INSTALLATION, OPERATING AND
SERVICE INSTRUCTIONS FOR
INDEPENDENCE®
GAS - FIRED BOILER
For service or repairs to boiler, call your heating contractor. When seeking information on boiler,
provide Boiler Model Number and Serial Number as shown on Rating Label.
Boiler Serial Number
Installation Date
Boiler Model Number
IN
Heating Contractor
Phone Number
Address
8141049R26-10/08
Price - $5.00
CAUTION
Probe type low water cutoff devices require annual inspection and maintenance! Although these devices are
solid state in their operation, the probe is exposed to possible contamination in the boiler water and subject
to fouling. Refer to Low Water Cutoff Service Instructions for complete, step-by-step inspection and cleaning
instructions.
WARNING
This boiler requires regular maintenance and service to operate safely. Follow the instructions contained
in this manual.
Improperinstallation,adjustment,alteration,serviceormaintenancecancausepropertydamage,personal
injury or loss of life. Read and understand the entire manual before attempting installation, start-up
operation, or service. Installation and service must be performed only by an experienced, skilled, and
knowledgeable installer or service agency.
This boiler must be properly vented.
This boiler needs fresh air for safe operation and must be installed so there are provisions for adequate
combustion and ventilation air.
The interior of the venting system must be inspected and cleaned before the start of the heating season
and should be inspected periodically throughout the heating season for any obstructions. A clean and
unobstructed venting system is necessary to allow noxious fumes that could cause injury or loss of life
to vent safely and will contribute toward maintaining the boiler’s efficiency.
Installation is not complete unless a safety (relief) valve is installed. See the Piping and Trim Section of
this manual for details.
This boiler is supplied with safety devices which may cause the boiler to shut down and not re-start
without service. If damage due to frozen pipes is a possibility, the heating system should not be left
unattended in cold weather; or appropriate safeguards and alarms should be installed on the heating
system to prevent damage if the boiler is inoperative.
This boiler contains very hot water or steam under high pressure. Do not unscrew any pipe fittings nor
attempt to disconnect any components of this boiler without positively assuring the water is cool and has
no pressure. Always wear protective clothing and equipment when installing, starting up or servicing
this boiler to prevent scald injuries. Do not rely on the pressure and temperature gauges to determine
the pressure and temperature of the boiler. This boiler contains components which become very hot
when the boiler is operating. Do not touch any components unless they are cool.
Boilermaterialsofconstruction,productsofcombustionandthefuelcontainalumina,silica,heavymetals,
carbon monoxide, nitrogen oxides, aldehydes and/or other toxic or harmful substances which can cause
death or serious injury and which are known to the state of California to cause cancer, birth defects and
other reproductive harm. Always use proper safety clothing, respirators and equipment when servicing
or working nearby the appliance.
Failuretofollowallinstructionsintheproperordercancausepersonalinjuryordeath. Readallinstructions,
including all those contained in component manufacturers manuals which are provided with the boiler
before installing, starting up, operating, maintaining or servicing.
Keep boiler area clear and free from combustible materials, gasoline and other flammable vapors or
liquids.
All cover plates, enclosures and guards must be in place at all times.
ꢀ
4
Dimensional Data
Dimensions (in inches)
Recommended
Min. Round
Chimney Size
(Diameter x Height) (NPT)
(1)
Water Volume (Gal.)
Approx.
Gas
Conn.
Boiler
Model
Shipping
Weight
Lbs.
Steam Water
(3)
'A'
'B'
'C'
'D'
'E'
'F'
'G'
Boiler Boiler
IN3
IN4
350
420
485
14-1/2
17-3/4
21
33-3/4
34-3/4
4
5
7-1/4
8-7/8
4" x 15 ft.
5" x 15 ft.
5.1
6.5
7.9
7.8
3.9
5.0
6.1
4-3/4
5-1/4
10.0
12.2
IN5
10-1/2
1/2"
3/4"
35-3/4
6
6" x 15 ft.
IN6 USA
555
620
690
760
24-1/4
27-1/2
30-3/4
34
12-1/8
13-3/4
15-3/8
17
9.3
14.4
16.6
18.8
21.0
7.2
8.3
IN6
Canada
40-1/4
40
36-3/4
7
7" x 15 ft.
IN7
10.7
12.1
13.5
IN8 USA
9.4
IN8
Canada
37-3/4
IN9
8
8" x 15 ft.
9" x 15 ft.
10.5
7-1/2
IN10
USA
815
37-1/4
18-5/8
14.9
23.2
11.6
3/4"
(2)
IN10
Canada
45 38-3/4
45-1/2
9
IN11
IN12
885
40-1/2
43-3/4
20-1/4
21-7/8
16.3
17.7
25.4
27.6
12.7
13.8
955
1"
(1) 15' chimney height is from bottom of Draft Hood opening to top of Chimney.
(2) Gas connection size on IN10-IN11 Continuous Ignition (Standing Pilot) is 1 NPT.
(3) Steam boiler's "steamable water volume": water volume from NWL (normal water level) to low water cutoff level.
Heating Surface: 4.35 sq. ft. per flueway (steam); 5.72 sq. ft. per flueway (water)
Table of Contents
I. Pre-Installation.....................................7
II. Knockdown Boiler Assembly................9
III. Semi-Pak Boiler Assembly..................13
IV. Packaged Boiler Assembly ..................15
V. Piping and Trim .................................16
VI. Gas Piping..........................................22
VII. Venting............................................... 24
VIII. Electrical............................................. 26
IX. System Start-up .................................. 50
X. Service Instructions ............................ 62
XI. Repair Parts........................................ 69
XII. Appendix
Low Water Cut Off (LWCO)............... 90
5
Figure 2: Section Tappings
Table 1: Trim and Control Installation in Section Tappings
Size
(NPT)
Steam Boiler with
Probe L.W.C.O.
Steam Boiler with
Float L.W.C.O.
Water Boiler with
Tankless Heater
Tapping
Water Boiler
A
B
2
Supply
Supply
Supply
Plug
Supply
Bush to ¼
Pressure Gauge
½
Plug
Plug
Nipple & ½ Union
Gauge, L.W.C.O. Street
Elbow, Syphon & Limit
Plug Lower Tapping Bush
to ¼ Upper Tapping
Press./Temp. Gauge
Plug Lower Tapping Bush to
¼ Upper Tapping
C
D
½
Gauge Glass
Return
Press./Temp. Gauge
Bush to 1½, 3" Npl, Elbow,
2" Npl, Circ. Flange,
Bush to 1½, 3" Npl, Elbow,
2" Npl, Circ. Flange,
2
Return
Gasket, Circulator Return
Gasket, Circulator Return
3" Nipple & Street Elbow 3" Nipple & Street Elbow
3" Nipple & Street Elbow
Safety Relief Valve
3" Nipple & Street Elbow
Safety Relief Valve
E
F
¾
2
Safety Relief Valve
Safety Relief Valve
Bush to ¾ Drain Valve
Bush to ¾ Drain Valve
Bush to ¾ Drain Valve and/or Bush to ¾ Drain Valve and/or
and/or Optional Return
and/or Optional Return
Optional Gravity Return
Optional Gravity Return
Optional Supply (IN3-6) Optional Supply (IN3-6)
Required Supply (IN7-12 Required Supply (IN7-12
Plug (IN3-12)
Optional Gravity Supply
Plug (IN3-12)
Optional Gravity Supply
G
H
2
Bush to ¼ &
Syphon Limit
Bush to ¼
Pressure Gauge
Well
Limit
Well
Limit
¾
J
¾
¾
Not Applicable
Not Applicable
Plug
Not Applicable
Plug
Tankless Heater
K
Low Water Cutoff
Plug
Factory Plugged
Surface Blow-Off
Factory Plugged
Surface Blow-Off
L
M
N
P
1
Factory Plugged
Factory Plugged
Factory Plugged
Factory Plugged
Factory Plugged
Factory Plugged
Factory Plugged
Factory Plugged
Factory Plugged
Alliance Return
Factory Plugged
Alliance Return
1¼
1¼
¾
Factory Plugged
Alliance Supply
Factory Plugged
Alliance Supply
Factory Plugged
Alliance Limit
Factory Plugged
Alliance Limit
6
I. Pre-Installation
WARNING
front. Additional clearance may be required on left side
if optional tankless heater is installed. Service
clearances may be reduced to minimum clearances to
combustible materials.
If you do not follow these instructions exactly,
a fire or explosion may result causing property
damage or personal injury.
E. Install boiler on level floor as close to chimney as
possible. For basementinstallation provide a solid base,
such as concrete, steel or masonry if floor is not level or
if water may be encountered on floor around boiler.
DANGER
F. Protect gas ignition system components from water
(dripping, spraying, rain, etc.) during boiler operation
and service (circulator replacement, control
replacement, etc.).
Do not install boiler where gasoline or other
flammable vapors or liquids, or sources of
hydrocarbons (i.e. bleaches, cleaners, chemicals,
sprays, paint removers, fabric softeners, etc.) are
used or stored.
G. Provide combustion and ventilation air in accordance
with applicable provisions of local building codes, or
the National Fuel Gas Code, NFPA 54/ANSI Z223.1,
Section 5.3, Air for Combustion and Ventilation; or
CAN/CSA B149.1 Installation Code.
NOTICE
Due to the low water content of the boiler, mis-
sizing of the boiler with regard to the heating
system load will result in excessive boiler cycling
and accelerated component failure. Burnham
DOES NOT warrant failures caused by mis-sized
boiler applications. DO NOT oversize the boiler
to the system.
WARNING
Adequate combustion and ventilation air must be
provided to assure proper combustion.
The following guideline is based on the National Fuel
Gas Code, NFPA 54/ANSI Z223.1.
1. Determine volume of space (boiler room). Rooms
communicating directly with space (through
openings not furnished with doors) are considered
part of space.
A. Inspect shipment carefully for any signs of damage. All
equipment is carefully manufactured, inspected and
packed. Our responsibility ceases upon delivery of
boiler to carrier in good condition. Any claim for
damage or shortage in shipment must be filed
immediately against carrier by consignee. No claims for
variances or shortages will be allowed by Boiler
Manufacturer, unless presented within sixty (60) days
after receipt of equipment.
Volume [ft³] = Length [ft] x Width [ft] x Height [ft]
2. Determine Total Input of all appliances in space.
Round result to nearest 1,000 Btu per hour (Btuh).
3. Determine type of space. Divide Volume by Total
Input.
a. If result is greater than or equal to 50 ft³ per
1,000 Btuh, space is considered an unconfined
space.
B. Installation must conform to the requirements of the
authority having jurisdiction. In the absence of such
requirements, installation must conform to the National
Fuel Gas Code, NFPA 54/ANSI Z223.1 and/or CAN/
CSA B149.1 Installation Codes. Where required by the
authority having jurisdiction, the installation must
conform to the Standard for Controls and Safety
Devices for Automatically Fired Boilers, ANSI/ASME
No. CSD-1.
b. If result is less than 50 ft³ per 1,000 Btuh, space
is considered a confined space.
4. Determine building type. A building of unusually
tight construction has the following characteristics:
a. Walls and ceiling exposed to outside atmosphere
have a continuous water vapor retarder with a
rating of 1 perm or less with openings gasketed
and sealed, and
C. Appliance is design certified for installation on
combustible flooring. Boiler must not be installed on
carpeting.
b. Weather-stripping has been added on openable
windows and doors, and
D. Provide clearance between boiler jacket and
combustiblematerial in accordance with local fire
ordinance. See Figure 3 for minimum listed clearance
to combustible material. Recommended service
clearance is 24 inches from left side, right side, and
c. Caulking or sealants applied in joints around
window and door frames, between sole plates
and floors, between wall-ceiling joints, between
wall panels, at plumbing and electrical
penetrations, and at other openings.
ꢁ
Figure ꢀ: Clearance to Combustible Materials
5. For boiler located in an unconfined space in a
Alternate method for boiler located within confined
space. Use indoor air if two permanent openings
communicate directly with additional space(s) of
sufficient volume such that combined volume of all
spaces meet criteria for unconfined space. Size each
opening for minimum free area of 1 square inch per
1,000 Btu per hour input of all equipment in spaces,
but not less than 100 square inches.
building of other than unusually tight construction,
adequate combustion and ventilation air is normally
provided by fresh air infiltration through cracks
around windows and doors.
6. For boiler located within unconfined space in
building of unusually tight construction or within
confined space, provide outdoor air through two
permanent openings which communicate directly or
by duct with the outdoors or spaces (crawl or attic)
freely communicating with the outdoors. Locate one
opening within 12 inches of top of space. Locate
remaining opening within 12 inches of bottom of
space. Minimum dimension of air opening is 3
inches. Size each opening per following:
7. Ventilation Duct Louvers and Grilles. Equip outside
openings with louvers to prevent entrance of rain
and snow, and screens to prevent entrance of insects
and rodents. Louvers and grilles must be fixed in
open position or interlocked with equipment to open
automatically before burner operation. Screens must
not be smaller than ¼ inch mesh.
a. Direct communication with outdoors. Minimum
free area of 1 square inch per 4,000 Btu per hour
input of all equipment in space.
Consider the blocking effect of louvers, grilles and
screens when calculating the opening size to provide
the required free area. If free area of louver or grille
is not known, assume wood louvers have 20-25
percent free area and metal louvers and grilles have
60-75 percent free area.
b. Vertical ducts. Minimum free area of 1 square
inch per 4,000 Btu per hour input of all
equipment in space. Duct cross-sectional area
shall be same as opening free area.
H. Do not install boiler where gasoline or other flammable
vapors or liquids, or sources of hydrocarbons (i.e.
bleaches, cleaners, chemicals, sprays, paint removers,
fabric softeners, etc.) are used or stored.
c. Horizontal ducts. Minimum free area of 1 square
inch per 2,000 Btu per hour input of all
equipment in space. Duct cross-sectional area
shall be same as opening free area.
8
II. Knocked-Down Boiler Assembly
4. Loosen nuts on tie rods until only finger tight.
WARNING
5. If Steam boiler or Water boiler less tankless heater,
proceed to Step C.
Installation of this boiler should be undertaken
only by trained and skilled personnel from a
qualified service agency.
6. Water Boiler with tankless heater. Remove heater
opening cover plate and install tankless heater as
follows:
A. Install Base-Burner-Manifold Assembly
a. Place rubber gasket over heater coil and against
heater plate. Align holes in plate and gasket.
1. Base-Burner-Manifold is shipped assembled from
factory (Gas Valve and Pilot/Burner Assembly is
shipped in the "Gas Controls Carton").
b. Install water heater coil through opening into top
nipple ports of boiler and fasten with 3/8" hex
head machine screws and flat washers.
2. Unpack base assembly and place in location where
boiler is to be installed (Refer to Section I: Pre-
Installation).
Note: If tankless heater is not installed, heater
opening cover plate must remain in place.
C. Test boiler for leaks before connecting to system and
B. Install assembled cast iron sections on base assembly:
installing controls, trim and jacket.
1. Install (4) 5/16" x ¼" self-tapping screws through
(4) holes in upper base flange with screw heads on
underside of flange. Note: Screws are located in
fiber gasket parts bag.
1. Attach pressure gauge (capable of indicating 30 psi)
on boiler.
2. Attach fill valve and piping to return tapping and
purge valve to supply tapping. See Figure 6.
2. Install ceramic fiber gasket. See Figure 4.
Figure 4: Base Gasket Installation
3. Position boiler above base with lugs cast in boiler
sections centered over screws protruding from top of
base. Lower boiler onto base taking care not to
disturb ceramic fiber gasket. Secure with 5/16"
locknuts and washers provided. See Figure 5.
Figure 6: Hydrostatic Pressure Test
3. Install plugs in remaining tappings.
4. Fill boiler completely with water by venting air
through purge valve. Close purge valve and apply
water pressure of at least 10 psi but not exceeding
30 psi gauge pressure.
5. Examine boiler carefully inside and outside for leaks
or damage due to shipment or handling.
Figure 5: Section Assembly Attachment
9
3. Attach canopy using ¼" carriage bolts, nuts, and
washers provided.
D. Install Canopy.
1. Install ½" thick x 1" wide ceramic fiber gasket. See
Figure 7.
E. Inspect joints between sections. They were factory
sealed. If there are any openings due to shipment or
handling, reseal with boiler putty.
F. Install Jacket. See Figure 9.
1. Models IN7-IN12 steam boilers: remove 3 inch
diameter knockouts in jacket top panels.
2. Raise rear panel under rear flange of canopy and rest
on floor. Position rear panel and secure to jacket side
panels with sheet metal screws. For Models IN10-
IN12, secure jacket upper rear panels to side panels
with sheet metal screws.
3. Secure bothjacket side panels to base with sheet
metal screws.
Figure 7: Canopy Gasket Installation
4. Position front tie bar and secure to jacket side panels
with sheet metal screws.
2. Position canopy on ceramic fiber gasket. See Figure
8.
5. Positionvestibule panel and secure to side panels
with sheet metal screws.
6. Attach Rating Label and Vent Damper Instruction
Label at designated locations on vestibule panel.
7. Install top panels by placing over and around outside
of side and rear panels. Seat fully and secure with
sheet metal screws.
8. Install black plastic rings into 1-3/32 inch diameter
holes located below upper louvers of front
removable door.
Figure 8: Canopy Installation
Figure 9: Jacket Assembly
10
9. Install front removable door by engaging upper side
edges of panel with side receiving flanges, sliding
up and under top panel flange - seating front door
fully - then sliding down to engage bottom flange
behind lower front tie bar.
G. Install Pilot/Burner Assembly (shipped in Gas
Controls Carton). See Figure 10.
Figure 12: Pilot and Gas Piping, Continuous Ignition
(Standing Pilot) (IN10 through IN12 Only)
Figure 10: Combustion Chamber
1. Remove jacket front removable door.
a. Remove burner access panel located above
burners.
b. Install Pilot/Burner Assembly where noted on
gas manifold.
i. Insert rear of burner in burner tray slot.
ii. Position burner over the orifice.
NOTE: The burner to the right may need to
be lifted from the orifice to install pilot/
burner assembly. Reinstall lifted burner
over the orifice.
c. Reinstall burner access panel.
H. Install Gas Valve on main gas burner assembly (if not
factory assembled). See Figure 11, 12, 13, or 14.
Figure 1ꢀ: Pilot and Gas Piping, Intermittent Ignition
(EI) (INꢀ through IN11 Only)
1. Connect gas valve to manifold.
2. Connect pilot tubing from pilot burner to gas valve
pilot tapping.
3. Continuous Ignition (standing pilot): connect
thermocouple to gas valve.
Figure 11: Pilot and Gas Piping, Continuous
Ignition (Standing Pilot) (INꢀ through IN9 Only)
Figure 14: Pilot and Gas Piping, Intermittent Ignition
(EI) (IN12 Only)
11
I. Install Blocked Vent Switch with sheet metal screws.
1. Models IN3 - IN9. Install on rear flange of canopy.
See Figure 15.
Figure 16: Blocked Vent Switch Installation,
IN10 through IN12
5. Insert harness through ¾ inch hole in right side
jacket panel. Secure with strain relief bushing
J. Intermittent Ignition (EI): Install Ignition Module.
Figure 15: Blocked Vent Switch Installation,
1. Mount ignition module mounting bracket to inside
of right side panel using (2) #6 x ¾" sheet metal
screws provided.
INꢀ through IN9
2. Models IN10 - IN12. Install on right side of draft
hood. See Figure 16. Reset switch must face away
from draft hood relief opening.
2. Mount ignition module to bracket using (2) #8 x ½"
sheet metal screws provided.
3. Install (3) wire harness from ignition module to gas
valve as shown in wiring diagrams.
3. Attach black 18-2 harness to Blocked Vent Switch
terminals. Use end with two fully insulated
disconnects.
K. Continue to Section III: Semi-Pak Boiler Assembly,
Step C.
4. Secure harness to right side jacket panel with clamp.
12
III. Semi-PakBoiler Assembly
b. The L404F pressure limit employs a snap action
switch and does not require leveling. See Figure
18.
c. Install pressure gauge into Tapping "B" (½ NPT
bushed to ¼ NPT). See Figures 1 and 2. Tighten
with wrench applied to square shank on back of
gauge. DO NOT APPLY PRESSURE ON
GAUGE CASE since this may destroy
calibration of gauge.
d. Install Low Water Cutoff Probe into Tapping "K"
(¾ NPT). HANDLE PROBE WITH CARE.
e. Attach Low Water cutoff Control to Probe by
following instructions packed with control.
WARNING
Installation of this boiler should be undertaken
only by trained and skilled personnel from a
qualified service agency.
A. Remove Crate
1. Remove all hold down screws and brackets.
2. Slide boiler to rear of skid and carefully remove
from crate skid onto 2 inch thickpiece of wood and
then onto floor. Do not bump boiler jacket against
floor.
3. Do not drop boiler at any time.
f. Install gauge glass fittings into Tappings "C"
(½ NPT). See Figures 1 and 2. Lower fitting has
small drain valve.
g. Install gauge glass and protective rods in fittings.
h. Attach "Lowest Permissible Water Level" Plate
with sheet metal screws in location indicated in
Figure 9.
B. Move Boiler To Permanent Position. Refer to Section
I: Pre-Installation.
C. Identify Trim and Controls
FIRST - Determine controls ordered with boiler and
refer to appropriate section(s) following:
There are two ordering methods for trim and controls:
1. EZ–Connect Carton (either steam or water) includes
trim, controls, wiring and wiring instructions for
installation.
i. Attach "Frequent Water Addition" Label above
the "Lowest Permissible Water Level" Plate.
2. Steam Boiler with McDonnell & Miller 67 Float
2. Separate Trim Carton (steam or water) and Control
Carton (steam or water). Only wiring requiring
special connections is provided. For wiring
requirements, refer to Section VIII: Electrical and
appropriate wiring diagram.
Low Water Cutoff
a. Install Low Water Cutoff, see instructions packed
with control.
i. Screw brass nipples with union halves into
Tappings "C" (½ NPT). See Figure 1 and 2.
ii. Attach Gauge Glass/Low Water Cutoff
Assembly to union halves.
iii. Affix Blow-Down Card to Jacket Left Side
Panel adjacent to low water cutoff.
D. Install Trim and Controls
Refer to appropriate paragraphs (following) for trim
and controls to be installed.
1. Steam Boiler with Probe Low Water Cutoff
iv. Provide blow down discharge piping.
a. Install pressure limit control into Tapping "H"
with siphon, ¾" x ¼" hex bushing, ¾" elbow and
¾" x 3" nipple provided. See Figures 1 and 2.
DO NOT TWIST CONTROL. Use wrench on
hex fitting located at bottom of control. See
Figure 18.
b. Attach street elbow siphon and pressure limit
control to low water cutoff. DO NOT TWIST
CONTROL. Use wrench on hex fitting located at
bottom of control.
c. The L404F pressure limit employs a snap action
switch and does not require leveling. See Figure
18.
d. Install pressure gauge into Tapping "H" (¾ NPT
bushed to ¼ NPT). See Figures 1 and 2. Tighten
with wrench applied to square shank on back of
gauge. DO NOT APPLY PRESSURE ON
GAUGE CASE since this may destroy
calibration of gauge.
e. Attach "Lowest Permissible Water Level" Plate
with sheet metal screws in location indicated in
Figure 9.
f. Attach "Frequent Water Addition" Label above
the "Lowest Permissible Water Level" Plate.
Figure 18: L404F Pressure Limit Control
1ꢀ
3. All Steam Boilers and Water Boilers except
b. Install hot water temperature limit and/or
combination control. Remove well from control.
Screw well into Tapping "H" (¾ NPT). See
Figure 1 and 2. Install bulb in well as far as
possible, then tighten set screw.
"EZW" and "WC" Controls Cartons
a. Install Junction Box. See Figure 19A.
i. Remove center knockout in rear of Junction
Box and insert black plastic snap bushing in
hole.
c. On boilers equipped with a circulator without
tankless heater in areas where condensation of
flue gases is encountered in boiler flueways, a
reverse-acting circulator control should be
installed in supply as close as possible to boiler
in order to avoid condensation.
ii. Install mounting bracket to rear of Junction
Box with two (2) blunt sheet metal screws
provided.
iii. Align center and mounting holes of Junction
Box with upper front corner of jacket left
side panel.
E. Continue to Section IV. Packaged Boiler Assembly,
Paragraph E.
iv. Install Junction Box to jacket from inside
vestibule area with two (2) blunt sheet metal
screws provided.
b. Mount transformer on Junction Box. For
Canadian boiler provide strain relief by loosely
securing Transformer to Junction Box with wire
tie inserted through Transformer plate and a
Junction Box mounting hole. See Figure 19B.
c. Fork connector on yellow wire of gas valve
harness must be removed and wire stripped
before making wire connections. Refer to
Section VIII for wiring.
d. Steam Boilers only. Secure the R8222
Thermostat Isolation Relay to upperleft corner of
jacket vestibule panel with sheet metal screws
provided. See Figure 20.
e. Water with tankless heater only (EZWT and
WCT). Secure R8225D relay to Junction Box.
See Figure 1.
Figure 19B: Junction Box and Transformer
4. Water Boiler
Assembly
a. Install Temperature/Pressure Gauge into upper
Tapping "C" (½ NPT bushed to ¼ NPT). See
Figure 1 and 2. Tighten by wrench applied to
square shank on back of gauge. DO NOT
APPLY PRESSURE ON GAUGE CASE since
this may destroy calibration of gauge.
Figure 20: Thermostat Isolation Relay Attachment
Figure 19A: Junction Box and Mounting Bracket
Assembly
14
IV. Packaged Boiler Assembly
E. Install Jacket Front Panel.
WARNING
F. Install Draft Hood. Models IN3 through IN9.
Installation of this boiler should be undertaken
only by trained and skilled personnel from a
qualified service agency.
1. Locate and open "Rear Draft Hood Carton".
2. Position Draft Hood on Canopy Rear Flange. See
Figure 21. Top canopy flange must fully engage
"U"-shaped draft hood flange for proper installation
and operation. Care must be taken to assure that
draft hood is level.
A. Remove crate and move boiler to permanent position
as detailed in Section III: Semi-Pak Boiler Assembly.
B. Remove Jacket Front Panel. See Figure 45.
3. Secure Rear Draft Hood to Canopy with wing nuts
provided. See Figure 22.
C. Remove poly bag from vestibule area.
D. On Steam Boilers with probe low water cutoff the
L404 pressure limit/control has been packed in the
vestibule area.
1. Screw the pressure limit/control onto the syphon.
DO NOT TWIST CONTROL. Use wrench on hex
fitting at bottom of control. See Figure 18.
2. Snap the electrical conduit from the adjacent
junction box into the hole in the control.
3. Open the control's clear cover and attach the two (2)
wires in the conduit to the two (2) unused screw
terminals.
Figure 22: Securing Draft Hood to Canopy
WARNING
Do not alter boiler draft hood or place any
obstruction or non-approved damper in the
breeching or vent system. Flue gas spillage can
occur. ETL/ETLC certification will become void.
Figure 21: Draft Hood Attachment
15
V. Piping and Trim
WARNING
Failure to properly pipe boiler may result in improper operation and damage to boiler or structure.
A. Design and install boiler and system piping to prevent
WARNING
oxygen contamination of boiler water. Sources of
oxygen contamination are system leaks requiring
addition of makeup water, fittings, and oxygen
permeable materials in distribution system. Eliminate
oxygen contamination by repairing system leaks,
repairing fittings, using nonpermeable materials in
distribution system, and eliminating open tanks in
system, or isolating boiler from system with heat
Safety (relief) valve discharge piping must be
piped such that the potential of severe burns
is eliminated. DO NOT pipe in any area where
freezing could occur. DO NOT install any shut-off
valves, plugs or caps. Consult Local Codes for
proper discharge piping arrangement.
exchanger.
C. Install Drain Valve in Tapping "F" (2 NPT bushed to
B. Install Safety (Relief) Valve in Tapping "E" (¾ NPT).
See Figure 23. Use ¾ NPT x 3" nipple and ¾ NPT
elbow provided. Safety (Relief) Valve must be installed
with spindle in vertical position.
¾ NPT). See Figure 23.
D. Connect supply and return piping to heating system.
Maintain minimum ½ inch clearance from combustible
materials.
1. For STEAM HEATING see Figure 24. Consult
I=B=R Installation and Piping Guides.
2. For HOT WATER HEATING with Circulator
(forced) see Figure 25 and 25A. ConsultI=B=R
Installation and Piping Guides.
3. If boiler is used in connection with refrigeration
systems, boiler must be installed with chilled
medium piped in parallel with heating boiler using
appropriate valves to prevent the chilled medium
from entering the boiler. See Figure 26. Also
consult I=B=R Installation and Piping Guides.
4. If boiler is connected to heating coils located in air
handling units where they may be exposed to
refrigerated air, boiler piping must be equipped with
flow control valves to prevent gravity circulation of
boiler water during cooling system operation.
Figure 2ꢀ: Trim Installation
NOTICE
Do not use softened water in steam boilers. Accelerated boiler corrosion will result. Tie in fresh water
supply to the boiler upstream of a water softener.
Oxygen contamination of boiler water will cause corrosion of iron and steel boiler components, and
can lead to boiler failure. Burnham's Standard Warranty does not cover problems caused by oxygen
contamination of boiler water or scale (lime) build-up caused by frequent addition of water.
Before using copper for steam piping, consider the following characteristics of copper piping:
1) high coefficient of thermal expansion can induce mechanical stresses and cause expansion/
contraction noises if not accounted for in the piping system design and installation,
2) high heat transfer rate (heat loss) of uninsulated copper piping must be included in the normal
piping and pickup factors used to size the boiler,
3) soldering or brazing pastes and fluxes that end up in the system can cause poor heat transfer,
surging, an unsteady water line and wet steam if not thoroughly removed during the boil out
procedure and,
4) galvanic corrosion of the adjoining metal may occur due to dissimilar metals in certain water
chemistries if dielectric unions are not used.
16
1ꢁ
18
19
E. Alliance Indirect Water Heater (if used). Refer to
Alliance Installation, Operating and Service Instructions
for additional information.
1. Steam. See Figure 27 for piping recommendations.
a. Supply and Return Piping. Connect supply
piping to Tapping "N" (1¼ NPT) and return
piping to Tapping "M" (1¼ NPT). Install zone
circulator and strainer in supply piping. Install
check valve to prevent gravity circulation of
boiler water.
b. Limit. See Figure 23. Install temperature limit
control (Honeywell L4006A or equal) in Tapping
"P" (¾ NPT). See Figure 2. Set at 180°F to
prevent steam production during non-space
heating periods.
Figure 26: Recommended Piping for Combination
Heating and Cooling (Refrigeration) Systems
Figure 2ꢁ: Recommended Piping for
Indirect Water Heater
Figure 28: Tankless Heater Piping
5. Use boiler bypass if boiler is operated in system
which has a large volume or excessive radiation
where low boiler water temperatures may be
encountered (i.e. converted gravity circulation
system, etc.).
2. Water without tankless heater. Install in same
manner as space heating zone.
F. Tankless Heater (if used). See Figure 28.
1. Install automatic tempering or mixing valve to
prevent delivery of scalding hot water to fixtures.
Higher temperature water for dishwashers and
automatic washers is possible by piping hot water
from heater prior to entering mixing valve. Install
per manufacturer's instructions.
a. Bypass should be same size as supply and return
lines with valves located in bypass and supply
outlet as illustrated in Figures 25 and 25A in
order to regulate water flow to maintain higher
boiler water temperatures.
b. Set bypass and boiler supply valves to a half
throttle position to start.
WARNING
c. After installation is complete, operate boiler
according to Section IX: System Start-up.
Install automatic mixing valve at tankless heater
outlet to avoid risk of burns or scalding due to
excessively hot water at fixtures.
6. A hot water boiler installed above radiation level
must be provided with a low water cutoff device as
part of installation.
2. Install flow regulator. Match regulator rating to
tankless heater rating. Install in cold water inlet
below and minimum 3 feet downstream of tankless
heater inlet.
The low water cut off must be mounted in the
system piping above the boiler. The minimum safe
water level of a hot water boiler is just above the
highest water containing cavity of the boiler; that is,
a hot water boiler must be full of water to operate
safely (see XII. Appendix for further details) .
7. If a tankless heater coil is used, connect water lines
to ¾ NPT tappings in coil plate.
3. Install water softener in areas of hard water, this will
reduce mineral deposits which could hinder heat
transfer and delivery of hot water.
20
To perform a long term pressure test including the
boiler, ALL trapped air must first be removed from the
boiler.
G. If a long term pressure test of the hydronic system is
required, the boiler should first be isolated to avoid a
pressure loss due to the escape of air trapped in the
boiler.
A loss of pressure during such a test, with no visible
water leakage, is an indication that the boiler contained
trapped air.
21
VI. Gas Piping
WARNING
For materials or conditions other than those listed
above, refer to the National Fuel Gas Code, NFPA 54/
ANSI Z223.1 and/or CAN/CSA B149.1. Installation
Codes, or size system using standard engineering
methods acceptable to authority having jurisdiction.
Failure to properly pipe gas supply to boiler may
result in improper operation and damage to the
boiler or structure. Always assure gas piping is
absolutely leak free and of the proper size and
type for the connected load.
WARNING
An additional gas pressure regulator may be
needed. Consult gas supplier.
Failure to use proper thread compounds on all
gas connectors may result in leaks of flammable
gas.
A. Size gas Piping. Design system to provide adequate gas
supply to boiler. Consider these factors:
WARNING
1. Allowable pressure drop from point of delivery to
boiler. Maximum allowable system pressure is ½
psig. Actual point of delivery pressure may be less;
contact gas supplier for additional information.
Minimum gas valve inlet pressure is indicated on
Rating Label, located on the vestibule panel.
Gas supply to boiler and system must be
absolutely shut off prior to installing or servicing
boiler gas piping.
B. Connect boiler gas valve to gas supply system.
2. Maximum gas demand. Table 2 lists boiler input
rate. Also consider existing and expected future gas
utilization equipment (i.e. water heater, cooking
equipment).
1. Use methods and materials in accordance with local
plumbing codes and requirements of gas supplier. In
absence of such requirements, follow the National
Fuel Gas Code, NFPA 54/ANSI Z223.1 and/or
CAN/CSA B149.1 Installation Codes.
Table 2: Rated Input
2. Use thread (joint) compounds (pipe dope) resistant
to action of liquefied petroleum gas.
Boiler
Model
Number
Rated Capacity
[cubic feet per hour]
Gas
Connection
Size
3. Install sediment trap, ground-joint union and manual
shut-off valve upstream of boiler gas valve and
outside jacket. See Figure 29.
Natural
62
LP/Propane
IN3
IN4
24¾
42
½
½
½
½
¾
¾
¾
¾*
¾*
1
105
140
175
210
245
280
315
349
385
IN5
56
IN6
70
IN7
84
IN8
98
IN9
112
126
139½
154
IN10
IN11
IN12
* Gas connection size is 1" on IN10 and IN11
Continuous Ignition (Standing Pilot)
3. Length of piping and number of fittings. Refer to
Table 3 for maximum capacity of Schedule 40 pipe.
Table 4 lists equivalent length for standard fittings.
4. Corrections for the specific gravity of natural gas
can be found in Table 5.
Figure 29: Recommended Gas Piping
22
4. All above ground gas piping upstream from manual
gas valve must be electrically continuous and
bonded to a grounding electrode. Do not use gas
piping as a grounding electrode. Refer to the
National Electrical Code, ANSI/NFPA 70 and/or
CSA C22.1 Electrical Code.
½ psig or less, isolate boiler from gas supply piping
by closing boiler's individual manual shut-off valve.
2. Using soap solution, or similar non-combustible
solution, electronic leak detector or other approved
method. Check that boiler gas piping valves, and all
other components are leak free. Eliminate any
leaks.
C. Pressure Test. The boiler and its gas connection must
be leak tested before placing boiler in operation.
DANGER
1. Protect boiler gas valve. For all testing over ½ psig,
boiler an its individual shut-off valve must be
Doe not use matches, candles, open flames or
other ignition source to check for leaks.
disconnected from gas supply piping. For testing at
Table 3: Maximum Capacity of Schedule 40 Pipe in CFH for Natural Gas Pressures of 0.5 psig or Less
0.3 inch w.c. Pressure Drop
0.5 inch w.c. Pressure Drop
Length\
[Feet]
½
132
92
73
63
56
50
46
43
40
38
¾
278
190
152
130
115
105
96
1
1¼
1,050
730
590
500
440
400
370
350
320
305
½
175
120
97
¾
1
1¼
1,400
950
770
660
580
530
490
460
430
400
10
20
30
40
50
60
70
80
90
100
520
350
285
245
215
195
180
170
160
150
360
250
200
170
151
138
125
118
110
103
680
465
375
320
285
260
240
220
205
195
82
73
66
61
90
57
84
53
79
50
Table 5: Specific Gravity Correction Factors for
Natural Gas
Specific
Gravity
Correction
Factor
Specific
Gravity
Correction
Factor
Table 4: Fitting Equivalent Lengths
0.50
0.55
0.60
0.65
0.70
0.75
0.80
1.10
1.04
1.00
0.96
0.93
0.90
0.87
1.30
1.40
1.50
1.60
1.70
1.07
1.04
1.00
0.97
0.94
Nominal Pipe Size
Fitting
½
¾
1
1¼
1.6
3.5
45° Ell
90° Ell
0.7
1.6
1.0
2.1
1.2
2.6
Tee
(As Elbow)
3.1
4.1
5.2
6.9
NOTICE
USAboilers built for installation at altitudes greater than 2,000 feet above sea level have been specially orificed
to reduce gas input rate 4 percent per 1,000 feet above sea level per the National Fuel Gas Code, NFPA 54/
ANSI Z223.1. Canadian boilers' orifice sizing is indicated on the rating label. High altitude boiler models are
identifiable by the third digit in the model number suffix on the rating label:
_IN_ _ _ - _ _ 2 less than 2000 ft. elevation
_IN_ _ _ - _ _ 4 2000 to 4500 ft. elevation (Canada)
_IN_ _ _ - _ _ 5 2000 to 5000 ft. elevation (USA)
2ꢀ
VII. Venting
WARNING
This appliance needs fresh air for safe operation and must be installed so there are provisions for
adequate combustion and ventilation air.
Read, understand and follow combustion air instruction restrictions contained in the Pre-Installation
instructions of this manual.
Do not operate appliance where gasoline or other flammable vapors or liquids, or sources of
hydrocarbons (i.e. bleaches, cleaners, chemicals, sprays, paint removers, fabric softeners, etc.) are
used, stored and/or present in the air.
A. Install vent system in accordance with local building
codes; or local authority having jurisdiction; or
National Fuel Gas Code, ANSI Z223.1/NFPA 54, Part
7, Venting of Equipment and/or CAN/CSA B149.1
Installation Codes. Install any of the following for this
Independence Series Category I, draft hood equipped
appliance:
CAUTION
Do not use one vent damper to control two
heating appliances.
Provide adequate clearance for servicing -
6" minimum clearance between damper and
combustible construction.
1. Type B or Type L gas vent. Install in accordance
with listing and manufacturer's instructions.
2. Masonry or metal chimney. Build and install in
accordance with local building codes; or local
authority having jurisdiction; or Standard for
Chimneys, Fireplaces, Vents, and Solid Fuel
Burning Appliances, ANSI/NFPA 211 and/or
National Building Code of Canada.
NOTICE
DO NOT force the vent damper over the
rolled bead on the draft hood collar. The
vent damper should rest on the rolled bead.
Masonry chimney must be lined with approved clay
flue lining or listed chimney lining system except as
provided in ANSI Z223.1/NFPA 54, Paragraph
7.5.4(a): Exception: Where permitted by the
authority having jurisdiction, existing chimneys
shall be permitted to have their use continued when
an appliance is replaced by an appliance of similar
type, input rating, and efficiency.
Please refer to the specifications,
installation instructions and trouble
shooting guide packed in the vent damper
carton for complete detailed installation
instructions.
2. Vent damper should be same size as draft hood
outlet. See Figure 1. Unpack vent damper carefully
- DO NOT FORCE CLOSED! Forcing vent
damper may damage gear train and void warranty.
Vent damper assembly includes pre-wired
connection harness with polarized plug for use on
all 24V standing pilot or intermittent ignition (EI)
control systems.
3. Single wall metal vent. Allowed by ANSI Z223.1/
NFPA 54 under very restrictive conditions.
B. Inspect chimney and remove any obstructions or
restrictions. Clean chimney if previously used for solid
or liquid fuel-burning appliances or fireplaces.
DANGER
3. Mount vent damper assembly on draft hood without
modification to either (Refer to instructions packed
with vent damper for specific instructions). Vent
damper position indicator to be visible to users.
Inspect existing chimney before installing boiler.
Failure to clean or replace perforated pipe or tile
lining will cause severe injury or death.
4. USA - Do not install Non-listed vent damper or
other obstruction in vent pipe.
C. Boiler Equipped With Vent Damper
1. Open Vent Damper Carton and remove Installation
Instructions. Read Installation Instructions
thoroughly before proceeding.
Canada - Do not install Non-listed vent damper or
other obstruction in vent pipe.
24
3. Insofar as is practical, close all building doors and
windows and all doors between the space in which
the appliances remaining connected to the common
venting system are located and other spaces of the
building. Turn on clothes dryers and any appliance
not connected to the common venting system. Turn
on any exhaust fans, such as range-hoods and
bathroom exhausts, so they will operate at maximum
speed. Do not operate a summer exhaust fan. Close
fireplace dampers.
D. Install Vent Connector from draft hood or vent
damper to chimney. See Figure 30.
1. Do not connect into same leg of chimney serving an
open fireplace.
2. Vent pipe to chimney must not be smaller than outlet
on draft hood or vent damper. Type B is
recommended, but single-wall vent pipe may be
used. Arrange venting system so boiler is served by
vent damper device.
3. Where two or more appliances vent into a common
vent, the area of the common vent should be at least
equal to the area of the largest vent plus 50% of the
area in the additional vent(s). Do not connect the
vent of this appliance into any portion of mechanical
draft systems operating under positive pressure.
4. Place in operation the appliance being inspected.
Follow the Lighting (or Operating) Instructions.
Adjust thermostat so appliance will operate
continuously.
5. Test for spillage at the draft hood relief opening
after 5 minutes of main burner operation. Use the
flame of a match or candle, or smoke from a
cigarette, cigar or pipe.
4. Horizontal run should be as short as possible. The
maximum length of an uninsulated horizontal run
must not exceed 75% of the height of the chimney.
6. After it has been determined that each appliance
remaining connected to the common venting system
properly vents when tested as outlined above, return
doors, windows, exhaust fans, fireplace dampers and
any other gas-burning appliance to their previous
condition of use.
5. Vent pipe should have the greatest possible initial
rise above draft hood consistent with headroom
available and required clearance from adjacent
combustible building structure. Vent pipe should be
installed above bottom of chimney to prevent
blockage.
7. Any improper operation of the common venting
system should be corrected so the installation
conforms with the National Fuel Gas Code, NFPA
54/ANSI Z223.1. When resizing any portion of the
common venting system, the common venting
system should be resized to approach the minimum
size as determined using the appropriate tables in
Part 11 in the National Fuel Gas Code, NFPA 54/
ANSI Z223.1.
6. Vent pipe should slope upward from draft hood to
chimney not less than one inch in four feet. No
portion of vent pipe should run downward or have
dips or sags. Vent pipe must be securely supported.
7. Vent pipe must be inserted into but not beyond
inside wall of chimney liner. Seal tight between vent
pipe and chimney.
E. If an Existing Boiler is Removed:
When an existing boiler is removed from a common
venting system, the common venting system is likely to
be too large for proper venting of the appliances
remaining connected to it.
At the time of removal of an existing boiler, the
following steps shall be followed with each appliance
remaining connected to the common venting system
placed in operation, while the other appliances
remaining connected to the common venting system are
not in operation:
1. Seal any unused openings in the common venting
system.
2. Visually inspect the venting system for proper size
and horizontal pitch and determine there is no
blockage or restriction, leakage, corrosion, and other
deficiencies which could cause an unsafe condition.
Figure 30: Typical Vent Installation
25
VIII. Electrical
DANGER
Positively assure all electrical connections are unpowered before attempting installation or service of
electrical components or connections of the boiler or building. Lock out all electrical boxes with padlock
once power is turned off.
WARNING
Failure to properly wire electrical connections to the boiler may result in serious physical harm.
Electrical power may be from more than one source. Make sure all power is off before attempting any
electrical work.
Each boiler must be protected with a properly fused disconnect.
Never jump out or make inoperative any safety or operating controls.
A. General. Install wiring and ground boiler in accordance
with requirements of authority having jurisdiction, or in
absence of such requirements the National Electrical
Code, ANSI/NFPA 70 and/or CSA C22.1 Electrical
Code.
B. Wire Vent Damper (if used).
1. Steam or Water with gravity circulation or tankless
heater.
a. Remove one (1) 7/8" knockout from junction
box. Carefully remove transformer - avoid undue
strain on wires.
b. Install Vent Damper Harness into top of junction
box.
Figure 32: Vent Damper Harness to Junction Box
2. Water with intermittent circulation and without
tankless heater.
c. Remove factory installed jumper plug (if so
equipped) from Vent Damper Receptacle. Plug
Vent Damper Harness into Vent Damper
Receptacle. See Figure 31.
a. Remove 7/8" knockout and cover from limit
control.
b. Install Vent Damper Harness into top of limit.
c. Remove factory installed jumper plug from Vent
Damper Receptacle. Plug Vent Damper Harness
into Vent Damper Receptacle. See Figure 31.
d. Install cable clamp around flexible Vent Damper
Harness. Attach to jacket top panel. See Figure
33.
3. Note: After vent damper is installed and operated
through one (1) cycle, the control circuit will
operate only when vent damper is in control circuit.
C. Install thermostat. Locate on inside wall
approximately 4 feet above floor. Do not install on
outside wall, near fireplace, or where influenced by
drafts or restricted air flow, hot or cold pipes, lighting
fixtures, television, or sunlight. Allow free air
movement by avoiding placement of furniture near
thermostat.
Figure 31: Vent Damper Connection Detail
d. Install cable clamp around flexible Vent Damper
Harness. Attach to jacket top panel. See Figure
32.
26
Set heat anticipator to match system requirements. See
Table 6. In general, setting heat anticipator too low will
cause boiler to short cycle without bringing heated
space up to temperature. Setting heat anticipator too
high will allow boiler to operate longer than necessary
and overheat space.
1. A separate electrical circuit must be run from the
main electrical service with an over-current device/
disconnect in the circuit. A service switch is
recommended and may be required by some local
jurisdictions. Boiler is rated for 120 VAC, 60 hertz,
less than 12 amperes.
2. For zone valve wiring, provide separate 24V
transformer rather than attempting to use boiler
mounted control. Consult zone valve manufacturer
for assistance.
D. Wire thermostat. Provide Class II circuit between
thermostat and boiler.
1. Steam or Water with gravity circulation or tankless
heater. Remove transformer from junction box.
Connect one wire from thermostat to blue wire(s).
Connect additional wire from thermostat to brown
wire or red wire for water with tankless heater.
G. Wiring diagram and sequence of operation. Locate
the system type you are interested in from Table 6, then
refer to the page indicated.
1. Vent Damper Sequence of Operation. See Figure
34.
2. Water with intermittent circulation and without
tankless heater. Connect one wire from thermostat
to Terminal "T" and additional wire to terminal
"TV".
a. Vent Damper is continuously powered at
Terminal 1.
b. When there is a call for heat, the damper relay
coil is energized through Terminal 5 if all limits
ahead of the damper are satisfied.
E. Alliance Indirect Water Heater (if used).
1. For wiring refer to wiring diagrams located in this
section and Alliance Installation Operating and
Service Instructions.
c. Relay coil closes contacts, energizing damper
motor, causing damper to open.
2. Attach junction box extension (4 - 11/16 square) to
junction box on boiler.
d. When the damper blade reaches the fully open
position, power is sent back to the boiler limit/
ignition circuit through Terminal 2 and the
damper motor is de-energized.
3. Steam Boilers only. Verify temperature limit
(Honeywell L4006 or equal, which is installer
supplied) is installed in Tapping "P", refer to
Section V: Piping and Trim.
e. When the call for heat is satisfied, the damper
relay coil is de-energized—closing contacts
which energize the damper motor. This causes
the damper to close. When the damper blade
reaches the fully closed position, the damper
motor is de-energized.
F. Wire control circuit as shown in the appropriate
wiring diagram. See Table 6.
Table 6: Thermostat Heat Anticipator Settings
Ignition System
System Type
Heat Anticipator Setting (1)
Intermittent (EI)
Continuous (Standing Pilot)
Steam with Probe
(McDonnell & Miller PS-802 or
Hydrolevel CGB-400)
Low Water Cutoff
Figure 35, Page 30
Figure 36, Page 32
Figure 38, Page 36
0.8
0.8
Steam with Float
(McDonnell & Miller 67)
Low Water Cutoff
Figure 37, Page 34
Water (Intermittent Circulation)
Water (Gravity Circulation)
Water with Tankless Heater
Figure 39, Page 38
Figure 41, Page 42
Figure 43, Page 46
Figure 40, Page 40
Figure 42, Page 44
Figure 44, Page 48
0.3
0.3
0.6
(1) If system tends to overheat above thermostat's temperature setting, reduce heat anticipator setting by 0.1
or 0.2 amps. If system tends to shortcycle without reaching desired room temperature, increase heat
anticipator setting by 0.1 or 0.2 amps.
2ꢁ
Figure 33: Vent Damper Harness to Limit
Figure 34: Vent Damper Schematic Wiring Diagram
28
THIS PAGE LEFT INTENTIONALLY BLANK
29
ꢀ0
b. Low Water Cutoff (LWCO): Automatically
interrupts main burner operation when surface of
boiler water falls to lowest permissible operating
level. Normal operation resumes when water
returns to normal level.
H. Steam Boiler with Continuous Ignition (Standing Pilot)
and Probe Low Water Cutoff. See Figure 35.
1. Normal Operation
a. Thermostat calls for heat. Thermostat Isolation
Relay is energized, closing contacts.
c. Blocked Vent Switch. Automatically interrupts
main burner operation when excessive vent
system blockage occurs. Control is a multiple
use device. If blocked vent switch is activated do
not attempt to place boiler in operation. Correct
source of blockage and reset blocked vent
switch.
b. Vent Damper (if used) opens as stated in Vent
Damper Sequence of Operation.
c. Gas Valve(s) is energized allowing main gas flow
and ignition of Main Burners.
d. After Thermostat is satisfied Gas Valve(s) is de-
energized, extinguishing main flame. Vent
Damper (if used) closes.
d. Flame Roll-out Switch. Automatically interrupts
boiler operation when flames or excessive heat
are present in vestibule. Control is single use
device. If flame roll-out switch is activated do
not attempt to place boiler in operation. Correct
source of blockage and replace flame roll-out
switch.
2. Safety Shutdown
a. Limit: Automatically interrupts main burner
operation when steam pressure exceeds set point.
Maximum allowable pressure is 15 psi. Normal
operation resumes when system pressure falls
below set point.
e. Thermocouple: senses pilot flame and causes gas
valve to turn off main burner and pilot burner gas
flow should pilot burner flame extinguish.
ꢀ1
ꢀ2
level. Normal operation resumes when water
returns to normal level.
I. Steam Boiler with Intermittent Ignition (EI) and Probe
Low Water Cutoff. See Figure 36.
c. Blocked Vent Switch. Automatically interrupts
main burner operation when excessive vent
system blockage occurs. Control is a multiple
use device. If blocked vent switch is activated do
not attempt to place boiler in operation. Correct
source of blockage and reset blocked vent
switch.
1. Normal Operation
a. Thermostat calls for heat. Thermostat Isolation
Relay is energized, closing contacts.
b. Vent Damper (if used) opens as stated in Vent
Damper Sequence of Operation.
c. Ignition Module is energized. Pilot Valve opens
and Igniter is energized to ignite Pilot Burner.
d. Flame Roll-out Switch. Automatically interrupts
boiler operation when flames or excessive heat
are present in vestibule. Control is single use
device. If flame roll-out switch is activated do
not attempt to place boiler in operation. Correct
source of blockage and replace flame roll-out
switch.
d. Sensor proves presence of pilot flame. Main
Valve(s) opens and ignites Main Burners.
e. After Thermostat is satisfied Ignition Module is
de-energized, extinguishing pilot and main
flame. Vent Damper (if used) closes.
2. Safety Shutdown
e. Igniter/Sensor: senses pilot flame and causes
ignition module to turn off main burner and pilot
burner gas flow should pilot burner flame
a. Limit: Automatically interrupts main burner
operation when steam pressure exceeds set point.
Maximum allowable pressure is 15 psi. Normal
operation resumes when system pressure falls
below set point.
extinguish. Five to six minutes after shutdown,
Ignition Module restarts ignition sequence.
For Electronic Ignition Trouble Shooting Guide,
see Page 65. For LED Status Codes, see Tables
8 and 9 on pages 55 and 56.
b. Low Water Cutoff (LWCO): Automatically
interrupts main burner operation when surface of
boiler water falls to lowest permissible operating
ꢀꢀ
ꢀ4
b. Low Water Cutoff (LWCO): Automatically
interrupts main burner operation when surface of
boiler water falls to lowest permissible operating
level. Normal operation resumes when water
returns to normal level.
J. Steam Boiler with Continuous Ignition (Standing Pilot)
and Float Low Water Cutoff. See Figure 37.
1. Normal Operation
a. Thermostat calls for heat. Thermostat Isolation
Relay is energized, closing contacts.
c. Blocked Vent Switch. Automatically interrupts
main burner operation when excessive vent
system blockage occurs. Control is a multiple
use device. If blocked vent switch is activated do
not attempt to place boiler in operation. Correct
source of blockage and reset blocked vent
switch.
b. Vent Damper (if used) opens as stated in Vent
Damper Sequence of Operation.
c. Gas Valve(s) is energized allowing main gas flow
and ignition of Main Burners.
d. After Thermostat is satisfied Gas Valve(s) is de-
energized, extinguishing main flame. Vent
Damper (if used) closes.
d. Flame Roll-out Switch. Automatically interrupts
boiler operation when flames or excessive heat
are present in vestibule. Control is single use
device. If flame roll-out switch is activated do
not attempt to place boiler in operation. Correct
source of blockage and replace flame roll-out
switch.
2. Safety Shutdown
a. Limit: Automatically interrupts main burner
operation when steam pressure exceeds set point.
Maximum allowable pressure is 15 psi. Normal
operation resumes when system pressure falls
below set point.
e. Thermocouple: senses pilot flame and causes gas
valve to turn off main burner and pilot burner gas
flow should pilot burner flame extinguish.
ꢀ5
ꢀ6
level. Normal operation resumes when water
returns to normal level.
K. Steam Boiler with Intermittent Ignition (EI) and Float
Low Water Cutoff. See Figure 38.
c. Blocked Vent Switch. Automatically interrupts
main burner operation when excessive vent
system blockage occurs. Control is a multiple
use device. If blocked vent switch is activated do
not attempt to place boiler in operation. Correct
source of blockage and reset blocked vent
switch.
1. Normal Operation
a. Thermostat calls for heat. Thermostat Isolation
Relay is energized, closing contacts.
b. Vent Damper (if used) opens as stated in Vent
Damper Sequence of Operation.
c. Ignition Module is energized. Pilot Valve opens
and Igniter is energized to ignite Pilot Burner.
d. Flame Roll-out Switch. Automatically interrupts
boiler operation when flames or excessive heat
are present in vestibule. Control is single use
device. If flame roll-out switch is activated do
not attempt to place boiler in operation. Correct
source of blockage and replace flame roll-out
switch.
d. Sensor proves presence of pilot flame. Main
Valve(s) opens and ignites Main Burners.
e. After Thermostat is satisfied Ignition Module is
de-energized, extinguishing pilot and main
flame. Vent Damper (if used) closes.
2. Safety Shutdown
e. Igniter/Sensor: senses pilot flame and causes
ignition module to turn off main burner and pilot
burner gas flow should pilot burner flame
a. Limit: Automatically interrupts main burner
operation when steam pressure exceeds set point.
Maximum allowable pressure is 15 psi. Normal
operation resumes when system pressure falls
below set point.
extinguish. Five to six minutes after shutdown,
Ignition Module restarts ignition sequence.
For Electronic Ignition Trouble Shooting Guide,
see Page 65. For LED Status Codes, see Tables
8 and 9 on pages 55 and 56.
b. Low Water Cutoff (LWCO): Automatically
interrupts main burner operation when surface of
boiler water falls to lowest permissible operating
ꢀꢁ
ꢀ8
b. Blocked Vent Switch. Automatically interrupts
main burner operation when excessive vent
system blockage occurs. Control is a multiple
use device. If blocked vent switch is activated do
not attempt to place boiler in operation. Correct
source of blockage and reset blocked vent
switch.
L. Water Boiler with Continuous Ignition (Standing Pilot)
and Intermittent Circulation. See Figure 39.
1. Normal Operation
a. Thermostat calls for heat.
b. Vent Damper (if used) opens as stated in Vent
Damper Sequence of Operation.
c. Flame Roll-out Switch. Automatically interrupts
boiler operation when flames or excessive heat
are present in vestibule. Control is single use
device. If flame roll-out switch is activated do
not attempt to place boiler in operation. Correct
source of blockage and replace flame roll-out
switch.
c. Gas Valve(s) is energized allowing main gas flow
and ignition of Main Burners.
d. After Thermostat is satisfied Gas Valve(s) is de-
energized, extinguishing main flame. Vent
Damper (if used) closes.
2. Safety Shutdown
a. Limit: Automatically interrupts main burner
operation when water temperature exceeds set
point. Maximum allowable temperature is 250°F.
Normal operation resumes when water
d. Thermocouple: senses pilot flame and causes gas
valve to turn off main burner and pilot burner gas
flow should pilot burner flame extinguish.
temperature falls below set point.
ꢀ9
40
b. Blocked Vent Switch. Automatically interrupts
main burner operation when excessive vent
system blockage occurs. Control is a multiple
use device. If blocked vent switch is activated do
not attempt to place boiler in operation. Correct
source of blockage and reset blocked vent
switch.
M. Water Boiler with Intermittent Ignition (EI) and
Intermittent Circulation. See Figure 40.
1. Normal Operation
a. Thermostat calls for heat.
b. Vent Damper (if used) opens as stated in Vent
Damper Sequence of Operation.
c. Flame Roll-out Switch. Automatically interrupts
boiler operation when flames or excessive heat
are present in vestibule. Control is single use
device. If flame roll-out switch is activated do
not attempt to place boiler in operation. Correct
source of blockage and replace flame roll-out
switch.
c. Ignition Module is energized. Pilot Valve opens
and Igniter is energized to ignite Pilot Burner.
d. Sensor proves presence of pilot flame. Main
Valve(s) opens and ignites Main Burners.
e. After Thermostat is satisfied Ignition Module is
de-energized, extinguishing pilot and main
flame. Vent Damper (if used) closes.
d. Igniter/Sensor: senses pilot flame and causes
ignition module to turn off main burner and pilot
burner gas flow should pilot burner flame
2. Safety Shutdown
a. Limit: Automatically interrupts main burner
operation when water temperature exceeds set
point. Maximum allowable temperature is 250°F.
Normal operation resumes when water
extinguish. Five to six minutes after shutdown,
Ignition Module restarts ignition sequence.
For Electronic Ignition Trouble Shooting Guide,
see Page 65. For LED Status Codes, see Tables
8 and 9 on pages 55 and 56.
temperature falls below set point.
41
42
b. Blocked Vent Switch. Automatically interrupts
main burner operation when excessive vent
system blockage occurs. Control is a multiple
use device. If blocked vent switch is activated do
not attempt to place boiler in operation. Correct
source of blockage and reset blocked vent
switch.
N. Water Boiler with Continuous Ignition (Standing Pilot)
and Gravity Circulation. See Figure 41.
1. Normal Operation
a. Thermostat calls for heat. Thermostat Isolation
Relay is energized, closing contacts.
b. Vent Damper (if used) opens as stated in Vent
Damper Sequence of Operation.
c. Flame Roll-out Switch. Automatically interrupts
boiler operation when flames or excessive heat
are present in vestibule. Control is single use
device. If flame roll-out switch is activated do
not attempt to place boiler in operation. Correct
source of blockage and replace flame roll-out
switch.
c. Gas Valve(s) is energized allowing main gas flow
and ignition of Main Burners.
d. After Thermostat is satisfied Gas Valve(s) is de-
energized, extinguishing main flame. Vent
Damper (if used) closes.
2. Safety Shutdown
d. Thermocouple: senses pilot flame and causes gas
valve to turn off main burner and pilot burner gas
flow should pilot burner flame extinguish.
a. Limit: Automatically interrupts main burner
operation when water temperature exceeds set
point. Maximum allowable temperature is 250°F.
Normal operation resumes when water
temperature falls below set point.
4ꢀ
44
b. Blocked Vent Switch. Automatically interrupts
main burner operation when excessive vent
system blockage occurs. Control is a multiple
use device. If blocked vent switch is activated do
not attempt to place boiler in operation. Correct
source of blockage and reset blocked vent
switch.
O. Water Boiler with Intermittent Ignition (EI) and Gravity
Circulation. See Figure 42.
1. Normal Operation
a. Thermostat calls for heat. Thermostat Isolation
Relay is energized, closing contacts.
b. Vent Damper (if used) opens as stated in Vent
Damper Sequence of Operation.
c. Flame Roll-out Switch. Automatically interrupts
boiler operation when flames or excessive heat
are present in vestibule. Control is single use
device. If flame roll-out switch is activated do
not attempt to place boiler in operation. Correct
source of blockage and replace flame roll-out
switch.
c. Ignition Module is energized. Pilot Valve opens
and Igniter is energized to ignite Pilot Burner.
d. Sensor proves presence of pilot flame. Main
Valve(s) opens and ignites Main Burners.
e. After Thermostat is satisfied Ignition Module is
de-energized, extinguishing pilot and main
flame. Vent Damper (if used) closes.
d. Igniter/Sensor: senses pilot flame and causes
ignition module to turn off main burner and pilot
burner gas flow should pilot burner flame
2. Safety Shutdown
extinguish. Five to six minutes after shutdown,
Ignition Module restarts ignition sequence.
a. Limit: Automatically interrupts main burner
operation when water temperature exceeds set
point. Maximum allowable temperature is 250°F.
Normal operation resumes when water
For Electronic Ignition Trouble Shooting Guide,
see Page 65. For LED Status Codes, see Tables
8 and 9 on pages 55 and 56.
temperature falls below set point.
45
46
b. Blocked Vent Switch. Automatically interrupts
main burner operation when excessive vent
system blockage occurs. Control is a multiple
use device. If blocked vent switch is activated do
not attempt to place boiler in operation. Correct
source of blockage and reset blocked vent
switch.
P. Water Boiler with Continuous Ignition (Standing Pilot)
and Tankless Heater. See Figure 43.
1. Normal Operation
a. Thermostat calls for heat or low limit senses
water temperature below set point.
b. Vent Damper (if used) opens as stated in Vent
Damper Sequence of Operation.
c. Flame Roll-out Switch. Automatically interrupts
boiler operation when flames or excessive heat
are present in vestibule. Control is single use
device. If flame roll-out switch is activated do
not attempt to place boiler in operation. Correct
source of blockage and replace flame roll-out
switch.
c. Gas Valve(s) is energized allowing main gas flow
and ignition of Main Burners.
d. After Thermostat or low limit is satisfied Gas
Valve(s) is de-energized, extinguishing main
flame. Vent Damper (if used) closes.
2. Safety Shutdown
d. Thermocouple: senses pilot flame and causes gas
valve to turn off main burner and pilot burner gas
flow should pilot burner flame extinguish.
a. Limit: Automatically interrupts main burner
operation when water temperature exceeds set
point. Maximum allowable temperature is 250°F.
Normal operation resumes when water
temperature falls below set point.
4ꢁ
48
b. Blocked Vent Switch. Automatically interrupts
main burner operation when excessive vent
system blockage occurs. Control is a multiple
use device. If blocked vent switch is activated do
not attempt to place boiler in operation. Correct
source of blockage and reset blocked vent
switch.
Q. Water Boiler with Intermittent Ignition (EI) and
Tankless Heater. See Figure 44.
1. Normal Operation
a. Thermostat calls for heat or low limit senses
water temperature below set point.
b. Vent Damper (if used) opens as stated in Vent
Damper Sequence of Operation.
c. Flame Roll-out Switch. Automatically interrupts
boiler operation when flames or excessive heat
are present in vestibule. Control is single use
device. If flame roll-out switch is activated do
not attempt to place boiler in operation. Correct
source of blockage and replace flame roll-out
switch.
c. Ignition Module is energized. Pilot Valve opens
and Igniter is energized to ignite Pilot Burner.
d. Sensor proves presence of pilot flame. Main
Valve(s) opens and ignites Main Burners.
e. After Thermostat or low limit is satisfied Ignition
Module is de-energized, extinguishing pilot and
main flame. Vent Damper (if used) closes.
d. Igniter/Sensor: senses pilot flame and causes
ignition module to turn off main burner and pilot
burner gas flow should pilot burner flame
2. Safety Shutdown
extinguish. Five to six minutes after shutdown,
Ignition Module restarts ignition sequence.
a. Limit: Automatically interrupts main burner
operation when water temperature exceeds set
point. Maximum allowable temperature is 250°F.
Normal operation resumes when water
For Electronic Ignition Trouble Shooting Guide,
see Page 65. For LED Status Codes, see Tables
8 and 9 on pages 55 and 56.
temperature falls below set point.
49
IX. System Start-up
WARNING
Completely read, understand and follow all
instructions in this manual before attempting
start up.
A. Safe lighting and other performance criteria were met
with the gas manifold and control assembly provided on
boiler when boiler underwent tests specified in
American National Standard for Gas-Fired Low-
Pressure Steam and Hot Water Boilers, ANSI Z21.13.
B. Check Main Burners. Main burners must be in slots in
Figure 46: Gas Valve Pressure Tap,
Honeywell Gas Valves
rear of burner tray and seated on main burner orifices.
C. Fill boiler with water:
1. Steam: fill to normal water line. See Figure 1.
2. Water: fill heating system to approximately 12 PSI.
Vent air from system.
D. Prepare to check operation.
1. Obtain gas heating value (in Btu per cubic foot)
from gas supplier.
2. Adjust limit:
a. Steam: With an L404A1354 - set cut-out
pressure (MAIN scale) on the pressure limit for
(2) PSI and differential pressure (DIFF. scale)
below (2) PSI.
With an L404A1651 or an L404F1367 - set cut-
out pressure (MAIN scale) on the pressure limit
for (1) PSI and differential pressure (DIFF.) for
.5 PSI. These pressures may be varied to suit
individual requirements of the system. See
Figure 18.
Figure 47: Gas Valve Pressure Tap,
Robertshaw Gas Valve
b. Water without tankless heater: set at 200°F.
4. Connect manometer to gas valve pressure tapping
(for IN12 connect to gas valve with pilot control).
See Figure 46 or 47.
c. Water with tankless heater: set limit at 220°F and
operating control to 200°F.
3. Remove front removable panel. See Figure 45.
5. For natural gas fired boiler, temporarily turn off all
other gas-fired appliances.
E. Follow Lighting or Operating Instructions.
1. To place boiler in operation. See Figure 48, 49, 50
or 51. Sequence of Operation is outlined with
wiring diagrams in Section VIII: Electrical.
2. Electronic Ignition Modules with LED indicators.
Table 7 cross-references the ignition module
terminal designations to the ignition terminal
numbers in the wiring ladder diagrams. The yellow
LED indicates the status of the flame, see Table 8.
The green LED indicates the status of the system,
see Table 9. See Figure 52 for LED locations.
Figure 45: Front Door Removal
50
Figure 48: Lighting Instructions, Continuous Ignition System, VR8200 and VR8300 Gas Valves
51
Figure 49: Lighting Instructions, Continuous Ignition System, 7000 ERHC Gas Valve
52
Figure 50: Operating Instruction, Intermittent Ignition System, VR8204 and VR8304
(except IN12) Gas Valves
5ꢀ
Figure 51: Operating Instructions, Intermittent Ignition System (EI), VR8304 (IN12 only) Gas Valves
54
Table ꢁ: Ignition Module Terminal Cross-Reference
Ignition Module
Terminal Designation
Wiring Ladder Diagram
Terminal Number
MV
MV/PV
PV
1
2
3
4
5
6
9
GND
24V (GND)
24V
SPARK
Figure 52: LED Locations
TABLE 8: Yellow LED Flame Codes
Yellow LED
Recommended
Service Action
Indicates
Flash Codea
Heartbeat
Normal Flame Signal
N/A
Weak Flame Signal -
System will operate reliably but flame signal is
less than desired.
Note: This indication may flash temporarily
during or shortly after lightoff on some
applications.
Perform routine
maintenance to
assure optimum
flame signal.
2
Marginal Flame Signal (less than 1.1 µA) -
System may not operate reliably over time.
Service call recommended.
Note: This indication may flash temporarily
during or shortly after lightoff on some
applications.
Check gas supply,
pilot burner, flame
sense wiring,
contamination of
flame rod, burner
ground connection.
1
No Flame or Flame Signal -
below minimum threshold for system operation.
OFF
N/A
aFlash Code Descriptions
- Heartbeat: Constant ½ second bright, ½ second dim cycles.
- The flash code number signifies that the LED flashes X times at 2Hz, remains
off for two seconds, and then repeats sequence.
55
Table 9: Green LED Status Codes
Green LED
Flash Code
Indicates
Next System Action
Recommended Service Action
(X + Y)a
OFF
No “Call for Heat”
N/A
N/A
N/A
None
None
None
Startup - Flame sense
calibration
Flash Fast
Heartbeat
Normal operation
If system fails to light on next trial
for ignition check gas supply, pilot
burner, spark and flame sense wir-
ing, flame rod contamination or out
of position, burner ground connec-
tion.
5 minute Retry Delay-
Pilot flame not detected
during trial for ignition
Initiate new trial for ignition after retry
delay completed.
2
If system fails to light on next trial
for ignition check gas supply, pilot
burner, flame sense wiring, flame
rod contamination, burner ground
connection.
Initiate new trial for ignition. Flash
code will remain through the ignition
trial until flame is proved.
Recycle- Flame failed
during run
3
4
If situation self corrects within 10
Check for pilot flame. Replace gas
valve if pilot flame present. If no
pilot flame, cycle “Call for Heat.” If
error repeats, replace control.
seconds, control returns to normal
sequence. If flame out of sequence re-
mains longer than 10 seconds, control
goes to Flash code 6+4 (see below)
Flame sensed out of
sequence
Check flame sense lead wire for
Control remains in wait mode. When
damage or shorting. Check that
Flame sense leakage to
ground
7
8
the fault corrects, control resumes nor- flame rod is in proper position.
mal operation after a one minute delay. Check flame rod ceramic for cracks,
damage or tracking.
Check transformer and AC line for
Control remains in wait mode. When
proper input voltage to the control.
Low secondary voltage
supply- (below 15.5 Vac)
the fault corrects, control resumes nor-
Check with full system load on the
mal operation after one minute delay.
transformer.
Check gas supply, pilot burner, spark
5 minute Retry Delay-
On every third retry on
same “Call for Heat”
Initiate new trial for ignition after retry
delay completed.
and flame sense wiring, flame rod
contamination or out of position,
burner ground connection.
6 + 2
6 + 3
6 + 4
ON
On every 6th flame
failure during run on the
same “Call for Heat”
Check gas supply, pilot burner, flame
sense wiring, contamination of flame
rod, burner ground connection.
5 minute retry delay, then initiate new
trial for ignition.
Control waits until flame is no longer
sensed and then goes to soft lockout.
Flash code continues. Control auto
Check for pilot flame. Replace gas
valve if pilot flame present. If no
pilot flame, cycle “Call for Heat.” If
Flame sensed out of
sequence- longer than
10 seconds
resets from soft lockout after one hour. error repeats, replace control.
Soft lockout due to error
detected during self
check sequences
Control auto resets from soft lockout
after one hour.
Reset by cycling “Call for Heat.” If
error repeats, replace the control
aFlash Code Descriptions:
-
-
-
Flash Fast: rapid blinking
Heartbeat: Constant ½ second bright, ½ second dim cycles.
A single flash code number signifies that the LED flashes X times at 2Hz, remains off for two seconds, and then
repeats the sequence.
-
X + Y flash codes signify that the LED flashes X times at 2Hz, remains off for two seconds, flashes Y times at 2
Hz, remains off for three seconds, and then repeats the sequence.
56
Figure 56: 40mm Main Burner Flame
Figure 53: Pilot Burner Flame, Honeywell Q350
Figure 57: 1" Main Burner Flame
F. Check pilot burner flame and main burner flames
through observation port.
1. Check pilot flame.
a. Continuous Ignition (Standing Pilot), Models
IN3 through IN7. See Figure 53. Pilot burner
produces a single flame. Flame should be steady,
medium hard blue enveloping 3/8 to ½ inch of
thermocouple.
Figure 54: Pilot Burner Flame, Honeywell Q327
b. Continuous Ignition (Standing Pilot), Models
IN8 through IN12. See Figure 54. Pilot burner
produces three (3) flames. Center flame should
be steady, medium hard blue enveloping 3/8 to ½
inch of thermocouple.
c. Electronic Ignition (EI), Models IN3 through
IN12. See Figure 55. Pilot should be lit only
after completing Step 3. Pilot burner produces
three (3) flames. Center flame should be steady,
medium hard blue enveloping 3/8 to ½ inch of
sensing probe.
CAUTION
Avoid operating this boiler in an environment
where saw dust, loose insulation fibers, dry wall
dust, etc. are present. If boiler is operated under
these conditions, the burner interior and ports
must be cleaned and inspected daily to insure
proper operation.
Figure 55: Pilot Burner Flame, Honeywell Q348
5ꢁ
2. Adjust thermostat to highest setting.
K. Adjust gas input rate to boiler. Natural Gas.
3. Check main burner flames. See Figure 56 or 57.
Flame should have clearly defined inner cones with
no yellow tipping. Orange-yellow streaks caused by
dust should not be confused with true yellow
tipping.
1. Adjust thermostat to highest setting.
2. Check manifold gas pressure. Manifold pressure is
listed on Rating Label.
a. Models IN3-IN12 with Standing Pilot, IN3-IN9
with Hot Surface to Pilot and IN3-IN11 with
Electronic Ignition. Adjust gas valve pressure
regulator as necessary (turn adjustment screw
counterclockwise to decrease manifold pressure,
or clockwise to increase manifold pressure). If
pressure can not be attained, check gas valve
inlet pressure. If less than minimum gas supply
pressure listed on Rating Label, contact gas
supplier for assistance.
4. Adjust thermostat to normal setting.
G. Check thermostat operation. Raise and lower
temperature setting to start and stop boiler operation.
H. Check ignition system shutoff. Gas valve should close
and pilot and main burners extinguish.
1. Continuous Ignition (Standing Pilot): disconnect
thermocouple from gas valve.
b. Model IN12 with Electronic Only.
2. Electronic Ignition (EI): disconnect igniter/sensor
cable from ignition module terminal "9".
i. Turn off gas valve not having pilot control.
ii. On gas valve with pilot control, adjust gas
valve pressure regulator to obtain required
manifold pressure, or if unattainable, highest
pressure without forcing adjustment screw
(turn adjustment screw counterclockwise to
decrease manifold pressure, or clockwise to
increase manifold pressure).
I. Check low water cutoff (steam only).
1. Adjust thermostat to highest setting.
2. With boiler operating, open drain and slowly drain
boiler.
CAUTION
iii. Turn on gas valve not having pilot control.
Adjust gas valve pressure regulator to obtain
required manifold pressure. Manifold
pressure may not change during initial turns
of adjustment screw.
Do not drain below gauge glass.
3. Main burners will extinguish when water level drops
below low water cutoff. Water should still be visible
in gauge glass. Verify limit, thermostat or other
controls have not shut off boiler.
3. Clock gas meter for at least 30 seconds. Use Table
10 to determine gas flow rate in Cubic Feet per
Hour.
4. Adjust thermostat to lowest setting. Refill boiler to
normal water line.
4. Determine Input Rate. Multiply gas flow rate by gas
J. Check Limit.
heating value.
1. Adjust thermostat to highest setting.
5. Compare measured input rate to input rate stated on
Rating Label.
2. Steam: Observe pressure gauge. When pressure is
indicated, adjust limit to setting below observed
pressure. Main burners should extinguish.
a. Boiler must not be overfired. Reduce input rate
by decreasing manifold pressure. Do not reduce
more than 0.3 inch w.c. If boiler is still overfired,
contact your Governale distributor or Regional
Office for replacement Gas Orifice.
WARNING
Failure to properly adjust gas input rate will result
in over firing or under firing of the appliance.
Improper and unsafe boiler operation may result.
b. Increase input rate if less than 98% of Rating
Label input. Increase manifold gas pressure no
more than 0.3 inch w.c. If measured input rate is
still less than 98% of rated input:
3. Water: Observe temperature gauge. When
temperature exceeds limit set point main burners
should extinguish.
i. Remove Main Burners per procedure in
Section X: Service Instructions.
ii. Remove gas orifices. Drill one (1) drill size
4. Adjust limit to setting above observed reading. Main
burners should reignite.
larger (drill size is stamped on orifice).
iii. Reinstall gas orifices and main burners.
5. Adjust thermostat to lowest setting. Adjust limit to
desired setting.
Measure input rate.
6. Recheck Main Burner Flame.
7. Return other gas-fired appliances to previous
conditions of use.
58
1. Oil from new piping connections and sediment in
existing piping must be removed from system to
prevent unsteady water line and carry-over of
entrained water into supply main.
Table 10: Input Rate
Size of Gas Meter Dial
Seconds
for One
Revolution
One-Half
Cu. Ft.
One
Two
Five
a. Fill boiler to normal waterline.
b. Follow Lighting or Operating Instructions to
place boiler in operation. See Figure 48, 49, 50,
or 51.
c. Operate boiler with steam in entire system for
several days to bring system oil and dirt back to
boiler.
Cu. Ft.
Cu. Ft. Cu. Ft.
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
64
66
68
70
72
74
76
78
80
60
56
53
50
47
45
43
41
39
37
36
35
33
32
31
30
29
29
29
28
26
25
24
24
23
22
120
113
106
100
95
90
86
82
78
75
72
69
67
64
62
60
58
56
54
53
51
50
48
47
46
45
240
225
212
200
189
180
172
164
157
150
144
138
133
129
124
120
116
112
109
106
103
100
97
600
563
529
500
474
450
430
410
391
375
360
346
333
321
310
300
290
281
273
265
257
250
243
237
231
225
d. Drain condensate from drain valve in wet return.
Operate boiler until condensate runs clean.
2. Boil-out boiler.
a. Follow instructions TO TURN OFF GAS TO
APPLIANCE. See Figure 48, 49, 50, or 51.
b. Fill boiler to normal waterline.
c. Remove safety valve.
d. Pour recommended boil-out compound into
boiler through safety valve opening.
e. Reinstall safety valve in Tapping "E" with
spindle in vertical position. See Figures 1 and 2.
f. Follow Lighting or Operating Instructions to
place boiler in operation. See Figure 48, 49, 50,
or 51.
Check controls operation per Paragraphs F to J.
Boil water for at least 5 hours.
g. Follow instructions TO TURN OFF GAS TO
APPLIANCE. See Figure 48, 49, 50, or 51.
Drain boiler and system piping.
h. Remove drain valve. Thoroughly wash boiler
water passages with high pressure spray through
drain valve tapping.
i. Reinstall drain valve in Tapping "F". See
Figures 1 and 2.
95
92
90
3. Second Boil-out for Stubborn Cases. If all oil and
grease is not removed a second boilout using surface
blow-off is necessary.
L. Adjust gas input rate to boiler. LP/Propane.
1. Set thermostat to highest setting.
a. Run 1 NPT pipe from Surface Blow-Off Tapping
"L" to open drain. Do not install shut-off valve or
other restriction. See Figure 2.
2. Adjust tank regulator for gas valve inlet pressure of
13.5 inches w.c. or less.
3. Gas valve has step opening regulator which initially
opens to 1.4 or 2.5 inch w.c. and steps to full
b. Fill boiler to top of gauge glass.
c. Remove safety valve.
pressure after approximately 30 seconds. Check
manifold pressure after step has occurred. Adjust gas
valve pressure regulator as necessary for 10.0 inches
w.c. (turn adjustment screw counterclockwise to
decrease manifold pressure, or clockwise to increase
manifold pressure). If 10.0 inches w.c. can not be
attained, check gas valve inlet pressure. If less than
11.0 inches w.c., contact gas supplier for assistance.
d. Pour recommended boil-out compound into
boiler through safety valve opening.
e. Reinstall safety valve in Tapping "E" with
spindle in vertical position. See Figures 1 and 2.
f. Follow Lighting or Operating Instructions to
place boiler in operation. See Figure 48, 49, 50,
or 51. Boil water for approximately 5 hours
without producing steam.
M. Clean Heating System (Steam). A local qualified
water treatment chemical specialist is a suggested
source for recommendations regarding appropriate
chemical compounds and concentrations which are
compatible with local environmental regulations.
g. Open boiler fill shut-off valve to produce steady
trickle of water from surface blow-off pipe.
Continue boil-out for several hours until surface
blow-off water runs clear.
59
h. Follow instructions TO TURN OFF GAS TO
APPLIANCE. See Figure 48, 49, 50, or 51.
Drain boiler and system piping.
or 51. Slowly feed water to boiler. Water will
rise slowly into supply main and back through
return main. Adjust flow to maintain
approximately 180°F water from return main
hose. Continue until water runs clear from hose
for at least 30 minutes.
i. Remove drain valve. Thoroughly wash boiler
water passages with high pressure spray through
drain valve tapping.
j. Turn off water to boiler. Continue to operate until
excess water is removed from boiler and system
(by steaming) and boiler water reaches normal
waterline.
k. Follow instructions TO TURN OFF GAS TO
APPLIANCE. See Figure 48, 49, 50, or 51.
Open all radiator valves. Reinstall all supply
main air valves. Open gate valve in Hartford
Loop.
l. Allow boiler to cool until crown sheet is no
longer too hot to touch. Close drain valves at
boiler and in return main. Fill boiler slowly to
normal waterline.
m. Follow Lighting or Operating Instructions to
place boiler in operation. See Figure 48, 49, 50,
or 51. Allow boiler to steam for 10 minutes.
Drain one quart of water from lower Gauge
Glass fitting.
j. Fill boiler to normal waterline. If water in gauge
glass is not clear, repeat procedure starting at
step b.
k. Remove surface blow-off piping. Install 1 NPT
plug in Tapping "L". See Figure 2.
4. Add Boiler Water Treatment.
a. Remove safety valve.
b. Pour recommended compound into boiler
through safety valve opening.
c. Reinstall safety valve in Tapping "E" with
spindle in vertical position. See Figures 1 and 2.
d. Follow Lighting or Operating Instructions to
place boiler in operation. See Figure 48, 49, 50,
or 51.
e. Boil water or heat water to 180°F.
f. Measure boiler water alkalinity. pH should be
between 7 and 11. Add recommended water
treatment chemicals, if necessary, to bring the pH
within the specified range.
n. Drain second quart sample from lower Gauge
Glass fitting. If sample is not clear, repeat cycle
of draining boiler and return main and refilling
boiler until sample is clear.
5. If unsteady water line, foaming or priming persist:
o. If after normal operation boiler water becomes
dirty from additional system piping sediment
returning to boiler.
a. Follow Lighting or Operating Instructions to
place boiler in operation. See Figure 48, 49, 50,
or 51.
i. Complete steps 5a through 5n.
ii. Complete steps 3a through 3k.
6. Make pH or Alkalinity Test.
b. Install gate valve (shut-off valve) in Hartford
Loop. Install drain valves in return main and at
boiler. See Figure 23.
c. Connect hoses from drain valves to floor drain.
Close gate valve in Hartford Loop. Open drain
valve in return main.
a. After boiler and system have been cleaned and
refilled as previously described, test the pH of
the water in the system. This can easily be done
by drawing a small sample of boiler water and
testing with Hydrion paper which is used in the
same manner as litmus paper, except it gives
specific readings. A color chart on the side of the
small Hydrion dispenser gives the reading in pH.
Hydrion paper is inexpensive and obtainable
from any chemical supply house or through your
local druggist. The pH should be higher than 7
but lower than 11. Add recommended water
treatment chemicals, if necessary, to bring the pH
within the specified range. With this lower level
of protection, care must be exercised to eliminate
all of the free oxygen in the system.
d. Fill boiler to normal water line. Follow Lighting
or Operating Instructions to place boiler in
operation. See Figure 48, 49, 50, or 51.
e. Operate boiler for at least 30 minutes after
condensate begins to run hot. Follow instructions
TO TURN OFF GAS TO APPLIANCE. See
Figure 48, 49, 50, or 51.
f. Close all radiator valves. Remove all supply
main air valves. Plug openings in supply main.
g. Drain approximately 5 gallons of boiler water
into container. Mix in recommended boil-out
compound.
h. Remove safety valve. Pour recommended
compound into boiler through safety valve
opening. Reinstall safety valve in Tapping "E"
with spindle in vertical position. See Figures 1
and 2.
b. Boiler is now ready to be put into service.
N. Clean Heating System (Water). A local qualified
water treatment chemical specialist is a suggested
source for recommendations regarding appropriate
chemical compounds and concentrations which are
compatible with local environmental regulations.
i. Follow Lighting or Operating Instructions to
place boiler in operation. See Figure 48, 49, 50,
60
1. Boiling Out of Boiler and System. Oil and grease
which accumulate in a new hot water boiler can be
washed out in the following manner.
by drawing a small sample of boiler water and
testing with Hydrion paper which is used in the
same manner as litmus paper, except it gives
specific readings. A color chart on the side of the
small Hydrion dispenser gives the reading in pH.
Hydrion paper is inexpensive and obtainable
from any chemical supply house or through your
local druggist. The pH should be higher than 7
but lower than 11. Add recommended water
treatment chemicals, if necessary, to bring the pH
within the specified range. With this lower level
of protection, care must be exercised to eliminate
all of the free oxygen in the system.
a. Remove Safety Relief Valve using extreme care
to avoid damaging it.
b. Partially fill boiler. Pour recommended
compound into boiler through safety relief valve
opening.
c. Replace Safety Relief Valve.
d. Fill entire system with water.
e. Start firing equipment.
f. Circulate the water through the entire system.
g. Vent the system, including the radiation.
b. Boiler is now ready to be put into service.
CONDENSATION — Following a cold start,
condensation (sweating) may occur in a gas fired
boiler to such an extent that it appears that the boiler
is leaking. This condensation can be expected to
stop after the boiler is hot.
h. Allow boiler water to reach operating
temperature, if possible.
i. Continue to Circulate the water for a few hours.
j. Stop the firing equipment.
O. Check Damper Operation - If boiler is equipped with
vent damper, vent damper must be in open position
when boiler main burners are operating. Start boiler,
refer to instructions on damper to determine if damper
is in full open position.
k. Drain the system in a manner and to a location
that hot water can be discharged with safety.
l. Remove plugs from all available returns and
wash the water side of the boiler as thoroughly as
possible, using a high-pressure water stream.
P. Review User's Information Manual and system
m. Refill the system with fresh water.
n. Add recommended boiler water treatment.
2. Make pH or Alkalinity Test.
operation with owner or operator.
Q. Post instructions near boiler for reference by owner
and service personnel. Maintain instructions in legible
condition.
a. After boiler and system have been cleaned and
refilled as previously described, test the pH of
the water in the system. This can easily be done
61
X. Service Instructions
DANGER
This boiler uses flammable gas, high voltage electricity, moving parts, and very hot water under high
pressure. Assure that all gas and electric power supplies are off and that the water temperature is cool
before attempting any disassembly or service.
Assure that all gas valves and electrical disconnect switches are off before attempting any disassembly
or service.
Do not attempt any service work if gas is present in the air in the vicinity of the boiler. Never modify,
remove or tamper with any control device.
WARNING
This boiler must only be serviced and repaired by skilled and experienced service technicians.
If any controls are replaced, they must be replaced with identical models.
Read, understand and follow all the instructions and warnings contained in all the sections of this
manual.
If any electrical wires are disconnected during service, clearly label the wires and assure that the wires
are reconnected properly.
Never jump out or bypass any safety or operating control or component of this boiler.
Read, understand and follow all the instructions and warnings contained in ALL of the component
instruction manuals.
Assure that all safety and operating controls and components are operating properly before placing
the boiler back in service.
A. General. Inspection and service should be conducted
annually, except as noted. Turn off electrical power and
gas supply while conducting service or maintenance.
Follow instructions TO TURN OFF GAS TO
e. Remove light deposits with damp cloth soaked
with vinegar.
f. Remove stubborn deposits using diluted
phosphoric acid (H2PO4) solution, 3 parts water
to 1 part phosphoric acid. Normal operation will
occur with up to 0.2 inch of contamination. If
scale or contamination exceeds 0.2 inches, clean
probe more frequently.
APPLIANCE. See Figures 48, 49, 50 or 51.
B. Maintenance of Low Water Cutoff
1. McDonnell & Miller PS-802 or Hydrolevel
CycleGard CG400 Probe Style Only.
g. Clean Tapping 'K' to remove old pipe dope and
other foreign matter.
a. Drain boiler to point below Tapping 'K'. See
Figure 2.
h. Apply moderate amount of good quality pipe
dope to probe threads, leaving two end threads
bare. Install probe in Tapping 'K'. Mount control
on probe. Attach wire(s) between control and
probe.
b. Disconnect wire(s) connecting control and probe.
c. Remove control from probe.
DANGER
i. Fill boiler to normal waterline. Add water
treatment as needed.
Assure that the boiler is at zero pressure before
removing the LWCO probe. Do not rely on the
pressure gauge to indicate that the boiler is at
zero pressure. Open the safety valve to relieve
all internal pressure prior to proceeding. Safety
valve discharge piping must be piped such that
the potential for burns is eliminated.
2. McDonnell & Miller 67 Float Style Only.
a. Weekly (or more frequently if necessary). Open
blow-off valve to flush sediment chamber.
Follow instructions on Blow-Down Card affixed
to Jacket adjacent to low water cutoff.
b. Annually. Dismantle to extent necessary to
remove obstructions and insure proper function
of working parts.
d. Unscrew probe from Tapping 'K'. Inspect for
scale and sediment buildup.
62
Figure 58: Boiler Flueway Cleaning
i. Inspect connecting lines to boiler for
5. tightness of joints. Remove all accumulations of
soot with wire brush and vacuum
accumulation of mud and scale. Clean as
necessary.
Remove all obstructions. Replace all deteriorated parts
and support properly. Seal all joints.
ii. Examine wiring for brittle or worn
insulation and clean electrical contact.
iii. Inspect solder joints on bellows and float.
Check float for evidence of collapse. Check
mercury bulb (where applicable) for
mercury separation or discoloration. Do not
attempt to repair mechanisms in field.
Complete replacement mechanisms,
including gaskets and instructions, are
available from low water cutoff
E. Clean Boiler Flueways.
1. Shut down gas boiler in accordance with lighting/
operating instructions attached to inside of Front
Removable Door. See Figure 45.
2. Remove Burner Access Panel and Burners. See
Paragraph F. Clean Burners if necessary.
3. Remove Jacket Top Panels.
4. Remove Canopy from top of boiler.
manufacturer.
5. Thoroughly clean the flueways with flue brush. See
c. Five (5) Years or 100,000 switch cycles. Replace
Figure 58.
switch and float mechanisms.
6. Clean boiler heating surface accessible from
combustion chamber with straight handle wire
brush. Reinstall burners and connect gas train. See
Paragraphs F & G.
C. Water Feeder and Additional Low Water Cutoff.
Refer to manufacturer's instructions.
D. Vent System. Check annually for:
7. Place boiler in operation in accordance with
Lighting or Operating instructions. Test gas line for
leaks in accordance with Section VI: Gas Piping,
Paragraph C.
1. obstructions
2. accumulations of soot
3. deterioration of vent pipe or vent accessories due to
condensation or other reasons
4. proper support—no sags, particularly in horizontal
runs
8. Replace Jacket Front Removable Door.
6ꢀ
H. Install Burners by reversing procedures used to
remove burner. Main burners must be in slots in rear of
burner tray and seated on main burner orifices.
Reconnect pilot gas supply, and thermocouple lead
(continuous ignition) or igniter/sensor/ground. See
Table 11 for Pilot Burner location.
CAUTION
When necessary to remove burners, be sure to
reinstall them in the original manner by engaging
the orifice and locating hole in the rear of the
burner tray. Burners must be aligned with the
burner manifold.
Table 11: Pilot Burner Location
F. Remove Burners for cleaning, changing orifice plugs,
Pilot Located Between Burners*
or repairs.
Boiler Size
1. Turn off electric service to boiler.
2. Turn off gas supply to boiler.
3. Remove jacket front panel.
1 inch
1 & 2
40mm
1 & 2
2 & 3
2 & 3
3 & 4
3 & 4
4 & 5
4 & 5
---
IN3
IN4
2 & 3
4. Disconnect pilot tubing at gas valve.
IN5
3 & 4
5. Disconnect thermocouple tubing at gas valve
(Continuous Ignition only). Disconnect igniter/
sensor cable and ground wire at ignition module
Intermittent Ignition (EI) only. Disconnect flame
roll-out switch wires.
IN6
4 & 5
IN7
6 & 7
IN8
7 & 8
6. Remove burner access panel.
IN9
8 & 9
7. Mark location of pilot main burner on manifold.
IN10
IN11
IN12
9 & 10
11 & 12
12 & 13
8. Hold burner on throat. Lift slightly to clear orifice.
Pull burner from combustion chamber. See Figure
10. Pilot main burner can only be removed by lifting
at 45° angle after adjacent burner to right is removed
(1" burners only).
---
---
* Burners numbered left to right as viewed from front of
boiler.
9. Check burners to be sure they do not contain foreign
matter or restrictions. Clean burners with a soft
bristle brush, blow any dirt out with compressed air
or use a vacuum cleaner. See Figure 58.
I. Lubrication. Manufacturers Instruction should be
followed on all parts installed on boiler requiring
lubrication. This includes:
G. Remove Pilot Assembly for Servicing. Remove
machine screw(s) holding pilot burner to pilot bracket,
after first removing burner with pilot assembly as
described in Step F, number 8 above. To adjust or check
spark gap between electrode and hood on Honeywell
Q348 intermittent (EI) pilot, see Figure 59.
1. Type of lubricant to be used.
2. Frequency of lubrication.
3. Points to lubricate.
J. Check operation. Follow Steps B through L and Step
O from Section IX: System Start-up.
l. Use a round wire gauge to check spark gap.
K. Conversion Kits. Follow all instructions provided with
kits. Note that Rating Label provided in kit must be
used. Apply over or beside original Rating Label
allowing the original Serial Number to remain visible.
2. Spark gap should be 0.125" for optimum
performance.
L. Tankless Heater.
1. Flushing of Heater. All water contains some
sediment which settles on inside of coil.
Consequently, heater should be periodically
backwashed. See Figure 28. Allow water at city
pressure to run into hosebib A, through heater, and
out hosebib B until discharge is clear. The tees in
which the hosebibs are located should be the same
size as heater connections to minimize pressure
drop.
2. Adjust and maintain mixing valve (tempering valve)
in accordance with manufacturer's instructions.
Figure 59: Honeywell Q348 Spark Gap
64
A leaky system will increase the volume of make-up
water supplied to the boiler, which can significantly
shorten the life of the boiler. Entrained in make-up
water are dissolved minerals, salts, and oxygen. When
the fresh, cool make-up water is heated in the boiler, the
minerals fall out as sediment, the salts coat the inside of
the boiler, and the oxygen escapes as a gas. The
accumulation of sediment eventually isolates the water
from contacting the cast iron. When this happens the
cast iron in that area gets extremely hot and eventually
cracks. The presence of free oxygen or chloride slats in
the boiler corrodes the cast iron from the inside. More
make-up water and higher concentrations of contami-
nants damage the boiler sooner. Our warranty does
not cover corrosion and sediment-related damage.
Clearly it is in everyone's best interest to prevent this
type of failure. You can do your part by ensuring that
your system is leak-free, keeping leakage to less than 2
percent of the total water volume each month.
M. Excessive Make-Up Water
CAUTION
IF, DURING NORMAL OPERATION, IT IS
NECESSARY TO ADD MORE WATER THAN
INDICATED BELOW, CONSULT A QUALIFIED
SERVICE TECHNICIAN TO CHECK YOUR SYSTEM
FOR LEAKS.
Gallons Per
Gallons Per
Year
Model No.
Month
IN3
IN4
0.1
0.1
0.2
0.2
0.2
0.2
0.3
0.3
0.3
0.4
1
1
2
2
3
3
3
4
4
4
IN5
IN6
IN7
IN8
IN9
IN10
IN11
IN12
65
Honeywell Electronic Ignition Trouble Shooting Guide
66
Honeywell Hot Surface to Pilot Trouble Shooting Guide
6ꢁ
Important Product Safety Information
Refractory Ceramic Fiber Product
Warning:
The Repair Parts list designates parts that contain refractory ceramic fibers
(RCF). RCF has been classified as a possible human carcinogen. When
exposed to temperatures about 1805°F, such as during direct flame contact,
RCF changes into crystalline silica, a known carcinogen. When disturbed as a
result of servicing or repair, these substances become airborne and, if inhaled,
may be hazardous to your health.
AVOID Breathing Fiber Particulates and Dust
Precautionary Measures:
Do not remove or replace RCF parts or attempt any service or repair work
involving RCF without wearing the following protective gear:
1. A National Institute for Occupational Safety and Health (NIOSH)
approved respirator
2. Long sleeved, loose fitting clothing
3. Gloves
4. Eye Protection
• Take steps to assure adequate ventilation.
• Wash all exposed body areas gently with soap and water after contact.
• Wash work clothes separately from other laundry and rinse washing
machine after use to avoid contaminating other clothes.
• Discard used RCF components by sealing in an airtight plastic bag. RCF
and crystalline silica are not classified as hazardous wastes in the United
States and Canada.
First Aid Procedures:
• If contact with eyes: Flush with water for at least 15 minutes. Seek
immediate medical attention if irritation persists.
• If contact with skin: Wash affected area gently with soap and water.
Seek immediate medical attention if irritation persists.
• If breathing difficulty develops: Leave the area and move to a location
with clean fresh air. Seek immediate medical attention if breathing
difficulties persist.
• Ingestion: Do not induce vomiting. Drink plenty of water. Seek
immediate medical attention.
68
XI. Repair Parts
All Independence® Repair Parts may be obtained through your local Burnham Wholesale distributor. Should you require assis-
tance in locating a Burnham Distributor in your area, or have questions regarding the availability of Burnham products or repair
parts, please contact Burnham Customer Service at (717) 481-8400 or Fax (717) 481-8408.
SERVICE RECORD
DATE
SERVICE PERFORMED
69
Quantity
Key
No.
Description
Part No.
IN3 IN4 IN5 IN6 IN7 IN8 IN9 IN10 IN11 IN12
1. Section Assembly
Left End Section (less tankless heater) 717100022
Left End Section (with tankless heater) 717100042
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1A
1B Center Section
1C Right End Section
Tie Rod, 3/8-16 x 10"
Tie Rod, 3/8-16 x 12-1/2"
Tie Rod, 3/8-16 x 17"
Tie Rod, 3/8-16 x 20-3/4"
717100031
717100011
80861071
80861010
80861011
80861012
80861049
80861014
80861034
80861035
80861036
80861020
80860600
80860400
7066003
1
2
3
4
5
6
7
8
9
10
1
1
1
1
1
1
1
1
1
1
2
---
2
---
---
2
---
---
---
2
---
---
---
---
2
---
---
---
---
---
2
---
---
---
---
---
---
2
---
---
---
---
---
---
---
2
---
---
---
---
---
---
---
---
2
---
---
---
---
---
---
---
---
---
2
---
---
---
---
---
---
---
---
---
4
---
---
---
---
---
---
---
---
4
---
---
---
---
---
---
---
4
Tie Rod, 3/8-16 x 23"
1D
---
---
---
---
---
---
4
Tie Rod, 3/8-16 x 27-1/2"
---
---
---
---
---
4
Tie Rod, 3/8-16 x 29"
Tie Rod, 3/8-16 x 32-3/4"
Tie Rod, 3/8-16 x 36-1/2"
Tie Rod, 3/8-16 x 39"
1E Washer, 3/8"
---
---
---
---
4
---
---
---
4
---
---
4
---
4
4
1F Nut, 3/8-16
4
4
4
4
4
4
4
4
4
4
1G Slip Nipple, 5"
1H Slip Nipple, 22B
2
3
4
5
6
7
8
9
10
10
11
11
806600375
2
3
4
5
6
7
8
9
ꢁ0
Quantity
Key
No.
Description
Part No.
IN3 IN4 IN5 IN6 IN7 IN8 IN9 IN10 IN11 IN12
2. Canopy and Draft Hood Canopy/Draft Hood Parts
6111003
6111004
6111005
1
---
1
---
---
1
---
---
---
1
---
---
---
---
1
---
---
---
---
---
1
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
1*
1**
---
---
4
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
1
---
---
---
---
---
---
1
2A Canopy Assembly
6111006
6111007
---
---
---
---
---
---
1
---
---
---
---
---
---
1*
1**
---
---
---
---
---
---
---
---
4
6111008
---
---
---
---
---
---
---
1
6111009
---
---
---
---
---
---
---
1*
1**
---
---
---
---
---
4
61110033
61110043
61110053
61110063
61110064
61110073
61110083
61110084
61110093
61110102
611101021
61110112
61110122
80860115
80860603
80860407
6206001
80860900
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
---
---
---
4
---
---
---
---
---
---
---
---
---
---
---
4
---
---
---
---
---
---
---
---
---
---
4
2B Rear Draft Hood Carton Assembly
---
---
---
---
---
---
---
4
---
---
---
---
4
Canopy/Draft Hood Carton Assembly
(complete)
2C
---
4
2D Carriage Bolt, ¼ -20 x 1"
2E Flat Washer, ¼"
2F Hex Nut, ¼ -20
2G Gasket
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
1
1
1
1
1
1
1
1
1
1
2H Wingnut, ¼ -20
2
2
2
2
2
2
2
---
---
---
All Components for use in both USA or Canada, unless marked with * for USA Only or ** for Canada Only
ꢁ1
Quantity
Key
No.
Description
Part No.
IN3 IN4 IN5 IN6 IN7 IN8 IN9 IN10 IN11 IN12
3. Base Assembly
718600391
1
---
1
---
---
1
---
---
---
1
---
---
---
---
1
---
---
---
---
---
1
---
---
---
---
---
---
1
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
718600491 ---
718600591 ---
718600691 ---
718600791 ---
718600891 ---
718600991 ---
718601091 ---
718601191 ---
718601291 ---
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
3A Base Tray
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
718600311
1
---
---
---
---
---
---
---
---
---
1
718600411 ---
718600511 ---
718600611 ---
718600711 ---
718600811 ---
718600911 ---
718601011 ---
---
---
---
---
---
---
---
---
2
---
---
---
---
---
---
---
2
---
---
---
---
---
---
2
3B Base Wrapper
---
---
---
---
---
2
---
---
---
---
2
---
---
---
2
718601111
718601211 ---
720601
---
---
---
2
---
2
3B1 Base End Insulation
2
2
ꢁ2
Quantity
Key
No.
Description
Part No.
IN3 IN4 IN5 IN6 IN7 IN8 IN9 IN10 IN11 IN12
3. Base Assembly (Continued)
72060035
72060045
72060055
72060065
72060075
72060085
72060095
72060105
72060115
72060126
618600341
1
---
1
---
---
1
---
---
---
1
---
---
---
---
1
---
---
---
---
---
1
---
---
---
---
---
---
1
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
3B2 Base Rear Insulation
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
618600441 ---
618600541 ---
618600641 ---
618600741 ---
618600841 ---
618600941 ---
618601041 ---
618601141 ---
618601241 ---
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
3C Base Front Panel Assembly
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
718600305
1
---
---
---
---
---
---
---
---
---
1
718600405 ---
718600505 ---
718600605 ---
718600705 ---
718600805 ---
718600905 ---
718601005 ---
718601105 ---
718601205 ---
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
Burner Tray (1 Inch Main Burners)
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
3D
---
---
---
---
---
---
---
---
---
4
---
---
---
---
---
---
---
---
6
71806037
71806047
71806057
71806067
71806077
1
---
---
---
---
---
---
---
6
---
---
---
---
---
---
---
---
---
4
Burner Tray (40mm Main Burners)
---
---
---
---
4
---
---
---
4
718600806 ---
718600906 ---
---
---
4
---
4
3E Base Leg Assembly
6186001
71860021
8186006
4
4
4
4
3E1 Base Leg [Included in Key No. 3E]
3E2 Nylon Glide [Included in Key No. 3E]
4
4
4
4
4
4
4
6
6
4
4
4
4
4
4
4
6
6
ꢁꢀ
Quantity
Key
No.
Description
Part No.
IN3 IN4 IN5 IN6 IN7 IN8 IN9 IN10 IN11 IN12
3. Base Assembly (Continued)
718600361
1
---
1
---
---
1
---
---
---
1
---
---
---
---
1
---
---
---
---
---
1
---
---
---
---
---
---
1
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
718600461 ---
718600561 ---
718600661 ---
718600761 ---
718600861 ---
718600961 ---
718601061 ---
718601161 ---
718601261 ---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
1
---
---
---
---
---
---
1
3F Burner Access Panel
---
---
---
---
---
1
---
---
---
---
1
---
---
---
1
---
---
1
---
1
3G Left End Jacket Attachment Bracket
3H Right End Jacket Attachment Bracket
3J Base Sealant
7046011
7046012
6206002
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Screw, Self Tapping, Type F, Phillips
3K
80860700
80860717
16
16
16
16
17
17
17
17
21
21
Pan Head, 1/4 -20 x 1/2", Plated
Screw, Self Tapping, Type F, Hex
3L
4
4
4
4
4
4
4
4
4
4
Head, 5/16 -18 x 1-1/4", Plated
3M Washer, 5/16, USS
80860601
80860464
80860000
4
4
2
4
4
2
4
4
2
4
4
2
4
4
2
4
4
2
4
4
2
4
4
2
4
4
2
4
4
2
3N Hex Lock Nut, 5/16 -18
3P Screw, Sheet Metal, #8 x 1/2"
Manifold and 1" Main Burners
ꢁ4
Quantity
Key
No.
Description
Part No.
IN3 IN4 IN5 IN6 IN7 IN8 IN9 IN10 IN11 IN12
4. Manifold and Main Burners (1 Inch Main Burners Only)
4A
Main Burner
8236099
8236097
2
1
4
6
8
1
11
1
13
---
15
---
17
---
20
---
22
---
Main Burner with Pilot Bracket
(Continuous Ignition) (Q350 Pilot)
1
1
Main Burner with Pilot Bracket
(Continuous Ignition) (Q327 Pilot)
4B
8236098
8236098
---
1
---
1
---
1
---
1
---
1
1
1
1
1
1
1
1
1
1
1
Main Burner with Pilot Bracket
(Intermittent Ignition) (Q348 Pilot)
82260033
82260043
82260053
82260063
82260073
82260083
82260093
82260103
82260113
82260123
822711
1
---
1
---
---
1
---
---
---
1
---
---
---
---
1
---
---
---
---
---
1
---
---
---
---
---
---
1
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
3
---
---
---
---
---
---
---
---
5
---
---
---
---
---
---
---
7
---
---
---
---
---
---
9
4C
Manifold
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
4D
Natural
Gas
Main Burner Orifice, #45 Pink
Main Burner Orifice, #47 White
---
822710
---
---
---
---
12
14
16
18
21
23
Only
Main burner Orifice, #55 Green
Main Burner Orifice, 1.25 mm, Purple
Main Burner Orifice, 3/64", Blue
822708
822705
822704
3
---
5
---
7
---
9
---
---
12
---
---
14
---
---
16
---
---
---
---
---
---
---
---
---
4D
LP Only
---
---
---
---
---
Screw, Machine, Slotted Round Head,
10-32 x 3/16"
4E
4F
80860800
80860700
2
2
2
2
2
2
2
2
2
2
Screw, Self Tapping, Phillips Pan
Head, 1/4 -20 x 1/2"
4
4
4
4
4
4
4
4
4
4
Note: Orifice Sizes shown for normal altitude (0-2000 feet). For High Altitude consult factory.
ꢁ5
Manifold and 40mm Main Burners
Quantity
IN3 IN4 IN5 IN6 IN7 IN8 IN9
Key
No.
Description
Part No.
4. Manifold and Main Burners (40MM MAIN BURNERS ONLY)
4A
Main Burner
8236135
1
1
2
1
3
4
5
6
7
1
Intermittent Ignition Only
4B
Main Burner with 41° Pilot Bracket
8236136
1
1
1
1
24-Volt Continuous Ignition (Standing Pilot) Natural Gas
Main Burner with 48° Pilot Bracket
Main Burner with 41° Pilot Bracket
8236143
8236136
1
1
1
1
---
1
---
1
---
1
4B
---
---
---
---
24-Volt Continuous Ignition (Standing Pilot) LP Gas
4B
Main Burner with 41° Pilot Bracket
823136
1
1
1
1
1
1
1
82260038
82260048
82260058
82260068
82260078
82260088
82260098
1
---
1
---
---
1
---
---
---
1
---
---
---
---
1
---
---
---
---
---
1
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
---
---
4C
Manifold
---
---
---
---
---
---
---
---
---
---
ꢁ6
Quantity
IN6
Key
No.
Description
Part No.
IN3
IN4
IN5
IN7
IN8
IN9
4. Manifold and Main Burners (40MM MAIN BURNERS ONLY) Continued
Natural Gas, High Altitude (2000-5000 Ft.) USA Only
Main Burner Orifice #39
Main Burner Orifice #38
822727
822720
2
3
---
---
---
---
7
---
8
4D
---
---
4
5
6
LP Gas, High Altitude (2000-5000 Ft.) USA Only
4D
Main Burner Orifice #53
822722
2
3
4
5
6
7
8
Natural Gas, High Altitude (5000-9000 Ft.) USA Only
Main Burner Orifice #41
Main Burner Orifice #42
822729
2
3
---
---
---
---
7
---
8
4D
822728
---
---
4
5
6
LP Gas, High Altitude (5000-9000 Ft.) USA Only
Main Burner Orifice #54
4D
822734
822722
2
---
---
---
---
---
7
---
8
Main Burner Orifice #53
---
3
4
5
6
Natural Gas, High Altitude (2000-4500 Ft.) Canada Only
Main Burner Orifice #37
Main Burner Orifice #36
822719
822771
2
---
---
---
---
---
7
---
8
4D
---
3
4
5
6
LP Gas, High Altitude (2000-4500 Ft.) Canada Only
4D
4E
Main Burner Orifice #52
822721
2
2
3
4
5
6
7
2
8
2
Screw, Machine, Slotted Round Head,
#10-32 x 3/16"
80860800
2
2
2
2
Screw, Self Tapping, Phillips Pan Head,
1/4 - 20 x 1/2"
4F
80860700
4
4
4
4
4
4
4
718600362
718600462
718600562
718600662
718600762
718600862
718600962
1
---
1
---
---
1
---
---
---
1
---
---
---
---
1
---
---
---
---
---
1
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
---
---
4G
---
---
---
---
Injection Shield Assembly
---
---
---
---
---
---
ꢁꢁ
Quantity
Key
No.
Description
Part No.
IN3 IN4 IN5 IN6 IN7 IN8 IN9 IN10 IN11 IN12
5. Pilot Burner and Gas Valve, Continuous Ignition (Standing Pilot), Natural Gas
Pilot Burner, Honeywell Q350A1321
Pilot Burner, Honeywell Q327A1006
Pilot Orifice, Honeywell 390686-22
Pilot Orifice, Honeywell 388146AG
8236065
8236022
1
---
1
1
---
1
1
---
1
1
---
1
1
1**
1
---
1
---
1
---
1
---
1
---
1
5A
---
1
---
1
---
1
---
1
---
1
Included
with 5A
5B
5C
5D
---
---
---
---
---
Compression Nut/Fitting, 1/4" OD x 1/4
C.C. (Included with 5A)
8236109
2
2
2
2
2
2
2
2
2
2
Pilot Tubing, 1/4" OD x 30"
8236122
8236123
81660143
1
---
1
1
---
1
1
---
1
1
---
1
1
---
---
---
1
---
1
---
1
---
1
---
1
---
1
Pilot Tubing, 1/4" OD x 40"
Gas Valve, Honeywell VR8200C3005
Gas Valve, Honeywell VR8200C6065
Gas Valve, Honeywell VR8300C4027
Gas Valve, Honeywell VR8300C4266
---
---
1
---
---
1
---
---
---
---
---
---
---
---
---
---
---
---
100333-01 1**
1**
---
---
1**
---
---
1**
---
---
81660154
100334-01
---
---
5E
1**
1**
1**
Gas Valve, Robertshaw
7000ERHC-S7C
81660156
---
---
---
---
---
---
---
1
1
1
Gas Valve, ITT K3A451
81660080
8236024
---
1
---
1
---
1
---
1
---
1
---
1
---
1
1
1
1
1
1
1
5F Thermocouple, Honeywell Q309A
5. Pilot Burner and Gas Valve, Continuous Ignition (Standing Pilot), LP/Propane
Pilot Burner, Honeywell Q350A1339
Pilot Burner, Honeywell Q327A1147
Pilot Orifice, Honeywell 390686-23
Pilot Orifice, Honeywell 388146KR
8236066
8236023
1
1**
1
1
1**
1
1
1**
1
1
1**
1
1
1**
1
---
1
---
1
---
---
---
---
---
---
---
---
---
---
---
---
5A
---
1
---
1
Included
with 5A
5B
5C
5D
---
---
---
---
---
Compression Nut/Fitting, 1/4" OD x 1/4
C.C. (Included with 5A and 5E)
8236109
2
2
2
2
2
2
2
---
---
---
Pilot Tubing, 1/4" OD x 30"
8236122
8236123
81660144
81660163
8236024
1
---
1
1
---
1
1
---
1
1
---
1
1
---
---
1
---
1
---
1
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
Pilot Tubing, 1/4" OD x 40"
Gas Valve, Honeywell VR8200C3013
Gas Valve, Honeywell VR8300C4035
---
1
---
1
5E
---
1
---
1
---
1
---
1
5F Thermocouple, Honeywell Q309A
1
1
1
Note: Gas Valve specifications shown for normal altitude (0-2000 feet). For High Altitude consult factory.
** 40mm Burners Only
ꢁ8
Quantity
Key
No.
Description
Part No.
IN3 IN4 IN5 IN6 IN7 IN8 IN9 IN10 IN11 IN12
5. Pilot Burner and Gas Valve, Intermittent Ignition (EI), Natural Gas
5A Pilot Burner, Honeywell Q348A1002
8236072
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Included
with 5A
5B Pilot Orifice, Honeywell 388146NE
Compression Nut/Fitting, 1/4" OD x 1/4
C.C. (Included with 5A and 5E)
5C
8236109
2
2
2
2
2
2
2
2
2
2
Pilot Tubing, 1/4" OD x 30"
5D
8236122
8236123
81660145
81660161
1
---
1
1
---
1
1
---
1
1
---
1
1
---
---
1
---
1
---
1
---
1
---
1
---
1
Pilot Tubing, 1/4" OD x 40"
Gas Valve, Honeywell VR8204C3007
5E
---
1
---
1
---
1
---
1
---
2
Gas Valve, Honeywell VR8304P4306
---
---
---
---
Igniter/Sensor Cable, 36", Honeywell
394800-36
5F
8236084
6136054
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
5G Ground Wire Assembly
5. Pilot Burner and Gas Valve, Intermittent Ignition (EI), LP/Propane
5A Pilot Burner, Honeywell Q348A1010
8236081
1
1
1
1
1
1
1
1
1
1
1
1
1
1
---
---
---
---
---
---
Included
with 5A
5B Pilot Orifice, Honeywell 388146KP
Compression Nut/Fitting, 1/4" OD x 1/4
C.C. (Included with 5A and 5E)
5C
8236109
2
2
2
2
2
2
2
---
---
---
Pilot Tubing, 1/4" OD x 30"
5D
8236122
8236123
81660146
81660160
1
---
1
1
---
1
1
---
1
1
---
1
1
---
---
1
---
1
---
1
---
---
---
---
---
---
---
---
---
---
---
---
Pilot Tubing, 1/4" OD x 40"
Gas Valve, Honeywell VR8204C3015
5E
---
1
---
1
Gas Valve, Honeywell VR8304P4314
---
---
---
---
Igniter/Sensor Cable, 36" Honeywell
394800-36
5F
8236084
6136054
1
1
1
1
1
1
1
1
1
1
1
1
1
1
---
---
---
---
---
---
5G Ground Wire Assembly
Note: Gas Valve specifications shown for normal altitude (0-2000 feet). For High Altitude consult factory.
ꢁ9
80
Quantity
Key
No.
Description
Part No.
IN3 IN4 IN5 IN6 IN7 IN8 IN9 IN10 IN11 IN12
Jacket Assembly
60410013
60410023
60410012
60410022
60410033
60410043
60410053
60410063
60410073
60410083
60410093
60410103
60410113
60410123
60410034
60410044
60410054
60410064
60410074
60410084
60410094
60410104
60410114
60410124
60410035
60410045
60410055
60410065
60410075
60410085
60410095
60410105
60410115
60410125
1
1
1
1
1
1
1
---
1
---
1
---
1
1
2
Left Side Panel
---
1
---
1
---
1
---
1
---
1
---
1
---
1
---
1
---
1
---
1
Right Side Panel
---
1
---
---
1
---
---
---
1
---
---
---
---
1
---
---
---
---
---
1
---
---
---
---
---
---
1
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
3
Front Removable Panel
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
4
Vestibule Panel
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
5
Rear Panel
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
81
Quantity
Key
No.
Description
Part No.
IN3 IN4 IN5 IN6 IN7 IN8 IN9 IN10 IN11 IN12
Jacket Assembly (Continued) - Refer to Figure on Page 80
5A Upper Left Rear Panel (not shown)
604101051 ---
604101052 ---
---
---
---
1
---
---
---
---
1
---
---
---
---
---
1
---
---
---
---
---
---
1
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
1
1
1
1
5B Upper Right Rear Panel (not shown)
1
1
1
60410036
60410046
60410056
60410066
60410076
60410086
60410096
60410106
60410116
60410126
604100361
1
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
6A Front Top Panel
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
604100461 ---
604100561 ---
604100661 ---
604100761 ---
604100861 ---
604100961 ---
604101061 ---
604101161 ---
604101261 ---
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
6B Rear Top Panel
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
1
70410034
70410044
70410054
70410064
70410074
70410084
70410094
70410104
70410114
70410124
1
---
---
---
---
---
---
---
---
---
1
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
7
Lower Front Tie Bar
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
82
Key
No.
Description
Part No.
Quantity
Steam Trim
7A Safety Valve, 3/4 NPT, 15 psi, Conbraco 13-511-08
7B Elbow, 3/4 NPT
81660530
806601502
806600002
80160720
80160725
80160517
80160629
8056128
1
2
2
7C Nipple, 3/4 NPT x 3"
Low Water Cutoff, McDonnell & Miller PS-802-24 (Probe Included)
8A Low Water Cutoff, Hydrolevel CG400-2090 (Less Probe - See Key No. 8B)
Low Water Cutoff, McDonnell & Miller 67-BC-1 (Float Type)
8B Probe for CG400
1
1
1
Gauge Glass, Extended Shank (with Probe LWCO Only)
9
Gauge Glass, Standard Shank (with Float LWCO Only)
8056020
10A Limit, Honeywell L404F1367
10B Syphon, 1/4 NPT x 90°
10C Bushing, 3/4 NPT x 1/4 NPT
10D Syphon, 1/4 NPT x 180°
11A Pressure Gauge
80160369
806603010
806600508
806603030
8056010
1
1
1
1
1
1
1
11B Drain Valve, Conbraco 31-612-02
11C Bushing, 2 NPT x 3/4 NPT
806603012
806600515
8ꢀ
84
Key
No.
Description
Part No. IN3 IN4 IN5 IN6 IN7 IN8 IN9 IN10 IN11 IN12
Water Trim
Safety Relief Valve, 3/4 NPT, 30 psi,
Conbraco 10-407-05
7A
81660363
1
1
1
1
1
1
1
1
1
1
7B Elbow, 3/4 NPT
806601520
806600002
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
7C Nipple, 3/4 NPT x 3"
Circulator, Bell & Gossett NRF-22 with
Gaskets
8056174
8A
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
Circulator, Grundfos UP 15-42F
8056044
8056007
Circulator, Taco 007
Gasket, Bell & Gossett NRF-22
8B Gasket, Grundfos 510179
Gasket, Taco '00' Series
806602029
806602016
806602006
806602014
80861301
80860406
6031201
8C Flange, 1-1/2 NPT
2
4
2
4
2
4
2
4
2
4
4
1
1
1
1
1
1
6
6
2
4
4
1
1
1
1
1
1
6
6
2
4
4
1
1
1
1
1
1
6
6
2
4
4
1
1
1
1
1
1
6
6
2
4
4
1
1
1
1
1
1
6
6
2
4
4
1
1
1
1
1
1
6
6
8D Screw, Cap Hex Head, 7/16 -14 x 1-1/2"
8E Nut, Hex, 7/16 -14
4
4
4
4
Tankless Heater, A-62
---
---
---
---
1
1
1
1
Tankless Heater, #222
6036007
---
---
---
1
1
1
9A
Tankless Heater, A-51
6031202
---
---
1
1
Tankless Heater, A-53
Heater Cover Plate
6031203
---
1
7036001
9B Gasket
8036020
1
1
1
1
9C Washer, 3/8"
80860600
80861337
6
6
6
6
9D Screw, Cap Hex Head, 3/8 -16 x 7/8"
6
6
6
6
Limit, Honeywell L8148E1299
(Intermittent Circulation Only)
80160607
80160469
80160400U
80160452
80160426
8056169U
Limit, Honeywell L6081A1010
10A
1
1
1
1
1
1
1
1
1
1
(Tankless Heater Only)
Limit, Honeywell L4006A2015
(Gravity Circulation Only)
Well, Honeywell 123871A
(Tankless Heater Only)
10B
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Well, Honeywell 123870A (Intermittent or
Gravity Circulation Only)
Temperature/Pressure Gauge,
ENFM 41042.5210
11A
11B Drain Valve, Conbraco 31-612-02
11C Bushing, 2 NPT x 3/4 NPT
806603012
806600515
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Transformer, 50VA, Honeywell AT150D1019
(Tankless Heater or Gravity Circulation Only)
12
80160186
80160265
80160127
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Relay, DPST, Honeywell R8225D1029
(Tankless Heater Only)
13
Relay, SPST, Honeywell R8222K1000
(Gravity Circulation Only)
14
85
Key
No.
Quantity
Description
Part No.
IN3 IN4 IN5 IN6 IN7 IN8 IN9 IN10 IN11 IN12
Transformer/J-Box Adapter Plate
1
2
3
Junction Box, 4-11/16" x 4-11/16" x 2-1/8" 81361761
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Transformer/J-Box Adapter Plate
7011001
Sheet Metal Screw, #8 x 1/2, Type B,
Phillips Head, Blunt
80860019
2
2
2
2
2
2
2
2
2
2
4
5
O/CL Bushing, Heyco OCB-875
J-Box Attachment Bracket
8136066
7131001
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
86
THIS PAGE LEFT BLANK INTENTIONALLY
8ꢁ
88
Quantity
Key
No.
Description
Part No.
IN3 IN4 IN5 IN6 IN7 IN8 IN9 IN10 IN11 IN12
12. Transformer (Steam and Gravity Water Only)
12A Junction Box, 4-11/16" x 4-11/16" x 2-1/8"
Refer to Table on Page 86
12B Transformer, 50 VA, Honeywell AT150D1019 80160186
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
12C Relay, SPST, Honeywell R8222K1000
80160127
1ꢀ. Flame Rollout Switch
13A Flame Rollout Switch
80160044
7186018
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
13B Flame Rollout Switch Bracket
14. Blocked Vent Switch
6016067
6111001
1
1
1
1
1
1
1
---
1
---
1
---
1
14 Blocked Vent Switch
---
---
---
---
---
---
---
15. Ignition Module (Intermittent Ignition Only)
15 Ignition Module, Honeywell S8610M3009
100958-01
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
--- Ignition Module Support Bracket
7016001
16. Vent Damper
4"
5"
8116321
8116322
8116323
8116324
8116325
8116326
1
---
1
---
---
1
---
---
1*
---
---
---
1
---
---
---
1*
---
---
---
---
1
---
---
---
---
1*
---
---
---
---
---
1
---
---
---
---
---
1
---
---
---
---
---
6"
---
---
---
---
16
7"
--- 1**
8"
---
---
---
---
--- 1**
--- ---
9"
---
1**
All components for use in both USA and Canada, unless marked with * for USA Only or ** for Canada Only.
89
XII. Low Water Cut Off (LWCO)
WARNING
DO NOT ATTEMPT to cut factory wires to install an aftermarket Low Water Cut Off (LWCO). Only use
connections specifically identified for Low Water Cut Off.
In all cases, follow the Low Water Cut Off (LWCO) manufacturer's instructions.
When
manufacturers recommend an annual inspection of the
probe.
A low water cutoff is required to protect a hot water
boiler when any connected heat distributor (radiation) is
installed below the top of the hot water boiler (i.e.
baseboard on the same floor level as the boiler). In
addition, some jurisdictions require the use of a LWCO
with a hot water boiler.
How to Wire
LWCO’s are available in either 120 VAC or 24 VAC
configurations. The 120 VAC configuration can be
universally applied to both gas and oil boilers by wiring
it in the line voltage service to the boiler (after the
service switch, if so equipped).
Where
The presence of water in a properly installed LWCO
will cause the normally open contact of the LWCO to
close, thus providing continuity of the 120 VAC service
to the boiler.
It is recommended to supply power to the probe LWCO
with the same line voltage boiler service as shown
below.
The universal location for a LWCO on both gas and oil
hot water boilers is above the boiler, in either the supply
or return piping. The minimum safe water level of a
water boiler is at the uppermost top of the boiler; that is,
it must be full of water to operate safely.
What Kind
Typically, in residential applications, a probe type
LWCO is used instead of a float type, due to their
relative costs and the simplicity of piping for a probe
LWCO.
How to Pipe
A “tee” is commonly used to connect the probe LWCO
to the supply or return piping, as shown below.
Wiring of Typical LWCO
A 24 VAC LWCO is used primarily for gas fired boilers
where a 24 volt control circuit exists within the boiler.
However, a 24 VAC LWCO can only be used if the
boiler manufacturer has provided piping and wiring
connections and instructions to allow for this
application.
LWCO Location
Select the appropriate size tee using the LWCO
manufacturer’s instructions. Often, the branch
connection must have a minimum diameter to
prevent bridging between the probe and the tee. Also,
the run of the tee must have a minimum diameter to
prevent the end of the probe from touching or being
located too close to the inside wall of the run of the tee.
How to Test
Shut off fuel supply. Lower water level until water
level is BELOW the LWCO. Generate a boiler demand
by turning up thermostat. Boiler should not attempt to
operate. Increase the water level by filling the system.
The boiler should attempt to operate once the water
level is above the LWCO.
Ideally, manual shutoff valves should be located above
the LWCO and the boiler to allow for servicing. This
will allow probe removal for inspection without
draining the heating system. Many probe LWCO
90
Limited Warranty
FOR RESIDENTIAL GRADE WATER BOILERS
Subject to the terms and conditions set forth below, U.S. Boiler™
if the residential grade water boiler is used or operated over its rated
capacity, is subjected to unauthorized modification, or is damaged
as a result of being otherwise improperly operated or serviced
including, but not limited to, damage from any of the following:
operation with insufficient water, allowing the boiler to freeze,
subjecting the boiler to flood conditions, and operation with
unapproved water or fuel additives which cause deposits or
corrosion.
Co., Inc. Lancaster, Pennsylvania hereby extends the following limited
warranties to the original owner of a residential grade water boiler
manufactured and shipped on or after July 1,1991:
ONE YEAR LIMITED WARRANTY
ON RESIDENTIAL GRADE WATER BOILERS
U.S. Boiler Co., Inc. warrants to the original owner that its residential
grade water boilers comply at the time of manufacture with recognized
hydronic industry standards and requirements then in effect and will be
free of defects in material and workmanship under normal usage for a
period of one year from the date of original installation. If any part of
a water boiler is found to be defective in material or workmanship during
this one year period, U.S. Boiler Co., Inc. will, at its option, repair or
replace the defective part.
5.Removal and Installation: These warranties do not cover
expenses of removal or reinstallation. The owner is responsible for
the cost of removing and reinstalling any defective part and its
replacements and all labor and material connected therewith.
6.Exclusive Remedy: U.S. Boiler Co., Inc. obligation for any breach
of these warranties is limited to the repair or replacement of its
parts in accordance with the terms and conditions of these
warranties.
LIFETIME LIMITED WARRANTY
ON HEAT EXCHANGER
7.Limitation of Damages: Under no circumstances shall U.S. Boiler
Co., Inc. be liable for incidental, indirect, special or consequential
damages of any kind whatsoever under these warranties, including,
but not limited to, injury or damage to persons or property and
damages for loss of use, inconvenience or loss of time. U.S. Boiler
Co., Inc. liability under these warranties shall under no circum-
stances exceed the purchase price paid by the owner for the
residential grade water boiler involved. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so
the above limitation or exclusion may not apply to you.
U.S. Boiler Co., Inc. warrants to the original owner that the heat
exchanger of its residential grade water boilers will remain free from
defects in material and workmanship under normal usage for the
lifetime of the original owner at the original place of installation. If a
claim is made under this warranty during the first ten years from the
date of original installation, U.S. Boiler Co., Inc. will, at its option, repair
or replace the heat exchanger. If a claim is made under this warranty
after the expiration of ten years from the date of original installation,
U.S. Boiler Co., Inc. will, at its option and upon payment of the pro-rated
service charge set forth below, repair or replace the heat exchanger.
The service charge applicable to a heat exchanger warranty claim is
based upon the number of years the heat exchanger has been in
service and will be determined as a percentage of the retail price of the
heat exchanger model involved at the time the warranty claim is made
as follows:
8.Limitation of Warranties: These warranties set forth the entire
obligation of U.S. Boiler Co., Inc. with respect to any defect in a
residential grade water boiler and U.S. Boiler Co., Inc. shall have no
express obligations, responsibilities or liabilities of any kind whatso-
ever other than those set forth herein. These warranties are given in
lieu of all other express warranties.
Years
In Service
1-10
11
12
13
15
14
20
15
25
16
17
ALL APPLICABLE IMPLIED WARRANTIES, IF ANY, INCLUDING
ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE ARE EXPRESSLY LIMITED IN
DURATION TO A PERIOD OF ONE YEAR EXCEPT THAT
IMPLIED WARRANTIES, IF ANY, APPLICABLE TO THE HEAT
EXCHANGER IN A RESIDENTIAL GRADE WATER BOILER SHALL
EXTEND TO THE ORIGINAL OWNER FOR THE LIFETIME OF
THE ORIGINAL OWNER AT THE ORIGINAL PLACE OF
INSTALLATION. SOME STATES DO NO ALLOW LIMITATION ON
HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE
LIMITATION MAY NOT APPLY TO YOU.
Service Charge
as % of
Retail Price
No
Charge
5
10
30
35
Years
In Service
25 and
above
18
19
20
21
22
23
24
Service Charge
as % of
40
45
50
55
60
65
70
75
Retail Price
NOTE: If the heat exchanger model involved is no longer available
due to product obsolescence or redesign, the value used to
establish the retail price will be the published price as shown in the
Burnham Hydronics Repair Parts Price Sheet where the heat
exchanger last appeared or the current retail price of the then
nearest equivalent heat exchanger.
PROCEDURE FOR OBTAINING WARRANTY SERVICE
In order to assure prompt warranty service, the owner is
requested to complete and mail the attached Warranty Card within
ten days after the installation of the boiler, although failure to comply
with this request will not void the owner’s rights under these
warranties.
ADDITIONAL TERMS AND CONDITIONS
Upon discovery of a condition believed to be related to a defect in
material or workmanship covered by these warranties, the owner
should notify the installer, who will in turn notify the distributor. If
this action is not possible or does not produce a prompt response,
the owner should write to U.S. Boiler Co., Inc., Burnham Hydronics,
at P.O. Box 3079, Lancaster, PA 17604, giving full particulars in
support of the claim.
1.Applicability: The limited warranties set forth above are extended
only to the original owner at the original place of installation within
the United States and Canada. These warranties are applicable
only to water boilers designated as residential grade by U.S. Boiler
Co., Inc. and installed in a single or two-family residence and do not
apply to steam boilers of any kind or to commercial grade boilers.
2. Components Manufactured by Others: Upon expiration of the one
year limited warranty on residential grade water boilers, all boiler
components manufactured by others but furnished by U.S. Boiler
Co., Inc. (such as oil burner, circulator and controls) will be subject
only to the manufacturer’s warranty, if any.
The owner is required to make available for inspection by U.S.
Boiler Co., Inc. or its representative the parts claimed to be
defective and, if requested by U.S. Boiler Co., Inc. to ship these
parts prepaid to U.S. Boiler Co., Inc. at the above address for
inspection or repair. In addition, the owner agrees to make all
reasonable efforts to settle any disagreement arising in connection
with a claim before resorting to legal remedies in the courts.
3. Proper Installation: The warranties extended by U.S. Boiler Co.,
Inc. are conditioned upon the installation of the residential grade
water boiler in strict compliance with U.S. Boiler Co., Inc. installation
instructions. U.S. Boiler Co., Inc. specifically disclaims liability of
any kind caused by or relating to improper installation.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND
YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
4. Proper Use and Maintenance: The warranties extended by U.S.
Boiler Co., Inc. conditioned upon the use of the residential grade
water boiler for its intended purposes and its maintenance
accordance with U. S. Boiler Co., Inc. recommendations and
hydronics industry standards. These warranties will be inapplicable
03/03
Limited Warranty
FOR RESIDENTIAL CAST IRON STEAM BOILERS
By this Warranty Statement the U.S. Boiler™ Company, Inc. of Lancaster,
5. This warranty applies only to boilers installed within the United States, and
Canada.
Pennsylvania issues limited warranties subject to the terms and conditions
stated below. These limited warranties apply to residential cast iron boilers
labeled Independence®, Independence® PV, V8H™ and MegaSteam™ Series,
these warranties are issued only to the original homeowner at the original
place of installation.
6. In order for this warranty to be effective:
a.) The boiler must have been properly installed in a single or two-family
residential dwelling. This warranty does not apply to boilers installed in
apartments or to commercial or industrial installation.
FIRSTYEAR - LIMITED WARRANTY FOR
RESIDENTIAL CAST IRON STEAM BOILERS
b.) The boiler must have been assembled in strict compliance with
installation instructions furnished with the boiler by U.S. Boiler Company, Inc.
c.) Boiler components must not have been damaged in handling during
shipment or installation.
U.S. Boiler Company, Inc. warrants its residential cast iron steam boilers
labeled Independence, Independence PV, V8H and MegaSteam Series to be
free of defects in material and workmanship when shipped and to remain free
of such defects under normal usage for a period of one year from the date of
original installation. In the event that any part of such a steam boiler is found
to be defective in material or workmanship during the one-year period, then
U.S. Boiler Company, Inc. will repair or replace, at its option, the defective
part.
7. The foregoing provisions of this warranty shall be effective to the maximum
extent permitted by applicable law, and, to the extent that any such
provision would otherwise be inconsistent with applicable law, such
provision shall be limited in effect to the minimum extent necessary to avoid
such unconscionable result or inconsistency with applicable law.
8. The remedy for breach of this warranty is expressly limited to the repair or
replacement of any part found to be defective under conditions of normal
use; and the remedy for breach of this warranty or for negligence does not
extend to liability for incidental, special or consequential damages or losses
such as loss of the use of the materials, inconvenience or loss of
time. Some states do not allow the exclusion or limitation of incidental or
consequential damages so the above limitation or exclusion may not apply
to you.
SECOND THROUGH 10YEAR - LIMITED
WARRANTY FOR THE CAST IRON SECTION
ASSEMBLY OF RESIDENTIAL CAST IRON STEAM BOILERS
U.S. Boiler Company, Inc. warrants the cast iron section assembly of its
residential cast iron steam boilers labeled Independence, Independence PV,
V8H and MegaSteam Series, to be free of defects in material and
workmanship when shipped and to remain free of such defects under normal
usage for a period of 10 years from the date of original boiler installation.
In the event that such cast iron section assembly is found to be defective in
material or workmanship during this period, U.S. Boiler Company, Inc. will
repair or replace, at its option, the defective cast iron section assembly.
9. This warranty is in lieu of all others, and any and all express or implied
warranties (including, without limitation, any implied warranties of
merchantability or tness for a particular purpose) are expressly limited in
duration to the period of the warranty as previously stated herein. Some
states do not allow limitation on how long an implied warranty lasts, so
the above limitation may not apply to you.
FIRST THROUGH 5YEAR - LIMITED WARRANTY AGAINST
WATERSIDE CORROSION IN THE MEGASTEAM SERIES
10.Not withstanding any of the above provisions, U.S. Boiler Company, Inc.
liability under this warranty shall not exceed the selling price of the
product found to be defective.
U.S. Boiler Company, Inc. warrants the cast iron sections of the MegaSteam
boiler to resist TEMPERATURE INDUCED CHLORIDE ACTIVATED
GRAPHITIC CORROSION for a period of ve years from the date of original
installation. In the event that any cast iron section of a MegaSteam boiler fails
due to this corrosion mechanism during this period, U.S. Boiler Company, Inc.
will repair or replace, at its option, the failed cast iron section assembly.
PROCEDURE FOR OBTAINING WARRANTY SERVICE
In order to assure prompt warranty service the homeowner is requested
to complete and mail the attached Warranty Card within ten days after the
installation of the boiler, although failure to comply with this request will not
void the homeowner’s rights under this warranty.
LIFETIME NIPPLE LEAKAGE WARRANTY
U.S. Boiler Company, Inc. warrants the cast iron and steel nipples that join the
sections to be free from defects in material and workmanship for the lifetime
of the original owner at the time of installation. In the event that such nipples
are found to be defective in material or workmanship during this period, U.S.
Boiler Company, Inc. will repair or replace at its option, the cast iron section
assembly.
Upon discovery of a condition believed to be related to a defect in material
or workmanship covered by this warranty statement, the homeowner should
notify the installer who will in turn notify the distributor. If this action is not
possible or does not produce a prompt response, the homeowner should write
to U.S. Boiler Company, Inc., at P.O. Box 3079, Lancaster, PA 17604 giving full
particulars in support of the claim.
ADDITIONAL TERMS AND CONDITIONS
The homeowner is required to make available for inspection by U.S. Boiler
Company, Inc. or its representative the parts claimed to be defective and, if
requested by U.S. Boiler Company, Inc., to ship said parts prepaid to Burnham
Hydronics at the above address for inspection or repair. In addition, the
homeowner agrees to make all reasonable efforts to settle any disagreement
arising in connection with his claim before resorting to legal remedies in the
courts.
1. This warranty does not cover expenses for removal or reinstallation. The
homeowner will be responsible for the cost of removing and reinstalling
the defective part or its replacement and all labor and material connected
therewith. Replacement material will be invoiced to the distributor in the
usual manner and will be subject to adjustment upon proof of defect.
2. This warranty, in no way, can be considered as a guarantee of
workmanship of an installer connected with the installation of the U.S.
Boiler Company, Inc. boiler or as imposing on U.S. Boiler Company, Inc.
liability of any nature for unsatisfactory performance as a result of faulty
workmanship in the installation, which liability is expressly disclaimed.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY
ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
3. This warranty will not be applicable if the boiler is used or operated
over its rated capacity; or installed for uses other than home heating;
or is not maintained in accordance with U.S. Boiler Company, Inc.
recommendation or accepted good practice as determined by hydronics
industry standards.
4. This warranty will not be applicable if the boiler has been damaged as a
result of being improperly serviced or operated, including but not limited
to the following: operated with insufcient water, allowed to freeze; subject
to ood conditions; or operated with water conditions and/or fuels or
additives which cause unusual deposits or corrosion in or on the heat
exchanger.
|