Sony Ericsson CDP CX220 User Manual

CDP-CX220

SERVICE MANUAL

US Model

Canadian Model

AEP Model

UK Model

E Model

Australian Model

Model Name Using Similar Mechanism

CD Mechanism Type

CDP-CX250

CDM-40B

Base Unit Type

KSM-213BKN/M-N

KSS-213B/S-N

Optical Pick-up Type

SPECIFICATIONS

General

Compact disc player

Power requirements

Laser

Semiconductor laser (λ = 780 nm)

Where purchased

USA/Canada

Australia

Power requirements

Emission duration: continuous

Max 44.6 µW*

120 V AC, 60 Hz

Laser output

240 V AC, 50/60 Hz

220 V – 230 V AC, 50/60 Hz

* This output is the value measured at

a distance of 200 mm from the

objective lens surface on the

Optical Pick-up block with 7 mm

aperture.

Europe

Other countries

110 V – 120 V or 220 V – 240 V AC,

adjustable, 50/60 Hz

Power consumption

Dimensions (approx.)

(w/h/d)

12 W

Frequency response

Signal-to-noise ratio

Dynamic range

20 Hz to 20 kHz ± 0.5 dB

More than 105 dB

More than 98 dB

When the front cover is closed

430 × 200 × 480 mm (17 × 7 ⁷/8 × 19 in.)

incl. projecting parts

Mass (approx.)

9.5 kg (21 lbs)

Harmonic distortion

Channel separation

Outputs

Less than 0.0045%

More than 97 dB

Supplied accessories

Audio cord (2 phono plugs – 2 phono plugs) (1)

Remote commander (remote) (1)

Sony SUM-3 (NS) batteries (2)

CD booklet holders (2) and label (1)

Jack

type

Maximum

output

level

Load impedance

Design and specifications are subject to change without notice.

LINE OUT

Phono

Jacks

Over 10 kilohms

(at 50 kilohms)

DIGITAL

OUT

Optical

output

–18 dBm

Wave length: 660 nm

(OPTICAL) connector

COMPACT DISC PLAYER

MICROFILM

SECTION 1

SERVICING NOTES

SAFETY CHECK-OUT

NOTES ON HANDLING THE OPTICAL PICK-UP

BLOCK OR BASE UNIT

After correcting the original service problem, perform the follow-

ing safety check before releasing the set to the customer:

Check the antenna terminals, metal trim, “metallized” knobs,

screws, and all other exposed metal parts for AC leakage.

Check leakage as described below.

The laser diode in the optical pick-up block may suffer electro-

static break-down because of the potential difference generated

by the charged electrostatic load, etc. on clothing and the human

body.

During repair, pay attention to electrostatic break-down and also

use the procedure in the printed matter which is included in the

repair parts.

The flexible board is easily damaged and should be handled with

care.

LEAKAGE

The AC leakage from any exposed metal part to earth ground and

from all exposed metal parts to any exposed metal part having a

return to chassis, must not exceed 0.5 mA (500 microampers.).

Leakage current can be measured by any one of three methods.

1. A commercial leakage tester, such as the Simpson 229 or RCA

WT-540A. Follow the manufacturers’instructions to use these

instruments.

NOTES ON LASER DIODE EMISSION CHECK

The laser beam on this model is concentrated so as to be focused

on the disc reflective surface by the objective lens in the optical

pick-up block. Therefore, when checking the laser diode emis-

sion, observe from more than 30 cm away from the objective lens.

2. A battery-operated AC milliammeter. The Data Precision 245

digital multimeter is suitable for this job.

3. Measuring the voltage drop across a resistor by means of a

VOM or battery-operated AC voltmeter. The “limit” indica-

tion is 0.75 V, so analog meters must have an accurate low-

voltage scale. The Simpson 250 and Sanwa SH-63Trd are ex-

amples of a passive VOM that is suitable. Nearly all battery

operated digital multimeters that have a 2VAC range are suit-

able. (See Fig. A)

LASER DIODE AND FOCUS SEARCH OPERATION

CHECK

Carry out the “S curve check” in ”CD section adjustment” and

check that the S curve waveform is output repeatedly.

To Exposed Metal

Parts on Set

voltmeter

(0.75 V)

0.15 µF

1.5 k

Ω

Earth Ground

Fig. A. Using an AC voltmeter to check AC leakage.

SAFETY-RELATED COMPONENT WARNING!!

ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!

COMPONENTS IDENTIFIED BY MARK ! OR DOTTED

LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS

AND IN THE PARTS LIST ARE CRITICAL TO SAFE

OPERATION. REPLACE THESE COMPONENTS WITH

SONY PARTS WHOSE PART NUMBERS APPEAR AS

SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-

LISHED BY SONY.

LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE !

SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE

DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ

DE FONCTIONNEMENT. NE REMPLACER CES COM-

POSANTS QUE PAR DES PIÈCES SONY DONT LES

NUMÉROS SONT DONNÉS DANS CE MANUEL OU

DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.

– 3 –

CD-TEXT TEST DISC

This unit is able to display the test data (character information) written in the CD on its fluorescent indicator tube.

The CD-TEXT TEST DISC (TGCS-313:4-989-366-01) is used for checking the display.

To check, perform the following procedure.

Checking Method:

1. Turn ON the power, set the disc on the disc table with the side labeled as “test disc” as the right side, close the front cover, and chuck the

disc.

2. Press the · button and play back the disc.

3. The following will be displayed on the fluorescent indicator tube.

Display : 1kHz/0 dB/ L&R

4. Press the ≠ and ± buttons to switch the track. The text data of each track will be displayed.

For details of the displayed contents for each track, refer to “Table 1 : CD-TEXT TEST DISC TEXT Data Contents” and “Table 2 : CD-

TEXT TEST DISC Recorded Contents and Display”.

Restrictions in CD-TEXT Display

In this unit, some special characters will not be displayed properly. These will be displayed as a space or a character resembling it. For

details, refer to “Table 2 : CD-TEXT DISC Recorded Contents and Display”.

Table 1 : CD-TEXT TEST DISC TEXT Data Contents (TRACKS No. 1 to 41:Normal Characters)

TRACK

No.

TRACK

No.

Displayed Contents

1kHz/-90dB/L&R

Displayed Contents

1kHz/0dB/L&R

20Hz/0dB/L&R

40Hz/0dB/L&R

100Hz/0dB/L&R

200Hz/0dB/L&R

500Hz/0dB/L&R

1kHz/0dB/L&R

5kHz/0dB/L&R

7kHz/0dB/L&R

10kHz/0dB/L&R

16kHz/0dB/L&R

18kHz/0dB/L&R

20kHz/0dB/L&R

1kHz/0dB/L&R

1kHz/-1dB/L&R

1kHz/-3dB/L&R

1kHz/-6dB/L&R

1kHz/-10dB/L&R

1kHz/-20dB/L&R

1kHz/-60dB/L&R

1kHz/-80dB/L&R

Infinity Zero w/o emphasis//L&R

Infinity Zero with emphasis//L&R

400Hz+7kHz(4:1)/0dB/L&R

400Hz+7kHz(4:1)/-10dB/L&R

19kHz+20kHz(1:1)/0dB/L&R

19kHz+20kHz(1:1)/-10dB/L&R

100Hz/0dB/L*

1kHz/0dB/L*

10kHz/0dB/L*

20kHz/0dB/L*

100Hz/0dB/R*

1kHz/0dB/R*

10kHz/0dB/R*

20kHz/0dB/R*

100Hz Squer Wave//L&R

1kHz Squer Wave//L&R

1kHz w/emphasis/-0.37dB/L&R

5kHz w/emphasis/-4.53dB/L&R

16kHz w/emphasis/-9.04dB/L&R

NOTE: The contents of Track No. 1 to 41 are the same as those of the current TEST DISC-their titles are displayed.

– 4 –

Table 2: CD-TEXT TEST DISC Recorded Contents and Display

(In this unit, some special characters cannot be displayed. This is no a fault.)

TRACK

Recorded Contents

No.

Display

! ” # $ % & ´

(21h to 27h)1kHz 0dB L&R N All the same

( ) + , – . /

(28h to 2Fh)

(30h to 37Fh)

(38h to 3Fh)

(40h to 47Fh)

(48h to 4Fh)

(50h to 57Fh)

(58h to 5Fh)

(60h to 67Fh)

(68h to 6Fh)

(70h to 77Fh)

(78h to 7Fh)

(A0h to A7h) 8859-1

(A8h to AFh)

(B0h to B7h)

(B8h to BFh)

(C0h to C7Fh)

(C8h to CFh)

(D0h to D7Fh)

N All the same

0 1 2 3 4 5 6 7

8 9 : ; < = > ?

@A B C D E F G

H I J K L M N O

P Q R S T U VW

X Y Z [ ¥ ] ^ _

PQ R S T U VW (50h to 57h)

XY Z [ \ ] ^ _ (58····

a b c d e f g

a b c d e f g (60h to 67h)

′

h i j k l m n o

p q r s t u v w

N All the same

p q r s t u v w (70h to 77h)

x y z { I }

x y z {

} ~

(78····

i ¢ £ ¤ ¥

–

i ¢ £ ¤ ¥ § (A0···· is not displayed

–

≥C ª

≥

(A8···· C ª

P R are not displayed

•

µ ¶ •

′ ^µ• (B0···· ^•±

¶ are not displayed

′

†

¿ (B8····¹

are not displayed

À Á Â Ã Ä ÅÆÇ

È É Ê Ë Ì Í Î Ï

D Ñ Ò Ó ÔÕ Ö

ÀÁ Â Ã Ä ÅÆÇ (C0h to C7h)

N All the same

D ÑÒÓ Ô Õ Ö

(D0h to D7h)

Ø Ù Ú Û Ü Y

(D8h to DFh)

(E0h to E7h)

(E8h to EFh)

(F0h to F7Fh)

(F8h to FFFh)

Ù Ú Û Ü Y ß (D8····

à á â ã ä å æ ç (E0h to E7h)

N All the same

à á â ã ä å æ ç

è é ê ë ì í î ï

∂ ñ ò ó ô õ ö ÷

ø ù ú û ü y´

No.66

No.67

ñ ò ó ô õ ö ÷ (F0h to F7h)

ø ù ú û ü y ÿ (F8h to FFh)

N All the same

No.99

N All the same

– 5 –

SECTION 2

GENERAL

LOCATION OF PARTS AND CONTROLS

Front Panel

!¡

!º

!™

!£

STANDBY

1/u

DISC/CHARACTER

INPUT

MEMO SEARCH

PUSH ENTER

CONTINUE SHUFFLE PROGRAM REPEAT

TIME/TEXT

AMS

CHECK

CLEAR

OPEN/CLOSE

GROUP

GROUP FILE

!¢

@º

!ª

!•

!¶

!§

!∞

1 I/u (power switch) button

2 CONTINUE button

3 SHUFFLE button

4 Display window

!¡ ≠/± buttons

!™ JOG dial (DISC/CHARACTER/PUSH ENTER knob)

!£ CHECK button

!¢ CLEAR button

5 PROGRAM button

6 REPEAT button

!∞ p button

!§ P button

7 TIME/TEXT button

8 Front cover

!¶ · button

!• § (OPEN/CLOSE) button

!ª GROUP FILE button

@º GROUP 1 – 8 buttons

9 MEMO SEARCH button

!º INPUT button

– 6 –

SECTION 3

DISASSEMBLY

Note: Follow the disassembly procedure in the numerical order given.

CASE

1 four screws

3 Remove the case to

(case 3 TP2)

direction of arrow A.

1 five screws

(case 3 TP2)

2 Open the case.

FRONT PANEL SECTION

1 flat wire (CN501)

6 Remove the door (CD) ass’y

to direction of arrow A.

2 four screws

(BVTP3 × 8)

4 claw

5 front panel section

3 five screws (BVTT3 × 6)

– 7 –

GUIDE ASS’Y

3 three screws

(BVTT3 × 6)

4 boss

5 guide ass’y

3 three screws

2 screw

(PSW3 × 6)

(BVTT3 × 6)

1 connector

(CN503)

REAR PANEL SECTION

3 three connectors

(CN504, 506, 507)

1 connector

(CN505)

2 flat wire

(CN502)

6 rear panel section

4 five screws

(BVTT3 × 6)

1 connector

(CN904)

3 four screws

(PTTWH3 × 6)

5 PC board

holder

7 four screws

(BVTT3 × 6)

8 bracket

– 8 –

MECHANISM DECK

2 mechanism deck

1 three screws

(BVTT3 × 8)

1 six screws

(BVTT3 × 8)

BASE UNIT

1 screw (BVTT3 × 8)

2 fulcrum plate

(BU upper) ass’y

3 base unit

– 9 –

SECTION 4

TEST MODE

DISPLAY CHECK MODE

With the power turned off (standby state), press the I/u button

while pressing the P (pause) button.

All FL segments and grids light up together with the · (play),

P (pause), and standby LEDs.

At the same time, the GROUP LEDs are scanned one by one.

KEY AND FLUORESCENT DISPLAY TUBE CHECK

MODE

1. Connect the test point (TP:AFADJ) of the MAIN board to the

Ground, and insert the power plug to the outlet to set this mode.

First, the external SRAM is checked, and if abnormal, “SRAM

NG” is displayed.

If OK, the following steps are performed.

Note: To exit this mode, press the p (stop) button.

* Fluorescent Display Tube Check Mode

The whole fluorescent display tube lights up when the con-

nection in step 1 is made.

ADJ MODE

1. Turn ON the power of the unit, set disc to disc table, and per-

form chucking.

* Key Check Mode

2. Disconnect the power supply plug from the outlet.

3. To setADJ mode, connect the test point (TP:ADJ) of the MAIN

board to Ground, and connect the power supply plug to the

outlet.

This mode is set when a button is pressed after the whole

fluorescent display tube lights.

All buttons have a button number.

When a button is pressed, the counter display is counted up,

and the number of that button is displayed.

However, the counter display will only count up to 26, but

the number of buttons pressed will always be displayed.

The power will turn on automatically, and the first track will be

played.

In this mode, table rotation and loading operations are not per-

formed because it is taken that the disc has already been chucked.

Note: The same operations are also performed in the following when the

test point (TP: ADJ) is connected to Ground after turning on the

power.

• Direct search (movement of sledding motor) is not performed

during accessing

Counter display

Button number display

• Ignored even when GFS becomes L

• Ignored even when the Q data cannot be read

• Focus gain does not decrease

Buttons and Corresponding Button Numbers

• Spindle gain does not decrease

• Servo related settings can be set manually and checked (Refer

to ADJ Mode Special Functions Table)

Button

CLEAR

Button Number or Display

CHECK

± (AMS)

≠ (AMS)

PUSH ENTER

ADJ Mode Special Functions Table

(The buttons shown with ( ) function by using the sup-

plied remote commander only)

(OPEN/CLOSE)

INPUT

Button

Button Number or Display

Servo average display

Displays VC, FE, RF, TE and traverse in hexadecimal

numbers

CONTINUE

MEMO SEARCH 11

I/u

TIME/TEXT

GROUP FILE

GROUP 8

GROUP 7

GROUP 6

GROUP 5

REPEAT

PROGRAM

SHUFFLE

CONTINUE

GROUP 4

GROUP 3

GROUP 2

GROUP 1

SHUFFLE

Focus bias display

Each time this is pressed, the focus bias is switched

between 1 and 2

Bias actually set Optimum bias Minimum jitter

U:Upper aliasing bias L:Lower aliasing bias

PROGRAM

Auto gain display

Displays focus, tracking, sledding in hexadecimal

numbers

GROUP 1 (1) Increases the focus bias in 8 steps.

GROUP 2 (2) Sets the focus bias in the middle of aliasing.

GROUP 3 (3) Turns off the tracking and sledding servo

GROUP 4 (4) Returns the auto gain to the initial value (30)

GROUP 5 (5) Turns off the focus servo

GROUP 6 (6) Decreases the focus bias in 8 steps.

GROUP 7 (7) Re-adjusts the focus bias

All lit (LED lit)

Partial lighting 1 (LED lit)

Partial lighting 2

GROUP 8 (8) Turns on the tracking and sledding servo

(9)

Switches the focus servo gain between normal and down

FG. norm: normal, FG. down: down

DISC/

Partial lighting 3

CHARACTER

•

When the jog dial is rotated to the right, the

GROUP LEDs light up in the order of 1 → 2..8

→ 2nd → 1.

When the jog dial is rotated to the left, the

GROUP LEDs light up in the order of 8 → 7..1

→ 2nd → 8.

(10/0)

Sets the focus bias to 0 (no bias)

Next, displays the jitter measured at the focus bias set

CHECK

CLEAR

S-curve observation mode

•

Automatic eccentric measurement

The results of measurement is displayed in mm directly.

– 10 –

Partial lighting 1

AGING MODE

• Mode which repeatedly changes and plays back discs automati-

cally in the unit.

• It will repeat aging as long as no errors occur.

• If an error occurs during aging, it will stop all servos, motors,

etc. instantaneously, display the error number, and stop opera-

tions. However, the stopping conditions differ according to

whether the unit is equipped with the “self-protection function

during errors” described later.

A B C D E F G

Partial lighting 2

The function serves to maintain the state of the unit when errors

occur.

Sequence of Aging Mode

Order of Disc Change

(1 cycle takes 3 minutes)

1. Disc change

Partial lighting 3

1. No. 40

2. Load in

2nd

2. No. 120

3. TOC read

*: Counter displayed

3. No. 80

4. Access of last track

Test Points Location:

4. No. 200

[MAIN BOARD] – Component Side –

5. 3 second playback

5. No. 160

IC502

6. Access of first track

(AFADJ)

7. 3 second playback

(ADJ)

IC506

IC501

8. Load out

CN509

CN508

Special Functions in Aging Mode

1. Disc setting mode:

5 discs are set before setting the aging mode. This mode makes

the setting of these discs more easy.

2. Self protection function during errors:

Function which voluntarily corrects errors which occur dur-

ing normal operations by retries.

If this function is not provided, all operations will be stopped

without retiring. It is suitable for checking errors with low re-

producibility.

If this function is provided, and errors can be corrected by

retries, aging will be continued without stopping.

3. Aging cycle count function:

Functions which displays the number of agings carried out on

the Fluorescent indicator tube in numbers. One aging cycle

consists of five discs.

number of agings

1DISC

CD1

DISC

*DISC-40*

– 11 –

Aging Method

1. Change the [COMMAND MODE] switch (S901) on set to

[CD1].

2. Turn ON the power of the unit. Open the front cover.

3. Press the [AGING START] button of the remote commander

for aging mode (J-2501-123-A).

4. When the disc set mode is set, the · and P LEDs blink.

5. Rotate the JOG dial. The slits (No. 40, 80, 120, 160, 200) for

setting the discs will come forward. Insert the discs into these

slits. Do not set the discs in other slits.

6. Set whether the self-protection function during errors is

equipped with the unit. Press the [REPEAT] button. If “RE-

PEAT” is displayed on the Fluorescent indicator tube, it means

the function is provided. If “REPEAT” is not displayed, it

means the function is not provided.

7. Press the · button.

8. The · LED blinks, the aging mode is set, and aging is

started.

9. The aging cycle lasts 3 minutes. If errors occur during aging,

the error number will be displayed on the Fluorescent indica-

tor tube. (Refer to the following table for the details of the

errors.)

10. Aging will be repeated as long as no errors occur.

11. After each aging cycle, the number displayed on the Fluores-

cent indicator tube will increase.

12. To end aging, press the I/u button

Error Display

1 2 0

E r r 0 1

Disc number Error code

Error code

Code number

Err 01

Name

DISC sensor check 1

DISC sensor check 2

Table operation check 1

Table operation check 2

Loading operation check 1

Loading operation check 2

BU related check 1

Contents

No disc in the specified slit

Disc in other slits

Err 02

Err 03

Err 04

Err 05

Err 06

Err *1

Err *2

Err *3

Err *4

Err *5

Err *6

Err *7

Table motor current over

No table sensor input

Load in timeover

Load out timeover

Access timeover

BU related check 2

High speed search NG

Q data read error

BU related check 3

BU related check 4

BU operation (from focus search to until signal can be read) timeover

GFS monitor error

BU related check 5

BU related check 6

Focus cannot be imposed by focus search

Auto focus bias adjustment cannot be performed

BU related check 7

The * numbers mean the following according to the state of the unit during aging

2 : From checking to end of TOC read

3 : From end of TOC read to end of last track playback

4 : From end of last track playback to end of first track playback

– 12 –

SECTION 5

MECHANICAL ADJUSTMENTS

Perform the following steps before carrying out adjustments.

1. Turn ON the power of the unit, set disc to disc table No. 92,

and perform chucking.

2. Turn OFF the power.

3. Remove the case.

4. While pressing the [STOP] button, turn ON the I/u button.

The test mode is set.

5. The I/u button LED (STANDBY) starts blinking.

(Test mode)

LED (STANDBY)

1/u

STOP button

1/u button

Note 1: The cam will start rotating when the [GROUP 1] or [GROUP 5]

button is pressed continuously in the test mode.

GROUP 1

button

GROUP 5

button

GROUP 1 button

GROUP 5 button

Note 2: If the power cannot be supplied, the cam can be rotated by rotat-

ing the pulley with your finger.

cam

pulley

– 13 –

GUIDE (DISC T) ALIGNMENT

holder (guide T)

cam

fixed screw

guide (disc T)

(1) Rotate the cam and adjust to the posi-

tion shown in the figure.

guide (disc T)

(2) Check that the state is as shown in

the figure.

disc

tapering screwdriver

guide (disc T)

disc

holder (guide T)

(4) Move the holder (guide T) with a tapering screwdriver,

and set the position of the guide (disc T) to A:B=1:1.

holder

(guide T)

(3) Loosen the fixed screw by about 60 °.

– 14 –

HOLDER (DISC A2) ALIGNMENT

cam

holder (disc A2)

cam

thrust

screw

(1) Rotate the cam and adjust to the position

shown in the figure.

disc

0 – 1 mm

holder (disc A2)

(2) Check that the state is as shown in

the figure.

disc

holder (disc A2)

thrust

screw

(3) After applying suitable locking compound to the

the disc.

part, rotate the thrust screw until the holder (Disc A2) comes to the center of

– 15 –

SENSOR ALIGNMENT

Perform this adjustment after the “holder (disc A2) adjustment”.

If the disc table swings to the left and right just before the disc is

chucked, perform the following adjustment.

cam

lever (stopper) ass’y

cam

(1) Rotate the cam and adjust to the position

bracket (sensor)

shown in the figure.

table ass’y

(2) Check that the lever (stopper) ass’y secures

the disc table as shown in the figure.

disc table

swing

lever (stopper) ass’y

(4) Moving the disc table right and left with a hand after the

screw is fixed, the table will move by the play of a disc table.

If the LEDs light up alternately, the adjustment will be per-

formed correctly.

tapering screwdriver

LUMINOUS board

bracket (sensor)

PAUSE button

PLAY button

fixed screw

(3) Loosen the fixed screw by 60° to 90°, and use a tapering screwdriver to adjust the screw as shown in the figure.

Move the bracket (sensor) with the tapering screwdriver little by little, and fix the fixed screw at where the play button's LED (green)

is switched to the pause button's LED (orange) (or its reverse).

– 16 –

PULLY AND DISC CENTER HOLE ALIGNMENT

base unit

cam

bracket

(BU adjustment)

(1) Rotate the cam and adjust to the position

shown in the figure.

magnet ass’y

(2) Check that the state is as shown

in the figure.

0.5 – 2 mm

disc

disc pulley

disc hole

base unit

Note: The disc should not

be fixed.

holder (disc A2)

fixed screw

bracket

(BU adjustment)

tapering screwdriver

magnet ass’y

(4) Loosen the fixed screw by 60° to 90°, and move and adjust

the bracket (BU adjustment) up and down using a tapering

screwdriver so that the positions of the disc hole and disc

pulley become A=B or between A:B=2:1 and 1:2.

(3) Remove the Magnet ass’y.

– 17 –

MAGNET ASS’Y ALIGNMENT

cam

adjustment

screw

magnet ass’y

(1) Rotate the cam and adjust to the position

shown in the figure.

disc

magnet holder

magnet ass’y

adjustment

screw

(3) Apply suitable locking compaund to the

justing.

part after ad-

adjustment

screw

(2) Rotate the adjustment screw until A=B or between A:B=2:1

and 1:2

– 18 –

SECTION 6

ELECTRICAL ADJUSTMENTS

Note: A clear RF signal waveform means that the shape “◊” can be clearly

Note:

distinguished at the center of the waveform.

1. CD Block is basically designed to operate without adjustment. There-

fore, check each item in order given.

RF signal waveform

2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated.

3. Use an oscilloscope with more than 10MΩ impedance.

4. Clean the object lens by an applicator with neutral detergent when the

signal level is low than specified value with the following checks.

VOLT/DIV: 200 mV

TIME/DIV: 500 ns

S-Curve Check

+0.25

–0.20

level: 1.2

Vp-p

oscilloscope

BD board

TP (FE1)

TP (VC)

–

E-F Balance Check

oscilloscope

Procedure :

BD board

1. Connect oscilloscope to test point TP (FE1) on BD board.

2. Connect test point TP (ADJ) on MAIN board to ground with

lead wire.

TP (TE)

TP (VC)

–

3. Turn I/u button on to set the ADJ mode.

4. Put disc (YEDS-18) in and playback.

Press the [CHECK] button.

5. Check the oscilloscope waveform (S-curve) is symmetrical be-

tween A and B. And confirm peak to peak level within 3 ± 1

Vp-p.

Procedure :

1. Connect oscilloscpe to test point TP (TE) on BD board.

2. Connect the test point TP (ADJ) on MAIN board to the ground

with a lead wire.

3. Turn the I/u button on to set the ADJ mode.

4. Put disc (YEDS-18) in to play the number five track.

5. Press the [GROUP 3] button. (The tracking servo and the sled-

ding servo are turned OFF.)

S-curve waveform

symmetry

6. Check the level B of the oscilliscope's waveform and the A

(DC voltage) of the center of the Traverse waveform.

Confirm the following :

within 3 ± 1 Vp-p

A/B x 100 = less than ± 22%

Traverse waveform

Center of the waveform

6. After check, remove the lead wire connected in step 2.

Note: • Try to measure several times to make sure than the ratio of A : B

or B : A is more than 10 : 7.

•

Take sweep time as long as possible and light up the brightness

to obtain best waveform.

A (DC voltage)

0 V

RF Level Check

level: 1.3 ± 0.6 Vp-p

oscilloscope

(AC range)

7. Press the [GROUP 8] button. (The tracking servo and sled-

ding servo are turned ON.) Confirm the C (DC voltage) is

almost equal to the A (DC voltage) is step 6.

BD board

TP (RFO)

TP (VC)

–

Traverse waveform

Procedure :

1. Connect oscilloscope to test point TP (RFO) on BD board.

C (DC

voltage)

2. Turn I/u button on.

0 V

3. Put disc (YEDS-18) in to play the number five track.

4. Confirm that oscilloscope waveform is clear and check RF sig-

nal level is correct or not.

Tracking servo

Sled servo

OFF

Tracking servo

Sled servo

8. Disconnect the lead wire of TP (ADJ) connected in step 1.

– 19 –

RF PLL Free-run Frequency Check

Procedure:

Procedure :

1. Connect the oscilloscope to Pins 1, 2, and 4 of CN506 of

the MAIN board. Also connect a 1 kΩ resistor to Pin 4 at the

same time. (Connection 1)

1. Connect frequency counter to test point TP (XPCK) with lead

wire.

2. Check that no discs are loaded in the unit, and press the

I/u button while pressing the [INPUT] button.

3. The rotary table will continue rotating in the clockwise direc-

tion.

4. Observe the waveform at that time on the oscilloscope.

5. Loosen the screw securing the LUMINOUS board slightly.

6. Slide the LUMINOUS board to the left and right so that the

peak of the D0 waveform is at the center between the descend-

ing point of the T1 waveform and ascending point of the T2

waveform. (Waveform 1) After adjusting, apply locking com-

pound.

frequency counter

BD board

–

TP (XPCK)

2. Turn I/u button on.

3. Put the disc (YEDS-18) in to play the number five track.

Confirm that reading on frequency counter is 4.3218MHz.

Disc Sensor Adjustment

Perform this adjustment after completing all adjustments of the

mechanism section.

If not performed accurately, the presence of the disc may not be

detected properly.

Connection 1:

oscilloscope

CN506 of MAIN board

T1: Pin 1 (T. SENS 1)

T2: Pin 2 (T. SENS 2)

D0: Pin 4 (D. SENS)

–

LUMINOUS board

1 k Ω

Waveform 1:

7. Disconnect the resistor connected to Pin 4 of CN506 of the

MAIN board. (Connection 2)

8. Observe the waveform on the oscilloscope. (Waveform 2)

9. Adjust RV501 of the MAIN board so that the waveform on the

oscilloscope satisfies the following adjustment value.

10. After the adjustment, load a disc only in slit 1, close the front

cover, and press the I/u button to turn off the power.

11. Press the

button while pressing the [PUSH ENTER] button

I/u

to turn on the power.

12. If the rotary table makes round, and “YES” is displayed on the

fluorescent indicator tube after it stops, it means that the ad-

justment has been performed properly.

Connection 2:

Adjustment value:

oscilloscope

CN506 of MAIN board

T1: Pin 1 (T. SENS 1)

T2: Pin 2 (T. SENS 2)

D0: Pin 4 (D. SENS)

At the shoulder part of waveform D1, T1 becomes H and T2 be-

comes L, and at the same time, the Y width must not be smaller

than 1/4 of the Z width.

In order to satisfy this value more easily, adjust so that X=Y ap-

proximately and observe the deviation of the waveform.

–

Waveform 2

– 20 –

Adjustment Location:

[BD BOARD] – Side B –

(XPCK)

IC101

(FE)

TP (RFO)

TP (TE)

(VC)

(FE1)

(FE2)

IC103

[MAIN BOARD] – Component Side –

CN501 CN506

RV501

IC502

(AFADJ)

(ADJ)

IC501

CN509

CN508

– 21 –

SECTION 7

DIAGRAMS

• Circuit Boards Location

ILLUMINATION board

D. SENS (RAY CATCHER) board

MAIN board

D. SENS (LUMINOUS) board

DISP board

JACK board

T. SENS board

T. MOTOR board

DOOR SN board

JOG board

DOOR MOTOR board

BD board

L. SW board

L. MOTOR board

– 22 –

7-1. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.

(In addition to this, the necessary note is printed in each block.)

Note on Schematic Diagram:

• All capacitors are in µF unless otherwise noted. pF: µµF

50 WV or less are not indicated except for electrolytics

Note on Printed Wiring Boards:

• X : parts extracted from the component side.

• Y : parts extracted from the conductor side.

and tantalums.

• All resistors are in Ω and / W or less unless otherwise

specified.

•

: internal component.

• b : Pattern from the side which enables seeing.

: Solder bridge.

•

: internal component.

• Indication of transistor.

• C : panel designation.

Note:

These are omitted.

Les composants identifiés par

une marque ! sont critiques

pour la sécurité.

Ne les remplacer que par une

piéce portant le numéro

spécifié.

The components identi-

fied by mark ! or dotted

line with mark !are criti-

cal for safety.

Replace only with part

number specified.

B E

•

U : B+ Line.

V : B– Line.

These are omitted.

• H : adjustment for repair.

• Voltages and waveforms are dc with respect to ground

under no-signal conditions.

no mark: PLAY

• Voltages are taken with aVOM (Input impedance 10 MΩ).

Voltage variations may be noted due to normal produc-

tion tolerances.

• Waveforms are taken with a oscilloscope.

Voltage variations may be noted due to normal produc-

tion tolerances.

• Circled numbers refer to waveforms.

• Signal path.

: CD

: digital out

• Abbreviation

AED : North European

AUS : Australian model.

CND : Canadian model.

: 120 V AC Area in E model.

: 240 V AC Area in E model.

: Singapore model.

– 23 –

• Waveforms

– BD Section –

1 IC101 ^§ (XTAI)

– PANEL Section –

1 IC701 %• (OSC0)

3.6 Vp-p

2.5 Vp-p

16.9344 MHz

480 ns

2 IC101 %¡ (RFAC)

500 mV/DIV, 1 µs/DIV

+0.25

–0.20

1.2

Vp-p

3 IC101 $¡ (TE)

200 mV/DIV, 1 µs/DIV

Approx.

500 mVp-p

4 IC101 #ª (FE)

200 mV/DIV, 10 µs/DIV

Approx.

600 mVp-p

– MAIN Section –

1 IC501 #¡ (EXTAL)

3.6 Vp-p

10 MHz

– 24 –

7-2. PRINTED WIRING BOARD – BD Section –

• See page 22 for Circuit Boards Location.

– 25 –

(Page 30)

– 26 –

CDP-CX220

7-3. SCHEMATIC DIAGRAM – BD Section –

• See page 24 for Waveforms. • See page 44 for IC Block Diagrams.

(Page 32)

• no mark: PLAY

• Signal path.

Note:

Les composants identifiés par

une marque ! sont critiques

pour la sécurité.

Ne les remplacer que par une

piéce portant le numéro

spécifié.

The components identi-

fied by mark ! or dotted

line with mark ! are criti-

cal for safety.

Replace only with part

number specified.

: CD

: digital out

– 27 –

– 28 –

CDP-CX220

7-4. PRINTED WIRING BOARD – MAIN Section –

• See page 22 for Circuit Boards Location.

(Page 41)

(Page 37)

(Page 42)

• Semiconductor

Location

Ref. No. Location

D327

D501

D502

D503

D504

D505

D506

D507

D508

D509

D521

E-5

E-4

E-3

E-1

E-5

B-3

(Page 41)

(Page 26)

IC401

IC501

IC502

IC503

IC504

IC505

IC506

C-8

C-3

B-4

C-1

D-5

D-3

C-5

(Page 41)

Q322

Q323

Q325

Q327

Q422

Q423

Q425

Q501

Q503

Q521

E-7

E-6

E-5

E-8

E-6

E-2

C-5

A-3

(Page 41)

(Page 34)

(Page 33)

– 30 –

– 29 –

CDP-CX220

7-5. SCHEMATIC DIAGRAM – MAIN Section –

• See page 24 for Waveforms. • See page 45 for IC Block Diagrams.

(Page 27)

(Page 43)

(Page 36)

(Page 43)

(Page 40)

(Page 35)

• no mark: PLAY

• Signal path.

: CD

: digital out

– 31 –

– 32 –

CDP-CX220

7-6. PRINTED WIRING BOARDS – JACK Section –

• See page 22 for Circuit Boards Location.

(Page 29)

(Page 30)

– 33 –

– 34 –

CDP-CX220

7-7. SCHEMATIC DIAGRAM – JACK Section –

(Page 32)

• no mark: PLAY

• Signal path.

Note:

Les composants identifiés par

une marque ! sont critiques

pour la sécurité.

Ne les remplacer que par une

piéce portant le numéro

spécifié.

The components identi-

fied by mark ! or dotted

line with mark ! are criti-

cal for safety.

Replace only with part

number specified.

: CD

: digital out

– 35 –

– 36 –

7-8. PRINTED WIRING BOARDS – PANEL Section –

• See page 22 for Circuit Boards Location.

(Page 38)

(Page 29)

– 37 –

(Page 37)

• Semiconductor

Location

(DISP Board)

Ref. No. Location

D701

D702

D703

D704

D705

D706

D707

D708

D709

F-4

F-3

F-2

F-4

F-3

F-2

A-5

IC601

IC701

IC702

B-2

C-2

D-1

Q701

D-3

– 38 –

CDP-CX220

7-9. SCHEMATIC DIAGRAM – PANEL Section –

• See page 24 for Waveforms. • See page 46 for IC Block Diagrams.

(Page 31)

– 39 –

– 40 –

7-10. PRINTED WIRING BOARDS – SENSOR/MOTOR Section –

• See page 22 for Circuit Boards Location.

(Page 30)

(Page 29)

– 41 –

(Page 29)

– 42 –

CDP-CX220

7-11. SCHEMATIC DIAGRAM – SENSOR/MOTOR Section –

(Page 31)

– 43 –

• IC Block Diagrams

– BD Board –

IC101 CXD2587Q

ERROR

CORRECTOR

DIGITAL

OUT

ASYMMETRY

CORRECTION

DIGITAL

PLL

16K

RAM

OPERATIONAL

AMPLIFIER

ANALOG SWITCH

LRCK 61

D/A

INTERFACE

EFM

DEMODULATOR

PCMD 62

A/D

CONVERTER

BCK

EMPH 64

XVDD 65

XTAI 66

XTAO 67

TIMING

LOGIC

CLOCK

GENERATOR

XTSL

TES1

TEST

XVSS

AVDD1

AOUT1

AIN1

SERVO DSP

PWM GENERATOR

VSS

33 FRDR

32 FFDR

FOCUS

SERVO

FOCUS PWM

GENERATOR

TRDR

30 TFDR

SRDR

TRACKING

PWM GENERATOR

TRACKING

SERVO

LOUT1 72

AVSS1

SUBCODE

PROCESSOR

PWM

SLED

SLED PWM

SERVO

GENERATOR

28 SFDR

AVSS2 74

SSTP

LOUT2

3rd ORDER

NOISE SHAPER

SERVO

INTERFACE

MDP

DIGITAL

CLV

25 LOCK

OVER SAMPLING

DIGITAL FILTER

AIN2 76

AOUT2 77

AVDD2 78

24 FOK

SERVO AUTO

SEQUENCER

MIRR, DFCT,

FOK

DETECTOR

23 DFCT

22 MIRR

RMUT

SERIAL IN

INTERFACE

LMUT 80

CPU

INTERFACE

COUT

10 11 12 13 14 15 16 17

– 44 –

IC103 CXA2568M-T6

VCC

HOLD

VCC

24 VCC

APC PD AMP

LC/PD

–

APC LD AMP

22 LD ON

VEE

–

21 HOLD SW

AGC CONT

AGC VTH

50µA

–

VCC

19 RF BOT

–

VEE

18 RFTC

RF I

RF SUMMING AMP

RF EQ AMP

16 RF O

–

RFE

FOCUS ERROR AMP

VEE

–

TRACKING

ERROR AMP

E 11

VC BUFFER

VEE

VCC

–

VC 12

– MAIN Board –

IC503 CXA1291P

AMP1

AMP2

THERMAL SHUT

DOWN AND

CURRENT LIMITER

AMP3

– 45 –

IC506 LA5616

VIN1

ON/OFF

CURRENT

LIMITER

OVERHEAT

PROTECT

ON/OFF

VREF

VO1

RESET

GENERATOR

EN1

GND

RES

ERROR

AMP

ERROR

AMP

EN2

VO2

VIN2

– DISP Board –

IC702 M66310FP

– 46 –

7-12. IC PIN FUNCTION DESCRIPTION

• MAINN BOARD IC501 CXP84340-075Q (SYSTEM CONTROLLER)

Pin No.

1 to 5

Pin Name

A3 to A7

A12

I/O

Function

A14

Address signal output to the static RAM (IC502)

8 to 11

A11 to A8

A13

Data write enable signal output to the static RAM (IC502) “L” active

Chip enable signal output to the static RAM (IC502) “H” active

KBCOUT

KBDOUT

KBDIN

FLDATA

FLCLK

LEDLT

TBLL

Serial data transfer clock signal output terminal Not used (open)

Serial data output terminal Not used (open)

Serial data input terminal Not used (open)

Serial data output to the FL driver (IC701) and LED driver (IC702)

Serial data transfer clock signal output to the FL driver (IC701) and LED driver (IC702)

Serial data latch pulse output to the LED driver (IC702) “L” active

Table motor drive signal (counterclockwise) output to the CXA1291P (IC503) “H” active

Table motor drive signal (clockwise) output to the CXA1291P (IC503) “H” active

Door motor drive signal (door close) output to the CXA1291P (IC503) “H” active

Door motor drive signal (door open) output to the CXA1291P (IC503) “H” active

Setting terminal for the test mode “L”: ADJ mode, Normally: fixed at “H”

Loading motor drive signal (load-in direction) output to the CXA1291P (IC503) “H” active

Loading motor drive signal (load-out direction) output to the CXA1291P (IC503) “H” active

Sircs remote control signal output for the S-LINK CONTROL A1 “H” active

Muting on/off control signal output terminal “H” active Not used (pull up)

TBLR

DRIN

DROUT

ADJ

LDIN

LDOUT

BUSOUT

SMUTE

System reset signal input from the reset signal generator (IC505) “L”: reset

For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”

RESET

EXTAL

XTAL

VSS

—

Main system clock input terminal (10 MHz)

Main system clock output terminal (10 MHz)

Ground terminal

Sub system clock output terminal Not used (open)

Sub system clock input terminal Not used (fixed at “L”)

Ground terminal (for A/D converter)

TEX

AVSS

AVREF

D.SENS

DOORSW

—

Reference voltage (+5V) input terminal (for A/D converter)

Inputs the disc sensor (Q801) detection signal (A/D input)

Door open/close detect switch (S810) input (A/D input) “L”: open

COMMAND MODE switch (S901) input terminal (A/D input)

“L”: CD1, “H”: CD3 (CD2: center voltage input)

CD1/2/3

Destination setting terminal (A/D input) Fixed at “L” in this set

Key input terminal (A/D input) p, P, ·, CLEAR, CHECK, ± AMS, ≠ AMS, PUSH

ENTER keys input and rotary encoder jog dial pulse input (S611 to 617 and RE601)

KEY3

Key input terminal (A/D input) § OPEN/CLOSE, INPUT, MEMO SEARCH keys input and

rotary encoder jog dial pulse input (S621 to 623 and RE601)

KEY2

KEY1

KEY0

Key input terminal (A/D input)

I/u, TIME/TEXT, GROUP FILE, GROUP 8/7/6/5 keys input (S731 to 737)

Key input terminal (A/D input)

REPEAT, PROGRAM, SHUFFLE, CONTINUE, GROUP 4/3/2/1 keys input (S721 to 728)

BUSIN

Sircs remote control signal input for the S-LINK CONTROL A1 “L” active

Muting on/off control signal output to the CXD2587Q (IC101) “H”: muting on

AMUTE

– 47 –

Pin No.

Pin Name

CLK

I/O

Function

Command serial data transfer clock signal output to the CXD2587Q (IC101)

Command latch pulse output to the CXD2587Q (IC101) “L” active

Command serial data output to the CXD2587Q (IC101)

XLT

DATA

SENS serial data reading clock and subcode Q data reading clock signal output to the CXD2587Q

(IC101)

SQCLK

SUBQ

Subcode Q data input from the CXD2587Q (IC101)

Not used (open)

SENS

Internal status monitor input from the CXD2587Q (IC101) “H” active

Inputs the loading in/out detect switch (S801) detection signal “L” active

Remote control signal input from the remote control receiver (IC601) “L” active

Setting terminal for the test mode “L”: AFADJ mode, Normally: fixed at “H”

Serial data latch pulse output to the FL driver (IC701) “L” active

Not used (open)

OUTSW

RMIN

AFADJ

FLLT

KBCIN

SCOR

Serial data transfer clock signal output terminal Not used (open)

Subcode sync (S0+S1) detection signal input from the CXD2587Q (IC101) “H” active

Disc table flag detect sensor (IC802) input terminal

T.SENS1

T.SENS2

T.SENS3

ICSW

Disc table flag detect sensor (IC803) input terminal

Disc table home position detect sensor (IC801) input terminal

Enable signal output to the LA5616 (IC506) Used for the BD section reset “H” active

RF AGC hold control signal output to the CXA2568M (IC103) “H” active

Inputs the loading in/out detect switch (S801) detection signal “L” active

Two-way data bus with the static RAM (IC502)

RFSW

INSW

68 to 71

D3 to D6

VDD

I/O

—

I/O

Power supply terminal (+5V)

NC (VDD)

Not used (connected to power supply (+5V) line)

Two-way data bus with the static RAM (IC502)

75 to 77

78 to 80

D2 to D0

A0 to A2

Two-way data bus with the static RAM (IC502)

Address signal output to the static RAM (IC502)

– 48 –

SECTION 8

EXPLODED VIEWS

NOTE:

•

-XX and -X mean standardized parts, so they

may have some difference from the original

one.

Color Indication of Appearance Parts

Example:

KNOB, BALANCE (WHITE) . . . (RED)

• The mechanical parts with no reference num-

ber in the exploded views are not supplied.

• Hardware (# mark) list and accessories and

packing materials are given in the last of the

electrical parts list.

• Abbreviation

AED : North European

AUS : Australian

CND : Canadian

The components identified by

mark ! or dotted line with mark

! are critical for safety.

Replace only with part number

specified.

•

Les composants identifiés par une

marque ! sont critiquens pour la

sécurité.

Ne les remplacer que par une pièce

portant le numéro spécifié.

↑

Parts Color Cabinet's Color

Items marked “*” are not stocked since they

are seldom required for routine service. Some

delay should be anticipated when ordering

these items.

•

SP : Singapore

(1) CASE, FRONT PANEL SECTION

not supplied

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

X-4949-616-1 DOOR (CD) ASSY

4-998-523-01 KNOB (JOG)

X-4949-618-1 PANEL ASSY, FRONT (US, CND)

X-4949-619-1 PANEL ASSY, FRONT (EXCEPT US, CND)

4-996-698-01 EMBLEM, SONY

* 7

* 9

A-4724-027-A DISP BOARD, COMPLETE (US, CND)

A-4724-033-A DISP BOARD, COMPLETE (EXCEPT US, CND)

1-783-364-11 WIRE (FLAT TYPE) (15 CORE)

1-669-161-11 JOG BOARD

3-363-099-01 SCREW (CASE 3 TP2)

4-951-620-01 SCREW (2.6X8), +BVTP

4-985-553-21 CUSHION

* 11

4-982-946-11 CASE

4-977-358-11 CUSHION (FOOT)

– 49 –

(2) GUIDE ASSY, REAR PANEL SECTION

not supplied

AUS

AEP, UK, AED,

not

supplied

US, CND

not

supplied

not

supplied

T901

not

supplied

The components identified by Les composants identifiés par une

mark ! or dotted line with marque ! sont critiques pour la

mark ! are critical for safety. sécurité.

Replace only with part num- Ne les remplacer que par une pièce

ber specified.

portant le numéro spécifié.

Ref. No.

Part No.

Description

Remark

Ref. No.

* 65

Part No.

Description

Remark

* 51

* 52

* 55

4-982-802-01 RING (A)

4-982-803-01 RING (B)

4-998-506-01 GUIDE (DOOR. T)

4-999-182-01 ILLUMINATOR

4-998-525-01 PANEL, BACK (US)

4-998-525-11 PANEL, BACK (CND)

4-998-525-21 PANEL, BACK (AEP, UK, AED)

4-998-525-41 PANEL, BACK (SP)

4-998-525-51 PANEL, BACK (E)

1-669-166-11 ILLUMINATION BOARD

* 60

4-982-870-01 SHAFT (GUIDE FULCRUM)

3-356-601-11 SCREW, STEP

4-982-862-01 GUIDE (DISC T)

4-985-553-11 CUSHION

* 65

* 66

4-998-525-61 PANEL, BACK (AUS)

A-4724-022-A MAIN BOARD, COMPLETE (US, CND)

A-4724-031-A MAIN BOARD, COMPLETE (EXCEPT US, CND)

4-886-821-11 SCREW, S TIGHT, +PTTWH 3X6

4-053-543-01 RIVET, NYLON

3-378-434-01 CUSHION, SARANET

* 61

!62

4-982-807-01 COVER (FFC)

1-575-042-21 CORD, POWER (US, CND)

1-575-651-21 CORD, POWER (AEP, UK, AED, SP)

1-696-027-11 CORD, POWER (E)

1-696-845-11 CORD, POWER (AUS)

* 69

!T901

1-669-164-11 JACK BOARD

1-773-183-11 WIRE (FLAT TYPE) (23 CORE)

4-956-370-12 BAND, PLUG FIXED (AUS)

1-431-759-11 TRANSFORMER, POWER (US, CND)

1-431-760-11 TRANSFORMER, POWER

(AEP, UK, AED, SP, AUS)

!63

* 64

1-569-007-11 ADAPTOR, CONVERSION 2P (E)

3-703-244-00 BUSHING (2104), CORD (EXCEPT E)

3-703-571-11 BUSHING (S) (4516), CORD (E)

!T901

1-431-761-11 TRANSFORMER, POWER (E)

– 50 –

(3) CHASSIS SECTION

#10

118

108

109

110

CDM-40B

119

111

106

121

117

112

120

107

106

104

122

112

113

116

103

124

not

supplied

105

123

M801

114

125

127

115

128

102

126

M810

101

not

supplied

not

supplied

129

130

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

* 101

* 102

103

104

105

1-669-167-11 DOOR MOTOR BOARD

X-4949-615-1 BRACKET (GEAR) ASSY

4-998-510-01 GEAR (PULLEY)

4-998-509-01 GEAR (CENTER)

4-998-508-01 GEAR (DOOR)

* 117

118

119

120

121

1-661-469-11 D. SENS (RAY CATCHER) BOARD

4-976-471-01 BEARING (TABLE)

X-4947-231-1 TABLE (200) ASSY

4-982-892-01 SHAFT (CENTER)

4-982-891-01 GEAR (TABLE)

106

107

108

* 109

* 110

3-325-697-21 WASHER

122

123

124

* 125

126

4-962-822-01 BELT (TIMING)

4-998-507-01 GUIDE (DOOR.B)

4-951-620-01 SCREW (2.6X8), +BVTP

1-669-168-11 DOOR SW BOARD

1-661-470-11 T. SENS BOARD

4-982-893-01 GEAR (CENTER 2)

X-4947-607-1 GEAR (PULLEY) ASSY

1-661-466-11 T. MOTOR BOARD

3-703-397-01 STOPPER, WIRING

* 111

112

113

114

115

1-661-468-11 D. SENS (LUMINOUS) BOARD

3-356-601-11 SCREW, STEP

4-210-030-01 BELT (42X1)

X-4947-230-2 BRACKET (TABLE) ASSY

X-4947-606-1 HOLDER (ROLLER 2) ASSY

127

128

129

130

M801

4-985-574-01 SPACER (ROLLER)

X-4947-229-1 HOLDER (ROLLER) ASSY

4-983-279-01 CUSHION (RF)

4-931-169-01 FOOT

A-4604-847-A MOTOR ASSY (TABLE)

116

3-701-446-21 WASHER, 8

M810

X-4950-062-1 DOOR MOTOR ASSY

– 51 –

(4) MECHANISM DECK SECTION-1

(CDM-40B)

not supplied

174

#11

169

161

171

168

173

167

170

162

not supplied

172

160

154

153

not supplied

#13

151

159

152

155

not supplied

158

#12

166

165

156

157

164

163

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

151

152

153

154

155

X-4947-241-1 LEVER (C) ASSY

163

164

165

166

167

A-4672-092-A MAGNET ASSY

4-982-882-01 SPRING (LIMITTER), TORSION

4-982-881-01 SPRING (HOLDER), TORSION

X-4947-239-1 LIMITTER (A) ASSY

4-982-853-01 LEVER (B)

3-366-559-02 MAGNET (CHUCK)

4-960-633-01 YOKE (MAGNET)

4-960-632-11 PULLEY (B)

4-983-319-01 SPRING (THRUST), COMPRESSION

156

157

158

159

160

X-4947-240-1 LEVER (A) ASSY

4-988-143-01 HOLDER (DISC A2)

4-982-855-01 HOLDER (DISC B)

4-982-856-01 PAD

* 168

169

170

171

172

4-976-456-01 WASHER (STOPPER)

3-938-588-01 SPRING, COMPRESSION

X-4947-242-1 SLIDER (C) ASSY

X-4947-238-1 SLIDER (B) ASSY

X-4947-237-1 SLIDER (A) ASSY

4-976-458-01 HOLDER (MAGNET)

161

162

X-4946-326-1 HOLDER (CLAMP) ASSY

4-983-777-01 SPRING (MG), TENSION

173

* 174

4-982-880-01 SPRING (SLIDER A), TENSION

4-982-863-01 GUIDE (DISC P)

– 52 –

(5) MECHANISM DECK SECTION-2

(CDM-40B)

212

206

210

213

206

205

201

214

206

216

not supplied

206

202

203

215

204

not supplied

#10

211

209

not supplied

#14

208

M802

207

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

201

202

203

204

205

4-976-465-01 GEAR (LOADING 1)

4-976-466-01 GEAR (LOADING 2)

4-982-893-01 GEAR (CENTER 2)

X-4947-607-1 GEAR (PULLEY) ASSY

4-982-867-01 BELT (TIMING)

210

211

212

213

214

X-4947-227-1 LEVER (STOPPER) ASSY

4-951-291-01 SCREW

X-4947-234-1 SLIDER (LOCK) ASSY

4-982-857-01 BEARING (CAM)

4-982-860-01 CAM (A)

206

* 207

* 208

209

3-325-697-21 WASHER

215

216

M802

4-982-861-01 CAM (B)

3-356-601-11 SCREW, STEP

A-4604-847-A MOTOR ASSY (LOADING)

1-661-465-11 L. MOTOR BOARD

1-661-467-11 L. SW BOARD

3-489-073-00 SCREW, THRUST

– 53 –

(6) MECHANISM DECK SECTION-3

(CDM-40B)

#15

259

KSM-213BKN/M-N

#15

255

258

#15

259

255

258

#15

259

255

257

258

255

256

255

254

255

254

253

251

252

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

251

252

253

254

255

3-356-601-11 SCREW, STEP

X-4947-244-1 SLIDER (BU ADJUSTMENT) ASSY

X-4947-243-1 HOLDER (BU) ASSY

4-982-859-01 HOLDER (DAMPER)

4-982-878-01 SPRING (F), COMPRESSION

256

257

258

259

4-982-872-01 SPRING (F-2), TENSION

4-982-871-01 SPRING (F-1), TENSION

4-982-858-01 DAMPER

4-960-617-01 CAP (F)

– 54 –

(7) OPTICAL PICK-UP SECTION

(KSM-213BKN/M-N)

not supplied

305

306

303

#16

302

M101

304

M102

301

#15

The components identified by Les composants identifiés par une

mark ! or dotted line with marque ! sont critiques pour la

mark ! are critical for safety. sécurité.

Replace only with part num- Ne les remplacer que par une pièce

ber specified.

portant le numéro spécifié.

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

* 301

302

A-4724-029-A BD BOARD, COMPLETE

2-626-907-01 GEAR (A)

305

!306

2-626-908-01 SHAFT, SLED

8-848-379-31 OPTICAL PICK-UP KSM-213BKN/M-N

303

304

2-627-003-02 GEAR (B) (RP)

1-769-069-11 WIRE (FLAT TYPE) (16 CORE)

M101

M102

X-2626-234-1 T. T CHASSIS ASSY (MG) (K) (SPINDLE)

X-2625-769-1 MOTOR GEAR ASSY (MB) (PP) (SLED)

– 55 –

SECTION 9

ELECTRICAL PARTS LIST

NOTE:

• Due to standardization, replacements in the

parts list may be different from the parts speci-

fied in the diagrams or the components used

on the set.

• -XX and -X mean standardized parts, so they

may have some difference from the original

one.

•

SEMICONDUCTORS

In each case, u: µ, for example:

The components identified by

mark ! or dotted line with mark

! are critical for safety.

uA. . : µA. .

uPB. . : µPB. .

uPD. . : µPD. .

CAPACITORS

uF: µF

uPA. . : µPA. .

uPC. . : µPC. .

Replace only with part number

specified.

Les composants identifiés par une

marque ! sont critiquens pour la

sécurité.

Ne les remplacer que par une pièce

portant le numéro spécifié.

•

• RESISTORS

All resistors are in ohms.

COILS

uH: µH

Abbreviation

AED : North European

AUS : Australian

CND : Canadian

METAL: Metal-film resistor.

METAL OXIDE: Metal oxide-film resistor.

F: nonflammable

• Items marked “*” are not stocked since they

are seldom required for routine service.

Some delay should be anticipated when order-

ing these items.

When indicating parts by reference

number, please include the board.

SP : Singapore

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

A-4724-029-A BD BOARD, COMPLETE

C163

C164

1-126-205-11 ELECT CHIP

1-163-038-00 CERAMIC CHIP 0.1uF

47uF

20%

6.3V

25V

******************

< CAPACITOR >

C165

C166

C167

C168

C171

1-163-038-00 CERAMIC CHIP 0.1uF

1-163-235-11 CERAMIC CHIP 22PF

1-163-237-11 CERAMIC CHIP 27PF

1-163-137-00 CERAMIC CHIP 680PF

25V

50V

C101

C102

C103

C104

C106

1-163-005-11 CERAMIC CHIP 470PF

1-163-038-00 CERAMIC CHIP 0.1uF

1-163-005-11 CERAMIC CHIP 470PF

1-164-232-11 CERAMIC CHIP 0.01uF

1-164-346-11 CERAMIC CHIP 1uF

10%

50V

25V

50V

16V

C172

C181

C182

1-163-251-11 CERAMIC CHIP 100PF

1-163-137-00 CERAMIC CHIP 680PF

1-163-251-11 CERAMIC CHIP 100PF

50V

C107

C108

C109

C110

C111

1-164-346-11 CERAMIC CHIP 1uF

1-163-035-00 CERAMIC CHIP 0.047uF

1-163-145-00 CERAMIC CHIP 0.0015uF 5%

1-163-017-00 CERAMIC CHIP 0.0047uF 5%

1-163-251-11 CERAMIC CHIP 100PF

16V

50V

< CONNECTOR >

CN101 1-770-072-11 CONNECTOR, (LIF (NON-ZIF)) FFC23P

CN102 1-777-937-11 CONNECTOR, FFC/FPC 16P

C112

C113

C114

C115

C116

1-163-038-00 CERAMIC CHIP 0.1uF

25V

< IC >

1-126-607-11 ELECT CHIP

47uF

20%

IC101 8-752-386-85 IC CXD2587Q

IC102 8-759-455-91 IC BA6392FP-E2

IC103 8-752-085-51 IC CXA2568M-T6

C117

C118

C119

C120

C121

1-126-209-11 ELECT CHIP

1-163-275-11 CERAMIC CHIP 0.001uF 5%

1-163-231-11 CERAMIC CHIP 15PF

1-163-038-00 CERAMIC CHIP 0.1uF

100uF

20%

50V

25V

< COIL >

L101

L102

1-414-234-11 INDUCTOR CHIP 0uH

C122

C123

C124

C125

C126

1-135-155-21 TANTALUM CHIP 4.7uF

1-164-232-11 CERAMIC CHIP 0.01uF

1-164-005-11 CERAMIC CHIP 0.47uF

1-163-038-00 CERAMIC CHIP 0.1uF

10%

16V

50V

25V

< TRANSISTOR >

8-729-010-08 TRANSISTOR MSB710-R

< RESISTOR >

Q101

C127

C130

C131

C140

C141

1-109-982-11 CERAMIC CHIP 1uF

1-164-004-11 CERAMIC CHIP 0.1uF

1-135-216-11 TANTALUM CHIP 10uF

1-163-038-00 CERAMIC CHIP 0.1uF

10%

20%

10V

25V

10V

25V

R101

R102

R103

R104

R105

1-216-077-00 METAL CHIP

1-216-097-00 RES, CHIP

1-216-077-00 METAL CHIP

1-216-085-00 METAL CHIP

1-216-097-00 RES, CHIP

15K

100K

15K

33K

100K

1/10W

C151

C153

C154

C156

C157

1-163-237-11 CERAMIC CHIP 27PF

1-163-038-00 CERAMIC CHIP 0.1uF

1-164-336-11 CERAMIC CHIP 0.33uF

1-163-237-11 CERAMIC CHIP 27PF

50V

25V

50V

R106

R107

R108

R109

R110

1-216-061-00 METAL CHIP

1-216-073-00 METAL CHIP

1-216-121-00 RES, CHIP

1-216-025-00 RES, CHIP

3.3K

10K

1/10W

1-163-145-00 CERAMIC CHIP 0.0015uF 5%

100

C159

C161

C162

1-163-019-00 CERAMIC CHIP 0.0068uF 10%

50V

6.3V

R111

R113

R116

1-216-121-00 RES, CHIP

1-216-025-00 RES, CHIP

100

1/10W

1-126-205-11 ELECT CHIP

47uF

20%

– 56 –

BD D. SENS (LUMINOUS) D. SENS (RAY CATCHER) DISP

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

R117

R119

1-216-049-11 RES, CHIP

1-216-043-00 RES, CHIP

560

1/10W

C703

C704

C705

1-162-306-11 CERAMIC

1-164-159-11 CERAMIC

1-124-584-00 ELECT

0.01uF

0.1uF

100uF

20%

16V

50V

10V

R123

R124

R131

R135

R136

1-216-073-00 METAL CHIP

1-216-097-00 RES, CHIP

1-216-037-00 METAL CHIP

1-216-295-00 SHORT

10K

100K

330

1/10W

C706

C707

C708

C709

C710

1-162-282-31 CERAMIC

1-162-288-31 CERAMIC

1-124-584-00 ELECT

100PF

330PF

100uF

10%

20%

50V

10V

1-216-295-00 SHORT

R137

R138

R143

R144

R147

1-216-295-00 SHORT

1-216-103-00 METAL CHIP

1-216-081-00 METAL CHIP

180K

22K

C711

C712

1-164-159-11 CERAMIC

0.1uF

50V

1/10W

< LEAD PIN >

R148

R149

R158

R159

R161

1-216-001-00 METAL CHIP

1-216-003-11 RES, CHIP

1-216-111-00 METAL CHIP

1-216-101-00 METAL CHIP

1-216-308-00 METAL CHIP

390K

150K

4.7

1/10W

* CLP701 1-690-880-31 LEAD (WITH CONNECTOR)

< LED >

D701

D702

D703

D704

D705

8-719-046-39 LED SEL5821A-TH15 (GROUP 1)

8-719-046-39 LED SEL5821A-TH15 (GROUP 2)

8-719-046-39 LED SEL5821A-TH15 (GROUP 3)

8-719-046-39 LED SEL5821A-TH15 (GROUP 4)

8-719-046-39 LED SEL5821A-TH15 (GROUP 5)

R162

R171

R172

R173

R181

1-216-101-00 METAL CHIP

1-216-077-00 METAL CHIP

150K

15K

1/10W

D706

D707

D708

D709

8-719-046-39 LED SEL5821A-TH15 (GROUP 6)

8-719-046-39 LED SEL5821A-TH15 (GROUP 7)

8-719-046-39 LED SEL5821A-TH15 (GROUP 8)

8-719-046-44 LED SEL5221S (STANDBY)

R182

R183

1-216-077-00 METAL CHIP

15K

1/10W

< SWITCH >

< FLUORESCENT INDICATOR TUBE >

S101

X101

1-572-085-11 SWITCH, LEAF (LIMIT)

< VIBRATOR >

FL701 1-517-756-11 INDICATOR TUBE, FLUORESCENT

< IC >

1-767-408-41 VIBRATOR, CRYSTAL (16.9344MHz)

IC601 8-749-014-66 IC NJL56H400

IC701 8-759-498-92 IC MSM9202-03GS-K

IC702 8-759-183-47 IC M66310FP

************************************************************

1-661-468-11 D.SENS (LUMINOUS) BOARD

***********************

< TRANSISTOR >

4-976-473-01 HOLDER (LED-S)

< DIODE >

Q701

8-729-900-80 TRANSISTOR DTC114ES

< RESISTOR >

D801

8-719-055-84 DIODE GL-528VS1

R701

R702

R703

R704

R705

1-249-441-11 CARBON

1-247-807-31 CARBON

100K

100

1/4W

************************************************************

1-661-469-11 D.SENS (RAY CATCHER) BOARD

**************************

4-985-300-01 HOLDER (P-T)

< PHOTO TRANSISTOR >

R706

R707

R708

R709

R711

1-247-843-11 CARBON

1-247-807-31 CARBON

1-249-411-11 CARBON

3.3K

100

330

1/4W

Q801

8-729-926-31 PHOTO TRANSISTOR PT483F1S

************************************************************

R712

R713

R722

R723

R724

1-249-411-11 CARBON

1-249-413-11 CARBON

1-249-415-11 CARBON

1-249-417-11 CARBON

1-249-419-11 CARBON

330

470

680

1/4W

A-4724-027-A DISP BOARD, COMPLETE (US, CND)

A-4724-033-A DISP BOARD, COMPLETE (EXCEPT US, CND)

********************

1.5K

4-982-811-01 HOLDER (FL)

< CAPACITOR >

R725

R726

R727

R728

R732

1-249-421-11 CARBON

1-247-843-11 CARBON

1-249-427-11 CARBON

1-249-431-11 CARBON

1-249-415-11 CARBON

2.2K

3.3K

6.8K

15K

680

1/4W

C701

C702

1-162-294-31 CERAMIC

1-162-215-31 CERAMIC

0.001uF 10%

47PF 5%

50V

– 57 –

DISP DOOR MOTOR DOOR SW ILLUMINATION JACK

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

1-669-164-11 JACK BOARD

R733

R734

R735

R736

R737

1-249-417-11 CARBON

1-249-419-11 CARBON

1-249-421-11 CARBON

1-247-843-11 CARBON

1-249-427-11 CARBON

1/4W

**********

1.5K

2.2K

3.3K

6.8K

4-962-200-11 PLATE (TR), GROUND

< CAPACITOR >

R751

1-249-429-11 CARBON

10K

1/4W

C351

C451

C901

C904

C907

1-162-290-31 CERAMIC

1-161-494-00 CERAMIC

1-164-159-11 CERAMIC

470PF

10%

50V

25V

50V

470PF

0.022uF

0.1uF

< SWITCH >

S721

S722

S723

S724

S725

1-572-184-11 SWITCH, KEYBOARD (REPEAT)

1-572-184-11 SWITCH, KEYBOARD (PROGRAM)

1-572-184-11 SWITCH, KEYBOARD (SHUFFLE)

1-572-184-11 SWITCH, KEYBOARD (CONTINUE)

1-572-184-11 SWITCH, KEYBOARD (GROUP 4)

0.1uF

C911

C912

1-161-494-00 CERAMIC

1-126-052-11 ELECT

0.022uF

100uF

25V

10V

20%

< CONNECTOR >

S726

S727

S728

S731

S732

1-572-184-11 SWITCH, KEYBOARD (GROUP 3)

1-572-184-11 SWITCH, KEYBOARD (GROUP 2)

1-572-184-11 SWITCH, KEYBOARD (GROUP 1)

1-572-184-11 SWITCH, KEYBOARD (I/u)

CN902 1-569-497-11 SOCKET, CONNECTOR 11P

* CN903 1-569-496-11 SOCKET, CONNECTOR 10P

* CN904 1-568-951-11 PIN, CONNECTOR 2P

1-572-184-11 SWITCH, KEYBOARD (TIME/TEXT)

CN906 1-580-230-11 PIN, CONNECTOR (PC BOARD) 2P

S733

S734

S735

S736

S737

1-572-184-11 SWITCH, KEYBOARD (GROUP FILE)

1-572-184-11 SWITCH, KEYBOARD (GROUP 8)

1-572-184-11 SWITCH, KEYBOARD (GROUP 7)

1-572-184-11 SWITCH, KEYBOARD (GROUP 6)

1-572-184-11 SWITCH, KEYBOARD (GROUP 5)

< DIODE >

D901

8-719-911-19 DIODE 1SS119

< IC >

************************************************************

IC901 8-749-921-12 IC GP1F32T (DIGITAL OUT OPTICAL)

< JACK >

1-669-167-11 DOOR MOTOR BOARD

******************

< CONNECTOR >

* J901

1-764-188-11 JACK (SMALL TYPE) (DIA. 3.5)

(S-LINK CONTROL A1)

1-764-188-11 JACK (SMALL TYPE) (DIA. 3.5)

(S-LINK CONTROL A1)

* CN812 1-568-951-11 PIN, CONNECTOR 2P

************************************************************

* J902

1-669-168-11 DOOR SW BOARD

J904

1-770-719-11 JACK, PIN 2P (LINE OUT)

< LINE FILTER >

**************

< RESISTOR >

1-249-429-11 CARBON

< SWITCH >

!L901

L902

1-421-915-11 FILTER, LINE (EXCEPT E)

< COIL >

R807

S810

10K

1/4W

1-410-503-11 INDUCTOR

3.3uH

1-571-300-21 SWITCH, ROTARY (DOOR SW)

************************************************************

< TRANSISTOR >

1-669-166-11 ILLUMINATION BOARD

Q901

8-729-620-05 TRANSISTOR 2SC2603-EF

< RESISTOR >

******************

< CONNECTOR >

CN813 1-506-481-11 PIN, CONNECTOR 2P

< LED >

R351

R451

R901

R902

R903

1-215-405-00 METAL

1-249-393-11 CARBON

1-249-425-11 CARBON

1-249-429-11 CARBON

220

4.7K

10K

1/4W

D802

D803

D804

8-719-059-65 LED HLMF-KL05 (INSIDE ILLUMINATION)

R921

1-249-429-11 CARBON

10K

1/4W

< SWITCH >

< RESISTOR >

S901

!S902

1-762-910-11 SWITCH, SLIDE (COMMAND MODE)

1-572-675-11 SWITCH, POWER VOLTAGE CHANGE

R805

R806

1-249-407-11 CARBON

1-249-401-11 CARBON

150

1/4W

(VOLTAGE SELECTOR) (E)

************************************************************

The components identified by Les composants identifiés par une

mark ! or dotted line with marque ! sont critiques pour la

mark ! are critical for safety. sécurité.

Replace only with part num- Ne les remplacer que par une pièce

ber specified.

portant le numéro spécifié.

– 58 –

JACK JOG L.MOTOR L.SW MAIN

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

< TRANSFORMER >

1-661-467-11 L.SW BOARD

**********

!T901

1-431-759-11 TRANSFORMER, POWER (US, CND)

1-431-760-11 TRANSFORMER, POWER

< SWITCH >

(AEP, AED, UK, SP, AUS)

1-431-761-11 TRANSFORMER, POWER (E)

!T901

S801

1-571-300-21 SWITCH, ROTARY (LOADING DET)

************************************************************ ************************************************************

1-669-161-11 JOG BOARD

A-4724-022-A MAIN BOARD, COMPLETE (US, CND)

A-4724-031-A MAIN BOARD, COMPLETE (EXCEPT US, CND)

*********************

**********

< CONNECTOR >

7-685-871-01 SCREW +BVTT 3X6 (S)

< CAPACITOR >

* CN601 1-569-306-11 SOCKET, CONNECTOR (L TYRE) 15P

< LED >

C301

C305

C327

C401

C405

1-126-233-11 ELECT

1-126-052-11 ELECT

1-126-163-11 ELECT

1-126-233-11 ELECT

1-126-052-11 ELECT

22uF

20%

50V

10V

50V

10V

D601

D602

8-719-046-40 LED SEL5521C-TH8F (·)

8-719-046-38 LED SEL5821A-TH8F (P)

100uF

4.7uF

22uF

< RESISTOR >

100uF

R601

R602

R612

R613

R614

1-249-407-11 CARBON

1-249-409-11 CARBON

1-249-415-11 CARBON

1-249-417-11 CARBON

1-249-419-11 CARBON

150

220

680

1/4W

C501

C502

1-128-489-11 ELECT

1-124-360-00 ELECT

3300uF 20%

1000uF 20%

16V

(US, CND)

25V

C502

1-126-027-11 ELECT

1000uF 20%

1.5K

(EXCEPT US, CND)

R615

R616

R617

R618

R619

1-249-421-11 CARBON

1-247-843-11 CARBON

1-249-427-11 CARBON

1-249-431-11 CARBON

1-249-437-11 CARBON

2.2K

3.3K

6.8K

15K

47K

1/4W

C503

C504

C505

C506

C507

1-124-122-11 ELECT

1-126-021-11 ELECT

1-126-052-11 ELECT

1-126-101-11 ELECT

1-126-044-11 ELECT

100uF

33uF

100uF

1uF

20%

50V

35V

16V

50V

R622

R623

R624

R651

R652

1-249-415-11 CARBON

1-249-417-11 CARBON

1-249-419-11 CARBON

1-249-429-11 CARBON

680

1.5K

10K

1/4W

C508

C509

C510

C511

C512

1-126-101-11 ELECT

1-124-997-11 ELECT

1-126-163-11 ELECT

1-161-494-00 CERAMIC

100uF

470uF

4.7uF

0.022uF

20%

16V

10V

50V

25V

< ROTARY ENCODER >

C513

C514

C516

C518

1-126-052-11 ELECT

1-126-023-11 ELECT

1-164-159-11 CERAMIC

100uF

0.1uF

20%

16V

25V

50V

RE601 1-475-543-11 ENCODER, ROTARY

(DISC/CHARACTER PUSH ENTER)

< SWITCH >

C519

C521

C522

C531

C532

1-164-159-11 CERAMIC

1-110-489-11 CAPACITOR

1-161-494-00 CERAMIC

1-126-052-11 ELECT

0.1uF

0.022uF

100uF

50V

5.5V

25V

10V

S611

S612

S613

S614

S615

1-572-184-11 SWITCH, KEYBOARD (p)

1-572-184-11 SWITCH, KEYBOARD (P)

1-572-184-11 SWITCH, KEYBOARD (·)

1-572-184-11 SWITCH, KEYBOARD (CLEAR)

1-572-184-11 SWITCH, KEYBOARD (CHECK)

20%

C533

C551

C552

C561

C562

1-161-494-00 CERAMIC

1-136-165-00 FILM

1-164-159-11 CERAMIC

1-136-165-00 FILM

0.022uF

0.1uF

25V

50V

S616

S617

S621

S622

S623

1-572-184-11 SWITCH, KEYBOARD (±, AMS)

1-572-184-11 SWITCH, KEYBOARD (≠, AMS)

1-572-184-11 SWITCH, KEYBOARD (§, OPEN/CLOSE)

1-572-184-11 SWITCH, KEYBOARD (INPUT)

1-164-159-11 CERAMIC

1-572-184-11 SWITCH, KEYBOARD (MEMO SEARCH)

C571

C572

C610

C620

C720

1-136-165-00 FILM

0.1uF

0.022uF

50V

25V

************************************************************

1-164-159-11 CERAMIC

1-161-494-00 CERAMIC

1-661-465-11 L.MOTOR BOARD

**************

************************************************************

C730

1-161-494-00 CERAMIC

0.022uF

25V

< CONNECTOR >

CN501 1-569-321-11 SOCKET, CONNECTOR 15P

CN502 1-568-742-11 SOCKET, CONNECTOR 23P

The components identified by Les composants identifiés par une

mark ! or dotted line with marque ! sont critiques pour la

mark ! are critical for safety. sécurité.

Replace only with part num- Ne les remplacer que par une pièce

ber specified.

portant le numéro spécifié.

– 59 –

MAIN

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

* CN503 1-568-951-11 PIN, CONNECTOR 2P

CN504 1-506-469-11 PIN, CONNECTOR 4P

CN505 1-506-468-11 PIN, CONNECTOR 3P

R323

R325

R327

R401

R402

1-249-421-11 CARBON

1-249-441-11 CARBON

1-215-453-00 METAL

1-215-425-00 METAL

2.2K

100K

22K

1/4W

* CN506 1-568-955-11 PIN, CONNECTOR 6P

* CN507 1-568-951-11 PIN, CONNECTOR 2P

* CN508 1-569-505-11 PIN, CONNECTOR 10P

* CN509 1-569-506-11 PIN, CONNECTOR 11P

1.5K

R403

R404

R405

R413

R414

1-215-425-00 METAL

1-215-445-00 METAL

1-215-443-00 METAL

1-215-469-00 METAL

1-215-405-00 METAL

1.5K

10K

8.2K

100K

220

1/4W

< DIODE >

D327

D501

D502

D503

D504

8-719-911-19 DIODE 1SS119

8-719-024-99 DIODE 11ES2-NTA2B

R415

R416

R422

R423

R425

1-215-405-00 METAL

1-249-393-11 CARBON

1-249-421-11 CARBON

1-249-441-11 CARBON

220

2.2K

100K

1/4W

D505

D506

D507

D508

D509

8-719-024-99 DIODE 11ES2-NTA2B

8-719-110-72 DIODE RD30ESB2

8-719-109-93 DIODE RD6.2ESB2

8-719-109-85 DIODE RD5.1ES-B2

8-719-911-19 DIODE 1SS119

R501

R502

R505

R506

R507

1-249-435-11 CARBON

1-249-425-11 CARBON

1-249-413-11 CARBON

1-249-429-11 CARBON

1-249-425-11 CARBON

33K

4.7K

470

10K

4.7K

1/4W

D521

8-719-911-19 DIODE 1SS119

< IC >

R508

R511

R512

R521

R522

1-249-413-11 CARBON

1-249-425-11 CARBON

1-249-429-11 CARBON

1-249-403-11 CARBON

470

4.7K

10K

1/4W

IC401 8-759-145-58 IC uPC4558C

IC501 8-752-892-41 IC CXP84340-075Q

IC502 8-759-463-99 IC M5M5256DFP-70XL

IC503 8-759-821-32 IC CXA1291P

IC504 8-759-094-53 IC TA7805S

R523

R524

R531

R532

R533

1-249-403-11 CARBON

1-249-429-11 CARBON

1/4W

10K

IC505 8-759-256-72 IC PST994D

IC506 8-759-330-29 IC LA5616

< COIL >

R534

R535

R536

R537

R538

1-249-421-11 CARBON

1-247-843-11 CARBON

1-249-425-11 CARBON

1-249-429-11 CARBON

2.2K

3.3K

4.7K

10K

1/4W

L501

L502

1-412-473-21 INDUCTOR

0uH

< TRANSISTOR >

R539

R540

R541

R542

R543

1-249-429-11 CARBON

10K

1/4W

Q322

Q323

Q325

Q327

Q422

8-729-141-26 TRANSISTOR 2SC3622A-LK

8-729-900-65 TRANSISTOR DTA144ES

8-729-141-26 TRANSISTOR 2SC3622A-LK

R544

R551

R552

R553

R554

1-249-429-11 CARBON

1-247-887-00 CARBON

1-247-860-11 CARBON

1-249-431-11 CARBON

10K

1/4W

Q423

Q425

Q501

Q503

Q521

8-729-141-26 TRANSISTOR 2SC3622A-LK

8-729-900-65 TRANSISTOR DTA144ES

8-729-140-97 TRANSISTOR 2SB734-34

8-729-119-76 TRANSISTOR 2SA1175-HFE

8-729-030-08 TRANSISTOR DTC144VSA-TP

220K

16K

15K

R555

R556

R557

R558

R561

1-249-382-11 CARBON

1-247-883-00 CARBON

1-249-393-11 CARBON

1-249-441-11 CARBON

1.2

150K

100K

1/6W

1/4W

< RESISTOR >

R301

R302

R303

R304

R305

1-215-453-00 METAL

1-215-425-00 METAL

1-215-445-00 METAL

1-215-443-00 METAL

22K

1.5K

10K

8.2K

1/4W

R562

R563

R564

R565

R566

1-249-441-11 CARBON

1-247-860-11 CARBON

1-249-431-11 CARBON

1-249-382-11 CARBON

100K

16K

15K

1.2

1/4W

1/6W

R313

R314

R315

R316

R322

1-215-469-00 METAL

1-215-405-00 METAL

1-249-393-11 CARBON

1-249-421-11 CARBON

100K

220

1/4W

1.2

R567

R568

R571

1-247-883-00 CARBON

1-249-393-11 CARBON

1-247-885-00 CARBON

150K

180K

1/4W

2.2K

– 60 –

MAIN T.MOTOR T.SENS

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

R572

R573

1-247-885-00 CARBON

1-247-860-11 CARBON

180K

16K

1/4W

M810

!T901

X-4950-062-1 DOOR MOTOR ASSY

1-431-759-11 TRANSFORMER, POWER (US, CND)

R574

R575

R576

R577

R578

1-249-431-11 CARBON

1-249-382-11 CARBON

1-247-883-00 CARBON

1-249-393-11 CARBON

15K

1.2

150K

1/4W

1/6W

1/4W

!T901

1-431-760-11 TRANSFORMER, POWER

(AEP, UK, AED, SP, AUS)

1-431-761-11 TRANSFORMER, POWER (E)

!T901

************************************************************

**************

HARDWARE LIST

**************

R581

R610

R620

R720

R730

1-249-429-11 CARBON

1-249-427-11 CARBON

10K

1/4W

6.8K

7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S

7-685-871-01 SCREW +BVTT 3X6 (S)

7-685-134-19 SCREW +PTPWH 2.6X8 (TYPE2)

7-624-106-04 STOP RING 3.0, TYPE -E

7-682-947-01 SCREW +PSW 3X6

< VARIABLE RESISTOR >

RV501 1-241-787-11 RES, ADJ, CARBON 47K

< VIBRATOR >

#10

7-682-547-04 SCREW +BV 3X6, S TIGHT

7-685-872-09 SCREW +BVTT 3X8 (S)

7-621-775-00 SCREW +B 2.6X3

7-685-647-79 SCREW +BVTP 3X10 TYPE2 N-S

7-624-111-04 STOP RING 7.0, TYPE -E

X501

1-579-175-11 VIBRATOR, CERAMIC (10MHz)

************************************************************

1-661-466-11 T.MOTOR BOARD

*************

#11

#12

#13

#14

#15

7-682-552-09 SCREW +B 3X16

7-621-772-20 SCREW +B 2X5

7-624-109-04 STOP RING 5.0, TYPE -E

7-621-775-20 SCREW +B 2.6X5

7-621-772-30 SCREW +B 2X6

************************************************************

1-661-470-11 T.SENS BOARD

************

#16

7-621-255-15 SCREW +P 2X3

************************************************************

< CONNECTOR >

ACCESSORIES & PACKING MATERIALS

CN802 1-506-481-11 PIN, CONNECTOR 2P

CN803 1-506-481-11 PIN, CONNECTOR 2P

*******************************

1-475-654-11 REMOTE COMMANDER (RM-DX220)

1-558-271-11 CORD, CONNECTION (AUDIO) 1.5m

1-777-172-11 CORD, CONNECTION (CONTROL A1) 1m

(CND)

3-810-765-11 MANUAL, COMMONNESS INSTRUCTION

(ENGLISH) (US, AUS)

< PHOTO INTERRUPTER >

IC801 8-749-924-18 PHOTO INTERRUPTER RPI-1391

IC802 8-749-924-18 PHOTO INTERRUPTER RPI-1391

IC803 8-749-924-18 PHOTO INTERRUPTER RPI-1391

3-810-765-21 MANUAL, COMMONNESS INSTRUCTION

(ENGLISH, FRENCH, GERMAN, SPANISH,

DUTCH, SWEDISH, ITALIAN, PORTUGUESE,

CHINESE) (CND, AEP, UK, AED, E, SP)

< RESISTOR >

R801

R802

R803

R804

1-249-416-11 CARBON

1-249-415-11 CARBON

820

680

1/4W

3-862-563-11 MANUAL, INSTRUCTION (ENGLISH) (US, AUS)

3-862-563-21 MANUAL, INSTRUCTION (ENGLISH, FRENCH,

SPANISH) (CND, AEP, UK, E, SP)

************************************************************

3-862-563-31 MANUAL, INSTRUCTION (GERMAN, DUTCH,

ITALIAN, PORTUGUESE) (AEP, UK)

MISCELLANEOUS

**************

3-862-563-41 MANUAL, INSTRUCTION

(SWEDISH, DANISH, FINNISH) (AED)

1-783-364-11 WIRE (FLAT TYPE) (15 CORE)

1-575-042-21 CORD, POWER (US, CND)

1-575-651-21 CORD, POWER (AEP, UK, AED, SP)

1-696-027-11 CORD, POWER (E)

3-862-563-51 MANUAL, INSTRUCTION (CHINESE) (E, SP)

!62

4-981-643-01 COVER, BATTERY (for RM-DX220)

4-984-086-01 BOOKLET (100)

1-696-845-11 CORD, POWER (AUS)

!63

304

!306

M101

1-569-007-11 ADAPTOR, CONVERSION 2P (E)

1-773-183-11 WIRE (FLAT TYPE) (23 CORE)

1-769-069-11 WIRE (FLAT TYPE) (16 CORE)

8-848-379-31 OPTICAL PICK-UP KSM-213BKN/M-N

X-2626-234-1 T. T CHASSIS ASSY (MG) (K) (SPINDLE)

M102

M801

M802

X-2625-769-1 MOTOR GEAR ASSY (MB) (PP) (SLED)

A-4604-847-A MOTOR ASSY (TABLE)

A-4604-847-A MOTOR ASSY (LOADING)

The components identified by Les composants identifiés par une

mark ! or dotted line with marque ! sont critiques pour la

mark ! are critical for safety. sécurité.

Replace only with part num- Ne les remplacer que par une pièce

ber specified.

portant le numéro spécifié.

– 61 –

CDP-CX220

98D0589-1

Published by Quality Assurance Dept.

(Shibaura)

Sony Corporation

Home A&V Products Company

– 62 –

9-922-819-11

Sony DREAM MACHINE ICF CD3IP User Manual
Seagate EE252 SERIES ST980817AM User Manual
Seagate Constellation ST1000NM0021 User Manual
Seagate CHEETAH X15 ST39251LC User Manual
Seagate Backup Plus STCB2000900 User Manual
Samsung SGH D510 User Manual
Rotel RCD 820 User Manual
Philips Audio CD Recorder CDR770 User Manual
Nokia Cell Phone 6210 User Manual
Honeywell VisionPRO TH8000 Series Operating User Manual