Product Description
Model EIR505-xx
Documentation Number: EIR505-xx_5107m
707 Dayton Road -- P.O. Box 1040 -- Ottawa, IL 61350 USA
Phone (815) 433-5100 -- General Fax (815) 433-5105
Phone (815) 433-5100 -- General Fax (815) 433-5105
Website: www.bb-elec.com
European Headquarters
B&B Electronics
Westlink Commercial Park -- Oranmore, Co. Galway, Ireland
Phone +353 91-792444 -- Fax +353 91-792445
Website: www.bb-europe.com
B&B Electronics Mfg. Co. Inc. -- December 2007
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Five Port Managed Industrial
Ethernet Switches
User Manual
Manual Documentation Number: EIR505-xx_5107m
Table of Contents
iii
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Notice
The contents of this manual are based on the firmware, kernel, and
hardware versions listed below.
Firmware Version
V1.29
V2.05
A5.00
Kernel Version
Hardware Version
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Warning
This Equipment has been tested and found to comply with the limits for a
Class-A digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
„
„
„
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
„
Consult the dealer or an experienced radio/TV technician for help.
CE Mark Warning
This is a Class-A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
Manual Documentation Number: EIR505-xx_5107m
Table of Contents
v
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Content
FCC Warning............................................................ v
CE Mark Warning..................................................... v
Introduction................................................................ 1
Features ................................................................... 1
Package Contents.................................................... 2
Hardware Description................................................ 3
Physical Dimension.................................................. 3
Front Panel............................................................... 3
Reset Button.......................................................................3
Bottom View............................................................. 4
DIP-switch ................................................................ 4
LED Indicators.......................................................... 5
Ports......................................................................... 6
Cabling ..................................................................... 8
Wiring the Power Inputs ........................................... 9
Wiring the Fault Alarm Contact ................................ 9
Wiring the Fault Alarm Contact .............................. 10
Mounting Installation............................................... 11
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
DIN-Rail Mounting.................................................. 11
Wall Mount Plate Mounting .................................... 13
Hardware Installation............................................... 14
Network Application................................................ 15
X-Ring Application.................................................. 15
Coupling Ring Application...................................... 16
Dual Homing Application........................................ 17
Web-Based Management ........................................ 18
About Web-based Management ............................ 18
Preparing for Web Management............................ 18
System Login.......................................................... 19
Port status .............................................................. 19
Port status .............................................................. 20
Single Port Information.....................................................20
Port Statistics ......................................................... 21
Port Control ............................................................ 22
Switch Settings....................................................... 23
Port Mirroring.......................................................... 24
VLAN configuration ................................................ 25
Manual Documentation Number: EIR505-xx_5107M
Table of Contents
vii
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Port-based VLAN .............................................................25
802.1Q VLAN ...................................................................27
IP Address.............................................................. 31
SNTP Configuration ............................................... 32
IP Security.............................................................. 35
RSTP Configuration ............................................... 36
System Configuration.......................................................36
Per Port Configuration......................................................38
X-Ring .................................................................... 39
QoS Configuration.................................................. 41
IGMP ...................................................................... 43
Security Manager ................................................... 45
Configuration Backup............................................. 45
TFTP Restore Configuration.............................................45
TFTP Backup Configuration .............................................46
TFTP Update Firmware.......................................... 46
Factory Default....................................................... 47
System Reboot....................................................... 47
Save Configuration................................................. 48
Rate Control ........................................................... 48
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubles shooting.................................................... 50
Technical Specification........................................... 51
Manual Documentation Number: EIR505-xx_5107M
Table of Contents
ix
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
The Elinx EIR505 series of Industrial Managed Ethernet Switches provide
powerful functionality in a small package. Designed for industrial
applications, these switches are highly reliable.
Features
„
„
Conforms to IEEE 802.3 10Base-T, 802.3u 100Base-TX/100Base-FX
5-port 10/100TX industrial switch (Fiber Optic models have 1 100FX
port)
„
„
„
„
„
„
„
RJ-45 ports support auto MDI/MDI-X
Store-and-Forward switching architecture
Wide-range redundant input power connections
DIN rail and panel mount design
Easy to configure
Web based management
IEEE 802.1p class of service and port based, Tag based, and Type of
service priority method
„
„
„
„
„
„
„
„
„
Each port supports 4 priority queues
Port based VLAN / 802.1 Q Tag VLAN
IGMP with Query mode for multi media application
DHCP client
Ingress packet filter and egress rate limit.
Relay alarm output for system events
Input power reverse polarity protection
Port mirror for TX only, TX and RX packet
IEEE 802.3x flow control
¾
¾
Flow control with full-duplex
Back pressure with half-duplex
„
„
„
„
„
X-Ring function
SNTP
TFTP firmware update, system configuration restore and backup
1Mbits Embedded memory
2K MAC address table
Manual Documentation Number: EIR505-xx_5107m
1
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Package Contents
„
„
„
„
5 Port Managed Industrial Switch
One DIN-Rail (attached to the switch)
One Panel mount plate and six screws
User manual
5 10/100TX with X-Ring Web Management
Industrial switch
User Manual
Wall Mount Plate
Screws
DIN-Rail
If any item is missing or damaged, contact B&B
Electronics for a replacement.
2
Manual Documentation Number: EIR505-xx_5107m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Description
Physical Dimension
(W x H x D) 2.13in x 5.31in x 4.13 in (54mm x 135mm x 105mm)
Front Panel
EIR505 Front Panel
Reset Button
The reset button is used to restart the reboot the switch or restore it to the
factory default configuration.
„
„
Restart: Press the button for 2 seconds and release.
Set to factory default value: Press the button for 5 seconds and
release.
Manual Documentation Number: EIR505-xx_5107m
3
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Bottom View
The bottom panel of the EIR-505-xx industrial switch consists of one
terminal block connector with two DC power inputs and one DC IN power
jack.
Bottom Panel of the industrial switch
DIP-switch
The six position DIP-switch is used to configure the relay alarm operation
mode and the master ring operation mode. The default value for each
position is OFF.
DIP Switch No
Status
Description
OFF
Disable port 1 Alarm
1
2
ON
Enable port Alarm.
Disable port Alarm
OFF
4
Manual Documentation Number: EIR505-xx_5107m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
ON
Enable port Alarm.
OFF
ON
Disable port Alarm
Enable port Alarm.
Disable port Alarm
Enable port Alarm.
Disable port Alarm
3
4
OFF
ON
OFF
5
ON
Enable port Alarm.
OFF
ON
Disable the master ring function.
6
Enable the switch as the ring master
in the X-Ring group.
LED Indicators
There are 7 diagnostic LEDs located on the front panel. They provide
real-time status information.
LED
Status
Meaning
Power
Green
The switch is on
Manual Documentation Number: EIR505-xx_5107m
5
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
The switch is off or no power input
is available
Off
The switch is the master of X-Ring
group
Green
Off
R.M. (Ring Master)
The industrial switch is not the
master of an X-Ring group
Green
Off
Power source 1 is available
Power source 1 is not available
Power source 2 is available
Power source 2 is not available
Power failure or port failure
Normal Operation
Power 1
Power 2
Fault
Green
Off
Yellow
Off
Green
The port is linked
LNK/ACT (port 5)
Blinking
Off
The port is transmitting or receiving
No device attached
RJ-45 or Fiber Optic
The port is operating in full-duplex
mode
Yellow
Blinking
Off
FDX/COL (port 5)
Data Packet Collision
RJ-45 or Fiber Optic
The port in half-duplex mode or is
not connected to a device
Ports
„
RJ-45 ports
There are 5x 10/100Mbps auto-sensing ports for 10Base-T or 100Base-TX
device connection. The ports are auto-sensing and auto MDI/MDIX.
6
Manual Documentation Number: EIR505-xx_5107m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
RJ-45 Pin Assignments
Pin Number
Assignment
1
2
3
6
Tx+
Tx-
Rx+
Rx-
All ports on this switch support automatic MDI/MDI-X operation.
Straight-through cables can be used for all network connections. In
straight-through cable, pins 1, 2, 3, and 6, at one end of the cable, are
connected straight through to pins 1, 2, 3 and 6 at the other end of the cable.
The table below shows the 10BASE-T/100BASE-TX MDI and MDI-X port
pin outs.
Pin MDI-X
Signal Name
MDI Signal Name
1
2
3
6
Receive Data plus (RD+)
Transmit Data plus (TD+)
Receive Data minus (RD-) Transmit Data minus (TD-)
Transmit Data plus (TD+) Receive Data plus (RD+)
Transmit Data minus (TD-) Receive Data minus (RD-)
Straight Through Cable Schematic
Manual Documentation Number: EIR505-xx_5107m
7
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Cross Over Cable Schematic
„
Fiber Port
There is one 100Base-FX port. The fiber port is SC type connector in multi
mode (2Km) or single mode (30Km).
Connect the fiber port as described below.
ATTENTION
This is a Class 1 Laser/LED product. Do not stare into
the Laser/LED Beam.
Cabling
„
„
Use Category 5 cabling for RJ-45 port connections. The cable must
be less than 328 ft (100 meters) long.
Use 8/125 or 9/125 um for single-mode fiber. Distances up to 30
8
Manual Documentation Number: EIR505-xx_5107m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Kilometers are supported.
„
Fuse 50 or 62.5/125 um for multi-mode fiber cable. Distances up to
2Kmare supported.
Wiring the Power Inputs
V- V+
V- V+
1. Insert the positive and negative wires into the V+ and V-
connector on the terminal block connector
2. Tighten the wire-clamp screws
[NOTE] Use 12~ 24 AWG wire.
Manual Documentation Number: EIR505-xx_5107m
9
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Wiring the Fault Alarm Contact
The fault alarm contact are located in the middle of terminal block connector
as shown below. Insert the wires and set the Dipswitch to “ON”. When a
power source fails or a link fault occurs, it will be detected and cause an
open circuit. The following figure shows an application example for the fault
alarm contact.
1A@24V
Insert the wires into the fault alarm contact
[NOTE] The wire range of terminal block is from 12~ +24 AWG.
Fault Alarm Contact
The open circuit will form when the
power failure or port link failure.
24V DC Buzzer
24V Battery
The fault alarm device will send a
warning signal to warn the user, ex:
alarm sound or flash light.
10
Manual Documentation Number: EIR505-xx_5107m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting Installation
DIN-Rail Mounting
Rear Panel of
the switch
DIN-Rail
„
„
Use the screws to attach the DIN-Rail to the industrial
switch
To remove the DIN-Rail, reverse the step 1.
Manual Documentation Number: EIR505-xx_5107m
11
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
1. First, insert the top of DIN-Rail into the track.
2. Then, lightly push the DIN-Rail into the track.
3. Ensure the DIN-Rail is tightly secured to the track.
4. To remove the industrial switch from the track, reverse steps above.
12
Manual Documentation Number: EIR505-xx_5107m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Panel Mounting
Follow the steps below to mount the industrial switch with the Panel mount
plate.
1. Remove the DIN-Rail from the industrial switch.
2. Place the wall Panel plate on the rear of the industrial switch.
3. Use the screws to attach the Panel plate to the industrial switch
4. Use the hook holes at the corners of the panel mount plate to attach the
industrial switch to the panel.
5. To remove the panel mount plate, reverse steps above
Manual Documentation Number: EIR505-xx_5107m
13
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
.
1. Unpack the Industrial switch.
2. Ensure the DIN-Rail is tightly screwed to the Industrial switch. If not,
refer to DIN-Rail Mounting section for DIN-Rail installation. To panel
mount the Industrial switch, refer to Panel Mounting section.
3. Apply power to the switch (refer to the Wiring the Power Inputs
section). The power LED will light.
4. Connect CAT 5 cables to the Industrial switch’s RJ-45 ports and to the
network devices.
[NOTE] If the network devices do not support MID/MDIX, a
crossover cable may be required.
5. Connect the fiber optic cables to the industrial switch and network device.
Ensure that the switch’s fiber optic transmitter is connected to the
network devices receiver and vice versa.
6. When all the connections are made and the LEDs show normal
indications, the installation is complete.
14
Manual Documentation Number: EIR505-xx_5107m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Network Application
X-Ring Application
The EIR505 series of Industrial Switches incorporate the X-Ring Protocol to
ensure network reliability and system restoration within 300 ms in the event
of a connection failure. The X-Ring algorithm is similar to the spanning tree
protocol (STP) algorithm but it has faster recovery time. The following figure
below is an example of an X-Ring application.
Manual Documentation Number: EIR505-xx_5107m
15
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Coupling Ring Application
If the network has more than one X-Ring group, the coupling ring function is
used to connect them and add redundancy. This ensures that transmissions
between the two ring groups will not fail. The figure below is an example of
the coupling ring application.
16
Manual Documentation Number: EIR505-xx_5107m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Dual Homing Application
The Dual Homing function is used to prevent a connection loss between the
X-Ring group and the upper level/core switch. Assign a port in each X-ring
group to be the Dual Homing ports The Dual Homing function can only be
used when the X-Ring function is active. Each X-Ring group can have one
Dual Homing port.
[NOTE] In the Dual Homing architecture, the upper level switches must
have Rapid Spanning Tree protocol enabled.
Manual Documentation Number: EIR505-xx_5107m
17
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Web-Based Management
About Web-based Management
The switch has an embedded HTML web site residing in flash memory. This
site offers advanced management features and allows the switch to be
configured from anywhere on the network.
The web site is designed for Internet Explorer 5.0 and uses Java Applets to
reduce bandwidth consumption, enhance access speed, and present an
intuitive user interface.
[NOTE] By default, IE5.0 and later versions do not allow Java Applets to
activate sockets. The user must modify the browser setting to enable Java
Applets to operate network ports.
Preparing for Web Management
Before using web management, install the industrial switch on the network
and verify that a PC on the local network can connect with the switch
through the web browser. The default IP Address, Subnet Mask, Username
and Password is listed below:
„
„
„
„
„
IP Address: 192.168.16.1
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.16.254
User Name: root
Password: root
18
Manual Documentation Number: EIR505-xx_5107m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
System Login
1. Launch Internet Explorer on the PC.
and then Press “Enter”.
3. The login screen will appear.
4. Enter the user name and password.
5. Press “Enter” or “OK”, the home screen will appear.
Function Menu Bar
Home Interface
Panel Figure Display
Configuration Display Screen
Manual Documentation Number: EIR505-xx_5107m
19
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Port status
Shows the status of each port
„
„
„
„
Port: Displays the port number
Type: Displays the speed and mode, ex: 100TX = 100Mbps
Link: Displays the ports status (up or down)
State: Displays the ports status (disabled or enabled). Unlinked is
displayed as “off ”
„
„
Negotiation: Displays the auto negotiation mode (auto or forced).
Speed Duplex: Displays the port connection speed. “Config” is the
configured value. “Actual” is the current value.
„
Flow Control: Displays the flow control status as “Symmetric” or
“Asymmetric” in full mode. “Disable” means that flow control is not
enabled “Config” indicates that the value is user configured. “Actual” is
the current value of the port.
Port Status interface
Single Port Information
Click the desired port on the Panel figure. The single port information
window will display the current port information.
20
Manual Documentation Number: EIR505-xx_5107m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Port information interface
Port Statistics
Clear
Displays port statistics. Click
button to reset.
Port Statistics Interface
Manual Documentation Number: EIR505-xx_5107m
21
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Port Control
Used to set up the port.
1. Select the port by scrolling down the Port column. The current port
information will be displayed in the table below.
2. State: Enables or disables the port.
3. Negotiation: Sets the negotiation mode to Auto, Nway (specify the
speed/duplex of the port and enable auto-negotiation), or Forced.
4. Speed: Sets the transmit speed of the port
5. Duplex: Sets the port to full-duplex or half-duplex
6. Flow control: Sets flow control function to Symmetric or Asymmetric
in Full Duplex mode(The default value is Disable)
Apply
7. Click the
button to apply configurations
8. Select the port again to verity the configuration.
[NOTE] If the configuration is not saved it will be lost when the switch
is powered off.
Port Control interface
22
Manual Documentation Number: EIR505-xx_5107m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Switch Settings
Used to assign the system name, location and to view system information
„
„
„
System Name: Assigns a name to the switch. The maximum length is
64 bytes
System Location: Assigns a physical location for the switch. The
maximum length is 64 bytes
System Description: Displays the description of switch. This is read
only and cannot be modified
„
„
„
„
Firmware Version: Displays the firmware version
Kernel Version: Displays the kernel software version
Hardware version: Display the hardware version
MAC Address: Display the unique hardware address assigned by
manufacturer (this value is different for each switch)
Switch settings interface
[NOTE] If the configuration is not saved, it will be lost when the switch
is powered off.
[NOTE] The Firmware, Hardware, and Kernel versions listed above are
current as of the date this manual was produced.
Manual Documentation Number: EIR505-xx_5107m
23
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Port Mirroring
Port mirroring is a method to monitor traffic in switched networks. This is
accomplished by mirroring the traffic going in and out of the monitored ports
to a specifically designated port (the mirror port).
1. Port Mirroring Mode: Sets the mirror mode. Select disable to disable
port mirroring. Select TX to monitor data being transmitted by a port.
Select both to monitor port data being transmitted and received by a
port. The default value is “Disable”.
2. Analysis Port: This is the port used to see all monitored port traffic
(This port can be connected to a LAN analyzer or Netxray).
3. Monitor Port: Check the box to monitor the port. Up to 4 ports can be
designated as monitor ports.
[NOTE]
If the configuration is not saved, it will be lost when the port is
powered off.
Port Mirroring interface
24
Manual Documentation Number: EIR505-xx_5107m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
VLAN configuration
A Virtual LAN (VLAN) can be thought of as a broadcast domain that exists
within a switch or a defined set of switches. By grouping switch ports into
VLANs, traffic flooding is limited since devices can only communicate
directly with devices belonging to the VLAN. Creating a VLAN from a switch
is the logical equivalent of reconnecting a group of devices to another Layer
2 switch. However, the network devices retain their same physical
connection. The EIR505 series switches support port-based and 802.1Q
(tagged-based) VLAN. In the default configuration, the VLAN option is
disabled.
VLAN Configuration interface
Port-based VLAN
With port-based VLAN, the port is assigned to a VLAN. Therefore all
devices attached to a given port should be members of the same VLAN. As
with other VLAN configurations, the packets forwarded using this method do
not leak into other VLAN domains on the network. After the port has been
assigned to a VLAN, devices on the port cannot send to or receive from
devices in other VLANs without the intervention of another layer 3 device or
the ability to tag the data packet with a specific PVID.
Manual Documentation Number: EIR505-xx_5107m
25
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
VLAN – Port Base interface
Add
1. Click
to add a new VLAN group. The EIR505 series supports up
to 64 VLAN groups
2. Enter Group name, VLAN ID and select the members of VLAN group
Apply
3. Click
26
Manual Documentation Number: EIR505-xx_5107m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
VLAN—Port Base Add interface
4. The VLAN group will be displayed after apply is clicked
Next Page
5. Click
6. Use
7. Use
to view the next VLAN group
button to delete unwanted VLANs
button to modify existing VLANs
Delete
Edit
[NOTE] If the configuration is not saved, it will be lost when the switch
is powered off
802.1Q VLAN
Tagged-based VLAN is an IEEE 802.1Q specification which allows VLANs
to be created across devices from different venders. IEEE 802.1Q VLAN
Manual Documentation Number: EIR505-xx_5107m
27
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
uses a technique to insert a “tag” into the Ethernet frame. The tag contains a
VLAN Identifier (VID).
When the 802.1Q VLAN is enabled, all ports on the switch belong to a
default VLAN (VID 1). The default VLAN can’t be deled. The EIR505 series
will support up to 64 VLAN groups.
802.1q VLAN interface
„
Basic
Add
1. Click
2. Management VLAN ID:
Used for Remote Management Security.
When this option is selected, remote management is only available to
the members of the indicated VLAN Group. Enter the specific VLAN ID
number in Management VLAN ID column, check the box, and click the
Apply
button. Example: If the management VLAN ID is 101 and the
VLAN group ID 101 includes ports 1, 2, and 4, only ports 1, 2, and 4
can perform remote management functions on the switch. If a port is in
multiple VLAN groups, it can still perform management functions as
long as one VLAN group ID is equal to the Management VLAN ID.
28
Manual Documentation Number: EIR505-xx_5107m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Group Name: assign a name for the new VLAN
4. VLAN ID: fill in a VLAN ID. The default is 1
5. From the Available ports box, select ports to add to the VLAN group
Add
and click
button
802.1q VLAN –Add interface
Next
6. Click
to bring up the configuration interface:
Manual Documentation Number: EIR505-xx_5107m
29
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Select outgoing frames as VLAN-Tagged frames or untagged and then
Apply
click
„
Configure port VID settings
Port VID:
1. Port VLAN ID: enter the port VLAN ID
Apply
2. And then, click
Default
3. To reset to the default values, click
button
30
Manual Documentation Number: EIR505-xx_5107m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
802.1q VLAN – Port VLAN ID interface
[NOTE] If the configuration is not saved, it will be lost if the switch is
powered off.
IP Address
Configure the IP Settings and DHCP client function
„
DHCP Client: Use to enable or disable the DHCP client function. When
the DHCP client function is enabled, the industrial switch will be
assigned an IP address from the network DHCP server. After the
“Apply” button is clicked, dialog box will indicate that the user that when
the DHCP client is enabled, the current IP will lost and the new IP must
be looked up on the DHCP server. The switch’s MAC Address will be
required to look up the new IP Address on the DHCP Server. To cancel
the DHCP client function, click “cancel”.
„
IP Address: Assign a static IP address. This is not required if DHCP
Manual Documentation Number: EIR505-xx_5107m
31
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Client is enabled. The default IP is 192.168.10.1.
Subnet Mask: Assign the subnet mask of the IP address. This is not
required if the DHCP Client is enabled.
„
„
Gateway: Assign the network gateway. The default gateway is
192.168.10.254.
Apply
„
Click
IP configuration interface
SNTP Configuration
SNTP (Simple Network Time Protocol) allows the switch to synchronize its
time with an SNTP Server.
1. SNTP Client: Enable or Disable SNTP
2. Daylight Saving Time: Enables or disables daylight saving time. When
enabled, the daylight saving time period must be entered.
3. UTC Time zone: Used to calculate local time. Set the switch location
time zone.
Local Time Zone
Conversion from UTC
Time at 12:00 UTC
November Time
Zone
- 1 hour
-2 hours
11am
Oscar Time Zone
10 am
32
Manual Documentation Number: EIR505-xx_5107m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
ADT - Atlantic
Daylight
-3 hours
-4 hours
9 am
8 am
AST - Atlantic
Standard
EDT - Eastern
Daylight
EST - Eastern
Standard
-5 hours
-6 hours
-7 hours
7 am
6 am
5 am
CDT - Central
Daylight
CST - Central
Standard
MDT - Mountain
Daylight
MST - Mountain
Standard
PDT - Pacific
Daylight
PST - Pacific
Standard
-8 hours
-9 hours
4 am
3 am
ADT - Alaskan
Daylight
ALA - Alaskan
Standard
HAW - Hawaiian
Standard
-10 hours
-11 hours
2 am
1 am
Nome, Alaska
CET - Central
European
FWT - French Winter
MET - Middle
European
+1 hour
1 pm
MEWT - Middle
Manual Documentation Number: EIR505-xx_5107m
33
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
European Winter
SWT - Swedish
Winter
EET - Eastern
European, Russia
Zone 1
+2 hours
+3 hours
2 pm
3 pm
BT - Baghdad,
USSR Zone 2
ZP4 - Russia Zone 3
ZP5 - Russia Zone 4
ZP6 - Russia Zone 5
WAST - West
Australian Standard
CCT - China Coast,
USSR Zone 7
JST - Japan
+4 hours
+5 hours
+6 hours
4 pm
5 pm
6 pm
+7 hours
+8 hours
7 pm
8 pm
Standard, Russia
Zone 8
+9 hours
9 pm
EAST - East
Australian Standard
GST
+10 hours
10 pm
Guam Standard,
Russia Zone 9
IDLE - International
Date Line
NZST - New
+12 hours
Midnight
Zealand Standard
NZT - New Zealand
4. SNTP Sever IP: Enter the IP address of the SNTP server.
5. Switch Timer: Displays the switch’s current time
6. Daylight Saving Period: Enter the daylight saving time period
7. Daylight Saving Offset (mins): Configuring the offset value in minutes
Apply
8. Click
to active the configuration
34
Manual Documentation Number: EIR505-xx_5107m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
[NOTE] If the configuration is not saved, it will be lost when the switch
is powered off.
SNTP Configuration
IP Security
IP security function grants 10 specific IP addresses permission to access
the switch through a web browser for the switch management.
1. Enable the IP Security: Mark the check box to enable
2. Security IP 1 ~ 10: Enter up to 10 specific IP address.
Apply
3. Click
[NOTE] If the configuration is not saved, it will be lost when the switch
is powered off.
Manual Documentation Number: EIR505-xx_5107m
35
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
IP Security Interface
RSTP Configuration
The Rapid Spanning Tree Protocol (RSTP) is an evolution of Spanning Tree
Protocol (STP). It provides a faster spanning tree convergence after a
topology change. The switch will auto detect a device that is running STP or
RSTP protocol.
System Configuration
Modify RSTP state parameters
„
„
RSTP mode: Enable or disable RSTP function.
Priority (0-61440): a value used to identify the root bridge. The bridge
with the lowest value has the highest priority and is selected as the root.
If the value changes, the switch must be rebooted. The priority value
must be multiple of 4096 according to the protocol standard rule.
Max Age (6-40): the number of seconds a bridge waits without
receiving Spanning-tree Protocol configuration messages before
attempting a reconfiguration. Enter a value between 6 and 40.
Manual Documentation Number: EIR505-xx_5107m
„
36
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
„
„
Hello Time (1-10): The time that the control switch sends out a BPDU
packet to check RSTP status. Enter a value between 1 and 10.
Forward Delay Time (4-30): The number of seconds a port waits
before changing from its Rapid Spanning-Tree Protocol learning and
listening states to the forwarding state. Enter a value between 4
through 30.
Apply
„
Click
[NOTE]
1. Use the following rule to configure the MAX Age, Hello Time,
and Forward Delay Time.
2 x (Forward Delay Time value –1) > = Max Age value >= 2
x (Hello Time value +1)
If the configuration is not saved it will be lost when the switch
is powered off.
RSTP– System Configuration Interface
Manual Documentation Number: EIR505-xx_5107m
37
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Per Port Configuration
Configure path cost and priority of every port
1. Select the port in Port column
2. Path Cost: The cost of the path to the other bridge from this transmitting
bridge at the specified port. Enter a number 1 through 200000000
3. Priority: Network Priority. Enter a number from 0 to 240. The value must
be a multiple of 16
4. Admin P2P: Some of the rapid state transactions that are possible
within RSTP are dependent upon whether the port concerned can only
be connected to one other bridge (i.e. it is served by a point-to-point LAN
segment), or whether it can be connected to two or more bridges (i.e. it
is served by a shared medium LAN segment). This function allows the
P2P status of the link to be manipulated administratively. True is P2P
enabling. False is P2P disabling
5. Admin Edge: The port directly connected to end stations cannot create
a bridging loop. To configure the port as an edge port, set the port to
“True” status
6. Admin Non Stp: The port includes the STP mathematic calculation.
True does not include the STP mathematic calculation. False includes
the STP mathematic calculation
Apply
7. Click
[NOTE] If the configuration is not saved, it will be lost when the switch
is powered off.
38
Manual Documentation Number: EIR505-xx_5107m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
RSTP – Per Port Configuration interface
X-Ring
X-Ring provides network redundancy similar to the Spanning Tree and
Rapid Spanning Tree Protocols. However, recovery time is greatly reduced
when the X-Ring protocol is used. The protocol identifies one switch as the
Ring Master. Packets are blocked from the redundant path unless a ring
member becomes disconnected from the rest of the network. When this
happens, the protocol automatically restores connectivity using the
redundant path.
In the X-Ring topology, every switch should enable X-Ring function and
assign two member ports to the ring. Only one switch in the X-Ring group
would be set as the backup switch. Other switches are called working
switches and their two member ports are called working ports. If a network
connection failure occurs, the backup port will automatically become a
working port to recover.
The switch has a Dipswitch to configure the switch as the ring master. The
Manual Documentation Number: EIR505-xx_5107m
39
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
ring master has the rights to negotiate and place a command to other
switches in the X-Ring group. If more than one switch is in master mode,
the software will select the switch with lowest MAC address number as the
ring master. An LED on the front panel indicates that the switch is the ring
master.
Coupling ring is used to connect 2 or more X-Ring groups providing a
redundant back-up Dual homing is used to recover from a connection loss
between an X-Ring group and the upper level/core switch.
„
„
Enable X-Ring: Mark the check box to enable the X-Ring function
1st & 2nd Working Ports: Assign two ports as the member ports. One
port will be working port and one port will be the backup port. The
system will automatically decide which port is working port and which
port is backup port
„
Enable Coupling Ring: Mark the check box to enable the coupling
ring function
„
„
Coupling port: Assign the member port
X-Ring Master: Set the switch labeled RM on front panel to on position.
This establishes that switch as a master for the ring.
Enable Dual Homing: Set up one of port to be the Dual Homing port.
In an X-Ring group, only one can be a Dual Homing port. This function
will only work when the X-Ring function is enabled
„
„
Apply
Click
40
Manual Documentation Number: EIR505-xx_5107m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
X-Ring Interface
[NOTE]
1. When the X-Ring function is enabled, the RSTP function must be
disabled.
2. If the configuration is not saved, it will be lost when the switch is
powered off.
QoS Configuration
„
Qos Policy: select the Qos policy rule
¾
Using the 8,4,2,1 weight fair queue scheme: The switch will
follow 8:4:2:1 rate to process priority queue from Highest to lowest.
For example: the system will process 8 high queue packets, 4
middle queue packets, 2 low queue packets, and one lowest
queue packets at the same time
¾
Use the strict priority scheme: The highest queue will always be
processed first.
„ Priority Type: Every port has 5 priority types
¾
Port-base: The port priority will follow the default port priority
assigned – High, middle, low, or lowest
Manual Documentation Number: EIR505-xx_5107m
41
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
¾
¾
¾
COS only: The port will follow the COS priority assigned
TOS only: The port will follow the TOS priority assigned
COS first: The port will follow COS priority first, and then another
priority rule
¾
TOS first: The port will follow TOS priority first, and then another
priority rule
„ COS priority: Set the COS priority level 0~7
„ TOS priority: The system provides 0 to 63 TOS priority levels. Each
level has 4 types of priority – high, mid, low, and lowest. The default
value is “Lowest”. When the IP packet is received, the system will check
the TOS value.
[NOTE] QoS and Rate control cannot be used simultaneously.
42
Manual Documentation Number: EIR505-xx_5107m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
QoS configuration Interface
IGMP
The Internet Group Management Protocol (IGMP) is an internal protocol of
the Internet Protocol (IP) suite. IP manages multicast traffic by using
switches, routers, and hosts that support IGMP. Enabling IGMP allows the
ports to detect IGMP queries and report packets and manage IP multicast
traffic through the switch. IGMP has three fundamental types of messages:
Manual Documentation Number: EIR505-xx_5107m
43
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Message
Query
Description
A message sent from an IGMP router or switch
requesting a response from each host belonging to
the multicast group.
A message sent by a host indicating that the host
wants to be or is a member of a given group.
Report
A message sent by a host indicating that the host
has is no longer a member of a specific multicast
group.
Leave Group
[NOTE] If the configuration is not saved, it will be lost when the switch
is powered off.
IGMP Snooping interface
44
Manual Documentation Number: EIR505-xx_5107m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Security Manager
Use to change the web management login user name and password.
1. User name: enter the new user name(The default is “root”)
2. Password: enter the new password(The default is “root”)
3. Confirm password: reenter the new password
Apply
4. Click
[NOTE] If the configuration is not saved, it will be lost when the switch
is powered off.
Security Manager Interface
Configuration Backup
Used to backup the configuration to a TFTP server and load the backup
configuration from the TFTP server.
TFTP Restore Configuration
Restore flash ROM value from the TFTP server.
1. TFTP Server IP Address: Enter the TFTP server IP
2. Restore File Name: Enter the file name
Apply
3. Click
Manual Documentation Number: EIR505-xx_5107m
45
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
TFTP Restore Configuration interface
TFTP Backup Configuration
Save current flash ROM value to the TFTP server
1. TFTP Server IP Address: Enter the TFTP server IP
2. Backup File Name: Enter the file name
Apply
3. Click
TFTP Backup Configuration interface
TFTP Update Firmware
Use to update firmware. Ensure the TFTP server is ready and the firmware
image is stored on the TFTP server,
1. TFTP Server IP Address: Enter the TFTP server IP Address
2. Firmware File Name: Enter the name of firmware image
Apply
3. Click
46
Manual Documentation Number: EIR505-xx_5107m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
TFTP Update Firmware interface
Factory Default
Reset the Switch to the default configuration. NOTE: The IP Address,
subnet mask, default gateway, username, and password will remain as
configured by the user.
Default
„
Click
Factory Default interface
System Reboot
Reboot the switch in software reset
Reboot
„
Click
System Reboot interface
Manual Documentation Number: EIR505-xx_5107m
47
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Save Configuration
Save the configuration to flash memory. If the switch is powered off without
saving the configuration, all changed configuration will lost
Save Flash
„
Click
Save Configuration Interface
Rate Control
Set up each port’s bandwidth rate and packet limitation type
„
Limit Packet type: Select the packet type to filter. The packet filter
types are all packet types, broadcast/multicast/unknown, unicast
packets, broadcast/multicast packets, and broadcast packet only. The
broadcast/multicast/unknown, unicast packet, broadcast/multicast
packet, and broadcast packet only are only for ingress. The egress rate
only supports all packet types.
„
Ports 1 through 5 support port ingress and egress rate control. For
example, assume port 1 is 10Mbps, users can set its effective egress
rate to 1Mbps, and the ingress rate to 500Kbps.
¾
Ingress: Select the port effective ingress rate. The valid range
value is 1MB, 2MB, 4MB, 8MB, 16MB, 32MB and 64MB. The
default value is “disable”
¾
Egress: Select the port effective ingress rate. The valid range
value is 128kbps, 256Kbps, 512Kbps, 1MB, 2MB, 4MB, and 8MB.
The default value is “disable”
Apply
„
Click
48
Manual Documentation Number: EIR505-xx_5107m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
[NOTE]
1. If the configuration is not saved, it will be lost when the switch is
powered off.
2. Qos and Rate control cannot exist at the same.
Rate Control Interface
Manual Documentation Number: EIR505-xx_5107m
49
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Trouble shooting
„
„
Verify the power supply is correct (12-48V DC) Do not exceed 48V DC.
Ensure the proper UTP cable is used for RJ-45 connections: 100Ω
Category 3, 4 or 5 cable for 10Mbps connections or 100Ω Category 5
cable for 100Mbps connections. Ensure that the length of any
twisted-pair connection does not exceed 328 feet (100 meters).
LED Indicators: Assist in identifying problems.
„
50
Manual Documentation Number: EIR505-xx_5107m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Specification
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast Ethernet
IEEE802.3x Flow Control and Back-pressure
IEEE802.1d spanning tree / IEEE802.1w rapid
spanning tree
Standards
IEEE802.1p class of service
IEEE802.1Q VLAN Tag
Protocol
CSMA/CD
Provides Web interface management and one
default button for system default setting
Management
Technology
Store and forward switching architecture
14,880 pps for Ethernet port
Transfer Rate
148,800 pps for Fast Ethernet port
Transfer packet
size
64bytes to 1522 bytes (with VLAN tag)
2K MAC address table
MAC address
Memory Buffer
Back-plane
1Mbits
1.0 Gbps
Packet throughput
ability
1.49Mpps @64bytes (4TX +1 FX)
Manual Documentation Number: EIR505-xx_5107m
51
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Per port: Link/Activity (Green), Full
duplex/Collision (Yellow)
Per unit: Power (Green), Power 1 (Green),
LED
Power 2 (Green), Fault (Yellow), Master (Green)
10Base-T: 2-pair UTP/STP Cat. 3, 4, 5 cable
EIA/TIA-568 100-ohm (100m)
Network Cable
100Base-TX: 2-pair UTP/STP Cat. 5 cable
EIA/TIA-568 100-ohm (100m)
SC (Multi-mode): 50/125um~62.5/125um
SC (Single mode): 9/125um~10/125um
Available distance: 2KM (Multi-mode) / 30KM
(single-mode)
Optical cable
Wavelength: 1310nm (multi-mode/ single mode)
Redundant 12 to 48 V DC power inputs with
reverse polarity protection
Power Supply
Power
3.64 Watts
consumption
4 selection rules :
„
„
All packets
Broadcast/ multicast/ unknown unicast
packets
Packet filter
„
„
Broadcast/ multicast packets
Broadcast packets only
IEEE802.1p class of service support, 4 priority
queues per port.
Class of service
52
Manual Documentation Number: EIR505-xx_5107m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
port based
Quality of service
Tag based
IPv4 Type of service
X-Ring
300 ms Recovery Time
Port based VLAN and IEEE802.1Q Tag VLAN.
Both port based and Tag based VLAN groups
(up to 64).
VLAN
IEEE802.1d spanning tree and IEEE802.1w
rapid spanning tree.
Spanning tree
IGMP
SNTP
IGMP v1 and Query mode. Up to 256 groups.
Simple Network time protocol
Management IP
security
IP address security to prevent intrusion
Port mirror
TX packet only or both TX and RX packet.
Manual Documentation Number: EIR505-xx_5107m
53
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Install
Alarm
DIN rail and panel mount
One 24VDC, 1A relay output.
TFTP firmware update
Firmware update
DHCP client
TFTP configuration backup and restore.
DHCP client function to obtain the IP address
from a DHCP server.
„
„
Ingress packets filter and egress packet limit
The egress rate control supports all of
packet type and the limit rates are 128kbps,
256Kbps, 512Kbps, 1MB, 2MB, 4MB, and
8MB
„
Ingress filter packet type combination rules
are Broadcast/Multicast/Unknown Unicast
packet, Broadcast/Multicast packet,
Broadcast packet only and all of packet. The
packet filter rate can be set follow
Bandwidth control
as:1Mbps、2Mbps、4Mbps、8Mbps、
16Mbps、32Mbps、64Mbps
0℃ to 60℃ (32℉ to 140℉)
5% to 95% (Non-condensing)
-40℃ to 85℃
Operation Temp.
Operation
Humidity
Storage
Temperature
IP-30, 2.12 (W) x 4.31 (H) x ,4.13 (D) in (5.4 x
13.5 x 10.5 cm)
Case Dimension
54
Manual Documentation Number: EIR505-xx_5107m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Class A, CE EN6100-4-2, CE
EN6100-4-3, CE EN-6100-4-4,
CE EN6100-4-5, CE EN6100-4-6
EMI
Safety
EN60950
IEC60068-2-32 (Free fall), IEC60068-2-27
(Shock), IEC60068-2-6 (Vibration)
Stability testing
Manual Documentation Number: EIR505-xx_5107m
55
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Download from Www.Somanuals.com. All Manuals Search And Download.
|