HDR-SR11/SR11E/SR12/SR12E
RMT-835
LEVEL
2
SERVICE MANUAL
US Model
Canadian Model
AEP Model
Ver. 1.0 2008.01
Revision History
UK Model
North European Model
E Model
Australian Model
Hong Kong Model
Chinese Model
Korea Model
Tourist Model
Japanese Model
Photo: HDR-SR12
Link
SPECIFICATIONS
DISASSEMBLY
SCHEMATIC DIAGRAMS
PRINTED WIRING BOARDS
REPAIR PARTS LIST
MODEL INFORMATION TABLE
SERVICE NOTE
BLOCK DIAGRAMS
FRAME SCHEMATIC DIAGRAM
• Precaution on Replacing the VC-516 Board
• Precaution on Replacing the CABINET (G(900)) ASSY
The components identified by Les composants identifiés par une
mark 0 or dotted line with marque 0 sont critiques pour la
mark 0 are critical for safety. sécurité.
Replace only with part num- Ne les remplacer que par une pièce
ber specified.
portant le numéro spécifié.
DIGITAL HD VIDEO CAMERA RECORDER
2008A0800-1
© 2008.01
Published by Kohda TEC
HDR-SR11/SR11E/SR12/SR12E_L2
Sony EMCS Co.
9-852-254-31
These specifications are extracted from instruction manual of
HDR-SR11/SR12.
ENGLISH
JAPANESE
SPECIFICATIONS
System
Input/Output connectors
A/V Remote Connector: Component/video and
audio output jack
Handycam Station DCRA-C210
Input/Output connectors
Video compression format: AVCHD (HD)/
MPEG2 (SD)/JPEG (Still images)
A/V OUT jack: Component/video and audio
output jack
USB jack: mini-B
Audio compression format: Dolby Digital 2/5.1ch
Dolby Digital 5.1 Creator
Video signal: NTSC color, EIA standards
1080/60i specification
Hard disk: HDR-SR11: 60 GB
HDR-SR12: 120 GB
HDMI OUT jack: HDMI Type C mini connector
Headphone jack: Stereo minijack (∅ 3.5mm)
MIC input jack: Stereo minijack (∅ 3.5mm)
USB jack: mini-B
AC Adaptor AC-L200/L200B
Power requirements: AC 100 V - 240 V, 50/60 Hz
Current consumption: 0.35 - 0.18 A
Power consumption: 18 W
LCD screen
Image: 8.0 cm (3.2 type, aspect ratio 16:9)
Total dot number: 921 600 (1 920 × 480)
When measuring media capacity, 1 GB equals
1 billion bytes, a portion of which is used for
data management.
Output voltage: DC 8.4 V*
Recording format: Movie (HD): AVCHD 1080/
60i
Movie (SD): MPEG2-PS
Still image: Exif Ver.2.2*
Viewfinder: Electric viewfinder: color
Image device: 5.8 mm (1/3.13 type) CMOS sensor
Recording pixels (still image, 4:3):
Max. 10.2 mega (3 680 × 2 760) pixels**
Gross: Approx. 5 660 000 pixels
Effective (movie, 16:9):
General
Operating temperature: 0 ˚C to + 40 ˚C (32 ˚F to
104 ˚F)
Storage temperature: -20 ˚C to + 60 ˚C (-4 ˚F to +
140 ˚F)
Dimensions (approx.): 48 × 29 × 81 mm
(1 15/16 × 1 3/16 × 3 1/4 in.) (w/h/d)
excluding the projecting parts
Mass (approx.): 170 g (6.0 oz) excluding the
power cord (mains lead)
Power requirements: DC 6.8 V/7.2 V (battery
pack)
DC 8.4 V (AC Adaptor)
Average power consumption: During camera
recording using the viewfinder with normal
brightness:
Hard disk:
HD: 4.5 W SD: 3.6 W
“Memory Stick PRO Duo”:
HD: 4.4 W SD: 3.6 W
During camera recording using the LCD with
normal brightness:
Hard disk:
HD: 4.8 W SD: 4.0 W
“Memory Stick PRO Duo”:
HD: 4.6 W SD: 3.9 W
Approx. 3 810 000 pixels
Effective (still image, 16:9):
Approx. 3 810 000 pixels
Effective (still image, 4:3):
* See the label on the AC Adaptor for other
specifications.
Rechargeable battery pack NP-FH60
Approx. 5 080 000 pixels
Maximum output voltage: DC 8.4 V
Output voltage: DC 7.2 V
Capacity: 7.2 Wh (1 000 mAh)
Type: Li-ion
Lens: Carl Zeiss Vario-Sonnar T
12 × (Optical), 24 ×, 150 × (Digital)
Focal length: F1.8 ~ 3.1
Operating temperature: 0 ˚C to + 40 ˚C (32 ˚F to
104 ˚F)
Storage temperature: -20 ˚C to + 60 ˚C (-4 ˚F to +
140 ˚F)
Dimensions (approx.): 83 × 76 × 138 mm
(3 3/8 × 3 × 5 1/2 in.) (w/h/d)
Filter diameter: 37 mm (1 1/2 in.)
f=4.9 ~ 58.8 mm (7/32 ~ 2 3/8 in.)
When converted to a 35 mm still camera
For movies: 40 ~ 480 mm (1 5/8 ~ 19 in.)
(16:9)
Design and specifications of your camcorder and
accessories are subject to change without notice.
For still images: 37 ~ 444 mm (1 1/2 ~ 17 1/2
in.) (4:3)
including the projecting parts
83 × 76 × 138 mm
(3 3/8 × 3 × 5 1/2 in.) (w/h/d)
including the projecting parts, and the supplied
rechargeable battery pack attached
Color temperature: [AUTO], [ONE PUSH],
[INDOOR] (3 200 K),
[OUTDOOR] (5 800 K)
Minimum illumination: 5 lx (lux) ([AUTO SLW
SHUTTR] [ON], Shutter speed 1/30 sec)
0 lx (lux) (during NightShot function)
Mass (approx.): HDR-SR11: 560 g (1 lb 3 oz)
main unit only
640 g (1 lb 6 oz) including the supplied
rechargeable battery pack
HDR-SR12: 570 g (1 lb 4 oz) main unit only
650 g (1 lb 6 oz) including the supplied
rechargeable battery pack
* “Exif” is a file format for still images,
established by the JEITA (Japan
Electronics and Information Technology
Industries Association). Files in this
format can have additional information
such as your camcorder’s setting
information at the time of recording.
**The unique pixel array of Sony’s ClearVid
CMOS sensor and image processing
system (BIONZ) allows for still image
resolution equivalent to the sizes
described.
HDR-SR11/SR11E/SR12/SR12E_L2
— 3 —
ENGLISH
JAPANESE
概略仕様
アダプター
AC-L200/L200B
システム
映像圧縮方式：AVCHD
（静止画
音声圧縮方式：Dolby Digital2/5.1ch
ドルビーデジタル クリエーター搭載
入 出力端子
AC
/
電源
消費電力：18 W
定格出力：
AC 100 V - 240 V 50/60 Hz
： 、
（
HD
）
/MPEG2
（
SD /JPEG
）
A/Vリモート端子：コ ンポーネント、映像音声出力兼
）
用端子
HDMI OUT端子：HDMIタイプ
C
ミニ端子
DC 8.4 V *
動作温度： ℃～+40
保存温度：－ 20 ℃～+60
外形寸法：約
5.1
ヘッドホン端子：ステレオミニジャック（¯ 3.5 mm
）
0
℃
映像信号：NTSCカラー、EIA標準方式
入力端子：ス テレオミニジャック（
MIC
）
¯ 3. 5 mm
℃
方式
1080/60i
USB端子：mini-B
×
×
（最大突起部をのぞ
48 29 81 mm
ハードディスク：HDR-SR11：
60 GB
く（）幅×高さ×奥行き）
：
HDR-SR12 120 GB
容量は、1GB
10億バイトで計算
液晶画
サイズ：8.0 cm
総ドット数：921 600ドット
1 920×縦480
面
質量：約 （本体のみ）
170 g
を
した場合の数
画
面
（
3.2型、アスペクト比16
： ）
9
値です。また管理用ファイルなどを含むため、実
際使用できる容量は若干減少する場合がありま
す。
* その他の仕様については
をご覧ください。
アダプターのラベル
AC
横
リチャージャブルバッテリーパック
電源
動画 記録方式：動 画
：
HD AVCHD 1080/60i
部、その他
電源電圧：バッテリー端子入力 6.8 V/7.2 V
動画 SD
：
MPEG2-PS
NP-FH60
静止画 記録方式：
Exif Ver.2.2*
最大電圧：
DC 8.4 V
端子入力
DC
8.4 V
ファインダー：電 子 フ ァインダー：カ ラ ー
撮像素子：5.8 mm
1/3.13型）CMOSセンサー
記録画 素数：静止画 時最大 万画 素相当
公称電圧：DC 7.2 V
消費電力：ファインダー使用時、明るさ標準：
ハードディスク：
（
容量：7.2 Wh
（
1 000 mAh
）
1 020
**
使用電池：
Li-ion
HD
：
4.5 W SD
：
3.6 W
（
×
）（ ： 時）
3 680 2 760 4 3
“メモリースティック PRO デュオ”：
総画 素数：約566万画
素
本機やアクセサリーの仕様および外観は、改良のた
め予告なく変更することがありますが、ご了承くだ
さい。
：
：
HD 4.4 W SD 3.6 W
動画 時有効画 素数（ ： ）：約
万画
素
16 9
静止画 時有効画 素数（16
静止画 時有効画 素数（
381
）：約381万画
）：約508万画
液晶画
面使用時、明るさ標準：
：
：
3
9
素
ハードディスク：
4
素
：
：
HD 4.8 W SD 4.0 W
ズームレンズ：カ ール ツァイス バリオゾナー
T
“メモリースティック PRO デュオ”：
12倍（光学）、24倍、150倍（デジタル）
フィルター径
～
F1.8 3.1
：
：
HD 4.6 W SD 3.9 W
37 mm
動作温度：
0
℃～+40
℃
保存温度：－
℃～
℃
20
+60
～
f=4.9 58.8 mm
カメラ換算
では動画 撮影時
35mm
～
外形寸法：
×
×
83 76 138 mm
40 480 mm
静止画 撮影時：
（ ： ）
（
16
：
9
）
（突起部を含む）
（幅×高さ×奥行き）
～
37 444 mm 4 3
色温度切り換え：［オート］、［ワンプッシュ］、［屋
（幅×高さ×奥行き）
×
×
83 76 138 mm
（突起部を含む、付属バッテリー装着 状態）
3 200 K）、［屋
内］
（
外（］5 800 K）
本体質量：HDR-SR11：約560 g（本体のみ）
最低被写体照度： （ルクス（）［オートスロシャッ
5 lx
HDR-SR12：約 570 g（本体のみ）
タ［］入］、［シャッタースピード］1/30秒）
0 lx（ルクス（）NightShot時）
撮影時総質量：HDR-SR11：約640 g（付属バッテ
リー含む。）
*
（社）電子情報技術産業協会（JEITA）にて制定
された、撮影情報などの付帯情報を追加する
ことができる静止画 用のファイルフォーマッ
ト。
：約
（付属バッテリー含む。）
HDR-SR12 650 g
ハンディカムステーション
DCRA-C210
**
ソニー独自のクリアビッド
の画 素配列と画 像処理システム
BIONZ
センサー
によ
CMOS
入
/
出力端子
り、静止画 は表記の記録サイズを実現してい
ます。
端子：コンポーネント、映像音声出力兼用端
A/VOUT
子
端子：
USB mini-B
HDR-SR11/SR11E/SR12/SR12E_L2
— 4 —
Model information table
Model
HDR-SR11
HDR-SR11E
HDR-SR12
HDR-SR12E
AEP, UK, NE, E,
CH, HK, AUS, JE
AEP, UK, NE, E,
CH, HK, AUS, JE
Destination
US, CND, E, KR, JE, J
US, CND, E, KR, JE, J
Color system
Hard disk
NTSC
60GB
PAL
NTSC
PAL
60GB
120GB
120GB
•
Abbreviation
AUS : Australian model
CH : Chinese model
CND : Canadian model
HK : Hong Kong model
J
: Japanese model
JE : Tourist model
KR : Korea model
NE : North European model
HDR-SR11/SR11E/SR12/SR12E_L2
— 5 —
ENGLISH
JAPANESE
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
SAFETY-RELATED COMPONENT WARNING!!
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINEWITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
Unleaded solder
1. Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
2. Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
3. Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
4. Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit Board Repairing
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Keep the temperature of the soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
HDR-SR11/SR11E/SR12/SR12E_L2
— 6 —
ENGLISH
JAPANESE
注意
電池の交換は，正しく行わないと破裂する恐れがあり
ます。電池を交換する場合には必ず同じ型名の電池
又は同等品と交換してください。
サービス，点検時には次のことにご注意下さい。
6. フレキシブルプリント基板の取扱いについて
1. 注意事項をお守りください。
• コテ先温度を270℃前後にして行なって下さい。
• 同一パターンに何度もコテ先を当てないで下さい。
（３回以内）
サービスのとき特に注意を要する個所については，
キャビネット，シャーシ，部品などにラベルや捺印で
注意事項を表示しています。これらの注意書き及び取
扱説明書等の注意事項を必ずお守り下さい。
2. 指定部品のご使用を
• パターンに力が加わらないよう注意して下さい。
7. 無鉛半田について
無鉛半田を使用している基板には，無鉛（LeadꢀFree）を
意味するレッドフリーマークがプリントされています。
（注意：基板サイズによっては，無鉛半田を使用して
いてもレッドフリーマークがプリントされて
いないものがあります）
セットの部品は難燃性や耐電圧など安全上の特性を
持ったものとなっています。従って交換部品は，使用
されていたものと同じ特性の部品を使用して下さい。
特に回路図，部品表に0印で指定されている安全上重要
な部品は必ず指定のものをご使用下さい。
：レッドフリーマーク
3. 部品の取付けや配線の引きまわしはもとどおりに
安全上，チューブやテープなどの絶縁材料を使用した
り，プリント基板から浮かして取付けた部品がありま
す。また内部配線は引きまわしやクランパによって発
熱部品や高圧部品に接近しないよう配慮されています
ので，これらは必ずもとどおりにして下さい。
4. サービス後は安全点検を
無鉛半田には，以下の特性があります。
• 融点が従来の半田よりも約40℃高い。
従来の半田こてをそのまま使用することは可能です
が，少し長めにこてを当てる必要があります。
温度調節機能のついた半田こてを使用する場合，約
350℃に設定して下さい。
注意：半田こてを長く当てすぎると，基板のパター
ン（銅箔）がはがれてしまうことがあります
ので，注意して下さい。
サービスのために取外したネジ，部品，配線がもとど
おりになっているか，またサービスした個所の周辺を
劣化させてしまったところがないかなどを点検し，安
全性が確保されていることを確認して下さい。
5. チップ部品交換時の注意
• 粘性が強い
従来の半田よりも粘性が強いため，IC端子などが半田
ブリッジしないように注意して下さい。
• 従来の半田と混ぜて使用可能
• 取外した部品は再使用しないで下さい。
• タンタルコンデンサのマイナス側は熱に弱いため交
換時は注意して下さい。
無鉛半田には無鉛半田を追加するのが最適ですが，
従来の半田を追加しても構いません。
HDR-SR11/SR11E/SR12/SR12E_L2
— 7 —
ENGLISH
JAPANESE
1. SERVICE NOTE
1-1. POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4V), the power is shut off so
that the unit cannot operate.
These following method is available to prevent this.
Method:
Use the AC power adaptor (AC-L200/L200B).
1-2. SELF-DIAGNOSIS FUNCTION
1-2-1. Self-diagnosis Function
1-2-2. Self-diagnosis Display
When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the Viewfinder or the LCD
screen what to do. This function consists of two display; self-
diagnosis display and service mode display.
When problems occur while the unit is operating, the counter of the
Viewfinder or the LCD screen shows a 4-digit display consisting of
an alphabet and numbers, which blinks at 3.2 Hz. This 5-character
display indicates the “repaired by:”, “block” in which the problem
occurred, and “detailed code” of the problem.
Details of the self-diagnosis functions are provided in the Instruction
manual.
Viewfinder or LCD screen
C : 3 1 : 1 1
Blinks at 3.2Hz
1 1
C
3 1
Detailed Code
Repaired by:
Block
C : Corrected by customer
H : Corrected by dealer
E : Corrected by service
engineer
Indicates the appropriate
step to be taken.
E.g.
Refer to “1-2-3. Self-diagnosis Code Table”.
31 ....Reload the tape.
32 ....Turn on power again.
HDR-SR11/SR11E/SR12/SR12E_L2
1-1
ENGLISH
JAPANESE
1-2-3. Self-diagnosis Code Table
Self-diagnosis Code
Block
Function
Detailed
Code
Symptom/State
Correction
C
C
0
1
4
3
0
0
0
1
Non-standard battery is used.
Use the InfoLITHIUM battery.
“Memory Stick Duo” is unformatted.
“Memory Stick Duo” is broken.
Format the “Memory Stick Duo”.
Insert a new “Memory Stick Duo”.
Remove the power source. Reconnect it again and operate your
camcorder again
C
C
1
3
3
2
0
6
2
0
Disc access error
Retry turn the power on by the power switch. If it does not
recover, check the focus MR sensor of lens block (pin w;, wa of
CN5103 on the LD-230 board). If it is OK, check the focus
motor drive IC (IC5201 on the LD-230 board).
Difficult to adjust focus
(Cannot initialize focus)
E
E
2
3
0
1
0
0
0
0
Flash memory data are rewritten.
Drive fault
Make flash memory data correct value. (Note 1)
Inspect or replacement of the hard disk drive.
Inspect the lens block zoom MR sensor (pin qh, qj of CN5103
on the LD-230 board) when zooming is performed when the
zoom lever is operated, and the zoom motor drive circuit
(IC5201 on the LD-230 board) when zooming is not performed.
Zoom operations fault
(Cannot initialize zoom lens.)
E
E
6
6
1
1
1
1
0
1
The abnormalities in initialization of
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
Check both C: 32: 60 and E: 61: 10 of the self-diagnosis code.
Handshake correction function does not
work well. (With PITCH angular
velocity sensor output stopped.)
Inspect PITCH angular velocity sensors (SE9001 on the FR-278
board) peripheral circuits.
E
E
6
6
2
2
0
0
0
1
Handshake correction function does not
work well. (With YAW angular velocity
sensor output stopped.)
Inspect YAW angular velocity sensors (SE9002 on the FR-278
board) peripheral circuits.
Refer to [1-3-1. E : 62 : 02 (Abnormality of IC for Steadyshot)
Occurred].
E
E
E
E
E
6
6
6
6
6
2
2
2
2
2
2
0
0
1
1
1
2
3
0
1
2
Abnormality of IC for steadyshot.
IC for steadyshot and micro controller
communication abnormality among.
Inspect the steadyshot circuit (IC5501 on the LD-230 board).
Replacement of lens block. If an error occurs again, replace the
LD-230 board. (Note 2)
Shift lens initializing failure.
Shift lens overheating (Pitch)
Refer to [1-3-2. E : 62 : 11 (Shift Lens Overheating (Pitch))
Occurred].
Shift lens overheating (Yaw)
Refer to [1-3-3. E : 62 : 12 (Shift Lens Overheating (Yaw))
Occurred].
Refer to [1-3-4. E : 62 : 20 (Abnormality of Thermistor)
Occurred].
E
E
E
6
9
9
2
0
0
0
1
0
Abnormality of thermistor.
1
4
Abnormality when flash is being charged. Checking of flash unit or replacement of flash unit.
Fault of writing or erasing the
Inspect the flash memory (IC2101 on the VC-516 board).
flash memory
Note 1 : Refer to Service Manual, ADJ (“1-3. DESTINATION DATA WRITE”).
Note 2 : When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
HDR-SR11/SR11E/SR12/SR12E_L2
1-2
ENGLISH
JAPANESE
1-3. METHOD OF COPING WITH SHIFT LENS ERROR
about 330 msec
Note: The length of low section will vary a little depending on the
conditions.
Fig. 2
Change in output voltage of R5549 on the LD-230 board
LD-230 BOARD (SIDE A)
VC-516 BOARD (SIDE A)
R5549
IC1301
IC5501
R5526
R5534
R5525
R5549: No Mount
(Short Land)
C5513
Fig. 1
Measurement points on the LD-230 board and the VC-516 board
1-3-1. E : 62 : 02 [Abnormality of IC for Steadyshot] Occurred
Order
Procedure
1
Turn the power OFF.
While measuring with an oscilloscope the output voltage of R5549 in the periphery of IC5501 on the LD-230 board, turn the
power ON to check that the output voltage immediately after the power on change as shown in Fig. 2.
2
3
If the output voltage change as shown in Fig. 2, replace the lens block (Note). If it does not change as shown in Fig. 2, inspect
the camera control circuit (IC1301 of VC-516 board) periphery.
Note: When the lens block was replaced, execute a necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
HDR-SR11/SR11E/SR12/SR12E_L2
1-3
ENGLISH
JAPANESE
1-3-2. E : 62 : 11 [Shift Lens Overheating (Pitch)] Occurred
Connect by the SeusEX and perform the following process.
Order Block Page Address Data
Procedure
1
2
3
4
5
6
7
8
11
11
11
11
11
11
11
11
80
8E
8E
8E
8E
8E
8E
80
7430
F946
F948
F948
F946
F948
F948
7430
01 Write the data. (After it starts, set it before caution is displayed.)
F0 Write the data.
01 Write the data. (Note 1)
00 Write the data.
10 Write the data.
01 Write the data. (Note 1)
00 Write the data.
00 Write the data.
Check if the shift lens moves while setting the order 2 to 7. If the shift lens does not move,
replace the lens block (Note 2). When the shift lens moved, proceed to the order 10.
9
While setting the order 2 to 7, measure with an oscilloscope the output voltage of R5526 in the
periphery of IC5501 on the LD-230 board to check the output voltage varies.
10
If the output voltage does not vary, replace the lens block (Note 2). When the output voltage
varied, proceed to the order 12.
11
12
Turn the power OFF.
While measuring with an oscilloscope the output voltage of R5549 in the periphery of IC5501
on the LD-230 board, turn the power ON to check that the output voltage immediately after the
power on change as shown in Fig. 2.
13
14
If the output voltage change as shown in Fig. 2, replace the lens block (Note 2). If it does not
change as shown in Fig. 2, inspect the camera control circuit (IC1301 of VC-516 board)
periphery.
Note 1: Finish this operation within 10 seconds. If it is likely to take more than 10 seconds, set block: 11, page: 8E, address:
F948, data: 00, and then retry.
Note 2: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
HDR-SR11/SR11E/SR12/SR12E_L2
1-4
ENGLISH
JAPANESE
1-3-3. E : 62 : 12 [Shift Lens Overheating (Yaw)] Occurred
Connect by the SeusEX and perform the following process.
Order Block Page Address Data
Procedure
1
2
3
4
5
6
7
8
11
11
11
11
11
11
11
11
80
8E
8E
8E
8E
8E
8E
80
7430
F947
F949
F949
F947
F949
F949
7430
01 Write the data. (After it starts, set it before caution is displayed.)
F0 Write the data.
01 Write the data. (Note 1)
00 Write the data.
10 Write the data.
01 Write the data. (Note 1)
00 Write the data.
00 Write the data.
Check if the shift lens moves while setting the order 2 to 7. If the shift lens does not move,
replace the lens block (Note 2). When the shift lens moved, proceed to the order 10.
9
While setting the order 2 to 7, measure with an oscilloscope the output voltage of R5534 in the
periphery of IC5501 on the LD-230 board to check the output voltage varies.
10
If the output voltage does not vary, replace the lens block (Note 2). When the output voltage
varied, proceed to the order 12.
11
12
Turn the power OFF.
While measuring with an oscilloscope the output voltage of R5549 in the periphery of IC5501
on the LD-230 board, turn the power ON to check that the output voltage immediately after the
power on change as shown in Fig. 2.
13
14
If the output voltage change as shown in Fig. 2, replace the lens block (Note 2). If it does not
change as shown in Fig. 2, inspect the camera control circuit (IC1301 of VC-516 board)
periphery.
Note 1: Finish this operation within 10 seconds. If it is likely to take more than 10 seconds, set block: 11, page: 8E, address:
F949, data: 00, and then retry.
Note 2: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
1-3-4. E : 62 : 20 [Abnormality of Thermistor] Occurred
Order
Procedure
1
Turn the power ON.
Confirm the connections of flexible flat cables and connectors between the lens block and LD-230 board, LD-230 board and
VC-516 board.
2
3
In case of no malfunction of connections, replace the lens block with new one. (Note) When the error has occurred in spite of the
lens replacement, replace LD-230 board with new one.
Note: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
HDR-SR11/SR11E/SR12/SR12E_L2
1-5
ENGLISH
JAPANESE
1-4. PRECAUTION ON REPLACING THE VC-516 BOARD
DESTINATION DATA
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Refer to Service Manual ADJ, and perform “DESTINATION DATA WRITE”.
USB SERIAL No.
The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Refer to Service Manual ADJ, and perform “USB SERIAL No. INPUT”.
HDR-SR11/SR11E/SR12/SR12E_L2
1-6
ENGLISH
JAPANESE
1. SERVICE NOTE
1-1. 修理時の電源供給について
本機では，安定化電源（8.4Vdc）からバッテリ端子に電源を供給した場合，約10秒後にシャットオフし，動作しなくなります。
これを避けるため，下記の方法を用いてください。
方法：
DC入力端子を使用する。（ACアダプタ（AC-L200/L200Bなど）を使用する。）
1-2. 自己診断機能
1-2-2.自己診断表示
1-2-1.自己診断機能について
本機の動作に不具合が生じたとき，ビューファインダまたは
LCD画面のカウンタ表示部分がアルファベットと数字の4桁
表示になり，3.2Hzで点滅します。この5文字の表示によっ
て対応者分類および不具合の生じたブロックの分類，不具合
の詳細コードを示します。
本機の動作に不具合が生じたとき，自己診断機能が働き，
ビューファインダまたはLCD画面に，どう処置したらよい
か判断できる表示を行います。「自己診断表示」と「サービス
モード表示」の２つの表示があります。自己診断機能につい
ては取扱説明書にも掲載されています。
ビューファインダまたはLCD画面
C : 3 1 : 1 1
3.2Hz点滅
1 1
C
3 1
詳細コード
対応者分類
ブロック分類
Cꢀ ：お客さま自身で対応
Hꢀ：販売店で対応
Eꢀ ：サービスエンジニアꢀ
で対応
対応方法の違いにより分類
例ꢀ 31･･･テープを入れ直す
「1-2-3.ꢀ自己診断コード表」
を参照
ꢀ
32･･･電源を入れ直す
HDR-SR11/SR11E/SR12/SR12E_L2
1-7
ENGLISH
JAPANESE
1-2-3. 自己診断コード表
自己診断コード
対
応
者
ブロック
機能
詳細
症状／状態
対応／方法
コード
C
C
0
1
4
3
0
0
0
1
標準以外のバッテリを使用している インフォリチウムバッテリを使用する。
フォーマットしていない“メモリー “メモリーステック デュオ”をフォーマットする。
ステック デュオ”を入れた
“メモリーステック デュオ”が壊 新しい“メモリーステック デュオ”に交換する。
れている
C
C
1
3
3
2
0
6
2
0
ディスクアクセスエラー
電源を外し，再度
入れ直
してから操作する。
フォーカスが合いにくい
操作スイッチの電源を入れ直
帰しない場合，レンズブロックのフォーカスMRセンサ
（LD-230基板CN5103 w;，waピン）を点検する。異常なけ
ればフォーカスモータ駆動回路（LD-230基板IC5201）を点
検する。
フラッシュメモリが書き換えられている フラッシュメモリのデータを元の値に戻す。（注意
ドライブ不良 ハードディスクドライブを点検または交換する。
ズーム動作の異常（ズームレンズの ズームレバーを操作したときにズーム動作をすれば，レン
す。
（フォーカスの初期化ができない）
復
E
E
E
2
3
6
0
1
1
0
0
1
0
0
0
1）
初期化ができない）
ズブロックのズームMRセンサ（LD-230基
板CN5103 qh，
qjピン）を点検する。ズーム動作をしなければズームモー
タ駆動回路（LD-230基
フォーカス，ズーム異 自己診断コードC：32：60とE：61：10の両方を点検す
る。
PITCH角速度
角速度 する。
手振れ補正が効きにくい（YAW 角 YAW角速度センサ（FR-278基板SE9002）周 辺回路を点検
速度センサ出力張り付き） する。
手振れ補正用ICの異 「1-3-1. E：62：0（2 手振れ補正用ICの異常）が出た場合」を参照。
手振れ補正用ICとマイクロコント 手振れ補正回路（LD-230基板IC5501）を点検。
ローラーとの通信
シフトレンズ初期化異 レンズブロックを交換する エラーが再度発生する場合
は， LD-230基板を交換する。（注意2）
板IC5201）を点検する。
E
E
E
6
6
6
1
2
2
1
0
0
1
0
1
常
手振れ補正が効きにくい（PITCH
センサ出力張り付き）
センサ（FR-278基板SE9001）周 辺回路を点検
E
E
6
6
2
2
0
0
2
3
常
異
常
E
E
E
6
6
6
2
2
2
1
1
1
0
1
2
常
。
シフトレンズオーバーヒート
(PITCH)
「1-3-2. E：62：1（1 シフトレンズオーバーヒート（PITCH））が出
た場合」を参照。
シフトレンズオーバーヒート
(YAW)
「1-3-3. E：6 2：12（シフトレンズオーバーヒート（YAW））が出
た場合」を参照。
E
E
E
6
9
9
2
1
4
2
0
0
0
1
0
サーミスタの異
フラッシュの充電異 フラッシュユニットの点検または交換をする。
フラッシュメモリの書込み/消去動 フラッシュメモリ（VC-516基板IC2101）を点検する。
作不良
注意1：ADJ編，「1-3. DESTINATION DATA WRITE」を参照してください。
常
「1-3-4. E：6 2：2 （0 サーミスタの異常）が出た場合」を参照。
常
注意2：レンズブロックを交換した場合は，ADJ編を参照して必要
な調整項目を実施すること。調整後は手振れ補正ONの状
態にして，手持ち動作で手振れ補正が適切に動作していることを確認する。
HDR-SR11/SR11E/SR12/SR12E_L2
1-8
ENGLISH
JAPANESE
1-3. シフトレンズエラーの対処方法
図2
約 330 msec
注意：Lowの区間の長さは場合によって多少異
なる
図2. LD-230基
板R5549の出力電圧の変化
図1
LD-230 BOARD (SIDE A)
VC-516 BOARD (SIDE A)
R5549
IC1301
IC5501
R5526
R5534
R5525
R5549: No Mount
(Short Land)
C5513
図1.LD-230基
板，VC-516基
板測
定箇
所
1-3-1. E：62：02（手振れ補正用ICの異
常）が出た場合
順
序
作業内容
1
電源を切る。
LD-230基板IC5501の周 辺にあるR5549の出力電圧をオシロスコープで測定しながら電源を入れる。電源投入直
出力電圧が図2の様に変化することを確認する。
出力電圧が図2の様に変化するときはレンズブロックを交換する（注意
トロール回路（VC-516基板IC1301）周 辺を点検する。
後の
2
3
）。図2の様に変化しないときはカメラコン
注意：レンズブロックを交換した場合は，A D J 編を参照して必要
な調整項目を実施すること。調整後は手振れ補正O N の状
態にして，手持ち動作で手振れ補正が適切に動作していることを確認する。
HDR-SR11/SR11E/SR12/SR12E_L2
1-9
ENGLISH
JAPANESE
1-3-2. E：62：11（シフトレンズオーバーヒート（PITCH））が出た場合
SeusEXで接続し、次の手順 を行う。
順
序 ブロック ページ アドレス データ
作業内容
1
2
3
4
5
6
7
8
11
11
11
11
11
11
11
11
80
8E
8E
8E
8E
8E
8E
80
7430
F946
F948
F948
F946
F948
F948
7430
01
F0
01
00
10
01
00
00
データを書き込む。（セット起動後，コーションが表示される前に設定する事。）
データを書き込む。
データを書き込む。（注意1）
データを書き込む。
データを書き込む。
データを書き込む。（注意1）
データを書き込む。
データを書き込む。
順序2〜7を設定している間にシフトレンズが動いたか確認する。もしシフト
レンズが動かない場合はレンズブロックを交換する（注意2）。動く場合は順序
10に進む。
9
LD-230基
板IC5501の周 辺にあるR5526の出力電圧をオシロスコープで測定しな
10
がら，順 序2～7を設定したときに出力電圧が変化することを確認する。
出力電圧が変化しないときはレンズブロックを交換する（注意2）。変化するときは
11
12
順
序12に進む。
電源を切る。
LD-230基板IC5501の周 辺にあるR5549の出力電圧をオシロスコープで測定しな
がら電源を入れる。電源投入直後の出力電圧が図2の様に変化することを確認
13
14
する。
出力電圧が図2の様に変化するときはレンズブロックを交換する（注意2）。図2の
様に変化しないときはカメラコントロール回路（VC-516基
板IC1301）周 辺を点検
する。
注意1：この操作は10秒以内に終了してください。もし10秒以上経過しそうな場合は，ブロック：11，ページ：8E，アドレ
ス：F948，データ：00 に設定しなおしてから再度実行してください。
注意2：レンズブロックを交換した場合は，ADJ編を参照して必要
な調整項目を実施すること。調整後は手振れ補正ONの状
態にして，手持ち動作で手振れ補正が適切に動作していることを確認する。
HDR-SR11/SR11E/SR12/SR12E_L2
1-10
ENGLISH
JAPANESE
1-3-3. E：62：12（シフトレンズオーバーヒート（YAW））が出た場合
SeusEXで接続し、次の手順 を行う。
順
序 ブロック ページ アドレス データ
作業内容
1
2
3
4
5
6
7
8
11
11
11
11
11
11
11
11
80
8E
8E
8E
8E
8E
8E
80
7430
F947
F949
F949
F947
F949
F949
7430
01
F0
01
00
10
01
00
00
データを書き込む。（セット起動後，コーションが表示される前に設定する事。）
データを書き込む。
データを書き込む。（注意1）
データを書き込む。
データを書き込む。
データを書き込む。（注意1）
データを書き込む。
データを書き込む。
順序2〜7を設定している間にシフトレンズが動いたか確認する。もしシフトレ
ンズが動かない場合はレンズブロックを交換する（注意2）。動く場合は順序10
に進む。
9
LD-230基
板IC5501の周 辺にあるR5534の出力電圧をオシロスコープで測定しな
10
がら，順 序2～7を設定したときに出力電圧が変化することを確認する。
出力電圧が変化しないときはレンズブロックを交換する（注意2）。変化するときは
11
12
順
序12に進む。
電源を切る。
LD-230基板IC5501の周 辺にあるR5549の出力電圧をオシロスコープで測定しな
がら電源を入れる。電源投入直後の出力電圧が図2の様に変化することを確認す
13
る。
出力電圧が図2の様に変化するときはレンズブロックを交換する（注意2）。図2の
様に変化しないときはカメラコントロール回路（VC-516基
板IC1301）周 辺を点検
する。
注意1：この操作は10秒以内に終了してください。もし10秒以上経過しそうな場合は，ブロック：11，ページ：8E，アドレ
ス：F949，データ：00 に設定しなおしてから再度実行してください。
注意2：レンズブロックを交換した場合は，ADJ編を参照して必要
な調整項目を実施すること。調整後は手振れ補正ONの状
態にして，手持ち動作で手振れ補正が適切に動作していることを確認する。
1-3-4. E：62：20（サーミスタの異
常）が出た場合
順
序
作業内容
1
電源を入れる。
続を確認する。
レンズブロックとLD-230基板間，LD-230基板とVC-516基板間の各フレキシブルフラットケーブルとコネクタの接
2
3
接続に異常がなければレンズブロックを交換する。（注意） 交換してもエラーが発生する場合はLD-230基板を交
換する。
注意：レンズブロックを交換した場合は，A D J 編を参照して必要
な調整項目を実施すること。調整後は手振れ補正O N の状
態にして，手持ち動作で手振れ補正が適切に動作していることを確認する。
HDR-SR11/SR11E/SR12/SR12E_L2
1-11
ENGLISH
JAPANESE
1-4. VC-516基板交換時の注意
仕向けデータ
補修用基板と交換する時，補修用基板に書かれている仕向けデータは元の設定と違っている場合があります。
ADJ編を参照して，「DESTINATIONꢀDATAꢀWRITE」を行ってください。
USBシリアルNo.
セットは，1台毎に異なる固有のID（USBꢀSerialꢀNo.）を書き込んだ後，出荷されています。
新品の補修用基板には，このIDが書き込まれていないので，基板交換後にIDを入力する必要があります。
ADJ編を参照して，「USBꢀSERIALꢀNo.ꢀINPUT」を行ってください。
HDR-SR11/SR11E/SR12/SR12E_L2
1-12
HDR-SR11
(JAPANESE Model)
(ENGLISH)
*
Manufacturing year
1-6. PRECAUTION ON REPLACING
THE CABINET (G(900)) ASSY
(HDR-SR11)
The model display adopts the laser printing method.Therefore, the
cabinet (G(900)) assy for replacement differs depending on the
destination.
Serial No.
Description
*
Affix the label
Part No.
As similar displays are provided, choose the suitable one for order.
A-1526-522-A
CABINET(G(900))(SR11J1)
Note1: After replacing the cabinet (G(900)) assy, the serial number
for it will be changed to the one exclusive for service use.
Inform a customer of the serial number change and change the serial
number in the repair data.
HDR-SR11
(Tourist Model)
Note 2: When replacing the cabinet (G(900)) assy for US, affix the
“Manufacturing year” label and the “Factory” label on the specified
location as shown in the figure.
The replacement caution label and inset (how to affix) are supplied
together with the cabinet (G(900)) assy.
Serial No.
Description
CABINET(G(900))(SR11JE3)
Part No.
A-1526-524-A
HDR-SR11
(US Model)
Serial No.
Note 3: When replacing the cabinet (G(900)) assy for Korea, affix
the “Manufacturing year” label on the specified location as shown
in the figure.
The replacement caution label and inset (how to affix) are supplied
together with the cabinet (G(900)) assy.
*
Affix the label
*
Factory
*
Manufacturing year
Description
Part No.
A-1526-525-A
CABINET(G(900))(SR11U2)
(JAPANESE)
1-6. キャビネット(G(900))組立交換時の注意
(HDR-SR11)
HDR-SR11
(Canadian Model)
機種の表示部はレーザー印字方式を採用しております。
この為，交換用のキャビネット(G(900))組立は仕向けによ
り異なります。類似の表示もありますので，該当するもの
を選んで注文して下さい。
Serial No.
Part No.
A-1526-526-A
Description
CABINET(G(900))(SR11CA2)
注意1: キャビネット(G(900))組立交換後はシリアルナン
バーがサービス専用のシリアルナンバーに変更されます。
お客様への案内と修理データのシリアルナンバー変更を
行ってください。
HDR-SR11
(E Model)
注意2: US仕向けキャビネット(G(900))組立を交換した際
は「製造年月」を表すラベルと，「製造所」を表すラベル
を図の指定位置に貼り付けてください。
Serial No.
Part No.
A-1526-527-A
Description
CABINET(G(900))(SR11E23)
なお，キャビネット(G(900))組立には時期表示ラベル，投
げ込み(ラベル貼り方)がセットで供給されます。
HDR-SR11
(Korea Model)
*
Affix the label
注意3: Korean仕向けキャビネット(G(900))組立を交換し
た際は，「製造年月」を表すラベルを図の指定位置に貼り
付けてください。
なお，キャビネット(G(900))組立には時期表示ラベル，投
げ込み(ラベル貼り方)がセットで供給されます。
*
Manufacturing year
Serial No.
Part No.
Description
A-1526-528-A
CABINET(G(900))(SR11KR2)
HDR-SR11/SR11E/SR12/SR12E_L2
1-13
HDR-SR11E
(E, Hong Kong, Australian Models)
(ENGLISH)
1-7. PRECAUTION ON REPLACING
THE CABINET (G(900)) ASSY
(HDR-SR11E)
Serial No.
The model display adopts the laser printing method.Therefore, the
cabinet (G(900)) assy for replacement differs depending on the
destination.
Part No.
A-1526-529-A
Description
CABINET(G(900))(SR11EE34)
As similar displays are provided, choose the suitable one for order.
HDR-SR11E
(NE Models)
Note1: After replacing the cabinet (G(900)) assy, the serial number
for it will be changed to the one exclusive for service use.
Inform a customer of the serial number change and change the serial
number in the repair data.
Serial No.
Description
CABINET(G(900))(SR11ECEL)
(JAPANESE)
1-7. キャビネット(G(900))組立交換時の注意
(HDR-SR11E)
Part No.
A-1526-530-A
HDR-SR11E
(Tourist Model)
機種の表示部はレーザー印字方式を採用しております。
この為，交換用のキャビネット(G(900))組立は仕向けによ
り異なります。類似の表示もありますので，該当するもの
を選んで注文して下さい。
Serial No.
Description
CABINET(G(900))(SR11EJE3)
Part No.
A-1526-560-A
注意1: キャビネット(G(900))組立交換後はシリアルナン
バーがサービス専用のシリアルナンバーに変更されます。
お客様への案内と修理データのシリアルナンバー変更を
行ってください。
HDR-SR11E
(AEP, UK Model)
Serial No.
Description
Part No.
A-1526-561-A
CABINET(G(900))(SR11ECEH)
HDR-SR11E
(Chinese Model)
Serial No.
Part No.
Description
A-1526-562-A
CABINET(G(900))(SR11ECN2)
HDR-SR11/SR11E/SR12/SR12E_L2
1-14
HDR-SR12
(Japanese Model)
(ENGLISH)
* Manufacturing year
1-8. PRECAUTION ON REPLACING
THE CABINET (G(900)) ASSY
(HDR-SR12)
The model display adopts the laser printing method.Therefore, the
cabinet (G(900)) assy for replacement differs depending on the
destination.
Serial No.
Description
CABINET(G(900))(SR12J1)
*
Affix the label
Part No.
A-1526-563-A
As similar displays are provided, choose the suitable one for order.
HDR-SR12
(Tourist Model)
Note1: After replacing the cabinet (G(900)) assy, the serial number
for it will be changed to the one exclusive for service use.
Inform a customer of the serial number change and change the serial
number in the repair data.
Note 2: When replacing the cabinet (G(900)) assy for US, affix the
“Manufacturing year” label and the “Factory” label on the specified
location as shown in the figure.
The replacement caution label and inset (how to affix) are supplied
together with the cabinet (G(900)) assy.
Serial No.
Part No.
A-1526-565-A
Description
CABINET(G(900))(SR12JE3)
HDR-SR12
(US Model)
Serial No.
Note 3: When replacing the cabinet (G(900)) assy for Korea, affix
the “Manufacturing year” label on the specified location as shown
in the figure.
The replacement caution label and inset (how to affix) are supplied
together with the cabinet (G(900)) assy.
* Factory * Manufacturing year
*
Affix the label
Part No.
Description
A-1526-566-A
CABINET(G(900))(SR12U2)
(JAPANESE)
1-8. キャビネット(G(900))組立交換時の注意
(HDR-SR12)
HDR-SR12
(Canadian Model)
機種の表示部はレーザー印字方式を採用しております。
この為，交換用のキャビネット(G(900))組立は仕向けによ
り異なります。類似の表示もありますので，該当するもの
を選んで注文して下さい。
Serial No.
Part No.
Description
A-1526-567-A
CABINET(G(900))(SR12CA2)
注意1: キャビネット(G(900))組立交換後はシリアルナン
バーがサービス専用のシリアルナンバーに変更されます。
お客様への案内と修理データのシリアルナンバー変更を
行ってください。
HDR-SR12
(E Model)
Serial No.
注意2: US仕向けキャビネット(G(900))組立を交換した際
は「製造年月」を表すラベルと，「製造所」を表すラベル
を図の指定位置に貼り付けてください。
Part No.
A-1526-568-A
Description
CABINET(G(900))(SR12E23)
HDR-SR12
(Korean Model)
なお，キャビネット(G(900))組立には時期表示ラベル，投
げ込み(ラベル貼り方)がセットで供給されます。
*
Affix the label
注意3: Korean仕向けキャビネット(G(900))組立を交換し
た際は，「製造年月」を表すラベルを図の指定位置に貼り
付けてください。
Serial No.
* Manufacturing year
なお，キャビネット(G(900))組立には時期表示ラベル，投
げ込み(ラベル貼り方)がセットで供給されます。
Part No.
A-1526-575-A
Description
CABINET(G(900))(SR12KR2)
HDR-SR11/SR11E/SR12/SR12E_L2
1-15
HDR-SR12E
(E, Hong Kong, Australian Models)
(ENGLISH)
1-9. PRECAUTION ON REPLACING
THE CABINET (G(900)) ASSY
(HDR-SR12E)
Serial No.
The model display adopts the laser printing method.Therefore, the
cabinet (G(900)) assy for replacement differs depending on the
destination.
Part No.
A-1526-576-A
Description
CABINET(G(900))(SR12EE34)
As similar displays are provided, choose the suitable one for order.
HDR-SR12E
(NE Models)
Note1: After replacing the cabinet (G(900)) assy, the serial number
for it will be changed to the one exclusive for service use.
Inform a customer of the serial number change and change the serial
number in the repair data.
Serial No.
Part No.
A-1526-577-A
Description
CABINET(G(900))(SR12ECEL)
(JAPANESE)
1-9. キャビネット(G(900))組立交換時の注意
(HDR-SR12E)
HDR-SR12E
(Tourist Model)
機種の表示部はレーザー印字方式を採用しております。
この為，交換用のキャビネット(G(900))組立は仕向けによ
り異なります。類似の表示もありますので，該当するもの
を選んで注文して下さい。
Serial No.
Part No.
Description
A-1526-578-A
CABINET(G(900))(SR12EJE3)
注意1: キャビネット(G(900))組立交換後はシリアルナン
バーがサービス専用のシリアルナンバーに変更されます。
お客様への案内と修理データのシリアルナンバー変更を
行ってください。
HDR-SR12E
(AEP, UK Model)
Serial No.
Part No.
Description
A-1526-579-A
CABINET(G(900))(SR12ECEH)
HDR-SR12E
(Chinese Model)
Serial No.
Part No.
Description
A-1526-580-A
CABINET(G(900))(SR12ECN2)
HDR-SR11/SR11E/SR12/SR12E_L2
1-16E
2. DISASSEMBLY
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
• When remove a connector, don’t pull at wire of connector. It is possible that a wire is snapped.
pieces of gilt may be left inside)
• When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
DISCHARGING OF THE ST-185 BOARD’S CHARGING CAPACITOR (C5006)
The charging capacitor (C5006) of the ST-185 board is charged
up to the maximum 330 V potential.
Note: High-voltage cautions
There is a danger of electric shock by this high voltage when the
Discharging the Capacitor
capacitor is handled by hand. The electric shock is caused by
Short-circuit between the two points
the charged voltage which is kept without discharging when the
main power of the unit is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
with the short jig about 10 seconds.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 kΩ /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
ST-185 Board
1 kΩ/1 W
R:1 kΩ/1 W
(Part code: 1-215-869-11)
Wrap insulating tape.
C5006
NOTE FOR DISCONNECTING THE HARNESS (COAXIAL CABLE)
When disconnecting the harness (COAXIAL CABLE), do not
pull the harness part but pull off the connector body with tweezers
etc.
Harness
(coaxial cable)
Tweezers etc.
HDR-SR11/SR11E/SR12/SR12E_L2
2-1
2-1. IDENTIFYING PARTS
EVF Block
⋅
BL-017 Board
Cabinet (L) Section
BT Panel Block
⋅
⋅
⋅
VC-516 Board
JK-356 Board
FR-278 Board
⋅
MS-381 Board
Cabinet (Top) Block
Bottom Cabinet Block
Cabinet (F) Section
⋅
CR-089 Board
Cabinet (R) Section
⋅
ST-185 Board
⋅
⋅
CK-185 Board
PD-343 Board
⋅
LD-230 Board
- DISASSEMBLY FLOW -
2-2-1. OVERALL SECTION-1
- Cabinet (G) Assy
- HDD
- Bottom Cabinet Block
2-2-2. OVERALL SECTION-2
- Cabinet (R) Section
- Cabinet (Top) Block
- EVF Block
2-2-8. CABINET (R) SECTION
- Loud Speaker
2-2-3. OVERALL SECTION-3
- BT Panel Block
- CK-185 Board
- Cabinet (F) Section
- Panel Block
2-2-4. CABINET (L) SECTION-1
- VC-516 Board
2-2-6. CABINET (F) SECTION
- Lens Block
2-2-9. PANEL BLOCK
- Hinge Assy
- Control Switch Block (RS28900)
- Lens Barrier Unit
- PD-343 Board
- LCD
2-2-5. CABINET (L) SECTION-2
- JK-356 Board
- Control Switch Block (PS28100)
- FR-278 Board
2-2-7. LENS BLOCK
- ST-185 Board
- LD-230 Board
- Flash Unit
HDR-SR11/SR11E/SR12/SR12E_L2
2-2
HELP
2-2. DISASSEMBLY
EXPLODED VIEW
HARDWARE LIST
2-2-1. OVERALL SECTION-1
Follow the disassembly in the numerical order given.
1 Cabinet (G) Assy (1-1 to 1-6)
2 HDD (2-1 to 2-3)
3 Bottom Cabinet Block (3-1 to 3-2)
1-2
(Slide the
LF Jack Cover)
1 Cabinet (G)
1-4
(Slide the
Jack Cover(G))
Assy
1-5
(#2)
1-3
(#2)
2-1
2 HDD
Overall
1-6
(Claw)
Section-2
(See Page 2-4)
1-1
(#2)
2-3
2-2
3-2
3-1 (#2)
3 Bottom Cabinet Block
HDR-SR11/SR11E/SR12/SR12E_L2
2-3
2-2-2. OVERALL SECTION-2
Follow the disassembly in the numerical order given.
1 Cabinet (R) Section (1-1 to 1-8)
2 Cabinet (Top) Block (2-1 to 2-5)
3 EVF Block (3-1 to 3-3)
EXPLODED VIEW
HARDWARE LIST
2 Cabinet (Top)
Block
2-4
(Open the
LCD Panel)
3-1
(#2)
A
HELP01
3-3
3 EVF Block
2-5
2-2
(Claw)
(#2)
1 Cabinet (R)
Section
(See Page 2-10)
1-7(#12)
3-2
(#2)
2-3
(#12)
2-1
(#2)
A
1-6
(#2)
Overall
Section-3
1-8
(See Page 2-5)
1-2
(#2)
1-3
(Claw)
1-4
1-5
(#2)
1-1
(Open the
LCD Panel)
HDR-SR11/SR11E/SR12/SR12E_L2
2-4
2-2-3. OVERALL SECTION-3
Follow the disassembly in the numerical order given.
1 BT Panel Block (1-1 to 1-4)
EXPLODED VIEW
HARDWARE LIST
2 Cabinet (F) Section (2-1 to 2-9)
2-2
2-3
2-1
(#3)
A
1-1
(#2)
2 Cabinet (F)
Section
(See Page 2-8)
2-7
1-3
(#3)
2-6
A
2-8
(#2)
1-4
1 BT Panel Block
2-4
1-2
HELP02
HELP03
2-9
Note: High-voltage cautions
Discharging the Capacitor
2-5
Refer to page 2-1 “Note
for disconnecting the
Short-circuit between the two points with the short jig
about 10 seconds. To avoid the spark with the metal
plate, wrap the short jig with the insulation tape.
harness (caoxial cable)”.
C5006
(Charging
Capacitor)
ST-185
Board
R:1 kΩ/1 W
(Part code: 1-215-869-11)
HDR-SR11/SR11E/SR12/SR12E_L2
2-5
2-2-4. CABINET (L) SECTION-1
Follow the disassembly in the numerical order given.
1 VC-516 Board (1-1 to 1-8)
EXPLODED VIEW
HARDWARE LIST
1-2
1-1
1-8
HELP05
1-3
1-7
1-6
HELP04
1-4 (#3)
1-5
(#3)
1 VC-516 Board
HDR-SR11/SR11E/SR12/SR12E_L2
2-6
2-2-5. CABINET (L) SECTION-2
Follow the disassembly in the numerical order given.
1 JK-356 Board (1-1 to 1-6)
EXPLODED VIEW
HARDWARE LIST
2 Control Switch Block (PS28100) (2-1)
3 FR-278 Board (3-1 to 3-4)
2 Control Switch Block
(PS28100)
3-2
2-1
(#11)
1-5
1-3(#11)
1-2
1-4
(#3)
1-1(#11)
1-6
1 JK-356 Board
3-3
3-1
(#11)
3-4
(#3)
3 FR-278 Board
HDR-SR11/SR11E/SR12/SR12E_L2
2-7
2-2-6. CABINET (F) SECTION
Follow the disassembly in the numerical order given.
1 Lens Block (1-1 to 1-4)
EXPLODED VIEW
HARDWARE LIST
2 Control Switch Block (RS28900) (2-1)
3 Lens Barrier Unit (3-1 to 3-3)
HELP09
1 Lens Block
(See Page 2-9)
3-3
(#11)
3-1
(#3)
3-2
HELP07
1-4
(#11)
1-2
HELP06
1-1
HELP08
HELP06
1-3
2-1
(#11)
3 Lens Barrier Unit
2 Control Switch Block
(RS28900)
HDR-SR11/SR11E/SR12/SR12E_L2
2-8
2-2-7. LENS BLOCK
EXPLODED VIEW
HARDWARE LIST
Follow the disassembly in the numerical order given.
1 ST-185 Board (1-1 to 1-4)
2 LD-230 Board (2-1 to 2-3)
3 Flash Unit (3-1 to 3-6)
1 ST-185 Board
1-2
(#3)
3-1 (#3)
3-6
(Peel off the
Flexible Board)
1-1
HELP10
1-3 (Claw)
3-3 (Dowels)
3-4 (#11)
HELP13
1-4
3-2
(#3)
3-5
3 Flash Unit
LD-230
2 LD-230 Board
2-2
(#3)
2-1
2-3
HELP11
HELP12
Refer to page 2-1 "Note
for disconnecting the
Lens Block
harness (coaxial cable) "
HDR-SR11/SR11E/SR12/SR12E_L2
2-9
2-2-8. CABINET (R) SECTION
Follow the disassembly in the numerical order given.
1 Loud Speaker (1-1 to 1-3)
EXPLODED VIEW
HARDWARE LIST
2 CK-185 Board (2-1 to 2-3)
3 Panel Block (3-1 to 3-2)
1-3
1-2 (#11)
1 Loud Speaker
HELP14
1-1
3-2
2-2
(#11)
3 Panel Block
(See Page 2-11)
2-3
2 CK-185
Board
HELP14
2-1
3-1
(#2)
HDR-SR11/SR11E/SR12/SR12E_L2
2-10
2-2-9. PANEL BLOCK
EXPLODED VIEW
HARDWARE LIST
Follow the disassembly in the numerical order given.
1 Hinge Assy (1-1 to 1-12)
2 PD-343 Board (2-1 to 2-9)
3 LCD (3-1)
1 Hinge Assy 1-10
B
1-7
(#2)
HELP16
1-12
3 LCD
1-8
(Claw)
3-1
(Claw)
1-11
1-5
D
2-9
2-1
1-6
HELP16
2-5 (#11)
2-8
1-9
2-3
2-2
HELP15
D
PD-343
A
A
C
1-1
2-6
(#11)
(#2)
B
1-4
1-3
(Claw)
2 PD-343
1-2
(Claw)
Board
2-4
C
2-7
HDR-SR11/SR11E/SR12/SR12E_L2
2-11E
HELP
Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
HELP01
EVF Block
FP-811 Flexible Board
EVF Block
FP-811 Flexible Board
HDR-SR11/SR11E/SR12/SR12E_L2
HELP
HELP02
DC Jack Harnesses
(to the DC IN Jack)
DC Jack Harnesses
(to the Battery Terminal Board)
Secure the space by arranging DC Jack Harness
as shown in the figure.
BT Harness Retainer
Insert the lib portion to
Main Frame.
BT Panel
(900) Assy
Claw
BT Harness Retainer
Open slightly
the BT Panel Block
Main Frame
DC Jack Harnesses
DC Jack Harnesses
HDR-SR11/SR11E/SR12/SR12E_L2
HELP
HELP03
Claws
FP-803 Flexible Board
HELP04
FP-799 Flexible Board
FP-798 Complete
Flexible Board
Pass the FP-799 Flexible Board through under
the screwing in position of the Main Frame.
Main Frame.
FP-812 Flexible Board
Two CutOuts
Two Libs
HDR-SR11/SR11E/SR12/SR12E_L2
HELP
HELP05
VC-516 Board
Shield Sheet (AN)
Be careful not to overlap it into
the pattern prohibition area.
Be careful not to bring it out of IC.
HDR-SR11/SR11E/SR12/SR12E_L2
HELP
HELP06
+1
0
0 mm
Flexible Board
(Lens Barrier Unit)
1+1
mm
0
Tape (A)
Insert the Flexible Board
in to the Claw.
Tape (A)
1+1
mm
0
Insert the Flexible Board
in to the Claw and the Board.
HDR-SR11/SR11E/SR12/SR12E_L2
HELP
HELP07
Tape (A)
Tape (A)
Lens Barrier Unit
Lens Barrier Unit
HELP08
Lib
Flexible Board
(Control Switxh Block RS28900)
HDR-SR11/SR11E/SR12/SR12E_L2
HELP
HELP09
Printed end
Valley fold
1mm
Be careful not to overlap the bended
the flexible board to the Microphone unit.
Microphone Unit
NON WOVEN (T0.25)
(16mm × 7mm)
Microphone Holder
Assy (900)
Mountain fold
Microphone
Frame (900)
Microphone Unit
Push the Flexible Board
Claws
HELP10
Flexible Board
(Flash Unit)
LD-230 Board
HDR-SR11/SR11E/SR12/SR12E_L2
HELP
HELP11
Valley fold
Mountain fold
To the LD-230 Board
Valley fold
Reinforcement
FP-801 Felxuble Board
To the VC-516 Board
HELP12
Push the Flexible Board
direction of the arrow.
Claw
Flexible Board
(Lens Unit)
HDR-SR11/SR11E/SR12/SR12E_L2
HELP
HELP13
Lens Frame
(R(900))
CMOS Block Assy
(CM-094 Board)
CM Radiation Sheet (900)
Be sure not to load to CM-094 Board
and not to bend the sheet.
HELP14
Dowel
Lib
Harness
(Red)
Harness
(Black)
Engage the NS knob with
the Slide witch.
NS Nkob
Slide Switch
CK-185 Board
Lib
Harnesses
(Loud Speaker(1.6cm))
HDR-SR11/SR11E/SR12/SR12E_L2
HELP
HELP15
Leave wrinkles to the Flexible Board.
Flexible Board
(TP Block Assy)
HDR-SR11/SR11E/SR12/SR12E_L2
HELP
HELP16
THE METHOD OF ATTACHMENT OF FP-807 FLEXIBLE BOARD AND FP-454 FLEXIBLE BOARD
3 Install the flexible clamp in the hinge assy.
1 Fold dotted line parts of the FP-807 flexible board
as shown in figure.
Mountain fold
Flexible clamp
Hinge assy
Mountain fold
Valley fold
Adhesive tape
Adhesive tape
Valley fold
4 Roll the the FP-807 flexible board 1.5 times,
in the direction of arrow A.
A
Overlap the corners.
5 Put the adhesive part and FP-807 flexible
board on the hinge assy according to the
position of the boss.
2 Pass the FP-807 flexible board through
the flexible clamp
.
Flexible clamp
Boss
Adhesive part
HDR-SR11/SR11E/SR12/SR12E_L2
HELP
6 Insert the FP-454 flexible board to the flexible clamp as shown in figure.
FP-454 flexible board
Flexible clamp
HDR-SR11/SR11E/SR12/SR12E_L2
HELP
3. BLOCK DIAGRAMS
Link
OVERALL BLOCK DIAGRAM (1/6)
OVERALL BLOCK DIAGRAM (6/6)
POWER BLOCK DIAGRAM (1/3)
POWER BLOCK DIAGRAM (2/3)
POWER BLOCK DIAGRAM (3/3)
OVERALL BLOCK DIAGRAM (2/6)
OVERALL BLOCK DIAGRAM (3/6)
OVERALL BLOCK DIAGRAM (4/6)
OVERALL BLOCK DIAGRAM (5/6)
HDR-SR11/SR11E/SR12/SR12E_L2
3. BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM (1/6) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
CM-094 BOARD
VC-516 BOARD (1/5)
CN6801
10M_DOAP, 10M_DOAM, 10M_DOBP,
10M_DOBM, 10M_DOCP, 10M_DOCM,
10M_DODP, 10M_DODM, 10M_DOEP,
10M_DOEM, 10M_DOFP, 10M_DOFM,
10M_DOGP, 10M_DOGM, 10M_DOHP,
10M_DOHM
CN1301
EMC_XDQM[0] - EMC_XDQM[3]
EMC_DATA [0] - EMC_DATA [31]
EMC_XDQM[0] - EMC_XDQM[3]
EMC_DATA [0] - EMC_DATA [31]
VIN_C0 - VIN_C7
VIN_Y0 - VIN_Y7
LENS BLOCK (1/2)
SENS_DATA_P_0 - SENS_DATA_P_7,
SENS_DATA_M_0 - SENS_DATA_M_7
IRIS
(SHUTTER)
IC6804
CMOS IMAGER
SENSSCK, SENS_VD, SENS_HD,
IC_1301_SDO, SENSXCS
VIN_HD, VIN_VD, VIN_FLD,
EXT_CAM_CLK
SCK, XVS, XHS, IC_1301_SDO, XCE
EMC_ADDR [0] - EMC_ADDR [12],
EMC_ADDR [14], EMC_ADDR [15]
IC2101
(1/2)
EMC_ADDR [0] - EMC_ADDR [15]
(TO LENS BLOCK 2/2)
512M
SDRAM
(9/22)
DCKP, DCKM
INCK
SENS_CLK_P, SENS_CLK_M
EMC_CKE
EMC_XCAS
EMC_XCS [1]
EMC_CLK0_OUT
EMC_CLK0_IN
EMC_XWE
EMC_CKE
EMC_XCAS
EMC_XCS [1]
EMC_CLK0_OUT
AJ15
AE16
AF10
W25
W26
AF17
AG16
F3
J11
J13
K11
SYSTEM_CLOCK
XFLASH_RST
4
2
N11
N4
1
8
40
33
P1
X1301
48MHz
IC1303
XCLR
IC1701
(1/4)
BUFFER
(3/22)
EMC_XWE
EMC_XRAS
A_1.8V
J10
J12
EMC_XRAS
CPU
XIC_1301_COM_REQ
(6/22, 7/22, 8/22)
U7
N4
M2
P5
AE1
H24
AN20
AP18
AM21
B23
PCI_XREQFS1_AR
PCI_XGNTTS1_AR
PCI_XINTB_AR
XRESET_REQ
EMC_DATA [0] - EMC_DATA [15]
EMC_ADDR [0] - EMC_ADDR [15]
IC2101
(2/2)
SYS_V
SSS
XWEN
EXT_CAM_VD
D25
C28
D29
B20
512M
OneNAND
FLASH
(9/22)
1
OVERALL (5/6)
(PAGE 3-5)
IC1301
(1/3)
EMC_XWE
EMC_XRAS
EMC_XOE
P7
T5
N10
R6
P11
U3
T4
E8
CPU
(SIGNAL
PROCESS)
(3/22, 4/22)
EMC_XOE
EMC_RDY0
EMC_XRESET_OUT
EMC_XCS [0]
EMC_CLK1_OUT
EMC_CLK1_IN
AG15
AG17
AF16
EMC_RDY0
EMC_XRESET_OUT
EMC_XCS [0]
EMC_CLK1_OUT
XFLASH_RST
AG10
Y25
Y26
XFLASH_RST
(PAGE 3-3)
IC_1301_DDR2_DATA_0 - IC_1301_DDR2_DATA_31
IC_1301_DDR2_ADDR_0 - IC_1301_DDR2_ADDR_13
IC1601
IC_1301_DDR2_XCS_0, IC_1301_DDR2_XWE,
IC_1301_DDR2_XRAS, IC_1301_DDR2_XCAS,
IC_1301_DDR2_CKE1, IC_1301_DDR2_BA_1,
IC_1301_DDR2_BA_0, IC_1301_DDR2_CLK,
IC_1301_DDR2_DCLKN
MOBILE DDR
SDRAM
(5/22)
IC_1301_DDR2_DQS_0 - IC_1301_DDR2_DQS_3,
IC_1301_DDR2_DQM_0 - IC_1301_DDR2_DQM_3
: VIDEO SIGNAL
HDR-SR11/SR11E/SR12/SR12E_L2
3-1
3-2. OVERALL BLOCK DIAGRAM (2/6) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
VC-516 BOARD (2/5)
FP-811
FLEXIBLE BOARD
BL-017
BOARD
IC_2401_C/PB_OUT
AA11
CN3101
EVF_HST
CN5701
CN5702
DR_VDATA0 - DR_VDATA7
IC_2401_Y_OUT
AA9
Y10
EVF_HST
H2
G1
F1
G11
K3
K1
J2
L3
H1
L8
L6
L7
L10
K11
17
16
15
13
12
11
10
9
17
16
15
13
12
11
10
9
8
7
6
5
5
6
7
IC3101
EVF DRIVER
(17/22)
EVF_HCK2
EVF_HCK1
EVF_REF
EVF_VST
EVF_EN
EVF_STB
EVF_VCK
EVF_PCG
EVF_VB
EVF_HCK2
EVF_HCK1
EVF_REF
EVF_VST
EVF_EN
EVF_STB
EVF_VCK
EVF_PCG
EVF_VB
EVF_VR
EVF_VG
EVF_PSIG
EVF_COM
IC_2401_PR_OUT
DR_GHDATA0 - DR_GHDATA3
DR_GHPILOT
EVF_R
EVF_G
EVF_B
EVF_R
EVF_G
EVF_B
Y7
Y6
AA7
D11
E11
F11
11
13
15
12
14
16
17
18
19
20
21
H35
B15
LCD902
COLOR
EVF
IC2401
(1/2)
DR_GSDATA0 - DR_GSDATA3
EVF_HD
EVF_VD
EVF_HD
EVF_VD
K4
J2
A2
B1
SOC
(12/22)
DR_GSPILOT
DR_VINCK
XCS_IC_2401
DR_SCK54
XBB_RST
G35
F35
U27
E35
G20
D12
E21
H2
F20
J21
UNIT
8
7
6
5
4
3
IC3301
XBB_SCK
BB_SO
BB_SI
27bit DISPLAY SERIAL
INTERFACE TRANSMITTER
(19/22)
A4
B4
A5
EVF_VR
EVF_VG
EVF_PSIG
EVF_COM
XBB_RST
4
3
XCS_EVF
EVF_BL_ON
R27
D26
XBB_RST
XCS_EVF
C1
B5
Q3101
EVF BL SWITCH
DPNR0 - DPNR7
DPNG0 - DPNG7
IC1701
(2/4)
D5701
(EVF BACKLIGHT)
LED_K
G10
1
1
CPU
(6/22, 7/22, 8/22)
EVF_BL_ON
CN3301
BB_SI
4
OVERALL (4/6)
(PAGE 3-4)
D0+_TSY - D2+_TSY, D0-_TSY - D2-_TSY, CLK+_TSY, CLK-_TSY
DPNB0 - DPNB7
XBB_SCK
BB_SO
BB_SI
XBB_SCK
BB_SO
BB_SI
M18
M19
L18
H1
G2
J1
DPNVD, DPNHD, DPNCKO
SP
(PAGE 3-3)
KEY_AD3
9
XBB_RST
XBB_SCK
BB_SO
16
15
13
FP-808 FLEXIBLE
(PAGE 3-6)
XBB_SCK
BB_SO
KEY_AD2
BL_BRT
P_BL_ON
PANEL_O/C
PANEL_NOR/REV
KEY_AD2
KEY_AD0
XCS_LCD
TP_SEL1
TP_X
BL_BRT
P_BL_ON
PANEL_O/C
PANEL_NOR/REV
KEY_AD2
KEY_AD0
XCS_LCD
TP_SEL1
TP_X
TP_Y
FR_XRESET
XBATT_VIEW
Y2
Y4
G24
H25
AJ35
50
31
7
32
5
23
14
29
28
30
6
AH35
T27
B29
AM35
AN34
TP_Y
: VIDEO SIGNAL
: AUDIO SIGNAL
Q1701
TP_SEL2
TP SEL
SWITCH
B28
4
: VIDEO/AUDIO SIGNAL
CN1103 FP-809 FLEXIBLE BOARD
ATA_D0 - ATA_D15
ATA_A0 - ATA_A2
DD0 - DD15
DA0 - DA2
HARD
DISK
DRIVE
XATA_CS1, XATA_CS0, ATA_INTRQ, XATA_DMACK, ATA_IORDY, XATA_DIOR, XATA_DIOW, ATA_DMARQ
CS1-, CS0-, INTRQ, DMACK-, IORDY, DIOR-, DIOW-, DMARQ
RESET-
DASP-
HDD_UNLOAD
XATA_RESET
XATA_RESET
HDD_ACCESS
HDD_UNLOAD
AL4
51
11
1
BOOT_MODE_PORT0
D_2.8V
3
R1008
OVERALL (3/6)
(PAGE 3-3)
MEM_SEL1
MEM_SEL2
AG34
AF34
FR_XRESET
XBATT_VIEW
HDD_ACCESS
HDD_UNLOAD
XMS_IN
FP-805
FLEXIBLE
BOARD
MS-381 BOARD
R1019
R1009
CN1009
BOOT_MODE_PORT0
UART2_SI
UART2_SO
UART3_SI
CN1006
XMS_IN
CN7301
CN7302
BOOT_MODE_PORT0
UART2_SI
XMS_IN
7
5
4
3
2
AA1
H27
G27
J25
K26
10
22
13
1
6
UART2_SO
UART3_SI
UART3_SO
XMS_ACC_LED
XMS_ACC_LED
D7301
(ACCESS)
CPC
H23
UART3_SO
MEMORY
(For check)
MSX_BIO0 - MSX_BIO3
MSDATA0 - MSDATA3
MS_BS
STICK
PRO DUO
FB1801
FB1802
MSX_BS
MS_BS
AM31
AR32
2
21
9
2
8
MSX_CLK
MSX_CLK
MS_SCLK
14
HDR-SR11/SR11E/SR12/SR12E_L2
3-2
3-3. OVERALL BLOCK DIAGRAM (3/6) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
FP-799 FLEXIBLE BOARD
VC-516 BOARD (3/5)
FP-806
CR-089 BOARD
FLEXIBLE
BOARD
C13
CN1104
VIDEO/D3_PR
S_C/D3_PB
S_Y/D3_Y
AUDIO_L_I/O
AUDIO_R_I/O
CN7402
CN7401
15
C14 V_TO_PR
J7222
CN1002
A13
B12
B11
A12
D1
D2
VIDEO/D3_Pr
S_C/D3_Pb
S_Y/D3_Y
AUDIO_L
L1
20
22
24
10
12
26
24
22
36
34
EXT_MIC_L
MIC
2
4
C_TO_PB
M2
IC2801
EXT_MIC_R
19
20
3
(PLUG IN POWER)
Y_TO_Y
K1
AUDIO/VIDEO
PROCESSOR
(16/22)
AUDIO_L_I/O
AUDIO_R_I/O
IC_2401_Y_OUT
J7221
F2
G1
N4
N3
HP_R_OUT
HP_L_OUT
7
9
AUDIO_R
7
(headphone)
IC_2401_C/PB_OUT
Q2802
Q2803
HP MUTE
HP MUTE
IC_2401_Y_OUT
IC_2401_C/PB_OUT
IC_2401_PR_OUT
Y_TO_Y(S_Y/D3_Y)
C_TO_PB(S_C/D3_PB)
V_TO_PR(VIDEO/D3_PR)
ADA_LRCK
ADA_SIA0
ADA_FCK
ADA_BCK
2
4
6
35
33
31
7
B3
SP
11
CRADLE
HP_JACK_IN
OVERALL (2/6)
(Handycam Station)
11
(PAGE 3-4)
(PAGE 3-2)
XBB_SCK
BB_SO
XBB_SCK
BB_SO
J13
K13
22
23
USB_D+_CR
USB_D-_CR
USB_D+
USB_D-
5
7
41
39
6
8
CN1004
INT_MIC_L
IC2501
D4 DRIVER
(13/22)
3
1
5
B14
B13
A10
ADA_LRCK
ADA_SIA0
ADA_FCK
ADA_BCK
ADA_LRCK
M13
P12
N14
M14
N29
XBB_SCK
BB_SO
JACK_AD_CRADLE
KEY_AD3
ADA_SIA0
ADA_FCK
ADA_BCK
MULTI_JACK_IN
DISC_BURN (KEY_AD3)
LANC_SIG
MIC901
INT_MIC_R
INT_MIC_F
R29
M29
M28
14
2
16
32
44
30
11
1
12
KEY_AD3
MICROPHONE
UNIT
OVERALL (2/6) (PAGE 3-2)
LANC_SIG
MIC_JACK_IN
SYS_SOUND
XCS_IC2801
ADA_SOA0
MIC_JACK_IN
SYS_SOUND
XCS_IC2801
ADA_SOA0
L14
A4
J14
N13
P13
D23
R35
U26
N28
XCS_DDRA
T25
20
CN1003
SHOE_MIC_FL
SHOE_MIC_FR
FP-804
FLEXIBLE
BOARD
JK-356 BOARD
FP-802 FLEXIBLE BOARD
10
11
A11
B10
USB_D+_CR
USB_D-_CR
USB_D+_CN
USB_D-_CN
ADA_SOA1
ADA_SOA1
3
4
1
2
USB_D+
USB_D-
USB_SELECT
P29
W35
V35
AN7
8
7
9
IC1101
USB SW
(2/22)
XMIC_MONO
XSYS_RST
XMIC_MONO
CN1106
VIDEO/D3_PR
CN7201
CN7203
L13
K14
U24
VIDEO/D3_PR
S_C/D3_PB
S_Y/D3_Y
AUDIO_L
25
19
17
13
14
21
22
20
14
12
9
10
16
17
9
5
10
1
6
7
EXT_STOROBE_ON
IC1701
(3/4)
4
S_C/D3_PB
S_Y/D3_Y
AUDIO_L_I/O
AUDIO_R_I/O
JACK_AD
HOT
SHOE
KEY_AD3
JACK_AD
AH33
HP_JACK_IN
HOTSHOE_ID1
HOTSHOE_ID2
CPU
J26
AM34
AM33
OVERALL (2/6)
KEY_AD3
(6/22, 7/22, 8/22)
HOTSHOE_ID1
HOTSHOE_ID2
LANC_SIG
AV/ R
8
5
3
AUDIO_R
MULTI_JACK_IN
LANC_SIG
AJ34
LANC_SIG
2
XSYS_RST
XCS_EX
FR_SI
FR_SO
WD_DIS
XHOT_STBY
XFR_SCK
STABLE_RUN
GSENS_REF
XSYS_RST
XCS_EX
FR_SI
FR_SO
CN7202
USB_D+
USB_D-
USB_VCC
A8
H3
J4
L5
D9
E10
K5
E9
L8
G2
D22
B22
C22
G23
C23
A22
V2
AL33
IC4901
USB_D+_CN
USB_D-_CN
3
5
9
3
4
7
3
2
1
LANC PROCESSOR
(22/22)
X4901
32.768kHz
L2
L3
USB_VCC_CN
(USB)
WD_DIS
XHOT_STBY
XFR_SCK
STABLE_RUN
GSENS_REF
: VIDEO SIGNAL
: AUDIO SIGNAL
XQUICKREQ_LED
START/STOP
XPHOTO_LED
ZOOM_VR_AD
KEY_AD1
AN6
H26
AK3
AJ33
GSENS_Z
GSENS_Y
GSENS_X
10
9
8
AK35
AF35
AG35
BOOT_MODE_PORT0
GSENS_TEMP
H9
SE3202
G SENSOR
K7
5
AH34
HDD_UNLOAD
AP10
JACK_AD_CRADLE
CONTROL SWITCH BLOCK (PS28100)
J11
CN1007
D005
(QUICK ON)
XQUICKREC_LED
XQUICKREC_LED
14
2
S002
START/STOP
START/STOP
XPHOTO_LED
ZOOM_VR
START/
STOP
D002
(PHOTO)
XPHOTO_LED
ZOOM_VR_AD
QUICKREC_SW
PHOTO_FREEZE
PHOTO_REC
LANC_IN
LANC_OUT
VTR_DD_ON
B10
C10
F2
J3
5
J2
N5
N7
P3
IC4701
LANC_SIG
VTR_DD_ON
K3
RV001
T
POWER SUPPLY
(21/22)
19
12
17
16
W
FR_XRESET
K2
B8
S005
QUICKREC_SW
PHOTO_FREEZE
PHOTO_REC
(QUICK ON)
XFLASH_RST
S004
(PHOTO FREEZE)
FR_XRESET
PHOTO
HDD_UNLOAD
XBATT_VIEW
XMS_IN
S003
(PHOTO REC)
KEY_AD1
XBATT_VIEW
XMS_IN
B2
B6
D_2.8V
HDD_ACCESS
*1
R1026
OFF (CHG)
XPOWER_SW
XMODE_SW
XCHARGE_LED
XCAM_LED
XPOWER_SW
XMODE_SW
XPOWER_SW
XMODE_SW
SYSTEM_AD
GENERAL_AD
B4
A2
G11
F11
3
4
ON
POWER
K8
K11
MODE
*1
R1025
R1027
0
D004
/CHG)
XCHARGE_LED
XCAM_LED
XCHARGE_LED
XCAM_LED
(
9
7
*1
SR11
100K
22K
SR11E
22K
100K
SR12
100K
22K
SR12E
22K
100K
D003
R1026
R1027
(CAM)
D006
(ACCESS)
HDD_ACCESS
X_ACCESS_LED
11
HDR-SR11/SR11E/SR12/SR12E_L2
3-3
3-4. OVERALL BLOCK DIAGRAM (4/6) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
VC-516 BOARD (4/5)
FP-798 FLEXIBLE BOARD
CN1101
CN7191
TMDS_DATA2+
TMDS DATA2+
TMDS DATA2-
TMDS DATA1+
TMDS DATA1-
TMDS DATA0+
TMDS DATA0-
TMDS CLOCK+
TMDS CLOCK-
TMDS_DATA2_+
TMDS_DATA2_-
TMDS_DATA1_+
TMDS_DATA1_-
TMDS_DATA0_+
TMDS_DATA0_-
TMDS_CLOCK_+
TMDS_CLOCK_-
J10
K10
K8
K7
K5
K4
K2
K1
24
23
20
19
16
15
12
11
2
3
5
6
8
9
11
12
TMDS_DATA2-
TMDS_DATA1+
TMDS_DATA1-
TMDS_DATA0+
TMDS_DATA0-
TMDS_CLOCK+
TMDS_CLOCK-
HM_R0 - HM_R7
HM_Y0 - HM_Y7
HM_B0 - HM_B7
D0_HDMI - D23_HDMI
DE_HDMI, IDCK, HSYNC_HDMI, VSYNC_HDMI,
256FS_HDMI, ADAO2_HDMI, ADAO1_HDMI,
FS_HDMI, 64FS_HDMI
HDMI
OUT
SDA
SCL
CEC
SDA
SCL
CEC
SDA
SCL
CEC
G9
G10
J8
6
7
9
16
15
14
XHDMI_RST
F4
FB2701
HM_FLD
HM_VD
HM_HD
HM74CK
HMCK
CEC_INT
I2C_SDA
I2C_SCK
R21
U20
T21
P21
T20
C4
C6
C7
G1
E1
H10
F9
F10
G7
Q2704
LEVEL SHIFT
XCS_IC_2601
C2
HDMI_JACK_IN
HPD
HPD
HPD
IC2401
(2/2)
SOC
(12/22)
K3
3
19
SPDIF_O
E2
IC2601
HDMI PROCESSOR
(14/22)
IC2701
HDMI TRANSMITTER
(15/22)
XBB_SCK
BB_SO
F2
D2
D3
ADA_LRCK
E11
E10
D10
C11
ADA_BCK
ADA_FCK
ADA_SIA0
PCI_AD0 - PCI_AD31
3
4
IC1705
XPON_SW
BB_SI
XCS_IC_2601
XHDMI_RST
CEC_INT
I2C_SCK
I2C_SDA
C30
T26
A28
D31
AR12
AR13
H28
(PAGE 3-5)
WAVEFORM SHAPER
(6/22)
PCI_XBE0 - PCI_XBE3
IC1301
(2/3)
PCI_CLKRUN
PCI_PAR
N1
L5
M5
L2
N7
L1
P7
M1
P4
N5
P2
CPU
PCI_XFRM
PCI_XTRDY
PCI_XSERR
PCI_XDEVSEL
PCI_XPERR
PCI_XSTOP
PCI_XIRDY
PCI_XRESET
PCI_CLK
(SIGNAL
HDMI_JACK_IN
PROCESS)
(3/22, 4/22)
IC1702
WAVEFORM SHAPER
(6/22)
SPDIF_O
CLK_SYS_OUT_IC_2201
3
4
AA17
AC12
IC2201
B3
PCI PROCESSOR
(10/22)
A_2.8V
X1701
12MHz
PCI_AD0 - PCI_AD31
PCI_AD0 - PCI_AD31
IC_2201_DDR_D00 - IC_2201_DDR_D31
IC_2201_DDR_A00 - IC_2201_DDR_A13
PCI_XBE0 - PCI_XBE3
PCI_XBE0 - PCI_XBE3
PCI_CLKRUN
PCI_PAR
PCI_CLKRUN
PCI_PAR
AM19
AM15
AN13
AN14
AM13
AM14
AN17
AR19
AR21
AP19
AR16
AR17
A4
M4
K2
K4
M1
L2
M2
K3
K1
H1
J1
PCI_XFRM
PCI_XTRDY
PCI_XSERR
PCI_XDEVSEL
PCI_XPERR
PCI_XSTOP
PCI_XIRDY
PCI_XRESET
PCI_CLK
PCI_XFRM
PCI_XTRDY
PCI_XSERR
PCI_XDEVSEL
PCI_XPERR
PCI_XSTOP
PCI_XIRDY
PCI_XRESET
PCI_CLK
IC2301
MOBILE
DDR SDRAM
(11/22)
IC1701
(4/4)
IC_2201_DDR_DQS0 - IC_2201_DDR_DQS3,
IC_2201_DDR_DQM0 - IC_2201_DDR_DQM3
CPU
(6/22, 7/22, 8/22)
FR-278 BOARD
FP-812
FLEXIBLE
BOARD
XIC_2201_DDR_CLK, IC_2201_DDR_CLK,
XIC_2201_DDR_CS0, XIC_2201_DDR_RAS,
XIC_2201_DDR_CAS, XIC_2201_DDR_WE,
IC_2201_DDR_CKE1, IC_2201_DDR_BA0,
IC_2201_DDR_BA1
CN9002
YAW_AD
CN1102
YAW_AD
SE9001
PITCH SENSOR
6
5
16
17
20
12
11
10
1
2
3
IC_2201_DATA0 - IC_2201_DATA7
IC9001
SE9002
YAW SENSOR
16
VST_C_RESET
PITCH_AD
VST_C_RESET
PITCH_AD
PITCH/YAW
SENSOR
AMP
10
11
IC_2201_FLD, IC_2201_IVCLK,
IC_2201_MCK, IC_2201_LRCK
OVERALL (5/6)
(PAGE 3-5)
IC_2201_ADATA
PCI_XINTA_AN
PCI_XREQFS0_AN
PCI_XGNTTS0_AN
IC_2201_SYSCLK
J33
AR20
AM20
AP17
L35
AA16
A3
B2
B3
AC13
IC9002
FP-803
FLEXIBLE
BOARD
ST-185 BOARD
FLASH UNIT
(FL25500)
SIRCS_SIG
4
SIRCS_SIG
REMOTE
COMMANDER
RECEIVER
D_2.8V
1
1
7
12
6
Y3
T5001
2
CN5002
XE_A
D5003
L5001
IR_LED_ON
(PAGE 3-5)
Q1101
6
5
ST_UNREG
NS_LED_K
NS_LED_K
CN1005
CN5001
SCHARGE_ON
XSCHARGE_FULL
STROBO_ON
1
4
+
STRB_CHARGE
5
6
7
10
9
8
8
7
4
1
2
D9001
(NIGHTSHOT)
FLASH
UNIT
XSTRB_FULL
STROBE_ON
NS_LED_A
NS_LED_A
(PAGE 3-5)
6
2
7
D_2.8V
D_2.8V
3
IC5001
C5006
XTALLY_LED
XTALLY_LED
11
AM5
CHARGING
CAPACITOR
FLASH
CONTROL/
CHARGE
XE_K
D_2.8V
D9002
(TALLY)
5
8
CONTROL
Q5001
6
SWITCH
S001
(ADAPTER DETECT)
ADAPTOR_DET
ADAPTOR_DET
ADAPTER DETECT
ADAPTER DETECT
AP9
14
1
2
HDR-SR11/SR11E/SR12/SR12E_L2
3-4
3-5. OVERALL BLOCK DIAGRAM (5/6) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
CONTROL SWITCH BLOCK
(RS28900)
LD-230 BOARD
CN5104
DIAL_B
DIAL_A
DIAL_B
DIAL_A
3
4
PUSH MANUAL
S003
S002
Dial_B
FP-801
VC-516 BOARD (5/5)
XPON SW
XPON_SW
FLEXIBLE
BOARD
CAM
CTRL
5
2
S004
(BACKLIGHT)
CN5102
CN1105
S001
Dial_A
B_SW
BACKLIGHT_KEYAD
XPON_SW
XPON_SW
(PAGE 3-4)
49
51
3
1
BACKLIGHT_KEYAD
KEY_AD2
(PAGE 3-2)
DIAL_B
DIAL_A
DIAL_B
DIAL_A
47
48
5
4
AF13
AE13
CN5601
SHUTTER_XA
SHUTTER_XB
SHUTTER_A
LENS_COVER_OPEN
LENS_COVER_OPEN
LENS_COVER_LED_ON
1
4
3
2
8
9
45
46
7
6
AJ4
AC13
LENS_COVER_LED_ON
D_2.8V
LENS_COVER_LED_ON
LENS
BARRIER
LENS BLOCK (2/2)
SHUTTER_B
IR_LED_ON
14
AH4
LENS_COVER_OPEN
LENS_COVER_LED_ON
Q5601
(TO LENS BLOCK 1/2)
OVERALL (4/6)
(PAGE 3-4)
IRIS
MOTOR
CN5103
SHUTTER_XA
F2
DIRB0
DIRA0
DIRB0
DIRA0
IC5601
C5
C6
43
44
9
8
AE21
AC21
SHUTTER_XB
E6
I_DRIVE±
I_DRIVE±
I_DRIVE±
I_BIAS±
I_HALL±
SHUTTER
DRIVER
(4/4)
M
SHUTTER_A
F3
EN0
EN0
42
10
AC20
SHUTTER_B
D6
I_BIAS±
I_BIAS±
IC1301
H
(3/3)
XSYS_RST
12
I_HALL±
I_HALL±
AC5
CPU
(SIGNAL
PROCESS)
(3/22, 4/22)
DIRB1
DIRA1
DIRB1
DIRA1
OVERALL (3/6)
(PAGE 3-3)
J9
M9
11
10
41
42
AC23
AF22
ND FILTER
MOTOR
ND_DRIVE±
ND_BIAS±
ND_HALL±
ND_DRIVE±
ND_BIAS±
ND_HALL±
ND_DRIVE±
ND_BIAS±
ND_HALL±
EN1
EN1
M
STRB_CHARGE
XSTRB_FULL
STROBE_ON
40
12
AJ26
AC11
AJ5
AE20
(PAGE 3-4)
H
3
1
IC5206
NF_EN
L8
4
EX OR
(2/4)
D1301
D1302
FOCUS MOTOR
NF_EN
NF_EN
EXT_STOROBE_ON
28
24
AC9
AC22
FOCUS±
FOCUS±
FOCUS±
M
F_MR_A,
F_MR_B
F_MR_A,
F_MR_B
F_MR_A,
F_MR_B
NF_SW
NF_SW
XRST_IC_5201
FOCUS MR
SENSOR
M8
H11
29
31
23
21
AF7
AF5
XRST_IC_5201
IC5201
ZOOM_A,
ZOOM_B,
ZOOM_XA,
ZOOM_XB
ZOOM_A,
ZOOM_B,
ZOOM_XA,
ZOOM_XB
ZOOM_A,
ZOOM_B,
ZOOM_XA,
ZOOM_XB
ZOOM AND FOCUS
DRIVE
ZOOM MOTOR
(2/4)
M
Z_MR_A,
Z_MR_B
Z_MR_A,
Z_MR_B
Z_MR_A,
Z_MR_B
ZOOM MR
SENSOR
EXT_CAM_VD
SYS_V
SSS
XCAM_SCK
CAM_SO
CAM_SI
XCS_IC_5201
IC_5201_VD
IC_5501_CLK
XCAM_SCK
CAM_SO
CAM_SI
XCS_IC_5201
IC_5201_VD
H12
J11
K11
J12
L12
K12
12
14
13
21
26
40
38
39
31
26
AC1
Y7
AB5
AC2
AC18
AF20
AB4
AA5
AB1
1
NF MOTOR
OVERALL (1/6)
(PAGE 3-1)
NF_DRIVE±
NF_DRIVE±
NF_DRIVE±
XWEN
M
TEMP_OUT
LENS_TEMP_AD
LENS TEMP
SENSOR
19
38
CN1008
OPTICAL IMAGE STABILIZER
CAM_UART_TXD
CAM_UART_RXD
IC_1301_1_CS
CAM_UART_TXD
AH2
AH3
AB11
2
3
4
5
6
7
LENS_TEMP_AD
THERM
LENS_TEMP_AD
THERM
23
25
29
27
AE11
CAM_UART_RXD
IC_1301_1_CS
IC_5501_SI
IC_5501_SO
IC_5501_SCK
THERM
THERM
OIS TEMP
SENSOR
AE9
CPC
INB_PITCH
INA_PITCH
B3
B4
E2
G2
IC_5501_CLK
IC_5501_SO
IC_5501_SI
XCS_IC_5501
IC_5501_SCK
IC_5501_CLK
IC_5501_SO
IC_5501_SI
XCS_IC_5501
IC_5501_SCK
XRST_IC_5501_CPU
IC5502
A3
16
22
20
19
24
30
36
30
32
33
28
22
AJ3
AA7
AD1
AC4
AD2
AB10
PITCH
MOTOR
PITCH±
PITCH±
(For check)
M
PITCH DRIVER
(3/4)
A4
B4
A5
B5
A6
C2
PITCH_OUT
PITCH_IN
PITCH_HALL±
PITCH_HALL±
HALL
ELEMENT
XRST_IC_5501_CPU
PITCH_HALLBIAS±
PITCH_HALLBIAS±
XSYS_RST
XSYS_RST
A7
C9
33
27
19
25
IC5501
PWM_OUT_PITCH
PWM_OUT_YAW
IC5504
7
2
1
6
F2
F9
STEADYSHOT
PROCESSOR
(3/4)
EXT_CAM_VD
EXT_CAM_VD
INVERTER
(3/4)
C2
IC5503
YAW_AD
PITCH_AD
VST_C_RESET
YAW_AD
PITCH_AD
VST_C_RESET
YAW
MOTOR
YAW±
YAW±
J5
G5
D5
36
39
32
16
13
20
INA_YAW
INB_YAW
M
16
YAW DRIVER
(3/4)
B4
B3
G9
E9
OVERALL (4/6)
(PAGE 3-4)
YAW_OUT
YAW_IN
YAW_HALL±
YAW_HALL±
HALL
ELEMENT
YAW_HALLBIAS±
YAW_HALLBIAS±
HDR-SR11/SR11E/SR12/SR12E_L2
3-5
3-6. OVERALL BLOCK DIAGRAM (6/6) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
SP901
(SPEAKER)
1, 2
FP-807 FLEXIBLE
BOARD
PD-343 BOARD
LCD901 (1/2)
CK-185 BOARD
CN5803
CN5907
R0_T - R7_T
G0_T - G7_T
CN5801
SP
IC5901
LCD DRIVE
CN5802
CN5901
B0_T - B7_T
D0± - D2±, CLK±
D0+_T - D2+_T, D0-_T - D2-_T, CLK+_T, CLK-_T
VS_T, HS_T, DCLK_T
3.2 inch
WIDE
COLOR
LCD
: VIDEO SIGNAL
: AUDIO SIGNAL
XBB_RST
BB_SO
XSCK
XBB_RST
XBB_RST_T
BB_SO_T
XSCK_T
XBB_RST_T
BB_SO_T
XSCK_T
XCS_T
UNIT
16
13
15
14
36
39
37
38
36
39
37
38
8
5
6
7
39
BB_SO
XSCK
XCS
XCS
XCS_T
TCOM2
Q5907 - Q5910
CN5906
TCOM1
BL_BRT
P_BL_ON
BL_BRT
P_BL_ON
BL_BRT_T
P_BL_ON_T
1
1
50
31
2
21
2
21
BACKLIGHT
DRIVE
CN5905
BL_L
EP_2.8V_T
BL_-V_T
BACKLIGHT
LED
CN5902
TP_X_T
TP_Y_T
TP_X
TP_Y
TP_X
TP_Y
TP_X_T
TP_Y_T
LCD901 (2/2)
28
30
24
22
24
22
5
2
TOUCH
PANEL
FP-808 FLEXIBLE
(PAGE 3-2)
TOUCH
PANEL
I/F
TP_SEL1
TP_SEL1
TP_SEL1_T
TP_R
TP_BOT
29
23
23
1
4
Q5901, Q5902
FP-454 FLEXIBLE BOARD
CN5909
IC001
PANEL_NOR/REV
PANEL_NOR/REV
KEY_AD0
PANEL_NOR/REV
KEY_AD0
PANEL_NOR/REV
PANEL_NOR/REV
PANEL
REVERSE
DETECT
4
5
32
20
29
20
29
CN5903
HOME_SW
S004
HOME
S003
W
S002 (ZOOM)
T
KEY_AD0
KEY_AD2
23
5
6
5
4
3
2ND_ZOOM(W)
2ND_ZOOM(T)
2ND_S/S_SW
S5804
W
T
S001
START/STOP
S5802
EASY
CONTROL SWITCH BLOCK
(SB28900)
S5803
S5806
PANEL
PANEL_O/C
FR_XRESET
XBATT_VIEW
7
6
4
OPEN/CLOSE
S5801
RESET
S5805
DISP/
BATT INFO
S5808
NIGHTSHOT
KEY_AD3
OFF
ON
9
HDR-SR11/SR11E/SR12/SR12E_L2
3-6
3-7. POWER BLOCK DIAGRAM (1/3)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
VC-516 BOARD (1/3)
F4601
HDD_UNREG
L4711
CN1001
CMOS_A_3.3V
D_1.5V
F4602
ACV_UNREG_CN
MT_BL_UNREG
J901
DC IN
2
3
1
BATT/XEXT_CN
F4603
D_2.8V
A_2.8V
MT_5.0V
EP_1.8V
D_1.8V
VTR2_UNREG
F4604
VTR_UNREG
Q4601,
Q4602
Q4603,
Q4604
Q4605, Q4606
F4605
F4607
SHOE_UNREG
ST_UNREG
D4601
A_1.8V
CR-089
BOARD
FP-806
FLEXIBLE
BOARD
SHOE_ON
BATT_LI_3V
D_1.2V
CN1104
CN7401 CN7402
L4713
A_1.2V
D_3.3V
PVDD1a
PVDD1b
LX1a
LX1b
IN1 H13
BATT/XEXT_CR
23
20
26
R1 VBATT
R2 VCH
L4701
L4702
L4703
L4704
L4705
L4706
L4707
IC_1301_D_1.2V
3.3V_OUT
D4702
CRADLE
(Handycam Station)
ACV_UNREG_CN
Q4709(1/2)
MUTE
HDD_PON
LANC_DC
USB_VCC_CR
16
2
28
45
18
1
USB_DET_VBUS
SHOE_UNREG
ST_UNREG
PVDD2a
PVDD2b
LX2a
LX2b
IN2 E3
F4606
BATT_UNREG
L4714
D_1.5V
N1 B_UNREG
L2 LANC_DC
(5.6V)
JK-356
BOARD
FP-804
FLEXIBLE
BOARD
HDD_3.3V
SWITCH
Q4715, Q4716, Q4718
PVDD3a
PVDD3b
LX3a
LX3b
IN3 J13
CN1106
USB_VCC_CN
CN7202 CN7201
VCC
1
4
7
9
L4715
L4719
L4723
L4726
L4716
L4721
L4724
EP_2.8V
D_2.8V
AU_2.8V
A_2.8V
(USB)
AV/ R
CN7203
DVDD4
AVDD3
Q4708
LOAD SWITCH
Q4709(2/2)
LANC_DC
LANC_DC
VTR_UNREG
18
23
AVDD1
V_UNREG
PVDD4a
PVDD4b
LX4a
LX4b
IN4 N11
MUTE
IC4601
EP_4.6V
AU_4.6V
A_4.6V
POWER ON RESET
(20/22)
XUNREG_RESET
C2 P06_INT10
VTR_UNREG
1
VDD
2
OUT
PVDD5a
PVDD5b
LX5a
LX5b
IN5 C8
L4728
MT_5.0V
BATT/XEXT_CR
BATT/XEXT_CN
FAST_CHARGE
INIT_CHARGE_ON
B1 P05_INT09
C7 P71_INT01
E11 P53
PVDD6a
PVDD6b
LX6a
LX6b
IN6 N10
P30_AN00 J5
P31_AN01 L6
CN1001
BATT_UNREG_CN
L4725
EP_1.8V
F10 P52
+
Q4710
4
5
6
AVCC
L4717
L4720
BH901
D_1.8V
A_1.8V
BATT_SIG
LOAD SWITCH
AVR
VCC2
VCC1
VOUT
BATTERY
TERMINAL
A4 SIO2
C
-
M2 VOUT
(
)
Q4713
MUTE
PVDD7a
PVDD7b
LX7a
LX7b
IN7 F3
Q4707
LOAD SWITCH
Q4712
MUTE
D4708
VB B1
OUT11 R15
PVDD11 A2
DVDD1 A1
DVDD2 A12
D4706
D4707
IC4901
LANC PROCESSOR
(22/22)
IC4702
PVDD8a
PVDD8b
LX8a
OP AMP
(21/22)
L4708
D_1.2V
LX8b
Q4714
5
VCC
MUTE
+
-
1
3
IN8 C7
4
OUT
IC4701
POWER SUPPLY
(21/22)
Q4704
L4709
SWITCH
Q4705
MUTE
OUT9-1 A13
OUT9-2 A14
Q4711
L4729
D_3.3V
BL_-V
CAP_IN A11
LOAD SWITCH
P11_SO1
DIN
CLK
LD
P12_SCK1
FR_EVER_SO, FR_EVER_SCK, XCS_DD
1.8/3V_GATE_CTRL
P21_PPG01
XLANC_PWR_ON
XLANC_ON
CH9_SW1 C10
DVDD3 D15
P07_INT11 C1
P23 H2
L3 WAKEUP
M3 XCTL2
Q4706
L4731
SWITCH
D4705
Q4702
Q4703
OUT10-1 C15
SD1 N9
VREF(2.5V) P5
CH6_SW N12
VRO P2
BATT_IN
P70_INT00 A7
N2 CS_OUT
VOUT3 B2
Q4701
BL_CONT
EVER_3.0V
EP_8.5V
LOAD SWITCH SIG GEN
CLAMP_ON
1.8/3VCTRL
P22 G2
P61_PPG11 C11
HDR-SR11/SR11E/SR12/SR12E_L2
3-7
3-8. POWER BLOCK DIAGRAM (2/3)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
FP-808
CK-185
FP-807
FLEXIBLE
BOARD
PD-343 BOARD
VC-516 BOARD (2/3)
FLEXIBLE BOARD
BOARD
IC3301
L3302
LCD901
EP_1.8V
27 bit DISPLAY SERIAL
INTERFACE TRANSMITTER
(19/22)
Q5901, Q5902
CN3301
D_2.8V
BL_-V
CN5801 CN5802
D_2.8V
BL_-V
EP_1.8V
CN5901
D_2.8V_T
BL_-V_T
EP_1.8V
TOUCH
17
22
18
17
22
18
35
30
34
35
30
34
PANEL I/F
BL_-V
EP_1.8V
CN5907
L5903
L5901
3.2 inch
WIDE
EP_1.8V
10
1
COLOR
LCD UNIT
EP_2.8V
EP_2.8V
EP_2.8V
EP_2.8V_T
Q5907 - Q5910
BL_CONT
BL_CONT
BL_CONT
BL_CONT_T
CN5905
BL_L
51
51
1
1
BACKLIGHT
DRIVE
BACKLIGHT
LED
L3101
EP_2.8V
IC3101
FP-802 FLEXIBLE BOARD
EVF DRIVER
(17/22)
L5902
CN1003
SHOE_UNREG
IC5901
SHOE_UNREG
HOT
SHOE
LCD DRIVE
FP-811 FLEXIBLE BOARD
BL-017 BOARD
CN5701
LCD902
COLOR
EVF
CN3101
CN5702
L3103
L3102
EP_8.5V
EP_4.6V
EVF_VDD
EP_4.6V
18
2
18
2
2
UNIT
D5701
(EVF BACKLIGHT)
D_1.8V
D_1.8V
A_4.6V
IC2701
L2701
L2702
HDMI
TRANSMITTER
(15/22)
L2501
L2502
A_4.6V
A_2.8V
IC2501
L2503
A_2.8V
D_2.8V
D4_-2.8V
D4 DRIVER
(13/22)
D_3.3V
D_3.3V
D_2.8V
D_1.5V
IC2601
FP-809 FLEXIBLE
BOARD
FB2601
L4781
HDMI
PROCESSOR
(14/22)
CN1103
HDD_3.3V
A
HARD
DISK
DRIVE
D_1.5V
POWER (1/3)
(PAGE 3-7)
IC4781
D4_-2.8V
A3
D_2.8V
-2.8V REG
(21/22)
CONTROL SWITCH BLOCK (PS28100)
C2
CN1007
ACCESS_LED_VDD
HDD_3.3V
EVER_3.0V
ACCESS_LED_VDD
D006
(ACCESS)
10
EVER_3.0V
CHARGE_LED_VDD
MODE_LED_VDD
D004
/CHG)
8
6
(
D002
(PHOTO)
D_2.8V
L2804
MODE_LED_VDD
D_2.8V
D003
(CAM)
Q2801
SWITCH
MT_5.0V
IC2801
QUICKREC_LED_VDD
D_2.8V
QUICKREC_LED_VDD
D_2.8V
D005
13
20
L2802
(QUICK ON)
AU_4.6V
AU_2.8V
VIDEO, AUDIO
PROCESSOR
(16/22)
L2803
L2805
L2801
A_2.8V
A_2.8V
RV001
W
T
(ZOOM)
IC2702
FP-798 FLEXIBLE BOARD
5V REG (15/22)
CN1101
5VPOWER
CN7191
D_2.8V
D_1.8V
D_3.3V
A_1.8V
D_1.2V
D_2.8V
ST_UNREG
1
5
HDMI
OUT
4
18
IC2201
PCI
PROCESSOR
(10/22)
FP-803 FLEXIBLE
BOARD
FLASH UNIT (FL25500)
ST-185 BOARD
A_1.8V
D_1.2V
T5001
CN1005
CN5001
L5001
CN5002
XE_A
D5003
ST_UNREG
ST_UNREG
FLASH
UNIT
IC5001
L1001
FLASH CONTROL/
CHARGE CONTROL
MT_5.0V
MT_5V
9
6
HDR-SR11/SR11E/SR12/SR12E_L2
3-8
3-9. POWER BLOCK DIAGRAM (3/3)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
FP-801
FLEXIBLE
BOARD
LD-230 BOARD
VC-516 BOARD (3/3)
IC5205
LENS BLOCK
2.8V REG (2/4)
CN1105
CMOS_A_3.3V
CN5102
CMOS_A_3.3V
CN5103
F_MR_VCC
MR_A_2.8V
CMOS_A_3.3V
4
IN
OUT
3
44
45
8
7
15
D_1.5V
D_1.5V
MT_5.0V
D_2.8V
D_1.5V
MT_5.0V
D_2.8V
Z_MR_VCC
22
MT_5.0V
MT_5.0V
FB5201
IC5201
43
9
MR_A_2.8V
ZOOM AND FOCUS
DRIVE
SHOE_ON
HDD_PON
3.3V_OUT
AP11
EXIO/CF_ADDR[9]
D_2.8V
USB_VCC_CN
USB_VCC_CR
(2/4)
AM6 EXIO_DREQ
Q1103
Q1102
XVBUS_DET_CN
XVBUS_DET_CR
C
GPIO_S[2] G25
FB2001
D_1.2V
D_3.3V
A_1.2V
(PAGE 3-7)
IC5206
EX OR
(2/4)
FB2004
FB2005
FB2002
FB2003
GPIO_S[12] J21
D_2.8V
IC5502 IC5503
PITCH SENSOR, YAW DRIVER (3/4)
D_1.8V
IC1701
CPU
(6/22, 7/22, 8/22)
D_2.8V
MT_5.0V
C4 VCC
B1 VM
IC1001
MEMORY STICK 2.9V REG
(1/22)
FB1701
FB1702
A_2.8V
D_3.3V
A_2.8V
IC5504
MS_PWR_ON
INVERTER (3/4)
GPIO_S[14] H20
1
4
CE
VDD
D_3.3V
VOUT
3
D_2.8V
8
VCC
D_1.5V
IC5501
D_2.8V
STEADYSHOT
PROCESSOR
(3/4)
MT_5.0V
D_2.8V
IC2101
512M SDRAM,
512M OneNAND FLASH
(9/22)
D_2.8V
IC5601
SHUTTER DRIVER
(4/4)
L5601
IC1101
D_3.3V
D_3.3V
USB SW
(2/22)
B
BATT_LI_3V
FP-805
FLEXIBLE
BOARD
MS-381
BOARD
POWER (1/3)
(PAGE 3-7)
D_2.8V
CN7301
CN7302
CN1006
IC_1301_D_1.2V
IC_1301_D_1.2V
MEMORY
STICK
PRO DUO
MS_VCC
MS_VCC
6
VCC
17
20
21
9
IC1301
CPU
(SIGNAL PROCESS)
(3/22)
D_2.8V
ACCESS_LED_A
D_1.8V
A_2.8V
3
2
L1502
D7301
(ACCESS)
BATT_LI_3V
BT7301
3V
L1501
A_1.2V
A_2.8V
(POWER)
(4/22)
A_1.8V
L1301
SE3202
G-SENSOR
CM-094 BOARD
IC1303
L1302
5
BUFFER
(3/22)
IC6803
4
IN
OUT
3
CN1301
CMOS_A_3.3V
CN6801
CMOS_A_3.3V
D_1.8V
LVDS_I/O_1.8V
IC6804
CMOS IMAGER
2.7V REG
37
38
39
4
3
2
D_1.8V
I/O_1.8V
IC1601
IC2301
MOBILE
DDR SDRAM
(5/22)
MOBILE
DDR SDRAM
(11/22)
FP-812
FLEXIBLE
BOARD
FR-278 BOARD
CN1102
CN9002
A_2.8V
L9001
IC9001
A_2.8V
A_2.8V
5
8
8
5
PITCH/YAW
SENSOR AMP
D_2.8V
D_2.8V
D_2.8V
IC9002
VCC
1
REMOTE COMMANDER
RECEIVER
L2403
A_2.8V
IC1702
WAVEFORM SHAPER
(6/22)
L2404
EP_1.8V
D9002
(TALLY)
FB2401
D_1.2V
IC2401
L2401
L2402
IC1705
A_1.2V
SOC
(12/22)
WAVEFORM SHAPER
(6/22)
CN1008
D_2.8V
8
8
CPC
(For check)
CN1009
D_2.8V
CPC
(For check)
HDR-SR11/SR11E/SR12/SR12E_L2
3-9E
4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM
TO CRADLE
(Handycam Station)
LEVEL3
CM-094 BOARD
LEVEL3
LD-230 BOARD
BT7301
LITHIUM STORAGE
MS-381 BOARD
CONTROL
SWITCH
BLOCK
W
T
CN7401
(MULTI CONNECTOR)
(SIDE B)
FP-712 flexible board is not supplied,
(
)
BATTERY
but this is included in LENS BARRIER UNIT.
FP-712 FLEXIBLE
BOARD
(SB28900)
CR-089
BOARD
(SIDE B)
CONTROL
SWITCH
BLOCK
LCD901
(RS28900)
SP901
(SPEAKER)
34
CN7401
2
33
1
BH7301
BATTERY
HOLDER
TOUCH
PANEL
CN5903
36
35
LENS
BARRIER
(
)
6
1
IC6804
(not supplied)
CK-185 BOARD
CR-089
BOARD
(SIDE A)
2
1
44
45
CN7402
LENS BLOCK
1
40
CN6801
42
41
10
1
50
51
2
PD-343 BOARD
CN5102
1
3.2 INCH
WIDE COLOR
LCD UNIT
CN7302
MEMORY STICK
CONNECTOR
(
)
FP-807 FLEXIBLE BOARD
FR-278
BOARD
12
1
12
11
BH901
CN9002
FP-801 FLEXIBLE BOARD
BATTERY
TERMINAL
BACKLIGHT
LED
(
)
1
6
MS-381 BOARD
(SIDE A)
CN5909
J901
DC IN
C
6
1
FP-454 FLEXIBLE
BOARD
50
51
2
1
CN1105
CN1102
1
12
51
50
1
45
44
1
2
CN3301
CN1104
CN1001
2
42
41
CN1301
40
1
6
1
1
FP-803 FLEXIBLE BOARD
FP-798
FLEXIBLE
BOARD
CN7191
1
CPC
(For Check)
CN5001 13
14
HDMI
OUT
2
26
LEVEL3
VC-516 BOARD (SIDE A)
IC2101
(not supplied)
ST-185 BOARD
(SIDE A)
1
12
1
22
CN1007
1
6
CN1003
1
18
CN3101
CN1004
LEVEL3
VC-516 BOARD (SIDE B)
ST-185 BOARD
(SIDE B)
HARD DISK
DRIVE
CONTROL
SWITCH
BLOCK
FP-809 FLEXIBLE BOARD
FP-799
FLEXIBLE
BOARD
MIC901
MICROPHONE
UNIT
(
)
(PS28100)
CN5002
18
1
J7221
(HEADPHONE)
FLASH UNIT
(FL25500)
BL-017
BOARD
HOT SHOE
J7222
MIC
(PLUG IN POWER)
CN5701
CN5702
18
1
CN7201
1
20
Active
Interface Shoe
2
1
20
21
JK-356 BOARD
6
8
9
1CN72025
13
11
4
8
3
7
10
5
9
2
6
1
CN7203
7
14
12
LCD902
COLOR
EVF UNIT
CN7202
(USB)
CN7203
A/V
R
HDR-SR11/SR11E/SR12/SR12E_L2
FRAME
4-1
4-2. SCHEMATIC DIAGRAMS
Link
PD-343 BOARD
(LCD DRIVE)
FP-804 FLEXIBLE BOARD
(VC-JK CONNECTION)
FR-278 BOARD
(PITCH/YAW SENSOR AMP, REMOTE COMMANDER RECEIVER)
FP-805 FLEXIBLE BOARD
(VC-MS CONNECTION)
CK-185 BOARD
(CONTROL SWITCH)
FP-806 FLEXIBLE BOARD
(VC-CR CONNECTION)
ST-185 BOARD
(FLASH DRIVER)
FP-807 FLEXIBLE BOARD
(PD-CK CONNECTION)
JK-356 BOARD
(JACK)
FP-809 FLEXIBLE BOARD
(HDD CONNECTION)
CR-089 BOARD
(CRADLE TERMINAL)
FP-808 FLEXIBLE BOARD
(VC-CK CONNECTION)
BL-017 BOARD
(EVF, EVF BACKLIGHT)
FP-811 FLEXIBLE BOARD
(BL-VC CONNECTION)
MS-381 BOARD
(MS CONNECTOR)
FP-812 FLEXIBLE BOARD
(VC-FR CONNECTION)
FP-454 FLEXIBLE BOARD
(PANEL REVERSE DETECT)
CONTROL SWITCH BLOCK
(RS28900)
FP-798 FLEXIBLE BOARD
(HDMI CONECTOR)
CONTROL SWITCH BLOCK
(SB28900)
FP-799 FLEXIBLE BOARD
(HP, MIC JACK)
CONTROL SWITCH BLOCK
(PS28100)
FP-801 FLEXIBLE BOARD
(LD-VC CONNECTION)
FLASH UNIT
(FL25500)
FP-802 FLEXIBLE BOARD
(HOT SHOE CONNECTION)
FP-712 FLEXIBLE BOARD
(BARRIER UNIT CONNECTION)
FP-803 FLEXIBLE BOARD
(VC-ST CONNECTION)
COMMON NOTE FOR SCHEMATIC DIAGRAMS
HDR-SR11/SR11E/SR12/SR12E_L2
4-2. SCHEMATIC DIAGRAMS
ENGLISH
JAPANESE
4-2. SCHEMATIC DIAGRAMS
(ENGLISH)
THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS
(In addition to this, the necessary note is printed in each block)
(For schematic diagrams)
1. Connection
• All capacitors are in µF unless otherwise noted. pF : µ
µF. 50 V or less are not indicated except for electrolytics
and tantalums.
• Chip resistors are 1/10 W unless otherwise noted.
kΩ=1000 Ω, MΩ=1000 kΩ.
• Caution when replacing chip parts.
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum
capacitor, Because it is damaged by the heat.
• Some chip part will be indicated as follows.
Pattern box
Color bar chart
For PTB-450:
J-6020-250-A
Pattern box PTB-450
J-6082-200-A
or
Small pattern box
PTB-1450
For PTB-1450:
J-6082-559-A
J-6082-557-A
L = 1 m (PTB-450)
L = 40 cm (PTB-1450)
Example
C541
22U
TA A
L452
10UH
2520
Pattern box
Front of the lens
L
Camera
Kinds of capacitor
External dimensions (mm)
Case size
• Constants of resistors, capacitors, ICs and etc with XX
indicate that they are not used.
In such cases, the unused circuits may be indicated.
• Parts with # differ according to the model/destination.
Refer to the mount table for each function.
• All variable and adjustable resistors have characteristic
curve B, unless otherwise noted.
2. Adjust the distance so that the output waveform of
Fig. a and the Fig. b can be obtain.
H
• Signal name
XEDIT → EDIT
PB/XREC → PB/REC
• 2: non flammable resistor
• 5: fusible resistor
• C: panel designation
• A: B+ Line
A B
A=B
B
A
• B: B– Line
•
J : IN/OUT direction of (+,–) B LINE.
Fig. a (Video output terminal output waveform)
Electronic beam scanning frame
• C: adjustment for repair.
• A: not use circuit
(Measuring conditions voltage and waveform)
• Voltages and waveforms are measured between the
measurement points and ground when camera shoots
color bar chart of pattern box.They are reference values
and reference waveforms.
CRT picture frame
(VOM of DC 10 MΩ input impedance is used)
• Voltage values change depending upon input
impedance of VOM used.)
Fig.b (Picture on monitor TV)
Precautions for Replacement of Imager
• If the imager has been replaced, carry out all the adjustments
for the camera section.
• As the imager may be damaged by static electricity from
its structure, handle it carefully like for the MOS IC.
In addition, ensure that the receiver is not covered with
dusts nor exposed to strong light.
When indicating parts by reference number, please
include the board name.
The components identified by mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque 0 sont
critiques pour la sécurité.
Ne les remplacer que par une pièce portant le numéro
spécifie.
HDR-SR11/SR11E/SR12/SR12E_L2
4-2
ENGLISH
JAPANESE
4-2. SCHEMATIC DIAGRAMS
(JAPANESE)
回路図共通ノート
（他に必要なノートは各ブロックに記載してあります）
【回路図ノート】
1.接続図
・ケミコン，タンタルを除くコンデンサで，耐圧50V以下のもの
はその耐圧を省略。単位はすべてμF（pはpF）。
・チップ抵抗で指示のないものは，1／10W 以下。
kΩ＝1000Ω，M Ω＝1000kΩ
パターンボックス
カラーバーチャート
For PTB-450:
J-6020-250-A
Pattern box PTB-450
J-6082-200-A
or
Small pattern box
PTB-1450
・チップ部品交換時の注意
For PTB-1450:
J-6082-559-A
取り外した部品は再使用せず，未使用の部品をご使用くださ
い。
J-6082-557-A
タンタルコンデンサのマイナス側は熱に弱いため注意してくだ
さい。
L = 1 m (PTB-450)
L = 40 cm (PTB-1450)
・チップ部品には下記のように表示したものがあります。
例
C 541
22U
TA
L 452
パターンボックス
レンズ前面
カメラ
10UH
A
2520
L
↑
↑
↑
種類 ケースサイズ
外形寸法（m m ）
・抵抗，コンデンサ，ICなど定数にXXがあるものは，使用して
いない事を示しています。このため，使用していない回路が記
載されている事があります。
2.図a及び図bの波形が得られるように画枠調整して下さい。
H
・★印のある部品は，機種などにより異なりますので機能別マウ
ント一覧表を参照してください。
マ
ゼ
ン
ダ
シ
ア
ン
・可変抵抗と半固定抵抗で，B特性の表示を省略。
・信号名表記について，下記のような場合があります。
XEDIT → EDIT PB/XREC → PB/REC
・2は不燃性抵抗。
黄
白
緑
赤
青
・1はヒューズ抵抗。
・Cはパネル表示名称。
・AはB＋ライン。
A B
A=B
B A
・BはB－ライン。
・JはBライン（＋，－）の入出力方向を示す。
・Cは調整名称。
図a（映像入出力端子出力波形）
電子ビーム走査線
・Aは未使用回路。
【電圧・波形測定条件ノート】
・電圧値及び信号波形はパターンボックスのカラーバーチャート
を被写体としたときの測定点対アース間の参考値。
（デジタルマルチメータ；入力インピーダンス DC10M Ω使
用）
ブラウン管の画像枠
・使用テスタの入力インピーダンスにより電圧値が多少異なりま
す。
図b（テレビモニタの映像）
イメージャ交換時の注意
・イメージャを交換した場合は，カメラ部の全調整を
行ってください。
0印の部品，または0印付きの点線で囲まれた部品は，
安全性を維持するために重要な部品です。
従って交換時は，必ず指定の部品を使用して下さい。
・イメージャは構造上，静電気により破壊される恐れが
あるため，M OS ICと同様に注意して取り扱ってくだ
さい。
お願い
図面番号で部品を指定するときは基板名又はブロック
を併せて指定して下さい。
また，受光部にはゴミの付着，および強い光がはいる
ことのないように注意してください。
HDR-SR11/SR11E/SR12/SR12E_L2
4-3
Schematic diagrams of the CM-094, VC-516 and LD-230 boards are not shown.
Pages 4-4 to 4-30 are not shown.
HDR-SR11/SR11E/SR12/SR12E_L2
1
2
3
4
5
6
7
8
9
10
11
12
6P CN5903
CN5909 6P
CN5906 29P
D_2.8V_T
KEY_AD0
CONTROL
HOME_SW
6
5
4
3
2
1
D_2.8V
N.C.
6
5
4
3
2
1
TCOM1
VSS
1
SWITCH
BLOCK
2ND_ZOOM(W)
2ND_ZOOM(T)
2ND_S/S_SW
FP-454
2
R5902
1500
FLEXIBLE
PANEL_NOR/REV
REG_GND
A
B
C
D
E
A
B
C
D
E
F
PANEL_NOR/REV
N.C.
R5922
XX
2200
GVDD_IN
GVSS_IN
COMC
R5901
PAGE 4-36
of LEVEL2
3
VD5902
XX
LND001-LND006
PAGE 4-42
of LEVEL2
R5903
1200
4
REG_GND
REG_GND
N.C.
C5909
10u
5
REG_GND
REG_GND
COMDC
COMH
VGMH
SGND
SGND
VRCP2
VRCP1
VGH
6
C5913 4.7u
1u
R5923
10k
7
C5920
C5912
8
0.1u
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
EP_2.8V
C5921 1u
C5914 2.2u
C5915
2.2u
C5922
2.2u
D5903
MA2SD320G8S0
C21P
C21M
VGL
R5934
XX
C5930
2.2u
2.2u
C5917
VCL
D5904
MA2SD320G8S0
C31M
C31P
VR
R5933
XX
C5923
2.2u
Q5906
XX
R5935
XX
C5918
4.7u
C12P
C12M
C11P
C11M
C13M
C13P
C14M
C14P
VS
C5924
2.2u
C5931
XX
D8 D9 E8 E9 F8 F9 G8 J9 G9 H7 H9 H8 J8 J7 J2 H6 J1 G2 H4 E2
C5925
2.2u
R5930
XX
LND001
CH_GND
C5926
2.2u
REG_GND
B6_T
B7_T
G0_T
G1_T
G2_T
G3_T
G4_T
G5_T
G6_T
G7_T
B6
VDD_LVDS
C5927
2.2u
B7
VDD_LVDS
VDD_PLLA
VDD_PLLD
CPOL
LS1
39P
CN5901
G0
G1
G2
G3
G4
G5
G6
G7
GND
R0
R1
R2
R3
R4
R5
R6
R7
GND
R5917
XX
R5919
47k
C5919
4.7u
BL_CONT_T
BL_BRT_T
BL_CONT
BL_BRT
REGGND
1
2
10uH
L5901
CN5907 39P
EP_2.8V
PVDD(3.3V)
1
R5916 47k
3
R5920
XX
LCD901
C5903
4.7u
R5926
10k
PVDD(3.3V)
SLV18
VSS
SDI
SCK
SCS
RESB
V18OUT
VDDIO
VSYNC
HSYNC
DCLK
B0
2
D2+_T
3.2inch
WIDE
COLOR
LCD
4
D2+
N.C.
LS0
R5918
D0-_T
3
R5921
47k
XX
5
10k
D0-
R5928
4
D2-_T
D1+_T
D1-_T
D0+_T
CLK-_T
CLK+_T
D1-_T
UNIT
D2-
6
D0+
BB_SO_T
5
IC5901
SN65LVDS302ZQER
LCD DRIVE
REGGND
7
CLK-
CLK+
D1-
XSCK_T
6
D1+
N.C.
8
XCS_T
7
R0_T
R1_T
R2_T
R3_T
R4_T
R5_T
R6_T
R7_T
R5932
0
9
XBB_RST_T
8
D1+_T
D2-_T
R5925 XX
D1-
REGGND
CLK+
10
11
12
13
14
15
16
17
18
19
20
21
D1+
C5929
XX
9
D2-
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
CLK+_T
CLK-_T
D0+_T
D0-_T
D2+_T
CL5907
CL5906
D2+
L5903
10uH
VS_T
HS_T
DCLK_T
B0_T
B1_T
B2_T
B3_T
B4_T
B5_T
B6_T
B7_T
G0_T
G1_T
G2_T
G3_T
G4_T
G5_T
G6_T
G7_T
R0_T
R1_T
R2_T
R3_T
R4_T
R5_T
R6_T
R7_T
N.C.
GND
C5928
4.7u
CLK-
GND
CL5903
CL5902
CL5901
REGGND
D0+
GND
GND
B1
N.C.
GND
B2
D0-
B3
REGGND
PANEL_NOR/REV
P_BL_ON
B4
FP-807
PANEL_NOR/REV
P_BL_ON_T
TP_Y_T
FLEXIBLE
B5
B6
PAGE 4-39
of LEVEL2
TP_Y 22
C2 C4 C6 D7 E7 F7 G7 C5 C7 D3 D4 D5 D6 E3 E4 E5 E6 F3 F4 F5
B7
10uH
L5902
TP_SEL1
TP_X
TP_SEL1_T
TP_X_T
23
24
G0
G1
REGGND 25
REGGND 26
C5905
22u
6.3V
C5907
0.1u
G2
G3
27
28
29
REGGND
REGGND
G4
G5
KEY_AD0
BL_-V_T
KEY_AD0
G6
BL_-V 30
G7
EP_2.8V
31
32
33
34
35
EP_2.8V_T
R0
EP_2.8V
R1
N.C.
R2
EP_1.8V
R3
D_2.8V
D_2.8V_T
R4
XBB_RST_T
F
XBB_RST 36
R5
XSCK_T
XCS_T
XSCK
XCS
37
38
39
R6
R7
BB_SO_T
BB_SO
VSS
TCOM2
6P
6
CN5902
NC
Note: LCD901 is not included in PD-343 complete board.
EP_2.8V_T
TP_X_T
TP_TOP
TP_BOT
NC
BL_BRT_T
5
R5943
2200
R5941
2200
R5940
4700
R5939
10k
4
P_BL_ON_T
TOUCH
PANEL
2.8
3
2.8
2.7
2.2
5
2.1
2.1
1.6
5
6
4
R5938
33k
1
4
Q5909
UP04401G08S0
BACKLIGHT DRIVE
TP_Y_T
TP_L
2
Q5907
1.6
G
2.8
2.7
G
UNR31A3G0LS0
BACKLIGHT DRIVE
TP_R
1
2
2
Q5908
1 3 1.0
1.0
1.6 6 3
UP04601G08S02.2
BACKLIGHT DRIVE
0
TP_SEL1_T
D_2.8V_T
2.8
3
5
Q5901
XP411F-TXE
TOUCH PANEL I/F
2.8
BL_CONT_T
R5936
3300
D5901
XX
2.8
R5937
22k
4
1
0
6
5
4
1
2
3
6
2.8
REG_GND
6
5
4
3
2
1
BL_H
XX
R5931
NC
RB5901
100k
2
5
NC
2.8
BACKLIGHT
LED
PD-343 BOARD
XX MARK:NO MOUNT
NO MARK:REC/PB MODE
Q5902
NC
XP421F-TXE
TOUCH PANEL I/F
LCD DRIVE
0
NC
3
6
4
1
2.8
BL_L
CN5905 6P
-9.8
1.6
6
4
H
H
-9.8
5
0
Q5910
UP04601G08S0
C5902
0.0047u
2
C5901
0.0047u
2
0
BACKLIGHT DRIVE
1 3
-9.8
R5942
1k
0
R5944
15
R5946
XX
REG_GND
BL_-V_T
08
HDR-SR11/SR11E/SR12/SR12E_L2
PD-343
4-31
1
2
3
4
5
6
7
8
FB9003
12P
CN9002
SE9001
30.8kHz
SIRCS_SIG
1
2
3
4
5
6
7
8
9
SIRCS_SIG
XTALL_LED
REG_GND
REG_GND
D_2.8V
A
A
C9017
0.33u
PITCH SENSOR
XTALLY_LED
R9004
10k
C9013
22u
GND
VCC
C9005
0.1u
REG_GND
REG_GND
D_2.8V
R9013
15k
C9011
0.047u
L9001
10uH
OUT VREF
FP-812
A_2.8V
FLEXIBLE
NS_LED_A
NS_LED_K
A_2.8V
5
4
3
2
1
NS_A
C9014
4.7u
NS_K
PAGE 4-41
of LEVEL2
R9005
1M
A_2.8V
REG_GND
PITCH_AD
REG_GND
10 PITCH_AD
11 VST_C_RESET
12 YAW_AD
0
1.2
C9008
0.047u
LIA1
OUT1
NC
PITCH_AD
VST_C_RESET
YAW_AD
0
0.1u
C9003
LIB1
GND
LIB2
LIA2
RB9001
22k
IC9001
NJM3230SE7
PITCH/YAW SENSOR AMP
2.8
B
B
V+
0.6
0.8
0
CRST
OUT2
VST_C_RESET
YAW_AD
1
3
5
7
2
4
6
8
1.4
FB9001
FB9002
0.047u
C9009
C9004
0.1u
FB9004
R9006
1M
SE9002
32.2kHz
YAW SENSOR
11 12 13 14 15
D9001
CL-330IRS-X-TU
(NIGHTSHOT)
0.047u
C9010
2
1
4
R9012
15k
NS_LED_A
C9012
22u
R9007
10k
NS_LED_K
C
C
D9002
CL-196HR-CD-T
(TALLY)
C9016
0.33u
3
R9010
220
D_2.8V
C9001
0.1u
XTALLY_LED
REG_GND
R9008
0
D_2.8V
IC9002
RS-770
REMOTE COMMANDER RECEIVER
2.8
2.8
SIRCS_SIG
C9015
1u
VCC
GND
OUT
GND
D
D
REG_GND
E
E
FR-278 BOARD
PITCH/YAW SENSOR AMP,
REMOTE COMMANDER RECEIVER
XX MARK:NO MOUNT
F
NO MARK:REC/PB MODE
F
08
HDR-SR11/SR11E/SR12/SR12E_L2
FR-278
4-32
1
2
3
4
5
6
7
8
S5806
(PANEL OPEN/CLOSE)
C
1
3
2
4
PANEL_O/C
A
A
VD5801
XX
39P CN5802
CN5801
51 BL_CONT
BL_BRT
51P
1
2
BL_CONT
BL_BRT
REGGND
50
3
49 REGGND
48 D2+
4
D2+
N.C.
LND581
5
47
46
45
44
N.C.
D2-
S5801
RESET
6
CH GND
D2-
B
B
REGGND
D1+
7
REGGND
2
4
1
3
FR_XRESET
REG_GND
8
D1+
N.C.
9
43 N.C.
D1-
10
11
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
D1-
REGGND
CLK+
N.C.
REGGND
CN5803
2P
CLK+ 12
13
SP+
SP-
SP(+)
SP(-)
1
2
N.C.
SP901
(SPEAKER)
CLK-
CLK- 14
15
REGGND
D0+
REGGND
16
17
D0+
N.C.
Note: SP901 is not included in CK-185 complete board.
LND582
N.C.
D0-
CH GND
FP-807
D0- 18
FLEXIBLE
S5808
C
C
REGGND
REGGND
PAGE 4-39
of LEVEL2
19
20
21
22
8
7
6
5
NIGHTSHOT
OFF ON
R5805
1200
PANEL_NOR/REV
P_BL_ON
Nor/Rev
1 2 3 4
P_BL_ON
KEY_AD3
1005
TP_Y
TP_Y
XX
VD5808
TP_SEL1
TP_X
TP_SEL1 23
S5804
S5802
S5803
TP_X
24
25
26
27
28
29
30
31
32
FP-808
EASY
FLEXIBLE
REGGND
REGGND
REGGND
PAGE 4-41
of LEVEL2
REGGND
REGGND
REGGND
KEY_AD0
KEY_AD2
R5801
2200
R5802
1500
R5804
1200
REGGND
REGGND
1
3
2
4
1
2
4
1
2
4
KEY_AD0
BL_-V
BL_-V
3
1
3
EP_2.8V
EP_2.8V
D
D
EP_2.8V
EP_2.8V
N.C. 33
EP_1.8V 34
D_2.8V 35
N.C.
2
EP_1.8V
D_2.8V
XBATT_VIEW
3
4
S5805
DISP
36
XBB_RST
XBB_RST
LND583
/BATT INFO
37
38
39
15 XSCK
14 XCS
XSCK
XCS
CH GND
13 BB_SO
BB_SO
12
11
10
9
REGGND
REGGND
REGGND
KEY_AD3
N.C.
KEY_AD3
E
E
8
7
PANEL_O/C
FR_XRESET
KEY_AD2
XBATT_VIEW
REG_GND
SP+
PANEL_O/C
FR_XRESET
KEY_AD2
6
5
4
XBATT_VIEW
REGGND
SP+
3
CK-185 BOARD
2
CONTROL SWITCH
SP-
1
SP-
XX MARK:NO MOUNT
F
F
08
HDR-SR11/SR11E/SR12/SR12E_L2
CK-185
4-33
• Refer to page 4-2 (English), 4-3 (Japanese) for mark 0.
1
2
3
4
5
6
7
8
9
10
11
12
T5001
D5003
CRF02(TE85R)
2
1
4
3
6
C5005
220p
L5001
2.2uH
R5008
4700
A
B
C
D
A
B
C
D
CN5002
18P
XE_A
XE_A
D5002
RB520S-40TE61
18
17
16
15
14
13
12
11
10
9
C5006
70u
C5004
10u
330V
XE_A
5
CHARGING
CAPACITOR
XE_A
N.C.
N.C.
IC5001
TPS65552DGQR
FLASH CONTROL CHARGE CONTROL
ST_GND
ST_GND
FLASH UNIT
(FL25500)
LND001-LND004,
LND009, LND010,
LND023, LND024
8.3
8.3
5.1
NC
PGND
VBAT
SW
N.C.
N.C.
R5005
XX
0
CHG
VCC
8
XE_K
XE_K
0
2.8
0
XINCHG
G_IGBT
Q5001
PAGE 4-43
of LEVEL2
F_ON
I_PEAK
7
TIG030TS-S-TL-E
1.9
R5003
330k
XE_K
XE_K
SWITCH
283
6
4
3
2
1
11
5
IGBT
R5004
100k
4
N.C.
N.C.
14P CN5001
3
14
13
12
11
10
9
R5010
100
ST_UNREG
ST_UNREG
Adapter Detect
2
8
7
6
5
REG_GND(ST_GND)
C5001
XX
1
ST_UNREG
NC
0
D5001
C5002
0.1u
C5003
2.2u
R5011
1M
R5006
XX
R5007
XX
XX
CL5001
SCHARGE_ON
XSCHARGE_FULL
STROBO_ON
R5001 XX
FP-803
8
FLEXIBLE
PAGE 4-38
of LEVEL2
7
NC
MT_5V
6
ST_GND
5
ST_GND
ST_GND
4
3
ST_GND
2
Adapter Detect
1
ST-185 BOARD
R5009
XX
FLASH DRIVE
XX MARK:NO MOUNT
NO MARK:REC/PB MODE
R5002
XX
LD5001
GND
08
1
2
3
4
5
6
7
8
CN7202
5P
CN7201
20P
USB_GND
USB_GND
USB_D+
1
2
5
4
3
2
1
GND
9
8
ID
LF7201
XX
3
D+
D-
A
A
4
3
2
1
(USB)
USB_D-
4
7
6
USB_GND
5
VCC
USB_GND
USB_VCC
REG_GND
6
100
R7203
7
8
AUDIO_L_I/O
AUDIO_R_I/O
REG_GND
9
FP-804
10
11
12
13
14
15
16
17
18
19
20
FLEXIBLE
PAGE 4-38
of LEVEL2
10P
CN7203
S_Y/D3_Y
REG_GND
FB7201
AUDIO_L
LANC_SIG
S_GND
1
2
R7206
0
S_C/D3_Pb
REG_GND
B
B
12 11
3
R7202
0
LANC_DC
JACK_AD
4
R7204
0
LANC_SIG
LANC_DC
S_C/D3_Pb
AUDIO_R
5
FB7202
A/V R
6
REG_GND
MULTI_JACK_IN
VIDEO/AUDIO_GND
VIDEO/D3_Pr
7
VIDEO/D3_Pr
8
13
14
R7201
0
9
0
R7205
S_Y/D3_Y
10
LN7201
CHASSIS_GND
LN7202
CHASSIS_GND
C
C
JK-356 BOARD
JACK
XX MARK:NO MOUNT
08
HDR-SR11/SR11E/SR12/SR12E_L2
ST-185, JK-356
4-34
1
2
3
4
5
6
7
8
45P
CN7402
45
44
43
42
41
40
39
38
37
36
35
USB_VCC
A
A
DISC_BURN(KEY_AD3)
REG_GND
USB_D-
USB_D+
REG_GND
USB_D+
REG_GND(USB_GND)
USB_D-
USB_VCC
AUDIO_L
REG_GND
REG_GND
AUDIO_L_I/O
REG_GND
AUDIO_R
34 AUDIO_R_I/O
B
B
REG_GND
33
32
31
30
29
28
27
MULTI_JACK_IN
LANC_SIG
JACK_AD_CRADLE
REG_GND
LANC_SIG
REG_GND
LANC_DC
REG_GND
LANC_DC
VIDEO/D3_Pr
S_C/D3_Pb
26 VIDEO/D3_PR
25
24
23
22
REG_GND
S_C/D3_PB
REG_GND
S_Y/D3_Y
FP-806
FLEXIBLE
S_Y/D3_Y
PAGE 4-39
of LEVEL2
21 REG_GND
BATT/XEXT_CR
C
C
BATT/XEXT_CR
20
19
18
17
16
15
14
13
12
11
10
9
ACV_REG_GND
ACV_REG_GND
ACV_REG_GND
TO CRADLE
(Handycam Station)
CN7401
(MULTI CONNECTOR)
ACV_REG_GND
ACV_REG_GND
32P
ACV_REG_GND
ACV_REG_GND
USB_DET/VBUS
2
DISC_BURN(KEY_AD3)
AUDIO_L
1
3
5
7
9
USB_GND
USB_D+
4
ACV_REG_GND
ACV_REG_GND
6
(USB_ID)
AUDIO_R
REG_GND
USB_D-
8
N.C
USB_GND
10
12
14
16
18
20
N.C
LANC_SIG
AV_JACK_IN 11
D
D
ACV_UNREG
8
REG_GND
LANC_DC
REG_GND
VIDEO_I/O
REG_GND
13
15
17
ACV_UNREG
7
6
ACV_UNREG
ACV_UNREG
ACV_UNREG
REG_GND
S_Y_I/O
5
S_C_I/O 19
LN7401
GND
4
21
23
25
27
29
31
33
REG_GND
BATT/XEXT_CR
ACV_GND
ACV_UNREG
ACV_UNREG
3
2
26
28
ACV_GND
ACV_GND
1
ACV_UNREG
ACV_GND
30 N.C
32
34 ACV_UNREG
N.C
ACV_UNREG
ACV_UNREG
ACV_UNREG
E
E
CR-089 BOARD
CRADLE TERMINAL
XX MARK:NO MOUNT
F
F
08
HDR-SR11/SR11E/SR12/SR12E_L2
CR-089
4-35
• Refer to page 4-2 (English), 4-3 (Japanese) for mark 0.
1
2
3
4
1
2
3
4
Note: BT7301(lithium starage battery) is not
included in the MS-381 complete board.
D7302
C7303
A
A
BT7301
XX
A
A
XX
(LITHIUM STARAGE BATTERY)
D7303
XX
C7304
XX
CN7301
22P
D7301
CL-271HR-C-TS
(ACCESS)
XMS_ACCESS_LED
LI_3V
1
2
3
4
5
6
7
8
9
RB5701
D5701
NESW007AT-T099
(EVF BACKLIGHT)
BH7301
(BATTERY HOLDER)
ACCESS_LED_A
LI_GND
47k
1
3
5
7
2
4
6
8
18P CN5701
R7301
XX
LI_GND
R5704
XX
R5701
XX
LED_K
EP_4.6V
EVF_COM
EVF_PSIG
EVF_VG
1
2
MS_VCC
LN7301
R7302
CN5702 21P
C7302
22u
C7305
XX
REG_GND
C7301
XX
REG_GND
REG_GND
MS_SCLK
0
CN7302 10P
6.3V
3
21
20
19
18
17
16
15
14
13
12
11
10
9
EVF_COM
EVF_PSIG
EVF_VG
EVF_VR
EVF_VB
10
9
VSS
B
B
B
B
4
VCC
0
12
R7308
5
REG_GND 10
MS_DATA3 11
REG_GND 12
MS_IN 13
8
MS_SCLK
FB7301
EVF_VR
6
7
MSDATA3
XMS_IN
EVF_VB
7
R7305
180
180
6
MEMORY
STICK
PRO DUO
R7303
EVF_PCG
180
8
EVF_PCG
EVF_EN
FB7302
FB7303
FB7304
MSDATA2
5
EVF_VCK
EVF_STB
EVF_EN
9
R7306
REG_GND 14
MS_DATA2 15
REG_GND 16
MS_DATA0 17
REG_GND 18
MSDATA0
MSDATA1
MSBS
4
10
11
12
13
14
15
16
17
18
EVF_VCK
EVF_VST
EVF_STB
EVF_REF
EVF_DWN
EVF_NRW
EVF_RGT
EVF_HCK1
EVF_HCK2
EVF_HST
VSSG
R7304 180
3
11
2
EVF_VST
R7307
0
1
VSS
EVF_REF
EVF_GND
EVF_HCK1
EVF_HCK2
EVF_HST
EVF_VDD
MS_DATA1
19
REG_GND 20
MS_BS 21
LN7302
8
C
C
C
C
REG_GND
7
REG_GND 22
6
MS-381 BOARD
FP-805
5
FLEXIBLE
4
FP-811
C5702
1u
MS CONNECTOR
XX MARK:NO MOUNT
C5701
0.1u
B
R5702
XX
FLEXIBLE
3
VSS
PAGE 4-38
of LEVEL2
B
C5703
XX
08
1608
2
EVF_VDD
N.C.
PAGE 4-41
of LEVEL2
D5702
MAZS056G08S0
1
LCD902
COLOR EVF
UNIT
1
2
3
4
5
D
D
FP-454 FLEXIBLE BOARD
A
B
Note: LCD902 is not included
in BL-017 complete board.
PANEL REVERSE DETECT
NO MARK:REC/PB MODE
E
E
2.5
2.5
6 D_2.8V
5 N.C
LN7901
LN7902
LN7903
LN7904
LN7905
LN7906
IC001
5
1
4
3
PANEL REVERSE
DETECT
PD-343
PANEL_NON/REV
4
CN5909
IC001
PAGE 4-31
of LEVEL 2
AN48830B-NL
3 N.C.
2
2 REG_GND
1 REG_GND
BL-017 BOARD
EVF, EVF BACKLIGHT
C
XX MARK:NO MOUNT
F
F
08
08
HDR-SR11/SR11E/SR12/SR12E_L2
BL-017, MS-381, FP-454
4-36
1
2
3
4
LND027
GND
Pin
26
25
24
1
2
3
4
GND
GND
LND026
LND025
LND024
LND023
LND022
TMDS DATA2 +
TMDS DATA2 -
GND
CN7191 23P
A
A
1
2
3
4
5
6
7
8
9
TMDS_DATA2_SHIELD
XX
XX
XX
LF7191
LF7192
LF7193
Pin
51
50
49
Pin
1
TMDS_DATA2_+
TMDS_DATA2_-
4
3
2
1
LND052
LND053
LND054
LND055
LND056
LND057
LND058
LND059
LND060
LND061
LND062
LND063
LND064
LND065
LND066
LND067
LND068
LND069
LND070
LND071
LND072
LND073
MT_GND
LND001
LND002
LND003
LND004
LND005
LND006
LND007
GND
MT_GND
MT_GND
MT_GND
MT_GND
MT_5.0V
MT_5.0V
D_1.5V
A
A
LND021
LND020
LND019
LND018
LND017
LND016
LND015
LND014
LND013
LND012
LND011
LND010
MT_GND
MT_GND
2
TMDS DATA1 +
TMDS DATA1 -
GND
TMDS_DATA1_SHIELD
TMDS_DATA1_+
3
21 20
4
3
2
1
MT_GND
TMDS_DATA1_-
MT_5.0V
GND
TMDS_DATA0_SHIELD
TMDS_DATA0_+
MT_5.0V
TMDS DATA0 +
TMDS DATA0 -
GND
4
3
2
1
D_1.5V
TMDS_DATA0_-
HDMI
OUT
CMOS_A_3.3V
D_2.8V
CMOS_A_3.3V LND008
10 TMDS_CLOCK_SHIELD
11 TMDS_CLOCK_+
12 TMDS_CLOCK_-
13 DDC_CEC_GND
14 CEC
VC-516
LF7194 XX
D_2.8V
LND009
LND010
LND011
LND012
LND013
LND014
LND015
LND016
LND017
LND018
LND019
LND020
LND021
LND022
GND
(2/22)
4
3
2
1
B
B
CN1101
DIRA1
DIRA1
TMDS CLOCK +
TMDS CLOCK -
GND
PAGE 4-6
of LEVEL3
DIRB1
DIRB1
XCAM_SCK
CAM_S1
XCAM_SCK
CAM_S1
B
B
CEC
15 SCL
23 22
LND009
LND008
CAM_SO
CAM_SO
GND
16 SDA
REG_GND
IC_5501_CLK
REG_GND
ND_NOISE
XCS_IC_5501
IC_5501_SI
XCS_IC_5201
IC_5501_SO
REG_GND
IC_5501_CLK
REG_GND
ND_NOISE
XCS_IC_5501
IC_5501_SI
XCS_IC_5201
IC_5501_SO
LND007
LND006
17 RESERVED
18 +5V_POWER
19 HPD
SCL
SDA
+5V POWER
+5V POWER
LND005
LND004
3
2
1
LND003
HPD
LND002
LND001
GND
GND
C
C
LND074 LENS_TEMP_AD
LENS_TEMP_AD LND023
LND075
LND076
LND077
LND078
LND079
LND080
LND081
IC_5501_SCK
THERM
IC_5501_SCK
THERM
LND024
LND025
LND026
LND027
LND028
LND029
LND030
LD-230
VC-516
FP-798 FLEXIBLE BOARD
C
C
(1/4)
(2/22)
CN5102
PAGE 4-27
of LEVEL3
CN1105
PAGE 4-6
of LEVEL3
IC_5201_VD
EXT_CAM_VD
NF_EN
IC_5201_VD
EXT_CAM_VD
NF_EN
HDMI CONNECTOR
XX MARK:NO MOUNT
08
NF_SW
NF_SW
XRST_IC_5501_CPU
XRST_IC_5501_CPU
1
2
3
4
LND082 XRST_IC_5201
XRST_IC_5201 LND031
LND083
LND084
LND085
LND086
LND087
LND088
LND089
LND090
LND091
LND092
LND093
LND094
LND095
LND096
LND097
LND098
LND099
LND100
LND101
LND102
VST_C_RST
XSYS_RST
REG_GND
REG_GND
YAW_AD
REG_GND
REG_GND
PITCH_AD
EN1
VST_C_RST
XSYS_RST
REG_GND
REG_GND
YAW_AD
REG_GND
REG_GND
PITCH_AD
EN1
LND032
LND033
LND034
LND035
LND036
LND037
LND038
LND039
LND040
LND041
LND042
LND043
LND044
LND045
LND046
LND047
LND048
LND049
LND050
LND051
A
Note: J7221 and J7222 are not included in FP-799 flexible board.
A
D
D
Pin
12
11
10
J7221
LND012
LND011
LND010
LND009
HP_GND
(HEADPHONE)
HP_JACK_IN
HP_GND
REG_GND
ENO
REG_GND
ENO
1
GND
2
3
L
S
HP_L_OUT
HP_GND
DIRB0
DIRB0
LND008
VC-516
4
R
(1/22)
DIRA0
DIRA0
HP_R_OUT
LND007
LND006
CN1002
PAGE 4-5
of LEVEL3
LENS_COVER_OPEN
LENS_COVER_OPEN
HP_GND
MIC_GND
LENS_COVER_LED_ON
DIAL_B
LENS_COVER_LED_ON
DIAL_B
LND005
LND004
LND003
LND002
LND001
GND
1
2
3
L
B
B
EXT_MIC_R
MIC_GND
S
DIAL_A
3
2
1
DIAL_A
4
R
49
50
51
3
2
1
EXT_MIC_L
PON_SW
REG_GND
KEY_AD2
PON_SW
REG_GND
KEY_AD2
J7222
MIC
(PLUG IN POWER)
E
E
MIC_GND
FP-801 FLEXIBLE BOARD
LD-VC CONNECTION
(PRINTED WIRING BOARD is omitted.)
C
C
F
F
FP-799 FLEXIBLE BOARD
HP, MIC JACK
(PRINTED WIRING BOARD is omitted.)
08
08
HDR-SR11/SR11E/SR12/SR12E_L2
FP-798, FP-799, FP-801
4-37
1
2
3
4
1
2
3
4
Pin
1
Pin
REG_GND(SHOE_GND)
LND015
LND016
LND017
LND018
LND019
LND020
LND021
LND022
LND025
LND026
LND027
LND028
LND001
LND002
LND003
LND004
LND005
LND006
LND007
LND008
LND009
LND010
LND011
LND012
LND013
LND014
LND015
LND016
LND017
LND018
LND019
LND020
LND021
LND022
LND023
LND024
LND025
1
2
3
REG_GND
REG_GND
USB_D+
N.C.
2
N.C
3
LANC_SIG
EXT_STROBE
HOTSHOE_ID2
SHOE_UNREG
SHOE_UNREG
HOTSHOE_ID1
SHOE_MIC_GND
MIC_FL
A
A
A
A
VC-516
Pin
USB_D-
(1/22)
REG_GND
LND026
LND027
LND028
LND029
LND030
LND031
LND032
LND033
LND034
LND035
LND036
LND037
LND038
LND039
LND040
LND041
LND042
LND043
LND044
LND045
USB_GND
USB_GND
USB_D+
1
2
3
CN1003
PAGE 4-5
of LEVEL3
REG_GND
N.C.
USB_VCC
N.C.
USB_D-
10
11
12
USB_GND
MIC_FR
USB_GND
USB_VCC
REG_GND
REG_GND
REG_GND
VC-516
REG_GND
(2/22)
CN1106
PAGE 4-6
of LEVEL3
AUDIO_L_I/O
AUDIO_R_I/O
AUDIO_L_I/O
AUDIO_R_I/O
REG_GND
JK-356
B
B
B
B
REG_GND
REG_GND
S_Y/D3_Y
CN7201
PAGE 4-34
of LEVEL2
S_Y/D3_Y
REG_GND
REG_GND
S_C/D3_Pb
REG_GND
JACK_AD
S_C/D3_Pb
REG_GND
JACK_AD
LANC_SIG
LANC_DC
LANC_SIG
LANC_DC
REG_GND
18
19
20
23
24
25
REG_GND
HOT SHOE
VIDEO/D3_Pr
VIDEO/D3_Pr
Active
Interface Shoe
C
C
C
C
FP-804 FLEXIBLE BOARD
FP-802 FLEXIBLE BOARD
VC-JK CONNECTOR
HOT SHOE CONNECTION
(PRINTED WIRING BOARD is omitted.)
(PRINTED WIRING BOARD is omitted.)
08
08
1
2
3
4
1
2
3
4
A
A
A
A
Pin
22
21
20
Pin
1
LND001
LND002
LND003
LND004
LND005
LND006
LND007
LND008
LND009
LND010
LND011
LND012
LND013
LND014
LND015
LND016
LND017
LND018
LND019
LND020
LND021
LND022
XMS_ACCESS_LED
LI_3V
LND023
LND024
LND025
LND026
LND027
LND028
LND029
LND030
LND031
LND032
LND033
LND034
LND035
LND036
LND037
LND038
LND039
LND040
LND041
LND042
LND043
LND044
XMS_ACCESS_LED
BATT_LI_3V
2
Pin
1
Pin
14
13
12
3
ACCESS_LED_A
ACCESS_LED_A
REG_GND
ST_UNREG
ST_UNREG
ST_UNREG
ST_UNREG
ST_UNREG
ST_UNREG
LD001
LD002
LD003
LD114
LD113
LD112
REG_GND
REG_GND
2
REG_GND
MS_VCC
3
MS_VCC
N.C
SCHARGE_ON
XSCHARGE_FULL
STROBE_ON
N.C
N.C
REG_GND
REG_GND
REG_GND
SCHARGE_ON
XSCHARGE_FULL
STROBE_ON
N.C
LD005
LD006
LD007
LD110
LD109
LD108
REG_GND
MS_SCLK
REG_GND
MS_DATA3
REG_GND
XMS_IN
VC-516
ST-185
MS_SCLK
REG_GND
MS_DATA3
REG_GND
(1/22)
CN5001
CN1005
PAGE 4-5
of LEVEL3
PAGE 4-34
of LEVEL2
VC-516
B
B
B
B
(1/22)
MS-381
MT_5.0V
MT_5.0V
LD009
LD010
LD011
LD012
LD013
LD014
LD106
LD105
LD104
LD103
LD102
LD101
CN1006
PAGE 4-5
of LEVEL3
ST_GND
ST_GND
ST_GND
ST_GND
PAGE 4-36
of LEVEL2
XMS_IN
REG_GND
REG_GND
MS_DATA2
REG_GND
MS_DATA0
12
13
14
3
2
1
ST_GND
ST_GND
ST_GND
MS_DATA2
REG_GND
ST_GND
ADAPTOR-DETECT
ADAPTOR-DETECT
MS_DATA0
REG_GND
MS_DATA1
REG_GND
MS_BS
REG_GND
MS_DATA1
REG_GND
MS_BS
3
2
1
20
21
22
REG_GND
REG_GND
C
C
C
C
FP-803 FLEXIBLE BOARD
FP-805 FLEXIBLE BOARD
VC-ST CONNECTION
VC-MS CONNECTOR
(PRINTED WIRING BOARD is omitted.)
(PRINTED WIRING BOARD is omitted.)
08
08
HDR-SR11/SR11E/SR12/SR12E_L2
FP-802, FP-803, FP-804, FP-805
4-38
1
2
3
4
1
2
3
4
Pin
1
Pin
1
Pin
BL_CONT
BL_BRT
REGGND
D2+
Pin
LND001
LND002
LND003
LND004
LND005
LND006
LND007
LND008
LND009
LND010
LND011
LND012
LND013
LND014
LND015
LND016
LND017
LND018
LND019
LND020
LND021
LND022
LND023
LND024
LND025
LND026
LND027
LND028
LND029
LND030
LND031
LND032
LND033
LND034
LND035
LND036
LND037
LND038
LND039
BL_CONT
BL_BRT
REGGND
D2+
LND040
LND041
LND042
LND043
LND044
LND045
LND046
LND047
LND048
LND049
LND050
LND051
LND052
LND053
LND054
LND055
LND056
LND057
LND058
LND059
LND060
LND061
LND062
LND063
LND064
LND065
LND066
LND067
LND068
LND069
LND070
LND071
LND072
LND073
LND074
LND075
LND076
LND077
LND078
1
2
3
LND085
LND086
LND087
LND088
LND089
LND079 45
LND080 44
2
USB_VCC
DISC_BURN
REG_GND
REG_GND
USB_D+
USB_VCC
DISC_BURN
REG_GND
REG_GND
USB_D+
2
A
A
A
A
3
3
43
LND081
LND082
LND083
LND084
LND040
LND041
LND042
LND043
LND044
LND045
LND046
LND047
LND048
LND049
LND050
LND051
LND052
LND053
LND054
LND055
LND056
LND057
LND058
LND059
LND060
LND061
LND062
LND063
LND064
N.C.
D2-
N.C.
D2-
REGGND
D1+
REG_GND(USB_GND)
USB_D-
REGGND
D1+
LND090 REG_GND(USB_GND)
USB_D-
LND001
LND002
N.C.
N.C.
REG_GND
REG_GND
REG_GND
D1-
D1-
LND003
LND004
LND005
LND006
LND007
LND008
LND009
LND010
LND011
LND012
LND013
LND014
LND015
LND016
LND017
LND018
LND019
LND020
LND021
LND022
LND023
LND024
LND025
REG_GND
REGGND
CLK+
N.C.
REGGND
CLK+
N.C.
AUDIO_L_I/O
REG_GND
AUDIO_L_I/O
REG_GND
AUDIO_R_I/O
REG_GND
AUDIO_R_I/O
REG_GND
B
B
B
B
CLK-
CLK-
JACK_AD_CRADLE
JACK_AD_CRADLE
REGGND
D0+
REGGND
D0+
REG_GND
LANC_SIG
REG_GND
LANC_SIG
N.C.
D0-
N.C.
D0-
REG_GND
LANC_DC
REG_GND
LANC_DC
PD-343
CK-185
REGGND
REGGND
CN5901
CN5802
PAGE 4-31
of LEVEL3
PAGE 4-33
of LEVEL2
Nor/Rev
P_BL_ON
TP_Y
Nor/Rev
REG_GND
REG_GND
P_BL_ON
VIDEO/D3_PR
VIDEO/D3_PR
TP_Y
REG_GND
S_C/D3_PB
REG_GND
REG_GND
S_C/D3_PB
REG_GND
VC-516
TP_SEL1
TP_SEL1
(2/22)
CR-089
TP_X
TP_X
REGGND
REGGND
REGGND
REGGND
KEY_AD0
BL_-V
CN1104
CN7402
PAGE 4-6
of LEVEL3
PAGE 4-35
of LEVEL2
REGGND
REGGND
S_Y/D3_Y
REG_GND
S_Y/D3_Y
C
C
C
C
REG_GND
BATT/XEXT_CR
ACV_REG_GND
ACV_REG_GND
ACV_REG_GND
ACV_REG_GND
ACV_REG_GND
BATT/XEXT_CR
ACV_REG_GND
ACV_REG_GND
ACV_REG_GND
ACV_REG_GND
ACV_REG_GND
REGGND
REGGND
KEY_AD0
BL_-V
EP_2.8V
EP_2.8V
EP_2.8V
EP_2.8V
LND026 ACV_REG_GND
ACV_REG_GND LND065
BL_V
BL_V
EP_1.8V
D_2.8V
LND027
LND028
LND066
LND067
ACV_REG_GND
ACV_REG_GND
ACV_REG_GND
ACV_REG_GND
EP_1.8V
D_2.8V
LND029 ACV_REG_GND
ACV_REG_GND LND068
XBB_RST
XSCK
XBB_RST
XSCK
37
38
39
LND030
N.C
LND069
N.C
37
38
39
LND031
N.C
LND070
N.C
XCS
XCS
D
D
D
D
LND032
LND033
LND034
LND035
LND036
LND037
LND038
LND039
ACV_UNREG
ACV_UNREG
ACV_UNREG
ACV_UNREG
ACV_UNREG
ACV_UNREG
ACV_UNREG
ACV_UNREG
ACV_UNREG
ACV_UNREG
ACV_UNREG
ACV_UNREG
ACV_UNREG
ACV_UNREG
ACV_UNREG
ACV_UNREG
LND071
LND072
LND073
LND074
LND075
LND076
LND077
LND078
BB_SO
BB_SO
43
44
45
3
2
1
E
E
E
E
FP-806 FLEXIBLE BOARD
FP-807 FLEXIBLE BOARD
VC-CR CONNECTION
PD-CK CONNECTION
(PRINTED WIRING BOARD is omitted.)
(PRINTED WIRING BOARD is omitted.)
F
F
F
F
08
08
HDR-SR11/SR11E/SR12/SR12E_L2
FP-806, FP-807
4-39
1
2
3
4
5
6
7
8
HARD DISC DRIVE
A
A
B
B
C
C
D
D
VC-516
(2/22)
CN1103
PAGE 4-6
of LEVEL3
E
E
FP-809 FLEXIBLE BOARD
HDD CONNECTION
(PRINTED WIRING BOARD is omitted.)
F
F
08
HDR-SR11/SR11E/SR12/SR12E_L2
FP-809
4-40
1
2
3
4
1
2
3
4
A
A
Pin
18
Pin
18
A
A
EVF_VDD
LND001
LND118
EVF_VDD
EVF_HST
EVF_HCK2
EVF_HCK1
EVF_GND
EVF_REF
EVF_VST
EVF_EN
Pin
Pin
17 LND002
LND117 17
EVF_HST
EVF_HCK2
EVF_HCK1
EVF_GND
EVF_REF
EVF_VST
EVF_EN
BL_CONT
BL_BRT
REGGND
D2+
LND130
LND131
LND132
LND133
LND134
LND135
LND136
LND137
LND138
LND139
LND140
LND141
LND091
LND092
LND093
LND094
LND095
LND096
LND097
LND098
LND099
LND100
LND101
LND102
LND103
LND104
LND105
LND106
LND107
LND108
LND109
LND110
LND111
LND112
LND113
LND114
LND115
LND116
LND117
LND118
LND119
LND120
LND121
LND122
LND123
LND124
LND125
LND126
LND127
LND128
LND129
LND079
LND080
BL_CONT
BL_BRT
16
16
51
50
51
50
49
LND003
LND116
LND004
LND005
LND006
LND007
LND008
LND009
LND010
LND011
LND012
LND013
LND014
LND015
LND115
LND114
LND113
LND112
LND111
LND110
LND109
LND108
LND107
LND106
LND105
LND104
49 LND081
LND082
LND083
LND084
LND085
LND086
LND087
LND088
LND089
LND090
LND001
LND002
LND003
LND004
LND005
LND006
LND007
LND008
LND009
LND010
LND011
LND012
LND013
LND014
LND015
LND016
LND017
LND018
LND019
LND020
LND021
LND022
LND023
LND024
LND025
LND026
LND027
LND028
LND029
LND030
LND031
LND032
LND033
LND034
LND035
LND036
REGGND
D2+
N.C.
N.C.
D2-
D2-
REGGND
D1+
VC-516
BL-017
REGGND
D1+
(17/22)
EVF_STB
EVF_VCK
EVF_PCG
EVF_VB
EVF_STB
EVF_VCK
CN5701
B
B
CN3101
PAGE 4-21
of LEVEL3
PAGE 4-36
of LEVEL2
N.C.
N.C.
D1-
EVF_PCG
EVF_VB
D1-
B
B
REGGND
CLK+
N.C.
REGGND
CLK+
EVF_VR
EVF_VG
EVF_PSIG
EVF_COM
EP_4.6V
LED_K
EVF_VR
EVF_VG
EVF_PSIG
EVF_COM
EP_4.6V
LED_K
N.C.
CLK-
CLK-
LND016
LND017
LND018
LND103
LND102
LND101
3
2
1
3
2
1
REGGND
D0+
REGGND
D0+
N.C.
N.C.
D0-
D0-
REGGND
REGGND
Nor/Rev
P_BL_ON
C
C
Nor/Rev
P_BL_ON
FP-811 FLEXIBLE BOARD
TP_Y
TP_Y
TP_SEL1
TP_X
BL-VC CONNECTION
C
C
TP_SEL1
TP_X
(PRINTED WIRING BOARD is omitted.)
REGGND
REGGND
REGGND
REGGND
REGGND
REGGND
KEY_AD0
VC-516
08
(19/22)
CK-185
CN3301
PAGE 4-23
of LEVEL3
CN5801
REGGND
REGGND
KEY_AD0
BL_-V
PAGE 4-33
of LEVEL2
1
2
3
4
BL_-V
EP_2.8V
EP_2.8V
EP_2.8V
EP_2.8V
N.C.
N.C.
A
A
EP_1.8V
EP_1.8V
D_2.8V
D
D_2.8V
D
XBB_RST
XBB_RST
XSCK
XSCK
XCS
XCS
Pin
Pin
12
11
10
BB_SO
BB_SO
LND017
SIRCS_SIG
XTALLY_LED
REG_GND
LND001
LND002
LND003
LND004
LND005
LND006
LND007
LND008
LND009
LND010
LND011
LND012
SIRCS_SIG
1
2
3
REGGND
REGGND
REGGND
KEY_AD3
N.C.
REGGND
REGGND
REGGND
KEY_AD3
N.C.
LND018
LND019
LND020
LND021
LND022
LND023
LND024
LND025
LND026
LND027
LND028
XTALLY_LED
REG_GND
REG_GND
D_2.8V
REG_GND
D_2.8V
VC-516
(2/22)
FR-278
NS_LED_A
NS_LED_K
A_2.8V
NS_LED_A
NS_LED_K
A_2.8V
CN9002
B
B
CN1102
PANEL_O/C
PANEL_O/C
FR_XRESET
KEY_AD2
PAGE 4-32
of LEVEL2
PAGE 4-6
of LEVEL3
FR_XRESET
KEY_AD2
REG_GND
PITCH_AD
VST_C_RESET
YAW_AD
REG_GND
PITCH_AD
E
E
XBATT_VIEW
XBATT_VIEW
REGGND
SP+
10
11
12
3
2
1
3
2
1
LND037
LND038
LND039
3
2
1
REGGND
SP+
VST_C_RESET
YAW_AD
SP-
SP-
FP-808 FLEXIBLE BOARD
VC-CK CONNECTION
(PRINTED WIRING BOARD is omitted.)
C
C
F
F
FP-812 FLEXIBLE BOARD
VC-FR CONNECTOR
(PRINTED WIRING BOARD is omitted.)
08
08
HDR-SR11/SR11E/SR12/SR12E_L2
FP-808, FP-811, FP-812
4-41
1
2
3
4
1
2
3
4
A
A
A
A
S002
2
4
1
3
START/STOP
S004
CAM CTRL
LND027
OFF
(CHG)
Pin
(BACKLIGHT)
XPOWER_SW
LND026
LND022
LND021
LND020
LND019
LND018
LND017
LND016
LND015
LND014
LND013
LND012
LND011
LND010
LND009
LND008
LND007
LND006
LND005
LND004
LND003
LND002
REG_GND
START/STOP
XPOWER_SW
XMODE_SW
1
2
3
1
2
4
POWER
S002
3
Dial_B
Pin
ON
XMODE_SW
REG_GND(BSW)
B_SW
1
D002
S001
Dial_A
SML-D12M8WT86SM
(PHOTO)
B
LD-230
(1/4)
B
MODE
XPHOTO_LED
MODE_LED_VDD
XCAM_LED
DIAL_B
CN5104
DIAL_A
PAGE 4-27
of LEVEL3
B
D003
B
S003
XPON SW
REG_GND(RS)
SML-D12M8WT86SM
1
3
2
4
CHARGE_LED_VDD
XCHARGE_LED
ACCESS_LED_VDD
(CAM)
6
D006
D004
SML-D12V8WT86SN
(ACCESS)
SML-D12Y8WT86SP
( /CHG)
VC-516
PUSH MANUAL
(1/22)
XACCESS_LED
QUICKREC_SW
QUICKREC_LED_VDD
CN1007
PAGE 4-5
of LEVEL3
S005
2
4
1
3
QUICK ON
XQUICKREC_LED
REC_GND
PHOTO_REC
PHOTO_FREEZE
REG_GND
ZOOM_VR
D_2.8V
D005
CONTROL SWITCH BLOCK
(RS28900)
SML-D12Y8WT86SP
(QUICK ON)
C
C
S003
PHOTO
C
C
2
4
1
3
20
21
CONTROL SWITCH BLOCK(RS28900) is replaced as block,
so that PRINTED WIRING BOARD is omitted.
(PHOTO REC)
N.C.
22 LND001
REG_GND
2
4
1
3
08
S004
(PHOTO FREEZE)
1
2
3
4
3
1
2
2
4
1
3
S004
HOME
A
A
D
D
RV001
22k
(ZO0M)
W
T
2
4
2
4
1
3
1
3
S003
W
Pin
6
(ZO0M)
LND001
LND002
LND003
LND004
LND005
LND006
HOME_SW
2ND_ZOOM(W)
2ND_ZOOM(T)
2ND_S/S_SW
N.C
S002
T
PD-343
CN5903
PAGE 4-31
of LEVEL2
B
B
1
REG_GND
2
4
1
3
E
E
S001
START/STOP
CONTROL SWITCH BLOCK
(PS28100)
CONTROL SWITCH BLOCK(PS28100) is replaced as block,
so that PRINTED WIRING BOARD is omitted.
CONTROL SWITCH BLOCK
(SB28900)
C
C
F
F
CONTROL SWITCH BLOCK(SB28900) is replaced as block,
so that PRINTED WIRING BOARD is omitted.
08
08
HDR-SR11/SR11E/SR12/SR12E_L2
CONTROL SWITCH BLOCK (RS28900), CONTROL SWITCH BLOCK (SB28900),
CONTROL SWITCH BLOCK (PS28100)
4-42
• Refer to page 4-2 (English), 4-3 (Japanese) for mark 0.
1
2
3
4
S001
OFF
(ADAPTER DETECT)
A
A
Pin
1
ON
ST_GND
adapter detect
N.C.
LND023
LND024
1
3
2
4
2
N.C.
XE-K
XE-K
XE-K
XE-K
N.C.
LND001
LND002
LND003
LND004
LND050
XE_K
LND052
COMMON
ST-185
C001
CN5002
N.C.
0.033u
B
250V
B
B
PAGE 4-34
of LEVEL2
LND053
TRIGEER
ST_GND
ST_GND
N.C.
LND009
LND010
FLASH
UNIT
R001
3216
1M
N.C.
1/8W
XE-A
XE-A
XE-A
XE-A
LND014
LND015
16
LND016 17
18
XE_A
LND017
LND051
C
C
FLASH UNIT(FL25500)
FLASH UNIT(FL25500) is replaced as block,
so that PRINTED WIRING BOARD is omitted.
08
1
2
3
4
A
A
Pin
Pin
10
9
1
2
3
CHASSIS_GND
CHASSIS_GND
LND101
LND102
LND103
LND104
LND105
LND106
LND107
LND108
LND109
LND110
LND010
LND009
LND008
LND007
LND006
LND005
LND004
LND003
LND002
LND001
LENS_COVER_LED_ON
LENS_COVER_OPEN
REG_GND
LENS_COVER_LED_ON
LENS_COVER_OPEN
REG_GND
8
LD-230
(4/4)
LENS_COVER_LED_ON
LENS_COVER_CLOSE
SHUTTER_XB
LENS_COVER_LED_ON
LENS_COVER_CLOSE
SHUTTER_XB
LENS
BARRIER
CN5601
B
B
PAGE 4-30
of LEVEL 3
8
9
3
2
1
SHUTTER_A
SHUTTER_B
SHUTTER_A
SHUTTER_B
10
SHUTTER_XA
SHUTTER_XA
C
C
FP-712 FLEXIBLE BOARD
BARRIER UNIT CONNECTION
(PRINTED WIRING BOARD is omitted.)
HDR-SR11/SR11E/SR12/SR12E_L2
FLASH UNIT (FL25500), FP-712
4-43
4-3. PRINTED WIRING BOARDS
Link
PD-343 BOARD
FR-278 BOARD
CR-089 BOARD
MS-381 BOARD
CK-185 BOARD
ST-185 BOARD
JK-356 BOARD
BL-017 BOARD
FP-454 FLEXIBLE BOARD
FP-798 FLEXIBLE BOARD
COMMON NOTE FOR PRINTED WIRING BOARDS
HDR-SR11/SR11E/SR12/SR12E_L2
4-3. PRINTED WIRING BOARDS
4-3. PRINTED WIRING BOARDS
(ENGLISH)
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS
•
•
: Uses unleaded solder.
: Circuit board
: Flexible board
• Chip parts.
Transistor
Diode
C
6 5 4 4 5 6
5
4
4
5
3
3
3
1 2 3
6 5 4
Pattern from the side which enables seeing.
: pattern of the rear side
(The other layers’ patterns are not indicated)
B
E
1 2 3 3 2 1 1 2 3 3 2 1
2
1
3
2
1
4
2
1
1
2
3
2
4
3
6 5 4 4 5 6
2
1
• Through hole is omitted.
• There are a few cases that the part printed on diagram
isn’t mounted in this model.
• C: panel designation
5 4 3
4
1
1 2 3 3 2 1
3 4 5
1
2
2
2
1
3
(JAPANESE)
プリント図共通ノート
【プリント図ノート】
4
1
・
・
：無鉛半田を使用しています。
：基板
：フレキシブル配線板
見ている面側のパターン。
：裏側のパターン
（他のパターンについては表示されていません）
・スルーホールは省略。
・プリント図には，本機で使用していない部品が記載されている
場合があります。
・Cはパネル表示名称。
HDR-SR11/SR11E/SR12/SR12E_L2
4-44
Printed wiring boards of the CM-094, VC-516 and LD-230 boards are not shown.
Pages 4-45 to 4-48 are not shown.
HDR-SR11/SR11E/SR12/SR12E_L2
PD-343 (4 layers)
PD-343 BOARD (SIDE A)
: Uses unleaded solder.
R5919
R5917
R5921
R5918
R5920
R5916
IC5901
J1 H1 G1 F1 E1 D1 C1 B1 A1
J2 H2 G2 F2 E2 D2 C2 B2 A2
J3 H3 G3 F3 E3 D3
B3 A3
J4 H4 G4 F4 E4 D4 C4 B4 A4
J5 H5 G5 F5 E5 D5 C5 B5 A5
J6 H6 G6 F6 E6 D6 C6 B6 A6
J7 H7 G7 F7 E7 D7 C7 B7 A7
J8 H8 G8 F8 E8 D8 C8 B8 A8
J9 H9 G9 F9 E9 D9 C9 B9 A9
2
38
CN5901
R5929
1
39
CL5905
CL5904
D5903
D5904
CL5906
CL5907
Q5906
C
B
E
R5939
R5936
R5941
C5912
R5923
R5922
R5938
R5937
CL5903
C5917
C5919
C5930
3
1
4
6
R5931
6
1
4
3
3
4
1
6
R5925
Q5902
Q5901
R5944
R5943
CL5902
C5915
C5922
R5940
C5909
CL5901
1
6
C5903
2
2
28
38
1
6
CN5905
CN5902
CN5906
CN5907
1
39
1
29
1-874-486-
11
R5930
LND001
08
PD-343 BOARD (SIDE B)
No part is mounted and no pattern exists on the side B.
Therefore the mounting diagram for the side B is omitted.
08
1-874-486-
11
HDR-SR11/SR11E/SR12/SR12E_L2
PD-343
4-49
FR-278 (4 layers), CK-185 (2 layers)
: Uses unleaded solder.
CK-185 BOARD (SIDE A)
CK-185 BOARD (SIDE B)
NIGHTSHOT
OFF
B
ON
b
FR-278 BOARD (SIDE A)
FR-278 BOARD (SIDE B)
EASY
L9001
C9001
R9006
R9007
R9012
C9016
R9008
C9015
R9005
R9004
R9013
C9017
2
3
1
g
4
DISP/
BATT INFO
IC9002
VD5803
2
1
8
7
RB9001
3
2
4
SE9001
(PITCH SENSOR)
D9001
D9002
1
R9010
(TALLY)
C9005
FB9003
1-874-482-
11
08
(NIGHTSHOT)
1-874-482-
11
08
RESET
PANEL
OPEN/CLOSE
(
)
1-874-485-
11
08
1-874-485-
11
08
HDR-SR11/SR11E/SR12/SR12E_L2
FR-278, CK-185
4-50
ST-185 (4 layers), JK-356 (2 layers), CR-089 (2 layers)
: Uses unleaded solder.
ST-185 BOARD (SIDE A)
ST-185 BOARD (SIDE B)
C5002
R5004
R5005
C5003
4
2
6
R5001
C5001
D5001
C5006
(CHARGING CAPACITOR)
R5010
T5001
R5011
3
5
1
18
CN5002
1
C5004
L5001
14
2
R5009
11
08
1-874-687-
CN5001
13
1
11
1-874-687-
08
CR-089 BOARD (SIDE A)
CR-089 BOARD (SIDE B)
JK-356 BOARD
LN7202
35
36
CN7401
(MULTI CONNECTOR)
33
1
CN7202
(USB)
34
2
2
44
CN7402
1
45
LN7401
1-874-723-
11
1-874-723-
R7206
08
08
11
VD7203
FB7202
CN7203
A/V
R
R7204
R7205
LN7201
1-874-487-
11
08
HDR-SR11/SR11E/SR12/SR12E_L2
ST-185, JK-356, CR-089
4-51
MS-381 (2 layers)
: Uses unleaded solder.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
注意
電池の交換は，正しく行わないと破裂する恐れがあり
ます。電池を交換する場合には必ず同
じ型 名の電池
又は同等品と交換してください。
Note:
Replace the battery holder (BH7301) together
when replacing the lithium storage battery
(BT7301) on the MS-381 board. (The battery
holder removed once cannot be used again.)
When mounting these parts, mount new bat-
tery holder first and attach new lithium battery
next.
MS-381 BOARD (SIDE A)
MS-381 BOARD (SIDE B)
10
1
Note: MS-381基
板のリチウム蓄電池（BT7301）を交
換する場合はバッテリホルダ（BH7301）も同
時に新品に交換して下さい。（一度使用した
バッテリホルダは再使用できません。）
部品取り付けの際は，先にバッテリホルダを
取り付けてからリチウム電池を装着 して下さ
い。
C7305
BT7301
LITHIUM STORAGE
R7302
CN7302
(MEMORY STICK CONNECTOR)
(
)
BATTERY
BH7301
(BATTERY HOLDER)
R7301
LN7302
LN7301
12
D7301
(ACCESS)
11
A
K
1-874-483-
1-874-483-
11
11
08
08
Note: BT7301 (lithium storage battery) is not included
in the MS-381 complete board.
HDR-SR11/SR11E/SR12/SR12E_L2
MS-381
4-52
BL-017 (2 layers), FP-454 (1 layer), FP-798 (2 layers)
: Uses unleaded solder.
BL-017 BOARD
(SIDE A)
BL-017 BOARD
(SIDE B)
R5704
R5701
C5701
D5702
C5703
C5702
R5702
FP-798
FLEXIBLE BOARD
1-874-484-
1-874-484- 11
08
11
08
LND026
LND025
LND024
LND023
LND022
LND021
LND020
LND019
LND018
LND017
LND016
LND015
LND014
LND013
LND012
LND011
LND010
LND009
LND008
LND007
LND006
LND005
LND004
LND003
LND002
LND001
HDMI
OUT
08
FP-454 FLEXIBLE BOARD
1-874-797- 11
LND006
LND005
LND004
LND003
LND002
LND001
1-869-026- 21
08
HDR-SR11/SR11E/SR12/SR12E_L2
BL-017, FP-454, FP-798
4-53E
NOTE
5. REPAIR PARTS LIST
NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown.
Link
EXPLODED VIEWS
A
B
C
D
OVERALL SECTION-1
OVERALL SECTION-2
OVERALL SECTION-3
CABINET (L) SECTION-1
E
F
G
H
CABINET (L) SECTION-2
CABINET (F) SECTION
LENS BLOCK
CABINET (R) SECTION
I
J
K
PANEL BLOCK
EVF BLOCK
BT PANEL BLOCK
NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown.
ACCESSORIES
Link
ELECTRICAL PARTS LIST
J
H
A
I
E
E
G
C
C
E
D
A
I
D
A
J
E
E
E
K
I
G
BL-017 BOARD
FP-803 FLEXIBLE BOARD
FP-804 FLEXIBLE BOARD
FP-805 FLEXIBLE BOARD
FP-806 FLEXIBLE BOARD
FP-807 FLEXIBLE BOARD
FP-808 FLEXIBLE BOARD
FP-809 FLEXIBLE BOARD
FP-811 FLEXIBLE BOARD
FP-812 FLEXIBLE BOARD
FR-278 BOARD
CK-185 BOARD
CR-089 BOARD
FP-454 FLEXIBLE BOARD
FP-798 FLEXIBLE BOARD
FP-799 FLEXIBLE BOARD
FP-801 FLEXIBLE BOARD
FP-802 FLEXIBLE BOARD
JK-356 BOARD
MS-381 BOARD
PD-343 BOARD
ST-185 BOARD
HDR-SR11/SR11E/SR12/SR12E_L2
5. REPAIR PARTS LIST
5. REPAIR PARTS LIST
(ENGLISH)
NOTE:
When indicating parts by reference number,
please include the board name.
•
•
•
•
•
•
•
-XX, -X mean standardized parts, so they may have some differences from
the original one.
Items marked “*” are not stocked since they are seldom required for routine
service. Some delay should be anticipated when ordering these items.
The mechanical parts with no reference number in the exploded views are not
supplied.
Due to standardization, replacements in the parts list may be different from
the parts specified in the diagrams or the components used on the set.
CAPACITORS:
uF: µF
COILS
uH: µH
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
•
Color Indication of Appearance Parts
Example:
(SILVER) : Cabinet’s Color
(Silver) : Parts Color
RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
•
SEMICONDUCTORS
In each case, u: µ, for example:
uA...: µA... , uPA... , µPA... ,
uPB... , µPB... , uPC... , µPC... ,
uPD..., µPD...
(JAPANESE)
お願い
【使用上の注意】
図面
番号で部品を指定するときは基板名又はブロック
• ここに記載されている部品は, 補修用部品であるため, 回路図及び
セットに付いている部品と異
を併せて指定してください。
なる場合があります。
• -XX, -Xは標準化部品のため, セットに付いている部品と異なる場合
があります。
*印の部品は常備在庫しておりません。
• コンデンサの単位でuFはμFを示します。
• 抵抗の単位Ωは省略してあります。
0印の部品，または0印付の点線で囲まれた部品は，
安全性を維持するために，重 な部品です。
従って交換時は，必ず指定の部品を使用してください。
•
要
金 被：金属被膜抵抗。
サンキン：酸化金属被膜抵抗。
• インダクタの単位でuHはμHを示します。
• 半導体の名称でuA..., uPA..., uPB..., uPC..., uPD...等はそれぞれμ
A..., μPA..., μPB..., μPC..., μPD...を示します。
• 外装部品色表示
例：
(SILVER):セットの色を表す。
(Silver) : 部品の色を表す。
•
Abbreviation
AUS : Australian model
CH : Chinese model
CND : Canadian model
HK : Hong Kong model
J
: Japanese model
JE : Tourist model
KR : Korea model
NE : North European model
HDR-SR11/SR11E/SR12/SR12E_L2
5-1
5. REPAIR PARTS LIST
5-1. EXPLODED VIEWS
DISASSEMBLY
HARDWARE LIST
5-1-1. OVERALL SECTION-1
ns: not supplied
#2
5
(Note)
#2
6
7
9
#2
8
6
4
3
Overall Section-2
(See Page 5-3)
#3
#2
#2
ns
10
2
1
Note:
Note:
キャビネット(G(900))組立の交換時は1-13ページの
“キャビネット(G(900))組立の交換時の注意” を参照して
ください。
#2
#2
Refer to page 1-13 “Precuation on replacing the Cabinet
(G(900)) Assy”when changing the Cabinet (G(900)) Assy.
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
1
2
3
X-2188-804-1 CABINET (700) ASSY, BOTTOM
A-1494-362-A CR-089 BOARD, COMPLETE
2-664-982-01 SCREW, TRIPOD
7
7
8
1-797-994-21 HDD (MK6014GAL-60GB) (SR11/SR11E)
1-797-995-21 HDD (MK1214GAH-120GB) (SR12/SR12E)
1-874-808-11 FP-809 FLEXIBLE BOARD
* 4
5
3-290-644-01 FRAME, BOTTOM CABINET
(Note)
CABINET (G(900)) ASSY
* 9
2-890-813-01 SHEET (CK), SHIELD
10
1-874-805-11 FP-806 FLEXIBLE BOARD
6
6
3-294-308-01 DAMPER (1), 08STYLE (SR11/SR11E)
3-298-143-01 DAMPER (2), 08STYLE (SR12/SR12E)
#2
#3
2-635-562-31 SCREW (M1.7) (Black)
2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 (Red)
HDR-SR11/SR11E/SR12/SR12E_L2
5-2
5. REPAIR PARTS LIST
5-1-2. OVERALL SECTION-2
DISASSEMBLY
HARDWARE LIST
EVF Block
(See Page 5-11)
53
A
#2
#2
52
51
#3
#124
#2
#2
#12
A
#12
#2
#2
54
Overall Section-3
(See Page 5-4)
#2
Cabinet (R) Section
(See Page 5-9)
#2
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
51
52
52
53
53
X-2189-073-1 BASE (900) ASSY, SHOE COVER
X-2189-071-1 COVER (900S) ASSY, SHOE (SR11: J)
X-2189-072-1 COVER (900B) ASSY, SHOE (EXCEPT SR11: J)
X-2189-068-1 TOP (900S) ASSY (SR11: J)
54
54
3-292-369-01 COVER (R (900)), HINGE (SR11: J)
3-292-369-11 COVER (R (900)), HINGE (EXCEPT SR11: J)
#2
#3
#12
#124
2-635-562-31 SCREW (M1.7) (Black)
X-2189-069-1 TOP (900B2) ASSY (SR12/SR12E)
2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 (Red)
3-080-204-21 SCREW, TAPPING, P2 (Black)
2-599-475-01 SCREW (M1.7) (Silver)
53
X-2189-070-1 TOP (900B) ASSY (SR11: EXCEPT J/SR11E)
HDR-SR11/SR11E/SR12/SR12E_L2
5-3
5. REPAIR PARTS LIST
5-1-3. OVERALL SECTION-3
DISASSEMBLY
HARDWARE LIST
#124
101
102
#3
103
#3
Cabinet (L) Section-1
(See Page 5-5)
A
BT Panel Block
(See Page 5-12)
#3
#2
A
#2
104
105
Cabinet (F) Section
(See Page 5-7)
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
101
102
103
1-818-890-11 CONNECTOR, EXTERNAL (HOT SHOE)
1-874-801-11 FP-802 FLEXIBLE BOARD
3-292-296-01 FRAME (900), SHOE
#2
#3
#124
2-635-562-31 SCREW (M1.7) (Black)
2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 (Red)
2-599-475-01 SCREW (M1.7) (Silver)
104
1-874-802-11 FP-803 FLEXIBLE BOARD
* 105
3-290-652-01 RETAINER, BT HARNESS
HDR-SR11/SR11E/SR12/SR12E_L2
5-4
5. REPAIR PARTS LIST
5-1-4. CABINET (L) SECTION-1
DISASSEMBLY
HARDWARE LIST
Cabinet (L) Section-2
(See Page 5-6)
158
#2
#2
#2
154
151
#11
#3
153
159
#2
#2
VC-516
152
#3
155
157
156
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
* 151
152
3-292-179-01 HEAT SINK (B (900)), VC
3-292-178-01 FRAME (900), MAIN
155
156
3-290-676-01 SHEET (A), VC RADIATION
1-874-807-11 FP-808 FLEXIBLE BOARD
153
154
3-290-677-01 SHEET (B), VC RADIATION
A-1508-553-A VC-516 BOARD, COMPLETE (SERVICE)
(SR11/SR12)
A-1508-554-A VC-516 BOARD, COMPLETE (SERVICE)
(SR11E/SR12E)
* 157
* 158
159
3-290-678-01 LABEL, FUSE REPLACEMENT CAUTION
3-398-042-01 SHEET (AN), SHIELD
1-874-804-11 FP-805 FLEXIBLE BOARD
154
#2
2-635-562-31 SCREW (M1.7) (Black)
#3
#11
2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 (Red)
3-078-890-11 SCREW, TAPPING (Silver)
HDR-SR11/SR11E/SR12/SR12E_L2
5-5
5. REPAIR PARTS LIST
5-1-5. CABINET (L) SECTION-2
ns: not supplied
DISASSEMBLY
HARDWARE LIST
210
211
#11
209
212
213
208
214
207
#11
ns
#11
#11
#3
#3
#2
J7222
#11
206
215
J7221
216
205
204
203
#11
#3
202
201
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
201
202
203
* 204
* 205
1-874-811-11 FP-812 FLEXIBLE BOARD
212
* 213
* 214
3-290-484-01 RETAINER, GRIP BELT
3-290-485-01 FRAME, BELT
3-290-672-01 FRAME, JK
A-1508-570-A FR-278 BOARD, COMPLETE (SERVICE)
A-1494-357-A FP-798 FLEXIBLE BOARD, COMPLETE
3-292-182-01 RETAINER, JACK
3-292-181-01 FRAME (900), LF
215
216
A-1494-355-A JK-356 BOARD, COMPLETE
1-874-803-11 FP-804 FLEXIBLE BOARD
206
* 207
208
1-874-798-11 FP-799 FLEXIBLE BOARD
3-292-180-01 FRAME (F (900)), STRAP
X-2189-050-1 LF (900) ASSY, CABINET
J7221 1-569-950-41 JACK (SMALL TYPE) (HEADPHONE)
J7222 1-691-737-41 JACK (SMALL TYPE) (MIC)
209
209
3-290-483-01 CABINET (L) (EXCEPT SR11: US/SR12: US)
3-290-483-03 CABINET (L) (SR11: US/SR12: US)
#2
2-635-562-31 SCREW (M1.7) (Black)
#3
#11
2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 (Red)
3-078-890-11 SCREW, TAPPING (Silver)
210
211
2-664-928-41 BELT, GRIP
1-480-427-51 SWITCH BLOCK, CONTROL (PS28100)
HDR-SR11/SR11E/SR12/SR12E_L2
5-6
5. REPAIR PARTS LIST
5-1-6. CABINET (F) SECTION
DISASSEMBLY
HARDWARE LIST
256
Lens Block
(See Page 5-8)
MIC901
#3
255
254
258
257
(16mm × 7mm)
#11
#11
#11
#124 253
#124
258
#124
#11
252
251
259
CAUTION:For the part of 254 : TAPE (0716) (3-084-668-01), cut
NON WOVEN (T0.25) (3-076-631-01) into the desired
length and use it.
注意： 254 : TAPE (0716) (3-084-668-01) は, ヒメロン T0.25
(3-076-631-01)を切って使用してください。
Ref. No.
Part No.
Description
Ref. No.
257
Part No.
Description
251
251
252
252
253
3-292-211-01 RING (900), LENS (SR11: J)
3-292-211-11 RING (900), LENS (EXCEPT SR11: J)
X-2189-053-1 CABINET (F (900S)) ASSY (SR11: J)
X-2189-054-1 CABINET (F (900B)) ASSY (EXCEPT SR11: J)
3-292-212-01 FRAME (900), F
A-1217-971-A LENS BARRIER UNIT
258
259
3-080-272-01 TAPE (A)
1-480-432-11 SWITCH BLOCK, CONTROL (RS28900)
MIC901 1-542-711-31 MICROPHONE UNIT
254
255
256
256
CAUTION
TAPE (0716)
3-292-213-01 FRAME (900), MICROPHONE
X-2189-055-1 HOLDER (900S) ASSY, MICROPHONE (SR11: J)
X-2189-056-1 HOLDER (900B) ASSY, MICROPHONE
(EXCEPT SR11: J)
#3
#11
#124
2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 (Red)
3-078-890-11 SCREW, TAPPING (Silver)
2-599-475-01 SCREW (M1.7) (Silver)
HDR-SR11/SR11E/SR12/SR12E_L2
5-7
5. REPAIR PARTS LIST
5-1-7. LENS BLOCK
ns: not supplied
DISASSEMBLY
HARDWARE LIST
ns
312
#3
#3
#3
309
C5006
314
(including CM-094 complete board,
IC6803 and IC6804 (CMOS imager))
(Note 1)
#11
310
#3
311
313
#11
315
#12
308
304
#2
316
307
306
317
(Note 2)
305
303
318
LD-230
#3
#11
#2
302
301
#2
Note 2: ハーネス（同
軸ケーブル）の交換時は2-1ページの
Note 1: イメージャの交換時は4-3ページの“イメージャ交換時
“Note for disconnecting the harness (coaxial cable)”
を参照してください。
の注意”を必ずお読みください。
Note 2: Refer to page 2-1 “Note for disconnecting the harness
(coaxial cable)” when changing the harness (coaxial
cable).
Note 1: Be sure to read “Precuations for Replacement of Imager”
on page 4-2 when changing the imager.
• Refer to page 5-1 for mark 0.
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
301
302
303
304
305
1-874-800-11 FP-801 FLEXIBLE BOARD
3-292-207-01 CLAMP (900), HARNESS
A-1494-364-A LD-230 BOARD, COMPLETE
A-1497-729-A LSV-1270A (SERVICE)
3-292-204-01 FRAME (L (900)), LENS
314
A-1512-350-A CMOS BLOCK ASSY (1270) (including CM-094
complete board, IC6803 and IC6804 (CMOS imager))
(Note 1)
315
3-216-044-01 RUBBER (1270), SEAL
316
317
318
1-788-709-11 OPTICAL FILTER BLOCK (OFB-03-37)
1-965-256-31 HARNESS (COAXIAL CABLE) (Note 2)
3-292-205-01 FRAME (R (900)), LENS
306
0307
308
309
310
X-2189-052-1 HOLDER ASSY, ST
1-480-263-11 FLASH UNIT
3-292-208-01 GUARD (900), ST
3-292-206-01 HEAT SINK (A (900)), VC
3-290-663-01 HOLDER, CAPACITOR
0*C5006 1-114-393-11 ELECT
70uF
99%
330V
#2
2-635-562-31 SCREW (M1.7) (Black)
311
312
* 313
1-481-251-11 CORE, FERRITE
A-1494-365-A ST-185 BOARD, COMPLETE
3-292-209-01 SHEET (900), CM RADIATION
#3
#11
#12
2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 (Red)
3-078-890-11 SCREW, TAPPING (Silver)
3-080-204-21 SCREW, TAPPING, P2 (Black)
HDR-SR11/SR11E/SR12/SR12E_L2
5-8
5. REPAIR PARTS LIST
5-1-8. CABINET (R) SECTION
DISASSEMBLY
HARDWARE LIST
354
#11
SP901
#11
Panel Block
(See Page 5-10)
353
352
351
#2
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
351
352
* 353
* 354
X-2189-086-1 CABINET (R (900)) ASSY
A-1494-360-A CK-185 BOARD, COMPLETE
3-292-375-01 FRAME (900), CK
SP901 1-825-262-82 LOUD SPEAKER (1.6CM)
#2
2-635-562-31 SCREW (M1.7) (Black)
3-078-890-11 SCREW, TAPPING (Silver)
3-292-376-01 RETAINER (900), SP
#11
HDR-SR11/SR11E/SR12/SR12E_L2
5-9
5. REPAIR PARTS LIST
5-1-9. PANEL BLOCK
DISASSEMBLY
HARDWARE LIST
407
B
LCD901
#2
406
412
405
404
D
411
(Note)
410
403
402
(Note)
401
409
D
PD-343
#11
#2
A
#11
A
413
C
B
408
414
416
415
C
Note: FP-454, FP-807フレキシブル基
板取付時は「HELP16」を
Note: Be sure to read “HELP16” when you install the FP-454, FP-
807 flexible boards.
必ずお読みください。
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
401
401
402
403
404
3-292-370-01 COVER (O (900)), HINGE (SR11: J)
3-292-370-11 COVER (O (900)), HINGE (EXCEPT SR11: J)
1-471-278-11 MAGNET
A-1239-344-A FP-454 FLEXIBLE BOARD, COMPLETE (Note)
1-874-806-11 FP-807 FLEXIBLE BOARD (Note)
410
* 411
412
3-292-378-01 SHEET (P), INSULATING
3-292-374-01 RETAINER, P
1-480-358-21 BLOCK, LIGHT GUIDE PLATE (3.2)
3-292-368-01 CABINET (M (900)), P
413
* 414
415
416
3-292-373-01 PLATE (900), P GROUND
3-292-377-01 CUSHION (900), TP
1-480-458-11 SWITCH BLOCK, CONTROL (SB28900)
* 405
406
407
3-292-372-01 CLAMP, FLEXIBLE
X-2189-085-1 HINGE (Y), 08 STYLE ASSY
3-292-371-01 COVER (U (900)), HINGE
408
408
A-1527-539-A P CABINET(C (900)) SILVER (SR11: J)
X-2189-088-1 CABINET (C (900B)) ASSY, P (EXCEPT SR11: J)
LCD901 A-1363-618-A TP BLOCK ASSY (32ESHGU08)
#2
#11
2-635-562-31 SCREW (M1.7) (Black)
3-078-890-11 SCREW, TAPPING (Silver)
409
A-1494-361-A PD-343 BOARD, COMPLETE
HDR-SR11/SR11E/SR12/SR12E_L2
5-10
5. REPAIR PARTS LIST
5-1-10. EVF BLOCK
HARDWARE LIST
458
457
459
460
LCD902
456
455
454
451
453
#12
452
461
464
462
463
#12
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
451
452
* 453
* 454
* 455
A-1494-359-A BL-017 BOARD, COMPLETE
2-664-672-01 GUIDE, LAMP
2-638-819-01 CUSHION, LCD
2-638-818-01 ILLUMINATOR
2-638-816-01 PLATE (TFT), DEFLECTION
* 460
461
462
462
463
2-668-134-01 PANEL (CF), POLARIZATION
3-292-323-01 CABINET (LOWER), VF
3-292-324-01 COVER, VF BASE (SR11: J)
3-292-324-11 COVER, VF BASE (EXCEPT SR11: J)
X-2189-075-1 BASE ASSY, VF TILT
456
* 457
458
458
459
2-664-671-01 SPACER, LCD
464
1-874-810-11 FP-811 FLEXIBLE BOARD
2-699-236-01 CABINET (222), INNER
3-292-322-01 CABINET (UPPER), VF (SR11: J)
3-292-322-11 CABINET (UPPER), VF (EXCEPT SR11: J)
X-2189-076-1 EYE CUP ASSY
LCD902 8-753-241-14 LCX076AKE-1
#12 3-080-204-21 SCREW, TAPPING, P2 (Black)
HDR-SR11/SR11E/SR12/SR12E_L2
5-11
5. REPAIR PARTS LIST
5-1-11. BT PANEL BLOCK
ns: not supplied
HARDWARE LIST
506
505
(including BH901 and J901)
504
#11
501
503
ns
BH7301
(Note)
#11
MS-381
BT7301
(Note)
#12
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
502
注意
: BT7301 (LITHIUM STORAGE BATTERY)
Board on the mount position.
(See page 4-52.)
電池の交換は，正しく行わないと破裂する恐れがあり
ます。電池を交換する場合には必ず同
又は同等品と交換してください。
じ型 名の電池
Note:
Replace the battery holder (BH7301) together when re-
placing the lithium storage battery (BT7301) on the MS-
381 board. (The battery holder removed once cannot be
ノート: MS-381基
板のリチウム蓄電池（BT7301）を交換する場
合はバッテリホルダ（BH7301）も同
時に新品に交換し
て下さい。（一度使用したバッテリホルダは再使用でき
ません。）
部品取り付けの際は，先にバッテリホルダを取り付けて
からリチウム電池を装着 して下さい。
used again.)
When mounting these parts, mount new battery holder
first and attach new lithium battery next.
• Refer to page 5-1 for mark 0.
Ref. No.
Part No.
Description
Ref. No.
506
Part No.
Description
501
502
A-1494-358-A MS-381 BOARD, COMPLETE
3-290-650-01 CABINET, MS
X-2189-081-1 PANEL (900) ASSY, BT
* 503
* 504
0505
3-290-649-01 FRAME (700), BT TERMINAL
3-290-651-01 RETAINER, DCIN
1-821-575-21 DC JACK (including BH901 and J901)
0*BH7301 1-756-615-51 HOLDER, BATTERY (Note)
0BT7301 1-756-134-12 BATTERY, STORAGE, LITHIUM (Note)
#11
#12
3-078-890-11 SCREW, TAPPING (Silver)
3-080-204-21 SCREW, TAPPING, P2 (Black)
HDR-SR11/SR11E/SR12/SR12E_L2
5-12
BL-017 CK-185
5-2. ELECTRICAL PARTS LIST
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
A-1494-359-A BL-017 BOARD, COMPLETE
**********************
< CAPACITOR >
C5701 1-125-777-11 CERAMIC CHIP 0.1uF
C5702 1-165-908-11 CERAMIC CHIP 1uF
10%
10%
10V
10V
< CONNECTOR >
* CN5701 1-816-647-51 FFC/FPC CONNECTOR (LIF) 18P
* CN5702 1-817-698-81 CONNECTOR, FPC (ZIF) 21P
< DIODE >
* D5701 6-501-591-01 DIODE NESW007AT-T099 (EVF BACKLIGHT)
* D5702 6-501-955-01 DIODE MAZS056G08S0
< COMPOSITION CIRCUIT BLOCK >
* RB5701 1-234-380-21 RES, NETWORK 47K (1005X4)
************************************************************
A-1494-360-A CK-185 BOARD, COMPLETE
**********************
< CONNECTOR >
* CN5801 1-820-729-61 CONNECTOR, FPC (ZIF) 51P
* CN5802 1-816-058-61 CONNECTOR, FPC (ZIF) 39P
CN5803 1-778-506-21 PIN, CONNECTOR (PC BOARD) 2P
< RESISTOR >
R5801 1-218-957-11 RES-CHIP
R5802 1-218-955-11 RES-CHIP
R5804 1-218-954-11 RES-CHIP
R5805 1-218-954-11 RES-CHIP
2.2K
1.5K
1.2K
1.2K
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
< SWITCH >
S5801 1-771-138-21 SWITCH, KEY BOARD (RESET)
S5802 1-771-138-21 SWITCH, KEY BOARD (EASY)
S5803 1-771-138-21 SWITCH, KEY BOARD (DISC BURN)
S5804 1-771-138-21 SWITCH, KEY BOARD (PLAY)
S5805 1-771-138-21 SWITCH, KEY BOARD (DISP/BATT INFO)
S5806 1-786-148-11 SWITCH, PUSH (1 KEY) (PANEL OPEN/CLOSE)
S5808 1-771-731-11 SWITCH, SLIDE (NIGHTSHOT)
************************************************************
Electrical parts list of the CM-094 is not
shown.
Pages 5-14 is not shown.
HDR-SR11/SR11E/SR12/SR12E_L2
5-13
CR-089 FP-454 FP-798 FP-799 FP-801 FP-802 FP-803
FP-804 FP-805 FP-806 FP-807 FP-808 FP-809
FP-811 FP-812 FR-278
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
A-1494-362-A CR-089 BOARD, COMPLETE
1-874-806-11 FP-807 FLEXIBLE BOARD
**********************
********************
(There isn’t mounted electrical parts in FP-807 flexible board.)
< CONNECTOR >
************************************************************
* CN7401 1-821-664-21 CONNECTOR, MULTIPLE (PLUG) 32P
(MULTI CONNECTOR)
1-874-807-11 FP-808 FLEXIBLE BOARD
********************
* CN7402 1-821-202-71 CONNECTOR, FPC (ZIF) 45P
************************************************************
(There isn’t mounted electrical parts in FP-808 flexible board.)
************************************************************
A-1239-344-A FP-454 FLEXIBLE BOARD, COMPLETE
1-874-808-11 FP-809 FLEXIBLE BOARD
********************
******************************
(There isn’t mounted electrical parts in FP-809 flexible board.)
************************************************************
< IC >
IC001
6-705-011-01 IC AN48830B-NL
1-874-810-11 FP-811 FLEXIBLE BOARD
********************
************************************************************
(There isn’t mounted electrical parts in FP-811 flexible board.)
************************************************************
A-1494-357-A FP-798 FLEXIBLE BOARD, COMPLETE
******************************
1-874-811-11 FP-812 FLEXIBLE BOARD
********************
< CONNECTOR >
(There isn’t mounted electrical parts in FP-812 flexible board.)
************************************************************
CN7191 1-821-166-21 CONNECTOR, HDMI (HDMI OUT)
************************************************************
A-1508-570-A FR-278 BOARD, COMPLETE (SERVICE)
1-874-798-11 FP-799 FLEXIBLE BOARD
********************
*******************************
(J7221 and J7222 are not included in FP-799 flexible board.)
< CAPACITOR >
< JACK >
C9001 1-125-777-11 CERAMIC CHIP 0.1uF
C9003 1-125-777-11 CERAMIC CHIP 0.1uF
C9004 1-125-777-11 CERAMIC CHIP 0.1uF
C9005 1-125-777-11 CERAMIC CHIP 0.1uF
10%
10%
10%
10%
10V
10V
10V
10V
10V
J7221 1-569-950-41 JACK (SMALL TYPE) (HEADPHONE)
J7222 1-691-737-41 JACK (SMALL TYPE) (MIC)
************************************************************
C9008 1-119-923-11 CERAMIC CHIP 0.047uF 10%
1-874-800-11 FP-801 FLEXIBLE BOARD
********************
(There isn’t mounted electrical parts in FP-801 flexible board.)
************************************************************
C9009 1-119-923-11 CERAMIC CHIP 0.047uF 10%
C9010 1-119-923-11 CERAMIC CHIP 0.047uF 10%
C9011 1-119-923-11 CERAMIC CHIP 0.047uF 10%
10V
10V
10V
6.3V
6.3V
C9012 1-100-611-91 CERAMIC CHIP 22uF
20%
C9013 1-100-611-91 CERAMIC CHIP 22uF
20%
1-874-801-11 FP-802 FLEXIBLE BOARD
********************
(There isn’t mounted electrical parts in FP-802 flexible board.)
************************************************************
C9014 1-127-760-11 CERAMIC CHIP 4.7uF
C9015 1-165-908-11 CERAMIC CHIP 1uF
C9016 1-114-411-21 CERAMIC CHIP 0.33uF
C9017 1-114-411-21 CERAMIC CHIP 0.33uF
10%
10%
10%
10%
6.3V
10V
6.3V
6.3V
1-874-802-11 FP-803 FLEXIBLE BOARD
********************
< CONNECTOR >
(There isn’t mounted electrical parts in FP-803 flexible board.)
************************************************************
* CN9002 1-816-644-51 FFC/FPC CONNECTOR (LIF) 12P
1-874-803-11 FP-804 FLEXIBLE BOARD
********************
< DIODE >
(There isn’t mounted electrical parts in FP-804 flexible board.)
************************************************************
D9001 6-500-512-01 DIODE CL-330IRS-X-TU (NIGHTSHOT)
D9002 8-719-077-09 DIODE CL-196HR-CD-T (TALLY)
1-874-804-11 FP-805 FLEXIBLE BOARD
********************
< FERRITE BEAD >
(There isn’t mounted electrical parts in FP-805 flexible board.)
************************************************************
FB9001 1-400-833-21 SMD EMI FERRITE
FB9002 1-400-833-21 SMD EMI FERRITE
FB9003 1-400-833-21 SMD EMI FERRITE
FB9004 1-400-833-21 SMD EMI FERRITE
1-874-805-11 FP-806 FLEXIBLE BOARD
********************
(There isn’t mounted electrical parts in FP-806 flexible board.)
************************************************************
< IC >
IC9001 6-707-333-01 IC NJM3230SE7
IC9002 6-600-163-01 IC RS-770
HDR-SR11/SR11E/SR12/SR12E_L2
5-15
FR-278 JK-356
Ref. No.
Part No.
Description
< COIL >
Ref. No.
Part No.
Description
L9001 1-400-588-11 INDUCTOR
< RESISTOR >
10uH
R9004 1-218-965-11 RES-CHIP
R9005 1-218-989-11 RES-CHIP
R9006 1-218-989-11 RES-CHIP
R9007 1-218-965-11 RES-CHIP
R9008 1-218-990-11 SHORT CHIP
10K
1M
1M
10K
0
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
R9010 1-218-945-11 RES-CHIP
R9012 1-208-711-11 METAL CHIP
R9013 1-208-711-11 METAL CHIP
220
15K
15K
5%
1/16W
0.5% 1/16W
0.5% 1/16W
< COMPOSITION CIRCUIT BLOCK >
* RB9001 1-234-379-21 RES, NETWORK 22K (1005X4)
< SENSOR >
* SE9001 1-479-022-51 SENSOR, ANGULAR VELOCITY (PITCH)
* SE9002 1-479-022-61 SENSOR, ANGULAR VELOCITY (YAW)
************************************************************
A-1494-355-A JK-356 BOARD, COMPLETE
**********************
< CONNECTOR >
* CN7201 1-816-648-51 FFC/FPC CONNECTOR (LIF) 20P
CN7202 1-819-436-11 CONNECTOR (SQUARE TYPE) (USB) 5P (USB)
CN7203 1-815-794-13 CONNECTOR (MULTIPLE) (A/V R)
< FERRITE BEAD >
FB7201 1-500-238-11 BEAD, FERRITE (CHIP) (1608)
FB7202 1-500-238-11 BEAD, FERRITE (CHIP) (1608)
< RESISTOR >
R7201 1-216-864-11 SHORT CHIP
R7202 1-216-864-11 SHORT CHIP
R7203 1-216-809-11 METAL CHIP
R7204 1-218-990-11 SHORT CHIP
R7205 1-218-990-11 SHORT CHIP
0
0
100
0
0
5%
1/10W
R7206 1-218-990-11 SHORT CHIP
< VARISTOR >
0
* VD7201 1-802-279-11 VARISTOR (SMD)
* VD7202 1-802-279-11 VARISTOR (SMD)
* VD7203 1-802-279-11 VARISTOR (SMD)
* VD7204 1-802-279-11 VARISTOR (SMD)
* VD7205 1-802-279-11 VARISTOR (SMD)
************************************************************
Electrical parts list of the LD-230 is not
shown.
Pages 5-17 to 5-18 are not shown.
HDR-SR11/SR11E/SR12/SR12E_L2
5-16
MS-381 PD-343
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
A-1494-358-A MS-381 BOARD, COMPLETE
A-1494-361-A PD-343 BOARD, COMPLETE
***********************
**********************
(BT7301 (lithium storage battery) is not included in MS-381 complete board.)
< BATTERY HOLDER >
< CAPACITOR >
C5901 1-100-581-81 CERAMIC CHIP 0.0047uF 10%
C5902 1-100-581-81 CERAMIC CHIP 0.0047uF 10%
50V
50V
10V
6.3V
10V
0*BH7301 1-756-615-51 HOLDER, BATTERY (Note)
< BATTERY >
C5903 1-112-300-91 CERAMIC CHIP 4.7uF
C5905 1-100-786-91 TANTAL. CHIP 22uF
10%
20%
10%
C5907 1-125-777-11 CERAMIC CHIP 0.1uF
0BT7301 1-756-134-12 BATTERY, STORAGE, LITHIUM (Note)
< CAPACITOR >
C5909 1-165-875-11 CERAMIC CHIP 10uF
C5912 1-125-777-11 CERAMIC CHIP 0.1uF
C5913 1-112-300-91 CERAMIC CHIP 4.7uF
C5914 1-165-884-91 CERAMIC CHIP 2.2uF
C5915 1-127-861-11 CERAMIC CHIP 2.2uF
10%
10%
10%
10%
10%
10V
10V
10V
6.3V
16V
C7302 1-100-786-91 TANTAL. CHIP
< CONNECTOR >
22uF
20%
6.3V
C5917 1-165-884-91 CERAMIC CHIP 2.2uF
C5918 1-112-300-91 CERAMIC CHIP 4.7uF
C5919 1-112-300-91 CERAMIC CHIP 4.7uF
C5920 1-165-908-11 CERAMIC CHIP 1uF
C5921 1-165-908-11 CERAMIC CHIP 1uF
10%
10%
10%
10%
10%
6.3V
10V
10V
10V
10V
* CN7301 1-779-335-51 CONNECTOR, FFC/FPC 22P
* CN7302 1-819-990-21 MEMORY STICK DUO CONNECTOR 10P
(PRO DUO)
< DIODE >
D7301 6-501-216-01 DIODE CL-271HR-C-TS (ACCESS)
< FERRITE BEAD >
C5922 1-127-861-11 CERAMIC CHIP 2.2uF
C5923 1-165-884-91 CERAMIC CHIP 2.2uF
C5924 1-165-884-91 CERAMIC CHIP 2.2uF
C5925 1-165-884-91 CERAMIC CHIP 2.2uF
C5926 1-165-884-91 CERAMIC CHIP 2.2uF
10%
10%
10%
10%
10%
16V
6.3V
6.3V
6.3V
6.3V
FB7301 1-469-580-21 INDUCTOR, FERRITE BEAD (1005)
FB7302 1-469-580-21 INDUCTOR, FERRITE BEAD (1005)
FB7303 1-469-580-21 INDUCTOR, FERRITE BEAD (1005)
FB7304 1-469-580-21 INDUCTOR, FERRITE BEAD (1005)
C5927 1-165-884-91 CERAMIC CHIP 2.2uF
* C5928 1-112-746-11 CERAMIC CHIP 4.7uF
C5930 1-125-889-11 CERAMIC CHIP 2.2uF
10%
10%
10%
6.3V
6.3V
10V
< RESISTOR >
< CONNECTOR >
R7302 1-218-990-11 SHORT CHIP
R7303 1-218-944-11 RES-CHIP
R7304 1-218-944-11 RES-CHIP
R7305 1-218-944-11 RES-CHIP
R7306 1-218-944-11 RES-CHIP
0
* CN5901 1-817-544-71 CONNECTOR, FPC (ZIF) 39P
* CN5902 1-794-322-51 CONNECTOR, FPC (ZIF) 6P
CN5903 1-816-180-71 CONNECTOR, FPC (ZIF) 6P
* CN5905 1-794-322-51 CONNECTOR, FPC (ZIF) 6P
* CN5906 1-819-914-71 CONNECTOR, FPC (ZIF) 29P
180
180
180
180
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
R7307 1-218-990-11 SHORT CHIP
R7308 1-218-990-11 SHORT CHIP
0
0
* CN5907 1-817-544-71 CONNECTOR, FPC (ZIF) 39P
* CN5909 1-816-654-51 FFC/FPC CONNECTOR (LIF) 6P
************************************************************
< DIODE >
CAUTION
D5903 6-500-813-01 DIODE MA2SD32008S0
D5904 6-500-813-01 DIODE MA2SD32008S0
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
< IC >
注意
電池の交換は，正しく行わないと破裂する恐れがあり
* IC5901 6-712-051-01 IC SN65LVDS302ZQER
ます。電池を交換する場合には必ず同
じ型 名の電池
又は同等品と交換してください。
< COIL >
Note:
Replace the battery holder (BH7301) together when re-
placing the lithium storage battery (BT7301) on the MS-
381 board. (The battery holder removed once cannot be
used again.)
When mounting these parts, mount new battery holder
first and attach new lithium battery next.
L5901 1-400-588-11 INDUCTOR
L5902 1-400-588-11 INDUCTOR
L5903 1-400-588-11 INDUCTOR
10uH
10uH
10uH
< TRANSISTOR >
ノート: MS-381基
板のリチウム蓄電池（BT7301）を交換する場
Q5901 8-729-427-37 TRANSISTOR
XP411F-TXE
XP421F-TXE
UNR31A3G0LS0
2SK3235
合はバッテリホルダ（BH7301）も同
時に新品に交換し
て下さい。（一度使用したバッテリホルダは再使用でき
ません。）
Q5902 8-729-427-67 TRANSISTOR
* Q5907 6-551-760-01 TRANSISTOR
Q5908 8-729-053-48 TRANSISTOR
* Q5909 6-551-846-01 TRANSISTOR
部品取り付けの際は，先にバッテリホルダを取り付けて
からリチウム電池を装着 して下さい。
UP04401G08S0
Q5910 8-729-053-48 TRANSISTOR
2SK3235
• Refer to page 5-1 for mark 0.
HDR-SR11/SR11E/SR12/SR12E_L2
5-19
PD-343 ST-185
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
< RESISTOR >
< RESISTOR >
R5901 1-218-957-11 RES-CHIP
R5902 1-218-955-11 RES-CHIP
R5903 1-218-954-11 RES-CHIP
R5909 1-218-973-11 RES-CHIP
R5913 1-218-973-11 RES-CHIP
2.2K
1.5K
1.2K
47K
47K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R5003 1-208-947-11 METAL CHIP
R5004 1-208-935-11 METAL CHIP
R5008 1-216-065-91 RES-CHIP
R5010 1-216-809-11 METAL CHIP
R5011 1-218-989-11 RES-CHIP
330K
100K
4.7K
100
0.5% 1/16W
0.5% 1/16W
5%
5%
5%
1/10W
1/10W
1/16W
1M
R5914 1-218-973-11 RES-CHIP
R5916 1-218-973-11 RES-CHIP
R5919 1-218-973-11 RES-CHIP
R5921 1-218-973-11 RES-CHIP
R5923 1-218-965-11 RES-CHIP
47K
47K
47K
47K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
< TRANSFORMER >
1-443-568-31 TRANSFORMER, D.C.-D.C.CONVERTER
0
T5001
************************************************************
Electrical parts list of the VC-516 is not
shown.
Pages 5-21 to 5-28 are not shown.
R5926 1-216-833-11 METAL CHIP
R5928 1-218-965-11 RES-CHIP
R5929 1-218-990-11 SHORT CHIP
R5932 1-218-990-11 SHORT CHIP
R5936 1-208-695-11 METAL CHIP
10K
10K
0
0
3.3K
5%
5%
1/10W
1/16W
0.5% 1/16W
5% 1/16W
0.5% 1/16W
0.5% 1/16W
0.5% 1/16W
0.5% 1/16W
R5937 1-218-969-11 RES-CHIP
R5938 1-208-923-11 METAL CHIP
R5939 1-208-911-11 METAL CHIP
R5940 1-208-699-11 METAL CHIP
R5941 1-208-691-11 METAL CHIP
22K
33K
10K
4.7K
2.2K
R5942 1-208-683-11 METAL CHIP
R5943 1-208-691-11 METAL CHIP
R5944 1-211-973-11 METAL CHIP
1K
2.2K
15
0.5% 1/16W
0.5% 1/16W
0.5% 1/10W
< COMPOSITION CIRCUIT BLOCK >
RB5901 1-234-381-11 RES, NETWORK 100K (1005X4)
************************************************************
A-1494-365-A ST-185 BOARD, COMPLETE
**********************
< CAPACITOR >
C5002 1-125-777-11 CERAMIC CHIP 0.1uF
C5003 1-165-884-91 CERAMIC CHIP 2.2uF
C5004 1-165-875-11 CERAMIC CHIP 10uF
C5005 1-163-001-11 CERAMIC CHIP 220PF
10%
10%
10%
10%
99%
10V
6.3V
10V
50V
330V
0*C5006 1-114-393-11 ELECT
< CONNECTOR >
* CN5001 1-779-331-51 CONNECTOR, FFC/FPC 14P
70uF
* CN5002 1-816-647-51 FFC/FPC CONNECTOR (LIF) 18P
< DIODE >
D5002 6-500-619-01 DIODE RB520S-40TE61
0D5003 6-501-096-01 DIODE CRF02 (TE85R)
< IC >
0IC5001 6-707-554-01 IC TPS65552DGQR
< COIL >
L5001 1-412-027-11 INDUCTOR
< TRANSISTOR >
2.2uH
*0Q5001 6-551-686-01 TRANSISTOR
TIG030TS-S-TL-E
• Refer to page 5-1 for mark 0.
HDR-SR11/SR11E/SR12/SR12E_L2
5-20
• EXCEPT J MODEL
Checking supplied accessories.
to J MODEL
Power cord (Mains lead)
Operating Guide
(HDR-SR11/SR12)
3-286-585-11 (ENGLISH, SPANISH) (US, CND, JE, E:NTSC)
3-286-585-21 (FRENCH) (CND)
3-286-585-31 (PORTUGUESE) (JE)
3-286-585-41 (TRADITIONAL CHINESE) (E:NTSC)
3-286-585-51 (KOREAN) (KR, JE)
AC Adaptor
0 1-555-074-91 (AUS)
0 1-790-107-61 (US, CND)
0 1-792-549-41 (JE)
0 1-824-910-71 (AEP, NE, E:PAL)
0 1-827-269-12 (UK, HK)
0 1-832-121-31 (CH)
(AC-L200/L200B)
* Compatible in
L200 and L200B.
0 1-479-285-21
0 1-833-892-21 (KR)
0 1-834-852-11 (E:NTSC)
Operating Guide
(HDR-SR11E/SR12E)
3-286-586-11 (ENGLISH) (AEP, UK, HK, AUS, JE, E:PAL)
3-286-586-21 (FRENCH, DUTCH, GREEK) (AEP)
3-286-586-31 (GERMAN, ITALIAN, TURKISH) (AEP)
3-286-586-41 (SPANISH, PORTUGUESE, POLISH) (AEP)
3-286-586-51 (CZECH, HUNGARIAN, SLOVAK) (AEP)
3-286-586-61 (RUSSIAN, UKRAINIAN) (NE, JE)
3-286-586-71 (SWEDISH, DANISH, FINNISH) (NE)
3-286-586-81 (SIMPLIFIED CHINESE) (CH, JE, E:PAL)
3-286-586-91 (ARABIC, PERSIAN) (E:PAL)
3-286-587-41 (TRADITIONAL CHINESE) (HK)
Conversion (2P) Adaptor
0 1-569-007-12 (E:NTSC, JE)
21-Pin Adaptor
1-770-783-21 (AEP, UK, NE)
Component A/V cable
1-834-647-11
A/V connecting cable
1-823-156-51
USB cable
1-829-868-31
DVD-ROM
“ENJOY HANDYCAM”
3-282-264-01 (KR)
ENGLISH/KOREA/JAPANESE
3-282-264-11 (US, CND)
ENGLISH/FRENCH/SPANISH/PORTUGUESE
3-282-264-21 (UK, NE)
ENGLISH/RUSSIAN/GERMAN/TURKISH
3-282-264-51 (AEP)
Wireless Remote Commander
(RMT-835)
1-479-275-41
Rechargeable battery pack
(NP-FH60)
ENGLISH / FRENCH / GERMAN / DUTCH / SPANISH
/ PORTUGUESE / ITALIAN / TURKISH
3-282-264-61 (HK, AUS, CH, E)
ENGLISH / FRENCH / SIMPLIFIED CHINESE / TRADITIONAL CHINESE
3-282-264-71 (E)
0 A-1201-666-A (US, CND)
0 A-1201-667-A
(EXCEPT US, CND, CH)
0 A-1201-668-A (CH)
Handycam Station
(DCRA-C210)
1-821-692-11
ENGLISH / TRADITIONAL CHINESE / SPANISH / PORTUGUESE
The CD-ROM supplied contains all of language version of
the Instruction Manual in pdf (Handycam Handbook.pdf) for printing.
The printed matter is not supplied. If required,
please order it with the part number below.
(Only for destination Japanese model)
日本国内については日本語のみが印刷での部品供給可能です。
Handycam Handbook (PDF)
HDR-SR11/SR12
HDR-SR11E/SR12E
* 3-286-589-01 (JAPANESE)
* 3-286-589-11 (ENGLISH)
* 3-286-589-21 (FRENCH)
* 3-286-589-31 (SPANISH)
* 3-286-589-41 (PORTUGUESE)
* 3-286-589-51 (TRADITIONAL CHINESE)
* 3-286-589-61 (KOREAN)
* 3-286-590-11 (ENGLISH)
* 3-286-590-21 (FRENCH)
* 3-286-590-31 (DUTCH)
* 3-286-590-41 (GREEK)
* 3-286-590-51 (GERMAN)
* 3-286-590-61 (ITALIAN)
* 3-286-590-71 (TURKISH)
* 3-286-590-81 (SPANISH)
* 3-286-590-91 (PORTUGUESE)
* 3-286-591-11 (POLISH)
* 3-286-591-21 (CZECH)
* 3-286-591-31 (HUNGARIAN)
* 3-286-591-41 (SLOVAK)
* 3-286-591-51 (RUSSIAN)
* 3-286-591-61 (UKRAINIAN)
* 3-286-591-71 (SWEDISH)
* 3-286-591-81 (DANISH)
* 3-286-591-91 (FINNISH)
* 3-286-592-11 (SIMPLIFIED
CD-ROM "Handycam
Application Software"
Picture Motion Browser
(Software)
CHINESE)
* 3-286-592-21 (ARABIC)
* 3-286-592-31 (PERSIAN)
* 3-286-592-41 (MALAY)
* 3-286-592-51 (THAI)
* 3-286-592-61 (INDONESIAN)
* 3-286-592-71 (TRADITIONAL
PMB Guide
Handycam Handbook
3-286-588-01
CHINESE)
• Refer to page 5-1 for mark 0.
HDR-SR11/SR11E/SR12/SR12E_L2
5-29
• J MODEL
付属品
ACアダプター
電源コード
0 1-792-549-41
取扱説明書
3-286-585-01 (日本語)
(AC-L200/L200B)
* L200とL200Bには
ꢀ互換性があります。
0 1-479-285-21
DVD-ROM
“エンジョイハンディーカム”
3-282-264-01
英語/韓国語/日本語
ハンディカムステーション
(DCRA-C210)
1-821-692-11
D端子A/Vケーブル
1-834-646-21
A/V接続ケーブル
1-823-156-51
ワイヤレスリモコン
(RMT-835)
1-479-275-41
USBケーブル
1-829-868-31
リチャージャブルバッテリーパック
(NP-FH60)
0 A-1201-665-A
ハンディカムꢀハンドブック (PDF)
印刷用の取扱説明書.pdf(ハンディカム ハンドブック.pdf)は
全ての言語が付属品のCD-ROMに含まれています。
印刷物は付属されておりません。
必要
な場合は下記部品番号にて注文となります。
CD-ROM「Handycam
Application Software」
「Picture Motion Browser」
(ソフトウェア)
* 3-286-589-01ꢀ(日本語)
「PMB ガイド」
「ハンディカムꢀハンドブック」
3-286-588-01
• 0マークについては，5-1ページを参照して下さい。
HDR-SR11/SR11E/SR12/SR12E_L2
5-30E
HARDWARE LIST (1/7)
#1: M1.7 X 2.5
(Black)
#2: M1.7 X 4.0
#3: M1.7 X 2.5
(Red)
#4: M1.4 X 2.5 (Tapping)
(Dark Silver)
(Black)
2-635-562-11
2-635-562-31
2-660-401-01
3-348-998-81
1.7
1.7
1.7
1.7
1.7
1.4
2.5
4.0
2.5
2.5
#5: M1.7 X 3.5 (Tapping)
(Black)
#6: M1.4 X 1.7
(Silver)
#7: M1.7 X 1.6
(Black)
#8: M1.7 X 3.5 (Tapping)
(Silver)
3-080-204-01
2-598-474-01
7-627-552-18
3-078-890-01
1.7
1.4
1.7
3.5
3.5
1.7
1.6
#9: M1.7 X 5.0 (Tapping)
(Silver)
#10: M1.7 X 4.0
(Silver)
#11: M1.7 X 4.0 (Tapping)
(Silver)
#12: M1.7 X 5.0 (Tapping)
(Black)
3-078-890-21
2-599-475-31
3-078-890-11
3-080-204-21
1.7
1.7
1.7
1.4
1.4
4.0
5.0
4.0
5.0
#13: M1.7 X 2.5 (Tapping)
(Silver)
#14: M1.7 X 2.5
(Silver)
#15: M1.4 X 1.5
(Silver)
#16: M1.4 X 2.5
(Silver)
3-085-397-01
2-599-475-11
3-062-214-01
2-586-337-01
1.7
1.7
1.4
2.5
1.5
2.5
2.5
#17: M1.7 X 1.5
(Silver)
#18: M1.4 X 2.5
(Silver)
#19: M1.2 X 4.0 (Tapping)
(Red)
#20: M1.4 X 3.0
(Silver)
2-586-389-01
2-635-591-21
3-086-156-21
2-635-591-31
1.7 2.2
1.4
1.2
1.5
3.5
4.0
2.5
3.0
HARDWARE LIST (2/7)
#21: M1.4 X 3.0
(Black)
#22: M1.7 X 5.0 (Tapping)
#23: M1.7 X 4.0 (Tapping)
#24: B1.7 X 5.5 (Tapping)
(Black)
(Silver)
(Black)
2-662-396-21
3-083-261-01
3-080-204-11
4-679-805-11
1.7
1.4
1.2
1.7
1.7
1.4
2.0
3.0
1.4
1.7
1.4
5.0
4.0
5.5
3.0
#25: M1.7 X 3.0
(Black)
#26: M1.4 X 2.0
(Silver)
#27: M1.4 X 2.0
(Black)
#28: M1.4 X 4.0 (Tapping)
(Silver)
2-635-562-21
2-635-591-11
2-662-396-11
3-348-998-61
1.4
3.0
4.0
2.0
2.0
#29: M1.4 X 2.5
(Black)
#30: M1.2 X 4.0 (Tapping)
(White)
#31: M3.0 X 4.0
(Silver)
#32: M2.0 X 4.5 (Tapping)
(Silver)
2-662-396-01
3-086-156-11
2-102-434-01
2-102-498-01
3.0
3.5
4.0
4.5
2.5
#33: M3.0 X 6.0
(Silver)
#34: M3.0 X 8.0
(Black)
#35: M4.0 X 6.0 (Tapping)
(Silver)
#36: M3.0 X 6.0
(Silver)
3-077-331-21
3-077-331-41
3-975-291-02
4-886-821-11
3.0
3.0
4.0
6.0
8.0
6.0
6.0
#37: M2.0 X 6.0 (Tapping)
(Black)
#38: M3.0 X 20.0 (Tapping)
(Silver)
#39: M2.6 X 5.0 (Tapping)
(Black)
#40: M2.0 X 4.0 (Tapping)
(Silver)
3-080-206-31
7-685-651-79
7-685-791-09
7-685-851-04
3.0
2.0
2.6
2.0
20.0
4.0
6.0
5.0
HARDWARE LIST (3/7)
#41: M3.0 X 8.0 (Tapping)
(Silver)
#42: M2.0 X 4.0 (Tapping)
#43: M1.7 X 4.0
(Red)
#44: M1.7 X 3.0 (Tapping)
(Silver)
(Silver)
3-065-748-01
7-628-253-00
2-660-401-31
3-078-890-61
3.0
1.4
2.0
2.0
1.7
1.7
8.0
4.0
3.0
4.0
#45: M1.4 X 2.5
(Silver)
#46: M1.7 X 3.0
(Red)
#47: M1.4 X 3.0 (Tapping)
(Silver)
#48: M1.7 X 2.5
(Silver)
2-587-151-01
2-660-401-11
2-665-774-01
3-973-497-91
1.7
1.4
1.7
3.0
3.0
2.5
2.5
#49: M2.0 X 4.0
(Black)
#50: M2.0 X 3.0
(Red)
#51: M2.0 X 2.5
(Silver)
#52: M2.0 X 4.0 (Tapping)
(Black)
2-630-005-31
2-891-494-11
3-073-686-01
3-080-206-11
2.0
2.0
2.0
4.0
4.0
3.0
2.5
#53: M2.0 X 5.0 (Tapping)
(Black)
#54: M1.75 X 6.0 (Tapping)
(Black)
#55: M2.0 X 4.0
(Silver)
#56: M2.0 X 3.5
(Silver)
3-080-206-21
3-318-203-11
2-655-582-11
3-067-187-11
1.75
2.0
2.0
2.0
6.0
5.0
4.0
3.5
#57: M1.7 X 4.0
(Black)
#58: M2.0 X 6.0 (Tapping)
(Silver)
#59: M2.0 X 5.0 (Tapping)
(Silver)
#60: M2.6 X 5.0
(Black)
7-627-852-18
3-719-408-11
3-080-205-21
3-061-062-11
1.7
2.0
2.6
2.0
4.0
6.0
5.0
5.0
HARDWARE LIST (4/7)
#64: M1.7 X 5.0 (Tapping)
(Silver)
#61: M3.0 X 10.0
(Black)
#62: M2.0 X 3.0
#63: M5.0 X 12.5
(Black)
(Silver)
2-666-551-21
7-682-549-09
3-080-202-21
3-060-811-21
3.0
2.0
1.7
5.0
12.5
10.0
5.0
3.0
#65: M1.4 X 3.5
(Silver)
#66: M1.4 X 1.4
(Silver)
#67: M1.4 X 2.0
(Silver)
#68: M1.7 X 4.0
(Silver)
2-635-591-01
2-635-591-41
3-389-523-16
2-655-581-01
1.4
1.7
1.4
1.4
2.0
4.0
3.5
1.4
#69: M1.7 X 3.0
(Silver)
#70: M1.7 X 5.0
(Silver)
#71: M1.4 X 2.0
(Red)
#72: M1.4 X 2.0
(Silver)
2-599-475-21
2-599-475-41
3-208-537-01
4-663-621-41
1.7
1.7
1.4
1.4
5.0
3.0
2.0
2.0
#73: M1.2 X 4.0 (Tapping)
(Black)
#74: M1.7 X 6.0 (Tapping)
(Silver)
#75: M1.7 X 3.5 (Tapping)
(Silver)
#76: M1.7 X 4.0 (Tapping)
(Silver)
3-086-156-61
2-666-551-31
2-666-551-01
2-666-551-11
1.2
1.7
1.7
1.7
4.0
6.0
3.5
4.0
#77: M1.2 X 5.0 (Tapping)
(Silver)
#78: M1.4 X 3.5
(Red)
#79: M1.4X 2.0
(Silver)
#80: M1.4X 2.0
(Black)
3-086-156-31
3-208-537-11
2-587-151-11
3-279-411-01
1.4
1.4
1.4
1.2
5.0
3.5
2.0
2.0
HARDWARE LIST (5/7)
#81: M1.7 X 2.5
(Silver)
#82: M1.4 X 1.4
#83: M1.7 X 7.0 (Tapping)
#84: M2.0 X 3.0
(Silver)
(Silver)
(Black)
2-515-756-01
3-272-251-01
3-080-204-41
3-072-453-11
1.7
1.7
2.0
1.7
1.4
1.4
1.7
1.7
1.7
2.0
7.0
3.0
2.5
1.4
#85: M1.7 X 2.5
(Black)
#86: M1.7 X 4.0 (Tapping)
(Silver)
#87: M1.6 X 5.3
(Black)
#88: M1.6 X 5.9 (Tapping)
(Silver)
2-515-483-11
2-695-434-21
2-689-328-01
2-689-015-01
1.6
1.6
2.0
1.4
2.0
5.9
5.3
2.5
4.0
#89: M2.0 X 5.5 (Tapping)
(Silver)
#90: M1.7 X 3.0
(Silver)
#91: M1.7 X 3.0 (Tapping)
(Silver)
#92: M2.0 X 3.9
(Black)
2-695-575-01
3-271-395-01
2-695-434-11
3-268-954-01
1.7
5.0
3.0
3.9
3.5
#93: M1.7 X 3.5 (Tapping)
(Silver)
#94: M1.7 X 4.0
(Black)
#95: M3.0 X 8.0 (Tapping)
(Black)
#96: M1.4 X 2.5
(Silver)
3-254-082-01
2-515-483-31
7-685-646-79
2-587-151-21
1.7
3.0
8.0
3.5
4.0
2.5
#97: M1.4 X 2.5
(Black)
#98: M3.0 X 8.0
(Silver)
#99: M2.5 X 6.0 (Tapping)
(Silver)
#100: M2.0 X 6.0
(Black)
2-662-396-31
3-077-331-01
3-776-750-02
3-080-203-51
3.8
2.5
8.0
6.0
6.0
2.5
HARDWARE LIST (6/7)
#101: M2.0 X 5.0
(Silver)
#102: M2.6 X 8.0
#103: M2.6 X 10.0
(Silver)
#104: M3.0 X 8.0
(Black)
(Black)
7-621-555-39
7-621-284-30
7-685-794-09
7-682-548-09
2.6
2.6
3.0
2.0
8.0
10.0
8.0
5.0
#105: M2.0 X 4.0
(Red)
#106: M2.0 X 6.0
(Black)
#107: M2.0 X 5.0
(Silver)
#108: M1.7 X 3.0 (Tapping)
(Black)
2-891-494-31
3-713-786-11
3-032-750-01
2-695-430-01
2.0
2.0
2.0
1.7
4.0
6.0
5.0
3.0
#109: M1.7 X 3.0
(Black)
#110: M2.0 X 3.0
(Black)
#111: M1.7 X 4.0 (Tapping)
(Black)
#112: M1.4 X 5.0
(Black)
2-515-483-21
2-630-005-21
2-887-124-01
2-178-410-11
1.7
2.0
1.7
1.4
4.0
3.0
3.0
5.0
#113: M1.7 X 5.0
(Black)
#114: M2.0 X 5.5 (Tapping)
(Silver)
#115: M1.4 X 3.5 (Tapping)
(Silver)
#116: M2.0 X 3.5 (Tapping)
(Silver)
2-635-562-41
2-698-464-01
3-348-998-51
2-695-435-01
2.0
1.4
2.0
1.7
5.0
5.5
3.5
3.5
#117: M1.7 X 4.5 (Tapping)
(Silver)
#118: M1.4 X 2.0
(Black)
#119: M2.6 X 5.0
(Black)
#120: M2.6 X 6.0
(Silver)
2-695-429-31
2-655-580-01
7-627-556-58
7-621-770-67
2.6
1.7
1.4
2.6
6.0
4.5
2.0
5.0
HARDWARE LIST (7/7)
#121: M2.0 X 4.0 (Tapping)
(Silver)
#122: M3.0 X 6.0
#123: M4.0 X 8.0
(Black)
#124: M1.7 X 2.0
(Silver)
(Black)
3-080-205-11
7-682-547-09
7-682-561-09
2-599-475-01
3.0
4.0
2.0
1.7
6.0
8.0
2.0
4.0
Reverse
985225431.pdf
Revision History
S.M. Rev.
issued
—
Ver.
Date
History
Contents
1.0
2008.01 Official Release
—
HDR-SR11/SR11E/SR12/SR12E_L2
|
