CD-850m
User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Declaration of Conformity
Manufacturer: BOXLIGHT, 19332 Powder Hill Place, Poulsbo, Washington USA
We declare under our sole responsibility that the CD-850m projector conforms to the following directives and norms:
EMC Directive 89/336/EEC, Amended by 93/68/EEC
EMC: EN 55022
EN 55024
EN 61000-3-2
EN 61000-3-3
Low Voltage Directive 73/23/EEC, Amended by 93/68/EEC
Safety: EN 60950: 2000
July, 2002
Trademarks
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer, Inc. IBM is a trademark or registered trademark of International Business
Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered trademarks of Microsoft Corporation.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide rea-
sonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a res-
idential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Safety Certifications
UL, CUL, TÜV, NOM, IRAM, GOST, CCC
Remote Control Warning
Laser radiation class II product; wavelength 650nm; maximum output 1mW. Remote control complies with applicable requirements of 21 CFR 1040.10 and 1040.11. Remote con-
trol complies with applicable requirements of EN 60 825-1: 1994 +A11.
Download from Www.Somanuals.com. All Manuals Search And Download.
If you are experienced in setting up presentation systems, use the Quick Set
Up card that was included in the carry case. For assistance, call BOXLIGHT at
1-800-762-5757 or 1-360-779-7901.
Table of Contents
Introduction
Connecting a computer
3
5
Important Operating Considerations
Required computer connections
Optional computer connections
Displaying a computer image
First-time projector use with Windows 98
Adjusting the image
Connecting a video device
Displaying a video image
Shutting down the projector
Troubleshooting your setup
Using the keypad buttons
Using the remote control
Using the audio
Optimizing computer images
Presentation features
Optimizing video images
Customizing the projector
Using the menus
5
5
7
8
Do not place the projector on a tablecloth or other soft covering that may
block the vents. Vents are placed along the left and right sides of the
CD-850m, as well as across the front of the projector. Do not use a non-
approved ceiling mount. In the unlikely event of the lamp rupturing, dis-
card any edible items placed in the surrounding area and thoroughly clean
the area along the sides and in the front of the projector.
10
11
12
14
14
22
23
24
25
25
26
26
27
28
31
34
34
35
37
38
38
38
39
Do not place objects in the areas along the side and in the front of the projector
2 ft (.6m)
2 ft (.6m)
2 ft (.6m)
Picture menu
Settings menu
Maintenance
Cleaning the lens
Replacing the projection lamp
Using the security lock
Appendix
Specifications
Accessories
Projected image size
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Included items
Introduction
Your new digital projector is easy to connect, easy to use, easy to maintain
and has XGA 1024x768 resolution.
video cable
audio cable
The projector comes in a carry case that offers ample room for BOXLIGHT
accessory items such as the projector remote, color-coded cables, and docu-
mentation. The color-coded cable straps and cables they contain make your
setup experience quick and easy, while the case’s design helps you find and
put away all items without the fear of anything becoming lost.
projector
lens cap
computer cable
video cable
power cable
power
cable
user’s guide,
quick setup card,
and safety card
computer
cable
remote
remote
color-coded cable straps
quick setup card
Cables
audio
cable
projector
user’s guide
and safety
card
power
cable
computer
cable
audio
cable
video
cable
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector components and features
computer
monitor
remote control
receiver (IR)
video
computer
1 & 2
s-video
audio
in
keypad
remote
control
receiver (IR)
video
R
Y
audio in
computer
2
computer
1
s-video
monitor out
network
R
Pb
Pr
audio in
audio in
speakers
remote
L
audio out
computer in
serial control
L
control
receiver (IR)
elevator foot release
air intake
vent
power
connector
component
video
computer 1
& 2 audio
serial
connector
network
connector
lock
carrying
handle
external
speakers
zoom
focus
(audio out)
heat vent
connectors
remote control
receiver (IR)
heat vent
leveling
foot
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a computer
connect computer cable
video
R
Y
audio in
computer
1
computer
2
s-video
monitor
network
R
Pr
audio in
audio in
L
computer in
audio out
serial control
L
Required computer connections
Pb
Connect the black end of the computer cable to the Computer 1 connector
on the projector. Connect the blue end to the video port on your computer. If
you are using a desktop computer, you first need to disconnect the monitor
cable from the computer’s video port.
Connect the black power cable to the connector on the back of the projector
and to your electrical outlet.
connect power cable
video
R
Y
audio in
computer
1
computer
2
s-video
monitor
network
R
Pr
audio in
audio in
L
computer in
audio out
serial control
L
Pb
The Power LED on the projector’s keypad turns solid green.
NOTE: Always use the power cable that shipped with the projector.
connect computer cable
video
R
Y
audio in
computer
1
computer
2
s-video
monitor
network
R
Optional computer connections
Pr
audio in
audio in
L
audio out
computer in
serial control
L
Pb
To control your computer’s mouse using the projector’s remote control, con-
nect the USB connector on the computer cable to the computer. USB drivers
must be installed to use the USB feature. For more information, see page 9.
connect audio cable
To have sound with your presentation, connect the audio cable to your com-
video
R
Y
audio in
computer
1
computer
2
s-video
monitor out
network
R
Pb
audio in
audio in
L
puter and to the computer Audio In connector on the projector.
computer in
audio out
serial control
L
Pr
If you are using a desktop computer and want to see the image on your
computer screen as well as on the projection screen, plug the monitor cable
to the Monitor out connector on the projector.
connect monitor cable
video
R
Y
audio in
computer
1
computer 2
s-video
monitor out
network
R
Pb
audio in
audio in
L
computer in
audio out
serial control
L
Pr
5
Download from Www.Somanuals.com. All Manuals Search And Download.
If you prefer connecting your computer to the projector with an optional
VESA cable, connect one end of the cable to the VESA port on your com-
puter, and connect the other end of the cable to the blue Computer 2 con-
nector on the projector.
connect VESA cable
video
R
Y
audio in
computer
1
computer
2
s-video
monitor
network
R
Pr
audio in
audio in
L
computer in
audio out
serial control
L
Pb
You can control the projector from an LCD control panel or computer by
connecting an RS-232 cable to the projector’s Serial connector.
connect RS-232 cable
video
R
Y
audio in
audio in
computer
1
computer 2
s-video
monitor
network
R
Pr
audio in
L
computer in
audio out
serial control
L
Pb
The projector can be managed by networking software through its Network
connector.
connect network cable
video
R
Y
audio in
computer
1
computer
2
s-video
monitor
network
R
Pr
audio in
audio in
L
audio out
computer in
serial control
L
Pb
Network
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Displaying a computer image
Remove the lens cap.
remove lens cap
press Power
Press the Power button on the top of the projector or the remote.
The LED flashes green and the fans start to run. When the lamp comes on,
the startup screen is displayed and the LED is steady green. It can take a
minute for the image to achieve full brightness.
? No startup screen? Get help on page 15.
turn on computer
Turn on your computer.
The computer’s image should appear on the projection screen. If it doesn’t,
press the Computer button on the projector’s keypad.
activate laptop’s external port
Make sure your laptop’s external video port is active.
Many laptops do not automatically turn on their external video port when a
projector is connected. Usually a key combination like FN + F5 is used to
turn the external display on and off. Refer to your computer’s documenta-
tion to learn your computer’s key combination.
? No computer image? Try pressing the Auto Image
button on the keypad. Get help on page 15.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
First-time projector use with Windows 98
a
The first time you connect a computer running Windows 98 to the projector,
the computer recognizes the projector as “new hardware” and the Add
New Hardware Wizard appears. Follow these instructions to use the Wiz-
ard to load the correct driver (which was installed with your Windows
operating system).
If you are running Windows 2000, Windows ME, or Window XP, skip these
steps and go to “Adjusting the image” on page 10.
a Click Next to begin searching for the driver.
b
b Make sure “Search for the best driver” is selected, then click Next.
c Uncheck any checked boxes, then click Next. Windows automatically
locates the driver. If this driver has been removed, reload the driver using
your Windows operating system CD.
c
d When Windows finds the driver, you are ready to install it. Click Next.
d
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Skip this page if you did not connect a USB mouse cable
For Windows 98:
•
If you connected the USB cable, the Add New Hardware Wizard
appears again. Drivers must be installed to use the USB functionality.
•
The Wizard launches three times.
The first time it detects a USB Composite Device.
The second time a USB Human Interface Device (for the keyboard).
The third time it detects a USB Human Interface Device (for the
mouse).
For Windows 2000, Windows ME, and Windows XP:
The USB drivers are automatically installed.
•
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the image
adjust height
Adjust the height of the projector, if necessary, by pressing the release but-
ton to extend the elevator foot.
rotate level-
ing foot
Rotate the leveling foot, if necessary.
elevator foot
Position the projector the desired distance from the screen at a 90 degree
angle to the screen.
adjust distance
See page 39 for a table listing screen sizes and distances.
Adjust the zoom or focus rings by rotating them until the desired image size
and sharpness are produced.
adjust zoom and focus
zoom
focus
If the image is not square, adjust the keystone by using the buttons on the
keypad.
adjust keystone
Press the upper Keystone button to reduce the upper part of the image, and
press the lower Keystone button to reduce the lower part.
Adjust the Contrast or Brightness in the Picture menu.
See page 27 for help with the menus.
adjust Contrast or Brightness
contrast
brightness
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a video device
Standard video connections
video
R
connect video cable
Y
audio in
computer
1
computer
2
s-video
monitor
network
R
Pr
audio in
audio in
L
computer in
audio out
serial control
L
Pb
Plug the video cable’s yellow connector into the video-out connector on the
video device. Plug the other yellow connector into the yellow Video con-
nector on the projector.
Plug a white connector into the left audio out connector on the video device
and plug a red connector into the right audio out connector on the video
device.
Plug the remaining white connector into the left audio in connector on the
projector, and plug the red connector into the right audio in connector on
the projector.
Connect the black power cable to the connector on the back of the projector
and to your electrical outlet. The Power LED on the keypad turns solid
green.
video
R
Y
audio in
computer
1
computer
2
s-video
monitor
network
R
Pr
audio in
audio in
L
computer in
audio out
serial control
L
connect power cable
Pb
NOTE: Always use the power cable that shipped with the projector.
Optional video connections
video
R
Y
audio in
computer
1
computer
2
If the video device uses a round, four-prong S-video connector, plug an
S-video cable (sold separately) into the S-video connector on the video
device and into the S-video connector on the projector. Use the video cable’s
audio connectors as described directly above (the yellow connectors on the
video cable are not used).
s-video
monitor
network
R
connect S-video and video cables
Pr
audio in
computer in
audio in
L
audio out
serial control
L
Pb
If the video device uses component cable connectors (sold separately), plug
the cable’s green connectors into the green component-out connector on the
video device and into the green component connector (labeled “Y”) on the
projector. Plug the component cable’s blue connectors into the blue compo-
nent-out connector on the video device and into the blue component con-
nector (labeled “Pb”) on the projector. Plug the component cable’s red
connectors into the red component-out connector on the video device and
into the red component connector (labeled “Pr”) on the projector. Use the
video cable’s audio connectors as described directly above (the yellow con-
nectors on the video cable are not used).
connect component cables
and video cables
video
R
Y
audio in
computer
1
computer
2
s-video
monitor
network
R
Pr
audio in
audio in
L
computer in
audio out
serial control
L
Pb
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Displaying a video image
Remove the lens cap.
remove lens cap
press Power
Press the Power button on the top of the projector.
The LED flashes green and the fans start to run. When the lamp comes on,
the startup screen is displayed and the LED is steady green. It can take a
minute for the image to achieve full brightness.
? No startup screen? Get help on page 14.
Plug in and turn on the video device.
turn on video device
The video device’s image should appear on the projection screen. If it
doesn’t, press the Video button on the keypad.
Adjust the height of the projector by pressing the release button to extend
the elevator foot. Rotate the leveling foot, if necessary.
adjust height
rotate
leveling
foot
elevator
foot
adjust distance
Position the projector the desired distance from the screen at a 90 degree
angle to the screen. See page 39 for a table listing screen sizes and distances
to the screen.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjust the zoom or focus rings by rotating them until the desired image size
and sharpness are produced.
adjust zoom and focus
zoom
focus
If the image is not square, adjust the keystone using the buttons on the key-
pad. Press the upper Keystone button to reduce the upper part of the
image, and press the lower Keystone button to reduce the lower part.
adjust keystone
adjust volume
Adjust the volume on the keypad or remote.
contrast
Adjust the Contrast, Brightness, Color, or Tint in the Picture menu.
adjust Picture menu
brightness
See page 27 for help with the menus.
color
tint
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Shutting down the projector
Troubleshooting your setup
The projector automatically displays a black screen after no active source is
detected for 30 minutes. This black screen helps preserve the life of the pro-
jector. The image returns when an active source is detected or a remote or
keypad button is pressed.
If your image appears correctly on the screen, skip to the next section
(page 23). If it does not, troubleshoot the setup.
The LED on top of the projector’s keypad indicates the state of the projector
and can help you troubleshoot.
Screen Save
You can make the black screen appear after five minutes by turning on
Screen Save in the Settings>System menu. See page 32. There are six time
options for the Screen Save feature. They range from five minutes to 30 min-
utes with five minute intervals.
Table 1: LED behavior and meaning
LED color/behavior
Meaning
solid green
The projector is plugged in, or the projec-
tor has been turned on and the software
has initialized. The projector has been
turned off and the fans have stopped.
Power Save
The projector also has a Power Save feature that automatically turns the
lamp off after no signals are detected for 20 minutes. After 10 additional
minutes with no signal, the projector powers down. If an active signal is
received before the projector powers down, the image is displayed. You
must press the Power button to display an image after 30 minutes have
passed. When Power Save is enabled, Screen Save is disabled. See page 31.
blinking green
blinking red
The power button has been pressed and
the software is initializing, or the projec-
tor is powering down and the fans are
running to cool the lamp.
Turning off the projector
A fan or lamp failure has occurred. Turn
off the projector and wait one minute,
then turn the projector on again. If the
projector has been working for 2,000
hours or more, replace the lamp and reset
the lamp timer. Also check for a blocked
vent or a stopped fan.
To turn off the projector, press the power button and verify that you want to
turn the projector off by pressing the power button again within 3 seconds.
You can cancel the shutdown by not pressing the power button a second
time. The lamp turns off and the LED blinks green for 1 minute while the
fans continue to run to cool the lamp. When the lamp has cooled, the LED
lights green and the fans stop. Unplug the power cable to completely power
off the projector.
solid red
An unidentifiable error: please contact
Technical Support.
The following tables show common problems. In some cases, more than one
possible solution is provided. Try the solutions in the order they are pre-
sented. When the problem is solved, you can skip the additional solutions.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Source troubleshooting
Problem
Solution
Result
Plug power cable in and remove lens cap
press power button
No startup screen
Correct image
Computer image projected
Only startup screen appears
Press the Computer button
Activate laptop’s external port
A
A
A
or restart
laptop
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjust computer refresh rate in Control
Panel>Display>Settings>Advanced>
Adapter (location varies by operating
system)
No computer image, just the words “Signal out of
range”
Computer image projected
Signal
range
out
A
of
A
A
You may also need to set a different
resolution on your computer, as shown
in the following Problem, “Image fuzzy
or cropped”
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Set your computer’s display resolution to
the native resolution of the projector
(Start>Settings>Control
Panel>Display>Settings tab,
select1024x768)
Image clear and not cropped
Image fuzzy or cropped
A
A
A
For a laptop,
disable laptop
monitor
or turn-on dual-
display mode
Remote controls computer cursor. Note
that the mouse is not functional in zoom
mode (see page 32)
Connect computer cable (page 5), then,
load USB drivers, if needed (page 8)
Remote control not controlling my computer’s
mouse
See page 23 for information on the remote
video
R
Y
audio in
computer
1
computer
2
s-video
monitor
network
R
Pr
audio in
audio in
L
computer in
audio out
serial control
L
Pb
X
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector troubleshooting
Problem
Solution
Result
Square image
Adjust keystone on keypad
Image not square
Turn Overscan on in the Picture>Advanced
menu
Correct image
Edges of image distorted
A B
A B
A B
Adjust Sharpness in the Picture>Advanced
menu
Correct image
Image not sharp
A B
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Change aspect ratio to 16:9 in
Picture>Aspect ratio menu
Correct image
Image does not fit 16:9 screen
Correct image
Turn off Ceiling in Settings>System menu
Image upside down
B
A
A B
Image reversed left to right
Turn off Rear in Settings>System menu
Correct image
A
A B
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Change Video Standard in
Picture>Advanced menu
Correct image
Video image “torn” and fragmented
AB
A
A B
B
Adjust color, tint, color temperature,
brightness, contrast in the menus
Projected colors don’t match source
Correct image
COLOR
COLOR
Make sure vents aren’t blocked; allow
projector to cool for one minute
Unplug projector; wait one minute; plug in
projector and turn it on: lamp lights
Lamp won’t turn on, LED blinking red (page 14)
blinks
red
Check lamp hours:
should be less
than 2,000 hours
in the
Main>About menu
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Lamp must be replaced (page 35)
Lamp won’t turn on, LED blinking red (page 14)
Lamp turns on
blinking
red
Correct image
Move projector, adjust zoom, adjust height
Image not centered on screen
zoom
adjust horizontal or vertical position in
Picture>Advanced menu
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Regarding this projector
For assistance, call BOXLIGHT at 1-800-762-5757 or 1-360-779-7901.
Using the keypad buttons
Most buttons are described in detail in other sections, but here is an over-
view of their functions:
This product is backed by a limited two-year warranty. An extended war-
ranty plan may be purchased from BOXLIGHT.
power–turns the projector on (page 7) and off (page 12).
menu–opens the on-screen menus (page 27).
When sending the projector in for repair, we recommend shipping the unit
in the carry case in its original packing material, or having a professional
packaging company pack the unit with all accessories for shipping. Please
insure your shipment for its full value.
select–confirms choices made in the menus (page 27).
up/down arrows–navigates to and adjusts settings in the menus (page 27).
auto image–resets the projector to the source.
presets–cycles through the available preset settings (page 29).
keystone–adjusts squareness of the image (page 10).
volume–adjusts sound (page 24).
video and computer–changes the active source.
menu navigation buttons
22
Download from Www.Somanuals.com. All Manuals Search And Download.
the PowerPoint Tools menu, click the View Tab, de-select the “Popup Menu
on Right Mouse Click” option in the Slide Show section, then click OK.
Then, when you’re in PowerPoint’s Slide Show mode, a left click advances
to the next slide and a right click returns to the previous slide (other Power-
Point modes are not affected).
Using the remote control
The remote uses two (2) provided AAA batteries. They are easily installed
by sliding the cover off the remote’s back, aligning the + and - ends of the
batteries, sliding them into place, and then replacing the cover.
To operate, point the remote at the projection screen or at the projector (not
at the computer). The range of optimum operation is about 30 feet (9.14m).
cursor control
backlight button
To use the laser pointer, press and hold the Laser button. The laser turns off
when the button is released, or times out after two (2) minutes of continu-
ous operation.
left mouse button
navigation buttons
right mouse button
Left and right remote mouse buttons are used to mimic the actions of the
left/right mouse buttons on your computer. Mouse cursor movement is
managed via the remote’s Cursor control. Connect the USB connector on the
computer cable to your computer to use these buttons and control your
computer’s mouse. When you do this for the first time, the Add New Hard-
ware wizard may appear. See page 8 for details on loading the correct USB
drivers.
Press the remote’s Menu button to open the projector’s menu system. Use
the arrow buttons to navigate, and the Select button to select features and
adjust values in the menus. See page 27 for more info on the menus.
Troubleshooting the remote
•
•
•
Make sure the batteries are installed in the proper orientation and are
not dead.
The remote also has a power button to turn the projector on and off (see
page 14 for shutdown info), volume and mute buttons to control the sound,
a backlight button to light the remote’s buttons in the dark, and video and
computer buttons to switch between sources.
Make sure you’re pointing the remote at the projector, not the com-
puter, and are within the remote range of 30 feet (9.14m).
If you are trying to control your computer’s mouse, make sure the USB
cable is connected. If using a USB cable, make sure the correct drivers
are installed.
Two presentation-specific features are also provided. Use the blank button
to display a blank screen instead of the current slide (you can choose which
color is displayed, see page 32); use the effect button to invoke a user-defin-
able action, such as freeze or zoom (see page 32 to learn to program this but-
ton).
®
®
If you are displaying presentations in Microsoft PowerPoint , you can use
the remote’s mouse buttons to navigate through your presentation while in
Slide Show mode. To configure PowerPoint for this, choose Options from
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the audio
connect audio cable
video
To play sound from the projector, connect your source to the Audio In con-
nector on the projector.
R
Y
audio in
computer
1
computer
2
s-video
monitor out
network
R
Pb
audio in
audio in
L
computer in
audio out
serial control
L
Pr
To adjust the volume, use the buttons on the keypad or remote.
To mute the sound, press the Mute button.
Troubleshooting audio
If there is no sound, check the following:
adjust volume
•
•
•
Make sure the audio cable is connected.
Make sure mute isn’t active.
Make sure the volume is turned up enough. Press the volume button
on the keypad or remote.
•
Make sure that if you are connected to Computer 1 on the back of the
projector, that you are also connected to the corresponding audio in. If
you are connected to Computer 2, be sure you are connected to its cor-
responding audio in.
computer 1 and
corresponding audio
•
•
Adjust the audio source.
If playing a video, make sure the playback has not been paused.
computer 2 and
corresponding audio
audio in
computer
2
computer
1
audio in
computer in
video
R
Y
audio in
computer
1
computer
2
s-video
monitor
network
R
Pr
audio in
audio in
Connecting external speakers
L
computer in
audio out
serial control
L
external
speakers
Pb
The projector can be attached to external speakers that have their own
power source by plugging speaker cables into the projector’s left and right
Audio Out connectors.
audio out
speaker
cable
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Optimizing computer images
Presentation features
After your computer is connected properly and the computer’s image is on
the screen, you can optimize the image using the onscreen menus. For gen-
eral information on using the menus, see page 27.
Several features are provided to make giving presentation easier. The fol-
lowing is an overview, details are found in the menu section on page 27.
•
The remote’s Effect button allows you to assign various features to the
key. The default effect is About, which displays information about the
projector and current source. You can select from Blank, Mute, Aspect
Ratio, Source, Auto Image, Freeze, Zoom, and About. See page 32 for
details.
•
•
Adjust the Keystone, Contrast, or Brightness in the Picture menu.
Change the Aspect Ratio. Aspect Ratio is the ratio of the image width to
image height. TV screens are usually 1.33:1, also known as 4:3. HDTV
and most DVDs are 1.78:1, or 16:9. Choose the option that best fits your
input source. See page 28 for details.
•
The Freeze effect allows you to freeze the displayed image. This is use-
ful if you want to make changes on your computer without your audi-
ence seeing them.
•
•
Adjust the Color Space or Color Temperature in the Advanced menu.
Adjust the Phase, Tracking, or Horizontal or Vertical position in the
Advanced menu.
•
•
•
The Blank button on the remote allows you to display a blank screen
instead of the active source. See page 32.
•
Once you have optimized the image for a particular source, you can
save the settings using Presets. This allows you to quickly recall these
settings later. See page 29.
The Startup Logo menu option lets you change the default startup
screen to a black, white, or blue screen. See page 32.
Two menu options, Power Save and Screen Save, are provided to auto-
matically shut down the projector after several minutes of inactivity or
display a black screen. This helps preserve lamp life. See page 31 and
page 32.
•
A Low Power menu option is also available to help lower the projec-
tor’s fan sound volume. See page 31.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Optimizing video images
Customizing the projector
After the video device is connected properly and the image is on the screen,
you can optimize the image using the onscreen menus. For general informa-
tion on using the menus, see page 27.
You can customize the projector for your specific setup and needs. See
page 31 to page 34 for details on these features.
•
•
For rear projection, turn Rear mode on in the Settings>System menu.
•
Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Picture
menu. See page 28.
For ceiling mounted projection, turn Ceiling mode on in the Set-
tings>System menu.
•
Change the Aspect ratio. Aspect ratio is the ratio of the image width to
image height. TV screens are usually 1.33:1, also known as 4:3. HDTV
and most DVDs are 1.78:1, or 16:9. Choose the option that best fits your
input source. See page 28.
•
Specify which source the projector checks first for active video during
power-up.
•
•
•
•
•
Specify the function of the Effect Key on the remote.
Turn the projector’s display messages on and off.
Turn on power saving features.
•
•
Select a Sharpness setting. See page 30.
Adjust the Color Temperature. Select a listed value, or select User and
individually adjust the intensity of the red, green, and blue color. See
page 30.
Specify blank screen colors and startup logos.
Specify the menu language.
•
•
Select a different Video Standard. Auto tries to determine the standard
of the incoming video. Select a different standard if necessary. See
page 30.
Turn overscan on to remove noise around the video image. See page 30.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menus
Dot
To open the menus, press the menu button on the keypad or remote. (The
menus automatically close after 60 seconds if no buttons are pressed.) The
Main menu appears. Use the arrow buttons to move up and down to high-
light the desired submenu, then press the Select button.
Menu
button
To change a menu setting, highlight it, press Select, then use the up and
down arrow buttons to adjust the value, select an option using radio but-
tons, or turn the feature on or off using check boxes. Press Select to confirm
your changes. Use the arrows to navigate to another setting. When your
adjustments are complete, navigate to Exit, then press Select to go to the
previous menu; press the Menu button at any time to close the menus.
Keypad navigation
buttons
Main menu
Picture
menu
Dots appear before the menu name. The number of dots indicate the menu’s
level, ranging from one (the Main menu) to four (the most nested menus).
Dots
The menus are grouped by usage:
•
•
The Picture menu provides image adjustments.
Settings
menu
The Settings menu provides set-up type adjustments that are not
changed often.
•
The About menu provides a read-only display of information about the
projector and source.
Certain menu items may be hidden until a particular source is connected.
For example, Sharpness is only available for video sources and will be hid-
den when a computer source is active. Other menu items may be grayed out
when they are not available. For example, Brightness is grayed out until an
image is active.
About menu
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture menu
To adjust the following five settings, highlight the setting, press Select, use
the up and down arrows to adjust the values, then press select to confirm
the changes.
increasing keystone
decreasing keystone
Keystone: adjusts the image vertically and makes a squarer image. You can
also adjust keystone from the keypad.
Contrast: controls the degree of difference between the lightest and darkest
parts of the picture and changes the amount of black and white in the
image.
Brightness: changes the intensity of the image.
Color: (video sources only) adjusts a video image from black and white to
fully saturated color.
Tint: (NTSC video sources only) adjusts the red-green color balance in the
image.
Aspect Ratio: Aspect ratio is the ratio of the image width to image height.
TV screens are usually 1.33:1, also known as 4:3. HDTV and most DVDs are
1.78:1, or 16:9. The default is 4:3, which displays the input resized up or
down to fill the display area.
Aspect ratio
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Presets: The provided Presets optimize the projector for displaying com-
puter presentations, photographs, film images, and video images. (Film
input is material originally captured on a film camera, like a movie; video
input is material originally captured on a video camera, like a TV show or
sporting event.) You can use the preset as a starting point, then further cus-
tomize the settings for each source. The settings you customize are saved in
the preset for each source. To restore the factory default settings, choose Fac-
tory Reset in the Settings>Service menu.
Presets
Save User Presets
There are also three user-definable presets. To set a preset for the current
source, adjust the image, select Save Settings in the Presets menu, then
choose Save User 1, 2, or 3. You can recall these settings in the future by
selecting the appropriate user presets.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced settings
Sharpness: (video sources only) changes the clarity of the edges of a video
image. Select a sharpness setting.
Sharpness
Color Space: This option applies to computer and component video
sources (it won’t appear in the menu for S-video or composite video
sources). It allows you to select a color space that has been specifically tuned
for the video input. When Auto is selected, the projector automatically
determines the standard. To choose a different setting, turn off Auto, then
choose RGB for computer sources, choose either SMPTE240, REC709, or
REC601 for component video sources.
Color Temperature: changes the intensity of the colors. Select a listed
value, or select User and individually adjust the intensity of the red, green,
and blue colors.
Video Standard: When it is set to Auto, the projector attempts to pick the
video standard automatically based on the input signal it receives. (The
video standard options may vary depending on your region of the world.) If
the projector is unable to detect the correct standard, the colors may not
look right or the image may appear “torn.” If this happens, manually select
a video standard by selecting NTSC, PAL, or SECAM from the Video Stan-
dard menu.
Color Space
Color Temperature
Overscan: (video sources only) removes noise around the video image.
The following 4 options are for computer sources only.
Phase: adjusts the horizontal phase of a computer source.
Tracking: adjusts the vertical scan of a computer source.
Video Standard
Horizontal/Vertical Position: adjusts the position of a computer source.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings menu
Audio: allows adjustments to the sound Balance between speakers and
speaker Volume. The Internal speakers and projector startup Chime can be
turned on or off by placing or removing a check in the respective check-
boxes.
Audio
Sources>Power-up Source: this determines which source the projector
checks first for active video during power-up.
Sources: allows you to assign a particular input to a specific source key as
an optional full-featured remote. Also allows selection of a default Power-
up Source and enables or disables Autosource. When Autosource is not
checked, the projector defaults to the source selected in Power-up Source. If
no source is found, a blank screen displays. When Autosource is checked,
Power-up Source determines which source the projector defaults to at
power-up. If no signal is present, the projector checks the sources in order
until a source is found or until power down.
Power-up
Source
Sources
System>Rear: reverses the image so you can project from behind a translu-
cent screen.
Ceiling: turns the image upside down for ceiling-mounted projection.
NOTE: It is recommended that all final image adjustments in Ceiling mode
are made once the unit has fully warmed up.
System menu
Auto Power: When Auto Power is checked, the projector automatically
goes into the startup state after the projector is powered on. This allows con-
trol of ceiling mounted projectors with a wall power switch.
Display Messages: displays status messages (such as “Searching” or
“Mute”) in the lower-left corner of the screen.
Low Power: toggles between on and off. Turn it on to lower the light output
of the lamp. This also lowers the fan speed, making the projector quieter.
Power Save: automatically turns the lamp off after no signals are detected
for 20 minutes. After 10 additional minutes with no signal, the projector
powers down. If an active signal is received before the projector powers
down, the image will be displayed.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Screen Save: automatically blanks the screen with a black color after no sig-
nals are detected for a preset number of minutes. The image returns when
an active source is detected or a remote or keypad button is pressed. Screen
Save is disabled when Power Save is enabled.
Startup logo
Blank Screen
Screen Save
Startup Logo: allows you to display a blank Black, White, or Blue screen
instead of the default screen at startup and when no source is detected.
Blank Screen: determines what color displays when you press the Blank
button on the remote or there is a blank screen when no source is active.
Effect Key: allows you to assign a different function to the Effect button on
the remote to quickly and easily use the effect. Only one effect can be
enabled at a time. Highlight an effect and press Select to choose a different
one.
Effect Key
Blank: shows an empty screen.
Mute: turns off all sound.
Aspect Ratio: sets the ratio of the image width to image height.
Source: cycles through the available sources.
Auto Image: causes computer sources to be reacquired.
Freeze: pauses the projected image.
Zoom: lets you magnify a part of the screen. To use the Zoom effect,
press Effect, then press the remote’s mouse left-click to zoom the
image, press the mouse right-click to decrease the magnification. You
can use the cursor control to pan the image, displaying different parts
of it (only if the image is magnified). To return to the original size and
cancel Zoom, press the Effect button a second time.
About: is the default effect. It displays the About menu.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Network: The projector has an RJ45 Ethernet connector that supports net-
work connections and TCP/IP protocols. This will allow for the control and
management of the projector over a corporate network. The following fields
are accessible when DHCP is not checked and available for manual entry of
data.
Network
Network
Info
IP Address: Identifies the projector on the network.
Subnet mask: Separates the network address part of the IP address.
Default gateway: The IP address of the local router.
DHCP: Select this to automatically obtain an IP address, Subnet mask,
and Default gateway.
Network Info: Provides information on the network configuration.
The Network Info menu is informational and cannot be edited. It displays
the current IP Address, Subnet Mask, Default Gateway, and the projector’s
MAC Address.
Language: allows you to select a language for the onscreen display of
menus and messages.
Language
Service:
To use these features, highlight them and press Select.
Factory Reset: restores all settings (except Lamp Hours and Network set-
tings) to their default after displaying a confirmation dialog box.
Lamp Reset: resets the lamp hours counter in the About menu to zero. Do
Service menu
this only after changing the lamp. It displays a confirmation dialog box.
Service Code: only used by authorized service personnel.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
clean the lens
with a soft dry cloth
and non-abrasive
cleaner
Cleaning the lens
1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
Avoid using an excessive amount of cleaner, and don’t apply the
cleaner directly to the lens. Abrasive cleaners, solvents or other harsh
chemicals might scratch the lens.
2 Lightly wipe the cleaning cloth over the lens in a circular motion. If you
don’t intend to use the projector immediately, replace the lens cap.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the projection lamp
The lamp hour timer in the About menu counts the number of hours the
lamp has been in use. After 1,980 hours, the message “Change lamp” briefly
appears on the screen at each startup. When the timer reaches 2,000 hours,
the lamp will no longer light. You can order new lamp modules from BOX-
LIGHT. See “Accessories” on page 38 for information.
About menu
video
R
turn off and unplug
the projector
Y
audio in
computer
1
computer
2
s-video
monitor out
network
R
Pb
audio in
audio in
L
computer in
audio out
serial control
L
Pr
1 Turn off the projector and unplug the power cable.
2 Wait 60 minutes to allow the projector to cool thoroughly.
wait 60 minutes
3 Turn the projector upside down and remove the lamp door by removing
the two screws and sliding the lamp door tabs out of the three tab bays.
CAUTION: Never operate the projector with the lamp door removed.
This disrupts the air flow and causes the projector to overheat.
4 Loosen the captive screw on the lamp module.
loosen the screw on lamp module
bail wire
35
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNINGS:
•
To avoid burns, allow the projector to cool for at least 60 minutes before
you replace the lamp.
•
•
Do not drop the lamp module. The glass may shatter and cause injury.
Do not touch the glass lamp screen. Fingerprints can obscure projection
sharpness.
•
Be extremely careful when removing the lamp housing. In the unlikely
event that the lamp ruptures, small glass fragments may be generated.
The lamp module is designed to contain most of these fragments, but
use caution when removing it.
5 Carefully remove the lamp module by grasping and lifting the metal
bail wire. Dispose of the lamp in an environmentally proper manner.
6 Install the new lamp module, making sure that it is properly seated.
7 Tighten the single screw.
8 Replace the lamp door by sliding the tabs into the tab bays and tighten-
ing the two screws.
9 Plug in the power cable, then press the Power button to turn the projec-
tor back on.
10 Reset the lamp hour timer.
Resetting the lamp timer
reset lamp time in Service menu
If the lamp timer has reached the maximum number of hours for the projec-
tor lamp (2,000 hours), the LED on the projector’s keypad will show a lamp
error (see “LED behavior and meaning” on page 14). To reset the lamp age,
simultaneously holding down the two Volume keys on the projector’s key-
pad for 10 seconds. At that point the LED will turn green and you can
power on the projector.
You can also navigate to the Settings>Service menu and select Lamp Reset
to reset the lamp timer.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the security lock
video
R
The projector has a security lock for use with a PC Guardian Cable Lock
System. See “Accessories” on page 38 for ordering information. Refer to the
information that came with the lock for instructions on how to use it.
Y
audio in
computer
2
computer
1
s-video
monitor out
network
R
Pb
audio in
audio in
L
computer in
serial control
audio out
L
Pr
security lock
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
Appendix
Specifications
Standard Accessories
(ship with the projector)
Carrying Case
Shipping Box (with packaging)
Computer Cable 6 ft (1.8 m)
Audio/Video Cable 6 ft (1.8 m)
Audio Cable 6 ft (1.8 m)
Power Cable (country-dependent)
Conductor Plus Remote
Temperature Operating
50 to 95° F (10 to 35° C) at 0 - 10,000 feet
-4 to 158° F (-20 to 70° C) at 0 -20,000 feet
Non-operating
Altitude Operating
0 to 10,000 feet (3,048 meters)
0 to 20,000 feet (6,096 meters)
Non-operating
Humidity Operating
10% to 95% relative humidity, non-condensing
10% to 90% relative humidity, non-condensing
Projection Lamp Module (included
in projector)
Non-operating
Lens Cap
13.8 x 12.8 x 4.3” (351W x 325L x 110H mm)
Dimensions
Weight
Quick Setup card
User’s Guide
9.3 lbs. (4.24 kg) unpacked
Safety Card
Color-coded Cable Ties, 3 set
5 - 32.8 feet (1.5 - 10 meters)
250-watt UHP lamp
Optics Focus Range
Lamp Type
Input Power Requirements 100V-120V 4A, 50/60 Hz
200V-240V 2A 50 Hz
Ceiling Mount UL tested/listed ceiling mount with minimum capacity of
46 lbs (20.87 kg)
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Projected image size
Table 2:
Optional Accessories
Range of distance to the screen for a given screen size for CD-850m
Shipping Case (ATA approved)
Deluxe Travel Case
Distance to screen
Diagonal
Screen Size
(inches/m)
Maximum
distance
(feet/m)
Minimum
Distance
(feet/m)
Projector Mount
Image Width
(inches/m)
False Ceiling Plate for Projector Mount
Extension Arm for Projector Mount
PC Guardian Cable Lock System
60” Diagonal Screen (portable)
80” Diagonal Screen (portable)
Various Wall/Ceiling Mounted Screens
Portable Projector Stand
40/1.0
50/1.3
32/0.8
40/1.0
48/1.2
79/2.0
119/3.0
158/4.0
6.9/2.1
8.7/2.6
5.0/1.5
6.2/1.9
60/1.5
10.4/3.2
17.4/5.3
26.0/7.9
34.7/10.6
7.5/2.3
100/2.5
150/3.8
200/5.1
12.4/3.8
18.7/5.7
24.9/7.6
Replacement Lamp Module
Various RF Remotes
NOTE: Use only approved accessories.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Drivers 8
USB 9
Numerics
1024x768 resolution 3
Windows 98 9
A
E
About 32
Effect Key 32
elevator foot 10
F
FCC warning 1
first time use
altitude limits 38
Aspect Ratio 32
audio 24
Audio In connector 5, 11
audio volume 13
Auto Image 32
Auto Power 31
B
driver installation 8
focus 10, 13
Freeze 32
fuzzy image 17
I
image
display video 12
image display
Blank 32
blinking green 14
blinking red 14
Brightness 10
C
computer 7
cables
image does not fit screen 19
image edges distorted 18
image not centered 21
image not sharp 18
image not square 18
image reversed 19
image size matrix 39
image torn 20
image upside down 19
Info
network 33
IP Address 33
optional 39
cleaning the lens 34
Color 13
colors are incorrect 20
component cable connector 11
Computer 1 connector 5
Computer 2 connector 6
computer connections
optional 5
required 5
computer image
optimize 25
K
Contrast 10, 13
Keystone 10, 13
D
Declaration of Conformity 1
Default gateway 33
DHCP 33
Display Messages 31
40
Download from Www.Somanuals.com. All Manuals Search And Download.
remote’s mouse buttons 23
presentation features 25
projector
L
lamp replacement 35
lamp won’t turn on 20, 21
Language 33
customizing 26
optional accessories 39
shutdown 14
laptop
external video port 7
LED
standard accessories 38
troubleshooting problems 14
projector height 10, 12
projector positioning 10, 12
projector specifications 38
R
Rear 31
remote control 23
not working 17
blinking green 14
blinking red 20
solid green 14
solid red 21
LED behavior 14
Lens cleaning 34
leveling foot 10
Low Power 31
M
Main menu 27
menu system 27
Monitor connector 5
mouse, using your 5
Mute 32
Remote control warning 1
replacing the lamp 35
RS-232 cable 6
S
Safety Certifications 1
security lock 37
Serial connector 6
Settings menu 31
shutdown
projector 14
solid green 14
solid red 14
Source 32
Source troubleshooting 15
Sources 31
standard accessories
projector 38
Subnet mask 33
S-video connector 11
N
Network 33
Network connector 6
Network Info 33
no computer image 16
no startup screen 15
O
only startup screen appears 15
optional accessories 39
P
Picture menu 28
Power button 12
power cable 5, 11
Power Save 31
PowerPoint
41
Download from Www.Somanuals.com. All Manuals Search And Download.
T
temperature limits 38
Tint 13
Troubleshooting 14, 15
U
USB, using your mouse 5
V
VESA port 6
Video button 12
video connections
optional 11
standard 11
Video connector 11
video images
optimizing 26
W
warranty 22
Windows 2000 9
Windows 98 8
Windows ME 9
Windows XP 9
X
XGA 3
Z
zoom 10, 13, 32
42
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
DISCLAIMER OF UNSTATED WARRANTIES
BOXLIGHT (“BOXLIGHT”) warrants that the CD-850m (“the Product”) sold hereunder
will conform to and function in accordance with the written specifications of BOX-
LIGHT. Said limited warranty shall apply only to the first person or entity that pur-
chases the Product for personal or business use and not for the purpose of
distribution or resale. Said warranty shall continue for a period of two (2) years from
the date of such purchase. The standard limited warranty excludes the lamps in pro-
jectors after 120 days and the accessories after one year. BOXLIGHT does not warrant
that the Product will meet the specific requirements of the first person or entity that
purchases the Product for personal or business use. BOXLIGHT’s liability for the breach
of the foregoing limited warranty is limited to the repair or replacement of the Prod-
uct or refund of the purchase price of the Product, at BOXLIGHT’s sole option. Replace-
ment Product may be re-furbished in “like-new” condition, at BOXLIGHT’s sole
discretion. To exercise the Purchaser’s rights under the foregoing warranty, the Prod-
uct must be returned at the Purchaser’s sole cost and expense, to BOXLIGHT or to any
authorized BOXLIGHT service center provided, and the Product must be accompanied
by a written letter explaining the problem and which includes (i) proof of date of pur-
chase; (ii) the dealer’s name; and (iii) the model and serial number of the Product.
When sending your unit in for repair, please ship your unit in its original packing
material or a BOXLIGHT approved ATA Shipping Case, or have a professional packag-
ing company pack the unit. Please insure your shipment for its full value. A return
authorization number, issued by the BOXLIGHT customer service department,
must also be clearly displayed on the outside of the shipping carton containing
the Product.
THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLICABLE TO
THIS PURCHASE. ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUD-
ING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MER-CHANTABIL-
ITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. THERE
ARE NO WARRANTIES THAT EXTEND BEYOND THE FACE HEREOF AND THE
FOREGOING WARRANTY SHALL NOT BE EXTENDED, ALTERED OR VARIED
EXCEPT BY WRITTEN INSTRUMENT SIGNED BY BOXLIGHT. SOME STATES DO
NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY MAY
LAST, SO SUCH LIMITATIONS MAY NOT APPLY TO YOU.
LIMITATION OF LIABILITY
IT IS UNDERSTOOD AND AGREED THAT BOXLIGHT’S LIABILITY WHETHER IN
CONTRACT, IN TORT, UNDER ANY WARRANTY, IN NEGLIGENCE OR OTHER-
WISE SHALL NOT EXCEED THE RETURN OF THE AMOUNT OF THE PUR-
CHASE PRICE PAID BY PURCHASER AND UNDER NO CIRCUMSTANCES
SHALL BOXLIGHT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSE-
QUENTIAL DAMAGES OR LOST PROFITS, LOST REVENUES OR LOST SAVINGS.
THE PRICE STATED FOR THE PRODUCT IS A CONSIDERATION IN LIMITING
BOXLIGHT’S LIABIL-ITY. NO ACTION, REGARDLESS OF FORM, ARISING OUT OF
THE AGREEMENT TO PURCHASE THE PRODUCT MAY BE BROUGHT BY PUR-
CHASER MORE THAN ONE YEAR AFTER THE CAUSE OF ACTION HAS
ACCRUED. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION
OF INCIDENTAL OR CONSEQUENTIAL DAM-AGES SO THE ABOVE LIMITA-
TION OR EXCLUSION MAY NOT APPLY TO YOU. THIS LIMITED WARRANTY
GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER
RIGHTS WHICH VARY FROM STATE TO STATE.
WARRANTY LIMITATION AND EXCLUSION
BOXLIGHT shall have no further obligation under the foregoing limited warranty if the
Product has been damaged due to abuse, misuse, neglect, accident, unusual physical
or electrical stress (unusual physical and electrical stress includes unusually long
operation, exposure to smoke and other airborne contaminants), unauthorized modi-
fications, tampering, alterations, or service other than by BOXLIGHT or its authorized
agents, causes other than from ordinary use or failure to properly use the Product in
the application for which said Product is intended.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
CD-850m
Boxlight
19332 Powder Hill Place
Poulsbo, WA 98370-7407 USA
U.S.A. and Canada 800-762-5757
International 360-779-7901
™
BOXLIGHT
CORPORATION
Download from Www.Somanuals.com. All Manuals Search And Download.
|