USER’S GUIDE
Read this User’s Guide before you start using your P-touch.
Keep this User’s Guide in a handy place for future reference.
INTRODUCTION
GETTING STARTED
EDITINGALABEL
LABEL PRINTING
USING THE FILE MEMORY
MAINTAINNING YOUR P-TOUCH
TROUBLESHOOTING
APPENDIX
INDEX
Download from Www.Somanuals.com. All Manuals Search And Download.
LW6091001
Federal Communications Commission (FCC) Declaration of Conformity (For USA Only)
Responsible Party : Brother International Corporation
100 Somerset Corporate Boulevard
Bridgewater, NJ 08807-0911 USA
TEL : (908) 704-1700
declares that the products
Product Name :
Model Number :
Brother P-touch Electronic Labeling System
PT-2730
comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Important
• The enclosed interface cable should be used in order to ensure compliance with the limits
for a Class B digital device.
• Changes or modifications not expressly approved by Brother Industries, Ltd. could void
the user's authority to operate the equipment.
Download from Www.Somanuals.com. All Manuals Search And Download.
®
International ENERGY STAR Compliance Statement
®
The purpose of the International ENERGY STAR Program is to promote the development
®
and popularization of energy-efficient office equipment.As an ENERGY STAR Partner,
®
Brother Industries, Ltd. has determined that this product meets the ENERGY STAR
guidelines for energy efficiency.
Compilation and Publication Notice
Under the supervision of Brother Industries, Ltd., this manual has been compiled and
published, covering the latest product’s descriptions and specifications.
The contents of this manual and the specifications of this product are subject to change
without notice.
If new versions of the PT-2730 software become available, this manual may not reflect the
updated features. Therefore, you may find that the software and the contents in this manual
are different.
Trademarks and Copyrights
The Brother logo is a registered trademark of Brother Industries, Ltd.
Brother is a registered trademark of Brother Industries, Ltd.
© 2010 Brother Industries, Ltd. All rights reserved.
Microsoft, Windows Vista, and Windows are registered trademarks of Microsoft Corporation
in the United States and other countries.
Apple, Macintosh and Mac OS are trademarks of Apple Inc., registered in the United States
and other countries.
The names of other software or products used in this document are trademarks or registered
trademarks of the respective companies that developed them.
Each company whose software title is mentioned in this manual has a Software License
Agreement specific to its proprietary programs.
Any trade names and product names of companies appearing on Brother products, related
documents and any other materials are all trademarks or registered trademarks of those
respective companies.
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
How to use the P-touch................................................................................................. 4
LCD Display.......................................................................................................... 13
Inserting a Tape Cassette........................................................................................... 18
Feeding Tape.............................................................................................................. 20
Language.............................................................................................................. 22
1
2
3
4
5
6
7
Entering and Editing Text............................................................................................ 23
Entering Text from the Keyboard.......................................................................... 23
Inserting a Tab...................................................................................................... 24
8
9
1
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Setting Character Attributes.........................................................................................30
Setting Character Attributes by Label....................................................................30
Setting Character Attributes by Each Line.............................................................30
Setting Label Attributes................................................................................................35
Setting Bar Code Parameters................................................................................50
Printing Multiple Copies.........................................................................................54
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Error Messages........................................................................................................... 75
INDEX.................................................................................................... 79
1
2
3
4
5
6
7
8
9
3
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
I
How to use the P-touch
„
Create a label with the P-touch
1
GETTING STARTED
Prepare the P-touch.
P. 11
2
CREATING A LABEL
• Entering and Editing text.
In addition to entering text, the P-touch has a
large range of formatting options.
• Entering Symbols.
Create labels like these:
• Entering Accented Characters.
• Using Auto-Format Layouts.
3
LABEL PRINTING
• Printing a label.
Before printing, you can check the layout of
your label using the preview function.
• Printing from the Label collection.
Create labels like these:
How to use the P-touch
4
Download from Www.Somanuals.com. All Manuals Search And Download.
„
Create a label by connecting your P-touch to a PC
1
GETTING STARTED
This P-touch can be used as a stand alone desktop P-touch or it can be
connected to a PC/Mac and used with the included P-touch Editor software to
create more elaborate labels.
To use your P-touch connected to a computer, attach your P-touch to a
computer via the included USB cable and install the P-touch Editor software
and drivers.
• Prepare the P-touch.
• Prepare the PC.
Software Installation Guide
2
CREATING A LABEL
•
Launch the P-touch Editor Software.
Create labels like these:
• Enter the label text using P-touch
Editor.
Software Help
Software Installation Guide
1
3
LABEL PRINTING
2
3
4
5
6
7
Print the label
Software Help
Software Installation Guide
„
Printing from the Label Collection
Using the Label Collection function, labels can be created easily by selecting and
then printing designs already built into the machine.
8
9
Download from Www.Somanuals.com. All Manuals Search And HDoowwtonuloseadth.e P-touch
5
INTRODUCTION
Safety Precautions
To prevent injury and damage, important notes are explained using various symbols.
The symbols and their meanings are as follows:
Indicates a potentially hazardous situation which, if not avoided,
WARNING
could result in death or serious injuries.
Indicates a potentially hazardous situation which, if not avoided,
CAUTION
may result in minor or moderate injuries.
The symbols used in this manual are as follows:
Action NOT allowed.
DO NOT disassemble the product.
DO NOT splash the product with or
immerse the product in water.
DO NOT touch a given portion of
the product.
Mandatory action.
Safety alert.
Unplugging.
Alerts to the possibility of electrical
shock.
WARNING
P-touch
Follow these guidelines to avoid fire, electric shock, the risk of injury and/or damage.
DO NOT allow the P-touch to get wet in
any way.
DO NOT touch any metal parts near the
print head. The print head becomes very
hot during use and remains very hot
immediately after use. Do not touch it
directly with your hands.
DO NOT disassemble the P-touch.
For inspection, adjustment, and repair
of the printer, contact the retail outlet
where the P-touch was purchased or
your local authorized service centre.
Plastic bags are used in the packaging
of your printer. To avoid danger of
suffocation, keep these bags away
from babies and children.
Disconnect the AC adapter and remove
batteries immediately and stop using
when you notice abnormal odour, heat,
discolouration, deformation or anything
unusual while using or storing it.
To prevent damage, do not drop or hit
the P-touch.
DO NOT use the P-touch with a foreign object in it. If water, metallic substance or
any foreign object enters the P-touch , disconnect the AC adapter and remove
batteries, and contact the retail outlet where the P-touch was purchased or your
local authorized service centre.
Safety Precautions
6
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Battery
Follow these guidelines to avoid liquid leakage, heat, battery rupture or personal injury.
DO NOT throw into fire, heat up, short-circuit, recharge, or disassemble the
batteries.
AC adapter
Follow these guidelines to avoid fire, damage, electric shock, failure or the risk of injury.
Always use the specified voltage (220-
240V) and the suggested AC adapter.
Failure to observe this may result in an
accident or damage. Brother shall not
assume any responsibility for any
accident or damage resulting from not
using the specified AC
adapter,adapter cord and USB cable.
Don't connect the enclosed AC
adapter, adapter cord, power plug and
USB cable to other products.
DO NOT touch the AC adapter or
power plug with wet hands.
DO NOT use the AC adapter in places
of high humidity such as bathrooms.
DO NOT use a damaged adapter cord
or power plug.
DO NOT place heavy objects on,
damage or modify the adapter cord or
plug. Do not forcibly bend or pull the
adapter cord.
DO NOT drop, hit or otherwise
damage the AC adapter.
Unplug the AC adapter cord
immediately and stop using the
P-touch during an electrical storm.
There may be a remote risk of electric
shock from lightning.
Make sure that the plug is fully
inserted in the power outlet. Do not
use an outlet that is loose.
Tape Cutter
DO NOT touch the blade of the cutter
unit.
1
2
3
4
5
6
7
8
9
Safety Precautions
7
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Battery
CAUTION
Follow these guidelines to avoid liquid leakage, heat or battery rupture.
DO NOT use old and new batteries
together.
DO NOT set the positive and negative
end in the wrong position.
DO NOT mix alkaline batteries with
other type batteries.
Remove the batteries if you do not
intend to use the P-touch for an
extended period of time.
AC adapter
If you do not intend using the P-touch
for an extended period of time, please
disconnect the AC adapter from the
power outlet.
Always hold the AC adapter when
disconnecting from the power outlet.
Tape Cutter
Follow these guidelines to avoid minor personal injury and damage to the printer.
DO NOT open the tape compartment
cover when operating the cutter unit.
DO NOT apply excessive pressure to
the cutter unit.
P-touch
Follow these guidelines to avoid minor personal injury and damage to the
P-touch.
Place the P-touch on a flat, stable
surface such as a desk.
DO NOT place any heavy objects on
top of the P-touch.
DO NOT leave the P-touch within
reach of children with the tape
compartment cover open.
To prevent injuries, be careful not to
put your fingers in the areas shown in
the illustrations.
Safety Precautions
8
Download from Www.Somanuals.com. All Manuals Search And Download.
General Precautions
• DO NOT install this machine near any device that will cause electromagnetic
interference.This machine may malfunction if left near a television, radio, etc.
• DO NOT use the P-touch in any way or for any purpose not described in this guide. Doing
so may result in accidents or damage the machine.
•
DO NOT put any foreign objects into the tape exit slot, AC adapter connector or USB port, etc.
• DO NOT touch the print head with your fingers.Use the optional print head cleaning
cassette (TZ-CL4), the self-cleaning function of the printer or a soft wipe (e.g. a cotton
•
• DO NOT place the P-touch in direct sunlight, near heaters or other hot appliances, in any
location exposed to extremely high or low temperatures, high humidity, or dusty locations.
Standard operating temperature range: 50°F to 95°F.
• DO NOT leave any rubber or vinyl on the printer for an extended period of time, otherwise
the printer may be stained.
• Depending on the environmental conditions and the applied settings, some characters or
symbols may be difficult to read.
•
Use only Brother TZ tapes with this machine. Do not use tapes that do not have the
mark.
• DO NOT pull or apply pressure to the tape in the cassette. Otherwise the tape cassette or
printer may be damaged.
• DO NOT try to print labels using an empty tape cassette or without a tape cassette set in
the P-touch. Doing so will damage the print head.
• DO NOT attempt to cut the tape while printing or feeding since this will damage the tape.
• It is recommended that you use the USB cable supplied with the P-touch. Should another
USB cable need to be used, ensure it is of high quality construction.
• Be careful not to scratch the CD-ROM. Do not place the CD-ROM in any location exposed
to high or low temperatures. Do not place heavy objects on the CD-ROM or bend it.
• The software on the CD-ROM is intended for use with the P-touch and may be installed
on more than one PC.
1
• We strongly recommend that you read this User’s Guide carefully before using your
P-touch, and then keep it nearby for future reference.
2
3
4
5
6
7
• Depending on the location, material, and environmental conditions, the label may unpeel
or become irremovable, the colour of the label may change or be transferred to other
objects. Before applying the label, check the environmental condition and the material.
• DO NOT expose the tape cassettes to direct sunlight, high temperatures, high humidity,
or dust. Store tape cassettes in a cool, dark place. Use the tape cassettes soon after
opening the tape cassette package.
• Markings made with oil-based or water-based ink may be visible through a label affixed
over them. To hide the markings, use two labels layered on top of each other or use a dark-
coloured label.
• Any data stored in memory will be lost due to failure or repair of the P-touch, or if the
batteries expire.
• When power is disconnected for more than two minutes, all text and format settings
will be cleared. Any text files stored in the memory and clock settings will also be
cleared.
8
9
• Note that Brother Industries, Ltd does not assume responsibility for any damage, etc.
arising from failure to follow the precautions listed.
General Precautions
9
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Symbols Used in this Guide
The following symbols are used throughout this guide to indicate additional information.
This symbol indicates information or directions that may result in damage or
injury if ignored, or operations that will result in errors.
:
This symbol indicates information or directions that may help you understand
and use the P-touch more efficiently.
:
Symbols Used in this Guide
10
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED
Unpacking Your P-touch
Check that the package contains the following before using your P-touch.
P-touch PT-2730
Starter Tape Cassette
CD-ROM
USB cable
AC adapter
User’s Guide
The adapter plug may differ by country.
The User's Guide may be provided on CD,
not printed.
1
Software Installation Guide
You can download the PDF version
of the User's guide, please go to
2
3
4
5
6
7
The Software Installation Guide may be
provided on CD, not printed.
You can download the PDF version
of the Software Installation Guide,
please go to
8
9
Download from Www.Somanuals.com. All Manuals Search AndUDnpoawckninlgoaYdou.r P-touch
11
GETTING STARTED
General Description
Tape cassette compartment
Tape compartment cover
LCD display
Tape viewer
Tape exit slot
Keyboard
Print head
Tape cutter Release lever
When shipped from the factory, the LCD display is covered with a protective sheet to
prevent damage. Remove this sheet before using the P-touch.
AC adaptor connector
Battery compartment
cover
Battery case
USB port
General Description
12
Download from Www.Somanuals.com. All Manuals Search And Download.
LCD Display & Keyboard
LCD Display
4
5
6
7
8
9
10
1
2
3
1. Line number
5.~8. Style guidance
Indicates line number within the label
layout.
Indicates the current font (5),
character size (6), character style (7)
and frame (8) settings.
2. Cursor
9. Tape length
Characters are entered to the left of
the cursor. Indicates the current data
input position.
Indicates the tape length for the text
entered.
3. Return mark
10. Cursor selection
Indicates the end of a line of text.
4. Caps mode
Use the
items and the
change the settings.
and
keys to select menu
and keys to
Indicates that the Caps mode is on.
the back light on / off.
1
2
3
4
5
6
7
8
9
LCD Display & Keyboard
Download from Www.Somanuals.com. All Manuals Search And Download.
13
GETTING STARTED
Key Names and Functions
The default language is "English".
6. Print
1. Power
Turns the P-touch on and off.
2. Cursor (
• Prints the current label design onto
the tape.
• Opens the Print Options menu when
used in combination with the Shift
key.
)
• Moves the cursor in the direction of
the arrow.
• Use the
clock settings.
3. OK
Selects the displayed option.
4. Escape
and
keys to change
7. Preview
• Displays a preview of the label.
• Feeds 23 mm of blank tape and then
automatically cuts the tape when
used in combination with the Shift
key.
Cancels the current command and
returns the display to the data entry
screen or the previous step.
8. Display
Use this to change the display patterns
of text entry screen and clock display.
5. Label Collection
Enables label collections to be
selected and printed.
9. File
Enables frequently used labels in the
file memory to be printed, opened,
saved, or deleted.
LCD DispDlayow& nKeloybaodarfdrom Www.Somanuals.com. All Manuals Search And Download.
14
10. Text
• Enables character attributes for the
16. Shift
Use this key in combination with the
label to be set.
letter and number keys to type
uppercase letters or the symbols
indicated on the number keys.
• Character attributes can be set for
each line of the label when the Text
menu is opened in combination with
the Shift key.
17. Symbol
Use this to select and enter a symbol
from a list of available symbols.
11. Label
Enables label attributes for the label to
be set.
18. Backspace
Deletes the character to the left of the
cursor.
12. Setup
Enables operating preferences (Bar
Code, Time & Date,LCD Contrast,
etc.) for the P-touch to be set.
19. Enter
• Enters a new line when entering text.
• Enters a new block when used in
combination with the Shift key.
13. Clear
Clears all text entered, or all text and
current label settings.
20. Time
• Enters the selected date / time to the
position of the cursor in the text entry
screen.
• Clock display appears when used in
combination with the Shift key.
14. Character
• Use these keys to type letters or
numbers.
• Uppercase letters and symbols can
be entered using these keys in
combination with the Caps or Shift
key.
21. Auto-Format
Enables labels to be created using
pre-defined templates or block
formats.
15. Caps
Turns Caps mode on and off.
22. Space
1
• Enters a blank space.
• Returns a setting to the default
value.
2
3
4
5
6
7
23. Accent
Use this to select and enter an
accented character.
8
9
LCD Display & Keyboard
Download from Www.Somanuals.com. All Manuals Search And Download.
15
GETTING STARTED
Power Supply
Battery
After making sure that the power is off, remove the
battery compartment cover on the back of the
machine. If the batteries are already in the
machine, remove them.
1
Make sure that the power is turned off when
replacing batteries.
Insert eight new AA-size alkaline batteries (LR6),
making sure that the positive (+) and negative (-)
ends of the batteries match the positive (+) and
negative (-) marks inside the battery compartment.
2
Always replace all eight batteries at the same
time using brand new ones.
Attach the battery compartment cover by inserting
the three hooks at the bottom into the slots on the
machine, then pushing down firmly until it snaps
into place.
3
• Remove the batteries if you do not intend to use the P-touch for an extended period of time.
• When power is disconnected for more than two minutes, all text and format settings will be
cleared. Any text files stored in the memory and clock settings will also be cleared.
Power Supply
16
Download from Www.Somanuals.com. All Manuals Search And Download.
AC Adapter
Connect the AC adapter directly to the P-touch.
Insert the plug on the AC adapter cord into the connector marked DC IN 9-9.5V
on the P-touch.
1
Insert the AC adapter plug into a standard electrical outlet.
2
• Turn the P-touch off before disconnecting the AC adapter.
• Do not pull or bend the AC adapter cord.
To safeguard and backup the P-touch's memory and clock setting, when the AC adapter is
unplugged it is recommended to have AA-size alkaline batteries (LR6) installed into the
machine.
1
WARNING
• Use only the adapter, which is designed exclusively for your P-touch. Failure to observe
this may result in an accident or damage. Brother shall not assume any responsibility for
any accident or damage resulting from not using the specified AC adapter.
• Do not connect the AC adapter to a non-standard electrical outlet. Failure to observe this
may result in an accident or damage. Brother shall not assume any responsibility for any
accident or damage resulting from not using a standard electrical outlet.
2
3
4
5
6
7
CAUTION
• Disconnect the AC adapter from the P-touch and electrical outlet when you do not intend
to use the P-touch for an extended period.
• When power is disconnected for more than two minutes, all text and format settings will
be cleared. Any text files stored in the memory will also be cleared.
8
9
Power Supply
17
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED
Inserting a Tape Cassette
Tape cassettes of 3.5mm, 6mm, 9mm, 12mm, 18mm, or 24mm width can be used in
your P-touch. Use only Brother tape cassettes with the
mark.
• If the new tape cassette has a cardboard stopper, be sure to
remove the stopper before inserting the cassette.
• If the ink ribbon is loose, use your finger to wind the toothed
wheel in the direction of the arrow as shown on the tape cassette.
Check that the end of the tape is not bent and
that it passes through the tape guide. If the
tape is not passed through, pass it through
the tape guide referring to the illustration.
End of tape
1
2
Tape guide
After making sure that the power is off, lift open the
tape compartment cover. If there is already a tape
cassette in the machine, remove it by pulling it
straight up.
Inserting a Tape Cassette
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Insert the tape cassette into the tape
compartment, with the end of the tape
facing the machine's tape exit slot, and
press firmly until you hear a click.
When inserting the tape cassette,
3
4
make sure that the tape and ink
ribbon do not catch on the print head.
Tape exit slot
Close the tape compartment cover.
Make sure that the release lever is up when closing the
tape compartment cover. The tape compartment cover
cannot be closed if the release lever is pressed down.
• Be sure to feed tape to remove any slack in the tape and ink ribbon after inserting the tape
cassette, by holding down the Shift key and pressing the Preview key.
• Do not pull the label coming out of the tape exit slot. Doing so will cause the ink ribbon
to be discharged with the tape.
• Store tape cassettes in a cool dark location, away from direct sunlight and high temperature,
high humidity, or dusty locations. Use the tape cassette as quickly as possible after opening
the sealed package.
1
Turning Power On/Off
2
3
4
5
6
7
Press the Power key to turn the P-touch on.
Press the Power key again to turn the P-touch off.
• Your P-touch has a power saving function that automatically turns itself off if no key is
pressed within a certain time under certain operating conditions. Refer to the Auto Power-Off
Time table below for details.
• If the batteries are installed or the P-touch is connected to an electrical outlet by the AC
adapter, the previous session’s information is displayed when the power is turned on.
zAuto Power-Off Timez
P-touch only
Connected to PC
8
9
With AC adapter
With battery
8 hours
8 hours
No operation for 1 hour after
connection to USB.
5 minutes
Turning Power On/Off
19
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED
Feeding Tape
Feed & Cut
The Feed & Cut function feeds 23mm of blank tape then cuts the tape.
• Be sure to feed tape to remove any slack in the tape and ink ribbon after inserting the tape
cassette.
• Do not pull the label coming out of the tape exit slot. Doing so will cause the ink ribbon
to be discharged with the tape.
• Do not block the tape exit slot during printing or when feeding tape. Doing so will cause the
tape to jam.
Hold down the Shift key and press the Preview key.
"Feed & Cut?" will appear on the LCD display.
1
Using the
Enter
or
key to select the "Feed & Cut" option and then press either OK or
2
.
The message "Feeding Tape... Please Wait" appears while the tape is fed, and
then the tape is cut.
To exit or cancel this function press Escape
.
Feed Only
This function will advance the tape approximately 23 mm resulting in a blank label
sticking out of the tape cassette. This action is recommended when using Fabric and
Extra Strength Adhesive tapes, which should be cut using scissors.
Hold down the Shift key and press the Preview key.
"Feed & Cut?" will appear on the LCD display.
1
Using the
Enter key.
or
key to select the "Feed Only" option and then press either OK or
2
The message "Feeding Tape... Please Wait" appears while the tape is fed.
To exit or cancel this function press Escape
.
Feeding Tape
20
Download from Www.Somanuals.com. All Manuals Search And Download.
LCD Display
LCD Contrast
You can change the contrast setting of the LCD display to one of five levels (+2, +1, 0,
-1, -2) to make the screen easier to read. The default setting is “0”.
Press the Setup key to display the Setup menu, select “LCD Contrast” using the
1
or
key, and then press the OK or Enter key.
Select a contrast level using the
The screen contrast changes each time you press the
to set the most suitable contrast.
or key.
2
3
or
key, allowing you
Press the OK or Enter key.
• Press the Escape key to return to the previous step.
• Pressing the Space key on the contrast setting screen sets the contrast to the default value “0”.
Display Mode
You can change the display mode to your preferable style by pressing the Display key
repeatedly. You can select from three text entry screens (guidance + 2 text lines, 3 text
lines, guidance + 1 line) and clock display.
Text entry screen
Clock display
1
2
3
4
5
6
7
3 lines
guidance + 2 lines
guidance + 1 line
• You can also change the clock display to the text entry screen (guidance + 2 text lines) by
pressing any other key on the keyboard besides the Power key.
• For adjusting the clock to current date and time, refer to “Clock Setting” on page 45.
8
9
LCD Display
21
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED
Back Light
You can change the back light setting either to ON or OFF.
The display is easier to see with the back light ON. The default setting is "ON".
Press the Setup key to display the Setup menu, select "Backlight" using the
1
or
key, and then press the OK or Enter key.
Select "ON" or "OFF" using the
or
key.
2
3
Press the OK or Enter key.
Power can be saved when the back light is turned off.
Setting Language and Unit
Language
Press the Setup key to display the Setup menu, select "Language" using the
key, and then press the OK or Enter key.
or
1
2
S
elect a language for menu commands and messages shown on the LCD display by
using the or key.
The language can be selected from "Český", "Dansk", "Deutsch", "English", "Español",
"Français", "Hrvatski", "Italiano", "Magyar", "Nederlands", "Norsk", "Polski",
"Português", "Română", "Slovenski", "Slovenský", "Suomi", "Svenska" or "Türkçe".
Press the OK or Enter key.
3
Press the Escape key to return to the previous step.
Unit
Press the Setup key to display the Setup menu, select "Unit" using the
key, and then press the OK or Enter key.
or
key.
1
Select a unit for dimensions shown on the LCD display by using the
Either "mm" or "inch" can be selected.
or
2
3
Press the OK or Enter key.
The default setting is "mm". Press the Escape key to return to the previous step.
Setting Language and Unit
22
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING A LABEL
Entering and Editing Text
Entering Text from the Keyboard
The keyboard of your P-touch can be used in the same way as a standard computer
keyboard.
Using Text Reminder
When a character is entered, the machine remembers character sequences beginning
with the character entered from a history of all printed character sequences to date, and
displays a list of options from which to select.
Enter "c".
1
The machine displays the last word printed begining
with the letter “c” such as “computer".
2
Press the OK key to display other word options that match the entered character.
3
Press the
or
key to select the desired word.
Press the OK or Enter key.
The selected character word will then appear on the text line.
4
Text Reminder settings can be changed by pressing the Setup key.
Deleting Text Reminder Memory
1
Press the Setup key.
1
2
3
4
5
6
7
Press the
key.
or
key to select "Text Reminder", and then press the OK or Enter
2
Press the
key.
or
key to select "Clear Memory", and then press the OK or Enter
3
"Clear All Text Reminder Memory ?" is then displayed.
4
5
Press the OK or Enter key.
All text options in memory will be deleted.
8
9
Entering and Editing Text
23
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING A LABEL
Adding a New Line
To end the current line of text and start a new line, press the Enter key. A return mark
appears at the end of the line and the cursor moves to the start of the new line.
• There is a maximum number of lines of text that can be entered for each tape width. A
maximum of 7 lines can be entered for 24mm tape,5 lines for 18mm tape, 3 lines for 12mm
tape, 2 lines for 9mm and 6 mm tape, and 1 line for 3.5mm tape.
• If you press the Enter key when seven lines already exist, an error message is displayed.
• To change the character attribute of each line, refer to “Setting Character Attributes by Each
Adding a New Block
To create a new block of text/lines to the right of your current text, press the Enter key
while holding down the Shift key. A
mark will appear at the end of the block and the
cursor moves to the start of the new block.
A maximum of 5 blocks can be entered in one label.
Moving the Cursor
• Press the
• To move the cursor to the beginning or end of the current line, hold down the Shift
key and then press the or key.
• To move the cursor to the very beginning or end of the text, hold down the Shift key
,
,
or
key to move the cursor one space or line.
and then press the
or
key.
Inserting Text
To insert additional text into an existing line of text, move the cursor to the character to
the right of the position where you want to start inserting text and then enter the
additional text. The new text is inserted to the left of the cursor.
Inserting a Tab
To insert a tab space between the existing line of text, move the cursor where you wish
to add a tab and press the Setup key to open the Setup menu, select "Tab" by using
or
keys, and then press the OK or Enter key. A mark appears to indicate the
position which the tab space will be entered.
Entering and Editing Text
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Deleting Text
„
Deleting one character at a time
To delete a character from an existing line of text, move the cursor to the character to
the right of the position you want to start deleting text and then press the Backspace
key. The character to the left of the cursor is deleted each time the Backspace key is
pressed.
If you hold down the Backspace key, the characters left of the cursor are deleted continuously.
„
Deleting all text at once
Use the Clear key to delete all text at once.
Press the Clear key.
The Clear options are displayed.
1
Using the
or
key, select “Text Only” to delete all
2
text while retaining the current format settings, or
select “Text & Format” to delete all text and format
settings.
Press the Escape key to return to the text entry screen,
without erasing (or clearing) text or format.
Press the OK or Enter key.
All text is deleted. All format settings are also deleted
if Text & Format was selected.
3
1
2
3
4
5
6
7
8
9
Entering and Editing Text
25
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING A LABEL
Entering Symbols
In addition to the symbols available on the keyboard, there are various symbols
(including international and extended ASCII characters) available with the symbol
function.
To enter a symbol, use the Symbol function (see below).
Alternatively, hold down the Shift key and then press a key on the keyboard to enter
the symbol printed on the selected key's upper-right corner.
Entering Symbols Using the Symbol Function
Press the Symbol key.
A list of symbol categories and symbols in that category is displayed.
1
The last symbol entered is selected in the displayed list.
Select a symbol category (Punctuation, Business, Mathematics, etc.) using the
2
or
key or by pressing the Symbol key repeatedly, and then select a symbol
using the
or key.
Press the OK or Enter key.
The selected symbol is inserted into the line of text.
3
Press the Escape key to return to the previous step.
Entering Symbols
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Symbol Update Function
You can create your personal category of symbols by using the Symbol Update
Function. The "Personal category" will appear first when selecting the symbols to help
you locate the desired symbols quickly.
Press the Setup key to display the Setup menu, and
1
then select "Symbol Update" using the
or
key.
Press the OK or Enter key to display the Symbol
Update screen, and then select "On" to create your
2
3
4
personal category by using the
or
key.
Press the OK or Enter key to apply the setting.
The screen returns to the text entry screen.
Enter the symbol you wish to add to your personal
Category.
Press the Symbol key.
The "Personal category" appears, including the
symbol entered in step 4.
5
1
2
3
4
5
6
7
• Up to 20 symbols can be added to the "Personal category". The oldest symbol will be deleted
from the category when the symbols added to the "Personal category" exceed 20 symbols.
• To stop using the Symbol Update Function, select "Off" in the Symbol Update screen.
8
9
Download from Www.Somanuals.com. All Manuals Search And DowEnnlotearindg. Symbols
27
EDITING A LABEL
Category
zSymbol Listz
Symbols
Punctuation
Business
Mathematics
Brackets
Arrows
Unit
International
Number
Pictograph
Electrical
Audio_Visual
Signs
Communication
Vehicle
Sports
Nature
Others
The use of the CE mark is strictly governed by one or more European Council directives. Ensure
that any labels you produce which use this mark conform with the relevant directives.
Entering Symbols
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Entering Accented Characters
The P-touch can display and print a set of accented characters such as other language
specific characters.
Enter the character you wish to change to an accented character.
1
Caps mode can be used with the Accent function.
Press the Accent key.
The character you entered will change to an accented character.
2
Press the Accent key repeatedly until the desired accented character is selected,
3
or select it by using the
or
key.
The order of accented characters displayed will differ depending on the selected LCD
language.
Press the OK or Enter key.
The selected accented character is inserted into the line of text.
4
• Press the Escape key to return to the previous step.
• Refer to the Accented Character List table for a complete list of all accented characters
available.
zAccented Character Listz
Character
Accented Characters
Character
Accented Characters
1
a
A
c
n
N
o
O
r
R
s
S
t
T
u
U
y
Y
z
2
3
4
5
6
7
C
d
D
e
E
g
G
i
I
k
K
l
L
8
9
Z
Download from Www.Somanuals.com. All Manuals SearchEAnntedrinDg oAcwcnenloteaddC.haracters
29
EDITING A LABEL
Setting Character Attributes
Setting Character Attributes by Label
Using the Text key, you can select a font and apply size, width, style, line, and
alignment attributes.
Press the Text key.
The current settings are displayed.
1
Select an attribute using the
using the or key.
or
key, and then set a value for that attribute
2
3
Press the OK or Enter key to apply the settings.
New settings are NOT applied if you do not press the OK or Enter key.
• Press the Escape key to return to the previous step.
• Press the Space key to set the selected attribute to the default value.
• Refer to the Setting Options table for a list of all available settings.
• Small characters may be difficult to read when certain styles are applied (e.g. Shadow + Italic).
Setting Character Attributes by Each Line
When a label consists two or more lines of text, you can set different value of character
attributes (font, size, width, style, line and alignment) for each line.
Move the cursor to the line you wish to change the
character attribute by using the
the Text key while holding down Shift key to display the
attributes. ( on the screen indicates that you are now
or
key. Next, press
applying the attribute for that specific line only.)
When different value of attribute is set for each line, the value
will be displayed as **** when you press the Text key. When
you change the setting on this screen by using the
or
key,
the same change will be applied to all lines of the label.
Setting Character Attributes
30
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING A LABEL
Attribute
Value
Auto
Result
When Auto is selected, the text is
automatically adjusted to print in the largest
size available for each tape width.
48pt
42pt
36pt
24pt
18pt
12pt
9pt
Size
6pt
x2
x3/2
x1
Width
x2/3
x1/2
Setting Character Attributes
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Attribute
Value
Result
Normal
BLD
(Bold)
OUT
(Outline)
SHD
(Shadow)
SLD
(Solid)
ITL
(Italic)
Style
I+BLD
(Italic Bold)
I+OUT
(Italic Outline)
I+SHD
(Italic Shadow)
1
I+SLD
(Italic Solid)
2
3
4
5
6
7
VRT
(Vertical)
Off
UND
(Underline)
Line
STR
(Strikeout)
8
9
Download from Www.Somanuals.com. All Manuals Search ASnedttiDngoCwhnarlaocatedr.Attributes
33
EDITING A LABEL
Attribute
Value
Left
Result
Center
Right
Align
(Alignment)
Just
(Justify)
Setting Auto Fit Style
When "Size" is set to "Auto" and "Length" is set to a specific length, you can select the
way of reducing the text size to fit within the label length.
When "Text Size" is selected, the total text size is modified to fit within the label.
When "Text Width" is selected, the text width will be reduced to the size of x1/2 setting.
(If further size reduction is required to fit the text into the selected label length, the total
text size will be modified after reducing the text width to x1/2 setting.)
Press the Setup key to display the Setup menu, Select "Auto Fit Style" using the
1
or
key, and then press the OK or Enter key.
The Auto Fit Style screen is displayed.
Select the style using the or key.
2
3
Press the OK or Enter key to apply the setting.
• Press the Escape key to return to the previous step.
• Press the Space key to set the style to the default setting ("Text Size").
Setting Character Attributes
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Label Attributes
Using the Label key, you can create a label with a frame around the text and specify
the label length and tab length. (Cut Options which may be needed when printing a
page 57.)
Press the Label key.
The current settings are displayed.
1
Select an attribute using the or key, and then set
2
a value for that attribute using the
or
key.
• When setting the tab length, hold down the or key
to change the value faster.
• When setting the label length, refer to “Adjusting the
Press the OK or Enter key to apply the settings.
3
New settings are NOT applied if you do not press the OK
or Enter key.
• Press the Escape key to return to the previous step.
• Press the Space key to set the selected attribute to the default value.
• Refer to the Setting Options table for a list of all available settings.
1
2
3
4
5
6
7
8
9
Download from Www.Somanuals.com. All Manuals Search And SDeottwingnlLoaabedl.Attributes
35
Attribute
Value
Result
13
14
15
16
17
18
19
20
Frame
1
The length of the label can be set within the range 30mm -
300mm. When Auto is selected, the length of the label is
automatically adjusted based on the amount of text entered.
Length
2
3
4
5
6
7
The length of the tab can be set within the range 0mm -100mm.
Tab Length
The default setting is 50mm
.
8
9
Download from Www.Somanuals.com. All Manuals Search And SDeottwingnlLoaabedl.Attributes
37
EDITING A LABEL
Using Auto-Format Layouts
Using the Auto-Format function you can quickly and easily create labels for a variety of
purposes, such as file tabs, equipment labels, name badges, etc. Simply select a layout
from the templates or block layouts, enter the text and apply formatting as desired.
Symbols and accented characters can also be used in auto-format layouts.
Using Templates - Example creating an Asset Tag
Press the Auto-Format key to display the Auto-Format screen, and then select
1
"Templates" using the
or
key.
Press the OK or Enter key
The last template used is displayed.
.
2
Select a template using the or
key.
3
4
Press the OK or Enter key
.
The Style screen is displayed.
Select an attribute using the or key, and then set
a value for that attribute using the or key.
5
6
Press the OK or Enter key
.
The Bar Code Setup screen is displayed.
The Bar Code Setup screen is displayed only when a
layout containing a bar code is selected.
Select an attribute using the or key, and then set
7
a value for that attribute using the
or
key.
The "C-Digit" (Check Digit) attribute is only available
for the CODE39, I-2/5 and CODABAR protocols.
Using Auto-Format Layouts
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Press the OK or Enter key
The template text entry screen is displayed.
.
8
• Caps mode can be used when entering text.
• The “Text Reminder” function (predictive text) is also
enabled when entering text with the Auto-Format
function. Refer to “Entering and Editing Text”
Enter the text and then press the OK or Enter key
Repeat this for each text field.
.
9
After all text fields are entered, the print menu is
displayed when the OK or Enter key is pressed.
Select "Print" using the
the label.
or
key and then press the OK or Enter key to print
10
• Select "Edit" to change the text data or style settings.
• Select "Save" to store the label in a file memory.
• Select "Cancel" to exit the Auto-Format function.
• Select “Print Options” to set the print settings.
• Press the Escape key to return to the previous step.
• On the Style and Bar Code Setup screens, press the Space key to change the selected attribute
to the default value.
• Refer to the Templates table for a list of available templates.
• To print multiple copies, sequentially numbered copies, or a mirror image of the label, with
the print menu displayed hold down the Shift key and press the Print key to display the Print
Options menu.
1
2
3
4
5
6
7
• If the width of the current tape cassette does not match the set width for the selected layout,
an error message is displayed when you try to print the label. Press the Escape key or any other
key to clear the error message, and insert a tape cassette of the correct width.
• If the number of characters entered exceeds the limit, “Text Too Long!” is displayed when the
OK or Enter key is pressed. Press the Escape key or any other key to clear the error message,
and edit the text using fewer characters.
• When using the Auto-Format function the label is cut with a margin on the left and right ends
• Cutting is disabled when “Cut Option” is set to Special Tape.
8
9
Download from Www.Somanuals.com. All Manuals Search AUnsdinDg oAuwton-lFooarmda.t Layouts
39
EDITING A LABEL
Attribute
zTemplatesz
Value
Details
Binder Spine 1
(24 mm x 219 mm)
(18 mm x 219 mm)
Binder Spine 2
File Folder Tab
(12 mm x 82 mm)
(12 mm x 42 mm)
Divider Tab
(Hanging Folder)
Asset Tag
Bin Box
(18 mm x 70 mm)
(18 mm x 76 mm)
Template Name
Equipment Label
Faceplate (VRT)
(24 mm x 58 mm)
(12 mm x 70 mm)
Cable Wrap 1
Cable Wrap 2
(24 mm x 39 mm)
(18 mm x 39 mm)
Using Auto-Format Layouts
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Attribute
Value
Details
Address Label 1
(24 mm x 70 mm)
(18 mm x 70 mm)
(24 mm x 72 mm)
Address Label 2
Name Badge 1
Name Badge 2
(18 mm x 72 mm)
(12 mm x 72 mm)
(6 mm x 113 mm)
(3.5 mm x 113 mm)
(18 mm x 140 mm)
(9 mm x 42 mm)
Template Name
Name Badge 3
CD Case Spine 1
CD Case Spine 2
VHS Spine
1
2
3
4
5
6
7
MiniDV Spine
8
9
Download from Www.Somanuals.com. All Manuals Search AUnsdinDg oAuwton-lFooarmda.t Layouts
41
EDITING A LABEL
Using Block Layouts
Press the Auto-Format key to display the Auto-Format screen, and then select
1
“Block Layouts” using the
or
key.
Press the OK or Enter key to display the Tape Width screen, and then select a
tape width using the or key.
2
3
Press the OK or Enter key.
When the tape width has not changed, the last block layout selected is displayed.
When the tape width has changed, the default layout for the new tape width is
displayed.
Select a block layout using the
or
key.
4
5
Press the OK or Enter key.
The Style screen is displayed.
Select an attribute using the or key, and then set
a value for that attribute using the or key.
6
7
Press the Space key to set the selected attribute to the
default value.
Press the OK or Enter key.
The block layout text entry screen is displayed.
• Caps mode can be used when entering text.
• The “Text Reminder” function (predictive text) is also
enabled when entering text with the Auto-Format
function. Refer to “Entering and Editing Text” on
page 23 for details on predictive text.
Enter text and then press the OK or Enter key.
Repeat for each text field.
After all text fields are completed, press the OK or
Enter key to display the print menu.
8
9
Select "Print" using the
or
key and then press the OK or Enter to print the label.
• Select "Edit" to change the text data or style settings.
• Select "Save" to store the label in a file memory.
• Select "Cancel" to exit the Auto-Format function.
• Select "Change Layout" to use a different layout.
• Select “Print Options” to set the print settings.
Using Auto-Format Layouts
42
Download from Www.Somanuals.com. All Manuals Search And Download.
• Press the Escape key to return to the previous step.
• Refer to the Block Layouts table for a list of available block layouts.
• To print multiple copies, sequentially numbered copies, or a mirror image of the label, with
the print menu displayed hold down the Shift key and press the Print key to display the Print
Options menu.
• If the width of the current tape cassette does not match the set width for the selected layout,
an error message is displayed when you try to print the label. Press the Escape key or any other
key to clear the error message, and insert a tape cassette of the correct width.
• If the number of characters entered exceeds the limit, “Text Too Long!” is displayed when the
OK or Enter key is pressed. Press the Escape key or any other key to clear the error message,
and edit the text using fewer characters.
• When using the Auto-Format function the label is cut with a margin on the left and right ends
• Cutting is disabled when “Cut Option” is set to Special Tape.
zBlock Layoutsz
Attribute
Value
Details
2LineA
2LineB
3 Line
1
2
3
4
5
6
7
1+2Line A
1+2Line B
1+3Line
1+4Line
1+5Line
Block layout
(24mm tape)
8
9
Download from Www.Somanuals.com. All Manuals Search AUnsdinDg oAuwton-lFooarmda.t Layouts
43
EDITING A LABEL
Attribute
Value
Details
2LineA
2LineB
3Line
1+2LineA
1+2LineB
1+3Line
1+4Line
1+5Line
2LineA
2LineB
Block layout
(18 mm tape)
Block layout
(12 mm tape)
3Line
1+2Line
Using Auto-Format Layouts
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Attribute
Value
Details
2LineA
Block layout
(9 mm tape)
2LineB
1+2Line
1+2Line
Block layout
(6 mm tape)
Using Time & Date Function
You can add time and date to your label by positioning the cursor on the text screen to
the position you wish to add time/date and then pressing the Time key.
Clock Setting
The time and date set in the clock setting can be used for the display on the screen,
and also for using the Time & Date function which you can add time/date to your label
in desired format.
Press the Setup key to display the Setup menu, select "Set Clock" using the
1
or
keys, and then press the OK or Enter key.
1
The Set Clock screen is displayed.
Set the year, month, date, hour and minute to the
2
2
3
4
5
6
7
current figure using the
next parameter, use the
or
or
key. To move to the
key.
You can also use the Num keys to type in the figure.
Press the OK or Enter key to apply the settings.
3
• Press the Escape key to return to the previous step.
• Press the Space key to set the format to default setting.
• The clock will activate from when the clock setting is applied.
• For the backup of clock setting, when the AC adapter is unplugged, please use AA-size
alkaline batteries.
8
9
Using Time & Date Function
45
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING A LABEL
Time & Date Format Setting
You can select from various formats of date and time to add to your label.
Also, the indication of time can be selected between analog and digital style.
The format applied in this setting will also be applied for the clock display which appears
for detail.)
Press the Setup key to display the Setup menu, select "Time & Date Format"
1
using the
or
key, and then press the OK or Enter key.
The Time & Date Format screen is displayed.
2
3
Select date or time using the
key.
or
key, and then set the format using the or
Press the OK or Enter key to apply the settings.
New settings are not applied if you do not press the OK or Enter key.
• Press the Escape key to return to the previous step.
• Press the Space key to set the format to default setting.
• Refer to the Format Options for a list of all available formats.
zTime & Date Format Optionsz
Attribute
Value
31/12/2099
31.12.2099
31-12-2099
31.December 2099
31.Dec.2099
12/31/2099
D
(Date)
12.31.2099
12-31-2099
December 31, 2099
Dec. 31, 2099
2099/12/31
2099-12-31
Using Time & Date Function
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Attribute
Value
11:59 PM
T
(Time)
23:59
The date and time used for the value is a sample setting. When a format is selected, the date and
time set in the clock setting will appear in the selected format style.
Time Stamp Setting
[Timing]
You can select whether to print the date/time of when you press the Time key or the
date/time of when you press the Print key to add to your label.
Press the Setup key to display the Setup menu, select "Time Stamp Setting"
1
using the
or
key, and then press the OK or Enter key.
Select "Timing" using the
using the or key.
or
key, and then select the value for the setting
2
3
Press the OK or Enter key to apply the settings.
• Press the Escape key to return to the previous step.
• Press the Space key to set the format to default setting.
• Refer to the Time Stamp: Timing Options for available settings.
zTime Stamp : Timing Optionsz
1
Attribute
Value
Description
2
3
4
5
6
7
Press the Time key; a clock icon will be inserted where
the cursor is positioned on the text input screen.
When you press the Print key, the latest date/time will be
printed on the label where the clock icon is positioned on
the label layout.
Auto
Timing
Press the Time key; the current date/time will be inserted
where the cursor is positioned on the text input screen.
When you press the Print key, the date/time will be
printed as shown on the input screen.
Fixed
When "Auto" is selected for the Timing setting and a clock icon is added to the text by pressing
the Time key, you can confirm what settings applied for the icon by positioning the cursor under
the clock icon, and then pressing the Time key.
8
9
Using Time & Date Function
47
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING A LABEL
[Time Stamp Format]
You can select which information to use when adding date and time to your label.
Four options (Date, Time, Date and Time or Time and Date) are available.
Press the Setup key to display the Setup menu, select "Time Stamp Setting"
1
using the
or
key, and then press the OK or Enter key.
Select "Format" using the
using the or key.
or key, and then select the value for the setting
2
3
Press the OK or Enter key to apply the settings.
• Press the Escape key to return to the previous step.
• Press the Space key to set the value to default setting.
• Refer to the Time Stamp: Format Options for available settings.
zTime Stamp : Format Optionsz
Attribute
Value
Description
Date
Date only will be printed on the label.
Date & Time
Time
The date and time will be printed on the label.
Time only will be printed on the label.
Format
Time & Date
The time and date will be printed on the label.
[Forward]
You can select whether to use a forwarded (future) date and time or the current date
and time when using the Time & Date Function.
Press the Setup key to display the Setup menu, select "Time Stamp Setting"
1
using the
or
key, and then press the OK or Enter key.
Select "Forward" using the
and time to increase, select "On" using the or key.
or key, and then to specify the amount of date
2
Using Time & Date Function
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Press the OK or Enter key. The Forward screen is
displayed. Set the amount of year, month, week, day,
hour, and minute to increase from the currently set
clock when using the Time & Date function using the
3
4
or
key. To move to the next parameter, use the
or
key.
You can also use the Num keys to type in the figure.
Press the OK or Enter key to apply the settings.
• Press the Escape key to return to the previous step.
• Press the Space key to set the format to default setting.
• Refer to the Time Stamp: Forward Options for a list of all available formats.
zTime Stamp : Forward Optionsz
Attribute
Value
Description
The time/date will be increased according to the
value selected in the Forward setting.
On
Forward
Off
Current time/date will be printed.
Creating a Bar Code Label
1
Using the Bar Code function you can create labels with one dimensional bar codes for
use with cash registers, stock control systems or other bar code reader systems, or
even asset control tags used in an asset management system.
2
3
4
5
6
7
• The P-touch is not designed exclusively for creating bar code labels. Always check that
bar code labels can be read by the bar code reader.
• For best results, print bar code labels in black ink on white tape. Some bar code readers
may not be able to read bar code labels created using coloured tape or ink.
• Use the “Large” setting for “Width” whenever possible. Some bar code readers may not
be able to read bar code labels created using the “Small” setting.
• Continuously printing a large number of labels with bar codes can overheat the print
head, which may affect printing quality.
8
9
Creating a Bar Code Label
49
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING A LABEL
Setting Bar Code Parameters
Press the Setup key to display the Setup menu, select “Bar Code Setup” using
1
the
or
key, and then press the OK or Enter key.
The Bar Code Setup screen is displayed.
Select an attribute using the
using the or key.
or
key, and then set a value for that attribute
2
3
Characters may not appear below the bar code even when "On" is selected for "Under #",
depending on the tape width being used, the number of lines entered, or the current
character style settings.
Press the OK or Enter key to apply the settings.
New settings are NOT applied if you do not press the OK or Enter key.
• The "C-Digit" (Check Digit) attribute is only available for the CODE39, I-2/5 and CODABAR
protocols
• Press the Escape key to return to the previous step.
• Press the Space key to set the selected attribute to the default value.
• Refer to the Bar Code Settings table for a list of all available settings.
zBar Code Settingsz
Attribute
Value
CODE39, CODE128, EAN-8, EAN-13,
GS1-128 (UCC/EAN-128), UPC-A, UPC-E, I-2/5 (ITF),
CODABAR
Protocol
Small
Large
On
Width
Under#
(characters printed
below bar code)
Off
Off
C.Digit
(check digit)
On
(only available for the CODE39, I-2/5
and CODABAR protocols)
Creating a Bar Code Label
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Entering Bar Code Data
Press the Setup key to display the Setup menu, select "Bar Code Input" using the
1
or
keys, and then press the OK or Enter key. The Bar Code Input screen
is displayed.
• Up to five bar codes can be entered on a label.
• Pressing the Symbol key while holding down the Shift key
will also allow you to go to "Bar Code Input".
Type in the bar code data. Special characters can be
entered in the bar code when using the CODE39,
CODABAR, CODE128 or GS1-128 (UCC / EAN-128)
protocols. When not using special characters, go to
step 5.
2
Press the Symbol key. A list of characters available for the current protocol is
displayed.
3
4
Select a character using the
or
key, then press
the OK or Enter key to insert the character in the bar
code data.
Press the OK or Enter key to insert the bar code in the
label.
5
The bar code is displayed on the text entry screen.
1
• Press the Escape key to return to the previous step.
• Refer to the Special Characters List table for a list of all available settings.
2
3
4
5
6
7
zSpecial Character Listz
CODE39
Code
CODABAR
Special Character
Code
Special Character
0
1
2
3
4
5
6
0
1
2
3
4
5
(SPACE)
8
9
Creating a Bar Code Label
51
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING A LABEL
CODE128, GS1-128 (UCC / EAN-128)
Code Special Character Code Special Character Code Special Character
0
1
(SPACE)
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
DC3
DC4
NAK
SYN
ETB
CAN
EM
2
3
4
NUL
5
6
SOH
STX
ETX
EOT
ENQ
ACK
BEL
BS
7
SUB
ESC
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
FS
GS
RS
HT
LF
VT
US
FF
DEL
CR
FNC3
FNC2
FNC4
FNC1
SO
SI
DLE
DC1
DC2
Editing and Deleting a Bar Code
• To edit the bar code data position the cursor beneath the bar code mark on the data
entry screen and then open the Bar Code Input screen. Refer to “Entering Bar Code
position the cursor beneath the bar code mark on the data entry screen and then open
on the data entry screen and press the Backspace key.
Creating a Bar Code Label
52
Download from Www.Somanuals.com. All Manuals Search And Download.
LABEL PRINTING
Label Preview
Using the Preview function you can check the layout of the label before printing.
Press the Preview key.
An image of the label is displayed on the screen.
The length of the label is shown in the lower-right corner of the screen.
Press the
Press the
or
or
key to scroll the preview to the left or right.
key to change the magnification of the preview.
• Press the Escape
,
OK or Enter key to return to the text entry screen.
• To scroll the preview to the left or right end, hold down the Shift key and press the or
key.
• To print the label directly from the preview screen, press the Print key or open the print
options screen and select a print option. Refer to "Printing a Label" below for details.
• The print preview is a generated image of the label, and may differ from the actual label when
printed.
Printing a Label
Labels can be printed once text entry and formatting is complete. Printing options
include single and multiple copies, sequential numbering and mirror-printing.
• Do not pull the label coming out of the tape exit slot. Doing so will cause the ink ribbon
to be discharged with the tape.
• Do not block the tape exit slot during printing or when feeding tape. Doing so will cause the
tape to jam.
1
• Be sure to check that there is enough tape remaining when printing several labels
continuously. If tape is running low, set fewer copies, print labels one at a time, or replace the
tape cassette.
• Striped tape indicates the end of the tape cassette. If this appears during
printing, press the Power key to turn the P-touch off. Attempting to
print with an empty tape cassette may damage the machine.
2
3
4
5
6
7
8
9
Label Preview
53
Download from Www.Somanuals.com. All Manuals Search And Download.
LABEL PRINTING
Printing a Single Copy
Make sure that the appropriate tape cassette is inserted and ready for printing.
1
Press the Print key. "Printing...Copies" is displayed
while the labels are being printed.
2
To stop printing, press the Power key to turn off the P-touch.
Messages” on page 75 for further information about error messages.
Printing Multiple Copies
Using this function you can print up to 99 copies of the same label.
Make sure that the appropriate tape cassette is inserted and ready for printing.
1
Hold down the Shift key and press the Print key to display the print options
2
screen, and then select “Copies” using the
or
key.
Press the OK or Enter key to display the Copies screen, and then select the
3
number of copies to be printed using the
the number keys.
or
key, or type the number using
Hold down the
or
key to change the number of copies faster.
Press the OK or Enter key. "Printing...Copies" is
displayed while the labels are being printed.
4
• Press the Escape key to return to the previous step.
• Unless set otherwise, the tape is automatically cut after each copy is printed. Refer to “Tape
Cutting Options” on page 57 to change this setting.
• The figures shown on the screen during printing indicate the “count / number of copies set”.
• Pressing the Space key when setting the number of copies resets the value to 1, the default.
Printing aDLaobwelnload from Www.Somanuals.com. All Manuals Search And Download.
54
Auto-numbering Labels
Using the numbering function you can create a set of sequentially numbered labels
from a single label format.
Make sure that the appropriate tape cassette is inserted and ready for printing.
1
Hold down the Shift key and press the Print key to display the print options
2
screen, and then select "Numbering" using the
or
key.
Press the OK or Enter key.
The numbering start point screen is displayed.
3
To apply auto-numbering to a bar code, select the bar code
here. After selecting the bar code you will be prompted to
enter the number of labels to be printed (step 6).
Move the cursor to the first character to be
incremented in the numbering sequence and press
the OK or Enter key.
4
5
6
The numbering end point screen is displayed.
Move the cursor to the last character to be
incremented in the numbering sequence and press
the OK or Enter key.
The number of labels to be printed is displayed.
Select the number of labels to be printed using the
or
key, or type the number using the number key.
Hold down the
labels faster.
or
key to change the number of
1
2
3
4
5
6
7
Press the OK or Enter key.
The labels are printed.
As each label is printed the number of copies printed is shown.
7
8
9
Printing a Label
55
Download from Www.Somanuals.com. All Manuals Search And Download.
LABEL PRINTING
• Press the Escape key to return to the previous step.
• The tape is automatically cut after each copy is printed. Refer to “Tape Cutting Options” on
page 57 to change this setting.
• The figures shown on the screen during printing indicate the “count / number of copies”.
• Pressing the Space key when selecting the number of copies resets the value to 1, the default.
• Auto-numbering can also be applied to bar codes. When a bar code contains an auto-
numbering sequence, no other fields in the label can contain an auto-numbering sequence.
• The auto-number portion of the label is incremented after each label is printed.
• Only one auto-numbering sequence can be used in a label.
• Any symbols or other non-alphanumeric characters in the auto-numbering sequence are ignored.
• An auto-numbering sequence can only contain a maximum of five characters.
• Letters and numbers increase as shown below:
0
A
a
Î
Î
Î
Î
1
B
b
...9
...Z
...z
Î
Î
Î
Î
0
A
a
Î
Î
Î
Î
...
...
...
...
A0
A1 ...A9
B0
Spaces (shown as underscores “_” in the example below) can be used to adjust the spacing
between characters or to control the number of digits that are printed.
_9
_Z
1_9
Î
Î
Î
10
...99
Î
Î
Î
00
AA
0_0
Î
Î
Î
...
...
...
AA ...ZZ
2_0 ...9_9
Mirror Printing
Using the mirror printing function you can create labels with the text printed in reverse
so that they can be read from the opposite side when attached to glass or other
transparent material.
Make sure that the appropriate tape cassette is inserted and ready for printing.
1
Hold down the Shift key and press the Print key to display the print options
2
screen, and then select “Mirror” using the
or
key.
Press the OK or Enter key. The message “Mirror Print?” is displayed.
3
4
Press the OK or Enter key. "Printing...Copies" is
displayed while the labels are being printed.
• Press the Escape key to return to the previous step.
• Text should be printed on clear tape when using the mirror printing function.
• The copy and auto-numbering functions cannot be used together with the mirror printing
function.
Printing aDLaobwelnload from Www.Somanuals.com. All Manuals Search And Download.
56
Tape Cutting Options
The tape cutting options allow you to specify how the tape is fed and cut when printing
labels. In particular, the “Chain” and “No Cut” options greatly reduce the amount of
wasted tape by using smaller margins and eliminating blank sections cut between
labels.
Press the Label key to display the Label menu.
1
Select "Cut Option" using the
or key.
or
key, and then set the value by using the
2
Press the OK or Enter key to apply the settings.
3
New settings are NOT applied if you do not press the OK or Enter key.
• Press the Escape key to return to the previous step.
• Refer to the Tape Cutting table for a list of all available settings.
1
2
3
4
5
6
7
8
9
Download from Www.Somanuals.com. All Manuals Search And DToawpenlCouattdin.g Options
57
LABEL PRINTING
Setting
zTape Cuttingz
Description
Example
Automatically cuts the tape after each label is
printed, leaving a margin of 24 mm on each
end.
ABC
ABC
Large
Margin
24 mm
24 mm
23 mm
Automatically cuts a piece of blank tape
before printing the first label and then cuts the
tape after each label is printed, leaving a 4
mm margin at each end of each label.
ABC
ABC
Small
Margin
4 mm
4 mm
• Automatically cuts a piece of blank tape
before printing the first label and then cuts
the tape after each label is printed, leaving
a 4 mm margin at each end of each label.
• Once the last label is printed, the tape is not
fed and cut.
23 mm
ABC ABC
Chain
4 mm
4 mm
• Prints a strip of labels with no cuts in
between.
• Pressing the Preview while holding down
Shift key will feed and cut the last label
printed.
ABC ABC
No Cut
24 mm
8 mm
• Select this setting when using special tape.
• When using Fabric Iron-On Tapes or Extra
Strength Adhesive Tapes, set "On" for
Manual Cutting before printing. After
ABC ABC
Special
Tape
24 mm
printing, remove the tape cassette from the
machine and use scissors to cut the tape.
• When using Fabric Iron-On Tapes or Extra Strength Adhesive Tapes, refer to the above
"Special Tape".
• The tape is not cut after the last label is printed when “Chain” or “No Cut” is set. Hold down
the Shift key and press the Preview key to feed and cut tape automatically, or cut the tape
manually if you are using Fabric Iron-on Tapes or Extra Strength Adhesive Tapes.
Tape Cutting Options
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Label Length
You can adjust the length of the printed label in levels of -5 to +5.
Press the Setup key to display the setup menu, select "Adjust Length" using the
1
or
key, and then press the OK or Enter key.
Select "Adjust Length" by using the
then set the value by using the or
or
key.
key, and
2
Press the OK or Enter key to apply the setting.
3
• Press the Escape key to return to the previous step.
• Press the Space key to set the value to default setting.
• Approximately 1% of the total label length will be adjusted by 1 level.
Attaching Labels
If necessary, trim the printed label to the desired shape and length using scissors, etc.
Peel the backing from the label.
1
2
3
Position the label and then press firmly from top to bottom with your finger to
attach the label.
1
2
3
4
5
6
7
• The backing of some types of tapes may be pre-cut to make it easier to peel the backing.To
remove the backing, simply fold the label lengthwise with the text facing inward, to expose
the inside edges of the backing. Next, peel off the backing one piece at a time.
• Labels may be difficult to attach to surfaces that are wet, dirty, or uneven. The labels may peel
off easily from these surfaces.
• Be sure to read the instructions provided with Fabric Iron-On Tapes, Extra Strength Adhesive
Tapes or other special tapes and observe all precautions noted in the instructions.
8
9
Adjusting the Label Length
59
Download from Www.Somanuals.com. All Manuals Search And Download.
LABEL PRINTING
Printing from the Label Collection
Printing a label from the Label Collection Stored in the Machine
these pre-designed labels saves you time.
Press the Label Collection key.
1
Select the language of the label to be printed using the
press the OK or Enter key.
or
key, and then
2
The language can be selected from "Croatian", "Czech", "Danish", "Dutch",
"English (United Kingdom)", "Finnish", "French", "German", "Hungarian", "Italian",
"Norwegian", "Polish", "Portuguese", "Romanian", "Slovak", "Slovenian",
"Spanish (Spain)", or "Swedish".
Select the category using the
or
key, and then press the OK or Enter key.
3
4
Refer to the Label Collection Lists to view all of the available labels.
The first label image is displayed.
Select a label using the
or
key, and then press the OK or Enter key.
To add the label to your "Favorites", select "Add to Favorites" using the
or
key,
and then press the OK or Enter key to register the selected label image in the Favorites
category. Registering your most frequently used label images allows you to quickly and
easily display them when needed again.
Select "Print" using the
or
key, and then press the OK or Enter key.
5
Label Collection categories are pre-set for specific tape widths. Tape widths are
referenced after the name of the Label Collection category in parentheses. For example,
to create a Shipping Label, 18 mm tape must be loaded in the machine. If the width of the
current tape cassette does not match the set width for the selected layout, an error message
is displayed when you try to print the label. Press the Escape key or any other key to clear
the error message, and insert a tape cassette of the correct width.
• Using the P-touch Update Software, additional label categories can be downloaded and new
label designs added to the machine or P-touch Editor.
how to download additional categories of labels.
Printing from the Label Collection
60
Download from Www.Somanuals.com. All Manuals Search And Download.
LABEL PRINTING
Category
Label
Caution
(24 mm tape
only)
Shipping
(18 mm tape
only)
ECO
(18 mm tape
only)
* Labels are for illustrative purposes only.
Printing from the Label Collection
62
Download from Www.Somanuals.com. All Manuals Search And Download.
LABEL PRINTING
Downloading a new Label Collection Category
®
(Windows only)
Using the P-touch Update Software, additional label collection categories can be
downloaded to your P-touch or downloaded to your PC and printed using P-touch Editor.
Furthermore, the software can be upgraded to the latest version using this tool.
• To use the P-touch Update Software, it is necessary to install it from the CD-ROM
provided.
• Refer to the "Software Installation Guide" for details on how to install the software.
• You must be connected to the internet in order to launch the P-touch Update software.
• Label Collection Designs cannot be edited.
• You may find that the software and the contents in this manual are different.
• Upon installation of the P-touch Update Software, an icon will be installed on your
desktop (or other location of your choosing) for your convenience. To check for New
Label Collection Designs, simply click the icon to launch the software.
Downloading a Label Collection Category to your P-touch
®
The following is the example for Windows Vista .
In the following steps, you will see XX-XXXX. Read "XX" as your printer name.
Turn the machine on and connect the USB cable.
1
Double-click the [P-touch Update Software] icon.
2
The following method can also be used to start the P-touch
Update Software.
Click [Start], and then select [All Programs] - [Brother
P-touch] - [P-touch Update Software].
Click the [Machine update] icon.
3
®
Downloading a new Label Collection Category (Windows only)
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Select the [Printer], ensure that [The
machine is connected correctly.] is
displayed, and then click [OK].
4
5
Select the [Language], select the check box
next to the label collection to be downloaded
and/or software to be updated, and then click
[Transfer].
Click "Click here for details" in the
upper right to open a web page with
details of a specific label collection.
Check the content to be updated, and then
click [Start] to begin the update.
1
6
2
3
4
5
6
7
8
9
®
only)
Download from Www.Somanuals.Dcoowmnl.oaAdlilnMg aanneuwaLlsabSeleCaorllcechtioAnnCdatDegoowryn(Wloianddo.ws
65
LABEL PRINTING
The screen on the right is displayed on your
computer while the software is being
7
updated screen.
The screen on the right appears on the
machine's LCD display.
Do not turn off the machine during the
update process.
Click [OK] to complete the update.
8
The display returns to the input screen when the update is complete.
9
.
• Newly downloaded label collection categories are added to
the respective "Category".
• An asterisk "*" is displayed at the end of the newly added
category.
• Downloaded label collections can be deleted using the
following procedure
.
1. Press the Label Collection key.
2. Press the
3. Press the
or
or
key, and then select the language.
key, and then select the category.
4. Press the Clear key.
• If the downloaded label collection was registered in "Favorites", it will also be deleted from
here.
• It is not possible to delete individual labels from each "Category".
• When "Download New Labels" is selected, the prompt "Connect PC, and Run P-touch
Update" is displayed.
®
Downloading a new Label Collection Category (Windows only)
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Downloading a New Label Collection Category to P-touch Editor /
Updating P-touch Editor Software
®
The following is the example for Windows Vista .
In the following steps, you will see XX-XXXX. Read "XX" as your printer name.
Double-click [P-touch Update Software].
1
• The following method can also be used to start the P-touch
Update Software.
• Click the [Start], and then select [All Programs] -
[Brother P-touch] - [P-touch Update Software].
• If a message is displayed notifying the user that the Editing
Software (P-touch Editor) is the latest version when started,
click [Yes] and then proceed to step 3.
Click the [Computer software update] icon.
2
Select the [Printer] and [Language], select
3
the check box next to the label collection to
be installed and then click [Install].
Click "Click here for details" in the
1
2
3
4
5
6
7
upper right to open a web page with
details of a specific label collection.
8
9
®
only)
Download from Www.Somanuals.Dcoowmnl.oaAdlilnMg aanneuwaLlsabSeleCaorllcechtioAnnCdatDegoowryn(Wloianddo.ws
67
LABEL PRINTING
The installed label collection will be saved to
the P-touch Editor [Label Collection] tab.
4
®
Downloading a new Label Collection Category (Windows only)
68
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE FILE MEMORY
You can store up to 99 of your most frequently used labels in the file memory. Each label is
stored as a file, allowing you to quickly and easily recall your label when needed again.
• When the file memory is full, each time you save a file you will need to overwrite one of your
stored files.
Storing a Label into Memory
After entering the text and formatting the label, press the File key to display the
File screen.
1
Select "Save" using the
or
key.
2
3
Press the OK or Enter key. A file number is displayed.
A label text is also displayed if a label is already stored in that file number.
Select a file number using the
to save the label under the selected file number.
or
key, and then press the OK or Enter key
4
The file is saved and the screen returns to the text entry screen.
When there is already a stored file in the selected number, the data will be overwritten by
the file you try to save.
• Press the Escape key to return to the previous step.
• A maximum of 280 characters can be saved in each file. However, this number may depend
upon the characters or symbols used. Up to 99 files can be saved.
• To store a label created by using the Auto-Format Layouts, refer to “Using Auto-Format
1
Opening a Stored Label File
2
3
4
5
6
7
Press the File key to display the File screen.
1
2
3
Select "Open" using the
or
key.
Press the OK or Enter key. The file number of a stored label is displayed.
The label text is also displayed to identify the label.
Select a file number using the
or
key, and then press the OK or Enter key
4
to open the selected file. The file is opened and displayed on the text entry screen.
8
9
Press the Escape key to return to the previous step.
Storing a Label into Memory
69
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE FILE MEMORY
Printing a Stored Label File
Press the File key to display the File screen.
Select "Print" using the or key.
Press the OK or Enter key.
1
2
3
The file number of a stored label is displayed.
The label text is also displayed to identify the label.
Select a file number using the
key to print the selected label. The label is printed from the machine.
or
key, and then press the Print, OK or Enter
4
• Press the Escape key to return to the previous step.
• The message "No Text!" is displayed when you try to print a file with no text.
Deleting a Stored Label File
Press the File key to display the File screen.
1
2
3
Select "Delete" using the
or
key.
Press the OK or Enter key.
The file number of a stored label is displayed.
The label text is also displayed to identify the label.
Select a file number using the
The message “Delete?” is displayed.
or
key, and then press the OK or Enter key.
4
5
Press the OK or Enter key to delete the file.
The file is deleted and the screen returns to the text entry screen.
Press the Escape key to cancel deleting the file and return to the previous screen.
Printing aDSotowrendlLoaabdel fFriolem Www.Somanuals.com. All Manuals Search And Download.
70
MAINTAINING YOUR P-TOUCH
Resetting the P-touch
You can reset the internal memory of your P-touch when you want to clear all saved
label files, or in the event the P-touch is not operating correctly.
Resetting data to factory settings (Downloaded data is not reset.)
Turn off the machine. Press and hold down the Shift and
R
keys. While holding down the
Shift and keys, press the Power key once and then release the Shift and
R
R
keys.
Resetting data to factory settings (Downloaded data is reset.)
Turn off the machine. Press and hold down the Shift and Backspace keys. While holding
down the Shift and Backspace keys, press the Power key once and then release the Shift
and Backspace keys.
• Release the Power key before releasing the other key.
• All text, format settings, option settings and stored label files are cleared when you reset the
P-touch. Language and unit settings will also be cleared
Maintenance
Your P-touch should be cleaned on a regular basis to maintain its performance and life
span.
Always remove the batteries and disconnect the AC adapter before cleaning the P-touch.
1
Cleaning the Unit
Wipe any dust and marks from the main unit using a soft, dry cloth.
Use a slightly dampened cloth on difficult to remove marks.
2
3
4
5
6
7
Do not use paint thinner, benzene, alcohol or any other organic solvent. These may deform the
case or damage the appearance of your P-touch.
8
9
Resetting the P-touch
71
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTAINING YOUR P-TOUCH
Cleaning the Print Head
Streaks or poor quality characters on printed
labels generally indicates that the print head is
dirty. Clean the print head using a cotton swab or
the optional print head cleaning cassette
(TZ-CL4).
Print head
• Do not touch the print head directly with your
bare hands.
• Refer to the instructions provided with the print
head cleaning cassette for directions on how to
use it.
Cleaning the Tape Cutter
Tape adhesive can build up on the cutter blade after
repeated use, taking the edge off the blade which may
result in the tape jamming in the cutter.
• About once every year, wipe the cutter blade
using a cotton swab moistened with Isopropyl
alcohol (rubbing alcohol).
• Do not touch the cutter blade directly with your
bare hands.
Maintenance
72
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
What to do when...
Problem
Solution
respond normally.
does not solve the problem, disconnect the AC adapter and
remove the batteries for more than 10 minutes.
The display remains
Check that the batteries are correctly installed and that the
blank after turning on AC adapter designed exclusively for your P-touch
the power.
(provided) is correctly connected.
The LCD messages
are displayed in a
foreign language.
your desired language.
The label is not
printed after pressing
the Print key.
• Check that text has been entered and that the tape
cassette is installed correctly with sufficient tape
remaining.
• If the tape is bent, cut off the bent section and thread the
tape through the tape exit slot.
• If the tape is jammed, remove the tape cassette and then
pull out the jammed tape and cut it. Check that the end of
the tape passes through the tape guide before reinstalling
the tape cassette.
The label is not
printed correctly.
• Remove the tape cassette and reinstall it, pressing it firmly
until it clicks into place.
• If the print head is dirty, clean it with a cotton swab or
optional print head cleaning cassette (TZ-CL4).
• Check that the Cut Option setting is not set to Chain or No
Cut, as the tape will not be fed after printing the label.
Alternatively, hold down the Shift key and press the
Preview key to feed and cut the tape.
1
2
3
4
5
6
7
The ink ribbon is
separated from the
ink roller.
If the ink ribbon is broken, replace the tape cassette. If not,
leave the tape uncut and remove the tape cassette, then
wind the loose ink ribbon onto the spool as shown in the
figure.
Spool
8
9
What to do when...
73
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Problem
Solution
The P-touch stops
while printing a label.
• Replace the tape cassette if striped tape is visible, as this
indicates that you have reached the end of the tape.
• Replace all batteries or connect the AC adapter directly to
the P-touch.
The label is not cut
automatically.
Check that the Cut Option setting is not set to Chain or No Cut,
as the tape will not be fed after printing the label. Alternatively,
hold down the Shift key and press the Preview key to feed
and cut the tape.
Label files saved
previously are now
empty.
All files stored in the internal memory are deleted if the
batteries are weak or the AC adapter was disconnected.
What to dDo owwhennl..o. ad from Www.Somanuals.com. All Manuals Search And Download.
74
Error Messages
When an error message appears on the display, follow the directions provided below.
Message
Cause/Remedy
Battery Weak!*
The installed batteries are getting weak.
Check
The following are likely causes.
Battery!
• The batteries are installed with the negative and positive
ends the wrong way round.
• Other types of batteries are being used with alkaline
batteries.
• Old and new batteries are being used together.
• The batteries are about to run out.
If the power does not turn off automatically, press any key to
clear the error message before turning the unit off.
Check that the correct batteries are being used, and are
installed the right way round.
Wrong Type
Of Adapter
Connected!
An incompatible AC adapter is connected. After the power is
turned off automatically, use the AC adapter designed
exclusively for your P-touch.
Cutter Error!*
The tape cutter is closed when you try to print or feed tape.
Turn the P-touch off and then on again before continuing.
When tape is tangled in the cutter, remove the tape.
No Text!*
There is no text, symbols or bar code data entered when you
try to print or preview a label. Enter data before continuing.
Insert Tape
Cassette!*
There is no tape cassette installed when you try to print or
preview a label, or feed tape. Install a tape cassette before
continuing.
1
2
3
4
5
6
7
Tape Cassette
Changed!*
The tape cassette was changed while printing, etc. Make
sure the correct tape cassette is inserted before printing.
Line Limit!
Max 7 Lines*
There are already seven lines of text when you press the
Enter key. Limit the number of lines to seven.
Tape Width
Limit!
Max 5 Lines*
There are more than five lines of text when you press the
Print or Preview key while using 18mm tape. Limit the
number of lines to five, or replace with a larger width tape
cassette.
Tape Width
Limit!
Max 3 Lines*
There are more than three lines of text when you press the
Print or Preview key while using 12 mm tape. Limit the
number of lines to three, or replace with a larger width tape
cassette.
8
9
* Press any key to clear the error message.
Download from Www.Somanuals.com. All Manuals Search And DownElorraodr M. essages
75
TROUBLESHOOTING
Message
Cause/Remedy
Tape Width
Limit!
Max 2 Lines*
There are more than two lines of text when you press the
Print or Preview key while using 9 mm or 6 mm tape. Limit
the number of lines to two, or replace with a larger width tape
cassette.
Tape Width
Limit!
Max 1 Line*
There is more than one line of text when you press the Print
or Preview key while using 3.5mm tape. Limit the number of
lines to one, or replace with a larger width tape cassette.
Block Limit!
Max 5 Blocks*
There are already five blocks of text. Limit the number of
blocks to five.
Text Full!*
The maximum number of characters have already been
entered. Edit the text and use fewer characters.
Length Limit!*
The length of the label to be printed using the text entered is
longer than 1 m. Edit the text so that the length of the label is
less than 1 m.
Insert
24mm Tape
Cassette!*
An 24mm tape cassette is not installed when an Auto-Format
for 24mm tape is selected. Install an 24mm tape cassette.
Insert
18mm Tape
Cassette!*
An 18 mm tape cassette is not installed when an Auto-
Format for 18 mm tape is selected. Install an 18 mm tape
cassette.
Insert
12mm Tape
Cassette!*
An 12 mm tape cassette is not installed when an Auto-
Format for 12 mm tape is selected. Install a 12 mm tape
cassette.
Insert
9mm Tape
Cassette!*
An 9 mm tape cassette is not installed when an Auto-Format
for 9 mm tape is selected. Install a 9 mm tape cassette.
Insert
6mm Tape
Cassette!*
An 6 mm tape cassette is not installed when an Auto-Format
for 6 mm tape is selected. Install a 6 mm tape cassette.
Insert
3.5mm Tape
Cassette!*
An 3.5mm tape cassette is not installed when an Auto-
Format for 3.5mm tape is selected. Install an 3.5mm tape
cassette.
Too Much Text
For This Layout!*
The maximum number of characters for the selected layout
have already been entered. Edit the text to use fewer
characters or use a different layout.
* Press any key to clear the error message.
Error Messages
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Message
Incorrect
Value!*
Cause/Remedy
The value entered for setting the tape length, tab length,
multiple copies or numbering function is invalid. Enter a valid
value for the setting.
Select Other
Cut Option!*
The tape length set using the tape length setting is shorter
than the total length of the left and right margins applied for
the "Large Margin" cutting option. Select a different cutting
option. option.
Text
Too Long!*
The length of the label to be printed using the text entered is
longer than the length setting. Edit the text to fit within the set
length or change the length setting.
Text
The text size is too large. Select a different size option.
Too High!*
Memory Full!*
There is not enough internal memory available when you try
to save a label file. Delete any unnecessary files to make
more memory available for the new label file.
Check # of
Digits
Entered!*
The number of digits entered in the bar code data does not
match the number of digits set in the bar code parameters.
Enter the correct number of digits.
Input A,B,C or D
At Start&End!*
The bar code data entered does not have the required start/
stop code (A, B, C, or D required at the beginning and end of
the bar code data for the CODABAR protocol). Enter the bar
code data correctly.
Maximum Of
5 Bar Codes
Per Label!*
There are already 5 bar codes entered in the text data when
you try to enter a new bar code. You can only use up to five
bar codes in each label.
1
Category Full!*
The memory available for categories is full.
To make more memory available, delete any unnecessary
registered categories by highlighting the category and
pressing the Clear key.
2
3
4
5
6
7
Installed tape is not Tape that is incompatible with the machine has been
compatible with this installed. Use compatible tape.
machine!*
* Press any key to clear the error message.
8
9
Download from Www.Somanuals.com. All Manuals Search And DownElorraodr M. essages
77
APPENDIX
Specifications
Main Unit
Item
Display
Specification
Character display
Screen contrast
Printing
16 characters x 3 lines (128 dot x 48 dot) ,Backlit
5 levels (+2, +1, 0, -1, -2)
Print method
Print head
Thermal Transfer
128 dot / 180 dpi
Print height
Print speed
Tape cassette
No. of lines
18mm max. (when using 24mm tape)
Approx. 10 mm / sec.
TZ tape cassette (3.5, 6, 9, 12, 18, 24 mm widths)
24mm tape : 1-7 lines; 18 mm tape : 1 - 5 lines;
12 mm tape : 1 - 3 lines; 9 mm tape : 1 - 2 lines;
6 mm tape : 1 - 2 lines; 3.5mm tape : 1 line
Cut and feed
Memory
Large Margin, Small Margin, Chain, No Cut, Special Tape
Memory buffer size Maximum 2800 characters
File storage
Other Features
Input method
Templates
Maximum 99 files
Text Reminder
Label Collections, Auto-Format, Block Layouts
Power Supply
Power supply
AC adapter (AD-24ES), Eight AA-size alkaline batteries
(LR6).
Auto Power-off
Battery: 5 min.*, AC adapter: 8 hours
*When using P-touch only. When connected to a PC, 1
hour.
Size
Approx.177.0mm (W) x 237.5mm (D) x 70.4mm (H)
Approx.880g (without tape cassette and batteries)
Dimensions
Weight
Other
Operating
temperature /
humidity
50 ~ 95°F / 20 ~ 80% humidity (without condensation)
Maximum wet bulb temperature: 80.6°F
Specifications
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|