37
37
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
FOR YOUR SAFETY ……………………………………………………....
PRCAUTIONS AND REMINDERS ……………………………………….
IMPORTANT SAFETY INSTRUCTIONS ………………………………..
Package Contents…………………………………………………
Attaching the Base …………………………………………………
Preparing Your LCD HDTV for Wall Mounting ………………
PREPARATION ……………………………………………………………
2
4
6
8
8
9
10
PERIPHERAL CONNECTION GUIDE …………………………………. 12
OPERATING INSTRUCTIONS …………………………………………. 14
TO USE THE FRONT PANEL CONTROL ……………………... 14
TO USE THE REMOTE CONTROL ………………………….…. 15
VIEWING MODES ILLUSTRATIONS ………………………….…. 16
CONNECTING EQUIPMENT ………………………….……….
18
TO USE THE MENUS ……………………………………………. 30
SETUP MENU …………………………………………………….. 30
VIDEO MENU ……………………………………………………... 31
AUDIO MENU ……………………………………………………... 32
FEATURE MENU …………………………………………………. 33
TIPS ………………………………………………………………… 37
PRODUCT SPECIFICATION ………………………………………...…. 39
BEFORE CALLING SERVICE ……………………………………..…… 40
GLOSSARY ……………………………………………………….. 41
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOL
SA 1965
SYMBOL DEFINITION
DANGEROUS VOLTAGE: The lightning flash with
arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that
may be of sufficient magnitude to constitute a risk of
electrical shock to persons.
INSTRUCTIONS: The exclamation point within on
equilateral triangle to alert the User to the presence of
important operating and maintenance (servicing)
instruction In the literature accompanying the appliance.
SA 1966
Apparatus shall not be exposed to dripping or splashing and no objects filled
with liquids, Such as vases, Shall be placed on the apparatus.
Caution - Danger of explosion if battery is incorrectly replaced. Replace only
with the same or equivalent type.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
FOR YOUR SAFETY
Before operating the TV please read this manual thoroughly. This manual should
be retained for future reference.
FCC Class B Radio Frequency Interference Statement
WARNING: (FOR FCC CERTIFIED MODELS)
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy, and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
NOTICE
1. The changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
2. Shielded interface cables and AC power cord, if any, must be used in order to
comply with the emission limits.
3. The manufacturer is not responsible for any radio or TV interference caused
by unauthorized modification to this equipment. It is the responsibilities of the
user to correct such interference.
WARNING:
To prevent fire or shock hazard, do not expose the TV to rain or moisture.
Dangerously high voltages are present inside the TV. Do not open the cabinet.
Refer servicing to qualified personnel only.
SAFETY: Lamp Disposal
LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED
OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS. FOR MORE
INFORMATION, CONTACT THE ELECTRONIC
INDUSTRIES ALLIANCE AT WWW.EIAE.ORG.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
DIGITAL TELEVISION TRANSITION NOTICE
This device contains a digital television tuner, so it should receive digital over the
air TV programming, with a suitable antenna, after the end of full-power analog
TV broadcasting in the United States on February 17, 2009. Some older television
receivers, if they rely on a TV antenna, will need a TV Converter to receive over
the air digital pro-gramming, but should continue to work as before for other
purposes (e.g., for watching low-power TV stations still broadcasting in analog,
watching pre-recorded movies, or playing video games).
For more information,
call the FCC at 1-888-CALL-FCC (1-888-225-5322)
government coupons that may be used toward the purchase
or call the NTIA at 1-888-DTV-2009.
AVISO RELATIVO A LA TRANSICIÓN A TELEVISIÓN DIGITAL
Este equipo incorpora un sintonizador de televisión digital, lo que le permitirá
recibir una programación digital televisada por aire, con una antena adecuada,
cuando se terminará la transmisión de alta potencia de la televisión analógica en
los Estados Unidos el 17 de febrero de 2009. Ciertos receptores de televisión
antiguos, si dependen de una antena de TV, necesitarán un conversor de TV
para recibir por el aire una programación digital, pero seguirán funcionando como
antes para otros usos (por ejemplo para ver emisoras de TV de baja potencia que
todavía transmiten en analógico, para ver películas pregrabadas, o para utilizar
sus videojuegos).
Para obtener más información,
llame FCC 1-888-CALL-FCC (1-888-225-5322)
conversores de TV, y acerca de los cupones del gobierno que se pueden usar
o llame al NTIA al 1-888-DTV-2009.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS AND REMINDERS
Place unit on even surfaces.
Don't place the TV in confined spaces
or in a box when using it.
Unplug immediately if is malfunction Unplug immediately if other foreign
like no picture, no video/audio,smoke materials are put inside TV box or if
and bad odor from TV.
the TV fell down.
Don't throw any object inside the TV
box like metals or other flammable Prohibit/Avoid opening TV cabinet
materials.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Remember to unplug the AC cord Avoid direct sunlight, dusty, high
from the AC outlet before cleaning. Do humidity and smoky areas.
not use liquid cleaners or aerosol
cleaners to clean the display.
Make sure to unplug the unit when not Call service personnel to clean the
in use for a long period of time (days). internal part of the TV once a year.
Do not cover or block any vents and Do not place the display near water,
openings. Inadequate ventilation may such as bathtub, washbasin, kitchen
shorten the life of the display unit and sink laundry tub, swimming pool or in
cause overheating.
a damp basement.
Notice for Remote Controller
Avoid Dropping
Avoid Liquids
Avoid Aerosol Cleaners
3
2
1
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
Read before operating equipment
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any of the ventilation openings. Install in accordance with the
manufacturers instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves,
or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding type plug. A
polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and third grounding prong. The wide blade or third
prong is provided for your safety. When the provided plug does not fit into
your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with a cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
13. The TV should be operated only from the type of power source indicated on
the label. If you are not sure of the type of power supplied to your home,
consult your dealer or local power company.
14. Unplug this apparatus during lightning storms or when unused for long
periods of time.
15. Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects have fallen into apparatus,
the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
16. This product may contain lead or mercury. Disposal of these materials may
be regulated due to environmental considerations. For disposal or recycling
information, please contact your local authorities or the Electronic Industries
17. Damage Requiring Service – The appliance should be serviced by qualified
service personnel when:
A. The power supply cord or the plug has been damaged; or
B. Objects have fallen, or liquid has been spilled into the appliance; or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or exhibits a marked
change in performance; or
E. The appliance has been dropped, or the enclosure damaged.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
18. Tilt/Stability – All televisions must comply with recommended international
global safety standards for tilt and stability properties of its cabinets design.
y
Do not compromise these design standards by applying excessive pull
force to the front, or top, of the cabinet, which could ultimately overturn
the product.
y
Also, do not endanger yourself, or children, by placing electronic
equipment/toys on the top of the cabinet. Such items could
unsuspectingly fall from the top of the set and cause product damage
and/or personal injury.
19. Wall or Ceiling Mounting – The appliance should be mounted to a wall or
ceiling only as recommended by the manufacturer.
20. Power Lines – An outdoor antenna should be located away from power lines.
21. Outdoor Antenna Grounding – If an outside antenna is connected to the
receiver, be sure the antenna system is grounded so as to provide some
protection against voltage surges and built up static charges.
Section 810 of the National Electric Code, ANSI/NFPA No. 70-1984, provides
information with respect to proper grounding of the mats and supporting
structure grounding of the lead-in wire to an antenna-discharge unit, size of
grounding connectors, location of antenna-discharge unit, connection to
grounding electrodes and requirements for the grounding electrode. See
Figure below.
EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL
CODE
Note to the CATV system installer: This reminder is provided to call the
CATV system installer’s attention to Article 820-40 of the NEC that provides
guidelines for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the building, as close
to the point of cable entry as practical.
Please, make sure to connect the power plug to the wall outlet socket after
connecting the TV to the adapter!
22. Objects and Liquid Entry – Care should be taken so that objects do not fall
and liquids are not spilled into the enclosure through openings.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Package Contents
◎AOC L37W861 TV unit
◎Remote Control
◎Two (AAA) Batteries for the Remote Control
◎Base
◎Four screws (to attach the Base to the stand)
◎Power Cord
◎User Manual
◎Quick Setup Guide
IMPORTANT: Do not apply pressure to the screen display area which may
compromise the integrity of the display. The manufacturer’s warranty does not
cover user abuse or improper installations.
Attaching the Base
IMPORTANT: The Base of the HDTV must be assembled prior to usage.
1. Place TV unit face down on a soft
and flat surface (blanket, foam,
cloth, etc.) to prevent any
damage to the HDTV.
2. Carefully align and insert the
Base to the stand.
3. Gently push the Base towards
the HDTV until the locking
mechanism locks into place.
4. Insert the provided screws to the bottom of the base.
5. Use a screwdriver to tighten the Base to the stand.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparing Your LCD HDTV for Wall Mounting
We suggest that you keep your TV at least
2.36 inches (60 mm) from the wall to prevent
cable interference.
Before mounting your TV on the wall, you need to remove the base.
To attach a wall mount bracket to your TV:
1
2
Remove the two T4 and two M4 screws holding your TV to the stand.
Secure the wall mount bracket to the back of your TV using four M6 screws,
as indicated in the illustration.
Note: 200mmx200mm wall mount bracket & M6 screws not included.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
Please, make sure to connect the power plug to the wall outlet socket after
connecting the TV to the power cord!
1. Install the base stand; place the TV on a solid surface.
Ensure that the TV is placed in a position to allow free flow of air. Do not cover
the ventilation openings on the back cover.
To prevent any unsafe situations, no naked flame sources, such as lighted
candles, should be placed on or in the vicinity.
Avoid heat, direct sunlight and exposure to rain or water. The equipment shall
not be exposed to dripping or splashing.
2. Connect the antenna cable or CATV cable to the aerial socket ANT IN 75Ω at
the back of the TV set.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Remote control:
Remove the cover of the battery compartment. Insert the 2 batteries supplied
(Type AAA 1.5V).
4. Power:
Insert the power cord in the wall socket having an AC power supply. You can
see LED states at the front panel. If the LED color is Blue, means the TV set is
power on. If the LED color is Red, which means this TV set is in standby state.
5. Turn the TV on:
Push the POWER key on the Remote control or the Front panel control knobs.
Wait a minute, the TV will power on and can see the display on the screen
POWER Key
11
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIPHERAL CONNECTION GUIDE
HDMI
S-Video Composite
Pr
Pb
Y
PC Audio in 15-pin D-Sub
1.
HDMI – Connect the primary source for digital video such as a DVD
multimedia player or set top box through this all digital connector.
The white color band on the rear of the TV indicates this connection.
2.
3.
RGB PC – Connect the video and audio cables from a computer
here.
AV/S-VIDEO IN – Connect the primary source for composite video
devices, such as a VCR or video game. Use the white and red
connectors to connect the external audio from the same source.
The signal being carried by the S-Video cable and connector, if
connected, will take priority over the Video RCA connector (yellow
connector).
12
Download from Www.Somanuals.com. All Manuals Search And Download.
4.
COMPONENT (YPb/CbPr/Cr with Audio L/R) – Connect the
primary source for component video devices such as a DVD Player
or set top box here. From left to right, use red for Pr, blue for Pb,
green for Y, red for right audio (R) and white for left audio (L) inputs.
5.
6.
DTV – Connect to an antenna or digital cable (out-of-the-wall, not
from Cable Box) for Digital TV.*
SPDIF (Optical Digital Audio Out) - When a digital audio signal is
associated with the input selected for viewing, the digital audio will
be available on this SPDIF connection to your home theater system.
Once your equipment is connected, use the following procedure to view the input
signal:
Press the source button on the remote controller to select the relevant source to
view. (ex: Press VIDEO button to select “Composite Rear” if you have connected
a video recorder to Composite Rear socket.)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUCTIONS
TO USE THE FRONT PANEL CONTROL
1.
VOL +
VOL -
VOL +: Press to increase the sound volume level.
2.
3.
4.
5.
6.
VOL - : Press to decrease the sound volume level.
CH +: Press to select the next higher Program number.
CH - : Press to select the next lower Program number.
Menu key: Press to open or exit the OSD menu.
Source key: Press to select the input source.
CH ▲
CH ▼
MENU
INPUT
Power key: Press to turn on / off (standby) the TV set.
(Please re-turn on TV after the Power-ON status LED had
changed to the Red color and finished flashing.)
7.
POWER
14
Download from Www.Somanuals.com. All Manuals Search And Download.
TO USE THE REMOTE CONTROL
POWER
PREV CH
Press to display the previous TV .
Press to power ON/OFF (standby)
TV.(Note:1.TV is never completely
power off.
unless physically unplugged.
2.Press to turn on TV after the
power
on status LED had changed to the
red color and stopped flashing. )
MTS/SAP
Press to activate the NTSC TV
sounds, such as: Stereo, SAP or
Mono tone. And languages of DTV.
WIDE
VIDEO
Press to choose the display aspect
as: Normal, Wide, Zoom or Cinema
mode.
Press repeatedly to choose S-
Video/Composite source mode
(Video 1 ~ 2).
SOURCE
Press repeatedly to choose the
various input sources (Video 1 ~ 6).
COMP
Press repeatedly to choose
Component source mode (Video 3 ).
EPG
This function is not support.
PC/HDMI
MUTE
Press repeatedly to choose VGA
or HDMI source mode (Video 4 ~
6).
Press to set TVsound mute ON/OFF
DISPLAY
Press to show the information about
the input source、TV channel、
display resolution and current time.
TV
Press to choose ATSC/NTSC TV
source mode.
VOL- / VOL+
0 ~ 9 /- number
Press + or - to adjust the volume.
Press to enter TV channel number
to select channel (Press ‘-’ to
indicate choosing the sub-channel).
Exit
Press to exit menu or OSD.
SLEEP
V-CHIP
Press to set a time period (off/5
min /10 min /15 min /30min/45
min /60min/90min/120 min /180
min /240 min)after which the TV
shouldswitch itself to standby
mode.
Press to lock / unlock Parental
Control temporarily. (After setting
the restricted table of MPAA or TV
Rating.)
VIDEO ADJ
Press to choose the Brightness or
Contrast adjustment.
FREEZE
Press to freeze the displayed
picture
AUDIO ADJ
Press to switch the ATSC multi-
channel TV sounds.
CH-/ CH +
Press + or - to browse through the
TV channels.
CC
Press repeatedly to change the
closed caption type as CC ON/CC
OFF/CC ON WHEN MUTE.
MENU
Press to open or exit menu.
“∧”,“∨”,“＜”,“＞”,“ENTER
FAVORITE
Press to toggle the Favorite/Normal
mode.
Press to adjust the various
function items on the menu.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
VIEWING MODES ILLUSTRATIONS
Normal Mode on 16:9 Display screen
The original content would be at the center of the
screen.
Wide Mode on 16:9 Display screen
The original content in this mode has to fill the entire
width of the display horizontally.
Wide Mode on 16:10 Display screen
Wide1 and Wide2 are applied:
Wide1: The original content would fill the full
screen while the proper ratio of 16:9 content
is still maintained. Little cropping of the content
on the sides is necessary.
Wide2: The original content would fill the width of the
screen while the proper ratio of 16:9 content is still
maintained. Small black bars are added.
ZOOM Mode on 16:9 Display screen
For those wide format images which are originally programmed into 4:3 frames
with top and bottom black bars, this mode has to stretch the image in both wide
and high directions to the full display with active data.
16:9 image in 4:3 frame
Same image in ZOOM mode
16
Download from Www.Somanuals.com. All Manuals Search And Download.
ZOOM Mode on 16:10 Display screen
For those wide format images which are originally programmed into 4:3 frames
with top and bottom black bars, this mode has to stretch the image in both wide
and high directions to the full display with active data. Little cropping on sides is
necessary for full display.
16:9 image in 4:3 frame
Same image in ZOOM mode
CINEMA Mode on 16:9 or 16:10 Display screen
This mode is applied to view 2.35:1 format content on 16:9 displays. To crop both
right and left sides a little for keeping the undistorted ratio of the image is provide
for users.
Note: AOC L37W861 has 4 picture formats: Normal, Wide, Zoom and
Cinema.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING EQUIPMENT
Coaxial (RF)
Using Your Antenna or Digital Cable for DTV
1. Turn off the power to the HDTV.
2. Connect the coaxial (RF) connector from your antenna or digital cable
(out-of-the-wall, not from the Cable Box) to the ANTENNA/CABLE
DIGITAL/ANALOG connector.
3. Turn on the power to the HDTV.
4. Select DTV using the INPUT button on the remote, side of the HDTV or
directly by pressing the TV button on the Remote Control.
Using Your Antenna or Cable for TV
1. Turn off the power to the HDTV.
2. Connect the coaxial (RF) connector from your antenna or cable (out-of-
the-wall, not from the Cable Box) to the ANTENNA/CABLE
DIGITAL/ANALOG connector at the rear of the HDTV
3. Turn on the power to the HDTV.
4. Select TV using the INPUT button on the remote, side of the HDTV or
directly by pressing the TV button on the Remote Control.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Antenna or Cable for your VCR
1. Turn off the power to the HDTV and VCR.
2. Connect the “Output to TV”, “RF Out” or “Antenna Out” connector on the
rear of your VCR to the ANTENNA/CABLE DIGITAL/ANALOG connector
at the rear of the HDTV.
3. Turn on the power to the HDTV and VCR.
4. Select TV using the INPUT button on the remote, side of the HDTV or
directly by pressing the TV button on the Remote Control.
Note: If you have an off-air antenna or cable TV, connect it to the
“Antenna In” connector on the rear of your VCR.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your HDTV Set-Top Box
Using HDMI
HDTV Set-Top Boxes that have a HDMI digital interface should be connected
to the HDMI input of the LCD HDTV for optimal results.
Connecting your HDTV Set-Top Box (Best)
1. Turn off the power to the HDTV and HDTV Set-Top Box.
2. Connect a HDMI cable to the HDMI output of your HDTV Set-Top Box and
the other end to the HDMI Input at the rear of the HDTV.
3. Turn on the power to the HDTV and HDTV Set-Top Box.
4. Select HDMI using the INPUT button on the remote, side of the HDTV, or
directly by pressing the HDMI button on the Remote Control.
Note:
a) The HDMI input on the HDTV supports High-bandwidth Digital
Content Protection (HDCP). HDCP encrypts the transmission
between the video source and the digital display for added security
and protection.
b) Refer to your HDTV Set-Top Box user manual for more information
about the video output requirements of the product or consult your
20
Download from Www.Somanuals.com. All Manuals Search And Download.
For HDTV Set-Top Boxes with DVI
1. Turn off the power to the HDTV and HDTV Set-Top Box.
2. Using a HDMI-DVI cable, connect the DVI end to your HDTV Set-Top Box
and the HDMI end to the HDMI Input at the rear of the HDTV.
3. Turn on the power to the HDTV and HDTV Set-Top Box.
4. Select HDMI using the INPUT button on the remote, side of the HDTV, or
directly by pressing the HDMI button on the Remote Control.
Note:
a) The HDMI input on the HDTV supports High-bandwidth Digital Content
Protection (HDCP). HDCP encrypts the transmission between the video
source and the digital display for added security and protection.
b) Refer to your HDTV Set-Top Box user manual for more information about
the video output requirements of the product or consult your cable or
satellite operator.
c) The DVI to HDMI connection provides video only. Connection to an
alternate audio player is required for audio.
Using Component Video
Connecting your HDTV Set-Top Box (Better):
1. Turn off the power to the HDTV and HDTV Set-Top Box.
2. Connect the Pr (red color) connector on your HDTV Set-Top Box to the
corresponding Pr (red color) connector in the Component group.
3. Connect the Pb (blue color) connector on your HDTV Set-Top Box to the
corresponding Pb (blue color) connector in the Component group.
4. Connect the Y (green color) connector on your HDTV Set-Top Box to the
corresponding Y (green color) connector in the Component group.
5. Using an audio cable (red and white connectors), connect the cable to the
audio output connectors associated with the Component output on your
HDTV Set-Top Box and connect the other end to the audio connectors
associated with the Component.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Turn on the power to the HDTV and HDTV Set-Top Box.
7. Select Component (Video 3) using the INPUT button on the remote, side
of the HDTV or directly by pressing the Component button on the Remote
Control.
Note:
Refer to your HDTV Set-Top Box user manual for more information
about the video output requirements of the product or consult your
cable or satellite operator.
Connecting Your Basic Set-Top Box
Using Composite Video
1. Turn off the power to the HDTV and Set-Top Box.
2. Using an AV Cable, connect the Video (yellow color) connector on your
Set-Top Box to the corresponding Video (yellow color) connector in the AV
group at the rear of the HDTV.
3. Using the red and white connectors, connect the cable to the audio output
connectors associated with the Video output on your Set-Top Box and
connect the other end to the audio connectors associated with the AV
input at the rear of the HDTV.
4. Turn on the power to the HDTV and Set-Top Box.
5. Select Composite (Video 1) using the INPUT button on the remote, side of
the HDTV or directly by pressing the AV button on the Remote Control.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Coax (RF)
1. Turn off the power to the HDTV and Set-Top Box.
2. Using a Coax (RF) cable, connect one end to the TV OUT (RF) on your
Set Top Box and the other end to the DTV/TV input at the rear of the
HDTV.
3. Turn on the power to the HDTV and Set-Top Box.
4. Select TV using the INPUT button on the remote, side of the HDTV or
directly by pressing the TV button (below the WIDE button) on the Remote
Control.
Note: Refer to your Set Top Box user manual for more information about
selecting the video or RF output of the product.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your DVD Player
Using HDMI
DVD players that have a digital interface such as HDMI (High Definition
Multimedia Interface) should be connected to the HDMI input of the LCD
HDTV for optimal results.
Connecting your DVD Player (Best)
1. Turn off the power to the HDTV and DVD player.
2. Connect a HDMI cable to the HDMI output of your DVD player and the
other end to the HDMI Input at the rear of the HDTV.
3. Turn on the power to the HDTV and DVD player.
4. Select HDMI using the INPUT button on the remote, side of the HDTV or
directly by pressing the HDMI button on the Remote Control.
For DVD Players with DVI:
1. Turn off the HDTV and DVD player.
2. Using a HDMI-DVI cable, connect the DVI end to your DVD player and the
HDMI end to the HDMI Input at the rear of the HDTV.
3. Turn on the power to the HDTV and your DVD player.
4. Select HDMI using the INPUT button on the remote or side of the HDTV,
or directly by pressing the HDMI button on the Remote.
Note:
1. Refer to your DVD player user manual for more information about the
video output requirements of the product.
2. The DVI to HDMI connection provides video only. Connection to an
alternate audio player is required for audio output.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Component Video
Connecting your DVD Player (Better)
1. Turn off the power to the HDTV and DVD player.
2. Connect the Pr (red color) connector on your DVD player to the
corresponding Pr (red color) connector in the Component at the rear of the
HDTV.
3. Connect the Pb (blue color) connector on your DVD player to the
corresponding Pb (blue color) connector in the Component group at the
rear of the HDTV.
4. Connect the Y (green color) connector on your DVD player to the
corresponding Y (green color) connector in the Component group at the
rear of the HDTV.
5. Using an audio cable (red and white connectors), connect the cable to the
audio output connectors associated with the Component output on your
DVD player and connect the other end to the audio connectors associated
with the Component input at the rear of the HDTV.
6. Turn on the power to the HDTV and DVD player.
7. Select Component using the INPUT button on the remote, side of the
HDTV or directly by pressing the Component button on the Remote
Control.
Note: Refer to your DVD player user manual for more information
about the video output requirements of the product.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Using S-Video (AV)
Connecting your DVD Player (Good):
1. Turn off the power to the HDTV and DVD player.
2. Connect the S-Video jack on the rear of your DVD player to the S-Video
jack in the AV group on the rear of the HDTV.
3. Connect an audio cable (white and red connectors) to the audio output
connectors associated with the S-Video output on your DVD player and
connect the other end to the audio connectors associated with the AV
input on the rear of the HDTV.
4. Turn on the power to the HDTV and DVD player.
5. Select S-Video (Video 2) using the INPUT button on the remote, side of
the HDTV, or directly by pressing the AV button on the Remote Control.
Using Composite (AV) Video
Connecting your DVD Player (Good)
1. Turn off the power to the HDTV and DVD player.
2. Connect the Video (yellow color) connector on your DVD player to the
Video (yellow color) connector in the AV group.
3. Connect the R (red color) and L (white color) audio connectors on your
DVD player to the corresponding R (red color) and L (white color) audio
input connectors in the AV group.
4. Turn on the power to the HDTV and DVD Player.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Select Composite (Video 1) using the INPUT button on the remote, side of
the HDTV or directly by pressing the AV button on the Remote Control.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your VCR or Video Camera
1. Turn off the HDTV and VCR or Video Camera.
2. Connect the S-Video jack on the rear of your VCR or Video Camera to the
S-Video jack in the AV group on the rear of the HDTV.
3. Connect an audio cable (white and red connectors) cable to the audio
output connectors associated with the S-Video output on your VCR or
Video Camera and connect the other end to the audio connectors
associated with the AV input on the rear of the HDTV.
4. Turn on the power to the HDTV and VCR or Video Camera.
5. Select S-Video (Video 2) using the INPUT button on the remote, side of
the HDTV or directly by pressing the AV button on the Remote Control.
Note: Refer to your VCR or Video Camera user manual for more
information about the video output requirements of the product.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a PC Computer
1. Turn off the power to the HDTV and PC Computer.
2. Connect a 15-pin D-Sub RGB (VGA) cable to the RGB output of your pc
computer and the other end to the RGB PC input at the rear of the HDTV.
3. Connect the Audio Out on your pc computer to the RGB PC Audio input at
the rear of the HDTV.
4. Turn on the HDTV and PC Computer.
5. Select RGB using the INPUT button on the remote, side of the HDTV or
directly by pressing the RGB button on the Remote.
Note: For the best picture quality when connecting a PC computer through
RGB PC, set your PC computer timing mode to native resolution of panel.
Please refer to the PC or graphic card’s user guide for additional
information on how to set the timing mode and the video output
requirements of the product.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
TO USE THE MENUS
1. Press the MENU button to display the main menu
2. Use the cursor up/down to select a menu item.
3. Use the cursor left/right to enter a submenu.
4. Press the ENTER button to enable/disable the function.
5. Press the MENU or EXIT button to exit the menu.
Press the MENU button to enter the main OSD (On Screen Display). Adjust the
items including Setup menu, Video menu, Audio menu and Feature menu.
However, some function items in the menus may only be enabled in the particular
source modes.
SETUP MENU
The Setup menu in TV mode shows as below. In others source modes, the Setup
menu only shows Menu Language and Aspect Ratio items.
1. Tuning Band: Select TV source signal from the Air (antenna) or Cable (CATV).
2. DTV Signal: Show the intensity of the received DTV signal.
3. Auto Ch Search: Automatically scan all NTSC / ATSC TV channels and
then store in the channel table. In channel scan process, the OSD can
display the number of channels which had been found.
4. Add on Ch search:Add channels which are new found.
5. Manual Channel Set: Show the channel setup table. User can choose to
display the ATSC or NTSC TV channels and then edit (add/delete) the channel
numbers.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Channel Labels: Show the NTSC / ATSC TV channel label menu for user
modifying channel labels specifically.
7. Menu Language: Select the menu display language. (English / Espanol /
Francais)
8. Aspect Ratio: Select the display aspect ratio. (Normal/Zoom/Wide/Cinema)
9. Favorite Channel Mode: When favorite channel mode on user can edit
favorite channel table in favorite channel set option.
VIDEO MENU
The Video menu in most source modes shows as below. It provides several video
adjustment items for user fine tuning the video display. Only in VGA source
modes, the Video menu simply provides Contrast, Brightness, Back light and
Settings (Preset) items.
1. Contrast: Video contrast adjustment, the tuning range is 0 ~ 100.
2. Brightness: Video brightness adjustment, the tuning range is 0 ~ 100.
3. Sharpness: Video sharpness adjustment, the tuning range is -50 ~ 50.
4. Color: Video color chroma adjustment, the tuning range is 0 ~ 100.
5. Tint: Video tint adjustment, the tuning range is R50 ~ G50.
6. BackLight: Backlight strength adjustment, the tuning range is 0 ~ 10.
7. Settings: Restore the default video settings.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
AUDIO MENU
The Audio menu in TV mode shows as below. It provides audio adjustment for
user to modify the audio setting. Audio language setting is only available with
ATSC TV source, the option is disable under other source modes.
1.Audio Language:Change the audio language setting on ATSC TV programs
The number of the supported audio languages depends on the ATSC TV
programs.
2. Bass: Bass tone adjustment, the tuning range is 0 ~ 63. (The default state is
enabled)
3. Treble: Treble tone adjustment, the tuning range is 0 ~ 63. (The default state is
enabled)
4. Balance: Audio balance adjustment, the tuning range is L31 ~ R31.)
5. Surround sound: press this item to on/off the stereo sound effect for audio.
6. Digital Audio Output: Digital audio output format selection, user can choose
RAW (default) or PCM format or off.
7. TV Speaker: Choose to turn on / off the TV internal speaker. The digital audio
output signals、earphone output signals will not be turn-off even though the
TV speaker is off. The default setting is On.
8. Settings: Restore the default audio settings.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURE MENU
The Feature menu in TV mode shows as below. It provides certain optional
control functions such as time set, sleep timer, advanced video menu, Password
Set, parental control (V-chip) and Digtal closed caption setting. This menu gives
users the most flexibilities to satisfy their generally demands. According to the
various requirements in different source modes, certain features should be hidden
(disable) on the menu. The details footnotes will be described clearly below.
1. Time Set: Set current time. This sub-menu includesTime Set Mode ,Time
Zone and Time items. 【Time Set Mode】user can choose Auto or Manual,
【Time Zone】item provides user to set current time zone, such as: Pacific、
Alaska、Hawaii、Eastern、Central and Mountain.
【Time】item provides user
to set the time clock.
2. Sleep Timer: Enable or disable the TV standby timer. User can set the TV
standby timer as off / 5 min / 10 min / 15 min/ 30 min / 45 min / 60 min/ 90 min
/ 120 min / 180min/ 240min. Timer starts to count down after cursor leaving the
sub-menu. (At the moment, the item shows 『** min Left』and the cursor
highlights on the Feature icon.)
3. Advanced Video Menu: Provide the Noise Reduction、Color Temperature
and 3D Y/C. Dynamic Contrast options for enhancing video quality.
【
Noise Reduction
Off. The default setting is Mid.
Colour Temp gives three color temperature modes as: Normal、Warm and
Cool.
3D Y/C
】gives four NR effect degrees, such as: Low、Mid、High and
【
】
【
】
provides On / Off switches. The default setting is On.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
【
【
Dynamic Contrast
】user can choose 0n or Off.
Setting restores the default advanced video option settings.
】
4. Password Set: Change the 4-numeral parental control password. Three steps
are required for changing the password: Enter Old Password -> Enter New
Password -> Confirm New Password. Note: This item is only available in TV,
Composite and S-Video source modes. The default password is 『0 0 0 0』.
5. Parental Control: provide the parental Control (V-chip) function setting. Before
entering the Parental Control sub-menu, user has to key in the password first.
Then enter the Parental Lock item, User can modify the restricted table about
MPAA or TV Rating respectively. While exiting the sub-menu, the parental
control function is working. The inhibitive channels or source signals can be
un-lock through pressing the V-CHIP key on the remote control and then key in
the correct password. Note: This feature is only available in TV, Composite
and S-Video source modes. (The default password is: 0 0 0 0.)
34
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Digital Captions: Select the close caption options ( Service 1-6, Text
1-4 and CC 1-4) in digital TV mode. When select service 1 to service 6
you canmodulate parameters in the Digital Close Caption.
7. Digital Close Caption: Provide numerous options for setting the digital close
caption style. In the sub-menu.
【Style】item can be set as Automatic or Custom mode. If Custom mode is
selected, user can modify the detail styles described below. The setting result
will be shown immediately on the bottom side of the sub-menu OSD. Note:
This feature is only available in Digital TV(ATSC) mode.
【Size】: Digital close caption font size, which can be set as Small、Normal
or Large.
【Font】: Digital close caption font style, which can be chosen as Default or
Font 1 ~ 7.
【Text Color】: Giving Red / Green / Blue/ Yellow / Magenta / Cyan / Black /
White Colors.
【Text Opacity】: Giving Transparent / Translucent / Solid / Flashing modes.
【Background Color】: Giving Red / Green / Blue / Yellow / Magenta / Cyan /
Black / White Colors.
【Background Opacity】: Giving Transparent / Translucent / Solid / Flashing
modes.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
【 Edge Effect 】 : The text edge effects, which gives None / Raised /
Depressed / Uniform / Left Shadow / Right Shadow
modes.
【Edge Color】: The colors of text edge effects, which provides Red / Green /
Blue / Yellow / Magenta / Cyan / Black / White Colors.
8. Audio only: press this item for those TV programs with audio only and without
the display. When the audio only is on, you could still modify the volume.
9. Component Set: This option only shows and is available in component mode,
which provides fine tuning component display, such as: 【H-Position】、【V-
Position】, 【Clock】,【Phase】 and【Auto Adjust】.All these items are
giving the tuning range from 0 to 100.【Setting】item providesthe default
componentsetting values restoring.
10. VGA Set: This option only shows and is available in VGA mode, which
provides several items for the VGA display fine tuning, such as : 【 H-
Position】、【V-Position】、【Clock】and 【Phase】. All these items giving
the tuning range from 0 to 100.【Setting】item provides the default VGA
setting values restoring.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
TIPS
Care of the screen
Do not rub or strike the screen with anything hard as this may scratch, mar, or
damage the screen permanently.
Unplug the power cord before cleaning the screen. Dust the TV by wiping the
screen and the cabinet with a soft, clean cloth. If the screen requires additional
cleaning, use a clean, damp cloth. Do not use liquid cleaners or aerosol cleaners.
Mobile telephone warning
To avoid disturbances in picture and sound, malfunctioning of your TV or even
damage to the TV, keep away your mobile telephone from the TV.
End of life directives
We are paying a lot of attention to produce environmentally friendly in green focal
areas. Your new receiver contains materials, which can be recycled and reused.
At the end of its life specialized companies can dismantle the discarded receiver
to concentrate the reusable materials and to minimize the amount of materials to
be disposed of.
Please ensure you dispose of your old receiver according to local regulations.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory Notices – Federal Communications Commission Notice
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
y
Reorient or relocate the receiving antenna.
y Increase the separation between the equipment and the TV.
y Connect the equipment into wall power outlet on a circuit different from that
to which the receiver is connected.
y Consult the dealer or an experienced radio or television technician for help.
Modifications –
The FCC requires the user to be notified that any changes or modifications made
to this device that are not expressly approved by our company. may void the
user’s authority to operate the equipment.
Cables –
Connections to this device must be made with shielded cables with metallic
RF/EMI connector hoods to maintain compliance with FCC Rules and Regulations.
Canadian notice –
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Avis Canadian –
Cat apparel numerous de la classed B respected toutes les exigencies du
règlement sur le materiel brouilleur du Canada.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT SPECIFICATION
NOTE:
*This model complies with the specifications listed below.
*Designs and specifications are subject to change without notice.
*This model may not be compatible with features and/or specifications that may
be added in the future.
*37” LCD TV (37.0” viewable) Viewable image size: diagonal 940 mm
Television System:
HDMI Terminals:
NTSC standard
ATSC standard (8-VSB, Clear-QAM)
HDMI INPUT: Rear HDMI x2, Side HDMI x1
HDCP compliant
E-EDID compliant
Supported scan rates: 1080i, 720p, 480p, 480i
Channel Coverage:
VHF: 2 through 13
VGA Terminals:
VGA INPUT:
UHF: 14 through 69
CableTV:Mildband(A-8throughA-1,Athrough
I)
Super band (J through W)
Hyper band (AA through ZZ, AAA, BBB)
Ultra band (65 through 94, 100 through 125)
Rear VGA (D-SUB 15 Pin) Input x1
E-EDID compliant
Supported scan rates: 640X480 /60Hz
800x600 /60Hz
1024X768 /60Hz
1360X768 /60Hz
Recommended: 1360X768 /60Hz
Audio INPUT: Headphone Mini-jack for stereo (3.5Φ)
Power Source:
AC power supply: 100V~240 V, 50/60 Hz
Audio Output:
AUDIO: 500 mV(rms)
Power Consumption
≤ 200 W
Dimensions:
Include Stand:
1 W in standby mode (power cord plugged in
and power OFF)
904mm(W) x 636mm(H) x 230mm(L)
Audio Power
10 W + 10 W, Internal Speaker
Weight: 16kg(With Stand)
Video/Audio Terminals:
Rear AV x1: Side AV x 1
S-Video/Video/Audio Input
Wall Mounting:
200x200mm
(Wall mount kit is not included)
S-VIDEO INPUT:
Supplied Accessories:
1pcs Power cord
1pcs Remote control
(with two size AAA alkaline batteries)
1pcs User manual
Rear S-Video x 1, Side S-Video x 1
Y : 1 V(p-p), 75 ohm, negative sync.
C : 0.286 V(p-p) (burst signal), 75
ohm
1pcs Setup Guide
VIDEO/AUDIO INPUT:
VIDEO: 1 V(p-p), 75 ohm, negative sync.
AUDIO: 500 mV(rms)
Component INPUT:
Rear Component x 2
Y : 1V(p-p), 75 ohm, including sync.
Pr/Cr: ±0.35V(p-p), 75 ohm
Pb/Cb: ±0.35V(p-p), 75 ohm
AUDIO: 500 mV(rms)
Supported resolutions:1080i, 720p, 480p,
480i
39
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE CALLING SERVICE
Please make these simple checks before calling service. These tips may save
you time and money since charges for receiver installation and adjustments of
customer controls are not covered under your warranty.
Symptoms
Items to Check and Actions to follow
“Ghost ” or double image
*This may be caused by obstruction to the
antenna due to high rise buildings or
hills. Using a highly directional antenna
may inprove the picture.
No power
No picture
*Check that the TV’s AC power cord is plugged
into the mains socket.
*Unplug the TV, wait for 60 seconds. Then re-
insert plug into the mains socket and turn on
the TV again.
*Check antenna connections at the rear of the
TV to see if it is properly connected to the TV.
*Possible broadcast station trouble. Try
another channel.
*Adjust the contrast and brightness settings.
*Check the Closed Captions control. Some
TEXT modes could block the screen,
*Increase the VOLUME.
Good picture but no sound
*Check that the TV is not muted; press the
MUTE button on the remote control.
*Adjust the contrast, color and brightness
settings.
*Sometimes, poor picture quality occurs when
having activated an S-VHS camera or
camcorder connected and having connected
another peripheral at the same time. In this
case switch off one of the other peripherals
*Check the antenna connection
Good sound but poor color
Poor picture
Snowy picture and noise
Horizontal dotted line
*This may be caused by electrical interference
(e.g. hairdryer, nearby neon lights, etc.)
*Turn off the equipment.
Television not responding to
remote control
*Check whether the batteries are working.
Replace if necessary
*Clean the remote control sensor lens on the
TV.
*You can still use the buttons at the front of
your TV.
*Select the TV mode to be sure your remote
control is in the TV mode.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
GLOSSARY
HDTV
HDTV displays are technically defined as being capable of displaying a minimum
of 720p or 1080i active scan lines.
HDMI Inputs
High-Definition Multimedia Interface
Audio / Video Inputs
Located on the rear of the receiver, these connectors (RCA phono type plug) are
used for the input of audio and video signals. Designed for use with VCRs (or
other accessories) in order to receive higher picture resolution and offer sound
connection options.
Menu
An on-screen listing of features shown on the TV screen is made available for
user adjustments.
MPAA
Motion Picture Association of America
Multichannel Television sound (MTS)
The broadcasting standard, which allows stereo sounds to be transmitted with the
TV picture.
RF
Radio Frequency or modulated signal design used as the carrier for television
broadcasts.
Second Audio Program (SAP)
Another or additional audio channel provided for in the Multichannel Television
Sound (MTS) broadcast standard. A monaural soundtrack included within the
recorded or video signal (usually containing a second language translation for the
displayed program).
Sleep Timer
You can set a time period for which the TV will automatically turn itself off.
S-Video Input
You can connect your TV set to a high-resolution video source (such as Super
VHS video-cassette recorder, Laser Disc player and DVD Home Theater Set) in-
order to provide maximum consumer viewing satisfaction.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
|