Acer
Acer –LCD-D240H
Service Manual
LCD Monitor Acer D240H
Acer
Acer –LCD-D240H
Important Safety Notice
1. Safety precautions
This monitor is manufactured and tested on a ground principle that a user’s safety comes first.
However, improper used or installation may cause damage to the monitor as well as to the user.
Warning:
z
This monitor should be operated only at the correct power sources indicated on the label on the
rear of the monitor. If you’re unsure of the power supply in you residence, consult your local dealer
or Power Company.
z
z
Do not try to repair the monitor by yourself, as it contains no user-serviceable parts. This monitor
should only be repaired by a qualified technician.
Do not remove the monitor cabinet. There are high-voltage parts inside that may cause electric
shock to human bodies.
z
z
Stop using the monitor if the cabinet is damaged. Have it checked by a service technician.
Put your monitor only in a lean, cool, dry environment. If it gets wet, unplug the power cable
immediately and consult your closed dealer.
z
z
Always unplug the monitor before cleaning it. Clean the cabinet with a clean, dry cloth. Apply
non-ammonia based cleaner onto the cloth, not directly onto the class screen.
Do not place heavy objects on the monitor or power cord.
2. Product safety notice
Many electrical and mechanical parts in this chassis have special safety visual inspections and the
protection afforded by them cannot necessarily be obtained by using replacement components rated
for higher voltage, wattage, etc. Before replacing any of these components read the parts list in this
manual carefully. The use of substitute replacement parts, which do not have the same safety
characteristics as specified in the parts list, may create shock, fire, or other hazards.
3. Service notes
When replacing parts or circuit boards, clamp the lead wires around terminals before soldering.
Keep wires away from high voltage, high temperature components and sharp edges.
Keep wires in their original position so as to reduce interference.
z
z
z
z
Adjustment of this product please refers to the user’ manual.
Acer
Acer –LCD-D240H
01 Product Specification
1.
General:
Acer D240His designed with LVDS interface and VGA/DVI-D/HDMI input, and
Embedded DPF Function ,it featured with embedded universal AC power supplies and audio input. It’s
a green product and meets all ROHS standard. The power button and display control buttons are on
the front of the monitor. The monitors shall automatically to display lower resolution video modes into
1920x1080 full screen display. Itcan support 720P when DPF Mode,The image can be adjusted
through OSD control. It support HDCP and color management function.
1.1 Main Features
Maximum resolution
Back light system
Pixel pitch
: 1920(x3) x 1080 @ 60Hz
: 4 CCFL (top & bottom edge side)
: 276.75 um (H) x 276.75 um (V)
: 531.36mm (H) x 298.89mm (V)
: 300cd/m² (TYP.)
Display area
Brightness
Contrast ratio
DCR
: 1000
׃ 1 (TYP.) :80000:1 (Max)
Response time (Tr+Tf)
: 5ms (TYP. ON/OFF)
2ms (Gray to Gray)
Viewing angle
Input interface
: 170° (H)/ 160°(V), (TYP.)
: Analog (D-sub 15 pin)
Digital Option (DVI-D 24 pin & HDMI 19Pin)
: Compatible with VESA DPMS
: VESA DDCCI
Power management
Plug & Play
OSD language
: English, French, Spanish, Italian, Deutsch,
Simplified Chinese, Traditional Chinese, Japanese
(Dutch, Finnish, Russian depend on sale region)
Universal AC power supply
1.2 Accessories
AC Power Cord
VGA cable
: 1.8 m. (Black. Cord type depend on sale region)
: 1.8 m. (15 pin D-SUB, black cable with blue male connector)
: English (640Mb CD)
User manual
Warranty card
DVI cable (option)
:
: 1.8 m. (18+1 pin, black cable with white connector)
HDMI cable (option) : 1.8 m. (19 pin, black cable with white connector)
Acer
Acer –LCD-D240H
USB: USB2.0 (optional function)
Webcam: 1.0M resolution(1280 x 800), standard USB2.0 interface, array microphone
(optional function)
2.
Operation Specifications
The unit should suffer no visible cosmetic damage and should operate with no degradation in display quality
during exposure to the operating conditions and after exposure to the non-operating conditions, in any
sequence.
2.1 Environmental conditions
Operating
Temperature range
Relative humidity
Altitude
Specification
0°C to 50°C
5% to 90%
0 to 3048M (10000 ft)
Storage
-20°C to 60°C
Temperature range
Relative humidity
Altitude
5% to 90% (not condense)
0 to 9144M (30000 ft)
2.2 Safety, EMC, Ergonomics and Compatibility Requirements
Items
Description
UL/c
●
CB
●
TUV/G
CCC
Other
Safety
●
CCC
●
●
VCCI-B
●
FCC
●
CE
●
EMC
TCO TCO03
Ergonomics
Compatibility
●
●
Windows
●
Windows 2000
Windows Windows
●
●
●
Power
Energy Star
●
Management
2.3 Electrostatic Discharge Requirements
Acer
Acer –LCD-D240H
Item
Condition
Spec
Contact discharge: 4KV
Contact discharge: 8KV
Electrostatic
Discharge
●
●
IEC61000-4-2(EN55024)
Air discharge
Air discharge
: 8KV
: 15KV
Reliability
Items
Condition
Spec
Note
T=25℃
>50,000 Hours，
MTBF
Luminance
50,000 Hours(Typ)
CCFL Life time
Note1
becomes 50%
Note1. Display an all WHITE field at mid Brightness and Contrast settings.
3.
Electrical and Optical Characteristics and Performance
3.1 Main Power Supply
3.1.1 Input characteristics
Items
Condition
Spec
Note
AC Input Voltage range
AC Input Voltage rating
AC input frequency range
AC input frequency rating
AC Input Current
Universal input full range
Universal input full range
90~264Vac
90~264Vac
100~240Vac
47~63Hz
50~60Hz
2.0A(max)
0.8A(max)
35A (max)
70A(max)
≥79%
100~240Vac
100Vac
240Vac
Inrush Current
115Vac,cold star,25°C
230Vac,cold star,25°C
DC output full loading
See Note2
AC-DC power Efficiency
Note2. Before each test, the buck capacitor need to be discharged.
Before each test, it must be 10 minutes at least after the latest test.
Hot star not component be damaged.
3.1.2 Output characteristics
Items
Condition
Spec
Note
With system See note 3
Ripple and Noise
+25V output
<800mv
<500mv
<150mv
<500mv
<480mv
+5V output
USB +5V output:
Audio +5V output:
+25V output
With dummy Load
For system active
+5V output
<100mv
<100mv
<100mv
USB +5V output:
Audio +5V output:
25V loading:0.3A~1.4A
5V loading:0.75A~1.5A
Audio 5V: 0A~1.2A
USB 5V: 0A~1.5A
Vcc25V:23.2V~28V
Vcc5V: 4.75V~5.25V
Audio 5V: 4.95V~5.45V
USB 5V: 4.75V~5.25V
DC Output Voltage
25v loading:0.1A~1.5A
5V loading: 0A
Vcc25V: 23.2V~30V
Vcc5V: 4.75V~5.25V
For power saving or DC
off
Acer
Acer –LCD-D240H
DC output loading
capability
Vcc5V/1.8A,
Vcc25V/1.4A
Audio 5V: 1.5A
USB 5V: 1.5A
Rise Time
<50mS
Dynamic load change
Hold-up time
AC input: 100V~240V
>10mS
<10%
2S
Overshoot
Turn on delay time
Power management
See Table-1
Note3: Paralleled a 0.1uF ceramic Cap. And 47uF aluminum Cap. Between the end of DC loading side,
Measured band-width=20MHz. Ripple voltage of +25V is less than 1500mv when enter into burst mode.
3.1.3 Protection characteristics
Protection
OPP(Over current protection)
SCP(short circuit protection)
OVP(Over voltage protection)
OTP(Over temperature protection)
Fuse protection
Condition
Spec
nominal AC input
90W ( min )
with auto-recovery function
Auto recovery
<output capacitor voltage
NA
NA
Table-1
Status
H-sync
V-sync
Video
active
blanked
blanked
blanked
--
Power
≤ 70W
< 2W
LED
Power On
on
off
on
off
--
on
on
off
off
--
White
Amber
Amber
Amber
Off
Power Saving
Power Off
< 2W
< 2W
< 1W
3.2 Backlight Power Supply
Panel: AUO-M240HW01-V2
Items
Specification
Lamp
4 CCFL
23.2---28V
Input Voltage
Input current
1.2A (Typ.), 1.4A (Max.)
3.6V≧V on≧ 2.0 V (on)
On/Off switch level
On/Off switch level
-0.3v ≤ V off ≤ 0.8 V (off)
3.6V≧V on≧ 2.0 V (on)
-0.3v ≤ V off ≤ 0.8 V (off)
35%~100%
Brightness PWM Duty (ACM Off)
Brightness PWM Duty (ACM On)
CCFL operating Voltage
3%~100%
900Vrms (Typ.),
CCFL Current
7.5mA (Typ.)
8.0mA (Max.)
Acer
Acer –LCD-D240H
CCFL startup voltage
CCFL startup voltage
Operating frequency
Protect delay time
≧2000 Vrms (0˚C)
≧1850 Vrms (25˚C)
40~60 KHz
> 1 second
Efficiency
≥75%
Note: Other panels please refer to the reference panel specs.
Brightness output
The test to verify specifications in this section shall be performed under the following standard conditions
unless otherwise noted.
Temperature
: 25 ± 5°C
Test pattern
: white
Video Resolution
Video input level
Warm-up time
: 1920 x 1080
: 700 mV ± 2%
: 30 minutes
Set brightness control and also contrast control at maximum, to measure the screen center, the light
output shall BL ≥ 240 cd/m2 .
3.3 White balance
The test standard conditions refer to Sec 3.3. (Brightness and contrast are under default value)
Chromaticity Coordinate
Mode
x
y
Cool
Warm
User
9300K
6500K
0.283 ± 0.030
0.313 ± 0.030
Panel While x
0.297 ± 0.030
0.329 ± 0.030
Panel While y
3.4 Brightness uniformity
The test standard conditions refer to Sec 3.3.
Acer
Acer –LCD-D240H
Min. luminance of ninepoints(backlight)
≥ 75%
Max.luminance of ninepoints(backlight)
4.
Input / Output Signal Specifications
4.1 AC in
4.1.1 AC Input Voltage: 100~240VAC
4.1.2 AC Input Current: 1.2A @100Vac, 0.6A @240Vac
4.1.3 AC Frequency Range: 50~60Hz
4.2 Audio in
4.2.1 Input impedance ﹕ ≧ 10K ohm
4.2.2 Frequency response range ﹕200Hz ~ 10kHz
4.3 USB in (Option)
The USB 2.0 includes 4 pins;
pin1:VBUS;
pin2:DM;
pin3:DP;
pin4:GND
4.4 HDMI in
HDMI type A Connector Pin assignment:
19 18 17 16
13 12
15 14
11 10
9
8
7
6
5
4
3
2
1
Pin
1
2
Symbol
TMDS Data2+
TMDS Data2 shield
TMDS Data2-
Pin
11
12
13
14
15
16
17
18
19
Symbol
TMDS Clock shield
TMDS Clock-
CEC
3
4
TMDS Data1+
No connect
SCL
5
TMDS Data1 shield
TMDS Data1-
6
SDA
7
TMDS Data0+
DDC/CEC Ground
+5V Power
Hot Plug Detect
8
TMDS Data0 shield
TMDS Data0-
9
10
TMDS Clock+
Acer
Acer –LCD-D240H
4.5 DVI-D in
DVI-D Connector Pin assignment:
Pin
1
2
3
4
5
6
7
8
Symbol
TMDS Data 2-
TMDS Data 2+
Pin
16
17
18
19
20
21
22
23
24
Symbol
Hot Plug Detect
TMDS Data 0-
TMDS Data 0+
TMDS Data 0/5 shield
TMDS Data 2/4 shield
DDC Clock
DDC Data
Analog Vertical Sync
TMDS Data 1-
Clock shield
Clock +
Clock -
9
10 TMDS Data 1+
11 TMDS Data 1/3 shield
12
13
14 +5V Power
15 GND
4.6 VGA in
4.6.1 D-sub Connector Pin assignment:
Pin
1
Symbol
Red Video
2
3
4
Green Video
Blue Video
N/C
5
Ground
6
7
8
9
10
11
12
13
14
Red Ground
Green Ground
Blue Ground
PC +3.3/+5V
Sync. Ground
N/C
DDC SDA
H sync
V sync
Acer
Acer –LCD-D240H
15
DDC SCL
4.6.2 Signal SPEC:
Items
Condition
Specification
Analog RGB signal Input impedance =75 Ohm 0.7Vp-p
Sync
TTL level, Separate H/V-sync(+/-)
Input impedance ≧1k Ohm
H-Sync Frequency
V-Sync Frequency
31K~83KHz
49~76Hz
4.7 Timing table
VESA MODES
Horizontal
Vertical
Nominal
Mode
Nominal
Nominal Pixel
Clock (MHz)
Frequency
+/-0.5KHz Sync Polarity
Frequency
+/-1Hz
Sync
Polarity
Resolution
640*480@60Hz
31.469
37.861
37.5
N
N
N
P
P
P
P
N
N
P
P
P
P
P
P
P
59.941
72.809
75
N
N
N
P
P
P
P
N
N
P
P
P
P
P
P
P
25.175
31.5
31.5
36
VGA
640*480@72Hz
640*480@75Hz
800*600@56Hz
35.156
37.879
48.077
46.875
48.363
56.476
60.023
67.5
56.25
60.317
72.188
75
800*600@60Hz
40
SVGA
800*600@72Hz
800*600@75Hz
1024*768@60Hz
50
49.5
65
60.004
70.069
75.029
75
XGA
1024*768@70Hz
75
1024*768@75Hz
1152*864@75Hz
1280*960@60Hz
1280*720@60Hz
78.75
108
108
74.176
108
135
85.5
60
60
44.955
63.981
79.976
47.712
59.94
60.02
75.025
60.015
1280*1024@60Hz
SXGA
1280*1024@75Hz
WXGA
1360*768@60Hz
1440*900@60Hz
1440*900@75Hz
55.935
70.635
N
N
59.89
P
P
106.5
WXGA+
74.984
136.75
1680*1050@60Hz
65.29
N
59.954
P
146.25
WSXGA+
1680*1050@75Hz (VGA Only) 82.306
N
P
P
N
74.89
60
P
P
N
P
187.00
162
1600*1200@60Hz
75
UXGA
1920*1080(Red)@60Hz
1920*1080@60Hz (VGA Only)
66.587
67.158
59.93
59.96
138.5
173
IBM MODES
720x400@70Hz
31.469
N
70.087
P
28.322
30.24
MAC MODES
66.667
N
VGA
35
P
Acer
SVGA 832*624@75Hz
Acer –LCD-D240H
57.283
49.725
68.681
N
N
74.55
N
N
XGA
1152*870@75Hz
75.062
100
Other MODES
WXGA 1280*800@60Hz
49.702
N
59.81
P
83.5
Note: 1. Non-interlace signals only (An interlace signal cannot be display)
2. Please refer to F/W specification for more detail
3. Each frequency of Power Macintosh and Sun Ultra is a reference value
Acer
Acer –LCD-D240H
4.8 HDMI timing table
For DVD Player Input, Attached timing is supported :
Ratio
Mode
Resolution
Pixel Clock MHz
H sync KHz
V sync Hz
VGA
NTSC (480i)
NTSC (480p)
PAL (576i)
PAL (576p)
720p
640 x 480p
720 x 480
720 x 480
720 x 576
720 x 576
1280 x 720
1280 x 720
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
25.2
31.5
15.73
31.47
15.63
31.27
37.5
60
60
60
50
50
50
60
50
4:3
4:3
4:3
13.50
27.00
13.50
27.00
74.25
74.25
74.25
4:3
16:9/4:3
16:9
16:9
16:9
720p
1080i
45
28.125
1080i
74.25
148.50
148.50
33.72
56.250
67.50
60
50
60
16:9
16:9
16:9
1080P
1080P
4.9 Audio output SPEC
Specification
TYP
Items
TEST CONDITIONS
Min
1.6
3.4
MAX
Output power (W)
2.0
4
2.4
4.6
THD+N = 10%( AT 1KHz 1Vrms)
AT 1KHz 1Vrms
Output impedance (Ω)
Po≦ 2.0W(at1KHz 1Vrms,
200HZ <f<10KHZ)
Total harmonic distortion plus noise
---
---
10%
THD+N≦ 5%
Signal to noise ratio (dB)
PWM frequency (KHz)
40
---
---
200
250
300
Note: The low pass RC Filter (R=100Ω / C=0.047uF) for Class-D Output Power and THD+N Measurement
4.10 DDC data
EDID File Format : VESA’s EDID Standard Version #3, Revision #0,
EDID Structure : Version #1, Revision #3.
EDID Data Table : See the attached table (for example)
4.10.1 VGA EDID table
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
0
1
2
3
4
5
6
7
00
00
12
B3
35
30
4C
00
FF
00
50
00
00
48
1F
30
FF
01
54
01
13
0A
53
30
FF
03
AF
01
2A
20
12
30
FF
68
CF
01
21
20
00
30
FF
35
00
01
00
20
0A
30
FF
1D
81
1A
00
20
20
30
00
78
80
36
1A
20
20
30
04
EA
71
80
00
20
20
30
72
60
4F
A0
00
20
20
30
74
85
95
70
00
00
20
30
00
A6
00
38
FC
00
20
30
00
56
95
1F
00
00
00
30
00
4A
0F
40
44
FD
00
0A
00
9C
A9
30
32
00
00
00
00
25
40
20
34
38
FF
CS
Acer
Acer –LCD-D240H
4.10.2 DVI EDID table
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
0
1
2
3
4
5
6
7
00
00
12
B3
35
30
4C
00
FF
00
50
00
00
48
1F
30
FF
01
54
01
13
0A
53
30
FF
03
AF
01
2A
20
12
30
FF
80
CF
01
21
20
00
30
FF
35
00
01
00
20
0A
30
FF
1D
81
1A
00
20
20
30
00
78
80
36
1A
20
20
30
04
EA
71
80
00
20
20
30
72
60
4F
A0
00
20
20
30
74
85
95
70
00
00
20
30
00
A6
00
38
FC
00
20
30
00
56
95
1F
00
00
00
30
00
4A
0F
40
44
FD
00
0A
00
9C
A9
30
32
00
00
00
00
25
40
20
34
38
FF
CS
4.10.3HDMI EDID table
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
00 FF FF FF FF FF FF 00 04 72 74 00 00 00 00 00
00 00 01 03 80 35 1D 78 EA 60 85 A6 56 4A 9C 25
12 50 54 AF CF 00 81 80 71 4F 95 00 95 0F A9 40
B3 00 01 01 01 01 1A 36 80 A0 70 38 1F 40 30 20
35 00 13 2A 21 00 00 1A 00 00 00 FC 00 44 32 34
30 48 0A 20 20 20 20 20 20 20 00 00 00 FD 00 38
4C 1F 53 12 00 0A 20 20 20 20 20 20 00 00 00 FF
00 30 30 30 30 30 30 30 30 30 30 30 30 0A 01 95
02 03 22 F2 23 09 7F 07 4E 01 02 03 84 05 06 07
10 11 12 15 93 1F 14 83 01 00 00 66 03 0C 00 10
00 10 8C 0A D0 8A 20 E0 2D 10 10 3E 96 00 06 23
21 00 00 18 01 1D 00 72 51 D0 1E 20 6E 28 55 00
06 23 21 00 00 1E 01 1D 80 18 71 1C 16 20 58 2C
25 00 06 23 21 00 00 9E 01 1D 00 BC 52 D0 1E 20
B8 28 55 40 06 23 21 00 00 1E 01 1D 80 D0 72 1C
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
16 20 10 2C 25 80 06 23 21 00 00 9E 00 00 00
CS
4.11 DPF function
D240HsupportsDPF Function, which Embeded 2GNandflash stroage ,it can also
communication with PC by connecting USB cable,and supports 4 IN 1 memory card
which includes SD, XD, MS, and MMC, besides the 4 kind’s memory card,it also
supports the adaptor card: Mini SD, MicroSD, MS Pro,MS,Duo, MS Pro Duo, RS
MMC, MMC Plus, RS MMC,and supports CF card slot include CFI, CF II,MD memory
card.User can easily switch to different functions though OSD Menue.
4.11.1.DPF function introduce
Acer
Acer –LCD-D240H
1) Nand play photo function:
1. without any memory card, the screen will display slideshow photo from Nand storage,
2. If no photo files in Nand storage,the screen will display browser mode.
2) card reader function
Connect the USB upstream and the card read function will be started when D240H on Monitor mode..PC will find
the two USB devices are CF card and SD/MS/XD/MMC card, the two devices that in the DPF all can be operation by PC
4.11.2. Memory card test
1, Insert SD/MS/XD/MMC card, Select the memory on input source menu
2, Play photo ,the performance should be no color shift, the other function such as
Rotate,effect ,slideshow, next, forward, pause also should be passed.
Notes:
1. SD card family include mini SD, mobile SD,MMC memory card include RS MMC, RS MMC Plus, RS
MMC mobile.
2. MS card slot also support MS Pro, MS Duo, MS Pro Duo,
3. CF card slot support CFI,CF II and MD(Micro Drive) card.
4.11.3. Support format test
The D240H only support photo format as below. please check and confirm.
Acer
Acer –LCD-D240H
4.11.4. DPF function test
4.11.4.1.
DPF Monitor
flow
to DPF
Category ext
Yes/ No
keypad control
1. Switch
keypad flow
.jpg
.bmp
Photo
2. DPF play photo mode keypad flow
Acer
Acer –LCD-D240H
3. DPF select photo mode flow
4. DPF setting menu flow
Acer
Acer –LCD-D240H
Acer
Acer –LCD-D240H
Setting menu layer-1
Acer
Acer –LCD-D240H
Setting menu layer-2
Setting menu layer-3
Acer
Acer –LCD-D240H
4.11.4.2. DPF photo function test
1.Test the picture as below items:
1).Photo performance
2). Next picture
3). Forward picture
4). Pause
5). Play
6), slide show.
7). Rotate.
8). Browser small and big photo
Check and confirm the function is OK!
2.Test the setting menu as below items:
1),Slideshow time
2). Slideshow effect
3). Auto sleep time
4). Reset
5). Random paly
6), Auto copy
7). Delete all
8). Background color
9). Language
Check and confirm the function is OK!
3.Special define for DPF
1). Monitor Switch to DPF mode
2). Monitor language must sync with DPF language
3). If Auto sleep timer progress finished,DPF mode will switch monitor mode
Acer
Acer –LCD-D240H
4). If first Monitor mode switch to DPF when AC on and DC on and form power
saving ,the screen will display DPF Acer logo
5). If hot_plug any card on DPF mode,the display screen will change to input source
select mode .
6). If always press rotate key on play/back mode,the photo will rotate one time.
7). If always press left or right key on browser mode ,if photo less memory range will
show the photo else show the last photo
3.Warning message
Acer
Acer –LCD-D240H
4.11.5. DPF System Profile
1.DPF-functions overview
2.DPF-Input support& image support
Acer
Acer –LCD-D240H
5.
Function Specifications
All the tests to verify specifications in this section shall be performed under the following standard
conditions unless otherwise noted. The standard conditions are:
Temperature
: 25 ± 5°C
Warm-up time
: 30 minutes minimum
: All the specified modes
Checking display modes
5.1 Panel general specifications
5.1.1 General specifications
Item
Describe
Supplier
AUO
Model name
Display Area
Pixel Pitch
M240HW01-V0
531.36 × 298.89
276.75(Per one triad) × 276.75
Display Colors:
16.7M colors (RGB 6-bit + Hi_FRC)
Acer
Acer –LCD-D240H
6.
Function Specifications
All the tests to verify specifications in this section shall be performed under the following standard
conditions unless otherwise noted. The standard conditions are:
Temperature
: 25 ± 5°C
Warm-up time
: 30 minutes minimum
: All the specified modes
Checking display modes
5.2 Panel general specifications
5.2.1 General specifications
Item
Describe
Supplier
AUO
Model name
Display Area
Pixel Pitch
M240HW01-V0
531.36 × 298.89
276.75(Per one triad) × 276.75
Display Colors:
16.7M colors (RGB 6-bit + Hi_FRC)
A. Press “input key” one time to search (a port with signal in order)
B. Show “source icon” at the same time, as searching that port
C. Go into next port automatically, if search the port without signal
D. Display it, if search the port with signal
Input select
5.2.2 Hot Key Operation
HOT KEY OPERATION
e Color AUTO MENU ◄ ► POWER
FUNCTION
DESCRIPTION
Press [e], and then press [POWER]
for DC power on. OSD menu will be
shown with “F” on the left top. Select
“F” for entering factory mode.
FACTORY
MODE
●
ON
5.3 OSD Structure
The On-Screen Display (OSD) shall be an easy to use icon based menu through keypad OSD
buttons or remote control unit. The unit shall leave the factory with all OSD controls set to their default
values.
Control
Range
First
Second
Third
Fourth
Default Value
Picture
User
Text
Acer e color
Management
---
Standard
Standard
Graphics
Movie
---
empowering Technology
0～100
Brightness
---
User mode
77
Acer
Acer –LCD-D240H
Text mode
44
Standard mode
77
97
77
50
50
50
60
56
Graphics mode
Movie mode
User mode
Text mode
0～100
Contrast
---
---
---
---
Standard mode
Graphics mode
Movie mode
0～100
0～100
0～100
0～100
---
H. Position
V. Position
50
50
Focus
Clock
---
50 (1)
---
Warm
Cool
---
---
---
---
Color Temp
0～100
0～100
0～100
---
Red
Green
Blue
---
80
User
80
80
Auto Configure
H. Position
---
---
---
---
Depending on the keypad
position
0～100
0～100
10～120
---
---
V. Position
3
OSD Timeout
---
---
---
---
10
Full
---
---
Wide Mode
DDC/CI
Full
ON
Aspect
ON
---
---
---
---
OFF
ON
ACM
Input
OFF
---
OFF
VGA
DVI
---
---
---
---
---
---
---
---
HDMI
EMEA
NO-EMEA
English English
繁體中文
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
Russian
Deutsch Deutsch
Français Français
Español Español
Italiano Italiano
Language
English
简体中文
Dutch
日本語
Finnish
Acer
Acer –LCD-D240H
Reset
---
---
---
---
---
---
---
---
---
---
---
---
---
Resolution
H. Freq
(2)
V. Freq
---
---
Input Type
S/N
---
---
---
---
Notes: (1) Clock default 50 is for Visa timing. Others depend on timing.
(2) Depend on timing & S/N
Acer
Acer –LCD-D240H
5.4 OSD Translation
5.4.1 Monitor part
Main menu (NO_EMEA)
English
繁體中文
(英语)
Deutsch
(德语)
Français
(法语)
Español
(西班牙语) (意大利语)
Italiano
简体中文
日本語
畫面
画面
ピクチャー
輝度
Picture
Bild
Image
Imagen
Brillo
Immagine
Luminosità
Contrasto
O.Posizione
V.Posizione
Nitidezza
亮度
亮度
Brightness
Contrast
H.Position
V.Position
Focus
Helligkeit
Kontrast
H.Position
V.Position
Fokus
Luminosité
Contraste
H.Position
V.Position
Netteté
對比
对比度
水平位置
垂直位置
相位
コントラスト
水平位置
垂直位置
フェーズ
クロック
Contraste
H.Posicion
V.Posicion
Nitidez
水平位置
垂直位置
相位
時脈
时序
Clock
Takt
Fréquence
Reloj
Orologio
色溫
色温
Colour Temp
Farbtemp.
Temp. Couleur Temp. Color Temp. Colore
色溫度
暖色溫
冷色溫
使用者設定
紅色
暖色温
暖色
寒色
Warm
Cool
User
Red
Warm
Kalt
Chaud
Clair
Càlido
Frio
Caldo
冷色温
Freddo
Utente
Rossa
使用者设定 ユーザー設定
Anwender
Rot
Utilisateur
Rouge
Usuario
Rojo
红色
赤
綠色
绿色
緑
Green
Grün
Blau
Vert
Bleu
Verde
Verde
藍色
蓝色
青
Blue
Azul
Blu
自動調整
自动调整
自動調整
Auto Config
Autom. Abgl. Autoréglage
Autoajuste
Autoregolazione
OSD
OSD
OSD 顯示時
間設定
OSD 显示时 OSD 表示時間
T. de espera
OSD
OSD Timeout
Setting
OSD-Dauer Délai de l'OSD
Intervallo OSD
间设定
設定
設定
设置
設定
Einstellung
Réglages
Configuración Impostazione
寬螢幕模式
全螢幕
宽屏模式
ワイドモード
全画面
Wide Mode
Full
Vollbild
Vollbild
Plein écran
Plein écran
Completa
Completa
Schermo intero
Pieno
全屏
Aspect
Input
Aspect
輸入
输入
入力
Eingang
Sprache
Entrée
Entrada
Idioma
Input
语言
語言
言語
Language
Langue
Lingua
恢复出厂模
式
恢復出廠模式
リセット
Reset
Rücksetzen Restaurer
Reiniciar
Resetare
お待ちくださ
い
Veuillez
Bitte warten
Espere, por
favor
請稍待
请稍待
Please Wait
Attendere prego
patienter
資訊
結束調整
進入
移動
開
情報
終了
選択
移動
オン
オフ
音量
Information
Exit
Info
Informations
Quitter
Información
Salida
Informazioni
Uscita
信息
退出菜单
进入
Beenden
Eingabe
Beweg.
EIN
Enter
Move
ON
Entrez
Introducir
Mover
Invio
移动
Dépla.
Muovi
开启
Allumé
ACTIVADO
Apagado
Volumen
ATTIVA
Spento
Volume
關
关闭
OFF
Aus
OffEteinte
Volume
Volume
音量
Lautstärke
音量
Acer
Acer –LCD-D240H
Message menu: (NON_EMEA)
English
(英语)
Deutsch
(德语)
Français
(法语)
Español
(西班牙语)
Italiano
(意大利语)
繁體中文
简体中文
日本語
Autoréglage
Veuillez
patienter
Autoajuste
Espere,
porfavor
自動調整
請稍待
自动调整
请稍待
自動調整
お待ちください
Auto Config
Please Wait
Autom. Abgl.
Bitte warten
Autoregolazione
Attendere prego
ケーブルが接続
されて
いません
無訊號線
連接
信号线
无连接
Cable Not
Connected
Leitung nicht
angeschlossen
Câble non
connecté
Cable no
conectado
Cavo non
connesso
入力はサポート
されて
いません
Frequencias
no
soportadas
不支援
輸入訊號
输入
不支援
Input Not
Supported
Frequenzen nicht Fréquences non
Frequenza
non supportata
unterstützt
supportées
無訊號
无讯号
信号なし
No Signal
Kein signal
Pas de signal
Sin señal
Assenza segnale
English
Russian
Deutsch
Français
Español
Italiano
Dutch
Finnish
(英语)
(俄语)
(德语)
(法语)
(西班牙语)
(意大利语)
(荷兰语)
(芬兰语)
Picture
Изображ.
Bild
Image
Imagen
Brillo
Immagine
Beeld
Kuva
Acer
Acer –LCD-D240H
Brightness
Яркость
Helligkeit
Kontrast
Luminosité
Contraste
Luminosità
Contrasto
Helderheid Kirkkaus
Контрастно
сть
Полож. по
гориз.
Полож. по
верт.
Contrast
Contraste
H.Posicion
V.Posicion
Contrast
Kontrasti
H.Position
V.Position
H.Position
V.Position
H.Position
V.Position
O.Posizione
V.Posizione
H. positie Vaakasijainti
V. positie Pystysijainti
Фокусировк
а
Scherpstell
Tarkennus
ing
Focus
Fokus
Takt
Netteté
Nitidez
Reloj
Nitidezza
Orologio
Clock
Частота
Fréquence
Klok
Taajuus
Värin
lämpöisyys
Colour Temp
Цвет.темп. Farbtemperatur Temp. Couleur Temp. Color Temp. Colore
Kleurtemp.
Warm
Cool
User
Red
Теплый
Warm
Chaud
Clair
Càlido
Frio
Caldo
Warm
Koel
Lämmin
Viileä
Холодный Kalt
Freddo
Utente
Rossa
Пользоват. Anwender
Utilisateur
Rouge
Usuario
Rojo
Gebruiker Käyttäjä
Красный
Зеленый
Синий
Rot
Rood
Punainen
Vihreä
Green
Grün
Vert
Verde
Verde
Groen
Blauw
Blue
Blau
Bleu
Azul
Blu
Sininen
Автонастро
йка
Autom.conf Autom.
Auto Config
Autom. Abgl.
Autoréglage
Autoajuste
Autoregolazione
iguratie
asetukset
OSD
OSD
Вр. отобр.
Меню
T. de espera
OSD
Time-out
OSD
OSD Timeout
Setting
OSD-Dauer
Einstellung
Délai de l'OSD
Réglages
Intervallo OSD
Aikakatkaisu
Настр.
Configuración Impostazione
Instelling Asetus
Breedbeeld
Широкоэк.р
еж.
Modo
Wide Mode
Full
Bildformate
Vollbild
Mode Large
Plein écran
Modo Wide
panorámico
Laajakuva
modus
Полное
Completa
Pieno
Volledig
Täysikuva
Aspect
Input
Aspect
Вход
Eingang
Sprache
Entrée
Entrada
Idioma
Input
Ingang
Taal
Tulo
Kieli
Language
Язык
Langue
Lingua
Reset
Сброс
Rücksetzen
Restaurer
Reiniciar
Resetare
Opn.instellen Nollaus
Veuillez
patienter
Espere, por
favor
Een ogenblik
Odota
Please Wait
Подождите Bitte warten
Attendere prego
geduld
Информаци
я
Информаци
я
Information
Information
Info
Informations
Informations
Información Informazioni
Información Informazioni
Informatie
Informatie
Informaatio
Info
Informaatio
Exit
Выход
Ввод
Beenden
Eingabe
Beweg.
Quitter
Entrez
Dépla.
Salida
Uscita
Invio
Afsluiten
Enter
Lopeta
Syötä
Liiku
Enter
Move
Introducir
Mover
Переме
Muovi
Verpl.
PÄÄLLÄ
<ON>
ON
Вкл
EIN
Allumé
ACTIVADO
ATTIVA
AAN
OFF
Выкл
Aus
OffEteinte
Volume
Apagado
Volumen
Spento
Volume
Uit
Pois päältä
Громкость
Lautstärke
Volume
Äänenvoim.
Volume
Color management OSD (scenario OSD) language: (NON_EMEA)
English
(英语)
Deutsch
(德语)
Français
(法语)
Español
(西班牙语)
Italiano
(意大利语)
繁體中文
简体中文
日本語
Acer
Standard
Text
Acer –LCD-D240H
標準
文字
标准
標準
Standard
Text
Standard
Texte
Estándar
Texto
Standard
Testo
文本
テキスト
グラフィック
ス
圖形
图形
Graphics
Grafiken
Images
Gráficos
Grafica
電影
电影
ムービー
ユーザー
調整/終了
選択
Movie
Spielfilm
Benutzer
Film
Película
Usuario
Film
使用者
調整/結束
選擇
用户
User
Utilisateur
Utente
Abstimmen/Bee
nden
调节/退出
选取
Adjust/Exit
Select
Ajuster/Quitter Ajuste/salir
Sélectionner
Regola/Esci
Auswahl
Seleccionar Seleziona
Main menu (EMEA)
Message menu: (EMEA)
English
Russian
Deutsch Français Español
Italiano
Dutch
Finnish
(英语)
(俄语)
(德语)
(法语) (西班牙语) (意大利语)
(荷兰语)
(芬兰语)
Автонастро
йка,
подождите.. Bitte warten
.
Bezig met
Autoréglage Autoajuste
Autom.
asetukset.
Odota
Auto Config
Please Wait
Autom. Abgl.
Autoregolazione automatische
Attendere prego configuratie, een
ogenblik geduld
Veuillez
Espere, por
favor
patienter
Cable Not
Connected
Кабель не Leitung nicht
подключен angeschlossen connecté
Câble non Cable no
Cavo non
Kabel niet
aangesloten
Kaapeli ei
kiinni
conectado connesso
Вход не
поддержива nicht
ется
Frequenzen
Fréquences Frequencias
Input Not
Supported
Frequenza
non supportata ondersteund
Ingang niet
non
no
Tuloa ei tueta
Ei signaalia
unterstützt
supportées soportadas
Pas de
Sin señal
signal
Assenza
No Signal
Нет сигнала Kein signal
Geen signaal
segnale
Color management OSD(scenario OSD) language: (EMEA)
English
Russian
Deutsch
Français
Español
Italiano
Dutch
Finnish
(英语)
(俄语)
(德语)
(法语)
(西班牙语)
(意大利语)
(荷兰语)
(芬兰语)
Standard
Стандарт
Текст
Standard
Standard
Texte
Estándar
Standard
Standaard
Vakio
Text
Text
Texto
Testo
Tekst
Teksti
Изображен
ие
Graphics
Movie
Grafiken
Spielfilm
Benutzer
Images
Film
Gráficos
Película
Usuario
Grafica
Film
Grafische
Film
Grafiikka
Elokuva
Käyttäjä
Кино
Пользовате
ль
Настроить Abstimmen/Be
User
Utilisateur
Utente
Regola/Esci
Gebruiker
Aanpassen/v
erlaten
Adjust/Exit
Select
Ajuster/Quitter Ajuste/salir
Säädä/Lopeta
Valitse
/Выход
enden
Auswahl
Выбор
Sélectionner
Seleccionar Seleziona
Selecteren
6. Mechanical
6.1 Dimension
Dimension
Spec
Width
Height
Depth
574.96mm
430.29mm(W/Base), 408.11mm(W/O Base)
171.62mm(W/Base), 106.43mm(W/O Base)
Acer
Acer –LCD-D240H
Monitor Weight
5.6±0.3Kg
6.2Cabinet Material
Cabinet Material
Spec
Cabinet Plastic Material
ABS HB(PMMA)
BLACK
Front Bezel
Back Cover
Base
BLACK
BLACK
Cabinet Texture
ACER SPECIFICATION
6.3Mechanical Specification
Mechanical
Spec
Spec
≦1.3mm
Bezel Gap Specification
Screen printed Parts
Front bezel
6.4Base Mechanical Interface
items
Tilt
Compliance with TCO03, -4°(+/-1°) ~+14°(+/-1°)
Wall Mount
100mm x 100 mm
Acer
Acer –LCD-D240H
7. Package
7.1 Unit Package Specification
7.1.1 Units package
Items
Spec
Refer to ME PACKING SPEC
Packaging
Ink
COLOR
Length
632+/-2.0mm
494+/-2.0mm
139+/-2.0mm
7.9±0.3kg
Height
Width
Gross Weight
Units per Pallet
56sets/pallet
40’ /20’ Container Loading, Palletized 1120sets/560sets
7.1.2 Unit Packing Vibration
Testing with vibration shall be done in each of three mutually perpendicular axes. Axes are referenced to the
position of system as it normally sits in front of user, i.e., Front-to-back, side-to-side and top-to-bottom.
7.1.2.1 Random Vibration
Items
Sweep Frequency
Description
1~200Hz
Amplitude
1.14 Grms
Duration Time
30 minute each axis
Direction
3 mutually perpendicular axes (x, y, z)
RANDOM VIBRATION SPECTRUM BREAK POINTS
2
Frequency (Hz)
PSD, G /Hz
0.0001
0.01
1
4
100
200
0.01
0.001
Acer
Acer –LCD-D240H
7.1.3
Non operation Thermal Shock Test
Item
Description
-200C to 600C
Temperature
25ºC>60ºC (10hrs)>25ºC (2hrs)>-20ºC (10hrs)>25ºC
3cycles ,every transition time 0.5 hr,
Reset cycles times
Total cycles
3 cycles
7.1.4
Package Drop
Drop height (Select drop height according to the gross weight refer to the table at below)
1.0<W≦9.0
Gross Weight(kg)
76
Drop Height(cm)
√
Drop sequence and orientation
Drop
Drop onto
Type Drop
Corner
Edge
Edge
Edge
Flat
Figure
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6
Step 7
Corner(2-3-5)of package
Edge(3-5)
Edge(2-3)
Edge(2-5)
of package
of package
of package
Face(bottom-3)of package
Face(left-4) of package
Face(front-5) of package
Flat
Flat
Step 8
Step 9
Face(right-2) of package
Face(rear-6) of package
Flat
Flat
Step 10
Flat
Face(Top-1) of package
Mechanical and electrical damage should not exist after vibration test, and shall be submitted for approval customer before
mass production.
8. Marking and Identification
8.1S/N Label
The approval marking is required by the countries of sales destination.
8.2 Carton label
The approval marking is required by the countries of sales destination.
Acer
Acer –LCD-D240H
02. Flat Panel Specification
Product Specification
AU OPTRONICS CORPORATION
M240HW01 V2
Contents
1.0 Handling Precautions......................................................................................4
2.0 General Description ........................................................................................5
2.1 Display Characteristics ...................................................................................................... 5
2.2 Optical Characteristics....................................................................................................... 6
3.0 Functional Block Diagram ............................................................................10
4.0 Absolute Maximum Ratings..........................................................................11
4.1 TFT LCD Module..............................................................................................................11
4.2 Backlight Unit....................................................................................................................11
4.3 Absolute Ratings of Environment .....................................................................................11
5.0 Electrical characteristics ..............................................................................12
5.1 TFT LCD Module............................................................................................................. 12
5.1.1 Power Specification................................................................................................... 12
5.1.2 Signal Electrical Characteristics ................................................................................ 13
5.2 Backlight Unit................................................................................................................... 14
6.0 Signal Characteristic.....................................................................................16
6.1 Pixel Format Image ......................................................................................................... 16
6.2 The input data format ...................................................................................................... 16
6.3 Signal Description............................................................................................................ 17
6.4 Timing Characteristics ..................................................................................................... 18
6.5 Timing diagram................................................................................................................ 19
6.6 Power ON/OFF Sequence............................................................................................... 20
7.0 Connector & Pin Assignment .......................................................................21
7.1 TFT LCD Module............................................................................................................. 21
7.1.1 Pin Assignment.......................................................................................................... 21
7.2 Backlight Unit................................................................................................................... 22
7.2.1 Signal for Lamp connector......................................................................................... 22
8.0 Reliability Test...............................................................................................23
9.0 Shipping Label...............................................................................................24
10.0 Mechanical Characteristics ........................................................................25
document version 1.0
2
Product Specification
AU OPTRONICS CORPORATION
M240HW01 V2
1.0 Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard
surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth
when handling.
7) Do not open or modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it was taken
out from the container, do not press the center of the CCFL reflector edge. Instead, press at
the far ends of the CCFL Reflector edge softly. Otherwise the TFT Module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the
Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure, do not twist nor bend the TFT Module
even momentary. At designing the enclosure, it should be taken into consideration that no
bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT
Module may be damaged.
12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow
local ordinances or regulations for disposal.
13) Small amount of materials having no flammability grade is used in the LCD module. The LCD
module should be supplied by power complied with requirements of Limited Power Source
(IEC60950 or UL1950), or be applied exemption.
14) The LCD module is designed so that the CCFL in it is supplied by Limited Current Circuit
(IEC60950 or UL1950). Do not connect the CCFL in Hazardous Voltage Circuit.
document version 1.0
4
Product Specification
AU OPTRONICS CORPORATION
M240HW01 V2
2.0 General Description
This specification applies to the 24 inch-wide Color a-Si TFT-LCD Module M240HW01.The
display supports the Full HD - 1920(H) x 1080(V) screen format and 16.7M colors (RGB 6-bits +
Hi-FRC data). All input signals are 2-channel LVDS interface and this module doesn’t contain an
inverter board for backlight.
2.1 Display Characteristics
The following items are characteristics summary on the table under 25℃ condition:
ITEMS
Screen Diagonal
Active Area
Unit
[mm]
[mm]
SPECIFICATIONS
609.7(24.0”)
531.36 (H) x 298.89 (V)
1920(x3) x 1080
Pixels H x V
Pixel Pitch
[um]
276.75 (per one triad) ×276.75
R.G.B. Vertical Stripe
TN Mode, Normally White
Pixel Arrangement
Display Mode
White Luminance ( Center )
[cd/m2]
300 cd/m2 (Typ.)
Contrast Ratio
1000 (Typ.)
Optical Response Time
Nominal Input Voltage VDD
Power Consumption
(VDD line + CCFL line)
Weight
[msec]
[Volt]
[Watt]
5ms (Typ., on/off)
+5.0 V
35 W (Typ.)
(without inverter, all black pattern)
[g]
2755 (Typ.)
Physical Size
Electrical Interface
Support Color
Surface Treatment
Temperature Range
Operating
[mm]
556.0 (W) x 323.2 (H) x 16.35 (D) typ
Dual channel LVDS
16.7M colors (RGB 6-bit + Hi_FRC )
Anti-Glare, 3H
[oC]
[oC]
0 to +50
-20 to +60
Storage (Shipping)
RoHS Compliance
RoHS Compliance
document version 1.0
5
Product Specification
AU OPTRONICS CORPORATION
M240HW01 V2
2.2 Optical Characteristics
The optical characteristics are measured under stable conditions at 25℃:
Item
Unit
Conditions
Min.
Typ.
Max.
Note
-
-
Horizontal (Right)
150
170
CR = 10
(Left)
Viewing Angle
Contrast ratio
[degree]
2
-
-
Vertical
CR = 10
(Up)
(Down)
140
600
160
Normal Direction
1000
-
3
4
-
-
-
Raising Time (TrR)
Falling Time (TrF)
Raising + Falling
3.5
1.5
5
7.5
2.5
10
Response Time
[msec]
Red x
0.619
0.308
0.259
0.579
0.116
0.649
0.338
0.289
0.609
0.146
0.679
0.368
0.319
0.639
0.176
Red y
Green x
Green y
Blue x
Color / Chromaticity
Coordinates (CIE)
5
Blue y
0.040
0.283
0.299
250
0.070
0.313
0.329
300
0.100
0.343
0.359
-
White x
White y
Color Coordinates (CIE) White
Central Luminance
[cd/m2]
[%]
6
7
Luminance Uniformity
75
80
-
Crosstalk (in 60Hz)
Flicker
1.5
8
9
[%]
-20
dB
document version 1.0
6
Product Specification
AU OPTRONICS CORPORATION
M240HW01 V2
Note 1: Measurement method
The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt
temperature change during measuring (at surface 35℃). In order to stabilize the luminance, the
measurement should be executed after lighting Backlight for 30 minutes in a stable, windless and
dark room.
Photo detector
Measured distance
LCD Panel
TFT-LCD Module
Center of the screen
Note 2: Definition of viewing angle measured by ELDIM (EZContrast 88)
Viewing angle is the measurement of contrast ratio ≧10, at the screen center, over a 180°
horizontal and 180° vertical range (off-normal viewing angles). The 180° viewing angle range is
broken down as follows; 90° (θ) horizontal left and right and 90° (Φ) vertical, high (up) and low
(down). The measurement direction is typically perpendicular to the display surface with the
screen rotated about its center to develop the desired measurement viewing angle.
documen
7
Product Specification
AU OPTRONICS CORPORATION
M240HW01 V2
Note 3: Contrast ratio is measured by TOPCON SR-3
Note 4: Definition of Response time measured by Westar TRD-100A
The output signals of photo detector are measured when the input signals are changed from “Full
Black” to “Full White” (rising time, TrR), and from “Full White” to “Full Black” (falling time, TfF),
respectively. The response time is interval between the 10% and 90% (1 frame at 60 Hz) of
amplitudes.
%
Tr
Tr
F
R
100
90
Optical
White
Black
White
Black
response
10
0
1 Frame
1 Frame
TrR + TfF = 5 msec (typ.).
Note 5: Color chromaticity and coordinates (CIE) is measured by TOPCON SR-3
Note 6: Central luminance is measured by TOPCON SR-3
Note 7: Luminance uniformity of these 9 points is defined as below and measured by
TOPCON SR-3
Minimum Luminance in 9 points (1- 9)
Uniformity =
Maximum Luminance in 9 Points (1- 9)
Note 8: Crosstalk is defined as below and measured by TOPCON SR-3
document version 1.0
8
Product Specification
AU OPTRONICS CORPORATION
M240HW01 V2
CT = | YB – YA | / YA × 100 (%)
Where
YA = Luminance of measured location without gray level 0 pattern (cd/m2)
YB = Luminance of measured location with gray level 0 pattern (cd/m2)
Note 9: Test Patern: Subchecker Pattern measured by TOPCON SR-3
R G B R G B
Gray Level = L127
R G B R G B
Gray Level = L0
R G B R G B
Method: Record dBV & DC value with TRD-100
Amplitude
AC
DC
Time
AC Level(at 30 Hz)
Flicker (dB) = 20log
DC Level
document version 1.0
9
Product Specification
AU OPTRONICS CORPORATION
M240HW01 V2
3.0 Functional Block Diagram
The following diagram shows the functional block of the 24.0 inch Color TFT-LCD Module:
LVDS
I/F PCB Interface:
JAE FI-XB30SSL-HF15
STM MSBKT2407P30HB
Mating Type:
FI-X30HL (Locked Type)
document version 1.0
10
Product Specification
AU OPTRONICS CORPORATION
M240HW01 V2
4.0 Absolute Maximum Ratings
Absolute maximum ratings of the module are as following:
4.1 TFT LCD Module
Item
Symbol
Min
Max
Unit
Conditions
Logic/LCD Drive
Voltage
VDD
0
6.0
[Volt]
Note 1,2
4.2 Backlight Unit
Item
Symbol
Min
Max
Unit
Conditions
3.0
8.0
CCFL Current
ICFL
[mA] rms
Note 1,2
4.3 Absolute Ratings of Environment
Item
Symbol
Min.
0
Max.
Unit
Conditions
Operating Temperature
Operation Humidity
Storage Temperature
Storage Humidity
TOP
HOP
TST
HST
+50
90
[oC]
[%RH]
[oC]
5
Note 3
-20
5
+60
90
[%RH]
Note 1: With in Ta (25℃)
Note 2: Permanent damage to the device may occur if exceeding maximum values
Note 3: For quality perfermance, please refer to AUO IIS(Incoming Inspection Standard).
Operating Range
Storage Range
document version 1.0
11
Product Specification
AU OPTRONICS CORPORATION
M240HW01 V2
5.0 Electrical characteristics
5.1 TFT LCD Module
5.1.1 Power Specification
Input power specifications are as following:
Symbol
Parameter
Min
Typ
Max
Unit
Conditions
Logic/LCD Drive
Voltage
VDD
5.0
[Volt] +/-10%
4.5
5.5
VDD= 5.0V,All black Pattern,
At 60Hz
VDD= 5.0V,All black Pattern,
At 60Hz
IDD1
Input Current
-
-
0.6
1.2
[A]
PDD1
IRush
VDD Power
3
-
6
3
[Watt]
[A]
Inrush Current
Note 1
-
-
Allowable Logic/LCD
Drive Ripple Voltage
VDD= 5.0V, All Black Pattern
At 75Hz
VDDrp
-
300
[mV] p-p
Note 1: Measurement conditions:
The duration of rising time of power input is 470 us.
+5.0V
Q3
AO6402
D6
D5
D2
D1
F1
S
VCC
R1
47K
(LCD Module Input)
C1
1uF/16V
(High to Low)
Control
Signal
Q3
AO6402
R2
G
1K
C3
+12.0V
SW1
SW MAG-SPST
VR1
47K
0.01uF/25V
C2
1uF/25V
document version 1.0
12
Product Specification
AU OPTRONICS CORPORATION
M240HW01 V2
5.1.2 Signal Electrical Characteristics
Input signals shall be low or Hi-Z state when VDD is off. Please refer to specifications of
SN75LVDS82DGG (Texas Instruments) in detail.
Characteristics of each signal are as following:
Symbol
Parameter
Differential Input High
Threshold
Min
Typ
Max
Units
Condition
VICM = 1.2V
VTH
-
+50
+100
[mV]
Note 1
Differential Input Low
Threshold
VICM = 1.2V
Note 1
VTL
│VID│
VICM
-100
100
-50
-
-
[mV]
[mV]
[V]
Input Differential Voltage
Differential Input Common
Mode Voltage
600
+1.5
Note 1
VTH-VTL = 200MV (max)
Note 1
+1.0
+1.2
Note 1: LVDS Signal Waveform
document version 1.0
13
Product Specification
AU OPTRONICS CORPORATION
M240HW01 V2
5.2 Backlight Unit
Parameter guideline for CCFL Inverter is under stable conditions at 25℃ (Room Temperature):
Parameter
Min.
Typ.
Max.
Unit
Note
CCFL Standard Current (ISCFL)
7.0
7.5
8.0
[mA] rms
7.5
CCFL Operation Current (IRCFL)
[mA] rms
2
3.0
8.0
CCFL Frequency (FCFL)
40
2000
1850
-
53
-
60
-
[KHz]
3, 4
CCFL Ignition Voltage (ViCFL, Ta= 0℃)
CCFL Ignition Voltage (ViCF, Ta= 25℃)
CCFL Operation Voltage (VCFL)
CCFL Power Consumption (PCFL)
[Volt] rms
[Volt] rms
[Volt] rms
[Watt]
5
-
-
900
(@7.5mA)
-
6
7
-
27
-
50,000
CCFL Life Time (LTCFL)
-
[Hour]
40,000
Note 1: Typ. values are AUO recommended design values.
*1 All of characteristics listed are measured under the condition using the AUO test inverter.
*2 It is recommended to check the inverter carefully. Sometimes, interfering noise stripes
appear on the screen, and substandard luminance or flicker at low power may happen.
*3 While designing an inverter, it is suggested to check safety circuit very carefully. Impedance
of CCFL, for instance, becomes more than 1 [M ohm] when CCFL is damaged.
*4 Generally, CCFL has certain delay time after applying kick-off voltage. It is recommended to
keep on applying kick-off voltage for 1 [Sec] until discharge.
*5 Reducing CCFL current will increase CCFL discharge voltage and generally increases CCFL
discharge frequency. So all the parameters of the inverter should be carefully designed so
the inverter will not produce too much leakage current from high-voltage output.
*6 Both CCFLs in the CCFL set (2 CCFL lamps on each side of a panel) is designed for
identical phase driving. Reversed phase driving of CCFL set is not encouraged.
*7 For designing CCFL current, it is highly recommanded to use symmetric and consistent
sinusoidal wave for each CCFL input current with asymmetric ration of 10% or less in both
postive area and negative area (ie. 0.9*√2*Irms < I1 & I2 < 1.1*√2*Irms) as refer to the
following diagram, otherwise proper CCFL functionality cannot be guarantied.
document version 1.0
14
Product Specification
AU OPTRONICS CORPORATION
M240HW01 V2
Note 2: CCFL standard current is measured at 25±2℃.
Note 3: CCFL discharge frequency should be carefully determined to avoid interference between
inverter and TFT LCD.
Note 4: The frequency range will not affect lamp life and reliability characteristics.
Note 5: CCFL inverter should be able to release power that has generating capacity exceeding
2000 volt. Lamp units need minimum voltage, 2000 Volt, for ignition.
Note 6: The variance of CCFL power consumption is ±10%. (IRCFL × VCFL × 4 = PCFL)
Note 7: Definition of life time: brightness becomes 50%. The minimum life time of CCFL unit is on
the condition of 7.5mA CCFL current and 25±2℃.
document version 1.0
15
Product Specification
AU OPTRONICS CORPORATION
M240HW01 V2
6.0 Signal Characteristic
6.1 Pixel Format Image
Following figure shows the relationship of the input signals and LCD pixel format.
1
2
1919 1920
R G B R G B
R G B R G B
1st Line
R G B R G B
R G B R G B
1080 Line
6.2 The input data format
Note 1: R/G/B data 7:MSB, R/G/B data 0:LSB
O = “Odd Pixel Data” E = “Even Pixel Data”
document version 1.0
16
Product Specification
AU OPTRONICS CORPORATION
M240HW01 V2
6.3 Signal Description
The module using one LVDS receiver SN75LVDS82(Texas Instruments). LVDS is a
differential signal technology for LCD interface and high speed data transfer device. LVDS
transmitters shall be SN75LVDS83(negative edge sampling). The first LVDS port(RxOxxx)
transmits odd pixels while the second LVDS port(RxExxx) transmits even pixels.
PIN #
SIGNAL NAME
RxOIN0-
RxOIN0+
RxOIN1-
RxOIN1+
RxOIN2-
RxOIN2+
GND
DESCRIPTION
Negative LVDS differential data input (Odd data)
Positive LVDS differential data input (Odd data)
Negative LVDS differential data input (Odd data)
Positive LVDS differential data input (Odd data)
Negative LVDS differential data input (Odd data, DSPTMG)
Positive LVDS differential data input (Odd data, DSPTMG)
Power Ground
1
2
3
4
5
6
7
8
9
RxOCLK-
RxOCLK+
RxOIN3-
RxOIN3+
RxEIN0-
RxEIN0+
GND
Negative LVDS differential clock input (Odd clock)
Positive LVDS differential clock input (Odd clock)
Negative LVDS differential data input (Odd data)
Positive LVDS differential data input (Odd data)
Negative LVDS differential data input (Even data)
Positive LVDS differential data input (Even data)
Power Ground
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
RxEIN1-
RxEIN1+
GND
Positive LVDS differential data input (Even data)
Negative LVDS differential data input (Even data)
Power Ground
RxEIN2-
RxEIN2+
RxECLK-
RxECLK+
RxEIN3-
RxEIN3+
GND
Negative LVDS differential data input (Even data)
Positive LVDS differential data input (Even data)
Negative LVDS differential clock input (Even clock)
Positive LVDS differential clock input (Even clock)
Negative LVDS differential data input (Even data)
Positive LVDS differential data input (Even data)
Power Ground
NC
No connection (for AUO test only. Do not connect)
No connection (for AUO test only. Do not connect)
Power +5V
NC
VDD
VDD
Power +5V
VDD
Power +5V
VDD
Power +5V
document version 1.0
17
Product Specification
AU OPTRONICS CORPORATION
M240HW01 V2
Note1: Start from left side
Note2: Input signals of odd and even clock shall be the same timing.
6.4 Timing Characteristics
Basically, interface timing described here is not actual input timing of LCD module but close to
output timing of SN75LVDS82DGG (Texas Instruments) or equivalent.
Item
Symbol
Min
Typ
Max
Unit
Data CLK
Tclk
40
75
90
[MHz]
Period
Th
1034
960
74
1060
960
100
1120
1080
40
2047
960
[Tclk]
[Tclk]
[Tclk]
[Th]
H-section
V-section
Display Area Tdisp(h)
Tblk(h)
Tv
Blanking
Period
1087
2047
1080
967
1088
1080
8
Display Area Tdisp(v)
[Th]
Tblk(v)
F
Blanking
Frame Rate
[Th]
50
60
75
[Hz]
Note : DE mode only
document version 1.0
18
Product Specification
AU OPTRONICS CORPORATION
M240HW01 V2
6.5 Timing diagram
Tv
M pixel
Tblk(v)
Tdisp(v)
Y
Th
X
DE
2
3
4
N
1
N
Invalid Data
Invalid Data
RGB Data
Line
Line
Line
Line
Line
Line
CLK
Tclk
Th
Tdisp(h)
Tblk(h)
DE
RGB Data Pixel Pixel Pixel Pixel
(Odd)
Pixel Pixel Pixel Pixel Pixel Pixel
11
Pixel Pixel Pixel
M-5 M-3 M-1
Pixel Pixel
Invalid Data
Invalid Data
Invalid Data
Invalid Data
M-7 M-5 M-3 M-1
1
3
5
7
9
1
3
RGB Data Pixel Pixel Pixel Pixel
(Even)
Pixel Pixel Pixel Pixel Pixel Pixel
10 12
PixelPixel Pixel
M-4 M-2 M
Pixel Pixel
M-6 M-4 M-2 M
2
4
6
8
2
4
document version 1.0
19
Product Specification
AU OPTRONICS CORPORATION
M240HW01 V2
6.6 Power ON/OFF Sequence
VDD power and lamp on/off sequence are as follows. Interface signals are also shown in the
chart. Signals from any system shall be Hi-Z state or low level when VDD is off.
Value
Parameter
Unit
Min.
0.5
0
Typ.
Max.
10
15
-
T1
T2
T3
T4
T5
T6
T7
-
-
[msec]
[msec]
[msec]
[msec]
[msec]
[msec]
[msec]
300
200
0
-
-
-
16
-
50
100
-
-
1000
-
document version 1.0
20
Product Specification
AU OPTRONICS CORPORATION
M240HW01 V2
7.0 Connector & Pin Assignment
Physical interface is described as for the connector on module. These connectors are capable of
accommodating the following signals and will be following components.
7.1 TFT LCD Module
Connector Name / Designation
Interface Connector / Interface card
STM
JAE
Manufacturer
MSBKT2407P30HB
FI-XB30SSL-HF15
Type Part Number
Mating Housing Part Number
FI-X30HL (Locked Type)
7.1.1 Pin Assignment
Pin#
Signal Name
RxOIN0-
Pin#
Signal Name
RxOIN0+
1
3
2
4
RxOIN1-
RxOIN1+
5
RxOIN2-
GND
6
RxOIN2+
RxOCLKIN-
RxOIN3-
RxEIN0-
GND
7
8
9
RxOCLKIN+
RxOIN3+
RxEIN0+
RxEIN1-
GND
10
12
14
16
18
20
22
24
26
11
13
15
17
19
21
23
25
RxEIN1+
RxEIN2-
RxECLKIN-
RxEIN3-
GND
RxEIN2+
RxECLKIN+
RxEIN3+
NC (for AUO test only. Do not
connect)
NC (for AUO test only. Do not
connect)
27
29
VDD
28
30
VDD
VDD
VDD
document version 1.0
21
Product Specification
AU OPTRONICS CORPORATION
M240HW01 V2
7.2 Backlight Unit
Physical interface is described as for the connector on module. These connectors are capable of
accommodating the following signals and will be following components.
Connector Name / Designation
Lamp Connector / Backlight lamp
CVILUX
Manufacturer
CP0502SL090
CP0502P1ML0
Type Part Number
Mating Type Part Number
7.2.1 Signal for Lamp connector
Connector No.
CN1
Pin No.
Input
Hot1
Color
Pink
Function
1
2
1
2
High Voltage
Low Voltage
High Voltage
Low Voltage
Cold1
Hot2
White
Blue
Upper
Lower
CN2
Cold2
Black
Connector No.
CN3
Pin No.
Input
Hot1
Color
Pink
Function
1
2
1
2
High Voltage
Low Voltage
High Voltage
Low Voltage
Cold1
Hot2
White
Blue
CN4
Cold2
Black
document version 1.0
22
Product Specification
AU OPTRONICS CORPORATION
M240HW01 V2
8.0 Reliability Test
Environment test conditions are listed as following table.
Items
Required Condition
Note
Temperature Humidity Bias (THB)
Ta= 50℃, 80%RH, 300hours
High Temperature Operation (HTO) Ta= 50℃, 50%RH, 300hours
Low Temperature Operation (LTO) Ta= 0℃, 300hours
High Temperature Storage (HTS)
Low Temperature Storage (LTS)
Ta= 60℃, 300hours
Ta= -20℃, 300hours
Acceleration: 1.5 Grms
Vibration Test
Wave: Random
(Non-operation)
Frequency: 10 - 200 Hz
Duration: 30 Minutes each Axis (X, Y, Z)
Acceleration: 50 G
Wave: Half-sine
Shock Test
Active Time: 20 ms
(Non-operation)
Direction: ±X, ±Y, ±Z (one time for each Axis)
Drop Test
Height: 46 cm, package test
Thermal Shock Test (TST)
On/Off Test
-20℃/30min, 60℃/30min, 100 cycles
On/10sec, Off/10sec, 30,000 cycles
1
2
Contact Discharge: ± 8KV, 150pF(330Ω ) 1sec,
15 points, 25 times/ point.
ESD (Electro Static Discharge)
Altitude Test
Air Discharge: ± 15KV, 150pF(330Ω ) 1sec
15 points, 25 times/ point.
Operation:10,000 ft
Non-Operation:30,000 ft
Note 1: The TFT-LCD module will not sustain damage after being subjected to 100 cycles of rapid
temperature change. A cycle of rapid temperature change consists of varying the temperature from
0℃
0℃
to 6 , and back again. Power is not applied during the test. After temperature cycling, the
-2
unit is placed in normal room ambient for at least 4 hours before power on.
Note 2: EN61000-4-2, ESD class B: Certain performance degradation allowed
No data lost
Self-recoverable
No hardware failures.
document version 1.0
23
Product Specification
AU OPTRONICS CORPORATION
M240HW01 V2
9.0 Shipping Label
The label is on the panel as shown below:
Note 1: For Pb Free products, AUO will add
for identification.
Note 2: For RoHS compatible products, AUO will add
for identification.
for identification.
Note 3: For China RoHS compatible products, AUO will add
Note 4: The Green Mark will be presented only when the green documents have been ready by
AUO Internal Green Team.
document version 1.0
24
10.0 Mechanical Characteristics
Ver 0.2
Ver 0.2
Ver 0.2
Acer
Acer –LCD-D240H
03 Exploded Diagram
3.1 D240H_SCREW_LIST
Q'T
Y(P
CS)
Fixed
ITEM
PN
Description
Remark
For
T(kg*cm)
6.5±0.5
12±1
509146306 SCREW,P,CROSS,W/WAS,
200R M3*6,Zn-Cc
509216608 SCREW,F,CROSS,M4*8,BL
110R ACK,NL,ROHS(NYLOK)
509412610 SCREW B CROSS T T-4*10
500R
509000000
700R
1
2
3
4
10
4
NVBD/PWRBD/HDMI
For Hingle toBack cover
For Hingle to Stand Front
For D-SUB CON&DVI
9.5±0.5
4.0±0.25
3
BLK ROHS
BOLT,#4-40x11.8,Ni
4
3.2. LCD Exploded drawing (All)
Acer
Acer –LCD-D240H
04 Troubleshooting
4.1 Black Sreen
Black Screen
Check power supply:
Pin 3, 4 of CN101
NG
POWER Fail
OK
Check power supply:
For U102
Check U101,
U106
NG
NG
NG
OK
Check reset:
pin114 of U102
Check C125,
R133
OK
Check Crystal waveform
Pin 116,117 of U102
Check X101, C126,
C114,R134
OK
OK
OK
Check CCFL_Enable
Pin 100 of U102
Check Pin 105 of
CN102
Inverter Fail
NG
NG
U102 fail
Acer
Acer –LCD-D240H
4.2 Bad Screen
Bad Screen
Check LVDS
cable
OK
OK
OK
Workmanship
NG
Change LVDS
cable
LVDS cable NG
NG
Check Crystal:
Pin 114,126 of
U102
Check the pins
of U102
NG
Change X101, C114,
C126
Acer
Acer –LCD-D240H
4.3 White Sreen
White Screen
Check LVDS
Cable Insert OK?
OK
Workmanship
LVDS cable NG
Panel NG
NG
OK
Change LVDS
Cable
NG
OK
NG
Check VLCD is
+5V?
Check LVDS cable
OK
NG
NG
Check Panel
Enable of U102
U102 Fail
OK
Check Q101,
Q104, Q102, R160,
R162，R157
NG
Q101, Q104, Q102,
R160, R162，R157 fail
05 Spare parts List
82424173A120R
CN
ACER PART NO. OEM PART NO
DESCRIPTION
55.LJR0J.001
55.LJR0J.002
792381300720H PCBA,IF/B(V2,W /SPK,EM EA),LP2441-737
792381400710H PCBA,PI/B,W /SPK,LP2441-737
55.LEW 0J.003
55.LEW 0J.004
55.LJR0J.003
792381500000R PCBA,POW ER KEYPAD/B,LP2441ROHS
792381500010R PCBA,TOUCHPAD BOARD,LP2441ROHS
792382400700H PCBA,CARD BOARD,LP2441-737
50.LEW 0J.002
50.LEW 0J.003
430303002230R HRN LVDSFFC 30P166.5mm W /TASTE
430300400390R HRN ASS'Y 4P27M M UL1571#28
50.LE40J.001
50.LJR0J.001
430300802060R HRN ASSY,2X4PTO 1X8P,220mm,UL1571#28
430303003060R HRN LVDSFFC 30P190mm W /CORE&TASTE
50.LJR0J.002
430306000010R HRN FFC 60P50mm 0.5PitchW /TASTE
27.LBN0J.001
50.LA10J.003
50.LBQ0J.001
50.L63VF.003
453070801190R PW RCORD 16A/250V BLK 6FT VDE/KTL H05VV-F
453030300370R CABLE,DVI-D 18+1PM ALE 6FT BLACK ,ROHS
453010100380R CABLE,D-SUB 15PM ALE 6FT BLACK/BLUE,ROH
453030300120R CABLE AUDIO 1P6FT BLACK/GREEN CP03B06P0
60.LJR0J.001
714050021202R ASSY,BACKCOVER,DPF,LP2441
60.LEW 0J.002
60.LEW 0J.003
714030022100R ASSY BEZEL ,LP2441
714011206200R ASSY STAND ,LP2441
60.LEW 0J.004
60.LJR0J.002
714020018200R ASSY BASE,LP2441
701000018401R ASSY CHASSIS,DPF,LP2441
60.LEW 0J.005
60.LEW 0J.006
501020228600R HINGE COVER,LEFT ,LP2441
501020228601R HINGE COVER,RIGHT ,LP2441
23.LFV0J.001
618100200430R SPEAKER 2.5W 4Ω 230mm&210mm R/G/B W /CASE
LK.24005.019
LK.24005.019
631102240240H LCP24"M 240HW 01-V2-00(A)(AUO)HF
631102240250H LCP24"M 240HW 01-V2-0A(A)(AUO)HF
Acer
Acer –LCD-D240H
06 Schematics and Layouts
6.1 IF BD Layout
Acer
Acer –LCD-D240H
6.2 Power BD Layout
Acer
Acer –LCD-D240H
Acer
Acer –LCD-D240H
6.3 Keypad BD Layout
Acer
Acer –LCD-D240H
6.4 Touchpad BD Layout
6.5 Card BD Layout
Acer
Acer –LCD-D240H
6.5Switching Mode Power Supply circuit
5
4
3
2
1
CF33V
sd/ms/xd_33V
CN302
CN303
CF/MD
SD0_CD
SD0_D2
SD0_D3
1
2
3
4
5
6
7
8
9
SD (CD)
SD (DAT2)
SD (DAT3)
SD (CMD)
SD (GND)
SD (VCC)
SD (CLK)
SD (GND)
SD (DAT0)
SD (DAT1)
SD (WP)
CF_D0
CF_D1
CF_D2
CF_D3
CF_D4
CF_D5
CF_D6
CF_D7
CF_D8
CF_D9
CF_D10
CF_D11
CF_D12
CF_D13
CF_D14
CF_D15
21
22
23
2
3
4
D0
D1
D2
D3
D4
D5
D6
D7
SD0_CMD
R302
R303
0
0
pull up
STORAGE_PWE
MS_D0
MS_D1
GPC13
GPC14
GPC15
pull down
pull down
SD0_CLK
MS_D0
MS_D1
SD0/XD_D0
MS_D_0
R304
R305
220
220
MS_D_1
SD0_D0 xD_D0
SD0_D1 xD_D1
SD0_D2 xD_D2
SD0_D3 xD_D3
MMC_D4 xD_D4
MMC_D5 xD_D5
MMC_D6 xD_D6
MMC_D7 xD_D7
SD0_D0
SD0_D1
SD0_WP
5
6
pull down
pull down
GPF9
GPF10
XD_ALE/C
XD_CLE/C
SD0/XD_D1
10
11
CN304
MS_D2
MS_D3
MS_D4
MS_D5
MS_D6
MS_D7
SD0/MS/XD_D2
SD0/MS/XD_D3
SD0/MS/XD_D4
SD0/MS/XD_D5
SD0/MS/XD_D6
SD0/MS/XD_D7
47
48
49
27
28
29
30
31
D8
D9
GPI8
GPI9
GPI10
GPF27
GPF25
GPF23
GPF21
GPF19
GPF17
GPF16
GPF14
GPF12
GPF10
GPC12
GPC10
GPC8
1
3
5
7
9
2
4
6
8
D
C
B
A
D
C
B
A
1
3
5
7
2
4
6
8
D10
D11
D12
D13
D14
D15
GPF11
GPF20
XD_REN/C
XD_WEN/C
GPF26
GPF24
GPF22
GPF20
GPF18
GPC13
GPF15
GPF13
GPF11
GPF9
GPC11
GPC9
GPC7
GPC5
GPC3
GPC1
GPC0
GPC15
GPF7
pull up
pull up
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
9
10
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
11 12
13 14
15 16
17 18
19 20
21 22
23 24
25 26
27 28
29 30
31 32
33 34
35 36
37 38
39 40
41 42
43 44
45 46
47 48
49 50
51 52
53 54
55 56
57 58
59 60
GPF15
GPF16
XD_BSY/C
XD_WPn/C
SD0_CLK MS_CLK
SD0/MS_CLK
R306
C302
0
pull down
CF_DA0
CF_DA1
CF_DA2
20
19
18
17
16
15
14
12
11
10
8
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
5p/50V/NC
12
13
14
15
16
17
18
19
20
21
MS (GND)
MS (VCC)
MS (SCLK)
MS (DATA3)
MS (CD)
MS (DATA2)
MS (DATA0)
MS (DATA1)
MS (BS)
GPF18
GPF21
XD_CE0
XD_CD
pull up
pull up
MS_CLK
MS_D3
MSINS#
MS_D2
MS_D_0
MS_D_1
MS_BS
GPC12
MS_INS
GPC6
GPC4
GPC2
GPC14
GPF6
GPF4
GPF2
GPF0
MS (GND)
CF_CS0
CF_CS1
GPF5
GPF3
GPF1
7
32
CS0
CS1
SYS_33V
22
23
40
33
PAD0
PAD1
VS2#
VS1#
CF_CD1
CF_CD0
25
26
CD2
CD1
24-1
24-2
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
XD (GND)
XD (CD)
XD (R/B)
XD (RE)
XD (CE)
XD (CLE)
XD (ALE)
XD (WE)
XD (WP)
XD (GND)
XD (D0)
XD (D1)
XD (D2)
XD (D3)
XD (D4)
XD (D5)
XD (D6)
XD (D7)
XD (VCC)
xD_CD
9
34
35
36
39
41
42
43
44
45
46
24
37
ATASEL#
IORD#
IOWR#
WE#
CSEL#
RESET#
IORDY
INPACK#
REG#
DASP#
PDIAG#
IOCS16#
INTRQ
xD_BSY
XD_REN
xD_CE
xD_CLE
xD_ALE
XD_WEN
XD_WPn
CF_DIOR
CF_DIOW
CF33V
CON30X2/2mm
R307
0
CF_RST
CF_IORDY
CF_DMARQ
CF_DMACK
xD_D0
xD_D1
xD_D2
xD_D3
xD_D4
xD_D5
xD_D6
xD_D7
XD 8Bit Out
MS & SD 8Bit/4Bit Out
FB303
R340
R341
R342
4
3
2
0
0
220
220
330 x4 RN2 pull
330 x4 RN4
CF_INTRQ
GPC0
GPC1
GPC2
GPC3
SD0/MS_CLK(O)
SD0_CMD/MS_BS(O)
SD0/XD_D0(IO)
SD0/XD_D1(IO)
SD0/MS/XD_D2(IO)
SD0/MS/XD_D3(IO)
SD0/MS/XD_D4(IO)
SD0/MS/XD_D5(IO)
220 SD0/MS/XD_D6(IO)
SD0/MS/XD_D7(IO)
SD0_CD(I)
SD0/MS_CLK
SD0_CMD/MS_BS
SD0/XD_D0
SD0/XD_D1
SD0/MS/XD_D2
SD0/MS/XD_D3
SD0/MS/XD_D4
SD0/MS/XD_D5
SD0/MS/XD_D6
SD0/MS/XD_D7
SD0_CD
upGPF17
GPF22
CF_IORDY(I)
CF_DIOR(O)
CF_DIOW(O)
CF_INTRQ(I)
CF_DA0(O)
CF_DA1(O)
CF_DA2(O)
CF_RST(O)
CF_IORDY
CF_DIOR
CF_DIOW
CF_INTRQ
CF_DA0
CF_DA1
CF_DA2
4
3
2
1
1
2
3
4
5
6
7
8
8
7
6
5
GPF23
GPF26
GPC1
GPF24
GPF25
GPF27
pull down
220x4 RN3 GPC4
5
6
7
8
pull down
GPC5
GPC6
GPC7
GPC8
GPC9
GPC10
GPC11
pull down
CF_RST
1
R343
GPI9
GPI10
CF_DMACK
CF_DMARQ
RUICONN_4N1
R344
upR345
upR346
220
0
0
R308
R309
0/NCCF_DMACK(O)
CF_DMARQ(I)
pull
pull
0
SD0_WP(I)
SD0_WP
SYS_33V
CF 16 Bit I/F
DC5V
CF 16Bit
CF_CS1
CF_CS0
R310
R311
10K
10K
CN305
UB111234K5
sd/ms/xd_33V
GPF0
GPF1
GPF2
GPF3
GPF4
GPF5
GPF6
GPF7
CF_D8(IO)
CF_D8
CF_D9
330 x4 RN6
F301
R312
6V/0.75A
0
4
3
2
1
4
3
2
1
5
6
7
8
5
6
7
8
CF_33V
CF_D9(IO)
CF_D10(IO)
CF_D11(IO)
CF_D12(IO)
CF_D13(IO)
CF_D14(IO)
CF_D15(IO)
SYS_33V
CF_D10
CF_D11
CF_D12
CF_D13
CF_D14
CF_D15
GPC10 SD0_CD
GPC11 SD0_WP
UHDM20
Q301
AP2305GN
R313
R314
10K/NC
10K/NC
FB301
300Ω 2A
2
3
GPF18 XD_CE
330 x4 RN7
330 x4 RN8
330 x4 RN9
R315
R316
R318
10K
L301
GPF20 XD_WEN
GPF15 NF/xD_BSY
10K/NC
10K/NC
NC/20mH
+
GPC2
GPC3
GPC4
GPC5
GPC6
GPC7
GPC8
GPC9
CF_D0(IO)
CF_D1(IO)
CF_D2(IO)
CF_D3(IO)
CF_D4(IO)
CF_D5(IO)
CF_D6(IO)
CF_D7(IO)
CF_D0
CF_D1
CF_D2
CF_D3
CF_D4
CF_D5
CF_D6
CF_D7
GPF12 NF_WEN
GPF11
R319
R320
10K
10K
4
3
2
1
4
3
2
1
5
6
7
8
5
6
7
8
NF_REN/XD_REN
UHDP20
R321
R322
R323
0
15K/NC
15K/NC
GPF10 NF_CLE/XD_CLE(O)
STORAGE_PWE R301
1K
R324
R325
R327
R329
10K
GPF16 NF_WPn/XD_WPn(I)
GPC1
GPF9
10K/NC
10K/NC
10K/NC
SD0_CMD/MS_BS/CF_DA0(O)
upGPI8
upGPF19
CF_CD0(I)
CF_CD1(I)
CF_CD0
CF_CD1
NF_ALE/XD_ALE(O)
pull
pull
R326
R328
330
330
GPF9
GPF10
CF_CS0(O)
CF_CS1(O)
CF_CS0
CF_CS1
R330
R331
330
330
SYS_33V
CF_33V
CF33V
Q302
AP2305GN
xD_CD
xD_CE
XD_CD
XD_CE0
FB302
300Ω 2A
2
3
SD0_CMD MS_BS
SD0_CMD/MS_BS
R332
220
xD_ALE
xD_CLE
XD_ALE/C
XD_CLE/C
SD0_WP
SD0_CD
SD0_WP/C
SD0_CD
R333
R334
22
22
XD_REN
XD_WEN
XD_WPn
XD_REN/C
XD_WEN/C
XD_WPn/C
R335
R336
R337
22
22
22
MSINS#
MS_INS
C317
DC5V
CF_CD1
CF_CD0
xD_BSY
XD_BSY/C
Near in Chip
for noise
issue
CN301
4P 2.0mm 90°
R347
R348
0
0
R338
22
R350
1K
0.01/25V
1
2
3
4
UHDP20
UHDM20
NAND Power Control Not Useing in NAND Boot Mode
InnoLux
H234H + DPF
Document Number :
???
SIZE :
APPRO BY :
A2
TITLE :
CHECK BY :
DRAWN BY :
Card interface
DATE :
SHEET
2009-03-23
OF
Rev :
V01
2
2
5
4
3
2
1
07 Assembly and Disassembly
S1: Take out a panel
S3: Take out a chassis on the panel and assemble
the power board and the chassis
S4: Take out the main board and insert the FFC
cable and keypad cable.
S2: Assemble the panel and the bezel.
S7: Use a screwdriver to screw the 4 screws to
fix the main board and USB board.
S5: Assemble the main board and the Card
board with the chassis.
MAIN BOARD
Card BOARD
2
3
1
4
S8: Use a screwdriver to screw the 1
screw to fix the HDMI connecter.
S6: Use a screwdriver to screw the 5 screws to
fix the power board.
4
5
1
5
3
2
S9: Use a screwdriver to screw the 4 screws
to fix the VGA and DVI connecter.
S11: Set up the speaker.
Red left and
green right
2
3
1
4
S12: Set up the keypad board and the
touchpad board.
S10: Fix the chassis in the bezel.
S13: Fix the touchpad board and the keypad
board. Connect the two board
S15: Assemble the stand and fix it.
1
2
4
3
S14: Assemble the back cover.
S16: Assemble the left and right hinge
cover.
1
1
2
2
3
3
4
4
S17: Assemble the base with the
stand.
|