Black Box Network Hardware LWE100A User Manual
LWE100A  
LWE100A-W1  
LWE100A-W2  
LWE100A-KIT-W1  
LWE100A-KIT-W2  
LWE100A-KIT  
LWE100AE  
LWE100AE-KIT  
Wireless P-T-P Ethernet Extender User Manual  
Extend Ethernet links between buildings wirelessly  
and with ease.  
Provides affordable point-to-point wireless Ethernet extension up to  
6.2 miles (10 km).  
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)  
FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746  
Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018  
Web site: www.blackbox.com • E-mail: [email protected]  
Customer  
Support  
Information  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FCC and IC RFI Statements  
FEDERAL COMMUNICATIONS COMMISSION  
and INDUSTRY CANADA  
RADIO FREQUENCY INTERFERENCE STATEMENTS  
Class B Digital Device. This equipment has been tested and found to comply with the limits for a Class B computing device  
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a  
residential installation. However, there is no guarantee that interference will not occur in a particular installation. This equipment  
generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may  
cause harmful interference to radio communications. If this equipment does cause harmful interference to radio or telephone  
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the  
interference by one of the following measures:  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the equipment and receiver.  
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
• Consult an experienced radio/TV technician for help.  
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s  
authority to operate the equipment.  
To meet FCC requirements, shielded cables and power cords are required to connect this device to a personal computer or other  
Class B certified device.  
This digital apparatus does not exceed the Class B limits for radio noise emission from digital apparatus set out in the Radio  
Interference Regulation of Industry Canada.  
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de  
classe B prescrites dans le Règlement sur le brouillage radioélectrique publié par Industrie Canada.  
724-746-5500 | blackbox.com  
Page 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOM Statement  
Instrucciones de Seguridad  
(Normas Oficiales Mexicanas Electrical Safety Statement)  
1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el aparato eléctrico sea operado.  
2. Las instrucciones de seguridad y operación deberán ser guardadas para referencia futura.  
3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de operación deben ser respetadas.  
4. Todas las instrucciones de operación y uso deben ser seguidas.  
5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca de la tina de baño, lavabo, sótano mojado o cerca  
de una alberca, etc.  
6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que sean recomendados por el fabricante.  
7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea recomendado por el fabricante.  
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá a lo descrito en las instrucciones de operación.  
Todo otro servicio deberá ser referido a personal de servicio calificado.  
9. El aparato eléctrico debe ser situado de tal manera que su posición no interfiera su uso. La colocación del aparato eléctrico  
sobre una cama, sofá, alfombra o superficie similar puede bloquea la ventilación, no se debe colocar en libreros o gabinetes  
que impidan el flujo de aire por los orificios de ventilación.  
10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor como radiadores, registros de calor, estufas u otros  
aparatos (incluyendo amplificadores) que producen calor.  
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del tipo descrito en el instructivo de operación, o como  
se indique en el aparato.  
12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización del equipo no sea eliminada.  
13. Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni pellizcados por objetos colocados  
sobre o contra ellos, poniendo particular atención a los contactos y receptáculos donde salen del aparato.  
14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las recomendaciones del fabricante.  
15. En caso de existir, una antena externa deberá ser localizada lejos de las lineas de energia.  
16. El cable de corriente deberá ser desconectado del cuando el equipo no sea usado por un largo periodo de tiempo.  
17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre la cubierta u orificios de ventilación.  
18. Servicio por personal calificado deberá ser provisto cuando:  
A: El cable de poder o el contacto ha sido dañado; u  
B: Objectos han caído o líquido ha sido derramado dentro del aparato; o  
C: El aparato ha sido expuesto a la lluvia; o  
D: El aparato parece no operar normalmente o muestra un cambio en su desempeño; o  
E: El aparato ha sido tirado o su cubierta ha sido dañada.  
724-746-5500 | blackbox.com  
Page 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
Table of Contents  
1. Specifications.........................................................................................................................................................................7  
1.1 General..........................................................................................................................................................................7  
1.2 Radio.............................................................................................................................................................................7  
1.3 Software........................................................................................................................................................................7  
2. Overview...............................................................................................................................................................................8  
2.1 Introduction...................................................................................................................................................................8  
2.2 Features.........................................................................................................................................................................8  
2.3 What’s Included ............................................................................................................................................................8  
2.4 Hardware Description....................................................................................................................................................8  
2.5 Typical Application.......................................................................................................................................................10  
3. Hardware Installation ......................................................................................................................................................... 11  
3.1 Preparing for Installation.............................................................................................................................................. 11  
3.2 Professional Installation Required................................................................................................................................. 11  
3.3 Safety Precautions....................................................................................................................................................... 11  
3.4 Installation Precautions................................................................................................................................................ 11  
3.5 Hardware Installation Steps ......................................................................................................................................... 11  
3.5.1 Connect.............................................................................................................................................................. 11  
3.5.2 Pole Mounting ...................................................................................................................................................14  
3.5.3 Using the External Antenna................................................................................................................................16  
3.5.4 Using the Grounding Wire ................................................................................................................................. 17  
4. Basic Settings .....................................................................................................................................................................19  
4.1 Factory Default Settings...............................................................................................................................................19  
4.2 System Requirements ..................................................................................................................................................20  
4.3 Logging in to the Web-based Interface.......................................................................................................................20  
4.4 Basic System Settings ..................................................................................................................................................21  
4.5 Time Settings...............................................................................................................................................................24  
4.6 RADIUS Settings..........................................................................................................................................................24  
4.7 Firewall Settings...........................................................................................................................................................25  
4.8 Basic Wireless Settings.................................................................................................................................................29  
4.9 Site Survey...................................................................................................................................................................31  
4.10 VAP Profile Settings....................................................................................................................................................31  
4.11 VLAN Tab ...................................................................................................................................................................33  
5. Advanced Settings..............................................................................................................................................................34  
5.1 Advanced Wireless Settings.........................................................................................................................................34  
5.2 Wireless Security Settings............................................................................................................................................35  
5.2.1 Data Encyrption and Authentication Settings.....................................................................................................35  
5.2.2 Access Control ...................................................................................................................................................37  
5.2.3 WDS Settings .....................................................................................................................................................38  
6. Management......................................................................................................................................................................39  
6.1 Remote Management..................................................................................................................................................39  
6.2 SNMP Management....................................................................................................................................................39  
6.3 Coovachilli Settings......................................................................................................................................................41  
6.4 Upgrade Firmware.......................................................................................................................................................42  
6.5 Backup/Retrieve Settings.............................................................................................................................................42  
6.6 Restore Factory Default Settings..................................................................................................................................43  
6.7 Reboot.........................................................................................................................................................................44  
724-746-5500 | blackbox.com  
Page 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
6.8 Password.....................................................................................................................................................................44  
6.9 Certificate Settings ......................................................................................................................................................45  
7. Monitoring Tools.............................................................................................................................................................. 46  
7.1 System Log................................................................................................................................................................ 46  
7.2 Site Survey................................................................................................................................................................. 46  
7.3 Ping Watchdog.......................................................................................................................................................... 47  
7.4 Data Rate Test ........................................................................................................................................................... 48  
7.5 Antenna Alignment................................................................................................................................................... 48  
7.6 Speed Test................................................................................................................................................................. 49  
8. Status .......................................................................................................................................................................... 50  
8.1 View Basic Information.............................................................................................................................................. 50  
8.2 View Association List................................................................................................................................................. 50  
8.3 View Network Flow Statistics .....................................................................................................................................51  
8.4 View ARP Table ......................................................................................................................................................... 52  
8.5 View Bridge Table...................................................................................................................................................... 52  
8.6 View Active DHCP Client Table.................................................................................................................................. 52  
8.7 View Network Activities ............................................................................................................................................ 53  
9. Troubleshooting ............................................................................................................................................................... 54  
9.1 Frequently Asked Questions...................................................................................................................................... 54  
9.2 Contacting Black Box................................................................................................................................................. 55  
9.3 Shipping and Packaging ............................................................................................................................................ 55  
Appendix A. ASCII .................................................................................................................................................................. 56  
Appendix B. SSH Settings........................................................................................................................................................ 57  
724-746-5500 | blackbox.com  
Page 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 1: Specifications  
1. Specifications  
1.1 General  
Standards — IEEE 802.3u MDI/MDI-X 10/100 Fast Ethernet, IEEE 80.11b/g wireless LAN interface, IEEE 802.1n draft wireless LAN  
standard  
Temperature Tolerance — Operating: -4 to +158° F (-20 to +70° C);  
Storage: -22 to +176° F (-30 to +80° C)  
Humidity Tolerance — Operating: 10–95%;  
Storage: 10–95%  
Power — Input current: 0.5 A maximum;  
Output Voltage: 15 V;  
Output Current: 0.8 A  
Size — 2.4"H x 2.5"W x 8.9"D (6.1 x 6.4 x 22.8 cm)  
Weight — < 1.1 lb. (< 0.5 kg)  
1.2 Radio  
Antenna — Default embedded 8-dBi directional antenna (Vertical-Pol), reserve N-type connector (plug), software switchable  
Modulation — IEEE 802.11b (DSSS): CCK, DQPSK, DBPSK;  
IEEE 802.11g/n (OFDM/DSSS): QAM-16, QPSK, BPSK  
Operating Frequency — IEEE 802.11b/g ISM Band; 802.11g/n 20 MHz;  
U.S., Canada: 2.412 GHz–2.462 GHz;  
EU: 2.412 GHz–2.472 GHz;  
IEEE 802.11gn 40 MHz Band;  
U.S., Canada: 2.422 GHz–2.452 GHz;  
EU: 2.422 GHz–2.462 GHz  
Output Power* — IEEE 802.11b: 27.5 dBm @ 11 Mbps;  
IEEE 802.11g: 27.5 dBm @ 6 Mbps;  
IEEE 802.11gn: 27.5 dBm @ HT20, 27.5 dBm @ HT40  
*Band edge exclusive (controllable for different country regulations)  
Sensitivity — IEEE 802.11b: -88 dBm @ 11 Mbps;  
IEEE 802.11g: -73 dBm @ 6 Mbps;  
IEEE 802.11n: -70 dBm @ HT20, -67 dBm @ HT40  
1.3 Software  
Advance Settings — Radio on/off, WMM/Regatta mode, output power control, fragmentation length, beacon interval, RTS/CTS  
threshold, DTIM interval  
Management — Telnet, FTP, SMP, password changes, firmware updates, configuration files  
Operation Mode — CPE, AP  
Security — WEP 64, 128.152-bit, WPA/WPA2, WPA-PSK/WPA2-PSK, 802.1x authentication  
724-746-5500 | blackbox.com  
Page 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 2: Overview  
2. Overview  
2.1 Introduction  
Designed for outdoor environment applications, the Wireless P-T-P Ethernet Extender is a high-performance last-mile broadband  
solution that provides reliable wireless network coverage. As an IEEE 802.11b/g compliant wireless device, the Wireless P-T-P  
Ethernet Extender is able to provide stable and efficient wireless performance. The extender delivers a much faster data rate than  
normal wireless devices and higher bandwidth with longer range for outdoor applications.  
The Wireless P-T-P Ethernet Extender supports four wireless communication connectivity device types (AP, Wireless Client, Bridge  
and AP Repeater), allowing for various application requirements.  
High output power and reliable performance make the Wireless P-T-P Ethernet Extender an ideal wireless broadband solution for  
wireless Internet service providers and system integrators.  
2.2 Features  
• Complies with IEEE 802.11b/g and IEEE 802.11n standards.  
• Supports passive PoE, supplied with 12V.  
• Highly reliable watertight housing endures almost any harsh environment.  
• Four operating modes include AP, Wireless Client, WDS, and AP Repeater.  
• Supports 64/128/152-bit WEP and 802.1X, WPA, WPA2, WPA & WPA2, WPA-PSK, WPA2-PSK, and WPA-PSK & WPA2-PSK.  
• Includes a user-friendly Web and SNMP-based management interface.  
2.3 What’s Included  
Your package should contain the following items. If anything is missing or damaged, contact Black Box Technical Support  
at 724-746-5500 or [email protected].  
LWE100A or LWE100AE  
• Wireless P-T-P Ethernet Extender  
• Pole-mounting ring  
• Power cord and PoE injector  
• A printed Quick Installation Guide.  
NOTE: You can download this user manual in PDF format from  
ftp://ftp.blackbox.com/anonymous/manuals/L/LWE100A_rev1_user.pdf  
LWE100A-KIT or LWE100AE-KIT  
• (2) Wireless P-T-P Extenders, preconfigured for bridging operation  
• (2) pole-mounting rings  
• (2) power cords and PoE injectors  
• A printed Quick Installation Guide.  
NOTE: The LWE100A-KIT and LWE100AE-KIT will be ready to deploy in bridging operation. Just plug them in with line-of-sight,  
and your connection will be established.  
2.4 Hardware Description  
Figure 2-1 shows the LWE100A. Figure 2-2 illustrates the pole mounting ring and Figure 2-3 shows the power cord and PoE  
injector. Table 2-1 describes these components.  
724-746-5500 | blackbox.com  
Page 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 2: Overview  
1
2
2
2
Figure 2-1. LWE100A Ethernet extender.  
3
Figure 2-2. Pole-mounting ring.  
4
5
6
Figure 2-3. Power cord and PoE injector.  
724-746-5500 | blackbox.com  
Page 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 2: Overview  
Table 2-1. Components.  
Number  
Component  
Description  
1
(1) reverse N-type connector  
Ground the connector first, then install the antenna here.  
2
3
4
5
(3) pole mounts  
You will install the pole mounting ring through these mounts.  
Secures the extender to the pole  
(1) pole mounting ring  
(1) U.S. power plug  
Connects to a power source  
(1) 2.5-mm barrel connector  
Connects to the PoE injector  
6
(1) Power over Ethernet (PoE) injector Supplies power to the extender  
WARNING: Users MUST use the power cord and PoE injector shipped in the box with the Wireless P-T-P Ethernet Extender.  
Using other options will damage the extender.  
2.5 Typical Application  
This section describes the typical applications of the Wireless P-T-P Ethernet Extender. By default, it is set to AP mode. This enables  
it to establish wireless coverage; plus, it is also able to join any available wireless network under wireless client mode. The Wireless  
P-T-P Ethernet Extender is able to deliver stable and efficient broadband connectivity for various applications.  
Figure 2-4. Wireless P-T-P Ethernet Extender application.  
The Wireless P-T-P Ethernet Extender can also be used in the following environments:  
• Cost-effectively provide long distance backhaul for remote areas (for example, a village, oil well, island, mountain, etc.).  
• Establish local backhaul for campus, farm, and factory.  
• Provides access for video streaming or surveillance for industrial and mining enterprises.  
724-746-5500 | blackbox.com  
Page 10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 3: Hardware Installation  
3. Hardware Installation  
This chapter describes safety precautions and product information you have to know and check before installing the Wireless  
P-T-P Ethernet Extender.  
3.1 Preparing for Installation  
Read this chapter before installing the extender. It describes safety precautions and needed product information.  
3.2 Professional Installation Required  
Use a professional installer who is well trained in the RF installation and knowledgeable about local regulations.  
3.3 Safety Precautions  
To keep you safe and to install the hardware properly, read and follow these safety precautions.  
1. If you are installing the Wireless P-T-P Ethernet Extender for the first time, for your safety as well as others’, use a professional  
installer who is trained on the safety hazards involved.  
2. Keep safety as well as performance in mind when selecting your installation site, especially where there are electric power and  
phone lines.  
3. When installing the Wireless P-T-P Ethernet Extender, note the following things:  
NOTES:  
Do not use a metal ladder;  
Do not work on a wet or windy day;  
Wear shoes with rubber soles and heels, rubber gloves, and a long-sleeved shirt or jacket.  
4. When the system is operating, avoid standing directly in front of it. Strong RF fields are present when the transmitter is on.  
3.4 Installation Precautions  
Read and follow these installation precautions.  
WARNING: EMD (Lightning) DAMAGE IS NOT COVERED UNDER WARRANTY.  
1. Users MUST use a proper and well-installed grounding and surge arrestor with the Wireless P-T-P Ethernet Extender, otherwise,  
a random lightning could easily cause fatal damage to Wireless P-T-P Ethernet Extender.  
2. Users MUST use the power cord and PoE injector shipped in the box with the Wireless P-T-P Ethernet Extender. Using other  
components will cause damage to the extender.  
3. Users MUST power off the Wireless P-T-P Ethernet Extender first before connecting the external antenna to it. Do not switch  
from the built-in antenna to the external antenna via Web management without physically attaching the external antenna onto  
the Wireless P-T-P Ethernet Extender, otherwise, the extender might be damaged.  
3.5 Hardware Installation Steps  
3.5.1 Connect  
1. On the bottom of the Wireless P-T-P Ethernet Extender is a movable cover. Grab the cover and pull it back gently to remove it  
as shown in Figure 3-1.  
724-746-5500 | blackbox.com  
Page 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 3: Hardware Installation  
Figure 3-1. Removing the bottom cover.  
2. Plug a standard Ethernet cable into the RJ-45 port. See Figure 3-2.  
Figure 3-2. Plugging in the cable.  
3. Slide the cover back to seal the bottom of the Wireless P-T-P Ethernet Extender.  
724-746-5500 | blackbox.com  
Page 12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 3: Hardware Installation  
Figure 3-3. Replacing the cover.  
4. Take out the power cord and PoE injector, and plug the power cord into the DC port of the PoE injector as the right-side  
picture in Figure 3-4 shows.  
Figure 3-4. Installing the power cord and PoE injector.  
5. Put what you assembled in step 3 and step 4 together by plugging the other side of the Ethernet cable from step 3 into the  
PoE port of the PoE injector shown in step 4. When you finish step 5, the extender, power cord, and PoE injector will appear as  
shown in Figure 3-5.  
724-746-5500 | blackbox.com  
Page 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 3: Hardware Installation  
Figure 3-5. Extender.  
3.5.2 Pole Mounting  
1. Turn the Wireless P-T-P Ethernet Extender over. Put the pole mounting ring through the middle hole of the Wireless P-T-P  
Ethernet Extender.  
NOTE: Use a screwdriver to unlock the pole-mounting ring before putting it through the Wireless P-T-P Ethernet Extender as the  
right-side picture in Figure 3-6 shows.  
724-746-5500 | blackbox.com  
Page 14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 3: Hardware Installation  
Figure 3-6. Unlocking the pole-mounting ring.  
2. Mount the Wireless P-T-P Ethernet Extender firmly to the pole by locking the pole mounting ring tightly.  
Figure 3-7. Mounting the extender to a pole.  
3. When installation is complete, the extender should look like Figure 3-8.  
724-746-5500 | blackbox.com  
Page 15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 3: Hardware Installation  
Figure 3-8. Extender installed outdoors on a pole.  
3.5.3 Using the External Antenna  
If you prefer to use the external antenna with N-type connector for your application instead of the built-in directional antenna,  
follow the steps below.  
1. Grab the black rubber on the top of the Wireless P-T-P Ethernet Extender, and slightly pull it up as shown in Figure 3-9. The  
metal N-type connector will appear.  
724-746-5500 | blackbox.com  
Page 16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 3: Hardware Installation  
Figure 3-9. Installing the external antenna.  
2. Connect your antenna with the N-type connector on the top of the Wireless P-T-P Ethernet Extender.  
NOTES:  
1. Before connecting the external antenna with the N-type connector to the Wireless P-T-P Ethernet Extender, users should  
prepare the cable in advance, if needed.  
2. While connecting the N-type connectors, users should be careful not to damage the connectors.  
WARNING: Users MUST power off the Wireless P-T-P Ethernet Extender first before connecting the external antenna to it. Do not  
switch from the built-in antenna to the external antenna from Web management without physically attaching the  
external antenna onto the Wireless P-T-P Ethernet Extender. Otherwise, the Wireless P-T-P Ethernet Extender might be  
damaged.  
3.5.4 Using the Grounding Wire  
The Wireless P-T-P Ethernet Extender is shipped with a grounding wire. Properly ground the unit to protect against power surges.  
1. Loosen and remove the metal O-ring on the N-type antenna connector.  
2. Put the grounding wire into the connector and tighten it with the O-ring.  
Figure 3-10. Connecting one end of the grounding wire.  
724-746-5500 | blackbox.com  
Page 17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 3: Hardware Installation  
3. Connect the other end of the grounding wire to the earth ground.  
Figure 3-11. Connecting the other end of the grounding wire.  
724-746-5500 | blackbox.com  
Page 18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 4: Basic Settings  
4. Basic Settings  
4.1 Factory Default Settings  
To return the extender to its factory-default settings, see Section 6.6.  
Table 4-1. Wireless P-T-P Ethernet Extender Factory Default Settings.  
Parameter  
Default Setting  
Username  
admin  
Password  
password  
Wireless Device Name  
Operating Mode  
Data Rate  
apXXXXXX (X represents the last 6 digits of the Ethernet MAC address)  
AP  
Auto  
LAN IP Address  
LAN Subnet Mask  
LAN Gateway  
192.168.1.1  
255.255.255.0  
0.0.0.0  
0.0.0.0  
0.0.0.0  
Enable  
802.11b/g/n  
6
LAN Primary DNS Server  
LAN Secondary DNS Server  
Spanning Tree  
802.11 Mode  
Channel Number  
SSID  
Wireless  
Enable  
Disable  
Auto  
Broadcast SSID  
HT Protect  
Data Rate  
Output Power  
Full  
Channel Mode  
20 MHz  
Enabled  
2346  
WMM  
RTS Threshold (byte)  
Fragmentation Length (byte)  
Beacon Interval  
DTIM Interval  
2346  
100  
1
Space in Meters  
Flow Control by AP  
Security  
0
Disable  
Open System  
None  
Encryption  
Wireless Separation  
Access Control  
Disable  
Disable  
Enable  
Public  
SNMP Enable/Disable  
SNMP Read Community Name  
SNMP Write Community Name  
SNMP IP Address  
Private  
0.0.0.0  
724-746-5500 | blackbox.com  
Page 19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 4: Basic Settings  
4.2 System Requirements  
Before configuration, make sure your system meets the following requirements:  
• You will need a computer coupled with a 10/100 BASE-TX adapter;  
• Configure the computer with a static IP address of 192.168.1.x.  
NOTE: The default IP address of Wireless P-T-P Ethernet Extender is 192.168.1.1. (X cannot be 0, 1, nor 255);  
• A Web browser on a PC for configuration such as Microsoft® Internet Explorer® 6.0 or above, Netscape®, Firefox®, or Google  
Chrome®.  
4.3 Logging Into the Web-based Interface  
The Wireless P-T-P Ethernet Extender provides you with a user-friendly Web-based management tool.  
Open a Web browser and enter the IP address (Default: 192.168.1.1) of the Wireless P-T-P Ethernet Extender into the address field.  
You will see the login page (Figure 4-1).  
Figure 4-1. Login page.  
Enter the username (Default: admin) and password (Default: password) respectively and click “Login” to login to the main page  
of the Wireless P-T-P Ethernet Extender. This management interface provides five main options in the black bar, including Status,  
System, Wireless, Management, and Tools. See Figure 4-2.  
724-746-5500 | blackbox.com  
Page 20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 4: Basic Settings  
Figure 4-2. Main page.  
NOTE: The username and password are case-sensitive, and the password should be no more than 19 characters.  
4.4 Basic System Settings  
If you are using the Wireless P-T-P Ethernet Extender for the first time, we recommend starting configuration from “Basic  
Settings” in the “System” screen shown next.  
Figure 4-3. Basic system settings.  
724-746-5500 | blackbox.com  
Page 21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 4: Basic Settings  
Basic Settings  
• Device Name: Specify the device name, which is composed of no more than 15 characters with (0-9), (A-Z), (a-z), or (-).  
• Network Mode: Specify the network mode, including Bridge and Router. It is easy to configure parameters in Bridge Mode;  
however, users must pay extra attention to the way they configure the device when it is set to Router Mode. For details, please  
refer to “TCP/IP Settings” below.  
• Ethernet Data Rate: Specify the transmission rate of data for Ethernet. The default is “Auto.”  
• Country Region: Available specific channels and/or operational frequency bands depend on the country where the extender is  
used.  
• Spanning Tree: Spanning Tree Protocol (STP) is a link management protocol for AP that provides path redundancy while  
preventing loops in a network. STP allows only one active path at a time between the access points, but establishes the  
redundant link as a backup if the initial link fails.  
• STP Forward Delay: STP Forward Delay is the time spent in detecting and learning network tree topology state before entering  
the forward state. The default time value is 1 sec.  
• GPS Coordinate Settings: The GPS Coordinate Setting marks the latitude and longitude of the extender. Enter the coordinates  
and click the “Apply” button.  
TCP/IP Settings  
Open “TCP/IP Settings” in “System” as shown in Figure 4-4 to configure the parameters for the LAN that connects to the  
extender’s LAN port. In this page, users may change the settings for IP Address, Subnet Mask, and DHCP Server.  
Figure 4-4. TCP/IP settings (Bridge).  
Obtain IP Address Automatically: If a DHCP server exists in your network, you can check this option. This enables the Wireless  
P-T-P Ethernet Extender to obtain IP settings automatically from that DHCP server.  
724-746-5500 | blackbox.com  
Page 22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 4: Basic Settings  
NOTES:  
1. When the IP address of the extender is changed, the clients on the network often need to wait for a while or even reboot  
before they can access the new IP address. For immediate access to the bridge, flush the netbios cache on the client computer  
by running the “nbtstat –r” command before using the device name of the CPE to access its Web management page.  
2. If the IEEE 802.11b/g/n Wireless Outdoor CPE is unable to obtain an IP address from a valid DHCP server, it will fall back to  
default static IP address.  
Use Fixed IP Address: Check this option. You have to specify a static IP address, subnet mask, default gateway, and DNS server for  
the extender manually. Make sure the specified IP address is unique on your network to prevent IP conflict.  
If the IEEE 802.11b/g/n Wireless Outdoor CPE is configured in Router mode, you need to configure some additional TCP/IP  
parameters for accessing the Internet.  
Figure 4-5. TCP/IP settings (Router).  
WAN Settings: Specify the Internet access method to Static IP, DHCP, or PPPOE. Users must enter WAN IP Address, Subnet Mask,  
and Gateway settings provided by your ISPs.  
LAN Settings: When DHCP Server is disabled, users can specify the IP address and the subnet mask for the extender manually.  
Make sure the specified IP address is unique on your network to prevent IP conflict. When DHCP Server is enabled, users may  
specify DHCP IP Address Range, DHCP Subnet Mask, DHCP Gateway, and Lease Time (15-44640 minutes). DHCP relay agents  
forward DHCP requests and replies between clients and servers when they are not on the same physical subnet. To enable the  
DHCP relay agent, check the “Enable DHCP Relay” checkbox and enter the IP address of the DHCP server.  
WARNING:  
In AP mode, the Wireless P-T-P Ethernet Extender must establish a connection with another wireless device before it is set to  
Router mode. To access the unit in Router mode via a wired port, type the WAN IP address you will use to enter the Web page.  
The WAN is on a wired port and the LAN is on a wireless port. Or, you can access the device through the wireless device  
connected with the extender.  
In wireless client mode, users can access the extender via its wired port. The WAN is on a wireless port and the LAN is on a wired  
port when the device is set to Router mode.  
724-746-5500 | blackbox.com  
Page 23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 4: Basic Settings  
WARNING: Bridge mode and AP Repeater mode are similar to AP mode when the device is set to Router mode; the WAN is on  
wired port and the LAN is on wireless port. Users must also connect the extender with another wireless device before  
it is set to Router mode and access the extender via the connected wireless device.  
4.5 Time Settings  
Compliant with NTP, the Wireless P-T-P Ethernet Extender keeps time to match the Internet time. Configure the time in “Time  
Settings” from “System.” To use this feature, check “Enable NTP Client Update” in advance.  
Figure 4-6. Time settings.  
Current Time: Display the present time in Yr, Mon, Day, Hr, Min, and Sec.  
Time Zone Select: Select the time zone from the dropdown list.  
NTP Server: Select the time server from the “NTP Server” dropdown list or manually input the IP address of an available time  
server into “Manual IP.” Click on “Apply” to save the settings.  
4.6 RADIUS Settings  
RADIUS (Remote Authentication Dial-In User Service) is a server for remote user authentication and accounting; it plays a central  
role in the network because it provides authenticating, authorizing, accounting, auditing, alarming, etc. It enables an organization  
to maintain user profiles in a central database that all remote servers can share.  
Open “RADIUS Settings” in “System” to make RADIUS configuration.  
724-746-5500 | blackbox.com  
Page 24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 4: Basic Settings  
Figure 4-7. RADIUS settings.  
Authenticating RADIUS Server  
This is for RADIUS authentication. It can communicate with RADIUS through IP Address, Port, and Shared Secret.  
IP Address: Enter the IP address of the Radius Server;  
Port: Enter the port number of the Radius Server;  
Shared Secret: This secret word or number (or a combination of letters and numbers), which is composed of no more than 31  
characters, is shared by the Wireless P-T-P Ethernet Extender and RADIUS during authentication.  
Global-Key Update: Check this option and specify the time interval between two global-key updates.  
4.7 Firewall Settings  
The firewall is a system or group of systems that enforce an access control policy between two networks. It may also be defined  
as a mechanism used to protect a trusted network from an un-trusted network. The Wireless P-T-P Ethernet Extender can provide  
Source IP Filtering, Destination IP Filtering, Source Port Filtering, Destination Port Filtering, Port Forwarding, as well as DMZ. This is  
available only under Router Mode.  
Source IP Filtering: Source IP filtering gives users the ability to restrict certain types of data packets from your local network to  
Internet through the Wireless P-T-P Ethernet Extender. Use these filters to help secure or restrict your local network.  
724-746-5500 | blackbox.com  
Page 25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 4: Basic Settings  
Figure 4-8. Source IP filtering.  
Destination IP Filtering: Destination IP filtering gives you the ability to restrict the computers in a LAN from accessing certain  
Websites in a WAN according to specified IP addresses. Check the “Enable Source IP Filtering” checkbox and enter the IP address  
of the clients you want to restrict. Click on the “Apply” button to make the setting take effect.  
Figure 4-9. Destination IP filtering.  
724-746-5500 | blackbox.com  
Page 26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 4: Basic Settings  
Source Port Filtering: Source port filtering enables you to restrict certain ports of data packets from your local network to the  
Internet through the Wireless P-T-P Ethernet Extender. Use these filters to help secure or restrict your local network.  
Figure 4-10. Source port filtering.  
Destination Port Filtering: The destination port filtering enables you to restrict certain ports of data packets from your local  
network to the Internet through the Wireless P-T-P Ethernet Extender. Use these filters to help secure or restrict your local  
network.  
Figure 4-11. Port forwarding.  
724-746-5500 | blackbox.com  
Page 27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 4: Basic Settings  
Port Forwarding: The port forwarding allows you to automatically redirect common network services to a specific machine behind  
the NAT firewall. These settings are only necessary if you want to host a Web server or mail server on the private local network  
behind Wireless P-T-P Ethernet Extender’s NAT firewall.  
Figure 4-12. Port forwarding.  
DMZ: A Demilitarized Zone is used to provide Internet services without sacrificing unauthorized access to its local private network.  
Typically, the DMZ host contains devices accessible to the Internet traffic, such as Web (HTTP) servers, FTP servers, SMTP (e-mail)  
servers, and DNS servers.  
Figure 4-13. DMZ.  
724-746-5500 | blackbox.com  
Page 28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 4: Basic Settings  
4.8 Basic Wireless Settings  
Open “Basic Settings” in “Wireless” to configure basic wireless.  
Figure 4-14. Basic wireless settings.  
Disable Wireless LAN Interface  
Check this option to disable the WLAN interface. The wireless module of the Wireless P-T-P Ethernet Extender will then stop  
working and no wireless device can connect to it.  
Wireless Mode  
Four operating modes are available in the Wireless P-T-P Ethernet Extender.  
AP: The Wireless P-T-P Ethernet Extender establishes a wireless coverage and receives connectivity from other wireless devices.  
Wireless Client: The Wireless P-T-P Ethernet Extender can connect to the AP and join the wireless network around it.  
Bridge: The Wireless P-T-P Ethernet Extender establishes wireless connectivity with other APs by keying in a remote MAC address.  
Refer to the “WDS Setting” in Section 5.2.3 for detailed configuration.  
AP Repeater: The Wireless P-T-P Ethernet Extender servers as AP and Bridge concurrently. In other words, the extender can  
provide connectivity services for extenders in Bridge mode.  
Wireless Network Name (SSID)  
This wireless network name is shared among all associated devices in your wireless network. Keep it identical on all those devices.  
NOTE: SSID is case-sensitive and cannot exceed 32 characters.  
Broadcast SSID  
In AP mode, you need to hide the network name when you are in a wireless environment that may have potential risk. By  
disabling broadcast SSID, the STA cannot scan and find the Wireless P-T-P Ethernet Extender, so that malicious attack by some  
illegal STA can be avoided.  
724-746-5500 | blackbox.com  
Page 29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 4: Basic Settings  
802.11 Mode  
The Wireless P-T-P Ethernet Extender can communicate with wireless devices that conform to 802.11b/g or 802.11b/g/n.  
HT Protect  
Enable HT (High Throughput) protect to ensure HT transmission with MAC mechanism. Under 802.11n mode, the wireless client  
can be divided into HT STA and Non-HT STA. The one with HT protect enabled gets higher throughput.  
Frequency/Channel  
Channel varies because the available band differs from country to country. Select a proper operating channel in the drop-down  
list according to your situation.  
Extension Channel  
This channel only applies to AP, AP Repeater, and 40MHz channel width. Using channel bonding, it enables the Wireless P-T-P  
Ethernet Extender to use two channels at once. Two options are available: Upper Channel and Lower Channel.  
Channel Mode  
Four levels are available: 5MHz, 10MHz, 20MHz and 40MHz. The last one can enhance data throughput, but it takes more  
bandwidth, so it might cause potential interference.  
Antenna  
By default, the Wireless P-T-P Ethernet Extender uses its built-in antenna for directional transmission; however, if you prefer to use  
an external antenna for your application, you can switch from “Internal (8 dBi)” to ”External (N-Type).”  
When External (N-Type) is selected, an Antenna Gain bar will appear to allow you to specify the gain of the external antenna. The  
antenna gain calculates the TX power back off needed to remain in compliance with regulations.  
CAUTION: You are able to choose “External (N-Type)” only when you have installed the external antenna; otherwise, the Wireless  
P-T-P Ethernet Extender might be damaged.  
NOTES:  
The maximum output power will vary depending on the country selected to comply with the local regulation.  
The output power here is counted from the RF single chain only, not including the 8-dBi internal antenna.  
Maximum Output Power (per chain)  
Specify the signal transmission power. The higher the output power is, the wider the area the signal can cover, but the power  
consumption will be greater accordingly.  
Data Rate  
Usually “Auto” is preferred. Under this rate, the Wireless P-T-P Ethernet Extender will automatically select the highest available rate  
to transmit. In some cases, however, when there is no great demand for speed, you can have a relatively low transmit rate to  
enable a longer distance.  
Extension Channel Protection Mode  
This is to avoid conflict with other wireless networks and boost the ability of your device to catch all 802.11g transmissions.  
However, it may decrease wireless network performance. Compared to CTS-Self, the transmission amount of CTS-RTS is much  
lower.  
Enable MAC Clone  
Available only under the wireless client mode, it hides the MAC address of the AP while displaying the one of an associated wire-  
less client or the MAC address designated manually.  
724-746-5500 | blackbox.com  
Page 30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 4: Basic Settings  
4.9 Site Survey  
Under wireless client mode, the Wireless P-T-P Ethernet Extender is able to perform a site survey. It detects available information  
about the access points.  
Open “Basic Settings” in “Wireless,” by clicking the “Site Survey” button beside the “Wireless Mode” option. The wireless site  
survey window will pop up with a list of available APs in the vicinity. Select the AP you want to connect to and click “Selected” to  
establish connection.  
Figure 4-15. Site Survey.  
4.10 VAP Profile Settings  
Available in AP mode, the Wireless P-T-P Ethernet Extender allows up to 16 virtual SSIDs on a single BSSID and to configure  
different profile settings such as security and VLAN ID to each SSID. To create a virtual AP, check the “Enable” box of the profile  
and click on the profile (for example, Profile 2) to configure wireless and security settings. Click on the “Apply” button to activate  
the profile.  
724-746-5500 | blackbox.com  
Page 31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 4: Basic Settings  
Figure 4-16. VAP Profile settings.  
Figure 4-17. VAP Profile1 settings.  
Basic Settings  
Profile Name: Name of the VAP profile.  
Wireless Network Name: Enter the virtual SSID for the VAP.  
Broadcast SSID: In AP mode, you need to hide the network name when you are in a wireless environment that may have  
potential risk. By disabling broadcast SSID, the STA cannot scan and find the Wireless P-T-P Ethernet Extender, so malicious attack  
by an illegal STA can be avoided.  
724-746-5500 | blackbox.com  
Page 32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 4: Basic Settings  
Wireless Separation: Wireless separation enhances the security of network transmission. Under the mode (except wireless client  
mode), enable “Wireless Separation” to prevent the communication among associated wireless clients.  
WMM Support: WMM (Wi-Fi Multimedia) is a subset of 802.11e. It allows wireless communication to define a priority limit on the  
basis of data type under AP mode only, so time-sensitive data, such as video/audio data, may own a higher priority than common  
data. To enable WMM, the wireless client should also support it.  
Max. Station Number: By checking the “Max. Station Num,” the extender will only allow up to 32 wireless clients to associate  
with it for better bandwidth for each client. By disabling the checkbox, the extender will allow up to 128 clients to connect, but it  
is likely to cause network congestion or poor performance.  
Security Setting  
To prevent unauthorized radios from accessing data transmitting over the connectivity, the IEEE 802.11a/n Wireless Outdoor CPE  
provides you with rock solid security settings. For detailed information, go to Section 5.2, Wireless Security Settings.  
4.11 VLAN Tab  
If your network uses VLANs, you can assign one SSID to a VLAN, and client devices using the SSID are grouped in that VLAN. To  
allow users on the VLAN to access the Web page of the Wireless P-T-P Ethernet Extender, you need to enable “Enable 802.1Q  
VLAN” and assign a management VLAN ID for your device. Make sure the assigned management VLAN ID is identical to your  
network VLAN ID to enable you to access the Web page of the Wireless P-T-P Ethernet Extender.  
Figure 4-18. Management VLAN ID.  
724-746-5500 | blackbox.com  
Page 33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 5: Advanced Settings  
5. Advanced Settings  
5.1 Advanced Wireless Settings  
Open “Advanced Settings” in “Wireless” to make advanced wireless settings.  
Figure 5-1. Advanced wireless settings.  
A-MPDU/A-MSDU Aggregation  
The data rate of your AP (except wireless client mode) could be enhanced greatly with this option enabled; however, if your  
wireless clients don’t support A-MPDU/A-MSDU aggregation, we do not recommended that you enable it.  
Short GI  
Under 802.11n mode, enable it to obtain a better data rate if there is no negative compatibility issue.  
RTS Threshold  
The Wireless P-T-P Ethernet Extender sends RTS (Request to Send) frames to certain receiving stations and negotiates the sending  
of a data frame. After receiving an RTS, that STA responds with a CTS (Clear to Send) frame to acknowledge the right to start  
transmission. The setting range is 0 to 2346 in bytes. Setting it too low may result in poor network performance. We recommend  
that you leave it at its default of 2346.  
Fragmentation Length  
Specify the maximum size in bytes for a packet before data is fragmented into multiple packets. Setting it too low may result in  
poor network performance. We recommend that you leave it at its default of 2346.  
Beacon Interval  
Specify the frequency interval to broadcast packets. Enter a value between 20 and 1024.  
DTIM Interval  
Delivery Traffic Indication Message (DTIM) is contained in the data packets. It enhances the wireless transmission efficiency. The  
default is set to 1. Enter a value between 1 and 255.  
724-746-5500 | blackbox.com  
Page 34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 5: Advanced Settings  
Preamble Type  
It defines some details on the 802.11 physical layer. “Long” and “Auto” are available.  
IGMP Snooping  
Available in AP/Router mode, IGMP snooping is the process of listening to IGMP network traffic. When IGMP snooping is  
enabled, the AP will listen to IGMP membership reports, queries, and leave messages to identify the ports that are members of  
multicast groups. Multicast traffic will only be forwarded to ports identified as members of the specific multicast group or groups.  
RIFS  
RIFS (Reduced Interframe Spacing) is a means of reducing overhead and thereby increasing network efficiency.  
Link Integration  
Available under AP/Bridge/AP repeater mode. Check “Enable” to monitor the Ethernet port connection. It can inform the  
associating wireless clients as soon as it disconnects.  
TDM Coordination  
Time-Division Multiplexing Technique (TDM) helps avoid packet collisions and sends the packets much more efficiently while  
enabling higher effective throughput rates. This function is only available in AP/CPE mode. We recommend that you enable TDM  
coordination when multiple extenders will connect to the AP in your application.  
LAN2LAN CPE  
LAN2LAN CPE mode enables packet forwarding at the Layer 2 level. It is transparent for all the Layer 2 protocols.  
Space in Meters  
To decrease the chances of data retransmission at long distances, the Wireless P-T-P Ethernet Extender can automatically adjust  
the proper ACK timeout value by specifying the distance between the two nodes.  
Flow Control  
This enables the administrator to specify the incoming and outgoing traffic limit by checking “Enable Traffic Shaping.” This is only  
available in Router mode.  
NOTE: We strongly recommend that you leave most advanced settings at their defaults except “Distance in Meters.” Adjust the  
parameter for real distance; any modification may negatively impact the performance of your wireless network.  
5.2 Wireless Security Settings  
To prevent unauthorized radios from accessing data transmitting over the connection, the Wireless P-T-P Ethernet Extender has  
rock-solid security settings.  
5.2.1 Data Encryption and Authentication Settings  
Open “Profile Setting” in “Wireless” and enter “VAP Profile 1 Settings.”  
724-746-5500 | blackbox.com  
Page 35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 5: Advanced Settings  
Figure 5-2. Security settings.  
Network Authentication  
Open System: This enables any device to join the network without performing a security check.  
Shared Key: Data encryption and key are required for wireless authentication (not available in Bridge/AP Repeater mode).  
Legacy 802.1x: Available in AP/Wireless Client mode, this provides the rights to access the wireless network and wired Ethernet.  
With User and PC identity, centralized authentication, and dynamic key management, it reduces the security risk of wireless  
networks to as low as possible. To serve the 802.1x, at least one EAP type should be supported by the RADIUS Server, AP, and  
wireless client.  
NOTE: For first time users, if EAP type “TLS” is selected, you need to import a valid user certificate. To import user certificates,  
refer to Section 6.9, Certificate Settings for more details.  
WPA with RADIUS: Available in AP/Wireless Client mode, with warrant (username, password, etc.) offered by user, you can use  
this authentication with a specific RADIUS server.  
This is commonly used in large enterprise networks.  
WPA2 with RADIUS: Available in AP/Wireless Client mode, as a new version of WPA. If all the clients support WPA2, it is  
available. If it is selected, AES encryption and RADIUS server are required. It is only available in AP/Wireless Client mode.  
WPA&WPA2 with RADIUS: Available in AP mode, it enables WPA (TKIP) or WPA2 (AES) for the client. If it is selected, the data  
encryption type must be TKIP + AES and the RADIUS server must be set.  
WPA-PSK: This is a simplified WPA mode with no need for a specific authentication server. For the WPA Pre-Shared Key, pre-enter  
a key in each WLAN node. This is the commonly used in large and middle enterprise as well as a residential networks.  
WPA2-PSK: As a new version of WPA, only available if all the clients support WPA2. If it is selected, the data encryption can only  
be AES and the passphrase is required.  
WPA-PSK&WPA2-PSK: Available in AP mode, it enables WPA (TKIP) or WPA2 (AES) encryption for the client. If it is selected, the  
data encryption can only be TKIP + AES and the passphrase is required.  
724-746-5500 | blackbox.com  
Page 36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 5: Advanced Settings  
Data Encryption  
If data encryption is enabled, the key is required and only other devices using the the same key can communicate with each other.  
None: Available only when the authentication type is open system.  
64 bits WEP: Consists of 10 hexadecimal numbers.  
128 bits WEP: Consists of 26 hexadecimal numbers.  
152 bits WEP: Consists of 32 hexadecimal numbers.  
TKIP: Temporal Key Integrity Protocol, which is a kind of dynamic encryption, is co-used with WPA-PSK, etc.  
AES: Advanced Encryption Standard; it is usually co-used with WPA2-PSK, WPA, WPA2, etc.  
TKIP + AES: It allows for backwards compatibility with devices using TKIP.  
NOTES:  
We strongly recommend that you enable wireless security on your network.  
You can establish communicaton only by setting the same Authentication, Data Encryption, and Key in the Wireless P-T-P Ethernet  
Extender and other associated wireless devices.  
5.2.2 Access Control  
Access Control enables the wireless client to access the Wireless P-T-P Ethernet Extender, so a further security mechanism is  
provided. This function is available only under AP mode.  
Open “Access Control” in “Wireless” as below.  
Figure 5-3. Access Control.  
Access Control Mode  
If you select “Allow Listed,” only those clients whose wireless MAC addresses are in the access control list will be able to connect  
to your AP. While when “Deny Listed” is selected, those wireless clients on the list will not be able to connect the AP.  
724-746-5500 | blackbox.com  
Page 37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 5: Advanced Settings  
MAC Address  
Enter the MAC address of the wireless client that you want to list into the access control list, click “Apply,” and it will be added  
into the table at the bottom.  
Delete Selected/All  
Check the box before one or more MAC addresses of wireless client(s) that you want to cancel, and click “Delete Selected” or  
“Delete All” to cancel that access control rule.  
5.2.3 WDS Settings  
Extend the range of your network without using cables to link the Access Points by using the Wireless Distribution System (WDS).  
Simply put, you can link the Access Points wirelessly. Open “WDS Settings” in “Wireless.”  
Figure 5-4. WDS Settings.  
Enter the MAC address of another AP you want to connect wirelessly to into the appropriate field and click on the “Apply”  
button to save the settings.  
NOTE: WDS Settings is available only under Bridge and AP Repeater Mode.  
Bridge uses the WDS protocol that is not defined as the standard, so compatibility issues between equipment from different  
vendors may arise. Moreover, Tree or Star shape network topology should be used in all WDS use-cases (that is, if AP2 and AP3  
are specified as the WDS peers of AP1, AP2 should not be specified as the WDS peer of AP3 and AP3 should not be specified as  
the WDS peer of AP2 in any case). Avoid using mesh and ring network topologies, because they are not supported by WDS.  
724-746-5500 | blackbox.com  
Page 38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6: Management  
6. Management  
6.1 Remote Management  
The Wireless P-T-P Ethernet Extender provides remote management, including Telnet, SNMP, FTP, SSH, HTTPS, and exclusive WISE  
tool, making configuration more convenient and secure.  
With “Normal” selected, Telnet, SNMP, and FTP are activated as default remote management options. To use secure management  
tools such as SSH, HTTPS and WISE, select “Secure.” You can also choose “Customized” to enable any methods as desired.  
Figure 6-1. Remote settings.  
6.2 SNMP Management  
The Wireless P-T-P Ethernet Extender supports SNMP for convenient remote management. Open “Remote Settings” in  
“Management” as shown below. Set the SNMP parameters and obtain the MIB file before remote management.  
Figure 6-2. SNMP configuration.  
724-746-5500 | blackbox.com  
Page 39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6: Management  
Protocol Version  
Select the SNMP version, and keep it identical on the Wireless P-T-P Ethernet Extender and the SNMP manager. The Wireless P-T-P  
Ethernet Extender supports SNMP v2/v3.  
Server Port  
Change the server port for a service if needed; however, you must use the same port to use that service for remote management.  
Get Community  
Specify the password for the incoming Get and GetNext requests from the management station. By default, it is set to “public”  
and allows all requests.  
Set Community  
Specify the password for the incoming Set requests from the management station. By default, it is set to “private.”  
Trap Destination  
Specify the IP address of the station to send the SNMP traps to.  
Trap Community  
Specify the password sent with each trap to the manager. By default, it is set to “public” and allows all requests.  
Configure SNMPv3 User Profile  
For SNMP protocol version 3, click “Configure SNMPv3 User Profile” to set the details for SNMPv3 user. Check “Enable SNMPv3  
Admin/User” in advance, and continue configuring the extender.  
Figure 6-3. Configure SNMPv3 user profile.  
User Name  
Specify a user name for the SNMPv3 administrator or user. Only the SNMP commands carrying this user name are allowed to  
access the Wireless P-T-P Ethernet Extender.  
724-746-5500 | blackbox.com  
Page 40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6: Management  
Password: Specify a password for the SNMPv3 administrator or user. Only the SNMP commands carrying this password are  
allowed to access the Wireless P-T-P Ethernet Extender.  
Confirm Password: Input that password again to make sure it is your desired one.  
Access Type: Select “Read Only” or “Read and Write.”  
Authentication Protocol: Select an authentication algorithm. SHA authentication is stronger than MD5, but is slower.  
Privacy Protocol: Specify the encryption method for SNMP communication. None and DES are available.  
None: No encryption is applied.  
DES: Data Encryption Standard (DES) applies a 58-bit key to each 64-bit block of data.  
6.3 Coovachilli Settings  
Coovachilli is a captive portal management that allows WLAN users to easily and securely access the Internet. Under Router mode,  
when Coovachilli is enabled, the IEEE 802.11b/g/n Wireless Access Point will force an HTTP client on a network to see a special  
web page (usually for authentication purposes) before using the Internet normally. The browser is then redirected to a Web page  
that requires authentication. Captive portals are used at most Wi-Fi hotspots. Therefore, to use Coovachilli, you need to find  
Coovachilli service providers that have the additional services needed to make Coovahcilli work.  
Figure 6-4. Coovachilli settings.  
Radius Settings  
Primary Radius Server: Enter the name or IP address of the primary radius server.  
Secondary Radius Server: Enter the name or IP address of the primary radius server, if any.  
Radius Auth Port: Enter the port number for authentication.  
Radius Acct Port: Enter the port number for billing.  
Radius Shared Secret: Enter the secret key of the radius server.  
Radius NAS ID: Enter the name of the radius server, if any.  
724-746-5500 | blackbox.com  
Page 41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6: Management  
Radius Administrative-User  
Radius Admin Username: Enter the username of the Radius Administrator.  
Radius Admin Password: Enter the password of the Radius Administrator.  
Captive Portal  
UAM Portal URL: Enter the address of the UAM portal server.  
UAM Secret: Enter the secret password between the redirect URL and the Hotspot.  
6.4 Upgrade Firmware  
Open “Firmware Upload” in “Management” and follow the steps below to upgrade firmware locally or remotely through the  
Wireless P-T-P Ethernet Extender’s Web interface:  
Figure 6-5. Upgrade firmware.  
• Click “Browse” to select the firmware file you want to load;  
• Click “Upload” to start the upload process;  
• Wait a moment, and the system will reboot after a successful upgrade.  
CAUTION: Do NOT cut the power off during upgrade; otherwise, the system may crash.  
6.5 Backup/ Retrieve Settings  
We strongly recommend that you back up configuration information. If tragedy impacts your device, you will have access to  
restore the important files via backup. This can be done by the local or remote computer.  
Open “Configuration File” in “Management” as shown on the next page:  
724-746-5500 | blackbox.com  
Page 42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6: Management  
Figure 6-6. Backup/retrieve settings.  
Save Setting to File: When you click “Save,” a dialog box will pop up. Save it, then the configuration file ap.cfg will be  
generated and saved to your local computer.  
Load Settings from File: By clicking “Browse,” a file selection menu will appear; select the file you want to load, like ap.cfg.  
Click “Upload” to load the file. After automatically rebooting, new settings are applied.  
6.6 Restore Factory Default Settings  
The Wireless P-T-P Ethernet Extender provides two ways to restore the factory default settings:  
Restore factory default settings via Web: From “Configuration File,” “Reset” to eliminate all current settings and reboot your  
device, then default settings are applied.  
Figure 6-7. Restore settings.  
724-746-5500 | blackbox.com  
Page 43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6: Management  
Restore factory default settings via the “Reset” button: If software in the Wireless P-T-P Ethernet Extender unexpectedly crashes  
and you can no longer reset the unit via Web, you may do hardware reset via the reset button. Press and hold the button for at  
least five seconds and then release it until the PWR LED blinks.  
6.7 Reboot  
You can reboot your Wireless P-T-P Ethernet Extender from “Configuration File” in “Management.”  
Click “Reboot” and press “Yes” when prompted to start the reboot process. This takes a few minutes.  
Figure 6-8. Reboot.  
6.8 Password  
From “Password Settings” in “Management,” you can change the password to manage your IEEE 802.11b/g/n Wireless CPE.  
Enter the new password in both the “New Password” and “Confirm Password” fields; click “Apply” to save the settings.  
Figure 6-9. Password.  
The password is case-sensitive and it cannot be longer than 19 characters.  
724-746-5500 | blackbox.com  
Page 44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6: Management  
6.9 Certificate Settings  
In Client mode, when EAP-TLS is used, the RADIUS server must know which user certificates to trust. The server can trust all  
certificates issued by a given CA. To import a user certificate, from Import User Certificates, click “Browse” and specify the  
location where the user certificate is placed. Click “Import.”  
Figure 6-10. Certificate settings.  
724-746-5500 | blackbox.com  
Page 45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7: Monitoring Tools  
7. Monitoring Tools  
7.1 System Log  
System log records events that occur on the Wireless P-T-P Ethernet Extender, including station connection, disconnection, system  
reboot, etc.  
Open “System Log” in “Tools.”  
Figure 7-1. System log.  
Remote Syslog Server  
Enable Remote Syslog: Enable System log to alert remote server.  
IP Address: Specify the IP address of the remote server.  
Port: Specify the port number of the remote server.  
7.2 Site Survey  
Only available under Wireless Client mode, site survey allows you to scan all the APs within coverage.  
Open “Site Survey” in “Tools” as shown below and select the desired AP to connect.  
724-746-5500 | blackbox.com  
Page 46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7: Monitoring Tools  
Figure 7-2. Site survey.  
7.3 Ping Watchdog  
If the extender unexpectedly disconnects and cuts off your ability the log in to the unit, use the ping watchdog to reboot.  
Figure 7-3. Ping watchdog.  
Ping Watchdog  
Enable Ping Watchdog: To activate ping watchdog, check this checkbox.  
IP Address to Ping: Specify the IP address of the remote unit to ping.  
Ping Interval: Specify the interval time to ping the remote unit.  
Startup Delay: Specify the startup delay time to prevent reboot before the Wireless P-T-P Ethernet Extender is fully initialized.  
Failure Count To Reboot: If the ping timeout packets reached the value, the Wireless P-T-P Ethernet Extender will reboot  
automatically.  
724-746-5500 | blackbox.com  
Page 47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7: Monitoring Tools  
7.4 Data Rate Test  
The Data Rate Test enables you to test the current RSSI at each data rate between your Wireless P-T-P Ethernet Extenders.  
Figure 7-4. Data rate test.  
7.5 Antenna Alignment  
In Bridge mode, when the bridges are not easily visible from the location where the dish will be installed, the antenna alignment  
tool can help you evaluate the position of the unit and adjust the angle of the antenna more precisely. Keep in mind that in real  
circumstances a lot of additional factors should be taken into account when your unit is installed. These factors include various  
obstacles (buildings, trees), the landscape, the altitude, transponder orientation, polarization, etc.  
To use the tool, select the desired remote WDS bridge and click “Start.” The Web page will display the measured signal strength,  
RSSI, and transmit/receive packets. If the signal quality is not good, adjust the antenna and see if the quality improves.  
724-746-5500 | blackbox.com  
Page 48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7: Monitoring Tools  
Figure 7-5. Antenna alignment.  
7.6 Speed Test  
The speed test monitors the current data transmission (TX) and data reception (RX) rate with the remote Wireless P-T-P Ethernet  
Extender. Enter the IP address of the remote extender, type in the user name/password and click “Test.” The result will display in  
the bottom STATUS. You may test single TX/RX or bi-directional.  
Figure 7-6. Speed test.  
724-746-5500 | blackbox.com  
Page 49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 8: Status  
8. Status  
8.1 View Basic Information  
Open “Information” in “Status” to check the basic information of the CPE, which is read-only.  
Information includes system information, LAN settings, wireless setting, and interface status. Click “Refresh” at the bottom to get  
the real-time information.  
Figure 8-1. Basic information.  
8.2 View Association List  
Open “Connections” in “Status” to check the information for associated wireless devices, such as MAC address, signal strength,  
connection time, IP address, etc. All are read-only. Click “Refresh” at the bottom to update the current association list.  
Figure 8-2. Connection.  
724-746-5500 | blackbox.com  
Page 50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 8: Status  
By clicking on the MAC address of the selected device on the Web, you may see more details including device name, connection  
time, signal strength, noise floor, ACK timeout, link quality, IP information, current data rate, and current TX/RX packets.  
Figure 8-3. Association node details.  
8.3 View Network Flow Statistics  
Open “Statistics” in “Status” to check the data packets received on and transmitted from the wireless and Ethernet ports. Click  
“Refresh” to view current statistics.  
Figure 8-4. Network flow statistics.  
724-746-5500 | blackbox.com  
Page 51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 8: Status  
Poll Interval: Specify the refresh time interval in the box beside “Poll Interval” and click “Set Interval” to save the settings. “Stop”  
discontinues the auto refresh of network flow statistics.  
8.4 View ARP Table  
Open “ARP Table” in “Status” as shown below. Click “Refresh” to view current table.  
Figure 8-5. ARP table.  
8.5 View Bridge Table  
Open “Bridge Table” in “Status” as below. Click “Refresh” to view current connected status.  
Figure 8-6. Bridge table.  
8.6 View Active DHCP Client Table  
Open “DHCP Clients” in “Status” as shown below to check the assigned IP address, MAC address, and time expired for each  
DHCP leased client. Click “Refresh” to view current table.  
724-746-5500 | blackbox.com  
Page 52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 8: Status  
Figure 8-7. DHCP client table.  
8.7 View Network Activities  
The network activities enables you to monitor the current Wireless and Ethernet TX/RX data traffic in graphical and numerical  
form on the Skyport Web. The chart scale and throughput dimension (bps, kbps, Mbps) changes dynamically according to the  
mean throughput value. You can manually update throughput statistics using the “Refresh” button.  
Figure 8-8. Network activities.  
724-746-5500 | blackbox.com  
Page 53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 9: Troubleshooting  
9. Troubleshooting  
This chapter provides troubleshooting procedures for basic problems with the Wireless P-T-P Ethernet Extender.  
9.1 Frequently Asked Questions  
Q 1. What is the MAC address of the Wireless P-T-P Ethernet Extender?  
MAC Address distinguishes itself by a unique identity among network devices. It appears in two places:  
1. Each device has a label posted with the MAC address. Please see below.  
Figure 9-1. MAC address.  
2. On the Wireless P-T-P Ethernet Extender Web-based management interface, you can view the MAC Address from “View Basic  
Information.”  
Q 2. How do I reset the unit to default settings?  
You may restore factory default settings in “Configuration File” from “Management.”  
Q 3. How do I backup and retrieve my configuration settings?  
You backup the file by generating a configuration file or retrieve the settings you have backed up previously in “Configuration  
File” from “Management.”  
Q 4. What if I cannot access the Web-based management interface?  
Please check the following:  
• Make sure the power supply is working; try to power on the unit again.  
• Make sure the IP address of PC is correct (in the same network segment as the unit).  
• Login to the unit via another browser, such as Firefox.  
• Hardware reset the unit.  
Q 5. What if the wireless connection is not stable after associating with an AP under wireless client mode?  
• Since the Wireless P-T-P Ethernet Extender comes with a built-in directional antenna, we recommend that you make the  
Wireless P-T-P Ethernet Extender face the direction where the AP is for best connection quality.  
• In addition, you can start “Site Survey” in “Wireless Basic Settings” to check the signal strength. If it is weak or unstable (the  
smaller the number is, the weaker the signal strength is), join another available AP for a better connection.  
724-746-5500 | blackbox.com  
Page 54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 9: Troubleshooting  
9.2 Contacting Black Box  
If you determine that your Wireless P-T-P Ethernet Extender is malfunctioning, do not attempt to alter or repair the unit. It  
contains no user-serviceable parts. Contact Black Box Technical Support at 724-746-5500 or [email protected].  
Before you do, make a record of the history of the problem. We will be able to provide more efficient and accurate assistance if  
you have a complete description, including:  
• the nature and duration of the problem.  
• when the problem occurs.  
• the components involved in the problem.  
• any particular application that, when used, appears to create the problem or make it worse.  
9.3 Shipping and Packaging  
If you need to transport or ship your Wireless P-T-P Ethernet Extender:  
• Package it carefully. We recommend that you use the original container.  
• If you are returning the unit, make sure you include everything you received with it. Before you ship for return or repair, contact  
Black Box to get a Return Authorization (RA) number.  
724-746-5500 | blackbox.com  
Page 55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix A: ASCII  
Appendix A. ASCII  
WEP can be configured with a 64-bit, 128-bit or 152-bit Shared Key (hexadecimal number or ACSII). As defined, the hexadecimal  
number is represented by 0-9, A-F or a-f; ACSII is represented by 0-9, A-F, a-f or punctuation. Each one consists of a two-digit  
hexadecimal.  
Table A-1. ASCII.  
ASCII  
Hex  
ASCII  
Hex  
ASCII  
Hex  
ASCII  
Hex  
Character  
Equivalent  
Character  
Equivalent  
Character  
Equivalent  
Character  
Equivalent  
1
"
#
$
%
&
"
(
21  
22  
23  
24  
25  
26  
27  
28  
29  
2A  
2B  
2C  
2D  
2R  
2F  
9
:
39  
3A  
3B  
3C  
3D  
3E  
3F  
Q
R
S
T
U
V
W
X
Y
Z
[
51  
52  
53  
54  
55  
56  
57  
58  
59  
5A  
5B  
5C  
5D  
5E  
5F  
i
69  
6A  
6B  
6C  
6D  
6E  
6F  
j
;
k
l
<
=
>
?
m
n
o
p
q
r
@
A
B
C
D
E
40  
41  
42  
43  
44  
45  
46  
47  
48  
49  
4A  
4B  
4C  
4D  
4E  
4F  
70  
71  
72  
73  
74  
75  
76  
77  
78  
79  
7A  
7B  
7C  
7D  
7E  
)
-
+
,
s
\
t
-
]
u
v
w
x
y
z
(
.
F
^
_
’
/
G
H
i
0
1
2
3
4
5
6
7
8
30  
31  
32  
33  
34  
35  
36  
37  
38  
60  
61  
62  
63  
64  
65  
66  
67  
68  
a
b
c
J
K
L
d
e
f
{
M
N
O
P
}
-
g
h
50  
724-746-5500 | blackbox.com  
Page 56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix B. SSH Settings  
Appendix B. SSH Settings  
Table B-1. CLI commands.  
get  
set  
del  
Keyword  
Descriptions  
√
√
time  
-time seting  
√
√
√
√
√
√
√
√
√
√
√
-now  
-current system time  
-time zone  
√
√
√
√
√
√
-zone  
-NTPUpdate  
-servertype  
-IP  
-NTP Update  
-server type  
-IP  
-Manual IP  
-Manual IP  
system  
-system setting  
-system firmware version  
-system MAC address  
-system name  
-country/region  
-swverson  
-systemmac  
-devname  
-country  
√
√
√
√
√
√
-ethernet1DataRate  
-ethernet2DataRate  
-macclone  
-ether port 1 data rate  
-ether port 2 data rate  
-mac clone enable  
√
√
√
√
√
√
√
√
√
√
√
√
√
√
-clonedmac  
-poepower  
-stp  
-cloned mac address  
-secondary RJ45 power  
-Spaning Tree  
-stpForwardDelay  
-gpslatitude  
-gpslongitude  
-STP forward delay  
-gps latitude  
-gps longitude  
√
√
√
√
√
√
√
√
√
√
ipset  
-networkmode  
-bridge  
-network mode select (bridge or router)  
-bridge mode ip settings  
-fixed/dynamical ip (dhcp client)  
-ip address  
-iptype  
-ipaddr  
724-746-5500 | blackbox.com  
Page 57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix B. SSH Settings  
Table B-1 (Continued). CLI commands.  
get  
set  
del  
Keyword  
Descriptions  
√
√
-netmask  
-gateway  
-dns1  
-subnet mask  
√
√
√
√
√
√
√
√
√
√
√
-gateway ip address  
-dns1  
√
√
√
√
√
√
√
√
√
√
√
-dns2  
-dns2  
-router  
-router mode ip settings  
-wan ip settings  
-router mode access type  
-static ip address  
-static subnet mask  
-static gateway ip address  
-static dns1  
-wan  
-accesstype  
-staticipadd  
-staticnetmask  
-staticgateway  
-staticdns1  
-staticdns2  
-static dns2  
√
√
√
-dhcpclient hostname  
-pppoeconnectstatis  
-pppoelocalip  
-dhcp client hostname  
-pppoe connect status  
-obtains IP frrom pppoe server  
√
√
√
√
√
√
√
√
√
√
√
√
-pppoestaticipaddr  
-pppoeusername  
-pppoepassword  
-pppoeservername  
-pppoeconnectmode  
-pppoeidletime  
-pppoe static ip address  
-pppoe username  
-pppoe password  
-pppoe server name  
-pppoe connect mode  
-pppoe idle time  
√
√
√
√
√
√
√
√
√
√
-lan  
-lan ip settings  
-ipaddr  
-lan ip address  
-netmask  
-lan subnet mask  
-dhcp server enable  
-dhcp server ip start  
-dhcpserverenable  
-dhcpserveripstart  
724-746-5500 | blackbox.com  
Page 58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix B. SSH Settings  
Table B-1 (Continued). CLI commands.  
get  
set  
del  
Keyword  
Descriptions  
√
√
-dhcpserveripend  
-dhcp server ip end  
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
-dhcpserverleasetime  
-dhcprelayenable  
-dhcpserverip  
-dhcp server leasetime  
-dhcp relay enable  
-dhcp server ip  
wlan  
-wlan setting  
-operationmode  
-ssid  
-operation mode  
-wireless network name  
-wireless SSID broadcast  
-radio switch  
-ssidhided  
-radio  
-wirelessmode  
-wireless mode  
-HTprotect  
-HT protect  
-wireless frequency/channel (depends on  
country and wireless mode)  
√
√
-frequency/channel  
√
√
-power  
-rate  
-power  
-rate  
√
√
√
√
√
√
√
-antenna  
-antennaGain  
-wmm  
-antenna type  
-antenna gain settings  
-wmm settings  
-wireless isolate communication between  
clients  
√
√
-isolation  
√
√
√
√
-maxStaNum  
-StaNumLmt  
-max sta connection number  
-manually limit the number of stations  
√
√
√
√
√
√
√
√
√
√
-spaceInMeter  
-LinkIntegration  
-channelMode  
-channelOffset  
-extension  
-wireless bwa space in meter setting  
-wireless bwa coverage class setting  
-channel mode  
-channel offset of 40 MHz  
-extension  
724-746-5500 | blackbox.com  
Page 59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix B. SSH Settings  
Table B-1 (Continued). CLI commands.  
get  
set  
del  
Keyword  
Descriptions  
√
√
-A-MPDU  
-A-MSDU  
-shortGI  
-RIFS  
-A-MPDU  
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
-A-MSDU  
-shortGI  
-rifs  
-RTS  
-RTS  
-fragment  
-beacon  
-DTIM  
-fragment  
-beacon  
-DTIM  
-preamble  
-IGMP  
-preamble  
-IGMP  
-stdm  
-stdm setting  
-CPE Type  
-cpeType  
√
√
√
-authentication  
-encryption  
-key  
-wireless authentication type  
-wireless data encryption  
-wireless wep key setting  
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
-type  
-default  
-1  
-wireles wep key type  
-wireless wep default key index  
-wireless wep key 1  
√
√
√
√
√
-2  
-wireless wep key 2  
-3  
-wireless wep key 3  
-4  
-wireless wep key 4  
-wpa  
-wireless WPA setting  
-wireless pre-shared key (PSK) for  
WPA-PSK  
√
√
√
-psk  
√
√
√
√
-reauthtime  
-keyupdate  
-wireless WPA re-auth period (in seconds)  
-enable wireless WPA global key update  
√
√
√
-eap  
-WPA EAP setting  
724-746-5500 | blackbox.com  
Page 60  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix B. SSH Settings  
Table B-1 (Continued). CLI commands.  
get  
set  
del  
Keyword  
Descriptions  
√
√
√
-eaptype  
-WPA EAP Type  
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
-innereaptype  
-username  
-WPA inner EAP Type  
-WPA user name  
-loginname  
-password  
-WPA login name  
-WPA password  
-usercert  
-WPA cert file  
-privatekeypassword  
-WPA private key password  
-traffic shaping  
-trafficshaping  
-enable  
-enable Traffic Shaping  
-Incoming Traffic Limit  
-Incoming Traffic Burst  
-Outgoing Traffic Limit  
-downlimit  
-downburst  
-uplimit  
√
√
√
-upburst  
-Outgoing Traffic Burst  
-WDS Remote Mac  
-local macAddr  
-wdsMac  
√
√
√
√
√
√
-local  
√
√
√
√
√
√
-remote1  
-remote2  
-remote3  
-remote4  
-remote macAddr1  
-remote macAddr2  
-remote macAddr3  
-remote macAddr4  
-wdsSeparation  
-association  
-WDS Separation  
-list of associated wireless clients  
vapprofile 1  
(2,3, etc.)  
√
√
-VAP setting  
√
√
√
√
√
√
√
√
-active  
-on/off this vap  
-profileName  
-ssid  
-Name of profile  
-ssid of this vap  
-ssidhided  
-Broadcast SSID Enable or Disable  
724-746-5500 | blackbox.com  
Page 61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix B. SSH Settings  
Table B-1 (Continued). CLI commands.  
get  
set  
del  
Keyword  
Descriptions  
√
√
-vlanID  
-vlanID of this vap  
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
-Isolation  
-wmm  
-wireless separation  
-WMM Support  
-MaxStaNum  
-StaNumLmt  
-authentication  
-encyrption  
-default  
-Max Station Number  
-Manually limit the number of stations  
-wireless autheticatoin type  
-wireless data encryption  
-wireless wep default key index  
-wireless WPA setting  
-wpa  
-association  
-list of associated wireless clients  
-vlan setting  
vlan  
-active  
-enable 802.1Q VLAN  
√
√
√
-manageiD  
-Management VLAN ID  
-radius setting  
radius  
√
√
√
√
√
√
√
√
-IPaddr  
-IP address  
√
√
√
√
√
√
-port  
-port  
-shared secret  
-Shared Secret  
firewall  
-firewall setting  
-srcipfilter  
-source ip filter settings  
-source ip filter enable  
-add a source ip filter rule  
-delete source ip filter rule  
-enable  
-addrule  
-delerle  
-rulelist  
√
√
√
√
-show source ip filter rule lists  
-source port filter settings  
-source port filter enable  
-add a source port filter rule  
√
√
√
-srcpportfilter  
-enable  
-addrule  
724-746-5500 | blackbox.com  
Page 62  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix B. SSH Settings  
Table B-1 (Continued). CLI commands.  
get  
set  
del  
Keyword  
Descriptions  
√
-delerule  
-rulelist  
-delete source port filter rule  
√
√
√
√
-show source port filter rule lists  
-destination port filter settings  
-destination port filter enable  
-add a destination port filter rule  
-delete destination port filter rule  
-show destination port filter rule lists  
-port forward settings  
√
√
√
√
-destportfilter  
-enable  
-addrule  
-delerule  
-rulelist  
√
√
√
√
√
√
√
√
-portforward  
-enable  
-addrule  
-delerule  
-rulelist  
-port forward enable  
-add a port forward rule  
-delete port forward rule  
√
-show port forward rule lists  
√
√
√
√
-dmzenable  
-dmzipaddr  
-dmz enable  
-dmz ip address  
√
√
√
√
√
√
√
√
remote  
-remote management setting  
√
√
√
√
√
√
√
-privacy  
-telnet  
-snmp  
-ftp  
-radius IP address  
-enable telnet  
-enable snmp  
-enable ftp  
-ssh  
-enable ssh  
-forcehttps  
-wise  
-force https  
-enable wise tools  
√
√
√
√
√
√
√
√
snmp  
-SNMP setting  
-version  
-Protocol Version  
-Server Port  
-port  
-getCommunity  
-SNMP Read Community  
724-746-5500 | blackbox.com  
Page 63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix B. SSH Settings  
Table B-1 (Continued). CLI commands.  
get  
set  
del  
Keyword  
Descriptions  
√
√
-setCommunity  
-trapdestination  
-trapcommunity  
-v3Admin  
-SNMP Write Community  
√
√
√
√
√
-Trap Destination  
-Trap Community  
-v3Admin  
√
√
√
√
√
√
√
√
√
√
√
-on  
-Enable SNMPv3Admin  
-name  
-name  
-password  
-accessType  
-authetica  
-Privacy  
-password  
√
√
√
√
√
-access type  
-Authentication Protocol  
-privacy protocol  
-v3User  
-v3User  
-on  
-Enable SNMPv3User  
√
√
√
-name  
-name  
-password  
-accessType  
-password  
-access type  
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
-authentication  
-Privacy  
-Authentication Protocol  
-privacy protocol  
coovachilli  
-CoovaChilli setting  
-coovaChilliEnable  
-Coovachilli Enable  
-primaryRadiusServer  
-secondaryRadiusServer  
-radiusAuthPort  
-Primary RADIUS Server  
-Secondary RADIUS Server  
-RADIUS Authentication Port  
√
√
√
√
√
√
√
√
-radiusAcctPort  
-RADIUS Accounting Port  
-RADIUS Shared Secret  
-RADIUS Nasid  
-radiusSharedSecret  
-radiusNasid  
-radiusAdminUsername  
-RADIUS Admin Username  
724-746-5500 | blackbox.com  
Page 64  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix B. SSH Settings  
Table B-1 (Continued). CLI commands.  
get  
set  
del  
Keyword  
Descriptions  
√
√
-radiusAdminPassword  
-RADIUS Admin Password  
√
√
√
√
√
√
√
√
√
√
√
-uamPortalUrl  
-uamSecret  
-UAM Portal URL  
-UAM Secret  
√
√
√
√
√
√
√
√
√
√
√
syslog  
-syslog  
-client  
-ipaddr  
-port  
-enable syslog client  
-syslog server IP address  
-syslog server port number  
-syslog clear  
-clear  
pingwdg  
-ping watchdog  
-enable  
-enable  
-interval  
-startdelay  
-interval  
-startup delay  
√
√
√
-failcount  
-ip  
-failure count  
-ip address  
√
√
√
acl  
-access control  
√
-mode  
-delete  
-list  
-enable wireless access control (ACL)  
-delete a local ACL  
√
√
√
-delete or display all local ACL addresses  
-add mac address to Current Access  
Control List  
√
-MacAddr  
√
√
√
√
statistics  
-statistics  
-Wireless  
-Ethernet  
-Wireless LAN  
-Ethernet LAN  
√
log list  
password  
reset  
-syslog list  
√
√
√
√
-system password  
-restore factory  
-reboot system  
-logout from CLI  
reboot  
exit  
LICENSE Version 2  
724-746-5500 | blackbox.com  
Page 65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES  
724-746-5500 | blackbox.com  
Page 66  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES  
724-746-5500 | blackbox.com  
Page 67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Black Box Tech Support: FREE! Live. 24/7.  
Tech support the  
way it should be.  
Great tech support is just 30 seconds away at 724-746-5500 or blackbox.com.  
About Black Box  
Black Box provides an extensive range of networking and infrastructure products. You’ll find everything from cabinets and racks  
and power and surge protection products to media converters and Ethernet switches all supported by free, live 24/7 Tech Support  
available in 30 seconds or less.  
© Copyright 2012. Black Box Corporation. All rights reserved.  
LWE100A User Manual, version 1  
724-746-5500 | blackbox.com  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Belkin Network Router F7D6301 User Manual
Black Box Network Hardware ME800A User Manual
Black Decker Can Opener KEC600 User Manual
Breville Juicer JC7 User Manual
Brother All in One Printer DCP 7030 User Manual
Bushnell Binoculars 280750 User Manual
Cambridge Audio CD Player CD5 User Manual
Campbell Hausfeld Air Compressor FP2095 User Manual
Campbell Hausfeld Pressure Washer PW1510 User Manual
Casio Projector XJ A135 User Manual