MODEL
AR-C160
DIGITAL FULL COLOR
COPYING MACHINE
OPERATION MANUAL
Page
• GETTING STARTED
• MAKING COPIES
• SPECIAL FUNCTIONS
• SUPPLIES
1-1
2-1
3-1
4-1
5-1
• COPIER TROUBLE?
• GENERAL
INFORMATION
6-1
• OPTIONAL EQUIPMENT 7-1
Digital
COLOR COPY SAMPLES
The following pages contain samples of the various color copying functions described in this manual. They are
designed to demonstrate the wide range of capabilities and applications for the Sharp AR-C160 digital full color
copyingmachine.
Notethatthesamplesshownonpage1topage8arenot actualcopiesfromtheAR-C160copier.Thecolorsdisplayed
may differ from those of actual copies.
Color Copying with Special Features
1. Single color copying (See page 3-26.)
The single color function is used to produce copies using a selected single color.
Original
Red
Green
Blue
Purple
Orange
Brown
1
2. Neg./Pos. Reverse (See page 3-28.)
TheNEG./POS.REVERSEfunctionisusedtotransformacolororiginalintoits complementarycolors.Ifthisfunction
is selected in the black/white mode, the black and white areas of the original will be reversed.
Original
Colorcopy
Black/white copy
3. Photo repeat (See page 3-32.)
PHOTO REPEAT is used to produce multiple copies of a photo on a single sheet of copy paper.
Copy (8-1/2" x 11")
Original (3" x 5")
Copy (11" x 17")
Original (5" x 7")
2
4. Multi-page Enlargement (See page 3-36.)
This function is used to enlarge an original image to a size larger than 11" x 17" and to print portions of the image onto
multiple sheets of paper.
Copies (2 sheets of 11" x 17")
Original (8.5" x 11")
Copies (4 sheets of 11" x 17")
Original (11" x 17")
3
Adjustments for Color Copying
1. Exposure adjustments (See page 2-16.)
Exposure selections for this copier should be selected according to the type of originals being copied: TEXT/PRTD.
PHOTO, TEXT/PHOTO, TEXT, PHOTO, PRINTED PHOTO or MAP. Also COLOR TONE ENHANCEMENT can be
specified.
Text/prtd. photo mode, Text/photo mode:
Text mode:
This mode is useful for enhancing low density
areas of an original or suppressing high density
background areas.
These modes provide the best balance for copying
originals which contain text, printed photos and photos.
KEY OPERATOR CODE NUMBER
Akeyoperatorcodenumbermustberegistered
beforeakeyoperatorprogramcanbeused. The
key operator must remember this number. Only
this registered number will allow access to
the key operator programs.
Registering the key operator code number.
1 Press the CUSTOM SETTINGS key.
Photo mode:
Printed photo mode:
C
h
r
.
n
t
s
i
m
y
l
o
s
h
E
This mode provides the best quality reproduction of
photographs with fine detail.
This mode is useful for copying printed photo-
graphs.
Color tone enhancement:
This mode is used to make full color image more vivid.
Original
Copy
4
2. RGB Adjust (See page 3-16.)
RGBadjustmentsfunctiontoincreaseordecreasetheoverallamountofasingleprimarycolor.Theamountofchange
dependsuponthecharacteristicsoftheparticularoriginalbeingcopied.Generally,lightertonedareaswillbeaffected
to a greater degree than will darker toned areas.
Original
Red +
Green+
Blue +
Red-
Green-
Blue -
5
3. Sharpness (See page 3-18.)
This function is used to sharpen or soften image outlines.
Original
Softer
Sharper
4. Suppress background (See page 3-20.)
This copier can suppress unnecessary background colors on the original image when copying. This function is used
to adjust the density level of background colors to be erased.
Original
Copy
6
5. Color Balance (See page 3-22.)
The Color Balance function allows the density of colors to be adjusted. Adjusted color samples are shown below.
Original
Cyan adjustment +
Magenta adjustment +
Yellow adjustment +
Black adjustment +
Yellow adjustment -
Black adjustment -
Magentaadjustment-
Cyanadjustment-
7
6. Brightness/intensity/contrast (See page 3-24.)
Thiscopierallowsthelevelofbrightness,intensityorcontrastofimagestobeadjusted.Ifbrightnessisselected,color
tone can be darkened or lightened. If intensity is selected, the level of color saturation can be modified between vivid
and dull. If contrast is selected, the contrast between two image areas can be adjusted higher or lower.
Original
Brightness +
Intensity +
Contrast +
Brightness -
Intensity -
Contrast -
8
CONTENTS
Page
Page
●
●
INTRODUCTION ....................10
IMAGE EDITING FUNCTIONS ........ 3-26
Single color ...................... 3-26
Neg./pos. reverse ................. 3-28
Mirror image ..................... 3-30
Photo repeat ..................... 3-32
11x17 full-bleed ................... 3-34
Multi-page enlargement ............. 3-36
Extra size ....................... 3-38
●
USING THIS MANUAL ................10
CHAPTER 1
GETTING STARTED
●
●
●
INSTALLATION REQUIREMENTS ...... 1-2
CAUTIONS ....................... 1-3
POWER ON AND OFF............... 1-5
Power save modes ................. 1-6
INFORMATION FUNCTION ........... 1-7
USING THE TOUCH PANEL .......... 1-8
How to use the touch panel ........... 1-8
Selection of function ................. 1-8
Function setting icons ............... 1-9
COPY MODE AND PRINT MODE...... 1-10
Printing documents from the computer .. 1-10
Using the operation panel in the
CHAPTER 4
SUPPLIES
●
●
●
PAPER .......................... 4-2
Types and sizes of copy paper ......... 4-2
Loading copy paper ................. 4-2
ADDING TONER ................... 4-5
USED TONER DISPOSAL ............ 4-8
STORAGE OF SUPPLIES ............ 4-9
●
●
●
●
print mode ....................... 1-11
How to select the paper type for the
bypass tray ...................... 1-11
General operation steps for the
scanner use ..................... 1-12
CHAPTER 5
COPIER TROUBLE?
●
MISFEED REMOVAL................ 5-2
●
MAINTENANCE REQUIRED ......... 5-11
●
TONER COLLECTING CONTAINER OF
TRANSFER UNIT ................. 5-12
TROUBLESHOOTING .............. 5-13
CHAPTER 2
●
MAKING COPIES
●
AUDITING ACCOUNTS .............. 2-2
●
COPYING FROM THE DOCUMENT
GLASS .......................... 2-3
USING THE RADF ................. 2-6
REDUCTION/ENLARGEMENT/ZOOM .. 2-11
SPECIAL PAPERS (manual feed) ...... 2-14
Two-sided copying with bypass tray .... 2-15
EXPOSURE ADJUSTMENTS......... 2-16
JOB MEMORY ................... 2-18
INTERRUPTING A COPY RUN ....... 2-20
CHAPTER 6
GENERAL INFORMATION
●
●
●
●
PART NAMES AND FUNCTIONS ....... 6-2
Exterior .......................... 6-2
Interior .......................... 6-3
Operation panel .................... 6-4
Touch panel (Basic screen) ........... 6-5
●
●
●
●
USER MAINTENANCE .............. 6-6
●
TOUCH PANEL CONTRAST
ADJUSTMENT .................... 6-7
SPECIFICATIONS .................. 6-8
●
CHAPTER 3
SPECIAL FUNCTIONS
●
XY ZOOM ........................ 3-2
MARGIN SHIFT.................... 3-4
ERASE .......................... 3-6
DUAL PAGE COPYING .............. 3-8
CENTERING ..................... 3-10
TRANSPARENCY FILM WITH
INSERT SHEETS ................. 3-12
COVERS ....................... 3-14
COLOR ADJUSTMENTS ............ 3-16
RGB adjust ...................... 3-16
Sharpness....................... 3-18
Suppress background .............. 3-20
Color balance .................... 3-22
Brightness/intensity/contrast .......... 3-24
CHAPTER 7
OPTIONAL EQUIPMENT
●
●
●
●
●
●
SYSTEM CONFIGURATION .......... 7-2
20-BIN STAPLE SORTER (AR-SS2) ..... 7-3
LARGE CAPACITY TRAY (AR-LC2N) ... 7-15
FINISHER (AR-FN4) ............... 7-19
●
●
●
●
●
9
INTRODUCTION
The AR-C160 copier is a digital color image processing copier which provides
high productivity at a color copy speed of 16 copies/minute and convenient
features including intelligent image-editing functions.
Amongst its many useful features and functions are the document feeder
(optional), photocopying, internalauditor, andvariousspecialfunctionssuchas
dual page copying, margin shift, erase, XY zoom, and NEG./POS. reverse
functions.Thiscopiercanbeequippedwithanoptionallargecapacitytraywhich
holds 3,000 sheets of copy paper. The machine can also be equipped with an
optional staple sorter or an optional finisher with offset stack function to provide
finished copy sets ready for distribution.
Thiscopierwasalsodesignedwitheaseofuseinmind.Theeasy-to-understand
operationpanelwithtouchpanelsystemandINFORMATIONfunctionwillguide
the user through most operations. To gain the maximum benefit of all the copier
features,however,itisrecommendedthatusersfirstreadthismanualtobecome
familiar with all the copier features.
NOTES:
●
This manual describes only copier features. For a description of optional
printer features, see the separate relevant manual. A brief description of
operation in the PRINT mode is, however, written on pages 1-10 to 1-12.
This copier can be equipped with an optional document cover or reversing
●
automatic document feeder (RADF). The illustrations in this manual are
mainly for the copier with an optional RADF installed.
The display on the touch panel varies with installation of optional equipment.
●
Theillustrationsofthetouchpanelinthismanualaremainlyforthecopierwith
an optional RADF (AR-RF1) installed.
USING THIS MANUAL
This manual is intended as an operation guide for both general users and key
operators.
For General Users
It is recommended that you read the GETTING STARTED, MAKING COPIES,
and SPECIAL FUNCTIONS sections to become familiar with the available
features and functions of your copier. Then refer to the manual as needed to
become thoroughly familiar with those features you will normally use.
For Key Operators
Please read all sections thoroughly to become familiar with all features and
functions of your copier. Throughout the manual, information which is relevant
to key operator functions is noted by “★ KEY OPERATOR.” Please pay close
attentiontothesenotesandtotheSUPPLIES,COPIERTROUBLE?,GENERAL
INFORMATION, and OPTIONAL EQUIPMENT sections so you can ensure
smooth and efficient operation of your machine.
A separate KEY OPERATOR’S GUIDE has been written especially for you. It
containstheprogramsandprogramminginformationthatwillenableyoutotailor
functions for maximum benefit to your company.
10
CHAPTER 1
GETTING STARTED
This chapter describes the basic information on the use of this copier.
Page
●
INSTALLATION REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . 1-2
●
CAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
●
POWER ON AND OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Power save modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
●
INFORMATION FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
●
USINGTHETOUCH PANEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
How to use the touch panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
Selection of function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
Function setting icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
●
COPY MODE AND PRINT MODE . . . . . . . . . . . . . . . . . . . . . . . 1-10
Printing documents from the computer . . . . . . . . . . . . . . . . . . . . 1-10
Using the operation panel in the print mode . . . . . . . . . . . . . . . . 1-11
How to select the paper type for the bypass tray . . . . . . . . . . . . 1-11
General operation steps for the scanner use . . . . . . . . . . . . . . . 1-12
1-1
INSTALLATION REQUIREMENTS
Toensuresafetyandpropermachineperformance,pleasenotethefollowing
before initial installation and whenever the machine is to be relocated.
1. The copier should be installed near an accessible power outlet for easy
connection.
2. Be sure to connect the power cord only to a power outlet that meets the
specified voltage and current requirements.
Also make certain the outlet is properly grounded.
3. Do not install the machine where it is:
●
damp or humid,
●
exposed to direct sunlight,
●
extremely dusty,
●
poorly ventilated,
●
subjecttoextremetemperatureorhumiditychanges(e.g., nearanair
conditioner or heater).
4. Ensure that the area chosen for the machine location is level.
5. Besuretoallowtherequiredspacearoundthemachineforservicingand
proper ventilation.
11-13/16"
(30 cm)
23-5/8"
(60 cm)
11-13/16"
(30 cm)
23-5/8"
(60 cm)
A small amount of ozone is produced within the copier during operation.
The emission level is insufficient to cause any health hazard.
NOTE:
The present recommended long term exposure limit for ozone is 0.1 ppm
(0.2 mg/m3) calculated as an 8 hr. time-weighted average concentration.
However, sincethesmallamountthatisemittedmayhaveanobjectionable
odor, it is advisable to place the copier in a ventilated area.
1-2
CAUTIONS
1. Donottouchthephotoconductivedrumsorpapertransport.
Scratches or smudges on them will cause copy defects.
2. The fusing unit is extremely hot. Exercise care in this area.
Paper transport
Fusing unit
3. Do not look directly at the light source. Doing so may damage
your eyes.
4. Installation adjusters.
When moving the machine, be sure to raise the installation
adjusters. After moving the machine, lower the installation
adjusters until they reach the floor.
This copier contains fusing oil that is very slippery if leaked
on the floor. Ensure that the machine is located at level
positionandtakecareifitistobemovedthatoilleakagedoes
not occur.
Release
Lock
5. This copier is equipped with a forgery prevention feature. If paper
that closely resembles paper money is used as an original,
copying may not be performed properly.
Adjuster
“BATTERY DISPOSAL”
THIS MACHINE CONTAINS A MANGANESE DIOXIDE BATTERY WHICH MUST BE DISPOSED
OF PROPERLY. CONTACT YOUR SHARP DEALER OR SERVICER FOR INSTRUCTIONS.
This product utilizes tin-lead solder, and a fluorescent lamp containing a small amount of mercury.
Disposal of these materials may be regulated due to environmental considerations.
For disposal or recycling information, please contact your local authorities or the Electronics Industries
Alliance: www.eia.org
1-3
CAUTIONS
Cautions on laser
+10 nm
- 15 nm
Wave length
Pulse times
Output power
785 nm
(4.374 µs ±4.4 ns)/7 mm
0.20 mW - 0.45 mW
SAFETY PRECAUTIONS
This Digital Copier is rated Class 1 and complies with 21 CFR
1040.10 and 1040.11 of the CDRH standards. This means that
the copier does not produce hazardous laser radiation. For your
safety, observe the precautions below.
●
Do not remove the cabinet, operation panel or any other
covers.
●
The copier’s exterior covers contain several safety interlock
switches. Do not bypass any safety interlock by inserting
wedges or other items into switch slots.
Caution
Use of controls or adjustments or performance of procedures other
than those specified herein may result in hazardous radiation
exposure.
1-4
POWER ON AND OFF
The power switch is located on the left side of the copier. When the
power switch is turned to the “ON” position, the message “WARMING
UP. PLEASE WAIT.” will appear in the message display. Warming
up takes about 330 seconds. Once the copier is ready, the message
display will change to “READY TO COPY.”, and the START key
indicators will light up, indicating that copying is possible.
Ifthecopierhasbeenprogrammedintheauditingmode,themessage
“ENTERYOURACCOUNTNUMBER.-----”willappearafterwarming
up. Once a valid account number has been entered, copying will
become possible.
Power on
Power off
●
Be sure to extend the tray when paper sizes 8-1/2"
x 14" or larger are to be received.
1-5
POWER ON AND OFF
Power save modes
The copier has two power save modes to reduce overall power
consumptionandtherebyreducethecostofoperationandtoconserve
natural resources to help reduce environmental pollution. The two
power save modes are preheat mode and sleep mode.
★ KEY OPERATOR
The preheat activation time and the sleep activation time have been
preset at the factory to 15 min. for preheat mode and 60 min. for sleep
mode. These times can be changed as described in the key operator’s
guide. It is suggested that you set appropriate times according to the
actual usage of the copier.
Sleep mode
If the sleep mode is enabled, the copier will enter the mode once a
programmed length of time has elapsed without any copier
operation after the last copy of a run is made or the power is first
turned on. When the copier enters the sleep mode, the display on
the touch panel will disappear. In this condition, power is not
supplied to the fuser in the copier. To exit from the sleep mode,
press the COPY key.
★ KEY OPERATOR See page 25 of the KEY OPERATOR’S GUIDE for
setting the sleep mode timer. See page 30 of the KEY OPERATOR’S
GUIDE for enabling or disabling the sleep mode.
Preheat mode
The copier will enter the mode once the set time has elapsed without
any copier operation after the last copy of a run is made or power is
turned on.
When the copier enters the preheat mode, the message “PREHEAT
MODE. PLACE ORIGINALS.” will appear.
In this condition, the fuser in the copier is maintained at a lower heat
level thereby saving power. The preheat level is, however, high
enough to allow the copier to come to a ready condition or begin
copying approximately 30 seconds after any key input is made.
To copy from the preheat mode, make desired copier selections and
press a START key using the normal copying procedure.
★ KEY OPERATOR See page 26 of the KEY OPERATOR’S GUIDE for
As an ENERGY STAR® Partner,
SHARP has determined that this
product meets the ENERGY
STAR® guidelines for energy
efficiency.
information on setting the preheat mode.
1-6
INFORMATION FUNCTION
The information function provides a quick reference guide to the use
of the various features and functions of this copier. The information
mode can be entered when the copier is in the standby mode.
Press the INFORMATION ( ) key in the standby mode.
1
2
3
●
The screen for the information categories will appear.
INFORMATION
4
CUSTOM
SETTINGS
Select the “COPIER” key to display the first screen of
the copier feature items.
EXIT
INFORMATION
SELECT INFORMATION.
●
If the toner supply is low, press the ADDING TONER key for
toner replenishment instructions.
COPIER
ADDING NER
Select the feature you would like to know about by
pressing a copier feature item key on the touch panel.
EXIT
INFORMATION
MAKING 2-SIDED COPIES (2-SIDED COPY)
●
Ifthefeatureyouwouldliketoknowaboutisnotdisplayedonthe
SORTING COPIES TO SETS OR STAPLING
FINISHED SETS OCOPIES (OUTPUT)
1/5
touch panel, press the scroll (
the feature is displayed.
) key on the touch panel until
USING THE DOCUMEEDER
(
DOCUMENT FE
●
If a copier feature item key is pressed, the description for that
feature will appear. Use the scroll ( ) key to display additional
REDUCTION/EM
(COPY RATIO
informationuntilallinformationforthatfeaturehasbeendisplayed.
STORING FREOB PROGRAMS
(PROGRAM)
●
●
To return to the copier feature item screen, press the “INDEX”
key.
To exit the INFORMATION mode, press the “EXIT” key on the
touch panel.
1-7
USING THE TOUCH PANEL
How to use the touch panel
You can set or cancel a function displayed on the touch
READY TO COPY.
panel by pressing (touching) a key with a finger. The touch
key operation can be confirmed with a beep tone (and
highlighting of the touch key).
PAPER TYPE
16~28 lbs.
1
1.8/ 11
2
28+~35 lbs.
35+~75 lbs.
TRANSPARENCY
2.11 17
3.84
★ KEY OPERATOR For the beep tone to be heard, the beep tone must be
enabledbyakeyoperatorprogram.Seepage27oftheKEYOPERATOR’S
GUIDE.
AUTO
EXPOSURE
100%
COPY RATIO
P
A grayed out function key represents unavailability of that
function. Ifagrayedoutkeyispressed, twoshortbeepswill
sound.
RECALL
STOELETE
Selection of function
To register the selected settings for a function, press the
“OK” key on the setting screen. The settings indicated by
ahighlighteddisplaywillberegisteredasaselectedfunction.
OK
OK
CANCEL
ERASE
~1)
1/
nch
EDGE ERASE
CENTER ERASE
EDGE+CENTER
ERASE
Some special functions can be selected by pressing the
relevant keys on the SPECIAL MODES screen (page 3-4) or
on the IMAGE EDIT menu (page 3-26) to highlight the keys.
To cancel these functions, press the relevant keys again to
return the keys to the normal display. These functions are:
Dual page copying, Centering, Transparency inserts, Neg./
pos. reverse, Mirror image, and 11x17 full-bleed.
READY TO COPY.
SPECIAL MODES
OK
DUAL PAGE
COPY
MARGIN SHIFT
CENTERING
COVERS
ERASE
TRANSPARENCY INS
COLOR
IMAGT
ADJUSTMENTS
1
AUTO
AUTO
8/ 11
2
1
EXPOSURE
PAPER SELECT
1-8
USING THE TOUCH PANEL
Function setting icons
Icons representing special functions which have been
selected will appear on the basic screen. The functions and
their associated icons are listed below.
READY TO COPY.
The content of the icons of functions indicated by (*) will
vary depending upon particular settings selected for these
functions. The other functions are on or off type functions
and have no associated setting screens.
5
1
1.
82 11
2.
11 17
1
OK
OK
CANCEL
ERASE
(0~1)
1/2
inch
EDGE ERASE
CENTER ERASE
EDGE+CENTER
ERASE
* Margin shift (p.3-4)
* Erase (p.3-6)
* Single color (p.3-26)
Neg./pos. reverse (p.3-28)
Mirror image (p.3-30)
Dual page copying (p.3-8)
Centering (p.3-10)
* Photo repeat (p.3-32)
Transparency film with insert sheets
(p.3-12)
11 x 17 full-bleed (p.3-34)
Multi-page enlargement (p.3-36)
Extra size (p.3-38)
* Covers (p.3-14)
Color adjustments (p.3-16)
1-9
COPY MODE AND PRINT MODE
An optional power supply kit (AR-PX4) and an optional printer
controller board (AR-PE2) must be installed to use this copier as a
printer.
Printing documents from the computer
In most cases, it is not necessary to use the operation panel when
printing documents from the computer. When a document is sent to
the printer from the computer, the printer will automatically print the
document. However, following the procedure specified below can
help the user ensure that documents are printed accurately. The
procedure assumes that the printer has been properly connected to a
computer, and that a printer driver has been installed.
Check the operation panel to confirm that the ON LINE
indicator is lit. If the ON LINE indicator is not lit, press
1
the PRINT key to select the print mode and then press
the “ONLINE/OFFLINE” key on the touch panel to set
the printer to the on-line condition.
Check the paper tray(s) to ensure that the desired
paper is loaded.
2
Using the computer and any appropriate application
software, load the document to be printed, set any
3
desired features using the installed printer driver, and
givethecommandtoprintthedocument. Ifnecessary,
refertothedocumentationforthecomputerand/orthe
applicationsoftwareforhelponissuingthenecessary
commands.
The printer will print the document.
4
NOTE:
When the printer feature is used, if the ON LINE indicator is
blinking red, this machine cannot execute printing from some
cause. PressthePRINTkeytoselecttheprintmode. Amessage
indicatingthecausefortheerrorsuchasnopaperornotonerwill
be displayed. Check the message and take proper measures.
Selecting the on-line mode
If the printer is in the off-line mode, printing cannot be performed. To
select the on-line mode, follow the procedure below.
If the printer is in the copy mode, press the PRINT key
to select the print mode.
1
●
The basic screen of the print mode will appear.
Press the “ONLINE/OFFLINE” key on the touch panel
to switch the printer to the on-line mode.
2
To return to the copy mode, press the COPY key.
3
1-10
COPY MODE AND PRINT MODE
Using the operation panel in the print mode
The operation panel provides access to many of the printer’s features
and functions. The basic procedure to access the printer’s features
and functions is shown below.
If the printer is in the copy mode, press the PRINT key to
READY TO PRINT.
select the print mode.
1
●
The basic screen of the print mode will appear.
Press the “ONLINE/OFFLINE” key on the touch panel to
switch the printer to the off-line mode.
DUPLEX
1
1.
11
82
2
3
4
2.
11 17
1
3.
82 14
ONLINE
100%
Press the “fiery” key on the touch panel.
PAPER SELECT
OFFLINE
Use the keys on the touch panel to select the desired
operation.
●
For details of the functions in the print mode, see the printer
operation manual.
●
To return to the printer basic screen, press the return (
key.
)
FIERY PRINTER SCREEN
AR-C160 PRINTER
idle
5348MB
V1.0
info
How to select the paper type for the bypass tray
Before the paper type can be selected, paper must be placed in the
bypass tray and the key operator program “Enable Bypass-Tray
Type Detection” must be used to enable the selection (see page 33 of
the KEY OPERATOR’S GUIDE). Proceed as follows.
Press the PRINT key to select the print mode.
1
2
Press the “ONLINE/OFFLINE” key to enter the off-line
mode.
Press the “PAPER” key.
3
4
Use the touch panel to enter the paper type to match the
paper set in the bypass tray.
Press the “ONLINE/OFFLINE” key to restore the on-line
mode.
5
1-11
COPY MODE AND PRINT MODE
General operation steps for using the scanner
To scan, process or edit document images by using the scanning
feature of the machine, Adobe Photoshop 5.0 or later is needed.
Install the required driver software in your computer in
accordance with the operation manual for the Printer
Controller.
1
Press the PRINT key to display the print mode screen.
2
3
Check the operation panel to confirm that the ONLINE
keyisselected.Ifnot,touchthe“ONLINE/OFFLINE”key
to select the online status.
Place the original on the document glass or in the
document feeder (optional).
4
NOTE:
Even if multiple originals are set in the document feeder images
must be processed one at a time.
Acquire the image using the application software. For
the details, refer to the operation manual supplied with
the application software.
5
6
Editorstorethescannedimage.Refertotheinstructions
supplied with the application software for details.
NOTE:
For detailed instructions on using the machine as a scanner, refer
to the operation manual supplied with the Printer Controller.
1-12
CHAPTER 2
MAKING COPIES
This chapter describes the basic copying functions such as normal
copying, reduction/enlargement, and exposure adjustments.
Page
●
AUDITING ACCOUNTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
●
COPYING FROMTHE DOCUMENT GLASS . . . . . . . . . . . . . . . 2-3
●
USINGTHE RADF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
●
REDUCTION/ENLARGEMENT/ZOOM . . . . . . . . . . . . . . . . . . . 2-11
●
SPECIAL PAPERS (manual feed). . . . . . . . . . . . . . . . . . . . . . . 2-14
Two-sided copying with bypass tray . . . . . . . . . . . . . . . . . . . . . . 2-15
●
EXPOSURE ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
●
JOB MEMORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
●
INTERRUPTING A COPY RUN . . . . . . . . . . . . . . . . . . . . . . . . . 2-20
2-1
AUDITING ACCOUNTS
If this copier has been programmed in the auditing mode, it will not function until an assigned 5-digit account number
has been entered.The auditing mode can be set for both the color and black/white (B/W) copy modes or for only the
color copy mode.
★ KEY OPERATOR See page 9 of the KEY OPERATOR’S GUIDE for setting the auditing mode.
If the auditing mode has been set for both the color and B/W copy
modes, the initial status of the message display will be:
ENTER YOUR ACCOUNT NUMBER. -----
If the auditing mode has been set for only the color copy mode, the
following display will appear when the AUDIT key or the COLOR
COPY START (
) key is pressed.
ENTER YOUR ACCOUNT NUMBER
FOR COLOR COPYING.
N
INTERRUPT
CLEAR
1
4
2
5
3
6
-----
●
●
Enter your account number using the 10-key pad.
As each digit is entered, the dashes in the display will change to
asterisks.
CA
ALL
7
9
The following message will appear after the number is entered.
AUDIT
PROGRAM
C
CLEAR
ACCOUNT STATUS: COPIES MADE /REMAINING
B/W:000,000/000,000 CL:000,000/000,000
P
“COPIES REMAINING” will appear only if account limit has been
set using a key operator program.
★ KEY OPERATOR
See page 16 of the KEY OPERATOR’S
GUIDE for account limit settings.
●
●
Themessagewillbedisplayedforseveralseconds,thenchange
to the following message.
READY TO COPY.
When a copy run is performed, the following message will
appear.
READY TO COPY.
PRESS [AUDIT] WHEN FINISHED.
●
In the interrupt copy mode (see page 2-20), the following
message will appear instead of the message above.
READY TO COPY. WHEN COPYING IS
FINISHED, PRESS [INTERRUPT].
NOTE:
Ifanunassignednumberisentered,themessagedisplaywillshow
“ENTER YOUR ACCOUNT NUMBER.-----”, indicating that the
number was not accepted.
When the key operator program of account number security has
been set:
If an unassigned number is entered three successive times, the
copier will not accept another number for one minute, and the
following message will appear.
PLEASE SEE YOUR KEY OPERATOR FOR
ASSISTANCE.
★ KEY OPERATOR
See page 17 of the KEY OPERATOR’S
GUIDE for account number security.
2-2
COPYING FROM THE DOCUMENT GLASS
●
Use the document glass for copying single originals,
bounddocuments,andotheroriginalsthatcannotbeset
in the optional RADF.
Image loss (max. 13/64" (5 mm)) can occur along
the leading edge of the copies. Image loss (max. 9/
32" (7mm)) can occur along the trailing edge of the
copies. Also image loss (max. 1/4" (6 mm) in total)
can occur along the other edges of the copies.
●
Only 1-sided to 1-sided and 1-sided to 2-sided
copying can be selected when copying from the
document glass.
●
Duplex copying will not work when a non-standard
sized paper or 5-1/2" x 8-1/2"R paper is used.
2-sided to 2-sided or 2-sided to 1-sided copying
●
cannot be selected when copying from the
document glass. These operations can, however,
be performed simply by turning over the original
manually.
1-sided copies of 1-sided originals
Open the document cover and place an original face
down on the document glass, using the centering scale
to position it.
Original size detector
1
●
Whencopyingmulti-pagedocuments,copyfromthelastpageto
the first page.
NOTE:
Do not place objects under the original size detector, because they
may damage it.
Centering scale
Close the document cover.
●
Theoriginalsizewillbeindicatedonthetouchpanel,andthepaper
2
3
traywiththecorrespondingpapersizewillbeautomaticallyselected.
READY TO COPY.
Ensure that the 1-sided to 1-sided copying mode is
selected on the touch panel.
1
ORIGINAL
82 11
●
When no icon is displayed in the area indicated in the illustration
(
), the 1-sided to 1-sided copying mode is selected.
1
1.
82 11
2.
11 17
●
If the 1-sided to 1-sided mode is not selected, press the
2-SIDED COPY key and then press the 1-sided to 1-sided key
1
3.
82 14
1
AUTO
AUTO
8/ 11
2
100%
(
) on the touch panel. Press the “OK” key to return to the
EXPOSURE
PAPER SELECT
COPY RATIO
basic screen.
N
Use the 10-key pad to enter the desired number of
copies.
INTERRUPT
1
4
2
5
8
0
3
6
4
●
The number will be shown in the copy quantity display of the
touch panel.
CLEAR
ALL
CA
●
●
A single copy can be made with the initial setting, i.e., when “0”
is displayed.
7
9
UsetheCLEAR( )keytocancelanentryifamistakeismade.
C
AUDIT
PROGRAM
C
CLEAR
P
2-3
COPYING FROM THE DOCUMENT GLASS
Press the COLOR COPY START (
) key or BLACK
INTERRUPT
CLEAR
COPY START (
) key.
5
3
6
●
To perform color copying, press the COLOR COPY START
) key. To perform black/white copying, press the BLACK
COPY START ( ) key.
(
CA
ALL
●
●
The number in the copy quantity display will decrease by 1 each
time a copy is made. To repeat the same copy sequence with a
different original, simply replace the original and press the
START key.
9
PROGRAM
C
CLEAR
P
CA
To cancel a copy run, press the CLEAR ALL ( ) key. Copying
willstopandthenumberinthecopyquantitydisplaywillbereset
to 0.
2-sided copies from 1-sided originals
Tocopyinthe1-sidedto2-sidedcopymode,anoptionalduplexmodule
(AR-DU2N) must be installed.
For an odd number of originals:
Original size detector
Set the last page of the document onto the document
glass, and copy it in the 1-sided to 1-sided mode.
1
Centering scale
Press the 2-SIDED COPY key.
2
3
2-SIDED
COPY
OUTPUT
Pressthe
(EVENNUMBERORIGINALS)keyonthe
READY TO COPY.
2-SIDED COPY
touch panel and then press the “OK” key.
OK
PRE-COT
EVEN MBER ODD NUMBER
R
ORIALS
ORIGINALS
S
1
1
A
AUTO
8/
8/ 11
2
O
EXP
PAPER SELE2
2-4
COPYING FROM THE DOCUMENT GLASS
Copy the reminder of the originals in reverse order.
●
When making color copies in the duplex mode or making B/W
4
INTERRUPT
CLEAR
3
6
copies in the duplex mode onto paper 8-1/2" x 14" or larger, only
one copy per original can be made. Even if a multiple number of
copiesisset,thenumberwillbechangedto1whenaSTARTkey
is pressed.
CA
ALL
9
PROGRAM
C
CLEAR
P
For an even number of originals:
Press the 2-SIDED COPY key.
2-SIDED
COPY
1
2
OUTPUT
Pressthe
(EVENNUMBERORIGINALS)keyonthe
READY TO COPY.
2-SIDED COPY
touch panel and then press the “OK” key.
OK
PRE-COT
EVEN MBER ODD NUMBER
R
ORIALS
ORIGINALS
S
1
1
A
AUTO
8/
8/ 11
2
O
2
Copy the originals in reverse order.
●
When making color copies in the duplex mode or making B/W
3
INTERRUPT
3
copies in the duplex mode onto paper 8-1/2" x 14" or larger, only
one copy per original can be made. Even if a multiple number of
copiesisset,thenumberwillbechangedto1whenaSTARTkey
is pressed.
6
CLEAR
CA
ALL
9
PROGRAM
C
CLEAR
P
2-5
USING THE RADF
●
This copier can be equipped with an optional reversing
automatic document feeder (RADF).
The RADF will handle multiple originals.
Duplex copying will not work when a non-standard
sized paper or 5-1/2" x 8-1/2" paper is used.
Imageloss(max. 13/64"(5mm))canoccuralongthe
leading edge of the copies. Image loss (max. 9/32"
(7mm)) can occur along the trailing edge of the
copies. Also image loss (max. 1/4" (6 mm) in total)
can occur along the other edges of the copies.
The RADF can handle a maximum of 50 originals of
5-1/2" x 8-1/2" to 8-1/2" x 11" sizes and 30 originals
of 8-1/2" x 14" to 11" x 17" sizes.
●
●
Before loading originals into the document feeder
tray, be sure to remove any staples or paper clips
from them.
Damaged or crumpled originals or originals which
●
●
have been folded may misfeed in the RADF or cause
incorrectsizedetection.Itisrecommendedthatthese
becopiedfromthedocumentglassandthecopiesbe
●
used as original documents.
When feeding originals which have closely spaced
2-sided to 1-sided copying and 2-sided to 2-sided*
copying can be performed.
●
binding holes punched along an edge, place the
originalssothatthepunchededgeispositionedtothe
right or along the side guides.
Specialoriginalssuchastransparencyfilmandtracing
papershouldnotbefedfromtheRADF,butshouldbe
placed on the document glass.
* For 2-sided to 2-sided copying, an optional duplex
module (AR-DU2) must be installed.
●
The originals must be set face up in the document
●
feeder tray.
●
Different size originals with the same width can be
placedinthedocumentfeedertrayandautomatically
copied onto copy paper of their respective sizes.
The automatic copy ratio selection will not function in
this case.
Stream feeding mode
If the stream feeding mode has been enabled using a key operator
program,themessage“NEWLYPLACEDORIGINALSWILLBEFED
AND COPIED AUTOMATICALLY.” will appear and the original feed
indicator will continue to blink for approximately 5 seconds after
feedingofalloriginalsiscompleted.Whilethismessageisdisplayed,
any new originals placed in the document feeder tray will be fed and
copied automatically.
★ KEY OPERATOR See page 24 of the KEY OPERATOR’S GUIDE
for information on setting the stream feeding mode.
2-6
USING THE RADF
Original
Copy
1-sided copies of 1-sided originals
Adjusttheoriginalguidestothesizeoftheoriginalsand
set the originals face up in the document feeder tray.
1
●
The original size will be indicated on the touch panel, and the
papertraywiththecorrespondingpapersizewillbeautomatically
selected.
●
Be sure to remove any original from the document glass before
setting the originals in the document feeder tray. If an original is
left on the document glass, the original reminder indicator will
blink. Removetheoriginalfromthedocumentglassinthiscase.
●
If copy paper of the required size is not installed in any of the
trays, the following message will appear.
LOAD " x " PAPER.
If a tray of the required size is not installed, use the bypass tray
andpressthe“PAPERSELECT”keyonthetouchpaneltoselect
the bypass tray.
●
To copy onto a different size paper, use the “PAPER SELECT”
key to make the selection.
Ensure that the 1-sided to 1-sided copying mode is
selected on the touch panel.
READY TO COPY.(DOCUMENT FEEDER MODE)
ORIGINAL
2
3
1
82 11
●
When no icon is displayed in the area indicated in the illustration
(
), the 1-sided to 1-sided copying mode is selected.
●
If the 1-sided to 1-sided mode is not selected, press the
2-SIDED COPY key and then press the 1-sided to 1-sided key
1
1.
82 11
2.
11 17
1
3.
82 14
(
) on the touch panel. Press the “OK” key to return to the
1
AUTO
AUTO
8/ 11
2
100%
basic screen.
EXPOSURE
PAPER SELECT
COPY RATIO
N
Use the 10-key pad to enter the desired number of
copies.
INTERRUPT
1
4
2
5
8
0
3
6
●
The number will be shown in the copy quantity display of the
touch panel.
CLEAR
ALL
●
UsetheCLEAR( )keytocancelanentryifamistakehasbeen
CA
C
made.
7
9
AUDIT
PROGRAM
C
CLEAR
P
Press the COLOR COPY START (
) key or BLACK
INTERRUPT
CLEAR
COPY START (
) key.
4
3
6
9
●
To perform color copying, press the COLOR COPY START
) key. To perform black/white copying, press the BLACK
COPY START ( ) key.
(
CA
ALL
●
CA
To cancel a copy run, press the CLEAR ALL ( ) key. Copying
willstopandtheRADFwilloutputanyoriginalswhichhavebeen
fed. Also, the number in the copy quantity display will be reset to
0.
PROGRAM
C
CLEAR
P
2-7
USING THE RADF
2-sided copies from 1-sided originals
Originals (1-sided)
Copy (2-sided)
Tocopyinthe1-sidedto2-sidedcopymode,anoptionalduplexmodule
(AR-DU2N) must be installed.
Adjusttheoriginalguidestothesizeoftheoriginalsand
set the originals face up in the document feeder tray.
1
Maximum height
line
Press the 2-SIDED COPY key.
2
3
2-SIDED
COPY
OUTPUT
Ifthenumberoforiginalsisknown, usethe
(EVEN
NUMBER ORIGINALS) key or
(ODD NUMBER
ORIGINALS) key on the touch panel, then proceed to
step 4. If the number of originals is not known, select
“PRE-COUNT” for an automatic count by the RADF and
READY TO COPY.(DOCUMENT FEEDER MODE)
2-SIDED COPY
OK
press the COLOR COPY START (
) key or BLACK
PRE-COUNT
COPY START (
) key.
●
The following message will appear.
EVEN MBER ODD NUMBER
PRE-COUNT MODE
NUMBER OF ORIGINALS IS **.
ORIALS
ORIGINALS
1
A
AUTO
8/ 11
2
100%
●
●
If the number of originals exceeds the limit, other messages will
appear .
READY TO COPY.(DOCUMENT FEEDER MODE)
2-SIDED COPY
When the count is complete and the number is known, replace
the originals in the document feeder tray and select “EVEN
NUMBER ORIGINALS” or “ODD NUMBER ORIGINALS” as
above.
OK
PRE-COT
EVEN
Press the “OK” key.
EVEN NUMBER ODD NUMBER
4
5
ORIGINALS
ORIGINALS
1
AUTO
8/ 11
2
AUTO
Enter the desired number of copies.
●
When making color copies in the duplex mode or making B/W
copies in the duplex mode onto paper 8-1/2" x 14" or larger, only
one copy per original can be made. Even if a multiple number of
copiesisset,thenumberwillbechangedto1whenaSTARTkey
is pressed.
INTE
1
4
2
5
8
0
3
TERRUPT
6
CLE
CLEAR
ALL
CA
AL
Press the COLOR COPY START (
) key or BLACK
7
9
COPY START (
) key.
6
C
AUDIT
PROGRAM
C
●
To perform color copying, press the COLOR COPY START
) key. To perform black/white copying, press the BLACK
COPY START ( ) key.
PCLEAR
CL
(
●
To cancel a copy run during duplex copying, press the CLEAR
CA
ALL ( ) key.
2-8
USING THE RADF
2-sided copies from 2-sided originals
Original (2-sided)
Copy (2-sided)
Tocopyinthe2-sidedto2-sidedmode,anoptionalduplexmodule(AR-
DU2N) must be installed.
Adjusttheoriginalguidestothesizeoftheoriginalsand
set the originals face up in the document feeder tray.
1
Maximum height
line
Press the 2-SIDED COPY key.
2
3
4
2-SIDED
COPY
OUTPUT
READY TO COPY.(DOCUMENT FEEDER MODE)
2-SIDED COPY
Press the
key on the touch panel.
OK
PRE-COUNT
EVEN NUMBER ODD NUMBER
ORIGINALS
ORIGINALS
1
AUTO
AUTO
8/
100%
READY TO COPY.(DOCUMENT FEEDER MODE)
2-SIDED COPY
Press the “OK” key.
OK
PRE-COT
EVEN NUMBER ODD NUMBER
ORIGINALS
ORIGINALS
1
Enter the desired number of copies.
AUTO
AUTO
8/ 11
2
●
When making color copies in the duplex mode or making B/W
5
6
copies in the duplex mode onto paper 8-1/2" x 14" or larger, only
one copy per original can be made. Even if a multiple number of
copiesisset,thenumberwillbechangedto1whenaSTARTkey
is pressed.
INTE
1
4
2
5
8
0
3
TERRUPT
6
Press the COLOR COPY START (
) key or BLACK
CLE
CLEAR
ALL
CA
AL
COPY START (
) key.
7
9
●
To perform color copying, press the COLOR COPY START
) key. To perform black/white copying, press the BLACK
COPY START ( ) key.
C
AUDIT
PROGRAM
C
CL
(
PCLEAR
●
To cancel a copy run during duplex copying, press the CLEAR
ALL ( ) key.
CA
2-9
USING THE RADF
1-sided copies from 2-sided originals
Original (2-sided) Copies (1-sided)
Adjusttheoriginalguidestothesizeoftheoriginalsand
set the originals face up in the document feeder tray.
1
Maximum height
line
Press the 2-SIDED COPY key.
2
3
4
2-SIDED
COPY
OUTPUT
Press the
key on the touch panel.
READY TO COPY.(DOCUMENT FEEDER MODE)
OK
2-SIDED COPY
PRE-COUNT
EVEN NUMBER ODD NUMBER
ORIGINALS
ORIGINALS
1
AUTO
AUTO
8/ 11
2
10%
Press the “OK” key.
READY TO COPY.(DOCUMENT FEEDER MODE)
2-SIDED COPY
OK
PRE-COT
EVEN NUMBER
ORIGINALS
ODD NUMBER
ORIGINALS
1
AUTO
AUTO
8/ 11
2
Enter the desired number of copies.
Press the COLOR COPY START (
5
6
INTE
1
4
2
3
TERRUPT
) key or BLACK
COPY START (
) key.
5
8
0
6
CLE
CLEAR
ALL
●
To perform color copying, press the COLOR COPY
START( ) key. To perform black/white copying, press the
BLACK COPY START ( ) key.
CA
AL
7
9
C
AUDIT
PROGRAM
C
CL
PCLEAR
●
To cancel a copy run, press the CLEAR ALL ( CA ) key. Copying
willstopandtheRADFwilloutputanyoriginalswhichhavebeen
fed. Also, the number in the copy quantity display will be reset to
0.
2-10
REDUCTION/ENLARGEMENT/ZOOM
Reduction and enlargement ratios can be selected either
automatically with the “AUTO IMAGE” key or manually with the
reduction, enlargement or “ZOOM” keys on the touch panel. The
zoom function enables precise copy ratio selection from 25% to
400% in 1% increments.
★ KEY OPERATOR A total of four extra preset copy ratios, two each
for reduction and enlargement, can be added. See page 19 of the KEY
OPERATOR’S GUIDE.
Automatic selection
Place the original on the document glass or in the
optional document feeder tray.
1
●
The original size will be detected and indicated on the touch
panel.
Press the “PAPER SELECT” key on the touch panel and
select the paper tray with the desired paper size.
READY TO COPY.
2
3
PAPER TYPE
16~28 lbs.
1
1.8/ 11
2
NOTE:
28+~35 lbs.
35+~75 lbs.
TRANSPARENCY
2.11 17
This feature will not work when original or copy paper is of non-
standard size.
3.84
AUTO
EXPOSURE
100%
COPY RATIO
P
Press the “AUTO IMAGE” key on the touch panel.
●
The best reduction or enlargement ratio for the selected paper
11
size will be automatically set and displayed on the touch panel.
17
●
If the originals and the selected copy paper are not facing the
14
AUTO IMAGE
same direction, the following message will appear to indicate
how the original should be placed.
11 17
10%
SELECT
COPY TIO
ROTATE ORIGINAL FROM TO
.
Enter the desired number of copies.
INTE
1
4
2
5
8
0
3
4
5
TERRUPT
6
CLE
CLEAR
ALL
CA
AL
Press the COLOR COPY START (
) key or BLACK
7
9
COPY START (
) key.
C
AUDIT
PROGRAM
C
●
Tocanceltheautomaticreduction/enlargementmode,pressthe
“AUTO IMAGE” key again.
PCLEAR
CL
2-11
REDUCTION/ENLARGEMENT/ZOOM
Manual selection
Place the original on the document glass or in the
optional document feeder tray.
1
2
3
4
Press the “COPY RATIO” key on the touch panel.
CUSTOM
SETTINGS
1
1.
82 11
2.
11 17
1
3.
82 14
1
AUTO
8/ 14
100%
COPY TIO
2
PAPER SELECT
MENU 1
MENU
1
2
Usethe
keytoselectmenu1ormenu2forcopy
READY TO COPY.
ratio selection.
Menu 1
OK
77%
%
100
1
121%
11 17 8/
2
14
1
1
1
8/ 14 8/ 11
8/ 14 11 17
2
2
2
ZOOM
A. Preset reduction copy ratios are: 77% and 64%.
B. Preset enlargement copy ratios are: 121% and 129%.
64%
129%
1
1
11 17 8/
2
11
1
8/
2
11 11 17
1
1
1
1
1
100%
8/ 11 5/ 8/
5/ 8/ 8/ 11
2
2
2
2
2
2
Menu 2
XY ZOOM
MENU
1
2
AUTO IMAGE
1
A. Preset reduction copy ratios are: 95%, 50%, and 25%.
B. Preset enlargement copy ratios are: 141%, 200%
and 400%.
Use the reduction, enlargement, and “ZOOM” keys on
the touch panel to set the desired copy ratio.
AUTO
AUTO
8/ 14
2
100%
COPY RATIO
EXPOSURE
PAPER SELECT
MENU 2
READY TO COPY.
OK
%
100
95
%
141%
Zoom ratios: Any ratio from 25% to 400% can be set in
1% increments.
ZOOM
50
%
25
%
200%
400%
●
Press a reduction or enlargement key to set the approximate
100%
ratio,thenpressthe
to increase the ratio.
To set the horizontal and vertical copy ratios separately, use the
XY ZOOM feature. See page 3-2.
To reset the copy ratio to 100%, press the “100%” key on the
touch panel.
The message “IMAGE IS LARGER THAN COPY PAPER.” may
appear, indicating that the selected copy ratio is too large for the
copy paper size. However, if you press the START key, a copy
will be made.
keytodecreasetheratioorthe
key
XY ZOOM
MENU
1
2
AUTO IMAGE
1
AUTO
AUTO
8/ 14
2
100%
COPY RATIO
●
●
●
EXPOSURE
PAPER SELECT
READY TO COPY.
OK
77%
%
129
1
121%
11 17 8/
2
14
1
1
1
8/ 14 8/ 11
2
8/ 14 17
2
2
ZOOM
64%
129%
1
1
11 17 8/
2
11
1
8/
2
1
1
1
100%
8/ 11 5/ 8/
2
5/
2
2
2
XY ZOOM
MENU
AUTO
1
2
A
Press the “OK” key.
AUTO
11 17
CO
5
EXPOSURE
PAPER SELECT
2-12
REDUCTION/ENLARGEMENT/ZOOM
Use the “PAPER SELECT” key to select the paper tray
with the desired paper size.
READY TO COPY.
6
7
8
●
PAPER TYPE
16~28 lbs.
If the AUTO PAPER SELECT mode is on, the appropriate copy
1
1.8/ 11
2
paper size will have been automatically selected based on the
original size and selected copy ratio.
2.11 17
28+~35 lbs.
35+~75 lbs.
TRANSPARENCY
3.84
●
If a tray of the required size is not installed, use the bypass tray
and press the “PAPER SELECT” key to select the bypass tray.
AUTO
EXPOSURE
129%
COPY RATIO
P
N
Enter the desired number of copies.
INTERRUPT
1
4
2
3
6
5
8
0
CLEAR
ALL
CA
7
9
AUDIT
PROGRAM
C
CLEAR
P
Press the COLOR COPY START (
COPY START ( ) key.
) key or BLACK
INTERRUPT
3
6
CLEAR
ALL
CA
9
PROGRAM
C
CLEAR
P
2-13
SPECIAL PAPERS (manual feed)
The bypass tray is used to copy onto transparency film and other
special purpose papers. Up to 50 sheets of standard copy paper can
be set in the bypass tray.
●
When copying onto transparency film, the maximum image loss on
the copies will be 13/32" (10 mm) along the leading and trailing
edges and 1/4" (6 mm) in total along the other edges.
Transparency film must be fed long edge into the feed slot.
●
Automatic duplex copying will not work when a non-standard sized
paper is used even if an optional duplex module (AR-DU2N) is
installed. If a duplex copying mode is selected and a non-standard
sized paper is used from the bypass tray, the corresponding one-
sided mode will be selected automatically when a START key is
pressed.
Place the original on the document glass or in the
optional document feeder tray.
1
Open the bypass tray.
2
Set the bypass tray guides to the width of the copy
paper.
3
●
Be sure to extend the tray when feeding paper larger than
8-1/2" x 11" size.
●
If the bypass tray guides are set wider than the copy paper, the
inside of the machine may become soiled, resulting in smudges
on succeeding copies.
Insert the copy paper all the way into the bypass tray.
4
●
Special purpose papers other than SHARP recommended
transparency film must be fed individually. Multiple sheets of
SHARP recommended transparency film can be loaded in the
bypass tray.
●
Up to 50 sheets of standard copy paper measuring from
5-1/2" x 8-1/2" to 12" x 18" can be loaded into the bypass tray.
●
When adding paper, first remove remaining paper, combine it
with the paper to be added and then reload as a single stack.
Press the “PAPER SELECT” key on the touch panel and
then select the desired paper type in the bypass tray
section.
INFORMATION
INTERUPT
5
1
8/ 11
2
CUSTOM
SETTINGS
PAPER TYPE
16~28 lbs.
1
.8/ 11
2
●
“16 ~ 28 lbs.” (“PLAIN PAPER”), “28+ ~ 35 lbs.” (“HEAVY
11 17
1
285 lbs.
355 lbs.
RCY
CLEAR
ALL
CA
PAPER 1”), “35+ ~ 75 lbs.” (“HEAVY PAPER 2”) or
“TRANSPARENCY” can be set.
8/ 14
2
C
CLEAR
Set the number of copies.
ER SELECT
6
7
Press the COLOR COPY START (
COPY START ( ) key.
) key or BLACK
2-14
SPECIAL PAPERS (manual feed)
Two-sided copying with bypass tray
Two-sided copies can be made manually using the bypass tray. The
procedure described below is useful for users of the copier without an
optional duplex module (AR-DU2N).
Place the first original face down on the document glass
and make a copy.
1
2
3
●
Thefirstsideofthecopycanbemadeusinganyofthepaperfeed
1 2
stations.
1 2
3 4
3 4
Remove the first original and place the second original
face down on the document glass.
●
Makesurethefirstandsecondoriginalsareorientedinthesame
way on the document glass.
●
If an optional document feeder is used, the originals must be fed
one at a time.
Turnthefirstcopyoverwithoutchangingitstop-bottom
orientation and place it into the bypass tray.
●
Be sure to feed the copies one sheet at a time.
1 2
Press the “PAPER SELECT” key and select the desired
paper type in the bypass tray section.
INFORMATION
4
5
INTERRUPT
1
8/ 11
2
CUSTOM
SETTINGS
PAPER TYPE
1
.8/ 11
2
16~28 lbs.
285 lbs.
355 lbs.
RCY
11 17
1
CLEAR
ALL
Press the COLOR COPY START (
COPY START ( ) key.
) key or BLACK
CA
8/ 14
2
C
CLEAR
ER SELECT
2-15
EXPOSURE ADJUSTMENTS
Exposure selections for this copier should be selected according to
the type of originals being copied: TEXT/PRTD. PHOTO, TEXT,
TEXT/PHOTO, PHOTO, PRINTED PHOTO or MAP. (Refer to the
samples on page 4 to see the effects on copy images in relation to
the EXPOSURE ADJUSTMENTS.) If the original image type is
TEXT/PRTD. PHOTO, TEXT or TEXT/PHOTO, the exposure can be
adjusted automatically or manually. If the original image type is
PHOTO, PRINTED PHOTO or MAP, the exposure can be adjusted
manually only. If the COPY OF COPY mode is selected only TEXT/
PRTD. PHOTO, TEXT, or PRINTED PHOTO exposure can be
selected and these can only be manually adjusted. If the COLOR
TONE ENHANCEMENT mode is selected, color copies will be more
vivid. The standard initial setting of the original image type for this
copier is TEXT/PRTD. PHOTO.
When copying a colored original in the Black/White copy mode, a
colored background with text in the background area may be
copied with the text obscured. Check with the key operator for the
setting of “Disabling of Pre-scan in B/W Copy” program (see page
30 of the Key Operator’s Guide). If pre-scan is enabled, such
obscuring may be reduced.
Automatic
This is the standard initial setting for this copier. In this mode, the
characteristics of an original being copied are “read” by the exposure
system, and exposure adjustments are made automatically.
This optimizes the contrast of the copied images.
AUTO
EXPOSURE
Original image type
TEXT/PRTD. PHOTO:
This mode provides the best balance for copying
an original which contains both text and printed
photographs.
TEXT:
Thismodeisusefulinenhancingverylowdensity
areas of an original or in suppressing unusually
high-density background areas.
TEXT/PHOTO:
This mode provides the best balance for copying
an original which contains both text and
photographs.
PRINTED PHOTO: This mode is useful for copying printed
photographs.
PHOTO:
MAP:
Thismodeprovidesthebestcopiesofphotographs
with fine details.
This mode is useful to provide the best shading
and fine details found on most maps.
COPY OF COPY: This mode provides the best result for originals
such as copied text or copied photos. If the check
box is checked, only Text/prtd. photo, Text and
Printed photo mode keys will be shown on the
touchpanelandtheexposurecanonlybeadjusted
manually.
2-16
EXPOSURE ADJUSTMENTS
Press the “EXPOSURE” key on the touch panel.
UTPUT
1
2
AUTO
AUTO
EXPOSURE
PAPE
Select “TEXT/PRTD. PHOTO”, “TEXT”, “TEXT/PHOTO”,
“PRINTED PHOTO”, “PHOTO”, or “MAP” depending
upon the original type.
COLOR TONE
OK
TEXT/
PRTD.PHOTO
ENHANCEMENT
AUTO
TEXT
TEXT/PHOTO
PHOTO
●
When making a copy from a copy made by the AR-C160,
checking the box of COPY OF COPY then choosing the proper
alternativesdependinguponthecontentoftheoriginalallowsfor
the best result.
PRINTED
MANUAL
PHOTO
COPY
MAP
1...3...5
OF COPY
●
When checking the COPY OF COPY check box, TEXT/
1
AUTO
8/ 11
2
100%
PRTD.PHOTO, TEXT and PRINTED PHOTO can be selected.
If COLOR TONE ENHANCEMENT is checked, color copies will
PAPER SELECT
COPY RATIO
EXPOSURE
●
be more vivid. COLOR TONE ENHANCEMENT and COPY OF
COPYcannotbeselectedatthesametime. TheCOLORTONE
ENHANCEMENTmodecannotbeselectedwiththesinglecolor
function. This mode, however, can be used with the RGB adjust
function.
ENHANCEMENT
PRTD.
AUTO
SIDED
TE
OPY
PRI
MANUAL
PH
If “TEXT/PRTD. PHOTO”, “TEXT” or “TEXT/PHOTO”
hasbeenselectedinstep2,select“AUTO”or“MANUAL”.
UTPUT
COP
OF
3
4
1...3...5
●
When the COPY OF COPY check box is checked, the exposure
is automatically set to “MANUAL”.
If the manual mode has been selected, use the
keys to adjust the copy density as desired.
and
COLOR TONE
ENHANCEMENT
AUTO
TEXT/
PRTD.PHOT
2-SIDED
TEXT
COPY
PRINTED
MANUAL
PHOTO
OUTPUT
COPY
1...
3...5
OF COPY
1
AUTO
8/ 1
2
PAPER SELECT
EXPOSU
2-17
JOB MEMORY
Frequently used job programs can be stored in one of nine storage
registers. This is convenient for quick job recall without losing time
manually reprogramming each aspect of the job.
●
All functions that can be set in the copy mode except the copy
quantity setting can be stored in the job memory.
If any function which has been stored in a job program is modified
●
byakeyoperatorprogram, thekeyoperatorsettingswillsupercede
the previous setting.
★ KEY OPERATOR Job memory replacement/deletion can be
prohibited. See page 28 of the KEY OPERATOR’S GUIDE.
Storing a job program
Press the PROGRAM key.
1
2
3
●
The JOB PROGRAMS screen will appear on the touch panel.
8 9
IT
PROGRAM
C
CLEAR
0
P
Press the “STORE/DELETE” key on the touch panel.
●
To cancel the job memory mode, press the “EXIT” key or the
CLEAR ALL ( CA ) key.
RECALL
STOREELETE
Select a program number from 1 to 9 on the touch panel.
EXIT
JOB PROGRAMS
PRESS PROGRAM NUMBER.
●
The numbers which are highlighted are job registers which
already contain job programs.
●
If a program number containing a registered job program is
selected, a message will appear to confirm the selection. To
replace a stored job program with a new program, press the
“STORE” key and proceed to the next step.
To cancel replacement, press the “CANCEL” key.
RECALL
STOELETE
Make all copier selections to be stored.
MAKE COPIER SELECTIONS AND PRESS
[OK].
OK
4
5
NOTE:
When you store color balance settings, make settings before
pressing the PROGRAM key in step 1 because sample copies
cannot be made after pressing the PROGRAM key.
1
1.
82 11
2.
11 17
1
3.
82 14
1
AUTO
AUTO
8/ 11
2
Press the “OK” key to complete the storage.
EXPOSURE
PAPER SELECT
2-18
JOB MEMORY
Deleting a stored job program
Follow steps 1 and 2 in “Storing a job program” on the
previous page. (1. Press the PROGRAM key. 2. Press
the “STORE/DELETE” key.)
EXIT
JOB PROGRAMS
1
2
PRESS PROGRAM NUMBER.
Select the storage register number of the program to be
deleted.
●
Be sure to select a number which contains a stored program. If
not, “Storing a job program” operation will start.
RECALL
T
JOB PROGRAMS
Press the “DELETE” key or the “CANCEL” key.
PRESS PROGRAM NUMBER.
3
●
Ifthe“DELETE”keyispressed, theprogramwillbedeletedfrom
JOB PROGRAM HAS BEEN ALREADY STORED.
STORE ANOTHER PROGRAM?
OR DELETE?
memory.
●
Press the “CANCEL” key to keep the program.
CANCEL
DELETE
STORE
RECALL
STORE/DELETE
Press the “EXIT” key to exit the job memory mode.
EXIT
JOB PROGRAMS
4
PRESS PROGRAM NUMBER.
RECALL
STO
Recalling a job program
8 9
PROGRAM
IT
C
CLEAR
Press the PROGRAM key.
1
●
The JOB PROGRAMS screen will appear on the touch panel.
0
P
●
Thenumberswhicharehighlightedareprogramnumberswhich
contain stored programs.
Select a stored program from 1 to 9 on the touch panel.
EXIT
JOB PROGRAMS
●
All selections stored in the program will appear on the touch
2
PRESS PROGRAM NUMBER.
panel.
●
Therecalledsettingsmaybemodifiedforaparticularjobrun,but
anychangesmadewillnotbestoredinthejobmemory. Tostore
the new settings, follow the “Storing a job program” procedure.
RECALL
STORE/DELETE
2-19
INTERRUPTING A COPY RUN
INTERRUPT can be used to temporarily stop a long copy run so that
another job can be run.
●
INTERRUPT will not function during duplex copying (when an
optional duplex module (AR-DU2N) is installed).
Duplex copying, sort, group, staple sort and offset cannot be
●
selectedduringinterruptcopying.Alsojobprogramrecallcannotbe
selected.
Press the INTERRUPT key.
●
Whentheoptionaldocumentfeederisbeingused,thecopierwill
stop after copying any originals which have been fed into the
document feeder. The INTERRUPT indicator will blink until the
1
INTERRUPT
3
copier stops.
When the copier stops, it will return to its initial settings and the
INTERRUPT indicator will light steadily. At this time, the copier
is ready for interrupt copying.
6
CLR
A
CA
●
If the copier has been programmed in the auditing mode, the
account number entry message will appear. Enter your account
number using the 10-key pad. The number of copies of the
interrupt copying will be accumulated against this account
number.
When the copier stops, remove the original(s) and set
the original(s) for interrupt copying on the document
glass or in the optional document feeder tray.
2
Select the desired available copier functions.
INTERRUPT
CLEAR
3
4
3
6
Press the COLOR COPY START (
COPY START ( ) key.
) key or BLACK
CA
ALL
9
PROGRAM
C
CLEAR
P
When the interrupt copy run is complete, press the
INTERRUPT key again to cancel the mode and remove
the original(s) used for interrupt copying.
5
6
INTERRUPT
CLR
3
6
●
The copier will reset itself to the functions which were in use
before the INTERRUPT key was first pressed.
Replace the original(s) for the interrupted job and press
the COLOR COPY START (
) key or BLACK COPY
CA
START ( ) key to resume copying.
A
2-20
CHAPTER 3
SPECIAL FUNCTIONS
This chapter describes the special copying functions including various
image editing functions which have been made possible by digital image
processing technology.
Page
●
XY ZOOM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
●
MARGIN SHIFT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
●
ERASE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
●
DUAL PAGE COPYING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
●
CENTERING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
●
TRANSPARENCY FILMWITH INSERT SHEETS . . . . . . . . . . . 3-12
●
COVERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
●
COLOR ADJUSTMENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16
RGB adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16
Sharpness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18
Suppress background. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20
Color balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22
Brightness/intensity/contrast. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24
●
IMAGE EDITING FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . 3-26
Single color. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26
Neg. /pos. reverse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-28
Mirror image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-30
Photo repeat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-32
11 x 17 full-bleed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-34
Multi-page enlargement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-36
Extra size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-38
3-1
XY ZOOM
The XY ZOOM feature allows the horizontal and vertical copy ratios to
be changed independently. If this feature is selected, the copy ratios
can be set from 25% to 400%.
Original
Copy
Place the original on the document glass or in the
optional document feeder tray.
1
Press the “COPY RATIO” key on the touch panel.
2
3
1
8/ 11
100%
2
ELECT
COPY ATIO
Press the “XY ZOOM” key.
●
The following screen will appear.
/
/
READY TO COPY.
ZOOM
COPY
64
%
OK
1
X
Y
100
100
%
%
11 17 8/ 11
2
77%
64%
50%
129
200
400
%
%
%
1
1
1
100%
8/ 11 5/ 8/
2
2
2
OUTPUT
ZOOM
XY ZOOM
MENU
100%
O
AUTO
XY ZOOM
AUTO
CANCEL
EXURE
PAPER S
1
AUTO
8/ 11
2
100%
COPY RATIO
EXPOSURE
PAPER SELECT
READY TO COPY.
Use the reduction, enlargement , and ZOOM (
,
)
OK
keys to change the copy ratio in the horizontal (X)
direction.
4
X
Y
100
100
%
%
77
64
50
%
129
200
400
%
%
%
●
%
Press a reduction key or an enlargement key to set the
ZOOM
approximate ratio, then press the
or key to increase the ratio.
key to decrease the ratio
100%
%
CANCEL
Y ZOOM
UTO
OSURE
1
AUTO
8/ 11
2
100%
COPY RATIO
PAPER SELECT
3-2
XY ZOOM
Press the
key.
TO COPY.
5
6
●
The copy ratio in the vertical (Y) direction will be highlighted.
X
50
100
ZOOM
%
%
READY TO COPY.
Use the reduction, enlargement, and ZOOM (
keystochangethecopyratiointhevertical(Y)direction.
,
)
X
Y
50
100
OK
77%
●
●
To change the copy ratio in the horizontal direction again, press
X
the
key.
ZOOM
1
%
The message “IMAGE IS LARGER THAN COPY PAPER.” may
appear, indicating that the selected copy ratio is too large for the
copypapersize. However, ifyoupressaSTARTkey, acopywill
be made.
100%
0
%
CANCEL
OM
1
AUTO
8/
2
PAPER SELEC
Press the “OK” key.
7
8
READY TO COPY.
Press the “PAPER SELECT” key and select the paper
tray with the desired paper size.
PAPER TYPE
16~28 lbs.
●
1
If the AUTO PAPER SELECT mode is on, the appropriate copy
1.8/ 11
2
paper size will have been automatically selected based on the
original size and selected copy ratios.
28+~35 lbs.
35+~75 lbs.
TRANSPARENCY
2.11 17
3.84
AUTO
EXPOSURE
X-50% Y-77%
P
COPY RATIO
Enter the desired number of copies.
INTE
1
4
2
5
8
0
3
TERRUPT
9
6
CLE
CLEAR
ALL
Press the COLOR COPY START (
) key or BLACK
CA
AL
COPY START (
) key.
10
7
9
●
To cancel this function, press the “CANCEL” key or the “XY
ZOOM” key again as in step 3.
C
AUDIT
PROGRAM
C
PCLEAR
CL
3-3
MARGIN SHIFT
The MARGIN SHIFT feature, in its initial setting, shifts the text or image to
therightonone-sidedcopiesandonthefrontsideoftwo-sidedcopies. The
text or image is shifted to the left on the reverse side of two-sided copies.
Shift direction can be changed to left or right as described in step 4 below.
Original
Copy
●
The standard shift amount is 1/2", but can be changed from 0" to 1" in
1/8" increments.
★ KEY OPERATOR
The initial shift setting can be changed from 0" to 1"
in 1/8" increments. See page 20 of the KEY OPERATOR’S GUIDE.
Expanded margin
NOTE:
(Initial setting:
The front side and reverse side are referred to as “SIDE 1” and “SIDE 2”
respectively on the touch panel.
copy image shifted to the right)
Place an original on the document glass or in the
optional document feeder tray.
1
Margin is expanded
here.
Margin is expanded
here.
Press the SPECIAL MODES key.
2
●
The SPECIAL MODES screen will appear.
READY TO COPY.
READY TO
SPECIAL MODES
OK
SPECIAL
MODES
DUAL PAGE
COPY
MARGIN SHIFT
ERASE
CENTERING
COVERS
TRANSPARENCY INSERTS
COLOR
IMAGE EDIT
2-SED
CY
ADJUSTMENTS
1
AUTO
AUTO
8/ 11
100%
COPY RATIO
2
EXPOSURE
PAPER SELECT
3-4
MARGIN SHIFT
Press the “MARGIN SHIFT” key on the touch panel.
READY TO COPY.
SPECIAL MODES
3
●
The setting screen for MARGIN SHIFT will appear.
OK
DUAL PAGE
COPY
ERASE
MARGIN SHIFT
CRING
CO
READY TO COPY.
OK
TRANSPARENCY INSERTS
CANCEL
COLOR
OK
MARGIN SHIFT
RIGHT
IMAGE EDIT
ADJUSTMENTS
1
SIDE 1
SIDE 2
AUTO
8/ 11
2
100%
COPY RATIO
LEFT
PAPER SELECT
(0~1)
inch
(0~1)
1/2
1/2
inch
MARGIN SHIFT
CANCEL
SIDE 1
2-SIDED
COPY
●
If an optional duplex module (AR-DU2N) is not installed, the
margin shift setting for the reverse side will not be displayed.
RIGHT
LEFT
OUTPUT
(0~1)
1/2
inch
Select the shift direction.
4
5
●
Select“RIGHT”or “LEFT”onthetouchpanel. Theselectedshift
direction will be highlighted.
DED
PY
Select the desired shift amounts using the
keys.
and
SIDE 1
RIGHT
LEFT
PUT
(0~1)
1/2
inch
Press the upper “OK” key on the touch panel.
INFORMAT
INTT
6
7
OK
CUSTO
SETTING
CLR
CA
L
Make all other desired copier selections and press the
COLOR COPY START ( ) key or BLACK COPY
SI
C
CLEAR
START (
) key.
●
To cancel the MARGIN SHIFT function, select the MARGIN
SHIFT function again and press the “CANCEL” key.
3-5
ERASE
(Original)
(Copy)
Erasefunctioncanbeusedtoeliminateshadowlinesaroundtheedgesand
the center part of copies as shown in the illustrations, which are caused
when such originals as thick paper, books or bound documents are used.
3 patterns of erase function, EDGE ERASE, CENTER ERASE and
EDGE+CENTER ERASE can be selected.
Edge erase
A
A
●
The standard erase width is 1/2", but can be changed from 0" to 1" in
1/8" increments.
★ KEY OPERATOR The initial setting of the width for edge erase and center
Center erase
erase can be changed. See page 20 of the KEY OPERATOR’S GUIDE.
A B
A B
A B
Edge + center erase
A B
Place an original on the document glass or in the
optional document feeder tray.
1
Press the SPECIAL MODES key.
2
●
The SPECIAL MODES screen will appear.
READY TO
SPECIAL
MODES
2-SED
CY
Press the “ERASE” key on the touch panel.
3
●
The setting screen for ERASE will appear.
READY TO COPY.
READY TO COPY.
SPECIAL MODES
OK
OK
DUAL PAGE
COPY
MARGIN SHIFT
CENTERING
COVERS
ERASE
CANCEL
OK
ERASE
(0~1)
ANSPARENCY INSERTS
1/2
inch
EDGE ERASE
CO
IMAGE EDIT
ADENTS
CENTER ERASE
AUTO
O
100%
COPY RATIO
EDGE+CENTER
ERASE
EXPOSURE
3-6
ERASE
Select the desired erase mode.
OK
OK
4
5
6
7
●
Select“EDGEERASE”,“CENTERERASE”or“EDGE+CENTER
ERASE” on the touch panel. The selected erase mode will be
highlighted.
CANCEL
ERASE
EDGE ERASE
CENTER ERASE
EDGE+CENTER
ERASE
Adjust the amount of edge erase and/or center erase if
needed.
OK
OK
CANCEL
ERASE
●
Theamountcanbeadjustedbetween0"and1"in1/8"increments.
(0~1)
1/2
inch
EDGE ERASE
CENTER ERASE
EDGE+CENTER
ERASE
Press the upper “OK” key on the touch panel.
INFORMATION
OK
O
CUSTOM
SETTINGS
CANCEL
)
Make all other desired copier selections and press the
INTERRUPT
COLOR COPY START (
) key or BLACK COPY
3
6
START (
) key.
●
TocanceltheERASEfunction,selecttheERASEfunctionagain
and press the “CANCEL” key.
CLEAR
ALL
CA
9
PROGRAM
C
CLEAR
P
3-7
DUAL PAGE COPYING
The DUAL PAGE COPY feature produces separate copies of two
documents placed side by side on the document glass. It is especially
useful when copying books and other bound documents.
Original
Copies
This feature can be used in the one-sided to two-sided copying mode.
Place the originals on the document glass with the
centerofthetwopagesalignedwiththepapersizeindex
1
81/2. Close the document cover.
●
Set the page to be copied first on the left part of the document
glass.
81/2
Paper size index
Press the SPECIAL MODES key.
2
3
●
The SPECIAL MODES screen will appear.
READY TO
SPECIAL
MODES
2-SED
CY
Press the “DUAL PAGE COPY” key on the touch panel.
READY TO COPY.
SPECIAL MODES
●
The “DUAL PAGE COPY” key will be highlighted.
OK
●
DUAL PAGE
COPY
8-1/2" x 11" sized copy paper will be automatically selected.
MARGIN SHIFT
CENTERING
COVERS
ERASE
If 8-1/2" x 11" copy paper is not loaded, copying can be done on
another size.
TRANSPARENCY INSE
COLOR
●
IMAGT
To leave a binding margin on the copy, select the MARGIN
SHIFT function. See page 3-4.
ADJUSTMENTS
1
AUTO
AUTO
8/ 11
2
1
EXPOSURE
PAPER SELECT
●
●
To erase shadows caused by document binding, use the EDGE
ERASE feature. See page 3-6.
The CENTER ERASE feature is not available with the DUAL
PAGE COPY feature.
3-8
DUAL PAGE COPYING
Press the “OK” key.
INFORMATION
4
5
6
7
OK
CUSTOM
SETTINGS
DUAGE
COP
SPARENCY INSER
Ensure that the desired tray is selected.
TO COPY.
1
1.
82 11
2.
11 17
1
3.
82 14
1
2
N
Enter the desired number of copies.
INTERRUPT
1
2
5
8
0
3
6
4
CLEAR
ALL
CA
7
9
AUDIT
PROGRAM
C
CLEAR
P
Press the COLOR COPY START (
) key or BLACK
INTERRUPT
CLEAR
COPY START (
) key.
3
6
●
To cancel the DUAL PAGE COPY function, press the “DUAL
PAGE COPY” key again on the SPECIAL MODES screen.
CA
ALL
9
PROGRAM
C
CLEAR
P
3-9
CENTERING
When the original and copy paper are of different sizes, CENTERING
is used to shift the image as a whole to the center of the copy paper.
The image will shift only in the left to right direction, not in the top to
bottom direction.
Original
Copy
●
Thisfunctioncanbeusedtoreducealargersizedoriginal imageand
center it on a copy of smaller paper size, as well as center a smaller
original onto a larger sized copy.
This function will not work when non-standard size originals or copy
●
paperareused.Thisfunctioncannotbeselectedwhenenlargement
copying has been selected.
Place the originals on the document glass or in the
optional document feeder tray.
1
Press the “PAPER SELECT” key on the touch panel and
select the desired paper size.
READY TO COPY.
2
3
PAPER TYPE
16~28 lbs.
1
1.8/ 11
2
28+~35 lbs.
35+~75 lbs.
TRANSPARENCY
2.11 17
3.84
AUTO
EXPOSURE
100%
COPY RATIO
P
Press the SPECIAL MODES key.
●
The SPECIAL MODES screen will appear.
READY TO
SPECIAL
MODES
2-SED
CY
3-10
CENTERING
Press the “CENTERING” key on the touch panel.
READY TO COPY.
SPECIAL MODES
4
5
6
7
●
OK
The “CENTERING” key will be highlighted.
DUAL PAGE
COPY
MARGIN SHIFT
CENTERING
COV
ERASE
TRANSPARENCY INSERTS
COLOR
IMAGE EDIT
ADJUSTMENTS
1
A
AUTO
8/ 11
2
100%
COPY RATIO
EXP
PAPER SELECT
Press the “OK” key.
OK
DUAAGE
COP
ERASE
TRANSPARENCY INSE
N
Make all other desired copier selections and enter the
desired number of copies.
INTERRUPT
1
4
2
5
8
0
3
6
CLEAR
CA
ALL
7
9
AUDIT
PROGRAM
C
CLEAR
P
Press the COLOR COPY START (
) key or BLACK
COPY START (
) key.
INTERRUPT
CLEAR
3
6
●
To cancel the CENTERING function, press the “CENTERING”
key again on the SPECIAL MODES screen.
CA
ALL
9
PROGRAM
C
CLEAR
P
3-11
TRANSPARENCY FILM WITH INSERT SHEETS
When copying onto transparency film, blank insert sheets can be
placed following each transparent sheet.
Originals (1-sided)
4
3
●
2
1
Insert sheets cannot be copied on in any mode.
4
3
●
Thismodecanbeselectedonlyinthe1-sidedto1-sidedand2-sided
to 1-sided modes.
2
1
●
A multiple number of copies cannot be selected in this mode.
Originals (2-sided)
●
Transparency film must be fed from the bypass tray.
3
1
●
Insert sheets must be the same size as the transparency film.
Insert sheets
●
For best results, use SHARP recommended transparency film.
Place the originals on the document glass or in the
optional document feeder tray.
1
Press the SPECIAL MODES key.
2
3
●
The SPECIAL MODES screen will appear.
READY TO
SPECIAL
MODES
2-SED
CY
Pressthe“TRANSPARENCYINSERTS”keyonthetouch
panel.
READY TO COPY.
SPECIAL MODES
OK
●
The “TRANSPARENCY INSERTS” key will be highlighted.
DUAL PAGE
COPY
MARGIN SHIFT
CENTERING
COVERS
ERASE
TRANSPARENCY INSERTS
COLOR
IMAGE EDIT
ADJUSTMENTS
1
AUTO
AUTO
8/ 11
2
100%
OPY RATIO
EXPOSURE
PAPER SELECT
3-12
TRANSPARENCY FILM WITH INSERT SHEETS
Press the “OK” key.
INFOR
4
OK
CUS
SET
DUAAGE
COP
SE
RANSPARENCY INSE
Load transparency film into the bypass tray.
●
Set the long edge of the film to be fed into the machine.
5
6
7
Ensure that the tray selected for the insert sheets
contains paper of the same size and orientation of the
transparency films.
1
ORIGINAL
82 11
CUSTOM
SETTINGS
1
82 11
TRANSPARENCY
1
1.
82 11
2.
11 17
1
3.
82 14
1
AUTO
8/ 11
100%
COPY RATIO
2
PAPER SELECT
Make all other selections and press the COLOR COPY
START (
INTERRUPT
CLEAR
) key or BLACK COPY START (
) key.
3
6
●
When copying is completed, remove remaining transparency
film.
CA
●
ALL
To cancel the TRANSPARENCY INSERTS function, press the
“TRANSPARENCY INSERTS” key again on the SPECIAL
MODES screen.
9
PROGRAM
C
CLEAR
P
3-13
COVERS
The COVERS mode is used to place covers on the front, back, or both
the front and back of multipage documents.
●
To use the COVERS mode, an optional RADF must be installed.
●
Front cover sheets can be copied on, but only on the front side even
in the 1-sided to 2-sided and 2-sided to 2-sided copy modes.
The back side of the original designated as the cover will not be
copied.
Covers
●
Backcoversheetscannotbecopiedon, eitheronthefrontsideoron
the back side.
●
Coversheetsmustbefedfromthebypasstrayandmustbethesame
size as the copy paper being used to copy the document.
When the COVERS mode is selected, the stream feeding mode of
●
the RADF will always be off.
Place the originals in the optional document feeder tray.
1
Press the 2-SIDED COPY key and select the desired
duplex mode if needed. Press the “OK” key to close the
duplex selection window.
2
2-SIDED
COPY
●
To copy in the 1-sided to 2-sided or 2-sided to 2-sided copy
mode, anoptionalduplexmodule(AR-DU2N)mustbeinstalled.
OUTPUT
Press the SPECIAL MODES key.
3
4
●
READY TO
The SPECIAL MODES screen will appear.
SPECIAL
MODES
2-SED
CY
Press the “COVERS” key on the touch panel.
●
The setting screen for COVERS will appear.
LOAD COVER STOCK INTO BYPASS-TRAY.
READY TO COPY.
SPECIAL MODES
OK
OK
DUAL PAGE
COPY
MARGIN SHIFT
CENTERING
COS
ERASE
CANCEL
PRINT ON FRONT COVER?
OK
COVERS
TRANSPARENCY INSERTS
FRONT
BACK
YES
NO
COLOR
IMAGE EDIT
ADJUSTMENTS
1
O
AUTO
8/ 11
2
100%
COPY RATIO
FRONT+BACK
EURE
PAPER SELECT
3-14
COVERS
Select cover placement.
O
O
5
6
7
8
●
Select “FRONT”, “BACK” or “FRONT+BACK” on the touch
panel.
CANCEL
PRINT ON FRONT
COVERS
FRONT
YES
NO
BACK
FRONT+BACK
Indicate whether the front cover sheets are copied on or
not.
OK
OK
CANCEL
●
Select“YES”or“NO”onthetouchpanel.If“YES”isselected,the
PRINT ON FRONT COVER?
first page of the document will be copied onto the front cover
sheet.
T
YES
NO
●
If “BACK” has been selected in step 5, this selection is not
needed.
T+BACK
Press the upper “OK” key.
OK
CUS
SETT
NCEL
OK
T ON FRON?
Load the cover stock into the bypass tray, making sure
that the cover stock is the same size as the copy paper.
●
The message “SELECT PAPER TYPE FOR BYPASS-TRAY.”
will appear if “16 ~ 28 lbs.” (“PLAIN PAPER”), “28+ ~ 35 lbs.”
(“HEAVYPAPER1”)or“35+~75lbs.”(“HEAVYPAPER2”)has
not been selected.
Select the paper type for the bypass tray.
9
●
Transparency film cannot be selected as cover stock.
INTE
●
The START key indicators will light up.
1
4
2
5
8
0
3
TERRUPT
6
9
CLE
CLEAR
ALL
CA
Enter the desired number of copies and press the
COLOR COPY START (
START (
AL
) key or BLACK COPY
7
10
C
AUDIT
PROGRAM
) key.
C
CL
PCLEAR
●
To cancel the COVERS function, select the COVERS function
again and press the “CANCEL” key.
3-15
COLOR ADJUSTMENTS
The color adjustments include the following items.
●
RGB adjust: Strengthens or weakens one of three primary colors, red (R), green (G), or blue (B).
●
Sharpness: Sharpens or softens image outlines.
●
Suppress background: Suppresses copying of lighter background areas.
●
Color balance: Adjusts the color, tone, and density of color copies.
●
Brightness/intensity/contrast: These adjust the level of brightness, intensity or contrast of images.
RGB ADJUST
This function can be used to strengthen or weaken the three primary
colors, red (R), green (G), or blue (B).
Only one primary color can be adjusted at a time.
If a second primary color is adjusted, the first adjustment will be
cancelled.
(Refer to the samples on page 5 to see the effect on copy images in
relation to the RGB ADJUST.)
Place the original on the document glass or in the
optional document feeder tray.
1
Press the SPECIAL MODES key.
2
●
The SPECIAL MODES screen will appear.
READY TO
SPECIAL
MODES
2-SED
CY
Press the “COLOR ADJUSTMENTS” key on the touch
panel.
3
●
The COLOR ADJUSTMENTS menu will appear.
READY TO COPY.
READY TO COPY.
SPECIAL MODES
OK
OK
OK
SPECIAL MODES
DUAL PAGE
COPY
MARGIN SHIFT
CENTERING
COVERS
ERASE
COLOR ADJUSTMENTS
SUPPRESS
RGB ADJUST
SHARPNESS
INTENSITY
TRANSPARENCY INSERTS
BACKGROUND
COLOR
COLOR
IMAGE EDIT
BALANCE
ADJUENTS
1
AUTO
AUTO
8/ 11
2
100%
COPY RATIO
BRIGHTNESS
CONTRAST
EXPOSURE
PAPELECT
3-16
COLOR ADJUSTMENTS
Press the “RGB ADJUST” key on the touch panel.
READY TO COPY.
4
●
The setting screen for RGB ADJUSTMENTS will appear.
OK
OK
SPECIAL MODES
COLOR ADJUSTMENTS
READY TO COPY.
SUPPRESS
RGB ADJUST
SHARPNESS
INTENSITY
OK
OK
BACKGROUND
SPECIAL MODES
RGB ADJUST
CO
CANCEL
BAE
ONLY ONE COLOR CAN BE ADJUSTED.
BRIESS
CONTRAST
R(RED)
G(GREEN)
B(BLUE)
READY TO COPY.
-2 · -1 · · 0 · · 1 · 2
OK
OK
SPECIAL MODES
RGB ADJUST
ONLY ONE COLOR CAN BE ADJUSTED.
CANCEL
Select a color to be adjusted.
5
6
●
Select a color from R (RED), G (GREEN), and B (BLUE).
R(RED)
G(GREEN)
B(BLUE)
-2 · -1 · · · 1 · 2
Press the “+” to strengthen the selected color or press
the “-” key to weaken the color.
RGB ADJUST
ONLY ONE COLOR CAN BE ADJUSTED.
CANCEL
OK
●
The level can be adjusted from -2 to 2 in eleven steps.
R(RED) G(GREEN)
B(BLUE)
-2 · -1 · · · · 1 · 2
Press the upper “OK” key.
READY TO COPY.
RGB ADJUST
7
OK
K
CANCEL
ONLY ONE COLOR CAN BE ADJUSTED.
R(RED) G(GREEN)
B(B
-2 · -1 · · 0 · · 1 ·
Make all other desired copier selections and enter the
desired number of copies.
INTE
8
9
1
4
2
5
8
0
3
TERRUPT
Press the COLOR COPY START (
) key.
6
9
CLE
CLEAR
ALL
CA
AL
●
TheBLACKCOPYSTART(
)keycanbepressedforcopying.
7
However, the RGB ADJUST setting will be ignored.
C
AUDIT
PROGRAM
C
CL
●
To cancel the RGB ADJUST function, select the RGB ADJUST
function again and press the “CANCEL” key.
PCLEAR
3-17
COLOR ADJUSTMENTS
SHARPNESS
This function is used to sharpen or soften image outlines.
(Refer to the samples on page 6 to see the effect on copy images in
relation to the SHARPNESS.)
Place the original on the document glass or in the
optional document feeder tray.
1
Press the SPECIAL MODES key.
2
●
The SPECIAL MODES screen will appear.
READY TO
SPECIAL
MODES
2-SED
CY
Press the “COLOR ADJUSTMENTS” key on the touch
panel.
READY TO COPY.
3
4
OK
SPECIAL MODES
MARGIN SHIFT
●
The COLOR ADJUSTMENTS menu will appear.
DUAL PAGE
COPY
ERASE
CENTERING
COVERS
TRANSPARENCY INSERTS
COLOR
IMAGE EDIT
ADJUENTS
1
AUTO
AUTO
8/ 11
2
100%
COPY RATIO
Press the “SHARPNESS” key on the touch panel.
EXPOSURE
PAPELECT
●
The setting screen for SHARPNESS will appear.
READY TO COPY.
READY TO COPY.
OK
OK
OK
SPECIAL MODES
COLOR ADJUSTMENTS
SHARPNESS
CANCEL
OK
CEN
SUPPRESS
RGB ADJUST
SHARPNESS
INITY
BACKGROUND
COLOR
SOFT
SHARP
BALANCE
BRIGHTNESS
CONTRAST
3-18
COLOR ADJUSTMENTS
Press the “SOFT” key to soften image outlines or press
the “SHARP” key to sharpen them.
READY TO COPY
SHARPNESS
5
6
7
8
OK
OK
CANCEL
SOFT
SHARP
Press the upper “OK” key.
READY TO COPY
SHARPNESS
OK
CANCEL
SOFT
SHARP
N
Make all other desired copier selections and enter the
desired number of copies.
INTERRUPT
1
4
2
5
8
0
3
6
CLEAR
ALL
CA
7
9
AUDIT
PROGRAM
C
CLEAR
P
Press the COLOR COPY START (
) key.
INTERRUPT
CLEAR
●
The BLACK COPY START (
) key can be pressed for
3
6
copying. However, the SHARPNESS setting will be ignored.
●
To cancel the SHARPNESS function, select the SHARPNESS
function again and press the “CANCEL” key.
CA
ALL
9
PROGRAM
C
CLEAR
P
3-19
COLOR ADJUSTMENTS
SUPPRESS BACKGROUND
This copier can suppress unwanted background areas on the original
images when copying. This function is used to adjust the density
level of background images to be erased.
(Refer to the samples on page 6 to see the effect on copy images in
relation to the SUPPRESS BACKGROUND.)
Place the original on the document glass or in the
optional document feeder tray.
1
Press the SPECIAL MODES key.
2
●
The SPECIAL MODES screen will appear.
READY TO
SPECIAL
MODES
2-SED
CY
Press the “COLOR ADJUSTMENTS” key on the touch
panel.
READY TO COPY.
SPECIAL MODES
3
4
OK
●
The COLOR ADJUSTMENTS menu will appear.
DUAL PAGE
COPY
MARGIN SHIFT
CENTERING
COVERS
ERASE
TRANSPARENCY INSERTS
COLOR
IMAGE EDIT
ADJUENTS
1
AUTO
AUTO
8/ 11
2
100%
COPY RATIO
Pressthe“SUPPRESSBACKGROUND”keyonthetouch
panel.
EXPOSURE
PAPELECT
●
ThesettingscreenforSUPPRESSBACKGROUNDwillappear.
READY TO COPY.
OK
OK
READY TO COPY.
SPECIAL MODES
COLOR ADJUSTMENTS
OK
CEN
SUPPRESS
RGB ADJUST
SHARPNESS
INTENSITY
OK
SUPPRESS BACKGROUND
CANCEL
BACKOUND
LIGHT AREAS OF THE ORIGINAL MAY BE SUPPRESSED
COLOR
AS BACKGROUND.
BALANCE
BRIGHTNESS
CAST
3-20
COLOR ADJUSTMENTS
Usethe“-”and“+”keystoselectthedesiredbackground
suppression level.
OK
OK
5
6
7
8
SUPPRESS BACKGROUND
CANCEL
●
LIGHT AREAS OF THE ORIGINAL MAY BE SUPPRESSED
If level 1 is selected, darker background areas will be erased.
AS BACKGROUND.
The level can be adjusted in three steps. The default setting is
level 3.
Press the upper “OK” key.
READY TO COPY.
OK
SUPPRESS BACKGROUND
CANCEL
LIGHT AREAS OF THE ORIGINAL MAY BE SUPPR
AS BACKGROUND.
N
Make all other desired copier selections and enter the
desired number of copies.
INTERRUPT
1
4
2
5
8
0
3
6
CLEAR
ALL
CA
7
9
AUDIT
PROGRAM
C
CLEAR
P
Press the COLOR COPY START (
) key.
INTERRUPT
CLEAR
●
The BLACK COPY START (
) key can be pressed for
3
6
9
copying. However, theSUPPRESSBACKGROUNDsettingwill
be ignored.
CA
ALL
●
To cancel the SUPPRESS BACKGROUND function, select the
SUPPRESS BACKGROUND function again and press the
“CANCEL” key.
PROGRAM
C
CLEAR
P
3-21
COLOR ADJUSTMENTS
COLOR BALANCE
This function is used to adjust the color, tone, and density of color
copies.
The Color Balance setting allows you to adjust the densities of four
colors: cyan, magenta, yellow, and black. The density range is
divided into eight levels for each color, from 1 (lowest density areas)
to 8 (highest density areas). The density can be adjusted one level at
a time or eight levels at once. (Refer to the samples on page 7 to see
the effect on copy images in relation to the COLOR BALANCE.)
Place the original on the document glass or in the
optional document feeder tray.
1
Press the SPECIAL MODES key.
2
3
4
●
The SPECIAL MODES screen will appear.
READY TO
SPECIAL
MODES
2-SED
CY
Press the “COLOR ADJUSTMENTS” key on the touch
panel.
READY TO COPY.
OK
SPECIAL MODES
MARGIN SHIFT
●
The COLOR ADJUSTMENTS menu will appear.
DUAL PAGE
COPY
ERASE
CENTERING
COVERS
TRANSPARENCY INSERTS
COLOR
IMAGE EDIT
ADJUENTS
1
AUTO
AUTO
8/ 11
2
100%
COPY RATIO
EXPOSURE
PAPELECT
Press the “COLOR BALANCE” key on the touch panel.
READY TO COPY.
OK
OK
SPECIAL MODES
COLOR ADJUSTMENTS
SUPPRESS
RGB ADJUST
SHARPNESS
INTENSITY
BACKGROUND
CENTERING
COLOR
BALANCE
BRIESS
CONTRAST
3-22
COLOR ADJUSTMENTS
●
The setting screen for COLOR BALANCE will appear.
READY TO COPY.
OK
OK
SPECIAL MODES
COLOR BALANCE
CANCEL
C
M
Y
Bk
Use the keys indicated in the illustration above to adjust
the color balance settings.
READY TO COPY
COLOR BALANCE
5
OK
OK
C
Use these keys to select the color to be adjusted (
= cyan,
CANCEL
M
Y
Bk
= magenta,
= yellow,
= black).
If only the area around the letter inside a key is highlighted, the
settings have been changed from the factory default settings.
C
M
Use these keys to adjust the densities of each of the eight
density levels.
When one of the keys is pressed, the corresponding indicator
line will move up or down one step. Press the
increase the density of the corresponding level, or the
to decrease the density.
key to
key
Use these keys to change the densities of all eight levels at
once.
When either key is pressed, the indicator lines of all eight levels
will move up or down one step.
Press the
key to increase the density, or the
key to
decrease the density.
Use this key to return the densities of all eight levels to the
initial settings.
The initial color balance settings are the values set with key
operator program “Initial Color Balance Setting”.For this reason,
the initial settings may not necessarily be 0 (the middle indicator
position) for all levels.The initial setting of each level is shown
by a gray indicator. See page 22 of the KEY OPERATOR'S
GUIDE.
N
INTERRUPT
1
4
2
5
8
0
3
6
CLEAR
ALL
CA
7
9
Make all other desired copier selections and enter the
desired number of copies.
AUDIT
PROGRAM
C
CLEAR
6
7
P
Press the COLOR COPY START (
) key.
INTERRUPT
CLEAR
●
The BLACK COPY START (
) key can be pressed for
3
6
copying.However,theCOLORBALANCEsettingswillbeignored.
●
Youcanalsostorecolorbalancesettingsforrepeateduseinthe
future. (Refer to “Storing a Job Program” on page 2-18). In this
case, complete the color balance setting before pressing the
PROGRAM key bacause color copy samples cannot be made
after the PROGRAM key is pressed.
CA
ALL
9
PROGRAM
C
CLEAR
P
3-23
COLOR ADJUSTMENTS
BRIGHTNESS /INTENSITY /CONTRAST
This copier allows the level of brightness, intensity or contrast of
images to be adjusted. If brightness is selected, color tone can be
darkened or lightened. If intensity is selected, color saturation can be
made to be more vivid or more dull. If contrast is selected, the
contrast between image areas can be made to be higher or lower.
(Refer to the samples on page 8 to see the effect on copy images in
relation to the BRIGHTNESS /INTENSITY /CONTRAST
adjustments.)
Place the original on the document glass or in the
optional document feeder tray.
1
Press the SPECIAL MODES key.
2
●
The SPECIAL MODES screen will appear.
READY TO
SPECIAL
MODES
2-SED
CY
Press the “COLOR ADJUSTMENTS” key on the touch
panel.
READY TO COPY.
SPECIAL MODES
3
4
OK
●
The COLOR ADJUSTMENTS menu will appear.
DUAL PAGE
COPY
MARGIN SHIFT
CENTERING
COVERS
ERASE
TRANSPARENCY INSERTS
COLOR
IMAGE EDIT
ADJUENTS
1
AUTO
AUTO
8/ 11
2
100%
COPY RATIO
Press the “BRIGHTNESS/INTENSITY/CONTRAST” key
on the touch panel.
EXPOSURE
PAPELECT
SPECIAL MODES
●
ThesettingscreenforBRIGHTNESS/INTENSITY/CONTRAST
OK
COLOR ADJUSTMENTS
will appear.
SUPPRESS
READY TO COPY.
RGB ADJUST
SHARPNESS
INTENSITY
BACKGROUND
OK
OK
COLOR
SPECIAL MODES
BRIGHT INTENS
ONLY ONE FUNCTION IS SELECTABLE.
BRIGHTNESS INTENSITY
BALANCE
CONT
CANCEL
BRIGHTNESS
CONTRAST
CONTRAST
3-24
COLOR ADJUSTMENTS
Select the desired item to be adjusted.
READY TO COPY.
SPECIAL MODES
5
6
7
8
9
●
Select “BRIGHTNESS”, “INTENSITY” or “CONTRAST” on the
touch panel.
OK
OK
BRIGHT
ONLY ONE FUNCTION IS SELECTABLE.
BRIGHTNESS INTENSITY
INTENS
CONT
CANCEL
CONTRAST
Use the “-” and “+” keys to adjust the level of the
selected item.
BRIGHT
INTENS
CONT
CANCEL
OK
ONLY ONE FUNCTION IS SELECTABLE.
BRIGHTNESS
INTENSITY
CONTRAST
Press the upper “OK” key.
READY TO COPY.
OK
BRIGHT
INTENS
CONT
CANCEL
ONLY ONE FUNCTION IS SELECTABLE.
BRIGHTNESS
INTENSITY
CONTR
N
Make all other desired copier selections and enter the
desired number of copies.
INTERRUPT
1
4
2
3
6
5
8
0
CLEAR
ALL
CA
7
9
AUDIT
PROGRAM
C
CLEAR
P
Press the COLOR COPY START (
) key.
INTERRUPT
CLEAR
●
The BLACK COPY START (
) key can be pressed for
3
6
9
copying.However,theBRIGHTNESS/INTENSITY/CONTRAST
setting will be ignored.
CA
ALL
●
TocanceltheBRIGHTNESS/INTENSITY/CONTRASTfunction,
select the BRIGHTNESS/INTENSITY/CONTRAST function
again and press the “CANCEL” key.
PROGRAM
C
CLEAR
P
3-25
IMAGE EDITING FUNCTIONS
The image editing functions include the following items.
●
Single color: Produces copies with a selected single color.
●
Neg./pos. reverse: Copies original image in complementary colors.
●
Mirror image: A mirror image of the original is printed.
●
Photo repeat: Produces repeated images of a photo on a single sheet of copy paper.
●
11 x 17 full-bleed: Produces 11" x 17" full image copies onto 12" x 18" copy paper.
●
Multi-page enlargement: Enlarges an original image to a size larger than 11" x 17" and prints divided images onto
multiple sheets of copy paper for assembly into large composite copy.
Extra size: Allows copying from an extra sized original or onto extra sized paper.
●
These functions are selected by pressing the “IMAGE EDIT” key on the SPECIAL MODES screen and pressing the
key of an individual function.
SINGLE COLOR
The single color function is used to produce copies with a selected
single color.
(Refer to the samples on page 1 to see the effect on copy images in
relation to the SINGLE COLOR function.)
Place the originals on the document glass or in the
optional document feeder tray.
1
Press the SPECIAL MODES key.
2
●
The SPECIAL MODES screen will appear.
READY TO
SPECIAL
MODES
2-SED
CY
Press the “IMAGE EDIT” key on the touch panel.
3
●
The IMAGE EDIT menu will appear.
READY TO COPY.
READY TO COPY.
SPECIAL MODES
OK
OK
OK
SPECIAL MODES
IMAGE EDIT
DUAL PAGE
COPY
ERASE
MARGIN SHIFT
CENTERING
COVERS
NEG./POS.
REVERSE
MIRROR
SINGLE COLOR
TRANSPARENCY INSERTS
IMAGE
11 17
MULTI-PAGE
ENLARGEMENT
COLOR
PHOTO REPEAT
EXTRA SIZE
IMAGEDIT
FULL-BLEED
ADJUSTMENTS
1
AUTO
AUTO
8/ 11
2
0%
COATIO
EXPOSURE
PAPER SELECT
3-26
IMAGE EDITING FUNCTIONS
Press the “SINGLE COLOR” key on the touch panel.
READY TO COPY.
4
●
The setting screen for SINGLE COLOR will appear.
OK
OK
SPECIAL MODES
IMAGE EDIT
READY TO COPY.
NEG./POS.
REVERSE
MIRROR
OK
OK
SPECIAL MODES
SINGLE COLOR
SINGLE OLOR
IMAGE
11 17
MULTI-PAGE
ENLARGEMENT
CANCEL
PHOTO EAT
EXTZE
FULL-BLEED
1
3
RED
2
4
6
GREEN
PURPLE
BROWN
BLUE
5
ORANGE
READY TO COPY.
OK
SPECIAL MODES
SINGLE COLOR
OK
CANCEL
Select the desired color.
5
6
●
The selected color key will be highlighted.
1
3
5
RED
2
4
6
GREEN
PURPLE
BROWN
BLUE
ORANGE
Press the upper “OK” key.
READY TO COPY.
SINGLE COLOR
OK
CANCEL
1
3
5
RED
2
4
6
GREEN
PURPLE
BROWN
BLUE
ORANGE
N
Make all other desired copier selections and enter the
desired number of copies.
INTERRUPT
1
2
3
7
8
4
5
8
0
6
CLEAR
ALL
CA
7
9
AUDIT
PROGRAM
C
CLEAR
P
Press the COLOR COPY START (
) key.
●
To cancel the SINGLE COLOR function, select the SINGLE
COLOR function again and press the “CANCEL” key.
RUPT
3-27
IMAGE EDITING FUNCTIONS
NEG./POS. REVERSE
The NEG./POS. REVERSE function is used to copy the original image
in complementary colors. If this function is selected in the black/white
mode, the black and white areas will be reversed.
Original
Copy
(Refer to the samples on page 2 to see the effect on copy images in
relation to the NEG./POS. REVERSE.)
●
Whenthisfunctionisselected,neithertheCOLORADJUSTMENTS
nor the SINGLE COLOR functions can be selected.
Place the original on the document glass or in the
optional document feeder tray.
1
Press the SPECIAL MODES key.
2
3
4
●
The SPECIAL MODES screen will appear.
READY TO
SPECIAL
MODES
2-SED
CY
Press the “IMAGE EDIT” key on the touch panel.
READY TO COPY.
SPECIAL MODES
●
The IMAGE EDIT menu will appear.
OK
DUAL PAGE
COPY
ERASE
MARGIN SHIFT
CENTERING
COVERS
TRANSPARENCY INSERTS
COLOR
IMAGEDIT
ADJUSTMENTS
1
AUTO
AUTO
8/ 11
2
0%
COATIO
EXPOSURE
PAPER SELECT
Press the “NEG./POS. REVERSE” key on the touch
panel.
READY TO COPY.
OK
OK
SPECIAL MODES
IMAGE EDIT
●
The “NEG./POS. REVERSE” key will be highlighted.
NEG./POS.
RESE
MIRROR
SINGLE COLOR
IMAGE
1
MULTI-PAGE
ENLARGEMENT
PHOTO REPEAT
EXTRA SIZE
FLEED
3-28
IMAGE EDITING FUNCTIONS
Press the upper “OK” key.
5
6
7
OK
NEG./POS.
REVERSE
MIR
I
N
Make all other desired copier selections and enter the
desired number of copies.
INTERRUPT
1
4
2
5
8
0
3
6
CLEAR
ALL
CA
7
9
AUDIT
PROGRAM
C
CLEAR
P
Press the COLOR COPY START (
) key or BLACK
COPY START (
) key.
INTERRUPT
3
●
TocanceltheNEG./POS.REVERSEfunction,pressthe“NEG./
POS. REVERSE” key again on the IMAGE EDIT menu screen.
6
CLEAR
ALL
CA
9
PROGRAM
C
CLEAR
P
3-29
IMAGE EDITING FUNCTIONS
MIRROR IMAGE
This function is used to print a mirror image of the original. The images
Original
Copy
A B
A will beB inverted in the right to left direction on the copies.
C D
C D
Place the originals on the document glass or in the
optional document feeder tray.
1
Press the SPECIAL MODES key.
2
●
The SPECIAL MODES screen will appear.
READY TO
SPECIAL
MODES
2-SED
CY
Press the “IMAGE EDIT” key on the touch panel.
READY TO COPY.
SPECIAL MODES
3
●
The IMAGE EDIT menu will appear.
OK
DUAL PAGE
COPY
ERASE
MARGIN SHIFT
CENTERING
COVERS
TRANSPARENCY INSERTS
COLOR
IMAGEDIT
ADJUSTMENTS
1
AUTO
AUTO
8/ 11
2
0%
COATIO
EXPOSURE
PAPER SELECT
3-30
IMAGE EDITING FUNCTIONS
Press the “MIRROR IMAGE” key on the touch panel.
READY TO COPY.
4
5
6
7
●
The “MIRROR IMAGE” key will be highlighted.
OK
OK
SPECIAL MODES
IMAGE EDIT
NEG./POS.
REVERSE
MIRROR
SINGLE COLOR
GE
11 17
MULTGE
ENLAENT
PHOTO REPEAT
EXTRA SIZE
FULL-BLEED
Press the upper “OK” key.
OK
NEG./POS.
REVERSE
MR
I
N
Make all other desired copier selections and enter the
desired number of copies.
INTERRUPT
1
4
2
5
8
0
3
6
CLEAR
CA
ALL
7
9
AUDIT
PROGRAM
C
CLEAR
P
Press the COLOR COPY START (
COPY START (
) key or BLACK
) key.
INTERRUPT
CLEAR
3
6
●
To cancel the MIRROR IMAGE function, press the MIRROR
IMAGE again on the IMAGE EDIT menu screen.
CA
ALL
9
PROGRAM
C
CLEAR
P
3-31
IMAGE EDITING FUNCTIONS
PHOTO REPEAT
PHOTO REPEAT is used to produce repeated images of a photo on a
single sheet of copy paper.
(Refertothesamplesonpage2toseetheeffectoncopyimagesinrelation
to the PHOTO REPEAT mode.)
Original
Copy
C
C
C
C
B
C
B
B
●
Up to 24 repeats can be made on a single copy sheet. The number of
B
copies on a single sheet depends on the original size and copy paper
size.
B
●
Reduction or enlargement cannot be selected with this function. If
reduction or enlargement has been selected, the copy ratio will be reset
to 100% when this function is selected.
●
This function will not work when non-standard size paper is used.
Place the original on the document glass.
1
●
Theoptionaldocumentfeedercannotbeusedwiththisfunction.
Place 2 ½" x 4" and 2 ½" x 2 ½" originals as shown below.
●
Centering scale
Centering scale
Placing a
~2 " x 2
original
Placing a
~2 " x 4"
original
"
Press the SPECIAL MODES key.
READY TO
SPECIAL
MODES
2
3
●
The SPECIAL MODES screen will appear.
2-SED
CY
Press the “IMAGE EDIT” key on the touch panel.
READY TO COPY.
SPECIAL MODES
●
The IMAGE EDIT menu will appear.
OK
DUAL PAGE
COPY
ERASE
MARGIN SHIFT
CENTERING
COVERS
TRANSPARENCY INSERTS
COLOR
IMAGEDIT
ADJUSTMENTS
1
AUTO
AUTO
8/ 11
2
0%
COATIO
EXPOSURE
PAPER SELECT
3-32
IMAGE EDITING FUNCTIONS
Press the “PHOTO REPEAT” key on the touch panel.
READY TO COPY.
4
●
The setting screen for PHOTO REPEAT will appear.
OK
OK
SPECIAL MODES
IMAGE EDIT
PLEASE SELECT REPEAT TYPE.
NEG./POS.
REVERSE
MIRROR
SINGLE COLOR
OK
OK
SPECIAL MODES
IMAGE
11 17
MULTI-PAGE
ENLARGEMENT
CANCEL
PHOTO REPEAT
PHOTO PEAT
EXTIZE
FULL-BLEED
ORIGINAL SIZE
REPEAT TYPE
81/ 11
2
11 17
1/2
~3 5"
~5 7"
INFOR
LEASE SELECT REPEAT TYPE.
PECIAL MODES
OK
OK
CUS
SETT
Select the desired repeat type.
HOTO REPEAT
CANCEL
ORIGINAL SIZE
REPEAT TYPE
5
6
●
Select the copy paper size depending on the original size.
81/ 11 11 17
2
1/2
●
When making PHOTO REPEAT copies of a ~2 ½" x4" or ~2 ½"
~3 5"
~5 7"
x2½"original,pressthe
keytochangethescreen,andthen
press the desired repeat type key (8 ½" x 11" or 11" x 17") as
appropriate for the original to be copied.
Press the upper “OK” key.
INFORMATIO
EAT TYPE.
OK
CUSTOM
SETTINGS
CANCEL
E
REPEAT TYP
81/ 11 11 17
2
N
Make all other desired copier selections and enter the
desired number of copies.
INTERRUPT
1
4
2
5
8
0
3
7
8
●
If the copier has another paper tray (including the bypass tray)
that holds paper of the same size as the selected paper tray, the
tray can also be selected.
6
CLEAR
ALL
CA
7
9
AUDIT
PROGRAM
C
CLEAR
P
Press the COLOR COPY START (
) key or BLACK
COPY START (
) key.
INTERRUPT
CLEAR
3
6
9
●
To cancel the PHOTO REPEAT function, select the PHOTO
REPEAT function again and press the “CANCEL” key.
CA
ALL
PROGRAM
C
CLEAR
P
3-33
IMAGE EDITING FUNCTIONS
11 x 17 FULL-BLEED
Original
Copy
Inothercopymodes,imagelosswilloccuralongthecopyedges.Whenthe
11 x 17 FULL-BLEED function is used, the full image of an 11" x 17" size
original will be copied onto 12" x 18" size copy paper.
●
Reduction or enlargement cannot be selected with this function. If
reduction or enlargement has been selected, the copy ratio will be reset
to 100% when this function is selected.
11" x 17"
12" x 18"
Place the original on the document glass and close the
document cover.
1
●
Theoptionaldocumentfeedercannotbeusedwiththisfunction.
Press the SPECIAL MODES key.
2
●
The SPECIAL MODES screen will appear.
READY TO
SPECIAL
MODES
2-SED
CY
Press the “IMAGE EDIT” key on the touch panel.
READY TO COPY.
SPECIAL MODES
3
●
The IMAGE EDIT menu will appear.
OK
DUAL PAGE
COPY
MARGIN SHIFT
CENTERING
COVERS
ERASE
TRANSPARENCY INSERTS
COLOR
IMAGEDIT
ADJUSTMENTS
AUTO
AUTO
11 17
0%
COATIO
EXPOSURE
PAPER SELECT
3-34
IMAGE EDITING FUNCTIONS
Pressthe“11x17FULL-BLEED”keyonthetouchpanel.
READY TO COPY.
4
5
●
The “11 x 17 FULL-BLEED” key will be highlighted.
OK
OK
SPECIAL MODES
IMAGE EDIT
NEG./POS.
REVERSE
MIRROR
SINGLE COLOR
IMAGE
11 17
MULTI-PAGE
ENLARGEMENT
PHOTO REPEAT
EXTRA SIZE
FULLEED
Press the upper “OK” key.
OK
NEG./POS.
MR
Load 12" x 18" copy paper into the bypass tray.
6
7
8
Press the “PAPER SELECT” key on the touch panel and
then select the paper type (16 ~ 28 lbs., 28+ ~ 35 lbs. or
35+ ~ 75 lbs.) in the bypass tray.
N
Make all other desired copier selections and enter the
desired number of copies.
INTERRUPT
CLEAR
1
2
5
8
0
3
6
4
CA
ALL
7
9
AUDIT
PROGRAM
C
CLEAR
P
Press the COLOR COPY START (
) key or BLACK
INTERRUPT
COPY START (
) key.
9
3
●
To cancel the 11 x 17 FULL-BLEED function, press the “11 x 17
FULL-BLEED” key again on the IMAGE EDIT menu screen.
6
CLEAR
CA
ALL
9
PROGRAM
C
CLEAR
P
3-35
IMAGE EDITING FUNCTIONS
MULTI-PAGE ENLARGEMENT
This function is used to enlarge an original image to a size larger than 11"
x 17" and print divided images onto multiple sheets of copy paper.
(Refertothesamplesonpage3toseetheeffectoncopyimagesinrelation
to the MULTI-PAGE ENLARGEMENT.)
Press the SPECIAL MODES key.
1
●
The SPECIAL MODES screen will appear.
READY TO
SPECIAL
MODES
2-SED
CY
Press the “IMAGE EDIT” key on the touch panel.
READY TO COPY.
SPECIAL MODES
2
●
The IMAGE EDIT menu will appear.
OK
DUAL PAGE
COPY
ERASE
MARGIN SHIFT
CENTERING
COVERS
TRANSPARENCY INSERTS
COLOR
IMAGEDIT
ADJUSTMENTS
1
AUTO
AUTO
8/ 11
2
0%
COATIO
EXPOSURE
PAPER SELECT
Press the “MULTI-PAGE ENLARGEMENT” key on the
touch panel.
READY TO COPY.
3
OK
OK
SPECIAL MODES
IMAGE EDIT
●
The setting screen for MULTI-PAGE ENLARGEMENT will
appear.
NEG./POS.
REVERSE
MIRROR
SINGLE COLOR
IMAGE
PLEASE SELECT ENLARGEMENT SIZE AND
ORIGINAL SIZE.
11 17
MULTI-PAGE
ENLAMENT
PHOTO REPEAT
EXTRA SIZE
FULL-BLEED
SPECIAL MODES
OK
OK
MULTI-PAGE ENLARGEMENT
CANCEL
ENLARGEMENT SIZE
ORIGINAL SIZE & ORIENTATION
11 17
22 17 22 34
81/ 14
2
MULTI-PAGE ENLARGEMENT
81/ 11
34 44 44 68
2
2-SIDED
COPY
ENLARGEMENT SIZE
ORIGINAL
11 1
22 17 22 34
OUTPUT
81/ 1
2
Select the desired enlargement size.
34 44 4 68
81/ 1
4
●
Select the desired size among the sizes displayed on the touch
panel.
2
3-36
IMAGE EDITING FUNCTIONS
AGE ENLARGEMENT
EMENT SIZE
CANCEL
OK
Select the original size.
ORIGINAL SIZE & ORIENTATI
11 17
5
6
7
8
9
●
The original sizes that can be used depend on the selected
enlargement size.
7 22 34
81/ 14
81/
2
●
The original orientation will be indicated depending on the
selected enlargement size and original size.
4 44 68
Press the upper “OK” key.
OK
T
CANCEL
ORIGINAL SIZE & ORIEION
Place the original on the document glass in accordance
with the indicated orientation.
●
The area of the original that has been specified on the touch
panel will be scanned.
●
Theoptionaldocumentfeedercannotbeusedwiththisfunction.
N
Make all other desired copier selections and enter the
desired number of copies.
INTERRUPT
1
4
2
5
8
0
3
6
●
The paper tray will be automatically selected. If the copier has
another paper tray (including the bypass tray) that holds the
paper of the same size as the selected paper tray, the tray can
also be selected.
CLEAR
ALL
CA
7
9
AUDIT
PROGRAM
C
CLEAR
P
Press the COLOR COPY START (
) key or BLACK
INTERRUPT
CLEAR
COPY START (
) key.
3
6
●
The original image will be divided and copied onto multiple
sheets of paper. Overlapped areas will be made along the
leading and trailing edges of each copy.
CA
ALL
●
To cancel the MULTI-PAGE ENLARGEMENT function, select
the MULTI-PAGE ENLARGEMENT function again and press
the “CANCEL” key.
9
PROGRAM
C
CLEAR
P
3-37
IMAGE EDITING FUNCTIONS
EXTRA SIZE
The EXTRA SIZE function provides a method for entering the dimensions
of non-standard size copy paper and non-standard size originals for the
purpose of automatic enlargement or reduction of the image for a best fit
onto the copy paper.
★ KEY OPERATOR Extra paper size setting for each individual paper tray
of the copier can be made. See page 22 of the KEY OPERATOR’S GUIDE.
Place the non-standard original on the document glass
or the non-standard copy paper into the bypass tray.
1
●
Either one or both can be set.
Press the SPECIAL MODES key.
2
●
The SPECIAL MODES screen will appear.
READY TO
SPECIAL
MODES
2-SED
CY
Press the “IMAGE EDIT” key on the touch panel.
READY TO COPY.
SPECIAL MODES
3
●
The setting screen for IMAGE EDIT selections will appear.
OK
DUAL PAGE
COPY
ERASE
MARGIN SHIFT
CENTERING
COVERS
TRANSPARENCY INSERTS
COLOR
IMAGEDIT
ADJUSTMENTS
1
AUTO
AUTO
8/ 11
2
0%
COATIO
EXPOSURE
PAPER SELECT
3-38
IMAGE EDITING FUNCTIONS
Press the “EXTRA SIZE” key on the touch panel.
READY TO COPY.
4
●
The setting screen for EXTRA SIZE will appear.
OK
OK
SPECIAL MODES
IMAGE EDIT
●
If an original on the document glass or paper in the bypass tray
issetonopeningtheEXTRASIZEscreen,theoriginalandpaper
dimensions in X (horizontal) and Y (vertical) will be shown
respectively on the ORIGINAL SIZE tab and the PAPER SIZE
FOR BYPASS tab.
NEG./POS.
REVERSE
MIRROR
SINGLE COLOR
IMAGE
11 17
MULTI-PAGE
ENLARGEMENT
PHOTO REPEAT
EXTRIZE
FULL-BLEED
Asastartingpoint, thedimensionsshownforextrasizeoriginals
or paper will be the closest match to standard sizes.
READY TO COPY.
OK
EXTRA SIZE
CANCEL
OK
(5 1/2~17)
inch
1
X
8
/
2
(4~11 3/4)
inch
1
Y
5
/
2
ENABLE AUTO SIZE DETECTION
ORIGINAL SIZE
PAPER SIZE FOR BYPASS
READY TO COPY.
OK
EXTRA SIZE
CANCEL
OK
(5 1/2~17)
inch
1
X
8
/
2
(4~11 3/4)
inch
1
Y
5
/
2
ENABLE AUTO SIZE DETECTION
PAPER SIZE FOR BYPASS
ORIGINAL SIZE
Adjust the original size on the “ORIGINAL SIZE” tab and
paper size on the “PAPER SIZE FOR BYPASS” tab,
respectively.
READY TO COPY.
EXTRA SIZE
5
OK
CANCEL
OK
●
Adjust each X (horizontal) and Y (vertical) dimension using the
(5 1/2~17)
1
and
keys.
X
12
/
4
inch
(4~11 3/4)
inch
●
Y
4
Ifthe“ENABLEAUTOSIZEDETECTION”checkboxischecked
on either tab, the size detection function will be activated. In this
ENABLE AUTO SIZE DETECTION
case, the“X/Y”keysand “
to allow any input.
/
”keyswillbegrayedoutnot
ORIGINAL SIZE
PAPER SIZE FOR
READY TO COPY.
OK
EXTRA SIZE
CANCEL
OK
(5 1/2~17)
inch
X
Y
(4~11 3/4)
inch
ENABLE AUTO SIZE DETECTION
ORIGINAL SIZE
PAPER SIZE FOR BYPASS
3-39
IMAGE EDITING FUNCTIONS
Press the upper “OK” key on the touch panel.
I
6
OK
CANCEL
(5 1/2~17)
1
Press the “AUTO IMAGE” key on the touch panel.
7
8
●
Refer to page 2-11 for the AUTO IMAGE function.
11
17
14
AUTO IMAGE
1
/ Y-4
10%
4
SELECT
COPY TIO
Enter the desired number of copies and press either of
the COLOR COPY START (
START ( ) key.
INTE
TERRUPT
1
4
2
5
8
0
3
) key or BLACK COPY
6
9
CLE
CLEAR
ALL
CA
AL
7
C
PROGRAM
AUDIT
C
CL
PCLEAR
3-40
CHAPTER 4
SUPPLIES
This chapter describes the supplies for this copier such as paper and
toner.
Page
●
PAPER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Types and sizes of copy paper . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Loading copy paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
●
ADDINGTONER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
●
USEDTONER DISPOSAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
●
STORAGE OF SUPPLIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
4-1
PAPER
Types and sizes of copy paper
Size
Weight
Capacity
Special paper
(20 lb. bond paper)
Paper trays
Bypass tray
5-1/2" x 8-1/2"
to 11" x 17"
16 lbs. to 28 lbs.
500 sheets
50 sheets
5-1/2" x 8-1/2"
to 12" x 18"
16 lbs. to 75 lbs.
(Ordinary paper)
Transparency film, cover stock
(104 lbs.), index stock (155 lbs.)
●
For best results, use only paper recommended by SHARP.
Loading copy paper
“OPEN TRAY AND ADD PAPER.” will be displayed when there is
no copy paper in a selected paper feed station.
When a selected paper tray is not installed or is improperly installed,
“PUSH PAPER TRAY INTO MACHINE UNTIL IT LATCHES.”
will be displayed. Install it or push it back firmly into place.
For best results, use only Sharp recommended paper.
4-2
PAPER
Loading paper in the paper trays
Gently lift and pull out the paper tray.
1
Fan the copy paper and insert it into the tray.
2
3
●
The tray holds 500 sheets of 20 lb. bond paper.
Do not load paper above the maximum height line.
Maximum height line
Push the paper tray firmly back into the copier.
4-3
PAPER
Changing the copy paper size in the tray
Gently lift and pull out the paper tray until it stops.
1
Adjust the paper size indicator to match the paper size
to be set.
2
3
4
●
Slidethepapersizeindicatortotherightorlefttomatchthepaper
size.
Paper size indicator
Adjust the front guide and left guide while squeezing
their lock levers.
●
Slidethefrontandleftguidestomatchthewidthandlengthofthe
copy paper.
Left guide
Front guide
Load copy paper into the tray.
Maximum height line
Place the paper size card in the front of the paper tray.
5
6
●
The paper size card has three faces. Fold the card properly to
Paper size card
show the selected paper size. The paper size indication which
showsthroughtheslotonthefrontofthecopiershouldmatchthe
selected paper size.
Push the paper tray firmly back into the copier.
4-4
ADDING TONER
The message “
TONER SUPPLY IS LOW.
” will appear in
For best copying results, be sure to use
only Sharp Genuine Supplies which are
designed, engineered, and tested to
maximize the life and performance of
Sharp copiers.
the message display before the toner supply is completely empty.
(
indicate toner types. : yellow, : magenta, : cyan,
:
Y
M
C
BK
black)Ifcopyingiscontinued,copieswillgraduallybecomelighteruntil
the copier stops and the message display changes to “ADD
TONER.PRESS .” indicating that the toner supply is empty. Toner
Look for the Genuine Supplies label on
the toner package.
can be added any time after the message “
TONER SUPPLY IS
LOW. ”appears.Toaddtoner,stopthecopierandproceedasbelow.
When either message appears, you can use the INFORMATION key
for detailed information as necessary.
If any color toner supply is empty, color copying cannot be performed.
However, black/white copying can be performed unless the black
toner supply is empty.
During long copy runs of multiple originals containing many images
and/ordarkshades,“TONERREPLENISHMENTINPROGRESS.”may
appear and the copier may stop making copies even though toner is
left.
GENUINE SUPPLIES
The copier will automatically cycle and replenish the toner to the
normal level and then the START key indicator will light up. Press the
START key to resume copying.
Open the front cover.
1
Push the lock release buttons on both sides of the toner
box and pull the toner box out slowly until it stops.
2
●
The toner hoppers are located as below.
Magenta
Cyan
Black
Yellow
4-5
ADDING TONER
Tap on the top of the new toner cartridge 5 times. Then
hold the toner cartridge horizontally and vigorously
shake it about 20 times. This will loosen the toner and
allow it to flow more easily into the toner hopper.
3
4
5
6
20 x
5 x
CAUTION
Besuretoperformthesesteps.Ifnot,tonermaynotfloweasilyinto
the toner hopper.
Place the new toner cartridge with the protrusions into
the notches of the relevant toner hopper as shown.
●
The left example shows the toner hopper of black toner.
Slide the toner cartridge along the guides over the toner
hopper.
Hold the toner cartridge with one hand while pulling on
the sealing tape to remove it.
●
It will take about 40 seconds for the cartridge to empty.
Sealing tape
4-6
ADDING TONER
Tap on the top of the toner cartridge to ensure that the
cartridge completely empties.
7
8
9
CAUTION
Be sure to perform this step. If not, some toner may be scattered
when the cartridge is removed.
Slide the empty toner cartridge back along the guides
and remove it.
●
The cartridge opening will be closed as it is moved back along
the guides.
Push the toner box back into the copier.
Close the front cover.
10 NOTE:
Add only one cartridge of the color toner indicated as being low or
empty.
4-7
USED TONER DISPOSAL
“REPLACEUSEDTONERCONTAINER.PRESS FORGUIDANCE.”
will appear when the toner collecting container is full.
Thecopierwillstopandwillnotoperateuntilanewcontainerhasbeen
installed. Replace the toner collecting container as described below.
Whentheabovemessageisdisplayed,youcanusetheINFORMATION
key for detailed information as necessary.
Open the toner collecting container cover.
1
2
●
Push once on the door to unlatch and open it.
Disengage and remove the container from the copier.
●
Toner cannot be reused. Do not transfer used toner to the toner
hopper.
●
Remove the cap from a new toner collecting container and use
it to cover the full toner collecting container.
●
Keep the full toner collecting container until the next regular
service call. Your authorized Sharp Service Technician will
collect the container for disposal.
New container
Removed container
Installanewtonercollectingcontaineruntilitclicksinto
place.
3
4
Close the toner collecting container cover.
4-8
STORAGE OF SUPPLIES
The supplies of this copier replaced by the user include copy paper,
toner, toner collecting container, and staple cartridges for the optional
staple sorter (AR-SS2) and the finisher (AR-FN4).
For best copying results, be sure to use
only Sharp Genuine Supplies which are
designed, engineered, and tested to
maximize the life and performance of
Sharp copiers. Look for the Genuine
Supplies label on the toner package.
GENUINE SUPPLIES
Photoconductive drum
The AR-C160 Copier has advanced process control technology
which improves copy quality uniformity. This feature stabilizes copy
qualitythroughoutthelifeofthephotoconductivedrumbyautomatically
compensating for the changes in drum characteristics due to wear,
operator use patterns, and environmental conditions. The automatic
adjustments are made in response to a sensor that detects the
reflectance characteristics of the drum.
WARNING
This feature requires drums containing the special reflectance area
(recommended Sharp genuine photoconductive drum), to prevent
low image density copies from poor process control and possible
damage to the machine. If you use other drums, the process control
system cannot run properly.
Proper storage
Store the supplies in a location that is:
1
●
●
●
clean and dry,
at a stable temperature,
not exposed to direct sunlight.
Store copy paper in the wrapper and lying flat.
2
●
Paperstoredinpackagesstandinguporoutofthewrappermay
curl or become damp, resulting in paper misfeeds.
4-9
CHAPTER 5
COPIER TROUBLE?
This chapter describes how to remove misfed originals and paper and
other common trouble remedies.
Page
●
MISFEED REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
●
MAINTENANCE REQUIRED . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
●
TONER COLLECTING CONTAINER OFTRANSFER UNIT . . . 5-12
●
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13
5-1
MISFEED REMOVAL
When a misfeed occurs, the copier will stop.
If paper becomes accidentally torn during removal, be
The message “MISFEED HAS OCCURRED. CLEAR
sure to remove all pieces. Be careful not to damage the
photoconductive drum or the corona wires.
INDICATED AREA. PRESS
FOR RECOVERY
INSTRUCTIONS.” will appear with a display of paper
misfeed locations. Press the INFORMATION key for
more detailed information as necessary.
First confirm the misfeed locations.
For misfeeds in an optional staple sorter, see page 7-13.
Formisfeedsinanoptionallargecapacitytray, seepage
7-17.
For misfeeds in an optional finisher, see page 7-26.
(
P. 5-2)
(
P. 5-6)
(
(
P. 5-3)
P. 5-5)
(
P. 5-9)
MISFEED HAS OCCURRED.
Misfeed in the optional RADF
When the optional RADF misfeeds an original sheet, the copier will
stop and the misfeed message will appear.
CLEAR INDICATED AREA.
PRESS
FOR RECOVERY INSTRUCTIONS.
An original misfeed may occur at one of three locations:
(A) in the RADF feed section, (B) in the exit roller, or (C)
under the transport belt.
A
C
B
5-2
MISFEED REMOVAL
(A) Openthefeedingrollercoverandpulltheoriginalgently
to the right and out from the document feeder tray.
Feeding roller cover
●
Be sure to open and close the document feeder cover to cancel
the misfeed display.
(B) Open the exit roller cover and gently pull the original
out.
●
Be sure to open and close the document feeder cover to cancel
the misfeed display.
Exit roller cover
(C) Open the feeding roller cover and the document feeder
cover, and remove the original.
NOTE:
After misfed originals are removed from locations A, B and/or C, a
messagemayappearindicatingthenumberoforiginalswhichmust
be returned to the document feeder tray. Return the originals and
press the START key to resume copying.
MISFEED HAS OCCURRED.
Misfeed in the bypass tray
CLEAR INDICATED AREA.
PRESS FOR RECOVERY INSTRUCTIONS.
Open the front cover.
1
5-3
MISFEED REMOVAL
Turn the transport lever to the left.
2
3
4
5
6
●
Do not pull out the paper transport in this step.
A
Turn roller rotating knob
to feed the misfed paper into the copier.
in the direction of the arrow
●
Donotpullthemisfedpaperoutthroughthebypasstraybecause
unfixed toner may soil the inside of the copier.
Roller rotating knob A
Pull out the paper transport.
Remove the misfed paper.
Push the paper transport back securely into the copier
and turn the transport lever back.
5-4
MISFEED REMOVAL
Close the front cover.
7
MISFEED HAS OCCURRED.
Misfeed in the paper trays
CLEAR INDICATED AREA.
PRESS FOR RECOVERY INSTRUCTIONS.
Open the right side covers.
1
●
Grasp the handle and gently open the cover.
Remove the misfed paper.
2
3
●
Be careful not to tear the misfed paper during removal.
If the paper cannot be seen from the side, pull out the
paper tray which was in use and remove the misfed
paper.
●
Be careful not to tear the misfed paper during removal.
5-5
MISFEED REMOVAL
Close the paper tray and the side covers.
4
●
Confirm that the misfeed display is cleared.
MISFEED HAS OCCURRED.
Misfeed in the transport area, exit area and
fusing area
CLEAR INDICATED AREA.
PRESS FOR RECOVERY INSTRUCTIONS.
Open the front cover.
1
Turn the transport lever to the left.
2
3
●
Do not pull out the paper transport in this step.
Check to see if any paper is misfed in the exit area.
Roller rotating knob B
●
B
If any paper is misfed, turn roller rotating knob in the direction
of the arrow to remove the misfed paper.
NOTE:
B
Be sure to turn roller rotating knob
only in the direction of the
arrow. Iftheknobisturnedintheoppositedirection, thecopiermay
malfunction.
5-6
MISFEED REMOVAL
Open the upper right side cover to check to see if any
paper is misfed.
4
1
Grasp the handle and open the cover.
A
2
If any misfed paper is seen, turn roller rotating knob
in the
direction of the arrow to feed the misfed paper into the copier.
Roller rotating knob A
3
Gently close the upper right side cover.
Caution
Pull out the paper transport.
5
6
Remove any misfed paper from the paper transport.
●
Ifmisfedpaperhasbeenfedintothecopierinstep4orpaperhas
misfed on the transport belt, gently remove misfed paper not to
touch the belt.
5-7
MISFEED REMOVAL
If the misfed paper is in the fusing unit:
1
Open the fusing unit cover in the direction of the arrow.
CAUTION
The fusing unit is hot. Use care in removing paper.
B
2
Turn roller rotating knob
remove the misfed paper.
in the direction of the arrow to
Roller rotating knob B
NOTE:
Be sure to turn roller rotating knob
B
only in the direction of the
arrow. Iftheknobisturnedintheoppositedirection, thecopiermay
malfunction.
3
Return the fusing unit cover securely to its original position.
Push the paper transport back securely into the copier
and turn the transport lever back.
7
8
Close the front cover.
●
Confirm that the misfeed display is cleared.
5-8
MISFEED REMOVAL
MISFEED HAS OCCURRED.
Misfeed in the optional duplex module
NOTES:
●
For misfeed removal from an optional staple sorter (AR-SS2) or an
optional finisher (AR-FN4), please refer to chapter 7 Optional
Equipment.
●
If any other misfeed locations are indicated, be sure to remove any
misfed paper from these locations before pulling out the duplex
module. If not, a sheet of paper in another location may become torn
and difficult to remove.
CLEAR INDICATED AREA.
PRESS FOR RECOVERY INSTRUCTIONS.
Open the left side cover.
1
Remove the misfed paper.
Close the left side cover
Pull out the duplex module.
2
3
4
5-9
MISFEED REMOVAL
Remove the misfed paper.
5
6
C
●
Turn roller rotating knob
remove the misfed paper.
in the direction of the arrow and
Roller rotating knob C
●
Slide the paper guide if needed.
Push the duplex module back into the copier.
5-10
MAINTENANCE REQUIRED
Whenthemessage“READYTOCOPY.(MAINTENANCEREQUIRED.
CODE: )”appearsinthemessagedisplay,servicebyanauthorized
Sharp Service Technician will be required soon. Contact your Service
Center as soon as possible.
5-11
TONER COLLECTING CONTAINER OF
TRANSFER UNIT
Whenthemessage“TONERCOLLECTINGCONTAINEROFTRANSFER
UNIT IS FULL. CALL FOR SERVICE.” appears in the message
display, contact your Service Center.
5-12
TROUBLESHOOTING
Always check the message display whenever the copier stops or
operation is not possible. The messages will give you easy-to-follow
directions. Ifthemessagesdonotgivespecific instructions, checkthe
list below.
Problem
Solution
●
●
Copier plugged in?
Power switch on?
Plug the copier into a grounded outlet.
Copier does not operate.
Turn the power switch on.
See page 2-16.
●
●
Copy density properly adjusted?
Copies are too dark or too
light.
Istheoriginalplacedfacedownon Place the original face down on the
the document glass or face up in documentglassor faceupintheRADF.
the optional RADF?
Blank copies.
●
Paper too heavy?
Paper damp?
Use copy paper within the specified
range. See page 4-2.
Copies smear if rubbed.
●
●
Replace with dry copy paper. Be sure
to store copy paper in a dry location.
Copy size is different from
the selected paper size.
Paper size indicator properly set? When changing the copy paper size in
a tray, be sure to adjust the paper size
indicator. See page 4-4.
5-13
TROUBLESHOOTING
Problem
Solution
Use standard paper.
●
Non-standard paper used?
If using special papers, feed the paper
through the bypass tray.
●
●
Paper misfeeds frequently.
Is paper properly installed?
See pages 2-14 and 4-2.
Pieces of paper inside copier?
Removeallpiecesofmisfedpaper.See
page 5-2.
●
●
Paper curled or damp?
Storecopypaperflatinthewrapperina
dry location. See page 4-9.
Dust, dirt, smudges appear
on copies.
Document glass, optional
document cover or optional
RADF transport belt dirty?
Clean regularly. See page 6-6.
●
Touch panel is too dark or
too light.
Is LCD contrast properly
adjusted?
Adjust the LCD contrast.
See page 6-7.
If a problem persists after checking the above, please consult your
authorized Sharp Service Center.
Self-diagnostic function
Anautomaticself-diagnosticfunctionisbuiltintothiscopier.Shouldthe
copiermalfunction, theself-diagnosticfunctionwilllocatetheproblem
and stop the copier to prevent damage. An alphanumeric code will
appear in the message display.
Example
Should the copier stop completely, and the message “CALL FOR
SERVICE. CODE: - ” appear in the message display, contact
your authorized Sharp Service Center.
★ KEY OPERATOR See page 35 of the KEY OERATOR’S GUIDE.
5-14
CHAPTER 6
GENERAL INFORMATION
This chapter describes general information for using this copier.
Page
●
PART NAMES AND FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Interior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
Operation panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
Touch panel (Basic screen) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
USER MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
TOUCH PANEL CONTRAST ADJUSTMENT . . . . . . . . . . . . . . . 6-7
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
●
●
●
6-1
PART NAMES AND FUNCTIONS
[AR-C160 with optional document cover]
Exterior
[Optional RADF]
Exit tray
Paper trays
Finished copies are deposited in the exit tray.
Each tray holds 500 sheets of 20 lb. bond paper.
Power switch
Front cover
Press to turn copier power on and off.
Open to remove misfeeds and to service the
copier.
Operation panel
All copier controls are located here for easy
operation.
Right side covers
Open to remove misfeeds in the paper feed area.
Original holder (optional)
Document glass
Keep originals here.
All originals which cannot be copied from the
optional RADF must be copied here.
Document cover (optional)
Place the original on the document glass and close
the document cover before copying starts.
Paper clip tray
Keep paper clips here.
Toner collecting container cover
Bypass tray paper guides
Open to replace the toner collecting container.
Adjust to the width of the copy paper.
Duplex module or 500-sheet paper drawer
(optional)
The copier can be equipped with either a duplex
module or a 500-sheet paper drawer. When
neither is installed, the opening is covered. The
duplex module provides duplex copying capability.
Bypass tray
Special papers (including transparency film) and
copy paper can be fed from the bypass tray.
6-2
PART NAMES AND FUNCTIONS
Interior
Fusing unit
RADF feeding roller cover (optional)
The fusing unit is hot. Exercise care in this area.
Open to remove misfed originals.
Roller rotating knobs
Turn to remove misfed paper.
Document feeder indicators (document feeder
is optional)
Original feed indicator
Indicates the originals in the tray will be fed.
Original reminder
Transport lever
Turn to pull out the paper transport.
Indicates an original is still on the document glass.
Paper transport
Pull out to remove misfed paper.
Original guides (optional)
Adjust to the size of the originals.
NOTE:
Document feeder tray (optional)
Follow information messages for misfeed removal
procedure. (See page 5-2 to 5-10.)
Holds up to 50 originals.
RADF exit area (RADF is optional)
Finished originals are output here.
Accessories
RADF exit roller cover (RADF is optional)
Operation manual . . . . . . . . . . . . . . . . . . . . . 1
Key operator’s guide . . . . . . . . . . . . . . . . . . . 1
Toner collecting containers
Open to remove misfed originals.
Toner box
Contains four toner hoppers. Each toner hopper
contains relevant color toner or black toner.
(including 1 pre-installed at the factory) . . . . . 2
6-3
PART NAMES AND FUNCTIONS
Operation Panel
INFORMATION
SPECIAL
MODES
INTERRUPT
CLEAR
1
4
2
5
8
0
3
6
DATA ON LINE
CUSTOM
SETTINGS
2-SIDED
PRINT
COPY
COPY
CA
ALL
7
9
OUTPUT
AUDIT
PROGRAM
C
CLEAR
P
The key and
indicators are not
used for the copier
features.
C
CLEAR ( ) key
LCD touch panel
Press to clear the copy quantity display, or press
during a copy run to terminate copying. The
copier will stop after copies in progress are
finished.
Displays information to assist the operator.
Various operation keys are included in the touch
panel depending on the particular screen being
displayed.
10-key pad
COLOR COPY START (
indicator
) key and
Used to set the copy quantity.
Color copying is possible when the indicator is on.
Press to start color copying.
INTERRUPT key and indicator (p. 2-20)
Interrupts a copy run.
BLACK COPY START (
) key and indicator
Black/white copying is possible when the
indicator is on.
Press to start black/white copying.
CLEAR ALL ( CA ) key
Clears all selected settings and returns the copier
to the initial settings.
SPECIAL MODES key (p.3-1)
COPY key
Press to select special functions.
Press to return to the COPY mode when the
PRINT mode is active. If pressed in the COPY
mode, the total output count will be displayed
during the key press.
Message display
Messages are displayed regarding copier status
and operation.
Press to exit the sleep mode.
AUDIT key
Paper size display
Press to enter the account number if the auditing
mode has been set for only the color copy mode.
Also closes an open account.
The sizes of loaded copy paper are displayed and
the selected paper feed location is highlighted.
indicates the amount of copy paper.
PROGRAM (
) key (p. 2-18)
P
Copy quantity display
Press to select the job memory mode.
Displays the specified number of copies.
Original size display
The original paper size is displayed.
6-4
PART NAMES AND FUNCTIONS
Touch Panel (Basic screen)
INFORMATION
READY TO COPY.
SPECIAL
MODES
1
ORIGINAL
82 11
CUSTOM
SETTINGS
1
82 11R
2-SIDED
COPY
1
1.
82 11
OUTPUT
2.
11 17
1
3.
82 14
1
AUTO
AUTO
8/ 11
100%
2
EXPOSURE
PAPER SELECT
COPY RATIO
INFORMATION key (p. 1-7)
PAPER SELECT display
Press for operation guidance on use of various
features of this copier.
Press for guidance when a misfeed occurs, when
adding toner, or when used toner must be
disposed of.
Displays the selected paper size. When “AUTO”
is displayed, paper size matching the original and
copy ratio will be automatically selected.
PAPER SELECT key
Press to select the desired paper tray.
CUSTOM SETTINGS key
Press to set key operator programs or adjust the
contrast of the touch panel.
COPY RATIO display
Displays the copy ratios for reductions or
enlargements.
2-SIDED COPY key
Press to select the 1-sided to 1-sided, 1-sided to
2-sided*, 2-sided to 2-sided* or 2-sided to
1-sided* copy mode.
* To select the 1-sided to 2-sided or 2-sided to
2-sided copy mode, an optional duplex module
(AR-DU2N) must be installed. To select the
2-sided to 1-sided or 2-sided to 2-sided copy
mode, an optional RADF must be installed.
COPY RATIO key
Press to select a reduction or enlargement copy
ratio or select the automatic copy ratio selection
mode.
Initial settings
OUTPUT key
The copier assumes the initial settings when it is
turned on, when the CLEAR ALL ( CA ) key is pressed,
and approximately 1 minute after the last copy is
made in any mode.
Press to select the sorter mode when an optional
staple sorter (AR-SS2) is installed.
EXPOSURE display
●
Copy ratio: 100%
●
Automatic exposure, TEXT/PRTD. PHOTO mode
Copy quantity: 0
Indicates the selected exposure mode.
●
●
All special copier modes are set to off.
Tray select: Paper tray 1.
Optional large capacity tray will be selected when
installed.
EXPOSURE key (p. 2-16)
●
Press to select the exposure mode: AUTO or
MANUAL and TEXT/PRTD. PHOTO, TEXT/
PHOTO, TEXT, PHOTO, PRINTED PHOTO or
MAP. The COPY OF COPY and COLOR TONE
ENHANCEMENT modes can also be selected
with this key.
★ KEY OPERATOR
Initial settings can be
programmed as desired. The auto clear time can also
be changed. See pages 21 and 25 of the KEY
OPERATOR’S GUIDE.
6-5
USER MAINTENANCE
Thedocumentglass,theoptionaldocumentcoverorthetransportbelt
oftheoptionalRADFmustbekeptcleantoavoiddirtyareasfrombeing
copied onto the copies.
Document glass and document cover
Wipe the document glass, the optional document cover
or the transport belt of the optional RADF with a soft,
clean cloth.
●
If necessary, dampen the cloth with water. Do not use thinner,
benzene, or similar volatile cleaning agents.
6-6
TOUCH PANEL CONTRAST ADJUSTMENT
The contrast of the touch panel can be adjusted as below.
Press the CUSTOM SETTINGS key.
1
1
CUSTOM
SETTINGS
4
7
Press the “DISPLAY CONTRAST” key on the touch
panel.
EXI
ETTINGS
2
3
4
KEY OPERATOR
PROGRAMS
DISPLAY
CONTRAST
Press the “LIGHTER” or “DARKER” key to adjust the
contrast.
TTINGS
ONTRAST
LIGHTER
DARKER
Press the “OK” key.
OK
R
DARKER
6-7
SPECIFICATIONS
COPIER
Type
Console
Copy system
Originals
Dry, electrostatic transfer system
Sheets, bound documents
Max. 11" x 17"
Original sizes
Copy paper sizes
Max. 12" x 18", min. 5-1/2" x 8-1/2"
Image loss: Max. 13/64" (5 mm) (leading edge)
Max. 9/32" (7 mm) (trailing edge)
Max. 1/4" (6 mm) (along all other edges in total)
Black/White:
32 copies/min. (8-1/2" x 11")
Copying speed
Color:
16 copies/min. (8-1/2" x 11")
11 copies/min. (8-1/2" x 11"R) 22 copies/min. (8-1/2" x 11"R)
9 copies/min. (8-1/2" x 14")
7 copies/min. (11" x 17")
17 copies/min. (8-1/2" x 14")
15 copies/min. (11" x 17")
Continuous copy
First-copy time*
Max. 999 copies; subtractive counter
Color : 9.8 sec. , Black/White : 19.5 sec.
*From the first tray. In the default setting.
Warm-up time
Copy ratio
Approx. 330 sec. (at 68°F)
Variable: 25 to 400% in 1% increments, total 376 steps
(can be set in the horizontal and vertical directions independently)
Fixed presets: 25%, 50%, 64%, 77%, 95%, 100%, 121%, 129%,
141%, 200%, 400%
Exposure system
Copy paper feed
Moving optical source (stationary platen) with automatic exposure
function
Three paper trays with automatic paper feed (500 sheets each);
one bypass tray with 50-sheet automatic feed capability
Fusing system
Developer system
Light source
Heat rollers
Magnetic brush development
Halogen lamp
Resolution
Scan: 600 dpi
Output: 600 dpi
Gradation
Scan: 256 levels
Output: 256 levels
Required power supply
Power consumption
Overall dimensions
AC 120V, 60 Hz, 12 amperes
Max. 1.5 kW
55-19/32" (W) x 27-3/8" (D)
(1412 mm (W) x 695 mm (D))
Weight
Approx. 335 lbs. (152 kg)
6-8
SPECIFICATIONS
Copier dimensions
(with optional document
cover)
29-17/32" (W) x 27-3/8" (D) x 41-47/64" (H)
(750 mm (W) x 695 mm (D) x 1060 mm (H))
Opperating conditions*
Temperature: 59°F to 95°F (15°C to 35°C)
Humidity:
20% to 80%
* If the temperature is higher than 86°F (30°C), the humidity should be
lower than 60%.
Optional equipment
Document cover (AR-VR2)
Reversing automatic document feeder (AR-RF1)
20-bin staple sorter (AR-SS2)
Finisher (AR-FN4)
Large capacity tray (AR-LC2N)
500-sheet paper drawer (AR-CS2N)
Duplex module (AR-DU2N)
Fiery print controller (AR-PE2)
Print engine power supply unit (AR-PX4)
REVERSING AUTOMATIC DOCUMENT FEEDER (optional)
Acceptable originals
Single-sided originals: 14 to 34 lbs.
Weight: Two-sided originals: 14 to 34 lbs. for 5-1/2" x 8-1/2"and
8-1/2" x 11" originals.
14 to 29 lbs. for 8-1/2"x 14" and 11" x 17" originals.
Size: 5-1/2" x 8-1/2" to 11" x 17"
Capacity: Up to 50 sheets for 5-1/2" x 8-1/2" and 8-1/2" x 11" originals provided
the total aggregate thickness does not exceed 1/4" or 6.5 mm (14 to
20 lbs.) or 3/16" or 5 mm (21 to 34 lbs.) Up to 30 sheets for 8-1/2" x
14" and 11" x 17" originals.
DUPLEX MODULE (optional)
Paper type
Ordinary paper only
1 (trayless system)
Number of copies
Copy paper size
5-1/2" x 8-1/2", 7-1/4" x 10-1/2"R, 8-1/2" x 11", 8-1/2" x 11"R,
8-1/2" x 13", 8-1/2" x 14", 11" x 17"
Copy paper weight
15 lbs. to 28 lbs.
6-9
SPECIFICATIONS
Acoustic Noise Emission (measurement according to ISO7779)
Printing mode
Standby mode
Black/White
Color
6.3B
Sound power level LwA
6.4B
5.2B
Sound pressure
level LpA
Bystander positions
Operator position
50dB(A)
50dB(A)
48dB(A)
49dB(A)
24dB(A)
24dB(A)
Emission Concentration (measurement according to RAL UZ62)
Ozone
Dust
0.02 mg/m3 or less
0.075 mg/m3 or less
0.07 mg/m3 or less
Styrene
Specifications are subject to change for improvement without notice.
6-10
CHAPTER 7
OPTIONAL EQUIPMENT
Thischapterdescribesoperatinginstructionsforthe20-BinStapleSorter
(AR-SS2), Large Capacity Tray (AR-LC2N) and Finisher (AR-FN4).
Page
●
SYSTEM CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
●
20-BIN STAPLE SORTER (AR-SS2) . . . . . . . . . . . . . . . . . . . . . . 7-3
Part names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Using the staple sorter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4
Sorter capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
Staple sort . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6
Manual stapling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8
Staple cartridge replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9
Staple jam removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11
Misfeed removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-13
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-14
●
LARGE CAPACITYTRAY (AR-LC2N) . . . . . . . . . . . . . . . . . . . . 7-15
Part names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-15
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-15
Loading copy paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-16
Misfeed removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-17
●
FINISHER (AR-FN4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-19
Part names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-19
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-19
Offset stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-20
Staple print . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-21
Staple cartridge replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-22
Staple jam removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-24
Misfeed removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-26
7-1
SYSTEM CONFIGURATION
The options which are available for this copier are shown below.
20-bin staple sorter (AR-SS2)
Reversing automatic
document feeder (AR-RF1)
Document cover (AR-VR2)
Finisher (AR-FN4)
Duplex module
(AR-DU2N)
500-sheet paper drawer (AR-CS2N)
Large capacity tray (AR-LC2N)
The front cover is to be
transferred from the main unit.
NOTE:
Print engine power supply unit (AR-PX4)
The specifications of the 500-sheet
Fiery print controller (AR-PE2)
paper drawer (AR-CS2N) are the same
The operation manuals for the printer
as those of the paper trays in the copier.
controller are supplied with this controller.
See page 4-2.
7-2
20-BIN STAPLE SORTER (AR-SS2)
There are two sorter modes for different copying jobs: one sorts
copies into sets matching the sequence of the originals and the
second groups copies from different originals into separate sort bins.
The AR-SS2 20-Bin Staple Sorter has, in addition to the above two
modes, a STAPLE SORT mode. Sorted copies can be automatically
stapled together.
The maximum allowable number of copies varies with the selected
mode.
The number of copies will be automatically reset to the maximum
number allowable for the selected mode when copying begins if this
maximum is exceeded.
★KEY OPERATOR
In the default setting, if the number of copies
exceeds the bin capacity in the SORT or the STAPLE SORT mode, the
copying will be automatically stopped. To cancel this setting, see page 24
of the KEY OPERATOR'S GUIDE.
PART NAMES
Staple required indicator
Manual staple key
Stapler cover
Sort bins
CAUTION
●
Do not put pressure on the sorter or subject it to undue force.
●
Do not place your hands on the sorter during copying because the sorter moves up and down.
7-3
20-BIN STAPLE SORTER (AR-SS2)
Using the staple sorter
Press the OUTPUT key and select the desired mode.
SORT
GROUP
To cancel the mode, press the OUTPUT key and select “NON
SORT” on the touch panel.
READY TO COPY.
NON-SORT
OK
OUTPUT
When none of the three sorter modes, SORT, STAPLE SORT or
GROUP is selected, the copier is in the NON-SORT mode. In this
mode, all copies will be deposited in the top bin of the sorter.
Be sure to use the NON-SORT mode when copying onto special
papers such as transparency film or label stock.
STAPLE
SORT
NON SORT
SORT
GROUP
1
AUTO
AUTO
8/ 11
2
100%
EXPOSURE
PAPER SELECT
COPY RATIO
READY TO COPY.
OUTPUT
SORT
OK
Press the OUTPUT key and select the SORT mode.
STAPLE
SORT
SORT is used for automatic copy collating. Copies of each original
will be sequentially deposited in the sort bins.
NON SORT
SORT
GROUP
1
AUTO
AUTO
8/ 11
2
100%
COPY RATIO
EXPOSURE
PAPER LECT
READY TO COPY.
OUTPUT
STAPLE SORT
OK
Press the OUTPUT key and select the STAPLE SORT mode.
In this mode, copies will be automatically sorted and finished sets of
copies can be stapled with the manual staple key.
When used in conjunction with an optional RADF, sorted copies will
be automatically stapled.
STAPLE
SORT
NON SORT
SORT
GROUP
1
AUTO
AUTO
8/ 11
2
100%
EXPOSURE
PAPER SELECT
COPY RATIO
READY TO COPY.
OUTPUT
GROUP
OK
Press the OUTPUT key and select the GROUP mode.
In the GROUP mode, all copies of the same original will be
deposited in the same bin.
STAPLE
SORT
NON SORT
SORT
GROUP
1
8/ 11
2
AUTO
AUTO
10
COPY O
EXPOSURE
PAPER SELECT
7-4
20-BIN STAPLE SORTER (AR-SS2)
SORTER CAPACITY
Sort bins
Sort Mode:
Bin capacity
(max.)
Paper size
5-1/2" x 8-1/2", 8-1/2" x
11", 8-1/2" x 11"R
50
25
Top bin
8-1/2" x 13", 8-1/2" x 14",
11" x 17"
100 sheets in the NON-SORT mode
(60 sheets for 8-1/2" x 13, 8-1/2" x 14", 11" x 17", and
12" x 18" )
Staple Sort Mode:
Bin capacity
(max.)
Paper size
8-1/2" x 11", 8-1/2" x
11"R
30
25
8-1/2" x 13", 8-1/2" x 14",
11" x 17"
Group Mode:
Bin capacity
(max.)
Paper size
5-1/2" x 8-1/2", 8-1/2" x
11", 8-1/2" x 11"R
8-1/2" x 13", 8-1/2" x 14",
11" x 17"
30
25
The limits for the number of originals which can be used and the number of copies that can be set for each
paper size are as follows:
Max. No. Max. No.
Mode
NON-
Paper size
of
of copies
originals to be set
Min.: 5-1/2" x 8-1/2"
Max.: 12" x 18"
–
100
20
SORT
SORT
5-1/2" x 8-1/2", 8-1/2" x
11", 8-1/2" x 11"R
50
25
8-1/2" x 13", 8-1/2" x 14",
11" x 17"
STAPLE
SORT
8-1/2" x 11", 8-1/2" x 11"R
30
25
20
8-1/2" x 13", 8-1/2" x 14",
11" x 17"
GROUP
5-1/2" x 8-1/2", 8-1/2" x
11", 8-1/2" x 11"R
20
30
25
8-1/2" x 13", 8-1/2" x 14",
11" x 17"
NOTES:
●
When color copying is performed, much toner may be put on copy paper depending on the image. In this case,
the copies may be curled, resulting in improper stapling or improperly aligned copies.
If the specified number of copies is more than the maximum number of copies that can be set, the copy quantity
display will change to the corresponding number in the above table in the SORT, STAPLE SORT, or GROUP
mode after copying starts.
●
●
●
When making single-sided copies from two-sided originals, the maximum number of originals that can be copied
is half the number shown in the above table.
Do not use special paper in the SORT, STAPLE SORT, or GROUP mode.
7-5
20-BIN STAPLE SORTER (AR-SS2)
Staple sort
The STAPLE SORT mode staples copies of 8-1/2" x 11", 8-1/2" x
11"R, 8-1/2" x 14", and 11" x 17" sizes. For other paper sizes, use the
manual stapling mode. See page 7-8.
Using the document glass
Set the original on the document glass with the corner
to be stapled to the upper right.
Stapling position
1
●
Copy from the last page to the first page.
●
Ifthenumberofcopiestobedeliveredintoeachbinismorethan
30 for 8-1/2" x 11" or 8-1/2" x 11"R paper or 25 for 8-1/2" x 14"
or 11" x 17" paper, the copies will not be stapled.
2-SIDED
COPY
Press the OUTPUT key and select the STAPLE SORT
mode.
2
OK
●
Make sure that there is no paper in any sort bin before selecting
OUTPUT
the STAPLE SORT mode.
STAPLE
SORT
GROUP
SORT
1
AUTO
8/ 11
2
100%
COPY RATIO
PAPER SELECT
Set the number of copies.
INTE
1
4
2
5
8
3
●
3
4
5
TERRUPT
Up to 20 sets can be made.
6
9
CLE
CLEAR
ALL
CA
AL
Press the COLOR COPY START (
COPY START ( ) key.
) key or BLACK
7
C
AUDIT
PROGRAM
C
CL
PCLEAR
0
When all copies are made and sorted, press the manual
staple key.
●
Each set of copies will be stapled.
●
Sets of copies containing copies of different width will not be
stapled.
7-6
20-BIN STAPLE SORTER (AR-SS2)
Using the optional RADF
Set the originals in the document feeder tray face up
with the stapling position in the upper left corner.
Stapling position
1
2
3
4
●
Ifthenumberofcopiestobedeliveredintoeachbinismorethan
30 for 8-1/2" x 11" or 8-1/2" x 11"R paper or 25 for 8-1/2" x 14"
or 11" x 17" paper, the copies will not be stapled.
2-SIDED
COPY
Press the OUTPUT key and select the STAPLE SORT
mode.
OK
●
Make sure that there is no paper in any sort bin before selecting
OUTPUT
the STAPLE SORT mode.
STAPLE
SORT
SORT
GROUP
1
AUTO
8/ 11
2
100%
COPY RATIO
PAPER SELECT
N
Set the number of copies.
INTERRUPT
1
4
2
5
8
0
3
6
●
Up to 20 sets can be made.
CLEAR
ALL
CA
7
9
AUDIT
PROGRAM
C
CLEAR
P
Press the COLOR COPY START (
) key or BLACK
INTERRUPT
CLEAR
COPY START (
) key.
3
6
9
●
Whencopyingandsortingarecompleted, eachsetofcopieswill
be automatically stapled.
CA
ALL
●
Sets of copies containing copies of different width will not be
stapled.
PROGRAM
C
CLEAR
P
7-7
20-BIN STAPLE SORTER (AR-SS2)
Manual stapling
To use the stapling feature only, without using the STAPLE SORT
mode, follow the procedure below.
Align the edges of the copies to be stapled.
1
2
Place the set of copies into the top bin, making sure the
edges are flush with the inner right corner, as shown in
the figure.
Copies
●
Make sure that there is no paper in the other sort bins. If there
Stapling location
is, the manual staple key will not light up.
●
Upto30sheetsofpapercanbestapledtogether.Exceedingthis
maximum may result in damage to the stapler.
Press the manual staple key when it lights up.
3
●
The set of copies will be stapled.
7-8
20-BIN STAPLE SORTER (AR-SS2)
Staple cartridge replacement
When the staple cartridge becomes empty, the message “ADD
STAPLES.” will appear. Replace the staple cartridge as follows:
Open the stapler cover.
1
2
3
4
Lift the release lever and pull out the staple box.
●
Lift the release lever to unlock the staple box. Then pull out the
box.
Remove the empty staple cartridge from inside the
staple box.
Insertthenewstaplecartridgeintotheboxuntilitclicks
in place.
●
Insert the new cartridge by aligning the arrows on the cartridge
with those on the box. Check that the cartridge locks in place by
pulling it slightly.
●
The cartridge holds 5,000 staples.
NOTE:
Be sure not to remove the rear paper and tape before inserting
the cartridge.
7-9
20-BIN STAPLE SORTER (AR-SS2)
Remove the rear paper and tape from the cartridge.
●
5
Pull them straight. If they are pulled obliquely, the tape may be
torn.
Insert the staple box into the stapler until it clicks in
place.
6
7
Close the stapler cover.
Placeasheetofpaperintothetopbin.Pressthemanual
staple (
) key on the staple sorter when it lights up.
8
●
●
●
Check to see whether the sheet is stapled.
If it is not stapled, press the manual staple key again.
If the stapler does not operate properly even after
replacement, a staple may be jammed in it. See next page.
Staples for the staple sorter are available from your Sharp
dealer.
7-10
20-BIN STAPLE SORTER (AR-SS2)
Staple jam removal
If staples become jammed in the stapler, the message “CHECK
STAPLER POSITION OR STAPLE JAM.” will appear. Remove the
jammed staples in the manner described below:
Open the stapler cover.
1
2
3
4
Lift the release lever and pull out the staple box.
●
Lift the release lever to unlock the staple box. Then pull out the
box.
Lower the lever at the end of the staple box and remove
the jammed staples.
Return the lever to its original position.
7-11
20-BIN STAPLE SORTER (AR-SS2)
Insert the staple box into the stapler unit until it clicks in
place.
5
6
7
Close the stapler cover.
Following the stapling procedure on page 7-8, staple a
copy to check that the stapler works properly.
●
If it does not, repeat this procedure until it does.
7-12
20-BIN STAPLE SORTER (AR-SS2)
Misfeed removal
The copier will stop when a misfeed occurs.
The message “MISFEED HAS OCCURRED. CLEAR INDICATED
AREA. PRESS FOR RECOVERY INSTRUCTIONS.” will appear
MISFEED HAS OCCURRED.
with a display of paper misfeed locations. Press the INFORMATION
key for more detailed information as necessary.
CLEAR INDICATED AREA.
PRESS FOR RECOVERY INSTRUCTIONS.
Push the sorter release button and slide the sorter
carefully along the guides away from the copier.
1
Remove the misfed paper from the sorter or from the
exit area of the copier.
2
Slide the sorter back toward the copier and latch it into
place.
3
●
Confirm that the misfeed display is cleared.
●
If the message indicating a misfeed is still displayed, check the
inside of the copier and remove any remaining misfed paper.
7-13
20-BIN STAPLE SORTER (AR-SS2)
Specifications
No. of bins
Paper size
20
Max. 12" x 18"
Min. 5-1/2" x 8-1/2"
Stapling capacity
Power supply
Weight*
30 sheets (28 lbs.)
Drawn from the copier
Approx. 58.2 lbs. (26.4kg)
*with mounting kit
Dimensions
16-37/64" (W) x 23-25/64" (D) x 24-37/64" (H)
(421 mm (W) x 594 mm (D) x 624 mm (H))
Bin capacity
Bin
Top Bin
Top Bin and Other Bins
SORT GROUP
Mode
NON-SORT
STAPLE SORT
Paper Weight
13 ~ 28 lbs. 28+ ~ 75 lbs. 17 ~ 28 lbs.* 17 ~ 28 lbs.
17 ~ 28 lbs.*
25
8-1/2" x 13",
8-1/2" x 14",
11" x 17"
60
10
25
25
12" x 18"
60
10
10
-
-
-
8-1/2" x 11",
8-1/2" x 11R"
100
50
30
30
5-1/2" x 8-1/2"
100
100
10
10
50
-
30
-
-
-
7-1/4" x
10-1/2"R
* In the COVERS mode, 2 sheets of 75 lb, paper can be fed for each set from by-pass.
If the stapler capacity limits are exceeded, stapling jams, poorly stapler sets or damage may
occur to the stapler.
Use SHARP recommened paper for best performance.
Specifications are subject to change for improvement without notice.
7-14
LARGE CAPACITYTRAY (AR-LC2N)
The large capacity tray provides the added convenience of having
3,000 additional sheets of 8-1/2" x 11" paper available.
PART NAMES
Paper tray control button
Specifications
Paper size
Paper weight
Paper capacity
Weight
8-1/2" x 11"
15 lbs. to 28 lbs.
3,000 sheets (20 lbs.)
Approx. 70.6 lbs. (32 kg)
Dimensions
13" (W) x 21-17/64" (D) x 23-7/16" (H)
(330 mm (W) x 540 mm (D) x 595 mm (H))
Specifications are subject to change for improvement without notice.
7-15
LARGE CAPACITY TRAY (AR-LC2N)
Loading copy paper
The large capacity tray will automatically lower when the tray runs out
of paper.
Pressthepapertraycontrolbuttononthelargecapacity
tray.
1
●
The button lamp will blink while the feed table is lowering and
will go out when the tray is ready to be opened.
When the button lamp goes out, pull the paper tray out.
2
3
●
Do not pull the paper tray out before the button lamp goes out.
Fan the copy paper.
Load the paper onto the feed table.
Maximum height line
4
5
●
Be sure to load paper appropriate for the large capacity tray.
See page 7-15.
●
Do not exceed the maximum height line.
Gently push the large capacity tray back into place.
●
The paper tray control button lamp will blink as the feed table
returns to the feed position and will light up steadily when it is in
position to feed.
7-16
LARGE CAPACITY TRAY (AR-LC2N)
Misfeed removal
The copier will stop when a misfeed occurs.
MISFEED HAS OCCURRED.
The message “MISFEED HAS OCCURRED. CLEAR INDICATED
AREA.PRESS FORRECOVERYINSTRUCTIONS.”willappearwith
adisplayofpapermisfeedlocations. PresstheINFORMATIONkeyfor
more detailed information as necessary.
CLEAR INDICATED AREA.
PRESS
FOR RECOVERY INSTRUCTIONS.
While holding the tray release lever, carefully slide the
large capacity tray away from the copier until it stops.
Release lever
1
Remove any misfed paper from the copier and the large
capacity tray.
Upper right
side cover
2
●
Be sure not to tear the misfed paper during removal.
●
Open and close the upper right side cover of the copier after
removing the misfed paper from the copier.
If the misfed paper cannot be removed easily, open the upper
right side cover to remove the paper.
7-17
LARGE CAPACITY TRAY (AR-LC2N)
Push the large capacity tray toward the copier and latch
it into place.
3
4
5
6
If misfed paper is not found in step 2, pull the tray out.
●
Whenpullingthelargecapacitytrayout,besuretopullitoutafter
the paper tray control button lamp goes out.
Remove the misfed paper.
Gently push the tray back into place.
●
Confirm that the misfeed display is cleared.
7-18
FINISHER (AR-FN4)
The AR-FN4 finisher provides an offset stack mode of the output for
both copying and printing. A staple print mode is provided for the print
mode only and will not function in the copy mode.
PART NAMES
Offset tray
Finisher release lever
Staple cartridge
Pull out the tray extension
when 8-1/2" x 14" or
larger paper is to be output.
Specifications
Paper
capacity/size paper
(16~28 lbs.)
Ordinary
Face-up
Non offset: 1,000 sheets 5-1/2" x 8-1/2", 5-1/2" x 8-1/2"R, 8-1/2" x 11",
8-1/2" x 11"R, 7-1/4" x 10-1/2"R
700 sheets 8-1/2" x 13", 8-1/2" x 14"
500 sheets 11" x 17", 12" x 18"
Offset:
1,000 sheets 5-1/2" x 8-1/2", 8-1/2" x 11", 8-1/2" x 11"R
700 sheets 8-1/2" x 13", 8-1/2" x 14"
500 sheets 11" x 17"
Face-down
(*For printer
use)
Non offset: 1,000 sheets 5-1/2" x 8-1/2", 5-1/2" x 8-1/2"R, 8-1/2" x 11",
8-1/2" x 11"R, 7-1/4" x 10-1/2"R
700 sheets 8-1/2" x 13", 8-1/2" x 14"
500 sheets 11" x 17", 12" x 18"
Offset:
1,000 sheets 5-1/2" x 8-1/2", 8-1/2" x 11", 8-1/2" x 11"R
700 sheets 8-1/2" x 13", 8-1/2" x 14"
500 sheets 11" x 17"
Heavy paper*
(*Transparency
film)
Face-up
Face-up
Non offset: 10 sheets
8-1/2" x 11", 8-1/2" x 11"R, 11" x 17"
Paper weight
Offset
16-75 lbs.
17-34 lbs.
Face-down
(*For printer
use)
0.8 inches (20 mm)
Paper size for stapling
(*For printer use)
5-1/2" x 8-1/2", 8-1/2" x 11", 8-1/2" x 11"R, 8-1/2" x 13", 8-1/2" x 14",
11" x 17"
Stapling capacity*
20 sheets 5-1/2" x 8-1/2", 8-1/2" x 11", 8-1/2" x 11"R, 8-1/2" x 13",
(*For printer use /for 28 lbs. paper)
8-1/2" x 14"
15 sheets 11" x 17"
Power supply
Weight
24V, 2.5A
Max. 6.5A (drawn from the copier)
Approx. 30.9 lbs. (14kg) *without mounting kit
Dimensions
20.3"(W) x 22.6"(D) x 15.0"(H) *without mounting kit
(515mm(W) x 574mm(D) x 381mm(H))
Specifications are subject to change for improvement without notice.
7-19
FINISHER (AR-FN4)
Offset stack
In the initial settings, the offset stack function is set to off. To enable
the offset stack function, press the “OUTPUT” key and then touch the
“OFFSET” icon on the touch panel. To disable the “OFFSET”
function, press the “OUTPUT” key and then touch the “NON
OFFSET” icon. When the offset function is selected, the output tray
will move side to side each time a set is output so that each set is
offset by approximately 0.8 inches (20 mm) from the previous set.
NOTE:
Some type or quality of paper might cause tight curl when it is output.
In this case, remove the paper out of the paper tray or the bypass tray
and reload it upside down.
OFFSET mode
When making copies, the output tray will shift from its
READY TO COPY.
OUTPUT
previous position by approximately 0.8 inches (20 mm)
each time a “START” key is pressed. In this way, the set in
progress will be offset from the previous set. Copies in the
size of 5-1/2" x 8-1/2", 8-1/2" x 11", 8-1/2" x 11"R, 8-1/2" x
13", 8-1/2" x 14" and 11"x 17" can be offset.
OK
NON OFFSET
OFFSET
1
8/ 11
2
AUTO
AUTO
10
COPY IO
EXPOSURE
PAPER SELECT
NON OFFSET mode
All copies will be aligned in one stack in the tray with no
offset.
READY TO COPY.
OUTPUT
OK
NON OFFSET
OFFSET
1
AUTO
AUTO
100%
COPY RATIO
EXPOSURE
PAPER SE
7-20
FINISHER (AR-FN4)
(*In the PRINT mode only)
Staple print*
The staple print mode can be selected for stapling printed sets in the
size of 5-1/2" x 8-1/2", 8-1/2" x 11", 8-1/2" x 11"R, 8-1/2" x 13", 8-1/2"
x 14", and 11" x 17".
NOTE:
In the COPY mode, which delivers the paper face up, this function is
not available.
Check the operation panel to confirm that the ONLINE
indicator is lit. If not lit, press the “PRINT” key to enter
the print mode and then press the ONLINE key on the
touch panel.
1
2
3
4
DATA ON LINE
PRINT
●
An optional power supply kit (AR-PX4) and an optional printer
controller (AR-PE2) are needed for the printing from computer.
COPY
Check the paper tray(s) to ensure that the desired paper
is loaded.
READY TO PRINT.
●
Themaximumnumberofsheetsforstaplingis20forpaperinthe
1
82 11R
size of 5-1/2" x 8-1/2", 8-1/2" x 11", 8-1/2" x 11"R, 8-1/2" x 13",
or 8-1/2" x 14" paper and 15 for 11" x 17" paper. If the maximum
is exceeded, the sheets will not be stapled.
1
1.
82 11
2.
11 17
1
3.
82 14
●
Ensure that no paper remains in the output tray. Stapling will not
ONLINE
be done if paper remains at the start of the print job.
PAPER SELECT
OFFLINE
Make all print selections by the printer driver at your
computer and give the print command.
●
Refertothedocumentationforthecomputerand/ortheapplication
software for help on issuing the necessary commands.
The printed output will be stapled.
●
The printed sets will be delivered face down with one staple in
their top left edge.
7-21
FINISHER (AR-FN4)
Staple cartridge replacement
When the staple cartridge is empty, the message “SLIDE THE
FINISHER AWAY FROM THE COPIER AND ADD STAPLES.” will
appear.
Replace the staple as follows:
Whileholdingthefinisherreleaselever,slidethefinisher
away from the copier.
1
2
Pull out the staple box.
●
Topreventbumpingorscrapingyourhandduringremovalofthe
staple box, proceed as shown in the illustration and as follows:
Graspthestapleboxwithyourthumbandindexfinger,andplace
the heel of your hand against the finisher frame as shown with
arrow
1
in the illustration.
2
Remove the staple box in the direction of the arrow
by
squeezingwithyourfingersandrotatingagainsttheheelofyour
hand.
Remove the empty staple cartridge from inside the
staple box.
3
4
Insert the new staple cartridge into the box until it clicks
in place.
●
Insert the new cartridge by aligning the arrows on the cartridge
with those on the box. Check that the cartridge locks in place by
pulling it slightly.
●
The cartridge holds 3,000 staples.
NOTE:
Be sure to remove the rear paper and tape before inserting the
cartridge.
7-22
FINISHER (AR-FN4)
Remove the rear paper and tape from the cartridge.
5
6
7
●
Pull them straight. If they are pulled obliquely, the tape may be
torn.
Insert the staple box into the stapler until it clicks in
place.
Push the finisher toward the copier and latch it in place.
●
If the stapler does not work properly after cartridge installation,
it may have a jammed staple in it. See next page.
●
Staples for the finisher are available from your Sharp dealer.
CAUTION
Use caution while latching the finisher into place.
To prevent pinching your fingers, do not place your hand or fingers
on the release lever while moving the finisher toward the copier.
7-23
FINISHER (AR-FN4)
Staple jam removal
If staples become jammed in the stapler, the message “CHECK
STAPLER POSITION OR STAPLE JAM” will appear. Remove the
jammed staples in the manner described below:
Whileholdingthefinisherreleaselever,slidethefinisher
away from the copier.
1
2
Pull out the staple box.
●
Topreventbumpingorscrapingyourhandduringremovalofthe
staple box, proceed as shown in the illustration and as follows:
Graspthestapleboxwithyourthumbandindexfinger,andplace
the heel of your hand against the finisher frame as shown with
1
arrow
in the illustration.
2
Remove the staple box in the direction of arrow by squeezing
with your fingers and rotating against the heel of your hand.
Lower the lever at the end of the staple box and remove
the jammed staples.
3
4
Return the lever to its original position.
7-24
FINISHER (AR-FN4)
Insert the staple box into the stapler unit until it clicks in
place.
5
6
Push the finisher toward the copier and latch it in place.
CAUTION
Use caution while latching the finisher into place.
To prevent pinching your fingers, do not place your hand or fingers
on the release lever while moving the finisher toward the copier.
7-25
FINISHER (AR-FN4)
Misfeed removal
MISFEED HAS OCCURRED.
The copier will stop when a misfeed occurs.
The message “MISFEED HAS OCCURRED. CLEAR INDICATED
AREA. PRESS
FOR RECOVERY INSTRUCTIONS.” will appear
with a display of paper misfeed locations. Press the INFORMATION
(
) key for more detailed information as necessary.
CLEAR INDICATED AREA.
PRESS
FOR RECOVERY INSTRUCTIONS.
Whileholdingthefinisherreleaselever,slidethefinisher
away from the copier.
1
2
Remove the misfed paper from the finisher or from the
exit area of the copier.
Misfeed in the finisher
When a misfeed occurs in the finisher, turn the roller rotating knob in
the direction of arrow. The misfed paper will be delivered to the offset
tray.Ifthepaperisnotdeliveredtotheoffsettray,openthepaperguide
as shown and remove the paper.
7-26
FINISHER (AR-FN4)
Misfeed in the exit area of the copier
When misfed paper is lodged in the fusing roller of the copier and can
not be pulled out, open the front cover of the copier and turn the roller
rotating knob in the direction of arrow to remove the misfed paper.
Push the finisher toward the copier and latch it in place.
3
●
Confirm that the misfeed display is cleared.
●
If the message indicating a misfeed is still displayed, check the
inside of the copier and remove any remaining misfed paper.
CAUTION
Use caution while latching the finisher into place.
To prevent pinching your fingers, do not place your hand or fingers
on the release lever while moving the finisher toward the copier.
7-27
WARNING:
FCC Regulations state that any unauthorized changes or modifications to
this equipment not expressly approved by the manufacturer could void the
user's authority to operate this equipment.
Note:
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the operation manual, may cause
harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
NOTICE
BE SURE TO ASK YOUR AUTHORIZED SHARP DEALER ABOUT THE
WARRANTY THAT YOUR SELLING DEALER EXTENDS TO YOU. In order to
assure you, the end-user, of warranty protection, Sharp extends a limited
warranty to each of its authorized dealers and, in turn, requires each of its
authorized dealers to extend its own warranty to you on terms that are no less
favorable than those given to the dealer by Sharp. You should be aware,
however, that Sharp does not itself extend any warranties, either express or
implied, directly to you, the end-user and no one is authorized to make any
representations or warranties on behalf of Sharp. Specifically, SHARP DOES
NOT EXTEND TO YOU, THE END-USER, ANY EXPRESS WARRANTY OR
ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR USE OR
FITNESS FOR ANY PARTICULAR PURPOSE IN CONNECTION WITH THE
HARDWARE, SOFTWARE OR FIRMWARE EMBODIED IN, OR USED IN
CONJUNCTION WITH THIS PRODUCT. Sharp is not responsible for any
damages or loss, either direct, incidental or consequential, which you, the end-
user, may experience as a result of your purchase or use of the hardware,
software or firmware embodied in or used in conjunction with this Product. Your
sole remedy, in the event that you encounter any difficulties with this Product, is
against the authorized dealer from which you purchased the Product.
In the event that this authorized dealer does not honor its warranty
commitments, please contact the General Manager , Business Products Group,
Sharp Electronics Corporation, Sharp Plaza, Mahwah, NJ 07430-2135, so that
Sharp can try to help assure complete satisfaction of all the warranty rights to
which you are entitled from the authorized dealer.
AR-C160
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-2135.
SHARP CORPORATION
PRINTED IN JAPAN
2001E
KS1
TINSE2098FCZZ
|