USER’S GUIDE
BOXLIGHT XP-5t
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
All the safety and operating instructions should be read before
the product is operated.
This projector should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supplied, consult your authorized dealer or
local power company.
Read all of the instructions given here and retain them for later
use. Unplug this projector from AC power supply before
cleaning. Do not use liquid or aerosol cleaners. Use a damp
cloth for cleaning.
Do not overload wall outlets and extension cords as this can
result in fire or electric shock. Do not allow anything to rest on
the power cord. Do not locate this projector where the cord
may be damaged by persons walking on it.
Follow all warnings and instructions marked on the projector.
For added protection to the projector during a lightning storm,
or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet. This will prevent damage
due to lightning and power line surges.
Do not attempt to service this projector yourself as opening or
removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service
personnel.
Unplug this projector from wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
Do not expose this unit to rain or use near water... for
example, in a wet basement, near a swimming pool, etc...
Do not use attachments not recommended by the
manufacturer as they may cause hazards.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the projector to normal operation.
e. If the projector has been dropped or the cabinet has been
damaged.
f. When the projector exhibits a distinct change in
performance-this indicates a need for service.
Do not place this projector on an unstable cart, stand, or table.
The projector may fall, causing serious injury to a child or
adult, and serious damage to the projector. Use only with a
cart or stand recommended by the manufacturer, or sold with
the projector. Wall or shelf mounting should follow the
manufacturer's instructions, and should use a mounting kit
approved by the manufacturers.
An appliance and cart combination should
be moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the appliance and cart
combination to overturn.
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or injury to persons.
Upon completion of any service or repairs to this projector, ask
the service technician to perform routine safety checks to
determine that the projector is in safe operating condition.
Slots and openings in the back and bottom of the cabinet are
provided for ventilation, to insure reliable operation of the
equipment and to protect it from overheating.
The openings should never be covered with cloth or other
materials, and the bottom opening should not be blocked by
placing the projector on a bed, sofa, rug, or other similar
surface. This projector should never be placed near or over a
radiator or heat register.
This projector should not be placed in a built-in installation
such as a book case unless proper ventilation is provided.
Voor de klanten in Nederland
Bij dit product zijn batterijen
geleverd.
Wanneer deze leeg zijn,
moet u ze niet weggooien
maar inleveren als KCA.
Never push objects of any kind into this projector through
cabinet slots as they may touch dangerous voltage points or
short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the projector.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPLIANCES
Federal Communication Commission Notice
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
AC POWER CORD REQUIREMENT
The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.
AC Power Cord for the United States and Canada :
AC Power Cord used in the United States and Canada is listed by the Underwriters
Laboratories (UL) and certified by the Canadian Standard Association (CSA).
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure
that the plug will fit into the power outlet. Do not try to defeat this safety feature.
Should you be unable to insert the plug into the outlet, contact your electrician.
GROUND
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
FEATURES AND DESIGN
6
7
COMPUTER MODE
22
SELECTING COMPUTER MODE
22
22
23
SELECTING COMPUTER SYSTEM
PREPARATION
COMPATIBLE COMPUTER SPECIFICATIONS
PC ADJUSTMENT
24
NAME OF EACH PART OF THE PROJECTOR
7
8
8
9
9
PICTURE IMAGE ADJUSTMENT
ADJUST PICTURE IMAGE MANUALLY
NORMAL FUNCTION
26
26
26
27
SETTING-UP THE PROJECTOR
CONNECTING THE AC POWER CORD
POSITIONING THE PROJECTOR
ADJUSTABLE FEET
AUTO IMAGE FUNCTION
PICTURE POSITION ADJUSTMENT
PICTURE SCREEN ADJUSTMENT
27
28
MOVING THE PROJECTOR
10
CONNECTING THE PROJECTOR 11
VIDEO MODE
29
TERMINALS OF THE PROJECTOR
CONNECTING TO THE VIDEO EQUIPMENT
CONNECTING TO THE COMPUTER
11
12
13
SELECTING VIDEO MODE
29
29
30
30
SELECTING VIDEO SOURCE
SELECTING COLOR SYSTEM
PICTURE SCREEN ADJUSTMENT
PICTURE IMAGE ADJUSTMENT
ADJUSTING THE PICTURE IMAGE MANUALLY
NORMAL FUNCTION
31
31
31
BEFORE OPERATION
14
OPERATION OF THE REMOTE CONTROL
OPERATING RANGE
14
14
15
SETTING
32
REMOTE CONTROL BATTERIES INSTALLATION
TOP CONTROLS AND INDICATORS
16
SETTING MENU
SETTING LANGUAGE
32
33
OPERATING ON-SCREEN MENU
HOW TO OPERATE THE ON-SCREEN MENU
FLOW OF ON-SCREEN MENU
MENU BAR
17
17
17
18
APPENDIX
34
BASIC OPERATION
19
OPERATING WIRELESS MOUSE
34
MAINTENANCE
35
35
35
35
36
36
TURNING ON / OFF THE PROJECTOR
ADJUSTING THE IMAGE
ZOOM ADJUSTMENT
19
TEMPERATURE WARNING INDICATOR
AIR FILTER CARE AND CLEANING
CLEANING THE PROJECTION LENS
LAMP REPLACEMENT
20
20
20
20
21
21
21
FOCUS ADJUSTMENT
KEY STONE ADJUSTMENT
NO SHOW FUNCTION
PICTURE FREEZE FUNCTION
P-TIMER FUNCTION
LAMP REPLACEMENT MONITOR TIMER
TROUBLESHOOTING
TECHNICAL SPECIFICATIONS
37
39
SOUND ADJUSTMENT
SOUND VOLUME ADJUSTMENT
SOUND MUTE ADJUSTMENT
21
21
21
TRADEMARKS
● Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.
● IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.
● Windows and PowerPoint are registered trademarks of Microsoft Corporation.
● Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its
respective corporation.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES AND DESIGN
This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of
use. The projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal
display (LCD) technology.
● Compact Design
● Multi-Scan System
This projector is extremely compact in size and
weight. It is designed to carry and work anywhere
you wish to use.
This projector has Multi-Scan System to conform to
almost all computer output signals quickly. There
is no need for troublesome manual adjustment of
frequency and other settings.
● Compatibility
● One-Touch Auto Imaging
This projector widely accepts various video and
computer input signals including;
Incoming computer video signals are recognized
and the best setting is automatically selected by
the Auto Image function.
No complicated setup is necessary and projection
is always precise.
● Computers
IBM-compatible and Macintosh computers up
to 1280 x 1024 resolution.
● 6 Color Systems
NTSC, PAL, SECAM, NTSC 4.43, PAL-M or
PAL-N color system can be connected.
● Digital Zoom (Computer Mode only)
The Digital Zoom magnifies the image up to 16
times, allowing you to focus on crucial information
at a presentation.
● Component Video
Component video signals, such as a DVD
player output high definition TV signals
including 480i, 480p, 575i, 575p, 720p, 1035i
or 1080i, can be connected.
● Keystone Correction
● S-Video
Positioning height of the projector may result in
distorted images being displayed in a trapezoid
shape. Keystone Correction solves this problem
by digitally altering the projection to produce
undistorted images.
S-Video signals, such as a S-VHS VCR
output signals, can be connected.
● High Resolution Image
This projector provides 1024 x 768 dots resolution
for computer input and 550 horizontal TV lines.
The resolution from the computer between XGA
(1024 x 768) and SXGA (1280 x 1024) is
compressed into 1024 x 768 dots. This projector
cannot display image of over 1280 x 1024 dots.
When the resolution of your computer is over than
1280 x 1024, reset the computer output for lower
resolution.
● Power Management
Power Management function is provided to reduce
power consumption while the projector is not in
use.
This Power Management function operates to turn
the Projection Lamp off when the projector detects
signal interruption and any button is not pressed
over 5 minutes. The Projection Lamp is
automatically turned on again when the projector
detects the signal or any operation button is
pressed.
● Multilanguage Menu Display
This projector is shipped with this function ON.
Operation menu is displayed in; English, Deutsch,
Français, Italiano, Español, or Japanese.
● Wireless Mouse
The Remote Control Unit supplied with this
projector has Wireless Mouse function for the
connected computer. This function enables you to
operate both projector and computer with this
Remote Control Unit only.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
NAME OF EACH PART OF THE PROJECTOR
FRONT OF THE CABINET
AIR INTAKE VENTS
PROJECTION LENS
(Both sides and Rear)
This projector is equipped with cooling
fans for protection from overheating.
Pay attention to the following to ensure
proper ventilation and avoid a possible
risk of fire and malfunction.
ZOOM RING
● Do not cover the vent slot.
● Keep sides and rear clear of any
obstructions. Obstructions may block
cooling air.
FOCUS RING
SPEAKER
(Monaural)
LENS COVER
POWER CORD CONNECTOR
INFRARED
REMOTE RECEIVER
EXHAUST VENT
HOT AIR EXHAUSTED !
BACK OF THE CABINET
Air blown from the exhaust vent is hot.
When using or installing the projector, the
following precautions should be taken.
● Do not put a flammable object near this vent.
● Keep the side grills at least 3’ (1m) away
from any object, especially heat-sensitive
object.
● Do not touch this area, especially screws
and metallic parts. This area will become
hot while the projector is used.
This projector detects the internal
temperature and automatically controls the
operating power of the Cooling Fans.
TERMINALS
AND CONNECTORS
BOTTOM OF THE CABINET
LAMP COVER
ADJUSTABLE FEET
AND
FEET LOCK LATCHES
AIR INTAKE VENTS
AND AIR FILTERS
These Air Intake Vents
should not be blocked.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
SETTING-UP THE PROJECTOR
CONNECTING THE AC POWER CORD
This projector uses nominal input voltages of 100-120 V
or 200-240 V AC. The projector automatically selects the
correct input voltage. It is designed to work with single-
phase power systems having a grounded neutral
conductor. To reduce the risk of electrical shock, do not
plug into any other type of power system.
Consult your authorized dealer or service station if you
are not sure of the type of power supply being in use.
Connect the projector with the peripheral equipment
before turning the projector on. (Refer to pages 11 ~ 13
for connection.)
Connect the AC Power Cord (supplied)
to the projector.
The AC outlet must be near this
equipment and must be easily
accessible.
CAUTION
For safety, unplug the AC Power Cord when the appli-
ance is not used.
When this projector is connected to the outlet with the
AC Power Cord, the appliance is in Stand-by Mode
and consumes a little electric power.
NOTE ON THE POWER CORD
The AC Power Cord must meet the requirement of the country where you use the projector.
Confirm the AC plug type with the chart below. The proper AC power cord must be used.
If the supplied AC Power Cord does not match the AC outlet, contact your sales dealer.
Projector side
AC Outlet side
For the U.S.A. and Canada
For Continental Europe
Ground
To the POWER CORD
CONNECTOR on the
projector.
To the AC Outlet.
(120 V AC)
To the AC Outlet.
(200 - 240 V AC)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
POSITIONING THE PROJECTOR
● This projector is designed to project on a flat
ROOM LIGHT
projection surface.
● The projector can be focused from 5.2’(1.6m) ~
26.3’(8.0m).
The brightness in the room has a great
influence on the picture quality. It is
recommended to limit ambient lighting in
order to provide the best image.
● Refer to the figure below to adjust the screen size.
26.3’ (8.0m)
200”
19.7’ (6.0m)
13.1’ (4.0m)
150”
Max. Zoom
7.8’ (2.4m)
167”
100”
83”
H1
5.2’ (1.6m)
41”
125”
60”
50”
Min. Zoom
H2
34”
34”
60”
100”
150”
200”
Screen Size
(W x H) mm
690 x 518
1219 x 914
33.2”(844mm)
2.8”(70mm)
2032 x 1524
55.4”(1407mm)
4.6”(117mm)
3048 x 2286
83.1”(2110mm)
6.9”(176mm)
4064 x 3048
110.8”(2814mm)
9.2”(234mm)
18.82”(478mm)
1.57”(40mm)
Height (H1)
Height (H2)
ADJUSTABLE FEET
Picture tilt and projection angle can be adjusted by
rotating the ADJUSTABLE FEET. Projection angle can
be adjusted to 7.6 degrees.
Lift the front of the projector and pull the FEET LOCK
LATCHES on both sides of the projector.
1
Release the FEET LOCK LATCHES to lock the
ADJUSTABLE FEET and rotate the ADJUSTABLE FEET
to fine tune the position and the tilt.
2
To shorten the ADJUSTABLE FEET, lift the front of the
projector and pull and undo the FEET LOCK LATCHES.
3
FEET LOCK
LATCHES
The position and the keystone distortion of the image can
be adjusted using the Menu Operation. (Refer to P 20,
28 and 30.)
ADJUSTABLE FEET
9
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
MOVING THE PROJECTOR
When moving the projector, replace the lens cover and retract the feet to prevent damage to the lens and
cabinet.
When this projector is not in use for an extended period, put it into the case (carrying bag) supplied with this
projector.
CAUTION
The Carrying Bag (supplied) is intended for protection from dust and scratches on the surface of the cabinet, and
it is not designed to protect the LCD projector from external forces. Do not transport the projector through a
courier or transport services with this bag. The projector can be damaged. When handling the projector, do not
drop or bump the projector, subject it to strong forces or put other things on the cabinet.
CAUTION IN CARRYING OR TRANSPORTING THE PROJECTOR
● Do not drop or bump the projector, otherwise damages or malfunctions may result.
● When carrying the projector, use a suitable carrying case.
● Do not transport the projector by using a courier or transport service in an unsuitable transport case. This
may cause damage to the projector. To transport the projector through a courier or transport service,
consult your dealer for best way.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING THE PROJECTOR
TERMINALS OF THE PROJECTOR
VIDEO INPUT JACKS
(VIDEO/Y, Pb/Cb, Pr/Cr)
S-VIDEO INPUT JACK
Connect the S-VIDEO output
from the video equipment to this
terminal. (Refer to P12.)
Connect the composite video
output from the video equipment
to the VIDEO/Y jack or connect
the component video outputs to
the Y/VIDEO, Pb/Cb and Pr/Cr
jacks. (Refer to P12.)
VIDEO
Y – Pb/Cb – Pr/Cr
S –VIDEO
AUDIO INPUT JACK
AUDIO OUT
AV
RESET
COMPUTER
Connect the audio output from
the video equipment to this
terminal. (Refer to P12.)
RESET BUTTON
AUDIO
IN
This projector uses a micro
processor to control the unit.
Occasionally, the micro
processor may malfunction and
need to be reset. This can be
done by pressing the RESET
button with a pen, which will
shut down and restart the unit.
Do not use the RESET function
excessively.
CONTROL PORT
COMPUTER IN
COMPUTER AUDIO INPUT JACK
Connect the audio output from
the computer to this terminal.
(Refer to P13.)
CONTROL PORT CONNECTOR
When controlling the computer with
the Remote Control of this projector,
connect the mouse port of your
personal computer to this terminal.
(Refer to P13.)
AUDIO OUTPUT JACK (STEREO)
COMPUTER INPUT TERMINAL
Connect an external audio
amplifier to this terminal.
(Refer to P12, 13.)
Connect the computer output to
this terminal.
(Refer to P13.)
COMPUTER INPUT TERMINAL
CONTROL PORT CONNECTOR
Terminal : HDB15-PIN
Terminal : DIN 8-PIN
Connect the display output terminal of the computer to
COMPUTER INPUT terminal of this projector with the
VGA Cable (supplied). When connecting the
Macintosh computer, the MAC Adapter (not supplied)
is required.
Connect control port (PS/2, Serial or ADB port) on your
computer to this terminal with the Control Cable (the Control
Cable for PS/2 port is supplied).
Pin Configuration
Pin Configuration
8
7
6
2
1
5
4
3
5
4
3
10
9
8
7
6
2
1
15
14
13
12
11
PS/2
-----
CLK
DATA
GND
-----
-----
GND
-----
Serial
R X D
-----
-----
GND
RTS
T X D
GND
GND
ADB
-----
ADB
-----
GND
-----
-----
1
2
3
4
5
6
7
8
Red Input
Green Input
Blue Input
Sense 2
9
No Connect
1
2
3
4
5
6
7
8
10 Ground (Vert.sync.)
11
12
Sense 0
Sense 1
Horiz. sync.
Vert. sync.
Reserved
Ground (Horiz.sync.) 13
Ground (Red)
Ground (Green) 15
Ground (Blue)
14
-----
GND
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING THE PROJECTOR
CONNECTING TO THE VIDEO EQUIPMENT
Cables used for connection (● = Cables are not supplied with this projector.)
• Video Cable (RCA x 1 or RCA x 3) ●
• S-VIDEO Cable ●
• Audio Cable (RCA x 2- Mini Plug x 1 (stereo) or Mini Plug (stereo)) ●
Video Source (example)
Video Cassette Recorder
Component video output equipment.
(such as DVD player or
Video Disc Player
high-definition TV source.)
Composite
Video Output
Component
Video Output
S-VIDEO Output
Audio Output
Y
Pb/Cb Pr/Cr
R
L
S-VIDEO
Audio
Cable ●
Cable ●
Use any of VIDEO jack Y-Pb/Cb-Pr/Cr
jacks or S-VIDEO jack.
Video Cables ●
• When both VIDEO jack and S-
VIDEO jack are connected, the S-
VIDEO jack has priority over the
VIDEO jack.
(stereo)
• When both Y-Pb/Cb-Pr/Cr jacks and
S-VIDEO jack are connected, the Y-
Pb/Cb-Pr/Cr jacks has priority over
the S-VIDEO jack.
Y-Pb/Cb-Pr/Cr
S-VIDEO
VIDEO
S –VIDEO
Y
–
Pb/Cb – Pr/Cr
VIDEO
AUDIO OUT
AV
RESET
COMPUTER
AUDIO OUT
AUDI
IN
CONTROL PORT
AV AUDIO IN
COMPUTER IN
Terminals
of the Projector
Audio Cable
(Stereo) ●
Audio Input
External Audio Equipment
Audio Speaker (stereo)
NOTE :
When connecting the cable, the power cords of
both the projector and the external equipment
should be disconnected from AC outlet. Turn the
projector and peripheral equipment on before the
computer is switched on.
Audio Amplifier
12
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING THE PROJECTOR
CONNECTING TO THE COMPUTER
Cables used for connection (● = Cables are not supplied with this projector.)
• VGA CABLE (HDB 15 pin)
NOTE :
• CONTROL CABLE FOR PS/2 PORT
When connecting the cable, the power cords of
• CONTROL CABLE FOR SERIAL PORT, or ADB PORT ●
• MAC ADAPTER (When connecting to Macintosh computer)
• AUDIO CABLE (Mini Plug (stereo)) ●
both the projector and the external equipment
should be disconnected from AC outlet. Turn the
projector and peripheral equipment on before the
computer is switched on.
●
IBM-compatible computers or Macintosh computers (VGA / SVGA / XGA / SXGA)
Desktop type
Laptop type
Monitor Output
Serial port PS/2 port ADB port
Audio Output
MAC Adapter ●
Set the slide
switches following
the chart below.
Audio Cable
(stereo) ●
Control Cable
for Serial Port ●
Control Cable
for ADB Port ●
Control Cable
for PS/2 Port
Terminal
Terminal
Terminal
VGA Cable
Use one of these Control
Cables corresponding
with the terminal of your
computer.
Terminals of the Projector
VIDEO
S –VIDEO
Y
–
Pb/Cb – Pr/Cr
AUDIO OUT
AV
RESET
COMPUTER
COMPUTER AUDIO IN
AUDIO
IN
AUDIO OUT
CONTROL PORT
COMPUTER IN
CONTROL PORT
COMPUTER IN
Audio Cable
(stereo) ●
● MAC ADAPTER (Not supplied)
Set the switches as shown in the table below depending on the
RESOLUTION MODE that you want to use before you turn-on the
projector and computer.
Audio Input
Audio Speaker
1
2
3
4
5
6
Audio Amplifier
(stereo)
ON
13" MODE (640 x 480)
ON
ON OFF OFF OFF OFF
ON
DIP
16" MODE (832 x 624) OFF ON OFF ON OFF OFF
1
2
3
4
5
6
19" MODE (1024 x 768) OFF ON
21" MODE (1152 x 870) ON ON
ON OFF OFF OFF
ON ON OFF OFF
OFF
13
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
OPERATION OF THE REMOTE CONTROL
Left Side
POWER ON-OFF BUTTON
Used to turn the projector on
or off. (P19)
ON-OFF
KEYSTONE D.ZOOM VOLUME
COMPUTER BUTTON
Used to select COMPUTER
input source. (P22)
MUTE
MENU
COMPUTER
VIDEO
VIDEO BUTTON
Used to select VIDEO
source. (P29)
MENU BUTTON
Used to select MENU
operation. (P17, 18)
RIGHT CLICK BUTTON
Used to compress the image
in DIGITAL ZOOM mode.
(P28)
It is also used as a PC mouse
in Wireless Mouse Operation.
(P34)
SELECT BUTTON
Used to execute the item
selected or to expand the
image in DIGITAL ZOOM
mode. (P28)
ALL-OFF SWITCH
P-TIMER
When using the Remote Control
Unit, turn this switch to “ON.” And
turn it to “ALL OFF” when it is not
used.
It is also used as a PC
mouse in Wireless Mouse
Operation. (P34)
POINT BUTTON
NO SHOW
FREEZE
Used to move the pointer on
the MENU, to adjust the item,
or to pan the image in DIGITAL
ZOOM mode. (P28)
It is also used as a PC mouse
in Wireless Mouse Operation.
(P34)
AUTO IMAGE
NORMAL
P-TIMER BUTTON
Used to operate P-TIMER
function. (P21)
● When pressing the center of this
button, it works as the SELECT
button.
Operating Range
Point the remote control toward the projector (the Remote
Receiver) whenever pressing the buttons. Maximum operating
range for the remote control is about 16.4’ (5m) and 60° in front
of the projector.
60°
16.4’
(5 m)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
ON-OFF
KEYSTONE BUTTON
Used to correct the
keystone distortion.
(P20, 28, 30)
VOLUME BUTTON
Used to adjust volume.
(P21)
KEYSTONE D.ZOOM VOLUME
D.ZOOM BUTTON
MUTE
MENU
COMPUTER
VIDEO
Used to select DIGITAL
ZOOM mode and resize
the image. (P28)
MUTE BUTTON
Used to mute sound.(P21)
P-TIMER
NO SHOW BUTTON
FREEZE BUTTON
Used to turn the picture
into black image. (P21)
Used to freeze the picture.
(P21)
NO SHOW
FREEZE
AUTO IMAGE
NORMAL
AUTO IMAGE BUTTON
NORMAL BUTTON
Use to operate AUTO
IMAGE function. (P27)
Used to reset to normal
picture adjustments preset
by the factory. (P26, 31)
Remote Control Batteries Installation
Remove the battery
compartment lid.
Slide the batteries into the
compartment.
Replace the compartment
lid.
1
2
3
Press the lid down-
ward and slide it.
Two AA size batteries
For correct polarity (+
and –), be sure the
battery terminals are in
contact with the pins in
the compartment.
To insure safe operation, please observe the following precautions :
● Use (2) AA, UM3 or R06 type alkaline batteries.
● Replace two batteries at the same time.
● Do not use a new battery with a used battery.
● Avoid contact with water or liquid.
● Do not expose the Remote Control Unit to moisture, or heat.
● Do not drop the remote control unit.
● If batteries have leaked on the remote control, carefully wipe the case clean and load new batteries.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
TOP CONTROLS AND INDICATORS
MENU BUTTON
POINT BUTTONS
WARNING TEMP. INDICATOR
READY INDICATOR
Used to open or close Used to select an item or This indicator flashes red This indicator lights
the MENU operation. adjust the value in the MENU. when internal projector green when the projector
(P17, 18)
It is also used to pan the temperature is too high. is ready to be turned on.
image in DIGITAL ZOOM (P35)
mode. (P28)
And it flashes green in
Power Management
mode. (P33)
POWER ON–OFF BUTTON
Used to turn the projector
on or off. (P19)
TELE
LAMP
REPLACE
WARNING
TEMP.
READY
LAMP
ON–OFF
MENU
MODE
NORMAL
NORMAL BUTTON
SELECT BUTTON
LAMP REPLACE INDICATOR
LAMP INDICATOR
Used to reset to normal
picture adjustment preset
by factory. (P26, 31)
Used to execute the item This indicator turns to This indicator is dim
selected. It is also used yellow when the life of the when the projector is
to expand the image in projection lamp draws to turned on. And bright
DIGITAL ZOOM mode. an end. (P36)
(P28)
when the projector is in
stand-by mode.
MODE BUTTON
Used to select input source
either Computer or Video.
(P22, 29)
16
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
OPERATING ON-SCREEN MENU
HOW TO OPERATE ON-SCREEN MENU
You can control and adjust this projector through the ON-
WIRELESS REMOTE CONTROL
SCREEN MENU. Refer to the following pages to
operate each adjustment in the ON-SCREEN MENU.
POINT BUTTON
Used to move the
Pointer UP/ DOWN/
RIGHT/ LEFT.
1 MOVING THE POINTER
Move the pointer (see the NOTE below) by pressing POINT
button(s) on the TOP CONTROL or the REMOTE CONTROL.
SELECT BUTTON
Used to select the item.
2 SELECT THE ITEM
TOP CONTROL
Select the item by pressing SELECT button.
SELECT BUTTON
Used to select the item.
NOTE : Pointer is the icon on the ON-SCREEN Menu to select
the item. See the figures on the section "FLOW OF
ON-SCREEN MENU" below.
POINT BUTTONS
Used to move the
Pointer UP/ DOWN/
RIGHT/ LEFT.
FLOW OF ON-SCREEN MENU
MENU BAR
Display ON-SCREEN MENU
Press MENU button to display the ON-SCREEN MENU
(MENU BAR). The red frame is the POINTER.
1
SELECT
BUTTON
ITEM ICON
POINTER
(red frame)
Select the Item
Move the POINTER (red frame) to the ITEM ICON that
you want to select by pressing POINT RIGHT/ LEFT
buttons.
2
Select the ITEM by pressing SELECT button. The dialog
box of the ITEM appears.
POINTER
(red frame)
3
Control and adjust through ON-SCREEN MENU
MENU
Move the POINTER downward by pressing POINT
DOWN button. (The shape of the POINTER becomes an
arrow.)
4
POINT
DOWN
BUTTON
Move the POINTER to the ITEM that you want to adjust
5
and adjust the ITEM by pressing SELECT button.
Refer to the following pages for details of respective
adjustments.
POINTER
17
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
MENU BAR
MENU BAR IN COMPUTER MODE
Press MENU BUTTON while in Computer mode.
MODE MENU
AUTO IMAGE MENU
PC ADJUST MENU
SETTING MENU
LANGUAGE MENU
Used to select
the Computer
input mode.
Used to adjust Fine
sync, Total dots,
and Picture Position
automatically.
Used to adjust the
parameters to
match with the input
signal format.
Used to adjust Volume,
set the Display Menu and
reset Lamp Replacement
Monitor Timer.
Used to select
the language
used in the
Menu.
(Refer to P22)
(Refer to P27)
(Refer to P24, 25)
(Refer to P32, 33)
(Refer to P33)
SYSTEM MENU
IMAGE MENU
Used to adjust the
POSITION MENU
SCREEN MENU
Used to select a
computer
system.
Used to adjust
the position of
the image.
Used to adjust the
size of the image or
to correct the
Keystone distortion.
(Refer to P28)
[Fine sync
computer image.
/ Total dots / White Balance /
Contrast / Brightness /
Gamma]
(Refer to P22)
(Refer to P27)
(Refer to P26)
MENU BAR IN VIDEO MODE
MODE MENU
Press MENU BUTTON while in Video mode.
IMAGE MENU
Used to adjust the
Color /
Tint / White Balance /
Contrast / Brightness/
picture image. [
Used to select
the Video input.
(Refer to P29)
Same function as the
Computer Mode.
Sharpness / Gamma
(Refer to P31)
]
SYSTEM MENU
VIDEO SOURCE MENU
SCREEN MENU
Used to select a
color system of the
selected video
source.
Used to select a
video source among
Used to set the size
of the image either
Regular or Wide,
or to correct the
Keystone distortion.
(Refer to P30)
Video, S-Video, and Y,
[
Pb/Cb, Pr/Cr
].
(Refer to P29)
(Refer to P30)
18
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
TURNING ON / OFF THE PROJECTOR
TURNING ON THE PROJECTOR
Complete the peripheral connections (with Computer, VCR, etc.)
before turning on the projector. (Refer to "CONNECTING TO
THE PROJECTOR" on Pages 11~13 for connecting that
equipment.)
1
Connect the projector's AC Power Cord into a wall outlet. The
LAMP indicator lights RED, and the READY indicator lights
GREEN.
2
3
30
Press the power ON-OFF button on the Remote Control Unit or
on the Top Control to ON. The LAMP indicator dims, and the
Cooling Fans start to operate. The Preparation Display appears
on the screen and the count-down starts. The signal from the
source appears after 30 seconds.
The Preparation Display disappears after 30 seconds.
TURNING OFF THE PROJECTOR
Press the power ON-OFF button on the Remote Control Unit or
on the Top Control, and the message "Power off?" appears on
the screen.
1
2
Power off?
Press the power ON-OFF button again to turn off the projector.
The LAMP indicator lights bright and the READY indicator turns
off. The Cooling Fans operate for 90 seconds after the projector
is turned off. (During this "Cooling Down" period, this appliance
cannot be turned on.)
The message disappears after 4 seconds.
When the projector has cooled down, the READY indicator turns
to green again and you can turn the projector on. After cooling
down completely, disconnect the AC power cord.
3
TO MAINTAIN THE LIFE OF THE LAMP, ONCE YOU
TURN THE PROJECTOR ON, WAIT AT LEAST 5
MINUTES BEFORE TURNING IT OFF.
When the Power Management function is ON, the Projector detects the signal interruption and turns the Projection Lamp
off automatically. Refer to “Power Management” on page 33.
When the TEMPERATURE WARNING indicator flashes red, the projector is automatically turned off. Wait at least 5
minutes before turning the projector on again.
When the TEMPERATURE WARNING indicator continues to flash, follow procedures below:
1. Press the power ON-OFF button to turn off the projector and disconnect the AC power cord from the AC outlet.
2. Check the air filters for dust accumulation.
3. Clean the Air Filter. (See "AIR FILTER CARE AND CLEANING" section on page 35.)
4. Press the power ON-OFF button to turn it on.
If the TEMPERATURE WARNING indicator still continues to flash, call Boxlight at 1-800-762-5757 or 360-779-7901.
NOTE: The Cooling Fan may work for cooling while the projector is turned off. When the Cooling Fan
is working, TEMPERATURE WARNING INDICATOR flashes red.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
ADJUSTING THE IMAGE
ZOOM ADJUSTMENT
Turn the ZOOM RING to adjust the projected picture size. Turn
the ring to “WIDE” direction to make the image larger, and turn
to “TELE” direction to make the image smaller.
MIN.
MAX.
ZOOM RING
FOCUS ADJUSTMENT
Turn the FOCUS RING to adjust the projected picture focus.
FOCUS RING
KEYSTONE ADJUSTMENT
If the picture has keystone distortion, correct image with KEYSTONE adjustment.
Press the KEYSTONE ●/● button on the Remote Control Unit
or select the Keystone on the SCREEN menu. (Refer to page
28, 30.) The message “Keystone” is displayed.
1
Keystone
Correct the Keystone distortion by pressing the KEYSTONE
●/● button or the POINT UP/DOWN button(s). Press the
KEYSTONE ● button or the POINT UP button to reduce the
upper part or the image, and press the KEYSTONE ● button or
the POINT DOWN button to reduce the lower part.
2
The message disappears after 4 seconds.
Reduce the upper width with the KEY STONE ●
button or the POINT UP button.
Reduce the lower width with the KEY STONE ●
button or the POINT DOWN button.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
NO SHOW FUNCTION
Press the NO SHOW button on the Remote Control Unit to
No show
black out the image. This function is cancelled when the NO
SHOW button is pressed again or any other function button is
pressed.
The message disappears after 4 seconds.
PICTURE FREEZE FUNCTION
Press the FREEZE button on the Remote Control Unit to freeze the picture on-screen. This function is
cancelled when the FREEZE button is pressed again or any other function button is pressed.
P-TIMER FUNCTION
Press the P-TIMER button on the Remote Control unit. The
timer display “00 : 00” appears on the screen and the timer
starts to count the time (00 : 00 ~ 59 : 59).
To stop the P-TIMER, press the P-TIMER button. And then,
press the P-TIMER button again to cancel the P-TIMER
function.
SOUND ADJUSTMENT
Indicates the level of the volume.
SOUND VOLUME ADJUSTMENT
Press the VOLUME (+/–) button on the Remote Control Unit to
adjust the volume. The Volume dialog box appears on the
screen for a few seconds.The VOLUME (+) button increases
the volume, and the VOLUME (–) button decreases the
volume.
The sound volume can be adjusted through the ON-SCREEN
MENU. (Refer to page 32.)
Press the MUTE button to turn
the Mute function On or Off.
The display disappears after 4 seconds.
SOUND MUTE ADJUSTMENT
Press the MUTE button on the Remote Control Unit to mute the
sound. To restore the sound to its previous level, press the
MUTE button again or press the VOLUME (+/–) button.
The sound mute can be set through the ON-SCREEN MENU.
(Refer to page 32.)
21
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER MODE
SELECTING COMPUTER MODE
DIRECT OPERATION
MODE button
COMPUTER
Select COMPUTER mode by pressing the MODE button on the
Top Control or the COMPUTER button on the Remote Control
Unit.
VIDEO
MENU OPERATION
Press the MENU button and the ON-SCREEN MENU will
appear.
Computer
Press the POINT LEFT/RIGHT buttons to select
and press the SELECT button.
CURRENT MODE DISPLAY
When selecting the Computer Mode, the Current Mode display
appears. It shows the information of the computer of the mode
selected.
Providing the information of the computer detected
by the projector.
SELECTING COMPUTER SYSTEM
AUTOMATIC MULTI-SCAN SYSTEM
This projector automatically tunes to most different types of
computers based on VGA, SVGA, XGA or SXGA (refer to
“COMPATIBLE COMPUTER SPECIFICATION” on page 23).
When selecting Computer, this projector automatically tunes to
the incoming signal and projects the proper image without any
special settings. (Setting of the Computer System may be
required when connecting some computers.)
SYSTEM BOX
Displays the SYSTEM
being selected.
Note : The projector may display one of the following messages.
The projector cannot discriminate or detect the input
signal from the computer. Adjust and set the
computer system manually. (Refer to page 24.)
Go to PC adj.
There is no signal input from the computer. Make
sure the connection of the computer and the
projector is set correctly.
No signal
(Refer to TROUBLESHOOTING on page 37.)
The system being selected.
SELECT COMPUTER SYSTEM MANUALLY
To set the Computer system manually, select the mode on the
ON-SCREEN MENU.
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select
SYSTEM and press the SELECT button. Another dialog box
COMPUTER SYSTEM Menu will appear.
1
The systems on
these dialog boxes
can be selected.
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to the system that you want to set, and
2
then press
SELECT button.
Closes the SYSTEM
Menu.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER MODE
COMPATIBLE COMPUTER SPECIFICATIONS
Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned and
less than 140 MHz of Dot Clock.
ON-SCREEN
DISPLAY
ON-SCREEN
DISPLAY
H-Freq.
(kHz)
V-Freq.
(Hz)
H-Freq.
(kHz)
V-Freq.
(Hz)
RESOLUTION
RESOLUTION
VGA 1
VGA 2
640 x 480
720 x 400
640 x 400
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
31.47
31.47
31.47
37.86
37.86
37.50
43.269
34.97
35.00
15.625
15.734
35.156
37.88
46.875
53.674
48.08
37.90
34.50
38.00
38.60
32.70
38.00
49.72
48.36
68.677
60.023
56.476
60.31
48.50
44.00
63.48
36.00
59.88
70.09
70.09
74.38
72.81
75.00
85.00
66.60
66.67
XGA 10
XGA 11
XGA 12
XGA 13
XGA 14
XGA 15
MAC 19
MAC 21
SXGA 1
SXGA 2
SXGA 3
SXGA 4
SXGA 5
SXGA 6
SXGA 7
SXGA 8
SXGA 9
SXGA 10
SXGA 11
SXGA 12
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1152 x 870
1152 x 864
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 960
1152 x 900
1152 x 900
62.04
61.00
35.522
46.90
47.00
58.03
60.24
68.68
64.20
62.50
63.90
63.34
63.74
71.69
81.13
63.98
79.976
60.00
61.20
71.40
50.00
50.00
63.37
76.97
61.85
46.43
63.79
75.00
80.00
45.00
33.75
33.75
77.07
75.70
86.96
(Interlace)
VGA 3
VGA 4
58.20
58.30
72.00
75.08
75.06
70.40
58.60
60.00
59.98
60.01
67.19
76.107
60.02
75.025
60.00
65.20
75.60
VGA 5
VGA 6
VGA 7
MAC LC13
MAC 13
RGB
640 x 480
50
––––––––
(Interlace)
60
––––––––
RGB
(Interlace)
SVGA 1
SVGA 2
SVGA 3
SVGA 4
SVGA 5
SVGA 6
SVGA 7
SVGA 8
SVGA 9
SVGA 10
SVGA 11
MAC 16
XGA 1
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
56.25
60.32
75.00
85.06
72.19
61.03
55.38
60.51
60.31
51.09
60.51
74.55
60.00
84.997
75.03
70.07
74.92
60.02
54.58
79.35
86.00
(Interlace)
94.00
(Interlace)
SXGA 13 1280 x 1024
SXGA 14 1280 x 1024
SXGA 15 1280 x 1024
SXGA 16 1280 x 1024
60.01
72.00
66.00
XGA 2
SXGA 17
1152 x 900
86.70
(Interlace)
XGA 3
SXGA 18 1280 x 1024
SXGA 19 1280 x 1024
XGA 4
60.18
75.08
75.08
60.00
60.00
(Interlace)
60.00
(Interlace)
XGA 5
MAC
1280 x 960
XGA 6
MAC
1280 x 1024
––––––––
XGA 7
HDTV720p
HDTV1035i
HDTV1080i
––––––––
––––––––
XGA 8
87.17
(Interlace)
XGA 9
NOTE : Specifications are subject to change without notice.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER MODE
PC ADJUSTMENT
This Projector can automatically tune to the display signals from most personal computers currently distributed.
However, some computers employ special signal formats which are different from the standard ones and may
not be tuned by the Multi-Scan system of this projector. If this happens, the projector cannot reproduce a proper
image and the image may be recognized as a flickering picture, a non-synchronized picture, a non-centered
picture or a skewed picture.
This projector has a PC ADJUSTMENT function, to enable you to precisely adjust several parameters to match
with those special signal formats. This projector has five independent memory areas to memorize those
parameters manually adjusted. This enables you to recall the setting for a specific computer whenever you use
it.
Note : This PC ADJUSTMENT function cannot be operated when “RGB,” “HDTV1035i” or “HDTV1080i” is selected on the
SYSTEM MENU (P22 and 23).
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT RIGHT/LEFT buttons to select PC
1
ADJUST
and press the SELECT button. Another dialog box
“Where to reserve” Menu will appear.
In this dialog box, you can store the parameter into the area from
“Mode 1” to “Mode 5.” When memorizing the new computer
parameter, select the Mode with the message “Free” by pressing
the POINT UP/DOWN buttons and the SELECT button. To
change the parameters of the Mode previously set, select the
Mode with “Stored.”
2
3
This Mode has
parameters being
stored.
The Vacant Mode.
Manual set Computer
Mode (1 to 5).
When the Mode is selected, Parameter adjustment dialog box
appears. Move the arrow to the item that you want to change by
pressing the POINT UP/DOWN buttons, and adjust each item to
match with your computer. To change the value, press either
the POINT RIGHT / LEFT button.
Closes the PC
ADJUSTMENT Menu.
Refer to the next page for adjusting each item.
Move the arrow to “Stored” and press the SELECT button. The
parameter is memorized in the selected Mode.
4
5
To activate the Mode manually adjusted in this PC
ADJUSTMENT Menu, select the Mode at the SYSTEM SELECT
Menu. (Refer to page 22.)
Press the POINT
RIGHT/LEFT button(s)
to adjust the value.
Press the SELECT
button to set Full
screen function on/off.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER MODE
Total lines
The number of the total vertical lines. Adjust the number to match
the image of your personal computer.
Total dots
The number of the total dots in one horizontal period. Adjust the
number to match the image of your personal computer.
Horizontal / Vertical
Adjustment of the horizontal or vertical picture position. When the
image is not centered on the screen, adjust each of those items.
Press the
SELECT button
to select the
typical resolution
of the image.
Clamp
Adjustment of the clamp level. When the image has a dark bar(s),
try this adjustment.
Display area
Adjustment of the area displayed with this projector. Select the
resolution at the Display area dialog box, or adjust the number at the
column of “H” or “V” to match the resolution of the image.
Full Screen
Set “On” to resize the image with 4 x 3 aspect ratio to fit the screen.
Each of the keys operates as follow.
Reset
Recalls the parameter data that was previously
adjusted.
Mode free
Stored
Quit
Clears the parameter data previously set.
Stores the parameters in the memory.
Closes the PC ADJUST Menu.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER MODE
PICTURE IMAGE ADJUSTMENTS
ADJUST PICTURE IMAGE MANUALLY
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select IMAGE
and press the SELECT button. Another dialog box
PICTURE IMAGE ADJUSTMENT Menu will appear.
1
2
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to the item that you want to change by
pressing the POINT UP/DOWN buttons. To change the value,
press either the POINT RIGHT button or the POINT LEFT
button.
Fine sync
Adjust the picture as necessary to eliminate flicker from the display.
(From 0 to 255.)
Total dots
The number of the total dots in one horizontal period. Adjust the
number to match your PC image.
White balance (Red / Green / Blue)
Move the arrow to the color that you want to adjust. Press POINT
LEFT button to lighten the color and press POINT RIGHT button to
deepen the color. (From 0 to 63.)
Contrast
Move the arrow to the item
and press POINT RIGHT /
LEFT button.
Closes the PICTURE
IMAGE ADJUSTMENT
Menu.
Press POINT LEFT button to decrease contrast, and press POINT
RIGHT button to increase contrast. (From 0 to 63.)
Brightness
NOTE : The Fine sync and the Total dots cannot
be adjusted when “RGB,” “HDTV1035i” or
“HDTV1080i” is selected on the SYSTEM
MENU (P22 and 23).
Press POINT LEFT button to adjust the image darker, and press
POINT RIGHT button to adjust brighter. (From 0 to 63.)
Gamma
Press either POINT LEFT button or POINT RIGHT button to obtain
better balance of contrast. (From 0 to 16.)
Each of the keys operates as follow.
Reset
Stored
Quit
Recalls the data previously adjusted.
Stores the adjusted data in the memory.
Closes the PICTURE IMAGE ADJUSTMENT Menu.
NORMAL FUNCTION
The normal picture level is preset on this projector at the
factory and can be restored anytime you press the NORMAL
button (located on the Top Control or on the Remote Control
Unit). The “Normal” display will be displayed on the screen for
a few seconds.
Normal
26
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER MODE
AUTO IMAGE FUNCTION
The Auto Image function is provided to automatically adjust
Fine sync, Total dots, and Picture Position for most computers.
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select AUTO
1
IMAGE
and press the SELECT button.
Another dialog box AUTO IMAGE Menu will appear.
Move the arrow to an item that you want to adjust by pressing
the POINT UP/DOWN button. Change the setting On or Off by
pressing the SELECT button.
2
Fine sync
Adjust the picture as necessary to eliminate flicker from the display.
This item can be adjusted manually. (Refer to page 26.)
Total dots
The number of the total dots in one horizontal period. This item can
be adjusted manually. (Refer to page 26.)
Starts the adjustment
on the item set to "On".
Position
Move the arrow to
the item and then
press the SELECT
button.
Adjustment of the position of the image. This item can be adjusted
manually. (Refer to page 27.)
Closes the AUTO IMAGE
FUNCTION Menu.
Move the arrow to “Go!” and press the SELECT button to start
the Auto Image function.
This adjustment can be executed by pressing AUTO IMAGE
button on the Remote Control Unit.
3
Stored
Stores the On/Off setting of each item.
Starts the Auto Image Function.
Go!
Quit
Closes the AUTO IMAGE FUNCTION Menu.
NOTE : The Fine sync and the Total dots cannot be fully adjusted when “RGB,” “HDTV1035i” or “HDTV1080i” is selected on
the SYSTEM MENU (P22 and 23).
The Fine sync, Total dots, and Picture Position of some computers may not be fully adjusted with the Auto Image
Function. In that case, manual adjustment is required to make fine image. (Refer to page 26 to adjust "Fine sync"
or "Total dots" and page 27 to adjust Picture Position.)
PICTURE POSITION ADJUSTMENT
The position of the image can be adjusted vertically and horizontally through PICTURE POSITION
ADJUSTMENT.
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select
1
POSITION
and press the SELECT button. The PICTURE
POSITION dialog box will appear.
PICTURE POSITION
dialog box
Move the image by pressing the POINT UP / DOWN / RIGHT /
LEFT buttons.
2
Press the POINT UP
/
To cancel PICTURE POSITION ADJUSTMENT, press any
button except POINT buttons. To return to the position
previously set, press NORMAL button.
DOWN / RIGHT / LEFT
buttons to move the image
27
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER MODE
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen resize function, which enables you to display the desirable image size.
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select
1
SCREEN
and press the SELECT button. Another dialog
box PICTURE SCREEN Menu will appear.
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to the function that you want to select
and then press SELECT button.
2
True
To make the image into its original size select True in the dialog box.
When the original image size is larger than the screen size (1024 x
768), this projector enters Digital Zoom mode automatically.
Move the arrow to the
function and press the
SELECT button.
Keystone
NOTE : The True and the Digital Zoom cannot be
operated when “RGB,” “HDTV1035i” or
“HDTV1080i” is selected on the SYSTEM
MENU (P22 and 23).
When the image is distorted vertically, select Keystone in the dialog
box. The ON-SCREEN menu and SCREEN ADJUST menu
disappears and the message “Keystone” is displayed. Correct the
Keystone distortion by pressing the KEYSTONE ●/● button or the
POINT UP/DOWN button(s). Refer to KEYSTONE ADJUSTMENT
on page 20.
Digital Zoom
To adjust the image size or pan the image, select Digital zoom in the
dialog box. The ON-SCREEN menu and SCREEN ADJUST menu
disappears and the message “D. Zoom” is displayed.
This projector also enters Digital Zoom mode by pressing the
D.ZOOM ●/● button on the Remote Control Unit.
Refer to the following for operation.
Expand function
To expand the image size, press the D.ZOOM ● button or the
SELECT button. The image is magnified by degrees.
Compress function
To compress the image size, press the D.ZOOM ● button or the
RIGHT CLICK button. The size of image is reduced by degrees.
Panning function
To pan the image, press the POINT UP/DOWN/LEFT/RIGHT buttons.
Panning function can work only when the image is larger than the
screen size.
To cancel Digital Zoom mode, press any button except D.ZOOM
●/●, SELECT, RIGHT CLICK, or POINT button. To adjust the image
to 1024 x 768, press NORMAL button.
● This projector cannot display any resolution higher than 1280 X
1024. If your computer’s screen resolution is higher than 1280 X
1024, reset the resolution to the lower before connecting the
projector.
● The image data in other than XGA (1024 x 768) is modified to fit
the screen size in the initial mode.
● The normal "Panning Operation" may not function properly if the
computer system prepared with the "PC Adjust" is used.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO MODE
SELECTING VIDEO MODE
DIRECT OPERATION
MODE button
COMPUTER
Select VIDEO mode by pressing the MODE button on the Top
Control or the VIDEO button on the Remote Control Unit.
VIDEO
MENU OPERATION
Press the MENU button and the ON-SCREEN MENU will
appear.
Press the POINT LEFT/RIGHT buttons to select Video
and press the SELECT button.
SELECTING VIDEO SOURCE
This projector automatically detects the signal from the VIDEO
INPUT JACK(s) or the S-VIDEO INPUT JACK. When those
jacks are connected at the same time, select the type of Video
source in VIDEO SOURCE Menu.
This box indicates the Video
source being selected.
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select VIDEO
SOURCE and press the SELECT button. Another dialog box
VIDEO SOURCE Menu will appear.
1
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to the source that you want to select,
2
and then press the
SELECT button.
Auto
The projector automatically detects the incoming Video source, and
adjusts itself to optimize its performance.
• When both VIDEO jack and S-VIDEO jack are connected, the S-
VIDEO jack has priority over the VIDEO jack.
• When both Y-Pb/Cb-Pr/Cr jacks and S-VIDEO jack are connected,
the Y-Pb/Cb-Pr/Cr jacks have priority over the S-VIDEO jack.
Video / S-Video / Y, Pb/Cb, Pr/Cr
When the VIDEO INPUT JACK(s) and the S-VIDEO INPUT JACK
are connected at the same time, or if the projector cannot chose the
proper video source, it is necessary to select a specific video source
among Video, S-Video and Y, Pb/Cb, Pr/Cr.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO MODE
SELECTING COLOR SYSTEM
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select
SYSTEM and press the SELECT button. Another dialog box
VIDEO SYSTEM Menu will appear.
1
2
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to "Auto", and then press the
SELECT
button.
When the Video signal is from the VIDEO or the S-VIDEO JACK
This box indicates the
system being selected.
Auto
The projector automatically detects the incoming Video system, and
adjusts itself to optimize its performance.
When the Video System is PAL-M or PAL-N, select the system
manually.
PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N
If the projector cannot reproduce the proper video image, it is
necessary to select a specific broadcast signal format among PAL,
SECAM, NTSC, NTSC 4.43, PAL-M, and PAL-N.
Move the arrow to
the Mode and press
the SELECT button.
When the Video signal is from the Y, Pb/Cb, Pr/Cr JACKS
This box indicates the
system being selected.
Auto
The projector automatically detects the incoming Video signal, and
adjusts itself to optimize its performance.
COMPONENT VIDEO SIGNAL FORMAT
If the projector cannot reproduce the proper video image, it is
necessary to select a specific component video signal format among
480i, 575i, 480p, 575p, 720p, 1035i and 1080i.
Move the arrow to
the Mode and press
the SELECT button.
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen resize function, which enables you to display the desirable image size.
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select
1
SCREEN
and press the SELECT button. Another dialog
box PICTURE SCREEN ADJUSTMENT DISPLAY will appear.
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to the screen size that you want to set,
2
and then press the
SELECT button.
Regular
Move the pointer to the function and
press the SELECT button.
Normal Video Image size with 4 x 3 aspect ratio.
Wide
NOTE : The Regular and the Wide cannot be
operated when “720p,” “1035i” or
“1080i” is selected on SYSTEM MENU
(above).
Resizes the image for wide screen size with 16 x 9 aspect ratio.
Keystone
When the image is distorted vertically, select Keystone in the dialog
box. Correct the Keystone distortion by pressing KEYSTONE ●/●
button or POINT UP/DOWN button(s). Refer to KEYSTONE
ADJUSTMENT on page 20.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO MODE
PICTURE IMAGE ADJUSTMENT
ADJUSTING THE PICTURE IMAGE
Press the MENU button and the ON-SCREEN MENU will
1
2
appear. Press the POINT LEFT/RIGHT buttons to select IMAGE
and press the SELECT button. Another dialog box
PICTURE IMAGE ADJUSTMENT Menu will appear.
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to the item that you want to adjust by
pressing the POINT UP/DOWN buttons. To change the value,
press either the POINT RIGHT button or the POINT LEFT
button.
Color
Press POINT LEFT button to lighten the image, and press POINT
RIGHT button to deepen the image. (From 0 to 63.)
Tint
Press POINT LEFT button to increase purple, and press POINT
RIGHT button to increase green. (From 0 to 63.)
White balance (Red / Green / Blue)
Move the arrow to the color that you want to adjust. Press POINT
LEFT button to lighten the color, and press POINT RIGHT button to
deepen the color. (From 0 to 63.)
Move the arrow to the item
and press POINT RIGHT /
LEFT button.
Contrast
Closes the PICTURE
IMAGE ADJUSTMENT
Menu.
Press POINT LEFT button to decrease contrast, and press POINT
RIGHT button to increase contrast. (From 0 to 63.)
Brightness
Press POINT LEFT button to darken the image, and press POINT
RIGHT button to brighten the image. (From 0 to 63.)
Sharpness
Press POINT LEFT button to soften the image, and press POINT
RIGHT button to sharpen the image. (From 0 to 15.)
Gamma
Press either POINT LEFT button or POINT RIGHT button to obtain
better balance of contrast. (From 0 to 16.)
Each of the keys operates as follow.
Reset
Stored
Quit
Recalls the data previously adjusted.
Stores the data in the memory.
Closes the PICTURE IMAGE ADJUSTMENT Menu.
NORMAL FUNCTION
The normal picture level is preset on this projector at the
factory and can be restored anytime you press the NORMAL
button (located on the Top Control or on the Remote Control
Unit). The "Normal" display will be displayed on the screen for
a few seconds.
Normal
31
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING
SETTING MENU
Press the MENU button and the ON-SCREEN MENU will
appear. Press the POINT LEFT/RIGHT buttons to select
SETTING and press the SELECT button. Another dialog
box SETTING Menu will appear.
1
2
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to the item that you want to set, and
then press the
SELECT button to set it "On" or "Off" or press the
POINT LEFT/RIGHT button to adjust the value.
Indicates the level
of the volume.
Volume
Press the POINT
RIGHT / LEFT button
to adjust the volume.
Press POINT LEFT button to decrease volume, and press POINT
RIGHT button to increase the volume. (From 0 to 63.)
The sound volume can be also adjusted by pressing the VOLUME
(+/–) button on the remote control unit. (Refer to page 21)
Mute
Move the arrow to the
item and then press
the SELECT button.
Set “On” to mute the sound. To restore the sound, set “Off” or press
the MUTE button or the VOLUME (+/–) button on the remote control
unit.
The mute can be also set by pressing the MUTE button on the
remote control unit. (Refer to page 21)
Closes the Setting Menu.
Blue back
When this function is “On,” this projector will produce a blue image
instead of the video noise on the screen when the input source is
unplugged or turned off.
Display
This function decides whether to display the On-Screen Displays
(except ON-SCREEN MENU).
Set “On1” to show all the On-Screen Displays.
Set “On2” to show the On-Screen Displays except the Preparation
Display (Our Logo).
Set “Off” to set the On-Screen Displays below disappeared.
● Preparation Display (Our Logo and the Number-counting-
down Display)
● Mode Display (Computer / Video)
● Volume/Mute Displays
● Normal Display
● No show Display
● Keystone Display
● True Display
● D.Zoom Display
Ceiling function
Ceiling
When this function is “On,” the top / bottom and the left / right
reversed picture is provided to project the image from a ceiling
mounted projector.
Rear
Rear function
When this function is “On,” the left / right reversed picture is provided
to project the image to a rear projection screen.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING
Power management
This function turns the Projection Lamp off when the projector
detects signal interruption and the projector is not used for a certain
period in order to reduce power consumption and maintain the Lamp-
life. (This projector is shipped with this function ON.)
Power Management function operates to turn the Projection Lamp off
when the input signal is interrupted and the projector is not operated
over 5 minutes. This function operates as follows;
1. When the signal is interrupted, “No signal” and the counting
Time left until Lamp off.
down (5 minutes) display appears.
2. When the Projection Lamp turned off, the READY indicator
turns off. The Cooling Fans operate for 90 seconds after the
Projection Lamp is turned off. (During this "Cooling Down"
period, the Lamp cannot be turned on.)
3. When the Lamp has cooled down, the READY indicator flashes
and the Lamp can be turned on again (Power Management
mode).
In this Power Management mode, the Projection Lamp is
automatically turned on when the input signal connected or the
projector is operated with any button on the Top Control or the
Remote Control.
Lamp age
The Lamp age function is designed to reset the lamp replacement
monitor timer. When replacing the lamp, reset the lamp replacement
monitor timer by using this function. (Refer to page 36.)
SELECTING LANGUAGE
The language used in the ON-SCREEN MENU is selectable
from among English, German, French, Italian, Spanish and
Japanese.
Press the MENU button and the ON-SCREEN MENU will
appear. Press POINT LEFT/RIGHT buttons to select
LANGUAGE and press the SELECT button. Another dialog box
LANGUAGE Menu will appear.
1
Move the Pointer to the
language that you want to
set, and then press the
SELECT button.
Press the POINT DOWN button and a red-arrow icon will
appear. Move the arrow to the language that you want to set,
2
and then press the
SELECT button.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
OPERATING WIRELESS MOUSE
The Wireless Remote Control Unit is not only able to operate the projector but also usable as a wireless mouse
for most Personal Computers. The POINT buttons and the two CLICK buttons are used for the wireless mouse
operation.
The wireless mouse is available only when PC mouse pointer is displayed on the screen. When the menu or
the indicator of the projector is displayed on the screen instead of the PC mouse pointer, the wireless mouse
cannot be used.
INSTALLATION
To use the Wireless Remote Control Unit as the Wireless Mouse for a Personal Computer, installation of the
mouse driver (not supplied) is required. Make sure that the mouse driver is properly installed in your computer.
And make sure that the mouse port of the computer connected to Control Port is activated.
Connect the mouse port of your computer to the Control Port of
the projector with the Control Cable. (Refer to page 10 to 13 for
connection.)
1
Note : When the computer has no
mouse port, connect the Serial
Port of the computer to Control
Port of the projector with the
Control Cable for Serial Port.
Turn the projector on first, and then turn on your computer.
When the computer is switched on first, the Wireless Mouse may
not work properly.
2
OPERATING WIRELESS MOUSE
When controlling the pointer of the computer, operate the Wireless Mouse with POINT button, SELECT button,
and RIGHT CLICK button on the Wireless Remote Control Unit.
POINT button (Move the pointer)
POINT button
Used to move the pointer. The pointer is moved corresponding with
the direction you are pressing.
SELECT (LEFT CLICK) button
This button has the same function as the left button in a PC mouse.
RIGHT CLICK button
This button has the same function as the right button in a PC mouse.
Pressing this button does not affect any operation when in Menu
mode.
SELECT button
(left button of the
mouse)
RIGHT CLICK button
(right button of the mouse)
34
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
MAINTENANCE
TEMPERATURE WARNING INDICATOR
The TEMPERATURE WARNING Indicator flashes red when the internal temperature of the projector exceeds
the normal temperature. The Indicator stops flashing when the temperature of the projector returns to normal.
When the TEMPERATURE WARNING Indicator continues to flash, check the items listed below.
The Ventilation slots of the projector may be blocked. In such an event, reposition the projector so that the ventilation
slots are not obstructed.
1
Air filters may be clogged with dust particles. Clean the air filters by following the section AIR FILTER CARE AND
CLEANING below.
2
If the TEMPERATURE WARNING Indicator remains on after performing the above checks, the Cooling Fans or the
Internal Circuits may be malfunctioning. In that case, call Boxlight.
3
AIR FILTER CARE AND CLEANING
The Removable Air Filters prevent dust from accumulating on the surface of the Projection Lens and the
Projection Mirror. Should the Air Filters become clogged with dust particles, it will reduce the Cooling Fans'
effectiveness and may result in internal heat build up and adversely affect the life of the projector.
Clean the Air Filters following the steps below:
Turn the power off, and disconnect the AC power cord from the
AC outlet.
AIR FILTER
(Small)
AIR FILTER
(Large)
1
2
3
4
Turn the projector upside down and remove two Air Filters
(Large and Small) by pulling the latches upward.
Clean the Air Filters with brush or wash out the dust and
particles.
Replace each Air Filter properly. Make sure that the Air Filters
are fully inserted.
CAUTION
Do not operate the projector with the Air Filter removed.
Dust may accumulate on the LCD Panel and the Mirror
degrading picture quality.
Do not put small parts into the Air Intake Vents. It may
result in malfunction of the projector.
The Air Filter is a small part. Ensure that children don’t eat
or swallow it.
RECOMMENDATION
We recommend avoiding dusty/smoky environments when operating the projector. Usage in these
environments may cause poor image quality.
When using under dusty or smoky conditions, dust may accumulate on the liquid crystal panel, lens, or optical elements
inside it. This condition may degrade the quality of the projected image.
When the above symptoms are noticed contact Boxlight at 1-800-762-5757 or 360-779-7901 for cleaning.
CLEANING THE PROJECTION LENS
Follow these steps to clean the projection lens:
Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth. Avoid using an excessive amount of cleaner.
Abrasive cleaners, solvents or other harsh chemicals might scratch the lens.
1
Lightly wipe the cleaning cloth over the lens.
2
3
When the projector is not in use, replace the lens cover.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
LAMP REPLACEMENT
When the life of the Lamp of this projector draws to an end, the LAMP REPLACEMENT indicator lights yellow.
When the image becomes dark or the color of the image becomes unnatural, replacement of the Lamp is
required.
CAUTION
● For continued safety, replace with a lamp assembly of the same type.
● Allow the projector to cool for at least 45 minutes before you open the lamp cover. The inside of the projector
can become very hot.
● Do not drop the lamp assembly or touch the glass bulb! The glass can shatter and may cause injury.
Follow these steps to replace the lamp assembly.
LAMP COVER
Turn off the projector and disconnect the AC plug. Allow the
projector to cool for at least 45 minutes.
1
Remove the screw with a screwdriver and remove the Lamp
Cover.
2
Remove the two screws with a screwdriver and pull out the
Lamp Assembly by grasping the handle.
3
Replace the Lamp Assembly with a new one and tighten the two
screws. Make sure that the Lamp Assembly is set properly.
Replace the Lamp Cover and tighten the screw.
4
HANDLE
Connect the AC Power Cord to the projector and turn the
projector on.
5
Reset the Lamp Replacement Monitor Timer (refer to the section
“Lamp Replacement Monitor Timer” below).
6
NOTE : Do not reset the LAMP REPLACEMENT MONITOR
LAMP
ASSEMBLY
TIMER when the lamp is not replaced.
ORDER REPLACEMENT LAMP
Replacement Lamp can be ordered through Boxlight at 1-800-762-5757 or 360-779-7901.
● Model No. of your projector : BOXLIGHT XP-5t
● Replacement Lamp Type No. : POA-LMP31
(Service Parts No. 610 289 8422)
LAMP REPLACEMENT MONITOR TIMER
Be sure to reset the Lamp Replacement Monitor Timer when the Lamp Assembly is replaced. When the Lamp
Replacement Monitor Timer is reset, the LAMP REPLACEMENT indicator stops lighting.
Turn the projector on, and press the MENU button and the ON-SCREEN MENU will appear. Press the POINT
LEFT/RIGHT buttons to select SETTING and press the SELECT button (refer to the page 32, 33). Another dialog box
SETTING MENU will appear.
1
Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to “Lamp age,” and then press the
SELECT button. The message "Lamp replace monitor Reset?" is displayed.
2
Select [Yes] to reset the Timer.
3
Do not reset the Lamp Replacement Monitor Timer, except after the lamp is replaced.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
TROUBLESHOOTING
Before calling your dealer or service center for assistance, check the matters below once again.
1. Make sure you have connected the projector to your equipment as described in the section "CONNECTING
THE PROJECTOR" on pages 11 ~ 13.
2. Check cable connection. Verify that all computer, video and power cords are properly connected.
3. Verify that all power is switched on.
4. If the projector still does not produce an image, re-start the computer.
5. If the image sill does not appear, unplug the projector from the computer and check the computer monitor's
display. The problem may be with your graphics controller rather than with the projector. (When you
reconnect the projector, remember to turn the computer and monitor off before you power up the projector.
Power the equipment back on in order of : Projector and computer.)
6. If the problem still exists, check the following chart.
Problem:
No power.
Try these Solutions
● Plug the projector into the AC outlet.
● Be sure READY Indicator light is On.
● Wait 90 seconds after the projector is turned OFF before turning the projector back on.
NOTE : After pressing the power ON-OFF switch to OFF, make sure the projector works
as follows:
1. The LAMP indicator will light and the READY indicator will turn off.
2. After 90 seconds, the READY indicator will light green again and the projector
may be turned on by pressing the power ON-OFF button.
● Check the TEMPERATURE WARNING indicator. If the indicator flashes red, the
projector cannot be turned on.
(See "TURNING ON/OFF THE PROJECTOR" section on page 19.)
● Check the Projection Lamp. (Refer to page 36.)
● Adjust the focus
Image is out of
focus.
● Make sure the projection screen is at least 4.6’ (1.4m) from the projector.
● Check the projection lens to see if it needs cleaning.
NOTE : Moving the projector from a cool temperature location to a warm temperature
location may result in moisture condensation on the lens. In such an event, leave
the projector OFF and wait until condensation disappears.
● Check Ceiling / Rear feature. (See “SETTING” section on page 32.)
Picture is Left/Right
reversed.
● Check Ceiling feature. (See “SETTING” section on page 32.)
Picture is
Top/Bottom
reversed.
● Check Display feature.(See “SETTING” section on page 32.)
Some displays are
not seen during the
Operation.
● Check the connection between the computer or video equipment and the projector.
● When turning the projector on, it takes about 30 seconds to display the image.
● Check the system that you select is corresponding with the computer or the video
equipment.
No image.
● Make sure the temperature is not out of the Operating Temperature (5°C ~ 35°C).
● Check audio cable connection from audio input source.
● Adjust the audio source.
No sound.
● Press VOLUME (+) button.
● Press MUTE button.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Problem:
Remote Control Unit
does not work.
Try these Solution
● Check the batteries.
● Check the ALL-OFF switch on the Remote Control Unit is set to “ON.”.
● Make sure nothing is between the Remote Receiver and the Remote Control Unit.
● Make sure you are not too far from the projector when using the Remote Control Unit.
Maximum operating range is 16.4’ (5m).
● Check the cable connection between the projector and the computer.
● Check the mouse setting on your computer.
● Turn the projector on before you turn on the computer.
Wireless Mouse
function does not
work.
WARNING :
High voltages are used to operate this projector. Do not attempt to open the cabinet.
after following all operating instructions, contact Boxlight for assistance at 1-800-762-
If the problem still persists
5757 or 360-779-7901. Give the model number and explain the difficulty. We will advise you how to obtain
service.
Please have the following information available.
● Serial No. of projector.
● Resolution of the computer.
● Refresh rate of computer.
This symbol on the nameplate means the product is Listed by Underwriters
Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety standards
against risk of fire, casualty and electrical hazards.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
TECHNICAL SPECIFICATIONS
Multi-media Projector
Projector Type
(not including Adjustable Feet and Lens)
7.44” x 2.93” x 11.42” (189mm x 74.5mm x 290mm)
5.73 lbs (2.6 kg)
(W x H x D)
Dimensions
Net Weight
0.7” TFT Active Matrix type, 3 panels
1024 x 768 dots
LCD Panel System
Panel Resolution
Number of Pixels
Color System
2,359,296 (1024 x 768 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N
480i, 480p, 575i, 575p, 720p, 1035i and 1080i
H-sync. 15 ~ 100 KHz, V-sync. 50 ~ 100 Hz
Adjustable from 34” to 200”
High Definition TV Signals
Scanning Frequency
(Diagonal)
Projection Image size
Horizontal Resolution
Projection Lens
550 TV lines
F 1.7 ~ 1.9 lens with f 28.8 mm ~ 34.5 mm Manual zoom and focus
5.2’ ~ 26.3’ (1.6 m ~ 8.0 m)
Throw Distance
132 W
Projection Lamp
RCA Type x 3 (Video/Y, Pb/Cb, Pr/Cr) and Mini DIN 4 pin x 1 (S-Video)
AV Input Jacks
Mini Jack (stereo)
AV Audio Input Jack
Computer Input Jack
Computer Audio Input Jack
Control Port Jack
Audio Output Jack
Internal Audio Amp
Built-in Speaker
(VGA) HDB 15 Terminal x 1
Mini Jack (stereo)
Mini DIN 8 pin x 1
Mini Jack (stereo)
1W RMS (Monaural)
1 speaker, 1.57” x 1.18” (40mm x 30mm)
0˚ to 7.6˚
Feet Adjustment
Voltage and
Power Consumption
Operating Temperature
AC 100 ~ 120 V (2.4 A Max. Ampere), 50 / 60 Hz (The U.S.A and Canada)
AC 200 ~ 240 V (1.2 A Max. Ampere), 50 / 60 Hz (Continental Europe)
41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)
14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)
Storage Temperature
Power Source
:
:
:
:
AA, UM3 or R06 Type x 2
16.4’ (5m) / ±30˚
2.2” x 1.3” x 7.6” (55mm x 34mm x 192mm)
0.35 lbs (160 g) (including batteries)
Remote Control Transmitter
Operating Range
Dimensions (W x H x D)
Net Weight
Owner’s Manual
Accessories
AC Power Cord
Remote Control Transmitter and Batteries
VGA Cable
Control Cable for PS/2 port
Carry Bag
Lens Cover
● The specifications are subject to change without notice.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
BOXLIGHT CORPORATION (“BOXLIGHT”) warrants that each Boxlight XP-5t (“the Product”) sold hereunder will
conform to and function in accordance with the written specifications of BOXLIGHT. Said limited warranty shall apply
only to the first person or entity that purchases the Product for personal or business use and not for the purpose of
distribution resale. Said warranty shall continue for a period of two (2) years from the date of such purchase.
BOXLIGHT does not warrant that the Product will meet the specific requirements of the first person or entity that
purchases the Product for personal or business use. Lamp is warrantied for 120 days.
BOXLIGHT CORPORATION’s liability for the breach of the foregoing limited warranty is limited to the repair or
replacement of the Product or refund of the purchase price of the Product, at BOXLIGHT’s sole option. To exercise
the Purchaser’s rights under the foregoing warranty, the Product must be returned at the Purchaser’s sole cost and
expense, to BOXLIGHT or any authorized service center provided, however, that the Product must be accompanied by
a written letter explaining the problem and which includes (i) proof of purchase; (ii) the dealer’s name; (iii) the model
and serial number of the Product. A return authorization number, issued by the BOXLIGHT customer service
department, must also be clearly displayed on the outside of the shipping carton containing the Product.
WARRANTY LIMITATION AND EXCLUSION
BOXLIGHT CORPORATION shall have no further obligation under the foregoing limited warranty if the Product has
been damaged due to abuse, misuse, neglect, accident, unusual physical or electrical stress, unauthorized
modification, tampering, alterations, or service other than by BOXLIGHT or its authorized agents, causes other than
from ordinary use or failure to properly use the Product in the application for which said Product is intended.
DISCLAIMER OR UNSTATED WARRANTIES
The warranty printed above is the only warranty applicable to this purchase.
All other warranties express or implied, including, but not limited to, the implied warranties or merchantability and
fitness for a particular purpose are disclaimed. There are no warranties that extend beyond the face of hereof and the
foregoing warranty shall not be extended, altered or varied except by written instrument signed by BOXLIGHT
CORPORATION.
LIMITATION OR LIABILITY
It is understood and agreed that BOXLIGHT’s liability whether in contract, in tort, under any warranty, in negligence or
otherwise shall not exceed the return of the amount of the purchase price paid by purchaser and under no
circumstances shall BOXLIGHT be liable for special, indirect or consequential damages. The price stated for the
Product is a consideration in limiting BOXLIGHT’s liability. No action regardless of form, arising out of the agreement
to purchase the product, may be brought by purchaser more than one year after the cause of action has accrued.
Boxlight
19332 Powder Hill Place
Poulsbo, WA 98370-7407 USA
USA and Canada 800-762-5757
International 360-779-7901
Printed in Japan
Part No. 610 288 8027 (1AA6P1P2495-- MP6EA)
Download from Www.Somanuals.com. All Manuals Search And Download.
|