TravelMate 4060 Series
Service Guide
Service guide files and updates are available
on the ACER/CSD web; for more information,
please refer to http://csd.acer.com.tw
PRINTED IN TAIWAN
Copyright
Copyright © 2005 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in
any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without
the prior written permission of Acer Incorporated.
Disclaimer
The information in this guide is subject to change without notice.
Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular
purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the
programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its
dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software.
Acer is a registered trademark of Acer Corporation.
Intel is a registered trademark of Intel Corporation.
Pentium and Pentium II/III are trademarks of Intel Corporation.
Other brand and product names are trademarks and/or registered trademarks of their respective holders.
III
Conventions
The following conventions are used in this manual:
SCREEN MESSAGES
Denotes actual messages that appear
on screen.
NOTE
Gives bits and pieces of additional
information related to the current
topic.
WARNING
CAUTION
Alerts you to any damage that might
result from doing or not doing specific
actions.
Gives precautionary measures to
avoid possible hardware or software
problems.
IMPORTANT
Reminds you to do specific actions
relevant to the accomplishment of
procedures.
IV
Preface
Before using this information and the product it supports, please read the following general information.
1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION
decided for Acer's "global" product offering. To better fit local market requirements and enhance product
competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g.
add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered
in this generic service guide. In such cases, please contact your regional offices or the responsible
personnel/channel to provide you with further technical details.
2. Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information
available on your regional web or channel. If, for whatever reason, a part number change is made, it will
not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer
office may have a DIFFERENT part number code to those given in the FRU list of this printed Service
Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and
service of customer machines.
V
VI
Table of Contents
Chapter 1 System Introduction 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Closed front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Left view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Right view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Rear view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Bottom view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Easy-Launch Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Using the keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Lock keys and embedded numeric keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Windows keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Hot Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Special keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Touchpad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Touchpad basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Hardware Specifications and Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Chapter 2 System Utilities
28
BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Navigating the BIOS Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Main . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
BIOS Flash Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Create Crisis Recovery Diskette . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Recover BIOS from Crisis Recovery Diskette . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Chapter 3 Machine Disassembly and Replacement
42
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Disassembly Procedure Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Removing the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Removing the HDD Module/the Memory and the Wireless LAN Card/
the Thermal Module and the CPU/ODD Module and LCD Module . . . . . . . . . . . . . .47
Removing the HDD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Removing the Memory and the Wireless LAN Card . . . . . . . . . . . . . . . . . . . . . .47
Removing the Thermal Module and CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Removing the ODD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Removing the LCD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Disassembling the Main Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Separate the Main Unit Into the Upper and the Lower Case Assembly . . . . . . .51
Disassembling the Upper Case Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Disassembling the Lower Case Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
VII
Table of Contents
Disassembling the LCD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Disassembling the External Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Disassembling the HDD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Disassembling the Optical Drive Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Chapter 4 Troubleshooting
58
System Check Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
External Diskette Drive Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
External CD-ROM Drive Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Keyboard or Auxiliary Input Device Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Memory check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Power System Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Touchpad Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Power-On Self-Test (POST) Error Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Index of Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Phoenix BIOS Beep Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Index of Symptom-to-FRU Error Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Intermittent Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Undetermined Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Chapter 6 FRU (Field Replaceable Unit) List
76
TravelMate 4060 Exploded Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Please notice that Chapter 5 has been combined to Chapter 1.
VIII
IX
Chapter 1
System Introduction
Features
This computer was designed with the user in mind. Here are just a few of its many features:
Platform
®
®
T
Intel Pentium M 730/740/750/760/770/780 processor (2MB L2 cache, 1.60/1.73/1.86/2/2.13/
2.26 GHz, 533 MHz FSB)
®
®
T
T
Intel Pentium M 725 processor (2MB L2 Cache, 1.60 GHz, 400 MHz FSB)
Intel Celeron M processor 360/370/380 (1 MB L2 cache, 1.40/1.50/1.60 GHz, 400 MHz FSB)
®
T
Chipset: Intel 915GM
Memory
T
256 MB/512 MB of DDRII 533 memory, upgradeable to 2 GB with dual so DIMM modules
Data storage
T
40/60/80/100 GB ATA/100 hard disk
DVD-Dual double-layer drive
DVD/CD-RW combo drive
T
T
Display and graphics
Color Thin-Film Transistor (TFT) LCD displaying at
T
-- 15” XGA (1024 X 768)
-- 15.4” WXGA (1280 X 800) supporting simultaneous multi-window viewing on dual displays via
Acer GridVista
®
T
Intel 915GM integrated 3D graphics, featuring Intel Graphics Media Accelerator 900 and up to
128 MB of shared memory
®
®
T
T
T
Microsoft DirectX 7.0 and dual independent display support
MPEG-2/DVD hardware-assisted capability
Simultaneous LCD and CRT display with LCD panel resolution at 70 Hz
Communication
T
Modem: 56K ITU V.92 modem with PTT approval; Wake-on-Ring ready
T
LAN: 10/100 Mbps Fast Ethernet; Wake-on-LAN ready
TM
T
Wireless LAN (optional): integrated miniPCI Acer InviLink 802.11b/g Wi-Fi CERTIFIEDTM
solution
T
T
Acer SignalUP wireless technology support
®
Wireless PAN (optional): integrated Bluetooth
Audio
T
Audio system with two built-in speakers
T
T
Sound Blaster ProTM and MS-Sound compatible
Built-in microphone
Chapter 1
1
Input devices
T
T
T
88-/89-key Acer FineTouchTM keyboard
Touchpad with 4-way integrated scroll button
Four easy-launch buttons
®
T
Two front-panel buttons: wireless LED-button and Bluetooth LED-button
I/O interface
T
Three USB 2.0 ports
Ethernet (RJ-45) port
Modem (RJ-11) port
External display (VGA) port
Microphone
T
T
T
T
T
T
T
T
Line-in jack
Headphones/speaker/line-out port
One Type II PC Card slot
DC-in jack for AC adaptor
2
TravelMate 4060
System Block Diagram
Chapter 1
3
Board Layout
Top View
4
TravelMate 4060
Bottom View
1
SW1
CN2
CN7
CN5
U17
Lid Switch
2
CN1
CN3
CN4
CN6
U4
LCD Connector
3
Launch Board Connector
Keyboard Connector
Touchpad Board Connector
Clock Generator
4
Modem Connector
5
6
Bluetooth Module Connector
Internal Microphone Connector
PCMCIA Connector
7
8
9
10
12
14
16
18
20
11
13
15
17
19
CN9
CN13
CN14
CN17
U11
MDC Connector
CN11
CN12
CN15
CN26
U13
Internal Speaker Connector
CRT Connector
Power Jack
Battery Connector
RJ45 & RJ11 Connector
North Bridge
Optical Disk Drive Connector
Wireless LAN Controller
CPU Socket
Chapter 1
5
21
23
CN20
U19
USB Connector
BIOS ROM
22
24
CN21
U4
USB Connector
EC PC97551 (Power and I/O
Connector)
25
27
29
31
33
35
37
39
41
CN22
U1
RTC Battery
26
28
30
32
34
36
38
40
CN18
CN19
CN24
CN27
CN29
SW3
Memory Socket 1
Memory Socket 2
PCMCIA Connector
USB Connector
Microphone Jack
WLAN Button
LAN Chipset RTL8100CL
South Bridge
U18
CN25
CN28
CN30
SW2
LED1
U10
HDD Connector
Line-out/SPEDIF Jack
Line-in Jack
Bluetooth Button
Power LED
LED2
U22
Charger LED
Audio Codec
Fan Connector
6
TravelMate 4060
Panel
This is a brief introduction to the I/O ports, the features and the indicators.
Front view
#
Item
Description
1
Display screen
Also called LCD (Liquid Crystal Display), displays computer
output.
2
3
4
Microphone
Keyboard
Palmrest
Internal microphone for sound recording.
For entering data into you computer.
Comfortable support area for your hands when you use the
computer.
5
Click buttons (Left, center and right)
The left and right buttons function like the left and right
mouse buttons; the center button serves as a 4-way scroll
button.
6
7
Touchpad
Touch-sensitive pointing device which functions like a
computer mouse.
Status indicators
LEDs (Light Emitting Diodes) that turn on and off to show
the status of the computer and its functions and
components.
8
9
Easy-Launch buttons
Power button
Buttons for launching frequently used programs.
Turns the computer on and off.
Chapter 1
7
Closed front view
#
Icon
Item/ Port
Description
1
2
Speakers
Left and right speakers deliver stereo audio
output.
Power indicator
Battery indicator
Lights up when the computer is on.
3
Lights up when the battery is being charged.
4
5
Bluetooth communication button/
indicator
Press to enable/disable the Bluetooth function.
Indicates the status of Bluetooth communication
(optional).
Wireless communication button/
indicator
Press to enable/disable the wireless function.
Indicates the status of wireless LAN
communication (optional).
6
7
Line-in jack
Accepts audio line-in devices (e.g., audio CD
player, stereo walkman).
Microphone jack
Accepts inputs from external microphones.
8
9
Speaker/Line-Out/Headphone jack
USB 2.0 port
Connects to audio line-out devices (e.g.,
speakers, headphones).
Connects to Universal Serial Bus (USB) 2.0
devices (e.g., USB mouse, UsB camera).
Left view
8
TravelMate 4060
#
Icon
Item/ Port
Description
1
Optical drive
LED indicator
Internal optical drive; accepts CDs or DVDs
depending on the optical drive type.
2
3
4
Lights up when the optical drive is active.
Ejects the optical drive tray from the drive.
Optical drive eject button
Emergency eject hole
Ejects the optical drive tray when the computer is
turned off.
Right view
#
Icon
Item/ Port
Description
1
2
PC Card slot eject button Ejects the PC Card from the slot
PC card slot
Accepts one Type II CardBus PC Card.
3
4
Two USB 2.0 ports
Network jack
Connects to Universal Serial Bus (USB) 2.0
devices (e.g., USB mouse, USB camera).
Connects to an Ethernet 10/100 based
network.
5
Modem jack
Connects to a phone line.
6
Ventilation slots
Enable the computer to stay cool, even after
prolonged use.
Rear view
Chapter 1
9
#
Icon
Port
Power jack
Description
1
2
Connects to an AC adaptor.
External display port
Security keylock
Connects to a display device (e.g., external
monitor, LCD projector).
3
Connects to a Kensington-compatible
computer security lock.
Bottom view
#
Item
Description
1
2
3
4
5
Hard disc bay
Houses the computer’s hard disc (secured by a screw).
Unlatches the battery to remove the battery pack.
Houses the computer’s battery pack.
Battery release latch
Battery bay
Battery lock
Locks the battery in place.
Cooling fan
Helps keep the computer cool.
Note: Do not cover or obstruct the opening of the fan.
6
Memory comparment
House the computer’s main memory.
10
TravelMate 4060
Indicators
The computer has three easy-to-read status icons on the upper-right above the keyboard, and four on the front
panel.
Icon
Function
Caps Lock
Description
Lights when Caps Lock is activated.
Num Lock
Lights when Numeric Lock is activated.
Media activity
Indicates when the hard disk or optical
drive is active.
Power
Lights when the computer is on.
Battery
Lights when the battery is being charged.
Bluetooth
Indicates the status of Bluetooth
communication.
Wireless LAN
Indicates the status of Bluetooth
communication.
NOTE: 1. Charging: the light shows amber when the battery is charging.
NOTE: 2. Fully charged: light shows green when in AC mode.
Chapter 1
11
Easy-Launch Buttons
Located at the upper-right, above the keyboard are four buttons. These buttons are called launch keys. They
are mail, Web browser, Acer Empowering key “
“, and one user-programmable button.
Press “ “ to run the Acer eManager. The mail and Web buttons are pre-set ot email and internet programs,
but can be reset by users. To set the Web browser, mail and programmable keys, run the Acer Launch
Manager.
Launch key
Default application
User-programmable
P
Acer eManager (user-programmable)
Web browser
Mail
Internet browser (user-programmable)
Email application (user-programmable)
12
TravelMate 4060
Using the keyboard
The keyboard has full-sized keys and an embedded keypad, separate cursor keys, two Windows keys and
twelve function keys.
Lock keys and embedded numeric keypad
The keyboard has three lock keys which you can toggle on and off.
Lock key
Description
Caps Lock
When @is on, all alphabetic characters typed are in uppercase.
@
Num Lock <Fn>+<F11>
When ]is on, the embedded keypad is in numeric mode. The keys function
as a calculator (complete with the arithmetic operators ), -, *, and /). Use this mode
when you need to do a lot of numeric data entry. A better solution would be to
connect an external keypad.
]
Scroll Lock <Fn>+<F12>
When [is on, the screen moves one line up or down when you press the up
[
or down arrow keys respectively. [does not work with some applications.
The embedded numeric keypad functions like a desktop numeric keypad. It is indicated by small characters
located on the upper right corner of the keycaps. To simplify the keyboard legend, cursor-control key symbols
are not printed on the keys.
Desired access
Num lock on
Num lock off
Number keys on embedded
keypad
Type numbers in a normal manner.
Cursor-control keys on embedded Hold <Shift> while using cursor-control
Hold <Fn> while using cursor-
control keys.
keypad
keys.
Main keyboard keys
Hold <Fn> while typing letters on embedded Type the letters in a normal manner.
keypad.
Windows keys
The keyboard has two keys that perform Windows-specific functions.
Chapter 1
13
Keys
Windows logo key
Description
Start button. Combinations with this key perform shortcut functions. Below
are a few examples:
+ <Tab> (Activates the next Taskbar button)
+ <E> (Opens the My Computer window)
+ <F1> (Opens Help and Support)
+ <F> (Opens the Find: All Files dialog box)
+ <R> (Opens the Run dialog box)
+ <M> (Minimizes all windows)
<shift>+
+< M> (Undoes the minimize all windows)
Application key
This key has the same effect as clicking the right mouse button; it opens the
application’s context menu.
Hot Keys
The computer employs hot keys or key combinations to access most of the computer’s controls like screen
contrast and brightness, volume output and the BIOS Utility.
To activate hot keys, press and hold the <Fn> key before pressing the other key in the hot key combination.
Hot Key
Icon
Function
Hotkey help
Description
Displays a list of the hotkeys and their functions.
Fn-
l
Acer eSetting
Launches Acer eSetting in the eManager set by the
Acer Empowering key..
Fn-
m
14
TravelMate 4060
Hot Key
Icon
Function
Description
Launches Power options.
Power Management
Fn-
n
Sleep
Puts the computer in Sleep mode.
Fn-
o
Display toggle
Switches display output between the display screen,
external monitor (if connected) and both the display
screen and external monitor.
Fn-
p
Screen blank
Turns the display screen backlight off to save power.
Press any key to return.
Fn-
q
Touchpad Toggle
Speaker toggle
Turns the internal touchpad on and off.
Turns the speakers on and off.
Fn-
r
Fn-
s
Volume up
Increases the sound volume.
Decreases the sound volume.
Fn-
w
Volume down
Fn-
y
Brightness up
Increases the screen brightness.
Decreases the screen brightness.
Fn-
x
Brightness down
Fn-
¨
z
Special keys
You can locate the Euro symbol at the upper-center (for European keyboard) and/or bottom-right (Chinese
keyboard) of your keyboard. To type:
Chapter 1
15
The Euro symbol
1. Open a text editor or word processor.
2. Either directly press the <Euro> key at the bottom-right of the keyboard (for Chinese keyboard), or hold
<Alt Gr> and then press the <5> key at the upper-center of the keyboard.symbol at the upper-center of
the keyboard (for European keyboard, you can use both method).
typography/faq/faq12.htm for more information.
The US dollar sign
1. Open a text editor or word processor.
2. Either directly press the <Euro> key at the bottom-right of the keyboard (for Chinese keyboard), or hold
<Shift> and then press the <4> key at the upper-center of the keyboard.symbol at the upper-center of the
keyboard (for European keyboard, you can use both method).
NOTE: This function varies according to the language settings.
16
TravelMate 4060
Touchpad
The built-in touchpad is a pointing device that senses movement on its surface. This means the cursor
responds as you move your finger on the surface of the touchpad. The central location on the palmrest
provides optimum comfort and suuport.
Touchpad basics
The following items teach you how to use the touchpad:
* Move your finger across the touchpad (2) to move the cursor.
* Press the left (1) and right (4) buttons located on the edge of the touchpad to do selection and execution
functions. These two buttons are similar to the left and right buttons on a mouse. Tapping on the touchapd is
the same as clicking the left button.
* Use the 4-way scroll (3) button to scroll up or down and move left or right a page. This button mimics your
cursor pressing on the right scroll bar of Windows applications.
Function
Execute
Left button (1)
Right button (4)
Touchpad (2)
Center button (3)
Click twice quickly.
Tap twice (at the same speed
as double-clicking a mouse
button).
Select
Drag
Click once.
Tap once.
Click and hold,
then use finger to
drag the cursor on
the touchpad.
Tap twice (at the same speed
as double-clicking a mouse
button); hold finger to the
touchpad on the second tap
and drag the cursor.
Access
Click once.
context menu
Scroll
Click and hold to
move up/down/left/
right.
NOTE: Keep your fingers dry and clean when using the touchpad. Also keep the touchpad dry and clean. The
touchpad is sensitive to finger movement, hence, the lighter the touch, the better the response. Taping
harder will not increase the touchpad’s responsiveness.
Chapter 1
17
Hardware Specifications and Configurations
System Board Major Chip
Item
Controller
System core logic
Memory controller
Audio controller
®
Intel 915GM+ICH6-M
®
Integrated in Intel 915GM
RealTek ALC260 HD audio interface
(Audio amplifer: Maxiam MAX9755)
PCMCIA controller for socket
Video controller
TI PCI1510A
®
built-in Intel 915GM
Power and Keyboard controller
Wireless controller (mini PCI)
KBC NS97551
Intel (The controller is on the Wireless LAN card. Please look at the
wireless LAN card for controller details).
Processor
Item
Specification
CPU type
®
®
Intel Pentium M 730/740/750/760/770/780 processor (2MB L2 cache,
1.60/1.73/1.86/2/2.13/2.26 GHz, 533 MHz FSB)
®
®
Intel Pentium M 725 processor (2MB L2 Cache, 1.60 GHz, 400 MHz FSB)
®
®
Intel Celeron M processor 360/370/380 (1 MB L2 cache, 1.40/1.50/1.60
GHz, 400 MHz FSB)
CPU package
Intel socketable 478 pins Micro-FCPGA
CPU core voltage
Low speed: 0.8V
High speed: 1.5V
CPU I/O voltage
1.2V
BIOS
Item
BIOS vendor
Specification
Pheonix BIOS
BIOS Version
BIOS ROM type
BIOS ROM size
BIOS package
Flash ROM, SST39VF040
512Kbyte
32 Pin PLCC-lead
Supported protocols
ACPI 2.0 (if available, at least 1.0b), SMBIOS 2.3, PCI 2.2, Boot Block,
PXE 2.0, Mobile PC2001, Hard Disk Password, INT 13h Extensions, PCI
Bus Power Management interface Specification, EI Torito-Bootable CD-
ROM Format Specification V1.0, Simple Boot Flag 1.0
Second Level Cache
Item
Cache controller
Cache size
Specification
Built-in CPU
®
®
2MB for Intel Pentium M processor
®
®
1MB for Intel Celeron M processor
Always Enabled
1st level cache control
2nd level cache control
Always Enabled
18
TravelMate 4060
Second Level Cache
Item
Specification
Specification
Cache scheme control
Fixed-in write back
System Memory
Item
Memory controller
built-in CPU
Onboard memory size
0MB
DIMM socket number
2 Sockets
Supports memory size per socket
Supports maximum memory size
Supports DIMM type
256MB(min)/1024MB(max)
2GB with 2 SODIMM support
DDRII
Supports DIMM Speed
Supports DIMM voltage
Supports DIMM package
Memory module combinations
533MHz
1.8 V/0.9V
200-pin so-DIMM
You can install memory modules in any combinations as long as they
match the above specifications .
Memory Combinations
Slot 1
Slot 2
Total Memory
0MB
256MB
512MB
1024MB
0MB
256MB
512MB
1024MB
256MB
512MB
768MB
1280MB
512MB
768MB
1024MB
1536MB
1024MB
1280MB
1536MB
0MB
0MB
256MB
256MB
256MB
512MB
1024MB
0MB
256MB
256MB
512MB
512MB
256MB
512MB
1024MB
0MB
512MB
512MB
1024MB
1024MB
1024MB
1024MB
256MB
512MB
1024MB
2048MB (2G)
Above table lists some system memory configurations. You may combine DIMMs with various capacities to
form other combinations.
LAN Interface
Item
Specification
Chipset
RealTek 8100CL
10/100
Supports LAN protocol
LAN connector type
RJ45
LAN connector location
Right side
Chapter 1
19
Modem Interface
Item
Specification
Chipset
CS1037 Internal Agere Scorpio chipset (Scorpio+CSP1037B)
Fax modem data baud rate (bps)
Data modem data baud rate (bps)
Supports modem protocol
Modem connector type
14.4K
56K
V.92MDC
RJ11
Modem connector location
Right side
Wireless Module 802.11b/g (optional device)
Item
Specification
Chipset
Data throughput
Protocol
11M~54M bps
802.11 b+g
Interface
Mini-PCI type II
Floppy Disk Drive Interface
Item
Specification
Vendor & model name
Floppy Disk Specifications
Media recognition
Sectors/track
There is no FDD module for this product
2DD (720KB)
2HD (1.2 MB, 3 mode)
2HD (1.44MB)
9
15
18
Tracks
80
80
80
Data transfer rate
(Kbit/s)
1 MB
1.6 MB
2 MB
Rotational speed (RPM)
Read/write heads
Encoding method
Power Requirement
Input Voltage (V)
300
2
360
300
MFM
+5V
.
Hard Disk Drive Interface
Item
Vendor & Model
Name
HGST MORAGA
IC25N060ATMR04-0
HGST MORAGA
IC25N080ATMR04-0 08K635 MK1031GAS
TOSHIBA PLUTO
08K0634
Seagate N2 ST9808210A
SEAGATE N2 ST9100822A
Seagate N2 ST960821A
TOSHIBA PLUTO
MK6025GAS
TOSHIBA PLUTO
MK6025GAS
Capacity (MB)
Bytes per sector
Logical heads
Logical sectors
Drive Format
60000
512
16
80000
512
16
100000
512
16
63
63
63
Logical cylinders
16383
16383
16383
20
TravelMate 4060
Hard Disk Drive Interface
Item
Physical read/write
heads
3/3/4
4/3/2
4
Disks
2/2/4
2/2/4
2
Spindle speed (RPM) 4200RPM
Performance Specifications
4200RPM
4200RPM
Buffer size
Interface
8MBytes (8192kbytes)
8MBytes (8192kbytes)
ATA/ATAPI-6
8MBytes
ATA-6
ATA/ATAPI-6
100 MB/Sec
Data transfer, rate
(host~buffer, Mbytes/
s)
100 MB/Sec
100 MB/Sec
DC Power Requirements
Voltage tolerance
5 +/- 5%
5 +/- 5%
5 +/- 5%
Remark
Combo Drive Interface
Item
Vendor & model name
General Specification
Interface
Specification
DVD/CDRW TOSHIBA TS-L462A
Enhanced IDE (ATAPI)
8cm/12cm
Disc Diameter
Loading Type
Drawer Type
Drive Mounting
Read/Write
Horizontal/Vertical
Read Speed:
Max. 24X(3,600 KB/sec) for CD-ROM CAV 24X
Max. 24X(3,600 KB/sec) for CD-RW
Write Speed:
CAV 24X
Max. 24X(3,600 KB/sec) for CD-R
Max. 10X(1,500 KB/sec) for CD-RW
Max. 24X(3,600 KB/sec) for US-RW
P-CAV 24X/20X/16X ; CLV 10X/8X/4X
CLV 10X/4X
P-CAV 24X/16X
Mounting Orientation
Buffer Under Run
Power consumption
Interface
Horizontal/Vertical
2MB
All angles
DC +5v/1.2A
Enhanced IDE(ATAPI) compatible
Media compatibility
CD:
120mm CD-ROM (Read Only)
80mm CD
800/700/650/550MB CD-Recordable (Read & Write)
700/650MB CD-Rewritable (Read & Write)
700/650MB High Speed CD-Rewritable (Read & Write)
DVD:
5/9/10/18 DVD-Single/Dual (PTP, OTP)
3.9/4.7G DVD-R (Read Only)
4.7GDVD+R (Read Only)
DVD±RW (Read only)
80mm DVD
Chapter 1
21
Combo Drive Interface
Item
Specification
Remark
Format compatibility
CD
CD-DA (Red Book) - Standard Audio CD & CD-TEXT
CD-ROM (Yellow Book Mode1 & 2) - Standard Data
CD-ROM XA (Mode2 Form1 & 2) - Photo CD, Multi-Session
CD-I /FMV (Green Book, Mode2 Form1 & 2, Ready, Bridge)
CD-Extra/ CD-Plus (Blue Book) - Audio & Text/Video
Video-CD (White Book) - MPEG1 Video
DVD
DVD-ROM (Book 1.02),
DVD-Video (Book 1.1)
DVD-R (Book 1.0, 3.9G)
DVD-R (Book 2.0, 4.7G) - General & Authoring
DVD+R (Version 1.0)
DVD±RW
Play DVD-AUDIO except the case that required CPPM
(Content protection for prerecorded Media)
Write Method
Loading mechanism
Load: Manual
Release: (a) Electrical Release
(Release Button)
(b) Release by ATAPI
command
(c) Emergency Release
Power Requirement
Input Voltage
DC +5V+/- 5% (operation)
DC +5V+/- 8% (start up)
DVD-RW Interface
Item
Specification
Vendor & model name
Performance Specification
TOSHIBA TS-L532A
Transfer rate (KB/sec)
(1) Read DVD-ROM
DVD-R
MAX 8X CAV (MAX 10800kB/s)
MAX 4X CAV (MAX 5400kB/s)
MAX 24X CAV (MAX 3600kB/s)
4X, 8X (CLV), MAX. 24X(ZCLV)
CD-ROM
(2) Write CD-R
CD-RW
4X
(CLV)
HS-RW
4X, 8X, 10X (CLV)
US-RW
8X, 10X(CLV), MAX. 16X (ZCLV)
(3) ATAPI Interface
PIO mode
16.6MB/s: PIO mode4
DMA mode
16.6MB/s: Multi word mode2
33.3MB/s: Ultra DMA mode2
Ultra DMA mode
Buffer Memory
Interface
2MB
Enhanced IDE(ATAPI) compatible
Applicable disc format
Read:
copy-protected DVD discs, CD-ROM, CD audio, DVD-ROM and DVD-RAM,
DVD-R/-RW, DVD+R/+RW and CD-R/-RW, DVD-ROM, DVD-R/+R, DVD-R/+R,
DVD-RW/+RW, 4.38GB DVD-RAM, CD-DA discs, CD-ROM discs, CD-R discs,
CD-RW discs
Write:
CD-R, CD-RW, high-speed CD-RW, Ultra-speed CD-RW, DVD-R, DVD-RW,
DVD+R, DVD+RW
22
TravelMate 4060
DVD-RW Interface
Item
Specification
Loading mechanism
Load: Manual
Release: (a) Electrical Release (Release Button)
(b) Release by ATAPI command
(c) Emergency Release
Power Requirement
Input Voltage
5 V +/- 5 % (Operating)
Audio Interface
Item
Audio Controller
Specification
Realtek ALC260 (Audio amplifier: Maxim MAX9755)
Audio onboard or optional
Mono or Stereo
Built-in
Stereo
Resolution
18 bit stereo full duplex
Compatibility
HD audio Interface; S/PDIF output for PCM or AC-3 content
Sampling rate
1Hz resolution VSR (Variable Sampling Rate)
Internal microphone
Internal speaker / Quantity
Supports PnP DMA channel
Yes
Yes
DMA channel 0
DMA channel 1
Supports PnP IRQ
IRQ10, IRQ11
Video Interface
Item
Specification
Vendor & Model Name
®
built-in Intel 915GM
Video memory size
up to 128MB for Aspire 3000/5000
up to 64MB for Aspire 3500
Chip voltage
Core / 2.5V, 1.5V,
Supports ZV (Zoomed Video) port
Graph interface
NO
4X AGP (Accelerated Graphic Port) Bus
1600X1200 (UXGA)
2048X1536@60HZ
Maximum resolution LCD
Maximum resolution CRT
Video Resolutions Mode
Monitor Resolution
2D Display Mode
640x480
Hz
120
800x600
120
120
120
120
85
1024x768
1152X864
1280X1024
1600x1200
1920x1080*16:9
1920x1200
75
75
1920x1440
75
Chapter 1
23
Video Resolutions Mode
Monitor Resolution
Hz
2048x1536
60
Resolution, colors and maximum refersh rate (Hz) in 256, 65K or 16.7M colors.
NOTE: 16:9 aspect ratio monitors are supported on 1920x1080 and 848x480 on Windows(R)XP, Windows(R)
2000 and Windows(R)ME. The complete list of resolutions depends on the driver version and operating
system. NOTE: resolutions are limited by the performance of the attached monitor.
USB Port
Item
USB Compliancy Level
Specification
2.0
OHCI
USB 2.0
3
Number of USB port
Location
Two on the right side; one on the front side
Enable/Disable by BIOS Setup
Serial port function control
PCMCIA Port
Item
PCMCIA controller
Specification
TI PCI1510A
Supports card type
Type II (No Tpye III)
One type II
Right side
Number of slots
Access location
Supports ZV (Zoomed Video) port
Supports 32 bit CardBus
NO
Yes (IRQ17)
Keyboard
Item
Keyboard controller
Specification
KBC NS97551
Keyboard vendor
Darfon
88-/89-key
Yes
Total number of keypads
Windows keys
Internal & external keyboard work simultaneously
Yes
Battery
Item
Specification
Vendor & model name
SANYO
PANASONIC
PANASONIC (RoHS)
SANYO LI-ION 4UR18650F-2-QC141
SIMPPLO
SONY
Battery Type
Lithium-ION
4400mAH
14.8V
Pack capacity
Nominal voltage
Number of battery cell
8
24
TravelMate 4060
Battery
Item
Specification
4S2P for Sanyo and Panasonic
Package configuration
4S1P for Sanyo QC141,SIMPPLO and SONY
41.8V / 9.6V
Package voltage
LCD
Item
Vendor & model name
Screen Diagonal (mm)
Active Area (mm)
Display resolution (pixels)
Pixel Pitch
Specification
AU B154EW01-08
QDI QD15TL02-03
15.4inch
15.4inch
331.2(H)x207.0(V)
WXGA (1280x800)
0.2588(H)x0.2588(H)mm
RGB vertical stripe
Normally white
Not show
331.2(H)x207.0(V)
WXGA (1280x800)
0.2588(H)x0.2588(H)mm
RGB vertical stripe
Normally white
Pixel Arrangement
Display Mode
Surface Treatment
glossy, hardness 2H
160
Typical White Luminance (cd/m2)
also called Brightness
180
Luminance Uniformity
Contrast Ratio
not show
400
1.4(max)
400
Response Time (Optical Rise Time/Fall
Time)msec
16
25(5ms for rise+20 ms for
decay)
Nominal Input Voltage VDD
Typical Power Consumption (watt)
Weight
not show
not show
6.5 (max)
4.38 (for lamp)
585
585
Physical Size(mm)
Support Color
344(W)x222(H)x6.5(D)
Native 262K colours
344(W)x222(H)x6.5(D)
262K colours
Viewing Angle (degree)
Horizontal: Right/Left
Vertial: Upper/Lower
40/40
10/30
45/45
15/35
Temperature Range(° C)
0 to 50
0 to 50
Operating
-20 to 60
-20 to 60
Storage (shipping)
AC Adapter
Item
Specification
Vendor & model name
LITE-ON PA-1650-02QR
LI SHIN SLS0335A19A57LF
DELTA SADP-65KB
Input Requirements
Maximum input AC current
Inrush currenct
3.42A
50A @ 115Vac
100A @ 230Vac
Nominal frequency (Hz)
Frequency variation range (Hz)
Input voltage range (Vrms)
Inrush current
50-60
47-63
90V AC-264V AC
The maximum inrush current will be less than 50A and 100A when the adapter
is connected to 115Vac and 230Vac respectively.
Chapter 1
25
AC Adapter
Item
Specification
Efficiency
It should provide an efficiency of 83% minimum, when measured at maximum
load under 115Vac.
Output Ratings (CV mode)
DC output voltage
19V
Noise + Ripple
300mVp-pmax (20 MHz bandwidth)
0(min) 3.16A(max)
Load
Output Ratings (CC mode)
DC output voltage
19V +/-1.0V for CV mode
3.6 +/- 0.3A
Constant current mode
Dynamic Output Characteristics
Turn-on delay time
3 sec (@ 115Vac)
Hold up time
5ms (@115Vac, Full load)
Over Voltage Protection (OVP)
Short circuit protection
Electrostatic discharge (ESD)
24V
3.9A max can be protected and output can be shorted without damage
15KV (at air discharge)
8KV (at contact discharge)
Dielectric Withstand Voltage
Primary to secondary
Leakage current
3000Vac
0.25 mA max. (@ 254Vac, 60Hz)
Safety Requirements:
Regulatory Requirements
1.The subject product rated 100-120V 60Hz must be listed under UL 1950 and
certified with SCA Standard C22.2 No.950.
2.The subject product rated 200-240V 50Hz must comply with low voltage
directive 73/23EEC.
EMI Requirements:
1.The subject product rated 100-120V 60Hz must meet the EMI requirements
of FCC part 15, Subpart B for Class B Digital Device and get FCC Certification
before marketing into USA and Canada.
2.The subject product rated 200-240V 50Hz must meet the EMC Directive 89/
336/EEC.
3.The subject product rated 100-120V must meet the VCCI-2 EMI
requirements.
Power Management
ACPI Mode
Mech. Off (G3)
Power Management
All devices in the system are turned off completely.
Soft Off (G2/S5)
OS initiated shutdown. All devices int he sytem are turned off
completely.
Working (G0/S0)
Individual devices such as the CPU and hard disk may be power
managed in this state.
S3 Sleeping State
CPU set power down
VGA suspend
PCMCIA suspend
Audio Power Down
Hard Disk Power Down
CD-ROM Power Down
Super I/O Low Power mode
S4 Sleeping State
Also called Hibernate stats. System saves all system state and
data onto disk prior to power off the whole system.
26
TravelMate 4060
Environmental Requirements
Item
Temperature
Specification
Operating
+0~+35 °C
-20~+65 °C
-20~+65 °C
Non-operating
Package storage
Humidity
Operating
10% to 90% RH, non-condensing
Non-operating
Non-operating
Vibration
10% to 90% RH, non-condensing (Unpacked)
10% to 90% RH, non-condensing (Storage package)
Operating (unpacked)
Non-operating (unpacked)
Operation vibration: 1.0G ,X,Y,Zaxis, 30 minutes/axis
5~27.1Hz: 0.6G
27.1~50Hz: 0.04mm (peak to peak)
50~500Hz: 2.0G
Non-operating (packed)
5~62.6Hz: 0.51mm (peak to peak)
62.6~500Hz: 4.0G
Mechanical Specification
Item
Specification
Dimensions
364(W) x 279(D) x 33.9/38.9 (H)mm
14.3 3X 10.98x 1.33/1.53 inches
Weight
6.4 Ibs (2.91kg) for 15” XGA LCD model
6.5 lbs (2.94kg) for 15.4” WXGA LCD model
I/O Ports
Three USB 2.0 ports
Ethernet (RJ-45) port
Modem (RJ-11) port
External display (VGA) port
Microphone-in jack
Line-in jack
Headphones/speaker/line-out jack
Type II PC Card slot
DC-in jack for AC adaptor
Drive Bays
Indicators
One
LED indicator for keyboard hot key: Caps Lock, Scroll Lock, NUmber lock
LED indicator for function indicator: System power-on, HDD/ODD, Wireless on/off,
Arcade LED mode, DC-in, Battery/Charging indicator
Switch
Power
Chapter 1
27
Chapter 2
System Utilities
BIOS Setup Utility
The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/
Output System).
Your computer is already properly configured and optimized, and you do not need to run this utility. However, if
you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4
Troubleshooting when problem arises.
To activate the BIOS Utility, press mduring POST (when “Press <F2> to enter Setup” message is prompted
on the bottom of screen).
Press mto enter setup. The default parameter of F12 Boot Menu is set to “disabled”. If you want to change
boot device without entering BIOS Setup Utility, please set the parameter to “enabled”.
Press <F12> during POST to enter multi-boot menu. In this menu, user can change boot device without
entering BIOS SETUP Utility.
PhoenixBIOS Setup Utility
Main
Security
Boot
Exit
Info.
Intel (R) Pentium (R) processor 1.73GHz
CPU Type :
1733MHz
CPU Speed :
HDD Model Name:
TOSHIBA MK1031GAS
751U0320S
HDD Serial Number :
ATAPI Device :
HL-DT-ST DVD-RW GWA-4082N
System BIOS Version : 2A02
Alviso 1219
VGA BIOS Version :
KBC Version :
1A16
LXT123456705290116EF00
Serial Number :
Asset Tag Number :
Produce Name
Manufacturer Name:
UUID :
N/A
Aspire 1640
Acer
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
↑ ↓
F1 Help
Select Item
F5/F6 Change Values
Enter Select Sub-Menu
F9 Setup Defaults
F10 Save and Exit
← →
Esc Exit
Select Menu
4
Chapter 2
28
Navigating the BIOS Utility
There are six menu options: Info., Main, System Devices, Security, Boot, and Exit.
Follow these instructions:
T
T
T
T
T
T
To choose a menu, use the cursor left/right keys (zx).
To choose a parameter, use the cursor up/down keys ( wy).
To change the value of a parameter, press por q.
A plus sign (+) indicates the item has sub-items. Press eto expand this item.
Press ^while you are in any of the menu options to go to the Exit menu.
In any menu, you can load default settings by pressing t. You can also press uto save any
changes made and exit the BIOS Setup Utility.
NOTE: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys for a
particular menu are shown on the bottom of the screen. Help for parameters are found in the Item
Specific Help part of the screen. Read this carefully when making changes to parameter values. Please
note that system information vary in models.
29
Chapter 2
Information
PhoenixBIOS Setup Utility
Security Boot Exit
Main
Info.
Intel (R) Pentium (R) processor 1.73GHz
CPU Type :
1733MHz
CPU Speed :
HDD Model Name:
TOSHIBA MK1031GAS
751U0320S
HDD Serial Number :
ATAPI Device :
HL-DT-ST DVD-RW GWA-4082N
System BIOS Version : 2A02
Alviso 1219
VGA BIOS Version :
KBC Version :
1A16
LXT123456705290116EF00
Serial Number :
Asset Tag Number :
Produce Name
Manufacturer Name:
UUID :
N/A
Aspire 1640
Acer
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
↑ ↓
F1 Help
Select Item
F5/F6 Change Values
Enter Select Sub-Menu
F9 Setup Defaults
F10 Save and Exit
← →
Esc Exit
Select Menu
4
NOTE: The system information is subject to different models.
Parameter
HDD Model Name
HDD Serial Number
ATAPI Device
Description
This field shows the model name of HDD installed on primary IDE master.
This field displays the serial number of HDD installed on primary IDE master.
This field displays the mofel name of devices installed on secondary IDE master. The hard
disk drive or optical drive model name is automatically detected by the system.
System BIOS Version
VGA BIOS Version
KBC Version
This field displays the BIOS version of the system.
This field displays the VGA BIOS version of this system.
This filed displays the KBC version of this system.
ATAPI Serial Number
Serial Number
This field shows the serial number of devices installed on secondary IDE master.
This field displays the serial number of this unit.
Asset Tag Number
An Asset Tag with 32 bytes will be stored in EEPROM. Default value is set as
“0000000000000000” (in binary code).
Chapter 2
30
Parameter
UUID Number
Description
This will be visible only when there is an internal LAN device present. UUID means
Universally Unique ID, a method for computing object identifiers (OIDs). It uses the serial
number in the local Ethernet card combined with the date and time to generate a 128 bit
(16bytes) number. For Acer product, this field displays UUID number. A UUID string will be
stored in the secured data area which is an alphanumeric string of maxium 16 bytes in
length.
31
Chapter 2
Main
The Main screen displays a summary of your computer hardware information, and also includes basic setup
parameters. It allows the user to specify standard IBM PC AT system parameters.
PhoenixBIOS Setup Utility
Information
Security
Boot
Exit
Main
Item Specific Help
System Time:
System Date:
[05:45:48]
[08/30/2005]
<Tab>, <Shift-Tab>, or
<Enter> selects field.
Shows system base memory size
Shows extended memory size
VGA memory size
System Memory:
640 KB
Extended Memory:
Video Memory
1040 MB
[128MB]
Quiet Boot:
[Enabled]
Power On Display:
Network Boot
[Both]
[Enabled]
F12 Boot Menu
D2D Recovery
[Disabled]
[Enabled]
↑ ↓
F1 Help
Esc Exit
Select Item
F5/F6 Change Values
F9 Setup Defaults
F10 Save and Exit
← →
Select Menu
Enter Select
Sub-Menu
4
NOTE: The screen above is for reference only. Actual values may differ.
Chapter 2
32
The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.
Parameter
System Time
Description
Format/Option
Format: HH:MM:SS
Sets the system time. The hours are displayed
with 24-hour format.
(hour:minute:second) System Time
System Date
Sets the system date.
Format MM/DD/YYYY (month/day/
year)
System Date
System Memory
This field reports the memory size of the system.
Memory size is fixed to 640MB
Extended Memory
This field reports the memory size of the
extended memory in the system.
Extended Memory size=Total memory size-1MB
VGA Memory
Quiet Boot
Shows the VGA memory size. VGA Memory
size=64/128MB
Determines if Customer Logo will be displayed or
not; shows Summary Screen is disabled or
enabled.
Option: Enabled or Disabled
Enabled: Customer Logo is displayed, and
Summary Screen is disabled.
Disabled: Customer Logo is not displayed, and
Summary Screen is enabled.
Power on display
Auto: During power process, the system will
detect if any display device is connected on
external video port. If any external display device
is connected, the power on display will be in CRT
(or projector) only mode. Otherwise it will be in
LCD only mode.
Option: Both or Auto
Both: Simultaneously enable both the integrated
LCD screen and the system’s external video port
(for an external CRT or projector).
Network Boot
Enables, disables the system boot from LAN
(remote server).
Option: Enabled or Disabled
F12 Boot Menu
D2D Recovery
Enables, disables Boot Menu during POST.
Option: Disabled or Enabled
Enables, disables D2D Recovery function. The
function allows the user to create a hidden
partition on hard disc drive to store operation
system and restore the system to factory
defaults.
Option: Enabled or Disabled
NOTE: The sub-items under each device will not be shown if the device control is set to disable or auto. This is
because the user is not allowed to control the settings in these cases.
33
Chapter 2
Security
The Security screen contains parameters that help safeguard and protect your computer from unauthorized
use.
PhoenixBIOS Setup Utility
Security
Boot
Information
Main
Exit
Item Specific Help
Clear
Clear
Clear
Supervisor Password Is :
User Password Is :
HDD Password Is :
HDD Master ID :
Supervisor Password
controls accesses of the
whole setup utility.
15422442
[Enter]
[Enter]
[Enter]
Set Supervisor Password
Set User Password
Set HDD Password
It can be used to
boot up when Password
on boot is enabled.
[Disabled]
Password on Boot
↑ ↓
F1 Help
Esc Exit
Select Item
F5/F6 Change Values
Enter Select Sub-Menu
F9 Setup Defaults
F10 Save and Exit
← →
Select Menu
4
Chapter 2
34
The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.
Parameter
User Password Is
Description
Option
Clear or Set
Shows the setting of the user password.
Supervisor Password Is
Shows the setting of the Supervisor password.
Please note that Supervisor Password controls
access to the entire Setup. The Supervisor
Password can be used to boot up when
Password on boot is set to enabled.
Clear or Set
HDD Password Is
Set User Password
Shows the setting of the HDD password.
Clear or Set
Press Enter to set the user password. When
user password is set, this password protects
the BIOS Setup Utility from unauthorized
access. The user can enter Setup menu only
and does not have right to change the value of
parameters.
Set Supervisor Password
Press Enter to set the supervisor password.
When set, this password protects the BIOS
Setup Utility from unauthorized access. The
user can not either enter the Setup menu nor
change the value of parameters.
Set HDD Password
Press Enter to set the HDD password.
Primary Harddisk Security
This feature is available to user when
Supervisor password is set. Password can be
written on HDD only when Supervisor
password or user password is set and
password on HDD is set to enabled.
Supervisor Password is written to HDD only
when Supervisor password is being set. User
password is written to HDD when both
passwords are set. When both Supervisor and
user password are present, both passwords
can unlock the HDD.
Disabled or Enabled
Password on Boot
Defines whether a password is required or not
while the events defined in this group
happened. The following sub-options are all
requires the Supervisor password for changes
and should be grayed out if the user password
was used to enter setup.
Disabled or Enabled
NOTE: When you are prompted to enter a password, you have three tries before the system halts. Don’t forget
your password. If you forget your password, you may have to return your notebook computer to your
dealer to reset it.
NOTE: The User Password can chagne the following items in BIOS: System Date, System Time and Power
on Display on Main menu, System Devices menu and Set User Password function on Security menu.
Meanwhile, the Supervisor Password can change ALL settings in BIOS.
Setting a Password
Follow these steps as you set the user or the supervisor password:
1. Use the wandykeys to highlight the Set Supervisor Password parameter and press the ekey. The
Set Supervisor Password box appears:
35
Chapter 2
2. Type a password in the “Enter New Password” field. The password length can not exceeds 8
alphanumeric characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the “Confirm New
Password” field.
IMPORTANT:Be very careful when typing your password because the characters do not appear on the screen.
3. Press e.
After setting the password, the computer sets the User Password parameter to “Set”.
4. If desired, you can opt to enable the Password on boot parameter.
5. When you are done, press uto save the changes and exit the BIOS Setup Utility.
Removing a Password
Follow these steps:
1. Use the wand ykeys to highlight the Set Supervisor Password parameter and press the ekey. The
Set Password box appears:
2. Type the current password in the Enter Current Password field and press e.
3. Press etwice without typing anything in the Enter New Password and Confirm New Password fields.
The computer then sets the Supervisor Password parameter to “Clear”.
4. When you have changed the settings, press uto save the changes and exit the BIOS Setup Utility.
Changing a Password
1. Use the wand ykeys to highlight the Set Supervisor Password parameter and press the ekey. The
Set Password box appears:
2. Type the current password in the Enter Current Password field and press e.
Chapter 2
36
3. Type a password in the Enter New Password field. Retype the password in the Confirm New Password
field.
4. Press e. After setting the password, the computer sets the User Password parameter to “Set”.
5. If desired, you can enable the Password on boot parameter.
6. When you are done, press uto save the changes and exit the BIOS Setup Utility.
If the verification is OK, the screen will display as following.
The password setting is complete after the user presses u.
If the current password entered does not match the actual current password, the screen will show you the
Setup Warning.
If the new password and confirm new password strings do not match, the screen will display the following
message.
37
Chapter 2
Boot
This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices
includes the distette drive in module bay, the onboard hard disk drive and the CD-ROM in module bay.
PhoenixBIOS Setup Utility
Boot
Info.
Main
Advanced
Security
Exit
Item Specific Help
CD-ROM/DVD Drive
Floppy Devices
+Hard Drive
+ and - indicate device
categories. Use <Enter> to
expand/collapses.
Network Boot
Boot order is top-down using
only the top device in each
category.
Use <F6> and <F5> to move
highlighted item up and down.
↑ ↓
F1 Help
Esc Exit
Select Item
F5/F6 Change Values
F9 Setup Defaults
← →
4
Select Menu
Enter Select
Sub-Menu
F10 Save and Exit
Chapter 2
38
Exit
The Exit screen contains parameters that help safeguard and protect your computer from unauthorized use.
PhoenixBIOS Setup Utility
Advanced Security
Exit
Info.
Main
Boot
Item Specific Help
Exit Saving Changes
Exit System Setup and save
your changes to CMOS.
Exit Dicarding Changes
Load Setup Defaults
Discard Changes
Save Changes
↑ ↓
F1 Help
Esc Exit
Select Item
F5/F6 Change Values
F9 Setup Defaults
← →
4
Select Menu
Enter Select
Sub-Menu
F10 Save and Exit
The table below describes the parameters in this screen.
Parameter
Description
Exit Saving Changes
Exit Discarding Changes
Load Setup Default
Discard Changes
Exit System Setup and save your changes to CMOS.
Exit utility without saving setup data to CMOS.
Load default values for all SETUP item.
Load previous values from CMOS for all SETUP items.
Save Setup Data to CMOS.
Save Changes
39
Chapter 2
BIOS Flash Utility
The BIOS flash memory update is required for the following conditions:
T
T
T
New versions of system programs
New features or options
Restore a BIOS when it becomes corrupted.
Use the Phlash utility to update the system BIOS flash ROM.
NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery
Diskette before you use the Phlash utility.
NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.
NOTE: Please use the AC adaptor power supply when you run the Phlash utility. If the battery pack does not
contain enough power to finish BIOS flash, you may not boot the system because the BIOS is not
completely loaded.
Create Crisis Recovery Diskette
1. Rename BIOS file of this product to BIOS.wph
2. Copy BIOS.wph file to crisis folder and overwrite the original BIOS.wph file.
3. Insert a blank floppy diskette to floppy drive.
4. Run cs.bat and follow its instructions to create crisis recovery diskette.
Recover BIOS from Crisis Recovery Diskette
1. Insert the crisis recovery diskette to the floppy drive.
2. Use AC adaptor power supply.
3. Press Fn and ESC key together for more than two seconds when you power on the system.
4. The system will read the files inside the floppy diskette without backlight.
5. After one to three minutes, the system will automatically reboot. Please do not shut down the system or
remove the power supply.
6. After step 1 to 5, you sould be able to recover BIOS already. Then you can see the LCD screen with the
backlight is on.
Chapter 2
40
41
Chapter 2
Chapter 3
Machine Disassembly and Replacement
This chapter contains step-by-step procedures on how to disassemble the notebook computer for
maintenance and troubleshooting.
To disassemble the computer, you need the following tools:
T
T
T
T
T
T
Wrist grounding strap and conductive mat for preventing electrostatic discharge
Flat-bladed screw driver
Phillips screw driver
Tweezers
Plastic Flat-bladed screw driver
Hexed Screw Driver
NOTE: The screws for the different components vary in size. During the disassembly process, group the
screws with the corresponding components to avoid mismatch when putting back the components.
Chapter 3
42
General Information
Before You Begin
Before proceeding with the disassembly procedure, make sure that you do the following:
1. Turn off the power to the system and all peripherals.
2. Unplug the AC adapter and all power and signal cables from the system
.
NOTE: Aspire 9100 series product uses mylar or tape to fasten the FFC/FPC/connectors/cable, you may
need to tear the tape or mylar before you disconnect different FFC/FPC/connectors.
43
Chapter 3
Disassembly Procedure Flowchart
The flowchart on the succeeding page gives you a graphic representation on the entire disassembly sequence
and instructs you on the components that need to be removed during servicing. For example, if you want to
remove the main board, you must first remove the keyboard, then disassemble the inside assembly frame in
that order.
Start
Battery
*2
*2
E*2
RAM/Wireless
Cover
HDD Cover
IO Bezel
ODD Module
*2 back side
*4 left/right side
*2
ODD
Connector
Board
Heatsink
Cover
HDD Module
ODD Holder
Wireless LAN
Card
Memory
special screw for thermal*3
Ex1
Thermal
Module
CPU
ODD Drive
E*3
Middle Cover
B*2
Keyboard
*4
(right and left hinges)
LCD Module
B*2
Switch Board
B*5
E*16+B*2
Lower and
Upper Case
Assembly
Lower Case
Assembly
Upper Case
Assembly
Touchpad
E*2
*2 screw nuts
*4
B*2
B*2
*3
Touchpad
Bracket
Bluetooth
Module
Touchpad
Board
VGA Heatsink
Main Board
3-in-1 Cover
Speaker Set
Modem Board
Chapter 3
44
LCD Module
4 screw pads
M*4
LCD Bezel
*6 hinges
*2 brackets
LCD Inverter
LCD
Assembly
Antenna set
LCD Cover
*4
LCD
LCD Cable
LCD Brackets
Screw List
Item
Description
A
SCREW F040 9 5.0X5.0 9.5X(IO) R00
SCREW M2.0X0.4P+3FP ZK(NL)
SCREW M2.5 K 5/2 X0.85 4 ZK(NL)
SCREW M2.5X0.45+10K NIL
SCREW M2.5X0.45+8K ZBL
B
C
D
E
F
SCREW M2.5X0.45P+3F NI
G
SCREW M3.0X0.8P+3K NL
45
Chapter 3
Removing the Battery Pack
1. Unlock the battery lock.
2. Slide the battery latch as shown.
3. Then remove the battery pack.
Chapter 3
46
Removing the HDD Module/the Memory and the Wireless LAN Card/
the Thermal Module and the CPU/ODD Module and LCD Module
Removing the HDD Module
1. Remove the two screws holding the HDD cover.
2. Remove the HDD cover.
3. Remove the screw fastening the HDD module to the notebook.
4. Then detach the HDD module from the notebook.
Removing the Memory and the Wireless LAN Card
1. Remove the two screws that secure the RAM/Wireless cover.
2. Remove the RAM/Wireless cover.
3. Pop up the memory then remove it.
4. Disconnect the auxiliary and the main wireless antennae.
5. Pop the wireless LAN card then remove it.
47
Chapter 3
.
Removing the Thermal Module and CPU
1. Remove the three screws holding the thermal door
2. Detach the thermal door.
3. Disconnect the fan cable from the main board.
4. Remove the three screws fastening the thermal module.
5. Disconnect the fan cable.
NOTE: When you remove the screws fastening the thermal module, please follow the number order 3, 2, 1 on
the thermal module. When you need to assemble the thermal module, fasten the screws as the order 1,
2, 3 on the thermal module.
6. Use a flat-bladed screwdriver to release the CPU lock.
7. Remove the CPU from the socket carefully.
Chapter 3
48
Removing the ODD Module
1. Remove the three screws holding the middle cover.
2. Detach the middle cover carefully.
3. Then remove the two screws fastening the keyboard.
4. Turn over the keyboard as shown.
5. Disconnect the keyboard cable from the main board then remove the keyboard.
6. Remove the screw that fastens the ODD module.
7. Turn over the notebook computer then detach the ODD module carefully.
NOTE: When you reattach the ODD, please make sure you attach the ODD module completely to the main
unit. Otherwise, you can not fasten the screw and the screw may damage the main board.
.
Removing the LCD Module
1. Remove the three screws holding the keyboard cover.
2. Open the LCD module as the picture shown then detach the keyboard cover from the main unit.
.
49
Chapter 3
3. Remove the two screws that secure the keyboard as shown.
4. Turn over the keyboard as shown and disconnect the keyboard cable then remove the keyboard.
5. Pull out the antenna set with a tweezers then take out the antenna set from the main unit.
.
6. Disconnect the LCD coaxial cable.
7. Remove the four screws holding the right and the left hinge. Two on each side.
8. Then detach the LCD module from the main unit.
.
Chapter 3
50
Disassembling the Main Unit
Separate the Main Unit Into the Upper and the Lower Case Assembly
1. Remove the two screws holding the switch board.
2. Remove the switch board.
3. Disconnect the touchpad FFC from the main board.
4. Disconnect the bluetooth cable.
5. Remove the five screws that secure the upper case.
6. Remove the 17 screws on the bottom as shown.
7. Detach the upper case assembly and place it next to the lower case assembly.
8. Disconnect the microphone cable then remove the upper case assembly.
Disassembling the Upper Case Assembly
1. Disconnect the touchpad board to touchpad FFC.
2. Disconnect the touchpad board to main board FFC.
3. Then detach the touchpad board to main board FFC from the touchpad board.
51
Chapter 3
4. Remove the three screws that secure the touchpad board.
5. Remove the touchpad board from the upper case.
6. Disconnect the touchpad board to touchpad FFC.
7. Remove the touchpad board to touchpad FFC from the uppwer case assembly.
8. Remove the four screws holding the touchpad bracket.
9. Detach the touchpad bracket from the upper case assembly.
10. Remove the touchpad from the upper case.
11. Remove the two screws that secure the bluetooth module.
12. Disconnect the bluetooth module then remove it.
Disassembling the Lower Case Assembly
1. Disconnect the MDC cable from the modem board.
Chapter 3
52
2. Detach the MDC cable from the main board.
3. Remove the two screws holding the modem board then disconnect the modem board from the main
board.
4. Disconnect the speaker cable from the main board.
5. Remove the screw that secure the main board.
6. Remove the two screw nuts as shown.
7. The you can detach the main board from the upper case.
8. Remove the ttwo screws that fasten the N/B heatsink.
9. Remove the N/B heatsink from the main board as shown.
10. Remove the card reader dummy card from the lower case. (For SKU with three-in-one card reader, please
remove three in one cover).
11. Remove the two screws that secure the speaker set on one side.
12. Then remove another two screws holding the speaker set on the other side.
13. Then take out the speaker set from the lower case.
53
Chapter 3
IMPORTANT:When assembling/disassembling the main board, whenever there is a mylar on the main board
(see the highlighted with red below; the mylar is sami-transparent, film-like stuff ), it should be
transferred “if necessary” to the replacement main board. Because the main board mylar should be
stuck to the main board to prevent the antenna cable and the main board components short circuit.
The short could cause the main board or the antenna cable burned.
Chapter 3
54
Disassembling the LCD Module
1. Remove the four screw caps as shown.
2. Remove the four screws holding the LCD bezel.
3. Then detach the LCD bezel from the LCD module.
4. Disconnect the inverter board then remove it.
5. Remove the three screws holding the right hinge.
6. Then remove the three screws that secure the left hinge.
7. Remove one screw that secure the LCD bracket.
8. Remove another screw holding the LCD bracket on the other side.
9. Then detach the LCD panel from the LCD cover carefully.
.
10. Remove the two screws holding the right bracket.
11. Then remove the right bracket.
12. Remove another two screws that tighten the left bracket.
55
Chapter 3
13. Remove the left bracket as the picture shows.
14. Tear off the tape fastening the LCD cable.
15. Tear off the the LCD cable fastening the LCD cable, then remove it..
Chapter 3
56
Disassembling the External Modules
Disassembling the HDD Module
1. Remove the two screws holding the HDD bracket on one side.
2. Remove another two screws holding the HDD bracket on the other side.
3. Then take the hard disc drive out from the HDD bracket.
Disassembling the Optical Drive Module
1. Remove the four screws as the picture shows.
2. Remove the two screws that secure the optical disc drive and the ODD holder.
3. Push the ODD holder as shown.
4. Detach the ODD holder.
5. Disconnect the ODD connector board then remove it.
57
Chapter 3
Chapter 4
Troubleshooting
Use the following procedure as a guide for computer problems.
NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or
modified options can give false errors and invalid system responses.
1. Obtain the failing symptoms in as much detail as possible.
2. Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating
the same operation.
3. Use the following table with the verified symptom to determine which page to go to.
Symptoms (Verified)
Power failure. (The power indicator does not go
on or stay on.)
POST does not complete. No beep or error
codes are indicated.
“Power-On Self-Test (POST) Error Message” on
page 63
POST detects an error and displayed messages “Error Message List” on page 64
on screen.
Other symptoms (i.e. LCD display problems or
others).
page 63
Symptoms cannot be re-created (intermittent
problems).
“Power-On Self-Test (POST) Error Message” on
page 63
“Intermittent Problems” on page 74
“Undetermined Problems” on page 75
Chapter 4
58
System Check Procedures
External Diskette Drive Check
Do the following to isolate the problem to a controller, driver, or diskette. A write-enabled, diagnostic diskette is
required.
NOTE: Make sure that the diskette does not have more than one label attached to it. Multiple labels can cause
damage to the drive or cause the drive to fail.
Do the following to select the test device.
1. Boot from the diagnostics diskette and start the diagnostics program.
2. See if FDD Test is passed as the program runs to FDD Test.
3. Follow the instructions in the message window.
If an error occurs with the internal diskette drive, reconnect the diskette connector on the system board.
If the error still remains:
1. Reconnect the external diskette drive/DVD-ROM module.
2. Replace the external diskette drive/CD-ROM module.
3. Replace the main board.
External CD-ROM Drive Check
Do the following to isolate the problem to a controller, drive, or CD-ROM. Make sure that the CD-ROM does
not have any label attached to it. The label can cause damage to the drive or can cause the drive to fail.
Do the following to select the test device:
1. Boot from the diagnostics diskette and start the diagnostics program.
2. See if CD-ROM Test is passed when the program runs to CD-ROM Test.
3. Follow the instructions in the message window.
If an error occurs, reconnect the connector on the System board. If the error still remains:
1. Reconnect the external diskette drive/CD-ROM module.
2. Replace the external diskette drive/CD-ROM module.
3. Replace the main board.
Keyboard or Auxiliary Input Device Check
Remove the external keyboard if the internal keyboard is to be tested.
If the internal keyboard does not work or an unexpected character appears, make sure that the flexible cable
extending from the keyboard is correctly seated in the connector on the system board.
If the keyboard cable connection is correct, run the Keyboard Test.
If the tests detect a keyboard problem, do the following one at a time to correct the problem. Do not replace a
non-defective FRU:
1. Reconnect the keyboard cables.
2. Replace the keyboard.
3. Replace the main board.
The following auxiliary input devices are supported by this computer:
T
T
Numeric keypad
External keyboard
If any of these devices do not work, reconnect the cable connector and repeat the failing operation.
59
Chapter 4
Memory check
Memory errors might stop system operations, show error messages on the screen, or hang the system.
1. Boot from the diagnostics diskette and start the doagmpstotics program (please refer to main board.
2. Go to the diagnostic memory in the test items.
3. Press F2 in the test items.
4. Follow the instructions in the message window.
NOTE: Make sure that the DIMM is fully installed into the connector. A loose connection can cause an error.
Power System Check
To verify the symptom of the problem, power on the computer using each of the following power sources:
1. Remove the battery pack.
2. Connect the power adapter and check that power is supplied.
3. Disconnect the power adapter and install the charged battery pack; then check that power is supplied by
the battery pack.
If you suspect a power problem, see the appropriate power supply check in the following list:
T
T
“Check the Power Adapter” on page 61
“Check the Battery Pack” on page 62
Chapter 4
60
Check the Power Adapter
Unplug the power adapter cable from the computer and measure the output voltage at the plug of the power
adapter cable. See the following figure
Pin 1: +19 to +20.5V
Pin 2: 0V, Ground
1. If the voltage is not correct, replace the power adapter.
2. If the voltage is within the range, do the following:
T
T
T
Replace the System board.
If the problem is not corrected, see “Undetermined Problems” on page 75.
If the voltage is not correct, go to the next step.
3. If the power-on indicator does not light up, check the power cord of the power adapter for correct
continuity and installation.
4. If the operational charge does not work, see “Check the Battery Pack” on page 62.
61
Chapter 4
Check the Battery Pack
To check the battery pack, do the following:
From Software:
1. Check out the Power Management in control Panel
2. In Power Meter, confirm that if the parameters shown in the screen for Current Power Source and Total
Battery Power Remaining are correct.
3. Repeat the steps 1 and 2, for both battery and adapter.
4. This helps you identify first the problem is on recharging or discharging.
From Hardware:
1. Power off the computer.
2. Remove the battery pack and measure the voltage between battery terminals 1(+) and 6(ground).
3. If the voltage is still less than 7.5 Vdc after recharging, replace the battery.
To check the battery charge operation, use a discharged battery pack or a battery pack that has less than 50%
of the total power remaining when installed in the computer.
If the battery status indicator does not light up, remove the battery pack and let it return to room temperature.
Re-install the battery pack.
If the charge indicator still does not light up, replace the battery pack. If the charge indicator still does not light
up, replace the DC/DC charger board.
Touchpad Check
If the touchpad doesn’t work, do the following actions one at a time to correct the problem. Do not replace a
non-defective FRU:
1. Reconnect the touchpad cables.
2. Replace the touchpad.
3. Replace the system board.
After you use the touchpad, the pointer drifts on the screen for a short time. This self-acting pointer movement
can occur when a slight, steady pressure is applied to the touchpad pointer. This symptom is not a hardware
problem. No service actions are necessary if the pointer movement stops in a short period of time.
Chapter 4
62
Power-On Self-Test (POST) Error Message
The POST error message index lists the error message and their possible causes. The most likely cause is
listed first.
NOTE: Perform the FRU replacement or actions in the sequence shown in FRU/Action column, if the FRU
replacement does not solve the problem, put the original part back in the computer. Do not replace a
non-defective FRU.
This index can also help you determine the next possible FRU to be replaced when servicing a computer.
If the symptom is not listed, see “Undetermined Problems” on page 75.
The following lists the error messages that the BIOS displays on the screen and the error symptoms classified
by function.
NOTE: Most of the error messages occur during POST. Some of them display information about a hardware
device, e.g., the amount of memory installed. Others may indicate a problem with a device, such as the
way it has been configured.
NOTE: If the system fails after you make changes in the BIOS Setup Utility menus, reset the computer, enter
Setup and install Setup defaults or correct the error.
63
Chapter 4
Index of Error Messages
Error Code List
Error Codes
Error Messages
Equipment Configuration Error
006
Causes:
1. CPU BIOS Update Code Mismatch
2. IDE Primary Channel Master Drive Error
(THe causes will be shown before “Equipment Configuration
Error”)
010
070
071
072
110
Memory Error at xxxx:xxxx:xxxxh (R:xxxxh, W:xxxxh)
Real Time Clock Error
CMOS Battery Bad
CMOS Checksum Error
System disabled.
Incorrect password is specified.
<No error code>
<No error code>
Battery critical LOW
In this situation BIOS will issue 4 short beeps then shut down
system, no message will show.
Thermal critical High
In this situation BIOS will shut down system, not show message.
Error Message List
Error Messages
FRU/Action in Sequence
Failure Fixed Disk
Reconnect hard disk drive connector.
System board
Stuck Key
see “Keyboard or Auxiliary Input Device Check” on page 59.
see “Keyboard or Auxiliary Input Device Check” on page 59.
see “Keyboard or Auxiliary Input Device Check” on page 59.
Unlock external keyboard
Keyboard error
Keyboard Controller Failed
Keyboard locked - Unlock key switch
Monitor type does not match CMOS - Run Setup Run “Load Default Settings” in BIOS Setup Utility.
Shadow RAM Failed at offset: nnnn
System RAM Failed at offset: nnnn
Extended RAM Failed at offset: nnnn
BIOS ROM
System board
DIMM
System board
DIMM
System board
System battery is dead - Replace and run Setup Replace RTC battery and Run BIOS Setup Utility to reconfigure
system time, then reboot system.
System CMOS checksum bad - Default
configuration used
RTC battery
Run BIOS Setup Utility to reconfigure system time, then reboot
system.
System timer error
RTC battery
Run BIOS Setup Utility to reconfigure system time, then reboot
system.
System board
Chapter 4
64
Error Message List
Error Messages
Real time clock error
FRU/Action in Sequence
RTC battery
Run BIOS Setup Utility to reconfigure system time, then reboot
system.
System board
Previous boot incomplete - Default configuration Run “Load Default Settings” in BIOS Setup Utility.
used
RTC battery
System board
Memory size found by POST differed from
CMOS
Run “Load Default Settings” in BIOS Setup Utility.
DIMM
System board
Diskette drive A error
Check the drive is defined with the proper diskette type in BIOS
Setup Utility
See “External Diskette Drive Check” on page 59.
Incorrect Drive A type - run SETUP
Check the drive is defined with the proper diskette type in BIOS
Setup Utility
System cache error - Cache disabled
CPU ID:
System board
System board
DMA Test Failed
DIMM
System board
Software NMI Failed
DIMM
System board
Fail-Safe Timer NMI Failed
Device Address Conflict
DIMM
System board
Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
Allocation Error for device
Failing Bits: nnnn
Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
DIMM
BIOS ROM
System board
Fixed Disk n
None
Invalid System Configuration Data
BIOS ROM
System board
I/O device IRQ conflict
Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
Operating system not found
Enter Setup and see if fixed disk and drive A: are properly identified.
Diskette drive
Hard disk drive
System board
65
Chapter 4
Error Message List
No beep Error Messages
FRU/Action in Sequence
No beep, power-on indicator turns off and LCD is Power source (battery pack and power adapter). See “Power
blank.
System Check” on page 60.
Ensure every connector is connected tightly and correctly.
Reconnect the DIMM.
LED board.
System board.
No beep, power-on indicator turns on and LCD is Power source (battery pack and power adapter). See “Power
blank.
System Check” on page 60.
Reconnect the LCD connector
Hard disk drive
LCD inverter ID
LCD cable
LCD Inverter
LCD
System board
No beep, power-on indicator turns on and LCD is Reconnect the LCD connectors.
blank. But you can see POST on an external
CRT.
LCD inverter ID
LCD cable
LCD inverter
LCD
System board
No beep, power-on indicator turns on and a
blinking cursor shown on LCD during POST.
Ensure every connector is connected tightly and correctly.
System board
No beep during POST but system runs correctly. Speaker
System board
Chapter 4
66
Phoenix BIOS Beep Codes
Code
Beeps
POST Routine Description
Verify Real Mode
02h
03h
04h
06h
08h
09h
0Ah
0Bh
0Ch
0Eh
0Fh
10h
11h
Disable Non-Maskable Interrupt (NMI)
Get CPU type
Initialize system hardware
Initialize chipset with initial POST values
Set IN POST flag
Initialize CPU registers
Enable CPU cache
Initialize caches to initial POST values
Initialize I/O component
Initialize the local bus IDE
Initialize Power Management
Load alternate registers with initial POST
values
12h
13h
14h
Restore CPU control word during warm boot
Initialize PCI Bus Mastering devices
Initialize keyboard controller
BIOS ROM checksum
16h
17h
18h
1Ah
1Ch
20h
22h
24h
26h
28h
29h
2Ah
2Ch
2Eh
1-2-2-3
Initialize cache before memory autosize
8254 timer initialization
8237 DMA controller initialization
Reset Programmable Interrupt Controller
Test DRAM refresh
1-3-1-1
1-3-1-3
Test 8742 Keyboard Controller
Set ES segment register to 4 GB
Enable A20 line
Autosize DRAM
Initialize POST Memory Manager
Clear 215 KB base RAM
1-3-4-1
1-3-4-3
RAM failure on address line xxxx
RAM failure on data bits xxxx of low byte of
memory bus
2Fh
30h
Enable cache before system BIOS shadow
1-4-1-1
RAM failure on data bits xxxx of high byte of
memory bus
32h
33h
36h
38h
3Ah
3Ch
3Dh
42h
45h
46h
Test CPU bus-clock frequency
Initialize Phoenix Dispatch Manager
Warm start shut down
Shadow system BIOS ROM
Autosize cache
Advanced configuration of chipset registers
Load alternate registers with CMOS values
Initialize interrupt vectors
POST device initialization
2-1-2-3
Check ROM copyright notice
67
Chapter 4
Code
Beeps
POST Routine Description
Check video configuration against CMOS
Initialize PCI bus and devices
Initialize all video adapters in system
QuietBoot start (optional)
48h
49h
4Ah
4Bh
4Ch
4Eh
50h
51h
52h
54h
58h
59h
5Ah
5Bh
5Ch
60h
62h
64h
66h
67h
68h
69h
6Ah
6Bh
6Ch
6Eh
Shadow video BIOS ROM
Display BIOS copyright notice
Display CPU type and speed
Initialize EISA board
Test keyboard
Set key click if enabled
2-2-3-1
Test for unexpected interrupts
Initialize POST display service
Display prompt “Press F2 to enter SETUP”
Disable CPU cache
Test RAM between 512 and 640 KB
Test extended memory
Test extended memory address lines
Jump to User Patch1
Configure advanced cache registers
Initialize Multi Processor APIC
Enable external and CPU caches
Setup System Management Mode (SMM) area
Display external L2 cache size
Load custom defaults (optional)
Display shadow-area message
Display possible high address for UMB
recovery
70h
72h
76h
7Ch
7Eh
80h
81h
82h
83h
84h
85h
86h
87h
Display error messages
Check for configuration errors
Check for keyboard errors
Set up hardware interrupt vectors
Initialize coprocessor if present
Disable onboard Super I/O ports and IRQs
Late POST device initialization
Detect and install external RS232 ports
Configure non-MCD IDE controllers
Detect and install external parallel ports
Initialize PC-compatible PnP ISA devices
Re-initialize onboard I/O ports
Configure Motherboard Configurable Devices
(optional)
88h
89h
8Ah
8Bh
8Ch
Initialize BIOS Area
Enable Non-Maskable Interrupts (NMIs)
Initialize Extended BIOS Data Area
Test and initialize PS/2 mouse
Initialize floppy controller
Chapter 4
68
Code
Beeps
POST Routine Description
Determine number of ATA drives (optional)
Initialize hard-disk controllers
8Fh
90h
91h
92h
93h
95h
96h
97h
98h
Initialize local-bus hard-disk controllers
Jump to UserPatch2
Build MPTABLE for multi-processor boards
Install CD ROM for boot
Clear huge ES segment register
Fixup Multi Processor table
1-2
Search for option ROMs. One long, two short
beeps on checksum failure.
99h
9Ah
9Ch
9Dh
9Eh
9Fh
A0h
A2h
A4h
A8h
AAh
ACh
AEh
B0h
B2h
B4h
B5h
B6h
B9h
BAh
BBh
BCh
BDh
BEh
BFh
C0h
C1h
C2h
C3h
C4h
C5h
C6h
C7h
C8h
C9h
D2h
Check for SMART drive (optional)
Shadow option ROMs
Set up Power Management
Initialize security engine (optional)
Enable hardware interrupts
Determine number of ATA and SCSI drives
Set time of day
Check key lock
Initialize Typematic rate
Erase F2 prompt
Scan for F2 key stroke
Enter SETUP
Clear Boot flag
Check for errors
POST done- prepare to boot operating system
One short beep before boot
Terminate QuietBoot (optional)
Check password (optional)
Prepare Boot
1
Initialize DMI parameters
Initialize PnP Option ROMs
Clear parity checkers
Display MultiBoot menu
Clear screen (optional)
Check virus and backup reminders
Try to boot with INT 19
Initialize POST Error Manager (PEM)
Initialize error logging
Initialize error display function
Initialize system error handler
PnPnd dual CMOS (optional)
Initialize notebook docking (optional)
Initialize notebook docking late
Force check (optional)
Extended checksum (optional)
Unknown interrupt
69
Chapter 4
Code
Beeps
E0h
E1h
E2h
E3h
E4h
E5h
E6h
E7h
E8h
E9h
EAh
EBh
ECh
EDh
EEh
EFh
F0h
F1h
F2h
F3h
F4h
F5h
F6h
F7h
Initialize the chipset
Initialize the bridge
Initialize the CPU
Initialize the system timer
Initialize system I/O
Check force recovery boot
Checksum BIOS ROM
Go to BIOS
Set Huge Segment
Initialize Multi Processor
Initialize OEM special code
Initialize PIC and DMA
Initialize Memory type
Initialize Memory size
Shadow Boot Block
System memory test
Initialize interrupt vectors
Initialize Run Time Clock
Initialize video
Initialize System Management Mode
Output one beep before boot
Boot to Mini DOS
1
Clear Huge Segment
Boot to Full DOS
Chapter 4
70
Index of Symptom-to-FRU Error Message
LCD-Related Symptoms
Symptom / Error
Action in Sequence
LCD backlight doesn't work
LCD is too dark
Enter BIOS Utility to execute “Load Setup Default Settings”, then
reboot system.
Reconnect the LCD connectors.
LCD brightness cannot be adjusted
LCD contrast cannot be adjusted
Keyboard (if contrast and brightness function key doesn't work).
LCD inverter ID
LCD cable
LCD inverter
LCD
System board
Unreadable LCD screen
Missing pels in characters
Abnormal screen
Reconnect the LCD connector
LCD inverter ID
LCD cable
Wrong color displayed
LCD inverter
LCD
System board
LCD has extra horizontal or vertical lines
displayed.
LCD inverter ID
LCD inverter
LCD cable
LCD
System board
Indicator-Related Symptoms
Symptom / Error
Action in Sequence
Indicator incorrectly remains off or on, but system Reconnect the inverter board
runs correctly
Inverter board
System board
Power-Related Symptoms
Symptom / Error
Action in Sequence
Power shuts down during operation
Power source (battery pack and power adapter). See “Power
System Check” on page 60.
Battery pack
Power adapter
Hard drive & battery connection board
System board
The system doesn’t power-on.
Power source (battery pack and power adapter). See “Power
System Check” on page 60.
Battery pack
Power adapter
Hard drive & battery connection board
System board
The system doesn’t power-off.
Battery can’t be charged
Power source (battery pack and power adapter). See “Power
System Check” on page 60.
Hold and press the power switch for more than 4 seconds.
System board
See “Check the Battery Pack” on page 62.
Battery pack
System board
71
Chapter 4
PCMCIA-Related Symptoms
Symptom / Error
Action in Sequence
System cannot detect the PC Card (PCMCIA)
PCMCIA slot assembly
System board
PCMCIA slot pin is damaged.
PCMCIA slot assembly
Memory-Related Symptoms
Symptom / Error
Action in Sequence
Memory count (size) appears different from
actual size.
Enter BIOS Setup Utility to execute “Load Default Settings, then
reboot system.
DIMM
System board
Speaker-Related Symptoms
Symptom / Error
Action in Sequence
In Windows, multimedia programs, no sound
comes from the computer.
Audio driver
Speaker
System board
Internal speakers make noise or emit no sound. Speaker
System board
Power Management-Related Symptoms
Symptom / Error
Action in Sequence
The system will not enter hibernation
Hard disk drive
System board
The system doesn't enter hibernation mode and See “S4 Sleeping State” on page 26.
four short beeps every minute.
Press Fn+oand see if the computer enters hibernation mode.
Touchpad
Keyboard
Hard disk drive
System board
The system doesn’t enter standby mode after
closing the LCD
LCD cover switch
System board
The system doesn't resume from hibernation
mode.
See “S4 Sleeping State” on page 26.
Hard disk drive
System board
The system doesn't resume from standby mode See “S4 Sleeping State” on page 26.
after opening the LCD.
LCD cover switch
System board
Battery fuel gauge in Windows doesn’t go higher Remove battery pack and let it cool for 2 hours.
than 90%.
Refresh battery (continue use battery until power off, then charge
battery).
Battery pack
System board
Chapter 4
72
Power Management-Related Symptoms
Symptom / Error
Action in Sequence
Reconnect hard disk/CD-ROM drives.
System hangs intermittently.
Hard disk connection board
System board
Peripheral-Related Symptoms
Symptom / Error
Action in Sequence
System configuration does not match the
installed devices.
Enter BIOS Setup Utility to execute “Load Default Settings”, then
reboot system.
Reconnect hard disk/CD-ROM/diskette drives.
External display does not work correctly.
Press Fn+F5, LCD/CRT/Both display switching
System board
USB does not work correctly
Print problems.
System board
Ensure the “Parallel Port” in the “Onboard Devices Configuration” of
BIOS Setup Utility is set to Enabled.
Onboard Devices Configuration
Run printer self-test.
Printer driver
Printer cable
Printer
System Board
Serial or parallel port device problems.
Ensure the “Serial Port” in the Devices Configuration” of BIOS Setup
Utility is set to Enabled.
Device driver
Device cable
Device
System board
Keyboard/Touchpad-Related Symptoms
Symptom / Error
Action in Sequence
Keyboard (one or more keys) does not work.
Reconnect the keyboard cable.
Keyboard
System board
Touchpad does not work.
Reconnect touchpad cable.
Touchpad board
System board
Modem-Related Symptoms
Symptom / Error
Action in Sequence
Internal modem does not work correctly.
Modem phone port
modem combo board
System board
NOTE: If you cannot find a symptom or an error in this list and the problem remains, see “Undetermined
Problems” on page 75.
73
Chapter 4
Intermittent Problems
Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a
hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement
should be considered only when a recurring problem exists.
When analyzing an intermittent problem, do the following:
1. Run the advanced diagnostic test for the system board in loop mode at least 10 times.
2. If no error is detected, do not replace any FRU.
3. If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.
Chapter 4
74
Undetermined Problems
The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect,
whether a short circuit is suspected, or whether the system is inoperative.
Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU).
NOTE: Verify that all attached devices are supported by the computer.
NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power
System Check” on page 60):
1. Power-off the computer.
2. Visually check them for damage. If any problems are found, replace the FRU.
3. Remove or disconnect all of the following devices:
T
T
T
T
T
T
T
Non-Acer devices
Printer, mouse, and other external devices
Battery pack
Hard disk drive
DIMM
CD-ROM/Diskette drive Module
PC Cards
4. Power-on the computer.
5. Determine if the problem has changed.
6. If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.
7. If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU:
T
T
System board
LCD assembly
75
Chapter 4
Chapter 6
FRU (Field Replaceable Unit) List
This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of TravelMate 4060.
Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization).
Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available
on your regional web or channel. For whatever reasons a part number change is made, it will not be noted on
the printed Service Guide. For ACER AUTHORIZED SERVICE PROVIDERS, your Acer office may have a
DIFFERENT part number code from those given in the FRU list of this printed Service Guide. You MUST use
the local FRU list provided by your regional Acer office to order FRU parts for repair and service of customer
machines.
NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or
regulations on how to dispose it properly, or follow the rules set by your regional Acer office on how to
return it.
Chapter 6
76
TravelMate 4060 Exploded Diagram
TravelMate 4060 FRU List
Adapter
NS
NS
NS
ADP 19V 3.42A PA-1650-02QR
90~264V LF
AP.06503.010
AP.06506.002
AP.06501.009
ADP 19V 3.42A SLS0335A19A57LF
90~264V EU
ADP 19V 3.42A SADP-65KB DBHF
90~264V LF
Battery
77
Chapter 6
TravelMate 4060 FRU List
NS
BATTERY SANYO LI-ION 4S2P 4.4A
4UR18650F-2-QC140
BT.T5003.001
BT.T5005.001
BT.00805.003
BT.00407.001
BT.00403.004
BT.00404.004
BATTERY PANASONIC LI-ION 4S2P
4.4A CGR-B/8B5AE
BATTERY PANASONIC LI-ION 4S2P
4.4A ROHS
BATTERY SIMPPLO PACK LI-ION
4S1P 2.0A
BATTERY SANYO PACK LI-ION
4S1P 2.0A
BATTERY SONY PACK LI-ION 4S1P
1.96A
Board
NS
NS
MODEM 56K (MDC)T60M845.02 EU
BLUETOOTH MODULE W/ANTENNA
54.TAKV7.001
54.T48V7.001
NS
W/L 802.11B/G(WM3B2200BGMW2)
KI.CAX01.008
NS
NS
LAUNCH BOARD
55.TAKV7.001
55.TAKV7.002
TOUCH PAD BOARD
Cable
NS
FFC CABLE - TP/B TO MB
50.A50V7.001
Chapter 6
78
TravelMate 4060 FRU List
NS
NS
MODEM CABLE
50.A510V7.001
POWER CORD US (3 PIN)
POWER CORD PRC (3 PIN)
POWER CORD KOERA ( Pin)
POWER CORD EU (3 PIN)
POWER CORD UK (3 PIN)
POWER CORD ITALIAN (3 PIN)
POWER CORD- SWISS
27.A03V7.001
27.A03V7.003
27.T23V7.006
27.A03V7.002
27.A03V7.004
27.A03V7.005
27.A03V7.007
27.A03V7.008
27.A03V7.006
27.T48V7.001
POWER CORD AU (3 PIN)
POWER CORD DANISH (3 PIN)
POWER CORD AF (3 PIN)
Case/Cover/Bracket Assembly
5
6
MIDDEL COVER ERGO W/BUTTON -
LIGHT GREEN SILVER
42.T50V7.101
UPPER CASE W/TOUCHPAD,
BRACKET, MIC,BLUETOOTH CABLE
60.T91V7.001
60.T91V7.002
UPPER CASE W/TOUCHPAD,
BRACKET, MIC W/O BLUETOOTH
CABLE
11
LOWER CASE W/SPEAKER
60.A51V7.002
13
DIMM/WIRELESS COVER
42.A50V7.001
42.A50V7.002
HEATSINK COVER W/O DOCKING
79
Chapter 6
TravelMate 4060 FRU List
NS
15
3 IN 1 DUMMY COVER
42.T51V7.003
42.T63V7.004
HDD COVER
14
HDD BRACKET
33.T50V7.001
Communication Module
NS
WIRELESS LAN ANTENNA
50.T50V7.003
CPU/Processor
NS
AMD MOBILE SEMPRON 2800+
25WD
KC.S2802.25D
KC.S3002.25D
AMD MOBILE SEMPRON 3000+
25WD
AMD MOBILE TURION 64 ML28
AMD MOBILE TURION 64 ML30
AMD MOBILE TURION 64 ML32
AMD MOBILE TURION 64 ML34
AMD MOBILE TURION 64 ML37
KC.TML02.280
KC.TML02.300
KC.TML02.320
KC.TML02.340
KC.TML02.370
Optical Disk Drive Module
NS
DVD/CDRW COMBO MODULE 24X
PHILIPS SCB5265 LF
6M.A65V7.004
Chapter 6
80
TravelMate 4060 FRU List
NS
DVD/CDRW COMBO DRIVE 24X
PHILIPS SCB5265 GB LF
KO.02403.007
NS
OPTICAL DEVICE HOLDER-FIX
42.T51V7.003
NS
DVD/CDRW BEZEL FOR G BASE
42.A65V7.003
DVD/CDRW COMBO MODULE KME
UJDA-770
6M.TAGV7.002
KO.02406.013
DVD/CDRW COMBO DRIVE 24X
KME UJDA-770
OPTICAL DEVICE HOLDER-FIX
DVD/CDRW BEZEL FOR G BASE
42.T51V7.003
42.A65V7.003
DVD/CDRW COMBO MODULE LITE-
ON SOSC-2483K LF
6M.ATKV7.001
KO.02409.011
DVD/CDRW COMBO LITE-ON
SOSC-2483K LF GB
OPTICAL DEVICE HOLDER-FIX
DVD/CDRW BEZEL FOR G BASE
42.T51V7.003
42.A65V7.003
DVD/CDRW COMBO MODULE HLDS
GCC-4244N LF
6M.ATKV7.002
KO.0240A.004
DVD/CDRW COMBO HLDS GCC-
4244N GB LF
OPTICAL DEVICE HOLDER-FIX
DVD DUAL BEZEL G BASE
42.T51V7.003
42.A65V7.003
DVD DUAL MODULE PANASONIC
UJ-840BAA2 G BASE
6M.A51V7.003
KU.00807.010
DVD DUAL DRIVE PANASONIC UJ-
840BAA2 D. LAYER G BASE
OPTICAL DEVICE HOLDER-FIX
DVD DUAL BEZEL G BASE
42.T51V7.003
42.A51V7.005
DVD DUAL MODULE LITE-ON
SOSW-833 DL G BASE
6M.T66V5.003
81
Chapter 6
TravelMate 4060 FRU List
DVD DUAL DRIVE LIET-ON SOSW-
833 DL G BASE
KU.00804.012
OPTICAL DEVICE HOLDER-FIX
DVD DUAL BEZEL G BASE
42.T51V7.003
42.A51V7.005
DVD DUAL MODULE PIONEER DVR-
K15RA F/W:1.05 G BASE
6M.ATKV7.003
KU.00805.020
DVD DUAL DRIVEPIONEER DVR-
K15RA D. LAYER F/W:1.05 G BASE
OPTICAL DEVICE HOLDER-FIX
DVD DUAL BEZEL G BASE
42.T51V7.003
42.A51V7.005
DVD DUAL MODULE HLDS GWA-
4082N G BASE
6M.ATKV7.004
KU.0080D.016
DVD DUAL DRIVE HLDS GWA-
4082N G BASE
OPTICAL DEVICE HOLDER-FIX
DVD DUAL BEZEL G BASE
42.T51V7.003
42.A51V7.005
HDD/Hard Disk Drive
NS
40G SEAGATE 2.5 IN. 4200RPM
KH.04001.016
N2.1ST9402113A (ROHS), F/W 3.01
40G TOSHIBA 2.5 IN. 4200RPM
PLUTO MK4025GAS (ROHS) F/W
KA100A
KH.04004.005
40G HGST 2.5 IN. 4200RPM
HAKONA-A F/W :A70G
KH.04007.013
KH.04008.025
KH.0400B.003
40G WD 2.5 IN. 5400RPM ML40
WD400UE-22HCT0 (ROHS)
40G SAMSUNG 2.5 IN. 5400RPM
M40MP0402H (ROHS) F/W YQ200-
04
60G SEAGATE 2.5 IN. 4200RPM
N2.2ST960812A F/W:3.04
KH.06001.003
KH.06004.004
60G TOSHIBA 2.5 IN. 4200RPM
PLUTO MK6025GAS (ROHS) F/W
KA200
60G HGST 2.5 IN. 4200RPM
HAKONE-A F/W :A70G
KH.06007.009
KH.06008.002
KH.08001.013
KH.08004.003
60G WD 2.5 IN. 5400RPM ML40
WD600UE-22HCT0 (ROHS)
80G SEAGATE 2.5 IN. 4200RPM
N2.2ST980829A F/W:3.04
80G TOSHIBA 2.5 IN. 4200RPM
PLUTO MK8025GAS (ROHS) F/W
KA023
Chapter 6
82
TravelMate 4060 FRU List
80G HGST 2.5 IN. 4200RPM
HAKONE-A F/W:A70G
KH.08007.011
KH.08008.027
KH.10004.001
80G WD 2.5 IN. 5400RPM ML40
WD800UE-22HCT0 (ROHS)
100G TOSHIBA 2.5 IN. 4200RPM
ARES MK1031GAS (ROHS) F/W
AA204A
100G HGST 2.5 IN. 4200RPM
HAKONE-A F/W:A70G
KH.10007.002
KB.A2707.001
Keyboard
NS
AS1680/AS1410 KEYBOARD
DARFON US International
AS1680/AS1410 KEYBOARD
DARFON Chinese
KB.A2707.002
KB.A2707.003
KB.A2707.004
KB.A2707.005
KB.A2707.006
KB.A2707.007
KB.A2707.008
KB.A2707.009
KB.A2707.010
KB.A2707.011
KB.A2707.012
KB.A2707.013
KB.A2707.014
KB.A2707.015
KB.A2707.016
KB.A2707.017
KB.A2707.018
KB.A2707.019
KB.A2707.020
AS1680/AS1410 KEYBOARD
DARFON Spanish
AS1680/AS1410 KEYBOARD
DARFON Thai
AS1680/AS1410 KEYBOARD
DARFON Brazilian Protugese
AS1680/AS1410 KEYBOARD
DARFON Korea
AS1680/AS1410 KEYBOARD
DARFON UK
AS1680/AS1410 KEYBOARD
DARFON German
AS1680/AS1410 KEYBOARD
DARFON Italian
AS1680/AS1410 KEYBOARD
DARFON French
AS1680/AS1410 KEYBOARD
DARFON Swiss/G
AS1680/AS1410 KEYBOARD
DARFON Portuguese
AS1680/AS1410 KEYBOARD
DARFON Arabic
AS1680/AS1410 KEYBOARD
DARFON Belgium
AS1680/AS1410 KEYBOARD
DARFON Sweden
AS1680/AS1410 KEYBOARD
DARFON Czech
AS1680/AS1410 KEYBOARD
DARFON Hungaian
AS1680/AS1410 KEYBOARD
DARFON Norway
AS1680/AS1410 KEYBOARD
DARFON Danish
AS1680/AS1410 KEYBOARD
DARFON Turkish
83
Chapter 6
TravelMate 4060 FRU List
AS1680/AS1410 KEYBOARD
DARFON Canadian French
KB.A2707.021
KB.A2707.022
KB.A2707.023
KB.A2707.024
KB.A2707.025
AS1680/AS1410 KEYBOARD
DARFON Japanese
AS1680/AS1410 KEYBOARD
DARFON Greek
AS1680/AS1410 KEYBOARD
DARFON Hebrew
AS1680/AS1410 KEYBOARD
DARFON Russian
LCD Module
NS
LCD 15.0 IN. MODULE SAMSUNG
LTN150XB-L03-V LF
6M.ATKV7.011
NS
LCD 15.0 IN. XGA SAMSUNG
LTN150XB-L03-V LF
LK.15006.008
NS
NS
LCD INVERTER BOARD
19.TAKV7.001
50.T50V7.004
LCD CABLE - 15 IN. XGA
NS
LCD BRACKET W/HINGE 15 IN. - L
33.T50V7.002
Chapter 6
84
TravelMate 4060 FRU List
NS
NS
LCD BRACKET W/HINGE 15 IN. - R
33.T50V7.003
60.T50V7.102
LCD PANEL W/LOGO ANTENNA 14/
15 IN.
NS
LCD BEZEL W/RUBBER PAD 15 IN.
60.T50V7.004
LCD 15.0 IN. MODULE CMO N150X3-
L07 LF
6M.ATKV7.012
LK.1500D.012
LCD 15.0 IN. XGA CMO N150X3-L07
REV C4 LF
NS
NS
NS
NS
NS
LCD INVERTER BOARD
19.TAKV7.001
50.T50V7.004
33.T50V7.002
33.T50V7.003
60.T50V7.102
LCD CABLE - 15 IN. XGA
LCD BRACKET W/HINGE 15 IN. - L
LCD BRACKET W/HINGE 15 IN. - R
LCD PANEL W/LOGO ANTENNA 14/
15 IN.
NS
LCD BEZEL W/RUBBER PAD 15 IN.
60.T50V7.004
LCD 15.0 IN. MODULE LPL
LP150X07-TLA2 LF
6M.ATKV7.013
LK.15008.019
LCD 15.0 IN. XGA LPL LP150X07-
TLA2 LF
NS
NS
NS
NS
NS
LCD INVERTER BOARD
19.TAKV7.001
50.T50V7.004
33.T50V7.002
33.T50V7.003
60.T50V7.102
LCD CABLE - 15 IN. XGA
LCD BRACKET W/HINGE 15 IN. - L
LCD BRACKET W/HINGE 15 IN. - R
LCD PANEL W/LOGO ANTENNA 14/
15 IN.
NS
LCD BEZEL W/RUBBER PAD 15 IN.
60.T50V7.004
6M.ATKV7.013
LCD 15.0 IN. MODULE LPL
LP150X07-TLA2 LF
85
Chapter 6
TravelMate 4060 FRU List
LCD 15.0 IN. XGA LPL LP150X07-
TLA2 LF
LK.15008.019
LCD INVERTER BOARD
19.TAKV7.001
50.T50V7.004
33.T50V7.002
33.T50V7.003
60.T50V7.102
LCD CABLE - 15 IN. XGA
LCD BRACKET W/HINGE 15 IN. - L
LCD BRACKET W/HINGE 15 IN. - R
LCD PANEL W/LOGO ANTENNA 14/
15 IN.
LCD BEZEL W/RUBBER PAD 15 IN.
60.T50V7.004
NS
NS
LCD MODULE 15.4 IN. WXGA CMO
N154I1-L09
6M.A51V7.013
LK.1540D.002
LCD 15.4 IN. WXGA CMO N154I1-
L09
NS
NS
2
LCD INVERTER BOARD
19.TAKV7.001
50.T50V7.006
33.T50V7.004
33.T50V7.005
60.T50V7.102
LCD CABLE - 15.4 IN. XGA
LCD BRACKET W/HINGE 15.4 IN. - L
LCD BRACKET W/HINGE 15.4 IN. - R
3
4
LCD PANEL W/LOGO ANTENNA 14/
15 IN.
1
LCD BEZEL W/RUBBER PAD 15.4 IN.
60.T50V7.006
LCD 15.4 MODULE SAMSUNG
LTN154X3-L01-V104
6M.ATKV7.014
LK.15406.009
LCD 15.4 WXGA SAMSUNG
LTN154X3-L01-V104
LCD INVERTER BOARD
19.TAKV7.001
50.T50V7.006
33.T50V7.004
33.T50V7.005
60.T50V7.103
LCD CABLE - 15.4 IN. WXGA
LCD BRACKET W/HINGE 15.4 IN. - L
LCD BRACKET W/HINGE 15.4 IN. - R
LCD PANEL W/LOGO ANTENNA
15.4 IN.
LCD BEZEL W/RUBBER PAD 15.4 IN.
60.T50V7.006
LCD 15.4 MODULE QDI QD15TL02-
03 LF NON-GLARE
6M.ATKV7.015
LK.15409.004
LCD 15.4 WXGA QDI QD15TL02-03
LF NON-GLARE
LCD INVERTER BOARD
19.TAKV7.014
50.T50V7.006
33.T50V7.004
33.T50V7.005
60.T50V7.103
LCD CABLE - 15.4 IN. WXGA
LCD BRACKET W/HINGE 15.4 IN. - L
LCD BRACKET W/HINGE 15.4 IN. - R
LCD PANEL W/LOGO ANTENNA
15.4 IN.
LCD BEZEL W/RUBBER PAD 15.4 IN.
60.T50V7.006
6M.ATKV7.016
LCD 15.4 IN. MODULE AU
B154EW01 V8 LF NON-G
Chapter 6
86
TravelMate 4060 FRU List
LCD 15.4 IN. WXGA AU B154EW01
V8 LF NON-G
LK.15405.005
LCD INVERTER BOARD
19.TAKV7.001
50.T50V7.006
33.T50V7.004
33.T50V7.005
60.T50V7.103
LCD CABLE - 15.4 IN. WXGA
LCD BRACKET W/HINGE 15.4 IN. - L
LCD BRACKET W/HINGE 15.4 IN. - R
LCD PANEL W/LOGO ANTENNA
15.4 IN.
LCD BEZEL W/RUBBER PAD 15.4 IN.
60.T50V7.006
LCD 15.0 IN. MODULE SAMSUNG
LTN150XB-L03-V W/O WIRELESS
6M.ATKV7.021
LK.15006.008
LCD 15.0 IN. XGA SAMSUNG
LTN150XB-L03-V LF
LCD INVERTER BOARD
19.TAKV7.001
50.T50V7.004
33.T50V7.002
33.T50V7.003
60.T56V7.102
LCD CABLE - 15 IN. XGA
LCD BRACKET W/HINGE 15 IN. - L
LCD BRACKET W/HINGE 15 IN. - R
LCD PANEL W/LOGO W/O
ANTENNA 14/15 IN.
LCD BEZEL W/RUBBER PAD 15 IN.
60.T50V7.004
LCD 15.0 IN. MODULE CMO N150X3-
L07 LF W/O WIRELESS
6M.ATKV7.022
LK.1500D.012
LCD 15.0 IN. XGA CMO N150X3-L07
REV C4 LF
LCD INVERTER BOARD
19.TAKV7.001
50.T50V7.004
33.T50V7.002
33.T50V7.003
60.A56V7.102
LCD CABLE - 15 IN. XGA
LCD BRACKET W/HINGE 15 IN. - L
LCD BRACKET W/HINGE 15 IN. - R
LCD PANEL W/LOGO W/O
ANTENNA 14/15 IN.
LCD BEZEL W/RUBBER PAD 15 IN.
60.T50V7.004
LCD 15.0 IN. MODULE LPL
LP150X07-TLA2 LF W/O WIRELESS
6M.ATKV7.023
LK.15008.019
LCD 15.0 IN. XGA LPL LP150X07-
TLA2 LF
LCD INVERTER BOARD
19.TAKV7.001
50.T50V7.004
33.T50V7.002
33.T50V7.003
60.A56V7.102
LCD CABLE - 15 IN. XGA
LCD BRACKET W/HINGE 15 IN. - L
LCD BRACKET W/HINGE 15 IN. - R
LCD PANEL W/LOGO W/O
ANTENNA 14/15 IN.
LCD BEZEL W/RUBBER PAD 15 IN.
60.T50V7.004
6M.ATKV7.025
LCD 15.4 MODULE QDI QD15TL02-
03 LF NON-GLARE W/O WIRELESS
87
Chapter 6
TravelMate 4060 FRU List
LCD 15.4 WXGA QDI QD15TL02-03
LF NON-GLARE
LK.15409.004
LCD INVERTER BOARD
19.TAKV7.001
50.T50V7.006
33.T50V7.004
33.T50V7.005
60.T56V7.103
LCD CABLE - 15.4 IN. WXGA
LCD BRACKET W/HINGE 15.4 IN. - L
LCD BRACKET W/HINGE 15.4 IN. - R
LCD PANEL W/LOGO ANTENNA
15.4 IN.
LCD BEZEL W/RUBBER PAD 15.4 IN.
60.T50V7.006
6M.ATKV7.026
LCD 15.4 IN. MODULE AU
B154EW01 V8 LF NON-G W/O
WIRELESS
LCD 15.4 IN. WXGA AU B154EW01
V8 LF NON-G
LK.15405.005
LCD INVERTER BOARD
19.TAKV7.001
50.T50V7.006
33.T50V7.004
33.T50V7.005
60.T56V7.103
LCD CABLE - 15.4 IN. WXGA
LCD BRACKET W/HINGE 15.4 IN. - L
LCD BRACKET W/HINGE 15.4 IN. - R
LCD PANEL W/LOGO ANTENNA
15.4 IN.
LCD BEZEL W/RUBBER PAD 15.4 IN.
60.T50V7.006
LB.TAK02.001
Main Board
NS
MAINBOARD 915GM UMA W/
PCMCIA W/O CPU MEMORY
Memory
NS
MEMORY DDR333 256MB INFINEON
HYS64D32020HDL-6-C (.11u)
KN.25602.012
KN.25603.019
KN.2560B.008
KN.2560G.001
KN.51202.025
KN.5120B.006
KN.5120G.006
MEMORY DDR333 256MB NANYA
NT256D64SH8C0GM-6K
MEMORY DDR333 256MB
SAMSUNG M470L3224FT0-CB3
MEMORY DDR333 256MB HYNIX
HYMD232M646D6-J
MEMORY DDR333 512MB INFINEON
HYS64D64020HBDL-6-C (.11u)
MEMORY DDR333 512MB
SAMSUNG M470L6524BT0-CB3
MEMORY DDR333 256MB HYNIX
HYMD564M646B6-J
Speaker
Chapter 6
88
TravelMate 4060 FRU List
N/S
SPEAKER SET
23.T50V7.001
Heatsink
10
THERMAL MODULE
60.A51V7.005
Miscellaneous
NS
NS
NS
NS
NAME PLATE - TM4060
RUBBER FOOT
1HYXZZZ24H9
1HYXZZZ24D6
47.T50V7.003
47.T50V7.004
LCD SCREW RUBBER PAD
LCD BEZEL RUBBER PAD
Screw
NS
NS
NS
NS
NS
NS
NS
NS
NS
NS
SCREW M2.0X3.0-I-NI-NYLOK
SCREW I2.5*3M-BNIH(M2.5L3)
SCREW M2.5*4L-BZN-NYLOK
SCREW M2.0X5-I-NI-NYLOK
SCREW MM25060IL69
86.A03V7.012
86.T25V7.012
86.A03V7.006
86.T23V7.006
86.A08V7.004
86.T23V7.010
86.A03V7.007
86.T25V7.008
86.T50V7.001
86.A03V7.011
SCREW M2.0*5-I(NI)(NYLOK)
SCREW M2.0X2.5-I-NI-NYLOK
SCREW I2*3M-NIHY (M2L3)
SCREW M1.7*3.0-I (BK)
SCREW I3*3.5M-NIH(M3L3.5)
89
Chapter 6
Chapter 6
90
|