SELECTRONIC™
Thermostatic Mixing Valve
605XTMV
Specifications
1
2
3
3
4
Installation
Adjust Temperature
Service
Replacement Parts
Certified to comply with ASME A112.18.1M
© 2005 American Standard
M968808
NOTE TO INSTALLER: Please give this manual to the customer after installation.
customer's e-mail us at: [email protected]
For Parts, Service, Warranty or other Assistance,
please call 1-800-442-1902 (In Canada: 1-800-387-0369)
(In Toronto Area only: 1-905-3061093)
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 3
INSTALLATION
LAVATORY RIM OR
MOUNTING SURFACE
MOUNT ENCLOSURE; Fig. 3
1
1. Remove the bottom SUPPLY HOSE (1) from the
SELECTRONIC ENCLOSURE (2). Fig. 3
Fig. 3a
SUPPLIES
2
2. Remove BOTTOM PLUG (3) from SELECTRONIC
ENCLOSURE (2). Fig. 3
1
3
3. Remove 4 screws from MIXER ENCLOSURE
COVER (2) and pull off COVER (2). Fig. 3b
WASTE
4-1/4"
(108mm)
ENCLOSURE
MOUNTING
HOLES
4. Remove MIXING VALVE (7) from ENCLOSURE (3).
Fig. 3b
MOUNTING HOLES
5. Install MIXER ENCLOSURE (4) under SELECTRONIC
ENCLOSURE (2) as shown in Fig. (3a). Hold the MIXER
ENCLOSURE (4) in that location and mark the four
mounting hole locations as shown. Fig. (3a)
1-3/16"
(46mm)
NOTE: MIXER ENCLOSURE SUPPLY HOSES are
20" long. Distance between wall valves and MIXER
ENCLOSURE (4) must be taken into consideration.
6
4
4
2
7
5
5. The ENCLOSURE (4) works best if secured to a wall
stud or cross brace within the wall, using the SCREWS
(5) supplied. If the MIXER ENCLOSURE (4) is to be
installed on a tile or plaster wall the ANCHORS (6) and
SCREWS (5) should be used.
ILLUSTRATION SHOWN
LESS MIXING VALVE
6. For installations on drywall or tiled walls; use
ANCHORS (6) and SCREWS (5) for securing MIXER
ENCLOSURE (4) to finished wall. Drill four 1/4" dia.
holes a minimum of 1-3/4" deep. Insert the four
ANCHORS (6) flush with face of the finished wall.
Align the MIXER ENCLOSURE (4) and Install the
MOUNTING SCREWS (5). Tighten to secure MIXER
ENCLOSURE (4) to mounting surface.
ADJUSTABLE
WRENCH
Fig. 4
2
Fig. 4a
2
4
3
CONNECT MIXING VALVE; Fig. 4
2
1. Install MIXING VALVE (1) back into ENCLOSURE.
2. Install FIBER SEAL WASHER (4) on MIXING
VALVE NIPPLE (3). Hold MIXING VALVE (1) in place
with one hand and with your other hand thread
SWIVEL NUT (2) onto MIXING VALVE NIPPLE (3).
Fig. 4. Use an adjustable wrench to tighten SWIVEL
NUT (2). Fig. 4a
1
3. Replace ENCLOSURE COVER and tighten securely.
CONNECT MIXING VALVE TO
3
Fig. 5
WATER SUPPLIES; Fig. 5
1. Turn off hot and cold water supplies before
beginning.
2. Connect FLEXIBLE SUPPLIES (1, 2) directly to wall
supplies. Connection on MIXER supplies are 3/8"
compression. Connect left supply to Hot and right
supply to Cold wall supply. Use adjustable wrench to
tighten connections. Do not over tighten. FIG. 5
WALL SUPPLIES
HOT
COLD
2
3. Faucet supplies measure 20" from the bottom of the
ENCLOSURE (3) base.
1
3
Note: If additional supply length is required, installer
must purchase parts separately.
Important: If SUPPLY HOSES (1, 2) are too long, loop
as to avoid kinking.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 6
ADJUST TEMPERATURE
TO DECREASE
TEMPERATURE
TO ADJUST TEMPERATURE;
4
4mm HEX
WRENCH
Fig. 6
1. Adjust temperature by inserting a 4mm Hex Wrench
into hex opening in the side of enclosure. Fig. 6.
TO INCREASE
TEMPERATURE
2. To decrease temperature, rotate up. (clock-wise)
3. To increase temperature, rotate down. (counter-
clockwise)
Fig. 7
Fig. 7a
2
SERVICE
6, 4
TO SERVICE CARTRIDGE; Fig; 7
5
1. Turn off water supply.
1
5
3
2. Remove MIXING VALVE ENCLOSURE COVER.
1
3. Disconnect MIXING VALVE (1) from SELECTRONIC
ENCLOSURE (2). Fig. 7.
4. Pull MIXING VALVE (1) out from ENCLOSURE (5).
If SUPPLY HOSES (3) are not long enough to gain
access to TEMPERATURE CALIBRATION UNIT (6)
&THERMOSTATIC CARTRIDGE (4) disconnect
SUPPLY HOSES (3) from wall valves. Fig. 7a.
Fig. 7b
Fig. 7c
6
5. Rotate the BLACK CLAMP (7) with your finger and
pull off the TEMPERATURE CALIBRATION UNIT (6).
Fig 7b, 7c.
6. Use a adjustable wrench to unthread
THERMOSTATIC CARTRIDGE (4) from housing. Fig. 7d.
7
7. Remove THERMOSTATIC CARTRIDGE (4). Fig. 7e.
Fig. 7d
Fig. 7e
8. Rinse clean any debris from SCREENS (8) and
inspect O-RINGS (9) for damage. Replace O-RINGS (9)
if any damage is found. Fig. 7f.
4
9. Reverse above steps and reassemble MIXING
VALVE (1). Assemble MIXING VALVE (1) to
SELECTRONIC ENCLOSURE (2).
4
10. Assembly ENCLOSURE COVER and tighten
securley.
8
Fig. 7f
4
9
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SELECTRONIC™
THERMOSTATIC
MIXING VALVE
REPLACEMENT PARTS
PRODUCT NUMBER
605XTMV
A922255-0070A
ENCLOSURE
A922256-0070A
ENCLOSURE COVER
M962387-0070A
MOUNTING SCREW &
ANCHOR KIT
A954820-0070A
THERMOSTATIC
CARTRIDGE
A918549-0070A
ENCLOSURE SCREWS
953957-0070A
TEMPERATURE
CALIBRATION UNIT
A924163-0070A
SUPPLY HOSES
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Weekdays 8:00 a.m. to 8:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2005
M968808
4
Download from Www.Somanuals.com. All Manuals Search And Download.
M968808
Download from Www.Somanuals.com. All Manuals Search And Download.
|