R 9849999
INSTALLATION MANUAL
Ceiling Mount for CLM series projector
Date 26/11/07
Rev: 00
Art. No.: R 59770182
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety guidelines
WHO
This installation manual must be performed by authorized technical personnel
only.
WARNING
The ceiling should be capable of supporting a weight of at least 5 times the total
weight of the Ceiling Mount and Projector (i.e. at least 160 kg or 353LB). If it
cannot, the ceiling must be reinforced. Improper installation may result in serious
personal injury.
Consult a professional structural engineer prior to suspending the Ceiling Mount
from a structure not intended for that use.
Always ensure the working load limit of the structure supporting the Ceiling Mount.
CAUTION
Installing the Ceiling Mount should be performed only after you are thoroughly
familiar with all of the following safety checks and installation instructions.
To do otherwise increases the risk of hazards and injury to the user.
This support is designed for intended use only with Barco CLM series projectors. It
supports maximum 33 kg or 73LB. Use with any other appliance/projector may
result in instability causing possible injury.
Do not modify and/or replicate any component. Barco n.v. uses specific materials
and manufacturing processes in order to achieve part strength. Consult Barco nv
for assistance with custom applications.
Always follow Barco installation instructions. Contact Barco n.v. if you should have
any question regarding the safety of an application.
PRODUCT CARE
Ceiling Mount components should be kept dry, clean, lubricated (if required),
coated properly, and otherwise maintained in a manner consistent with part
design. Barco products must be used in a manner consistent with their design and
inspected on a routine basis for security, wear, deformation, corrosion and any
other circumstances that may affect the load handling capability of the part.
Barco n.v. recommends inspections at least once a year for all installations and
increasing in frequency for more critical installations. If the part is found to have
damage, which may cause a decrease in load capability, the part must be removed
from service immediately.
Under no circumstances are Barco parts repariable by anyone other than Barco
n.v.
Download from Www.Somanuals.com. All Manuals Search And Download.
Description and Contents of the kit
Purpose of the Kit
The kit is designed for the CLM CM R10 series projectors and allows the
projector to be mounted to the ceiling.
Contents of the Kit
Following items are included:
• Kit R9849999: Ceiling mount
• Installation manual : R59770182
• Mounting bracket and Screws: R835785 Qty 3 Nos and R 826743 qty 1
No, - --
• Safety Chain set : B361213 Qty 1 Nos , A577535 qty 1 Nos, A566050 qty
1 nos and B363509 qty 2 nos
• Cable cover assy
Illustration of the ceiling mount
R826743
R835786
R83578
Download from Www.Somanuals.com. All Manuals Search And Download.
Remark:
The ceiling mount can also be mounted using one of the 2 available bars (height
adjustment) and cable cover assy.
R9841260: short bar R822922 and cable cover assy .
min length = 445mm(17.52 inch)
max length = 810 mm(31.89 inch)
R9841261: long bar R822923 cable cover kit R984 .
min length = 845mm(33.27 inch)
max length = 1210 mm(47.64 inch)
I
llustration of the Cable Cover Assy:
R826748
R826761
G229790 &
V3675126
R826749
R347968 (7X)
Z348001( 4X)
R826745
R347972 ( 4 X)
Note: The assembly is used only when ceiling mount is mounted along with
IQ bar for hiding and guiding the cables.
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the Assembly
Necessary Tools
1. Torx screw driver for M3 screw
2. Hexagonal driver (n° 6)
3. Ring spanner 12-13mm
4. Side spanner 12-13mm
5. Cross head screw driver for M8 screw
Centering the ceiling mount
Mark the position on the ceiling hole. Since the center of the lens does not
coincide with the center of the projector, the center of the lens has been marked
on the ceiling mount.
Remark
The horizontal shift of the ceiling mount allows to re-enter the projector later on,
However, centering decently the base plate insures a good horizontal shift
margin afterwards.
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the Assembly
The fixation can be done with standard M8 bolt (not supplied)
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector preparation
1. Turn the projector to its back and remove the Feet assembly. Unscrew 3
Plastic feet and remove their Allen head M10 screws. Discard 3 plastic feet
r852944 and x head M10 screw.
R852944, R852945
& A566050 M10
SCREW, & FEET
SUPPORT
2. Fix the Spacer M10 (r835785) as shown below. For alignment of the Centre
distance between the spacers fix the ceiling mount and fix nut M8 B360623,
Do not tight fully then tight the spacer M10. Remove the Ceiling mount and
fix it on the Ceiling.
Washer , Spacer
M10 R835785 and
Flange Nut M8
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Lift and slide the projector assembly into the Ceiling mount. The projector will
be located precisely into the ceiling mount base plate after the tightening of 3
M 8 flange Nuts (b360623).
Slide
Lift
4. Route the Signal cables and Power cord into the cable saddles.
5. Take care of the orientation of safety chain bracket.
6. Fix the one end of safety chain into the projector’s chain bracket with the help
of the snap hook and the other end to the firm place in the Ceiling.
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjustments
Following adjustment can be done in random order.
A
Shift parallel to
screen
C
Up/down
B 4no’s
(2 in opposite
side)
Rotate around central
Axis ±3°
1. Shift parallel to the screen
Loosen the 2 bolts A and move the projector till the projector is aligned.
Tighten these 2 bolts to secure the position.
2. Up down Tilt
Loosen the 4 bolts B . Adjust the up/down tilt precisely by moving bolt C
clockwise or anti clockwise . Tighten the 4 bolts B to secure the position.
Download from Www.Somanuals.com. All Manuals Search And Download.
Rotate around
E
vertical axis ±5°
F
F
Rotate around central
Axis ±3°
G
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Rotate around central Vertical axis
Loosen the 4 bolts E . Rotate/adjust the projector clockwise or anti clockwise.
Tighten the 4 bolts E to secure the position.
4. Rotate around central Horizontal axis
Loosen the 4 bolts F . Adjust the motion precisely by moving bolt G clockwise
or anti clockwise. Tighten the 4 bolts F to secure the position.
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the bar with Cable Cover assembly
1. Unscrew the 2 bolts J and slide out the upper part of the Bar. Pass the cable
cover into the upper part of the Bar
2. Slide the horizontal shift plate R 826743 into the lower part of the Bar. Fix with
4 M8 bolt K.
3. Slide the upper bar into the lower bar assembly. Remount the 2 previously
removed bolt J. Adjust the height to minimum.
K
J
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Routing the Cables
a. RGBHV cable preparation: With the help of PVC tape arrange the
connectors in series. Pass the Signal cables and Power cord into cable
guide R826761
.
b. Pass the Signal cables into the IQ bar assembly from top side. Take out
the BNC connector (in case of a 5 BNC cable) one by one from bottom
side.
Download from Www.Somanuals.com. All Manuals Search And Download.
c. Pass the Power cord and the other cables (if any) one by one.
d. Pass all the cables one by one from cable guide R 826745 and fix the
cable guide on to the horizontal shift plate using 2 M3 Screws L.
The cable routing through IQ bar is complete. Adjust the approximate
height of the IQ bar and also adjust the length of the cable required at the
projector side.
5. Mount the Ceiling Bracket R 826748 on to the ceiling with standard M8 bolt
not supplied with the Kit. For marking of the ceiling holes, refer the Installation
manual of the Ceiling Mount of CV 120 (R5973715)
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Hang on the IQ bar and cable routed assembly. Fix with 4 M8 bolt along with
washer M.
M
7. Mount the Ceiling mount assembly on to the horizontal shift plate by twisting
and then lifting up. Fix the 2 M8 Bolt A.
A
8. Route the Power cord to the back and Signal cables to the front.
Download from Www.Somanuals.com. All Manuals Search And Download.
There is also an option to route the cable from inside the Ceiling mount using
cable ties and guiding holes on the Ceiling mount base as shown below.
Cable Ties
RGB cables
Power cord &
other cables
Cable Tie
Break the cable guide grooves on the cable cover as per the direction and
location of the input cables and power cord at customer site/room. Lift the
cable cover and fix with the help 4 M3 screws N
Cable
guide
N
Cable Guide
Grooves
Download from Www.Somanuals.com. All Manuals Search And Download.
9. The adjustment procedure for the rotation around central vertical axis can
also be done as explained below.
Loosen the 4 M3 screws N of cable cover and slide it down word.
Loosen the 4 bolts O. Rotate /adjust the projector clockwise or anti
clockwise. Tighten the 4 bolts O to secure the position. Slide up the
cable cover and fix 4 M3 screws N.
O
O
Rotate around
R83578
5
10.fix the one end of safety chain into the projector’s Eye bolt and the other
end to the firm place in the ceiling.
Download from Www.Somanuals.com. All Manuals Search And Download.
|