Weed Eater Tiller 186100 User Manual

OWNER'S MANUAL  
MODEL NO. WET6500A  
6.5 HP 17 Inch  
Tiller  
Assembly  
Operation  
Maintenance  
Service and Adjustments  
Storage  
Troubleshooting  
Repair Parts  
For Parts and Service, contact our authorized distributor: call 1-800-849-1297  
For Technical Assistance: call 1-800-829-5886  
®
01029-weedeater  
186100 Rev. 3 06.17.03 TR  
PRINTED IN U.S.A.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PRODUCT SPECIFICATIONS  
CUSTOMER RESPONSIBILITIES  
Read and observe the safety rules.  
Gasoline Capacity:  
3 Quarts (2.8L)  
Unleaded Regular  
Follow a regular schedule in maintaining, caring for  
and using your tiller.  
Oil (API-SF-SJ):  
(Capacity: 20 oz./0.6L)  
SAE 30 (Above 32°F/0°C)  
SAE 5w-30 (Below 32°F/0°C)  
Follow instructions underMaintenanceandStorage”  
sections of this Owner’s Manual.  
Spark Plug :  
(Gap: .030"/0.76mm)  
Champion  
RN4C  
WARNING:Thisunitisequippedwithaninternalcombustion  
engine and should not be used on or near any unimproved  
forest-covered, brush-covered or grass covered land un-  
less the engine’s exhaust system is equipped with a spark  
arrester meeting applicable local or state laws (if any). If a  
spark arrester is used, it should be maintained in effective  
working order by the operator.  
CONGRATULATIONS on your purchase of a new tiller. It  
has been designed, engineered and manufactured to give  
you the best possible dependability and performance.  
Should you experience any problems you cannot easily  
remedy, please contact your nearest authorized service  
center. We have competent, well-trained technicians and  
the proper tools to service or repair this unit.  
In the state of California the above is required by law (Sec-  
tion 4442 of the California Public Resources Code). Other  
statesmayhavesimilarlaws. Federallawsapplyonfederal  
lands. SeeyourAuthorizedServiceCenter/Departmentfor  
spark arrester. Refer to the Repair Parts section of this  
manual for part number.  
Please read and retain this manual. The instructions will  
enable you to assemble and maintain your tiller properly.  
Always observe the “SAFETY RULES”.  
TABLE OF CONTENTS  
MAINTENANCE .....................................................12-14  
SERVICE & ADJUSTMENTS .................................15-18  
STORAGE.................................................................... 19  
TROUBLESHOOTING ................................................. 20  
REPAIR PARTS-TILLER.........................................21-27  
WARRANTY................................................................. 28  
SAFETY RULES ............................................................ 2  
CUSTOMER RESPONSIBILITIES................................. 3  
PRODUCT SPECIFICATIONS....................................... 3  
ASSEMBLY.................................................................4-6  
OPERATION .............................................................7-11  
MAINTENANCE SCHEDULE ...................................... 12  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
Your new tiller has been assembled at the factory with exception of those parts left unassembled for shipping purposes.  
To ensure safe and proper operation of your tiller, all parts and hardware you assemble must be tightened securely. Use  
the correct tools as necessary to insure proper tightness.  
TOOLS REQUIRED FOR ASSEMBLY  
A socket wrench set will make assembly easier. Standard  
wrench sizes are listed.  
FRONT  
(1) Utility knife  
(1) Tire pressure gauge  
(1) Pair of pliers  
LEFT  
RIGHT  
(1) 9/16" wrench  
OPERATOR’S POSITION (See Fig. 1)  
When right or left hand is mentioned in this manual, it  
means when you are in the operating position (standing  
behind tiller handles).  
OPERATOR’S  
POSITION  
FIG. 1  
CONTENTS OF HARDWARE PACK  
(1) Carriage Bolt  
3/8-16 UNC x 1 Grade 5  
(1) Center Locknut  
3/8-16 UNC  
(2) Handle Locks  
(1) Handle Lock Lever  
(1) Hairpin Clip  
(1) Flat Washer 13/32 x 1 x 11 Gauge  
(1) Pivot Bolt  
3/8-16 UNC Grade 5  
Extra Shear Pins & Clips  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
Grasp handle assembly. Hold in “upposition. Be sure  
handle lock remains in gearcase notch. Slide handle  
assembly into position.  
UNPACKING CARTON (See Fig. 2)  
CAUTION: Be careful of exposed  
staples when handling or disposing  
of cartoning material.  
HANDLE ASSEMBLY  
"UP" POSITION  
IMPORTANT:  
WHEN UNPACKING AND ASSEMBLING  
TILLER, BE CAREFUL NOT TO STRETCH OR KINK CABLES.  
While holding handle assembly, cut cable ties securing  
handle assembly to top frame. Let handle assembly  
rest on tiller.  
TIGHTEN HANDLE  
LOCK LEVER TO  
HOLD  
Remove top frame of carton.  
Slowly ease handle assembly up and place on top of  
carton.  
Cut down right hand front and right hand rear corners  
of carton, lay side carton wall down.  
Remove packing material from handle assembly.  
LOOSEN HANDLE  
LOCK LEVER TO  
MOVE  
FIG. 4  
HANDLE  
ASSEMBLY  
Rotatehandleassemblydown.Insertrearcarriagebolt  
first, with bolt head on L.H. side of tiller and loosely  
assemble locknut (See Fig. 5).  
Insert pivot bolt in front part of plate and tighten.  
Cut down remaining corners of carton and lay panels  
flat.  
Lower the handle assembly. Tighten nut on carriage  
bolt bolt so handle moves with some resistance. This  
will allow for easier adjustment.  
Place flat washer on threaded end of handle lock le-  
ver.  
Insert handle lock lever through handle base and  
gearcase. Screw in handle lock lever just enough to  
hold lever in place.  
SHIFT ROD  
FIG. 2  
Insert second handle lock (with teeth inward) in the  
slot of the handle base (just inside of washer).  
With handle assembly in lowest position, securely  
tighten handle lock lever by rotating clockwise. Leav-  
ing handle assembly in lowest position will make it  
easier to remove tiller from carton.  
INSTALL HANDLE (See Figs. 3, 4, and 5)  
Insert one handle lock (with teeth facing outward) in  
gearcase notch. (Apply grease on smooth side of  
handle lock to aid in keeping lock in place until handle  
assembly is lowered into position.)  
HANDLE  
LOCK  
VIEWED FROM R.H. SIDE OF TILLER  
FLAT  
WASHER  
GEARCASE  
HANDLE ASSEMBLY  
HANDLE  
LOCK LEVER  
GEARCASE  
NOTCH  
SLOT  
HANDLE  
LOCK  
CARRIAGE  
BOLT  
PIVOT BOLT  
HANDLE  
BASE  
LOCKNUTS  
FIG. 3  
FIG. 5  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
ATTACH CLUTCH CABLE (See Fig. 6)  
CONNECT SHIFT ROD (See Fig. 7)  
Hook end of clutch cable through hole in control bar  
Insert end of shift rod into hole of shift lever indicator.  
Insert hairpin clip through hole of shift rod to secure.  
bracket if necessary.  
SHIFT  
HAIRPIN  
CLIP  
SHIFT  
ROD  
LEVER  
CONTROL BAR  
BRACKET  
END OF  
CLUTCH CABLE  
INDICATOR  
CONTROL BAR  
BRACKET  
CONTROL  
BAR  
FIG. 7  
REMOVE TILLER FROM CRATE  
Make sure shift lever indicator is in “N” position (See  
Fig. 7)  
Tilt tiller forward by lifting handle. Separate cardboard  
cover from leveling shield.  
Rotate tiller handle to the right and pull tiller out of  
carton.  
CLUTCH  
CABLE  
FIG. 6  
CHECK TIRE PRESSURE  
The tires on your unit were overinflated at the factory for  
shipping purposes. Correct and equal tire pressure is  
important for best tilling performance.  
Reduce tire pressure to 20 PSI (1.4 kg/cm2).  
HANDLE HEIGHT  
Handle height may be adjusted to better suit operator.  
(See “TO ADJUST HANDLE HEIGHT” in the Service  
and Adjustments section of this manual).  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
KNOWYOUR TILLER  
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATINGYOUR TILLER.  
Compare the illustrations with your tiller to familiarize yourself with the location of various controls and adjustments. Save  
this manual for future reference.  
These symbols may appear on your Tiller or in literature supplied with the product. Learn and understand their  
meaning.  
SHIFT LEVER  
THROTTLE CONTROL  
CHOKE CONTROL  
SHIFT LEVER  
INDICATOR  
DRIVE CONTROL  
BAR  
DEPTH STAKE  
LEVELING  
SHIELD  
RECOIL  
STARTER  
HANDLE  
OUTER SIDE  
SHIELD  
FIG. 8  
MEETS ANSI SAFETY REQUIREMENTS  
Our tillers conform to the safety standards of the American National Standards Institute.  
THROTTLE CONTROL - Used to control engine speed.  
SHIFT LEVER - Used to shift transmission gears.  
DRIVE CONTROL BAR - Used to engage tiller.  
DEPTH STAKE - Controls depth at which tiller will dig.  
LEVELING SHIELD - Levels tilled soil.  
OUTER SIDE SHIELD - Adjustable to protect small plants  
from being buried.  
SHIFT LEVER INDICATOR - Shows which gear the trans-  
mission is in.  
RECOIL STARTER HANDLE - Used to start the engine.  
CHOKE CONTROL - Used when starting a cold engine.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
The operation of any tiller can result in foreign objects thrown into the eyes, which can  
result in severe eye damage. Always wear safety glasses or eye shields before starting  
your tiller and while tilling. We recommend a wide vision safety mask over spectacles or  
standard safety glasses.  
HARD TO SHIFT GEARS  
HOW TO USEYOUR TILLER  
Know how to operate all controls before adding fuel and  
oil or attempting to start engine.  
Brieflyengagedrivecontrolbarandreleaseorrocktiller  
forward and backward until are able to shift gears.  
DEPTH STAKE (See Fig. 10)  
The depth stake can be raised or lowered to allow you more  
versatile tilling and cultivating, or to more easily transport  
your tiller.  
STOPPING (See Fig. 9)  
TINES AND DRIVE  
Release drive control bar to stop movement.  
Move shift lever to “N” (neutral) position.  
ENGINE  
Move throttle control to “STOP” position. If equipped  
with stop switch, move switch to “STOP” position.  
Never use choke to stop engine.  
TRANSPORT  
POSITION  
SHALLOWEST  
TILLING  
(CULTIVATING)  
HANDLE  
SHIFT LEVER  
DEEPEST  
TILLING  
THROTTLE  
CONTROL  
DEPTH  
STAKE  
DRIVE CONTROL  
BAR “ENGAGED”  
POSITION  
FIG. 10  
TILLING (See Fig. 11)  
Release depth stake pin. Pull the depth stake up for  
increased tilling depth. Place depth stake pin in hole  
of depth stake to lock in position.  
DRIVE CONTROL BAR  
“DISENGAGED” POSITION  
Place shift lever indicator in till position.  
Hold the drive control bar against the handle to start  
tilling movement. Tines and wheels will both turn.  
Move throttle control to “FAST” position for deep tilling.  
To cultivate, throttle control can be set at any desired  
speed, depending on how fast or slow you wish to  
cultivate.  
FIG. 9  
TINE OPERATION - WITH WHEEL DRIVE  
Always release drive control bar before moving shift  
lever into another position.  
IMPORTANT: ALWAYS RELEASE DRIVE CONTROL  
BAR BEFORE MOVING SHIFT LEVER INTO ANOTHER  
POSITION.  
Tine movement is achieved by moving shift lever to  
( ) till position and engaging drive control bar.  
DEPTH STAKE PIN  
“RELEASED” POSITION  
FORWARD- WHEELS ONLY/TINES  
STOPPED  
Releasedrivecontrolbarandmoveshiftleverindicator  
to “F” (forward) position. Engage drive control bar and  
tiller will move forward.  
REVERSE - WHEELS ONLY/TINES STOPPED  
DO NOT STAND DIRECTLY BEHIND TILLER.  
Release the drive control bar.  
Move throttle control to “SLOW” position.  
Move shift lever indicator to “R” (reverse) position.  
Hold drive control bar against the handle to start tiller  
movement.  
“LOCKED”  
POSITION  
NUT “B”  
OUTER  
SIDE SHIELD  
NUT “A”  
FIG. 11  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
Reinstall engine oil cap and tighten.  
TURNING  
For approximate capacity see “PRODUCT SPECIFIC-  
ATIONS” on page 3 of this manual. All oil must meet  
A.P.I. Service Classification SF-SJ.  
For cold weather operation you should change oil for  
easier starting (See oil viscosity chart in the Mainte-  
nance section of this manual).  
Release the drive control bar.  
Move throttle control to “SLOW” position.  
PlaceshiftleverindicatorinF(forward)position. Tines  
will not turn.  
Lift handle to raise tines out of ground.  
Swing the handle in the opposite direction you wish  
to turn, being careful to keep feet and legs away from  
tines.  
To change engine oil, see the Maintenance section in  
this manual.  
When you have completed your turn-around, release  
the drive control bar and lower handle. Place shift  
lever in till position and move throttle control to desired  
speed. To begin tilling, hold drive control bar against  
the handle.  
OIL FILL  
CAP/DIPSTICK  
OUTER SIDE SHIELDS (See Fig. 11)  
The back edges of the outer side shields are slotted so  
that the shields can be raised for deep tilling and lowered  
for shallow tilling to protect small plants from being buried.  
Loosen nut “A” in slot and nut “B”. Move shield to desired  
position (both sides). Retighten nuts.  
FIG. 12  
TO TRANSPORT  
ADD GASOLINE  
Fill fuel tank to bottom of filler neck. Do not overfill.  
Use fresh, clean, regular unleaded gasoline with a  
minimum of 87 octane. (Use of leaded gasoline will  
increase carbon and lead oxide deposits and reduce  
valve life). Do not mix oil with gasoline. Purchase fuel  
in quantities that can be used within 30 days to assure  
fuel freshness.  
CAUTION: Beforeliftingortransporting,  
allow tiller engine and muffler to cool.  
Disconnect spark plug wire. Drain  
gasoline from fuel tank.  
AROUND THEYARD  
Release the depth stake pin. Move the depth stake  
down to the top hole for transporting the tiller. Place  
depth stake pin in hole of depth stake to lock in posi-  
tion. This prevents tines from scuffing the ground.  
CAUTION: Fill to within 1/2 inch of top  
offueltanktopreventspillsandtoallow  
for fuel expansion. If gasoline is ac-  
cidentally spilled, move machine away  
from area of spill. Avoid creating any  
sourceofignitionuntilgasolinevapors  
have disappeared.  
Wipe off any spilled oil or fuel. Do not  
store, spill or use gasoline near an  
open flame.  
Place shift lever indicator in “F” (forward) position for  
transporting.  
Hold the drive control bar against the handle to start  
tiller movement. Tines will not turn.  
Move throttle control to desired speed.  
AROUND TOWN  
Disconnect spark plug wire.  
Drain fuel tank.  
Transport in upright position to prevent oil leakage.  
IMPORTANT: WHEN OPERATING IN TEMPERATURES  
BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE  
GASOLINE TO HELP INSURE GOOD COLD WEATHER  
STARTING.  
BEFORE STARTING ENGINE  
IMPORTANT: BE VERY CAREFUL NOT TO ALLOW DIRT  
TO ENTER THE ENGINE WHEN CHECKING OR ADDING  
OIL OR FUEL. USE CLEAN OIL AND FUEL AND STORE IN  
APPROVED, CLEAN, COVERED CONTAINERS. USE CLEAN  
FILL FUNNELS.  
CAUTION: Alcohol blended fuels (called  
gasohol or using ethanol or methanol) can at-  
tract moisture which leads to separation and  
formation of acids during storage. Acidic gas  
can damage the fuel system of an engine while  
in storage. To avoid engine problems, the fuel  
system should be emptied before storage of  
30 days or longer. Drain the gas tank, start  
the engine and let it run until the fuel lines  
and carburetor are empty. Use fresh fuel next  
season. SeeStorageInstructionsforadditional  
information. Never use engine or carburetor  
cleaner products in the fuel tank or permanent  
damage may occur.  
CHECK ENGINE OIL LEVEL (See Fig. 12)  
The engine in your unit has been shipped, from the  
factory, already filled with SAE 30 summer weight oil.  
Be sure tiller is level and the area around oil fill is  
clean.  
Check oil level before each use. Add oil if needed. Fill  
to full line on dipstick.  
To read proper level, tighten engine oil cap each  
time.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
TO START ENGINE (See Fig. 13)  
TILLING HINTS  
CAUTION: Keep drive control bar in  
“DISENGAGED” position when start-  
ing engine.  
CAUTION: Untilyouareaccustomedto  
handlingyourtiller,startactualelduse  
with throttle in slow position (mid-way  
between “FAST” and “IDLE”).  
When starting engine for the first time or if engine has run  
out of fuel, it will take extra pulls of the recoil starter to  
move fuel from the tank to the engine.  
Tilling is digging into, turning over, and breaking up  
packedsoilbeforeplanting.Loose,unpackedsoilhelps  
root growth. Best tilling depth is 4" to 6" (10-15 cm).  
A tiller will also clear the soil of unwanted vegetation.  
The decomposition of this vegetable matter enriches  
the soil. Depending on the climate (rainfall and wind),  
it may be advisable to till the soil at the end of the  
growing season to further condition the soil.  
Soilconditionsareimportantforpropertilling.Tineswill  
notreadilypenetratedry,hardsoilwhichmaycontribute  
to excessive bounce and difficult handling of your tiller.  
Hard soil should be moistened before tilling; however,  
extremely wet soil will “ball-up” or clump during tilling.  
Wait until the soil is less wet in order to achieve the  
best results. When tilling in the fall, remove vines and  
long grass to prevent them from wrapping around the  
tine shaft and slowing your tilling operation.  
You will find tilling much easier if you leave a row un-  
tilled between passes. Then go back between tilled  
rows. (See Fig. 14) There are two reasons for doing  
this.First, wide turns are much easier to negotiate than  
about-faces. Second, the tiller won’t be pulling itself,  
and you, toward the row next to it.  
Donotleanonhandle. Thistakesweightoffthewheels  
and reduces traction. To get through a really tough  
section of sod or hard ground, apply upward pressure  
on handle or lower the depth stake.  
Make sure spark plug wire is properly connected.  
Move shift lever indicator to “N” (neutral) position.  
Place throttle control in “FAST” position.  
To start a cold engine, push primer five (5) times before  
trying to start. Use a firm push. This step is not usually  
necessary when starting an engine which has already  
run for a few minutes.  
Grasp recoil starter handle with one hand and grasp  
tiller handle with other hand. Pull rope out slowly until  
engine reaches start of compression cycle (rope will  
pull slightly harder at this point).  
Pull recoil starter handle quickly. Do not let starter  
handle snap back against starter.  
Allow engine to warm up for a few minutes before  
engaging tines.  
NOTE: In cooler weather it may be necessary to repeat  
priming steps. In warmer weather over priming may  
cause flooding and engine will not start. If you do flood  
engine, wait a few minutes before attempting to start and  
do not repeat priming steps.  
RECOIL STARTER  
PRIMER  
HANDLE  
4
3
2
1
FIG. 13  
5
6
7
FIG. 14  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
TINE SHEAR PINS  
The tine assemblies on your tiller are secured to the tine  
shaft with shear pins (See “TINE REPLACEMENT” in the  
Service and Adjustments section of this manual).  
ADJUST WHEELS FOR CULTIVATING  
(See Figs. 16 and 17)  
Place blocks under right hand side of tiller and remove  
hairpin clip and clevis pin from right hand wheel.  
Move wheel outward approximately 1 inch (2.5 cm)  
until hole in inner wheel hub lines up with inner hole  
in axle.  
If the tiller is unusually overloaded or jammed, the shear  
pins are designed to break before internal damage occurs  
to the transmission.  
Replace clevis pin and hairpin clip on inside of wheel  
and remove blocks.  
Repeat preceding steps on left hand side.  
If shear pin(s) break, replace only with those shown in  
the Repair Parts section of this manual.  
CULTIVATING  
NOTE: In extremely rough conditions and while cultivat-  
ing, the wheels should be moved outward on the axle for  
increased stability.  
Cultivating is destroying the weeds between rows to pre-  
vent them from robbing nourishment and moisture from the  
plants. At the same time, breaking up the upper layer of  
soil crust will help retain moisture in the soil. Best digging  
depth is 1" to 3" (2.5-7.5 cm). Lower the outer side shields  
to protect small plants from being buried.  
OUTER VIEW OF TIRE  
Cultivate up and down the rows at a speed which will  
allow tines to uproot weeds and leave the ground in  
rough condition, promoting no further growth of weeds  
and grass (See Fig. 15).  
CLEVIS  
PIN  
HAIRPIN  
CLIP  
FIG. 16  
FIG. 15  
INNER VIEW OF TIRE  
CLEVIS  
PIN  
HAIRPIN  
CLIP  
FIG. 17  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
MAINTENANCE  
SCHEDULE  
FILL IN DATES  
AS YOU COMPLETE  
REGULAR SERVICE  
SERVICE DATES  
EVERY SEASON  
BEFORE EEAVCEHRUYS5EHEOVEURYS 25EHVOEURRYS50 HOURS  
Check Engine Oil Level  
Change Engine Oil  
1,2  
Oil Pivot Points  
Inspect Spark Arrester / Muffler  
Inspect Air Screen  
Clean or Replace Air Cleaner Cartridge  
Clean Engine Cylinder Fins  
Replace Spark Plug  
2
RH Gear Case Grease Fitting (1oz.)  
1 - Change more often when operating under a heavy load or in high ambient temperatures.  
2 - Service more often when operating in dirty or dusty conditions.  
LUBRICATION CHART  
GENERAL RECOMMENDATIONS  
The warranty on this tiller does not cover items that have  
beensubjectedtooperatorabuseornegligence. Toreceive  
fullvaluefromthewarranty,theoperatormustmaintaintiller  
cTHROTTLE CONTROL  
as instructed in this manual.  
d ENGINE  
Some adjustments will need to be made periodically to  
properly maintain your tiller.  
eRH GEAR CASE  
GREASE FITTING  
All adjustments in the Service and Adjustments section  
of this manual should be checked at least once each  
season.  
c DEPTH  
STAKE PIN  
Once a year you should replace the spark plug, clean  
or replace air filter, and check tines and belts for wear.  
A new spark plug and clean air filter assure proper  
air-fuel mixture and help your engine run better and  
last longer.  
c LEVELING  
SHIELD  
HINGES  
c IDLER  
BEFORE EACH USE  
c WHEEL  
BRACKET  
HUB  
Check engine oil level.  
Check tine operation.  
Check for loose fasteners.  
cSAE 30 OR 10W-30 MOTOR OIL  
dREFER TO MAINTENANCE “ENGINE” SECTION  
eEP #1 GREASE  
LUBRICATION  
Keep unit well lubricated (See “LUBRICATION CHART”).  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
Disconnect spark plug wire before performing any maintenance (except carburetor adjustment) to prevent  
accidental starting of engine.  
Prevent fires! Keep the engine free of grass, leaves, spilled oil, or fuel. Remove fuel from tank before tipping  
unit for maintenance. Clean muffler area of all grass, dirt, and debris.  
Do not touch hot muffler or cylinder fins as contact may cause burns.  
ENGINE  
LUBRICATION  
Use only high quality detergent oil rated with API service  
classification SF-SJ. Select the oil’s SAE viscosity grade  
according to your expected temperature.  
OIL  
DRAIN  
PLUG  
SAE VISCOSITY GRADES  
SAE 30  
OIL LEVEL  
5W-30  
OIL FILLER  
PLUG  
-20  
0
30  
32 40  
0
100  
60  
80  
F
C
-20  
10  
-30  
-10  
20  
30  
40  
FIG. 19  
TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE  
oil_visc_chart1_e  
FIG. 18  
AIR FILTER (See Fig. 20)  
Yourenginewillnotrunproperlyusingadirtyairlter. Clean  
the foam pre-cleaner after every 25 hours of operation or  
every season. Service paper cartridge every 100 hours of  
operation or every season, whichever occurs first.  
NOTE: Although multi-viscosity oils (5W-30, 10W-30, etc.)  
improve starting in cold weather, these multi-viscosity oils  
will result in increased oil consumption when used above  
32°F (0°C). Check your engine oil level more frequently to  
avoid possible engine damage from running low on oil.  
Service air cleaner more often under dusty conditions.  
Remove cover screw and cover.  
TO SERVICE PRE-CLEANER  
Change the oil after every 25 hours of operation or at  
least once a year if the tiller is not used for 25 hours in  
one year.  
Remove foam pre-cleaner from air cleaner cover.  
Wash it in liquid detergent and water.  
Squeeze it dry in a clean cloth.  
Saturate it in engine oil. Wrap it in clean, absorbent  
cloth and squeeze to remove excess oil.  
If very dirty or damaged, replace pre-cleaner.  
Reinstall pre-cleaner into air cleaner cover.  
Reinstall cover and secure screw.  
Check the crankcase oil level before starting the engine  
and after each five (5) hours of continuous use. Add SAE  
30 motor oil or equivalent. Tighten oil filler plug securely  
each time you check the oil level.  
TO CHANGE ENGINE OIL (See Figs. 18 and 19)  
Determine temperature range expected before oil change.  
All oil must meet API service classification SF-SJ.  
TO SERVICE CARTRIDGE  
Carefully remove cartridge to prevent debris from  
entering carburetor. Clean base carefully to prevent  
debris from entering carburetor.  
Be sure tiller is on level surface.  
Oil will drain more freely when warm.  
Use a funnel to prevent oil spill on tiller, and catch oil  
in a suitable container.  
Clean cartridge by tapping gently on flat surface. If  
very dirty or damaged, replace cartridge.  
Reinstall cartridge, cover with pre-cleaner and secure  
with screw.  
Remove drain plug.  
Tip tiller forward to drain oil.  
After oil has drained completely, replace oil drain plug  
and tighten securely.  
IMPORTANT: PETROLEUMSOLVENTS,SUCHASKEROSENE,  
ARE NOT TO BE USED TO CLEAN THE CARTRIDGE. THEY  
MAY CAUSE DETERIORATION OFTHE CARTRIDGE. DO NOT  
OILCARTRIDGE. DONOTUSEPRESSURIZEDAIRTOCLEAN  
OR DRY CARTRIDGE.  
Remove oil filler plug. Be careful not to allow dirt to  
enter the engine.  
Refillenginewithoil.SeeCHECKENGINEOILLEVEL”  
in the Operation section of this manual.  
FOAM  
PRECLEANER  
BASE  
COVER  
COVER  
SCREW  
AIR CLEANER  
CARTRIDGE  
FIG. 20  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
COOLING SYSTEM (See Fig. 21)  
Your engine is air cooled. For proper engine performance  
and long life keep your engine clean.  
MUFFLER  
Do not operate tiller without muffler. Do not tamper with  
exhaustsystem.Damagedmufflersorsparkarresterscould  
create a fire hazard. Inspect periodically and replace if  
necessary. If your engine is equipped with a spark arrester  
screen assembly, remove every 50 hours for cleaning and  
inspection. Replace if damaged.  
Clean air screen frequently using a stiff-bristled  
brush.  
Remove blower housing and clean as necessary.  
Keep cylinder fins free of dirt and chaff.  
SPARK PLUG  
CYLINDER FINS  
Replace spark plugs at the beginning of each tilling sea-  
son or after every 50 hours of use, whichever comes first.  
Spark plug type and gap setting is shown in “PRODUCT  
SPECIFICATIONS” on page 3 of this manual.  
BLOWER  
HOUSING  
TRANSMISSION  
Once a season, lubricate the right hand side gear case  
grease fitting with oz. of EP #1 grease.  
MUFFLER  
AIR SCREEN  
CLEANING  
Do not clean your tiller when the engine and transmission  
are hot. We do not recommend using pressurized water  
(garden hose, etc.) to clean your unit unless the gasket  
area around the transmission and the engine muffler, air  
fi lter and carburetor are covered to keep water out. Water  
in engine will shorten the useful life of your tiller.  
FIG. 21  
Clean engine, wheels, finish, etc. of all foreign mat-  
ter.  
Keep finished surfaces and wheels free of all gasoline,  
oil, etc.  
Protect painted surfaces with automotive type wax.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come into  
contact with plug.  
TILLER  
TIRE CARE  
TO ADJUST HANDLE HEIGHT (See Fig. 22)  
Select handle height best suited for your tilling conditions.  
Handle height will be different when tiller digs into soil.  
CAUTION: When mounting tires, un-  
lessbeadsareseated,overinflationcan  
cause an explosion.  
First loosen handle lock lever.  
Handle can be positioned at different settings between  
“HIGH” and “LOW” positions.  
Maintain 20 PSI (1.4 kg/cm2) of tire pressure. If tire  
pressures are not equal, tiller will pull to one side.  
Keep tires free of gasoline or oil which can damage  
rubber.  
Retighten handle lock lever securely after adjusting.  
TO REMOVE WHEEL (See Fig. 23)  
HANDLE (HIGH  
POSITION)  
Place blocks under transmission to keep tiller from  
tipping.  
Remove hairpin clip and clevis pin from wheel.  
Remove wheel and tire.  
Repair tire and reassemble.  
HANDLE LOCK  
LEVER  
CLEVIS PIN  
HANDLE (LOW  
POSITION)  
FIG. 22  
HAIRPIN CLIP  
FIG. 23  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
To maintain the superb tilling performance of this  
machine the tines should be checked for sharpness,  
wear, and bending, particularly the tines which are  
next to the transmission. If the gap between the tines  
exceeds 3-1/2 inches (9 cm), they should be replaced  
or straightened as necessary.  
New tines should be assembled as shown in Fig.  
28. Sharpened tine edges will rotate rearward from  
above.  
TINE REPLACEMENT  
(See Figs. 24, 25 and 26)  
CAUTION: Tines are sharp. Wear  
gloves or other protection when han-  
dling tines.  
A badly worn tine causes your tiller to work harder and dig  
more shallow. Most important, worn tines cannot chop and  
shred organic matter as effectively nor bury it as deeply as  
good tines. A tine this worn needs to be replaced.  
NEW TINE  
WORN TINE  
TINE  
TINE  
3-1/2" MAX (9 CM)  
FIG. 24  
FIG. 25  
COUNTER  
TINE  
ROTATION  
HAIRPIN CLIP  
SHARP EDGE  
SHARP EDGE  
SHARP EDGE  
SHARP EDGE  
SHARP  
EDGES  
SHEAR PIN  
SHARP EDGE  
FIG. 26  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
TO REMOVE BELT GUARD  
TO REPLACE GROUND DRIVE BELT  
(See Fig. 27)  
(See Figs. 27 and 28)  
RemovebeltguardasdescribedinTOREMOVEBELT  
GUARD”.  
Remove old belt by slipping off engine pulley first then  
remove from transmission pulley.  
Place new belt in groove of transmission pulley and  
into engine pulley. BELT MUST BE IN GROOVE ON  
TOP OF IDLER PULLEY. NOTE POSITION OF BELT  
TO GUIDES.  
NOTE: For ease of removal, remove hairpin clip and clevis  
pin from left wheel. Pull wheel out from tiller about 1 inch  
(2.5 cm).  
Remove two (2) screws from side of belt guard.  
Remove hex nut and washer from bottom of belt guard  
(located behind wheel).  
Pull belt guard out and away from unit.  
Replace belt guard by reversing above procedure.  
Check belt adjustment as described below.  
Replace belt guard.  
Reposition wheel and replace clevis pin and hairpin  
clip.  
BELT GUARD  
SCREW  
HEX NUT  
AND WASHER  
(LOCATED BEHIND  
TIRE)  
GROUND DRIVE BELT ADJUSTMENT (See  
Fig. 28)  
For proper belt tension, the extension spring should have  
about 5/8 inch (16 mm) stretch when drive control bar is  
in “ENGAGED” position. This tension can be attained as  
follows:  
Loosen cable clip screw securing the drive control  
cable.  
SCREW  
HAIRPIN CLIP AND  
Slide cable forward for less tension and rearward for  
more tension until about 5/8 inch (16 mm) stretch is  
obtained while the drive control bar is engaged.  
CLEVIS PIN  
FIG. 27  
Tighten cable clip screw securely.  
CABLE CLIP  
SCREW  
ENGINE  
PULLEY  
DRIVE  
CONTROL  
CABLE  
LESS  
TENSION  
MORE  
TENSION  
5/8"  
IDLER  
PULLEY  
EXTENSION  
SPRING  
TRANSMISSION  
PULLEY  
FIG. 28  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
ENGINE  
TO ADJUST THROTTLE CONTROL CABLE  
(See Fig. 29)  
The throttle control has been preset at the factory and  
adjustment should not be necessary. If adjustment is  
necessary, proceed as follows:  
HIGH SPEED STOP  
THROTTLE  
CABLE  
With engine not running, move remote throttle control  
lever to “FAST” position.  
If throttle lever on engine touches high speed stop, no  
further adjustment is necessary. If throttle lever does  
not touch high speed stop, continue with adjustment  
procedure.  
THROTTLE  
LEVER  
CABLE  
CLAMP  
SCREW  
Loosen cable clamp screw.  
Move throttle lever up until it touches high speed stop,  
and hold in this position.  
FIG. 29  
Tighten cable clamp screw securely.  
TO ADJUST CARBURETOR  
Thecarburetorhasbeenpresetatthefactoryandadjustment  
should not be necessary. However, engine performance  
can be affected by differences in fuel, temperature, altitude  
or load. If the carburetor does need adjustment, contact  
your nearest authorized service center/department  
IMPORTANT: NEVERTAMPERWITHTHEENGINEGOVERNOR,  
WHICH IS FACTORY SET FOR PROPER ENGINE SPEED.  
OVERSPEEDING THE ENGINE ABOVE THE FACTORY HIGH  
SPEED SETTING CAN BE DANGEROUS. IF YOU THINK THE  
ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING,  
CONTACTYOURNEARESTAUTHORIZEDSERVICECENTER/  
DEPARTMENT, WHICH HAS THE PROPER EQUIPMENT AND  
EXPERIENCE TO MAKE ANY NECESSARY ADJUSTMENTS.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STORAGE  
Immediately prepare your tiller for storage at the end of the  
ENGINE OIL  
Drainoil(withenginewarm)andreplacewithcleanoil. (See  
“ENGINE” in the Maintenance section of this manual).  
season or if the unit will not be used for 30 days or more.  
WARNING: Never store the tiller with  
gasoline in the tank inside a building  
where fumes may reach an open flame  
orspark. Allowtheenginetocoolbefore  
storing in any enclosure.  
CYLINDER(S)  
Remove spark plug.  
Pour 1 ounce (29 ml) of oil through spark plug hole into  
cylinder.  
Pull starter handle slowly several times to distribute  
oil.  
Replace with new spark plug.  
TILLER  
Cleanentiretiller(SeeCLEANINGintheMaintenance  
section of this manual).  
Inspect and replace belts, if necessary (See belt re-  
placement instructions in the Service and Adjustments  
section of this manual).  
Lubricate as shown in the Maintenance section of this  
manual.  
Be sure that all nuts, bolts and screws are securely  
fastened. Inspect moving parts for damage, breakage  
and wear. Replace if necessary.  
Touch up all rusted or chipped paint surfaces; sand  
lightly before painting.  
OTHER  
Do not store gasoline from one season to an-  
other.  
Replace your gasoline can if your can starts to rust.  
Rust and/or dirt in your gasoline will cause problems.  
If possible, store your unit indoors and cover it to give  
protection from dust and dirt.  
Cover your unit with a suitable protective cover that  
does not retain moisture. Do not use plastic. Plastic  
cannot breathe which allows condensation to form and  
will cause your unit to rust.  
IMPORTANT: NEVER COVER TILLER WHILE ENGINE AND  
EXHAUST AREAS ARE STILL WARM.  
ENGINE  
FUEL SYSTEM  
IMPORTANT:  
IT IS IMPORTANT TO PREVENT GUM  
DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM  
PARTS SUCH AS THE CARBURETOR, FUEL FILTER, FUEL  
HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE  
INDICATES THAT ALCOHOL BLENDED FUELS (CALLED  
GASOHOL OR USING ETHANOL OR METHANOL) CAN  
ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND  
FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS  
CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN  
STORAGE.  
Drain the fuel tank.  
Start the engine and let it run until the fuel lines and  
carburetor are empty.  
Never use engine or carburetor cleaner products in the  
fuel tank or permanent damage may occur.  
Use fresh fuel next season.  
NOTE: Fuel stabilizer is an acceptable alternative in mini-  
mizing the formation of fuel gum deposits during storage.  
Add stabilizer to gasoline in fuel tank or storage container.  
Always follow the mix ratio found on stabilizer container.  
Run engine at least 10 minutes after adding stabilizer to  
allow the stabilizer to reach the carburetor. Do not drain  
the gas tank and carburetor if using fuel stabilizer.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING POINTS  
PROBLEM  
CAUSE  
CORRECTION  
Will not start  
1. Out of fuel.  
1. Fill fuel tank.  
2. Engine not “CHOKED” properly.  
3. Engine flooded.  
4. Dirty air cleaner.  
5. Water in fuel.  
2. See “TO START ENGINE” in Operation section.  
3. Wait several minutes before attempting to start.  
4. Clean or replace air cleaner cartridge.  
5. Drain fuel tank and carburetor, and refill tank with  
fresh gasoline.  
6. Clogged fuel tank.  
7. Loose spark plug wire.  
6. Remove fuel tank and clean.  
7. Make sure spark plug wire is seated properly on  
plug.  
8. Bad spark plug or improper gap.  
9. Carburetor out of adjustment.  
8. Replace spark plug or adjust gap.  
9. Make necessary adjustments.  
Hard to start  
1. Throttle control not set properly.  
2. Dirty air cleaner.  
3. Bad spark plug or improper gap.  
4. Stale or dirty fuel.  
1. Place throttle control in “FAST” position.  
2. Clean or replace air cleaner cartridge.  
3. Replace spark plug or adjust gap.  
4. Drain fuel tank and refill with fresh gasoline.  
5. Make sure spark plug wire is seated properly on  
plug.  
5. Loose spark plug wire.  
6. Carburetor out of adjustment.  
6. Make necessary adjustments.  
Loss of power  
1. Engine is overloaded.  
2. Dirty air cleaner.  
3. Low oil level/dirty oil.  
4. Faulty spark plug.  
5. Oil in fuel.  
1. Set depth stake for shallower tilling.  
2. Clean or replace air cleaner cartridge.  
3. Check oil level/change oil.  
4. Clean and regap or change spark plug.  
5. Drain and clean fuel tank and refill, and clean  
carburetor.  
6. Stale or dirty fuel.  
7. Water in fuel.  
6. Drain fuel tank and refill with fresh gasoline.  
7. Drain fuel tank and carburetor, and refill tank with  
fresh gasoline.  
8. Clogged fuel tank.  
8. Remove fuel tank and clean.  
9. Spark plug wire loose.  
10. Dirty engine air screen.  
11. Dirty/clogged muffler.  
12. Carburetor out of adjustment.  
13. Poor compression.  
9. Connect and tighten spark plug wire.  
10. Clean engine air screen.  
11. Clean/replace muffler.  
12. Make necessary adjustments.  
13. Contact an authorized service center/department.  
Engine overheats  
1. Low oil level/dirty oil.  
2. Dirty engine air screen.  
3. Dirty engine.  
4. Partially plugged muffler.  
5. Improper carburetor adjustment.  
1. Check oil level/change oil.  
2. Clean engine air screen.  
3. Clean cylinder fins, air screen, and muffler area.  
4. Remove and clean muffler.  
5. Adjust carburetor to richer position.  
Excessive bounce/  
difficult handling  
1. Ground too dry and hard.  
1. Ground too wet.  
1. Moisten ground or wait for more favorable soil  
conditions.  
Soil balls up or clumps  
1. Wait for more favorable soil conditions.  
Engine runs but tiller  
won’t move  
1. Drive control bar is not engaged.  
2. V-belt not correctly adjusted.  
3. V-belt is off pulley(s).  
1. Engage drive control.  
2. Inspect/adjust V-belt.  
3. Inspect V-belt.  
Engine runs but labors  
when tilling  
1. Tilling too deep.  
2. Throttle control not properly adjusted.  
3. Carburetor out of adjustment.  
1. Set depth stake for shallower tilling.  
2. Check throttle control setting.  
3. Make necessary adjustments.  
Tines will not rotate  
1. Shear pin(s) broken.  
1. Gears not timed.  
1. Replace shear pin(s).  
Hard to shift into gear  
1. Briefly engage drive control bar and release or rock  
tiller forward and backward until are able to shift  
gears.  
Tiller shuts off when  
drive control bar  
engaged  
1. Shift lever set in between counter rotating till  
position and forward rotating till position.  
2. Tines jammed.  
1. Shift to either counter rotating till position or forward  
rotating till position.  
2. Clear tines.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TILLER - - MODEL NUMBER WET6500A  
HANDLE ASSEMBLY  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
1
175769  
Control, Throttle  
Grip, Handle  
26  
29  
31  
34  
35  
36  
37  
39  
38  
41  
42  
159232  
Cable, Clutch  
Nut, Keps #10-24 Unc  
Bolt, Pivot  
Bracket, Clutch Cable  
Grommet, Handle  
2
150744  
73731000  
150696  
145821  
146480  
4
8
159227  
Bar, Control  
71191008  
8389J  
Screw, Pan Hd. #10-24  
Grip, Handle  
Clip, Hairpin  
Rod, Shift  
Bolt, Carriage 3/8-16 x 1 Gr. 5  
Lock, Handle  
Nut Crownlock 3/8-16 Unc  
Washer 13/32 x 1 x 11 Ga.  
Lever, Lock, Handle  
Handle  
10  
11  
15  
16  
17  
18  
19  
20  
21  
4497H  
180456X550 Bracket, Handle  
108281X  
72110608  
109229X  
73680600  
19131611  
109228X  
150217  
102604X  
10040500  
73800500  
72110514  
121248X  
Grip, Bar Control  
Washer, Lock 5/16  
Locknut 5/16-18  
Bolt, Carriage 5/16-18 x 1-3/4  
Bushing, Snap  
NOTE: All component dimensions given in U.S. inches.  
1 inch = 25.4 mm  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TILLER - - MODEL NUMBER WET6500A  
MAINFRAME, LEFT SIDE  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
44  
65  
126875X  
4497H  
Rivet, Drilled  
Clip, Hairpin  
1
2
3
4
5
6
7
8
9
73510500  
Nut, Keps 5/16-18  
10040600  
73220600  
170127  
Washer, Lock 3/8  
165501X550 Guard, Belt  
Nut, Hex 3/8-16  
132801  
Belt, V  
Shield, Inner, Belt Guard  
Pin Spirol Flared  
104679X  
12000032  
159229  
Pulley, Idler  
164329  
Ring, Klip  
110111X  
72110404  
8700J  
Lever, Shift  
Bracket, Idler  
Bolt, Carriage 1/4-20 x 1/2 Gr. 5  
Plate, Shift Indicator  
Screw, Hex, Washer Head, Slotted  
#10-24 x 1/2  
102384X  
102141X  
74760616  
102383X  
74760524  
102331X  
130812  
74760544  
140062  
170488  
Bolt, Hex 5/16-16 x 12  
Shaft, Idler Arm  
86777  
Bolt, Hex 3/8-16 x 1  
Counterweight, L. H.  
Bolt, Hex 5/16-18 x 1-1/2  
Bracket, Reinforcement, L. H.  
Sheave, Engine  
Bolt, Hex 5/16-18 x 2-3/4  
Cap, Plunger  
Screw, Hex Wsh Slt #10-24 x .50  
Nut, Lock 5/16-18  
Nut, Lock Hex Flange  
10  
11  
12  
13  
14  
15  
16  
19  
21  
22  
23  
9484R  
Clip  
10040400  
73220400  
23230506  
156117  
Washer, Lock 1/4  
Nut, Hex 1/4-20  
Screw, Set, Hex 5/16-18 x 3/8  
Spacer, Split 0.327 x 0.42 x 1.220  
Washer 11/32 x 11/16 x 16 Ga.  
Sheave, Transmission  
Ring, Retainer  
19111116  
145102  
12000028  
110652X  
74770508  
102190X  
73800500  
73970500  
Spacer, Split 0.327 x 0.42 x 2.09  
Bolt Hex 5/16-24 x 1/2  
Tire  
NOTE: All component dimensions given in U.S. inches.  
183122X624 Rim  
795R Tire Valve  
1 inch = 25.4 mm  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TILLER - - MODEL NUMBER WET6500A  
MAINFRAME, RIGHT SIDE  
15  
14  
13  
12  
5
10  
7
8
9
11  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
5
102332X  
Bracket, Reinforcement  
Counter Weight, R.H.  
Washer, Lock 3/8  
Nut, Hex 3/8-16  
Bolt, Hex 5/16-18 x 1-1/2  
Clip, Hairpin  
Rivet, Drilled  
13  
102190X  
Tire  
7
102173X  
10040600  
73220600  
74760524  
4497H  
183122X624 Rim  
8
9
10  
11  
12  
795R  
73970500  
- - - - - - -  
Tire Valve  
Nut, Hex Flange  
Engine, Tec Model No. OHH65  
(Order parts from engine Manufac-  
turer)  
14  
15  
126875X  
NOTE: All component dimensions given in U.S. inches.  
1 inch = 25.4 mm  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TILLER - - MODEL NUMBER WET6500A  
TRANSMISSION  
12  
13  
9
15  
11  
60  
10  
16  
48  
9
14  
25  
24  
8
5
18  
31  
7
23  
44  
6
22  
18  
21  
30  
5
18  
29  
19  
4
18  
18  
43  
34  
39  
42  
40  
41  
20  
28  
33  
53  
32  
27  
49  
38  
37  
3
37  
2
35  
36  
50  
24  
25  
52  
53  
44  
58  
51  
transmission_1.95b  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
1
180677  
Transmission Assembly (Includes  
Key Nos. 2-53)  
Gearcase, L.H. w/Bearing (Includes  
Key No. 4)  
29  
30  
31  
32  
33  
34  
35  
36  
102134X  
150737  
143008  
106388X  
102121X  
102112X  
102101X  
154355  
Chain #35-50 Pitch  
Ground Shaft Assembly  
Bearing, Shaft, Ground Drive  
Spacer 0.70 x 1.00 x 1.150  
Sprocket and Gear Assembly  
Shaft, Reduction (2nd)  
Screw, Whiz, Lock 5/16-18 x 3-1/2  
Sprocket Assembly w/Bearing (In-  
cludes Key Nos. 37 and 38)  
Bearing, Needle  
2
180627  
3
161963  
5020J  
1370H  
137335  
145101  
4895H  
154467  
7392M  
100371K  
106160X  
142145  
8353J  
12000039  
154466  
4358J  
Gasket, Gearcase  
Bearing, Needle  
Washer, Thrust 5/8 x 1.10 x 1/32  
Pinion, Input  
4
5
6
7
Shaft, Input  
8
Bearing, Needle  
Washer, Seal  
37  
38  
39  
40  
41  
42  
43  
44  
48  
4422J  
9
154356  
105345X  
105346X  
8358J  
Sprocket, Tine  
Gear, Cluster, Red 1st & 2nd  
Gear, Reverse  
Shaft, Reduction (1st)  
Washer, Thrust  
Spacer 1.01 x 1.75 x 0.760  
Seal Asm, Oil  
Gearcase, R.H. w/Bearing (In-  
cludes Key No. 8)  
Shaft, Tine  
Chain, Roller #50-50 Pitch  
Screw 1/4-20 x 1/2  
Nut, Hex 5/16-18  
10  
11  
12  
13  
14  
15  
16  
18  
19  
20  
Ball, Steel  
Spring, Shift, Fork  
O-Ring  
Arm,. Shift  
4220R  
Fork, Shift  
106146X  
155236  
180631  
Ring, Klip  
Shaft, Shift  
Washer  
12000040  
102114X  
Ring, Klip  
49  
50  
51  
52  
53  
58  
60  
- -  
132688  
106147X  
17720408  
73220500  
165140  
179520  
6855M  
Gear, Assembly, Reverse Idler (In-  
cludes Key Nos. 21 and 22)  
Gear, Reverse Idler  
Bearing, Needle  
Shaft, Reverse Idler  
Washer, Lock 7/16  
Nut, Hex 7/16-20  
Bearing, Shaft, Ground Drive  
Spacer 0.765 x 1.125 x 1.23  
21  
22  
23  
24  
25  
27  
28  
102115X  
6803J  
Kit, Bearing, Tine Shaft  
Bolt Shoulder 1/4-20 Unc x .875  
Fitting Grease  
102111X  
10040700  
73610700  
143009  
6066J  
Grease, Plastilube #1  
NOTE: All component dimensions given in U.S. inches.  
106390X  
1 inch = 25.4 mm  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TILLER - - MODEL NUMBER WET6500A  
TINE SHIELD  
4
5
3
6
7
1
8
14  
13  
2
29  
5
14  
12  
11  
9
18  
10  
12  
28  
11  
12  
12  
11  
23  
11  
24  
23  
33  
25  
32  
16  
5
12  
1
23  
11  
19  
27  
24  
22  
21  
26  
29  
20  
15  
16  
tine_shield_13_in(sears)  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
Nut, Flange 5/16-18  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
32  
33  
72040410  
102701X  
73220600  
102156X  
74930632  
4440J  
72140404  
6712J  
109227X  
Bolt, Carriage 1/4-20 x 1-1/4 Gr. 5  
Grip  
Nut, Hex 3/8-16  
Stake, Depth  
Bolt, Hex 3/8-16 x 2  
Hinge  
Bolt, Carriage 1/4-20 x 1/2 Gr. 5  
Cap, Vinyl  
Pad, Idler  
1
73900500  
2
161415X550 Shield, Side, Outer L. H.  
3
8393J  
Pin, Stake, Depth  
Ring, Klip  
Bolt, Carriage 5/16-18 x 3/4  
Spring  
Bracket, Latch  
Spring, Depth Stake  
4
12000035  
180847  
8394J  
5
6
7
8392J  
109230X  
102326X550 Shield, Tine  
8
9
102695X550 Shield, Leveling  
10  
11  
12  
13  
14  
15  
16  
72140508  
73220500  
10040500  
72110510  
124343X  
Bolt 5/16-18 x 1  
120588X  
Pin, Hinge  
Nut, Hex 5/16-18  
104085X550 Shield, Side  
Washer, Lock 5/16  
73220400  
10040400  
Nut Fin Hex 1/4-20 Unc  
Washer Lock Hvy Helical 1/4  
Bolt, Carriage 5/16-18 x 1-1/4  
Bracket, Shield Tine  
161414X550 Shield, Side, Outer R.H.  
73900400 Nut, Hex Flange 1/4-20 Unc  
NOTE: All component dimensions given in U.S. inches.  
1 inch = 25.4 mm  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TILLER - - MODEL NUMBER WET6500A  
TINE ASSEMBLY  
2
1
1
1
3
5
6
7
1
4
3
11  
2
11  
9
8
9
10  
9
4
9
tine_ipb_1  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
8
74610616  
4460J  
132728  
6555J  
Bolt, Hex 3/8-24 x 1  
Tine, Outer, R.H.  
Assembly, Hub and Plate, R.H.  
Tine, Inner, R.H.  
1
2
3
4
5
6
7
4459J  
Tine, Outer, L.H.  
9
132673  
6554J  
Clevis Pin  
10  
11  
Tine, Inner, L.H.  
Clip, Hairpin  
Assembly, Hub and Plate, L.H.  
Nut, Hex 3/8-24  
Washer, Lock 3/8  
3146R  
132727  
73610600  
10040600  
NOTE: All component dimensions given in U.S. inches.  
1 inch = 25.4 mm  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TILLER - - MODEL NUMBER WET6500A  
DECALS  
1
3
4
10  
6
5
12  
9
KEY PART  
NO. NO.  
DESCRIPTION  
1
162846  
Decal, Logo  
3
186761  
143678  
141907  
102180X  
141906  
156199  
162215  
186100  
186101  
Decal, Logo  
4
Decal, Instruction, Tilling  
Decal, Hand Placement  
Decal, Shift Indicator  
Decal, Warning, Rotating Tines  
Deal, Reverse  
Decal, Tine Shield Wrng Dom  
Manual, Owner's (English)  
Manual, Owner's (Spanish)  
5
6
9
10  
12  
- -  
- -  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIMITED WARRANTY  
The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from de-  
fects in materials and workmanship. For a period of two (2) years from date of purchase by the original consumer  
purchaser, we will repair or replace, at our option, without charge for parts or labor incurred in replacing parts, any  
part which we find to be defective due to materials or workmanship. This Warranty is subject to the following limita-  
tions and exclusions.  
1. This warranty does not apply to the engine or components parts thereof. Please refer to the applicable manu-  
facturer's warranty on these items.  
2. Transportation charges for the movement of any power equipment unit or attachment are the responsibility of  
the purchaser. Transportation charges for any parts submitted for replacement under this warranty must be paid  
by the purchaser unless such return is requested by Electrolux Home Products.  
3. The Warranty period for any products used for rental or commercial purposes is limited to 90 days from the date  
of original purchase.  
4. ThisWarranty applies only to products which have been properly assembled, adjusted, operated, and maintained  
in accordance with the instructions furnished. This Warranty does not apply to any product which has been  
subjected to alteration, misuse, abuse, improper assembly or installation, delivery damage, or to normal wear  
of the product.  
5. Exclusions: Excluded from this Warranty are belts, tines, tine adapters, normal wear, normal adjustments, stan-  
dard hardware and normal maintenance.  
6. In the event you have a claim under this Warranty, you must return the product to an authorized service deal-  
er.  
Should you have any unanswered questions concerning this Warranty, please contact:  
In Canada contact:  
Electrolux Canada Corp.  
7075 Ordan Drive  
Mississauga, Ontario  
L5T 1K6  
Electrolux Home Products, Inc.  
Outdoor Products Customer Service Dept.  
250 Bobby Jones Expressway  
Augusta, GA 30909 USA  
giving the model number, serial number and date of purchase of your product and the name and address of the  
authorized dealer from whom it was purchased.  
THIS WARRANTY DOES NOT APPLY TO INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED  
WARRANTIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR OUR EXPRESSED WAR-  
RANTIES. Some areas do not allow the limitation of consequential damages or limitations of how long an implied  
Warranty may last, so the above limitations or exclusions may not apply to you.This Warranty gives you specific legal  
rights, and you may have other rights which vary from locale to locale.  
This is a limited Warranty within the meaning of that term as defined in the Magnuson-Moss Act of 1975.  
®
01029-weedeater  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Weed Eater Trimmer 530088895 User Manual
Weed Eater Trimmer 545137261 User Manual
Whirlpool Oven WOS51EC0A User Manual
Whirlpool Washer Dryer W10376238C User Manual
Whynter Refrigerator BWR 171DS User Manual
Woodstock Saw W1761 User Manual
Yamaha Microcassette Recorder MD8 User Manual
Yamaha Stereo Amplifier DSP AZ1 User Manual
Zanussi Ventilation Hood ZHT 610 User Manual
Zenoah Trimmer CHTZ6000 User Manual