Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
DIGITAL TELEVISION TRANSITION NOTICE
DIGITAL TELEVISION TRANSITION NOTICE
This device contains a digital television tuner, so it should receive digital over the air
TV programming, with a suitable antenna, after the end of full-power analog TV
broadcasting in the United States on June 12, 2009. The nationwide switch to digital
television broadcasting will be complete on June 12, 2009, but your local television
stations may switch sooner. After the switch, analog-only television sets that receive
TV programming through an antenna will need a converter box to continue to receive
over-the-air TV. Watch your local stations to find out when they will turn off their
analog signal and switch to digital-only broadcasting.
For more information, call the FCC at 1-888-CALL-FCC (1-888-225-5322) or see
the NTIA at 1-888-DTV-2009.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT INFORMATION
IMPORTANT INFORMATION
To reduce the risk of fire or electric shock:
•
•
Do not expose this product to rain or moisture.
Do not remove the rear cover. There are no user-serviceable parts inside.
Refer all servicing requirements to qualified service personnel.
•
The plug should be connected to a mains socket outlet with a protective
earthing connection.
Warnings
The lightning flash with arrowhead inside an equilateral
triangle symbol is intended to alert the user to the presence
of uninsulated dangerous voltage within the product's
enclosure that may be of sufficient magnitude to constitute a
risk of electric shock.
The exclamation inside an equilateral triangle symbol is intended to
alert the user to related operating and maintenance instructions in
the user documentation accompanying the product.
WARNING!
This device must be operated with the original power supply.
CAUTION:
The power supply outlet should be located near the LCD TV and should be easily
accessible.
Always use the appropriate AC cord that is certified for your specific country.
Some examples are listed below:
•
•
•
USA – UL
Canada – CSA
Japan – Electric Appliance Control Act
2
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT INFORMATION
NOTICES
Important Notices Concerning Power Cord Selection
The specific power cord for this LCD TV is enclosed and has been selected
according to the country of destination. Use the enclosed power cord to prevent
electric shock. Observe the following guidelines if it is necessary to replace the
original cord set, or if there is no cord set enclosed. The female receptacle of the
cord set must meet IEC-60320 requirements and should look like Figure A1 below:
Figure A2
Figure A1
For the United States and Canada
In the United States and Canada the male plug is a NEMA5-15 style (Figure A2),
UL-listed, and CSA-labeled. For LCD TVs that are to be placed on a desk or table,
type SVT or SJT cord sets may be used. For LCD TVs that are to be placed directly
on the floor, only SJT type cord sets may be used. The cord set must be selected
according to the current rating for the LCD TV. Consult the table below for the
selection criteria of power cords used in the United States and Canada.
Cord Type Size of Conductor in Cord Maximum Unit Current Rating
18 AWG
16 AWG
14 AWG
18 AWG
17 AWG
10 Amps
12 Amps
12 Amps
10 Amps
12 Amps
SJT
SVT
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT INFORMATION
FCC COMPLIANCE STATEMENT
This equipment has been tested and complies with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy, and may cause
harmful interference to radio communications if not installed and used in accordance
with the instructions. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the distance between the LCD TV and the receiver.
Connect the LCD TV to an outlet on a circuit separate from to which the
receiver is connected.
•
if the interference persists even after performing the above measures,
consult the Westinghouse Service Center or an experienced radio/TV
technician for assistance.
FCC Warning
To assure continued FCC compliance, use a grounded power supply cord and the
provided shielded video interface cable with bonded ferrite cores. If a BNC cable is
used, use only a shielded BNC (5) cable. Also, any unauthorized changes or
modifications not expressly approved by the manufacturer will void the user's
authority to operate this device.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT INFORMATION
IMPORTANT SAFETY INSTRUCTIONS
Make sure to note and follow all warnings and instructions marked on the LCD TV.
Observe the following safety instructions.
•
•
•
•
•
•
•
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
•
•
Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of the obsolete outlet.
•
Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
•
•
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
•
•
Unplug this apparatus during lightning storms or when unused for long
periods of time.
Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT INFORMATION
Circuit Overload
Do not overload wall outlets, extension cords, or power strips. This can result in a fire
or electronic shock.
Power Cord Protection
Power supply cords should be routed so that they are not likely to be walked on or
pinched by items placed upon or against them. Periodically inspect the cords for
damage. Install the LCD TV near a wall socket outlet where the power cord can be
readily accessed.
Ventilation
The slots and openings on the cabinet are provided for necessary ventilation. To
ensure reliable operation of the LCD TV and to protect it from overheating, these
slots and openings must never be blocked or covered.
Never cover the slots and openings with a cloth or other materials.
Do not block the openings by placing the LCD TV on a bed, sofa,
rug or other similar surface.
Do not place the LCD TV in a built-in installation such as a
bookcase or a rack unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
Safety: Lamp Disposal
Lamp(s) inside this product contain mercury and must be recycled or disposed of
according to local, state or federal laws. For more information, contact the electronic
6
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT INFORMATION
WARNINGS AND PRECAUTIONS
•
•
Do not orient the LCD TV towards direct sunlight to reduce glare.
If the LCD TV will not be used for a long period of time, unplug the unit and
remove the batteries from the remote control.
•
•
Avoid touching the display screen by hand or any object.
Never remove the rear cover. The LCD TV interior contains high-voltage
parts. You may be seriously injured if you touch them.
•
•
Always handle the LCD TV with caution when moving it.
Do not install the LCD TV in airtight compartments, or in areas where it can
be exposed to water or high temperature.
•
•
•
Ensure that the area around the LCD TV is clean and free of moisture.
Do not place anything on the LCD TV that can hinder heat dissipation.
Do not place naked flame sources, such as lighted candles, on or near the
LCD TV.
•
•
•
Do not place anything on the LCD TV that can cause liquid to splash on it
(e.g. flower vase).
Do not place heavy objects on the LCD TV, audio/video cables, or power
cord.
If the LCD TV emits smoke, abnormal noise, or a strange odor, immediately
turn it off and contact the Westinghouse Service Center by:
–
–
–
Contacting the Westinghouse Customer Service at (800) 701-0680.
E-mailing us at [email protected].
7
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT INFORMATION
ANTENNA INSTALLATION SAFETY
Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the LCD TV, be sure the
antenna or cable system is grounded to prevent voltage surges and built-up static
charges. Article 810 of the National Electrical Code, ANS/NFPA 70, provides
information on proper grounding of the mast and supporting structure, grounding of
the lead-in wire to an antenna discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode.
Antenna Grounding According to the National
Electrical Code, ANSI/NFPA 70
Antenna lead in wire
Antenna discharge unit
(NEC Section 810-20)
Grounding clamps
Grounding Conductors
(NEC Section 810-21)
Electric service
equipment
Grounding clamps
Power service grounding
electrode system
(NEC Art 250 part H)
NEC: National Electrical Code
Lighting
For added protection for the LCD TV during a lightning storm, or
when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the antenna or cable
system. DO NOT disconnect the antenna or the power cord during
a heavy storm—lightning may strike while you are holding the
cable cord, causing serious injury. Turn off the LCD TV and wait for
the weather to improve.
Power lines
An outside antenna system should not be located in the vicinity of
overhead power lines or other electric light or power circuits, or
where it can fall into such power lines or circuits. When installing an
outside antenna system, extreme care should be taken to keep
from touching such power lines or circuits as contact with them
might be fatal.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT INFORMATION
CLEANING THE LCD TV
•
Make sure the LCD TV is turned off and the power cord is
disconnected from the power outlet.
•
Never spray or pour any liquid directly onto the screen or the
case.
To clean the screen:
1
Wipe the screen with a clean, soft, lint-free cloth. This removes dust and other
particles.
2
If it is still not clean, apply a small amount of non-ammonia, non-alcohol
based glass cleaner onto a clean, soft, lint-free cloth, and wipe the screen.
To clean the case:
1
2
Wipe the case with a soft, dry cloth.
If it is still not clean, apply a small amount of non-ammonia, non-alcohol
based, mild non-abrasive detergent onto a clean, soft, lint-free cloth, then
wipe the surface.
Dolby-Digital Notice
Manufactured under license from Dolby Laboratories. Dolby and the double-D
symbol are registered trademarks of Dolby Laboratories.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
PACKAGE CONTENTS
PACKAGE CONTENTS
40” LCD TV Unit
Remote Control (with 2x AAA batteries)
Z
C.C.
Z
Z
MTS
Favorite
A
B
C
D
ENT
Enter
Input
Vol
Ch
YPbPr1
HDMI1
HDMI2
Video1
Video2
TV
PC
YPbPr2
RMT-11
LCD TV Base
Quick Connect Guide
Power Cord
User Manual
M4 x L10 mm Screw for Base
Warranty Brochure
10
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROL PANEL
CONTROL PANEL
1
2
Menu
Volume
Channel
3
4
5
Source
USB
Power
Item
Description
1. Menu
Display the LCD TV setup screen.
During playback, adjust the volume; in
a menu screen, select an item.
2. Volume +/-
3. Channel +/-
During TV viewing, adjust the channel;
in a menu screen, select an item.
Select the video input source; in a
menu screen, execute a command.
4. Source
5. Power
Toggles the power on and off.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
TERMINALS
TERMINALS
1
6
4
2
10
5
8
7
3
9
USB
Item
Function
Connect the power cord from this outlet to a
power source.
1. AC in
Connect to an external video device such as a
DVD player, game system, cable, or satellite box.
2. HDMI
Connect to a computer or other device with a
VGA output by using a 15-pin VGA cable.
3. PC/VGA
4. PC Audio in
Connect to the audio out port of a computer.
Connect to the AUDIO (R/L) input jacks on
external AV equipment.
5. AUDIO OUT-STEREO
6. SPDIF (optical) audio
out
Connect to an external digital audio receiver.
Connect to an external video device with an
analog signal such as a VCR.
7. Composite video input
8. AV audio input
9. TV turner
Connect to an external audio source.
Connect the LCD TV to an antenna or cable
service.
10. USB Service port
For service only.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL
REMOTE CONTROL
Item
Description
Mute the sound. Press it again to
toggle the sound back on.
1. Mute
Toggle the TV power on and off.
Adjust the LCD screen backlight.
2. Power
3. Backlight
4. MTS
Press to activate Multichannel
Television Sound, Stereo or Mono.
1
2
Toggle the closed caption display on
and off.
3
5
4
6
5. CC
Z
C.C.
Z
Z
MTS
Favorite
A
B
C
D
Set the sleep timer for the LCD TV to
turn off automatically.
Key in the channel number.
Switch to the favorite channels. See
page 23 for details on how to save a
new favorite channel.
6. Sleep zZz
7. Channel keys
8
7
8. Favorite
ENT
9
9. Enter ENT
10. Menu
Execute a channel entry.
10
11
Display the LCD TV setup screen.
12
13
Enter
Switch to a previously bookmarked
channel.
Navigate through the on-screen
menu.
11. Return
14
17
15
16
12. Arrow keys
13. Enter
Input
Vol
Ch
18
Execute a command.
19
21
23
YPbPr1
HDMI1
HDMI2
Video1
Video2
TV
PC
Press to display the Electronic
Program Guide (EPG). It contains the
program information for the channel
you’re watching.
20
22
YPbPr2
14. G
24
26
25
27
Display the input source or channel
information as well as the system
date and time.
RMT-11
15. Info
16. Input
17. Vol +/-
Select the video input source.
Ajust the system volume.
Change the current TV channel.
18. Ch
/
Select the video display format.
Enable YPbPr as the input source.
19. Aspect ratio
20. YPbPr1
Enable TV or HDTV as the input
source.
21. TV
22. HDMI1
23. Video 1
24. YPbPr2
25. PC
Enable HDMI 1 as the input source.
Enable Video 1 as the input source.
Not supported.
Enable VGA as the input source.
Enable HDMI2 as the input source
Enable Video 2 as the input source.
26. HDMI 2
27. Video 2
13
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL OPERATION
REMOTE CONTROL OPERATION
INSTALLING THE REMOTE CONTROL BATTERIES
CAUTIONS:
•
•
Only use AAA batteries.
Do not mix new and old batteries. This may result in cracking or leakage,
which may pose a fire risk or lead to personal injury.
•
Insert batteries according to the (+) and (-) markings. Inserting the
batteries incorrectly may result in cracking or leakage, which may pose a
risk of fire or lead to physical injury.
•
•
•
Dispose of used batteries in accordance with local laws and regulations.
Keep batteries away from children and pets.
When the remote control will not to be used for an extended period,
remove the batteries.
1
Remove the battery cover.
2
Insert the batteries. Make sure the (+) and (–) marks on the batteries match
those inside the compartment.
3
Re-attach the battery cover.
REMOTE CONTROL TRANSMISSION RANGE
Transmission range depends upon the reception angle. The range of coverage is 20°
horizontal/vertical at a distance of 10 feet from the LCD TV.
Z
C.C.
Z
Z
MTS
Favorite
A
B
14
Download from Www.Somanuals.com. All Manuals Search And Download.
LCD TV BASE
LCD TV BASE
CAUTION:
The LCD TV unit may be too heavy for one person to lift. If this is the case,
make sure to ask for assistance in handling the LCD TV to prevent
physical injury and/or damage to the unit.
INSTALLING THE LCD TV BASE
1
2
3
4
5
6
7
8
9
Open the LCD TV carton box.
Remove the LCD TV base.
Remove the plastic bag.
Remove the two top carton stabilizers from the LCD TV.
Remove the protective plastic covering the LCD TV.
Grasp the two sides of the LCD TV and then pull it out of the carton box.
Remove the two bottom carton stabilizers from the LCD TV.
Lay the LCD TV on a clear, flat, and stable surface.
Align the base to the bottom side of the LCD TV and use one M4 x L10 mm
screw to secure it.
U
U
S
S
B
B
10 Carefully orient the LCD TV in an upright position.
B
US
U
S
B
15
Download from Www.Somanuals.com. All Manuals Search And Download.
LCD TV BASE
REMOVING THE LCD TV BASE
If you intend to repack the LCD TV unit (for shipping or storage) or you want to
change the installation to a wall mount option, you must first remove the LCD TV
base.
1
2
3
4
Turn off the LCD TV and all connected devices.
Disconnect the power cord from the LCD TV.
Disconnect all signal cables from the I/O port terminals.
Lay the LCD TV on a clear, flat, and stable surface.
USB
U
SB
5
6
Remove the screw securing the base to the LCD TV.
Detach the base from LCD TV.
U
U
S
B
S
B
7
Pack the screws you removed in step 5 together with the LCD TV base for
future reassembly.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
ANTENNA CONNECTION
ANTENNA CONNECTION
OUTDOOR ANTENNA CONNECTION
Cable TV lead in
VHF, UHF or VHF/UHF
combination antenna
75 ohm coaxial cable (round)
300-75 ohm ADAPTER
RF IN
300 ohm twin-lead (flat)
(Not supplied)
Separate VHF/UHF Antenna
VHF Antenna UHF Antenna
Home Antenna
terminal (75 ohm)
300 ohm twin-lead
COMBINER
(Not supplied)
300 ohm twin-lead
IN OUT
75 ohm coaxial cable
NOTE:
The F-type connector should be finger-tightened only.
When connecting the RF cable to the LCD TV, do not
tighten F-type connector with any tool. If tools are
used, it may cause damage to the LCD TV (e.g.
breaking of internal circuit).
CABLE TV (CTV/DTV) CONNECTION
The unit has a TV tuner (75 ohm coaxial cable connector) located on the rear I/O
panel for easy cable hookup. When connecting the 75 ohm coaxial cable to the unit,
screw the 75 ohm cable to the TV tuner. Some cable TV companies offer premium
pay channels. Since the signals of these channels are scrambled, a cable TV
converter/descrambler is usually provided to the subscriber by the cable TV
company. This converter/descrambler is necessary for normal viewing of the
scrambled channels. (Set your TV to channel 3 or 4. Typically one of these channels
is used. If a channel is unknown, consult your cable TV company.) For more specific
instructions on installing cable TV, consult your cable TV company. One possible
method of utilizing the converter/descrambler provided by your cable TV company is
explained below.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
EXTERNAL DEVICE CONNECTIONS
•
•
A position on the RF switch (not supplied) – You can view all unscrambled
channels by using the TV's channel keys.
B position on the RF switch (not supplied) – You can view the scrambled
channels via the converter/descrambler by using the converter's channel
keys.
RF switch (not supplied)
Two-set
A
signal
OUT
IN
B
Cable TV line
splitter
(Not
supplied)
Cable TV
converter/descrambler
(Not supplied)
EXTERNAL DEVICE CONNECTIONS
IMPORTANT:
•
•
•
Turn off the LCD TV first before connecting an external device to prevent
any possible damage or physical injury.
For more information about external device connections, see the operation
manual of the external device you wish to connect to the LCD TV.
Make sure that the correct cables are connected to each terminal.
Improper cable connections may cause damage to the LCD TV.
You can enjoy picture and sound by connecting various audio-video devices to the
terminals located on the rear and side I/O panels of the LCD TV.
•
•
TV cable input – You can use a commercially available audio/video cable.
Component (YPbPr) input – Picture can be displayed only when a 480i,
480P, 720P or 1080i signal is received.
•
HDMI input – Picture can be displayed only when a 640 x 480, 480P, 720P
or 1080i signal is received. When you connect to the HDMI terminal with a
DVI-HDMI conversion cable, there is a possibility that the picture may not
display correctly.
•
Audio output – You can output audio signals from the LCD TV set through
the analog audio out and SPDIF terminals.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
EXTERNAL DEVICE CONNECTIONS
The following diagram shows the external device connections.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER CONNECTION
POWER CONNECTION
CONNECTING AC POWER
IMPORTANT:
The LCD TV works on a 120 VAC, 60 Hz power input voltage ONLY. Turn
off all connected devices before plugging in the power cord.
Connect the power cord to the LCD TV then to a proper AC outlet.
USB
INITIAL SETUP
Press
on the control panel or on the remote control to turn on the LCD TV. Select
the desired language and select Yes to use the SetupWizard. The SetupWizard
will guide you on how to set up the LCD TV’s operational settings.
Menu
Volume
Channel
Source
Power
Z
C.C.
Z
Z
MTS
Favorite
A
B
20
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS
BASIC OPERATIONS
TURNING THE POWER ON AND OFF
Turning on the power
Press
on the control panel or on the remote control to turn on the LCD TV.
Turning off the power
Press
on the control panel or on the remote control to turn off the LCD TV.
The LED behavior will depend on the enabled Power settings.
Menu
LED Behavior
Turns from amber
Description
When LED Setting
Volume
to blue when power is set to ON.
on and turns from
Channel
blue to amber when
power off.
Source
Remains in blue.
When LED Settings
is set to OFF.
Power
Z
C.C.
Z
Z
MTS
Favorite
A
B
NOTES:
•
If you are not going to use the TV for a long time, be sure to disconnect the
power cord from the wall outlet and remove the batteries from the remote
control.
•
In standby mode, a small amount of electricity is still consumed even when
the power is turned off.
ADJUSTING THE VOLUME
Volume
Mute
Press Vol+ to increase the volume; press Vol-
to decrease the volume.
Z
C.C.
Z
Z
MTS
Mute
Favorite
Input
Press
to turn off the sound. Mute appears
Vol
Ch
Volume
on the volume bar. Press again to turn on the
sound.
YPbPr1
HDMI1
Video1
TV
21
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS
CHANGING CHANNELS
Referred to in the following instructions to change channels.
Using the Ch
/
Buttons
Browse channels
Input
To browse through the available channels, press Ch
/
on
Vol
Ch
the remote control or on the control panel.
YPbPr1
HDMI1
Video1
TV
Using the Channel Keys
Favorite
Selecting channel
A
B
C
D
To change to a certain channel, key in the channel number using
the channel keys and press ENT.
Selecting digital channel
ENT
To select a digital channel, key in the digital channel number using
the channel keys and the • key then press ENT.
Using the Favorite Keys
Z
C.C.
Z
Z
MTS
Selecting favorite channels
Favorite
A
B
C
D
To select a favorite channel, press the Favorite button (A, B, C, or
D) corresponding to the preferred favorite channel.
Saving a channel as a favorite
ENT
1
Display the channel you want to add as a favorite.
2 Press and hold the Favorite channel key for 3 seconds you
want to add the current channel to.
3 The Channel Saved message appears to confirm the new
favorite channel item.
SELECTING THE INPUT SOURCE
There are two ways to select the video input source.
Using the Individual Input Keys
TV, PC, Video, YPbPr, HDMI Keys
YPbPr1
HDMI1
Video1
TV
Press any of the following remote control keys to change the input
YPbPr2
HDMI2
Video2
PC
source: TV, PC, Video, YPbPr, or HDMI.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS
Using the Input Key
Select source using Input Key
Press Input
2 A list of supported video sources is displayed.
Input
Vol
Ch
1
.
YPbPr1
HDMI1
Video1
TV
3 Press
4 Press
/
to select the preferred source.
to switch to the selected input source.
ADJUSTING THE DISPLAY FORMAT
The input source can sometimes affect the way images are displayed on-screen.
You can adjust the display format to view the image properly.
Input
Format Options
Vol
Ch
YPbPr1
HDMI1
HDMI2
Video1
Video2
TV
PC
Press
repeatedly to toggle the display format. As you toggle
YPbPr2
each option on, the actual display will change accordingly. Options
include:
•
•
•
•
Standard: Picture is displayed in its original size.
Fill: Picture is displayed to cover the entire screen.
Overscan: Picture is scaled down to fit the display area.
1:1 Mode: Matches the incoming resolution exactly to the
pixels without any scaling.
ADJUSTING THE LCD BACKLIGHT
Different viewing conditions can affect the quality of the display. You can adjust the
LCD backlight to suit the current viewing condition.
Backlight options
Z
C.C.
Z
Z
MTS
Favorite
A
Press
repeatedly to toggle the Backlight options: Bright
Room, Medium Room, and Dark Room.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
SETUP MENUS
SETUP MENU OPERATION
Use the setup menus to configure the various operational settings of the LCD TV.
Displaying the setup menu screen
Press on the remote control or Menu on the control panel to display the setup
menu screen.
Navigating the setup menu screen
Use the buttons on the remote control or on the control panel to navigate through
the menu screens.
Menu
Volume
Channel
Enter
Source
K
Power
Action
Remote Control
Control Panel
MENU
Display or close the menu bar.
•
Select and display a primary
menu.
Volume +/- then
/
/
then
then
Source
•
•
Adjust sub-menu options.
Select and display a sub-menu.
Channel +/- then
•
Select a menu or a sub-menu
option.
Source
•
Return to the primary menu tab
from a sub-menu screen.
Menu
•
Return to the previous screen.
Apply the selected menu setting or
cycle though available menu
options.
Source
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
AUDIO
Use the Audio sub-menus to configure the audio quality. These settings apply to the
LCD TV speakers only. Any connected audio devices are not affected.
Press
on the remote control or Menu on the control panel to display the setup
menu screen then select Audio to display the Audio sub-menu. The following
options are available: Bass, Treble, Balance, TV Speaker, Audio Presets, and Reset.
Bass
Use Bass to calibrate low-pitched sounds.
Bass
Adjusting Bass
1
Use the
/
keys to select Bass and press
keys on the remote control to adjust the option level.
to save and exit the screen.
.
2 Press the
3 Press
/
Treble
Use Treble to calibrate high-pitched sounds.
Treble
Adjusting Treble
1
Use the
/
keys to select Treble and press
keys on the remote control to adjust the option level.
to save and exit the screen.
.
2 Press the
3 Press
/
29
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
Balance
Use Balance to adjust the sound balance between the L/R speakers.
Balance
Adjusting Balance
1
Use the
/
keys to select Balance and press
keys on the remote control to adjust the option level.
to save and exit the screen.
.
2 Press the
3 Press
/
TV Speaker
Use this sub-menu to toggle the LCD TV speakers on and off.
TV Speaker
ON
OFF
Adjusting TV Speaker
Use the keys to select TV Speaker and press
keys on the remote control to select ON or OFF.
to save and exit the screen.
1
/
.
2 Press the
3 Press
/
30
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
Audio Preset
Use this sub-menu to select one of four preset audio options optimized for different
sounding conditions.
The following options are available:
•
•
•
•
•
Rock: Sets the equalizer to the Rock mode.
Pop: Sets the equalizer to the Pop mode.
Classical: Sets the equalizer to the Classical mode.
Flat: Sets the equalizer to the Flat mode.
Custom: Customizes the equalizer settings.
Adjusting Audio Preset
1
Use the
/
keys to select Audio Preset and press
keys on the remote control to select the desired option.
to save and exit the screen.
.
2 Press the
3 Press
/
Reset
Select Yes on this sub-menu to reset all audio-related settings.
Reset
31
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
VIEW MODE
Use the View Mode sub-menu to select the aspect ratio of the display.
Press
on the remote control or MENU on the control panel to display the setup
menu screen then select View Mode to display the View Mode sub-menu. The
following options are available: Standard, Fill, Overscan, and 1:1 Mode.
View Mode
1:1 Mode
Standard
Fill
Overscan
Standard
Picture is displayed in its original size.
Fill
Picture is displayed to cover the entire screen.
Overscan
Picture is scaled down to fit the display area.
1:1 Mode
Matches the incoming resolution exactly to the pixels without any scaling.
Adjusting View Mode
1
2
Press the
Press
/
keys on the remote control to select the desired option.
to save and to exit the screen.
VIEW MODE (VGA)
Select VGA as your input source and use the View Mode sub-menu to adjust the
display in VGA mode.
Press
on the remote control or MENU on the control panel to display the setup
menu screen then select View Mode to display the View Mode sub-menu. The
following options are available: Aspect Ratio, H. Position, V. Position, Fine Tune, and
Auto Sync.
Aspect Ratio
Use this sub-menu to select the display's aspect ratio in the following options:
32
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
•
1:1 Mode: Matches the incoming resolution exactly to the pixels without any
scaling.
•
•
Standard: Picture is displayed in its original size.
Fill: Picture is displayed to cover the entire screen.
H. Position
Use this sub-menu to adjust the horizontal position of the display.
16:9
A
H. Position
V. Position
Use this sub-menu to adjust the vertical position of the display.
16:9
A
V. Position
Fine Tune
Use this sub-menu to fine tune the display.
16:9
A
Fine Tune
Auto Sync
Use this sub-menu to synchronize the display automatically.
16:9
A
Auto Sync
33
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
TV PROGRAM
Use the TV Program sub-menus to manage the channel list, language sound, and to
scan for available TV channels in your area.
Press
on the remote control or MENU on the control panel to display the setup
menu screen then select TV Program to display the TV Program sub-menu. The
following options are available: Skip List, Channel Edit, MTS, Auto Search, and
Manual Add.
Skip List
Use Skip List to select the channels you want to skip.
Channel Skip List
Clear List
11.0
13.0
16.1
17.0
21.0
22.0
23.0
24.0
:Select
Enter: Confirm
Menu: Exit
Adding Channels to Skip List
1
Use the
/
keys to select Skip List and press
. The Channel Skip
List screen appears.
2 Use the
3 Press
/
keys to select the desired channel.
repeatedly to check (add to the Skip list) or uncheck (clear to
the Skip list) the channels.
4 Repeat steps 2 and 3 to add more channels.
5
Press
to exit the screen.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
Channel Edit
Use Channel Edit to assign a name to a channel.
Channel Name Edit
11.0
13.0
16.1
17.0
21.0
22.0
23.0
24.0
:Select
Enter: Confirm
Menu: Exit
Editing Channel Names
1
Use the
/
keys to select Channel Edit and press
. The Channel
Name Edit screen appears.
2 Use the keys to select the desired channel and press
/
to open
the Edit Name screen.
3 Use the
/
/
/
keys to move the cursor to the desired symbol and
press the
button to enter.
• Select Shift to toggle different symbol tables: uppercase and lowercase
letters, numerals, and special symbols.
• Select Back to backspace.
• Select Clear to delete all typed text.
4 Select Accept when finished.
5 Repeat steps 2, 3, and 4 to add more channels.
6
Press
to exit the screen.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
MTS
Use MTS to select multichannel television sound.
The following options are available:
•
•
•
Mono: Allows mono output (useful when stereo is noisy or inconsistent).
Stereo: Allows stereo sound for superior TV viewing experience.
SAP: Allows second audio program from the speakers while watching a
scene in the original program.
Adjusting MTS
1
Use the
2 Press the
Press
/
keys to select MTS and press
keys on the remote control to select the desired option.
to save and to exit the screen.
.
/
3
Audio Language
Use this sub-menu to select the audio language to English, French, or Spanish.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
Adjusting Audio Language
Use the keys to select Audio Language and press
1
/
.
2 Press the
Spanish.
/
keys on the remote control to select English, French, or
3
Press
to save and
to exit the screen.
Auto Search
Select Auto Search and press
. Two options are available:
•
Cable: Choose this setting if you are receiving TV channels with a CATV
(cable TV).
•
AIR: Choose this setting if you are receiving TV channels with an antenna
(over the air).
Auto Search automatically creates a list of receivable channels for the selected
source.
Manual Add
Use Manual Add to add channels manually.
Channel Add
_
Enter
:Select
Enter: Confirm
Menu: Exit
Adding Channels Manually
1
Use the
/
keys to select Manual Search and press
. The Channel
Add screen appears.
2 Use the Channel keys on the remote control to enter the channel number
and select Enter. Wait a few moment for the TV to search for the channel.
3 When the channel is found, you can select Add to add to channel.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
SETTINGS
Use the Settings sub-menus to configure the LCD TV operational setup and view the
current firmware version.
Press
on the remote control or MENU on the control panel to display the setup
menu screen then select Settings to display the Settings sub-menu. The following
options are available: Date and Time, Closed Captions, Parental Control, OSD
Timeout, OSD Language, Power settings, Reset All, and Version.
Date and Time
Use Date and Time to adjust the current date and time.
Date and Time
Date
Day of Week
Thursday
JAN 1, 2009
Time Zone
Current Time
10:54 AM
Eastern (UTC-5)
Adjust for Daylight Saving Time
Auto Calibration
:Select
Enter: Confirm
Menu: Exit
Adjusting Auto Calibration
1
Use the
2 Press
Calibration.
Press to save and
/
keys to select Date and Time and press
.
repeatedly to check (enable) or uncheck (disable) Auto
3
to exit the screen.
• Enable this option to view the system’s current time.
• Both Date and Current Time are unavailable for adjustments when
Auto Calibration is enabled.
Adjusting Time Zone
1
2
Use the
Use the
/
keys to select Date and Time and press
keys to select Time Zone and press
.
/
.
3 Use the
/
keys to select the desired Time Zone: Samoa, Hawaii,
Alaska, Pacific, Mountain, Central, Eastern, Atlantic, or
Newfoundland.
4
Press
to save and
to exit the screen.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
Adjusting Date and Time
Use the keys to select Date and Time and press
1
/
.
2 Use the
/
keys to select Date or Current Time and press
.
3 Use the
4 Use the
/
keys to select a date or time segment.
keys to adjust the value.
/
5
Press
Adjusting Daylight Saving
Use the keys to select Date and Time and press
2 Press repeatedly to check (enable) or uncheck (disable) Adjust for
to save and
to exit the screen.
1
/
.
Daylight Saving Time.
3
Press to save and
to exit the screen.
Closed Captions
Use Closed Captions to configure the settings for closed captioning in TV programs.
The following options are available:
•
•
•
Closed Captions: Can be set to ON or OFF.
Analog Type: Can be set to CC1,CC2, CC3, CC4, T1, T2, T3, or T4.
Digital Type: Can be set to CS1, CS2, CS3, CS4, CS5, or CS6.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
•
Font: Can be set to As Broadcaster, Style 1, Style 2, Style 3, Style 4,
Style 5, Style 6, or Style 7.
•
•
Size: Can be set to As Broadcaster, Small, Medium, or Large.
Font Color: Can be set to As Broadcaster, Black, White, Green, Blue,
Red, Cyan, Yellow, or Magenta.
•
•
•
•
•
Background Color: Can be set to As Broadcaster, Black, White, Green,
Blue, Red, Cyan, Yellow, or Magenta.
Edge Type: Can be set to As Broadcaster, None, Raised, Depressed,
Uniform, Shadow Left, or Shadow Right.
Edge Color: Can be set to As Broadcaster, Black, White, Green, Blue,
Red, Cyan, Yellow, or Magenta.
Foreground Opacity: Can be set to As Broadcaster, Solid, Translucent,
Transparent, or Flashing.
Background Opacity: Can be set to As Broadcaster, Solid, Translucent,
Transparent, or Flashing.
Adjusting Closed Captions Settings
1
Use the
/
keys to select Closed Captions and press
.
2 Use the
3 Use the
/
keys to select the desired Closed Captions option.
keys to adjust the value.
/
4
Press
to exit the screen.
Parental Control
Use Parental Control to block channels and change the password. You must enter a
six-digit password to use the Parental Control. The factory password is 999999.
Enter Password
~
0
9: Key in password
Enter: Confirm
Menu: Exit
After you enter the correct password, the Parental Control menu is shown. By
default, only the Rating and Change Password submenu are displayed. To display
the hidden submenu, set Rating to ON.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
The following options are available:
•
•
Rating: Select ON/OFF to hide or display the hidden submenu.
Block Unrated: Select ON/OFF to block/unlock all unrated programs.
Adjusting Rating and Block Unrated
1
Use the
/
keys to select Rating or Block Unrated and press
keys to select ON or OFF.
.
2 Use the
/
3
Press
to save and
to exit the screen.
•
TV Rating: Use this sub-menu to customize US TV Rating programs.
Rating
TV-Y
TV-Y7
TV-G
Description
Suitable for young children.
May not be suitable for children under 7.
Suitable for all audiences.
Parental guidance suggested.
Parental guidance suggested for children
under 14.
TV-PG
TV-14
Suitable for mature audiences only; may
be unsuitable for children under 17.
Fantasy violence, combative situations.
Suggestive dialogue.
TV-MA
FV
D
L
L Coarse language.
S
Sexual situations.
V
Violence.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
Adjusting TV Rating
1
Use the
/
keys to select TV Rating and press
.
2 Use the
/
keys to select the desired rating and press
repeatedly
to block or unblock. You can also select Lock All to block all or Unlock All
to unblock all.
3
Press
to exit the screen.
•
MPAA Rating: Use this sub-menu to select the ratings of allowable movies.
Rating
Description
Contains nothing most parents will consider offensive for even
their youngest children to see or hear; suitable for young children.
May contain some material parents might not like to expose to their
young children-material that will clearly need to be examined or
inquired about before children are allowed to view the film.
May contain some scenes of drug use; use of one of the harsher
sexually-derived words may be heard. May be inappropriate for
preteens.
May contain some adult material. Parents are urged to learn more
about the film before letting their children view it.
May contain explicit sex scenes, an accumulation of sexually-
oriented language, and/or scenes of excessive violence. Suitable
for adult audiences only. Rating does not signify that the film is
obscene or pornographic.
G
PG
PG-13
R
NC-17
X
Contains extreme violence or explicit sex; suitable for adult
audiences only.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
Adjusting MPAA Rating
1
Use the
/
keys to select MPAA Rating and press
.
2 Use the
/
keys to select the desired rating and press
repeatedly
to block or unblock.
3
Press to exit the screen.
•
Canada English: Use this sub-menu to select the classification categories
(based on Canadian ratings) of allowable TV programs
and movies.
Rating
Description
E
Exempt shows
Suitable for viewing by children of all
ages.
C
Not suitable for children under 8 years of
age.
C8+
G
PG
Suitable for general audiences.
Parental guidance advised.
Suitable for people 14 years of age or
older.
Suitable for people 18 years of age or
older.
14+
18+
Adjusting Canada English Rating
Use the keys to select Canada English Rating and press
1
/
.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
2 Use the
/
keys to select the desired rating and press
repeatedly
to block or unblock.
3
Press to exit the screen.
•
Canada French: Use this sub-menu to select the ratings of allowable TV
programs and movies. These ratings are based on the
classification categories determined by La Régie du cinéma
du Québec.
Rating
Description
E
Exempt shows
G
For general audiences.
Not suitable for children under 8
years of age.
Not suitable for persons under 13
years of age.
Not suitable for persons under 16
years of age.
Not suitable for persons under 18
years of age.
8 ans +
13 ans+
16 ans+
18 ans+
Adjusting Canada French Rating
1
Use the
/
keys to select Canada French Rating and press
.
2 Use the
/
keys to select the desired rating and press
repeatedly
to block or unblock.
3
Press to exit the screen.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
•
V2.0 (Open V-Chip): V-Chip 2.0 enabled.
•
Channel Block: Channel Block allows you to block channels.
11.0
13.0
16.1
17.0
21.0
22.0
23.0
Adjusting Channel Block
1
Use the
2 Use the
repeatedly to block or unblock.
/
keys to select Channel Block and press
.
/
keys to select the desired channel and press
3
Press
to exit the screen.
•
Change Password: Change Password allows you to change your current
password.
Changing Password
1
Use the
/
keys to select Change Password and press
.
2 Use the Channel keys to enter the current password and press
3 Use the Channel keys to enter the new password and press
.
.
4 Use the Channel keys to enter the new password again for confirmation
and press
.
5
Press
to exit the screen.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
OSD Timeout
Use OSD Timeout to adjust the OSD duration on the screen: 10 sec, 20 sec, or 30
sec.
en
OSD Timeout
10 sec
20 sec
30 sec
Adjusting OSD Timeout
Use the keys to select OSD Timeout and press
1
/
.
2 Press the
sec.
/
keys on the remote control to select 10 sec, 20 sec, or 30
3
Press
to save and
to exit the screen.
OSD Language
Use OSD Language to select the language to display on the screen: English,
French, or Spanish.
en
OSD Language
English
French
Spanish
Adjusting OSD Language
Use the keys to select OSD Language and press
1
/
.
2 Press the
Spanish.
/
keys on the remote control to select English, French or
3
Press
to save and
to exit the screen.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
Power Settings
Use this sub-menu to configure power-related settings for the LCD TV.
The following options are available:
•
VGA port -DPMS: Use this setting to enable or disable VGA port -DPMS.
•
Backlight: Use this setting to select the backlight mode: Bright Room,
Medium Room, or Dark Room.
•
Dynamic Contrast: Use this setting to enable or disable Dynamic Contrast.
Adjusting Power Settings
1
Use the
/
keys to select Power Settings and press
.
2 Use the
3 Use the
4 Press
/
keys to select a desired option.
/
keys to adjust the value.
to exit the screen.
Reset All
Select Yes on this sub-menu to reset all LCD TV operational settings. Do this only if
any of the following conditions occurs:
•
The system fails to respond to the remote control (ensure that the remote
control batteries are still working and you are within the transmission range).
•
•
The new configuration settings cause unexpected results.
You forget the system PIN.
en
Reset All
47
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
Version
Use this sub-menu to view the LCD TV’s serial number and firmware version.
en
Version
48
Download from Www.Somanuals.com. All Manuals Search And Download.
WALL MOUNT OPTION
WALL MOUNT OPTION
The LCD TV has been fitted with VESA FPMPMI compliant mounting holes. These
200 x 100 mm mounting holes allow the unit to be mounted on a wall. Use the four
M6 x L10 mm screws to wall mount the LCD TV.
SB
U
WALL MOUNT INSTALLATION REMINDERS
•
Remove the LCD TV base first before mounting the unit on a wall.
•
It is the user's responsibility to use a UL listed wall mount unit rated to
support the weight of this LCD TV.
•
Please consult qualified contractors for wall mount installation.
CAUTION:
The incomplete or improper mounting of this unit to a wall may cause it to fall down
resulting to property damage and/or potentially serious injury.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
TROUBLESHOOTING
Problem
Corrective Action
•
Make sure the power indicator is illuminated
blue.
•
Make sure the power cord is securely
connected to the AC-in jack and is plugged
into a functional AC outlet. You may want to
plug in another electrical device to the power
outlet to verify that it is supplying the proper
voltage.
No power
Power is suddenly
turned off.
Make sure the sleep timer is turned off.
Use Reset All in Settings menu to reset your
password.
Forgotten PIN
•
•
•
Press only one button at a time.
Remote control
does not work.
Make sure the batteries are properly inserted.
The batteries may already be drained out.
Replace batteries with new ones.
Remote control
code cannot be
detected by a
•
•
Purchase a separate learning remote control.
codes.
universal remote.
•
Make sure the video input cable is properly
connected to the correct terminal, and that the
correct input mode is enabled. To illustrate,
when a VGA cable is connected to display a
computer screen, the PC input mode must be
enabled.
No picture
•
•
Verify that the antenna is properly connected
and that the preferred channel is enabled in
the channel list. Press and select
Channels/Channel List.
Adjust the display settings.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Problem
Corrective Action
•
•
•
Make sure the VGA cable is properly
connected to the LCD TV’s VGA port.
No picture or the No
Signal message
appears when a
VGA cable is
Decrease the video resolution setting on the
computer and try again.
connected.
Adjust the display settings.
Picture is cut off or
appear in a sidebar
screen.
Press
to adjust the Aspect ratio.
•
Check your antenna connection. If necessary,
rotate the antenna and wait up to ten seconds
for a signal.
•
•
Reduce signal splitters and excessively long
cables.
Poor image quality
in TV mode (cutoff
picture, snowy
images).
Replace poor antenna cables and/or
connectors to improve signal quality.
•
•
Press
to adjust the Aspect ratio.
Adjust the Noise Reduction setting in Picture
menu.
•
•
In HDMI mode, make sure the external device
is compatible with the LCD TV.
If any colors (red, green or blue) are missing,
check the video cable to make sure it is
securely connected. Loose or broken pins in
the cable connector could cause an improper
connection.
Wrong, abnormal or
missing colors
•
•
Adjust the Hue, Saturation and Color
Temperature settings in Picture menu.
Connect the TV to another computer and
check if the problem is with the computer
screen.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Problem
Corrective Action
•
Make sure the audio input cable is properly
connected to the correct terminal, and that the
correct input mode is enabled.
•
•
•
The volume may be muted, press or Vol+ key
to turn on the volume.
Adjust the Bass, Treble, and Balance settings
in Audio menu.
No sound
If you are using the TV speakers, make sure
the TV Speakers option is set to On in Audio
menu.
•
If you are using an external audio device,
press and select Audio to make sure the TV
Speakers option is set to Off in Audio menu.
NOTES:
If the problem condition persists even after performing the
recommended corrective actions, contact us by:
•
•
Contacting the Westinghouse Customer Service at (800) 701-0680
or e-mail us at [email protected]
52
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
SPECIFICATIONS
Item
Specification
Model Name
VR-4025
Active Area
(Diagonal, mm)
885.6 x 498.15
1920 x 1080
300
Resolution
Brightness
(Nits, typ)
Panel
Contrast Ratio
(min)
5000:1
Response Time
(min)
7.5ms(g-g)
Aspect Ratio
Display color
1.77 (16:9)
16.7M
•
•
•
•
•
•
•
HDMI x2
AV with R/L Audio x1
VGA with Audio mini jack blue x1
SPDIF Out x1
Audio/Video
Input/Output
Terminals
USB for service x1
Tuner x1
R/L Audio Line Out x1
Speaker Out
AV Timing
10W (2 channels, 10% THD)
480i/p, 720p, 1080i, 1080p
640 x 480 @ 60Hz/75Hz,
800 x 600 @ 60Hz/75Hz,
1024 x 768 @ 60Hz/75Hz,
1280 x 720 @ 60Hz,
PC Timing
1360 x 768 @ 60Hz,
1280 x 1024 @ 60Hz,
1920 x 1080 @ 60Hz
Power Consumption
(Watts)
163W
53
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Item
Specification
Power Consumption
(Standby, Watts)
<1W
With stand:
1007.42 x 689.91 x 228 mm
Dimensions
(WxHxD)
Without stand:
Physical
Specifications
1007.42 x 639.77 x 88.5 mm
Weight (Net)
16.22 kgs (35.73lb)
Weight (Gross) 20.72 kgs (45.64lb)
NOTES:
•
These product specifications are subject to change without user
notification.
•
Do not set your computer graphics card to exceed the unit’s refresh
rates; doing so may cause damage to the LCD TV.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
1506-0FVU000
Download from Www.Somanuals.com. All Manuals Search And Download.
|
