Safety Instructions
Do not excessively bend the plug and wire nor place heavy objects
upon them, which could cause damage.
•
This may cause electric shock or fire.
Do not connect too many extension cords or plugs to one outlet.
This may cause fire.
•
Do not disconnect the power cord while using the monitor.
•
A surge may be caused by the separation and may damage the mon-
itor.
Do not use the power cord when the connector or plug is dusty.
•
•
If the connector or plug of the power cord is dusty, clean it with a dry
cloth.
Using the power cord with a dusty plug or connector may cause an
electric shock or fire.
To disconnect the apparatus from the mains, the plug must be pulled
out from the mains socket, therefore the mains plug shall be readily op-
erable.
•
This may cause electric shock or fire.
Installation
a location with heavy dust, high or low temperatures, high humidity, and exposed
to chemical substances and where it operates for 24 hours such as at airports,
train stations etc.
Failure to do so may cause serious damage to your monitor.
Place your monitor in a location with low humidity and a minimum
of dust.
•
Failure to do so may cause electric shock or fire inside the monitor.
Do not drop the monitor when moving it.
•
This may cause damage to the product or the person carrying it.
Install the monitor base in a showcase or shelf so that the end of the
base does not protrude from the showcase or shelf.
•
Dropping the product may cause damage to the product or the person
carrying it.
Do not place the product on an unstable or small surface area.
•
Place the product on an even and stable surface, as the product may
fall and cause harm to someone walking by, specifically children.
2
Safety Instructions
Do not place the product on the floor.
•
Take care, as someone, specifically children may trip over it.
TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR
OTHER OPEN FLAMES AWAY FROM THIS PRODUCT AT ALL
TIMES.
•
Otherwise, this may cause fire.
Keep any heating devices away from the power cable.
•
A melted coating may cause electric shock or fire.
Do not install the product in places with poor ventilation, for instance,
a bookshelf, closet, etc.
•
Any increase in the internal temperature may cause fire.
Put down the monitor carefully.
•
Failing to do so may damage the monitor.
Do not place the monitor face down.
•
This may damage the TFT-LCD surface.
The installation of the bracket must be done by a qualified professional.
Installing the bracket by unqualified personnel may result in injury.
•
•
Always use the mounting device specified in the owner's manual.
When installing the product, make sure to keep it away from the wall
(more than 10 cm / 4 inches) for ventilation purposes.
•
Poor ventilation may cause an increase in the internal temperature of
the product, resulting in a shortened component life and degraded
performance.
Keep the plastic packaging (bag) out of children's reach.
•
The plastic packaging (bag) may cause suffocation if children play
with it.
If the height of your monitor is adjustable, do not place any object or
part of your body on the stand when lowering it.
•
This may cause damage to the product or the person carrying it.
Clean
When cleaning the monitor case or the surface of the TFT-LCD screen, wipe
with a slightly moistened, soft fabric.
3
Safety Instructions
Do not spray water or detergent directly onto the monitor.
This may cause damage, electric shock or fire.
•
Use the recommended detergent with a smooth cloth.
If the connector between the plug and the pin is dusty or dirty, clean
it properly using a dry cloth.
•
A dirty connector may cause electric shock or fire.
Make sure to unplug the power cord before cleaning the product.
Otherwise, this may cause electric shock or fire.
•
Unplug the power cord from the power outlet and wipe the product
using a soft, dry cloth.
•
Do not use any chemicals such as wax, benzene, alcohol, thinners,
insecticide, air freshener, lubricant or detergent.
Others
Do not remove the cover (or back).
This may cause electric shock or fire.
•
•
Refer to a qualified servicing company.
If your monitor does not operate normally - in particular, if there is
any unusual sound or smell coming from the monitor - unplug it imme-
diately and contact an authorized dealer or the Service Center.
•
This may cause electric shock or fire.
Keep the product away from places exposed to oil, smoke or moisture;
do not install inside a vehicle.
•
•
This may cause a malfunction, electric shock or fire.
In particular, avoid operating the monitor near water or outdoors
where the monitor could be exposed to snow or rain.
If the monitor is dropped or the casing is damaged, turn the monitor
off and unplug the power cord. Then contact the Service Center.
•
The monitor may malfunction, causing electric shock or fire.
Disconnect the plug from the outlet during storms or lightning or if it
is not used for a long period of time.
•
Failure to do so may cause electric shock or fire.
4
Safety Instructions
Do not try to move the monitor by pulling only the wire or the signal
cable.
•
This may cause a breakdown, electric shock or fire due to damage to
the cable.
Do not move the monitor right or left by pulling only the wire or the
signal cable.
•
This may cause a breakdown, electric shock or fire due to damage to
the cable.
Do not cover the vents on the monitor cabinet.
•
Bad ventilation may cause a breakdown or fire.
Do not place water containers, chemical products or small metal ob-
jects on the monitor.
•
•
This may cause a malfunction, electric shock or fire.
If a foreign substance enters the monitor, unplug the power cord and
contact the Service Center.
Keep the product away from combustible chemical sprays or inflam-
mable substances.
•
This may cause an explosion or fire.
Never insert anything metallic into the monitor openings.
This may cause electric shock, fire or injury.
•
Do not insert metal objects such as chopsticks, wire and tools or in-
flammable objects such as paper or matches into the vent, headphone port
or AV ports or etc.
•
This may cause electric shock or fire. If an alien substances or water
enters the product, turn the product off, unplug the power connector
from the wall outlet and contact the Service Center.
When viewing a fixed screen for an extended period of time, residual
image or blurriness may appear.
•
Change the mode to energy saving mode or set a screensaver to a
changing picture when away from the monitor for an extended period
of time.
model.
•
An inappropriate resolution may cause undesirable picture quality.
Keep the volume at a comfortable level when using the headphones.
Excessively loud volume level may damage hearing.
•
5
Safety Instructions
Viewing the monitor continuously at a too close angle may result in
damage to your eyesight.
To ease eye strain, take at least a five-minute break after every hour
of using the monitor.
Do not install the product on an unstable, uneven surface or a location
prone to vibrations.
•
Dropping the product may cause damage to the product or the person
carrying it. Using the product in a location prone to vibrations may
shorten the lifetime of the product or may cause the product to catch
fire.
When moving the monitor, turn off and unplug the power cord. Make
sure that all cables, including the antenna cable and cables connected to
other devices, are disconnected before moving the monitor.
•
Failure to disconnect cables may damage it and cause fire or electric
shock.
Place the product out of children’s reach, as they could damage by
hanging onto it.
•
A falling product may cause injury to the person or even fatality.
When not using the product for an extended period of time, keep the
product unplugged.
•
Otherwise, this may cause heat emission from the accumulated dirt
or degraded insulation, causing electric shock or fire.
Do not place your children's favorite toys or any other objects of in-
terest on the product.
•
Children may try to climb on the product to retrieve an object. The
product could fall, causing injury or even fatality.
When lifting up or moving the monitor, do not lift the monitor upside
down while holding only the stand.
•
This may cause your monitor to fall, and become damaged or cause
personal injury.
Good Postures When Using the Monitor
Try to maintain a good posture when using the monitor.
•
•
Keep your back straight.
Keep a distance of about 45 ~ 50 cm between your eyes
and the monitor screen. Look at the screen from slightly
above it, and have the monitor directly in front of you.
•
Tilt the monitor upwards by 10 ~ 20 degrees. Adjust the
monitor height so that the top of the monitor is slightly
below eye level.
6
Safety Instructions
•
Adjust the monitor angle so that there is no reflected
light on the screen. Try to maintain your arms perpen-
dicular to your armpits.
•
•
•
Keep your arms level with the back of your hands.
Keep the angle of the elbow perpendicular.
Keep the angle of the knees at more than 90 degree. Do
not let your feet fall up from the floor. Adjust the arm
position so that it is below the heart.
7
Introduction
Package Contents
Note
Please make sure the following items are included with your monitor.
Contact a local dealer to buy optional items.
Unpacking
Type 1
Monitor & Simple stand
Note
MagicRotation program can not be provided as Simple Stand does not support Pivot function.
Type2
Monitor & HAS stand
Manuals
Quick Setup Guide
Warranty Card
8
User's Guide
Introduction
Cables
D-Sub Cable
Audio Cable
Power Cord
DVI Cable (option)
Your Monitor
Initial Settings
Select the language using the up or down key.
The displayed content will disappear after 40 seconds.
Turn the Power button off and on. It will be displayed again.
It can be displayed up to three (3) times. Make sure to adjust the resolution of your PC before reaching
the maximum count.
Note
The resolution displayed on the screen is the optimal resolution for this product.
Adjust your PC resolution so that it is the same as the optimal resolution for this product.
9
Introduction
Front
MENU button [MENU/
]
Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu
or return to the previous menu.
Customized Key[
]
You can customize key assignment for the Custom button according to your pref-
erences.
Note
Volume button [
]
When OSD is not on the screen, push the button to adjust volume.
Adjust buttons [
]
These buttons allow you to adjust items in the menu.
Enter button [ ] / SOURCE button
Activates a highlighted menu item.
Push the ' /SOURCE', then selects the video signal while the OSD is off. (When
the
/SOURCE button is pressed to change the input mode, a message appears
in the upper left of the screen displaying the current mode -- analog or digital input
signal.)
10
Introduction
Note
If you select the digital mode, you must connect your monitor to the graphic card's
DVI port using the DVI cable.
AUTO button
Use this button for auto adjustment.
Power button [
]
Use this button for turning the monitor on and off.
Power Indicator
This light glows blue during normal operation, and blinking blue once as the mon-
itor saves your adjustments.
Note
saving functions. For energy conservation, turn your monitor OFF when it is not
needed or when leaving it unattended for long periods.
[
]Headphone sound output terminal
Speaker
You can hear sound by connecting the soundcard of your PC to the monitor.
Rear
Note
The configuration at the back of the monitor may vary from product to product.
Simple Stand
HAS Stand
POWER port
11
Introduction
Connect the power cord for your monitor to the POWER port on the back of the
monitor.
AUDIO IN
Connect the audio cable for your monitor to the audio port on the back of your com-
puter.
DVI IN port
Connect the DVI Cable to the DVI IN port on the back of your monitor.
RGB IN port
Connect the D-sub cable to the 15-pin, RGB IN port on the back of your monitor.
Kensington Lock
The Kensington lock is a device used to physically fix the system when using it in a
public place. (The locking device has to be purchased separately.) For using a locking
device, contact where you purchase it.
Note
See Connecting Cables for further information regarding cable connections.
Cable holding ring
•
Fix the cables using the holding ring, as shown in the figure.
12
Connections
Connecting Cables
Connect the power cord for your monitor to the power port on the back of the monitor.
Plug the power cord for the monitor into a nearby outlet.
Use a connection appropriate for your computer.
Using the D-sub (Analog) connector on the video card.
•
•
•
Connect the signal cable to the 15-pin, D-sub port on the back of your monitor.
[RGB IN]
Using the DVI (Digital) connector on the video card.
Connect the DVI Cable to the DVI IN Port on the back of your Monitor.
[DVI IN]
Connected to a Macintosh.
Connect the monitor to the Macintosh computer using the D-sub connection cable.
Note
If the monitor and the computer are connected, you can turn them on and use them.
13
Connections
Using the Stand
Monitor Assembly
Simple Stand
Monitor and Bottom
HAS Stand
HAS Stand
A. Stand Stopper
Attaching a Base
This monitor accepts a 75 mm x 75 mm VESA-compliant mounting interface pad.
Simple Stand
HAS Stand
14
Connections
A. Monitor
B. Mounting interface pad (Sold separately)
1. Turn off your monitor and unplug its power cord.
2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen.
3. Remove two screws and then remove the stand from the LCD monitor.
4. Align the mounting interface pad with the holes in the rear cover mounting pad and secure it with
four screws that came with the arm-type base, wall mount hanger or other base.
•
•
•
Do not use screws longer than the standard dimension, as they may damage the
inside of the Monitor.
For wall mounts that do not comply with VESA standard screw specifications,
the length of the screws may differ depending on their specifications.
Do not use screws that do not comply with the VESA standard screw specifica-
tions.
Do not fasten the screws too tightly, as this may damage the product or cause the
product to fall, leading to personal injury.
Samsung is not liable for these kinds of accidents.
•
Samsung is not liable for product damage or personal injury when a non-VESA
or non-specified wall mount is used or the consumer fails to follow the product
installation instructions.
•
•
To mount the monitor on a wall, you should purchase the wall mounting kit that
allows you to mount the monitor at least 10 cm away from the wall surface.
Electronics will not be responsible for damages caused by using a base other than
those specified.
•
Please use Wall Mount according to the International standards.
15
Using the Software
Monitor Driver
Note
When prompted by the operating system for the monitor driver, insert the CD-ROM
included with this monitor. Driver installation is slightly different from one operating
system to another. Follow the directions appropriate for the operating system you
have.
Prepare a blank disk and download the driver program file at the Internet web site
shown here.
Internet web site :
Installing the Monitor Driver (Automatic)
1. Insert CD into the CD-ROM drive.
3. Choose your monitor model in the model list, then click the "OK" button.
4. If you can see following message window, then click the "Continue Anyway" button. Then click
"OK" button (Microsoft® Windows® XP/2000 Operating System).
16
Using the Software
Note
This monitor driver is under certifying MS logo, and this installation doesn't damage your system.
The certified driver will be posted on Samsung Monitor homepage.
Installing the Monitor Driver (Manual)
Microsoft® Windows Vista™‚ Operating System
1. Insert your Manual CD into your CD-ROM drive.
2.
Click
(Start) and "Control Panel". Then, double-click on "Appearance and Personalization".
3. Click "Personalization" and then "Display Settings".
4. Click "Advanced Settings...".
5. Click "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means the
configuration for your monitor is completed. The monitor can be used as is.
If the message "Windows needs..." is displayed, as shown in the figure below, click "Continue".
17
Using the Software
Note
This monitor driver is under certifying MS logo, and this installation doesn't damage your system.
The certified driver will be posted on Samsung Monitor homepage.
6. Click "Update Driver..." in the "Driver" tab.
7. Check the "Browse my computer for driver software" checkbox and click "Let me pick from a
list of device drivers on my computer".
8. Click "Have Disk...” and select the folder (for example, D:\Drive) where the driver setup file is
located, and click "OK".
18
Using the Software
9. Select the model that matches your monitor from the list of monitor models on the screen, and
click "Next".
10. Click "Close" → "Close" → "OK" → "OK" on the following screens displayed in sequence.
Microsoft® Windows® XP Operating System
19
Using the Software
1. Insert CD into the CD-ROM drive.
2. Click "Start" → "Control Panel" then click the "Appearance and Themes" icon.
3. Click "Display" icon and choose the "Settings" tab then click "Advanced...".
4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab.
5. Click "Update Driver..." and select "Install from a list or..." then click "Next" button.
6. Select "Don't search, I will..." then click "Next" and then click "Have disk".
20
Using the Software
7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model
list and click the "Next" button.
8. If you can see following message window, then click the "Continue Anyway" button. Then click
"OK" button.
Note
This monitor driver is under certifying MS logo, and this installation doesn't damage your system.
The certified driver will be posted on Samsung Monitor homepage.
9. Click the "Close" button then click "OK" button continually.
21
Using the Software
10. Monitor driver installation is completed.
Microsoft® Windows® 2000 Operating System
When you can see "Digital Signature Not Found" on your monitor, follow these steps.
1. Choose "OK" button on the "Insert disk" window.
2. Click the "Browse" button on the "File Needed" window.
3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button.
How to install
1. Click "Start", "Setting", "Control Panel".
2. Double click the "Display" icon.
3. Select the "Settings" tab and click "Advanced Properties" button.
4. Choose "Monitor".
Case1 : If the "Properties" button is inactive, it means your monitor is properly configured. Please
stop installation
Case2 : If the "Properties" button is active, click the "Properties" button then follow next steps
continually.
5. Click "Driver" and then click on "Update Driver..." then click on the "Next" button.
6. Choose "Display a list of the known drivers for this device so that I can choose a specific driver"
then click "Next" and then click "Have disk".
7. Click the "Browse" button then choose A:(D:\Driver).
8. Click the "Open" button, then click "OK" button.
9. Choose your monitor model and click the "Next" button then click "Next" button.
10. Click the "Finish" button then the "Close" button.
If you can see the "Digital Signature Not Found" window then click the "Yes" button. And click
the "Finish" button then the "Close" button.
Microsoft® Windows® Millennium Operating System
1. Click "Start", "Setting", "Control Panel".
2. Double click the "Display" icon.
3. Select the "Settings" tab and click "Advanced Properties" button.
22
Using the Software
4. Select the "Monitor" tab.
5. Click the "Change" button in the "Monitor Type" area.
6. Choose "Specify the location of the driver".
7. Choose "Display a list of all the driver in a specific location..." then click "Next" button.
8. Click the "Have Disk" button.
9. Specify A:\(D:\driver) then click "OK" button.
10. Select "Show all devices" and choose the monitor that corresponds to the one you connected to
your computer and click "OK".
11. Continue choosing "Close" button and "OK" button until you close the Display Properties dia-
logue box.
Microsoft® Windows® NT Operating System
1. Click "Start", "Settings", "Control Panel", and then double-click "Display" icon.
2. In Display Registration Information window, click Settings Tab and then click "All Display
Modes".
3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and
then click "OK".
4. Click "Apply" button if you see the screen working normally after clicking "Test". If the screen
is not normal, change to a different mode (lower mode of resolution, colors or frequency).
Note
If there is no Mode at All Display Modes, select the level of resolution and vertical frequency by
referring to the Preset Timing Modes in the user guide.
Linux Operating System
To execute X-Window, you need to make the X86Config file, which is a type of system setting file.
1. Press "Enter" at the first and the second screen after executing the X86Config file.
2. The third screen is for setting your mouse.
3. Set a mouse for your computer.
4. The next screen is for selecting a keyboard.
5. Set a Keyboard for your computer.
6. The next screen is for setting your monitor.
7. First of all, set a horizontal frequency for your monitor. (You can enter the frequency directly.)
8. Set a vertical frequency for your monitor. (You can enter the frequency directly.)
9. Enter the model name of your monitor. This information will not affect the actual execution of
X-Window.
10. You have finished setting up your monitor. Execute X-Window after setting other requested
hardware.
23
Using the Software
Natural Color
Natural Color Software Program
One of the recent problems in using a computer is that the color of the images printed out by a printer
or other images scanned by a scanner or a digital camera are not the same as those shown on the monitor.
The Natural Color S/W is the very solution for this problem. It is a color administration system de-
veloped by Samsung Electronics in association with Korea Electronics & Telecommunications
Research Institute (ETRI). This system is available only for Samsung monitors and makes the color
of the images on the monitor the same as the printed or scanned images. For more information, refer
to Help (F1) in the software program.
How to install the Natural Color software
Insert the CD included with the Samsung monitor into the CD-ROM Drive. Then, the initial screen of
the program Natural Color will be executed. Click Natural Color on the initial screen to install the
Natural Color software.
To install the program manually, insert the CD included with the Samsung monitor into the CD-ROM
Drive, click the [Start] button of Windows and then select [Run...]. Enter D:\color\NCProSetup.exe
and then press the [Enter] key. (If the drive where the CD is inserted is not D:\, enter the applicable
drive.)
How to delete the Natural Color software program
Select "Setting/Control Panel" on the "Start" menu and then double-click "Add/Delete a program".
Select Natural Color from the list and then click the "Add/Delete" button.
MagicTune™
24
Using the Software
Installation
1. Insert the installation CD into the CD-ROM drive.
2. Click the MagicTune™ installation file.
Note
If the popup window to install the software for the main screen is not displayed, proceed with the
installation using the MagicTune executable file on the CD.
3. Select installation Language, Click "Next".
4. When the Installation Shield Wizard window appears, click "Next".
5. Select "I agree to the terms of the license agreement" to accept the terms of use.
6. Choose a folder to install the MagicTune™ program.
7. Click "Install".
8. The "Installation Status" window appears.
9. Click "Finish".
10. When the installation is complete, the MagicTune™ executable icon appears on your desktop.
Double-click the icon to start the program.
MagicTune™ execution icon may not appear depending on specification of computer sys-
tem or monitor. If that happens, press F5 Key.
Installation Problems
The installation of MagicTune™ can be affected by such factors as the video card, motherboard and
the network environment.
System Requirements
OS
•
•
•
•
Windows 2000
Windows XP Home Edition
Windows XP Professional
Windows Vista™
It is recommended using MagicTune™ in Windows® 2000 or later.
Hardware
•
•
32 MB Memory above
60 MB Hard disk space above
For more information, visit the MagicTune™ website.
25
Using the Software
Uninstall
The MagicTune™ program can be removed only by using the "Add or Remove Programs" option of
the Windows® Control Panel.
Perform the following steps remove MagicTune™.
1. Go to [Task Tray] → [Start] → [Settings] and select [Control Panel] in the menu. If the program
runs on Windows® XP, go to [Control Panel] in the [Start] menu.
2. Click the "Add or Remove Programs" icon in Control Panel.
3. In the "Add or Remove Programs" screen, scroll down to find "MagicTune™." Click on it to
highlight it.
4. Click the "Change/Remove" button to remove the program.
5. Click "Yes" to begin the uninstall process.
6. Wait until the "Uninstall Complete" dialog box appears.
Note
and software upgrades.
MagicRotation
Installation
1. Insert the installation CD into the CD-ROM drive.
2. Click the MagicRotation installation file.
Note
If the popup window to install the software for the main screen is not displayed, proceed with the
installation using the MagicTune executable file on the CD.
3. Select installation Language, Click "Next".
4. When the Installation Shield Wizard window appears, click "Next".
5. Select "I agree to the terms of the license agreement" to accept the terms of use.
26
Using the Software
6. Choose a folder to install the MagicRotation program.
7. Click "Install".
8. The "Setup Status" window appears.
9. Click "Finish".
Have to reboot the system in order for the MagicRotation to work properly.
10. When the installation is complete, the MagicRotation executable icon appears on your desktop.
Installation Problems
The installation of MagicRotation can be affected by such factors as the video card, motherboard and
the network environment.
Limitation
1. The "Display Driver" should be properly loaded for the MagicRotation to work properly.
The installed "Display Driver" should be the latest driver supplied by the vendor.
2. If some applications like Windows Media Player, Real Player, etc. are not displaying movie files
properly in 90, 180 and 270 orientations then do the following :
•
•
•
Close the application.
Select the Orientation (90, 180, 270) you want to view the application.
Relaunch the application.
In most cases this should fix the problem.
3. User Applications using OpenGL and DirectDraw (3D drawing) will not function as per the
orientation mode selected (90, 180, 270).
e.g. 3D games
4. DOS based applications in Full Screen Mode will not function as per the orientation mode selected
(90, 180, 270).
5. Dual is not supported in Windows®‚ 98, ME, NT 4.0.
6. MagicRotation does not provide support for 24 bits per pixel (Bit depth/Color Quality).
7. If you are changing your Graphic Card it is recommended that you uninstall the MagicRotation
Software before doing so.
System Requirements
OS
•
•
Windows 98 SE
Windows ME
27
Using the Software
•
•
•
•
•
Windows NT 4.0
Windows 2000
Windows XP Home Edition
Windows XP Professional
Windows Vista™
Hardware
•
•
128 MB Memory above (recommended)
25 MB Hard disk space above
Service Packs
•
•
It is recommended that your System has the latest Service Pack installed.
For Windows®‚ NT 4.0, it is recommended to install Internet Explorer 5.0 and above with Active
Desktop component.
For more information, visit the MagicRotation website.
Windows®‚ is registered trademark of Microsoft Corporation,Inc.
Uninstall
The MagicRotation program can be removed only by using the "Add or Remove Programs" option of
the Windows® Control Panel.
Perform the following steps remove MagicRotation.
1. Go to [Task Tray] → [Start] → [Settings] and select [Control Panel] in the menu. If the program
runs on Windows® XP, go to [Control Panel] in the [Start] menu.
2. Click the "Add or Remove Programs" icon in Control Panel.
3. In the "Add or Remove Programs" screen, scroll down to find "MagicRotation." Click on it to
highlight it.
4. Click the "Change/Remove" button to remove the program.
5. Click "Yes" to begin the uninstall process.
6. Wait until the "Uninstall Complete" dialog box appears.
7. After uninstall restart the system to complete the uninstallation.
Note
swers) and software upgrades.
Windows®‚ is registered trademark of Microsoft Corporation,Inc
28
Adjusting the Monitor
Direct Functions
AUTO
When the 'AUTO' button is pressed, the auto adjustment screen appears as shown in the animated
screen on the center.
Auto adjustment allows the monitor to self-adjust to the incoming Analog signal. The values of Fine,
Coarse and Position are adjusted automatically.
(Available in Analog mode only)
To make the automatic adjustment function sharper, execute the 'AUTO' function while the AUTO
If auto adjustment does not work properly, press 'AUTO' button again to adjust picture with more
accuracy.
If you change resolution in the control panel, auto function will be executed automatically.
OSD Lock & Unlock
When pressing the AUTO button after locking the OSD
29
Adjusting the Monitor
When pressing the MENU button after locking the OSD
This is the function that locks the OSD in order to keep the current states of settings or prevent others
from adjusting the current settings.
Lock : Hold down the MENU button for more than five (5) seconds to activate the OSD adjustment
lock function.
Unlock : Hold down the MENU button for more than five (5) seconds to deactivate the OSD adjustment
lock function.
30
Adjusting the Monitor
Note
Though the OSD adjustment lock function is activated, you can still adjust the brightness and contrast,
and adjust Customized Key ( ) using the Direct button.
Customized key
You can customize key assignment for the Custom button according to your preferences.
To view the operating screen displayed when pressing the [
tomized key for a function, click the name of each function.
] button after configuring the cus-
Note
31
Adjusting the Monitor
Volume
When OSD is not on the screen, push the button to adjust volume.
SOURCE
Selects the video signal while the OSD is off.
OSD Function
32
Adjusting the Monitor
Picture
Brightness
(Not available in MagicBright mode of Dynamic Contrast.)
You can use the on-screen menus to change the brightness according to personal preference.
MENU → → MENU
→
→
,
Contrast
(Not available in MagicBright mode of Dynamic Contrast.)
33
Adjusting the Monitor
You can use the on-screen menus to change the contrast according to personal preference.
MENU →
→
,
→
→
,
→ MENU
MagicBright
Push the
button to circle through available preconfigured modes.
MagicBright is a new feature providing optimum viewing environment depending on the contents of
the image you are watching. Currently seven different modes are available: Custom, Text, Internet,
34
Adjusting the Monitor
Game, Sport, Movie and Dynamic Contrast. Each mode has its own pre-configured brightness value.
You can easily select one of seven settings by simply pressing Customized Key control button.
•
Custom
Although the values are carefully chosen by our engineers, the pre-configured values may not be
comfortable to your eyes depending on your taste.
If this is the case, adjust the brightness and contrast by using the OSD menu.
•
•
•
•
•
•
Text
For documentations or works involving heavy text.
Internet
For working with a mixture of images such as texts and graphics.
Game
For watching motion pictures such as a game.
Sport
For watching motion pictures such as a sport.
Movie
For watching motion pictures such as a DVD or Video CD.
Dynamic Contrast
Dynamic Contrast is to automatically detect distribution of inputted visual signal and adjust to
create optimum contrast.
MENU →
→
,
→
→
,
→ MENU
Color
(Not available in MagicBright mode of Dynamic Contrast.)
35
Adjusting the Monitor
MagicColor
MagicColor is a new technology that Samsung has exclusively developed to improve digital image
and to display natural color more clearly without disturbing image quality.
•
•
Off - Returns to the original mode.
Demo - The screen before applying MagicColor appears on the right and the screen after applying
MagicColor appears on the left.
•
•
Full - Displays not only vivid natural color but also more realistic natural skin color with clearness.
Intelligent - Displays vivid natural color with clearness.
MENU →
,
→
→
→
,
→ MENU
36
Adjusting the Monitor
Color Tone
The tone of the color can be changed and one of four modes can be selected.
•
•
•
•
Cool - Makes whites bluish.
Normal - Keeps whites white.
Warm - Makes whites reddish.
Custom - Select this mode when you want to adjust the image according to your preferences.
MENU →
,
→
→
,
→
→
,
→ MENU
37
Adjusting the Monitor
Color Control
Adjusts individual Red, Green, Blue color balance.
MENU →
,
→
→
,
→
→
,
→
→
,
→ MENU
Color Effect
You can change the overall mood by changing the screen colors.
38
Adjusting the Monitor
•
Off
•
Grayscale
•
Green
•
Aqua
•
Sepia
•
Off - This applies an achromatic color to the screen to adjust the screen effects.
Grayscale - The default colors of black and white are displayed.
Green - This applies the green color effect to a black and white screen.
Aqua - This applies the aqua color effect to a black and white screen.
Sepia - This applies the Sepia color effect to a black and white screen.
•
•
•
•
MENU →
,
→
→
,
→
→
,
→ MENU
Gamma
Gamma correction changes the luminance of the colors with intermediate luminance.
•
Mode 1
•
Mode 2
•
,
Mode 3
MENU →
,
→
→
,
→
→
→ MENU
39
Adjusting the Monitor
Image
Coarse
Removes noise such as vertical stripes.
Coarse adjustment may move the screen image area. You may relocate it to the center using the
horizontal control menu.
(Available in Analog mode only)
MENU →
,
→
→
→
,
→ MENU
40
Adjusting the Monitor
Fine
Removes noise such as horizontal stripes.
If the noise persists even after Fine tuning, repeat it after adjusting the frequency (clock speed).
(Available in Analog mode only)
MENU →
,
→
→
,
→
→
,
→ MENU
Sharpness
Changes the clearance of image.
41
Adjusting the Monitor
MENU →
,
→
→
,
→
→
,
→ MENU
H-Position
Changes the horizontal position of the monitor's entire display.
(Available in Analog mode only)
MENU →
,
→
→
,
→
→
,
→ MENU
V-Position
42
Adjusting the Monitor
Changes the vertical position of the monitor's entire display.
(Available in Analog mode only)
MENU →
,
→
→
,
→
→
,
→ MENU
OSD
Language
You can choose one of nine languages.
Note
The language chosen affects only the language of the OSD. It has no effect on any software running
on the computer.
MENU →
,
→
→
→
,
→ MENU
43
Adjusting the Monitor
H-Position
You can change the horizontal position where the OSD menu appears on your monitor.
MENU → → MENU
,
→
→
,
→
→
,
V-Position
You can change the vertical position where the OSD menu appears on your monitor.
MENU →
,
→
→
,
→
→
,
→ MENU
44
Adjusting the Monitor
Transparency
Change the transparency of the background of the OSD.
Off On
MENU → → MENU
•
•
,
→
→
,
→
→
,
Display Time
The menu will be automatically turned off if no adjustments are made for a certain time period.
You can set the amount of time the menu will wait before it is turned off.
45
Adjusting the Monitor
•
5 sec
•
10 sec
•
,
20 sec
•
200 sec
MENU →
,
→
→
,
→
→
→ MENU
Setup
Reset
Reverts the product settings to factory defaults.
No Yes
MENU → → MENU
•
•
,
→
→
,
→
46
Adjusting the Monitor
Customized Key
You can specify a function which will be activated when the Customized Key (
MENU → →MENU
)is pressed.
,
→
→
,
→
→
,
Off Timer
The monitors will turn off automatically at the specified time.
Off On
•
•
47
Adjusting the Monitor
MENU →
,
→
→
,
→
→
,
→
→ , → MENU
Auto Source
Select Auto Source for the monitor to automatically select the signal source.
Auto Manual
•
•
MENU →
,
→
→
→
,
→ MENU
Information
48
Adjusting the Monitor
Shows a video source, display mode on the OSD screen.
MENU →
,
→MENU
49
Troubleshooting
Self-Test Feature Check
Note
Your monitor provides a self test feature that allows you to check whether your monitor is functioning
properly.
Self-Test Feature Check
1. Turn off both your computer and the monitor.
2. Unplug the video cable from the back of the computer.
3. Turn on the monitor.
If the monitor is functioning properly, you will see a box in the illustration below.
This box appears during normal operation if the video cable becomes disconnected or damaged.
4. Turn off your monitor and reconnect the video cable; then turn on both your computer and the
monitor.
If your monitor screen remains blank after using the previous procedure, check your video controller
and computer system; your monitor is functioning properly.
Warning Messages
If there is something wrong with the input signal, a message appears on the screen or the screen goes
blank although the power indicator LED is still on. The message may indicate that the monitor is out
of scan range or that you need to check the signal cable.
Environment
The location and the position of the monitor may influence the quality and other features of the monitor.
If there are any sub woofer speakers near the monitor, unplug and relocate the woofer to another room.
Remove all electronic devices such as radios, fans, clocks and telephones that are within 3 feet (one
meter) of the monitor.
Useful Tips
A monitor recreates visual signals received from the computer. Therefore, if there is a problem with
the computer or the video card, this can cause the monitor to become blank, have poor coloring, become
noisy, and video mode not supported, etc. In this case, first check the source of the problem, and then
contact the Service Center or your dealer.
50
Troubleshooting
Judging the monitor's working condition
If there is no image on the screen or a "Not Optimum Mode", "Recommended Mode 1280 x 1024
60 Hz" message comes up, disconnect the cable from the computer while the monitor is still powered
on.
If there is a message coming up on the screen or if the screen goes white, this means the monitor is in
working condition.
In this case, check the computer for trouble.
Check List
Note
Before calling for assistance, check the information in this section to see if you can remedy any prob-
lems yourself. If you do need assistance, please call the phone number on the Information section or
No images on the screen. I cannot turn on the monitor.
Q:
A:
Q:
A:
Is the power cord connected properly?
Check the power cord connection and supply.
Can you see "Check Signal Cable" on the screen?
(Connected using the D-sub cable)
Check the signal cable connection.
(Connected using the DVI cable)
If you still see an error message on the screen when the monitor is connected properly, check to
see if the monitor status is set to analog.
If you still see an (error) message on the screen when the monitor is connected properly, check
to see if the monitor status is set to analog. Press ‘ /SOURCE’ button to have the monitor
double-check the input signal source.
Q:
A:
If the power is on, reboot the computer to see the initial screen (the login screen), which can be
seen.
If the initial screen (the login screen) appears, boot the computer in the applicable mode (the
safe mode for Windows ME/XP/2000) and then change the frequency of the video card.
If the initial screen (the login screen) does not appear, contact the Service Center or your deal-
Q:
A:
Can you see "Not Optimum Mode", "Recommended Mode 1280 x 1024 60 Hz" on the screen?
You can see this message when the signal from the video card exceeds the maximum resolution
and frequency that the monitor can handle properly.
A:
A:
Adjust the maximum resolution and frequency that the monitor can handle properly.
If the display exceeds SXGA or 75 Hz, a "Not Optimum Mode", "Recommended Mode 1280
x 1024 60 Hz" message is displayed. If the display exceeds 85 Hz, the display will work properly
51
Troubleshooting
but the "Not Optimum Mode", "Recommended Mode 1280 x 1024 60 Hz" message appears
for one minute and then disappears.
Please change to the recommended mode during this one-minute period.
(The message is displayed again if the system is rebooted.)
Q:
There is no image on the screen. Is the power indicator on the monitor blinking at 1 second
intervals?
A:
A:
A:
The monitor is in PowerSaver mode.
Press a key on the keyboard to activate the monitor and restore the image on the screen.
If there is still no image, press the ' /SOURCE' button. Then press any key on the keyboard
again to activate the monitor and restore the image on the screen.
Q:
A:
Connected using the DVI cable?
You may get a blank screen if you boot the system before you connect the DVI cable, or dis-
connect and then reconnect the DVI cable while the system is running as certain types of graphic
cards do not send out video signals. Connect the DVI cable and then reboot the system.
I cannot see the On Screen Display.
Q:
A:
Have you locked the On Screen Display (OSD) Menu to prevent changes?
Unlock the OSD by pressing the [MENU/ ] button for at least 5 seconds.
The screen shows strange colors or just black and white.
Q:
A:
A:
Q:
Is the screen displaying only one color as if looking at the screen through a cellophane paper?
Check the signal cable connection.
Make sure the video card is fully inserted in its slot.
Have the screen colors become strange after running a program or due to a crash between ap-
plications?
A:
Q:
A:
Reboot the computer.
Has the video card been set properly?
Set the video card by referring to the video card manual.
The screen suddenly has become unbalanced.
Q:
A:
Q:
A:
Have you changed the video card or the driver?
Adjust screen image position and size using the OSD.
Have you adjusted the resolution or frequency to the monitor?
Adjust the resolution and frequency at the video card.
Q:
The screen can be unbalanced due to the cycle of the video card signals. Readjust Position by
referring to the OSD.
52
Troubleshooting
The screen is out of focus or OSD cannot be adjusted.
Q:
A:
Have you adjusted the resolution or frequency on the monitor?
Adjust the resolution and frequency of the video card.
LED is blinking but no images on the screen.
Q:
A:
Is the frequency properly adjusted when checking the Display Timing on the menu?
Adjust the frequency properly by referring to the video card manual and the Preset Timing
Modes.
(The maximum frequency per resolution may differ from product to product.)
There are only 16 colors shown on the screen. The screen colors have
changed after changing the video card.
Q:
A:
Have the Windows colors been set properly?
Windows XP :
Set the resolution at the Control Panel → Appearance and Themes → Display → Settings.
Windows ME/2000 :
A:
Set the resolution at the Control Panel → Display → Settings.
Has the video card been set properly?
Q:
A:
Set the video card by referring to the video card manual.
There is a message that reads "Unrecognized monitor, Plug & Play (VE-
SA DDC) monitor found".
Q:
A:
Q:
A:
Have you installed the monitor driver?
See the video card manual to see if the Plug & Play (VESA DDC) function can be supported.
Problems related to Audio.
Q:
A:
No sound.
Ensure that the audio cable is firmly connected to both the audio-in port on your monitor and
the audio-out port on your sound card.
(Refer to Connecting Cables).
Check the volume level.
Sound level is too low.
Q:
A:
Check the volume level.
53
Troubleshooting
If the volume is still too low after turning the control to its maximum, check the volume control
on the computer sound card or software program.
Check when MagicTune™ does not function properly.
Q:
A:
MagicTune™ feature is found only on PC (VGA) with Window OS that supports Plug and Play.
To check whether your PC is available for MagicTune™ feature, follow the steps below (When
Windows is XP);
Control Panel → Performance and Maintenance → System → Hardware → Device Manager
→ Monitors → After deleting Plug and Play monitor, find 'Plug and Play monitor' by searching
new Hardware.
A:
MagicTune™ is an additional software for the monitor. Some graphic cards may not support
your monitor. When you have a problem with the graphic card, visit our website to check the
compatible graphic card list provided.
MagicTune™ doesn't work properly.
Q:
A:
Have you changed your PC or video graphic card?
Download the latest program. The program can be downloaded http://www.samsung.com/mon-
Q:
A:
Did you install the program?
Reboot the computer after installing the program for the first time. If a copy of the program is
already installed, remove it, reboot the computer, and then install the program again. You need
to reboot the computer for it to operate normally after installing or removing the program.
Note
Visit the MagicTune™ website and download the installation software for MagicTune™ MAC.
Check the following items if there is trouble with the monitor.
Check if the power cord and the video cables are properly connected to the computer.
Check if the computer beeps more than 3 times when booting.
(If it does, request an a service for the main board of the computer.)
If you installed a new video card or if you assembled the PC, check if the installed the adapter(video)
driver and the monitor driver.
Check if the scanning ratio of the video screen is set to between 56 Hz ~ 75 Hz.
(Do not exceed 75 Hz when using the maximum resolution.)
If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove
the Display Adapter in the "Control Panel → System → Device Administrator" and then reboot the
computer to reinstall the adapter (video) driver.
Note
54
Troubleshooting
Q & A
Q:
A:
A:
How can I change the frequency?
The frequency can be changed by reconfiguring the video card.
Note that video card support can vary, depending on the version of the driver used. (Refer to the
computer or the video card manual for details.)
Q:
A:
How can I adjusts the resolution?
Windows XP:
Set the resolution in the Control Panel → Appearance and Themes → Display → Settings.
Windows ME/2000:
A:
Set the resolution in the Control Panel → Display → Settings.
* Contact the video card manufacturer for details.
How can I set the Power Saving function?
Q:
A:
Windows XP:
Set the resolution in the Control Panel → Appearance and Themes → Display → Screen Saver.
Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Man-
ual).
A:
Windows ME/2000:
Set the resolution at the Control Panel → Display → Screen Saver.
Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Man-
ual).
Q:
A:
How can I clean the outer case/LCD Panel?
Disconnect the power cord and then clean the monitor with a soft cloth, using either a cleaning
solution or plain water.
Do not leave any detergent or scratches on the case. Do not let any water enter the monitor.
Note
Before calling for assistance, check the information in this section to see if you can remedy any prob-
lems yourself. If you do need assistance, please call the phone number on the Information section or
55
Specifications
General
General
Model Name
SyncMaster 743BM
LCD Panel
Size
17 inch(43 cm)
Display area
Pixel Pitch
337.920 mm (H) x 270.336 mm (V)
0.264 mm (H) x 0.264 mm (V)
Synchronization
Horizontal
30 ~ 81 kHz
56 ~ 75 Hz
Vertical
Display Color
16.7M
Resolution
Optimum resolution
Maximum resolution
1280 x 1024@60 Hz
1280 x 1024@75 Hz
Input Signal, Terminated
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
135 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable
Audio Signal
Audio Input
Audio Output
Speaker
1pin , PC Audio Signal Input
1pin , Earphone Connector
1Watt x 2
56
Specifications
Dimensions (W x H x D) / Weight (Simple Stand)
368.0 x 307.4 x 68.4 mm / 14.5 x 12.1 x 2.7 inch (Without Stand)
368.0 x 386.2 x 185.0 mm / 14.5 x 15.2 x 7.3 inch (With Stand), 3.7 kg / 8.2 lbs
Dimensions (W x H x D) / Weight (HAS Stand)
368.0 x 307.4 x 65.5 mm / 14.5 x 12.1 x 2.6 inch (Without Stand)
368.0 x 367.2 x 190.0 mm / 14.5 x 14.5 x 7.5 inch (With Stand), 4.75 kg / 10.5 lbs
VESA Mounting Interface
75 mm x 75 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Operating
Temperature : 50˚F ~ 104˚F (10˚C ~ 40˚C)
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4˚F ~ 113˚F (-20˚C ~ 45˚C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the
monitor and the computer systems will provide the best operating conditions and monitor
settings. In most cases, the monitor installation will proceed automatically, unless the user
wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with preci-
sion of 1ppm (one millionth) above are used for this product. But the pixels of RED,
GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may
be seen. This is not from bad quality and you can use it without any problems.
For example, the number of TFT-LCD sub pixels contained in this product are 3,932,160.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can
be used in all areas including common residential areas. (Class B equipment emits less electromagnetic
waves than Class A equipment.)
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy
by switching your monitor to low-power mode when it has not been used for a certain amount of time.
The monitor automatically returns to normal operation when you press a key on the keyboard. For
energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for
long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
57
Specifications
State
Normal Operation Power saving mode Power off (Power button)
EPA/ENERGY 2000
Power Indicator
Blue
32 watts
Blue blinking
1 watts
Off
1 watts
Power Consump-
tion
This monitor is EPA ENERGY STAR® compliant and EN-
ERGY2000 compliant when used with a computer equipped
with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined
that this product meets the ENERGY STAR® guidelines for
energy efficiency.
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the
screen will be adjusted automatically. However, if the signal differs, the screen may go blank while
the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
Horizontal Vertical Fre- Pixel Clock Sync Polarity
Frequency quency (Hz)
(kHz)
(MHz)
(H/V)
IBM, 640 x 350
IBM, 640 x 480
31.469
31.469
31.469
35.000
49.726
68.681
37.500
37.861
35.156
37.879
46.875
48.077
48.363
56.476
60.023
67.500
60.000
63.981
79.976
70.086
59.940
70.087
66.667
74.551
75.062
75.000
72.809
56.250
60.317
75.000
72.188
60.004
70.069
75.029
75.000
60.000
60.020
75.025
25.175
25.175
28.322
30.240
57.284
100.000
31.500
31.500
36.000
40.000
49.500
50.000
65.000
75.000
78.750
108.000
108.000
108.000
135.000
+/-
-/-
IBM, 720 x 400
-/+
-/-
MAC, 640 x 480
MAC, 832 x 624
MAC, 1152 x 870
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1152 x 864
VESA, 1280 X 960
VESA, 1280 X 1024
VESA, 1280 X 1024
-/-
-/-
-/-
-/-
+/+
+/+
+/+
+/+
-/-
-/-
+/+
+/+
+/+
+/+
+/+
Horizontal Frequency
The time to scan one line connecting the right edge to the
left edge of the screen horizontally is called the Horizontal
Cycle and the inverse number of the Horizontal Cycle is
called the Horizontal Frequency. Unit: kHz
58
Specifications
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same
image many times per second to display an image to the
user. The frequency of this repetition is called the Vertical
Frequency or Refresh Rate. Unit: Hz
General
General
Model Name
SyncMaster 943BM
LCD Panel
Size
19 inch(48 cm)
Display area
Pixel Pitch
376.32 mm (H) x 301.056 mm (V)
0.294 mm (H) x 0.294 mm (V)
Synchronization
Horizontal
30 ~ 81 kHz
56 ~ 75 Hz
Vertical
Display Color
16.7M
Resolution
Optimum resolution
Maximum resolution
1280 x 1024@60 Hz
1280 x 1024@75 Hz
Input Signal, Terminated
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
135 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable
Audio Signal
Audio Input
1pin , PC Audio Signal Input
1pin , Earphone Connector
Audio Output
59
Specifications
Audio Signal
Speaker
1Watt x 2
Dimensions (W x H x D) / Weight (Simple Stand)
405.6 x 335.2 x 66.7 mm / 16.0 x 13.2 x 2.6 inch (Without Stand)
405.6 x 413.5 x 200.0 mm / 16.0 x 16.3 x 7.9 inch (With Stand), 3.8 kg / 8.4 lbs
Dimensions (W x H x D) / Weight (HAS Stand)
405.6 x 335.2 x 63.8 mm / 16.0 x 13.2 x 2.6 inch (Without Stand)
405.6 x 380.2 x 190.0 mm / 16.0 x 15.0 x 7.5 inch (With Stand), 4.85 kg / 10.7 lbs
VESA Mounting Interface
75 mm x 75 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Operating
Temperature : 50˚F ~ 104˚F (10˚C ~ 40˚C)
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4˚F ~ 113˚F (-20˚C ~ 45˚C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the
monitor and the computer systems will provide the best operating conditions and monitor
settings. In most cases, the monitor installation will proceed automatically, unless the user
wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with preci-
sion of 1ppm (one millionth) above are used for this product. But the pixels of RED,
GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may
be seen. This is not from bad quality and you can use it without any problems.
For example, the number of TFT-LCD sub pixels contained in this product are 3,932,160.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can
be used in all areas including common residential areas. (Class B equipment emits less electromagnetic
waves than Class A equipment.)
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy
by switching your monitor to low-power mode when it has not been used for a certain amount of time.
The monitor automatically returns to normal operation when you press a key on the keyboard. For
energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for
60
Specifications
long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation Power saving mode Power off (Power button)
EPA/ENERGY 2000
Power Indicator
Blue
Blue blinking
1 watts
Off
1 watts
Power Consump-
tion
37 watts
This monitor is EPA ENERGY STAR® compliant and EN-
ERGY2000 compliant when used with a computer equipped
with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined
that this product meets the ENERGY STAR® guidelines for
energy efficiency.
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the
screen will be adjusted automatically. However, if the signal differs, the screen may go blank while
the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
Horizontal Vertical Fre- Pixel Clock Sync Polarity
Frequency quency (Hz)
(kHz)
(MHz)
(H/V)
IBM, 640 x 350
IBM, 640 x 480
31.469
31.469
31.469
35.000
49.726
68.681
37.500
37.861
35.156
37.879
46.875
48.077
48.363
56.476
60.023
67.500
60.000
63.981
79.976
70.086
59.940
70.087
66.667
74.551
75.062
75.000
72.809
56.250
60.317
75.000
72.188
60.004
70.069
75.029
75.000
60.000
60.020
75.025
25.175
25.175
28.322
30.240
57.284
100.000
31.500
31.500
36.000
40.000
49.500
50.000
65.000
75.000
78.750
108.000
108.000
108.000
135.000
+/-
-/-
IBM, 720 x 400
-/+
-/-
MAC, 640 x 480
MAC, 832 x 624
MAC, 1152 x 870
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1152 x 864
VESA, 1280 X 960
VESA, 1280 X 1024
VESA, 1280 X 1024
-/-
-/-
-/-
-/-
+/+
+/+
+/+
+/+
-/-
-/-
+/+
+/+
+/+
+/+
+/+
61
Specifications
Horizontal Frequency
The time to scan one line connecting the right edge to the
left edge of the screen horizontally is called the Horizontal
Cycle and the inverse number of the Horizontal Cycle is
called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same
image many times per second to display an image to the
user. The frequency of this repetition is called the Vertical
Frequency or Refresh Rate. Unit: Hz
62
Information
For Better Display
Adjust the computer resolution and screen injection rate (refresh rate) on the computer
as described below to enjoy the best picture quality. You can have an uneven picture quality
on screen if the best picture quality is not provided for TFT-LCD.
•
•
Resolution: 1280 x 1024
Vertical frequency (refresh rate): 60 Hz
TFT-LCD panels manufactured by using advanced semiconductor technology with a
precision of 1ppm (one millionth) and above is used for this product. But the pixels of RED,
GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels
could be seen. This is not from bad quality and you can use it without any problems.
•
For example, the number of TFT-LCD sub pixels contained in this product are
3,932,160.
When cleaning the monitor and the panel outside, please apply the recommended small
amount of cleaner by using a soft cloth to polish. Do not force the LCD area but rub softly.
If excessive force is applied, you may stain it.
If you are not satisfied with the picture quality, you can get better quality of picture by
performing the "Auto Adjustment function" in display screen that is appeared as window
termination button is pressed.
If there's still noise after the automatic adjustment, use the Fine/Coarse adjustment func-
tion.
When viewing a fixed screen for an extended period of time, a residual image or blur-
riness may appear.
Change the mode to energy save or set a screensaver to move the picture when you need
to be away from the monitor for an extended period of time.
PRODUCT INFORMATION (Image Retention Free)
LCD Monitors and TVs may have image retention when switching from one image to another espe-
cially after displaying a stationary image for a long time.
This guide is to demonstrate correct usage of LCD products in order to protect them from Image
retention.
Warranty
Warranty does not cover any damage caused by image retention.
Burn-in is not covered by the warranty.
What is Image retention ?
During normal operation of a LCD panel, pixel image retention doesn't occur. However, if
the same image is displayed for a long time, a slight difference in electric charge accumu-
lates between the two electrodes which encase the liquid crystal. This may cause the liquid
crystal to build up in a certain areas of the display. Thus, the previous image is retained
63
Information
when switching to a new video image. All display products, including LCD, are subject to
image retention. This is not a product defect.
Please follow the suggestions below to protect your LCD from image retention.
Power Off, Screen Saver, or Power Save Mode
Ex)
•
Turn the power off when using a stationary pattern.
•
•
Turn the power off for 4 hours after 20 hours in use
Turn the power off for 2 hours after 12 hours in use
•
•
Use a Screen saver if possible
Screen saver in one color or a moving image is recommended.
•
Set the Monitor to power off with the PC Display Properties Power Scheme.
Suggestions for specific applications
Ex) Airports, Transit Stations, Stock Markets, Banks, and Controlling Systems We recom-
mend that you follow set up of your display system program as below:
Display Information together with Logo or Moving image cycle.
Ex) Cycle : Display Information for 1 hour followed by a Display Logo or moving image
for 1 minute.
Change the Color Information periodically (Use 2 different colors).
Ex) Rotate the Color Information with 2 colors every 30 minutes.
Avoid using a combination of characters and background color with large difference in
luminance.
Avoid using Grey colors, which can cause Image retention easily.
•
Avoid: Colors with big difference in luminance (Black & White, Grey)
Ex)
•
Recommended settings: Bright colors with little difference in luminance
•
Change the characters color and background color every 30 minutes
64
Information
Ex)
•
Every 30 minutes, change the characters with movement.
Ex)
The best way to protect your monitor from Image retention is to set your PC or System
to operate a Screen Saver program when you are not using it.
Image retention may not occur when a LCD panel is operated under normal conditions.
Normal conditions are defined as continuously changing video patterns. When the LCD
panel is operated for a long time with a fixed pattern (-over 12 hours-), there may be slight
difference in voltage between electrodes that work the liquid crystal (LC) in a pixel. The
voltage difference between electrodes increases with time, forcing the liquid crystal to lean.
When this occurs, the previous image may be seen when the pattern is changed.
To prevent this, the accumulated voltage difference must be decreased.
65
Information
Our LCD Monitor satisfies ISO13406-2 Pixel fault Class II
66
Appendix
Contact SAMSUNG WORLDWIDE
Note
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG
customer care center.
North America
U.S.A
1-800-SAMSUNG(726-7864) http://www.samsung.com/us
1-800-SAMSUNG(726-7864) http://www.samsung.com/ca
01-800-SAMSUNG(726-7864) http://www.samsung.com/mx
CANADA
MEXICO
Latin America
ARGENTINE
BRAZIL
0800-333-3733
0800-124-421
4004-0000
CHILE
800-SAMSUNG(726-7864)
01 8000 112 112
0-800-507-7267
1-800-10-7267
800-6225
COLOMBIA
COSTA RICA
ECUADOR
EL SALVADOR
GUATEMALA
JAMAICA
1-800-299-0013
1-800-234-7267
800-7267
PANAMA
PUERTO RICO
REP. DOMINICA
1-800-682-3180
1-800-751-2676
BAGO
VENEZUELA
1-800-100-5303
Europe
AUSTRIA
BELGIUM
0800-SAMSUNG(726-7864)
0032 (0)2 201 24 18
CZECH REPUBLIC 844 000 844
DENMARK
FINLAND
FRANCE
70 70 19 70
030-6227 515
3260 SAMSUNG(726-7864)
08 25 08 65 65 (€ 0,15/Min)
GERMANY
HUNGARY
01805 - SAMSUNG(726-7864) http://www.samsung.de
(€ 0,14/Min)
06-80-SAMSUNG(726-7864) http://www.samsung.com/hu
67
Appendix
Europe
800-SAMSUNG(726-7864)
0035 (0)2 261 03 710
ITALIA
LUXEMBURG
NETHERLANDS
0900 SAMSUNG(726-7864) (€ http://www.samsung.com/nl
0,10/Min)
NORWAY
POLAND
815-56 480
0 801 801 881
022-607-93-33
80 8 200 128
PORTUGAL
REPUBLIC OF IRE- 0818 717 100
LAND
SLOVAKIA
SPAIN
0800-SAMSUNG(726-7864)
902 10 11 30
SWEDEN
SWITZERLAND
U.K
0771-400 200
0800-SAMSUNG(726-7864)
0870-SAMSUNG(726-7864)
CIS
800-7267
ESTONIA
LATVIA
800-7267
LITHUANIA
KAZAKHSTAN
KYRGYZSTAN
RUSSIA
8-800-77777
8-10-800-500-55-500
00-800-500-55-500
8-800-555-55-55
8-800-502-0000
8-800-120-0-400
UKRAINE
UZBEKISTAN
Asia Pacific
1300 362 603
AUSTRALIA
CHINA
800-810-5858
010-6475 1880
3698 - 4698
3030 8282
HONG KONG
INDIA
1800 110011
INDONESIA
JAPAN
0800-112-8888
0120-327-527
MALAYSIA
NEW ZEALAND
PHILIPPINES
SINGAPORE
THAILAND
TAIWAN
1800-88-9999
0800 SAMSUNG(726-7864)
1800-10-SAMSUNG(726-7864) http://www.samsung.com/ph
1800-SAMSUNG(726-7864)
1800-29-3232, 02-689-3232
0800-329-999
VIETNAM
1 800 588 889
68
Appendix
Middle East & Africa
0860-SAMSUNG(726-7864)
444 77 11
SOUTH AFRICA
TURKEY
U.A.E
800-SAMSUNG(726-7864)
8000-4726
Terms
Dot Pitch
The image on a monitor is composed of red, green and blue dots.
The closer the dots, the higher the resolution. The distance be-
tween two dots of the same color is called the 'Dot Pitch'. Unit:
mm
Vertical Frequency
The screen must be redrawn several times per second in order to
create and display an image for the user. The frequency of this
repetition per second is called the Vertical Frequency or Refresh
Rate. Unit: Hz
Example: If the same light repeats itself 60 times per second, this
is regarded as 60 Hz.
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge
of the screen horizontally is called the Horizontal Cycle. The in-
verse number of the Horizontal Cycle is called Horizontal Fre-
quency. Unit: kHz
Interlace and Non-Interlace
Methods
Showing the horizontal lines of the screen from the top to the bot-
tom sequentially is called the Non-Interlace method while show-
ing odd lines and then even lines in turn is called the Interlace
method. The Non-Interlace method is used for the majority of
monitors to ensure a clear image. The Interlace method is the same
as that used in TVs.
Plug & Play
Resolution
This is a function that provides the best quality screen for the user
by allowing the computer and the monitor to exchange informa-
tion automatically. This monitor follows the international standard
VESA DDC for the Plug & Play function.
The number of horizontal and vertical dots used to compose the
screen image is called the 'resolution'. This number shows the ac-
curacy of the display. A high resolution is good for performing
multiple tasks as more image information can be shown on the
screen.
Example: If the resolution is 1280 x 1024 , this means the screen
is composed of 1280 horizontal dots (horizontal resolution) and
1024 vertical lines (vertical resolution).
69
Appendix
Correct Disposal
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) -
Europe only
(Applicable in the European Union and other European
countries with separate collection systems)
This marking shown on the product or its literature, indi-
cates that it should not be disposed with other household
wastes at the end of its working life. To prevent possible
harm to the environment or human health from uncontrol-
led waste disposal, please separate this from other types of
wastes and recycle it responsibly to promote the sustaina-
ble reuse of material resources.
Household users should contact either the retailer where
they purchased this product, or their local government of-
fice, for details of where and how they can take this item
for environmentally safe recycling.
Business users should contact their supplier and check the
terms and conditions of the purchase contract. This prod-
uct should not be mixed with other commercial wastes for
disposal.
Authority
Information in this document is subject to change without notice.
© 2007 Samsung Electronics Co., Ltd. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co.,
Ltd. is strictly forbidden.
Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or con-
sequential damages in connection with the furnishing, performance, or use of this material.
Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and Win-
dows NT are registered trademarks of Microsoft Corporation; VESA, DPM and DDC are registered
trademarks of Video Electronics Standard Association; the ENERGY STAR® name and logo are reg-
istered trademarks of the U.S. Environmental Protection Agency (EPA). As an ENERGY STAR®
Partner, Samsung Electronics Co., Ltd. has determined that this product meets the ENERGY
STAR® guidelines for energy efficiency. All other product names mentioned herein may be the trade-
marks or registered trademarks of their respective owners.
70
|
