321 Studiosr DMX5555z User Manual

Owner’s manual

Mode d’emploi

Manual de instrucciones

AM/FM CD/MD PLAYER WITH CD/MD

CHANGER CONTROL

•

RADIO AM/FM-LECTEUR CD/MD AVEC

PILOTAGE DE CHANGEUR CD/MD

•

RADIO DE AM/FM Y REPRODUCTOR DE CD/MD

CON CONTROL DE CAMBIADOR DE CD/MD

Clarion Co., Ltd.

PE-4018B

280-7323-00

Printed in Japan / Imprimé en Japon / Inpreso en Japón

1999/3 (To·K)

Download from Www.Somanuals.com. All Manuals Search And Download.

Functions of Remote Control Unit Buttons

Handling Compact Discs

2. PRECAUTIONS

Use only compact discs bearing the

mark.

Mode

CD changer

MD changer

Radio

1. When the inside of the car is very cold and

the player is used soon after switching on the

heater, moisture may form on the disc or the

optical parts of the player and proper play-

back may not be possible. If moisture forms

on the disc, wipe it off with a soft cloth.If mois-

ture forms on the optical parts of the player,

do not use the player for about one hour.The

condensation will disappear naturally allow-

ing normal operation.

2. Driving on extremely bumpy roads which

cause severe vibration may cause the sound

to skip.

Button

Do not play heart-shaped, octagonal, or other specially shaped compact discs.

£ FUNC

Turns power on and off. When pressed and held for 1 second:Turns power off.

Switches among radio, CD, MD, CD changer, MD changer and TV.

• To remove a compact disc from its storage

Handling

case, press down on the center of the case and

lift the disc out, holding it carefully by the edges.

• Do not use commercially available CD protec-

tion sheets or discs equipped with stabilizers,

etc. These may damage the disc or cause

breakdown of the internal mechanism.

3. This unit uses a precision mechanism. Even

in the event that trouble arises, never open

the case, disassemble the unit, or lubricate

the rotating parts.

• New discs may have some roughness around

the edges. If such discs are used, the player

may not work or the sound may skip. Use a

ball-point pen or the like to remove any rough-

ness from the edge of the disc.

¢ BAND

Plays the first

track.

Top play.

Moves the next

disc in

increasing

order.

Switches

reception band.

Plays the first

track.

Top play.

Switches

reception band.

DISC UP

PROG

TOP

Increases and decreases volume (in all modes).

;

VOLUME

Ball-point pen

Roughness

Moves preset

channels up

and down.

Moves tracks up

and down.

When pressed

and held for 1

second:

Moves tracks up

and down.

When pressed

and held for 1

second:

Moves tracks up Moves preset

and down.

When pressed

and held for 1

second:

Storage

§ SEARCH

channels up

and down.

This equipment has been tested and found to

comply with the limits for a Class B digital de-

vice, pursuant to Part 15 of the FCC Rules.

• Do not expose compact discs to direct sunlight

or any heat source.

• Do not expose compact discs to excess hu-

midity or dust.

• Do not expose compact discs to direct heat

from heaters.

CAUTION

USE OF CONTROLS, ADJUSTMENTS, OR

PERFORMANCE OF PROCEDURES OTHER

THAN THOSE SPECIFIED HEREIN, MAY RE-

SULT IN HAZARDOUS RADIATION EXPO-

SURE.

Fast-forward/

fast-backward.

Fast-forward/

fast-backward.

Fast-forward/

fast-backward.

These limits are designed to provide reasonable

protection against harmful interference in a resi-

dential installation.

Switches

between

playback and

pause.

No function.

Switches

between

playback and

pause.

Switches

between

playback and

pause.

No function.

¶ PLAY/PAUSE

• Never stick labels on the surface of the com-

pact disc or mark the surface with a pencil or

pen.

• Never play a compact disc with any cellophane

tape or other glue on it or with peeling off marks.

If you try to play such a compact disc, you may

not be able to get it back out of the CD player

or it may damage the CD player.

• Do not use compact discs that have large

scratches, are misshapen, cracked, etc. Use

of such discs may cause misoperation or dam-

age.

This equipment generates, uses, and can radi-

ate radio frequency energy and, if not installed

and used in accordance with the instructions,

may cause harmful interference to radio com-

munications.However, there is no guarantee that

interference will not occur in a particular instal-

lation.

Cleaning

THE COMPACT DISC PLAYER and MINI DISC

PLAYER SHOULD NOT BE ADJUSTED OR

REPAIRED BY ANYONE EXCEPT PROPERLY

QUALIFIED SERVICE PERSONNEL.

• To remove fingermarks and dust, use a soft

cloth and wipe in a straight line from the center

of the compact disc to the circumference.

• Do not use any solvents, such as commercially

available cleaners, anti-static spray or thinner

to clean compact discs.

• MUTE

ª ISR

Turns mute on and off.

Recalls ISR radio station in memory.

Press and hold for 2 seconds or longer: Stores current station into ISR memory (radio

mode only).

CHANGES OR MODIFICATIONS NOT EX-

PRESSLY APPROVED BY THE MANUFAC-

TURER FOR COMPLIANCE COULD VOID

THE USER’S AUTHORITYTO OPERATETHE

EQUIPMENT.

If this equipment does cause harmful interfer-

ence to radio or television reception, which can

be determined by turning the equipment off and

on, the user is encouraged to consult the dealer

or an experienced radio/TV technician for help.

• After using special compact disc cleaner, let

the compact disc dry off well before playing it.

Switches among main display, sub display and clock display.

º DISP

INFORMATION FOR USERS:.

Preset scan.

When pressed

and held for 2

seconds: Auto

store.

Scan play.

Preset scan.

When pressed

and held for 2

seconds: Auto

store.

⁄ SCN

When pressed

and held for 1

seconds: Disc

scan play.

CHANGES OR MODIFICATIONS TO THIS

PRODUCT NOT APPROVED BY THE MANU-

FACTURER WILL VOID THE WARRANTY

AND WILL VIOLATE FCC APPROVAL.

PS/AS

Handling Mini Discs

Use only MDs bearing the

mark.

MODEL

No function.

Repeat play.

Random play.

Repeat play.

When pressed

and held for 1

seconds: Disc

repeat play.

Repeat play.

Random play.

No function.

¤ RPT

If you try to play such a minidisc, you may not

be able to get it back out of the MD player or it

may damage the MD player.

Handling

• Never open the shutter on the MD cartridge.

BLS

12V

GROUND

AM 530-1710kHz/FM 87.9-107.9MHz

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC

RULES.OPERATION IS SUBJECT TO THE FOLLOWING

TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE

HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST

ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING

INTERFERENCE THAT MAY CAUSE UNDESIRED OPERA-

TION.

Storage

No function.

Random play.

When pressed

and held for 1

seconds: Disc

random play.

Switches

between TV and

VTR.

‹ RDM

DOLBY NR

MONI

• Do not expose minidiscs to direct sunlight or

any heat source.

• Do not expose minidiscs to excess humidity or

dust.

THIS PRODUCTION COMPLIES DHHS RULES 21 CFR

SUBCHAPTER J APPLICABLE AT DATE OF MANUFACTURE.

US AND FOREIGN PATENTS LICENSED FROM DOLBY

LABORATORIES LICENSING CORPORATION

CLARION CO.,LTD.

50 KAMITODA,TODA-SHI,SAITAMA-KEN,JAPAN

• Do not expose minidiscs to direct heat from

heaters.

MANUFACTURED:

* Some of the corresponding buttons on the source unit and remote control unit have different functions.

Shutter

286-

Clarion Co.,Ltd.

MADE IN

SERIAL No.

PE-

Cleaning

Cartridge

Bottom View of Source Unit

• If the MD cartridge is dirty, wipe off the dirt with

a soft dry cloth.

• Never play a minidisc with an index label that

is peeling off.

Be sure to unfold and read the next page.

Veuillez déplier et vous référer à la page suivante.

Cerciórese de desplegar y de leer la página siguiente.

Download from Www.Somanuals.com. All Manuals Search And Download._{DMX5 5 5 5 z}

DMX5 5 5 5 z

3. CONTROLS / LES COMMANDES / CONTROLES

5. REMOTE CONTROL

4. NOMENCLATURE

Note:

• Be sure to read this chapter referring to the front diagrams of chapter “3. CONTROLS” on page 5 (unfold).

Source unit / Appareil pilote / Unidad fuente

Names of Buttons

™

)

1 Preset buttons (1 to 6)

Direct buttons (1 to 6) (7 to 12)

2 Z-EHCR (z-enhancer) button

3 DISP (display) button

4 SPE-ANA (spectrum analyzer) button

5 SCN (scan) button

@ ENT (enter) button

Play/pause button

# TITLE button

Receiver for remote control unit

ADJ (adjust) button

$ MD EJECT button

% Left button

PS/AS (preset scan/auto store) button

6 RPT (repeat) button

¥ Right button

& Up button

Operating range: 30° in all directions

7 POWER button

* Down button

Remote control unit

Signal transmitter

FUNC (function) button

( A-M (audio mode) button

LOUD (loudness) button

) CD EJECT button

¡ CD insertion slot

™ MD insertion slot

8 RDM (random) button

9 ISR (instant station recall) button

0 MUTE button

! BAND (band) button

TOP button

;

•

456 78 9 0 ! @ # $% * ¥& (

‹

Display Items

⁄

1 CD IN indication

! MANU (manual) indication

@ LD (loudness) indication

# A-M (audio mode) indication

$ Function mode indication

2 SINGLE indication

Display / Afficheur / Visualizador

3 ST (stereo) indication

4 SCN (scan) indication

5 RPT (repeat) indication

6 RDM (random) indication

7 Operation status indication

∗ The names of modes being selected, etc. are

displayed.

Inserting the Batteries

3 456

8 9

1. Turn the remote control unit over, then slide

the rear cover in the direction of the arrow.

% Preset channel indication (1 to 6)

Disc number indication (1 to 12)

AA (UM-3/1.5V)

Batteries

∗ The frequency, play time, clock, etc. are

displayed.

2. Insert the AA (UM-3/1.5V) batteries that came

with the remote control unit facing in the di-

rections shown in the figure, then close the

rear cover.

∗ The disc numbers corresponding to the discs

in the CD or MD changer light.

8 CD/MD changer indication

9 Title scroll indication

0 MD IN indication

¥ Z-EHCR (z-enhancer) indication

& DISC indication

Notes:

Using batteries improperly can cause them to ex-

plode. Take note of the following points:

Rear cover

• When replacing batteries, replace both batteries

with new ones.

• Do not short-circuit, disassemble or heat batter-

ies.

Rear side

Note: Be sure to unfold this page and refer to the front diagrams as you read each chapter.

Remarque: Veuillez déplier cette page et vous référer aux schémas quand vous lisez chaque chapitre.

Nota: Cuando lea los capítulos, despliegue esta página y consulte los diagramas.

• Do not dispose of batteries into fire or water.

• Dispose of spent batteries properly.

_{DMX5 5 5 5 z}Download from Www.Somanuals.com. All Manuals Search And Download.

DMX5 5 5 5 z

6. OPERATIONS

Note: Be sure to read this chapter referring to the front diagrams of

chapter “3. CONTROLS” on page 5 (unfold).

Basic Operations

Radio mode ➜ CD mode ➜ MD mode ➜ CD

changer mode ➜ MD changer mode ➜ TV

mode ➜ Radio mode...

∗ External equipment not connected with CeNET

is not displayed.

CAUTION

Be sure to lower the volume before switching

off the unit power or the ignition key.The unit

remembers its last volume setting. If you

switch the power off with the volume up, when

you switch the power back on, the sudden

loud volume may hurt your hearing and dam-

age the unit.

Adjusting the volume

Press Up button & or Down button * increases

or decreases the volume.

The clock is displayed when the ignition key

is turned to the ACC (accessory) or IGN (igni-

tion-on) position even when the unit power

is off. In some cars, the clock may momen-

tarily disappear when the ignition key is

turned to the START position. The clock will

reappear after the engine has started and the

ignition key is released to the IGN (ignition-

on) position.

∗ The volume level is from 0 (minimum) to 33 (maxi-

mum).

Switching the display

Press DISP button 3 to select the desired dis-

play.

Each time you press DISP button 3, the display

switches in the following order:

Main display

Turning on/off the power

Notes:

• Be careful about using this unit for a long time with-

out running the engine. If you drain the car’s bat-

tery too far, you may not be able to start the en-

gine and this can reduce the service life of the

battery.

Sub (title) display

• System check

This unit checks what external equipment is con-

nected to the CeNET. The first time the ACC/Igni-

tion is turned on (initialization), “SYSTEM” and

“Push PWR” alternately blink in the display. Press

POWER button 7 to start the system check.When

complete, press POWER button 7 again to acti-

vate the unit.

Clock display

1. Press POWER button 7.

2. The illumination and display on the unit light

up. The unit automatically remembers its last

operation mode and will automatically switch

to display that mode.

Main display...

3. Press and hold POWER button 7 for 1 sec-

ond or longer to turn off the power for the unit.

Selecting a mode

1. Press FUNC button 7 to change the mode

of operation.

2. Each time you press FUNC button 7, the

mode of operation changes in the following

order:

DMX5 5 5 5 z

Download from Www.Somanuals.com. All Manuals Search And Download.

280 7323 00

Basic Operations

Turning on/off the loudness

The loudness effect emphasizes the bass and

treble to create a natural sound tone. When you

are listening to music at a low volume, it is rec-

ommended to use the loudness effect.

Radio Operations

∗ Once selected, the preferred display becomes

the display default.When a function adjustment

such as volume is made, the screen will

momentarily switch to that function’s display,

then revert back to the preferred display sev-

eral seconds after the adjustment.

Adjusting the treble

1. Press A-M button ( and select “TREB”.

FM reception

For enhanced FM performance the

^®tuner includes signal actuated

stereo control and Multipath noise reduction cir-

cuits.

2. Press Up button & to emphasize the treble,

or press Down button * to attenuate the

treble.

∗ When you have entered a title in a CD, it ap-

pears in the sub display. If you have not en-

tered a title, “USER TTL” appears in the title

display instead. For information on how to enter

a title, refer to the subsection “Entering titles”

in the “Other Handy Functions”.

∗ You can adjust the way of scrolling a title. For

the details on it, refer to the subsection

“Adjusting the way of scrolling” in the “Other

Handy Functions”.

1. Press and hold LOUD button ( for 1 second

or longer to turn on the loudness effect.When

the loudness effect is turned on, “LD” lights in

the display.

∗ The factory default setting is “0”. (Adjustment

range: −6 to +6)

3. When the adjustment is complete, press A-M

button ( several times until the function mode

is reached.

Changing the reception area

This unit is initially set to USA frequency intervals

of 10kHz for AM and 200kHz for FM.When using it

outside the USA, the frequency reception range

can be switched to the intervals below.

2. Press and hold LOUD button ( for 1 second

or longer to turn off the loudness effect. “LD”

goes off in the display.

➜➜Setting the reception area

Adjusting the balance

1. Press A-M button ( and select “BAL”.

1. Press FUNC button 7 and select the radio

mode (FM or AM).

2. Press Up button & to emphasize the sound

from the right speaker, or press Down button

* to emphasizes the sound from the left

speaker.

2. While pressing RDM button 8, each time you

press and hold the number “1” of the Preset

buttons 1 for 2 seconds or longer, the recep-

tion area switches from inside the USA to out-

side the USA or from outside the USA to in-

side the USA.

Setting the Z-enhancer

This unit comes with 3 types of sound tone effects

stored in memory. Select the one you prefer.

∗ The factory default setting is “0”. (Adjustment

range: L13 to R13)

∗ The factory default setting is “OFF”.

Each time you press Z-EHCR button 2, the tone

effect changes in the following order:

3. When the adjustment is complete, press A-M

button ( several times until the function mode

is reached.

∗ Any station preset memories are lost when the

reception area is changed.

“Z-EHCR 1” ➜ “Z-EHCR 2” ➜ “Z-EHCR 3” ➜

“OFF” ➜ “Z-EHCR 1”...

Listening to the radio

1. Press FUNC button 7 and select the radio

• Z-EHCR 1 : bass emphasized

Adjusting the fader

1. Press A-M button ( and select “FAD”.

• Z-EHCR 2 : treble emphasized

• Z-EHCR 3 : bass and treble emphasized

mode.

2. Press Up button & to emphasize the sound

from the front speakers, or press Down but-

ton * to emphasize the sound from the rear

speakers.

2. Press BAND button ! and select the radio

band. Each time the button is pressed, the

radio reception band changes in the following

order:

• OFF

: no sound effect

Adjusting the tone

Press A-M button ( and select the item to ad-

just. Each time you press A-M button (, the item

changes in the following order:

∗ The factory default setting is “0”. (Adjustment

range: F12 to R12)

FM1 ➜ FM2 ➜ FM3 ➜ AM ➜ FM1...

3. Press Right button ¥ or Left button % to tune

3. When the adjustment is complete, press A-M

button ( several times until the function mode

is reached.

in the desired station.

➜➜When the Z-enhancer is off

“BASS” ➜ “TREB” ➜ “BAL” ➜ “FAD” ➜

Function mode...

Tuning

There are 3 types of tuning mode available, seek

tuning, manual tuning and preset tuning.

Adjusting the Z-enhancer

1. Press Z-EHCR button 2 and select the Z-

➜➜When Z-enhancer 1, 2 or 3 is set

“Z-EHCR” ➜ “BAL” ➜ “FAD” ➜ Function

mode...

enhancer mode (1 to 3) to adjust.

Seek tuning

1. Press BAND button ! and select the desired

2. Press A-M button ( and select “Z-EHCR”.

3. Press Up button & or Down button * to ad-

Adjusting the bass

1. Press A-M button ( and select “BASS”.

band (FM or AM).

just Z-enhancer.

∗ If “MANU” is lit in the display, press and hold

BAND button ! for 1 second or longer.“MANU”

in the display goes off and seek tuning is now

available.

∗ When Z-enhancer 1 is selected, you can adjust

the bass in the range of ±2.

∗ When Z-enhancer 2 is selected, you can adjust

the treble in the range of ±2.

∗ When Z-enhancer 3 is selected, you can adjust

the bass and treble in the range of ±2.

2. Press Up button & to emphasize the bass,

or press Down button * to attenuate the bass.

∗ The factory default setting is “0”. (Adjustment

range: −6 to +6)

3. When the adjustment is complete, press A-M

button ( several times until the function mode

is reached.

2. Press Right button ¥ or Left button % to au-

tomatically seek to the next station.

When Right button ¥ is pressed, the station

is sought in the direction of higher frequencies;

if Left button % is pressed, the station is

sought in the direction of lower frequencies.

4. When the adjustment is complete, press A-M

button ( several times until the function mode

is reached.

DMX5 5 5 5 z

Download from Www.Somanuals.com. All Manuals Search And Download.

280 7323 00

Radio Operations

Manual tuning

There are 2 ways available:Quick tuning and step

tuning.

When you are in the step tuning mode, the

frequency changes one step at a time. In quick

tuning mode, you can quickly tune the desired

frequency.

1. Press BAND button ! and select the desired

band (FM or AM).

CD Operations

Notes:

Recalling a preset station

Pressing the corresponding preset button recalls

the stored radio frequency automatically.

Loading a CD

Insert a CD into the center of the insertion slot

with the label side facing up. The CD plays

automatically after loading.

• If you force a CD into before auto reloading,

this can damage the CD.

∗ The radio mode is selected automatically 4 seconds

after CD EJECT button ) is pressed.

1. Press BAND button ! and select the desired

Notes:

band (FM1, FM2, FM3 or AM).

• Never insert foreign objects into the CD insertion

slot.

• When a CD is loaded in the unit, CD IN indication

1 lights in the display. Never try to insert another

CD in this case.

2. Press the corresponding Preset button 1 to

Selecting a track

➜➜Track-up

recall the stored station.

∗ Press and hold one of the Preset buttons 1

for 2 seconds or longer to store that station into

preset memory.

1. Press Right button ¥ to move ahead to the

beginning of the next track.

∗ If “MANU” is not lit in the display, press and

hold BAND button ! for 1 second or longer.

“MANU” lights in the display and manual tuning

is now available.

• Discs not bearing the

cannot be played by this unit.

mark and CD-ROMs

2. Each time you press Right button ¥, the track

advances ahead to the beginning of the next

track.

Preset scan

Preset scan receives the stations stored in preset

memory in order. This function is useful when

searching for a desired station in memory.

2. Tune into a station.

Loading 3" (8 cm) compact discs

➜➜Track-down

➜ Quick tuning:

∗ No adapter is required to play a 3" CD.

∗ Insert the 3" CD into the center of the insertion

slot.

∗ When a 3" CD is loaded, “SINGLE” lights in the

display.

1. Press Left button % to move back to the be-

Press and hold Right button ¥ or Left button

% for 1 second or longer to manually tune to

the desired frequency.

ginning of the current track.

1. Press PS button 5.

2. Press Left button % twice to move to the be-

2. When a desired station is tuned in, press PS

button 5 again to continue receiving that sta-

tion.

ginning of the previous track.

➜ Step tuning:

Press Right button ¥ or Left button % to

manually tune one step at a time to the de-

sired frequency.

Fast-forward/fast-backward

➜➜Fast-forward

Listening to a CD already inserted

Note:

• Be careful not to press and hold PS button 5 for

2 seconds or longer, otherwise the auto store func-

tion engages and the unit starts storing stations.

Press FUNC button 7 to select the CD mode.

Play starts automatically. If no CD is loaded in

the unit, “NO DISC” appears in the display.

Press and hold Right button ¥ for 1 second or

longer.

Storing a preset station

A total of 24 preset positions (6-FM1, 6-FM2, 6-

FM3, 6-AM) exists to store individual radio

stations in memory.

➜➜Fast-backward

Instant station recall (ISR)

Pausing play

1. Press Play/pause button @ to pause play.

“PAUSE” appears in the display.

Press and hold Left button % for 1 second or

longer.

Instant station recall is a special radio preset that

instantly accesses a favorite radio station at a

touch of a button.The ISR function even operates

with the unit in other modes.

2. To resume CD play, press Play/pause button

Top function

The top function resets the CD player to the first

track of the disc. Press TOP button ! to play the

first track (track No. 1) on the disc.

Manual memory

1. Select the desired station with seek tuning,

manual tuning or preset tuning.

@ again.

➜ ISR memory

1. Select the station that you wish to store in ISR

memory.

Displaying CD titles

This unit can display title data for user titles input

with this unit.

2. Press and hold one of Preset buttons 1 for 2

seconds or longer to store the current station

into preset memory.

2. Press and hold ISR button 9 for 2 seconds

Scan play

The scan play locates and plays the first 10

seconds of each track on a disc automatically.This

function continues on the disc until it is canceled.

or longer.

Press DISP button 3 to display the title.

➜ Recalling a station with ISR

Notes:

Auto store

In any mode, press ISR button 9 to turn on the

radio function and tune the selected radio sta-

tion. “ISR” appears in the display. Press ISR but-

ton 9 again to return to the previous mode.

• Titles of CD-text CDs cannot be displayed with this

unit.

• If the CD playing is a CD-text CD or no user title

has been input, “USERTTL” appears in the display.

Auto store selects up to 6 stations and

automatically stores them into preset memory. If

auto store cannot tune in all six stations, then it

stores the strongest stations into memory and

the other presets untouched.

∗ The scan play is useful when you want to select a

desired track.

1. Press SCN button 5 to start track scanning.

“SCN” lights in the display.

Ejecting a CD

Press CD EJECT button ) to eject the CD.Take

it out from the ejected position.

2. To cancel the scan play, press SCN button 5

again. “SCN” goes off from the display and

the current track continues to play.

1. Press BAND button ! and select the desired

band (FM or AM).

2. Press and hold AS button 5 for 2 seconds or

longer. The stations with good reception are

stored automatically to the preset buttons.

∗ If a 5" CD (12 cm) is left in the ejected position for

15 seconds, the CD is automatically reloaded (Auto

reload).

∗ 3" CDs (8 cm) are not auto reloaded. Be sure to

remove it when ejected.

DMX5 5 5 5 z

Download from Www.Somanuals.com. All Manuals Search And Download.

280 7323 00

CD Operations

Repeat play

MD Operations

Loading an MD

Selecting a track

Random play

The repeat play continuously plays the current

track. This function continues automatically until

it is canceled.

After confirming the orientation of an MD, insert

the MD into the insertion slot.

➜➜Track-up

The random play selects and plays individual tracks

on a disc in no particular order. This function

continues automatically until it is canceled.

1. Press Right button ¥ to move ahead to the

Notes:

beginning of the next track.

• Never insert foreign objects into the MD insertion

slot.

• When an MD is loaded in the unit, MD IN indica-

tion 0 lights in the display. Never try to insert an-

other MD in this case.

1. Press RPT button 6. “RPT” lights in the dis-

1. Press RDM button 8. “RDM” lights in the dis-

play, an individual track is selected randomly

and play begins.

2. Each time you press Right button ¥, the track

advances ahead to the beginning of the next

track.

play and the current track is repeated.

2. To cancel the repeat play, press RPT button

6 again.“RPT” goes off from the display and

normal play resumes.

2. To cancel the random play, press RDM but-

ton 8 again.“RDM” goes off and normal play

resumes.

➜➜Track-down

• An MD that does not carry the

mark cannot

1. Press Left button % to move back to the be-

be used with this unit.

ginning of the current track.

Random play

The random play selects and plays individual tracks

on a disc in no particular order. This function

continues automatically until it is canceled.

2. Press Left button % twice to move to the be-

Listening to an MD already inserted

Press FUNC button 7 to select the MD mode.

Play starts automatically. If no MD is loaded in

the unit, “NO DISC” appears in the display.

ginning of the previous track.

Fast-forward/fast-backward

➜➜Fast-forward

1. Press RDM button 8. “RDM” lights in the dis-

play, an individual track is selected randomly

and play begins.

Press and hold Right button ¥ for 1 second or

longer.

Pausing play

1. Press Play/pause button @ to pause play.

“PAUSE” appears in the display.

2. To cancel the random play, press RDM but-

ton 8 again.“RDM” goes off from the display

and normal play resumes.

➜➜Fast-backward

Press and hold Left button % for 1 second or

longer.

2. To resume MD play, press Play/pause button

@ again.

Top function

Switching between a disc title and

a track title

On this unit, a disc title and a track title that have

been previously entered can be displayed.

The top function resets the MD player to the first

track of the disc. Press TOP button ! to play the

first track (track No. 1) on the disc.

∗ Titles cannot be entered for MDs with this unit.

1. Press DISP button 3 to display the title.

Scan play

The scan play locates and plays the first 10 sec-

onds of each track on a disc automatically. This

function continues on the disc until it is canceled.

2. Each time you press and hold DISP button

3 for 1 second or longer, the display toggles

between the disc title and the track title.

∗ The scan play is useful when you want to select a

desired track.

Notes:

•

If an MD is not input its disc title or a track title,

“D TITLE” or “T TITLE” appears in the display.

1. Press SCN button 5 to start track scanning.

“SCN” lights in the display.

∗ You can adjust the way of scrolling a title. For the

details on it, refer to the subsection “Adjusting

the way of scrolling” in the “Other Handy

Functions”.

2. To cancel the scan play, press SCN button 5

again. “SCN” goes off from the display and

the current track continues to play.

Repeat play

Ejecting an MD

The repeat play continuously plays the current

track. This function continues automatically until

it is canceled.

Press MD EJECT button $ to eject an MD.Take

it out from the ejected position.

∗ The radio mode is selected automatically 4

seconds after MD EJECT button $ is pressed.

1. Press RPT button 6. “RPT” lights in the dis-

play and the current track is repeated.

2. To cancel the repeat play, press RPT button

6 again. “RPT” goes off from the display and

normal play resumes.

DMX5 5 5 5 z

Download from Www.Somanuals.com. All Manuals Search And Download.

280 7323 00

Other Handy Functions

4. Press ADJ button

mode.

to return to the previous

7. Press Right button ¥ or Left button % to se-

lect the desired character.Pressing Right but-

ton ¥ moves the cursor to the next charac-

ter; pressing Left button % moves the cursor

to the previous character.

Setting the clock

1. Press and hold ADJ button # for 1 second or

longer to switch to the adjustment selection

display.

Adjusting the display contrast

You can adjust the display contrast according to

the angle of installation of the unit.

Setting the speed of the spectrum

analyzer display

∗ The factory default setting is “HIGH”.

∗ The factory default setting is “LEVEL 6”. (Adjust-

ment level: 1 to 11)

2. Press Right button ¥ or Left button % to se-

lect “CLOCK”.

8. Repeat steps 5 to 7 to enter up to 10

characters for the title.

1. Press and hold ADJ button # for 1 second or

longer to switch to the adjustment selection

display.

1. Press and hold ADJ button

for 1 second or

3. Press ENT button @.

9. Press and hold ENT button @ for 2 seconds

or longer to store the title into memory and

cancel title input mode.

longer to switch to the adjustment selection

display.

4. Press Right button ¥ or Left button % to se-

2. Press Right button ¥ or Left button % to se-

lect “CONTRAST”.

lect the hour or the minute.

2. Press Right button ¥ or Left button % to se-

lect “ANA SPD”.

5. Press Up button & or press Down button *

3. Press Up button & or Down button * to ad-

to set the correct time.

Clearing titles

1. Play a CD or a CD in a CD changer, or tune a

radio station or TV station that you want to

clear the title for.

just the contrast.

3. Press Up button & or Down button * to set

∗ The clock is displayed in 12-hour format.

the speed of the spectrum analyzer display.

4. Press ADJ button # to return to the previous

6. Press ENT button

to store the time into memory.

mode.

You can choose one of “LOW”, “MID” or

“HIGH” for the speed of the spectrum analyzer

display.

7. Press ADJ button # to return to the previous mode.

Note:

2. Press DISP button 3 and display the sub-

Message display

When the unit is powered on or off, a message is

displayed.The user can turn this message display

on or off.

• You cannot set the clock when it is displayed with

only the ignition on. If you drain or remove the car’s

battery or take out this unit, the clock is reset.While

setting the clock, if another button or operation is

selected, the clock set mode is canceled.

title.

4. Press ADJ button

mode.

to return to the previous

3. Press TITLE button #. “TITL” appears in the

display and the display switches to the title

input display.

Entering titles

∗ The factory default setting is “ON”.

1. Press and hold ADJ button # for 1 second or

longer to switch to the adjustment selection

display.

4. Press BAND button !.

Titles up to 10 characters long can be stored in

memory and displayed for radio or TV stations

and CDs. The numbers of titles that can be

entered for each mode are as follows.

Switching the spectrum analyzer

display patterns

You can select one out of 4 patterns or set it to

off.

∗ The factory default setting is “PATTERN 1”.

Each time you press SPE-ANA button 4, the

spectrum analyzer display pattern changes in the

following order:

5. Press and hold ENT button @ for 2 seconds

or longer to clear the title and cancel the title

input mode.

2. Press Right button ¥ or Left button % to se-

lect “MESSAGE”.

Mode

Number of titles

30 titles

Adjusting the way of title scrolling

There are 3 ways for scrolling a title in the dis-

play.You can select the way you prefer.

3. Press Up button & to set the message dis-

play to “ON”; press Down button * to set the

message display to “OFF”.

Radio mode

CD mode

TV mode

100 titles

15 titles

∗ The factory default setting is “AUTO”.

1. Press and hold ADJ button # for 1 second or

longer to switch to the adjustment selection

display.

5. Press ADJ button # to return to the previous

PATTERN 1 ➜ PATTERN 2 ➜ PATTERN 3 ➜

PATTERN 4 ➜ OFF ➜ PATTERN 1...

Note:

The spectrum analyzer display is unavailable dur-

ing these operations below;

• Seek tuning and auto store in radio mode.

• Mute or pause.

CD changer mode

CDC655z connected

CDC655Tz connected

CDC1255z connected

Number of titles

60 titles

mode.

Triggered audio mute for cellular

telephones

This unit requires special wiring to mute the audio

signal automatically when a cellular telephone

rings in the car.

100 titles

2. Press Right button ¥ or Left button % to se-

lect “SCROLL”.

50 titles

1. Press FUNC button 7 to select the mode you

want to enter a title. (radio, CD, CD changer or

TV)

3. Press Up button & or Down button * to

change the display. Each time Up button &

or Down button * is pressed, the display

changes among the 3 display methods avail-

able.

• When “NO DISC” or an error message appears

in the display.

∗ This function is not compatible with all cellular

telephones. Contact your local authorized Clarion

dealer for information on proper installation and

compatibility.

∗ Titles cannot be entered for MDs with this unit.

2. Select and play a CD or a CD in the CD changer,

or tune to an appropriate TV or radio station.

Setting the sensitivity of the spec-

trum analyzer

∗ The factory default setting is “MID”.

AUTO:

3. Press DISP button 3 and display the title.

The title automatically scrolls over and over

again.

4. Press TITLE button

#. “TITL” appears in the

1. Press and hold ADJ button

for 1 second or

display and the cursor position flashes.

1-TIME:

longer to switch to the adjustment selection

display.

5. Press Right button ¥ or Left button % to move

A title scrolls once. To have title scroll again,

press TITLE button #.

the cursor.

2. Press Right button ¥ or Left button % to se-

lect “ANA SENS”.

6. Press DISP button 3 to select a character.

Each time you press DISP button 3, the char-

acter changes in the following order:

MANUAL:

3. Press Up button & or Down button * to set

You must press TITLE button # to scroll the

display.

the sensitivity of the spectrum analyzer.

Capital letters ➜ Small letters ➜ Numbers/

Symbols ➜ Capital letters...

You can choose one of “LOW”, “MID” or

“HIGH” for the sensitivity of the spectrum ana-

lyzer.

4. Press ADJ button # to return to the previous

mode.

DMX5 5 5 5 z

Download from Www.Somanuals.com. All Manuals Search And Download.

280 7323 00

CD Changer Operations

7. OPERATIONS OF ACCESSORIES

CD Changer Operations

Top function

The top function plays from the first track (track

No. 1) of the disc.

Repeat play

The repeat play continuously plays the current

track.This function continues automatically until it

is canceled.

➜➜When playing a disc 1 to 6

CD changer functions

Selecting a CD

1. Press RPT button 6. “RPT” lights in the dis-

Press the Direct button 1 (1 to 6) with the same

number as the CD playing.

When an optional CD changer is connected

through the CeNET cable, this unit controls all

the CD changer functions.This unit can control a

total of 2 changers (MD and/or CD).

Each of the Direct button 1 corresponds to a

disc loaded into the magazine.

play and the current track is repeated.

2. To cancel the repeat play, press RPT button

6 again.“RPT” goes off from the display and

normal play resumes.

➜ When playing a disc 7 to 12 (only when a

12 disc CD changer is used.)

➜➜Selecting a disc from 1 to 6

Press the corresponding Direct button 1 (1 to

Press and hold for 1 second or longer the Direct

button 1 (7 to 12) with the same number as the

CD playing.

Press FUNC button 7 and select the CD changer

mode to start play. If 2 CD changers are

connected, press FUNC button 7 to select the

CD changer for play.

6) to select the desired disc.

➜ Selecting a disc from 7 to 12 (only when a

12 disc CD changer is used.)

Disc repeat play

After all the tracks on the current disc have been

played, the disc repeat play automatically replays

the current disc over from the first track. This

function continues automatically until it is

canceled.

∗ If a CD is not loaded in a slot of the magazine,

pressing the Direct button 1 corresponding to its

disc number is invalid.

Press and hold the corresponding Direct button

1 (7 to 12) for 1 second or longer to select the

desired disc.

∗ If “NO MAGA” appears in the display, insert the

magazine into the CD changer. “CHECK” appears

in the display while the player loads (checks) the

magazine.

∗ If “NO DISC” appears in the display, eject the

magazine and insert discs into each slot. Then,

reinsert the magazine back into the CD changer.

∗ If a CD is not loaded in a slot of the magazine,

pressing the Direct button 1 corresponding to its

disc number is invalid.

Scan play

1. Press and hold RPT button 6 for 1 second

or longer. DISC indication & and “RPT” light

in the display and the disc repeat play starts.

The scan play locates and plays the first 10

seconds of each track on a disc automatically.

This function continues on the disc until it is

canceled.

Selecting a track

➜➜Track-up

2. To cancel the disc repeat play, press and hold

RPT button 6 again. DISC indication & and

“RPT” go off from the display and normal play

resumes on the current track.

CAUTION

∗ The scan play is useful when you want to select a

desired track.

1. Press Right button ¥ to move ahead to the

CD-ROM discs cannot be played in the CD

changer.

beginning of the next track.

1. Press SCN button 5 to start track scanning.

“SCN” lights in the display.

2. Each time you press Right button ¥, the track

advances ahead to the beginning of the next

track.

2. To cancel the scan play, press SCN button 5

again. “SCN” goes off from the display and

the current track continues to play.

Pausing play

1. Press Play/pause button @ to pause play.

“PAUSE” appears in the display.

Random play

The random play selects and plays individual

tracks on the disc in no particular order. This

function continues automatically until it is

canceled.

➜➜Track-down

1. Press Left button % to move back to the be-

2. To resume play, press Play/pause button @

Disc scan play

ginning of the current track.

again.

The disc scan play locates and plays the first 10

seconds of the first track on each disc in the

currently selected CD changer. This function

continues automatically until it is canceled.

1. Press RDM button 8. “RDM” lights in the dis-

2. Press Left button % twice to move to the be-

play and the random play begins.

ginning of the previous track.

Displaying CD titles

This unit can display title data for CD-text CDs

and user titles input with this unit.

2. To cancel the random play, press RDM but-

ton 8 again.“RDM” goes off from the display

and normal play resumes.

Fast-forward/fast-backward

➜➜Fast-forward

∗ The disc scan play is useful when you want to

select a desired CD.

1. Press and hold SCN button 5 for 1 second

or longer. DISC indication & and “SCN” light

in the display and the disc scan play starts.

∗ Title data for CD-text CDs can be displayed with

this unit only when it is connected to CDC655Tz.

➜➜When connected to CDC655z or CDC1255z

Press DISP button 3 to display the title.

➜➜When connected to CDC655Tz

Press and hold Right button ¥ for 1 second or

longer.

Disc random play

The disc random play selects and plays individual

tracks or discs automatically in no particular

order.This function continues automatically until

it is canceled.

➜➜Fast-backward

Press and hold Left button % for 1 second or

longer.

2. To cancel the disc scan play, press SCN but-

ton 5 again. DISC indication & and “SCN”

go off from the display and the current track

continues to play.

1. Press DISP button 3 to display the title.

2. Each time you press and hold DISP button

3 for 1 second or longer, the title display

changes in the following order:

1. Press and hold RDM button 8 for 1 second

or longer. DISC indication & and “RDM” light

in the display and the disc random play starts.

User title (disc) ➜ CD-text title (disc) ➜ CD-

text title (track) ➜ user title (disc)...

Notes:

• If the CD playing is not a CD-text CD or no user

title has been input, “USER TTL” appears in the

display.

2. To cancel the disc random play, press and hold

RDM button 8 again.DISC indication & and

“RDM” go off from the display and normal play

resumes from the current track.

• If a CD-text CD is not input its disc title or a track

title, “TEXTDTTL” or “TEXTTTTL” appears in the

display.

DMX5 5 5 5 z

Download from Www.Somanuals.com. All Manuals Search And Download.

280 7323 00

MD Changer Operations

Repeat play

TV Operations

➜➜Track-down

MD changer functions

TV tuner functions

1. Press Left button % to move back to the be-

When an optional MD changer is connected

through the CeNET cable, this unit controls all

the MD changer functions. This unit can control

a total of 2 changers (MD and/or CD).

The repeat play continuously plays the current

track. This function continues automatically until

it is canceled.

When an optional TV tuner is connected through

the CeNET cable, this unit controls all TV tuner

functions. To watch TV requires a TV tuner and

monitor.

ginning of the current track.

2. Press Left button % twice to move to the be-

ginning of the previous track.

1. Press RPT button 6. “RPT” lights in the dis-

Press FUNC button 7 and select the MD changer

mode to start play. If 2 MD changers are con-

nected, press FUNC button 7 to select the MD

changer for play.

play and the current track is repeated.

Watching a TV

1. Press FUNC button 7 and select the TV

Fast-forward/fast-backward

➜➜Fast-forward

2. To cancel the repeat play, press RPT button

6 again. “RPT” goes off from the display and

normal play resumes.

mode.

Press and hold Right button ¥ for 1 second or

longer.

∗ If “NO DISC” appears in the display, load MDs into

the MD changer.

2. Press BAND button ! to select the desired

TV band (TV1 or TV2). Each time the button

is pressed, the input selection toggles

between TV1 and TV2.

Disc repeat play

➜➜Fast-backward

After all the tracks on the current disc have been

played, the disc repeat play automatically replays

the current disc over from the first track. This

function continues automatically until it is

canceled.

Press and hold Left button % for 1 second or

longer.

Pausing play

1. Press Play/pause button @ to pause play.

“PAUSE” appears in the display.

3. Press Right button ¥ or Left button % to tune

in the desired TV station.

Top function

2. To resume play, press Play/pause button @

The top function plays from the first track (track

No. 1) of the disc. Press the Direct button 1 (1

to 6) with the same number as the MD playing.

again.

1. Press and hold RPT button 6 for 1 second

or longer. DISC indication & and “RPT” light

in the display and the disc repeat play starts.

Watching a video

The TV tuner has a VTR input terminal to which

1 external device can be connected. Connect a

12V video cassette player (VCP) or video

cassette recorder (VCR) to the TV tuner input

terminal.

Switching disc titles and track titles

This unit can display disc titles and track titles

already entered on MDs.

∗ If an MD is not loaded in a slot of the MD changer,

pressing the Direct button 1 corresponding to its

disc number is invalid.

2. To cancel the disc repeat play, press and hold

RPT button 6 again. DISC indication & and

“RPT” go off from the display and normal play

resumes on the current track.

∗ Titles cannot be entered for MDs with this unit.

1. Press DISP button 3 to display the title. The

disc title or track title is displayed.

1. Press RDM button 8 to select VTR.

Scan play

The scan play locates and plays the first 10 sec-

onds of each track on a disc automatically. This

function continues on the disc until it is canceled.

2. To return to the TV broadcast, press RDM

Random play

2. Each time you press and hold DISP button

3 for 1 second or longer, the display toggles

between the disc title and the track title.

button 8.

The random play selects and plays individual

tracks on the disc in no particular order. This

function continues automatically until it is

canceled.

Tuning

∗ The scan play is useful when you want to select a

desired track.

1. Press SCN button 5 to start track scanning.

“SCN” lights in the display.

Note:

There are 3 types of tuning mode available, seek

tuning, manual tuning and preset tuning.

• If an MD is not input its disc title or a track title,

“D TITLE” or “T TITLE” appears in the display.

1. Press RDM button 8. “RDM” lights in the dis-

play and the random play begins.

2. To cancel the scan play, press SCN button 5

again. “SCN” goes off from the display and

the current track continues to play.

Seek tuning

1. Press BAND button ! and select the desired

Selecting an MD

2. To cancel the random play, press RDM but-

ton 8 again. “RDM” goes off from the display

and normal play resumes.

Each of the Direct button 1 corresponds to an

MD loaded into the MD changer. Press the

corresponding Direct button 1 (1 to 6) to select

the desired disc.

TV band (TV1 or TV2).

∗ If “MANU” is lit in the display, press and hold

BAND button ! for 1 second or longer.“MANU”

in the display goes off and seek tuning is now

available.

Disc scan play

Disc random play

The disc scan play locates and plays the first 10

seconds of the first track on each disc in the

currently selected MD changer. This function

continues automatically until it is canceled.

∗ If an MD is not loaded in a slot of the MD changer,

pressing the Direct button 1 corresponding to its

disc number is invalid.

The disc random play selects and plays individual

tracks or discs automatically in no particular

order.This function continues automatically until

it is canceled.

2. Press Right button ¥ or Left button % to au-

tomatically seek to the next station.

Press Right button ¥ to automatically tune

up the frequency band to the next available

TV station; press Left button % to automati-

cally tune down.

∗ The disc scan play is useful when you want to se-

lect a desired MD.

1. Press and hold SCN button 5 for 1 second

or longer. DISC indication & and “SCN” light

in the display and the disc scan play starts.

Selecting a track

➜➜Track-up

1. Press and hold RDM button 8 for 1 second

or longer. DISC indication & and “RDM” light

in the display and the disc random play starts.

1. Press Right button ¥ to move ahead to the

beginning of the next track.

2. To cancel the disc random play, press and hold

RDM button 8 again. DISC indication & and

“RDM” go off from the display and normal play

resumes from the current track.

2. Each time you press Right button ¥, the track

advances ahead to the beginning of the next

track.

2. To cancel the disc scan play, press and hold

SCN button 5 again. DISC indication & and

“SCN” go off from the display and the current

track continues to play.

DMX5 5 5 5 z

Download from Www.Somanuals.com. All Manuals Search And Download.

280 7323 00

TV Operations

Manual tuning

8. TROUBLESHOOTING

Auto store

There are 2 ways available:Quick tuning and step

tuning.

Auto store selects 6TV stations automatically and

stores each one into a preset memory.

Problem

Cause

Measure

Power does not

turn on.

(No sound is

produced.)

Fuse is blown.

Replace with a fuse of the same amperage. If the

fuse blows again, consult your store of purchase.

When you are in the step tuning mode, the

frequency changes one step at a time. In quick

tuning mode, you can quickly tune the desired

frequency.

If there are not 6 stations with good reception,

stations previously stored in memory remain and

only the strong stations are stored into memory.

Incorrect wiring.

Consult your store of purchase.

1. Press BAND button ! and select the desired

No sound output

when operating

the unit with

amplifiers or

power antenna

attached.

Power antenna lead is

shorted to ground or

excessive current is required

for remote-on the amplifiers

or power antenna.

1. Turn the unit off.

1. Press BAND button ! and select the desired

TV band (TV1 or TV2).

2. Remove all wires attached to the power antenna

lead. Check each wire for a possible short to

ground using an ohm meter.

band (TV1 or TV2).

2. Press and hold AS button 5 for 2 seconds or

longer. The stations with good reception are

automatically stored to the Preset buttons 1.

∗ If “MANU” is not lit in the display, press and

hold BAND button ! for 1 second or longer.

“MANU” lights in the display and manual tun-

ing is now available.

3. Turn the unit back on.

4. Reconnect each amplifier remote wire to the

power antenna lead one by one. If the amplifiers

turn off before all wires are attached, use an

external relay to provide remote-on voltage

(excessive current required).

Preset scan

2. Tune into a station.

Preset scan allows the user to view each preset

position before it automatically advances to the

next preset. This function is useful for searching

for a desired TV station in memory.

➜ Quick tuning:

Press and hold Right button ¥ or Left button

% for 1 second or longer to quickly tune up

and down to a desired station.

Nothing happens The microprocessor has

when buttons are malfunctioned due to noise,

pressed.

Press the reset button with a thin rod.

etc.

Reset button

1. Press PS button 5.

➜ Step tuning:

Display is not

accurate.

2. When a desired station is found, press PS

button 5 again to remain tuned to that sta-

tion.

Press Right button ¥ or Left button % to

manually tune to a station, one channel at a

time.

Note:

• Do not press and hold PS button 5 for 2 seconds

or longer. Doing so will trigger the auto store

function and start storing stations into memory.

Recalling a preset station

A total of 12 TV stations can be stored (6-TV1

and 6-TV2).This allows you to select your favorite

TV stations and store them in memory for later

recall.

CD cannot be

loaded.

Another CD is already

loaded.

Eject the CD before loading the new one.

Setting the receiver for Diversity

tuning

You can change the reception setting for the TV

antenna connected to the TV tuner.

Sound skips or is CD is dirty.

noisy.

Clean the CD with a soft cloth.

1. Press BAND button ! and select the desired

CD is heavily scratched or

warped.

Replace with a CD with no scratches or no warped.

TV band (TV1 or TV2).

∗ The factory default setting is “ON”.

1. Press and hold ADJ button # for 1 second or

longer to switch to the adjustment selection

display.

2. To recall a storedTV station, press the desired

Sound is bad

directly after

power is turned

on.

Water droplets may form on Let it dry for about 1 hour with the power on.

Preset button 1 to select that station.

the internal lens when the

car is parked in a humid

place.

∗ Press and hold one of the Preset buttons 1

for 2 seconds or longer to store the current sta-

tion into the preset memory.

2. Press Right button ¥ or Left button % to se-

lect “TV DIVER”.

MD cannot be

loaded.

Another MD is already

loaded.

Eject the MD before loading the new one.

Insert correctly.

Manual memory

1. Select the desired station with seek tuning,

manual tuning or preset tuning.

3. Press Up button & to set to “ON” or Down

button * to set to “OFF”.

MD is immediately MD inserted wrongly.

ejected.

ON:

Non-recorded MD is loaded. Replace with a pre-recorded MD.

2. Press and hold one of the Preset buttons 1

for 2 seconds or longer to store the current

station to that preset memory.

In the “ON” position, the TV tuner emphasizes

the visual signal by choosing the antenna with

the best signal strength. This requires more

than one antenna on the vehicle.

Sound skips or is MD is heavily scratched or

noisy.

Replace with an MD with no scratches or no warped.

warped.

Sound is bad

directly after

power is turned

on.

Water droplets may form on Let it dry for about 1 hour with the power on.

OFF:

the internal lens when the

car is parked in a humid

place.

Set the TV Diver adjustment to the “OFF” po-

sition when only using one antenna on the

vehicle.

4. Press ADJ button # to return to the previous

mode.

DMX5 5 5 5 z

Download from Www.Somanuals.com. All Manuals Search And Download.

280 7323 00

9. ERROR DISPLAYS

If an error occurs, one of the following displays is displayed.

Take the measures described below to eliminate the problem.

10. SPECIFICATIONS

FM Tuner

Audio

Frequency Range:

Maximum Power Output:

87.9 MHz to 107.9 MHz

160 W (40 W × 4 ch) (EIAJ)

Continuous Average Power Output:

14 W × 4, into 4 Ω, 20 Hz to 20 kHz, 1%THD

Bass Control Action (30 Hz):

Error Display

ERROR 2

Cause

Measure

Usable Sensitivity:

11 dBf

A CD is caught inside the CD deck and is

not ejected.

This is a failure of CD deck’s mechanism

and consult your store of purchase.

50dB Quieting Sensitivity:

17 dBf

±15 dB

ERROR 3

ERROR 2

ERROR 3

ERROR 2

ERROR 3

ERROR 6

ERROR H

A CD cannot be played due to scratches,

etc.

Replace with a non-scratched, non-warped

disc.

Alternate Channel Selectivity:

75 dB

Treble Control Action (10 kHz):

±10 dB

Line Output Level (MD 1 kHz):

4 V

An MD is caught inside the MD deck and

is not ejected.

This is a failure of MD deck’s mechanism

and consult your store of purchase.

Stereo Separation (1 kHz):

35 dB

An MD cannot be played due to scratches, Replace with a non-scratched,

etc. non-warped-disc.

Frequency Response (±3 dB):

30 Hz to 15 kHz

General

Power Supply Voltage:

14.4 V DC (10.8 to 15.6 V allowable),

negative ground

A CD inside the CD changer is not loaded. This is a failure of CD changer’s mecha-

nism and consult your store of purchase.

AM Tuner

Frequency Range:

530 kHz to 1710 kHz

A CD inside the CD changer cannot be

played due to scratches, etc.

Replace with a non-scratched, non-warped

disc.

Current Consumption:

Less than 15 A

Usable Sensitivity:

25 µV

A CD inside the CD changer cannot be

played because it is loaded upside-down.

Eject the disc then reload it properly.

Speaker Impedance:

4 Ω (4 Ω to 8 Ω allowable)

Weight / Source unit:

5.5 lb. (2.5 kg)

Displayed when the temperature in the MD Lower the surrounding temperature and

changer is too high and playback has been wait for a while to cool off MD changer.

stopped automatically.

CD Player

Frequency Response (±1 dB):

10 Hz to 20 kHz

Weight / Remote control unit:

1 oz. (30 g) (including battery)

ERROR 2

ERROR 3

ERROR 6

An MD inside the MD changer is not

loaded.

This is a failure of MD changer’s mecha-

nism and consult your store of purchase.

Signal to Noise Ratio (1 kHz):

100 dB

Dimensions / Source unit:

7" (Width) × 3-15/16" (Height) × 6-1/8" (Depth)

[178 (W) × 100 (H) × 155 (D) mm]

Dimensions / Remote control unit:

1-3/4" (Width) × 4-5/16" (Height) × 1-1/8" (Depth)

[44 (W) × 110 (H) × 27 (D) mm]

Dynamic Range (1 kHz):

95 dB

An MD inside the MD changer cannot be

played due to scratches, etc.

Replace with a non-scratched, non-warped

disc.

Harmonic Distortion:

0.01%

Displayed when a non-recorded MD is

loaded in the MD changer.

Load a pre-recorded MD in the MD

changer.

MD Player

Frequency Response (±2 dB):

20 Hz to 20 kHz

If an error display other than the ones described above appears, press the reset button. If the problem

persists, turn off the power and consult your store of purchase.

Signal to Noise Ratio (1 kHz):

90 dB

Dynamic Range (1 kHz):

85 dB

Harmonic Distortion:

0.01%

Notes:

• Specifications comply with EIA Standards.

• US and foreign patents licensed from Dolby Laboratories Licensing Corporation.

• Specifications and design are subject to change without notice for further improvement.

DMX5 5 5 5 z

Download from Www.Somanuals.com. All Manuals Search And Download.

280 7323 00

Acer Computer Monitor PD725P User Manual
ADTRAN Network Router ACT 1900 User Manual
Alamo Lawn Mower SHD62 User Manual
Alliance Laundry Systems Clothes Dryer 70269701R4 User Manual
AltiGen comm Network Card Advanced Call RouterTM User Manual
Amana Oven ACF4255A User Manual
Apple Network Router U10C012 User Manual
Avenview Stereo System DVI C5 R User Manual
Axis Communications Security Camera P3214 V User Manual
Banner Stud Sensor P4 GEO 13 User Manual