting.
• Pressing + or – while the Time Setting Screen is on the display causes the seconds count to be reset to 00.
• Each press of + or – while the 12-hour/24-hour Timekeeping Screen is on the display toggles between 12-hour
and 24-hour timekeeping.
3. After making the settings you want, use the SET button (2) to display the Normal Timekeeping Screen.
• The clock automatically returns to the Normal Timekeeping Screen if you leave a setting screen on the display for
about three minutes without performing any operation.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
|