F225A
LF225A
OWNER’S MANUAL
U.S.A.Edition
LIT-18626-04-66
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01449
TO THE OWNER
Thank you for choosing a Yamaha outboard
motor. This Owner’s manual contains infor-
mation needed for proper operation, mainte-
nance and care. A thorough understanding
of these simple instructions will help you
obtain maximum enjoyment from your new
Yamaha. If you have any question about the
operation or maintenance of your outboard
motor, please consult a Yamaha dealer.
CAUTION:
A CAUTION indicates special precau-
tions that must be taken to avoid damage
to the outboard motor.
@
NOTE:
@
A NOTE provides key information to make
procedures easier or clearer.
@
* Yamaha continually seeks advancements
in product design and quality. Therefore,
while this manual contains the most cur-
rent product information available at the
time of printing, there may be minor dis-
crepancies between your machine and this
manual. If there is any question concern-
ing this manual, please consult your
Yamaha dealer.
In this Owner’s Manual particularly impor-
tant information is distinguished in the fol-
lowing ways.
The Safety Alert Symbol means
ATTENTION! BECOME ALERT!
YOUR SAFETY IS INVOLVED!
WARNING
Failure to follow WARNING instructions
could result in severe injury or death to
the machine operator, a bystander, or a
person inspecting or repairing the out-
NOTE:
@
@
The F225A, LF225A and their standard
accessories are used as a base for the
explanations and illustrations in this manual.
Therefore, some items may not apply to
every model.
board motor.
@
@
EMU01446
F225A/LF225A
OWNER’S MANUAL
©2001 by Yamaha Motor Corporation, USA
1st Edition, April 2001
All rights reserved.
Any reprinting or unauthorized use
without the written permission of
Yamaha Motor Corporation, USA
is expressly prohibited.
Printed in Japan
P/N LIT-18626-04-66
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
EMU00003
E
CONTENTS
GENERAL INFORMATION
1
2
3
4
5
6
BASIC COMPONENTS
OPERATION
MAINTENANCE
TROUBLE RECOVERY
INDEX
READ THIS OWNER’S MANUAL CAREFULLY
BEFORE OPERATING YOUR OUTBOARD MOTOR.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00004
Chapter 1
1
GENERAL
INFORMATION
IDENTIFICATION NUMBERS
RECORD .....................................................1-1
Outboard motor serial number ................1-1
Key number .............................................1-1
EMISSION CONTROL INFORMATION....1-2
North american models............................1-2
Star labels.................................................1-3
SAFETY INFORMATION ...........................1-4
IMPORTANT LABELS ...............................1-6
Warning labels .........................................1-6
BASIC BOATING RULES
(Rules of the road).....................................1-7
Steering and sailing rules and
sound signals ...........................................1-7
Rules when encountering vessels...........1-8
Other special situations............................1-9
FUELING INSTRUCTIONS......................1-11
Gasoline (petrol).....................................1-12
ENGINE OIL..............................................1-13
BATTERY REQUIREMENT.....................1-14
PROPELLER SELECTION......................1-15
START-IN-GEAR PROTECTION ............1-16
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00005
IDENTIFICATION NUMBERS
RECORD
EMU00007
OUTBOARD MOTOR SERIAL
NUMBER
The outboard motor serial number is
stamped on the label attached to the port
side of the clamp-bracket.
Record your outboard motor serial number
in the spaces provided to assist you in
ordering spare parts from your Yamaha
dealer or for reference in case your outboard
motor is stolen.
1 Outboard motor serial number
EMU00008
KEY NUMBER
If a main key switch is equipped with the
motor, the key identification number is
stamped on your key as shown in the illus-
tration. Record this number in the space
provided for reference in case you need a
new key.
1 Key number
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01385
EMISSION CONTROL
INFORMATION
EMU01444
NORTH AMERICAN MODELS
This engine conforms to U.S. Environmental
Protection Agency (EPA) regulations for
marine SI engines. See the label affixed to
your engine for details.
Approval label of Emission control certif-
icate
This label is attached to the bottom cowling.
1 Emission control information label
New Technology ; (4-stroke/HPDI) EM
Manufactured date label
This label is attached to the clamp bracket.
2 Manufactured date label
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01389
STAR LABELS
Your outboard motor is labeled with a Cali-
fornia Air Resources Board (CARB) star
label. See below for a description of your
particular label.
1 Star label
One Star - Low Emission
The one-star label identifies engines that
meet the Air Resources Board’s 2001
exhaust emission standards. Engines meet-
ing these standards have 75% lower emis-
sions than conventional carbureted two-
stroke engines. These engines are equiva-
lent to the U.S. EPA’s 2006 standards for
marine engines.
Two Stars - Very Low Emission
The two-star label identifies engines that
meet the Air Resources Board’s 2004
exhaust emission standards. Engines meet-
ing these standards have 20% lower emis-
sions than One Star-Low-Emission engines.
Three Stars - Ultra Low Emission
The three-star label identifies engines that
meet the Air Resources Board’s 2008
exhaust emission standards. Engines meet-
ing these standards have 65% lower emis-
sions than One Star-Low-Emission engines.
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00917
G This product emits exhaust gases which
contain carbon monoxide, a colorless,
odorless gas which may cause brain
damage or death when inhaled. Symp-
toms include nausea, dizziness, and
drowsiness. Keep cockpit and cabin
areas well ventilated. Avoid blocking
exhaust outlets.
SAFETY
INFORMATION
G Before mounting or operating the out-
board motor, read this entire manual.
Reading it should give you an under-
standing of the motor and its operation.
G Before operating the boat, read any
owner’s or operator’s manuals supplied
with it and all labels. Be sure you under-
stand each item before operating.
G Do not overpower the boat with this out-
board motor. Overpowering the boat
could result in loss of control. The rated
power of the outboard should be equal to
or less than the rated horsepower capac-
ity of the boat. If the rated horsepower
capacity of the boat is unknown, consult
the dealer or boat manufacturer.
G Do not modify the outboard. Modifications
could make the motor unfit or unsafe to
use.
G Never operate after drinking alcohol or
taking drugs. About 50% of all boating
fatalities involve intoxication.
G Have an approved personal flotation
device (PFD) on board for every occu-
pant. It is a good idea to wear a PFD
whenever boating. At a minimum, children
and non-swimmers should always wear
PFDs, and everyone should wear PFDs
when there are potentially hazardous
boating conditions.
G Gasoline is highly flammable, and its
vapors are flammable and explosive.
Handle and store gasoline carefully. Make
sure there are no gas fumes or leaking
fuel before starting the engine.
G Check throttle, shift, and steering for
proper operation before starting the
engine.
G Attach the engine stop switch lanyard to a
secure place on your clothing, or your
arm or leg while operating. If you acciden-
tally leave the helm, the lanyard will pull
from the switch, stopping the engine.
G Know the marine laws and regulations
where you will be boating - and obey
them. Refer to the “RULES OF THE
ROAD” section for basic boating rules.
G Stay informed about the weather. Check
weather forecasts before boating. Avoid
boating in hazardous weather.
G Tell someone where you are going: leave
a Float Plan with a responsible person.
Be sure to cancel the Float Plan when
you return.
G Use common sense and good judgment
when boating. Know your abilities, and be
sure you understand how your boat han-
dles under the different boating conditions
you may encounter. Operate within your
limits, and the limits of your boat. Always
operate at safe speeds, and keep a care-
ful watch for obstacles and other traffic.
G Always watch carefully for swimmers dur-
ing the engine operation.
G Stay away from swimming areas.
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
E
G When a swimmer is in the water near you
shift into neutral and shut off the engine.
G Be informed about boating safety. Addi-
tional publications and information can be
obtained from many organizations, includ-
ing the following:
United States Coast Guard
Consumer Affairs Staff (G-BC)
Office of Boating, Public, and Consumer
Affairs
U.S. Coast Guard Headquarters
Washington, D.C. 20593-0001
Boating Safety Hotline: 1-800-368-5647
National Marine Manufacturers Associa-
tion (NMMA)
401 N. Michigan Ave.
Chicago, Il 60611
Marine Retailers Association of America
155 N. Michigan Ave.
Chicago, Il 60601
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00015
Stand-on vessel
BASIC BOATING RULES
The vessel with the right-of-way has the duty
to continue its course and speed, except to
avoid an immediate collision. When you
maintain your direction and speed, the other
vessel will be able to determine how best to
avoid you.
(Rules of the road)
Just as there are rules which apply when
you are driving on streets and high ways,
there are waterway rules which apply when
you are driving your boat. These rules are
used internationally, and are also enforced
by the United States Coast Guard and local
agencies. You should be aware of these
rules, and follow them whenever you
encounter another vessel on the water.
Give-way vessel
The vessel which does not have the right-of-
way has the duty to take positive and timely
action to stay out of the way of the Stand-On
vessel. Normally, you should not cross in
front of the vessel with the right-of-way. You
should slow down or change directions
briefly and pass behind the other vessel.
You should always move in such a way that
the operator of the other vessel can see
what you are doing.
Several sets of rules prevail according to
geographic location, but are all basically the
same as the International Rules of the
Road. The rules presented here in your
Owner’s Manual are condensed, and have
been provided for your convenience only.
Consult your local U.S. Coast Guard Auxil-
iary or Department of Motor Vehicles for a
complete set of rules governing the waters
in which you will be using your boat.
“The general prudential rule”
This rule is called Rule 2 in the International
Rules and says,
‘In obeying and construing these rules
due regard shall be had to all dangers of
navigation and collision, and to any spe-
cial circumstances, which may render a
departure from the above rules neces-
sary in order to avoid immediate dan-
ger.’
STEERING AND SAILING RULES
AND SOUND SIGNALS
Whenever two vessels on the water meet
one another, one vessel has the right-of-
way; it is called the “stand-on” vessel. The
vessel which does not have the right-of-way
is called the “give-way” or “burdened” ves-
sel. These rules determine which vessel has
the right-of-way, and what each vessel
should do.
In other words, follow the standard rules
except when a collision will occur unless
both vessels try to avoid each other. If that is
the case, both vessels become “Give-Way”
vessels.
1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
E
avoid an accident. You should keep the
other vessel on your port (left) side. This
rule doesn’t apply if both of you will clear
one another if you continue on your set
course and speed.
RULES WHEN ENCOUNTERING
VESSELS
There are three main situations which you
may encounter with other vessels which
could lead to a collision unless the Steering
Rules are followed:
Meeting
(you are approaching another vessel
head-on)
Crossing
(you are traveling across the other ves-
sel’s path)
Overtaking
(you are passing or being passed by
another vessel)
Crossing
When two power driven vessels are crossing
each other’s path close enough to run the
risk of collision, the vessel which has the
other on the starboard (right) side must keep
out of the way of the other. If the other ves-
sel is on your right, you must keep out of its
way; you are the Give-Way vessel. If the
other vessel is on your port (left) side,
remember that you should maintain course
and direction, provided the other vessel
gives you the right-of-way as it should.
In the following illustration, your boat is in
the center. You should give the right-of-way
to any vessels shown in white area (you are
the Give-Way vessel). Any vessels in the
shaded area must yield to you (they are the
Give-Way vessels). Both you and the meet-
ing vessel must alter course to avoid each
other.
Meeting
If you are meeting another power vessel
head on, and are close enough to run the
risk of collision, neither of you has the right-
of-way! Both of you should alter course to
Overtaking
If you are passing another vessel, you are
the “Give-Way” vessel. This means that the
1-8
Download from Www.Somanuals.com. All Manuals Search And Download.
E
other vessel is expected to maintain its 1. When the sailing vessel is overtaking
course and speed. You must stay out of its
way until you are clear of it. Likewise, if
the power-driven vessel, the power-
driven vessel has the right-of-way.
another vessel is passing you, you should 2. Sailing vessels should keep clear of any
maintain your speed and direction so that
the other vessel can steer itself around you.
fishing vessel.
3. In a narrow channel, a sailing vessel
should not hamper the safe passage of
a power-driven vessel which can navi-
gate only in such a channel.
OTHER SPECIAL SITUATIONS
There are three other rules you should be
aware of when driving your boat around
other vessels.
Reading buoys and other markers
The waters of the United states are marked
for safe navigation by the lateral system of
buoyage. Simply put, buoys and markers
have an arrangement of shapes, colors,
numbers and lights to show which side of
the buoy a boater should pass on when nav-
igating in a particular direction. The mark-
ings on these buoys are oriented from the
perspective of being entered from seaward
(the boater is going towards the port). This
means that red buoys are passed on the
starboard (right) side when proceeding from
open water into port, and black buoys are to
port (left) side. When navigating out of port,
your position with respect to the buoys
should be reversed; red buoys should be to
port and black buoys to starboard.
Narrow channels and bends
When navigating in narrow channels, you
should keep to the right when it is safe and
practical to do so. If the operator of a power-
driven vessel is preparing to go around a
bend that may obstruct the view of other
water vessels, the operator should sound a
prolonged blast on the whistle (4 to 6 sec-
onds). If another vessel is around the bend,
it too should sound the whistle. Even if no
reply is heard, however, the vessel should
still proceed around the bend with caution. If
you navigate such waters with your boat,
you will need to carry a portable air horn,
available from local marine supply stores.
Many bodies of water used by boaters are
entirely within the boundaries of a particular
state. The Uniform State Waterway Marking
System has been devised for these waters.
This system uses buoys and signs with dis-
tinctive shapes and colors to show regula-
tory or advisory information. These markers
are white with black letters and orange
boarders. They signify speed zones,
restricted areas, danger areas, and general
information.
Fishing vessel right-of-way
All vessels which are fishing with nets, lines
or trawls are considered to be “fishing ves-
sels” under the International Rules. Vessels
with trolling lines are not considered fishing
vessels. Fishing vessels have the right-of-
way regardless of position. Fishing vessels
cannot, however, impede the passage of
other vessels in narrow channels.
Sailing vessel right-of-way
Sailing vessels should normally be given the
right-of-way. The exceptions to this are:
1-9
Download from Www.Somanuals.com. All Manuals Search And Download.
E
Remember, markings may vary by geo-
graphic location. Always consult local boat-
ing authorities before driving your boat in
unfamiliar waters.
1-10
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00016¯
FUELING INSTRUCTIONS
WARNING
@
GASOLINE AND ITS VAPORS ARE
HIGHLY FLAMMABLE AND EXPLOSIVE!
G Do not smoke when refueling, and
keep away from sparks, flames, or
other sources of ignition.
G Stop engine before refueling.
G Refuel in a well-ventilated area.
G Take care not to spill gasoline. If gaso-
line spills, wipe it up immediately with
dry rags.
G Do not overfill the fuel tank.
G Tighten the filler cap securely after
refueling.
G If you should swallow some gasoline
inhale a lot of gasoline vapor, or get
gasoline in your eyes, get immediate
medical attention.
G If any gasoline spills onto your skin,
immediately wash with soap and
water. Change clothing if gasoline
spills on it.
G Touch the fuel nozzle to the filler open-
ing or funnel to help prevent electro-
static sparks.
@
CAUTION:
@
Use only new clean gasoline which has
been stored in clean containers and is
not contaminated with water or foreign
matter.
@
1-11
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00019
GASOLINE (PETROL)
Recommended gasoline:
Regular unleaded gasoline with a
minimum octane rating of 86
(Pump Octane Number) = (R+M)/2
If knocking or pinging occurs, use a different
brand of gasoline or premium unleaded fuel.
EMU00027
Gasohol
There are two types of gasohol: gasohol
containing ethanol and that containing meth-
anol. Gasohol containing ethanol can be
used if ethanol content does not exceed
10% and the fuel meets minimum octane
ratings. Gasohol containing methanol is not
recommended by Yamaha because it can
cause fuel system damage or engine perfor-
mance problems.
1-12
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01149
ENGINE OIL
Recommended engine oil;
Use a combination of corresponding SAE
and API shown in the chart below;
Engine oil quantity:
Refer to “SPECIFICATIONS”, Page 4-1.
CAUTION:
@
All four-stroke engines are shipped from
the factory without engine oil.
@
NOTE:
@
If the recommended engine oil is not avail-
able, then a multigrade type engine oil such
as SF-CC/CD,SG-CC/CD or SH-CD can be
used.
@
1-13
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01674
BATTERY REQUIREMENT
CAUTION:
@
Do not use a battery that does not meet
the specified capacity. If a battery which
differs from the specification is used, the
electrical system may perform poorly or
be overloaded, causing electrical sys-
tem damage.
@
Choose a battery which meets the following
specifications.
Minimum cold crank performance
512 Amps at –17.8°C (0°F)
Minimum reserve capacity
182 Minutes at 26.7°C (80°F)
If the outboard motor’s battery voltage
becomes too low, the engine cannot be
started.
1-14
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01395
PROPELLER SELECTION
The performance of your outboard motor will
be critically affected by your choice of pro-
peller, as an incorrect choice could
adversely affect performance and could also
seriously damage the motor. Engine speed
depends on the propeller size and boat load.
If engine speed is too high or too low for
good engine performance, this will have an
adverse effect on the engine.
Yamaha outboard motors are fitted with pro-
pellers chosen to perform well over a range
of applications, but there may be uses
where a propeller with a different pitch would
be more appropriate. For a greater operat-
ing load, a smaller-pitch propeller is more
suitable as it enables the correct engine
speed to be maintained. Conversely, a
larger-pitch propeller is more suitable for a
smaller operating load.
Yamaha dealers stock a range of propellers,
and can advise you and install a propeller on
your outboard that is best suited to your
application.
NOTE:
@
At full throttle and under a maximum boat
load, the engine’s rpm should be within the
upper half of the full throttle operating range,
as listed in “SPECIFICATIONS” on page 4-1.
Select a propeller which fulfills this require-
ment.
If operating under conditions which allow the
engine’s rpm to rise above the maximum rec-
ommended range (such as light boat loads),
reduce the throttle setting to maintain the
rpm in the proper operating range.
@
1-15
Download from Www.Somanuals.com. All Manuals Search And Download.
E
1 Propeller diameter (in inches)
2 Propeller pitch (in inches)
3 Type of propeller (propeller mark)
Refer to the section “CHECKING PROPEL-
LER” for instructions on propeller removal
and installation.
EMU01209¯
START-IN-GEAR PROTECTION
Yamaha outboard motors or Yamaha
approved remote control units are equipped
with start-in-gear protection device(s). This
feature permits the engine to be started only
when it is Neutral. Always select Neutral
before starting the engine.
1-16
Download from Www.Somanuals.com. All Manuals Search And Download.
E
-MEMO-
1-17
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00037
Chapter 2
BASIC COMPONENTS
MAIN COMPONENTS................................2-1
2
OPERATIONS OF CONTROLS AND
OTHER FUNCTIONS..................................2-2
Remote control.........................................2-2
Trim tab ....................................................2-8
Power trim/tilt switch ................................2-9
Digital tachometer..................................2-10
Digital speedometer...............................2-13
Fuel management meter .......................2-16
Tilt support lever.....................................2-19
Top cowling lock levers..........................2-20
Flushing device......................................2-20
WARNING SYSTEM.................................2-21
Overheat warning...................................2-21
Low oil pressure warning.......................2-22
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01206
MAIN COMPONENTS
1 Top cowling
* 0 Remote control box (Side mount type)
2 Anti-cavitation plate
3 Trim tab (Anode)
* 4 Propeller
* A Remote control box (Binnacle mount type)
* B Switch panel (For use with A)
* C Digital speedometer
5 Cooling water inlet
6 Clamp bracket
* D Digital tachometer
* E Fuel management meter
7 Top cowling lock levers
8 Power trim and tilt switch
9 Flushing device
* May not be exactly as shown; also may not be in-
cluded as standard equipment on all models.
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00039
A
B
C
OPERATIONS OF CONTROLS
AND
OTHER FUNCTIONS
EMU01273
REMOTE CONTROL
Both the shifter and the throttle are actuated
by the remote control lever. In addition, the
electrical switches are mounted on the
remote control box.
È Side mount remote control box
É Binnacle mount remote control box
Ê Switch panel (for use with É)
1 Remote control lever
2 Neutral interlock trigger
3 Neutral throttle lever
4 Free accelerator
5 Main switch
6 Engine stop lanyard switch
7 Power trim/tilt switch
8 Throttle friction adjusting screw
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00098
Remote Control Lever
Moving the lever forward from the Neutral
position engages Forward gear. Pulling the
lever back from Neutral engages Reverse.
The engine will continue to run at idle until
the lever is moved about 35° (a detent can
be felt). Moving the lever farther opens the
throttle, and the engine will begin to acceler-
ate.
1 Neutral
2 Forward
3 Reverse
4 Shift
5 Fully closed
6 Throttle
7 Fully open
EMU00099
Neutral Interlock Trigger
To shift out of Neutral, the neutral interlock
trigger of the remote control lever must first
be pulled up.
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00100
Neutral Throttle Lever
To open the throttle without shifting into
either Forward or Reverse, place the remote
control lever in the Neutral position and lift
the neutral throttle lever.
NOTE:
@
The neutral throttle lever will operate only
when the remote control lever is in Neutral.
The remote control lever will operate only
when the neutral throttle lever is in the
closed position.
@
1 Fully open
2 Fully closed
EMU00101
Main switch
The main switch controls the ignition sys-
tem; its operation is described below.
G OFF
Electrical circuits switched off.
(The key can be removed.)
G ON
Electrical circuits switched on.
(The key cannot be removed.)
G START
Starter-motor will turn and start engine.
(When the key is released, it returns auto-
matically to “ON”.)
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00934
Engine Stop Lanyard Switch
The lock-plate 1 must be attached to the
engine stop lanyard switch for the engine to
run. The lanyard 2 should be attached to a
secure place on the operator’s clothing, or
arm or leg. Should the operator fall over-
board or leave the helm, the lanyard will pull
out the lock plate, stopping ignition to the
engine. This will prevent the boat from run-
ning away under power.
WARNING
@
G Attach the lanyard to a secure place on
your clothing, your arm or leg while
operating.
G Do not attach the lanyard to clothing
that could tear loose. Do not route the
lanyard in such a way that it could
become entangled, preventing it from
functioning.
G Avoid accidentally pulling the lanyard
during normal operation. Loss of
engine power means the loss of most
steering control. Also, without engine
power, the boat could slow rapidly.
This could cause people and objects
in the boat to be thrown forward.
@
NOTE:
@
The engine cannot be started with the lock-
plate removed.
@
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01112
Power Trim/Tilt Switches
The power trim/tilt adjusts the motor angle in
relation to the transom. The power trim/tilt
switch is located on the remote control lever
grip. Individual-engine switches are also on
the control cover. Pushing the switch “UP”
trims the motor up, then tilts the motor up.
Pressing the switch “DN” tilts the motor
down and trims the motor down. When the
switch button is released, the motor will stop
in its current position.
NOTE:
@
G On the dual engine control, the switch on
the remote control grip controls both
engines at the same time.
G Refer to the sections “Adjusting Trim
Angle” and “Tilting Up/Down” in Chapter 3
for instructions on usage.
@
EMU00106
Free Accelerator
To open the throttle without shifting into
either Forward or Reverse, push the free
accelerator button and turn the remote con-
trol lever.
NOTE:
@
G The free accelerator button can be oper-
ated only when the remote control lever is
in the Neutral position.
G After the button is pushed, the remote
control lever must be moved at least 35°
to begin opening the throttle.
G After operating the free accelerator, return
the remote control lever to the Neutral
position. The free accelerator button will
return automatically to its set position.
The remote control will then engage For-
ward and Reverse normally.
@
@
1 Fully-open
2 Fully-closed
3 Free accelerator
2-6
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01155
Throttle Friction Adjusting Screw
A friction device in the remote control box
provides adjustable resistance to move-
ment of the remote control lever, and can be
set according to operator preference. An
adjusting screw is located on the front of the
remote control box.
Resistance
Increase
Screw
Turn clockwise
Turn counterclockwise
Decrease
WARNING
Do not overtighten the friction adjusting
screw. If there is too much resistance, it
may be difficult to move the lever, which
could result in an accident.
@
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01552
TRIM TAB
The trim tab should be adjusted so that the
steering control can be turned to either the
right or left by applying the same amount of
force.
WARNING
@
An improperly adjusted trim tab may
cause difficult steering. Always test run
after the trim tab has been installed or
replaced to be sure steering is correct.
Be sure you have tightened the bolt after
adjusting the trim tab.
@
1 Trim tab
2 Bolt
3 Cap (if equipped)
Boat tends to veer
The fin of trim tab
To the left
(port side)
Turn to the left
(A in the figure)
To the right
(starboard side)
Turn to the right
(B in the figure)
CAUTION:
@
The trim tab also serves as an anode to
protect the engine from electrochemical
corrosion. Never paint the trim tab as it
will become ineffective as an anode.
@
2-8
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01563
POWER TRIM/TILT SWITCH
The power trim/tilt adjusts the motor angle in
relation to the transom. The power trim/tilt
switch is located on the side of the bottom
engine cowling. Pushing the switch “UP”
trims the motor up, then tilts the motor up.
Pressing the switch “DN” tilts the motor
down and trims the motor down. When the
switch button is released, the motor will stop
in its current position.
WARNING
@
@
Use the power trim/tilt switch located on
the bottom engine cowling only when the
boat is at a complete stop with the
engine off. Attempting to use the cowl-
ing-mounted power trim/tilt switch while
the boat is moving could increase the
risk of falling overboard and could dis-
tract the operator, increasing the risk of
collision with another boat or an obsta-
cle.
@
NOTE:
@
Refer to the sections “ADJUSTING TRIM
ANGLE” and “TILTING UP/DOWN” for
instructions on usage.
@
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01617
DIGITAL TACHOMETER
This gauge contains the tachometer, trim
meter, hour meter, low oil pressure warning
indicator, and the overheat warning indica-
tor.
1 Tachometer
2 Trim meter
3 Hour meter
4 Low oil pressure warning indicator
5 Overheat warning indicator
6 Set button
7 Mode button
NOTE:
@
All segments of the display will light momen-
tarily after the main switch is turned on and
will return to normal thereafter.
@
EMU00136
Tachometer
This meter shows the engine speed.
2-10
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01109
Trim Meter
This meter shows the trim angle of your out-
board motor.
NOTE:
@
G Memorize the trim angles that work best
for your boat under different conditions.
Adjust the trim angle to the desired set-
ting by operating the power trim and tilt
switch.
G If the trim angle of your motor exceeds
the trim operating range, the top segment
on the trim meter display will start to blink.
@
EMU01620
Hour Meter
This meter shows the number of hours the
engine has been run. It can be set to show
the total number of hours or the number of
hours for the current trip. The display can
also be turned on and off.
G Changing the display format
Pressing the MODE button changes the
display format in the following circular pat-
tern:
Total hours - Trip hours - Display off
G Resetting the trip hours
Simultaneously pressing the SET and
MODE buttons for more than 1 second
while the trip hours are displayed resets
the trip counter to 0 (zero).
NOTE:
@
The total number of hours the engine has
been run cannot be reset.
@
2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01110
Low Oil Pressure Warning Indicator
If oil pressure drops too low, the warning
indicator will start to blink. Refer to the sec-
tion “LOW OIL PRESSURE WARNING” for
details.
1 Low oil pressure warning indicator
CAUTION:
@
G Do not operate the engine without oil.
Serious engine damage will occur.
G The low oil pressure warning indicator
does not indicate the oil level in the
engine. Use the Oil Level Gauge to
check the remaining oil quantity.
(Refer to the section “CHECKING THE
ENGINE OIL LEVEL” for details.)
@
EMU01553
Overheat Warning Indicator
If the engine temperature rises too high, the
warning indicator will start to blink. Refer to
“OVERHEAT WARNING” for details.
1 Overheat warning indicator
CAUTION:
@
Do not continue to operate the engine if a
warning device has activated. If neces-
sary, refer to the “TROUBLESHOOTING”
section in this manual. Consult your
dealer if the problem cannot be located
and corrected.
@
2-12
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00140
DIGITAL SPEEDOMETER
This meter contains the speedometer, fuel
meter with warning, trip meter, clock and
voltmeter with warning.
1 Speedometer
2 Fuel meter
3 Trip meter/clock/voltmeter
4 Warning indicator
NOTE:
@
After the main switch is first turned on, all
portions of the meter come on as a check.
After a few seconds, the meters will change
to normal operation. Watch the meter when
turning on the main switch to make sure all
segments come on.
@
EMU00141
Speedometer
This meter shows the boat speed.
NOTE:
@
The speedometer displays km/h, mph, or
knots, depending upon operator preference.
Select the desired unit of measurement by
setting the selector switch on the back of the
meter. See the illustration for settings.
@
1 Cap
2 Selector switch (for speed unit)
3 Selector switch (for fuel sender)
2-13
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01274
Trip Meter
This meter displays the distance the boat
has traveled since the meter was last reset.
Repeatedly push and release the “mode”
button until the indicator on the face of the
meter points to “TRIP”. To reset the trip
meter to “0”, press the “set” and “mode” but-
ton together.
NOTE:
@
G The trip distance is shown in kilometers or
miles depending upon the unit of mea-
surement selected for the speedometer.
G The trip distance is kept in memory by
battery power. The stored data will be lost
if the battery is disconnected.
@
EMU01275
Clock
This meter shows the current time.
Repeatedly push and release the “mode”
button until the indicator on the face of the
meter points to “TIME.” To set the clock, be
sure the meter is in the “TIME” mode. Press
the “set” button; the hour display will begin
blinking. Press the “mode” button until the
desired hour is displayed. Press the “set”
button again, the minute display will begin
blinking. Press the “mode” button until the
desired minute is displayed. Press the “set”
button again to start the clock.
NOTE:
@
The clock operates on battery power. Dis-
connecting the battery will stop the clock.
Reset the clock after connecting the battery.
@
2-14
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01554
Fuel meter
The fuel level is indicated by eight seg-
ments. When all segments are showing, the
fuel tank is full.
CAUTION:
@
The Yamaha fuel tank sensor differs from
conventional sensors. Incorrectly set-
ting the selector switch on the meter will
give false readings. Consult your
Yamaha dealer on how to correctly set
the selector switch.
@
NOTE:
@
The fuel reading can be affected by the posi-
tion of the sensor in the fuel tank and the
attitude of the boat in the water. Operation
with bow-up trim or continuous turning can
give false readings.
@
EMU01555
Warning indicators
G Fuel warning
If the fuel level decreases to one segment
the fuel level warning segment 1 will begin
blinking.
G Low battery voltage warning
If battery voltage drops, the display 2 will
automatically turn on and begin blinking.
CAUTION:
@
Do not continue to operate the engine if a
warning device has activated. Refer to
the “TROUBLESHOOTING” section in
this manual. Consult your Yamaha dealer
if the problem cannot be located and cor-
rected.
@
2-15
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00146¯
FUEL MANAGEMENT METER
The meter contains the fuel flow meter, fuel
consumption meter, fuel economy meter,
twin engine speed synchronizer, water sep-
arator warning indicator.
1 Fuel flow meter
2 Fuel consumption / Fuel economy meter / Twin
engine speed synchronizer
3 Water separator warning indicator (Operates
only if the sensor has been installed.)
NOTE:
@
After the main switch is first turned on, all
portions of the meter come on as a check.
After a few seconds, the meters will change
to normal operation. Watch the meter when
turning on the main switch to make sure all
segments come on.
@
2-16
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00147
Fuel Flow Meter
The meter displays fuel flow within one hour,
at the rate of current engine operation.
If twin engines are installed on your boat,
the meter will display total fuel flow of Port
and Starboard side engine. It also displays
PS indication at the same time.
By pressing “set” button, the meter will dis-
play fuel flow of starboard side engine and S
indication.
By pressing “set” button again, the meter will
display fuel flow of port side engine and P
indication.
By pressing “set” button again, the meter will
display total fuel flow.
NOTE:
@
G The meter displays gallon/hour and liter
depending upon operator preference.
Select the desired unit of measurement
by setting the selector switch 1 on the
back of the meter during installation.
G Fuel consumption meter and Fuel econ-
omy meter will indicate same unit of mea-
surement.
@
EMU01276
Fuel Consumption Meter
This meter displays the total amount of fuel
consumed since the meter was last reset.
Repeatedly push and release the “mode”
button until the indicator on the face of the
meter points to total (“TTL”). To reset the
total fuel consumption to “0”, press the “set”
and “mode” buttons together.
2-17
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01277
Fuel Economy
This meter displays the distance per liter or
gallon when cruising for reference use by
the operator.
Repeatedly push and release the “mode”
button until the indicator on the face of the
meter points to “ECON.”
NOTE:
@
If twin engines are installed on your boat,
the meter will display only the total fuel
economy of both engines.
@
NOTE:
@
G Fuel consumption varies greatly with boat
design, weight, propeller used, engine
trim angle, sea conditions (including
wind), and throttle position. Fuel con-
sumption also varies slightly with the type
of water (salt, fresh, and contaminate lev-
els), air temperature and humidity, cleanli-
ness of the boat bottom, engine mounting
height, skill of the operator, and individual
gasoline formulation (winter or summer
fuel and amount of additives).
G The Yamaha digital speedometer and fuel
management meter calculates speed,
miles traveled, and fuel economy by water
movement at the stern of the boat. This
distance can vary greatly from the actual
distance traveled because of water cur-
rents, sea swells, and the condition of the
water speed sensor (partially plugged or
damaged).
G Individual engines may slightly vary in
their fuel consumption due to manufactur-
ing variations. These variations can be
even greater if the engines are of different
year models. In addition, variations in pro-
pellers, even of the same basic dimen-
sions of the same design, can also cause
a slight variation in fuel consumption.
@
2-18
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01278
Twin Engine Speed Synchronizer
This meter displays the difference in engine
speed (r/min) between the Port and Star-
board engines for reference purposes when
synchronizing the two engines’ speeds.
Repeatedly push and release the “mode”
button until the indicator on the face of the
meter points to “SYNC”.
1 Port side engine speed is higher
2 Port side engine speed is slightly higher
3 Engine speed is synchronized evenly between
Port and Starboard side engines
4 Starboard side engine speed is slightly higher
5 Starboard side engine speed is higher
NOTE:
@
If the two engines’ speeds are not synchro-
nized while cruising, they can be synchro-
nized by adjusting trim angle or throttle.
@
EMU01207
Water Separator Warning Indicator
If the water which has been separated from
fuel in the water trap exceeds a specific vol-
ume, the indicator will blink showing the
need for water to be drained.
NOTE:
@
.
This indicator only operates when a water
separator sensor is equipped.
@
EMU00157
TILT SUPPORT LEVER
To keep the outboard motor in the tilted-up
position, lock the tilt support lever to the
clamp bracket.
2-19
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01625¯
TOP COWLING LOCK LEVERS
To remove the engine top cowling, pull up
the front and side lock levers. Then lift off the
cowling. When replacing the cowling, check
to be sure it fits properly in the rubber seal.
Then lock the cowling again by moving the
levers downward.
EMU01546
FLUSHING DEVICE
This device 1 is used to clean the cooling
water passages of the motor using a garden
hose and tap water.
NOTE:
@
Refer to “CLEANING COOLING-WATER
PASSAGES” in Chapter 4 for instructions on
usage.
@
2-20
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00169
WARNING SYSTEM
CAUTION:
@
Do not continue to operate the engine if
the warning device has activated. Con-
sult your Yamaha dealer if the problem
cannot be located and corrected.
@
EMU01664
OVERHEAT WARNING
This engine has an overheat warning
device. If the engine temperature rises too
high, the warning device will activate.
Activation of the warning device
G The engine speed will automatically
decrease to about 2,000 r/min.
G The overheat warning indicator will come
on.
G The buzzer will sound.
If the warning system has been activated,
stop the engine and check the water inlet for
clogging.
NOTE:
@
In case of dual engine drive;
Should the overheat warning system of one
engine operate, it slows down and the
buzzer sounds. This will cause the other
engine to slow down and the buzzer to
sound. For the other engine, the warning
system can be released by shifting the
remote control lever into the neutral.
@
2-21
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01665
LOW OIL PRESSURE WARNING
If oil pressure drops too low, the warning
device will activate.
Activation of the warning device
G The engine speed will automatically
decrease to about 2,000 r/min.
G The low oil pressure warning indicator will
come on.
G The buzzer will sound.
If the warning system has been activated,
stop the engine as soon as it is safe to do
so. Check oil level and add oil as needed. If
the oil level is correct, consult your Yamaha
dealer.
CAUTION:
@
Do not continue to run the engine if the
low oil pressure lamp is “ON”. Serious
engine damage may occur.
@
2-22
Download from Www.Somanuals.com. All Manuals Search And Download.
E
-MEMO-
2-23
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00174
Chapter 3
OPERATION
INSTALLATION..........................................3-1
BREAKING IN (RUNNING IN) ENGINE....3-2
PRE-OPERATION CHECKS .....................3-3
Checking the engine oil level...................3-4
Filling fuel .................................................3-4
STARTING ENGINE...................................3-5
Procedure for remote control model........3-6
3
WARMING UP ENGINE.............................3-8
CHECKING POINTS AFTER
STARTING ENGINE...................................3-8
SHIFTING....................................................3-9
Forward ....................................................3-9
Reverse....................................................3-9
STOPPING ENGINE.................................3-10
TRIMMING OUTBOARD MOTOR...........3-11
Adjusting trim angle................................3-12
TILTING UP/DOWN..................................3-14
Procedure for tilting up...........................3-15
Procedure for tilting down......................3-16
CRUISING IN OTHER CONDITIONS......3-17
Cruising in salt water..............................3-17
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00175
INSTALLATION
CAUTION:
@
Incorrect engine height or obstructions
to smooth water flow (such as the design
or condition of the boat or accessories
such as transom ladders/depth finder
transducers) can create airborne water
spray while the boat is cruising. Severe
engine damage may result if the motor is
operated continuously in the presence of
airborne water spray.
@
NOTE:
@
During water testing check the buoyancy of
the boat, at rest, with its maximum load.
Check that the static water level on the
exhaust housing is low enough to prevent
water entry into the powerhead, when water
rises due to waves when the outboard is not
running.
@
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00224
BREAKING IN (RUNNING IN)
ENGINE
Your new engine requires a period of break-
in (running-in) to allow mating surfaces of
moving parts to wear-in evenly. Correct
break-in (running-in) will help ensure proper
performance and longer engine life.
CAUTION:
@
Failure to follow the break-in (running-in)
procedure may result in reduced engine life
or even severe engine damage.
@
Break-in (running-in) time: 10 hours
EMU01367¯
Run the engine under load (in gear with a
propeller installed) as follows.
1) For the first hour of operation:
Run the engine at 2,000 r/min or at
approximately half throttle.
2) For the second hour of operation:
Run the engine at 3,000 r/min or at
approximately three-quarter throttle.
3) For the next eight hours of operation:
Avoid continuous operation at full throt-
tle for more than five minutes at a time.
4) After the first 10 hours:
Operate the engine normally.
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00204
PRE-OPERATION CHECKS
WARNING
@
If any item in the pre-operation check is
not working properly, have it inspected
and repaired before operating the out-
board motor. Otherwise, an accident
could occur.
@
CAUTION:
@
Do not start the engine out of water.
Overheating and serious engine damage
can occur.
@
EMU01655
Fuel
G Check to be sure you have plenty of fuel
for your trip.
G Make sure there are no fuel leaks or gas-
oline fumes.
G Check fuel line connections to be sure
they are tight.
G Be sure that the fuel hose is not twisted or
flattened, or likely to contact sharp
objects.
EMU00208
Oil
G Check the level of the oil in the sump with
the dipstick. If necessary, add oil to bring
the level up to the upper mark.
EMU00209
Controls
G Check throttle, shift, and steering for
proper operation before starting the
engine.
G The controls should work smoothly, with-
out binding or unusual free play.
G Look for loose or damaged connections.
G Check operation of the starter and stop
switches when the outboard motor is in
the water.
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00211
Engine
G Check the engine and engine mounting.
G Look for loose or damaged fasteners.
G Check the propeller for damage.
G Check that the battery is in good condition
and battery connections are secure.
EMU01436
CHECKING THE ENGINE OIL LEVEL
1) Put the outboard motor in an upright
position (not tilted).
2) Pull out the oil dipstick and wipe it clean.
3) Completely re-insert the dipstick and
pull out it again.
4) Check the oil level using the dipstick to
be sure the level falls between the upper
and lower marks. Fill with oil if it is below
the lower mark, or drain to the specified
level if it is above the upper mark.
1 Oil dipstick
2 Lower level mark
3 Upper level mark
EMU01031
FILLING FUEL
1) Remove the fuel tank cap.
2) Fill the fuel tank carefully.
3) Close the cap securely after refueling.
Wipe up any spilled fuel.
3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01197
STARTING ENGINE
WARNING
@
G Before starting the engine, make sure
that the boat is tightly moored and that
you can steer clear of any obstruc-
tions. Be sure there are no swimmers
in the water near you.
G When the air vent screw is loosened,
gasoline (petrol) vapor will be
released. Gasoline (petrol) is highly
flammable, and its vapors are flamma-
ble and explosive. Refrain from smok-
ing, and keep away from open flames
and sparks while loosening the air
vent screw.
G This product emits exhaust gases
which contain carbon monoxide, a col-
orless, odorless gas which may cause
brain damage or death when inhaled.
Symptoms include nausea, dizziness,
and drowsiness. Keep cockpit and
cabin areas well ventilated. Avoid
blocking exhaust outlets.
@
1) If there is an air vent screw on the fuel
tank cap, loosen it 2 or 3 turns.
2) If there is a fuel joint or a fuel cock on
the boat, firmly connect the fuel line to
the joint or open the fuel cock.
3) Squeeze the primer bulb with the outlet
end up until you feel it become firm.
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00248
PROCEDURE FOR REMOTE
CONTROL MODEL
4) Place the remote control lever in the
Neutral position.
NOTE:
@
The start-in-gear protection device permits
the engine to be started only when it is in
Neutral.
@
5) Attach the engine stop switch lanyard to
a secure place on your clothing, or your
arm or leg. Then, install the lock plate
on the other end of the lanyard in the
engine stop switch.
WARNING
@
G Attach the engine stop switch lanyard
to a secure place on your clothing,
your arm or leg while operating.
G Do not attach the lanyard to clothing
that could tear loose. Do not route the
lanyard where it could become entan-
gled, preventing it from functioning.
G Avoid accidentally pulling the lanyard
during normal operation. Loss of
engine power means the loss of most
steering control. Also, without engine
power, the boat could slow rapidly.
This could cause people and objects
in the boat to be thrown forward.
@
3-6
Download from Www.Somanuals.com. All Manuals Search And Download.
E
6) Turn the main switch to “ON”.
NOTE:
@
In case of dual-engine operation, when the
main switch is turned on, the buzzer oper-
ates for a few seconds and stops automati-
cally. Should either of the dual engines stall,
the buzzer operates.
@
EMU00949
Electric Start Model
7) Turn the main switch to “START”, and
hold it for a maximum of 5 seconds.
8) Immediately after the engine starts,
release the main switch to return it to
“ON”.
CAUTION:
@
G Do not turn the main switch to
“START” when the engine is running.
G Do not keep the starter-motor turning
for more than 5 seconds. The battery
will rapidly become exhausted and it
will be impossible for it to start the
engine. If the engine does not start
within 5 seconds, return the main
switch to “ON”, wait 10 seconds, and
then crank the engine again.
@
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01198¯
WARMING UP ENGINE
1) Before beginning operation, allow the
engine to warm up at idling speed for 3
minutes. (Failure to do this will shorten
engine life.)
EMU01656
CHECKING POINTS AFTER
STARTING ENGINE
G After the engine has warmed up, check
that the engine idling speed is stable.
G Check that the low oil pressure warning
indicator light is off. (Refer to “WARNING
SYSTEM” section.)
G Check for a steady flow of water from the
cooling-water pilot hole.
CAUTION:
@
G If water is not flowing out of the pilot
hole at all times while the engine is
running, do not continue to run the
engine. Overheating and serious dam-
age could occur. Stop the engine and
check if the water inlet on the lower
casing is blocked. If the problem can-
not be found and corrected, consult
your Yamaha dealer.
G If the cooling passage is frozen, it may
take awhile for water to start flowing
out of the pilot hole.
@
3-8
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00261
SHIFTING
WARNING
@
Before shifting, make sure there are no
swimmers or obstacles in the water near
you.
@
CAUTION:
@
To change the shifting position from for-
ward to reverse or vice-versa, close the
throttle first so that the engine idles (or
runs at low speeds).
@
EMU00264
FORWARD
Pull up the neutral interlock trigger (if
equipped) and move the remote control
lever quickly and firmly from Neutral to For-
ward.
EMU00269
REVERSE
WARNING
@
When operating in Reverse, go slowly.
Do not open the throttle more than half.
Otherwise, the boat may become unsta-
ble, which could result in loss of control
and an accident.
@
Pull up the neutral interlock trigger (if
equipped) and move the remote control
lever quickly and firmly from Neutral to
Reverse.
3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00273
STOPPING ENGINE
Let it cool off for a few minutes at idle or low
speed first. Stopping the engine immediately
after operating at high speed is not recom-
mended.
EMU01199¯
1) Turn the main switch to “OFF”.
2) If there is a fuel joint or a fuel cock on
the boat, disconnect the fuel line or
close the fuel cock after stopping the
engine.
3) Tighten the air vent screw on the fuel
tank cap after stopping the engine, if it is
equipped.
4) Remove the key if the boat will be left
unattended.
NOTE:
@
The engine can also be stopped by pulling
the lanyard and removing the lock plate from
the engine stop lanyard switch (then turning
the main switch to “OFF”).
@
3-10
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01412
TRIMMING OUTBOARD
MOTOR
The trim angle of the outboard motor helps
determine the position of the bow of the boat
in the water. The correct trim angle will help
improve performance and fuel economy
while reducing strain on the engine. The cor-
rect trim angle depends upon the combina-
tion of boat, engine, and propeller. Correct
trim is also affected by variables such as the
load in the boat, sea conditions, and running
speed.
WARNING
@
Excessive trim for the operating condi-
tions (either trim up or trim down) can
cause boat instability and can make
steering the boat more difficult. This
increases the possibility of an accident.
If the boat begins to feel unstable or is
hard to steer, slow down and/or readjust
the trim angle.
@
NOTE:
@
Refer to the section “ADJUSTING TRIM
ANGLE” for instructions on usage.
@
1 Trim operating angle
3-11
Download from Www.Somanuals.com. All Manuals Search And Download.
E
ADJUSTING TRIM ANGLE
EMU01657
Power Trim/Tilt Model
WARNING
@
G Be sure all people are clear of the out-
board motor when adjusting the trim/
tilt angle, also be careful not to pinch
any body parts between the drive unit
and clamp bracket.
G Use caution when trying a trim posi-
tion for the first time. Increase speed
gradually and watch for any signs of
instability or control problems.
G Use the power trim/tilt switch located
on the bottom engine cowling (if
equipped) only when the boat is at a
complete stop with the engine off.
@
The outboard motor trim angle can be
adjusted operating the power trim/tilt switch
1.
To raise the bow (“trim-out”), push the switch
UP.
To lower the bow (“trim-in”), push the switch
DN.
Make test runs with the trim set to different
angles to find the position that works best for
your boat and operating conditions.
NOTE:
@
To adjust the trim angle while the boat is
moving, use the power trim and tilt switch
located on the remote control box.
@
3-12
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01558
Bow Up
When the boat is on plane, a bow-up atti-
tude results in less drag, greater stability
and efficiency. This is generally when the
keel line of the boat is up about 3 to 5
degrees. When trimmed out, the boat may
have more tendency to steer to one side or
the other. Compensate for this as you steer.
The trim tab can also be adjusted to help off-
set this effect.
Too much trim-out puts the bow of the boat
too high in the water. Performance and
economy are decreased because the hull of
the boat is pushing the water and there is
more air drag.
Excessive trim-up can cause the propeller to
ventilate, which reduces performance fur-
ther. When trimmed-out too much, a boat
may “porpoise” (hop in the water), which
could throw the operator and passengers
overboard.
EMU01559
Bow Down
When the bow of the boat is down, it is eas-
ier to accelerate from a standing start onto
plane.
Too much trim-in causes the boat to “plow”
through the water, decreasing fuel economy
and making it hard to increase speed.
Operating with excessive trim-in at higher
speeds also makes the boat unstable.
Resistance at the bow is greatly increased,
heightening the danger of “bow steering”
and making operation difficult and danger-
ous.
1 Bow up
2 Bow down
3 Optimum angle
3-13
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01670
TILTING UP/DOWN
If the engine will be stopped for some time,
or if the boat is moored in shallows, the
engine should be tilted up to protect the pro-
peller and casing from damage by collision
with obstructions, and also to reduce salt
corrosion.
WARNING
@
G Be sure all people are clear of the out-
board motor when adjusting the tilt
angle, also be careful not to pinch any
body parts between the drive unit and
engine bracket.
G Leaking fuel is a fire hazard. Discon-
nect the fuel line or close the fuel cock
if the engine will be tilted for more than
a few minutes. Otherwise, fuel may
leak. (If the fuel connector is provided
on the motor.)
@
CAUTION:
@
G Before tilting the motor, follow the pro-
cedures under “STOPPING ENGINE”.
Never tilt the motor while the engine is
running. Severe damage from over-
heating can result.
G To prevent the cooling water passages
from becoming frozen when the ambi-
ent temperature is 5°C or below, tilt up
the motor after it has been stopped 30
seconds or more.
@
3-14
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01575
PROCEDURE FOR TILTING UP
Power trim and tilt models
1) Disconnect the fuel line or close the fuel
cock.
2) Push the power trim and tilt switch “UP”
until the outboard has tilted up com-
pletely.
3) Turn the tilt support lever toward you to
support the engine.
WARNING
@
G After tilting the engine, be sure to sup-
port it with the tilt support lever. Other-
wise, the engine could fall back down
suddenly if oil in the power trim and tilt
unit should lose pressure.
G Never operate the engine while it is
supported by the tilt support lever.
@
3-15
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01576¯
4) Once the engine is supported with the
tilt support lever, push the power trim
and tilt switch “DN” (down) to retract the
trim rods.
CAUTION:
@
Be sure to retract the trim rods com-
pletely during mooring. This protects the
rods from marine growths and corrosion
which could damage the power trim and
tilt mechanism.
@
EMU00303
PROCEDURE FOR TILTING DOWN
Power trim/tilt model
1) Push the power trim/tilt switch “UP” until
the engine is supported by the tilt rod.
2) Release the tilt-support lever.
3) Push the power trim/tilt switch “DN”
(Down) to lower the engine to the
desired position.
3-16
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01030
CRUISING IN OTHER
CONDITIONS
CRUISING IN SALT WATER
After operating in salt water, wash out the
cooling-water passages with fresh water to
prevent them from becoming clogged-up
with salt deposits.
NOTE:
@
Refer to cooling system flushing instructions
in “TRANSPORTING AND STORING OUT-
BOARD MOTOR”.
@
3-17
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00317
Chapter 4
MAINTENANCE
SPECIFICATION DATA .............................4-1
TRANSPORTING AND STORING
OUTBOARD MOTOR.................................4-3
Trailering outboard motor ........................4-3
Storing outboard motor............................4-4
PERIODIC MAINTENANCE.....................4-10
Replacement parts.................................4-10
Maintenance chart .................................4-11
Greasing.................................................4-13
Cleaning and adjusting spark plug........4-14
Checking fuel system.............................4-16
Inspecting fuel filter ................................4-17
Changing engine oil...............................4-19
Replacing fuse .......................................4-22
Checking wiring and connectors ...........4-23
Exhaust leakage.....................................4-23
Water leakage........................................4-23
Engine oil leakage..................................4-23
Checking power trim and tilt system......4-24
Checking propeller.................................4-25
Changing gear oil...................................4-27
Inspecting and replacing anode(s)........4-28
Checking battery
4
(for electric start models) .......................4-29
Checking bolts and nuts ........................4-32
Cleaning cooling-water passages .........4-33
Checking top cowling ............................4-34
Motor exterior.........................................4-34
Coating the boat bottom ........................4-34
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00322¯
SPECIFICATION DATA
Model
Unit
F225TRA
Item
DIMENSIONS
Overall Length
Overall Width
Overall Height
Transom height
Weight
mm (in.)
mm (in.)
mm (in.)
mm (in.)
kg (lb.)
892 (35.12)
634 (24.96)
1,805 (71.06)/1,932 (76.06)
643 (25.31)/770 (30.31)
272 (600)/278 (613)
X/U
X/U
X/U
PERFORMANCE
Full throttle operating range
Maximum output
Idling speed (Neutral)
ENGINE
r/min
kW (HP) @ r/min
r/min
5,000 ~ 6,000
165.5 (225)@5,500
650 ~ 750
Type
4-stroke, DOHC, V6
3,352 (204.54)
94.0 × 80.5 (3.70 × 3.17)
TCI
3
Displacement
Bore × stroke
Ignition system
Spark plug
cm (cu.in.)
mm (in.)
NGK
LFR5A-11
Spark plug gap
Control system
Starting system
mm (in.)
1.0 ~ 1.1 (0.039 ~ 0.043)
Remote control
Electric start
Valve clearance (cold engine) IN
EX
Battery capacity
mm (in.)
mm (in.)
V-AH
0.17 ~ 0.23 (0.007 ~ 0.009)
0.31 ~ 0.37 (0.012 ~ 0.015)
12-100
Minimum cold crank performance
Minimum reserve capacity
Alternator output
Amps at –17.8 °C (0 °F) 512
Minutes at 26.7 °C (80 °F) 182
V-A (W)
12-45
Starting carburation system
Electronic fuel injection
DRIVE UNIT
Gear positions
Gear ratio
Forward-Neutral-Reverse
2.00 (30/15)
Trim/tilt system
Propeller mark
Power trim & tilt
T/M
FUEL AND OIL
Recommended fuel
Regular unleaded gasoline
(Minimum 86)
P.O.N.
Fuel tank capacity
l (US gal, Imp qt)
—
Recommended engine oil
4-stroke motor oil
SE, SF, SG, SH, SJ
10W-30,10W-40
6.0 (6.34, 5.3)
Hypoid gear oil (SAE 90)
1,150 (38.88, 40.56)
API
SAE
l (US qt, Imp qt)
Engine oil capacity
Recommended gear oil
Gear oil capacity
TIGHTENING TORQUE
Spark plug
Propeller nut
Engine oil drain bolt
Engine oil filter
3
cm (US oz, Imp oz)
N·m (kgf·m, lb·ft)
N·m (kgf·m, lb·ft)
N·m (kgf·m, lb·ft)
N·m (kgf·m, lb·ft)
25 (2.5, 18)
54 (5.4, 39)
27 (2.7, 20)
18 (1.8, 13)
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
E
LF225TRA
—
—
892 (35.12)
634 (24.96)
1,805 (71.06)/1,932 (76.06)
643 (25.31)/770 (30.31)
272 (600)/278 (613)
5,000 ~ 6,000
165.5 (225)@5,500
650 ~ 750
4-stroke, DOHC, V6
3,352 (204.54)
94.0 × 80.5 (3.70 × 3.17)
TCI
LFR5A-11
1.0 ~ 1.1 (0.039 ~ 0.043)
Remote control
Electric start
0.17 ~ 0.23 (0.007 ~ 0.009)
0.31 ~ 0.37 (0.012 ~ 0.015)
12-100
512
182
12-45
Electronic fuel injection
Forward-Neutral-Reverse
2.00 (30/15)
Power trim & tilt
TL/ML
Regular unleaded gasoline
(Minimum 86)
—
4-stroke motor oil
SE, SF, SG, SH, SJ
10W-30,10W-40
6.0 (6.34, 5.3)
Hypoid gear oil (SAE 90)
1,000 (33.81, 35.27)
25 (2.5, 18)
54 (5.4, 39)
27 (2.7, 20)
18 (1.8, 13)
4-2
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01369
TRANSPORTING AND
STORING OUTBOARD MOTOR
WARNING
@
Leaking fuel is a fire hazard. When trans-
porting and storing the outboard motor,
close the air vent screw and fuel cock to
prevent fuel from leaking.
@
EMU00326¯
TRAILERING OUTBOARD MOTOR
The motor should be trailered and stored in
the normal running position. If there is insuf-
ficient road clearance in this position, then
trailer the motor in the tilt position using a
motor support device such as a transom
saver bar.
For further details, consult your Yamaha
dealer.
WARNING
@
G Never get under the lower unit while it
is tilted, even if a motor support bar is
used. Severe injury could occur if the
outboard accidentally falls.
G DO NOT fill fuel container to maximum
capacity. Gasoline will expand consid-
erably as it warms up and can build up
pressure in the fuel container. This can
cause fuel leakage and a potential fire
hazard.
@
CAUTION:
@
Do not use the tilt support lever/knob
when trailering the boat. The outboard
motor could shake loose from the tilt
support and fall. If the motor can not be
trailered in the down position, use an
additional support device to secure it in
the up position.
@
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01259¯
STORING OUTBOARD MOTOR
When storing your outboard motor for pro-
longed periods of time (2 months or longer),
several important procedures must be per-
formed to prevent expensive damage.
It is advisable to have your outboard ser-
viced by an authorized Yamaha dealer prior
to storage. However, the following proce-
dures can be performed by the owner with a
minimum of tools.
CAUTION:
@
G To prevent problems which can be
caused by oil entering the cylinder
from the sump, keep the engine in the
vertical position when transporting
and storing it.
G Do not place the engine on its side
before the cooling water has drained
from it completely, or water may enter
the cylinder through the exhaust port
and cause problems.
G Store the engine in a dry, well-venti-
lated place, not in direct sunlight.
G Drain the remaining gasoline from the
vapor separator. Gasoline left in the
vapor separator 1 for a prolonged
period of time will break down and
possibly cause damage to the fuel line.
4-4
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00335
Filling Fuel Tank
Fill the fuel tank with fresh fuel and add one
ounce of “Yamaha Fuel Conditioner and Sta-
bilizer” (Part No. LUB-FUELC-12-00) to
each gallon of fuel.
NOTE:
@
The use of “Yamaha Fuel Conditioner and
Stabilizer” eliminates the need to drain the
fuel system. Consult your Yamaha dealer or
other qualified mechanic if the fuel system is
to be drained instead.
@
EMU00338
Flushing Cooling System and Fogging
Engine
Cooling system flushing is essential to pre-
vent the cooling system from clogging up
with salt, sand, or dirt. In addition, fogging of
the engine is mandatory to prevent expen-
sive engine damage due to rust. Perform the
flushing and fogging at the same time.
WARNING
@
G Do not touch or remove electrical parts
when starting or during operation.
G Keep hands, hair and clothes away
from flywheel and other rotating parts
while engine is running.
@
EMU00342
G Flushing with the Flushing Attachment
CAUTION:
@
Avoid running the outboard at high
speed while on the flushing attachment,
or overheating could occur.
@
1) Remove the top cowling and the propel-
ler.
2) Install a flushing attachment 1 to the
cooling water inlet.
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
E
3) Run the engine at a fast idle for 10~15
minutes supplying fresh water.
4) Just prior to turning off the engine,
quickly spray “Yamaha Stor-Rite Engine
Fogging Oil” (Part No. LUB-STRRT-12-
00) alternately into the silencer cover.
When properly done, the engine will
smoke excessively and almost stall.
5) Remove the flushing attachment and
wipe off any excess water.
6) Install the top cowling and the propeller.
NOTE:
@
A flushing attachment is available from a
Yamaha dealer.
@
EMU00349
Lubrication
1) Remove the spark plug(s). Spray a
Yamaha “Stor-Rite Engine Fogging Oil”
into each cylinder for 10 seconds.
Grease the spark plug threads and rein-
stall the spark plug(s) and torque to
proper specification. (Refer to the
“CLEANING AND ADJUSTING SPARK
PLUG”).
2) Turn the engine over with the stop lan-
yard disconnected to work the fogging
oil into the piston rings.
3) Change the gear-case oil. (Refer to
“CHANGING GEAR OIL”). Inspect the
oil for the presence of water which indi-
cates a leaky seal. Seal replacement
should be performed by an authorized
Yamaha dealership prior to use.
4) Grease all grease fittings. (Refer to the
“GREASING”)
4-6
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00352
Cleaning and Anti-corrosion Measure
1) Wash down the exterior of the outboard
with fresh water and dry off completely.
2) Spray the engine’s exterior with
“Yamaha Silicone Protectant” (Part No.
LUB-SILCNE-13-00).
CAUTION:
@
Do not spray when the engine is running.
Also, do not spray near the silencer and
oxygen sensor cover or into the engine.
Otherwise, the oxygen sensor for Elec-
tronic Fuel Injection system could be
damaged.
@
3) Wax the cowling with a non-abrasive
wax such as “Yamaha Silicone Wax”
(Part No. ACC-11000-15-02).
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01545
Battery Care
WARNING
@
Battery electrolyte is poisonous and dan-
gerous, causing severe burns, etc. It con-
tains sulfuric acid. Avoid contact with
skin, eyes, or clothing.
Antidote:
EXTERNAL: Flush with water.
INTERNAL: Drink large quantities of
water or milk. Follow with milk of magne-
sia, beaten egg, or vegetable oil. Call
physician immediately.
EYES: Flush with water for 15 minutes
and get prompt medical attention.
Batteries produce explosive gases: Keep
sparks, flame, cigarettes, etc. away. Ven-
tilate when charging or using in a closed
space. Always wear eye protection when
working near batteries.
KEEP OUT OF REACH OF CHILDREN.
@
Batteries vary among manufacturers. There-
fore the following procedures may not
always apply. Consult your battery manufac-
turer’s instructions.
1) Disconnect and remove the battery from
the boat. Always disconnect the black
negative lead first to prevent the risk of
shorting.
2) Clean the battery casing and terminals.
Fill each cell to the upper level with dis-
tilled water.
3) Store the battery on a level surface in a
cool, dry, well-ventilated place out of
direct sunlight.
4) Once a month, check the specific gravity
of the electrolyte and recharge as
required to prolong battery life.
4-8
Download from Www.Somanuals.com. All Manuals Search And Download.
E
-MEMO-
4-9
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01569
PERIODIC MAINTENANCE
WARNING
@
Be sure to turn off the engine when you
perform maintenance unless otherwise
specified. If the owner is not familiar with
machine servicing, this work should be
done by a Yamaha dealer or other quali-
fied mechanic.
@
Maintenance, replacement, or repair of
the emission control devices and sys-
tems may be performed by any marine
engine repair establishment or individ-
ual. All warranty repairs, however, includ-
ing those to the emission control system,
must be performed by an authorized
Yamaha marine dealership.
A service manual is available for purchase
through a Yamaha dealer for owners who
have the mechanical skills, tools, and other
equipment necessary to perform mainte-
nance not covered by this owner’s manual.
EMU00356
REPLACEMENT PARTS
If replacement parts are necessary, use only
genuine Yamaha parts or equivalents of the
same type and of equivalent strength and
materials. Any part of inferior quality may
malfunction, and the resulting loss of control
could endanger the operator and passen-
gers.
Yamaha genuine parts and accessories are
available from a Yamaha dealer.
4-10
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01673
MAINTENANCE CHART
Frequency of maintenance operations may be adjusted according to the operating condi-
tions, but the following table gives general guidelines.
The mark (G) indicates the check-ups which you may carry out yourself.
Interval
Initial
Every
Refer
page
10 hours
(after
break-in)
100
hours
200
hours
400
hours
50 hours
(3 months)
Remarks
Inspection
Inspection
Inspection
Cleaning
Inspection
Inspection
Change
Item
(6 months) (1 year) (2 years)
Cowling
Fuel system
G (before each use)
4-34
4-16
G (before each use)
G (before each use)
G
Fuel filter
(Water separator)
4-17
—
G
Fuel tank *1
Engine oil
G
G (before each use)
4-19
G
G
G
Outboard motor exterior
Gear oil
Inspection
Change
G (before each use)
G
4-34
4-27
4-25
Propeller
Inspection
G (before each use)
Cooling water passages
*2
Flushing
G (after each use)
4-5, 4-33
Cleaning/Adjustment/
Replacement
Spark plugs
G
G
4-14
4-13
Greasing points
Greasing
G
*1. If a portable fuel tank is equipped.
*2. When operating in salt water, turbid or muddy water, the engine should be flushed with clean water
after each use.
4-11
Download from Www.Somanuals.com. All Manuals Search And Download.
E
The mark (❍) indicates work to be carried out by your Yamaha dealer.
Interval
Initial
Every
Refer
page
10 hours
(after
break-in)
100
hours
200
hours
400
hours
50 hours
(3 months)
Remarks
Inspection
Change
Item
(6 months) (1 year) (2 years)
Ignition timing
Oil filter
❍
—
—
❍
Fuel filter
(Disposable type)
Inspection/Replacement
❍
❍
—
Oil pump
Inspection
❍
—
—
—
—
—
—
Timing chain
Chain tensioner
Timing belt *3
Valve clearance
Thermostat
Inspection/Replacement
Inspection/Replacement
Inspection/Replacement
Inspection/Adjustment
Inspection
❍ (1,000 hours or 5 years)
❍
❍
❍
❍
PCV
Inspection
❍
—
(Pressure Control Valve)
Oil leakage
Inspection/Replacement
Inspection
❍
❍
❍
❍
4-23
4-32
—
Flywheel nut
Throttle link
Inspection/Adjustment
Inspection/Adjustment
Inspection/Adjustment
Inspection/Adjustment
Inspection/Replacement
Inspection/Replacement
Inspection
❍
Throttle cable
Shift cable
❍
—
❍
—
Idling speed
❍
❍
—
Impeller/Woodruff key
Oil seal
❍ (500 hours or 30 months)
—
❍
❍
❍
❍
❍
❍
—
Power trim and tilt unit
Anodes/Trim tab
Battery
4-24
4-28
4-29
4-23
4-32
Inspection/Replacement
Inspection/Charge
Adjustment/Connection
Retightening
Wiring & connectors
Bolts & nuts *4
❍
❍
*3. Be sure to replace the timing belt after every 1,000 hours (5 years) of operation.
*4. Do not retighten the cylinder head and crankcase bolts.
4-12
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01035
CLEANING AND ADJUSTING SPARK
PLUG
WARNING
@
When removing or installing a spark
plug, be careful not to damage the insu-
lator. A damaged insulator could allow
external sparks, which could lead to
explosion or fire.
@
The spark plug is an important engine com-
ponent and is easy to inspect. The condition
of the spark plug can indicate something
about the condition of the engine. For exam-
ple, if the center electrode porcelain is very
white, this could indicate an intake air leak
or carburetion problem in that cylinder. Do
not attempt to diagnose any problems your-
self. Instead, take the outboard motor to a
Yamaha dealer. You should periodically
remove and inspect the spark plug because
heat and deposits will cause the spark plug
to slowly break down and erode. If electrode
erosion becomes excessive, or if carbon and
other deposits are excessive, you should
replace the spark plug with another of the
correct type.
Standard spark plug:
Refer to “SPECIFICATIONS”, page 4-1.
Before fitting the spark plug, measure the
electrode gap with a wire thickness gauge;
adjust the gap to specification if necessary.
Spark plug gap:
Refer to “SPECIFICATIONS”, page 4-1.
4-14
Download from Www.Somanuals.com. All Manuals Search And Download.
E
When fitting the plug, always clean the gas-
ket surface and use a new gasket. Wipe off
any dirt from the threads and screw in the
spark plug to the correct torque.
Spark plug torque:
Refer to “SPECIFICATIONS”, page 4-1.
NOTE:
@
If a torque-wrench is not available when you
are fitting a spark plug, a good estimate of
the correct torque is 1/4 to 1/2 a turn past
finger-tight. Have the spark plug adjusted to
the correct torque as soon as possible with a
torque-wrench.
@
Initial of spark
Plug wrench size
plug I.D. mark
B
21 mm (13/16 in.)
16 mm (5/8 in.)
C, L
D
18.3 mm (23/32 in.)
1 Spark plug gap
2 Spark plug I.D. mark (NGK)
4-15
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01509
CHECKING FUEL SYSTEM
WARNING
@
Gasoline (petrol) and its vapors are
highly flammable and explosive. Keep
away from sparks, cigarettes, flames or
other sources of ignition.
@
Check the fuel line for leaks, cracks, or mal-
functions. If any problem is found, it should
be repaired immediately by Yamaha dealer
or other qualified mechanic.
Checkpoints
G Fuel system parts leakage.
G Fuel hose joint leakage.
G Fuel hose cracks or other damage.
G Fuel connector leakage.
WARNING
@
Leaking fuel can result in fire or explo-
sion.
G Check for fuel leakage regularly.
G If any fuel leakage is found, the fuel
system must be repaired by a qualified
mechanic. Improper repairs can make
the outboard unsafe to operate.
@
4-16
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00370
INSPECTING FUEL FILTER
WARNING
@
Gasoline (petrol) is highly flammable,
and its vapors are flammable and explo-
sive.
G If you have any question about prop-
erly doing this procedure, consult your
Yamaha dealer.
G Do not perform this procedure on a hot
or running engine. Allow the engine to
cool.
G There will be fuel in the fuel filter. Keep
away from sparks, cigarettes, flames
or other sources of ignition.
G This procedure will allow some fuel to
spill. Catch fuel in a rag. Wipe up any
spilled fuel immediately.
G The fuel filter must be reassembled
carefully with O-ring, filter cup, and
hoses in place. Improper assembly or
replacement can result in a fuel leak,
which could result in a fire or explo-
sion hazard.
@
4-17
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01676
Cleaning Fuel Filter
1) Remove the bolts 1 that are securing
the fuel filter bracket 5 in place.
2) Loosen the bolt 2 that retains the lock
tab 3, and remove the lock tab.
3) Loosen the bolt 4 that secures the fuel
filter in place.
4) Loosen the ring nut 0 of the filter cup
9.
5) Remove the filter cup, catching any
spilled fuel in a container.
6) Remove the filter element 7, and wash
it in solvent. Allow it to dry. Inspect the
filter element and O-ring 8 to make
sure they are in good condition. Replace
them if necessary.
7) Reinstall the filter element in the filter
housing 6.
8) Reinsert the O-ring in its proper posi-
tion, screw the ring nut onto the filler
housing until the filter housing is lightly
seated.
9) Tighten the ring nut approximately an
additional 1/4 turn until the ring nut is
tight. Align the one of the eight large ring
nut tabs into the slot of the locking tab.
Install and tighten the locking tab bolt.
10) Reinstall the fuel filter onto the filter
bracket by tightening the bolt.
11) Reinstall the fuel filter bracket onto the
engine by tightening the bolts.
12) Run the engine and check the filter and
lines for leaks.
NOTE:
@
If any water is in the fuel, the red ring in the
fuel filter unit will float. If so, remove the cup
and drain the water.
@
4-18
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01661
CHANGING ENGINE OIL
WARNING
@
G Avoid extracting or draining the engine
oil immediately after stopping the
engine. The oil is hot and should be
handled with care to avoid burns.
G Be sure the outboard is securely fas-
tened to the transom or a stable stand.
@
CAUTION:
@
Change the engine oil after the first 10
hours of operation, and every 100 hours
or at 6-month intervals thereafter. Other-
wise, the engine will wear quickly.
@
The engine oil can be extracted with an oil
changer (recommended), or drained by
removing the oil drain plug.
Extracting the oil with an oil changer
(normal oil change)
1) Put the outboard motor in an upright
position (not tilted).
2) Pull out the dipstick and use the oil
changer to extract the oil.
4-19
Download from Www.Somanuals.com. All Manuals Search And Download.
E
3) Remove the oil filler cap 1. Add the cor-
rect amount of oil through the filler hole,
and reinstall the filler cap.
Engine oil grade/capacity:
Refer to “SPECIFICATIONS”, page 4-1.
CAUTION:
@
G Do not overfill the oil, and be sure the
engine is in an upright position (not
tilted) when checking and changing
the oil.
G If the oil level is above the upper level
mark, drain until the level meets the
specified capacity. Over filling the oil
may cause leakage or damage.
@
4) Start the engine and watch to make sure
the low oil pressure warning indicator turns
off. Make sure that there are no oil leaks.
CAUTION:
@
If the low oil pressure warning indicator
does not turn off, or if there are oil leaks,
stop the engine and find the cause.
Continued operation with
a
problem
could cause severe engine damage. If
the problem cannot be found and cor-
rected, consult your Yamaha dealer.
@
5) Turn off the engine and wait 3 minutes.
Recheck the oil level using the dipstick
to be sure the level falls between the
upper and lower marks. Fill with oil if it is
below the specified level if it is above the
upper mark.
6) Dispose of used oil according to local
regulations.
NOTE:
@
G For disposal of used oil consult your
Yamaha dealer.
G The oil should be changed more often
when the engine is operated under
adverse conditions such as extended
trolling.
@
4-20
Download from Www.Somanuals.com. All Manuals Search And Download.
E
Draining the oil by removing the oil drain
plug
1) Remove the four bolts to remove the
apron from the starboard side.
2) Tilt the outboard motor 5–10 degrees
up, and then turn it entirely to the star-
board side until the drain plug is directly
below.
3) Prepare a suitable container which can
hold a larger amount than the oil capac-
ity. Loosen and remove the drain bolt 2
while holding the container under the
drain hole. Let the oil drain completely.
Wipe up any spilled oil immediately.
4) Put a new gasket on the oil drain bolt.
Apply a light coat of oil to the gasket and
reinstall the drain bolt.
Tightening torque:
Refer to “SPECIFICATIONS”, page 4-1.
NOTE:
@
G If a torque wrench is not available when
you are installing the drain plug, finger
tighten the bolt just until the gasket comes
into contact with the surface of the drain
hole. Then tighten 1/4-1/2 turn. Have the
drain bolt torqued to the correct value with
a torque wrench as soon as possible.
G Apply grease to the bolts for retaining the
apron before tightening them.
@
4-21
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01662*
REPLACING FUSE
If the fuse has blown on an Electric start
model, open the fuse box and replace the
fuse with a spare one of proper amperage,
using a fuse puller.
WARNING
@
Be sure to use the specified fuse. An
incorrect fuse or a piece of wire may
allow excessive current flow. This could
cause electrical system damage and a
fire hazard.
@
CAUTION:
@
G If a main fuse has blown, be sure to
also check the other main fuse.
G If the outboard motor is operated after
a main fuse has blown charging capa-
bility will be insufficient, and the
engine will not start.
NOTE:
@
If the new fuse blows again immediately,
consult a Yamaha dealer.
@
1 Fuse box
2 Fuse (5 A × 1, 20 A × 2, 30 A × 3)
3 Spare fuse (5 A, 20 A, 30 A)
4 Fuse puller
5 Starter relay
6 Main fuse 2
7 Main fuse 1
8 Fuel feed pump
9 Main switch / Trim switch
0 Engine control unit / Ignition coil / Fuel injec-
tion pump / Fuel injection nozzle / ISC (idle
speed control)
4-22
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00383
CHECKING WIRING AND
CONNECTORS
1) Check that each grounding wire is prop-
erly secured.
2) Check that each connector is engaged
securely.
EMU00384
EXHAUST LEAKAGE
Start the engine and check that no exhaust
leaks from the joints between the exhaust
cover, cylinder head and crank case.
EMU00385
WATER LEAKAGE
Start the engine and check that no water
leaks from the joints between the exhaust
cover, cylinder head and crank case.
EMU01634
ENGINE OIL LEAKAGE
Check that no oil leaks from the engine oil
system.
NOTE:
@
If any leaks are found, consult a Yamaha
dealer.
@
4-23
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00993
CHECKING POWER TRIM AND TILT
SYSTEM
WARNING
@
G Never get under the lower unit while it
is tilted, even when the tilt-support
lever is locked. Severe injury could
occur if the outboard accidentally falls.
G Make sure no one is under the out-
board before performing this test.
@
1) Check the power trim and tilt unit for any
sign of oil leaks.
2) Operate each of the power trim and tilt
switches on remote control and engine
bottom cowling (if equipped) to check
that all switches work.
3) Tilt up the motor and check that the tilt
rod 1 and trim rods 2 are pushed out
completely.
4) Use the tilt support lever 3 to lock the
motor in the UP position. Operate the tilt
down switch briefly so the motor is sup-
ported the tilt support lever.
5) Check that the tilt rod and trim rods are
free of corrosion or other flaws.
6) Activate the tilt-down switch until the
trim rods have gone completely into the
cylinders.
7) Activate the trim-up switch until the tilt
rod is fully extended. Unlock the tilt sup-
port lever.
8) Operate the motor to tilt down. Check
that the tilt rod and trim rods operate
smoothly.
NOTE:
@
If any operation is abnormal, consult a
Yamaha dealer.
@
Recommended fluid:
Yamaha power trim & tilt fluid or ATF
(DEXRON-II).
4-24
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01432¯
CHECKING PROPELLER
WARNING
@
Do not use your hand to hold the propel-
ler when loosening or tightening the pro-
peller nut. Put a wood block between the
cavitation plate and the propeller to pre-
vent the propeller from turning.
@
EMU00390
Propeller Checking Point
G Check each of the propeller blades for
wear, erosion from cavitation or ventila-
tion, or other damage.
G Check the splines for wear and damage.
G Check for fish line winding around the
propeller shaft.
G Check the propeller shaft oil seal for dam-
age.
4-25
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01504
Removing the Propeller
1) Straighten the cotter pin 1 and pull it
out using a pair of pliers.
2) Remove the propeller nut 2, washer 3
and spacer 4.
3) Remove the propeller 5, washer 6 and
spacer 7.
EMU01505
Installing the Propeller
CAUTION:
@
G Be sure to install the spacer and
washer before installing the propeller,
otherwise, the lower case and propel-
ler boss may be damaged.
G Be sure to use a new cotter pin and
bend the ends over securely, other-
wise, the propeller could come off dur-
ing operation and be lost.
@
1) Apply Yamaha Marine grease or Corro-
sion resistant grease to the propeller
shaft.
2) Install the spacer, washer and propeller
on the propeller shaft.
3) Install the spacer, washer and the pro-
peller nut, and then tighten the nut to the
specified torque.
Tightening torque:
Refer to “SPECIFICATIONS” page 4-1.
4) Align the propeller nut with the propeller
shaft hole. Insert a new cotter pin in the
hole and bend the cotter pin ends.
NOTE:
@
If the propeller nut does not align with the
propeller shaft hole after tightening to the
specified torque, then tighten the nut further
to align it with the hole.
@
4-26
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01460
CHANGING GEAR OIL
WARNING
@
G Be sure the outboard is securely fas-
tened to the transom or a stable stand.
You could be severely injured if the
outboard falls on you.
G Never get under the lower unit while it
is tilted, even when the tilt-support
lever/knob is locked. Severe injury
could occur if the outboard acciden-
tally falls.
@
1) Tilt the outboard motor so that the oil
drain plug is at the lowest point possible.
2) Place a suitable container under the
gear-case.
3) Remove the oil drain plug 1.
NOTE:
@
The oil drain plug is magnetic. Remove all
metal particles from the plug before rein-
stalling it.
@
4) Remove the oil level plug 2 to allow the
oil to drain completely.
CAUTION:
@
Inspect the used oil after it has been
drained. If the oil is milky, water is getting
into the gear-case which can cause gear
damage. Consult a Yamaha dealer for
repair of the lower unit seals.
@
NOTE:
@
For disposal of used oil consult your Yamaha
dealer.
@
5) With the outboard motor in a vertical
position, and using a flexible or pressur-
ized filling device, inject the gear oil into
the oil drain plug hole.
Gear oil grade/capacity:
Refer to “SPECIFICATIONS,” page 4-1.
4-27
Download from Www.Somanuals.com. All Manuals Search And Download.
E
6) When the oil begins to flow out of the oil
level plug hole, insert and tighten the oil
level plug.
7) Insert and tighten the oil drain plug.
EMU01037
INSPECTING AND REPLACING
ANODE(S)
Yamaha outboard motor is protected from
corrosion by a sacrificial anode(s).
Check the anode(s) periodically. Remove
the scales from surfaces of the anode(s).
For the inspection and replacement of the
anode(s), consult a Yamaha dealer.
CAUTION:
@
Do not paint the anode(s), for this would
render it ineffective.
@@
NOTE:
@
Remove the cover with anode after remov-
ing the bolts 1 when checking the anode
condition.
@
4-28
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00404
CHECKING BATTERY
(for Electric start models)
WARNING
@
Battery electrolytic fluid is dangerous; it
contains sulfuric acid and therefore is
poisonous and highly caustic.
Always follow these preventive mea-
sures:
G Avoid bodily contact with electrolytic
fluid as it can cause severe burns or
permanent eye injury.
G Wear protective eye gear when han-
dling or working near batteries.
Antidote (EXTERNAL):
G SKIN - Flush with water.
G EYES - Flush with water for 15 minutes
and get immediate medical attention.
Antidote (INTERNAL):
G Drink large quantities of water or milk
followed by milk of magnesia, beaten
egg, or vegetable oil. Get immediate
medical attention.
Batteries also generate explosive hydro-
gen gas; therefore, you should always
follow these preventive measures:
G Charge batteries in a well-ventilated
area.
G Keep batteries away from fire, sparks,
or open flames (e.g., welding equip-
ment, lighted cigarettes, etc.).
G DO NOT SMOKE when charging or
handling batteries.
G KEEP BATTERIES AND ELECTRO-
LYTIC FLUID OUT OF REACH OF CHIL-
DREN.
@
4-29
Download from Www.Somanuals.com. All Manuals Search And Download.
E
CAUTION:
@
G A poorly maintained battery will
quickly deteriorate.
G Ordinary tap-water contains minerals
harmful to a battery, and should not be
used for topping-up.
@
1) Check the electrolyte level at least once
a month. Fill to the manufacturer’s rec-
ommended level when necessary. Top
up only with distilled water (or pure de-
ionized water suitable to use in batter-
ies).
2) Keep the battery always in a good state
of charge. Installing a voltmeter will help
you monitor your battery. If you will not
use the boat for a month or more,
remove the battery from the boat and
store it in a cool, dark place. Completely
recharge the battery before using it.
3) If the battery will be stored for longer
than a month, check the specific gravity
of the fluid at least once a month and
recharge the battery when it is low.
4-30
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01279¯
Connecting the Battery
WARNING
@
Mount the battery holder securely in a
dry, well-ventilated, vibration-free loca-
tion in the boat. Install a fully charged
battery in the holder.
@
CAUTION:
@
G Make sure the main switch (on applica-
ble models) is “OFF” before working
on the battery.
G Reversal of the battery leads will dam-
age the rectifier.
G Connect the RED lead first when
installing the battery and disconnect
the RED lead last when removing it.
Otherwise, the electrical system can
be damaged.
G The electrical contacts of the battery
and cables must be clean and properly
connected, or the battery will not start
the engine.
@
Connect the RED lead to the POSITIVE (+)
terminal first.
Then connect the BLACK lead to the NEGA-
TIVE (-) terminal.
1 Red lead
2 Black lead
3 Battery
EMU01280
Disconnecting the Battery
Disconnect the BLACK lead from the NEGA-
TIVE (-) terminal first. Then disconnect the
RED lead from the POSITIVE (+) terminal.
4-31
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00408
CHECKING BOLTS AND NUTS
1) Check that bolts securing the cylinder
head and engine and the nut securing
the flywheel are tightened with their
specified tightening torque.
2) Check the tightening torque of other
bolts and nuts.
4-32
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01172
CLEANING COOLING-WATER
PASSAGES
Flushing device equipped model
Perform this procedure right after operation
for the most thorough flushing.
1) After shutting off the engine, unscrew
the garden-hose connector 2 from the
fitting 1 on the bottom cowling.
2) Screw the garden-hose connector 2
onto a garden hose 3 which is con-
nected to a fresh-water supply.
3) With the engine off, turn on the water
tap and let the water flush through the
cooling passages for about 15 minutes.
Turn off the water and disconnect the
garden hose 3.
4) When flushing is complete, reinstall the
garden-hose connector 2 on the fitting
1 on the bottom cowling. Tighten the
connector securely.
CAUTION:
@
Do not leave the garden-hose connector
loose on the bottom cowling fitting or let
the hose hang free during normal opera-
tion. Water will leak out of the connector
instead of cooling the engine, which can
cause serious overheating. Be sure the
connector is tightened securely on the
fitting after flushing the engine.
@
NOTE:
@
G When flushing the engine with the boat in
the water, tilting up the engine until it is
completely out of the water will achieve
better results.
G Refer to cooling system flushing instruc-
tions in “TRANSPORTING AND STOR-
ING OUTBOARD MOTOR”.
@
4-33
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01635
CHECKING TOP COWLING
Check the fitting of the top cowling by push-
ing it with both hands.
If the fitting is loose have it repaired by a
Yamaha dealer.
EMU00409
MOTOR EXTERIOR
EMU00410
Cleaning the Outboard Motor
After use, wash the exterior of the outboard
with fresh water.
Flush the cooling system with fresh water.
NOTE:
@
Refer to Flushing Cooling System instruc-
tions in “TRANSPORTING AND STORING
OUTBOARD MOTOR”.
@
EMU00412
Checking Painted Surface of Motor
Check the motor for scratches, nicks, or flak-
ing paint. Areas with damaged paint are
more likely to corrode. If necessary, clean
and paint the areas. A touch-up paint is
available from a Yamaha dealer.
EMU00413
COATING THE BOAT BOTTOM
A clean hull improves boat performance.
The boat bottom should be kept as clean of
marine growths as possible. If necessary,
the boat bottom can be coated with an anti-
fouling paint approved for your area to inhibit
marine growth.
Do not use anti-fouling paint which includes
copper or graphite. These paints can cause
more rapid engine corrosion.
4-34
Download from Www.Somanuals.com. All Manuals Search And Download.
E
-MEMO-
4-35
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00414
Chapter 5
TROUBLE RECOVERY
TROUBLESHOOTING ...............................5-1
TEMPORARY ACTION IN
EMERGENCY .............................................5-4
IMpact damage ........................................5-4
Running single engine .............................5-4
Power trim/tilt will not operate..................5-5
Treatment of submerged motor...............5-6
5
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01663¯
TROUBLESHOOTING
A problem in the fuel, compression, or ignition systems can cause poor starting, loss of
power, or other problems. The troubleshooting chart describes basic checks and possible
remedies. (This chart covers all Yamaha outboard motors. Therefore, some items may not
apply to your model.)
If your outboard motor requires repair, bring it to a Yamaha dealer.
Trouble
Possible Cause
Remedy
1. Battery capacity weak or low.
1. Check battery condition. Use battery of
recommended capacity.
2. Battery connections loose or corroded.
3. Fuse for electric start circuit blown.
2. Tighten battery cables and clean bat-
tery terminals.
3. Check for cause of electric overload
and repair. Replace fuse with one of
correct amperage.
A. Starter will not
operate.
4. Starter components faulty.
4. Have serviced by a Yamaha dealer.
5. Engine stop switch lanyard not 5. Attach lanyard.
attached.
6. Shift lever in gear.
6. Shift to neutral.
1. Fuel tank empty.
1. Fill tank with clean, fresh fuel.
2. Fill tank with clean, fresh fuel.
3. Clean or replace filter.
2. Fuel contaminated or stale.
3. Fuel filter clogged.
4. Starting procedure incorrect.
5. Fuel pump malfunctions.
6. Spark plug(s) fouled or incorrect type.
4. Read “STARTING ENGINE” section.
5. Have serviced by a Yamaha dealer.
6. Inspect spark plug(s). Clean or replace
with recommended type.
B. Engine will not start
(Starter operates).
7. Spark plug cap(s) fitted incorrectly.
7. Check and re-fit cap(s).
8. Poor connections or damaged ignition 8. Check wires for wear or breaks. Tighten
wiring.
all loose connections. Replace worn or
broken wires.
9. Ignition parts faulty.
9. Have serviced by a Yamaha dealer.
10. Engine stop switch lanyard not 10. Attach lanyard.
attached.
11. Engine inner parts damaged.
11. Have serviced by a Yamaha dealer.
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
E
Trouble
Possible Cause
Remedy
1. Spark plug(s) fouled or incorrect type.
1. Inspect spark plug(s). Clean or replace
with recommended type.
2. Fuel system obstructed.
2. Check for pinched or kinked fuel line or
other obstructions in fuel system.
3. Fuel contaminated or stale.
4. Fuel filter clogged.
3. Fill tank with clean, fresh fuel.
4. Clean or replace filter.
5. Failed ignition parts.
5. Have serviced by a Yamaha dealer.
6. Find and correct cause of warning.
7. Inspect and adjust as specified.
6. Warning system activated.
7. Spark plug gap incorrect.
C. Engine idles
irregularly or stalls.
8. Poor connections or damaged ignition 8. Check wires for wear or breaks. Tighten
wiring.
all loose connections. Replace worn or
broken wires.
9. Specified engine oil not used.
10. Thermostat faulty or clogged.
11. Fuel pump damaged.
9. Check and replace oil as specified.
10. Have serviced by a Yamaha dealer.
11. Have serviced by a Yamaha dealer.
12. Return to normal operating position.
13. Connect correctly.
12. Motor angle too high.
13. Fuel joint connection incorrect.
14. Battery lead disconnected.
1. Cooling system clogged.
2. Engine oil level low.
14. Connect securely.
1. Check water intake for restriction.
2. Fill oil tank with specified engine oil.
3. Specified engine oil not used.
3. Check and replace oil with specified
type.
4. Engine oil contaminated or deterio- 4. Replace oil with fresh, specified type.
rated.
D. Warning buzzer
sounds or indicator
lamp lights.
5. Oil filter clogged.
5. Have serviced by a Yamaha dealer.
6. Have serviced by a Yamaha dealer.
6. Oil feed/injection pump malfunctions.
7. Load on boat improperly distributed.
7. Distribute load to place boat on an even
plane.
8. Water pump/thermostat faulty.
8. Have serviced by a Yamaha dealer.
5-2
Download from Www.Somanuals.com. All Manuals Search And Download.
E
Trouble
Possible Cause
1. Propeller damaged.
Remedy
1. Have propeller repaired or replaced.
2. Propeller pitch or diameter incorrect.
2. Install correct propeller to operate out-
board at its recommended speed
(r/min) range.
3. Trim angle incorrect.
3. Adjust trim angle to achieve most effi-
cient operation.
4. Motor mounted at incorrect height on 4. Have motor adjusted to proper transom
transom.
height.
5. Warning system activated.
6. Boat bottom fouled with marine growth.
7. Spark plug(s) fouled or incorrect type.
5. Find and correct cause of warning.
6. Clean boat bottom.
7. Inspect spark plug(s). Clean or replace
with recommended type.
8. Weeds or other foreign matter tangled 8. Remove foreign matter and clean lower
on gear housing.
unit.
9. Fuel system obstructed.
9. Check for pinched or kinked fuel line or
other obstructions in fuel system.
E. Engine power loss.
10. Fuel filter clogged.
10. Clean or replace filter.
11. Fuel contaminated or stale.
12. Spark plug gap incorrect.
11. Fill tank with clean, fresh fuel.
12. Inspect and adjust as specified.
13. Poor connections or damaged ignition 13. Check wires for wear or breaks. Tighten
wiring.
all loose connections. Replace worn or
broken wires.
14. Failed ignition parts.
14. Have serviced by a Yamaha dealer.
15. Specified engine oil not used.
15. Check and replace oil with specified
type.
16. Thermostat faulty or clogged.
17. Fuel pump damaged.
16. Have serviced by a Yamaha dealer.
17. Have serviced by a Yamaha dealer.
18. Connect correctly.
18. Fuel joint connection incorrect.
19. Heat range of spark plug incorrect.
19. Inspect spark plug and replace it with
recommended type.
1. Propeller damaged.
1. Have propeller repaired or replaced.
2. Have serviced by a Yamaha dealer.
2. Propeller shaft damaged.
3. Weeds or other foreign matter tangled 3. Remove and clean propeller.
on propeller.
F. Engine vibrates
excessively.
4. Motor mounting bolt loose.
4. Tighten bolt.
5. Steering pivot loose or damaged.
5. Tighten or have serviced by a Yamaha
dealer.
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00416
TEMPORARY ACTION IN
EMERGENCY
EMU01492
IMPACT DAMAGE
WARNING
@
The outboard motor can be seriously
damaged by a collision while operating
or trailering. Damage could make the
outboard motor unsafe to operate.
@
If the outboard motor hits any object in the
water, follow the procedure below.
1) Stop the engine immediately.
2) Inspect the control system and all com-
ponents for damage. Also, inspect the
boat for damage.
3) Whether damage is found or not, return
to the nearest harbor slowly and care-
fully.
4) Have a Yamaha dealer inspect the out-
board motor before operating it again.
EMU00418
RUNNING SINGLE ENGINE
Using only one of the engines in case of an
emergency, be sure to keep the unused one
tilted up and operate the other engine at low
speed.
CAUTION:
@
If the boat is operated with one engine in
the water but not running, water may run
into the exhaust pipe due to wave action,
causing engine trouble.
@
NOTE:
@
When you are maneuvering at low speed,
such as near a dock, it is recommended that
both engines be running with one in neutral
gear if possible.
@
5-4
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00419
POWER TRIM/TILT WILL NOT
OPERATE
If the engine cannot be tilted up or down
with the power trim and tilt because of a dis-
charged battery or a failure with the power
trim and tilt unit, the engine can be tilted
manually.
1 Manual valve screw
EMU00421¯
1) Loosen the manual valve screw counter-
clockwise until it stops.
2) Put the engine in the desired position,
then tighten the manual valve screw
clockwise.
5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU01511
TREATMENT OF SUBMERGED
MOTOR
If the outboard motor is submerged, immedi-
ately take it a Yamaha dealer. Otherwise,
some corrosion may begin almost immedi-
ately.
If you cannot immediately take the outboard
motor to a Yamaha dealer, follow the proce-
dure below in order to minimize engine dam-
age.
EMU00449¯
1) Thoroughly wash away mud, salt, sea-
weed, etc. with fresh water.
2) Remove the spark plugs and face the
spark plug holes downward to allow any
water, mud or contaminants to drain.
3) Drain the fuel from the vapor separator,
fuel filter and fuel line.
4) Take the outboard motor to a Yamaha
dealer as soon as possible.
CAUTION:
@
Do not attempt to run the motor until it
has been completely inspected.
5-6
Download from Www.Somanuals.com. All Manuals Search And Download.
E
-MEMO-
5-7
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00450
Chapter 6
INDEX
INDEX ..........................................................6-1
6
Download from Www.Somanuals.com. All Manuals Search And Download.
E
EMU00451
Exhaust leakage............................................ 4-23
Extracting the oil with an oil changer
INDEX
(normal oil change)........................................ 4-19
F
A
Adjusting trim angle ....................................... 3-12
Approval label of emission control certificate... 1-2
B
Basic boating rules (rules of the road)............. 1-7
Battery care ..................................................... 4-8
Battery requirement ....................................... 1-14
Bow down ...................................................... 3-13
Bow up........................................................... 3-13
Breaking in (running in) engine........................ 3-2
C
Flushing cooling system and fogging engine... 4-5
Fuel.................................................................. 3-3
Fueling instructions........................................ 1-11
G
Changing gear oil........................................... 4-27
Checking bolts and nuts ................................ 4-32
Checking fuel system..................................... 4-16
Checking painted surface of motor................ 4-34
Checking points after starting engine .............. 3-8
Checking power trim and tilt system.............. 4-24
Checking propeller......................................... 4-25
Checking the engine oil level........................... 3-4
Checking top cowling .................................... 4-34
Checking wiring and connectors.................... 4-23
Checkpoints................................................... 4-16
Cleaning and adjusting spark plug................. 4-14
Cleaning and anti-corrosion measure.............. 4-7
Cleaning cooling-water passages.................. 4-33
Cleaning the outboard motor ......................... 4-34
Clock.............................................................. 2-14
Coating the boat bottom ................................ 4-34
Connecting the battery................................... 4-31
Controls ........................................................... 3-3
Crossing........................................................... 1-8
Cruising in other conditions ........................... 3-17
Cruising in salt water ..................................... 3-17
D
Digital speedometer....................................... 2-13
Digital tachometer.......................................... 2-10
Disconnecting the battery .............................. 4-31
Draining the oil by removing the oil
drain plug....................................................... 4-21
E
Electric start model .......................................... 3-7
Emission control information............................ 1-2
Engine.............................................................. 3-4
Engine oil....................................................... 1-13
Engine oil leakage ......................................... 4-23
H
I
Impact damage................................................ 5-4
Index................................................................ 6-1
Inspecting and replacing anode(s) ................ 4-28
Inspecting fuel filter........................................ 4-17
K
L
Low oil pressure warning............................... 2-22
Low oil pressure warning indicator ................ 2-12
Lubrication....................................................... 4-6
M
Main components ............................................ 2-1
Main switch...................................................... 2-4
Maintenance chart......................................... 4-11
Manufactured date label.................................. 1-2
Meeting............................................................ 1-8
Motor exterior ................................................ 4-34
N
Narrow channels and bends............................ 1-9
6-1
Download from Www.Somanuals.com. All Manuals Search And Download.
E
Neutral iInterlock trigger................................... 2-3
T
Neutral throttle lever ........................................ 2-4 Tachometer ................................................... 2-10
New technology; (4-stroke/HPDI) EM.............. 1-2 Temporary action in emergency...................... 5-4
North american models.................................... 1-2 “The general prudential rule” ........................... 1-7
O
Oil .................................................................... 3-3 Throttle friction adjusting screw....................... 2-7
One star - low emission ................................... 1-3 Tilting up/down .............................................. 3-14
Operations of controls and other functions...... 2-2 Tilt support lever............................................ 2-19
Other special situations ................................... 1-9 Top cowling lock levers ................................. 2-20
Outboard motor serial number......................... 1-1 Trailering outboard motor ................................ 4-3
Overheat warning .......................................... 2-21 Transporting and storing outboard motor ........ 4-3
Overheat warning indicator............................ 2-12 Treatment of submerged motor....................... 5-6
Overtaking ....................................................... 1-8 Trim meter ..................................................... 2-11
P
Periodic maintenance .................................... 4-10 Trim tab ........................................................... 2-8
Power trim/tilt switch........................................ 2-9 Trip meter ...................................................... 2-14
Power trim/tilt switches .................................... 2-6 Troubleshooting............................................... 5-1
Power trim/tilt will not operate.......................... 5-5 Twin engine speed synchronizer................... 2-19
Pre-operation checks....................................... 3-3 Two stars - very low emission ......................... 1-3
Procedure for remote control model ................ 3-6
W
Procedure for tilting down.............................. 3-16 Warming up engine ......................................... 3-8
Procedure for tilting up................................... 3-15 Warning indicators......................................... 2-15
Propeller checking point ................................ 4-25 Warning labels................................................. 1-6
Propeller selection ......................................... 1-15 Warning system............................................. 2-21
R
Reading buoys and other markers................... 1-9 Water separator warning indicator................. 2-19
Remote control ................................................ 2-2
Remote control lever........................................ 2-3
Removing the propeller.................................. 4-26
Replacement parts......................................... 4-10
Replacing fuse............................................... 4-22
Reverse ........................................................... 3-9
Rules when encountering vessels ................... 1-8
Running single engine ..................................... 5-4
S
Safety information............................................ 1-4
Sailing vessel right-of-way............................... 1-9
Shifting............................................................. 3-9
Specification data ............................................ 4-1
Speedometer ................................................. 2-13
Stand-on vessel............................................... 1-7
Star labels........................................................ 1-3
Start-in-gear protection.................................. 1-16
Starting engine................................................. 3-5
Steering and sailing rules and sound
signals.............................................................. 1-7
Stopping engine............................................. 3-10
Storing outboard motor.................................... 4-4
6-2
Download from Www.Somanuals.com. All Manuals Search And Download.
EMU01599
IMPORTANT WARRANTY INFORMATION FOR U.S.A. AND
CANADA
Welcome to the Yamaha Family!
Congratulations on the purchase of your new Yamaha marine power. Yamaha is com-
mitted to exceptional customer satisfaction, and we want your ownership experience
to be a satisfying one. Please read the following warranty information to help ensure
satisfaction with your Yamaha.
Yamaha is ready to stand behind your purchase with strong warranty coverage. To be sure
you receive all the benefits of warranty, please take the following steps:
1. Be sure your new Yamaha is registered for warranty. Your boat dealer should do this at
the time of sale. Make sure your dealer gives you a copy of the completed Yamaha reg-
istration card for your records. If you are unsure whether or not your Yamaha is regis-
tered, complete the Warranty Registration card found inside the cover of the Owner’s
Manual. Mail it to the distributor for the country in which you live (see step 6 for the cor-
rect address). If your Yamaha is not properly registered, a warranty repair could be
unnecessarily delayed while registration records are checked.
2. Read the Limited Warranty statement which follows these instructions. This warranty
applies to Yamaha outboard motors sold in the United States, whether purchased sepa-
rately or when supplied as original equipment by a boat builder. The terms also apply to
original equipment packages sold in Canada, with coverage provided by Yamaha Motor
Canada (see ‘‘Warranty Guide’’ for Canadian models). This warranty explains the condi-
tions of the warranty, including the obligations that your dealer and you as the owner
have under the warranty. For example, your Yamaha outboard must receive a proper
pre-delivery inspection (PDI) by the selling dealer. Failure to take this important step
could jeopardize warranty coverage!
3. If you need warranty repairs, you must take your Yamaha outboard to an authorized
Yamaha outboard dealer. Be aware that not all selling boat dealers are authorized
Yamaha dealers. Only authorized dealers have the factory training, special tools, and
Yamaha support needed to perform warranty repairs.
4. If you are away from home, or your selling dealer is not an authorized Yamaha dealer,
use the following toll-free numbers to find the nearest Yamaha dealer.
United States Dealer Locations:1-800-692-6242
Canada Dealer Locations:
1-800-267-8577
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Your warranty applies specifically to repairs made in the country of purchase. If your
U.S.-purchased Yamaha needs warranty service while in Canada, or your Canadian
purchased Yamaha needs service while in the United States, Yamaha will assist the
local dealer whenever possible. However, some products available in one country may
not be sold or serviced in the other.
6. If you need any additional information about your Yamaha or warranty coverage which
your dealer cannot provide, please contact us directly.
Yamaha Motor Corporation, U.S.A.
P.O. Box 6555
Cypress, CA 90630
Attention: Customer Relations Department
Telephone No.
Fax No.
(714) 761-7439
(714) 761-7559
Yamaha Motor Canada Ltd.
480 Gordon Baker Road
Toronto, Ontario
M2H 3B4
Attention: Customer Relations Department
Telephone No.
Fax No.
(416) 498-1911
(416) 491-3122
Download from Www.Somanuals.com. All Manuals Search And Download.
EMU01404
YAMAHA MOTOR CORPORATION, U.S.A. FOUR-STROKE
OUTBOARD MOTOR THREE-YEAR LIMITED WARRANTY
Yamaha Motor Corporation, U.S.A. hereby warrants that new Yamaha 1999-or-later model four-stroke outboard motors originally distrib-
uted by Yamaha Motor Corporation, U.S.A. will be free from defects in material and workmanship for the period of time stated herein, sub-
ject to certain stated limitations. Warranty coverage for outboards distributed by non-US Yamaha affiliated companies may be different.
PERIOD OF WARRANTY. Any new Yamaha 1999-or-later model four-stroke outboard motor purchased and registered with Yamaha
Motor Corporation, U.S.A. for pleasure use in the United States, will be warranted against defects in material or workmanship for a period
of three (3) years from the date of purchase, subject to exclusions noted herein. Any Yamaha outboard motor purchased and utilized for
commercial applications will be warranted for a period of one (1) year from the date of purchase, subject to exclusions noted herein.
Yamaha peripheral equipment included with the motor, such as gauges, fuel tanks, and hoses, remote control boxes, and wiring external
from the motor unit, will be warranted for one (1) year from the date of purchase of either pleasure or commercial use. Replacement parts
used in warranty repairs will be warranted for the balance of the applicable warranty period.
The second and third year of warranty (if applicable) shall be limited to covering the cost of parts and labor for major components only. The
major components covered are:
Power Unit Section
G Power Head
G Intake Manifold
G Carburetor Assembly and its Related Components
G Fuel Injection System and its Related Components
G Fuel and Oil Pump Assemblies
G Ignition System (Standard and Microcomputer)
Lower Unit Section
G Exhaust System
G Upper Casing
G Lower Unit Assembly
Bracket Section
G Bracket System
G Power Trim and Tilt Assembly
WARRANTY REGISTRATION. To be eligible for warranty coverage, the outboard motor must be registered with Yamaha Motor Corpora-
tion, U.S.A. Warranty registration can be accomplished by any authorized Yamaha Outboard Motor Dealer. Upon receipt of the registra-
tion, an Owner’s Warranty Card will be sent by Yamaha to the registered purchaser.
OBTAINING REPAIRS UNDER WARRANTY. To receive repairs under this warranty, a valid Owner’s Warranty Card must be presented to
an authorized Yamaha Outboard Motor Dealer.
During the period of warranty, any authorized Yamaha outboard dealer will, free of charge, repair or replace, at Yamaha’s option, any parts
adjudged defective by Yamaha due to faulty workmanship or material from the factory. All replaced parts will become the property of
Yamaha Motor Corporation, U.S.A.
CUSTOMER’S RESPONSIBILITY. Under the terms of this warranty, the customer will be responsible for ensuring that the outboard motor
is properly operated, maintained, and stored as specified in the applicable Owner’s Manual.
The owner of the outboard motor shall give notice to an authorized Yamaha Outboard Motor Dealer of any and all apparent defects within
ten (10) days of discovery and make the motor available at that time for inspection and repairs at the dealer’s place of business.
GENERAL EXCLUSIONS FROM WARRANTY. This warranty will not cover the repair of damage if the damage is a result of abuse or
neglect of the product. Examples of abuse and neglect include, but are not limited to:
1.
2.
Racing or competition use, modification of original parts, abnormal strain.
Lack of proper maintenance and off season storage as described in the Owner’s Manual, installation of parts or accessories that are
not equivalent in design and quality genuine Yamaha parts.
3.
4.
5.
6.
Operation of the motor at an rpm other than specified, use of lubricants or oils that are not suitable for outboard motor use.
Damage as a result of accidents, collisions, contact with foreign materials, or submersion.
Growth of marine organism on motor surfaces.
Normal deterioration.
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFIC PARTS EXCLUDED FROM WARRANTY. Parts replaced due to normal wear or routine maintenance such as oil, spark plugs,
shear pins, propellers, hubs, fuel and oil filters, brushes for the starter motor and power tilt motor, water pump impellers, and anodes, are
not covered by warranty.
Charges for removal of the motor from a boat and transporting the motor to and from an authorized Yamaha Outboard Motor Dealer are
excluded from warranty coverage.
Specific parts excluded from the second and third year of warranty (if applicable) are:
G Top and Bottom Cowling
G Electric Components (other than ignition system)
G Rubber Components (such as hoses, tubes, rubber seals, fittings, and clamps)
TRANSFER OF WARRANTY. Transfer of the warranty from the original purchaser to any subsequent purchaser is possible by having the
motor inspected by an authorized Yamaha Outboard Motor Dealer and requesting the dealer to submit a change of registration to Yamaha
Motor Corporation, U.S.A. within ten (10) days of the transfer.
YAMAHA MOTOR CORPORATION, U.S.A. MAKES NO OTHER WARRANTY OF ANY KIND, EXPRESSED OR IMPLIED. ALL
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WHICH EXCEED THE OBLIGA-
TIONS AND TIME LIMITS STATED IN THIS WARRANTY ARE HEREBY DISCLAIMED BY YAMAHA MOTOR CORPORATION, U.S.A.
AND EXCLUDED FROM THIS WARRANTY.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS
MAY NOT APPLY TO YOU. ALSO EXCLUDED FROM THIS WARRANTY ARE ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES
INCLUDING LOSS OF USE. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUEN-
TIAL DAMAGES, SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
YAMAHA MOTOR CORPORATION, U.S.A.
Post Office Box 6555
Cypress, California 90630
Download from Www.Somanuals.com. All Manuals Search And Download.
EMU01178
IMPORTANT WARRANTY INFORMATION IF YOU USE YOUR
YAMAHA OUTSIDE U.S.A. OR CANADA
Welcome to the Yamaha Family!
Congratulations on the purchase of your new Yamaha marine power. Yamaha is com-
mitted to exceptional customer satisfaction, and we want your ownership experience
to be a satisfying one. Please read the following warranty information to help ensure
satisfaction with your Yamaha.
This model was manufactured as a U.S.A. specification model, and the warranty statement
shown in this manual is for market. To receive the benefits of the warranty that applies to the
country in which you use your Yamaha, please note the following information.
1. The warranty on this model is the same as equivalent models sold in the country where
you will receive service. If you need more information about your warranty coverage or
your Yamaha outside the U.S.A. or Canada, please contact an authorized Yamaha
dealer in your country.
2. Keep a copy of your sales contract or invoice for the purchase of your Yamaha and
present it if you need warranty repairs. This document should show the date of pur-
chase, which is important evidence the repairing dealer will need to be sure your
Yamaha is covered by warranty.
3. If your Yamaha needs warranty repairs, contact an authorized Yamaha dealer in the
country where you are. He will explain how to get warranty service in that country.
4. This Yamaha model may not be sold in some countries. Therefore, in some cases your
local dealer may not have all the parts or service information he may need, which may
unavoidably delay repairs. If this happens, we thank you for your understanding and
assure you we will attempt to resolve the situation as quickly as possible.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|