3-856-035-11 (1)
FM/MW/LW
Cassette Car
Stereo
EN
Operating Instructions
XR-3208MK2
1995 by Sony Corporation
Actual total number:
Sony XR-3208MK2 (E) 3-856-035-11 (1)
Notes on Cassettes
Table of Contents
Cassette care
Detaching and Attaching the Front Panel ............ 4
Setting the Clock ...................................................... 5
•Do not touch the tape surface of a cassette, as
any dirt or dust will contaminate the heads.
•Keep cassettes away from equipment with
built-in magnets such as speakers and
amplifiers, as erasure or distortion of the
recorded tape could occur.
•Do not expose cassettes to direct sunlight,
extremely cold temperatures, or moisture.
•When the tape is played back for a long
period, the cassette shell may become warm
because of the built-in power amplifier. This
is not a sign of a malfunction.
Cassette Player Operation
Listening to Tape Playback .................................... 5
Ejecting the Cassette ................................................ 5
Fast-winding the Tape ............................................ 6
Radio Reception
Searching for Stations Automatically
— Automatic Tuning ......................................... 6
Notes on Cassette Deck Tape Heads
•Long use of cassette tapes contaminates the
tape head causing poor sound quality or
complete sound dropout. Therefore, we
recommend cleaning the tape head once a
month or so with the separately available
Sony Cassette Cleaning Set. If the sound does
not improve after using a cleaning cassette,
please consult your nearest Sony dealer.
•In case of old or inferior cassette tapes, the
tape head gets contaminated much more
quickly. Depending on the tape, one or two
playbacks may cause poor sound.
If FM Stereo Reception is Poor
— Monaural Mode .............................................. 6
Tuning in by Adjusting the Frequency
— Manual Tuning ............................................... 7
Memorizing Stations Automatically
— Automatic Memory Function ...................... 7
Memorizing Only the Desired Stations ................ 7
Receiving the Memorized Stations ....................... 7
EN
Other Functions
Cassettes longer than 90 minutes
Adjusting the Sound Characteristics .................... 8
The use of cassettes longer than 90 minutes is
not recommended except for long continuous
play. The tapes used for these cassettes are
very thin and tend to be stretched easily.
Frequent playing and stopping of these tapes
may cause them to be pulled into the cassette
deck mechanism.
Enjoying Bass and Treble at Low Volume
— Loudness Function ......................................... 8
Muting the Beep Tone ............................................. 8
Maintenance ............................................................. 8
Button Locations ...................................................... 9
Specifications .......................................................... 10
Troubleshooting Guide ......................................... 11
3
Actual total number
Sony XR-3208MK2 (E) 3-856-035-11 (1)
• Do not expose the front panel to direct sunlight, heat
sources such as hot air ducts or leave it in a humid place.
Never leave it on the dashboard etc. of a car parked in
direct sunlight where there may be a considerable rise in
temperature inside the car.
Detaching and Attaching
the Front Panel
The front panel of this unit can be detached in
order to prevent the unit from being stolen.
Caution alarm
If you turn the ignition key to the OFF position
without removing the front panel, the caution
alarm will be activated and a beep tone will be
heard for a few seconds.
Detaching the Front Panel
Before detaching the front panel, be sure to
OFF
press the
button first. Then press the
RELEASE button to open up the front panel
and detach the panel by pulling it towards you
as illustrated.
RELEASE button
EN
Be sure not to drop the panel after detaching it
from the unit.
Attaching the Front Panel
Apply the right side of the front panel to the
unit by attaching part A of the front panel to
part B of the unit as illustrated, then swing
the left side into the unit until it clicks.
A
B
Notes
• Make sure that the front panel is the right way up when
attaching it to the unit as it cannot be attached upside
down.
• Do not press the front panel hard against the unit when
attaching it to the unit. It can easily be attached by
pressing it lightly against the unit.
• When you carry the front panel with you, put it in the
supplied front panel case.
• Do not press hard or give excessive pressure to the
display windows of the front panel.
• Before removing the front panel, be sure to turn the
power off. However, if you press the RELEASE button to
detach the panel while the unit is still turned on, the
power will be automatically turned off in order to protect
the speakers from being damaged.
4
Actual total number
Sony XR-3208MK2 (E) 3-856-035-11 (1)
Cassette Player
Operation
Setting the Clock
The clock has a 24-hour digital indication.
For example, setting it to 10:08
1 Display the time.
DSPL
Listening to Tape Playback
After inserting the cassette, playback
will start automatically.
(Press the
button during unit
operation.)
DSPL
2 Press the
seconds.
button for more than two
The hour digit(s) blinks.
To change the tape direction,
press both the 0 and the ) buttons at the
same time.
Set the hour digits.
SEL
–
+
(to go back) (to go forward)
EN
Indication of Tape Transport Direction
SEL
The side facing up is being played.
3 Press the
button momentarily.
The minute digits blink.
The side facing down is being played.
Tape playback automatically changes
direction at the end of the tape.
Set the minute digits.
SEL
–
+
Note
Before turning off the unit, eject the tape to avoid tape
damage.
(to go back) (to go forward)
Ejecting the Cassette
DSPL
4 Press the
button momentarily.
Press the
button to stop playback and eject
the cassette.
The clock activates.
Note
The clock cannot be set unless the power is turned on. Set
the clock after you turn on the radio, or during tape
playback.
5
Actual total number
Sony XR-3208MK2 (E) 3-856-035-11 (1)
Fast-winding the Tape
Radio Reception
Direction
To advance
To rewind
indicator*
(
Searching for Stations
Automatically
— Automatic Tuning
9
1 Select the desired band.
A.MEM
To resume playback, press the other fast-
winding button partially until the locked
button is released.
TUNER
FM1 n FM2n FM3 n
MW n LW n FM1
* The 9 or ( indicator will flash while fast-winding the
tape.
2 Press either side of the SEEK/MANU
button momentarily to search for the
next station (automatic tuning).
SEEK/MANU
SEEK/MANU
–
+
–
+
EN
For lower
frequencies
For higher
frequencies
The scanning stops when a station is received.
Press either side of the button repeatedly until
the desired station is received.
When an FM stereo program with a sufficient
signal strength is tuned in,
ST
the “ST” indication will appear.
To avoid the automatic tuning from stopping on
stations too frequently (local seek mode), press
the SENS button momentarily to get the “LCL”
indication.
Only the stations with relatively strong signals will be
tuned in. The local seek mode functions only when the
automatic tuning is in operation.
If FM Stereo Reception is
Poor — Monaural Mode
SENS
Press the
button momentarily.
n “MONO” appears on the display.
The sound will improve, but it will become
monaural.
6
Actual total number
Sony XR-3208MK2 (E) 3-856-035-11 (1)
Tuning in by Adjusting the
Frequency — Manual Tuning
Memorizing Only the
Desired Stations
1 Select the desired band.
1 Select the desired band.
A.MEM
A.MEM
TUNER
TUNER
FM1 n FM2n FM3 n
MW n LW n FM1
FM1 n FM2n FM3 n
MW n LW n FM1
2 Press and hold either side of the SEEK/
MANU button.
2 Tune in the station which you wish to
store on the preset number button.
Release the button when the desired station
is received.
3 Press and hold the desired preset
SEEK/MANU
SEEK/MANU
–
+
–
+
1
6
number button (
to
) for about
two seconds until you hear a beep tone.
For lower
frequencies
For higher
frequencies
The number of the pressed preset number
button appears in the display window.
PREVENT ACCIDENTS!
ST
When tuning in during driving, use the
automatic tuning and the memory preset
tuning instead of the manual tuning.
FM
EN
Up to 6 stations on each band (FM1, FM2, FM3, MW and
LW) can be stored on the preset number buttons in the
order of your choice. Therefore, 18 stations can be
memorized on FM.
If you try to store another station on the same preset
number button, the previously stored station will be
erased.
Memorizing Stations
Automatically
— Automatic Memory Function
Stations with the clearest reception are
automatically searched and memorized on each
band (FM1, FM2, FM3, MW and LW). Up to 6
stations on each band can be stored on the
preset number buttons 1 to 6 in the order of
band frequency.
Receiving the Memorized
Stations
1 Select the desired band.
1 Select the desired band.
A.MEM
A.MEM
TUNER
TUNER
FM1 n FM2n FM3 n
MW n LW n FM1
FM1 n FM2n FM3 n
MW n LW n FM1
2 Press the TUNER/A.MEM button for more
than two seconds.
2 Press momentarily the preset number
1
6
button (
to
) on which the
A.MEM
desired station is stored.
TUNER
Note
If you press the preset number button for more than two
seconds, the currently received station will be memorized.
To receive the previously memorized station, make sure
that the preset number button is pressed only
momentarily.
The unit will be start scanning the selected
band and memorize the tuned stations on
the preset number button 1 through 6
automatically.
7
Actual total number
Sony XR-3208MK2 (E) 3-856-035-11 (1)
Maintenance
Cleaning the Connectors
Other Functions
The unit may not function properly if the
connectors between the unit and the front
panel are not clean. In order to prevent this,
open the front panel by pressing the RELEASE
button, then detach it and clean with a cotton
swab dipped in alcohol. Do not apply too
much force. Otherwise, the connector may get
damaged.
Adjusting the Sound
Characteristics
1 Select the item you want to adjust by
SEL
pressing the
button repeatedly.
VOL (volume) n BAS (bass) n TRE
(treble) n BAL (balance) n FAD (fader)
n VOL (volume)
Main unit
2 Adjust the selected item by pressing
+
–
either the
or
button.
Adjust within three seconds after selecting.
(After three seconds the button will again
serve as volume control button.)
EN
Back of the front panel
Enjoying Bass and Treble
at Low Volume
— Loudness Function
LOUD
Press the
button. n “LOUD” will
appear on the display.
Bass and treble will be boosted. To cancel,
press again.
Muting the Beep Tone
5
Press the
the
button while pressing
SEL
button.
To reactivate the beep tone, press these buttons
once more.
8
Actual total number
Sony XR-3208MK2 (E) 3-856-035-11 (1)
Button Locations
DSPL
LOUD
1
2
3
4
5
6
RELEASE
A.MEM
SEEK/MANU
SEL
TUNER
SENS
OFF
–
+
–
+
Refer to the pages in r for details.
EN
8 RELEASE (front panel release) button
48
1 Display window
2 SEL (control mode select) button 58
–
+
9
(volume/bass/treble/
balance/fader control) buttons 58
3 DSPL (display mode change/time set)
button 5
0 SEEK/MANU button 67
4 6 (eject) button 5
!¡ TUNER/A.MEM (radio on • band select/
5 During radio reception:
automatic memory) button 67
Preset number buttons 7
!™ SENS (sensitivity adjust) button 6
6 0/) (fast winding)/DIR (tape
transport direction change) buttons
56
!£ OFF button 4
7 LOUD (loudness) button 8
9
Actual total number
Sony XR-3208MK2 (E) 3-856-035-11 (1)
Specifications
Cassette player section
General
Tone controls
Tape track
4-track 2-channel stereo
Bass ±8 dB at 100 Hz
Treble ±8 dB at 10 kHz
12 V DC car battery
(negative ground)
Approx. 186 × 57 × 170 mm
(w/h/d) not incl.
projecting parts and
controls
Approx. 182 × 53 × 155 mm
(w/h/d) not incl.
projecting parts and
controls
Wow and flutter
Frequency response
Signal-to- noise ratio
0.13 % (WRMS)
30 – 15,000 Hz
55 dB
Power requirements
Dimensions
Tuner section
FM
Tuning range
Antenna terminal
87.5 – 108.0 MHz
External antenna connector
Mounting dimension
Intermediate frequency 10.7 MHz
Usable sensitivity
Selectivity
Signal-to-noise ratio
12 dBf
70 dB at 400 kHz
65 dB (stereo),
68 dB (mono)
Mass
Supplied accessories
Approx. 1.2 kg
Front panel case (1)
Harmonic distortion at 1 kHz
Design and specifications are subject to change without
notice.
0.5% (stereo),
0.3% (mono)
35 dB at 1 kHz
30 – 15,000 Hz
2 dB
Separation
Frequency response
Capture ratio
EN
MW/LW
Tuning range
MW: 531 – 1,602 kHz
LW : 153 – 281 kHz
External antenna connector
Antenna terminal
Intermediate frequency 450 kHz
Sensitivity MW: 30 µV
LW : 50 µV
Power amplifier section
Outputs
Speaker outputs
(sure seal connectors)
4 – 8 ohms
Speaker impedance
Maximum power output 15 W × 4 (at 4 ohms)
10
Actual total number
Sony XR-3208MK2 (E) 3-856-035-11 (1)
Troubleshooting Guide
The following checklist will assist in the correction of most problems which you may encounter with
your unit.
Before going through the checklist below, refer to the connection and operating procedures.
General
Problem
Cause/Solution
+
No sound
•Adjust the volume with the
button.
•Set the fader control to the center position for 2-speaker
systems.
Remove the front panel and clean the connectors. See “Cleaning
the Connectors” of “Maintenance” for details.
Indications do not appear in the
display window.
Tape playback
Problem
Cause/Solution
Playback sound is distorted.
Contamination of the tape head. n Clean the head.
EN
Radio reception
Problem
Cause/Solution
Preset tuning is not possible.
•Memorize the correct frequency.
•The broadcast is too weak.
Automatic tuning is not possible. The broadcast is too weak. n Use the manual tuning.
The “ST” indication flashes.
•Tune in precisely.
•The broadcast is too weak. n Press the SENS button to enter
the MONO mode.
11
Actual total number
Sony XR-3208MK2 (E) 3-856-035-11 (1)
Sony Corporation Printed in Malaysia
Actual total number:
Sony XR-3208MK2 (E) 3-856-035-11 (1)
|