®
A7V-M
JumperFree™ PC133/VC133
200MHz FSB AGP 4X
Socket A Motherboard
USER’S MANUAL
ASUS CONTACT INFORMATION
ASUSTeK COMPUTER INC. (Asia-Pacific)
Marketing
Address:
Telephone:
Fax:
150 Li-Te Road, Peitou, Taipei, Taiwan 112
+886-2-2894-3447
+886-2-2894-3449
Email:
Technical Support
MB/Others (Tel): +886-2-2890-7121 (English)
Notebook (Tel):
+886-2-2890-7122 (English)
Desktop/Server (Tel):+886-2-2890-7123 (English)
Fax:
+886-2-2893-7775
www.asus.com.tw
Email:
WWW:
FTP:
ftp.asus.com.tw/pub/ASUS
ASUS COMPUTER INTERNATIONAL (America)
Marketing
Address:
6737 Mowry Avenue, Mowry Business Center, Building 2
Newark, CA 94560, USA
Fax:
Email:
+1-510-608-4555
Technical Support
Fax:
+1-510-608-4555
www.asus.com
ftp.asus.com/Pub/ASUS
Email:
WWW:
FTP:
ASUS COMPUTER GmbH (Europe)
Marketing
Address:
Fax:
Harkortstr. 25, 40880 Ratingen, BRD, Germany
+49-2102-442066
Email:
[email protected] (for marketing requests only)
Technical Support
Hotline:
Fax:
Support (Email):
MB/Others: +49-2102-9599-0 Notebook: +49-2102-9599-10
+49-2102-9599-11
www.asuscom.de/de/support (for online support)
WWW:
FTP:
www.asuscom.de
ftp.asuscom.de/pub/ASUSCOM
ASUS A7V-M User’s Manual
3
CONTENTS
1. INTRODUCTION
7
1.1 How This Manual Is Organized ................................................. 7
1.2 Item Checklist ............................................................................ 7
2. FEATURES
8
2.1 The ASUS A7V-M ..................................................................... 8
2.1.1 Specifications .................................................................. 8
2.1.2 Special Features ............................................................ 10
2.1.3 Performance Features.................................................... 10
2.1.4 Intelligence .................................................................... 11
2.2 Motherboard Components ....................................................... 12
2.2.1 Component Locations ................................................... 13
3. HARDWARE SETUP
14
3.1 Motherboard Layout ................................................................ 14
3.2 Layout Contents ....................................................................... 15
3.3 Hardware Setup Procedure ...................................................... 17
3.4 Motherboard Settings............................................................... 17
3.5 System Memory (DIMM) ........................................................ 21
3.5.1 General DIMM Notes ................................................... 21
3.5.2 Memory Installation ...................................................... 22
3.6 Central Processing Unit (CPU) ................................................ 23
3.7 Expansion Cards ...................................................................... 24
3.7.1 Expansion Card Installation Procedure ......................... 24
3.7.2 Assigning IRQs for Expansion Cards ........................... 26
3.7.3 Accelerated Graphics Port (AGP) ................................. 27
3.8 External Connectors................................................................. 29
3.9 Starting Up the First Time ....................................................... 41
4. BIOS SETUP
43
4.1 Managing and Updating Your BIOS ........................................ 43
4.1.1 Upon First Use of the Computer System ...................... 43
4.1.2 Updating BIOS Procedures ........................................... 44
4.2 BIOS Setup Program ............................................................... 47
4.2.1 BIOS Menu Bar ............................................................ 48
4.2.2 Legend Bar .................................................................... 48
4.3 Main Menu............................................................................... 50
4.3.1 Primary & Secondary Master/Slave.............................. 51
4.3.2 Keyboard Features ........................................................ 54
4
ASUS A7V-M User’s Manual
CONTENTS
4.4 Advanced Menu ....................................................................... 56
4.4.1 Chip Configuration ....................................................... 59
4.4.2 I/O Device Configuration ............................................. 62
4.4.3 PCI Configuration ......................................................... 65
4.4.4 Shadow Configuration .................................................. 69
4.5 Power Menu ............................................................................. 70
4.5.1 Power Up Control ......................................................... 72
4.5.2 Hardware Monitor......................................................... 74
4.6 Boot Menu ............................................................................... 75
4.7 Exit Menu ................................................................................ 77
5. SOFTWARE SETUP
79
5.1 Install Operating System.......................................................... 79
5.2 Start Windows.......................................................................... 79
5.3 A7V-M Series Motherboard Support CD ................................ 80
5.4 VIA 4 in 1 drivers .................................................................... 81
5.5 Audio Driver ............................................................................ 82
5.6 Realtek RTL8139C PCI Fast Ethernet NIC Driver ................. 83
5.7 ASUS PC Probe Vx.xx ............................................................ 84
5.8 ASUS Update Vx.xx ................................................................ 85
5.9 YAMAHA Soft Synthesizer S-YXG50 ................................... 86
5.10 PC-Cillin 98 Vx.xx .................................................................. 87
5.11 ADOBE Acrobat Reader Vx.xx ............................................... 88
5.12 Cyberlink Video and Audio Applications ................................ 89
5.13 Uninstalling Programs ............................................................. 90
6. SOFTWARE REFERENCE
93
6.1 ASUS PC Probe ....................................................................... 93
6.2 CyberLink PowerPlayer SE ..................................................... 98
6.3 CyberLink PowerDVD ............................................................ 98
6.4 CyberLink VideoLive Mail .................................................... 100
7. APPENDIX
103
7.1 PCI-L101 Fast Ethernet Card ................................................ 103
7.2 Glossary ................................................................................. 105
ASUS A7V-M User’s Manual
5
FCC & DOC COMPLIANCE
Federal Communications Commission Statement
This device complies with FCC Rules Part 15. Operation is subject to the following
two conditions:
•
•
This device may not cause harmful interference, and
This device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with manufacturer's instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
•
•
•
Re-orient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
WARNING! Any changes or modifications to this product not expressly ap-
proved by the manufacturer could void any assurances of safety or performance
and could result in violation of Part 15 of the FCC Rules.
Reprinted from the Code of Federal Regulations #47, part 15.193, 1993. Washington DC: Office of the
Federal Register, National Archives and Records Administration, U.S. Government Printing Office.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions
from digital apparatus set out in the Radio Interference Regulations of the Canadian
Department of Communications.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
6
ASUS A7V-M User’s Manual
1. INTRODUCTION
1.1 How This Manual Is Organized
This manual is divided into the following sections:
1. INTRODUCTION
2. FEATURES
3. HARDWARE SETUP
4. BIOS SETUP
Manual information and checklist
Production information and specifications
Intructions on setting up the motherboard.
Intructions on setting up the BIOS
5. SOFTWARE SETUP
6. SOFTWARE REFERENCE
7. APPENDIX
Intructions on setting up the included software
Reference material for the included software
Optional items and general reference
1.2 Item Checklist
Check that your package is complete. If you discover damaged or missing items,
contact your retailer.
Package Contents
Optional Items
(1) ASUS Motherboard
ASUS CIDB chassis intrusion detec-
tion module
(1) 40-pin 80-conductor ribbon
cable for internal UltraDMA/66
or UltraDMA/33 devices
ASUS IrDA-compliant infrared
module
ASUS PCI-L101 Wake-On-LAN 10/
100 Ethernet Card
(1) Ribbon cable for one 5.25” and
two 3.5” floppy disk drives
(1) ASUS 2-port USB Connector Set
(1) Bag of spare jumper caps
(1) ASUS Support CD with drivers
and utilities
(1) This Motherboard User’s
Manual
ASUS A7V-M User’s Manual
7
2. FEATURES
2.1 The ASUS A7V-M
The ASUS A7V-M motherboard is carefully designed for the demanding PC user
who wants advanced features processed by the fastest processors.
2.1.1 Specifications
•
AMDAthlon™/Duron™ Processor Support: Supports SocketA-basedAMD
Athlon™/Duron™ processors.
•
North Bridge System Chipset: Features the VIAVT8363 (VIAApollo KT133)
system controller with support for a 200MHz Front Side Bus (FSB); up to 1.5GB
of PC133/PC100 SDRAM / VC 133 Virtual Channel Memory (VCM) SDRAM;
complies with AGP 2.0 specifications for 4X, 2X, and 1X AGP modes; and PCI
2.2. bus interface with support for 5 PCI masters. It is optimized to deliver en-
hanced AMD Athlon™/Duron™ processor system performance.
•
•
“Super South” South Bridge System PCIset: VIA VT82C686A PCIset with
PCI Super-I/O Integrated Peripheral Controller (PSIPC) with support for
UltraDMA/66, which allows burst mode data transfer rates of up to 66.6MB/sec;
AC97 audio; USB controller with root hub and four function ports.
PC133 SDRAM /VC133 VCM Support: Equipped with two Dual Inline Memory
Module (DIMM) sockets to support Intel PC133/PC100-compliant (8, 16, 32, 64,
128, 256, or 512MB) or NEC’s VC133-compliant Virtual Channel (VC) SDRAM
up to 1GB. VC SDRAM is a new DRAM core architecture that dramatically im-
proves the memory system’s ability to service, among others, high multimedia
requirements.
•
•
Stepless Frequency Selection: Allows CPU external (FSB) frequency settings
to be set in 1MHz-increments or reduction.
JumperFree™ Mode: Allows processor settings and easy overclocking of fre-
quency and Vcore voltage all through BIOS setup when JumperFree™ mode is
enabled. Easy-to-use DIP switches instead of jumpers are included to allow
manual adjustment of the processor’s external frequency.
•
•
AGP Slot: Supports AGP cards for high performance, component level inter-
connection targeted at 3D graphical applications supporting 133MHz 4X mode.
UltraDMA/66 Support: Comes with an onboard PCI Bus Master IDE control-
ler with two connectors that support four ATA66/33 devices on two channels.
Supports UltraDMA/66, UltraDMA/33, PIO Modes 3 & 4 and Bus Master IDE
DMA Mode 2, and Enhanced IDE devices, such as DVD-ROM, CD-ROM, CD-
R/RW, LS-120, and Tape Backup drives.
•
Wake-On-LAN Connector: Supports Wake-On-LAN activity through an op-
tional onboard Realtek Fast Ethernet Controller or an optional ASUS PCI-L101
10/100 Fast Ethernet PCI card (see 7. Appendix).
ASUS A7V-M User’s Manual
8
2. FEATURES
Wake-On-Ring Connector: Supports Wake-On-Ring activity through a PCI
•
modem card that supports a WOR connector.
•
•
USB: Supports up to 4 USB ports, two on the back panel and two midboard, for
more peripheral connectivity options.
PC Health Monitoring: Provides an easy way to examine and manage system
status information, such as CPU and systerm voltages, temperatures, and fan
status through the onboard hardware ASUS ASIC and the bundled ASUS PC
Probe.
•
•
SMBus: Features the System Management Bus interface, which is used to physi-
cally transport commands and information between SMBus devices.
PCI Expansion Slots: Provides three 32-bit PCI (Rev. 2.2) expansion slots,
which can support Bus Master PCI cards, such as SCSI or LAN cards (PCI
supports up to 133MB/s maximum throughput).
•
•
Super Multi-I/O: Provides two high-speed UART compatible serial ports and
one parallel port with EPP and ECP capabilities.
Enhanced ACPI & Anti-Boot Virus Protection: Programmable BIOS (Flash
EEPROM), offering enhancedACPI for Windows 98 compatibility, built-in firm-
ware-based virus protection, and autodetection of most devices for virtually au-
tomatic setup.
•
•
Concurrent PCI: Concurrent PCI allows multiple PCI transfers from PCI mas-
ter busses to the memory and processor.
Smart BIOS: 2Mb firmware provides Vcore and CPU/SDRAM frequency ad-
justments, boot block write protection, and HD/SCSI/MO/ZIP/CD/Floppy boot
selection. Power supply is autodetected to enable/disable suspend-to-RAM.
•
•
•
Integrated Infrared (IrDA) Support: Integrated IR supports an optional re-
mote control package for wireless interfacing with external peripherals, per-
sonal gadgets, or an optional remote controller.
Desktop Management Interface (DMI): Supports DMI through BIOS, which
allows hardware to communicate within a standard protocol creating a higher
level of compatibility. (Requires DMI-enabled components.)
Color-coded Connectors:To enhance user accessibility to system components and
to meet PC 99 compliancy, major connectors in this motherboard are color-coded.
ASUS A7V-M User’s Manual
9
2. FEATURES
2.1.2 Special Features
•
ACPI Ready: Advanced Configuration Power Interface (ACPI) provides more
Energy Saving Features for operating systems that support OS Direct Power
Management (OSPM) functionality. With these features implemented in the OS,
PCs can be ready around the clock, yet satisfy all the energy saving standards.
To fully utilize the benefits of ACPI, an ACPI-supported OS, such as Windows
98 must be used.
•
•
Easy Installation: Incorporates BIOS that supports autodetection of hard disk
drives, PS/2 mouse, and Plug and Play devices to make the setup of hard disk
drives, expansion cards, and other devices virtually automatic.
New Compliancy: Both the BIOS and hardware levels of this motherboard meet
the stringent requirements for PC 99 certification The new PC 99 requirements
for systems and components are based on the following high-level goals: Sup-
port for Plug and Play compatibility and power management for configuring
and managing all system components, and 32-bit device drivers and installation
procedures for Windows95/98/NT . Color-coded connectors and descriptive icons
make identification easy as required by PC 99.
•
Symbios SCSI BIOS: Supports optional ASUS SCSI controller cards through
the onboard SYMBIOS firmware.
2.1.3 Performance Features
•
Concurrent PCI: Concurrent PCI allows multiple PCI transfers from PCI mas-
ter busses to the memory and processor.
•
High-Speed Data Transfer Interface: IDE transfers using UltraDMA/33 Bus
Master IDE can handle rates up to 33MB/s. This motherboard with its chipset
and support for UltraDMA/66 doubles the data transfer rate to 66.6MB/s.
UltraDMA/66 is backward compatible with both DMA/33 and DMA and with
existing DMA devices and systems so there is no need to upgrade current EIDE/
IDE drives and host systems. (UltraDMA/66 requires a 40-pin 80-conductor
cable to be enabled.)
•
VCM/SDRAM Optimized Performance: This motherboard supports a new gen-
eration memory, NEC’s 64Mb Virtual Channel Memory (VCM) Synchronous Dy-
namic Random Access Memory (SDRAM), which is compatible to the industry
standard SDRAM. The VCM’s core design provides up to 50% higher SDRAM
speed at reduced power consumption of about 30%. This motherboard also supports
standard SDRAM, which increases the data transfer rate (1.064GB/s max using
PC133-compliant SDRAMs and 800MB/s max using PC100-compliant SDRAMs).
ASUS A7V-M User’s Manual
10
2. FEATURES
2.1.4 Intelligence
•
Auto Fan Off: The system fans will power off automatically even in sleep
mode. This function reduces both energy consumption and system noise, and is
an important feature in implementing silent PC systems.
•
Dual Function Power Button: Pushing the power button for less than 4 sec-
onds when the system is in the working state places the system into one of two
states: sleep mode or soft-off mode, depending on the BIOS or OS setting (see
PWR Button < 4 Secs in 4.5 Power Menu). When the power button is pressed
for more than 4 seconds, the system enters the soft-off mode regardless of the
BIOS setting.
•
•
•
Fan Status Monitoring and Alarm: To prevent system overheat and system
damage, the CPU, power supply, and system fans can be monitored for RPM
and failure. All fans are set for its normal RPM range and alarm thresholds.
Remote Ring On (requires modem): This allows a computer to be turned on
remotely through an internal or external modem. With this benefit on-hand, users
can access vital information from their computers from anywhere in the world!
System Resources Alert: Today’s operating systems such as Windows 95/98/
NT and OS/2, require much more memory and hard drive space to present enor-
mous user interfaces and run large applications. The system resource monitor
will warn the user before the system resources are used up to prevent possible
application crashes. Suggestions will give the user information on managing
their limited resources more efficiently.
•
•
Temperature Monitoring and Alert: CPU temperature is monitored by the
ASUS ASIC to prevent system overheat and system damage.
Voltage Monitoring and Alert: System voltage levels are monitored to ensure
stable voltage to critical motherboard components. Voltage specifications are
more critical for future processors, so monitoring is necessary to ensure proper
system configuration and management.
•
Chassis Intrusion Detection: Supports chassis-intrusion monitoring through
the ASUS ASIC. A chassis intrusion event is kept in memory on battery power
for more protection.
ASUS A7V-M User’s Manual
11
2. FEATURES
2.2 Motherboard Components
See opposite page for locations.
Location
Processor Support Socket A for Socket AAMD Athlon/Duron Processors ........... 3
(NOTE: CPU thermal sensor is integrated on the motherboard,
located near the center of the CPU heat source, just below the
CPU socket)
Feature Setting DIP Switches ................................................... 7
Chipsets VIA VT8363 (VIAApollo KT133) system controller .............. 2
VIA VT82C686A PCIset......................................................... 14
2Mbit Programmable Flash EEPROM ..................................... 9
Main Memory Maximum 1GB support
2 DIMM Sockets ...................................................................... 4
VC133/PC133 memory support
Expansion Slots 3PCI Slots ............................................................................... 18
1 Accelerated Graphics Port (AGP) Slot ................................ 20
System I/O 1 Floppy Disk Driver Connector .............................................. 8
2 IDE Connectors (UltraDMA/66 Support) ............................. 6
1 Parallel Port Connector ............................................. (Top) 24
1 Serial COM1 Port Connector .............................. (Bottom) 25
1 Serial COM2 Port Connector .............................. (Bottom) 23
USB Connectors (Port 0 & Port 1) ........................ (Bottom) 26
USB Connectors (Port 2 & Port 3) ......................................... 13
1 PS/2 Mouse Connector .............................................. (Top) 27
1 PS/2 Keyboard Connector ................................... (Bottom) 27
Audio AC’97 V2.1 Audio Codec (optional) ..................................... 19
Creative Audio Controller (optional) ..................................... 17
1 Game/MIDI Connector (on audio model only) ......... (Top) 22
1 Line Out Connector (on audio model only) ........ (Bottom) 22
1 Line In Connector (on audio model only) ........... (Bottom) 22
1 Microphone Connector (on audio model only) ... (Bottom) 22
Network Features Realtek RTL 8139C Fast Ethernet Controller (optional) ....... 21
1 LAN (RJ45) Connector (optional) ........................... (Top) 26
Wake-On-LAN Connector...................................................... 16
Wake-On-Ring Connector ...................................................... 12
Hardware Monitoring System Voltage Monitoring (integrated in ASUS ASIC) ....... 10
3 Fan Power and Speed Monitoring Connectors
Power ATX Power Supply Connector ................................................. 1
Others Onboard LED ........................................................................... 5
SMBus Connector .................................................................. 11
Buzzer (optional) .................................................................... 15
Form Factor Micro ATX
ASUS A7V-M User’s Manual
12
2. FEATURES
2.2.1 Component Locations
1
2
3
4
5 6 7 8
27
26
25
24
23
22
21
20
19
18
17
16
15
14 13 12 11 10 9
-
ASUS A7V-M User’s Manual
13
3. HARDWARE SETUP
3.1 Motherboard Layout
PS/2
T: Mouse
B: Keyboard
CPU_FAN
Top:
USB
T: USB1
B: USB2
RJ-45
Socket A
SW1
COM1
PS_FAN
VIA
COM2
VT8363
Line
Out
Chipset
Line
In
CR2032 3V
Lithium Cell
CMOS Power
CD
Realtek
Fast
Ethernet
CHASS_FAN
Mic
In
0
1
2
3
Accelerated Graphics Port (AGP)
AUX
VIDEO
CLRTC
JEN
PCI Slot 1
Audio
Codec
VIA
HPHONE
VT82C686A
Chipset
PCI Slot 2
MODEM
A7V-M
USB2
WOLCON
IR
PCI Slot 3
Buzzer
WOR
SMB
Audio
Controller
IDELED
HPANEL
Grayed components are optional at the time of purchase.
ASUS A7V-M User’s Manual
14
3. HARDWARE SETUP
3.2 Layout Contents
Motherboard Settings
1) JEN
p. 18 JumperFree Mode (JumperFree/Jumper Mode)
p. 20 CPU External Frequency Setting
2) SW1 1–4
Expansion Slots/Sockets
1) System Memory
p.21 System Memory Support
2) DIMM1/2
p.22 DIMM Memory Module Support
3) Socket 462 (Socket A) p.23 CPU Support
4) PCI1/2/3
5) AGP
p.26 32-bit PCI Bus Expansion Slots
p.27 Accelerated Graphics Port (AGP)
Connectors
1) PS2KBMS
p.29 PS/2 Mouse Port Connector (6 pin-female)
p.29 PS/2 Keyboard Port Connector (6-pin female)
p.30 Universal Serial Bus Connectors 0 & 1 (Two 4-pin female)
p.30 Serial Port Connector (9-pin male)
2) PS2KBMS
3) USB
4) COM1/COM2
5) PRINTER
6) GAME_AUDIO
7) GAME_AUDIO
8) RJ45
p.30 Parallel Port Connector (25-pin female)
p.31 Game/MIDI Connector (15-pin female) (optional)
p.31 Audio Port Connectors (Three 1/8” female) (optional)
p.31 Fast-Ethernet Port Connector (RJ45) (optional)
p.32 IDE Connectors (Two 40-1 pins)
9) PRIMARY IDE
SECONDARY IDE
10) FLOPPY
11) CHASS
12) IR
p.32 Floppy Disk Drive Port Connector (34 pins)
p.33 Chassis Intrusion Lead (4-1 pins)
p.33 Infrared Module Connector (5 pins)
p.34 Wake-On-LAN Connector (3 pins)
p.34 Wake-On-Ring Connector (2 pins)
13) WOL_CON
14) WOR
15) CPU_, PS_, CHASS_FAN p.35 Chassis, Power Supply, CPU Fan Connectors (3 pins)
16) CD_IN, AUX, VIDEO, p.36 Internal Audio Connectors (4 4-pin)
MODEM
17) HPHONE
p.36 Headphone True-Level Out Header (3 pins)
p.37 USB Header (10-1 pins)
18) USB2
19) SMB
p.37 SMBus Connector (5-1 pins)
20) ATXPWR
p.38 ATX Power Supply Connector (20 pins)
p.39 IDE Activity LED (2 pins)
21) IDELED
22) SPEAKER (PANEL)
23) PWR.LED (PANEL)
24) RESET (PANEL)
25) PWR.SW (PANEL)
26) SMI (PANEL)
p.40 System Warning Speaker Connector (4 pins)
p.40 System Power LED Lead (3 pins)
p.40 Reset Switch Lead (2 pins)
p.40 ATX / Soft-Off Switch Lead (2 pins)
p.40 System Management Interrupt Lead (2 pins)
ASUS A7V-M User’s Manual
15
3. HARDWARE SETUP
(This page was intentionally left blank.)
ASUS A7V-M User’s Manual
16
3. HARDWARE SETUP
3.3 Hardware Setup Procedure
Before using your computer, you must complete the following steps:
1. Check Motherboard Settings
2. Install Memory Modules
3. Install the Central Processing Unit (CPU)
4. Install Expansion Cards
5. Connect Ribbon Cables, Panel Wires, and Power Supply
6. Setup the BIOS Software
3.4 Motherboard Settings
This section explains in detail how to change your motherboard’s function settings
through the use of switches and/or jumpers.
WARNING! Computer motherboards and expansion cards contain very delicate
Integrated Circuit (IC) chips. To protect them against damage from static electric-
ity, you should follow some precautions whenever you work on your computer.
1. Unplug your computer when working on the inside.
2. Use a grounded wrist strap before handling computer components. If you do
not have one, touch both of your hands to a safely grounded object or to a
metal object, such as the power supply case.
3. Hold components by the edges and try not to touch the IC chips, leads or
connectors, or other components.
4. Place components on a grounded antistatic pad or on the bag that came with
the component whenever the components are separated from the system.
5. Ensure that the ATX power supply is switched off before you plug in or
remove the ATX power connector on the motherboard.
WARNING! Make sure that you unplug your power supply when adding or re-
moving system components. Failure to do so may cause severe damage to your
motherboard, peripherals, and/or components. The onboard LED when lit acts as
a reminder that the system is in suspend or soft-off mode and not powered OFF.
LED
ON
OFF
Standby
Power
Powered
Off
A7V-M
A7V-M Onboard LED
ASUS A7V-M User’s Manual
17
3. HARDWARE SETUP
Motherboard Features Settings (DIP Switches - SW1)
The motherboard’s onboard functions are adjusted through the DIP switches. The
white block represents the switch’s position. The example below shows all the
switches in the OFF position.
SW1
1. Frequency Selection
A7V-M
2. Frequency Selection
3. Frequency Selection
4. Frequency Selection
A7V-M DIP Switches
1) Jumper Setting (JEN)
This jumper allows you to enable or disable the JumperFree™ mode. The
JumperFree™ mode allows processor settings to be made through the BIOS
setup (see 4.4 Advanced Menu).
Setting
JumperFree™
Jumper Mode
JEN
[2-3] (default)
[1-2]
SW1
In JumperFree™ Mode,
dip switches (SW1)
must bet set as shown
(ON: 1, 2, 4; OFF: 3)
JEN
A7V-M
1 2
3
2
Jumper Mode
JumperFree™
(Default)
A7V-M Jumper Setting
ASUS A7V-M User’s Manual
18
3. HARDWARE SETUP
(This page was intentionally left blank.)
ASUS A7V-M User’s Manual
19
3. HARDWARE SETUP
2) CPU External Frequency Setting (SW1 Switches 1–4)
This option tells the clock generator what frequency to send to the CPU, SDRAM,
and the chipset. This allows the selection of the CPU’s External frequency. The
CPU External Frequency multiplied by the Frequency Multiple equals the CPU’s
Internal frequency (the advertised CPU speed).
IMPORTANT:
1. To use this feature, JEN [see 1) JumperFree™ Mode (JEN) in 3. HARD-
WARE SETUP] must be set to Jumper mode or [1-2].
2. In JumperFree mode, SW1 Switches 1,2 and 4 must be set to ON and SW1
Switch 3 to OFF (see 1) Jumper Setting earlier in this section).
3. When JumperFree mode is enabled, use BIOS setup in place of these switches
(set Operating Frequency Setting to User Define under 4.4Advanced Menu
in BIOS Setup so you can set the CPU Frequency).
CPU 100.00MHz
PCI 33.33MHz
103.00MHz
34.33MHz
A7V-M
CPU 105.00MHz
PCI 35.00MHz
110.00MHz
36.67MHz
A7V-M CPU
External Frequency Selection
NOTE: The motherboard supports PC100 / PC133 DIMMs or VC SDRAMs
for system memory. Registered DIMMs are not supported [see 3.5 System
Memory (DIMM)].
External Frequency Table
CPU
PCI
Frequency Selection Switches
(MHz) (MHz)
1
2
3
4
100.00 33.33
103.00 34.33
105.00 35.00
110.00 36.67
[ON]
[OFF]
[ON]
[ON]
[ON]
[ON]
[OFF]
[OFF]
[OFF]
[OFF]
[OFF]
[ON]
[ON]
[ON]
[ON]
[OFF]
NOTE: For updated processor settings, visit theASUS web site (see ASUS CON-
TACT INFORMATION).
WARNING! Frequencies other than the recommended CPU bus frequencies are
not guaranteed to be stable. Overclocking your processor is not recommended. It
may result in a slower speed and premature wearing of the processor.
ASUS A7V-M User’s Manual
20
3. HARDWARE SETUP
3.5 System Memory (DIMM)
This motherboard uses only Dual Inline Memory Modules (DIMMs). Two sockets
are available for 3.3Volt (power level) unbuffered Synchronous Dynamic Random
Access Memory (SDRAM) of 8, 16, 32, 64, 128, 256, or 512MB to form a memory
size between 8MB to 1GB. One side (with memory chips) of the DIMM takes up one
row on the motherboard. This motherboard also supports NEC’s Virtual Channel
(VC) SDRAMs.
Memory speed setup is recommended through SDRAM Configuration under “Chipset
Features Setup”.
IMPORTANT (see General DIMM Notes below for more)
•
SDRAMs used must be compatible with current PC133 SDRAM specifica-
tion.
•
DO NOT attempt to mix PC133 SDRAMs with VCM SDRAMs.
Install memory in any combination as follows:
DIMM Location
168-pin DIMM
Total Memory
Socket 1 (Rows 0&1)
Socket 2 (Rows 2&3)
SDRAM 8, 16, 32, 64, 128, 256, 512MB x1
SDRAM 8, 16, 32, 64, 128, 256, 512MB x1
Total System Memory (Max 1024MB) =
3.5.1 General DIMM Notes
•
•
DIMMs that have more than 18 chips are not supported on this motherboard.
For the system CPU bus to operate at 100MHz/133MHz, use only PC100-/PC133-
compliant DIMMs.
•
ASUS motherboards support SPD (Serial Presence Detect) DIMMs. This is the
memory of choice for best performance vs. stability.
•
•
BIOS shows SDRAM memory on bootup screen.
Single-sided DIMMs come in 16, 32, 64,128, 256MB; double-sided come in 32, 64,
128, 256, 512MB.
WARNING! Be sure that the DIMM you use can handle the specified SDRAM
MHz or else bootup will not be possible.
ASUS A7V-M User’s Manual
21
3. HARDWARE SETUP
3.5.2 Memory Installation
WARNING! Make sure that you unplug your power supply when adding or
removing memory modules or other system components. Failure to do so may
cause severe damage to both your motherboard and expansion cards (see 3.3
Hardware Setup Procedure for more information).
Insert the module(s) as shown. Because the number of pins are different on either
side of the breaks, the module will only fit in the orientation shown. DRAM SIMM
modules have the same pin contacts on both sides. SDRAM DIMMs have different
pin contacts on each side and therefore have a higher pin density.
20 Pins
60 Pins
88 Pins
A7V-M
A7V-M 168-Pin DIMM Sockets
The DIMMs must be 3.3Volt unbuffered SDRAMs. To determine the DIMM type,
check the notches on the DIMMs (see figure below).
168-Pin DIMM Notch Key Definitions (3.3V)
Voltage Key Position
Reserved
DRAM Key Position
RFU
Unbuffered
Buffered
5.0V
3.3V
The notches on the DIMM will shift between left, center, or right to identify the type
and also to prevent the wrong type from being inserted into the DIMM slot on the
motherboard. You must tell your retailer the correct DIMM type before purchasing.
This motherboard supports four clock signals per DIMM.
ASUS A7V-M User’s Manual
22
3. HARDWARE SETUP
3.6 Central Processing Unit (CPU)
The motherboard provides a Socket 462 or Socket A for CPU installation. The CPU
that came with the motherboard should have a fan and heatsink attached to it to
prevent overheating. If this is not the case, then purchase and install a set before you
turn on your system.
WARNING! Make sure that the heatsink is mounted tightly against the processor.
Make sure also that there is sufficient air circulation across the processor’s heat-
sink by regularly checking that your CPU fan is working. Without sufficient cir-
culation, the processor could overheat and damage both the processor and the
motherboard. You may install an auxiliary fan, if necessary. A CPU thermal sen-
sor is integrated on the motherboard, located near the center of the CPU heat
source, just below the CPU socket, to help in monitoring the CPU temperature.
To install a CPU, first turn off your system and remove its cover. Locate the Socket
462 and open it by first pulling the lever sideways away from the socket then up-
ward to a 90-degree angle. Insert the CPU with the correct orientation as shown. The
notched corner should be orientated toward the blank space on the socket nearest the
lever. Because the CPU has a corner pin for two of the four corners, the CPU will
only fit in the orientation as shown. The picture is for reference only; you should
have a CPU fan and heatsink that covers the face of the CPU. With the added weight
of the CPU fan and heatsink, no force is required to insert the CPU. Once com-
pletely inserted, close the socket’s lever while holding down the CPU.
NOTE: Do not forget to set the correct Bus Frequency and Multiple (frequency mul-
tiple setting is available only on unlocked processors) for your processor or else boot-
up may not be possible. SocketA processors require a socket mounted thermal resistor.
CAUTION! • Be careful not to scrape the motherboard when mounting/unmounting a
clamp-styleprocessorfanorelsedamagemayoccurtothemotherboard.
• When mounting a heatsink onto your CPU, make sure that the
CPU capacitors (see encircled areas below) do not touch the
heatsink; otherwise, your CPU will be damaged! See your
heatsink/CPU documentation for details.
BLANK
LEVER
LOCK
NOTCH
AMD™ Athlon
A7V-M
A7V-M Socket A
ASUS A7V-M User’s Manual
23
3. HARDWARE SETUP
(This page was intentionally left blank.)
24
ASUS A7V-M User’s Manual
3. HARDWARE SETUP
3.7 Expansion Cards
WARNING! Unplug your power supply when adding or removing expansion
cards or other system components. Failure to do so may cause severe damage to
both your motherboard and expansion cards.
3.7.1 Expansion Card Installation Procedure
1. Read the documentation for your expansion card and make any necessary hard-
ware or software settings for your expansion card, such as jumpers.
2. Remove your computer system’s cover and the bracket plate on the slot you
intend to use. Keep the bracket for possible future use.
3. Carefully align the card’s connectors and press firmly.
4. Secure the card on the slot with the screw you removed above.
5. Replace the computer system’s cover.
6. Set up the BIOS if necessary
(such as IRQ XX Reserved for Legacy Device: Yes in 4.4.3 PCI Configuration)
7. Install the necessary software drivers for your expansion card.
ASUS A7V-M User’s Manual
25
3. HARDWARE SETUP
3.7.2 Assigning IRQs for Expansion Cards
Some expansion cards need an IRQ to operate. Generally, an IRQ must be exclu-
sively assigned to one use. In a standard design, there are 16 IRQs available but
most of them are already in use, leaving 6 IRQs free for expansion cards. If your
motherboard has PCI audio onboard, an additional IRQ will be used. If your moth-
erboard also has MIDI enabled, another IRQ will be used, leaving 4 IRQs free.
The following table lists the default IRQ assignments for standard PC devices. Use
this table when configuring your system and for resolving IRQ conflicts.
Standard Interrupt Assignments
IRQ
0
1
Priority
Standard Function
System Timer
Keyboard Controller
1
2
2
N/A
11
12
13
14
15
3
4
5
6
7
Programmable Interrupt
Communications Port (COM2)
Communications Port (COM1)
Sound Card (sometimes LPT2)
Floppy Disk Controller
Printer Port (LPT1)
System CMOS/Real Time Clock
ACPI Mode when used
IRQ Holder for PCI Steering
IRQ Holder for PCI Steering
PS/2 Compatible Mouse Port
Numeric Data Processor
Primary IDE Channel
3*
4*
5*
6
7*
8
9*
10*
11*
12*
13
14*
15*
8
9
10
Secondary IDE Channel
*These IRQs are usually available for PCI devices.
Interrupt Request Table for this Motherboard
INT-A
shared
—
INT-B
—
shared
—
INT-C
—
—
INT-D
PCI slot 1
PCI slot 2
PCI slot 3
—
—
—
—
not shared
—
AGP slot
Onboard USB controller
Onboard audio/SMBus
shared
—
—
—
—
shared
—
—
not shared
—
IMPORTANT: If using PCI cards on shared slots, make sure that the drivers sup-
port “Share IRQ” or that the cards do not need IRQ assignments. Conflicts will
arise between the two PCI groups that will make the system unstable or cards inop-
erable.
26
ASUS A7V-M User’s Manual
3. HARDWARE SETUP
3.7.3 Accelerated Graphics Port (AGP)
This motherboard provides an Accelerated Graphics Port (AGP) slot to support AGP
graphics cards, such as an ASUS AGP-V7700 GeForce2 GTS graphics card.
CAUTION! To avoid damaging your AGP graphics card, your computer’s power
supply should be unplugged before inserting your graphics card into the slot.
A7V-M
A7V-M Accelerated Graphics Port (AGP)
ASUS A7V-M User’s Manual
27
3. HARDWARE SETUP
(This page was intentionally left blank.)
28
ASUS A7V-M User’s Manual
3. HARDWARE SETUP
3.8 External Connectors
WARNING! Some pins are used for connectors or power sources. These are
clearly distinguished from jumpers in the Motherboard Layout. Placing jumper
caps over these connector pins will cause damage to your motherboard.
IMPORTANT: Ribbon cables should always be connected with the red stripe to
Pin 1 on the connectors. Pin 1 is usually on the side closest to the power connec-
tor on hard drives and CD-ROM drives, but may be on the opposite side on
floppy disk drives. Check the connectors before installation because there may
be exceptions. IDE ribbon cable must be less than 46 cm (18 in.), with the sec-
ond drive connector no more than 15 cm (6 in.) from the first connector.
1) PS/2 Mouse Connector (Green 6-pin PS2KBMS)
The system will direct IRQ12 to the PS/2 mouse if one is detected. If one is not
detected, expansion cards can use IRQ12. See PS/2 Mouse Function Control
in 4.4 Advanced Menu.
PS/2 Mouse (6-pin Female)
2) PS/2 Keyboard Connector (Purple 6-pin PS2KBMS)
This connection is for a standard keyboard using an PS/2 plug (mini DIN). This
connector will not allow standard AT size (large DIN) keyboard plugs. You
may use a DIN to mini DIN adapter on standard AT keyboards.
PS/2 Keyboard (6-pin Female)
ASUS A7V-M User’s Manual
29
3. HARDWARE SETUP
3) Universal Serial BUS Ports 0 & 1 (Black two 4-pin USB)
Two USB ports are available for connecting USB devices. If these are not enough,
a USB header is available for two additional USB port connectors. See USB
Headers later in this section.
USB 0
Universal Serial Bus (USB) 1
4) Serial Port Connectors (Teal/Turquoise 9-pin COM1 / COM2)
Two serial ports can be used for pointing devices or other serial devices. For
setting up these ports, see Onboard Serial Port 1 in 4.4.2 I/O Device Configu-
ration for settings.
COM1
COM2
Serial Ports (9-pin Male)
5) Parallel Port Connector (Burgundy 25-pin PRINTER)
You can enable the parallel port and choose the IRQ through Onboard Parallel
Port (see 4.4.2 I/O Device Configuration).
NOTE: Serial printers must be connected to the serial port.
Parallel Port (25-pin Female)
30
ASUS A7V-M User’s Manual
3. HARDWARE SETUP
6) Game/MIDI Connector (Gold 15-pin GAME_AUDIO) (optional)
You may connect game joysticks or game pads to this connector for playing
games. Connect MIDI devices for playing or editing professional audio.
Joystick/Midi (15-pin Female)
7) Audio Port Connectors (Three 1/8” GAME_AUDIO) (optional)
Line Out (lime) can be connected to headphones or preferably powered speak-
ers. Line In (light blue) allows tape players or other audio sources to be re-
corded by your computer or played through the Line Out (lime). Mic (pink)
allows microphones to be connected for inputting voice.
Line Out Line In Mic
1/8" Stereo Audio Connectors
8) Fast-Ethernet Port Connector (RJ45) (optional)
The RJ45 connector is located on top of the USB Ports 0 & 1. The connector
allows the motherboard to conect to a Local Area Network (LAN) through a
network hub.
RJ45
ASUS A7V-M User’s Manual
31
3. HARDWARE SETUP
9) Primary (Blue) / Secondary IDE Connectors (40-1 pin IDE1/IDE2)
These connectors support the provided UltraDMA/66 IDE hard disk ribbon cable.
Connect the cable’s blue connector to the motherboard’s primary (recommended)
or secondary IDE connector, and then connect the gray connector to your
UltraDMA/66 slave device (hard disk drive) and the black connector to your
UltraDMA/66 master device. It is recommended that non-UltraDMA/66 devices
be connected to the secondary IDE connector. If you install two hard disks, you
must configure the second drive to Slave mode by setting its jumper accord-
ingly. Refer to your hard disk documentation for the jumper settings. BIOS now
supports specific device bootup (see 4.4.1 Advanced CMOS Setup). (Pin 20 is
removed to prevent inserting in the wrong orientation when using ribbon
cables with pin 20 plugged). If you have more than two UltraDMA/66 devices,
you will need to purchase another UltraDMA/66 cable.
NOTE: The hole near the blue connector on the UltraDMA/66 cable is intentional.
TIP: You may configure two hard disks to be both Masters with two ribbon
cables – one for the primary IDE connector and another for the secondary IDE
connector. You may install one operating system on an IDE drive and another on
a SCSI drive and select the boot disk through 4.4.1 Advanced CMOS Setup.
NOTE: Orient the red markings
(usually zigzag) on the IDE
ribbon cable to PIN 1.
A7V-M
PIN 1
A7V-M IDE Connectors
10) Floppy Disk Drive Connector (34-1 pin FLOPPY)
This connector supports the provided floppy drive ribbon cable. After connect-
ing the single end to the board, connect the two plugs on the other end to the
floppy drives. (Pin 5 is removed to prevent inserting in the wrong orienta-
tion when using ribbon cables with pin 5 plugged).
NOTE: Orient the red markings on
the floppy ribbon cable to PIN 1
A7V-M
PIN 1
A7V-M Floppy Disk Drive Connector
32
ASUS A7V-M User’s Manual
3. HARDWARE SETUP
11) Chassis Intrusion Lead (2 pin CHASS)
This requires an external detection mechanism such as a chassis intrusion moni-
tor/sensor or microswitch. The sensor is triggered when a high level signal is
sent to the Chassis Signal lead, which occurs when a panel switch or light detec-
tor is triggered. This function works with an optionalASUS CIDB chassis intru-
sion module (see your vendor for more information). If the chassis intrusion
lead is not used, a jumper cap must be placed over the pins to close the circuit.
CHASS
GND
Chassis Signal
1
+5VSB_MB
A7V-M
A7V-M Chassis Open Alarm Lead
12) Standard and Consumer Infrared Module Connector (5-pin IR)
This connector supports an optional wireless transmitting and receiving infrared
module. This module mounts to a small opening on system cases that support
this feature. You must also configure the setting through UART2 Use Infrared
(see 4.4.2 I/O Device Configuration) to select whether UART2 is directed for
use with COM2 or IrDA. Use the five pins as shown in Back View and connect
a ribbon cable from the module to the motherboard’s SIR connector according
to the pin definitions.
Front View
Back View
IR
1
+5V
(NC)
IRTX
GND
A7V-M
IRRX
A7V-M Infrared Module Connector
ASUS A7V-M User’s Manual
33
3. HARDWARE SETUP
13) Wake-On-LAN Connector (3-pin WOL_CON)
This connector connects to a LAN card with a Wake-On-LAN output, such as
the ASUS PCI-L101 Ethernet card (see 7. Appendix). The connector powers up
the system when a wakeup packet or signal is received through the LAN card.
IMPORTANT: This feature requires that Wake-On-LAN features are enabled
(see 4.4.3 Power Management) and that your system has an ATX power supply
with at least 720mA +5V standby power.
IMPORTANT: Requires an ATX power
supply with at least 720mA +5 volt
standby power
WOL_CON
Ground
A7V-M
PME +5 Volt Standby
A7V-M Wake-On-LAN Connector
14) Wake-On-Ring Connector (2-pin WOR)
This connector connects to internal modem cards with a Wake-On-Ring output.
The connector powers up the system when a ringup packet or signal is received
through the internal modem card. NOTE: For external modems, Wake-On-Ring
is detected through the COM port.
IMPORTANT: This feature requires that Wake-On-Ring features are enabled
(see 4.4.3 Power Management) and that your system has an ATX power supply
with at least 720mA +5V standby power.
WOR
PIXRI#
Ground
A7V-M
1
2
A7V-M Wake-On-Ring-Connector
34
ASUS A7V-M User’s Manual
3. HARDWARE SETUP
15) CPU, Power Supply, Chassis Fan Connectors
(3-pin CPU_FAN, PS_FAN, CHASS_FAN)
These connectors support cooling fans of 350mA (4.2 Watts) or less. Orientate
the fans so that the heat sink fins allow airflow to go across the onboard heat
sink(s) instead of the expansion slots. Depending on the fan manufacturer, the
wiring and plug may be different. The red wire should be positive, while the
black should be ground. Connect the fan’s plug to the board taking into consid-
eration the polarity of the connector.
NOTE: The “Rotation” signal is to be used only by a specially designed fan with
rotation signal. The Rotations per Minute (RPM) can be monitored usingASUS PC
Probe (see 6. SOFTWARE REFERENCE).
WARNING! The CPU and/or motherboard will overheat if there is no airflow
across the CPU and onboard heatsinks. Damage may occur to the motherboard
and/or the CPU fan if these pins are incorrectly used. These are not jumpers,
do not place jumper caps over these pins.
CPU_FAN
GND
+12V
PS_FAN
Rotation
Rotation
+12V
GND
CHASS_FAN
A7V-M
A7V-M 12-Volt Cooling Fan Power
ASUS A7V-M User’s Manual
35
3. HARDWARE SETUP
16) Internal Audio Connectors (4-pin CD_IN, AUX, VIDEO, MODEM)
These connectors allow you to receive stereo audio input from such sound sources
as a CD-ROM, TV tuner, or MPEG card. The MODEM connector allows the
onboard audio to interface with a voice modem card with a similar connector.
A7V-M
VIDEO In AUX In
CD
MODEM
(Green) (White) (Black)
A7V-M Internal Audio Connectors
17) Headphone True-Level Out Header (3-pin HPHONE)
This connector allows you to connect a chassis mounted headphone to the mother-
board instead of having to attach an external headphone onto theATX connectors.
1
HPHONE
A7V-M
A7V-M Headphone Connector
36
ASUS A7V-M User’s Manual
3. HARDWARE SETUP
18) USB Header (10-1 pin USB2)
If the USB port connectors on the back panel are inadequate, this USB header is
available for two additional USB port connectors. Connect the USB headers to
the 2-port USB connector set and mount the bracket to an open slot on your
chassis.
USB2
1: USB Power 6: USB Power
2: USBP2–
3: USBP2+
4: GND
7: USBP3–
8: USBP3+
9: GND
5: NC
10
6
1
A7V-M
5
A7V-M USB Port
19) SMBus Connector (5-1 pin SMB)
This connector allows you to connect SMBus (System Management Bus) de-
vices. SMBus devices communicate by means of the SMBus with an SMBus
host and/or other SMBus devices. SMBus is a specific implementation of an I2C
bus, which is a multi-device bus; that is, multiple chips can be connected to the
same bus and each one can act as a master by initiating data transfer.
SMB
1
A7V-M
A7V-M SMBus Connector
ASUS A7V-M User’s Manual
37
3. HARDWARE SETUP
20) ATX Power Supply Connector (20-pin block ATXPWR)
This connector connects to an ATX power supply. The plug from the power sup-
ply will only insert in one orientation because of the different hole sizes. Find the
proper orientation and push down firmly making sure that the pins are aligned.
IMPORTANT: Make sure that yourATX power supply can supply at least 10mA
on the +5-volt standby lead (+5VSB). You may experience difficulty in power-
ing ON your system if your power supply cannot support the load. For Wake-
On-LAN support, your ATX power supply must supply at least 720mA +5VSB.
+3.3 Volts
+3.3 Volts
Ground
+3.3 Volts
-12.0 Volts
Ground
+5.0 Volts
Ground
Power Supply On
Ground
+5.0 Volts
Ground
Ground
Ground
Power Good
+5V Standby
+12.0 Volts
-5.0 Volts
+5.0 Volts
+5.0 Volts
A7V-M
A7V-M ATX Power Connector
38
ASUS A7V-M User’s Manual
3. HARDWARE SETUP
21) IDE Activity LED (2-pin IDELED)
This connector supplies power to the cabinet’s IDE activity LED. Read and
write activity by devices connected to the Primary/Secondary IDE and Primary/
Secondary ATA100 connectors will cause the LED to light up.
IDELED
A7V-M
TIP: If the case-mounted LED does not
light, try reversing the 2-pin plug.
A7V-M IDE Activity LED
The following PANEL illustration is used for items 22–26 (next page).
*
Requires an ATX power supply.
Speaker
Keyboard Lock
Connector
Power LED
A7V-M
Reset SW
ATX Power Switch*
SMI Lead
A7V-M System Panel Connectors
ASUS A7V-M User’s Manual
39
3. HARDWARE SETUP
22) System Warning Speaker Connector (4-pin SPEAKER)
This 4-pin connector connects to the case-mounted speaker. Two sources
(LINE_OUT and SPEAKER) will allow you to hear system beeps and warn-
ings. Only SPEAKER will allow you to hear system beeps before the integrated
audio has been properly initialized.
23) System Power LED Lead (3-1 pin PWRLED)
This 3-1 pin connector connects the system power LED, which lights when the
system is powered on and blinks when it is in sleep mode.
24) Reset Switch Lead (2-pin RESET)
This 2-pin connector connects to the case-mounted reset switch for rebooting
your computer without having to turn off your power switch. This is a preferred
method of rebooting to prolong the life of the system’s power supply.
25) ATX Power Switch Lead (2-pin PWRSW)
The system power is controlled by a momentary switch connected to this lead.
Pressing the button once will switch the system between ON and SOFT OFF.
Pushing the switch while in the ON mode for more than 4 seconds will turn the
system off. The system power LED shows the status of the system’s power.
26) System Management Interrupt Lead (2-pin SMI)
This allows the user to manually place the system into a suspend mode or “Green”
mode, where system activity is decreased to save electricity and expand the life
of certain components when the system is not in use. This 2-pin connector con-
nects to the case-mounted suspend switch. If you do not have a switch for the
connector, you may use the “Turbo Switch.” SMI is activated when it detects a
short to open moment and therefore leaving it shorted will not cause any prob-
lems. This may require one or two presses depending on the position of the
switch. Wake-up can be controlled by settings in the BIOS but the keyboard will
always allow wake-up (the SMI lead cannot wake up the system).
40
ASUS A7V-M User’s Manual
3. HARDWARE SETUP
3.9 Starting Up the First Time
1. After all connections are made, close the system case cover.
2. Be sure that all switches are off (in some systems, marked with ).
3. Connect the power supply cord into the power supply located on the
back of your system case according to your system user’s manual.
4. Connect the power cord into a power outlet that is equipped with a surge
protector.
5. You may then turn on your devices in the following order:
a. Your monitor
b. External SCSI devices (starting with the last device on the chain)
c. Your system power. For ATX power supplies, you need to switch on
the power supply as well as press the ATX power switch on the front
of the case.
6. The power LED on the front panel of the system case will light. For
ATX power supplies, the system LED will light when the ATX power
switch is pressed. The LED on the monitor may light up or switch be-
tween orange and green after the system’s if it complies with “green”
standards or if it has a power standby feature. The system will then run
power-on tests. While the tests are running, the BIOS will alarm beeps
or additional messages will appear on the screen. If you do not see any-
thing within 30 seconds from the time you turn on the power, the system
may have failed a power-on test. Recheck your jumper settings and con-
nections or call your retailer for assistance.
Award BIOS Beep Codes
Beep
Meaning
One short beep when
displaying logo
No error during POST
Long beeps in an endless loop
One long beep followed by
three short beeps
No DRAM installed or detected
Video card not found or video card
memory bad
High frequency beeps when
system is working
CPU overheated
System running at a lower frequency
ASUS A7V-M User’s Manual
41
3. HARDWARE SETUP
7. During power-on, hold down <Delete> to enter BIOS setup. Follow the
instructions in 4. BIOS SETUP.
* Powering Off your computer: You must first exit or shut down your
operating system before switching off the power switch. ForATX power
supplies, you can press the ATX power switch after exiting or shutting
down your operating system. If you use Windows 9X, click the Start
button, click Shut Down, and then click Shut down the computer?
The power supply should turn off after Windows shuts down.
NOTE: The message “You can now safely turn off your computer” will
not appear when shutting down with ATX power supplies.
42
ASUS A7V-M User’s Manual
4. BIOS SETUP
4.1 Managing and Updating Your BIOS
4.1.1 Upon First Use of the Computer System
It is recommended that you save a copy of the original motherboard BIOS
along with a Flash Memory Writer utility (AFLASH.EXE) to a bootable
floppy disk in case you need to reinstall the BIOS later. AFLASH.EXE is a
Flash Memory Writer utility that updates the BIOS by uploading a new
BIOS file to the programmable flash ROM on the motherboard. This file
works only in DOS mode. To determine the BIOS version of your mother-
board, check the last four numbers of the code displayed on the upper left-
hand corner of your screen during bootup. Larger numbers represent a newer
BIOS file.
1. Type FORMAT A:/S at the DOS prompt to create a bootable system
floppy disk. DO NOT copy AUTOEXEC.BAT & CONFIG.SYS to the
disk.
2. Type COPYD:\AFLASH\AFLASH.EXEA:\ (assuming D is your CD-
ROM drive) to copy AFLASH.EXE to the just created boot disk.
NOTE: AFLASH works only in DOS mode. It will not work with DOS
prompt in Windows and will not work with certain memory drivers that
may be loaded when you boot from your hard drive. It is recommended
that you reboot using a floppy.
3. Reboot your computer from the floppy disk. NOTE: BIOS setup must
specify “Floppy” as the first item in the boot sequence.
4. In DOS mode, type A:\AFLASH <Enter> to run AFLASH.
IMPORTANT! If “unknown” is displayed after Flash Memory:, the memory
chip is either not programmable or is not supported by theACPI BIOS and there-
fore, cannot be programmed by the Flash Memory Writer utility.
ASUS A7V-M User’s Manual
43
4. BIOS SETUP
5. Select 1. Save Current BIOS to File from the Main menu and press
<Enter>. The Save Current BIOS To File screen appears.
6. Type a filename and the path, for example, A:\XXX-XX.XXX and then
press <Enter>.
4.1.2 Updating BIOS Procedures
WARNING! Only update your BIOS if you have problems with your mother-
board and you know that the new BIOS revision will solve your problems. Care-
less updating can result in your motherboard having more problems!
1. Download an updated ASUS BIOS file from the Internet (WWW or
FTP) (see ASUS CONTACT INFORMATION on page 3 for details)
and save to the disk you created earlier.
2. Boot from the disk you created earlier.
3. At the “A:\” prompt, type AFLASH and then press <Enter>.
4. At the Main Menu, type 2 and then press <Enter>. The Update BIOS
Including Boot Block and ESCD screen appears.
5. Type the filename of your new BIOS and the path, for example, A:\XXX-
XX.XXX, and then press <Enter>.
NOTE: To cancel this operation, press <Enter>.
44
ASUS A7V-M User’s Manual
4. BIOS SETUP
6. When prompted to confirm the BIOS update, press Y to start the update.
7. The utility starts to program the new BIOS information into the flash
ROM. The boot block will be updated automatically only when neces-
sary. This will minimize the chance that a failed update will prevent
your system from booting up. When the programming is finished, Flashed
Successfully will be displayed.
8. Follow the onscreen instructions to continue.
WARNING! If you encounter problems while updating the new BIOS, DO NOT
turn off your system since this might prevent your system from booting up. Just
repeat the process, and if the problem still persists, update the original BIOS file
you saved to disk above. If the Flash Memory Writer utility was not able to
successfully update a complete BIOS file, your system may not be able to boot
up. If this happens, your system will need servicing.
ASUS A7V-M User’s Manual
45
4. BIOS SETUP
(This page was intentionally left blank.)
46
ASUS A7V-M User’s Manual
4. BIOS SETUP
4.2 BIOS Setup Program
This motherboard supports a programmable EEPROM that can be updated using
the provided utility as described in 4.1 Managing and Updating Your BIOS.
The utility is used if you are installing a motherboard, reconfiguring your system,
or prompted to “Run Setup”. This section describes how to configure your system
using this utility.
Even if you are not prompted to use the Setup program, at some time in the future
you may want to change the configuration of your computer. For example, you
may want to enable the Security Password Feature or make changes to the power
management settings. It will then be necessary to reconfigure your system using
the BIOS Setup program so that the computer can recognize these changes and
record them in the CMOS RAM of the EEPROM.
The EEPROM on the motherboard stores the Setup utility. When you start up the
computer, the system provides you with the opportunity to run this program. This
appears during the Power-On Self Test (POST). Press <Delete> to call up the Setup
utility. If you are a little bit late in pressing the mentioned key, POST will continue
with its test routines, thus preventing you from calling up Setup. If you still need to
call Setup, restart the system by pressing <Ctrl> + <Alt> + <Delete>, or by press-
ing the Reset button on the system chassis. You can also restart by turning the
system off and then back on again. But do so only if the first two methods fail.
The Setup program has been designed to make it as easy to use as possible. It is a
menu-driven program, which means you can scroll through the various sub-menus
and make your selections among the predetermined choices.
To access the BIOS Setup program, press the <Delete> key after
the computer has run through its POST.
NOTE: Because the BIOS software is constantly being updated, the following
BIOS screens and descriptions are for reference purposes only and may not re-
flect your BIOS screens exactly.
ASUS A7V-M User’s Manual
47
4. BIOS SETUP
4.2.1 BIOS Menu Bar
The top of the screen has a menu bar with the following selections:
MAIN Use this menu to make changes to the basic system configuration.
ADVANCED Use this menu to enable and make changes to the advanced
features.
POWER
BOOT
EXIT
Use this menu to configure and enable Power Management
features.
Use this menu to configure the default system device used to lo-
cate and load the Operating System.
Use this menu to exit the current menu or specify how to exit the
Setup program.
To access the menu bar items, press the right or left arrow key on the keyboard
until the desired item is highlighted.
4.2.2 Legend Bar
At the bottom of the Setup screen you will notice a legend bar. The keys in the
legend bar allow you to navigate through the various setup menus. The following
table lists the keys found in the legend bar with their corresponding alternates and
functions.
Navigation Key(s)
<F1> or <Alt + H>
Function Description
Displays the General Help screen from anywhere in the BIOS
Setup
<Esc>
Jumps to the Exit menu or returns to the main menu from a sub-
menu
← or → (keypad arrow) Selects the menu item to the left or right
↑ or ↓ (keypad arrow)
Moves the highlight up or down between fields
- (minus key)
Scrolls backward through the values for the highlighted field
+ (plus key) or spacebar Scrolls forward through the values for the highlighted field
<Enter>
Brings up a selection menu for the highlighted field
Moves the cursor to the first field
<Home> or <PgUp>
<End> or <PgDn>
Moves the cursor to the last field
<F5>
Resets the current screen to its Setup Defaults
Saves changes and exits Setup
<F10>
48
ASUS A7V-M User’s Manual
4. BIOS SETUP
General Help
In addition to the Item Specific Help window, the BIOS setup program also pro-
vides a General Help screen. This screen can be called up from any menu by sim-
ply pressing <F1> or the <Alt> + <H> combination. The General Help screen lists
the legend keys with their corresponding alternates and functions.
Saving Changes and Exiting the Setup Program
See 4.7 Exit Menu for detailed information on saving changes and exiting the
setup program.
Scroll Bar
When a scroll bar appears to the right of a help window, it indicates that there is
more information to be displayed that will not fit in the window. Use <PgUp> and
<PgDn> or the up and down arrow keys to scroll through the entire help docu-
ment. Press <Home> to display the first page, press <End> to go to the last page.
To exit the help window, press <Enter> or <Esc>.
Sub-Menu
Note that a right pointer symbol (as shown in the left view)
appears to the left of certain fields. This pointer indicates that
a sub-menu can be launched from this field. A sub-menu con-
tains additional options for a field parameter. To call up a sub-
menu, simply move the highlight to the field and press <En-
ter>. The sub-menu will then immediately appear. Use the
legend keys to enter values and move from field to field within
a sub-menu just as you would within a menu. Use the <Esc>
key to return to the main menu.
Take some time to familiarize yourself with each of the legend keys and their
corresponding functions. Practice navigating through the various menus and sub-
menus. If you accidentally make unwanted changes to any of the fields, use the set
default hot key <F5>. While moving around through the Setup program, note that
explanations appear in the Item Specific Help window located to the right of each
menu. This window displays the help text for the currently highlighted field.
NOTE: The item heading in square brackets represents the default setting for
that field.
ASUS A7V-M User’s Manual
49
4. BIOS SETUP
4.3 Main Menu
When the Setup program is accessed, the following screen appears:
System Time [XX:XX:XX]
Sets your system to the time that you specify (usually the current time).
The format is hour, minute, second. Valid values for hour, minute and sec-
ond are Hour: (00 to 23), Minute: (00 to 59), Second: (00 to 59). Use the
<Tab> or <Shift> + <Tab> keys to move between the hour, minute, and
second fields.
System Date [XX/XX/XXXX]
Sets your system to the date that you specify (usually the current date). The
format is month, day, year. Valid values for month, day, and year are Month:
(1 to 12), Day: (1 to 31), Year: (100 year range). Use the <Tab> or <Shift>
+ <Tab> keys to move between the month, day, and year fields.
Legacy Diskette A [1.44M, 3.5 in.], Legacy Diskette B [None]
Sets the type of floppy drives installed. Configuration options: [None]
[360K, 5.25 in.] [1.2M , 5.25 in.] [720K , 3.5 in.] [1.44M, 3.5 in.]
[2.88M, 3.5 in.]
Floppy 3 Mode Support [Disabled]
This is required to support older Japanese floppy drives. Floppy 3 Mode
support will allow reading and writing of 1.2MB (as opposed to 1.44MB)
on a 3.5-inch diskette. Configuration options: [Disabled] [Drive A]
[Drive B] [Both]
50
ASUS A7V-M User’s Manual
4. BIOS SETUP
4.3.1 Primary & Secondary Master/Slave
NOTE: Before attempting to configure a hard disk drive, make sure you
have the configuration information supplied by the manufacturer of the
drive. Incorrect settings may cause your system to not recognize the in-
stalled hard disk. To allow the BIOS to detect the drive type automati-
cally, select [Auto].
Type [Auto]
Select [Auto] to automatically detect an IDE hard disk drive. If automatic
detection is successful, the correct values will be filled in for the remaining
fields on this sub-menu. If automatic detection fails, your hard disk drive
may be too old or too new. You can try updating your BIOS or enter the
IDE hard disk drive parameters manually.
NOTE: After the IDE hard disk drive information has been entered into
BIOS, new IDE hard disk drives must be partitioned (such as with FDISK)
and then formatted before data can be read from and write on. Primary
IDE hard disk drives must have its partition set to active (also possible
with FDISK).
Other options for the Type field are:
[None] - to disable IDE devices
ASUS A7V-M User’s Manual
51
4. BIOS SETUP
IMPORTANT: If your hard disk was already formatted on an older previous system,
incorrect parameters may be detected. You will need to enter the correct parameters
manually or use low-level format if you do not need the data stored on the hard disk.
If the parameters listed differ from the ones used when the disk was formatted, the
disk will not be readable. If the auto-detected parameters do not match the ones that
should be used for your disk, you should enter the correct ones manually by setting
[User Type HDD].
[User Type HDD]
Manually enter the number of cylinders, heads and sectors per track for
your drive. Refer to your drive documentation or look on the drive for this
information. If no drive is installed or if you are removing a drive and not
replacing it, select [None].
Translation Method [LBA]
Select the hard disk drive type in this field. When Logical BlockAddressing
is enabled, 28-bit addressing of the hard drive is used without regard for
cylinders, heads, or sectors. Note that LBA Mode is necessary for drives
with greater than 504MB in storage capacity. Configuration options: [LBA]
[LARGE] [Normal] [Match Partition Table] [Manual]
Cylinders
This field configures the number of cylinders. Refer to your drive docu-
mentation to determine the correct value to enter into this field. NOTE: To
make changes to this field, the Type field must be set to [User Type HDD]
and the Translation Method field must be set to [Manual].
52
ASUS A7V-M User’s Manual
4. BIOS SETUP
Head
This field configures the number of read/write heads. Refer to your drive
documentation to determine the correct value to enter into this field. NOTE:
To make changes to this field, the Type field must be set to [User Type
HDD] and the Translation Method field must be set to [Manual].
Sector
This field configures the number of sectors per track. Refer to your drive
documentation to determine the correct value to enter into this field. NOTE:
To make changes to this field, the Type field must be set to [User Type
HDD] and the Translation Method field must be set to [Manual].
CHS Capacity
This field shows the drive’s maximum CHS capacity calculated automati-
cally by the BIOS from the drive information you entered.
Maximum LBA Capacity
This field shows the drive’s maximum LBA capacity calculated automati-
cally by the BIOS from the drive information you entered.
Multi-Sector Transfers [Maximum]
This option automatically sets the number of sectors per block to the high-
est number supported by the drive. This field can also be configured manu-
ally. Note that when this field is automatically configured, the set value may
not always be the fastest value for the drive. Refer to the documentation that
came with your hard drive to determine the optimal value and set it manu-
ally. NOTE: To make changes to this field, the Type field must be set to
[User Type HDD]. Configuration options: [Disabled] [2 Sectors] [4 Sec-
tors] [8 Sectors] [16 Sectors] [32 Sectors] [Maximum]
SMART Monitoring [Disabled]
This allows the enabling or disabling of the S.M.A.R.T. (Self-Monitoring,
Analysis and Reporting Technology) system which utilizes internal hard
disk drive monitoring technology. This feature is normally disabled because
system resources used in this feature may decrease system performance.
Configuration options: [Disabled] [Enabled]
PIO Mode [4]
This option lets you set a PIO (Programmed Input/Output) mode for the
IDE device. Modes 0 through 4 provide successively increased performance.
Configuration options: [0] [1] [2] [3] [4]
Ultra DMA Mode [Disabled]
Ultra DMA capability allows improved transfer speeds and data integrity
for compatible IDE devices. Set to [Disabled] to suppress Ultra DMA capa-
bility. NOTE: To make changes to this field, the Type field must be set to
[User Type HDD]. Configuration options: [0] [1] [2] [3] [4] [Disabled]
ASUS A7V-M User’s Manual
53
4. BIOS SETUP
Other options for “Type:” are:
[CD-ROM] - for IDE CD-ROM drives
[LS-120] - for LS-120 compatible floppy disk drives
[ZIP-100] - for ZIP-100 compatible disk drives
[MO] - for IDE magneto optical disk drives
[Other ATAPI Device] - for IDE devices not listed here
After using the legend keys to make your selections on this sub-menu, press
the <Esc> key to exit back to the Main menu. When the Main menu ap-
pears, you will notice that the drive size appear in the field for the hard disk
drive that you just configured.
4.3.2 Keyboard Features
Boot Up NumLock Status [On]
This field enables users to activate the Number Lock function upon system
boot. Configuration options: [Off] [On]
Keyboard Auto-Repeat Rate [12/Sec]
This controls the speed at which the system registers repeated keystrokes.
Options range from 6 to 30 characters per second. Configuration options:
[6/Sec] [8/Sec] [10/Sec] [12/Sec] [15/Sec] [20/Sec] [24/Sec] [30/Sec]
Keyboard Auto-Repeat Delay [1/4 Sec]
This field sets the time interval for displaying the first and second charac-
ters. Configuration options: [1/4 Sec] [1/2 Sec] [3/4 Sec] [1 Sec]
54
ASUS A7V-M User’s Manual
4. BIOS SETUP
Language [English]
This allows selection of the BIOS’displayed language. Currently only English is available.
Supervisor Password [Disabled] / User Password [Disabled]
These fields allow you to set the passwords. To set the password, highlight the appro-
priate field and press <Enter>. Type in a password and press <Enter>. You can type up
to eight alphanumeric characters. Symbols and other keys are ignored. To confirm the
password, type the password again and press the <Enter>. The password is now set to
[Enabled]. This password allows full access to the BIOS Setup menus. To clear the
password, highlight this field and press <Enter>. The same dialog box as above will
appear. Press <Enter> and the password will be set to [Disabled].
A Note about Passwords
The BIOS Setup program allows you to specify passwords in the Main menu. The pass-
words control access to the BIOS during system startup. The passwords are not case sen-
sitive. In other words, it makes no difference whether you enter a password using upper or
lowercase letters. The BIOS Setup program allows you to specify two separate passwords:
a Supervisor password and a User password. When disabled, anyone may access all BIOS
Setup program functions. When enabled, the Supervisor password is required for entering
the BIOS Setup program and having full access to all configuration fields.
Forgot the Password?
If you forgot the password, you can clear the password by erasing the CMOS Real
Time Clock (RTC) RAM. The RAM data containing the password information is
powered by the onboard button cell battery. To erase the RTC RAM: (1) Unplug
your computer, (2) Short the solder points, (3) Turn ON your computer, (4) Hold
down <Delete> during bootup and enter BIOS setup to re-enter user preferences.
Halt On [All Errors]
This field determines which types of errors will cause the system to halt.
Configuration options: [All Errors] [No Error] [All but Keyboard] [All but
Disk] [All but Disk/Keyboard]
Installed Memory [XXX MB]
This display-only field displays the amount of conventional memory detected
by the system during bootup. You do not need to make changes to this field.
ASUS A7V-M User’s Manual
55
4. BIOS SETUP
4.4 Advanced Menu
Operating Frequency Setting [User Define]
When the motherboard is set to JumperFree™ mode, this field allows you
to configure the external frequency of your CPU. Select [User Define] if
you want to make changes to the CPU Frequency field. When [Standard]
is selected, CPU (external) Frequency will be fixed at 100MHz. Configu-
ration options: [Standard] [User Define]
CPU Frequency (when Operating Frequency Setting
is set to [User Define])
This feature tells the clock generator what frequency to send to
the system bus and PCI bus. The bus frequency (external fre-
quency) multiplied by the bus multiple equals the CPU speed
(the CPU’s internal frequency). Note that selecting a frequency
higher than what the CPU manufacturer recommends may cause the system to
hang or crash. See System Hangup later in this section.
DRAM Frequency
This field determines whether the memory clock frequency is set to be in
synchronous or asynchronous mode with respect to the CPU Frequency.
This must be set in conjunction with CPU (external) Frequency to match
the speed of your SDRAM. When you press <Enter> on this field, the first
available option in the pop-up menu equals the CPU Frequency you select
for the previous field, and the second available option is the CPU Frequency
multiplied by 4/3. To maintain and ensure system stability, DRAM Fre-
quency is set to [100 MHz] when the BIOS setup default settings are loaded/
selected.
56
ASUS A7V-M User’s Manual
4. BIOS SETUP
CPU Level 1 Cache, CPU Level 2 Cache [Enabled]
These fields allow you to choose from the default of [Enabled] or choose
[Disabled] to turn on or off the CPU’s Level 1 and Level 2 built-in cache.
Configuration options: [Disabled] [Enabled]
CPU Level 2 Cache ECC Check [Disabled]
This function controls the ECC capability in the CPU level 2 cache. Con-
figuration options: [Disabled] [Enabled]
BIOS Update [Enabled]
This functions as an update loader integrated into the BIOS to supply the
processor with the required data. In the default position of [Enabled], the
BIOS will load the update on all processors during system bootup. Configu-
ration options: [Disabled] [Enabled]
PS/2 Mouse Function Control [Auto]
The default of [Auto] allows the system to detect a PS/2 mouse on startup.
If detected, IRQ12 will be used for the PS/2 mouse. IRQ12 will be reserved
for expansion cards only if a PS/2 mouse is not detected. [Enabled] will
always reserve IRQ12, whether on startup a PS/2 mouse is detected or not.
Configuration options: [Enabled] [Auto]
USB Legacy Support [Auto]
This motherboard supports Universal Serial Bus (USB) devices. The de-
fault of [Auto] allows the system to detect a USB device on startup. If de-
tected, the USB controller will be enabled. If not detected, the USB control-
ler will be disabled. When this field is set to [Disabled], the USB controller
is disabled no matter whether you are using a USB device or not. Configu-
ration options: [Disabled] [Enabled] [Auto]
OS/2 Onboard Memory > 64M [Disabled]
When using OS/2 operating systems with installed DRAM of greater than
64MB, you need to set this option to [Enabled]; otherwise, leave this on
[Disabled]. Configuration options: [Disabled] [Enabled]
ASUS A7V-M User’s Manual
57
4. BIOS SETUP
Notes for JumperFree Mode
System Hangup
If your system crashes or hangs due to improper frequency settings, power
OFF your system and restart. The system will start up in safe mode running
at a DRAM-to-CPU frequency ratio of 3:3 and a bus speed of 100MHz. You
will then be led to BIOS setup to adjust the configurations.
58
ASUS A7V-M User’s Manual
4. BIOS SETUP
4.4.1 Chip Configuration
(Scroll down to see more items as shown.)
Onboard PCI IDE Enable [Both]
You can select to enable the primary IDE channel, secondary IDE channel,
both, or disable both channels. Configuration options: [Both] [Primary] [Sec-
ondary] [Disabled]
Spread Spectrum Control [Enabled]
Leave on default setting. Spread spectrum typically reduces system electro-
magnetic interference (EMI) by 8dB to 10dB.
AGP 4X Drive Strength [Auto]
Configuration options: [Auto] [Manual]
AGP Drive Strength P Ctrl [C](When AGP 4X Drive Strength set to [Manual])
Configuration options: [0] [1] [2]...[F]
AGP Drive Strenght N Ctrl [E](When AGP 4X Drive Strength set to [Manual])
Configuration options: [0] [1] [2]...[F]
AGP Fast Write [Disabled]
Configuration options: [Disabled] [Enabled]
ASUS A7V-M User’s Manual
59
4. BIOS SETUP
SDRAM Configuration [By SPD]
This sets the optimal timings for SDRAM related fields, depending on the
memory modules that you are using. Default setting is [By SPD], which
configures the subsequent 3 items by reading the contents in the SPD (Se-
rial Presence Detect) device. The EEPROM on the memory module stores
critical parameter information about the module, such as memory type, size,
speed, voltage interface, and module banks. Configuration options: [User
Define] [7ns(143MHz)] [8ns(125MHz)] [By SPD]
SDRAM CAS Latency
This controls the latency between the SDRAM read command and the time
that the data actually becomes available. NOTE: This field will only be ad-
justable when SDRAM Configuration is set to [User Define].
SDRAM RAS Precharge Time
This controls the idle clocks after issuing a precharge command to the
SDRAM. NOTE: This field will only be adjustable when SDRAM Con-
figuration is set to [User Define].
SDRAM RAS to CAS Delay
This controls the latency between the SDRAM active command and the
read/write command. NOTE: This field will only be adjustable when
SDRAM Configuration is set to [User Define].
PCI Master Read Caching
Default: [Enabled] for Athlon Processors / [Disabled] for Duron Processors
Leave on default setting. Configuration options: [Disabled] [Enabled]
Delayed Transaction [Disabled]
Default: [Enabled] for Athlon Processors / [Disabled] for Duron Processors
Leave on default setting. Enabled, this frees the PCI Bus when the CPU is
accessing 8-bit ISA devices that normally consume about 50-60 PCI Clocks
without PCI delayed transaction. Select [Disabled] for ISA devices that are
not PCI 2.1 compliant. Configuration options: [Disabled] [Enabled]
PCI to DRAM Prefetch [Enabled]
Configuration options: [Disabled] [Enabled]
Byte Merge [Disabled]
To optimize the data transfer on PCI, this merges a sequence of individual
memory writes (bytes or words) into a single 32-bit block of data. However,
byte merging may only be done when the bytes within a data phase are in a
prefetchable address range. Configuration options: [Disabled] [Enabled]
DRAM Read Latch Delay [Auto]
Configuration options: [-0.01 ns] [0.75 ns]...[Auto]
60
ASUS A7V-M User’s Manual
4. BIOS SETUP
Memory Early/Delay Write [Auto]
Configuration options: [0.0 ns] [0.5 ns]...[Auto]
Memory Data Driving [Auto]
Configuration options: [Auto] [Strong] [Weak]
Memory Address Driving [Auto]
Configuration options: [Auto] [Strong] [Weak]
DIMM Interleave Setting [Auto]
Configuration options: [Auto] [Disabled]
I/O Recovery Time [Disabled]
Configuration options: [Disabled] [Enabled]
Graphics Aperture Size [64MB]
This feature allows you to select the size of mapped memory forAGPgraphic
data. Configuration options: [4MB] [8MB] [16MB] [32MB] [64MB]
[128MB] [256MB]
Video Memory Cache Mode [UC]
USWC (uncacheable, speculative write combining) is a new cache technol-
ogy for the video memory of the processor. It can greatly improve the dis-
play speed by caching the display data. You must set this to UC (uncacheable)
if your display card cannot support this feature; otherwise your system may
not boot. Configuration options: [UC] [USWC]
ASUS A7V-M User’s Manual
61
4. BIOS SETUP
4.4.2 I/O Device Configuration
Onboard FDC Swap A & B [No Swap]
This field allows you to reverse the hardware drive letter assignments of
your floppy disk drives. Configuration options: [No Swap] [Swap AB]
Floppy Disk Access Control [R/W]
When set to [Read Only], this field protects files from being copied to floppy
disks by allowing reads from the floppy disk drive but not writes. The setup
default [R/W] allows both reads and writes. Configuration options: [R/W]
[Read Only]
Onboard Serial Port 1 [3F8H/IRQ4]
Onboard Serial Port 2 [2F8H/IRQ3]
These fields allow you to set the addresses for the onboard serial connec-
tors. Serial Port 1 and Serial Port 2 must have different addresses. Configu-
ration options: [3F8H/IRQ4] [2F8H/IRQ3] [3E8H/IRQ4] [2E8H/IRQ10]
[Disabled]
UART2 Use Infrared [Disabled]
When enabled, this field activates the onboard standard infrared feature and sets the
second serial UART to support the infrared module connector on the motherboard. If
your system already has a second serial port connected to the onboard COM2 connec-
tor, it will no longer work if you enable the infrared feature. See Standard and Con-
sumer Infrared Module Connector in 3.8 External Connectors. Configuration op-
tions: [Disabled] [Enabled]
62
ASUS A7V-M User’s Manual
4. BIOS SETUP
Onboard Parallel Port [378H/IRQ7]
This field sets the address of the onboard parallel port connector. If you disable this
feature, Parallel Port Mode and ECP DMA Select configurations will not be avail-
able. Configuration options: [Disabled] [378H/IRQ7] [278H/IRQ5]
Parallel Port Mode [ECP+EPP]
This field allows you to set the operation mode of the parallel port. [Normal] allows
normal-speed operation but in one direction only; [EPP] allows bidirectional parallel
port operation; [ECP] allows the parallel port to operate in bidirectional DMA mode;
[ECP+EPP] allows normal speed operation in a two-way mode. Configuration op-
tions: [Normal] [ECP] [EPP] [ECP+EPP]
ECP DMA Select [3]
This field allows you to configure the parallel port DMA channel for the selected ECP
mode. This selection is available only if you select [ECP] or [ECP+EPP] in Parallel
Port Mode above. Configuration options: [1] [3]
Onboard Peripheral Resource Control
Onboard Network Controller [Enabled]
Onboard AC97 Audio Controller [Auto]
[Auto] allows the motherboard’s BIOS to detect whether you are using any
network/audio device. If a network/audio device is detected, the onboard
network/audio controller will be enabled; if no network/audio device is de-
tected, the onboard network/audio controller will be disabled. If you have
conflicts with the onboard network/audio controller, you may set the appro-
priate field to [Disabled]. Configuration options: [Enabled] [Disabled]
ASUS A7V-M User’s Manual
63
4. BIOS SETUP
Onboard Legacy Audio Support [Disabled]
The onboard chipset is integrated with a SoundBlaster Pro controller. To
use it, you must enable this field. Leave on the default setting [Disabled] if
you want to use an add-on audio device. NOTE: To display the rest of the
setup items, this field must be enabled (as shown below).
Sound Blaster Emulation [Disabled]
Select [Enabled] for this field if you want to use the Sound Blaster™ emu-
lation feature.
Sound Blaster I/O Base Address [220h-22Fh]
Sound Blaster IRQ [IRQ5]
Sound Blaster DMA [DMA 1]
These fields set the I/O address, IRQ, and DMA channel for the Sound
Blaster™ feature.
MPU 401 [Enabled]
Enable this field if you want to use the MIDI device onboard.
MPU 401 I/O Base Address [300h-303h]
This sets the I/O address for the onboard MIDI device.
FM Enable (388h-38Bh) [Disabled]
This field enables or disables the FM modulation feature.
Game Port Function [Disabled]
Enable this field to use the game port. Configuration options: [Disabled]
[Enable (200h-207h)]
64
ASUS A7V-M User’s Manual
4. BIOS SETUP
4.4.3 PCI Configuration
Slot 1, Slot 2, Slot 3 IRQ [Auto]
These fields set how IRQ use is determined for each PCI slot. The default
setting for each field is [Auto], which utilizes auto-routing to determine
IRQ use. Configuration options: [Auto] [NA] [3] [4] [5] [7] [9] [10] [11]
[12] [14] [15]
PCI/VGA Palette Snoop [Disabled]
Some nonstandard VGAcards, such as graphics accelerators or MPEG video
cards, may not show colors properly. The setting [Enabled] should correct
this problem. Otherwise, leave this on the default setting of [Disabled].
Configuration options: [Disabled] [Enabled]
PCI Latency Timer [32]
Leave on default setting for best performance vs. stability.
SYMBIOS SCSI BIOS [Auto]
[Auto] allows the motherboard’s BIOS to detect whether you have a Symbios
SCSI card. If the Symbios SCSI card is detected, the motherboard’s Symbios
BIOS will be enabled; if no Symbios SCSI card is detected, the onboard
Symbios SCSI BIOS will be disabled.
[Disabled] will disable the motherboard’s Symbios SCSI BIOS so that the
BIOS on an add-on Symbios SCSI card can be used. If your Symbios SCSI
card does not have a BIOS, the Symbios SCSI card will not function. Con-
figuration options: [Auto] [Disabled]
ASUS A7V-M User’s Manual
65
4. BIOS SETUP
USB Function [Enabled]
This motherboard supports Universal Serial Bus (USB) devices. Set to [En-
abled] if you want to use USB devices. Configuration options: [Disabled]
[Enabled]
Primary VGA BIOS [PCI Card]
If your computer has both PCI andAGP VGA cards, this field allows ¥ou to
select which of the cards will act as your primary graphics card. [AGP Card]
uses the AGP card as your primary card. The default, [PCI Card], allows
your PCI graphics card to take precedence when detected. Configuration
options: [PCI Card] [AGP Card]
PCI/PNP IRQ Resource Exclusion
IRQ XX Reserved for Legacy Device [No/ICU]
These fields indicate whether or not the displayed IRQ for each field is
being used by an onboard legacy (non-PnP) device. The default value indi-
cates either that the displayed IRQ is not used or that ISA Configuration
Utility (ICU) is being used to determine if a legacy device is using that IRQ.
Configuration options: [No/ICU] [Yes]
66
ASUS A7V-M User’s Manual
4. BIOS SETUP
PCI/PNP DMA Resource Exclusion
DMA x Reserved for Legacy Device [No/ICU]
These fields indicate whether or not the displayed DMA channel for each
field is being used by an onboard legacy (non-PnP) device. The default
setting indicates either that the displayed DMA channel is not used or an
ICU is being used to determine if an ISA device is using that channel. Con-
figuration options: [No/ICU] [Yes]
ASUS A7V-M User’s Manual
67
4. BIOS SETUP
PCI/PNP UMB Resource Exclusion
Reserved MEM Block BASE [No/ICU]
This field allows you to set the base address and block size of an onboard
legacy ISA device that uses any memory segment within the C800 and DFFF
address range. If you have such a device and you are not using an ICU to
specify its address range, select a base address from the six available op-
tions; the Reserved MEM Block SIZE field will then appear for selecting
the block size. If you have more than one legacy device onboard that re-
quires the use of this address range, you can increase the block size to 8K,
16K, 32K, or 64K. If you are using an ICU to accomplish this task, leave
Reserved MEM Block BASE to its default setting of [No/ICU]. Configu-
ration options: [No/ICU] [C800] [CC00] [D000] [D400] [D800] [DC00]
68
ASUS A7V-M User’s Manual
4. BIOS SETUP
4.4.4 Shadow Configuration
Video ROM BIOS Shadow [Enabled]
This field allows you to change the video BIOS location from ROM to
RAM. Relocating to RAM enhances system performance, as information
access is faster than the ROM. Configuration options: [Disabled] [Enabled]
C8000-DFFFF Shadow [Disabled]
These fields are used for shadowing other expansion card ROMs. If you
install other expansion cards with ROMs on them, you will need to know
which addresses the ROMs use to shadow them specifically. Shadowing a
ROM reduces the memory available between 640K and 1024K by the amount
used for this purpose. Configuration options: [Disabled] [Enabled]
ASUS A7V-M User’s Manual
69
4. BIOS SETUP
4.5 Power Menu
The Power menu allows you to reduce power consumption. This feature turns off the
video display and shuts down the hard disk after a period of inactivity.
Power Management [User Define]
This option must be enabled to use any of the automatic power saving features. If
this menu item is set to [Disabled], power management features will not function
regardless of other field settings on this menu. The [User Define] option allows you
to make your own selections in the Power menu. When set to [Max Saving], system
power will be conserved to its greatest amount. The Suspend Mode field will then
be set to predefined value that ensures maximum power savings.
This field acts as the master control for the power management modes. [Max Sav-
ing] puts the system into power saving mode after a brief period of system inactiv-
ity; [Min Saving] is almost the same as [Max Saving] except that the system inactiv-
ity period is longer; [Disabled] disables the power saving features; [User Define]
allows you to set power saving options according to your preference. Configuration
options: [User Define] [Disabled] [Min Saving] [Max Saving]
IMPORTANT: Advanced Power Management (APM) should be installed to keep
the system time updated when the computer enters suspend mode activated by
the BIOS Power Management. For DOS environments, you need to add the
statement, DEVICE=C:\DOS\POWER.EXE, to your CONFIG.SYS file. For
Windows 3.x and Windows 95, you need to install Windows with the APM
feature. For Windows 98 and later, APM is automatically installed. A battery
and power cord icon labeled “Power Management” will appear in the “Control
Panel.” Choose “Advanced” in the Power Management Properties dialog box.
70
ASUS A7V-M User’s Manual
4. BIOS SETUP
Video Off Option [Suspend -> Off ]
This field determines when to activate the video off feature for monitor
power management. Configuration options: [Always On] [Suspend -> Off]
Video Off Method [DPMS OFF]
This field defines the video off features. The DPMS (Display Power Manage-
ment System) feature allows the BIOS to control the video display card if it
supports the DPMS feature. [Blank Screen] only blanks the screen (use this
for monitors without power management or “green” features. If set up in your
system, your screen saver will not display with [Blank Screen] selected). [V/
H SYNC+Blank] blanks the screen and turns off vertical and horizontal scan-
ning. Configuration options: [Blank Screen] [V/H SYNC+Blank] [DPMS
Standby] [DPMS Suspend] [DPMS OFF] [DPMS Reduce ON]
HDD Power Down [Disabled]
Shuts down any IDE hard disk drives in the system after a period of inac-
tivity as set in this user-configurable field. This feature does not affect
SCSI hard drives. Configuration options: [Disabled] [1 Min] [2 Min] [3
Min]...[15 Min]
Suspend Mode [Disabled]
Sets the time period before the system goes into suspend mode. Configu-
ration options: [Disabled] [30 Sec] [1 Min]... [40 Min]
PWR Button < 4 Secs [Soft Off]
When set to [Soft off], the ATX switch can be used as a normal system
power-off button when pressed for less than 4 seconds. [Suspend] allows
the button to have a dual function where pressing less than 4 seconds will
place the system in sleep mode. Regardless of the setting, holding the ATX
switch for more than 4 seconds will power off the system. Configuration
options: [Soft off] [Suspend]
ASUS A7V-M User’s Manual
71
4. BIOS SETUP
4.5.1 Power Up Control
AC PWR Loss Restart [Disabled]
This allows you to set whether you want your system to reboot after the
power has been interrupted. [Disabled] leaves your system off and [En-
abled] reboots your system. [Previous State] sets your system back to the
state it is before the power interruption. Configuration options: [Disabled]
[Enabled] [Previous State]
PWR Up On External Modem Act [Enabled]
This allows either settings of [Enabled] or [Disabled] for powering up the
computer when the external modem receives a call while the computer is in
Soft-off mode. NOTE: The computer cannot receive or transmit data until
the computer and applications are fully running. Thus connection cannot be
made on the first try. Turning an external modem off and then back on while
the computer is off causes an initialization string that will also cause the
system to power on. Configuration options: [Disabled] [Enabled]
Wake On LAN or PCI Modem [Disabled]
Wake-On-LAN/PCI Modem allows your computer to be booted from an-
other computer via a network by sending a wake-up frame or signal. Con-
figuration options: [Disabled] [Enabled]
IMPORTANT:This feature requires an optional network interface card with Wake-
On-LAN and an ATX power supply with at least 720mA +5V standby power.
72
ASUS A7V-M User’s Manual
4. BIOS SETUP
Automatic Power Up [Disabled]
This allows an unattended or automatic system power up. You may config-
ure your system to power up at a certain time of the day by selecting [Every-
day] or at a certain time and day by selecting [By Date]. NOTE: Automatic
Power Up will not work if the system is powered down by operating sys-
tems, such as Windows 98, that have ACPI support enabled. Configuration
options: [Disabled] [Everyday] [By Date]
ASUS A7V-M User’s Manual
73
4. BIOS SETUP
4.5.2 Hardware Monitor
MB Temperature [xxxC/xxxF]
CPU Temperature [xxxC/xxxF]
The onboard hardware monitor is able to detect the MB (motherboard) and
CPU temperatures. Set to [Ignore] only if necessary.
CPU Fan Speed [xxxxRPM]
Chassis Fan Speed [xxxxRPM]
The onboard hardware monitor is able to detect the CPU fan speed and the
chassis fan speed in rotations per minute (RPM). The presence of the fans is
automatically detected. Set to [Ignore] only if necessary.
VCORE Voltage, +3.3V Voltage, +5V Voltage, +12V Voltage [xx.xxV]
686A Voltage
The onboard hardware monitor is able to detect the voltage output by the
onboard voltage regulators. Set to [Ignore] only if necessary.
NOTE: If any of the monitored items is out of range, an error message will
appear: “Hardware Monitor found an error. Enter Power setup menu for
details”. You will then be prompted to “Press F1 to continue, DEL to enter
SETUP”.
74
ASUS A7V-M User’s Manual
4. BIOS SETUP
4.6 Boot Menu
Boot Sequence
The Boot menu allows you to select among the four possible types of boot
devices listed using the up and down arrow keys. By using the <+> or <Space>
key, you can promote devices and by using the <-> key, you can demote
devices. Promotion or demotion of devices alters the priority which the sys-
tem uses to search for a boot device on system power up. Configuration fields
include Removable Devices, IDE Hard Drive, ATAPI CD-ROM, and Other
Boot Device.
Removable Device [Legacy Floppy]
Configuration options: [Disabled] [Legacy Floppy] [LS120] [ZIP-100]
[ATAPI MO] [USB FDD] [USB ZIP]
IDE Hard Drive
This field allows you to select which IDE hard disk drive to use in the boot
sequence. Pressing [Enter] will show the product IDs of all connected IDE
hard disk drives.
ATAPI CD-ROM
This field allows you to select which ATAPI CD-ROM drive to use in the
boot sequence. Pressing [Enter] will show the product IDs of all your con-
nected ATAPI CD-ROM drives.
IMPORTANT: Make sure the ATAPI CD-ROM drive that you want to use in the
boot sequence is connected to either the PRIMARY or SECONDARY IDE con-
nectors, not to the ATA100 connectors. Currently, the Promise® Ultra DMA/100
chip does not support this feature.
ASUS A7V-M User’s Manual
75
4. BIOS SETUP
Other Boot Device Select [INT18 Device (Network)]
Configuration options: [Disabled] [SCSI/OnboardATABoot Device] [INT18
Device (Network)] [LANDesk (R) Service Agent]
Plug & Play O/S [No]
This field allows you to use a Plug-and-Play (PnP) operating system to con-
figure the PCI bus slots instead of using the BIOS. When [Yes] is selected,
interrupts may be reassigned by the OS. When a non-PnP OS is installed or
you want to prevent reassigning of interrupt settings, select the default set-
ting of [No]. Configuration options: [No] [Yes]
Reset Configuration Data [No]
The Extended System Configuration Data (ESCD) contain information about
non-PnP devices. It can also hold the complete record of how the system
was configured the last time it was booted. Select [Yes] only if you want to
clear these data during the Power-On Self Test (POST). Configuration op-
tions: [No] [Yes]
Boot Virus Detection [Enabled]
This field allows you to set boot virus detection, ensuring a virus-free boot
sector. The system halts and displays a warning message when it detects a
virus. If this occurs, you can either allow the operation to continue or use a
virus-free bootable floppy disk to restart and investigate your system. Con-
figuration options: [Disabled] [Enabled]
Quick Power On Self Test [Enabled]
This field speeds up the Power-On-Self Test (POST) routine by skipping
retesting a second, third, and fourth time. Configuration options: [Disabled]
[Enabled]
Boot Up Floppy Seek [Disabled]
When enabled, the BIOS will seek the floppy disk drive to determine whether
the drive has 40 or 80 tracks. Configuration options: [Disabled] [Enabled]
76
ASUS A7V-M User’s Manual
4. BIOS SETUP
4.7 Exit Menu
Once you have made all of your selections from the various menus in the Setup pro-
gram, you should save your changes and exit Setup. Select Exit from the menu bar to
display the following menu:
NOTE: Pressing <Esc> does not exit this menu. You must select one of the
options from this menu or <F10> from the legend bar to exit this menu.
Exit Saving Changes
Once you are finished making your selections, choose this option from the
Exit menu to ensure the values you selected are saved to the CMOS RAM.
The CMOS RAM is sustained by an onboard backup battery and stays on
even when the PC is turned off. Once this option is selected, a confirmation
is asked. Select [Yes] to save changes and exit.
NOTE: If you attempt to exit the Setup program without saving your
changes, the program will prompt you with a message asking if you want
to save your changes before exiting. Pressing <Enter> will then save changes
while exiting.
Exit Discarding Changes
This option should only be used if you do not want to save the changes you
have made to the Setup program. If you have made changes to fields other
than system date, system time, and password, the system will ask for con-
firmation before exiting.
ASUS A7V-M User’s Manual
77
4. BIOS SETUP
Load Setup Defaults
This option allows you to load the default values for each of the parameters
on the Setup menus. When this option is selected or if <F5> is pressed, a
confirmation is requested. Select [Yes] to load default values. You can now
select Exit Saving Changes or make other changes before saving the val-
ues to the non-volatile RAM.
Discard Changes
This option allows you to discard the selections you made and restore the
values you previously saved. After selecting this option, a confirmation is
requested. Select [Yes] to discard any changes and load the previously saved
values.
Save Changes
This option saves your selections without exiting the Setup program. You
can then return to other menus and make changes. After selecting this op-
tion, all selections are saved and a confirmation is requested. Select [Yes] to
save any changes to the non-volatile RAM.
78
ASUS A7V-M User’s Manual
5. SOFTWARE SETUP
5.1 Install Operating System
You should always use the latest operating system and updates when using new
hardware to ensure full compliancy. You may use any version of Windows 98/2000/
Millenium, but for Windows 95, you must use OSR 2.0 or later. For Windows NT
4.0, you must use Service Pack 3.0 or later.
5.2 Start Windows
When you start Windows 98 for the first time after installing your motherboard,
Windows will detect all plug-and play devices. Follow theAdd New Hardware Wiz-
ard to install all necessary device drivers. When prompted to restart, select No and
then follow the setup procedures in this section.
NOTE: Because there are various motherboard settings, options, and expansion
cards, the following can only be used as a general reference and may not reflect
exactly the screen contents displayed on your screen.
ASUS A7V-M User’s Manual
79
5. SOFTWARE SETUP
5.3 A7V-M Series Motherboard Support CD
NOTE: The support CD contents are subject to change at any time without notice.
To begin using your support CD disc, just insert it into your CD-ROM drive and the
support CD installation menu should appear. If the menu does not appear, double-
click or run D:\ASSETUP.EXE (assuming that your CD-ROM drive is drive D:).
5.3.1 Installation Menu
•
•
•
•
•
•
•
•
VIA 4 in 1 drivers: Installs Bus Master PCI IDE Driver, AGP VxD Driver, VIA
Chipset Functions Registry, and IRQ Routing Miniport Driver.
Audio Driver: (optional) Installs the necessary audio drivers for the onboard au-
dio CODEC (optional).
Realtek RTL8139C PCI Fast Ethernet NIC Driver: (optional) Shows installa-
tion instructions for the Realtek NIC driver.
ASUS PC Probe Vx.xx: Installs a smart utility to monitor your computer’s fan,
temperature, and voltages.
ASUS Update Vx.xx: Installs ASUS\Update to help you update your BIOS or
download BIOS image file from the Internet.
YAMAHASoftSynthesizerS-YXG50:(optional) Installs theYamaha SoftSynthesizer
for playing MIDI files through software. Refer to the online help for more information.
PC-Cillin 98Vx.xx: Installs the PC-cillin virus protection software.View the online
help for more information.
ADOBE Acrobat Reader Vx.xx: Installs the Adobe Acrobat Reader software neces-
sary to view user’s manuals saved in PDF format. Updated or other language versions of
this motherboard's manual is available in PDF format at any of our web sites.
Install Cyberlink Video and Audio Applications: (optional) Installs Cyberlink
PowerPlayer SE, PowerDVD Trial, and Cyberlink VideoLive Mail.
Show Motherboard Information: Allows you to view information about your
motherboard, such as product name, BIOS version, and CPU.
Browse Support CD: Allows you to view the contents of the CD.
•
•
•
(TO SEE THE FOLLOWING ITEMS, CLICK RIGHT ARROW ON THE LOWER-RIGHT CORNER OF THE
MAIN MENU)
•
•
ReadMe: Allows you to view the support CD file list and contact information.
Exit: Exits the CD installation menu.
(TO RETURN TO THE MAIN MENU, CLICK LEFTARROW ON THE LOWER-RIGHT CORNER OF THE
SECONDARY MENU)
Additonal CD Content: Flash BIOS writer in the AFLASH folder
80
ASUS A7V-M User’s Manual
5. SOFTWARE SETUP
5.4 VIA 4 in 1 drivers
Insert the Support CD that came with your motherboard into your CD-ROM drive
or double-click the CD drive icon in My Computer to bring up the setup screen.
(2) Click here to open the VIA
Service Pack 1 README
dialog box. (3) Click Yes on
the box after you have read
and agreed to the README
and agreement.
(1) Click here.
(4) Select preferred options
and then click here.
(5) Click here.
(6) Click here and then click
Next if you want to enable
DMA mode. Otherwise,
just click Next
(7) Click here.
(9) Click here and then click
Finish to restart your
computer.
(8) Click here.
ASUS A7V-M User’s Manual
81
5. SOFTWARE SETUP
5.5 Audio Driver
Insert the Support CD that came with your motherboard into your CD-ROM drive
or double-click the CD drive icon in My Computer to bring up the setup screen.
(1) Click here.
(2) Click here.
(4) Click here and then click
(3) Click here.
Finish to restart your
computer.
* You may choose to restart your computer later when this option is offered,
especially if you still want to install other drivers and/or software. You may
not, however, be able to use immediately the devices associated with the driv-
ers or software because these drivers need to be enabled. These drivers are
enabled when Windows starts/restarts.
82
ASUS A7V-M User’s Manual
5. SOFTWARE SETUP
5.6 Realtek RTL8139C PCI Fast Ethernet NIC Driver
Insert the Support CD that came with your motherboard into your CD-ROM drive
or double-click the CD drive icon in My Computer to bring up the setup screen.
(1) Click here to
open setup
instructions
(see below).
ASUS A7V-M User’s Manual
83
5. SOFTWARE SETUP
5.7 ASUS PC Probe Vx.xx
Insert the Support CD that came with your motherboard into your CD-ROM drive
or double-click the CD drive icon in My Computer to bring up the setup screen.
NOTE: ASUS PC Probe will not run if another hardware monitoring utility is in-
stalled. To uninstall any program, see 5.7 Uninstalling Programs.
(1) Click here.
(2) Click here.
(4) Click here.
(3) Click here.
(5) Click here.
(6) Click here.
(7) Click Next to select a
folder for the program
items and then (8) click
Next for Setup to start
copying the necessary files.
(9) Click here to accept the
default selections and to
complete Setup.
84
ASUS A7V-M User’s Manual
5. SOFTWARE SETUP
5.8 ASUS Update Vx.xx
Insert the Support CD that came with your motherboard into your CD-ROM drive
or double-click the CD drive icon in My Computer to bring up the setup screen.
(1) Click here.
(2) Click here.
(4) Click here.
(3) Click here.
(5) Click here.
* You may choose to restart your computer later when this option is offered,
especially if you still want to install other drivers and/or software. You may
not, however, be able to use immediately the devices associated with the driv-
ers or software because these drivers need to be enabled. These drivers are
enabled when Windows starts/restarts.
ASUS A7V-M User’s Manual
85
5. SOFTWARE SETUP
5.9 YAMAHA Soft Synthesizer S-YXG50
Insert the Support CD that came with your motherboard into your CD-ROM drive
or double-click the CD drive icon in My Computer to bring up the setup screen.
NOTE: Make sure that you have uninstalled any old version of the YAMAHA
SoftSynthesizer/XGplayer before installing this version. If you can’t uninstall your
old version using the procedures in 5.13 Uninstalling Programs, see the README.TXT
files under the Yamaha folder of your support CD for uninstallation information.
(2) Click here.
(1) Click here.
(3) Enter the information
(4) Click here.
requested and click here.
(5) Click here and then respond
accordingly when prompted
(6) & (7) below
(8) Click here.
(6)
(9) Click here and then click
OK to restart your
computer.
(7)
86
ASUS A7V-M User’s Manual
5. SOFTWARE SETUP
5.10 PC-Cillin 98 Vx.xx
Insert the Support CD that came with your motherboard into your CD-ROM drive
or double-click the CD drive icon in My Computer to bring up the setup screen.
(1) Click here.
(2) Click here.
(4) Setup will proceed with
the installation if no
viruses are found. Click
here to start installation.
(3) Click here only after you have
read the License Agreement.
(6) & (7) Select the preferred features by
clicking the appropriate buttons.
(5) Click here.
(8) Insert a floppy disk and then click
here. Once the Emergency Clean
disk is created, click OK.
(9) Click here and then
click Finish to restart.
ASUS A7V-M User’s Manual
87
5. SOFTWARE SETUP
5.11 ADOBE Acrobat Reader Vx.xx
Insert the Support CD that came with your motherboard into your CD-ROM drive
or double-click the CD drive icon in My Computer to bring up the setup screen.
(1) Click here.
(2) Click here.
(3) Click here only after you have
read the License Agreement.
(4) Click here.
(5) Click OK to complete
Setup.
88
ASUS A7V-M User’s Manual
5. SOFTWARE SETUP
5.12 Cyberlink Video and Audio Applications
5.12.1 System Requirements
•
•
•
•
•
•
•
•
Pentium-100MHz PC compatible
Microsoft Windows 95/98/NT/2000
Hard disk drive with at least 10MB of free space
4x speed or above CD-ROM drive
Sound card with a Windows wave audio driver
256 (or above) color VGA card is required. A VGA card with
DirectDraw support
8MB system memory
5.12.2 Cyberlink Contact Information
ASUS A7V-M User’s Manual
89
5. SOFTWARE SETUP
5.12.3 Installation Procedures
Insert the Support CD that came with your motherboard into your CD-ROM drive
or double-click the CD drive icon in My Computer to bring up the setup screen.
(1) Click here.
(2) Click here.
(4) Click here and follow the
onscreen instructions to
complete installation.
(3) Click here.
(6) Click here and follow the
onscreen instructions to
complete installation.
(5) Click here to install
PowerDVD.
(7) Click here and follow the
onscreen instructions to
complete installation.
90
ASUS A7V-M User’s Manual
5. SOFTWARE SETUP
5.13 Uninstalling Programs
Add/Remove Programs is a basic component within Windows. You may use this
function if a program does not provide its own uninstallation program.
(1) Double-click here to open
the Add/Remove Programs
Properties dialog box.
(2) Select the program to
remove and click here.
(3) Click here.
ASUS A7V-M User’s Manual
91
5. SOFTWARE SETUP
(This page was intentionally left blank.)
92
ASUS A7V-M User’s Manual
6. SOFTWARE REFERENCE
6.1 ASUS PC Probe
ASUS PC Probe is a convenient utility to continuously monitor your com-
puter system’s vital components, such as fan rotations, voltages, and tem-
peratures. It also has a utility that lets you review useful information about
your computer, such as hard disk space, memory usage, and CPU type, CPU
speed, and internal/external frequencies through the DMI Explorer.
6.1.1 Starting ASUS PC Probe
WhenASUS PC Probe starts, a splash screen appears allowing you to select
whether to show the screen again when you open PC Probe or not. To by-
pass this startup screen, clear the Show up in next execution check box.
To open ASUS PC Probe, click the Windows Start button, point to Pro-
grams, and then ASUS Utility, and then click Probe Vx.xx.
The PC Probe icon
will appear on the taskbar’s system tray indicating
that ASUS PC Probe is running. Clicking the icon will allow you to see the
status of your PC.
ASUS A7V-M User’s Manual
93
6. SOFTWARE REFERENCE
6.1.2 Using ASUS PC Probe
Monitoring
Monitor Summary
Shows a summary of the items being
monitored.
Temperature Monitor
Shows the PC’s temperature (for
supported processors only).
Temperature Warning
threshold adjustment
(Move the slider up to increase the
threshold level or down to decrease
the threshold level)
Fan Monitor
Shows the PC’s fan rotation.
Fan Warning
threshold adjustment
(Move the slider up to increase the
threshold level or down to decrease
the threshold level)
Voltage Monitor
Shows the PC’s voltages.
94
ASUS A7V-M User’s Manual
6. SOFTWARE REFERENCE
Settings
Lets you set threshold levels and poll-
ing intervals or refresh times of the PC’s
temperature, fan rotation, and voltages.
CPU Cooling System Setup
Lets you select when to enable software CPU
cooling. When When CPU Overheated is selected,
the CPU cooling system is enabled whenever the
CPU temperature reaches the threshold value.
History
Lets you record the monitoring activ-
ity of a certain component of your PC
for future reference.
Fan Control
Lets you enable/disable Smart Fan
Control. Smart Fan Control adjusts the
fan speed automatically based on the
current CPU temperature and pre-
defined threshold.
NOTE: This feature is not available on
ASUS Probe version 2.12.01/2.12.02
Information
Hard Drives
Shows the used and free space of the
PC’s hard disk drives and the file allo-
cation table or file system used.
ASUS A7V-M User’s Manual
95
6. SOFTWARE REFERENCE
Memory
Shows the PC’s memory load, memory
usage, and paging file usage.
Device Summary
Shows a summary of devices in your PC.
DMI Explorer
Shows information pertinent to the PC,
such as CPU type, CPU speed, and in-
ternal/external frequencies, and memory
size.
Utility
Lets you run programs outside of the
ASUS Probe modules. To run a program,
click Execute Program. NOTE: This
feature is currently unavailable.
96
ASUS A7V-M User’s Manual
6. SOFTWARE REFERENCE
6.1.3 ASUS PC Probe Task Bar Icon
Right clicking the PC Probe
icon will bring up a menu to
open or exit ASUS PC Probe
and pause or resume all sys-
tem monitoring.
When the ASUS PC Probe
senses a problem with your
PC, portions of the ASUS PC
Probe icon changes to red, the
PC speaker beeps, and the
ASUS PC Probe monitor is dis-
played.
ASUS A7V-M User’s Manual
97
6. SOFTWARE REFERENCE
6.2 CyberLink PowerPlayer SE
CyberLink PowerPlayer SE is an intelligent software player that can automatically
detect and playback all kinds of video/audio files, CD and MP3 files as well. This is
the only software you need for all types of video and audio files. No need to waste
time identifying your file types.
6.2.1 Starting CyberLink PowerPlayer SE
To start CyberLink Power Player, click the Windows Start button, point
to Programs, and then CyberLink PowerPlayer SE, and then click
PowerPlayer.
6.2.2 CyberLink PowerPlayer Control Panel
Minimize
Zoom
Eject
Help
About
Power Off
Stop
Backward Scan
Forward Scan
Step Frame
Backstep Frame
Previous
Next
Play
Stop
Configuration
i-Power!
Increase Volume
CD Mode
Shuffle
Mute
Decrease Volume
Karaoke
Next angle Next audio stream Next subtitle
Add bookmark
Capture frame
Go-Up
Repeat
Menu
Go to bookmark
98
ASUS A7V-M User’s Manual
6. SOFTWARE REFERENCE
6.3 CyberLink PowerDVD
CyberLink PowerDVD is the flagship of CyberLink’s complete range of video and
audio software products. It features unrivaled functions allowing users to view high
quality video and media-rich DVD contents on the personal computer. With the i-
Power Internet Enabling feature, PowerDVD opens DVD enthusiasts to on-line DVD
resources via the PowerDVD Desktop Portal Page.
6.3.1 Starting CyberLink PowerDVD
To start CyberLink PowerDVD, click the Windows Start button, point to
Programs, and then CyberLink PowerDVD, and then click PowerDVD.
6.3.2 CyberLink PowerDVD User Interface
Minimize
Exit
Main Display
Control
Panel
(closed)
Full Screen / CD/File Control
Help Eject
Wheel
Video Window Mode
Functions
ASUS A7V-M User’s Manual
99
6. SOFTWARE REFERENCE
6.4 CyberLink VideoLive Mail
CyberLink’s VideoLive Mail Plus Ver 3.0 (a.k.a. VLM 3) is a convenient and excel-
lent way to create professional quality video mails from PC video/audio input de-
vices and to send the mails to any recipients via VLM 3’s built-in e-mail system
through the Internet. VLM 3’s mails comprise video, sound, or snapshot informa-
tion; and thus may convey the most profound information to target audiences. It is
very convenient for mail recipients who do not need to install additional software
component in order to view VLM 3 mails.
VLM 3 works as a very applicant sales tool. It efficiently delivers profound and live
product information to your target customers without costing a fortune. VLM 3 also
helps corporate managers easily give vivid speeches and broadcast through corpo-
rate E-mail system. For personal or home users, VLM 3 easily records live video
clips allowing users to send them to friends or family members across the Internet.
VLM 3 loads video messages from PC cameras, digital camcorders, analog camcorder
via video capture cards, or from an existing AVI video clips, and captures audio
messages from PC microphones. Video and audio messages are encoded at a very
high compressed rate in a real-time mode. From data input, data conversion, to
sending video mails via Internet, or saving data to disks, the whole procedure is
done in an easy and continuous process.
VLM 3’s video clip compression rate is up to 1:900, and its playback rate is up to 30
frame per second. VLM 3 provides CIF (352 x 288 pixel) display resolution, and
support true color configuration. A one-minute video mail with QCIF (176 x 144)
resolution takes up less than 500KB of memory, making it easy to transmit and save
mail. Users may always adjust resolution and recording parameters for different
purpose.
VLM 3 supports all the hardware devices that are compliant with Video for Win-
dows standard. Video for Windows is a well-accepted and well-tested standard. Thus,
users do not have to worry about compatibility issues.
100
ASUS A7V-M User’s Manual
6. SOFTWARE REFERENCE
6.4.1 Starting VideoLive Mail
To start VideoLive Mail, click the Windows Start button, point to Programs, and
then CyberLink VideoLive Mail, and then click VideoLive Mail x.x. VLM 3’s
Setup Wizard will start and guide you through configuring the video and audio input
peripherals and to setup the e-mail environment.
1. Setup Wizard first will prompt a dialog to confirm that you want to configure
the hardware and E-mail setting. Click Yes to continue the system parameter
configuration.
2. The e-mail configuration screen appears. You will need to enter your name and
the e-mail address. Click Next to continue.
3. The Internet e-mail configuration screen appears. You may choose to use the
VLM 3 built-in E-mail functionality (SMTP mail), or use MAPI compliant e-
mail system. Consult your ISP or MIS staff for the E-mail server IP address if
you are not sure. Click Next to continue.
4. Then the Video Configuration screen shows up. You may have to specify the
video driver for VLM 3, if there are several video-input devices installed. Then
configure the number of video frames to be captured per second. Note that the
more frames you choose, the bigger the file size will be. Click Next to continue.
5. Then the Setup Wizard will then search for the GSM CODECS module for au-
dio compression, and prompt you with the result. Click Next to continue.
6. Setup Wizard then tests the audio volume during playing and recording. Click
Next when ready.
7. Configuration done. Click Finish to complete the environmental setting proce-
dure.
6.4.2 CyberLink VideoLive Mail User Interface
Exit
Minimize
Help
Video Mail Wizard
Start Playback
Save Video File
Snapshot to File
Stop Recording / Playback
Start Recording
Pause
Send Mail
Video Configuration
Load Video File
Send Mail
Increase MIC volume
Decrease MIC volume
Increase speaker volume
Decrease speaker volume
ASUS A7V-M User’s Manual
101
6. SOFTWARE REFERENCE
(This page was intentionally left blank.)
102
ASUS A7V-M User’s Manual
7. APPENDIX
7.1 PCI-L101 Fast Ethernet Card
LAN Activity
Output Signal
Intel
Chipset
RJ45
ASUS
Wake on LAN
Output Signal
Motherboard type
Other
If you are using theASUS PCI-L101 on an ASUS motherboard, leave the jumper on
its defaut setting of “ASUS.” If you are using another brand of motherboard, set the
jumper to “Other.” Connect the Wake on LAN (WOL) output signal to the
motherboard’s WOL_CON in order to utilize the wake on LAN feature of the moth-
erboard. Connect the LAN activity output signal (LAN_LED) to the system cabinet’s
front panel LAN_LED in order to display the LAN data activity.
ASUS A7V-M User’s Manual
103
7. APPENDIX
7.1.1 Features
•
•
•
•
•
•
•
•
•
Intel 82558 Ethernet LAN Controller (Fully integrated 10BASE-T/100BASE-TX)
Wake-On-LAN Remote Control Function Supported
PCI Bus Master Complies to PCI Local Bus Rev. 2.1 specifications
Consists of MAC & PHY (10/100Mbps) interfaces
Complies to IEEE 802.3 10BASE-T and IEEE 802.3u 100BASE-TX interfaces
Fully supports 10BASE-T & 100BASE-TX operations through a single RJ45 port
Supports 32-bit Bus Master Technology / PCI Rev. 2.1
Enhancements on ACPI & APM
Adheres to PCI Bus Power Management Interface Rev. 1.0, ACPI Rev. 1.0, and
Device Class Power Management Rev. 1.0
•
IEEE 802.3u auto-negotiation for 10Mbps/100Mbps Network Data Transfer
Rates.
•
•
Provides LED indicators for monitoring network conditions
Plug and Play
7.1.2 Software Driver Support
•
•
NetWare ODI Drivers - Novell Netware 3.x, 4.x, DOS, OS/2 Client
NDIS 2.01 Drivers - Microsoft LAN Manager, Microsoft Windows 3.11, IBM
LAN Server
•
NDIS 3.0 Drivers - Microsoft Windows NT, Microsoft Windows 95, Microsoft
Windows 3.11
7.1.3 Question and Answer
Q: What is Wake-On-LAN ?
A: The Wake-On-LAN feature provides the capability to remotely power on sys-
tems supporting Wake-On-LAN by simply sending a wake-up frame. With this
feature, remotely uploading/downloading data to/from systems during off-peak
hours will be feasible.
Q: What can Wake-On-LAN do for you ?
A: Wake-On-LAN is a remote management tool with advantages that can reduce
system management workload, provide flexibility to the system administrator’s
job, and then of course save you time-consuming efforts and costs.
Q: What components does Wake-On-LAN require to be enable?
A: To enable Wake-On-LAN function, your system requires Ethernet LAN adapter
card that can activate Wake-On-LAN function, a client with Wake-On-LAN capa-
bility, and software such as LDCM Rev. 3.10 or up that can trigger wake-up frame.
104
ASUS A7V-M User’s Manual
7. APPENDIX
7.2 Glossary
AC97 (Audio Codec '97)
AC '97 is the next step in enabling PCs with audio quality comparable to consumer electronics devices. The specification defines
new cost-effective options to help integrate the components necessary to support next-generation auto-intensive PC applications
such as DVD, 3-D multiplayer gaming and interactive music. The specification also defines new extensions supporting modem
and docking to help both desktop and mobile manufacturers adopt these new technologies more quickly and cost-effectively. This
specification uses software emulation to compete with the PCI SoundBlaster specification.
ACPI (Advanced Configuration and Power Interface)
The ACPI specification defines a cross-platform interface designed to support many operating systems. ACPI defines a flexible
and abstract hardware interface that provides a standard way to integrate power management features throughout a PC system,
including hardware, operating system and application software. This enables the system to automatically turn ON and OFF
peripherals such as CD-ROMs, network cards, hard disk drives, and printers, as well as consumer devices connected to the PC
such as VCRs, TVs, phones, and stereos. With this technology, peripherals will also be able to activate the PC. For example,
inserting a tape into a VCR can turn on the PC, which could then activate a large-screen TV and high-fidelity sound system.
AGP (Accelerated Graphics Port)
An interface specification that enables high-performance 3D graphics on mainstream PCs. AGP was designed to offer the necessary
bandwidth and latency to perform texture mapping directly from system memory.
Bus
PCI
Bus Frequency
33MHz
Bandwidth
33MHz
Data Transfer Rate
133MByte/sec
AGP 1X
AGP 2X
AGP 4X
66MHz
66MHz
66MHz
66MHz
133MHz
266MHz
266MByte/sec
512MByte/sec
1024MByte/sec
BIOS (Basic Input/Output System)
BIOS is a set of routines that affect how the computer transfers data between computer components, such as memory, disks, and
the display adapter. The BIOS instructions are built into the computer’s read-only memory. BIOS parameters can be configured
by the user through the BIOS Setup program. The BIOS can be updated using the provided utility to copy a new BIOS file into the
EEPROM.
Bit (Binary Digit)
Represents the smallest unit of data used by the computer. A bit can have one of two values: 0 or 1.
Boot
Boot means to start the computer operating system by loading it into system memory. When the manual instructs you to “boot” your
system (or computer), it means to turn ON your computer. “Reboot” means to restart your computer. When using Windows 95 or later,
selecting “Restart” from “Start | Shut Down...” will reboot your computer.
Bus Master IDE
PIO (Programmable I/O) IDE requires that the CPU be involved in IDE access and waiting for mechanical events. Bus master
IDE transfers data to/from the memory without interrupting the CPU. Bus master IDE driver and bus master IDE hard disk drives
are required to support bus master IDE mode.
Byte (Binary Term)
One byte is a group of eight contiguous bits. A byte is used to represent a single alphanumeric character, punctuation mark, or
other symbol.
COM Port
COM is a logical device name used by to designate the computer serial ports. Pointing devices, modems, and infrared modules
can be connected to COM ports. Each COM port is configured to use a different IRQ and address assignment.
Concurrent PCI
Concurrent PCI maximizes system performance with simultaneous CPU, PCI and ISA bus activities. It includes multi-transaction
timing, enhanced write performance, a passive release mechanism and support for PCI 2.1 compliant delayed transactions. Concur-
rent PCI provides increased bandwidth, reduced system latencies, improves video and audio performance, and improves processing
of host based applications.
CPU (Central Processing Unit)
The CPU, sometimes called “Processor,” actually functions as the “brain” of the computer. It interprets and executes program
commands and processes data stored in memory. Currently, there are socket 370 (for Pentium III FC-PGA and Celeron-PPGA),
socket 7 (for Pentium, AMD, Cyrix, IBM), slot 1 (for Pentium II and III), slot 2 (for Xeon), and slot A (for AMD) processors.
Device Driver
A device driver is a special set of instructions that allows the computer’s operating system to communicate with devices such as
VGA, audio, printer, or modem.
DOS (Disk Operating System)
DOS is the foundation on which all other programs and software applications operate, including Windows. DOS is responsible
for allocating system resources such as memory, CPU time, disk space, and access to peripheral devices. For this reason, DOS
constitutes the basic interface between you and your computer.
DRAM (Dynamic Random Access Memory)
There are several different types of DRAM such as, EDO DRAM (Extended Data Output DRAM), SDRAM (Synchronous
DRAM), and RDRAM (Rambus DRAM).
Flash ROM
The flash ROM is designed to be a resident program and can be updated by a specific programming method. Normally, the flash ROM
is used for system BIOS which initiates hardware devices and sets up necessary parameters for the OS. Since the contents of flash ROM
can be modified, users are able to update the BIOS by themselves.
ASUS A7V-M User’s Manual
105
7. APPENDIX
IDE (Integrated Drive Electronics)
IDE devices integrate the drive control circuitry directly on the drive itself, eliminating the need for a separate adapter card (in the
case for SCSI devices). UltraDMA/33 IDE devices can achieve up to 33MB/Sec transfer.
LPT Port (Line Printer Port)
Logical device name reserved by DOS for the computer parallel ports. Each LPT port is configured to use a different IRQ and
address assignment.
MMX
A set of 57 new instructions based on a technique called Single Instruction, Multiple Data (SIMD), which is built into the new
Intel Pentium PP/MT (P55C) and Pentium II (Klamath) CPU as well as other x86-compatible microprocessors. The MMX
instructions are designed to accelerate multimedia and communications applications, such as 3D video, 3D sound, video confer-
ence.
PC100
SDRAM is Intel's goal is to ensure that memory subsystems continue to support evolving platform requirements and to assure that
memory does not become a bottleneck to system performance. It is especially important to ensure that the PC memory roadmap
evolves together with the performance roadmaps for the processors, I/O and graphics.
PCI Bus (Peripheral Component Interconnect Local Bus)
PCI bus is a specification that defines a 32-bit data bus interface. PCI is a standard widely used by expansion card manufacturers.
PCI Bus Master
The PCI Bus Master can perform data transfer without local CPU help and furthermore, the CPU can be treated as one of the Bus
Masters. PCI 2.1 supports concurrent PCI operation to allow the local CPU and bus master to work simultaneously.
Plug and Play BIOS
The ISA bus architecture requires the allocation of memory and I/O address, DMA channels and interrupt levels among multiple
ISA cards. However, configuration of ISA cards is typically done with jumpers that change the decode maps for memory and I/O
space and steer the DMA and interrupt signals to different pins on the bus. Further, system configuration files may need to be
updated to reflect these changes. Users typically resolve sharing conflicts by referring to documentation provided by each manu-
facturer. For the average user, this configuration process can be unreliable and frustrating. Plug and play (PnP) BIOS eliminates
the ISAadd-on card hardware conflict problem. The PnPBIOS uses a memory block to define and remember each card's configu-
ration, which allows the user to change the card's IRQs and DMA in BIOS either automatically or manually.
POST (Power On Self Test)
When you turn ON the computer, it will first run through the POST, a series of software-controlled diagnostic tests. The POST
checks system memory, the motherboard circuitry, the display, the keyboard, the diskette drive, and other I/O devices.
PS/2 Port
PS/2 ports are based on IBM Micro Channel Architecture. This type of architecture transfers data through a 16-bit or 32-bit bus.
A PS/2 mouse and/or keyboard may be used on ATX motherboards.
ROM (Read Only Memory)
ROM is nonvolatile memory used to store permanent programs (called firmware) used in certain computer components. Flash
ROM (or EEPROM) can be reprogrammed with new programs (or BIOS).
SCSI (Small Computer System Interface)
High speed multi-threaded I/O interface defined by the X3T9.2 committee of the American National Standards Institute (ANSI)
for connecting many peripheral devices. The standard started from 10MBytes/sec to 160MBytes/sec available today.
SDRAM (Synchronous DRAM)
The SDRAM features a fully synchronous operation referenced to a positive edge clock whereby all operations are synchronized
at a clock input which enables the coexistence of high performance and a simple user interface. SDRAM takes memory access
away from the CPU's control; internal registers in the chips accept the request, and let the CPU do something else while the data
requested is assembled for the next time the CPU talks to the memory. As they work on their own clock cycle, the rest of the
system can be clocked faster. There is a version optimized for video cards, and main memory for motherboards.
SPD for SDRAM module
Serial Presence Detect (SPD) is most like an ID detect for SDRAM module, it using an EEPROM component on DIMM module
for storing module configuration information inside. The Serial Presence Detect function is implemented using a 2048 bit EEPROM
component. This nonvolatile storage device contains data programmed by the DIMM manufacturer that identifies the module
type and various SDRAM organization and timing parameters.
System Disk
A system disk contains the core file of an operating system and is used to boot up the operating system.
UltraDMA
Ultra DMA/33 is a "synchronous DMA" protocol designed by Intel. This function is included into Intel's PIIX4 chipset. The
traditional IDE transfer only uses one edge of the data stroke as the data transfer. Ultra DMA/33 uses both edges of data strobe
when the data is transferred. Hence, the data transfer rate is double of the PIO mode 4 or DMA mode 2 (16.6MB/s x2 = 33MB/s)
on ATA-2 devices.
Ultra ATA/66, also known as Ultra DMA/66, is an extension of current Ultra ATA/33 interface. This high-speed interface has
doubled the Ultra ATA/33 burst data transfer rate to 66.6 Mbytes/sec and maximized disk performance under current PCI local
bus environment
USB (Universal Serial Bus)
A 4-pin serial cable bus that allows up to 127 plug and play computer peripherals such as keyboard, mouse, joystick, scanner,
printer, modem, and monitor to share a bandwidth through a host scheduled token based protocol. This allows attaching or
detaching while the host and other peripherals are in operation. Supports synchronous and asynchronous transfer types over the
same set of wires up to 12Mbit/sec. USB 2.0 provides twice the transfer rate compared to USB 1.0 and competes with the 1394
standard.
Wake-On-LAN
Computer will automatically wake-up upon receiving a wake-up packet through a Network interface when it is under power soft-
off, suspend or sleep mode.
106
ASUS A7V-M User’s Manual
|