Wireless Battery-Powered
Doorbell Kit
ITEM #1001 406 909 &
#1001 406 915
MODEL #216601 & #216602
Use and Care
Guide
TOOLS REQUIRED
HARDWARE INCLUDED
(2) or (4) #4 x 3/4 in.
Screws depending
on model
(1) or (2) Adhesive
Stickers depending
on model
(2) #6 x 3/4 in.
Screws
Phillips screwdriver
Flat Head Screwdriver
(3) AA Batteries
(2) Wall Anchors
Drill
3/16” Drill Bit
5/64” Drill Bit
Installation
ACTIVATING THE PUSH BUTTON BATTERY
INSERTING THE CHIME BATTERIES
1
2
□ Remove the front cover of the push button by inserting a flat
head screwdriver in the slot on the bottom of the button and
pulling up slightly.
□ Remove the battery compartment cover from the back of the
chime.
□ Insert (3) AA batteries as shown in the diagram on the chime
□ Remove the plastic tab from the battery compartment to
and replace the battery compartment cover.
allow connection to the terminal.
□ Snap the front cover onto the base by first hooking the tops
together, then snapping the base on.
□ Repeat for second button if applicable.
SYNCING THE CHIME AND PUSH BUTTON
MOUNTING THE CHIME
3
4
□ Snap the back cover onto the chime.
□ Mark the desired screw locations on a clean wall.
The chime and included push button(s) already come synced.
Follow the steps below if you need to resync, or sync
additional push buttons.
□ Drill a pilot hole on each mark using a 3/16” drill bit and
insert the wall anchors.
□ Press and release the learning button on the inside of the chime.
□ Screw in the included #6 screws and mount the door chime
□ Immediately following, press and release the push button to
hear a 2-note tune. Press and release the push button again
within five seconds to hear another tune. Continue pressing
and releasing the push button until you reach the desired tune.
To set that tune, do not push the push button for five seconds.
to the screws.
Learning
mode
button
HOMEDEPOT.COM
Please contact 1-855-556-1852 for further assistance.
MOUNTING THE PUSH BUTTON
RESYNCING THE CHIME AND PUSH BUTTON
5
6
□ Remove the front cover from the base by following step 1.
This step is optional only if restarting and resyncing the chime
is needed.
□ Mount the push button base to a clean wall or door jamb
with included #4 screws or mounting tape. If mounting with
screws, predrill a pilot hole through the push button base in
the desired location using a 5/64 in. drill bit.
□ Press and hold the learning mode button on the chime until
you hear a ding sound. The chime is now reset and ready to
be resynced.
□ Snap the push button cover onto the base by first hooking
□ Follow step 3 to sync the chime and push button.
the tops together, then snapping the base on.
Safety Information
You are cautioned that changes or modifications not expressly approved by the party responsible for compliance
could void your authority to operate the equipment.
WARNING: Keep batteries out of reach of
children.
This Device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired
operation.
Battery Safe Handling:
□
□
□
□
Do Not Mix Old And New Batteries.
Do Not Mix Alkaline, Standard (Carbon – Zinc), or Rechargeable (Nickel – Cadmium) Batteries.
Battery must be recycled or disposed of properly.
Keep battery away from children. If swallowed, promptly see a doctor. Do not open battery, dispose of
in fire, put in backwards, or short circuit—it may ignite, explode, leak or get hot causing injury.
Specifications
216601
Doorbell Type
Wireless
1
Number of Push Buttons
Included Hardware
Finished Product Dimensions
Transmission Range
Number of Sounds
Chime Power Source
Push Button Power Source
(2) #4 x ¾ in. Screws, (1) 18x31mm Adhesive Sticker, (2) #6 x ¾ in. Screws, and (2) Wall Anchors
6 in. Height x 6 in. Width x 1.5 in. Depth
100 feet
2
(3) AA Batteries (not included)
CR2032 Battery (included)
216602
Doorbell Type
Wireless
Number of Push Buttons
Included Hardware
Finished Product Dimensions
Transmission Range
Number of Sounds
Chime Power Source
Push Button Power Source
2
(4) #4 x ¾ in. Screws, (2) 18x31mm Adhesive Stickers, (2) #6 x ¾ in. Screws, and (2) Wall Anchors
6 in. Height x 6 in. Width x 1.5 in. Depth
100 feet
2
(3) AA Batteries (not included)
CR2032 Battery (included)
HOMEDEPOT.COM
Please contact 1-855-556-1852 for further assistance.
Troubleshooting
Problem
Possible Cause
Solution
Chime does not sound when push button is pressed.
Push button battery has not been
activated.
Confirm the activation tab has been removed and
the battery is seated properly in the button.
The chime and push button are out
of transmission range.
Move the chime closer to the push button
location. Ensure there are no metallic objects or
concrete walls hindering the signal.
Push button battery needs to be
replaced.
Replace the Push Button battery with a CR2032
Lithium Coin battery.
Chime batteries need to be
replaced.
Replace the chime batteries with (3) AA batteries.
Chime is sounding without the push button being pushed.
An outside signal is interfering with Resync the chime and push button following the
the signal between the chime and
push button.
steps in the instructions.
Warranty
WHAT IS COVERED
The Warrantor is pleased to extend this Warranty to you, the original consumer/end user (“Consumer”) of the doorbell products and listed by model
number below (“Doorbell Product”). This Warranty is valid for any Doorbell Product used in standard residential applications, and may not be assigned or
transferred by you.
Only doorbell products with the following model numbers are covered by this Warranty: 216589, 216590, 216591, 216592, 216593, 216594, 216595,
216596, 216597, 216598, 216599, 216600, 216601, 216602, 216603, 216604 and 216605.
For a period of one (1) year from the date of purchase, Warrantor, at its sole option, will repair, replace or refund the purchase price for any Doorbell Product
used in a standard residential application that malfunctions due to factory defective parts or defective workmanship in the manufacture or assembly of the
Doorbell Product.
WHAT IS NOT COVERED
Warrantor shall have no further liability or obligation except as expressly stated herein.
This Warranty does not apply to any Doorbell Product that has been abused, misused, modified, subjected to abnormal use conditions, stored improperly
prior to installation, or otherwise used in any way not intended by Warrantor.
This Warranty is limited to repair, replacement or refund as set forth above and any additional reimbursement is expressly excluded from this Warranty,
including but not limited to reimbursement for inconvenience, installation costs, loss of use, return shipping charges, and batteries or other expendable
items.
If a claim is made under this Warranty on a product that is no longer available, Warrantor reserves the right to provide a similar product of comparable
quality and value.
To make a claim under this Warranty, the Consumer must, within ninety (90) days of actual or constructive knowledge of damage covered by this Warranty,
return the product to your local The Home Depot store, or call Customer Service at 1-855-556-1852.
Warrantor does not make any implied warranty of merchantability or fitness of the product for a particular purpose. There are no other warranties that
extend beyond the description on the face hereof.
This Warranty gives you specific legal rights and you may have additional rights under applicable law.
HOMEDEPOT.COM
Please contact 1-855-556-1852 for further assistance.
|