Z11PA-D8C Series
User Guide
Contents
Notices ..................................................................................................................... viii
Federal Communications Commission Statement........................................viii
Canadian Department of Communications Statement..................................viii
REACH .....................................................................................................viii
Safety information...................................................................................................... ix
Electrical safety...............................................................................................ix
Operation safety..............................................................................................ix
Australia statement notice............................................................................... x
How this guide is organized............................................................................xi
Where to find more information.......................................................................xi
Z11PA-D8C Series specifications summary.......................................................... xiii
Welcome!....................................................................................................1-2
Package contents.......................................................................................1-2
Serial number label....................................................................................1-3
Special features..........................................................................................1-3
Before you proceed ...................................................................................2-2
Motherboard overview...............................................................................2-3
System memory .........................................................................................2-8
iii
Contents
Expansion slots........................................................................................2-11
Jumpers....................................................................................................2-14
Onboard LEDs..........................................................................................2-20
Connectors...............................................................................................2-24
Starting up for the first time......................................................................3-2
Powering off the computer........................................................................3-3
BIOS setup program..................................................................................4-6
Main menu ..................................................................................................4-9
iv
Contents
Advanced menu .......................................................................................4-11
Event Logs menu.....................................................................................4-37
Server Mgmt menu...................................................................................4-38
Security menu ..........................................................................................4-39
Boot menu ................................................................................................4-41
Tool menu.................................................................................................4-42
Save & Exit menu.....................................................................................4-42
v
Contents
RAID driver installation .............................................................................6-2
VGA driver installation ............................................................................6-13
Z11PA-D8C Series block diagram ......................................................................... A-2
Q-Code table............................................................................................................ A-3
Simplified EU Declaration of Conformity.............................................................. A-5
vii
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
•
•
This device may not cause harmful interference, and
This device must accept any interference received including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with manufacturer’s instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver
is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is required
to assure compliance with FCC regulations. Changes or modifications to this unit not
expressly approved by the party responsible for compliance could void the user’s authority
to operate this equipment.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus set out in the Radio Interference Regulations of the Canadian Department
of Communications.
This class B digital apparatus complies with Canadian ICES-003.
REACH
Complying with the REACH (Registration, Evaluation, Authorization, and Restriction of
Chemicals) regulatory framework, we publish the chemical substances in our products at
ASUS REACH website at http://csr.asus.com/english/REACH.htm.
viii
Safety information
Electrical safety
•
To prevent electrical shock hazard, disconnect the power cable from the electrical outlet
before relocating the system.
•
When adding or removing devices to or from the system, ensure that the power cables
for the devices are unplugged before the signal cables are connected. If possible,
disconnect all power cables from the existing system before you add a device.
•
•
•
Before connecting or removing signal cables from the motherboard, ensure that all
power cables are unplugged.
Seek professional assistance before using an adapter or extension cord. These devices
could interrupt the grounding circuit.
Make sure that your power supply is set to the correct voltage in your area. If you are
not sure about the voltage of the electrical outlet you are using, contact your local power
company.
•
If the power supply is broken, do not try to fix it by yourself. Contact a qualified service
technician or your retailer.
Operation safety
•
•
•
•
Before installing the motherboard and adding devices on it, carefully read all the manuals
that came with the package.
Before using the product, make sure all cables are correctly connected and the power
cables are not damaged. If you detect any damage, contact your dealer immediately.
To avoid short circuits, keep paper clips, screws, and staples away from connectors,
slots, sockets and circuitry.
Avoid dust, humidity, and temperature extremes. Do not place the product in any area
where it may become wet.
•
•
Place the product on a stable surface.
If you encounter technical problems with the product, contact a qualified service
technician or your retailer.
DO NOT throw the motherboard in municipal waste. This product has been designed to
enable proper reuse of parts and recycling. This symbol of the crossed out wheeled bin
indicates that the product (electrical and electronic equipment) should not be placed in
municipal waste. Check local regulations for disposal of electronic products.
DO NOT throw the mercury-containing button cell battery in municipal waste. This symbol
of the crossed out wheeled bin indicates that the battery should not be placed in municipal
waste.
ix
Australia statement notice
From 1 January 2012 updated warranties apply to all ASUS products, consistent with the
Australian Consumer Law. For the latest product warranty details please visit
https://www.asus.com/support. Our goods come with guarantees that cannot be excluded
under the Australian Consumer Law. You are entitled to a replacement or refund for a major
failure and compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality
and the failure does not amount to a major failure.
If you require assistance please call ASUS Customer Service 1300 2787 88 or visit us at
https://www.asus.com/support.
x
About this guide
This user guide contains the information you need when installing and configuring the
motherboard.
How this guide is organized
This user guide contains the following parts:
•
Chapter 1: Product Introduction
This chapter describes the features of the motherboard and the new technologies it
supports.
•
Chapter 2: Hardware Information
This chapter lists the hardware setup procedures that you have to perform when
installing system components. It includes description of the switches, jumpers, and
connectors on the motherboard.
•
•
Chapter 3: Powering Up
This chapter describes the power up sequence and ways of shutting down the system.
Chapter 4: BIOS Setup
This chapter tells how to change system settings through the BIOS Setup menus.
Detailed descriptions of the BIOS parameters are also provided.
•
•
Chapter 5: RAID Configuration
This chapter provides instructions for setting up, creating, and configuring RAID sets
using the available utilities.
Chapter 6: Driver Installation
This chapter provides instructions for installing the necessary drivers for different
system components.
•
Appendix: Reference Information
This appendix includes additional information that you may refer to when configuring
the motherboard.
Where to find more information
Refer to the following sources for additional information and for product and software
updates.
1.
ASUS websites
The ASUS website provides updated information on ASUS hardware and software
products. Refer to the ASUS contact information.
2.
Optional documentation
Your product package may include optional documentation, such as warranty flyers,
that may have been added by your dealer. These documents are not part of the
standard package.
xi
Conventions used in this guide
To ensure that you perform certain tasks properly, take note of the following symbols used
throughout this manual.
DANGER/WARNING: Information to prevent injury to yourself when trying to
complete a task.
CAUTION: Information to prevent damage to the components when trying to
complete a task.
IMPORTANT: Instructions that you MUST follow to complete a task.
NOTE: Tips and additional information to help you complete a task.
Typography
Bold text
Italics
Indicates a menu or an item to select.
Used to emphasize a word or a phrase.
<Key>
Keys enclosed in the less-than and greater-than sign means
that you must press the enclosed key.
Example: <Enter> means that you must press the Enter or
Return key.
<Key1> + <Key2> + <Key3> If you must press two or more keys simultaneously, the key
names are linked with a plus sign (+).
Example: <Ctrl> + <Alt> + <Del>
Means that you must type the command exactly as shown,
then supply the required item or value enclosed in brackets.
Command
Example: At DOS prompt, type the command line:
format A:/S
xii
Z11PA-D8C Series specifications summary
Model Name
Z11PA-D8C
2 x 140W Socket P (LGA 3647)
1st Gen Intel® Xeon® Processor Scalable Family
2nd Gen Intel® Xeon® Processor Scalable Family
Intel® Lewisburg PCH (C621)
Processor Support /
System Bus
Core Logic
CEB
Form Factor
Fan Speed
Control
Rack Optimized
(Dedicated for
rack)
ASUS
Features
ASUS Control
Center
Total Slots
Voltage
8 (4-channel per CPU, 4 DIMM per CPU)
1.2V
Capacity
Maximum up to 4096GB
DDR4 2933* (1 DIMM per Channel)
DDR4 2666/2400/2133 RDIMM/LRDIMM/LRDIMM 3DS
(2 DIMM per Channel)
Intel® Optane™ DC persistent memory (DCPMM)
Memory Type
Memory
*
2933MHz will drop to 2666MHz when using 2DPC configurations
** Refer to ASUS server AVL for the latest update
4GB, 8GB, 16GB, 32GB (RDIMM)
32GB, 64GB, 128GB (LRDIMM)
64GB, 128GB (3DS)
Memory Size
128GB, 256GB, 512GB (DCPMM)
Total PCI/ PCI-X
/ PCI-E Slots
3
Slot Location 1
Slot Location 2
Slot Location 3
Slot Location 4
Slot Location 5
Slot Location 6
Slot Location 7
Additional Slot 1
Additional Slot 2
PCI-E x8 (Gen3 x8 link) from CPU2
-
Expansion
Slots (follow
SSI Location
number)
PCI-E x16 (Gen3 x16 link) from CPU1
-
PCI-E x16 (Gen3 x16 Link) from CPU1
-
-
-
-
2 x Intel I210AT
1 x Management Port
Aspeed AST2500 64MB
LAN
Networking
Graphic
VGA
(continued on the next page)
xiii
Z11PA-D8C Series specifications summary
Model Name
Z11PA-D8C
Intel® Lewisburg PCH
SATA Controller
- 8 x SATA3 6Gb/s ports (8 by 2 mini-SAS Connector) + 1 x M.2
connector (SATA 6Gb/s & PCI-E Gen3 x4 link)
Optional kits:
Storage
SAS Controller
ASUS PIKE II 3008 8-port SAS 12G HW RAID card
ASUS PIKE II 3108 8-port SAS 12G HW RAID card
TPM Header
1
PSU Connector
24-pin SSI power connector + 2 x 8-pin SSI 12V
Management
Connector
Onboard ASMB9-iKVM
Fan Header
8 x 4 pin
SMBus
1
Onboard I/O
Chassis Intruder
Front LAN LED
Serial Port Header
M.2 Connector
Micro SD card
VROC Key Header
External USB Port
VGA Port
1
Connectors
2
1
1 (NGFF Type 22110)
1
1
4 x USB 3.0
1
Rear I/O
2 x GbE LAN
Connectors
RJ-45
1 x Mgmt LAN
Out of Band
Remote
Management
Management
Solution
ASMB9-iKVM for KVM-over-Internet
CPU Temperature
Monitoring
FAN RPM
Operating temperature: 10°C ~ 35°C
Non operating temperature: -40°C ~ 70°C
Non operating humidity: 20% ~ 90% (Non condensing)
Environment
* Specifications are subject to change without notice.
** Refer to www.asus.com for the complete list of supported PIKE cards.
xiv
1.1
Welcome!
Congratulations and thank you for buying an ASUS® Z11PA-D8C Series motherboard!
The motherboard delivers a host of new features and latest technologies, making it another
standout in the long line of ASUS quality motherboards!
Before you start installing the motherboard and hardware devices on it, check the items in
your package with the list below.
1.2
Package contents
Check your motherboard package for the following items.
Standard Gift Box Pack Standard Bulk Pack
I/O Shield
1
1
Support DVD
Application CD
1
1 piece per carton
10 pieces per carton
Packaging Quantity
1 piece per carton
If any of the above items is damaged or missing, contact your retailer.
Optional items
Description
LSI 8-port SAS 12G RAID card
PIKE 3008
PIKE 3108
LSI 8-port SAS 12G HW RAID card
ASMB9-iKVM
PEM-FDR
Remote management solution provides KVM over IP solution
Mellanox ConnectX-3 FDR card
PEB-10G/57840-2S
PEB-10G/57811-1S
PEI-10G/82599-2S
Dual port 10G SFP+ Ethernet Adapter
Single port 10G SFP+ Ethernet Adapter
10GbE SFP+ Network Adapter
The ASUS PIKE 3008, PIKE 3108, and PEM-FDR cards must be installed on PCI-E slot
2/3/4/5.
1-2
Chapter 1: Product Introduction
1.3
Serial number label
Before requesting support from the ASUS Technical Support team, you must take note of
the motherboard's serial number containing 12 characters xxS2xxxxxxxx shown in the figure
below. With the correct serial number of the product, ASUS Technical Support team members
can then offer a quicker and satisfying solution to your problems.
Z11PA-D8C Series
Made
in
China
合格
xxS2xxxxxxxx
1.4
Special features
Product highlights
1.4.1
Latest Processor Technology
The motherboard supports Intel® Xeon® Scalable processor family which provides compelling
IPC increases for legacy performance improvements, floating point improvement, easier
multi-core programming, and with next-generation processor power management. Intel®
Xeon® Scalable processor family also improve the I/O capabilities and support UPI link speed
of up to 10.4GT/s.
Intel® AVX 512
Intel® AVX 2.0 extends 512-bit vector support for integer vector operations, doubles
fixed point arithmetic throughput, adds support for new vector gather, permutes/blend,
vector shifts resulting in fixed and floating-point algorithm improvements. Also, Intel's new
microarchitecture doubles the cache bandwidth at L1/L2 to support higher FLOPS and
contributes to greater performance in signal and image processing applications.
Next Generation of processor power management
Intel® Xeon® Scalable processor family enhances the processor power management with the
features of Energy Efficient Turbo, Uncore Frequency Scaling, and Per-Core P-state. Also,
the Integrated Voltage Regulator enables generational performance and power improvements
that the standard VR solutions cannot provide.
DDR4 memory support
The motherboard supports DDR4 memory that features faster clock frequencies and higher
data transfer rates of 2133 MT/s to 2666 MT/s (million transfers per second). DDR4 offers a
lower voltage standard of 1.2V that reduces memory power demand and provides improved
performance.
1-3
Z11PA-D8C Series
M.2 Support
This motherboard features the M.2 slot, which shares bandwidth with the SATA 6Gb/s port
and PCI-E Gen3 x4 and is dedicated to the operating system.
PCI Express 3.0
PCI Express 3.0 (PCIe 3.0) is the PCI Express bus standard that provides twice the
performance and speed of PCIe 2.0. It provides an optimal graphics performance,
unprecedented data speed, and seamless transition with its complete backward compatibility
to PCIe 2.0 devices.
Intel® I210AT LAN Solution
The motherboard comes with four Gigabit LAN controllers and ports which provide a total
solution for your networking needs. The onboard Intel® I210AT Gigabit LAN controllers use
the PCI Express interface and could achieve network throughput close to Gigabit bandwidth.
Intel® C621 Series Chipset
The Intel® C621 series chipset supports with enterprise class features which is targeted for
Cloud and Storage applications. It is optimized and validated to work with the latest Intel®
Xeon® Scalable processor family, compared with the last generation, it also reduces the TDP,
supports USB 3.0 with up to 12 SATA III ports thus bringing more features and benefits to the
target users.
Serial ATA III technology
The motherboard supports the Serial ATA III technology through the Serial ATA interface
and Intel® 621 chipset, delivering up to 6 Gb/s data transfer rates. It also provides enhanced
scalability, faster data retrieval, and double the bandwidth of current bus systems.
Temperature, fan, and voltage monitoring
The CPU temperature is monitored to prevent overheating and damage. The system fan
rotations per minute (RPM) is monitored for timely failure detection. The chip monitors the
voltage levels to ensure a stable supply of current for critical components.
1.4.2
Innovative ASUS features
ASUS Fan Speed control technology
The ASUS Fan Speed control technology smartly adjusts the fan speeds according to the
system loading to ensure a quiet, cool, and efficient operation.
1-4
Chapter 1: Product Introduction
2.1
Before you proceed
Take note of the following precautions before you install any motherboard component or
change any motherboard settings.
•
•
Unplug the power cord from the wall socket before touching any component.
Use a grounded wrist strap or touch a safely grounded object or a metal object, such
as the power supply case, before handling components to avoid damaging them due
to static electricity.
•
•
Hold components by the edges to avoid touching the ICs on them.
Whenever you uninstall any component, place it on a grounded antistatic pad or in the
bag that came with the component.
•
Before you install or remove any component, ensure that the power supply is switched
off or the power cord is detached from the power supply. Failure to do so may cause
severe damage to the motherboard, peripherals, and/or components.
2-2
Chapter 2: Hardware Information
2.2
Motherboard overview
Before you install the motherboard, study the configuration of your chassis to ensure that the
motherboard fits into it.
To optimize the features of your motherboard, we highly recommend that you install it in an
ATX 2.2 compliant chassis.
Ensure to unplug the chassis power cord before installing or removing the motherboard.
Failure to do so can cause you physical injury and damage motherboard components!
2.2.1
Placement direction
When installing the motherboard, ensure that you place it into the chassis in the correct
orientation. The edge with external ports goes to the rear part of the chassis as indicated in
the image below.
2.2.2
Screw holes
Place nine (9) screws into the holes indicated by circles to secure the motherboard to the
chassis.
DO NOT overtighten the screws! Doing so can damage the motherboard.
Place this side towards
the rear of the chassis
2-3
Z11PA-D8C Series
Layout contents
Internal connectors / Sockets / Jumpers / LEDs
Page
1. DDR4 DIMM sockets
2-8
2. CPU, front, and rear fan connectors (4-pin CPU_FAN1-2; FRNT_FAN1-4;
2-28
REAR_FAN1-2)
3. Power Supply SMBus connector (5-pin PSUSMB1)
4. PMBus 1.2 PSU select jumper (3-pin SMART_PSU1)
5. EATX power connectors (24-pin EATXPWR1; 8-pin EATX12V1-2)
6. CPU socket
2-26
2-17
2-30
2-6
7. Mini-SAS HD connector (ISATA1-2)
2-25
2-34
2-29
2-33
2-35
2-31
8. VPP_I2C1 connector (10-1 pin VPP_I2C1)
9. VROC KEY connector (4-pin VROC_KEY1)
10. Chassis Intrusion (2-pin INTRUSION1)
11. LAN Activity LED connector (5-1 pin LAN34_LED1)
12. System panel connector (20-1 pin PANEL1)
13. Auxiliary panel connector (20-2 pin AUX_PANEL1, 20-1 pin AUX_PANEL2) 2-32
14. USB 3.0 connector (20-1 pin USB3_12)
2-27
15. Baseboard Management Controller setting (3-pin BMC_EN1)
2-18
2-15
2-19
2-16
2-34
2-27
2-16
2-29
2-18
2-17
2-14
2-23
2-33
2-28
2-15
2-25
2-26
16. VGA controller setting (3-pin VGA_SW1)
17. PCH_MFG1 setting (3-pin PCH_MFG1)
18. ME firmware force recovery setting (3-pin ME_RCVR1)
19. System Management Bus (SMBUS) connector (5-1 pin SMBUS1)
20. USB 2.0 connector (10-1 pin USB78)
21. DDR4 thermal event setting (3-pin DIMMTRIP1-2)
22. Trusted Platform Module connector (14-1 pin TPM1)
23. IPMI SW setting (3-pin IPMI_SW1)
24. DMLAN setting (3-pin DM_IP_EN1)
25. Clear RTC RAM (3-pin CLRTC1)
26. Q-Code LEDs (PORT80_LED1)
27. Hard disk activity LED connector (4-pin HDLED1)
28. Serial port connector (10-1 pin COM1)
29. LAN controller setting (3-pin LAN_SW1-4)
30. Micro SD card slot (MSD1)
31. M.2 (NGFF) connector (NGFF1)
2-5
Z11PA-D8C Series
2.3
Central Processing Unit (CPU)
The motherboard comes with a surface mount LGA 3647 socket designed for the Intel®
Xeon® Processor Scalable Family Series.
•
Upon purchase of the motherboard, ensure that the PnP cap is on the socket and
the socket contacts are not bent. Contact your retailer immediately if the PnP cap
is missing, or if you see any damage to the PnP cap/socket contacts/motherboard
components. ASUS will shoulder the cost of repair only if the damage is shipment/
transit-related.
•
•
Keep the cap after installing the motherboard. ASUS will process Return Merchandise
Authorization (RMA) requests only if the motherboard comes with the cap on the LGA
3647 socket.
The product warranty does not cover damage to the socket contacts resulting from
incorrect CPU installation/removal, or misplacement/loss/incorrect removal of the PnP
cap.
2.3.1
Installing the CPU
To install a CPU:
1.
Locate the CPU socket on the motherboard.
2.
Remove the PnP caps from the CPU sockets.
2-6
Chapter 2: Hardware Information
3.
Align the triangle mark on the CPU with
the triangle mark on the CPU Carrier
(A), then install the CPU into the CPU
Carrier until it clicks firmly into place (B),
and then install the CPU Carrier into the
heatsink until it clicks firmly in place (C).
CPU Carrier
Ensure that the triangle mark on the
CPU matches the triangle mark on
the CPU Carrier.
Triangle mark
2
CPU
4.
Align the CPU and CPU Carrier in the correct orientation, and then place the heatsinks
on top of the CPU sockets.
The CPU and CPU Carrier fits in only one correct orientation. DO NOT force the CPU and
CPU Carrier into the socket to prevent damaging the CPU pins on the socket.
5.
Twist each of the four screws with a screwdriver just enough to attach the heatsink to
the motherboard. When the four screws are attached, tighten them one by one in a
diagonal sequence to completely secure the heatsink.
The heatsink screws are T30 models. A torque value of 12 inch-lbf is recommended.
2-7
Z11PA-D8C Series
2.4
System memory
Overview
2.4.1
The motherboard comes with eight (8) Double Data Rate 4 (DDR4) Dual Inline Memory
Modules (DIMM) sockets.
The figure illustrates the location of the DDR4 DIMM sockets:
2.4.2
Memory Configurations
You may install 4 GB, 8 GB, 16 GB, and 32 GB RDIMMs or 32 GB and 64 GB LR-DIMMs into
the DIMM sockets using the memory configurations in this section.
•
•
•
Refer to ASUS Server AVL for the updated list of compatible DIMMs.
When installing DIMMs, always start from slot A1 (CPU1) and G1 (CPU2).
Always install DIMMs with the same CAS latency. For optimum compatibility, it is
recommended that you obtain memory modules from the same vendor.
2-8
Chapter 2: Hardware Information
Single CPU configuration
You can refer to the following recommended memory population for a single CPU
configuration.
Single CPU configuration (must be installed on CPU1)
DIMM
A1
P
B1
D1
E1
1 DIMM
2 DIMMs
4 DIMMs
P
P
P
P
P
P
Dual CPU configuration
You can refer to the following recommended memory population for a dual CPU configuration.
Dual CPU configuration
DIMM
A1
P
B1
D1
E1
G1
P
H1
K1
L1
2 DIMMs
4 DIMMs
8 DIMMs
P
P
P
P
P
P
P
P
P
P
P
P
2-9
Z11PA-D8C Series
2.4.3
Installing a DIMM on a single clip DIMM socket
Ensure to unplug the power supply before adding or removing DIMMs or other system
components. Failure to do so may cause severe damage to both the motherboard and the
components.
DIMM notch
1.
Unlock a DIMM socket by pressing the
retaining clip outward.
2.
Align a DIMM on the socket such that
the notch on the DIMM matches the
DIMM slot key on the socket.
Unlocked retaining clip
DIMM slot key
A DIMM is keyed with a notch so that it fits in only one direction. DO NOT force a DIMM into
a socket in the wrong direction to avoid damaging the DIMM.
3.
Hold the DIMM by both of its ends
then insert the DIMM vertically into the
socket. Apply force to both ends of the
DIMM simultaneously until the retaining
clip snaps back into place and the
DIMM cannot be pushed in any further
to ensure proper sitting of the DIMM.
Locked Retaining Clip
Always insert the DIMM into the socket vertically to prevent DIMM notch damage.
2.4.4
Removing a DIMM from a single clip DIMM socket
1.
Press the retaining clip outward to
unlock the DIMM.
2.
Remove the DIMM from the socket.
Support the DIMM lightly with your fingers when pressing the retaining clips. The DIMM
might get damaged when it flips out with extra force.
2-10
Chapter 2: Hardware Information
2.5
Expansion slots
In the future, you may need to install expansion cards. The following subsections describe the
slots and the expansion cards that they support.
Ensure to unplug the power cord before adding or removing expansion cards. Failure to do
so may cause you physical injury and damage motherboard components.
2.5.1
Installing an expansion card
To install an expansion card:
1.
Before installing the expansion card, read the documentation that came with it and
make the necessary hardware settings for the card.
2.
Remove the system unit cover (if your motherboard is already installed in a chassis).
3.
Remove the bracket opposite the slot that you intend to use. Keep the screw for later
use.
4.
Align the card connector with the slot and press firmly until the card is completely
seated on the slot.
5.
6.
Secure the card to the chassis with the screw you removed earlier.
Replace the system cover.
2.5.2
Configuring an expansion card
After installing the expansion card, configure it by adjusting the software settings.
1.
Turn on the system and change the necessary BIOS settings, if any. See Chapter 4 for
information on BIOS setup.
2.
Assign an IRQ to the card.
Refer to the table Standard Interrupt assignments in section Interrupt assignments for
more information.
3.
Install the software drivers for the expansion card.
When using PCI cards on shared slots, ensure that the drivers support “Share IRQ” or that
the cards do not need IRQ assignments. Otherwise, conflicts may arise between the two
PCI groups, making the system unstable and the card inoperable.
2-11
Z11PA-D8C Series
2.5.3
Interrupt assignments
Standard Interrupt assignments
IRQ
0
Priority Standard function
1
System Timer
1
2
Keyboard Controller
2
-
Programmable Interrupt
Communications Port (COM2)
Communications Port (COM1)
--
3*
11
12
13
14
15
3
4*
5*
6
Floppy Disk Controller
--
7*
8
System CMOS/Real Time Clock
ACPI Mode when used
IRQ Holder for PCI Steering
IRQ Holder for PCI Steering
PS/2 Compatible Mouse Port
Numeric Data Processor
Primary IDE Channel
Secondary IDE Channel
9*
4
10*
11*
12*
13
14*
15*
5
6
7
8
9
10
* These IRQs are usually available for ISA or PCI devices.
2.5.4
PCI Express x16 slot (x16 link)
The onboard PCIE3 and PCIE5 slots provides one x16 Gen3 link to CPU1. This slot supports
VGA cards and various server class high performance add-on cards.
2.5.5
PCI Express x8 slot (x8 link)
The onboard PCIE1 slot provides one x8 Gen3 link to CPU2. These slots support VGA cards
and various server class high performance add-on cards.
2-12
Chapter 2: Hardware Information
Slot
Short description
PCIE5
PCIE3
PCIE1
PCI-E x16 (x16 Gen3 Link)
PCI-E x16 (x16 Gen3 Link)
PCI-E x8 (x8 Gen3 Link)
2-13
Z11PA-D8C Series
2.6
Jumpers
1.
Clear RTC RAM (3-pin CLRTC1)
This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can
clear the CMOS memory of date, time, and system setup parameters by erasing the
CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS
which include system setup information such as system passwords.
To erase the RTC RAM:
1.
Turn OFF the computer and unplug the power cord.
2.
Move the jumper cap from the default pins 1–2 to pins 2–3. Keep the cap on pins
2–3 for about 5 to 10 seconds, then move the cap back to pins 1–2.
3.
Plug the power cord and turn ON the computer.
4.
Hold down the <Del> key during the boot process and enter BIOS setup to re-
enter data.
DO NOT remove the cap on CLRTC jumper default position except when clearing the RTC
RAM. Removing the cap will cause system boot failure!
If the steps above do not help, remove the onboard battery and move the jumper again to
clear the CMOS RTC RAM data. After the CMOS clearance, reinstall the battery.
2-14
Chapter 2: Hardware Information
2.
VGA controller setting (3-pin VGA_SW1)
This jumper allows you to enable or disable the onboard VGA controller. Set to pins 1–2
to activate the VGA feature.
3.
LAN controller setting (3-pin LAN_SW1-4)
These jumpers allow you to enable or disable the onboard LAN_SW1-4. Set to pins 1-2
to activate the Gigabit LAN feature.
2-15
Z11PA-D8C Series
4.
ME firmware force recovery setting (3-pin ME_RCVR1)
This jumper allows you to force Intel® Management Engine (ME) boot from recovery
mode when ME becomes corrupted.
5.
DDR4 thermal event setting (3-pin DIMMTRIP1-2)
This jumper allows you to enable or disable DDR4 DIMM thermal sensing event pin.
2-16
Chapter 2: Hardware Information
6.
PMBus 1.2 PSU select jumper (3-pin SMART_PSU1)
This jumper allows you to select PSU PMBus version. Set to pins 1–2 for PMBus, set
to pins 2–3 for others.
7.
DMLAN setting (3-pin DM_IP_EN1)
This jumper allows you to select the DMLAN setting. Set to pins 2-3 to force the
DMLAN IP to static mode (IP=10.10.10.10, submask=255.255.255.0).
2-17
Z11PA-D8C Series
8.
IPMI SW setting (3-pin IPMI_SW1)
This jumper allows you to select which protocol in the GPU sensor to function.
9.
Baseboard Management Controller setting (3-pin BMC_EN1)
This jumper allows you to enable (default) or disable on-board BMC. Ensure to set this
BMC jumper to enabled to avoid system fan control and hardware monitor error.
2-18
Chapter 2: Hardware Information
10. PCH_MFG1 setting (3-pin PCH_MFG1)
This jumper allows you to update the BIOS ME block.
2-19
Z11PA-D8C Series
2.7
1.
Onboard LEDs
Standby Power LED (SB_PWR1)
The motherboard comes with a standby power LED. The green LED lights up to
indicate that the system is ON, in sleep mode, or in soft-off mode. This is a reminder
that you should shut down the system and unplug the power cable before removing or
plugging in any motherboard component. The illustration below shows the location of
the onboard LED.
2.
BMC LED (BMCLED1)
The BMC LED blinks to indicate that the on-board BMC is functional.
2-20
Chapter 2: Hardware Information
3.
Storage device activity LED (HDDLED1)
This LED is for the storage devices connected to the onboard SATA, or SATA/SAS
add-on card. The read or write activities of any device connected to the onboard SATA,
or SATA/SAS add-on card causes the rear panel LED to light up.
4.
Location LED (LOCLED1)
This onboard LED lights up when the Location button on the server is pressed or when
triggered by a system management software. The Location LED helps visually locate
and quickly identify the server in error on a server rack.
2-21
Z11PA-D8C Series
5.
Message LED (MESLED1)
This onboard LED lights up to red when there is a BMC event log is generated.
6.
CATTLED (CATTERR_LED1)
The CATTLED indicates that the system has experienced a fatal or catastrophic error
and cannot continue to operate.
2-22
Chapter 2: Hardware Information
7.
Q-Code LEDs (PORT80_LED1)
The Q-Code LED design provides you with a 2-digit error code that displays the system
status.
•
•
The Q-Code LEDs provide the most probable cause of an error code as a starting
point for troubleshooting. The actual cause may vary from case to case.
Please refer to the Q-Code table in the Appendix section for more details.
2-23
Z11PA-D8C Series
2.8
Connectors
2.8.1
Rear panel connectors
1.
2.
RJ-45 port for iKVM. This RJ-45 port functions only when you enable ASMB9 controller.
Video Graphics Adapter (VGA) port. This port is for a VGA monitor or other VGA-
compatible devices.
3.
RJ-45 ports 1 and 2 for LAN. These ports allows Gigabit connection to a LAN through a
network hub. Refer to the LAN port LED indications table for more information.
4.
5.
Power-on Button. Press this button to turn on the system.
USB 3.0 ports 3 and 4. These two 4-pin Universal Serial Bus (USB) ports are available
for connecting USB 3.0 devices.
6.
USB 3.0 ports 5 and 6. These two 4-pin Universal Serial Bus (USB) ports are available
for connecting USB 3.0 devices.
LAN port 1-2
LAN port LED indications
Activity/Link LED
ACT/LINK SPEED
LED LED
Speed LED
Description
Status
OFF
Description
No link
Status
OFF
10 Mbps connection
100 Mbps connection
1 Gbps connection
GREEN
Linked
ORANGE
GREEN
BLINKING
Data activity
ACT/LINK SPEED
LED LED
Management LAN port LED indications
ACT/LINK SPEED
LED LED
Activity/Link LED
Status Description
Speed LED
Description
Status
OFF
OFF
No link
10 Mbps connection
100 Mbps connection
1 Gbps connection
ORANGE
BLINKING
Linked
ORANGE
GREEN
Data activity
2-24
Chapter 2: Hardware Information
2.8.2
Internal connectors
1.
Mini-SAS HD connector (ISATA1-2)
This motherboard comes with mini Serial Attached SCSI (SAS) HD connectors, the
storage technology that supports Serial ATA. Each connector supports up to four
devices.
2.
Micro SD card slot (MSD1)
Your motherboard supports SD Memory Card v2.00 (SDHC) / v3.00 (SDXC).
Disconnect all power (including redundant PSUs) from the existing system before you add
or remove a Memory Card, then reboot the system to access the Memory Card.
Some memory cards may not be compatible with your motherboard. Ensure that you use
only compatible memory cards to prevent loss of data, damage to your device, or memory
card, or both.
2-25
Z11PA-D8C Series
3.
Power Supply SMBus connector (5-pin PSUSMB1)
This connector allows you to connect SMBus (System Management Bus) to the PSU
(power supply unit) to read PSU information. Devices communicate with an SMBus
host and/or other SMBus devices using the SMBus interface.
This connector functions only when you install the ASUS ASMB8.
Power supply is required to meet PMBus specification and customized BMC FW may be
needed. Please contact ASUS if your need further support.
4.
M.2 (NGFF) connector (NGFF1)
These connector allows you to install an M.2 device.
This connector supports type 22110 devices on both PCI-E and SATA interface.
The M.2 (NGFF) device is purchased separately.
2-26
Chapter 2: Hardware Information
5.
USB 2.0 connector (10-1 pin USB78)
This connector is for USB 2.0 ports. Connect the USB module cable to the connector,
and then install the module to a slot opening at the back of the system chassis. The
USB connectors comply with USB 2.0 specification that supports up to 480 Mbps
connection speed.
6.
USB 3.0 connector (20-1 pin USB3_12)
This connector allows you to connect a USB 3.0 module for additional USB 3.0 front
or rear panel ports. With an installed USB 3.0 module, you can enjoy all the benefits of
USB 3.0 including faster data transfer speeds of up to 5Gbps, faster charging time for
USB-chargeable devices, optimized power efficiency, and backward compatibility with
USB 2.0.
2-27
Z11PA-D8C Series
7.
CPU, front, and rear fan connectors (4-pin CPU_FAN1-2; FRNT_FAN1-4;
REAR_FAN1-2)
The fan connectors support cooling fans. Connect the fan cables to the fan connectors
on the motherboard, ensuring that the black wire of each cable matches the ground pin
of the connector.
•
DO NOT forget to connect the fan cables to the fan connectors. Insufficient air flow
inside the system may damage the motherboard components.
•
•
These are not jumpers! DO NOT place jumper caps on the fan connectors!
All fans feature the ASUS Smart Fan technology.
8.
Serial port connector (10-1 pin COM1)
This connector is for the serial COM port. Connect the serial port module cable to one
of these connectors, then install the module to a slot opening at the back of the system
chassis.
2-28
Chapter 2: Hardware Information
9.
Trusted Platform Module connector (14-1 pin TPM1)
This connector supports a Trusted Platform Module (TPM) system, which can securely
store keys, digital certificates, passwords, and data. A TPM system also helps enhance
network security, protects digital identities, and ensures platform integrity.
10. VROC KEY connector (4-pin VROC_KEY1)
This connector allows you to connect a KEY module to enable additional CPU RAID
functions with Intel® CPU RSTe.
The KEY module is purchased separately.
2-29
Z11PA-D8C Series
11. EATX power connectors (24-pin EATXPWR1; 8-pin EATX12V1-2)
These connectors are for the SSI or ATX power supply plugs. The power supply plugs
are designed to fit these connectors in only one orientation. Find the proper orientation
and push down firmly until the connectors completely fit.
•
•
•
DO NOT forget to connect the 24+8-pin power plugs when using 85W or below CPU;
otherwise, the system will not boot up.
DO NOT forget to connect the 24+8+8-pin power plugs when using 105W or above
CPU; otherwise, the system will not boot up.
Use of a PSU with a higher power output is recommended when configuring a system
with more power-consuming devices. The system may become unstable or may not
boot up if the power is inadequate.
•
Ensure that your power supply unit (PSU) can provide at least the minimum power
required by your system. Minimum requirement of ATX power supply 1) 500W 2)
All+12V output > 20A.
2-30
Chapter 2: Hardware Information
12. System panel connector (20-1 pin PANEL1)
This connector supports several chassis-mounted functions.
1. System power LED (3-pin PLED)
This 3-pin connector is for the system power LED. Connect the chassis power
LED cable to this connector. The system power LED lights up when you turn on
the system power, and blinks when the system is in sleep mode.
2. Message LED (2-pin MLED)
This 2-pin connector is for the message LED cable that connects to the front
message LED. The message LED is controlled by Hardware monitor to indicate
an abnormal event occurrence.
3. System warning speaker (4-pin SPEAKER)
This 4-pin connector is for the chassis-mounted system warning speaker. The
speaker allows you to hear system beeps and warnings.
4. Hard disk drive activity LED (2-pin HDD LED)
This 2-pin connector is for the HDD Activity LED. Connect the HDD Activity LED
cable to this connector. The HDD LED lights up or flashes when data is read from
or written to the HDD.
5. Power button/soft-off button (2-pin PWRSW)
This connector is for the system power button. Pressing the power button turns
the system on or puts the system in sleep or soft-off mode depending on the BIOS
settings. Pressing the power switch for more than four seconds while the system
is ON turns the system OFF.
6. Reset button (2-pin RESET)
This 2-pin connector is for the chassis-mounted reset button for system reboot
without turning off the system power.
2-31
Z11PA-D8C Series
13. Auxiliary panel connector (20-2 pin AUX_PANEL1, 20-1 pin AUX_PANEL2)
This connector is for additional front panel features including front panel SMB, locator
LED and switch, chassis intrusion, and LAN LEDs.
1.
2.
3.
Front panel SMB (6-1 pin FPSMB)
This 6-1 pin connector is for the front panel SMBus cable.
LAN activity LED (2-pin LAN1_LED, LAN2_LED)
This 2-pin connector is for the Gigabit LAN activity LEDs on the front panel.
Locator LED (2-pin LOCATORLED1, 2-pin LOCATORLED2)
This 2-pin connector is for the locator LED1 and LED2 on the front panel. Connect
the Locator LED cables to these 2-pin connector. The LEDs will light up when the
Locator button is pressed.
4.
5.
Locator Button/Switch (2-pin LOCATORBTN)
This 2-pin connector is for the locator button on the front panel. This button
queries the state of the system locator.
LAN activity LED and USB port (2-pin LAN3_LED, LAN4_LED, USB ports)
These leads are for the Gigabit LAN activity LEDs and USB ports on the front
panel.
2-32
Chapter 2: Hardware Information
14. Hard disk activity LED connector (4-pin HDLED1)
This LED connector is for the storage add-on card cable connected to the SATA or
SAS add-on card. The read or write activities of any device connected to the SATA or
SAS add-on card causes the front panel LED to light up.
15. Chassis Intrusion (2-pin INTRUSION1)
These leads are for the intrusion detection feature for chassis with intrusion sensor or
microswitch. When you remove any chassis component, the sensor triggers and sends
a high level signal to these leads to record a chassis intrusion event. The default setting
is short CHASSIS# and GND pin by jumper cap to disable the function.
2-33
Z11PA-D8C Series
16. System Management Bus (SMBUS) connector (5-1 pin SMBUS1)
This connector controls the system and power management-related tasks. This
connector processes the messages to and from devices rather than tripping the
individual control lines.
17. VPP_I2C1 connector (10-1 pin VPP_I2C1)
This connector is used for the Intel VMD function and sensor readings.
2-34
Chapter 2: Hardware Information
18. LAN Activity LED connector (5-1 pin LAN34_LED1)
These leads are for LAN activity LEDs on the front panel. Connect the LAN LED cable
to the backplane for LAN activity indication.
2-35
Z11PA-D8C Series
2-36
Chapter 2: Hardware Information
3.1
Starting up for the first time
1.
2.
3.
4.
5.
After making all the connections, replace the system case cover.
Be sure that all switches are off.
Connect the power cord to the power connector at the back of the system chassis.
Connect the power cord to a power outlet that is equipped with a surge protector.
Turn on the devices in the following order:
a. Monitor
b. External storage devices (starting with the last device on the chain)
c. System power
6.
After applying power, the system power LED on the system front panel case lights up.
For systems with ATX power supplies, the system LED lights up when you press the
ATX power button. If your monitor complies with “green” standards or if it has a “power
standby” feature, the monitor LED may light up or switch between orange and green
after the system LED turns on.
The system then runs the power-on self-test or POST. While the tests are running, the
BIOS beeps or additional messages appear on the screen. If you do not see anything
within 30 seconds from the time you turned on the power, the system may have failed
a power-on test. Check the jumper settings and connections or call your retailer for
assistance.
The following shows the possible beep codes and its corresponding error condition
BIOS Beep codes
Beep
Error condition
Power supply surges detected during the previous power on.
No Keyboard Detected.
1 short
1 short
1 short, 2 short
1 short, 8 short
2 long
No DIMM Detected.
No VGA Detected.
Chassis Intrusion.
2 long
BIOS-image Crash Detected.
7.
At power on, hold down the <Del> key to enter the BIOS Setup. Follow the instructions
in Chapter 4.
3-2
Chapter 3: Powering Up
3.2
Powering off the computer
3.2.1
Using the OS shut down function
Using Windows® Server 2012 R2:
1.
2.
3.
4.
Press <Ctrl>+<Alt>+<Del>.
Click on the Power icon on the lower right side of the screen.
Select Shut down.
In the Shutdown Event Tracker, select the Other (Planned) option in the selection
list. Otherwise, select the option that best describes why you want to shut down the
computer.
5.
Click Continue.
Using Windows® Server 2016:
1.
2.
3.
Press <Alt>+<F4>.
In the What do you want the computer to do?, select Shut down.
In the Shutdown Event Tracker, select the Other (Planned) option in the selection
list. Otherwise, select the option that best describes why you want to shut down the
computer.
4.
Click OK.
3.2.2
Using the dual function power switch
While the system is ON, press the power switch for less than four seconds to put the system
to sleep mode or to soft-off mode, depending on the BIOS setting.
Pressing the power switch for more than four seconds lets the system enter the soft-off
mode regardless of the BIOS setting.
3-3
Z11PA-D8C Series
3-4
Chapter 3: Powering Up
4.1
Managing and updating your BIOS
The following utilities allow you to manage and update the motherboard Basic Input/Output
System (BIOS) setup:
1.
ASUS CrashFree BIOS 3
To recover the BIOS using a bootable USB flash disk drive when the BIOS file fails or
gets corrupted.
2.
3.
ASUS EzFlash
Updates the BIOS using a USB flash disk.
BUPDATER
Updates the BIOS in DOS mode using a bootable USB flash disk drive.
Refer to the corresponding sections for details on these utilities.
Save a copy of the original motherboard BIOS file to a bootable USB flash disk drive in
case you need to restore the BIOS in the future. Copy the original motherboard BIOS using
the BUPDATER utility.
4.1.1
ASUS CrashFree BIOS 3 utility
The ASUS CrashFree BIOS 3 is an auto recovery tool that allows you to restore the BIOS file
when it fails or gets corrupted during the updating process. You can update a corrupted BIOS
file using a USB flash drive that contains the updated BIOS file.
Prepare a USB flash drive containing the updated motherboard BIOS before using this
utility.
Recovering the BIOS from a USB flash drive
To recover the BIOS from a USB flash drive:
1.
Insert the USB flash drive with the original or updated BIOS file to one USB port on the
system.
2.
The utility will automatically recover the BIOS. It resets the system when the BIOS
recovery finished.
DO NOT shut down or reset the system while recovering the BIOS! Doing so would cause
system boot failure!
The recovered BIOS may not be the latest BIOS version for this motherboard. Visit the
ASUS website at www.asus.com to download the latest BIOS file.
4-2
Chapter 4: BIOS Setup
4.1.2
ASUS EZ Flash Utility
The ASUS EZ Flash Utility feature allows you to update the BIOS without having to use a
DOS-based utility.
Before you start using this utility, download the latest BIOS from the ASUS website at
www.asus.com.
To update the BIOS using EZ Flash Utility:
1.
Insert the USB flash disk that contains the latest BIOS file into the USB port.
2.
Enter the BIOS setup program. Go to the Tool menu then select ASUS EZ Flash
Utility. Press <Enter>.
ASUS Tek. EzFlash Utility
New Platform
Platform : Z11PA-D8C
Version : 0022
Current Platform
Platform : Z11PA-D8C
Version : 0020
Build Date :01/01/2017
Build Date :12/04/2016
FS0
System Volume Information
Z11PA-D8C BIOS
Windows
<DIR>
<DIR>
<DIR>
[Up/Down/Left/Right]:Switch [Enter]:Choose [q]:Exit
3.
Press <Tab> to switch to the Drive field.
4.
Press the Up/Down arrow keys to find the USB flash disk that contains the latest BIOS,
then press <Enter>.
5.
Press <Tab> to switch to the Folder Info field.
4-3
Z11PA-D8C Series
6.
Press the Up/Down arrow keys to find the BIOS file, and then press <Enter> to perform
the BIOS update process. Reboot the system when the update process is done.
•
•
This function can support devices such as a USB flash disk with FAT 32/16 format and
single partition only.
DO NOT shut down or reset the system while updating the BIOS to prevent system
boot failure!
Ensure to load the BIOS default settings to ensure system compatibility and stability. Press
<F5> and select Yes to load the BIOS default settings.
4.1.3
BUPDATER utility
The succeeding BIOS screens are for reference only. The actual BIOS screen displays
may not be the same as shown.
The BUPDATER utility allows you to update the BIOS file in the DOS environment using a
bootable USB flash disk drive with the updated BIOS file.
Updating the BIOS file
To update the BIOS file using the BUPDATER utility:
1.
2.
3.
Visit the ASUS website at www.asus.com and download the latest BIOS file for the
motherboard. Save the BIOS file to a bootable USB flash disk drive.
Copy the BUPDATER utility (BUPDATER.exe) from the ASUS support website at
https://www.asus.com/support to the bootable USB flash disk drive you created earlier.
Boot the system in DOS mode, then at the prompt, type:
BUPDATER /i[filename].CAP
where [filename] is the latest or the original BIOS file on the bootable USB flash disk
drive, then press <Enter>.
A:\>BUPDATER /i[file name].CAP
4-4
Chapter 4: BIOS Setup
4.
The utility verifies the file, then starts updating the BIOS file.
ASUS Tek. EzFlash Utility
Current Platform
Platform : Z11PA-D8C
: 0020
Build date: 12/04/2016
New Platform
Platform : Z11PA-D8C
Version : 0022
Build date: 01/01/2017
Version
Start Programming Flash. DO NOT SHUTDOWN THE SYSTEM!!!
Write
75%
DO NOT shut down or reset the system while updating the BIOS to prevent system boot
failure!
5.
The utility returns to the DOS prompt after the BIOS update process is completed.
Reboot the system from the hard disk drive.
The BIOS update is finished! Please restart your system.
C:\>
4-5
Z11PA-D8C Series
4.2
BIOS setup program
This motherboard supports a programmable firmware chip that you can update using the
provided utility described in section 4.1 Managing and updating your BIOS.
Use the BIOS Setup program when you are installing a motherboard, reconfiguring your
system, or prompted to “Run Setup.” This section explains how to configure your system
using this utility.
Even if you are not prompted to use the Setup program, you can change the configuration of
your computer in the future. For example, you can enable the security password feature or
change the power management settings. This requires you to reconfigure your system using
the BIOS Setup program so that the computer can recognize these changes and record them
in the CMOS RAM of the firmware chip.
The firmware chip on the motherboard stores the Setup utility. When you start up the
computer, the system provides you with the opportunity to run this program. Press <Del>
during the Power-On Self-Test (POST) to enter the Setup utility; otherwise, POST continues
with its test routines.
If you wish to enter Setup after POST, restart the system by pressing <Ctrl>+<Alt>+<Delete>,
or by pressing the reset button on the system chassis. You can also restart by turning the
system off and then back on. Do this last option only if the first two failed.
The Setup program is designed to make it as easy to use as possible. Being a menu-driven
program, it lets you scroll through the various sub-menus and make your selections from the
available options using the navigation keys.
•
The default BIOS settings for this motherboard apply for most conditions to ensure
optimum performance. If the system becomes unstable after changing any BIOS
settings, load the default settings to ensure system compatibility and stability. Press
<F5> and select Yes to load the BIOS default settings.
•
•
The BIOS setup screens shown in this section are for reference purposes only, and
may not exactly match what you see on your screen.
Visit the ASUS website (www.asus.com) to download the latest BIOS file for this
motherboard.
4-6
Chapter 4: BIOS Setup
4.2.1
Menu items
BIOS menu screen
Menu bar
Configuration fields
General help
Navigation keys
4.2.2
Menu bar
The menu bar on top of the screen has the following main items:
Main
For changing the basic system configuration
For changing the performance settings
For changing the advanced system settings
Performance Tuning
Advanced
Platform Configuration For changing the platform settings
Socket Configuration
Event Logs
Server Mgmt
Security
For changing the socket settings
For changing the event log settings
For changing the Server Mgmt settings
For changing the security settings
For changing the system boot configuration
For configuring options for special functions
For selecting the exit options
Boot
Tool
Save & Exit
To select an item on the menu bar, press the right or left arrow key on the keyboard until the
desired item is highlighted.
4-7
Z11PA-D8C Series
4.2.3
Menu items
The highlighted item on the menu bar displays the specific items for that menu. For example,
selecting Main shows the Main menu items.
The other items (such as Advanced) on the menu bar have their respective menu items.
4.2.4
Submenu items
A solid triangle before each item on any menu screen means that the item has a submenu.
To display the submenu, select the item then press <Enter>.
4.2.5
Navigation keys
At the bottom right corner of a menu screen are the navigation keys for the BIOS setup
program. Use the navigation keys to select items in the menu and change the settings.
4.2.6
General help
At the top right corner of the menu screen is a brief description of the selected item.
4.2.7
Configuration fields
These fields show the values for the menu items. If an item is user-configurable, you can
change the value of the field opposite the item. You cannot select an item that is not user-
configurable.
A configurable field is enclosed in brackets, and is highlighted when selected. To change the
value of a field, select it and press <Enter> to display a list of options.
4.2.8
Pop-up window
Select a menu item and press <Enter> to display a pop-up window with the configuration
options for that item.
4.2.9
Scroll bar
A scroll bar appears on the right side of a menu screen when there are items that do not fit
on the screen. Press the Up/Down arrow keys or <Page Up> / <Page Down> keys to display
the other items on the screen.
4-8
Chapter 4: BIOS Setup
4.3
Main menu
When you enter the BIOS Setup program, the Main menu screen appears. The Main menu
provides you an overview of the basic system information, and allows you to set the system
date, time, language, and security settings.
4.3.1
System Date [Day xx/xx/xxxx]
Allows you to set the system date.
4.3.2
System Time [xx:xx:xx]
Allows you to set the system time.
4-9
Z11PA-D8C Series
4.4
Performance Tuning menu
The Performance Tuning menu items allow you to change performance related settings for
different scenarios.
Optimized Performance Setting [Default]
Allows you to select performance settings for different scenarios.
[Default]
Default settings.
[By Benchmark] Optimize for different kinds of benchmarks. Select this option, then select a
benchmark type from the >> list.
[By Workload]
Optimize for different kinds of workloads. Select this option, then select a
workload type from the >> list.
Configuration options:
[Peak Frequency Optimized] - Applies settings with performance and
power consumption balance. Recommended for users that need higher
performance.
[Latency Optimized] - Applies settings with low latency results.
Recommended for latency-sensitive users.
[Power Efficient Optimized] - Applies settings with power efficiency.
Recommended for general users.
[HPC] - Applies settings with optimized compute capability. Recommend
for traditional HPC applications.
Core Optimizer and Engine Boost appear only when you set Optimized Performance
Setting to [Default] or [By Benchmark].
Core Optimizer [Disabled]
Enable this item to keep the processor operating at the turbo frequency.
Configuration options: [Disabled] [Enabled]
Linux support may vary by version of the OS.
Engine Boost [Disabled]
Enable this item to boost the CPU's frequency.
Configuration options: [Disabled] [Level1] [Level2] [Level3(Max)]
4-10
Chapter 4: BIOS Setup
Overclocking [Disabled]
Enable this item to increase the CPU’s clock.
Configuration options: [Disabled] [Level1] [Level2] [Level3(Max)]
Operate with an ambient temperature of 25°C or lower for optimized performance.
Please note that overclocking might cause component damage or system crashes, which
may reduce the lifespan of the system and the CPU. Use this tool at your own risk.
Power Balancer [Disabled]
Select [Enable Auto] to dynamically adjust the frequency of all CPU cores based on the
current utilization, delivering better performance per watt for improved system energy
efficiency.
Configuration options: [Disabled] [Enable Auto] [Enable Manual]
4.5
Advanced menu
The Advanced menu items allow you to change the settings for the CPU and other system
devices.
Take caution when changing the settings of the Advanced menu items. Incorrect field
values can cause the system to malfunction.
4-11
Z11PA-D8C Series
4.5.1
Trusted Computing
Configuration
Security Device Support [Disabled]
Allows you to enable or disable the BIOS support for security device.
Configuration options: [Disabled] [Enabled]
4.5.2
ACPI Settings
Enable ACPI Auto Configuration [Disabled]
Allows you to enable or disable the BIOS ACPI Auto Configuration.
Configuration options: [Disabled] [Enabled]
Enable Hibernation [Enabled]
Allows you to enable or disable the ability of the system to hibernate (OS/Sleep State).
Configuration options: [Disabled] [Enabled]
This option may be not effective with some OS.
4-12
Chapter 4: BIOS Setup
4.5.3
Smart Settings
SMART Self Test [Enabled]
Allows you to run SMART Self Test on all HDDs during POST.
Configuration options: [Disabled] [Enabled]
4.5.4
Super IO Configuration
Serial Port 1 Configuration
Allows you to set the parameters of Serial Port 1.
Serial Port [Enabled]
Allows you to enable or disable Serial Port.
Configuration options: [Disabled] [Enabled]
The following item appears only when you set Serial Port to [Enabled].
Change Settings [Auto]
Allows you to choose the setting for Super IO device.
Configuration options: [Auto] [IO=3F8h; IRQ=4;]
[IO=3F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12;]
[IO=2F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12;]
[IO=3E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12;]
[IO=2E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12;]
4-13
Z11PA-D8C Series
4.5.5
Serial Port Console Redirection
COM1/COM2
Console Redirection [Disabled]
Allows you to enable or disable the console redirection feature.
Configuration options: [Disabled] [Enabled]
The following item appears only when you set Console Redirection to [Enabled].
Console Redirection Settings
These items become configurable only when you enable the Console Redirection
item. The settings specify how the host computer and the remote computer (which the
user is using) will exchange data. Both computers should have the same or compatible
settings.
Terminal Type [VT-UTF8]
Allows you to set the terminal type.
[VT100]
[VT100+]
[VT-UTF8]
[ANSI]
ASCII char set.
Extends VT100 to support color, function keys, etc.
Uses UTF8 encoding to map Unicode chars onto 1 or more bytes.
Extended ASCII char set.
Bits per second [57600]
Selects serial port transmission speed. The speed must be matched on the other side.
Long or noisy lines may require lower speeds.
Configuration options: [9600] [19200] [38400] [57600] [115200]
Data Bits [8]
Configuration options: [7] [8]
4-14
Chapter 4: BIOS Setup
Parity [None]
A parity bit can be sent with the data bits to detect some transmission errors. [Mark]
and [Space] parity do not allow for error detection.
[None]
[Even]
[Odd]
[Mark]
[Space]
None
parity bit is 0 if the num of 1’s in the data bits is even
parity bit is 0 if num of 1’s in the data bits is odd
parity bit is always 1
parity bit is always 0
Stop Bits [1]
Stop bits indicate the end of a serial data packet. (A start bit indicates the beginning.)
The standard setting is 1 stop bit. Communication with slow devices may require more
than 1 stop bit.
Configuration options: [1] [2]
Flow Control [Hardware RTS/CTS]
Flow control can prevent data loss from buffer overflow. When sending data, if the
receiving buffers are full, a “stop” signal can be sent to stop the data flow. Once the
buffers are empty, a “start” signal can be sent to re-start the flow. Hardware flow control
uses two wires to send start/stop signals.
Configuration options: [None] [Hardware RTS/CTS]
VT -UTF8 Combo Key Support [Enabled]
This allows you to enable the VT -UTF8 Combination Key Support for ANSI/VT100
terminals.
Configuration options: [Disabled] [Enabled]
Recorder Mode [Disabled]
With this mode enabled only text will be sent. This is to capture Terminal data.
Configuration options: [Disabled] [Enabled]
Legacy OS Redirection Resolution [80x24]
This allows you to set the number of rows and columns supported on the Legacy OS.
Configuration options: [80x24] [80x25]
Putty Keypad [VT100]
This allows you to select the FunctionKey and Keypad on Putty.
Configuration options: [VT100] [LINUX] [XTERMR6] [SCO] [ESCN] [VT400]
Redirection After BIOS POST [Always Enable]
This setting allows you to specify if Bootloader is selected than Legacy console
redirection.
Configuration options: [Always Enable] [Bootloader]
Legacy Console Redirection Settings
Legacy Console Redirection Port [COM1]
Allows you to select a COM port to display redirection of Legacy OS and Legacy OPROM
Messages.
Configuration options: [COM1] [COM2]
4-15
Z11PA-D8C Series
Serial Port for Out-of-Band Management/Windows Emergency Management
Services (EMS)
Console Redirection [Disabled]
Allows you to enable or disable the console redirection feature.
Configuration options: [Disabled] [Enabled]
The following item appears only when you set Console Redirection to [Enabled].
Console Redirection Settings
Out-of-Band Mgmt Port [COM1]
Microsoft Windows Emergency Management Services (EMS) allow for remote
management of a Windows Server OS through a serial port.
Configuration options: [COM1] [COM2]
Terminal Type [VT-UTF8]
Microsoft Windows Emergency Management Services (EMS) allow for remote
management of a Windows Server OS through a serial port.
Configuration options: [VT100] [VT100+] [VT-UTF8] [ANSI]
Bits per second [115200]
Microsoft Windows Emergency Management Services (EMS) allow for remote
management of a Windows Server OS through a serial port.
Configuration options: [9600] [19200] [57600] [115200]
Flow Control [None]
Microsoft Windows Emergency Management Services (EMS) allow for remote
management of a Windows Server OS through a serial port.
Configuration options: [None] [Hardware RTS/CTS] [Software Xon/Xoff]
4-16
Chapter 4: BIOS Setup
4.5.6
Onboard LAN Configuration
Onboard I350 LAN Configuration
Intel LAN1 Enable [Enabled]
Allows you to enable or disable the Intel LAN.
Configuration options: [Disabled] [Enabled]
The following items appear only when Intel LAN1 Enable is set to [Enabled].
Intel LAN 1 ROM Type [PXE]
Allows you to select the Intel LAN ROM type.
Configuration options: [PXE] [iSCSI] [Disabled]
Intel LAN2 Enable [Enabled]
Allows you to enable or disable the Intel LAN.
Configuration options: [Disabled] [Enabled]
The following items appear only when Intel LAN2 Enable is set to [Enabled].
Intel LAN 2 ROM Type [Disabled]
Allows you to select the Intel LAN ROM type.
Configuration options: [PXE] [iSCSI] [Disabled]
4-17
Z11PA-D8C Series
4.5.7
APM
Allows you to configure the Advance Power Management (APM) settings.
Restore AC Power Loss [Last State]
When set to [Power Off], the system goes into off state after an AC power loss. When set
to [Power On], the system will reboot after an AC power loss. When set to [Last State], the
system goes into either off or on state, whatever the system state was before the AC power
loss.
Configuration options: [Power Off] [Power On] [Last State]
Power On By PCIE [Disabled]
[Disabled]
Disables the PCIE devices to generate a wake event.
[Enabled]
Enables the PCIE devices to generate a wake event.
Power On By RTC [Disabled]
[Disabled]
Disables RTC to generate a wake event.
[Enabled]
When set to [Enabled], the items RTC Alarm Date (Days) and
Hour/Minute/Second will become user-configurable with set values.
4-18
Chapter 4: BIOS Setup
4.5.8
PCI Subsystem Settings
Allows you to configure PCI, PCI-X, and PCI Express Settings.
Load RT32 Image [Enabled]
This option allows you to enable or disable RT32 Image Loading.
Configuration options: [Disabled] [Enabled]
Above 4G Decoding [Disabled]
Allows you to enable or disable 64-bit capable devices to be decoded in above 4G address
space. It only works if the system supports 64-bit PCI decoding.
Configuration options: [Disabled] [Enabled]
SR-IOV Support [Enabled]
This option enables or disables SIngle Root IO Virtualization Support if the system has SR-
IOV capable PCIe devices.
Configuration options: [Disabled] [Enabled]
BME DMA Mitigation [Disabled]
This allows you to enable or disable re-enabling Bus Master Attribute disabled during PCI
enumeration for PCI Bridges after SMM locked.
Configuration options: [Disabled] [Enabled]
PCIE Express Settings
PCI Express Device Register Settings
Relaxed Ordering [Enabled]
Enables or disables PCI Express device relaxed ordering.
Configuration options: [Disabled] [Enabled]
Extended Tag [Disabled]
If Enable allows device is use 8-bit tag field as a requester.
Configuration options: [Disabled] [Enabled]
No Snoop [Enabled]
Enables or disables PCI Express device No snoop option.
Configuration options: [Disabled] [Enabled]
4-19
Z11PA-D8C Series
PCI Express Link Register Settings
ASPM Support [Disabled]
Allows to set the ASPM level. Configuration options: [Disabled] [Auot] [Force L0s]
[Force L0s]
[Auto]
[Disabled]
Force all links to L0s state.
BIOS auto configure.
Disabled ASPM.
Unpopulated Links [Keep Link ON]
In order to save power, software will disable unpopulated PCI Express links, if this
option set to Disabled.
Configuration options: [Keep Link ON] [Disabled]
PCIE OPROM Slot Options
PCIE1-3 Slot OPROM [Enabled]
This option allows you to enable or disable the OPROM of the PCIe slots.
Configuration options: [Disabled] [Enabled]
MEZZ1 Slot OPROM [Enabled]
This option allows you to enable or disable the OPROM of the MEZZ slot.
Configuration options: [Disabled] [Enabled]
4-20
Chapter 4: BIOS Setup
4.5.9
USB Configuration
Legacy USB Support [Enabled]
Allows you to enable or disable Legacy USB device support.
Configuration options: [Enabled] [Disabled] [Auto]
USB Mass Storage Driver Support [Enabled]
Allows you to enable or disable the USB Mass Storage driver support.
Configuration options: [Disabled] [Enabled]
Mass Storage Devices
AMI Virtual CDROM0-2 / Floppy / HDisk0 1.00 [Auto]
Allows you to select the mass storage device emulation type.
Configuration options: [Auto] [Floppy] [Forced FDD] [Hard Disk] [CD-ROM]
4-21
Z11PA-D8C Series
4.5.10
CSM Configuration
CSM Support [Enabled]
This option allows you to enable or disable CSM Support.
Configuration options: [Disabled] [Enabled]
The following item appears only when CSM Support is set to [Enabled].
GateA20 Active [Upon Request]
This allows you to set the GA20 option.
Configuration options: [Upon Request] [Always]
Option ROM Messages [Force BIOS]
This allows you to set the display mode for option ROM.
Configuration options: [Force BIOS] [Keep Current]
INT19 Trap Response [Immediate]
[Immediate]
Execute the trap right away.
[Postponed]
Execute the trap during legacy boot.
Boot Option filter [Legacy only]
This option allows you to control the Legacy/UEFI ROMs priority.
Configuration options: [UEFI and Legacy] [Legacy only] [UEFI only]
Network / Storage / Video [Legacy]
This option allows you to control the execution of UEFI and Legacy PXE / Storage /
Video OpROM.
Configuration options: [UEFI] [Legacy]
Other PCI devices [Legacy]
This item determines the OpROM execution policy for devices other than Network,
Storage, or Video.
Configuration options: [UEFI] [Legacy]
4-22
Chapter 4: BIOS Setup
4.5.11
NVMe Configuration
This page will display the NVMe controller and drive information.
4.5.12
Network Stack Configuration
Network stack [Disabled]
Enables or disables the network stack feature.
Configuration options: [Disable] [Enable]
The following item appears only when Network stack is set to [Enabled].
Ipv4 PXE Support [Disabled]
Enables or disables the Ipv4 PXE Boot Support. If disabled, Ipv4 PXE boot option will
not be created.
Configuration options: [Disabled] [Enabled]
Ipv4 HTTP Support [Disabled]
Enables or disables the Ipv4 HTTP Boot Support. If disabled, Ipv4 HTTP boot option
will not be created.
Configuration options: [Disabled] [Enabled]
Ipv6 PXE Support [Disabled]
Enables or disables the Ipv6 PXE Boot Support. If disabled, Ipv6 PXE boot option will
not be created.
Configuration options: [Disabled] [Enabled]
Ipv6 HTTP Support [Disabled]
Enables or disables the Ipv6 HTTP Boot Support. If disabled, Ipv6 HTTP boot option
will not be created.
Configuration options: [Disabled] [Enabled]
PXE boot wait time [0]
Wait time to press ESC key to abort the PXE boot.
Media detect time [1]
Wait time (in seconds) to detect media.
4-23
Z11PA-D8C Series
4.6.1
PCH Configuration
PCH Devices
DeepSx Power Policies [Disabled]
Allows you to configure the DeepSx Mode configuration.
Configuration options: [Disabled] [Enabled in S5] [Enabled in S4 and S5]
GP27 Wake From DeepSx [Disabled]
Allows you to enable or disable GP27 Wake From DeepSx.
Configuration options: [Disabled] [Enabled]
PCI Express Configuration
PCI-E ASPM Support (Global) [L1 Only]
Allows you to select ASPM support for all downstream devices.
Configuration options: [Per individual port] [L1 Only]
PCH DMI ASPM [Platform-POR]
Allows you to configure the PCH DMI ASPM.
Configuration options: [Platform-POR] [ASPM L1] [Disabled]
PCH SATA Configuration
SATA Controller [Enabled]
Allows you to enable or disable the SATA Controller.
Configuration options: [Disabled] [Enabled]
Configure sSATA as [AHCI]
Allows you to identify the SATA port connected to Solid State Drive or Hard Disk Drive.
Configuration options: [IDE] [AHCI] [RAID]
Support Aggressive Link Power Management [Enabled]
Allows you to enable or disable the Support Aggressive Link Power (SALP)
Management.
Configuration options: [Disabled] [Enabled]
4-25
Z11PA-D8C Series
SATA Port 1-8
Port 1-8
Allows you to enable or disable the SATA port.
Configuration options: [Disabled] [Enabled]
PCH sSATA Configuration
sSATA Controller [Enabled]
Allows you to enable or disable the sSATA Controller.
Configuration options: [Disabled] [Enabled]
Configure sSATA as [AHCI]
Allows you to identify the SATA port connected to Solid State Drive or Hard Disk Drive.
Configuration options: [IDE] [AHCI] [RAID]
Support Aggressive Link Power Management [Enabled]
Allows you to enable or disable the Support Aggressive Link Power (SALP)
Management.
Configuration options: [Disabled] [Enabled]
sSATA Port 1-3
Port 1-3
Allows you to enable or disable the SATA port.
Configuration options: [Disabled] [Enabled]
USB Configuration
USB Precondition [Disabled]
Allows you to enable or disable precondition work on USB host controller and root ports
for faster enumeration.
Configuration options: [Disabled] [Enabled]
XHCI Manual Mode [Disabled]
This option is used by validation.
Configuration options: [Disabled] [Enabled]
The following items appears only when the XHCI Manual Mode is set to [Enabled].
Trunk Clock Gating (BTCG) [Enabled]
Allows you to enable or disable BTCG.
Configuration options: [Disabled] [Enabled]
Enable USB 3.0 pins [Disable all pins]
Allows you to enable or disable USB 3.0 pins or on a per pin basis.
Configuration options: [Select Per-Pin] [Disable all pins] [Enable all pins]
USB Per-Connector Disable [Disabled]
Allows you to enable or disable each of the USB physical connectors. Once a
connector is disabled, any USB devices plugged into the connector will not be detected
by BIOS or OS.
Configuration options: [Disabled] [Enabled]
4-26
Chapter 4: BIOS Setup
The following items appears only when the USB Per-Connector Disable is set to [Enabled].
USB_1-8 [Enabled]
Configuration options: [Disabled] [Enabled]
USB3_1-5 [Enabled]
Configuration options: [Disabled] [Enabled]
Security Configuration
SMM BIOS Write Protect [Enabled]
Allows you to enable or disable SMM BIOS Write Protect.
Configuration options: [Disabled] [Enabled]
4.6.2
Miscellaneous Configuration
Active Video [Offboard Device]
Allows you to select the video type.
Configuration options: [Auto] [Onboard Device] [Offboard Device]
4.6.3
Server ME Configuration
Displays the Server ME Technology parameters on your system.
4-27
Z11PA-D8C Series
4.6.4
Runtime Error Logging Support
Runtime Error Logging
System Errors [Enabled]
This item allows you to enable or disable System Errors.
Configuration options: [Disabled] [Enabled]
Whea Settings
Whea Support [Disabled]
This item allows you to enable or disable the WHEA support.
Configuration options: [Disabled] [Enabled]
4.7
Socket Configuration menu
The IntelRCSetup menu items allow you to change the socket settings.
4-28
Chapter 4: BIOS Setup
4.7.1
Processor Configuration
Hyper Threading [ALL] [Enabled]
Allows you to enable or disable the Hyper-Threading Technology function. When disabled,
only one thread per activated core is enabled.
Configuration options: [Disabled] [Enabled]
Enable Intel(R) TXT Support [Disabled]
Forces the XD feature log to always return 0 when disabled.
Configuration options: [Disabled] [Enabled]
VMX [Enabled]
Enables the Vanderpool Technology. Takes effect after reboot.
Configuration options: [Disabled] [Enabled]
Enable SMX [Disabled]
Enables the Safer Mode Extensions.
Configuration options: [Disabled] [Enabled]
Hardware Prefetcher [Enabled]
This Item allows you to turn on/off the mid level cache(L2) streamer prefetcher.
Configuration options: [Disabled] [Enabled]
L2 RFO Prefetch Disable [Disabled]
This Item allows you to turn on/off L2 RFO prefetcher.
Configuration options: [Disabled] [Enabled]
4-29
Z11PA-D8C Series
Adjacent Cache Prefetch [Enabled]
This Item allows you to turn on/off prefetching of adjacent cache lines.
Configuration options: [Disabled] [Enabled]
DCU Streamer Prefetcher [Enabled]
This Item allows you to enable or disable prefetcher of next L1 data line.
Configuration options: [Disabled] [Enabled]
DCU IP Prefetcher [Enabled]
This Item allows you to enable or disable prefetch of next L1 line based upon sequential load
history.
Configuration options: [Disabled] [Enabled]
LLC Prefetch [Disabled]
This Item allows you to enable or disable LLC Prefetch on all threads.
Configuration options: [Disabled] [Enabled]
DCU Mode [32K 8Way Without ECC]
Configuration options: [32K 8Way Without ECC] [16K 4Way With ECC]
Extended APIC [Disabled]
This Item allows you to enable or disable the extended APIC support.
Configuration options: [Disabled] [Enabled]
AES-NI [Enabled]
This Item allows you to enable or disable the AES-NI support.
Configuration options: [Disabled] [Enabled]
4.7.2
Common RefCode Configuration
MMIO High Base [56T]
This item allows you to select the MMIO High Base.
Configuration options: [56T] [40T] [24T] [16T] [4T] [1T]
MMIO High Granularity Size [256G]
This item allows you to select the allocation size used to assign MMIOH resources.
Configuration options: [1G] [4G] [16G] [64G] [256G] [1024G]
Numa [Enabled]
This item enables or disables the Non uniform Memory Access (NUMA).
Configuration options: [Disabled] [Enabled]
4-30
Chapter 4: BIOS Setup
4.7.3
UPI Configuration
UPI General Configuration
UPI Status
This item displays information about the UPI status.
Link Speed Mode [Fast]
This item allows you to select the UPI link speed as either the fast mode or slow mode.
Configuration options: [Slow] [Fast]
Link Frequency Select [Auto]
This item allows for selecting the UPI link frequency.
Configuration options: [Auto] [9.6 GB/s] [10.4 GB/s] [Use Per Link Setting]
UPI Link0p Enable [Enabled]
Configuration options: [Disabled] [Enabled] [Auto]
UPI Link1 Enable [Enabled]
Configuration options: [Disabled] [Enabled] [Auto]
Directory Mode Enable [Enabled]
Configuration options: [Disabled] [Enabled]
SNC [Disabled]
Configuration options: [Disabled] [Enabled] [Auto]
KTI Prefetch [Enabled]
Configuration options: [Disabled] [Enabled]
Local/Remote Threshold [Auto]
Configuration options: [Disabled] [Auto] [Low] [Medium] [High]
Stale AtoS [Disabled]
Configuration options: [Disabled] [Enabled] [Auto]
LLC dead line alloc [Enabled]
Configuration options: [Disabled] [Enabled] [Auto]
4-31
Z11PA-D8C Series
4.7.4
Memory Configuration
Enforce POR [Auto]
Allows you to enforce POR restrictions for DDR4 frequency and voltage programming.
Configuration options: [Auto] [POR] [Disabled]
Memory Frequency [Auto]
Allows you to select the memory frequency setting.
Configuration options: [Auto] [1800] - [3000-OvrClk]
Data Scrambling for DDR4 [Auto]
Allows you to enable or disable data scrambling.
Configuration options: [Auto] [Disabled] [Enabled]
Memory Topology
Displays memory topology with DIMM population information.
Page Policy
Allows you to configure Page Policy settings.
Page Policy [Disabled]
Configuration options: [Auto] [Closed] [Adaptive]
Memory Map
IMC Interleaving [Auto]
Select different IMC interleaving setting.
Configuration options: [Auto] [1-way Interleave] [2-way Interleave]
Channel Interleaving [Auto]
Select different channel interleaving setting.
Configuration options: [Auto] [1-way Interleave] [2-way Interleave]
[3-way Interleave]
4-32
Chapter 4: BIOS Setup
Rank Interleaving [Auto]
Select different rank interleaving setting.
Configuration options: [Auto] [1-way Interleave] [2-way Interleave]
[4-way Interleave] [8-way Interleave]
Memory RAS Configuration
Mirror Mode [Disabled]
Allows you to select Mirror Modes. Mirror Mode will set entire 1LM/2LM memory in
system to be mirrored, consequently reducing the memory capacity by half. Enabling
Mirror Mode will disable XPT Prefetch.
Configuration options: [Disabled] [Mirror Mode 1LM] [Mirror Mode 2LM]
UEFI ARM Mirror [Disabled]
Allows you to enable or disable UEFI ARM Mirror.
Configuration options: [Disabled] [Enabled]
Memory Rank Sparing [Disabled]
Allows you to enable or disable Memory Rank Sparing
Configuration options: [Disabled] [Enabled]
Patrol Scrub [Enabled]
Allows you to enable or disable Patrol Scrub.
Configuration options: [Disabled] [Enabled]
NGN Configuration
Average Power Budget (in mW) [18000]
Allows you to set the power management policy for average power in 250 mW
increments.
Configuration options: [10000] - [18000]
4-33
Z11PA-D8C Series
4.7.5
IIO Configuration
Socket1 Configuration
This item allows you to configure settings related to the corresponding PCIE port.
Intel(R) VT for Directed I/O (VT-d)
Intel(R) VT for Directed I/O (VT-d) [Disabled]
Allows you to enable or disable the Intel Virtualization Technology for Directed I/O.
Configuration options: [Disabled] [Enabled]
PCI Express Global Options
PCI-E ASPM Support (Global) [Per-Port]
Allows you to enable or disable ASPM support for all downstream devices.
Configuration options: [Disabled] [Per-Port] [L1 Only]
PCIE relaxed Ordering [Enabled]
Allows you to enable or disable PCIE relaxed Ordering.
Configuration options: [Disabled] [Enabled]
4-34
Chapter 4: BIOS Setup
4.7.6
Advanced Power Management Configuration
CPU P State Control
Boot performance mode [Max Performance]
Allows you to switch between Boot performance mode.
Configuration options: [Max Performance] [Max Efficient] [Set by Intel Node Manager]
Energy Efficient Turbo [Enabled]
Allows you to enable or disable Energy Efficient Turbo.
Configuration options: [Disabled] [Enabled]
Turbo Mode [Enabled]
Allows you to enable or disable Turbo Mode.
Configuration options: [Disabled] [Enabled]
Hardware PM State Control
Hardware P-States [Native Mode]
Allows you to switch between Hardware P-States mode.
Configuration options: [Disabled] [Native Mode] [Out of Band Mode] [Native Mode with
no Legacy Support]
CPU C State Control
Autonomous Core C-State [Disabled]
Allows you to enable or disable Autonomous Core C-State Report.
Configuration options: [Disabled] [Enabled]
CPU C6 Report [Auto]
Allows you to select CPU C6 Report.
Configuration options: [Disabled] [Enabled] [Auto]
OS ACPI Cx [ACPI C2]
Allows you to select OS ACPI Cx Report.
Configuration options: [ACPI C2] [ACPI C3]
Package C State Control
Package C State [Auto]
Allows you to select Package C State.
Configuration options: [C0/C1 state] [C2 state] [C6(non Retention state] [C6(Retention
state] [No Limit] [Auto]
4-35
Z11PA-D8C Series
CPU Thermal Control
CPU T-State Control
Software Controlled T-States [Disabled]
Allows you to enable or disable Software Controlled T-States.
Configuration options: [Disabled] [Enabled]
CPU - Advanced PM Tuning
Energy Perf BIAS
Power Performance Tuning [OS Controls EPB]
Configuration options: [OS Controls EPB] [BIOS Controls EPB]
The following item appears only when you set Power Performance Tuning to
[OS Controls EPB].
PECI PCS EPB [OS Controls EPB]
This option controls whether PECI has control over EPB.
Configuration options: [OS Controls EPB] [PECI Controls EPB using PCS]
The following item appears only when you set Power Performance Tuning to
[BIOS Controls EPB].
ENERGY_PERF_BIAS_CFG Mode [Balanced Performance]
Configuration options: [Performance] [Balanced Performance] [Balanced Power]
[Power]
Dynamic Loadline Switch [Enabled]
Configuration options: [Disabled] [Enabled]
Workload Configuration [UMA]
This option allows optimization for the workload characterization.
Configuration options: [UMA] [NUMA]
Averaging Time Window [17]
This option is used to control the effective window of the average C0 an P0 time.
Configuration options: [0] - [FF]
P0 TotalTimeThreshold Low [23]
The HW switching mechanism DISABLES the performance setting (0) when the total
P0 time is less than the threshold set.
Configuration options: [0] - [3F]
P0 TotalTimeThreshold High [3a]
The HW switching mechanism Enables the performance setting (0) when the total P0
time is greater than the threshold set.
Configuration options: [0] - [3F]
4-36
Chapter 4: BIOS Setup
4.8
Event Logs menu
The Event Logs menu items allow you to change the event log settings and view the system
event logs.
4.8.1
Change Smbios Event Log Settings
Press <Enter> to change the Smbios Event Log configuration.
All values changed here do not take effect until computer is restarted.
Enabling/Disabling Options
Smbios Event Log [Enabled]
Change this to enable or disable all features of Smbios Event Logging during boot.
Configuration options: [Disabled] [Enabled]
Erasing Settings
Erase Event Log [No]
Choose options for erasing Smbios Event Log. Erasing is done prior to any logging activation
during reset.
Configuration options: [No] [Yes, Next reset] [Yes, Every reset]
4.8.2
View Smbios Event Log
Press <Enter> to view all smbios event logs.
4-37
Z11PA-D8C Series
4.9
Server Mgmt menu
The Server Management menu displays the server management status and allows you to
change the settings.
OS Watchdog Timer [Disabled]
This item allows you to start a BIOS timer which can only be shut off by Intel Management
Software after the OS loads.
Configuration options: [Disabled] [Enabled]
The following items is configurable only when the OS Watchdog Timer is set to [Enabled].
OS Wtd Timer Timeout [10 minutes]
Allows you to configure the length fo the OS Boot Watchdog Timer.
Configuration options: [5 minutes] [10 minutes] [15 minutes] [20 minutes]
OS Wtd Timer Policy [Reset]
This item allows you to configure the how the system should respond if the OS Boot
Watch Timer expires.
Configuration options: [Do Nothing] [Reset] [Power Down]
System Event Log
Allows you to change the SEL event log configuration.
Erase SEL [No]
Allows you to choose options for erasing SEL.
Configuration options: [No] [Yes, On next reset] [Yes, On every reset]
When SEL is Full [Do Nothing]
Allows you to choose options for reactions to a full SEL.
Configuration options: [Do Nothing] [Erase Immediately]
BMC network configuration
The sub-items in this configuration allow you to configure the BMC network parameters.
View System Event Log
This item allows you to view the system event log records.
4-38
Chapter 4: BIOS Setup
4.10
Security menu
This menu allows a new password to be created or a current password to be changed. The
menu also enables or disables the Secure Boot state and lets the user configure the System
Mode state.
Administrator Password
To set an administrator password:
1.
2.
3.
Select the Administrator Password item and press <Enter>.
From the Create New Password box, key in a password, then press <Enter>.
Confirm the password when prompted.
To change an administrator password:
1.
Select the Administrator Password item and press <Enter>.
2.
From the Enter Current Password box, key in the current password, then press
<Enter>.
3.
4.
From the Create New Password box, key in a new password, then press <Enter>.
Confirm the password when prompted.
To clear the administrator password, follow the same steps as in changing an administrator
password, but press <Enter> when prompted to create/confirm the password.
4-39
Z11PA-D8C Series
User Password
To set a user password:
1.
2.
3.
Select the User Password item and press <Enter>.
From the Create New Password box, key in a password, then press <Enter>.
Confirm the password when prompted.
To change a user password:
1.
Select the User Password item and press <Enter>.
2.
From the Enter Current Password box, key in the current password, then press
<Enter>.
3.
4.
From the Create New Password box, key in a new password, then press <Enter>.
Confirm the password when prompted.
To clear a user password:
1.
2.
Select the Clear User Password item and press <Enter>.
Select Yes from the Warning message window then press <Enter>.
Secure Boot
This item allows you to customize the Secure Boot settings.
Secure Boot
Allows you to enable or disable Secure Boot.
Configuration options: [Disabled] [Enabled]
4-40
Chapter 4: BIOS Setup
4.11
Boot menu
The Boot menu items allow you to change the system boot options.
Bootup NumLock State [On]
Allows you to select the power-on state for the NumLock.
Configuration options: [Off] [On]
Boot Logo Display [Auto]
Allows you to enable or disable the full screen logo display feature.
Configuration options: [Auto] [Full Screen] [Disabled]
POST Report [5 sec]
Allows you to set the desired POST Report waiting time from 1 to 10 seconds.
Configuration options: [1 sec] ~ [10 sec] [Until Press ESC]
Boot Option Priorities
These items specify the boot device priority sequence from the available devices. The
number of device items that appears on the screen depends on the number of devices
installed in the system.
•
•
To select the boot device during system startup, press <F8> when ASUS Logo
appears.
To access Windows OS in Safe Mode, please press <F8> after POST.
Hard Drive / CD/DVD ROM Drive / Network Device BBS Priorities
These items appear allow you to set the order of the legacy devices in this group.
4-41
Z11PA-D8C Series
4.12
Tool menu
The Tool menu items allow you to configure options for special functions. Select an item then
press <Enter> to display the submenu.
IPMI Hardware Monitor
Allows you to run the IPMI hardware monitor.
Start EZ Flash
Allows you to run ASUS EZ Flash BIOS ROM Utility when you press <Enter>. Refer to the
ASUS EZ Flash Utility section for details.
4.13
Save & Exit menu
The Save & Exit menu items allow you to save or discard your changes to the BIOS items.
Pressing <Esc> does not immediately exit this menu. Select one of the options from this
menu or <F10> from the legend bar to exit.
Discard Changes & Exit
Exit System setup without saving any changes.
Save Changes & Reset
Exit System setup after saving the changes.
Restore Defaults
Restore/load default values for all the setup options.
Boot Override
These items displays the available devices. The device items that appears on the screen
depends on the number of devices installed in the system. Click an item to start booting from
the selected device.
4-42
Chapter 4: BIOS Setup
5.1
Setting up RAID
The motherboard supports the Intel® Rapid Storage Technology enterprise Option ROM
Utility with RAID 0, RAID 1, RAID 10, and RAID 5 support.
5.1.1
RAID definitions
RAID 0 (Data striping) optimizes two identical hard disk drives to read and write data in
parallel, interleaved stacks. Two hard disks perform the same work as a single drive but at a
sustained data transfer rate, double that of a single disk alone, thus improving data access
and storage. Use of two new identical hard disk drives is required for this setup.
RAID 1 (Data mirroring) copies and maintains an identical image of data from one drive to a
second drive. If one drive fails, the disk array management software directs all applications
to the surviving drive as it contains a complete copy of the data in the other drive. This RAID
configuration provides data protection and increases fault tolerance to the entire system. Use
two new drives or use an existing drive and a new drive for this setup. The new drive must be
of the same size or larger than the existing drive.
RAID 10 is data striping and data mirroring combined without parity (redundancy data) having
to be calculated and written. With the RAID 10 configuration you get all the benefits of both
RAID 0 and RAID 1 configurations. Use four new hard disk drives or use an existing drive and
three new drives for this setup.
RAID 5 stripes both data and parity information across three or more hard disk drives. Among
the advantages of RAID 5 configuration include better HDD performance, fault tolerance, and
higher storage capacity. The RAID 5 configuration is best suited for transaction processing,
relational database applications, enterprise resource planning, and other business systems.
Use a minimum of three identical hard disk drives for this setup.
If you want to boot the system from a hard disk drive included in a created RAID set, copy
first the RAID driver from the support DVD to a floppy disk before you install an operating
system to the selected hard disk drive.
5-2
Chapter 5: RAID Configuration
5.1.2
Installing hard disk drives
The motherboard supports Serial ATA for RAID set configuration. For optimal performance,
install identical drives of the same model and capacity when creating a disk array.
To install the SATA hard disks for RAID configuration:
1.
2.
3.
Install the SATA hard disks into the drive bays following the instructions in the system
user guide.
Connect a SATA signal cable to the signal connector at the back of each drive and to
the SATA connector on the motherboard.
Connect a SATA power cable to the power connector on each drive.
5.1.3
Setting the RAID item in BIOS
You must set the RAID item in the BIOS Setup before you can create a RAID set from SATA
hard disk drives attached to the SATA connectors supported by Intel® C621 chipset.
To do this:
1.
2.
3.
4.
Enter the BIOS Setup during POST.
Go to the Platform Configuration Menu > PCH Configuration, then press <Enter>.
Set Configure SATA as to [RAID Mode].
Press <F10> to save your changes and exit the BIOS Setup.
Refer to Chapter 4 for details on entering and navigating through the BIOS Setup.
5-3
Z11PA-D8C Series
5.2
Intel® Rapid Storage Technology enterprise SATA
Option ROM Utility
The Intel® Rapid Storage Technology enterprise SATA Option ROM utility allows you to
create RAID 0, RAID 1, RAID 10 (RAID 1+0), and RAID 5 set from Serial ATA hard disk
drives that are connected to the Serial ATA connectors supported by the Southbridge.
Before you proceed, ensure that you have installed the Serial ATA hard disk drives, and
have set the correct SATA mode in the BIOS setup.
To launch the Intel® Rapid Storage Technology enterprise SATA Option ROM utility:
1.
2.
Turn on the system.
During POST, press <Ctrl>+<I> to display the utility main menu.
Intel(R) Rapid Storage Technology enterprise - SATA Option ROM - 3.6.0.1023
Copyright(C) 2003-12 Intel Corporation. All Rights Reserved.
[ MAIN MENU ]
1. Create RAID Volume
2. Delete RAID Volume
3. Reset Disks to Non-RAID
4. Exit
[ DISK/VOLUME INFORMATION]
RAID Volumes:
None defined.
Physical Disks:
ID Drive Model
Serial #
HWAS0000991753TR
37VN00009846RAJ1
397600009846UEDY
GWC50000991756G6
Size
279.3GB
279.3GB
279.3GB
279.3GB
Type/Status(Vol ID)
Non-RAID Disk
Non-RAID Disk
Non-RAID Disk
Non-RAID Disk
0
1
2
3
ST3300656SS
ST3300656SS
ST3300656SS
ST3300656SS
[
]-Select
[ESC]-Exit
[ENTER]-Select Menu
The navigation keys at the bottom of the screen allow you to move through the menus
and select the menu options.
The RAID BIOS setup screens shown in this section are for reference only and may not
exactly match the items on your screen.
5-4
Chapter 5: RAID Configuration
5.2.1
Creating a RAID set
To create a RAID set:
1.
2.
From the utility main menu, select 1. Create RAID Volume and press <Enter>.
Key in a name for the RAID set and press <Enter>.
Intel(R) Rapid Storage Technology enterprise - SATA Option ROM - 3.6.0.1023
Copyright(C) 2003-12 Intel Corporation. All Rights Reserved.
[ CREATE VOLUME MENU ]
Name: Volume0
RAID Level: RAID0(Strips)
Disks: Select Disks
Strip Size: 128KB
Capacity: 0.0 GB
Syne: N/A
Create Volume
[ HELP ]
Enter a unique volume name that has no special characters and is
16 characters or less.
[
]Change
[TAB]-Next
[ESC]-Previous Menu
[ENTER]-Select
3.
4.
Press the up/down arrow keys to select a RAID Level that you wish to create then
press <Enter>.
From the Disks item field, press <Enter> to select the hard disk drives that you want to
include in the RAID set.
[ SELECT DISKS ]
Port Drive Model
Serial #
Size
Status
0
1
2
3
ST3300656SS
ST3300656SS
ST3300656SS
ST3300656SS
HWAS0000991753TR
37VN00009846RAJ1
397600009846UEDY
GWC50000991756G6
279.3GB
279.3GB
279.3GB
279.3GB
Non-RAID Disk
Non-RAID Disk
Non-RAID Disk
Non-RAID Disk
Select 1 Master and 1 Recovery disk to create volume.
]-Prev/Next [TAB]-(M)aster [SPACE]-(R)ecovery [ENTER]-Done
[
5.
Use the up/down arrow keys to move the selection bar then press <Space> to select a
disk. A small triangle before the Port number marks the selected drive. Press <Enter>
when you are done.
5-5
Z11PA-D8C Series
6.
Use the up/down arrow keys to select the stripe size for the RAID array (for RAID 0,
10 and 5 only) then press <Enter>. The available stripe size values range from 4 KB to
128 KB. The following are typical values:
RAID 0:
RAID 10:
RAID 5:
128KB
64KB
64KB
We recommend a lower stripe size for server systems, and a higher stripe size for
multimedia computer systems used mainly for audio and video editing.
7.
In the Capacity field item, key in the RAID volume capacity that you want to use and
press <Enter>. The default value field indicates the maximum allowed capacity.
8.
9.
Press <Enter> to start creating the RAID volume.
From the following warning message, press <Y> to create the RAID volume and return
to the main menu, or press <N> to go back to the CREATE VOLUME menu.
WARNING: ALL DATA ON SELECTED DISKS WILL BE LOST.
Are you sure you want to create this volume? (Y/N):
5-6
Chapter 5: RAID Configuration
5.2.2
Deleting a RAID set
Take caution when deleting a RAID set. You will lose all data on the hard disk drives when
you delete a RAID set.
To delete a RAID set:
1.
2.
From the utility main menu, select 2. Delete RAID Volume and press <Enter>.
From the Delete Volume Menu, press the up/down arrow keys to select the RAID set
you want to delete then press <Del>.
Intel(R) Rapid Storage Technology enterprise - SATA Option ROM - 3.6.0.1023
Copyright(C) 2003-12 Intel Corporation. All Rights Reserved.
[ DELETE VOLUME MENU ]
Name
Volume0
Level
RAID0(Stripe)
Drives
2
Capacity
298.0GB
Status
Normal
Bootable
Yes
[ HELP ]
Deleting a volume will reset the disks to non-RAID
WARNING: ALL DISK DATA WILL BE DELETED.
(This does not apply to Recovery volumes)
[
]-Select
[ESC]-Previous Menu
[DEL]-Delete Volume
3.
Press <Y> to confirm deletion of the selected RAID set and return to the utility main
menu, or press <N> to return to the DELETE VOLUME menu.
[ DELETE VOLUME VERIFICATION ]
ALL DATA IN THE VOLUME WILL BE LOST!
(This does not apply to Recovery volumes)
Are you sure you want to delete volume “Volume0”? (Y/N):
5-7
Z11PA-D8C Series
5.2.3
Resetting disks to Non-RAID
Take caution before you reset a RAID volume hard disk drive to non-RAID. Resetting a
RAID volume hard disk drive deletes all internal RAID structure on the drive.
To reset a RAID set:
1.
2.
From the utility main menu, select 3. Reset Disks to Non-RAID and press <Enter>.
Press the up/down arrow keys to select the drive(s) or disks of the RAID set you want
to reset, then press <Space>. A small triangle before the Port number marks the
selected drive. Press <Enter> when you are done.
[ RESET RAID DATA ]
Resetting RAID disk will remove its RAID structures
and revert it to a non-RAID disk.
WARNING: Resetting a disk causes all data on the disk to be lost.
(This does not apply to Recovery volumes)
Port Drive Model
Serial #
HWAS0000991753TR
37VN00009846RAJ1
Size
279.3GB
279.3GB
Status
Member Disk
Member Disk
0
1
ST3300656SS
ST3300656SS
Select the disks that should be reset.
]-Previous/Next [SPACE]-Selects [ENTER]-Selection Complete
[
3.
Press <Y> in the confirmation window to reset the drive(s) or press <N> to return to the
utility main menu.
5-8
Chapter 5: RAID Configuration
5.2.4
Exiting the Intel® Rapid Storage Technology enterprise
SATA Option ROM utility
To exit the utility:
1.
2.
From the utility main menu, select 4. Exit then press <Enter>.
Press <Y> to exit or press <N> to return to the utility main menu.
[ CONFIRM EXIT ]
Are you sure you want to exit? (Y/N):
5.2.5
Rebuilding the RAID
This option is only for the RAID 1 set.
Rebuilding the RAID with other non-RAID disk
If any of the SATA hard disk drives included in the RAID 1 array failed, the system displays
the status of the RAID volume as “Degraded” during POST. You can rebuild the RAID array
with other installed non-RAID disks.
To rebuild the RAID with other non-RAID disk:
1.
During POST, press <Ctrl>+<I> at the prompt to enter the Intel Rapid Storage
Technology option ROM utility.
2.
If there is a non-RAID SATA Hard Disk available, the utility will prompt you to rebuild
the RAID. Press the up/down arrow keys to select the destination disk then Press
<Enter> to start the rebuilding process, or press <ESC> to exit.
[ DEGRADED VOLUME DETECTED ]
“Degraded” volume and disk available for rebuilding detected. Selectign
a disk initiates a rebuild. Rebuild completes in the operating system.
Select the port of destination disk for rebuilding (ESC to exit):
Port Drive Model
XXXXXXXXXXX
Serial #
XXXXXXXX
Size
XXX.GB
X
[
]-Previous/Next [ENTER]-Select [ESC]-Exit
Select a destination disk with the same size as the original hard disk.
5-9
Z11PA-D8C Series
3.
The utility immediately starts rebuilding after the disk is selected. When done, the
status of the degraded RAID volume is changed to “Rebuild”.
Intel(R) Rapid Storage Technology enterprise - SATA Option ROM - 3.6.0.1023
Copyright(C) 2003-12 Intel Corporation. All Rights Reserved.
[ MAIN MENU ]
1. Create RAID Volume
2. Delete RAID Volume
3. Reset Disks to Non-RAID
4. Exit
[ DISK/VOLUME INFORMATION]
RAID Volumes:
*=Data is Encrypted
ID
1
Name
Level1
RAID1(Mirror)
Strip
N/A
Size
149.0GB
Status
Bootable
Yes
Volume0
Rebuild
Physical Devices:
Port Drive Model
Serial #
9LS0F4HL
3LS0JYL8
Size
Type/Status(Vol ID)
Member Disk(0)
Member Disk(0)
1
2
ST3160812AS
ST3160812AS
149.0GB
149.0GB
Volumes with “Rebuild” status will be rebuilt within the operating system.
[
]-Select
[ESC]-Exit
[ENTER]-Select Menu
4.
5.
Press <Esc> to exit Intel Rapid Storage Technology and reboot the system.
Select Start > Programs > Intel Rapid Storage > Intel Rapid Storage Console or
click the Intel Rapid Storage Technology tray icon to load the Intel Rapid Storage
Manager utility.
6.
7.
From the View menu, select Advanced Mode to display the details of the Intel Rapid
Storage Console.
From the Volumes view option, select RAID volume to view the rebuilding status.
When finished, the status is changed to “Normal”.
Rebuilding the RAID with a new hard disk
If any of the SATA hard disk drives included in the RAID array failed, the system displays the
status of the RAID volume as “Degraded” during POST. You may replace the disk drive and
rebuild the RAID array.
To rebuild the RAID with a new hard disk:
1.
Remove the failed SATA hard disk and install a new SATA hard disk of the same
specification into the same SATA Port.
Select a destination disk with the same size as the original hard disk.
2.
Reboot the system then follow the steps in section Rebuilding the RAID with other
non-RAID disk.
5-10
Chapter 5: RAID Configuration
5.2.6
Setting the Boot array in the BIOS Setup Utility
You can set the boot priority sequence in the BIOS for your RAID arrays when creating multi-
RAID using the Intel® Rapid Storage Technology enterprise SATA Option ROM utility.
To set the boot array in the BIOS:
Set at least one of the arrays bootable to boot from the hard disk.
1.
2.
3.
Reboot the system and press <Del> to enter the BIOS setup utility during POST.
Go to the Boot menu and select the boot option priority.
Use up/down arrow keys to select the boot priority and press <Enter>. See the Boot
menu section of Chapter 4 for more details.
4.
5.
From the Exit menu, select Save Changes & Exit, then press <Enter>.
When the confirmation window appears, select Yes, then press <Enter>.
5-11
Z11PA-D8C Series
5.3
Intel® Rapid Storage Technology enterprise
(Windows)
The Intel® Rapid Storage Technology enterprise allows you to create RAID 0, RAID 1, RAID
10 (RAID 1+0), and RAID 5 set(s) from Serial ATA hard disk drives that are connected to the
Serial ATA connectors supported by the Southbridge.
You need to manually install the Intel® Rapid Storage Technology enterprise utility on a
Windows® operating system. Please refer to the installation instructions in Chapter 6.
To enter the Intel® Rapid Storage Technology enterprise utility under Windows operating
system:
1.
2.
Turn on the system and go to the windows desktop.
Click the Intel® Rapid Storage Technology enterprise icon to display the main menu.
Your storage system is configured for data protection, increased performance and
optimal data storage capacity. You can create additional volumes to further optimize
your storage system.
You can click Rescan to re-scan any attached hard disks.
5-12
Chapter 5: RAID Configuration
5.3.1
Creating a RAID set
To create a RAID set:
1.
2.
From the utility main menu, select Create Volume and select volume type.
Click Next.
3.
4.
5.
Enter a name for the RAID set, then select the array disks.
Select Volume Size tab, you can drag the bar to decide the volume size.
Click Next.
•
•
If you do not want to keep the data on one of the selected disks, select NO when
prompted.
If you want to Enable volume write-back cache or Initialize volume, click
Advanced.
5-13
Z11PA-D8C Series
6.
Confirm the volume creation, than click Create Volume to continue.
This process could take a while depending on the number and size of the disks. You can
continue using other applications during this time.
7.
Wait until the process is completed, then click OK when prompted.
You still need to partition your new volume using Windows Disk Management before
adding any data.
The RAID set is displayed in the Volumes list and you can change the settings in
Volume Properties.
5-14
Chapter 5: RAID Configuration
5.3.2
Changing a Volume Type
To change the volume type in Volume Properties:
1.
2.
Click the SATA array items you want to change in Volumes field.
From the Volume Properties field, select Type:RAID 1 Change type.
3.
4.
You can change the Name, Select the new volume type, and Select additional
disks to include in the new volume if needed.
Select the Data stripe size for the RAID array (for RAID 0, 10 and 5 only), and click
OK. The available stripe size values range from 4 KB to 128 KB. The following are
typical values:
RAID 0:
RAID 10:
RAID 5:
128KB
64KB
64KB
We recommend a lower stripe size for server systems, and a higher stripe size for
multimedia computer systems used mainly for audio and video editing.
5-15
Z11PA-D8C Series
5.3.3
Deleting a volume
Be cautious when deleting a volume. You will lose all data on the hard disk drives. Before
you proceed, ensure that you back up all your important data from your hard drives.
To delete a volume:
1.
From the utility main menu, select the volume (exp. Volume_0000) in Volumes field
you want to delete.
2.
Select Delete volume in Volume Properties field. The following screen appears.
3.
Click Yes to delete the volume and return to the utility main menu, or click No to return
to the main menu.
5-16
Chapter 5: RAID Configuration
5.3.4
Preferences
System Preferences
Allow you to set to show the notification area icon and show system information, warning, or
errors here.
E-Mail Preferences
Allow you to set to sent e-mail of the following events:
•
•
•
Storage system information
Storage system warnings
Storage system errors
5-17
Z11PA-D8C Series
5.4
Intel® Virtual Raid on CPU in BIOS
This feature requires a KEY module to enable CPU RAID functions with Intel® CPU RSTe.
•
•
The KEY module is purchased separately.
Refer to section 2.8.2 Internal connectors for the location of the VROC_HW_KEY
connector.
Due to hardware design, your motherboard does not support CPU RAID configurations as
OS drives.
To enter the Intel® Virtual Raid on CPU in BIOS:
1.
2.
Enter the BIOS Setup during POST.
Go to the Advanced menu > Intel(R) Virtual Raid on CPU > All Intel VMD
Controllers then press <Enter> to display the Intel® Virtual Raid on CPU menu.
Refer to Chapter 4 for details on entering and navigating through the BIOS Setup.
Due to chipset limitation, when SATA ports are set to RAID mode, all SATA ports run at
RAID mode together.
5-18
Chapter 5: RAID Configuration
5.4.1
Creating a RAID set
To create a RAID set:
1.
From the Intel® Virtual Raid on CPU menu, select Create RAID Volume and press
<Enter>. The following screen appears:
2.
3.
When the Name item is selected, enter a name for the RAID set and press <Enter>.
When the RAID Level item is selected, press <Enter> to select the RAID level to
create, and then press <Enter>.
4.
5.
6.
When the Enable RAID spanned over VMD Controllers item is selected, press
<Enter> and select X to enable this function.
Under Select Disks, press <Enter> and select X for the disks you want to include in the
RAID set.
When the Strip Size item is selected, press <Enter> to select strip size for the RAID
array (for RAID 0, 10 and 5 only), and then press <Enter>. The available strip size
values range from 4 KB to 128 KB. The following are typical values:
-
-
-
RAID 0: 128 KB
RAID 10: 64 KB
RAID 5: 64 KB
We recommend a lower strip size for server systems, and a higher strip size for multimedia
computer systems used mainly for audio and video editing.
5-19
Z11PA-D8C Series
7.
8.
When the Capacity (MB) item is selected, enter the RAID volume capacity that you
want and press <Enter>. The default value indicates the maximum allowed capacity.
When the Create Volume item is selected, press <Enter> to create the RAID volume
and return to the Intel® Rapid Storage Technology menu.
5-20
Chapter 5: RAID Configuration
5.4.2
Deleting a RAID set
Be cautious when deleting a RAID set. You will lose all data on the hard disk drives when
you delete a RAID set.
To delete a RAID set:
1.
From the Intel® Virtual Raid on CPU menu, select the RAID volume you want to delete
and press <Enter>. The following screen appears:
2.
When the Delete item is selected, press <Enter>, then select Yes to delete the RAID
volume and return to the Intel® Virtual Raid on CPU menu, or select No to cancel.
5-21
Z11PA-D8C Series
5.4.3
Installing the RAID controller driver during Windows®
10 OS installation
This part provides the instructions on how to install the RAID controller drivers during OS
installation.
To install the RAID controller driver when installing Windows® 10 OS:
1.
Boot the computer using the Windows® 10 OS installation disc. Follow the screen
instructions to start installing Windows® 10.
2.
When prompted to choose a type of installation, click Custom: Install Windows only
(advanced).
3.
Click Load Driver.
5-22
Chapter 5: RAID Configuration
4.
A message appears, reminding you to insert the installation media containing the driver
of the RAID controller driver. If you have only one optical drive installed in your system,
eject the Windows OS installation disc and replace with the motherboard Support DVD
into the optical drive. Click Browse to continue.
5.
Locate the driver in the corresponding folder of the support DVD then click OK to
continue.
6.
7.
Select the RAID controller driver you need from the list and click Next.
When the system finishes loading the RAID driver, replace the motherboard Support
DVD with the Windows Server installation disc. Select the drive to install Windows and
click Next.
8.
Setup then proceeds with the OS installation. Follow screen instructions to continue.
5-23
Z11PA-D8C Series
5-24
Chapter 5: RAID Configuration
6.1
RAID driver installation
After creating the RAID sets for your server system, you are now ready to install an
operating system to the independent hard disk drive or bootable array. This part provides the
instructions on how to install the RAID controller drivers during OS installation.
6.1.1
Creating a USB flash drive with RAID drive
When installing Windows® Server OS, you can load the RAID driver from a USB flash drive.
You can create a USB flash drive with RAID driver in Windows by copying the files from the
support DVD to the USB flash drive.
To copy the RAID driver to a USB flash drive in Windows environment:
1.
2.
3.
4.
Place the motherboard support DVD in the optical drive.
Connect a USB flash drive to your system.
Click on the optical drive to browse the contents of the support DVD.
Click Drivers > C620 INTEL RAID > Windows > Driver and then copy the RAID driver
folder to the USB flash drive.
6.1.2
Installing the RAID controller driver
During Windows® Server 2012 R2 or 2016 OS installation
To install the RAID controller driver when installing Windows® Server OS:
1.
Boot the computer using the Windows® Server installation disc. Follow the onscreen
instructions to start installing Windows® Server.
2.
When prompted to choose a type of installation, click Custom: Install Windows only
(advanced).
6-2
Chapter 6: Driver Installation
3.
Click Load Driver.
4.
A message appears reminding you to insert the installation media containing the driver of
the RAID controller driver (the installation media can be a CD, DVD, or USB flash drive).
•
If you have only one optical drive installed in your system, eject the Windows OS
installation disc and replace with the motherboard Support DVD into the optical
drive.
•
Or y
ou may connect a USB flash drive containing the RAID controller driver.
Click Browse to continue.
5.
Locate the driver in the corresponding folder of the Support DVD or USB flash drive
and then click OK to continue.
6.
Select the RAID controller driver you need from the list and click Next.
Z11PA-D8C Series
6-3
7.
When the system finishes loading the RAID driver,
•
Replace the motherboard Support DVD with the Windows Server installation disc.
•
Remove the USB flash drive.
Select the drive to install Windows and click Next.
8.
Setup then proceeds with the OS installation. Follow the onscreen instructions to
continue.
6-4
Chapter 6: Driver Installation
6.2
Management applications and utilities installation
The support DVD that is bundled with your motherboard contains drivers, management
applications, and utilities that you can install to maximize the features of your motherboard.
•
The contents of the support DVD are subject to change at any time without notice.
Visit the ASUS website (www.asus.com) for the latest updates on software and
utilities.
•
The support DVD is supported on Windows® Server 2012 R2 and Windows® Server
2016.
6.3
Running the Support DVD
When you place the support DVD into the optical drive, the DVD automatically displays the
main screen if Autorun is enabled in your computer. By default, the Drivers tab is displayed.
If Autorun is NOT enabled in your computer, browse the contents of the support DVD to
locate the file ASSETUP.EXE from the BIN folder. Double-click the ASSETUP.EXE to run
the support DVD.
The main screen of the Support DVD contains the following tabs:
1.
2.
3.
4.
Drivers
Utilities
Manual
Contact
•
•
The main screen of the Support DVD looks exactly the same on the Windows® Server
2012 R2 and on the Windows® Server 2016 Operating System (OS).
Onscreen display and content vary depending on the motherboard and chipset. The
screenshots are provided for reference only.
Z11PA-D8C Series
6-5
6.3.1
Drivers menu tab
The Drivers Menu shows the available device drivers if the system detects installed devices.
Install the necessary drivers to activate the devices.
6.3.2
Utilities menu tab
The Utilities menu displays the software applications and utilities that the motherboard supports.
6-6
Chapter 6: Driver Installation
6.3.3
Manual menu
The Manual menu provides a list of supplementary user guides.
You need an internet browser installed in your OS to view the User Guide.
6.3.4
Contact information menu
The Contact menu displays the ASUS contact information, e-mail addresses, and useful links
if you need more information or technical support for your motherboard.
Z11PA-D8C Series
6-7
6.4
Intel® chipset device software installation
This section provides the instructions on how to install the Intel® chipset device software on
the system.
You need to manually install the Intel® chipset device software on a Windows operating
system.
To install the Intel® chipset device software:
1.
2.
Restart the computer, and then log on with Administrator privileges.
Insert the motherboard/system support DVD into the optical drive. The support DVD
automatically displays the Drivers menu if Autorun is enabled in your computer.
If Autorun is NOT enabled in your computer, browse the contents of the support DVD to
locate the file ASSETUP.EXE from the BIN folder. Double-click the ASSETUP.EXE to run
the support DVD.
3.
Click the item Intel® Chipset Device Software from the menu.
4.
The Intel® Chipset Device Software window appears. Click Next to start the
installation.
6-8
Chapter 6: Driver Installation
5.
Read the License Agreement and click Accept to continue the process.
6.
Read the Readme File Information and click Install to start the installation process.
7.
Click Restart Now to complete the setup process.
Z11PA-D8C Series
6-9
6.5
Installing the Intel® I210 Gigabit Adapters driver
This section provides the instructions on how to install the Intel® I210 Gigabits Adapter
Driver on the system.
To install the Intel® I210 Gigabit Adapters Driver on the Windows® operating system:
1.
2.
3.
Restart the computer.
Log on with Administrator privileges.
Insert the motherboard/system support DVD to the optical drive.
If Autorun is NOT enabled in your computer, browse the contents of the support DVD to
locate the file ASSETUP.EXE from the BIN folder. Double-click the ASSETUP.EXE to run
the support DVD.
4.
Click Intel® I350-AM2/I210 Gigabit Adapters Driver in the Drivers menu of the main
screen to start the installation.
5.
Click Install Drivers and Software option to begin installation.
6-10
Chapter 6: Driver Installation
6.
Click Next when the Intel(R) Network Connections Install Wizard window appears.
7.
Tick I accept the terms in the license agreement and click Next to continue.
8.
From the Setup Options window, click Next to start the installation.
By default, Intel(R) PROSet for Windows Device Manager and Windows PowerShell
Module are ticked.
Z11PA-D8C Series
6-11
9.
Click Install to start the installation.
10. When the installation is done, press Finish to complete the installation.
6-12
Chapter 6: Driver Installation
6.6
VGA driver installation
This section provides the instructions on how to install the ASPEED Video Graphics Adapter
(VGA) driver.
You need to manually install the ASPEED VGA driver on a Windows® operating system.
To install the ASPEED VGA driver:
1.
2.
Restart the computer, and then log on with Administrator privileges.
Insert the motherboard/system support DVD into the optical drive. The support DVD
automatically displays the Drivers menu if Autorun is enabled in your computer.
If Autorun is NOT enabled in your computer, browse the contents of the support DVD to
locate the file ASSETUP.EXE from the BIN folder. Double-click the ASSETUP.EXE to run
the support DVD.
3.
Click the ASPEED AST2500 Display Driver to begin installation.
4.
From the installation window, click Next to start the installation.
Z11PA-D8C Series
6-13
5.
Click Install to start the installation process.
6.
Click Finish to complete the installation.
6-14
Chapter 6: Driver Installation
6.7
Intel® Rapid Storage Technology enterprise 5.0
installation
This section provides the instructions on how to install the Intel® Rapid Storage Technology
enterprise 5.0 on the system.
You need to manually install the Intel® Rapid Storage Technology enterprise 5.0 utility on a
Windows® operating system.
To install the Intel® Rapid Storage Technology enterprise 5.0 utility:
1.
2.
Restart the computer, and then log on with Administrator privileges.
Insert the motherboard/system support DVD into the optical drive, and navigate to the
Utilities menu.
3.
Click the Intel® Rapid Storage Technology enterprise to begin installation.
4.
The Intel® Rapid Storage Technology enterprise window appears. Click Next to start
the installation.
Z11PA-D8C Series
6-15
5.
Read the Warning message and click Next to continue.
6.
Read the License Agreement and click Accept to continue the process.
7.
Select the destination folder and click Next to continue.
6-16
Chapter 6: Driver Installation
8.
Tick the features that you would like to install and click Next to continue.
9.
Click Install to start the installation process.
10. Click Restart Now to complete the setup process.
Z11PA-D8C Series
6-17
6-18
Chapter 6: Driver Installation
Q-Code table
Action
PHASE
POST CODE
01
TYPE
DESCRIPTION
Progress
First post code(POWER_ON_POST_CODE)
Load BSP microcode(MICROCODE_POST_CODE)
Set cache as ram for PEI phase(CACHE_ENABLED_POST_CODE)
CPU Early init.(CPU_EARLY_INIT_POST_CODE)
initializes South bridge for PEI preparation
PEI Core Entry
02
Progress
03
Progress
Security Phase
06
Progress
04
Progress
10
Progress
15
Progress
NB initialize before installed memory
SB initialize before installed memory
Wait BMC ready(duration: 120 seconds)
QPI initialization
19
Progress
78~00
A1
Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
Progress
A3
QPI initialization
A7
QPI initialization
A8
QPI initialization
A9
QPI initialization
AA
AB
AC
AD
AE
AF
2F
QPI initialization
QPI initialization
QPI initialization
QPI initialization
QPI initialization
QPI initialization Complete
Memory Init.
Normal boot
B0
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
Progress
Memory Init.
B1
Memory Init.
PEI (Pre-EFI
initialization) phase
AF
B4
RC Reset if require
Memory Init.
B2
Memory Init.
B3
Memory Init.
B5
Memory Init.
B6
Memory Init.
B7
Memory Init.
B8
Memory Init.
B9
Memory Init.
BA
BB
BC
BF
5A
Memory Init.
Memory Init.
Memory Init.
Memory Init. Done
Other config. After RC end
Memory already installed
CPU Init.
31
32
Progress
34
Progress
CPU Init.
36
Progress
CPU Init.
4F
Progress
DXE Initial Program Load(IPL)
(continued on the next page)
A-3
Z11PA-D8C Series
Q-Code table
Action
PHASE
POST CODE
60
TYPE
DESCRIPTION
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
DXE Core Started
DXE NVRAM Init.
SB run-time init.
DXE CPU Init
61
62
63
68
NB Init.
DXE (Driver
69
NB Init.
Execution
6A
70
NB Init.
Environment) phase
SB Init.
71
SB Init.
72
SB Init.
78
ACPI Init.
79
CSM Init.
90
BDS started
91
Connect device event
PCI Bus Enumeration.
PCI Bus Enumeration.
PCI Bus Enumeration.
PCI Bus Enumeration.
PCI Bus Enumeration.
Console outout connect event
Console input connect event
AMI Super IO start
AMI USB Driver Init.
AMI USB Driver Init.
AMI USB Driver Init.
AMI USB Driver Init.
Legacy Option ROM Init.
Reset system
92
93
94
95
96
97
98
Normal boot
99
9A
9B
9C
9D
b2
BDS (Boot Device
Selection) phase
b3
b4
USB hotplug
b6
NVRAM clean up
NVRAM configuration reset
IDE, AHCI Init.
b7
A0
A1
A2
A3
A8
A9
AB
AD
AE
AA
AC
IDE, AHCI Init.
IDE, AHCI Init.
IDE, AHCI Init.
BIOS Setup Utility password verify
BIOS Setup Utility start
BIOS Setup Utility input wait
Ready to boot event
Legacy boot event
APIC mode
Operating system
phase
PIC mode
A-4
Appendix
Simplified EU Declaration of Conformity
Română ASUSTeK Computer Inc. declară că acest dispozitiv se conformează
English ASUSTeK Computer Inc. hereby declares that this device is in
compliance with the essential requirements and other relevant provisions
of related Directives. Full text of EU declaration of conformity is available at:
www.asus.com/support
cerinţelor esenţiale şi altor prevederi relevante ale directivelor conexe. Textul
complet al declaraţiei de conformitate a Uniunii Europene se găseşte la:
www.asus.com/support
Srpski ASUSTeK Computer Inc. ovim izjavljuje da je ovaj uređaj u saglasnosti
Français AsusTek Computer Inc. déclare par la présente que cet appareil est
conforme aux critères essentiels et autres clauses pertinentes des directives
concernées. La déclaration de conformité de l’UE peut être téléchargée à
partir du site Internet suivant : www.asus.com/support
sa osnovnim zahtevima drugim relevantnim odredbama povezanih
i
Direktiva. Pun tekst EU deklaracije o usaglašenosti je dostupan da adresi:
www.asus.com/support
Slovensky Spoločnosť ASUSTeK Computer Inc. týmto vyhlasuje, že toto
Deutsch ASUSTeK Computer Inc. erklärt hiermit, dass dieses Gerät mit
den wesentlichen Anforderungen und anderen relevanten Bestimmungen
der zugehörigen Richtlinien übereinstimmt. Der gesamte Text der EU-
Konformitätserklärung ist verfügbar unter: www.asus.com/support
zariadenie vyhovuje základným požiadavkám
a
ostatým príslušným
ustanoveniam príslušných smerníc. Celý text vyhlásenia o zhode pre štáty EÚ
je dostupný na adrese: www.asus.com/support
Slovenščina ASUSTeK Computer Inc. izjavlja, da je ta naprava skladna z
bistvenimi zahtevami in drugimi ustreznimi določbami povezanih direktiv.
Celotno besedilo EU-izjave o skladnosti je na voljo na spletnem mestu:
www.asus.com/support
Italiano ASUSTeK Computer Inc. con la presente dichiara che questo
dispositivo è conforme ai requisiti essenziali e alle altre disposizioni pertinenti
con le direttive correlate. Il testo completo della dichiarazione di conformità
UE è disponibile all’indirizzo: www.asus.com/support
Español Por la presente, ASUSTeK Computer Inc. declara que este dispositivo
cumple los requisitos básicos y otras disposiciones pertinentes de las
directivas relacionadas. El texto completo de la declaración de la UE de
conformidad está disponible en: www.asus.com/support
Русский Компания ASUS заявляет, что это устройство соответствует
основным требованиям
и
другим соответствующим условиям
соответствующих директив. Подробную информацию, пожалуйста,
смотрите на www.asus.com/support
Svensk a ASUSTeK Computer I nc. förk larar härmed att denna
enhet överensstämmer med de grundläggande kraven och andra
relevanta föreskrifter i relaterade direktiv. Fulltext av EU-försäkran om
överensstämmelse finns på: www.asus.com/support
Български
С
настоящото ASUSTeK Computer Inc. декларира, че
това устройство е в съответствие със съществените изисквания и
другите приложими постановления на свързаните директиви. Пълният
текст на декларацията за съответствие на ЕС е достъпна на адрес:
www.asus.com/support
Українська ASUSTeK Computer Inc. заявляє, що цей пристрій відповідає
основним вимогам та іншим відповідним положенням відповідних
Директив. Повний текст декларації відповідності стандартам ЄС
доступний на: www.asus.com/support
Hrvatski ASUSTeK Computer Inc. ovim izjavljuje da je ovaj uređaj sukladan
s bitnim zahtjevima i ostalim odgovarajućim odredbama vezanih direktiva.
Cijeli tekst EU izjave o sukladnosti dostupan je na: www.asus.com/support
Türkçe AsusTek Computer Inc., bu aygıtın temel gereksinimlerle ve
ilişkili Yönergelerin diğer ilgili koşullarıyla uyumlu olduğunu beyan
eder. AB uygunluk bildiriminin tam metni şu adreste bulunabilir:
www.asus.com/support
Čeština Společnost ASUSTeK Computer Inc. tímto prohlašuje, že toto
zařízení splňuje základní požadavky a další příslušná ustanovení souvisejících
směrnic. Plné znění prohlášení
www.asus.com/support
o
shodě EU je
k
dispozici na adrese:
Bosanski ASUSTeK Computer Inc. ovim izjavljuje da je ovaj uređaj usklađen
sa bitnim zahtjevima i ostalim odgovarajućim odredbama vezanih direktiva.
Cijeli tekst EU izjave o usklađenosti dostupan je na: www.asus.com/support
Dansk ASUSTeK Computer Inc. erklærer hermed, at denne enhed er i
overensstemmelse med hovedkravene og andre relevante bestemmelser i de
relaterede direktiver. Hele EU-overensstemmelseserklæringen kan findes på:
www.asus.com/support
Nederlands ASUSTeK Computer Inc. verklaart hierbij dat dit apparaat
voldoet aan de essentiële vereisten en andere relevante bepalingen van de
verwante richtlijnen. De volledige tekst van de EU-verklaring van conformiteit
is beschikbaar op: www.asus.com/support
Eesti Käesolevaga kinnitab ASUSTeK Computer Inc, et see seade vastab
asjakohaste direktiivide oluliste nõuetele ja teistele asjassepuutuvatele
sätetele. EL vastavusdeklaratsiooni täielik tekst on saadaval järgmisel
aadressil: www.asus.com/support
Suomi ASUSTeK Computer Inc. ilmoittaa täten, että tämä laite on
asiaankuuluvien direktiivien olennaisten vaatimusten ja muiden tätä
koskevien säädösten mukainen. EU-yhdenmukaisuusilmoituksen koko teksti
on luettavissa osoitteessa: www.asus.com/support
Ελληνικά Με το παρόν, η AsusTek Computer Inc. δηλώνει ότι αυτή η συσκευή
συμμορφώνεται με τις θεμελιώδεις απαιτήσεις και άλλες σχετικές διατάξεις
των Οδηγιών της ΕΕ. Το πλήρες κείμενο της δήλωσης συμβατότητας είναι
διαθέσιμο στη διεύθυνση: www.asus.com/support
Magyar Az ASUSTeK Computer Inc. ezennel kijelenti, hogy ez az eszköz
megfelel a kapcsolódó Irányelvek lényeges követelményeinek és egyéb
vonatkozó rendelkezéseinek. Az EU megfelelőségi nyilatkozat teljes szövege
innen letölthető: www.asus.com/support
Latviski ASUSTeK Computer Inc. ar šo paziņo, ka šī ierīce atbilst saistīto
Direktīvu būtiskajām prasībām un citiem citiem saistošajiem nosacījumiem.
Pilns ES atbilstības paziņojuma teksts pieejams šeit: www.asus.com/support
Lietuvių „ASUSTeK Computer Inc.“ šiuo tvirtina, kad šis įrenginys atitinka
pagrindinius reikalavimus ir kitas svarbias susijusių direktyvų nuostatas. Visą
ES atitikties deklaracijos tekstą galima rasti: www.asus.com/support
Norsk ASUSTeK Computer Inc. erklærer herved at denne enheten er i
samsvar med hovedsaklige krav og andre relevante forskrifter i relaterte
direktiver. Fullstendig tekst for EU-samsvarserklæringen finnes på:
www.asus.com/support
Polski Firma ASUSTeK Computer Inc. niniejszym oświadcza, że urządzenie to
jest zgodne z zasadniczymi wymogami i innymi właściwymi postanowieniami
powiązanych dyrektyw. Pełny tekst deklaracji zgodności UE jest dostępny pod
adresem: www.asus.com/support
Português A ASUSTeK Computer Inc. declara que este dispositivo está em
conformidade com os requisitos essenciais e outras disposições relevantes
das Diretivas relacionadas. Texto integral da declaração da UE disponível em:
www.asus.com/support
A-5
Z11PA-D8C Series
ASUS contact information
ASUSTeK COMPUTER INC.
Address
Telephone
Fax
4F, No. 150, Li-Te Rd., Peitou, Taipei 112, Taiwan
+886-2-2894-3447
+886-2-2890-7798
Web site
Technical Support
Telephone
+86-21-38429911
Fax
+86-21-58668722 ext: 9101
Online Support
ASUSTeK COMPUTER INC. (Taiwan)
Address
Telephone
Fax
4F, No. 150, Li-Te Rd., Peitou, Taipei 112, Taiwan
+886-2-2894-3447
+886-2-2890-7798
Web site
Technical Support
Telephone
+886-2-2894-3447 (0800-093-456)
Online Support
ASUSTeK COMPUTER INC. (China)
Address
Telephone
Fax
No. 5077, Jindu Road, Minhang District, Shanghai, China
+86-21-5442-1616
+86-21-5442-0099
Web site
Technical Support
Telephone
+86-20-2804-7506 (400-620-6655)
Online Support
A-6
Appendix
ASUS contact information
ASUS COMPUTER INTERNATIONAL (America)
Address
Fax
48720 Kato Rd., Fremont, CA 94538, USA
+1-510-608-4555
Web site
Technical Support
Support fax
+1-812-284-0883
General support
Online support
+1-812-282-2787
ASUS COMPUTER GmbH (Germany and Austria)
Address
Fax
Harkort Str. 21-23, 40880 Ratingen, Germany
+49-2102-959911
Web site
Technical Support
Telephone
+49-1805-010923
Support Fax
+49-2102-959911
Online support
ASUS Czech Service s.r.o. (Europe)
Address
Na Rovince 887, 720 00 Ostrava – Hrabová,
Czech Republic
Telephone
+420-596766888
Web site
Technical Support
Telephone
+420-596-766-891
Fax
+420-596-766-329
E-mail
Online Support
A-7
Z11PA-D8C Series
ASUS contact information
ASUS Holland BV (The Netherlands)
Address
Marconistraat 2, 7825GD EMMEN, The Netherlands
Web site
Technical Support
Telephone
+31-(0)591-5-70292
Fax
+31-(0)591-666853
E-mail
Online Support
ASUS Polska Sp. z o.o. (Poland)
Address
Web site
Ul. Postępu 6, 02-676 Warszawa, Poland
Technical Support
Telephone
+48-225718033
Online Support
ASK-Service (Russia and CIS)
г.Москва, ул. Орджоникидзе, д.10, Россия
Address
Telephone
Web site
(495) 640-32-75
Technical Support
Telephone
Online Support
008-800-100-ASUS (008-800-100-2787)
A-8
Appendix
FCC COMPLIANCE INFORMATION
Per FCC Part 2 Section 2.1077(a)
Asus Computer International
800 Corporate Way, Fremont, CA 94539.
(510)739-3777/(510)608-4555
Responsible Party:
Address:
Phone/Fax No:
hereby declares that the product
Motherboard
Z11PA-D8, Z11PA-D8C
Product Name :
Model Number :
compliance statement:
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Ver. 180125
A-9
Z11PA-D8C Series
A-10
Appendix
|
