Toshiba Personal Computer
Satellite E200/E205
(PSE20)
(PSE25)
Maintenance Manual
TOSHIBA CORPORATION
S/ No
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
This maintenance manual describes how to perform hardware service maintenance for the
Toshiba Personal Computer Satellite E200/E205, referred to as Satellite E200/E205 in this
manual.
The procedures described in this manual are intended to help service technicians isolate
faulty Field Replaceable Units (FRUs) and replace them in the field.
SAFETY PRECAUTIONS
Four types of messages are used in this manual to bring important information to your
attention. Each of these messages will be italicized and identified as shown below.
DANGER: “Danger” indicates the existence of a hazard that could result in death or
serious bodily injury, if the safety instruction is not observed.
WARNING: “Warning” indicates the existence of a hazard that could result in bodily
injury, if the safety instruction is not observed.
CAUTION: “Caution” indicates the existence of a hazard that could result in property
damage, if the safety instruction is not observed.
NOTE: “Note” contains general information that relates to your safe maintenance
service.
Improper repair of the computer may result in safety hazards. Toshiba requires service
technicians and authorized dealers or service providers to ensure the following safety
precautions are adhered to strictly.
Be sure to fasten screws securely with the right screwdriver. If a screw is not fully
fastened, it could come loose, creating a danger of a short circuit, which could cause
overheating, smoke or fire.
If you replace the battery pack, RTC battery or backup battery, be sure to use only the
same model battery or an equivalent battery recommended by Toshiba. Installation of
the wrong battery can cause the battery to explode.
Satellite/E200/E205 Maintenance Manual
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
The manual is divided into the following parts:
Chapter 1
Chapter 2
Chapter 3
Chapter 4
Hardware Overview describes the Satellite E200/E205 system unit and
each FRU.
Troubleshooting Procedures explains how to diagnose and resolve
FRU problems.
Test and Diagnostics describes how to perform test and diagnostic
operations for maintenance service.
Replacement Procedures describes the removal and replacement of the
FRUs.
Appendices The appendices describe the following:
Handling the LCD module
Board layout
Pin Assignments
Keyboard scan/character codes
Key layout
iv
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Conventions
This manual uses the following formats to describe, identify, and highlight terms and
operating procedures.
Acronyms
On the first appearance and whenever necessary for clarification acronyms are enclosed in
parentheses following their definition. For example:
Read Only Memory (ROM)
Keys
Keys are used in the text to describe many operations. The key top symbol as it appears on
the keyboard is printed in boldface type.
Key operation
Some operations require you to simultaneously use two or more keys. We identify such
operations by the key top symbols separated by a plus (+) sign. For example, Ctrl + Pause
(Break) means you must hold down Ctrl and at the same time press Pause (Break). If
three keys are used, hold down the first two and at the same time press the third.
User input
Text that you are instructed to type in is shown in the boldface type below:
DISKCOPY A: B:
The display
Text generated by the XXXXX that appears on its display is presented in the type face
below:
Format complete
System transferred
Satellite/E200/E205 Maintenance Manual
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Chapter 1
Hardware Overview
1.1 Features..............................................................................Error! Bookmark not defined.
1.2 System Unit Components ..................................................Error! Bookmark not defined.
1.3 2.5-inch HDD.....................................................................Error! Bookmark not defined.
1.4 DVD Super Multi (+-R Double Layer)..............................Error! Bookmark not defined.
1.5 Power Supply.....................................................................Error! Bookmark not defined.
1.6 Batteries .............................................................................Error! Bookmark not defined.
1.6.1
1.6.2
1.6.3
Main Battery...........................................Error! Bookmark not defined.
Battery Charging Control.......................Error! Bookmark not defined.
RTC Battery ...........................................Error! Bookmark not defined.
Chapter 2
Troubleshooting
2.1
2.2
2.3
Outline......................................................................Error! Bookmark not defined.
Basic Flowchart........................................................Error! Bookmark not defined.
Power Supply ...........................................................Error! Bookmark not defined.
Procedure 1 Power Icon Check.............................Error! Bookmark not defined.
Procedure 2 Connection Check.............................Error! Bookmark not defined.
Procedure 3 Replacement Check ..........................Error! Bookmark not defined.
System Board ...........................................................Error! Bookmark not defined.
Procedure 1 Message Check.................................Error! Bookmark not defined.
Procedure 2 Test Program Check .........................Error! Bookmark not defined.
Procedure 3 Replacement Check ..........................Error! Bookmark not defined.
HDD .........................................................................Error! Bookmark not defined.
Procedure 1 Message Check.................................Error! Bookmark not defined.
Procedure 2 Partition Check .................................Error! Bookmark not defined.
Procedure 3 Format Check....................................Error! Bookmark not defined.
Procedure 4 Test Program Check .........................Error! Bookmark not defined.
2.4
2.5
vi
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Procedure 5 Connector Check and Replacement Check..... Error! Bookmark not
defined.
2.6
2.7
Keyboard ..................................................................Error! Bookmark not defined.
Procedure 1 Test Program Check .........................Error! Bookmark not defined.
Procedure 2 Connector Check and Replacement Check..... Error! Bookmark not
defined.
Display .....................................................................Error! Bookmark not defined.
Procedure 1 External Monitor Check ...................Error! Bookmark not defined.
Procedure 2 Test Program Check .........................Error! Bookmark not defined.
Procedure 3 Connector Check and Replacement Check..... Error! Bookmark not
defined.
2.8
2.9
ODD (Optical Disk Drive) .......................................Error! Bookmark not defined.
Procedure 1 ODD Cleaning Check.......................Error! Bookmark not defined.
Procedure 2 Test Program Check .........................Error! Bookmark not defined.
Procedure 3 Connector Check and Replacement Check..... Error! Bookmark not
defined.
LAN..........................................................................Error! Bookmark not defined.
Procedure 1 Test Program Check .........................Error! Bookmark not defined.
Procedure 2 Connector Check and Replacement Check..... Error! Bookmark not
defined.
2.10
2.11
Finger Print (Optional).............................................Error! Bookmark not defined.
Procedure 1 Test Program Check .........................Error! Bookmark not defined.
Procedure 2 Connector Check ..............................Error! Bookmark not defined.
Audio Test................................................................Error! Bookmark not defined.
Procedure 1 Test Program Check .........................Error! Bookmark not defined.
Procedure 2 Connector Check and Replacement Check..... Error! Bookmark not
defined.
2.12
2.13
IEEE 1394 Test ........................................................Error! Bookmark not defined.
Procedure 1 Test Program Check .........................Error! Bookmark not defined.
Procedure 2 Connector Check ..............................Error! Bookmark not defined.
Cooling Module........................................................Error! Bookmark not defined.
Procedure 1 Test Program Check .........................Error! Bookmark not defined.
Procedure 2 Connector Check and Replacement Check..... Error! Bookmark not
defined.
Satellite/E200/E205 Maintenance Manual
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Diagnostic Programs
3.1
3.2
General .....................................................................Error! Bookmark not defined.
Quick Start................................................................Error! Bookmark not defined.
3.2.1
3.2.2
3.2.3
3.2.4
3.2.5
3.2.6
3.2.7
3.2.8
3.2.9
Quick Test ..............................................Error! Bookmark not defined.
Customization Test.................................Error! Bookmark not defined.
Keyboard Layout test .............................Error! Bookmark not defined.
Hotkey Test ............................................Error! Bookmark not defined.
Audio Play Test......................................Error! Bookmark not defined.
Audio Record Test .................................Error! Bookmark not defined.
DMI Read...............................................Error! Bookmark not defined.
DMI Write..............................................Error! Bookmark not defined.
3D Sensor Test .......................................Error! Bookmark not defined.
3.2.10 System Information................................Error! Bookmark not defined.
3.2.11 View Logs ..............................................Error! Bookmark not defined.
3.2.12 Exit to Free DOS...................................Error! Bookmark not defined.
3.2.13 The Diagnostics Screen Explanation......Error! Bookmark not defined.
3.3
Options .....................................................................Error! Bookmark not defined.
3.3.1
3.3.2
3.3.3
3.3.4
3.3.5
3.3.6
3.3.7
3.3.8
3.3.9
Overview ................................................Error! Bookmark not defined.
Batch Parameters Configuration ............Error! Bookmark not defined.
Item’s Parameters Configuration ...........Error! Bookmark not defined.
Load Batch Parameters...........................Error! Bookmark not defined.
Save Batch Parameters...........................Error! Bookmark not defined.
LOG Parameters Setting.........................Error! Bookmark not defined.
Specify LOG Viewer..............................Error! Bookmark not defined.
Display LOG File...................................Error! Bookmark not defined.
LOG Viewer...........................................Error! Bookmark not defined.
3.3.10 LOG File Sample ...................................Error! Bookmark not defined.
Subtests.....................................................................Error! Bookmark not defined.
System Test ..............................................................Error! Bookmark not defined.
3.4
3.5
viii
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3.6
Memory Test ............................................................Error! Bookmark not defined.
Storage......................................................................Error! Bookmark not defined.
Video ........................................................................Error! Bookmark not defined.
Communication (COMM)........................................Error! Bookmark not defined.
Peripheral .................................................................Error! Bookmark not defined.
Error Codes and description.....................................Error! Bookmark not defined.
Quick Test Item List.................................................Error! Bookmark not defined.
3.7
3.8
3.9
3.10
3.11
3.12
Chapter 4
4.1
Replacement Procedures
General .....................................................................Error! Bookmark not defined.
Safety Precautions..................................................Error! Bookmark not defined.
Before You Begin ..................................................Error! Bookmark not defined.
Disassembly Procedures ........................................Error! Bookmark not defined.
Assembly Procedures.............................................Error! Bookmark not defined.
Tools and Equipment .............................................Error! Bookmark not defined.
Screw Tightening Torque ......................................Error! Bookmark not defined.
Colors of Screw Shanks.........................................Error! Bookmark not defined.
Symbols of Screws on the Computer Body ...........Error! Bookmark not defined.
Symbol examples...................................................Error! Bookmark not defined.
Battery Pack/Bridge Media ......................................Error! Bookmark not defined.
4.2
4.2.1
Battery Pack ...........................................Error! Bookmark not defined.
Removing the Battery Pack ...................................Error! Bookmark not defined.
Installing the Battery Pack.....................................Error! Bookmark not defined.
4.2.2
Bridge Media (SD Card / Memory Stick / xDPicture Card).......... Error!
Bookmark not defined.
Removing the Bridge Media..................................Error! Bookmark not defined.
Installing the Bridge Media ...................................Error! Bookmark not defined.
Keyboard ..................................................................Error! Bookmark not defined.
Removing Keyboard ..............................................Error! Bookmark not defined.
Installing the Keyboard..........................................Error! Bookmark not defined.
Bottom Cover ...........................................................Error! Bookmark not defined.
Removing the Bottom Cover .................................Error! Bookmark not defined.
4.3
4.4
Satellite/E200/E205 Maintenance Manual
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Bottom Cover...................................Error! Bookmark not defined.
Display Assembly ....................................................Error! Bookmark not defined.
Removing the Display Assembly...........................Error! Bookmark not defined.
Installing the Display Assembly............................Error! Bookmark not defined.
Memory Module.......................................................Error! Bookmark not defined.
Removing the Memory Module.............................Error! Bookmark not defined.
Installing the Memory Module ..............................Error! Bookmark not defined.
Wireless LAN Card..................................................Error! Bookmark not defined.
Removing the Wireless LAN Card........................Error! Bookmark not defined.
Installing the Wireless LAN Card .........................Error! Bookmark not defined.
HDD .........................................................................Error! Bookmark not defined.
Removing the HDD ...............................................Error! Bookmark not defined.
Installing the HDD.................................................Error! Bookmark not defined.
ODD Bay Module ....................................................Error! Bookmark not defined.
Removing the ODD Bay Module ..........................Error! Bookmark not defined.
Installing the ODD Bay Module............................Error! Bookmark not defined.
Disassembling the ODD Drive ..............................Error! Bookmark not defined.
Assembling the ODD Drive...................................Error! Bookmark not defined.
Bluetooth module .....................................................Error! Bookmark not defined.
Removing the Bluetooth module ...........................Error! Bookmark not defined.
Installing the Bluetooth Module ............................Error! Bookmark not defined.
CPU Cooling Module and Fan.................................Error! Bookmark not defined.
Remove the CPU cooling module and Fan............Error! Bookmark not defined.
Installing the CPU Cooling Module and Fan.........Error! Bookmark not defined.
CPU ..........................................................................Error! Bookmark not defined.
Removing the CPU ................................................Error! Bookmark not defined.
Installing the CPU..................................................Error! Bookmark not defined.
System Board ...........................................................Error! Bookmark not defined.
Removing the System Board .................................Error! Bookmark not defined.
Installing the System Board...................................Error! Bookmark not defined.
Speakers ...................................................................Error! Bookmark not defined.
Removing the Speakers..........................................Error! Bookmark not defined.
4.5
4.6
4.7
4.8
4.9
4.10
4.11
4.12
4.13
4.14
x
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Speakers...........................................Error! Bookmark not defined.
Switch Board and Finger Print Board ......................Error! Bookmark not defined.
Removing Switch Board and Finger Print Board ..Error! Bookmark not defined.
Installing Switch Board and Finger Print Board....Error! Bookmark not defined.
Light Sensor Board and Audio Board......................Error! Bookmark not defined.
4.15
4.16
Removing the Light Sensor Board and Audio Board.......... Error! Bookmark not
defined.
Installing the Power Board, Switch Board and Logo LED Board................. Error!
Bookmark not defined.
4.17
DC-IN cable, RGB Board and RJ45 cable...............Error! Bookmark not defined.
Removing DC-IN cable, RGB Board and RJ45 cable......... Error! Bookmark not
defined.
Installing DC-IN cable, RGB Board and RJ45 cable .......... Error! Bookmark not
defined.
4.18
4.19
Display Mask............................................................Error! Bookmark not defined.
Open Display Mask................................................Error! Bookmark not defined.
Removing the Display Mask..................................Error! Bookmark not defined.
Installing the Display Mask ...................................Error! Bookmark not defined.
LCD Module.............................................................Error! Bookmark not defined.
Open LCD module.................................................Error! Bookmark not defined.
Removing the LCD module...................................Error! Bookmark not defined.
Installing the LCD Module....................................Error! Bookmark not defined.
CCD Board and MIC................................................Error! Bookmark not defined.
Removing the CCD Board and MIC......................Error! Bookmark not defined.
Installing the CCD Board and MIC .......................Error! Bookmark not defined.
LED Board and Card Reader Board.........................Error! Bookmark not defined.
4.20
4.21
Removing the LED Board and Card Reader Board............. Error! Bookmark not
defined.
Installing the LED Board and Card Reader Board Error! Bookmark not defined.
Satellite/E200/E205 Maintenance Manual
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Appendix A Handling the LCD Module ........................................................................... A-1
Appendix B Board Layout .................................................................................................B-1
Appendix C Pin Assignments.............................................................................................C-1
Appendix D Keyboard Scan/Character Codes .................................................................. D-1
Appendix E Key Layout.....................................................................................................E-1
xii
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Hardware Overview
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Hardware Overview
ii
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Hardware Overview
Chapter 1
Contents
1.1 Features............................................................................................................................... 5
1.5 Power Supply.................................................................................................................... 19
Satellite/E200/E205 Maintenance Manual
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Hardware Overview
Figures
Figure 1-4 System Unit Block Diagram..................................................................................12
Tables
Table 1-2 DVD Super Multi Drive Specifications..................................................................18
iv
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1.1 Features
1 Hardware Overview
1.1 Features
Toshiba Satellite E200/E205 is a full size notebook PC based on the mobile Intel Arrandale
Processor, providing high-speed processing capabilities and advanced features. The computer
employs a Lithium Ion battery that allows it to be battery-operated for a longer period of time.
The display uses 14.0-inch WXGA HD LCD panel, at a resolution of 1366x768. The Micro-
PGA Socket supports BTO/CTO for the CPU so that the system can be designed to suit your
needs.
The computer has the following features:
Processor
CPU is mobile Intel Arrandale Processor:
Intel Core I5 CPU (1066MHz FSB)
I5-520M(2.40G) Hz
Intel Core I3 CPU (1066MHz FSB)
I3-330M(2.13G) Hz
I3-350M(2.26G) Hz
Host Bridge System Controller
System Controller: Intel 5 Series Chipset HM55, HM57.
Graphics
Intel integrated graphics or nVIDIA N11M-GE1 / N11M-LP1 graphics.
Memory
The computer has two SO-DIMM slots, which come standard with DDR3-1066MHz
(PC3-8500) memory module. DDR3 is driven at 1.5V. It accepts BTO/CTO for your
memory requirements. It can incorporate up to 8.0GB of main memory.
Using the following sizes of memory modules:
1024 MB (128M64) / DDR3-1066MHz
2048 MB (256M64) / DDR3-1066MHz
Satellite/E200/E205 Maintenance Manual
5
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Hardware Overview
1.1 Features
4096 MB (512M64) / DDR3-1066MHz
Hard Disk Drive (HDD)
The computer accommodates 2.5-inch 9.5mm height Serial ATA HDD with following
storage capacities:
160 GB (9.5mm thick) SATA (5,400rpm)
250 GB (9.5mm thick) SATA (5,400rpm)
320 GB (9.5mm thick) SATA (5,400rpm)
400 GB (9.5mm thick) SATA (5,400rpm)
500 GB (9.5mm thick) SATA (5,400rpm)
ODD
The computer accommodates a fixed 12.7mm ODD with the following type:
Slot Loading Type DVD Super Multi +-R Double Layer with Label Flash™ drive
Display
LCD display comes in the following type at resolution 1366x768:
14.0” WXGA HD 1366x768 CSV LED display
On-Board LAN
The internal LAN supports 10/100Mbit Ethernet, enabling connection to a LAN at up to
100Mbps. It supports Wake-up on LAN from S3/S4/S5 and PXE boot support. This
internal LAN has RJ45 jack to directly accommodate a LAN cable, and there is signal
reception LED on RJ45 jack.
Wireless LAN (BTO)
The internal Mini Card slot supports IEEE802.11agn (MOW) / IEEE802.11agn (JPN) /
IEEE802.11bg (WW) / IEEE802.11bgn (WW) cards. The Antenna has two or three
wires dual band antenna support for BTO.
Sound System
6
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1.1 Features
1 Hardware Overview
Realtek ALC272 integrated audio controller supports multimedia. The sound system
contains the following:
Stereo speakers
Headphone / SPDIF combo jack
Internal microphone
External microphone jack
Keyboard
30 kinds’ countries keyboard, which is Toshiba B5 one.
Toshiba Touch Pad
Wide Touch Pad.
Bluetooth (BTO)
Bluetooth wireless technology eliminates the need for cables between electronic device
such as desktop computer, printer and mobile phone.
eSATA / USB Combo Port
This product has one eSATA / USB Combo port, which allows device connection
through either eSATA or USB signals of eSATA / USB Combo Port.
USB Port
The computer has two USB 2.0 ports. It is supported to daisy-chain a maximum of 127
USB devices. The serial data transfer rate is 480Mbps, 12Mbps and 1.5Mbps. These
ports support PnP installation and hot plugging.
RGB External Monitor Port
A 15-pin external monitor port is provided, through which the computer automatically
recognizes an external VESA DDC 2B compatible monitor.
HDMI Out Port
A HDMI monitor can be connected to HDMI Out Port on the computer.
Satellite/E200/E205 Maintenance Manual
7
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Hardware Overview
1.1 Features
Bridge Media Slot
This slot is for your memory card requirements like SD, Mini-SD, SD-IO, MS, MS Pro,
MMC and XD Cards to provide memory card read on your computer.
Webcam (BTO)
The computer has an internal camera. It supports VGA (640x480) without Macro
module.
Battery
The computer has a removable 6 Cell Lithium Ion battery pack and an internal RTC
battery (rechargeable).
8
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1.2 System Unit Components
1 Hardware Overview
The system unit of the computer consists of the following components:
Processor: Mobile Intel Arrandale Processor.
Intel Core I5 Processor (FSB, 1066MHz)
Core Speed: 2.40 GHz
System Bus: 1066 MHz
On-Die Level 2 Cache: 3 MB
Intel Core I3 Processor (FSB, 1066MHz)
Core Speed: 2.13/2.26 GHz
System Bus: 1066 MHz
On-Die Level 2 Cache: 3 MB
Memory: Two expansion memory slots are provided. They can hold 1.0/2.0/4.0GB memory
modules available as options to grow up to 8.0GB.
PC3-8500 (1066MHz) DDR3 SDRAM supported
1024/2048/4096MB modules supported
1024 MB (128M x 64)
2048 MB (256M x 64)
4096 MB (512M x 64)
DDR3 1.5 volt operation
No parity bit
64-bit data transfer
BIOS ROM (Flash EEPROM)
12Mb x 1 chip (1536KB flash parts)
NvStorage Size : 64K
NvStorage Free Space : 63K
FV00 Size : 992K
FV00 Free Space : 127K
FV01 Size : 384K
FV01 Free Space : 85K
System Controller
Mobile Intel 5 Series Chipset HM55 / HM57 PCH
Direct Media Interface (DMI)
PCI Express Interface
Satellite/E200/E205 Maintenance Manual
13
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Hardware Overview
1.2 System Unit Components
Integrated Serial ATA (SATA) Host Controller
Intel High Definition Audio Controller
Simple Serial Transport (SST) 1.0 Bus
Platform Environmental Control Interface (PECI)
Universal Serial Bus (USB) Controller
Integrated Gigabit LAN Controller
Intel Active Management Technology with System Defense
Intel I/O Virtualization (VT-d) Support
Intel Trusted Execution Technology Support
Power Management Logic
External Glue Integration
Enhanced DMA Controller
System Management Bus
High Precision Event Timers
Timers Based on 82C54
Real-Time Clock
System TCO Reduction Circuits
Serial Peripheral Interface (SPI) Support
Interrupt Controller
Firmware Hub Interface Support
Low Pin Count (LPC) I/F
GPIO
Analog and Digit Display Ports
JTAG Boundary Scan Support
Audio Controller
Realtek ALC272 integrated audio controller supports multimedia. The sound system
features contain the following:
2 Stereo DACs support 16/20/24-bit PCM format for stereo audio playback
2 stereo ADCs support 16/20-bit PCM format for two stereo independent sound inputs
16/20/24-bit S/PDIF-OUT supports 44.1K/48K/88.2K/96K/192KHz sample rate
All ADCs support 44.1K/48K/96KHZ sample rate
4 GPIOs (GPIO0/GPIO3 are digital GPIO shared with digital MIC interface,
GPIO1/GPIO2 are analog) for customized applications
High quality analog differential CD input
2 jack detection pins each designed to detect up to 4 jacks
Supports hardware digital volume control for digital microphone input
Supports external PCBEEP input and built-in digital BEEP generator
14
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1.2 System Unit Components
1 Hardware Overview
KBC/EC (Keyboard Controller/Embedded Controller)
A KBC WINBOND WPCE781L chip is used to serve as KBC/EC and Super IO:
KBC
Scan controller function
Interface controller function
EC
Power supply sequence control
Overheat shutdown support
LED control
Beep control
Device ON/OFF
Cooling fan speed control
Universal I/O port
Battery capacity check
Flash memory reprogramming function
EC access interface
I2C communication control
Battery EEPROM
24C02 equivalent (128 words x 16 bits, I2C interface) integrated in battery pack
Storing records of battery use
Clock Generator
ICS ICS9LRS3197
Generating the clock signal required for the system
LAN Controller
Atheros AR8152-AL1 - 10/100Mbit
IEEE802.3 10BASE-T/100BASE-TX physical layer interface
IEEE 802.3u Auto-Negotiation support
Digital Adaptive Equalization control
10BASE-T auto-polarity correction
LAN Connect interface
Automatic detection of “unplugged mode”
Remote boot (PXE 2.1)
Smart power down when link is not detected
Satellite/E200/E205 Maintenance Manual
15
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Hardware Overview
1.2 System Unit Components
Wireless LAN Controller
Support following 3 kinds of mini PCI wireless LAN cards
IEEE 802.11bg
IEEE 802.11ag
IEEE 802.11agn
Data Rate
IEEE 802.11bg: Standard 54M bps
IEEE 802.11ag: Standard 54M bps
IEEE 802.11agn: Standard 130M bps
Frequency Channel
IEEE802.11bg: 2.4GHz
IEEE802.11ag: 2.4GHz / 5.4GHz
IEEE802.11agn: 2.4GHz / 5.4GHz
16
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1.3 2.5-inch HDD
1 Hardware Overview
1.3 2.5-inch HDD
The computer contains an extremely low-profile, lightweight and high-performance HDD.
The HDD incorporates 9.5 mm height magnetic disk and mini-Winchester type magnetic
heads. The HDD interface conforms to Serial ATA. Storage capacities supported are 160,
250, 320, 400 & 500GB.
The HDD is shown in Figure 1-5 and some of its specifications are listed in Table 1-1.
Figure 1-5 SATA HDD
Table 1-1 HDD Specifications
Item
Capacity (GB)
Rotational Speed (RPM)
Height
Specifications
250 GB
160 GB
5400 rpm
9.5 mm
320 GB
5400 rpm
9.5 mm
5400 rpm
9.5 mm
User Data Sectors
Bytes / Sector
Item
312,581,808
512
488,397,168
512
625,142,448
512
Specifications
500 GB
Capacity (GB)
Rotational Speed (RPM)
Height
400 GB
5400 rpm
9.5 mm
5400 rpm
9.5 mm
User Data Sectors
Bytes / Sector
781,422,768
512
976,773,168
512
Satellite/E200/E205 Maintenance Manual
17
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Hardware Overview
1.4 DVD Super Multi (+-R Double Layer)
1.4 DVD Super Multi (+-R Double Layer)
The DVD Super Multi drive accepts 12-cm (4.72-inch) and 8-cm (3.15-inch) discs. At
maximum, the drive can play back a DVD at 8x speed, read CD-ROM at 24x speed, and
write CD-R at 24x speed, CD-RW at 4x speed, US CD-RW at 24x speed, High Speed CD-
RW at 10x speed, DVD-R at 8x speed, DVD-RW at 6x speed, DVD+R at 8x speed, DVD+R
(Double Layer) at 4x speed, DVD-R (Double Layer) at 4x speed, DVD+RW at 8x speed and
DVD-RAM at 5x speed.
DVD Super Multi Drive is shown in Figure 1-6 and its specifications are listed in Table 1-2.
Figure 1-6 DVD Super Multi Drive
Table 1-2 DVD Super Multi Drive Specifications
Item
DVD-ROM mode
CD-ROM mode
Data Transfer Rate
(Mbytes/s)
33.3 (U-DMA transfer mode 2)
16.7 (PIO mode 4, Multiword DMA mode 2)
Access Time (ms)
Average Random
Access
130 ms
130 ms
Data Buffer Size
(Mbytes)
2MB
Formats Supported
DVD:
DVD-VIDEO, DVD-ROM, DVD-R, DVD-RW, DVD-RAM,
DVD+R, DVD+-R (Double Layer), DVD+RW.
CD:
CD-DA, CD-ROM, CD-R, CD-RW, CD-ROMXA, Photo CD (Multi-
Session), Video CD, CD-Extra (CD+), CD-Text.
18
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 Power Supply
1 Hardware Overview
1.5 Power Supply
The power supply unit provides many different voltages for the system board and performs the
following functions:
1. Power input monitor
Checks whether the DC power supply (AC adapter) is connected to the computer.
Checks whether the battery pack is connected to the computer.
Monitors the DC power supply input voltage (AC Adapter output voltage).
2. Power supply's internal control
Turns on and off the battery pack charging power supply.
Issues a charging current instruction to the PWM control IC of the battery pack charging
power supply.
Controls the supply of DC power supply input (AC Adapter output) to the power supply
unit.
Controls the supply of power to the system block (load/logic circuit side).
Controls forced shutdown if the power supply malfunctions.
3. Logic circuit control
Instructs the gate array to enable/disable tuning the power on.
Controls power-on/off operation.
4. Status display
Turns on the Power LED (in White).
Battery indicator (in White or Umber or Umber Flash).
5. External interface
Performs communication through the I2C bus (via the internal EC/KBC).
Transfers the power supply operation mode.
6. Output monitor
Monitors the voltage output to the system block (load/logic circuit side).
Monitors the voltage, over voltage, input/output current of the battery pack.
Monitors the internal temperature of the battery pack.
Monitors the supply voltage from the AC adapter.
Satellite/E200/E205 Maintenance Manual
19
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Hardware Overview
1.6 Batteries
1.6 Batteries
The computer has the following 3 types of batteries:
Main Battery Pack
Real Time Clock (RTC) Battery
Table 1-3 lists the specifications of these batteries.
Table 1-3 Battery Specifications
Battery Type
Main Battery Pack
RTC Battery
Material
Output voltage
Capacity
5600 mAh
5800 mAh
6 Cell
Lithium Ion
10.8 V
3.0 V
Lithium Ion
14 mAh
1.6.1
1.6.2
Main Battery
The main battery pack serves as the computer's main power source when the AC adapter
is not attached. The main battery maintains the state of the computer so that it can
resume it.
Battery Charging Control
Battery charging is controlled by TI BQ24721C. When AC adapter and battery pack are
attached to the computer, the BQ24721C controls the charge on/off state and detects a
full charge.
Battery Charge
When the AC adapter is attached, the battery is charged by off-state charge when the
system is powered off or by on-state charge when it is powered on.
20
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1.6 Batteries
1 Hardware Overview
Table 1-4 Quick/Normal Charging Time
State
Charge Time
Off-State Charge
On-State Charge
6 Cell
6 Cell
About 4 hours max
About 4~10 hours max
NOTE: The time required for normal charge depends on the power consumption by the
system. Using the fluorescent lamp and frequently accessing the disk consume much
power and lengthen the charge time.
Any of the following cases stops battery charge:
1. The battery becomes fully charged.
2. The AC adapter or battery pack is removed.
3. The battery or AC adapter voltage is abnormal.
Detection of full charge
A full charge is detected only when the battery is being charged by quick or normal
charge. A full charge is detected when either of the following conditions is met:
1. The current in the battery charging circuit drops below the predetermined
value.
2. The charging time exceeds the fixed limit.
1.6.3
RTC Battery
The RTC battery provides power to keep the current date, time and other system
information in memory while the computer is turned off.
Satellite/E200/E205 Maintenance Manual
21
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting
2
概要
Chapter 2
Troubleshooting
2-i
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting
Chapter 2
Contents
Outline.................................................................................................................... 2-1
Procedure 1 Power Icon Check....................................................................... 2-6
Procedure 2 Connection Check....................................................................... 2-8
Procedure 3 Replacement Check .................................................................... 2-8
Procedure 1 Message Check........................................................................... 2-9
Procedure 2 Test Program Check ................................................................. 2-10
Procedure 3 Replacement Check .................................................................. 2-10
Procedure 1 Message Check......................................................................... 2-11
Procedure 2 Partition Check ......................................................................... 2-11
Procedure 3 Format Check............................................................................ 2-12
Procedure 4 Test Program Check ................................................................. 2-13
Procedure 1 Test Program Check ................................................................. 2-15
Procedure 2 Test Program Check ................................................................. 2-16
Procedure 2 Test Program Check ................................................................. 2-18
Procedure 1 Test Program Check ................................................................. 2-20
2-ii
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting
Finger Print (Optional)......................................................................................... 2-21
Procedure 1 Test Program Check ................................................................. 2-21
Procedure 2 Connector Check ...................................................................... 2-21
Audio Test............................................................................................................ 2-22
Procedure 1 Test Program Check ................................................................. 2-22
Procedure 1 Test Program Check ................................................................. 2-23
Procedure 2 Connector Check ...................................................................... 2-23
Procedure 1 Test Program Check ................................................................. 2-24
Satellite/E200/E205 Maintenance Manual
2-iii
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting
Figures
Tables
2-iv
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2.1 Outline
2 Troubleshooting
2.1 Outline
This chapter describes the fault diagnosis procedures for field replaceable units (FRUs) in the
computer.
The FRUs covered here are as follows:
1. System board
4. Display
7. Finger Print
10. Cooling module
2. HDD
5. ODD drive
8. Speaker
3. Keyboard
6. LAN
9. IEEE 1394
See Chapter 4 for the procedures to replace FRUs and Chapter 3 for the procedures to use test
programs.
The following tools are required to perform the diagnostic procedures:
1. Diagnostics (maintenance test program) disk
2. Phillips screwdrivers (2 mm, 2.5 mm)
3. Cleaning disk kit (for ODD drive cleaning)
4. Bootable CD
5. Multi-meter
6. External monitor
7. Headphone
8. Microphone
9. A-BEX TEST DVD
10. Music CD
11. DVD TSD-1 (TOSHIBA EMI DVD Test Media)
Satellite/E200/E205 Maintenance Manual
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting
2.2 Basic Flowchart
2.2 Basic Flowchart
The basic flowchart in Figure 2-1 serves as a guide for identifying a possibly faulty FRU.
Before going through the diagnostic flowchart steps, verify the following:
Ask the user if a password has been registered and, if so, ask him or her to enter the
password. If the user has forgotten the system password, use a jump wire to make a
short circuit on M/B B500 location, then turn the computer power on. When booted,
the computer overrides password protection and automatically erases the current
password.
Make sure the Windows® 7 Home Edition has been installed on the HDD. Any other
operating system can cause the computer to malfunction.
Make sure any piece of optional equipment has been installed.
2-2
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2 Basic Flowchart
2 Troubleshooting
Star
t
Connect the AC Adapter
No
No
Follow the power supply diagnostic
procedure in Section 2.3
DC IN LED on ??
Yes
Follow the power supply diagnostic
procedure in Section 2.3
BATTERY LED on ??
Yes
Turn the power on.
Yes
Follow the system board diagnostic
procedure in Section 2.4
Any error message displayed ??
No
No
Follow the display diagnostic
procedure in Section 2.7
Message "In Touch with
Tomorrow Toshiba" displayed
Yes
Yes
See the previous page to
delete the password.
"Password=" displayed ??
No
Follow the HDD diagnostic
procedure in Section 2.5
OS started ??
No
Yes
1
Figure 2-1
Basic Flowchart (1/2)
Satellite/E200/E205 Maintenance Manual
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting
2.2 Basic Flowchart
1
No
No
Follow the keyboard diagnostic
procedure in Section 2.6
Keyboard works well ??
Insert Bootable CD into ODD
Follow the ODD diagnostic
procedure in Section 2.8
Diagnostic Program
Loaded ??
Yes
Perform each test with the
diagnostic program.
Yes
Identify the test resulting in the error
and perform the appropriate
diagnostic procedures
Any error detected by the
diagnostic program ??
No
Perform the continuous test to check if the
error is intermittent.
Yes
Identify the test resulting in the
error and perform the appropriate
diagnostic procedures
Any error detected by the
diagnostic program ??
No
The system is normal.
END
Figure 2-1
Basic Flowchart (2/2)
2-4
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2 Basic Flowchart
2 Troubleshooting
If the diagnostic program cannot detect an error, the error may be intermittent. Run the
continuous test program repeatedly to isolate the problem. Check the log utilities function to
confirm which diagnostic test detected the error, then perform the appropriate
troubleshooting procedures as follows:
1. If an error is detected by the System test, Memory test, Async test, Printer test,
Sound test, or Real Timer test, follow the system board troubleshooting procedures in
Section 2.4.
2. If an error is detected by the Hard Disk test, follow the HDD troubleshooting
procedures in Section 2.5.
3. If an error is detected by the Keyboard test, follow the keyboard troubleshooting
procedures in Section 2.6.
4. If an error is detected by the Display test, follow the display troubleshooting
procedures in Section 2.7.
5. If an error is detected by the ODD test, follow the ODD troubleshooting procedures in
Section 2.8.
6. If an error is detected by the LAN test, follow the LAN troubleshooting procedures in
section 2.9.
7. If an error is detected by the Finger Print test, follow the Finger Print troubleshooting
procedures in section 2.10.
8. If an error is detected by the Speaker test, follow the Speaker troubleshooting
procedures in section 2.11.
9. If an error is detected by the IEEE 1394 test, follow the IEEE 1394 troubleshooting
procedures in section 2.12.
10. If an error is detected by the Fan On/Off test, follow the cooling module
troubleshooting procedures in Section 2.13.
Satellite/E200/E205 Maintenance Manual
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting
2.3 Power Supply
2.3 Power Supply
The power supply in the computer controls many functions and components. To check if the
power supply is defective or malfunctioning, follow the troubleshooting procedures below as
instructed.
Procedure 1 Power Icon Check
Procedure 2 Connection Check
Procedure 3 Replacement Check
Procedure 1 Power Icon Check
The following two power LEDs indicate the power supply status:
Battery LED
DC IN LED
The power supply controller displays the power supply status through the Battery and DC IN
LEDs as in the tables below.
Battery LED
Battery LED
On in Umber
Power supply status
Battery being charged
On in White
Blinking in Umber
(at equal intervals)
Off
Battery fully charged, with AC adapter connected
Battery low while driving the computer
Else
2-6
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3 Power Supply
2 Troubleshooting
DC IN LED
DC IN LED
Power supply status
DC power being supplied (from the AC adapter)
Battery damage and can’t charge during DC-in.
Else
On in White
Off
Off
If the DC IN LED off, follow the steps below:
1. Remove the battery pack and the AC adapter to shut off power supply to the
computer.
2. Attach the battery and AC adapter back again.
If the LED still off, follows the steps below:
Check 1
Check 2
Make sure the DC IN LED goes on in White. If it does not, go to Procedure 2.
Make sure the Battery LED goes on in Umber or White. If it does not, go to
Procedure 3.
Satellite/E200/E205 Maintenance Manual
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting
2.3 Power Supply
Procedure 2 Connection Check
Power is supplied to the system board as illustrated below:
System board
AC
adaptor
AC power cord
AC adaptor cord
Battery pack
Follow the steps below to check whether each connector has been connected correctly:
Check 1
Check 2
Make sure the AC adaptor and AC power cord have been firmly plugged
into the DC IN socket and wall outlet, respectively. When they have been
connected correctly, perform Check 2.
Connect a new AC adaptor and AC power cord.
If the DC IN LED does not go on, go to Procedure 3.
If the battery LED does not go on, perform Check 3.
Check 3
Make sure the battery pack has been correctly installed in the computer.
If the battery LED does not go on while the battery pack has been installed
correctly, go to Procedure 3.
Procedure 3 Replacement Check
The system board, power supply board, or CPU may be faulty. Disassemble the computer
according to Chapter 4 and follow the steps below:
Check 1
Check 2
Check 3
Replace the power supply board with a new one. If the battery pack is still
not working properly, perform Check 2.
Replace the system board with a new one. If the battery pack is still not
working properly, perform Check 3.
Replace the CPU with a new one.
2-8
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4 System Board
2 Troubleshooting
2.4 System Board
To check if the system board is defective or malfunctioning, follow the troubleshooting
procedures below as instructed.
Procedure 1 Message Check
Procedure 2 Test Program Check
Procedure 3 Replacement Check
Procedure 1 Message Check
When the power is turned on, the system performs the self-diagnostic Power On Self Test
(POST) embedded in the BIOS ROM. The POST tests and initializes each IC on the system
board.
If an error message appears on the display, perform Check 1.
If there is no error message, go to Procedure 2.
If FREE-DOS or Windows 7 Home Edition is loaded normally, go to Procedure 3.
Check 1
If the following error message is displayed on the screen, press the F1 key
as prompted. These errors occur when the system configuration
preserved in the RTC memory (generally called CMOS memory) does not
match the actual configuration or when the data is lost.
If you press the F1 key as prompted by the message, the TSETUP screen
appears to set the system configuration. If the error message appears
frequently when the power is turned on, replace the RTC battery. If any
other error message is displayed, perform Check 2.
*** Bad RTC battery ***
Check system. Then press [F1] key
Check 2
If the following error message is displayed on the screen, press any key as
prompted by the message.
The error message appears when either data stored in RAM to be resumed
is lost because the battery has been exhausted or the system board is faulty.
*** Resume failure and press any key to continue ***
Satellite/E200/E205 Maintenance Manual
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting
2.4 System Board
Procedure 2 Test Program Check
The maintenance test program contains several programs for diagnosing the system board
and CPU. Execute the following test programs using the procedures described in Chapter 3.
1. System test
2. Memory test
3. Keyboard test
4. Display test
5. Hard Disk test
6. Mouse test
7. ODD test
8. Sound test
9. LAN test
If an error is detected during these tests, go to Procedure 3.
Procedure 3 Replacement Check
The system board, memory, or CPU may be defective. Disassemble the computer following
the steps described in Chapter 4 and replace the system board, memory module or CPU with
a new one.
2-10
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2.5 HDD
2 Troubleshooting
2.5 HDD
To check if the 9.5mm or 12.5mm HDD is defective or malfunctioning, follow the
troubleshooting procedures below as instructed.
Procedure 1 Message Check
Procedure 2 Partition Check
Procedure 3 Format Check
Procedure 4 Test Program Check
Procedure 5 Connector Check and Replacement Check
CAUTION: The contents of the HDD will be erased when the HDD diagnostic test or
formatting is executed. Save the required contents of the HDD to floppy disks or other
storage drive in advance.
Procedure 1 Message Check
When the computer's HDD does not function properly, some of the following error messages
may appear on the display. Follow the steps below to check the HDD.
Check 1
If either of the following messages appears, go to Procedure 2. If the
following messages do not appear, perform Check 2.
Insert system disk in drive
Press any key when ready .....
or
Non-System disk or disk error
Replace and press any key
Check 2
Check SETUP to see if the Hard Disk option has been set to “Not used”. If
so, choose another setting and restart the computer. If the problem
persists, go to Procedure 2.
Procedure 2 Partition Check
Boot from the DOS system. Perform the following checks:
Check 1
Check 2
Type C: and press the Enter key. If you cannot change to drive C,
perform Check 2. If you can change to drive C, perform Check 3.
Type FDISK and press the Enter key. Choose “Display partition
information” from the FDISK menu. If drive C is listed, perform Check 3.
If drive C is not listed, return to the FDISK menu and choose the option to
Satellite/E200/E205 Maintenance Manual
2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting
2.5 HDD
create a DOS partition on drive C. Then restart the computer.. If the
problem persists, go to Procedure 3.
Check 3
Check 4
If drive C is listed as active in the FDISK menu, perform Check 4. If drive
C is not listed as active, return to the FDISK menu and choose the option
to set the active partition for drive C. Then restart the computer. If the
problem persists, perform Check 4.
Enter DIR C: and press the Enter key. If the following message is
displayed, go to Procedure 3. If contents of drive C are listed on the
display, perform Check 5.
Invalid media type reading drive C
Abort, Retry, Fail?
Check 5
Use the SYS command in the DOS system to install system files.
If the following message appears on the display, the system files have been
transferred to the HDD. Restart the computer. If the problem persists, go
to Procedure 3.
System transferred
NOTE: If the computer is running Windows 7 Home edition and the hard disk capacity is
more than 512 MB, the FDISK program will ask if you need support for a partition larger
than 2 GB. Select Y for large partition support; however, be sure to read the precaution
regarding access by other operating systems.
Procedure 3 Format Check
The 2.5-inch HDD is formatted using the low-level format program and the FREE-DOS
FORMAT program. Using these programs, follow the steps below to format the HDD.
Check 1
Enter FORMAT C:/S/U to format the HDD and transfer system files. If
the following message appears on the display, the HDD has been formatted.
Format complete
If you cannot format the HDD using the test program, go to Procedure 4.
2-12
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2.5 HDD
2 Troubleshooting
Procedure 4 Test Program Check
Run the HDD test program stored on the maintenance test program disk for all test items.
See Chapter 3 for details on how to use the test program.
If an error is detected during the HDD test, an error code and status will be displayed. The
error codes and their status names are listed in Table 2-1. If an error code is not generated
and the problem still exists, go to Procedure 5.
Table 2- 1 HDD Error Code and Status
Code
Status
1
2
3
4
5
6
Get Parameter Fail !
Read Old Data Error
Write Pattern Error
Read Back Data Error
Data Compare Error
Restore Data Error
7
Read Verify Error
Seek Error
9
10
11
12
13
14
15
16
Disk Controller Self Test Failed
Disk Controller Test unexpected interrupt Failed
Disk Controller action Test Failed
Disk dos not support SMART
Disk read attribute threshold error
Disk read attribute value error
Disk SMART attribute value error
Satellite/E200/E205 Maintenance Manual
2-13
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting
2.5 HDD
Procedure 5 Connector Check and Replacement Check
The HDD or system board may be faulty. Disassemble the computer following the steps
described in Chapter 4 and perform the following checks:
Check 1
Make sure the following connectors have been firmly connected to the
HDD, system board and CPU.
System board
CPU
HDD
If any connector is loose or off, reconnect it firmly and return to Procedure 1.
If there is still an error, perform Check 2.
Check 2
Check 3
Check 4
The HDD may be damaged. Replace it with a new one following the
disassembling instructions in Chapter 4. If the problem persists, perform
Check 3.
The System board may be damaged. Replace it with a new one following
the disassembling instructions in Chapter 4. If the problem persists,
perform Check 4.
The CPU may be damaged. Replace it with a new one following the
disassembling instructions in Chapter 4.
2-14
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2.6 Keyboard
2 Troubleshooting
2.6 Keyboard
To check if the computer’s keyboard is defective or malfunctioning, follow the
troubleshooting procedures below as instructed.
Procedure 1 Test Program Check
Procedure 2 Connector Check and Replacement Check
Procedure 1 Test Program Check
Execute the Keyboard test available as part of the maintenance test program. See Chapter 3
for information on how to perform the test.
If an error is detected in the test, go to Procedure 2. If no error is detected, the keyboard
itself is normal.
Procedure 2 Connector Check and Replacement Check
The keyboard or system board may be disconnected or faulty. Disassemble the computer
following the steps described in Chapter 4 and perform the following checks:
Check 1
Make sure the keyboard cable has been firmly connected to the system
board.
Keyboard
System board
CPU
If the cable is loose or off, reconnect it firmly and return to Procedure 1.
If there is still an error, perform Check 2.
Check 2
Check 3
Check 4
The keyboard may be faulty. Replace it with a new one following the
instructions in Chapter 4. If the problem persists, perform Check 3.
The System board may be faulty. Replace it with a new one following the
instructions in Chapter 4. If the keyboard is still not functioning properly,
perform Check 4.
The memory may be defective. Replace the memory module with a new
one following the steps described in Chapter 4. If the problem persist,
perform Check 5.
Check 5
The CPU may be faulty. Disassemble the computer following the steps
described in Chapter 4 and replace the CPU with a new one.
Satellite/E200/E205 Maintenance Manual
2-15
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting
2.8 Display
2.7 Display
To check if the computer’s display is defective or malfunctioning, follow the troubleshooting
procedures below as instructed.
Procedure 1 External Monitor Check
Procedure 2 Test Program Check
Procedure 3 Connector Check and Replacement Check
Procedure 1 External Monitor Check
Connect an external monitor to the computer's external monitor port, then boot the computer.
The computer automatically detects the external monitor even if resume mode is enabled.
If the external monitor works correctly, the internal LCD, LCD/FL cable, or FL may be
faulty. Go to Procedure 3.
If the external monitor appears to have the same problem as the internal monitor, the system
board may be faulty. Go to Procedure 2.
Procedure 2 Test Program Check
Insert the diagnostics bootable CD in the computer's CD ROM, turn on the computer and run
the test. See Chapter 3 for information on how to perform the test.
If an error is detected in the test, go to Procedure 3. If no error is detected, the display itself
is normal.
Procedure 3 Connector Check and Replacement Check
The display unit has an LCD module, Fluorescent lamp (FL), panel close switch and FL
inverter board. Any of the components or their connections may be defective. Disassemble
the computer following the steps described in Chapter 4, then perform the following checks:
(1)
(2)
(3)
If the FL does not light, perform Check 1.
If characters or graphics are not displayed normally, perform Check 5.
If the FL remains lit when the display is closed, the panel close switch may be
defective. Perform Check 8.
Check 1
Make sure the following cables have been firmly connected to the system
board and FL inverter board.
FL
FL inverter board
System board
CPU
HV cable
LCD/FL cable
If any of the cables is loose or off, reconnect it firmly and return to
Procedure 3. If there is still an error, perform Check 2.
Check 2
The LCD/FL cable may be faulty. Replace it with a new one and return to
Procedure 3. If there is still an error, perform Check 3.
2-16
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2.8 Display
2 Troubleshooting
Check 3
Check 4
Check 5
The FL may be faulty. Replace it with a new one and return to Procedure
3. If there is still an error, perform Check 4.
The FL inverter board may be faulty. Replace it with a new one and
return to Procedure 3. If there is still an error, perform Check 5.
Make sure the LCD/FL cable has been firmly connected to the system
board and LCD module.
FL inverter board
System board
CPU
LCD/FL cable
If the cable is loose or off, reconnect it firmly and return to Procedure 3.
If there is still an error, perform Check 6.
Check 6
Check 7
Check 8
Check 9
The LCD/FL inverter cable may be faulty. Replace it with a new one and
return to Procedure 3. If there is still an error, perform Check 7.
The LCD module may be faulty. Replace it with a new one and return to
Procedure 3. If there is still an error, perform Check 8.
The System board may be faulty. Replace it with a new one. If there is
still an error, perform Check 9.
The memory may be defective. Replace the memory module with a new
one following the steps described in Chapter 4. If the problem persists,
perform Check 10.
Check 10
The CPU may be faulty. Replace it with a new one following the
instructions in Chapter 4.
Satellite/E200/E205 Maintenance Manual
2-17
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting
2.9 ODD (Optical Disk Drive)
2.8 ODD (Optical Disk Drive)
To check if the internal ODD drive is defective or malfunctioning, follow the troubleshooting
procedures below as instructed.
Procedure 1 ODD Cleaning Check
Procedure 2 Test Program Check
Procedure 3 Connector Check and Replacement Check
Procedure 1 ODD Cleaning Check
1. Turn off the power to the computer.
2. Open the ODD tray by inserting a slender object such as a straightened paper clip into
the eject hole. The object must be long enough to activate the eject mechanism.
3. Clean the laser pickup lens with a lens cleaner. Apply the cleaner to a cloth and wipe
the lens.
4. If the ODD drive still does not function properly after cleaning, go to Procedure 2.
Procedure 2 Test Program Check
Execute the ODD drive test program available as part of the maintenance test program. Insert
the diagnostics CD in the computer's CD, turn on the computer and run the test. Then insert a
test ODD (Toshiba-EMI DVD-ROM TEST DISK TSD-1) into the ODD drive. See Chapter 3
for information on how to perform the test.
If any error is detected by the test, go to Procedure 3.
Procedure 3 Connector Check and Replacement Check
The ODD drive is connected to the system board by the connector. The connector may be
disconnected from the system board or faulty. Disassemble the computer following the steps
described in Chapter 4 and perform the following checks:
Check 1
Make sure the following connector has been firmly connected to the ODD
drive and the system board.
ODD
drive
System board
CPU
Attachment case
Connector
If the connector is loose or off, reconnect it firmly and return to Procedure 2.
If there is still an error, perform Check 2.
Check 2
The connector may be faulty. Replace the connector with a new one
following the steps in Chapter 4. If the ODD drive is still not functioning
properly, perform Check 3.
2-18
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2.10 LAN
Check 3
Check 4
Check 5
2 Troubleshooting
The ODD drive may be faulty. Replace the ODD drive with a new one
following the steps in Chapter 4. If the ODD drive is still not functioning
properly, perform Check 4.
The system board may be faulty. Replace it with new one following the
instructions in Chapter 4. If the ODD drive is still not functioning
properly, perform Check 5.
The memory may be defective. Replace the memory module with a new
one following the steps described in Chapter 4.
Satellite/E200/E205 Maintenance Manual
2-19
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting
2.9 ODD (Optical Disk Drive)
2.9 LAN
To check if the computer’s LAN is defective or malfunctioning, follow the troubleshooting
procedures below as instructed.
Procedure 1 Test Program Check
Procedure 2 Connector Check and Replacement Check
Procedure 1 Test Program Check
Execute the LAN check program available as part of the maintenance test program. This
program will check the LAN. Insert the Bootable CD into the CD. Turn on the computer
and run the check program. See Chapter 3 for information on how to perform the check.
If any abnormal is detected by the check, go to Procedure 2
Procedure 2 Connector Check and Replacement Check
The LAN connector (RJ45) is mounted on the system board. If the LAN malfunctions, the
system board or CPU might be faulty.
Disassemble the computer following the steps described in Chapter 4 and perform the
following checks:
Check 1
Check 2
Check 3
The system board may be faulty. Replace it with a new one following the
instructions in Chapter 4. If the LAN is still not functioning properly,
perform Check 2.
The memory may be defective. Replace the memory module with a new
one following the steps described in Chapter 4. If the problem persists,
perform Check 3.
The CPU may be faulty. Disassemble the computer following the steps
described in Chapter 4 and replace the CPU with a new one.
2-20
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Finger Print (Optional)2.10 Audio Test
2 Troubleshooting
2.10 Finger Print (Optional)
To check if the computer’s Finger Print is defective or malfunctioning, follow the
troubleshooting procedures below as instructed.
Procedure 1 Test Program Check
Procedure 2 Connector Check
Procedure 1 Test Program Check
Execute the Finger Print test program available as part of the maintenance test program. This
program checks the Finger Print. Insert the Bootable CD into the CD. Turn on the computer
and run the test. See Chapter 3 for information on how to perform the test.
If any error is detected by the test, go to Procedure 2
Procedure 2 Connector Check
The Finger Print connector is mounted on the system board. If the Finger Print malfunctions,
the system board or Finger Print Board might be faulty.
Disassemble the computer following the steps described in Chapter 4 and perform the
following checks:
Check 1
The Finger Print board may be faulty. Replace it with a new one
following the instructions in Chapter 4. Then go through procedure 1
again. If the Finger Print is still not functioning properly, perform Check
2.
Check 2
The system board may be defective. Replace the system board with a new
one following the steps described in Chapter 4. Then go through
procedure 1 again.
Satellite/E200/E205 Maintenance Manual
2-21
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting
2.10 Finger Print
2.11 Audio Test
To check if the computer’s Speaker is defective or malfunctioning, follow the
troubleshooting procedures below as instructed.
Procedure 1 Test Program Check
Procedure 2 Connector Check and Replacement Check
Procedure 1 Test Program Check
Execute the Audio test available as part of the maintenance test program. See Chapter 3 for
information on how to perform the test.
If an error is detected in the test, go to Procedure 2. If no error is detected, the Audio itself is
normal.
Procedure 2 Connector Check and Replacement Check
The Audio or system board may be disconnected or faulty. Disassemble the computer
following the steps described in Chapter 4 and perform the following checks:
Check 1
Make sure the Speaker cable has been firmly connected to the system
board.
Speaker
System board
CPU
If the cable is loose or off, reconnect it firmly and return to Procedure 1.
If there is still an error, perform Check 2.
Check 2
Check 3
Check 4
The Speaker may be faulty. Replace it with a new one following the
instructions in Chapter 4. If the problem persists, perform Check 3.
The System board may be faulty. Replace it with a new one following the
instructions in Chapter 4. If the Audio is still not functioning properly,
perform Check 4.
The memory may be defective. Replace the memory module with a new
one following the steps described in Chapter 4. If the problem persist,
perform Check 5.
Check 5
The CPU may be faulty. Disassemble the computer following the steps
described in Chapter 4 and replace the CPU with a new one.
2-22
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2.12 IEEE 1394 Test
2 Troubleshooting
2.12 IEEE 1394 Test
To check if the computer’s IEEE 1394 is defective or malfunctioning, follow the
troubleshooting procedures below as instructed.
Procedure 1 Test Program Check
Procedure 2 Connector Check
Procedure 1 Test Program Check
Execute the IEEE 1394 test program available as part of the maintenance test program. This
program checks the IEEE 1394. Insert the Bootable CD into the CD. Turn on the computer
and run the test. See Chapter 3 for information on how to perform the test.
If any error is detected by the test, go to Procedure 2
Procedure 2 Connector Check
The IEEE 1394 connector is mounted on the system board. If the IEEE 1394 malfunctions,
the system board or CPU might be faulty.
Disassemble the computer following the steps described in Chapter 4 and perform the
following checks:
Check 1
Check 2
Check 3
The system board may be faulty. Replace it with a new one following the
instructions in Chapter 4. If the IEEE 1394 is still not functioning
properly, perform Check 2.
The memory may be defective. Replace the memory module with a new
one following the steps described in Chapter 4. If the problem persists,
perform Check 3.
The CPU may be faulty. Disassemble the computer following the steps
described in Chapter 4 and replace the CPU with a new one.
Satellite/E200/E205 Maintenance Manual
2-23
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting
2.13 Cooling Module
2.13 Cooling Module
To check if the computer’s cooling module is defective or malfunctioning, follow the
troubleshooting procedures below as instructed.
Procedure 1 Test Program Check
Procedure 2 Connector Check and Replacement Check
Procedure 1 Test Program Check
Execute the Fan On/off test program available as part of the maintenance test program. This
test program checks the cooling module. Insert the diagnostics bootable CD in the
computer's CD, turn on the computer and run the test. See Chapter 3 for information on how
to perform the test.
If any error is detected by the test, go to Procedure 2.
Procedure 2 Connector Check and Replacement Check
The cooling module is connected to the system board. If the cooling module malfunctions,
there may be a bad connection between the cooling module and the system board or either
might be faulty.
Disassemble the computer following the steps described in Chapter 4 and perform the
following checks:
Check 1
Make sure the cooling module has been firmly connected to the connector
on the system board. Also make sure that the tape is not stuck to any part
of the fan and that the fan is free of foreign matter.
System board
Cooling module
CPU
If the connector is disconnected, connect it firmly to the system board and
return to Procedure 1. If the tape is stuck to any part of the fan, stick it back
to the specified point. If a foreign matter is found in the fan, remove it and
then return to Procedure 1. If there is still an error, perform Check 2.
The cooling module may be faulty. Replace it with a new one following the
steps in Chapter 4. If the cooling module is still not functioning properly,
perform Check 3.
Check 2
Check 3
The memory may be defective. Replace the memory module with a new
one following the steps described in Chapter 4. If the problem persists,
perform Check 4.
Check 4
The CPU may be faulty. Disassemble the computer following the steps
described in Chapter 4 and replace the CPU with a new one.
2-24
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2.13 Cooling Module
2 Troubleshooting
Satellite/E200/E205 Maintenance Manual
2-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Diagnostic Programs
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Diagnostic Programs
Chapter 3 Contents
General.......................................................................................................................... 1
Audio Play Test....................................................................................... 9
DMI Read................................................................................................ 9
DMI Write............................................................................................. 10
3.2.10 System Information............................................................................... 17
3.2.11 View Logs ............................................................................................. 18
3.2.12 Exit to Free DOS.................................................................................. 19
Display LOG File.................................................................................. 29
LOG Viewer.......................................................................................... 30
3.3.10 LOG File Sample................................................................................... 31
System Test................................................................................................................. 36
Memory Test............................................................................................................... 41
ii
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Diagnostic Programs
3.10 Peripheral.................................................................................................................... 60
3.11 Error Codes and description........................................................................................ 64
3.12 Quick Test Item List ...................................................................................................... i
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
3.1 General
3 Diagnostic Programs
3.1 General
This chapter explains the diagnostic programs which tests and diagnoses the functions of the
hardware components of this computer. The diagnostic programs can be classified into two
types: OPTION and DIAGNOSTIC TEST.
NOTE 1: This Diagnostic supports MainZ 10
NOTE 2: Before test must set SATA Controller Mode to “Compatibility” in BIOS
Advanced setting, when finished test set it to “AHCI”
NOTE 3: Before running a test, be sure to:
1. Check that all the cables are connected securely.
2. Exit the application that is currently running and close Windows.
The OPTION includes the following functions:
Select All Items
Test All Items
Edit Batch Parameters
Load Batch Parameters
Save Batch Parameters
Log Parameters
Specify Log Viewer
Display Error Log File
DOS Shell
Exit to Free-DOS
The DIAGNOSTIC TEST Devices include the following tests:
System Test
Memory Test
Storage Test
Video Test
Communication Test
Peripheral Test
Keyboard Layout Test
Hot Key Test
Audio Play Test
Audio Record Test
3D Sensor Test
DMI Read
DMI Write
System Information
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 1
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Diagnostic Programs
3.1 General
Before running the diagnostic programs, get the following tools prepared:
A Service Diagnostic BOOT CD or USB Flash Memory
A Formatted FLOPPY DISK
A Test Media CD (A-BEX TEST CD-ROM TCDR-702)(for CD-ROM test)
A Test Media DVD (Toshiba-EMI DVD-ROM TEST DISK TSD-1)
An External Monitor (for DISPLAY test)
A CD-ROM Driver (for CD-ROM test)
Audio Line for audio record test
A Data CD (for CD-ROM test)
The following chapters describe all the test details. The test items could be selected from the
DIAGNOSTIC TEST menu.
Note:
When booting up the unit for the first time, the system will automatically select the location
of the result log file. If a USB floppy drive is connected, and there is an unprotected floppy
diskette with more then 50KB spare space in the drive, system will save all log files into the
root directory the diskette; otherwise, system will save all log files in the root directory of
RAM disk.
2 Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2 Quick Start
3 Diagnostic Programs
3.2 Quick Start
When the system is booting from Service Diagnostic CD or USB Flash Memory, the following
screen will be displayed:
Please select a test item or select 0 to exit to Free-DOS:
3.2.1 Quick Test
When this item is selected, the system will run the configured test items and generate a test
report automatically.
When the test is completed, a file named Quick.log would be saved in the defined location.
When Quick.log is being created, meanwhile, a file named quick.log has already existed, the
system will automatically rename Quick.log to Quick.old for the backup purpose of the log file.
3.2.2 Customization Test
When this item is selected, the system will run the diagnostic programs according to the
procedures you defined. When the test is completed, a file named Custom.log will be saved in
the defined location. Please see the following example-- Mouse test.
1. Use arrow key to select ‘TouchPad’ item on ‘Peripheral’ in the menu, then press Space
key to select it. (When it is being selected, there is a X marked in the [ ])
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 3
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Diagnostic Programs
3.2 Quick Start
Select ‘Test Mouse’ or press F8 to run the test. The prompt information would be
displayed in the screen as below. This test item needs user to verify whether the mouse
works normally.
The test result will be displayed in the following screen:
4 Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2 Quick Start
3 Diagnostic Programs
Here is another method to run the test: Highlight a test item by using arrow keys, then,
press Enter to start. If there are parameters provided, user should set parameters in the
parameter dialog window.
CPU Speed Test (Step by Step):
1. Select test item:
Select System—CPU—CPU Speed, then, press the Enter key.
2. Parameters Setting
Choose the OK button after you set the proper parameters in the following window.
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 5
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Diagnostic Programs
3.2 Quick Start
3. Test Result
System will automatically run and display the test result as follows:
Following is the comparison report of the two testing methods mentioned above:
1) Configuration and Running
As to the method used in Mouse test, the user is required to select test items by pressing
advance; otherwise the default parameters would be used. Using this method, user is
allowed to select more than one test item at one time.
2) Running the current test item
6 Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2 Quick Start
3 Diagnostic Programs
As to the method adopted in CPU Speed test, user should highlight the test item and
press Enter to start testing. And the user has to setup the parameters every time before
running the test. Using this method, only one test item would be tested at one time.
3.2.3 Keyboard Layout test
The test purpose is to check whether 30 kinds of keyboards run well during the test
procedure. When users choose the item, the names of these countries will be displayed on
the screen for user choice. User press any index of token in ASCII, and the program will
test the kind of keymap of the country.
The test screen would be shown as below:
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 7
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Diagnostic Programs
3.2 Quick Start
It requires user to press the key and check whether the key in the screen changes
color or not. User can terminate test by typing ‘END’. When testing the ‘Fn’ key, it
must press the ‘Enter’ key at the same time.
When the user has checked all the keys and all the keys in the screen have changed
color, the diagnostics program would automatically end the test and report the pass
information.
If keyboard test fails, program will terminate the test and report the fail information
when it is time to timeout.
The test will end when all keys are pressed or test time is out after 90 seconds.
3.2.4 Hotkey Test
Check whether Hotkey run well. Hotkey test mainly functional keys, for example: IE
Key Audio play etc. The methods of testing hotkey are different from keyboard tests
sometimes depending on the specific type of notebooks, and this explains why some
types of notebooks can be tested together with keyboard while others cannot. Press E+
+N+D to quit the test.
8 Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2 Quick Start
3 Diagnostic Programs
3.2.5 Audio Play Test
Check whether the system could playback audio normally. When the test is completed, a
file named Audio_P.log will be saved in the defined location.
3.2.6 Audio Record Test
Check whether the system could record the sound normally. If there is no error during
the whole test, Pass; otherwise Fail. The test will repeat for four times. When the test is
completed, a file named autest.log will be saved in the defined location.
3.2.7 DMI Read
Read the information from the system’s SMBIOS and display it in the screen as follows:
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 9
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Diagnostic Programs
3.2 Quick Start
User can press any key to exit the program.
3.2.8 DMI Write
In addition to reading the DMI information, DMI Write also permits attributes editing
and updating: Manufacture, Product Name, Version, Serial Number, and OEM Part
Number, etc. The following screen will be displayed:
In this screen, there are two lines which attribute could be edited and updated. The 1st
line (the font in yellow with blue background) shows the attribute’s value that is read
from the current system and the 2nd line (the font in red with turquoise background)
shows the same value as that in the 1st line before user’s editing. User can modify the
10 Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2 Quick Start
3 Diagnostic Programs
attribute’s value in the 2nd line and press Enter to confirm the current edition and
continue editing the next attribute.
During the editing, user could press F2 to confirm the DMI attribute update or press F4
to ignore the modification. Press ESC to exit the program of DMI Write.
The confirmation screen is as below:
The attributes that have been modified would be marked in red; otherwise in yellow.
User could press F2 to save the changes, or press F4 to ignore and exit the current
program.
3.2.9 3D Sensor Test
In 3D Sensor test, the system checks whether the HDD protection is normal. This
program judges by sampling five kinds of data shown below.
No Item
Contents
1
2
Access
platform.
An access platform is leveling.
Test
The Fixture which fixes PC by 90 degree inclination is used.
Fixture
Vibration/shock doesn't take a PCB at the time of T&D inspection.
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 11
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Diagnostic Programs
3.2 Quick Start
3
Test1
The display of a test program and the set method of PC are shown below.
Display of a Test Program
The portion which PC and Test-Fixture contact is green.
Set method of PC
Z
Upper
X
Judgment
If all data is less than ranges, it will be OK.
12 Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2 Quick Start
3 Diagnostic Programs
4
Test2
The display of a test program and the set method of PC are shown below.
Display of a Test Program
Set method of PC
Rear
Upper
Judgment
If all data is less than ranges, it will be OK.
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 13
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Diagnostic Programs
3.2 Quick Start
5
Test3
The display of a test program and the set method of PC are shown below.
Display of a Test Program
Set method of PC
Right
Upper
Judgment
If all data is less than ranges, it will be OK.
14 Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2 Quick Start
3 Diagnostic Programs
6
Test4
The display of a test program and the set method of PC are shown below.
Display of a Test Program
Set method of PC
Front
Upper
Judgment
If all data is less than ranges, it will be OK.
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 15
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Diagnostic Programs
3.2 Quick Start
7
Test5
The display of a test program and the set method of PC are shown below.
Display of a Test Program
Left
Set method of PC
Upper
Judgment
If all data is less than ranges, it will be OK.
Judgment
8
9
Inspection
If all data is less than ranges, it will be OK.
When an inspection result is O.K., calibration at HPC.
Setting
Calibration
data
If it succeeded, the system will prompt a message of PASS, otherwise the message will
be FAIL.The test information will be written in log file.
Note:
Please do not use this program, when you test PC without 3D sensor.
16 Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2 Quick Start
3 Diagnostic Programs
3.2.10 System Information
This function is used to read the system information. When the test is completed, a file
named System.log will be saved in the defined location. During the reading process, the
following screen will be displayed to indicate that the progress is in detection:
On the left column of the above screen, the detected hardware components are listed. The
corresponding information of the detected hardware components is displayed on the right
of the screen. It displays the current running status information of the check program.
The name of the program is marked on the top of the screen. At the bottom, the function
keys are listed for user operation. During the detection, keyboard operation is invalid.
When the detection is finished, the hardware components information will be displayed
as follows:
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 17
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Diagnostic Programs
3.2 Quick Start
User can use function keys listed on the bottom of the screen to display the configuration
of the component or exit the current program. On the left column, the components
information is listed and user can use arrow keys or PgUp/PgDn to view the list and
highlight the chosen component. On the right column, the configuration information of
the highlighted component is listed. Press ESC to exit this program.
3.2.11 View Logs
User can enter one choice to view a log file in the screen as follows.
18 Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2 Quick Start
3 Diagnostic Programs
3.2.12 Exit to Free DOS
Select this item to exit to Free DOS.
3.2.13 The Diagnostics Screen Explanation
Below is an example of running a test item. It includes the following parts: Diagnostics
Windows, Test Status Area, Progress Bar, Error List, Test Item’s Title, Status Bar and
Message Box.
1. Diagnostics Windows
When a test item is running, a Diagnostics Windows is displayed in full screen. It consists of
the following parts: Title Bar, Test Running Status and Report Panel, Status Bar. There
would prompt a message box called USER BREAK in the central of the window whether
user press ESC to interrupt the test.
2. Test Running Status and Report Panel
Test Running Status and Report Panel are located on the middle of Diagnostics Windows.
Test item name, test process and test result are displayed in the left;
Test status and result are displayed in the upper right corner of the screen. It displays the
test status of the current test item – TEST (in testing), PASS (test finished and its result
is passed), FAIL (test finished and its result is failed) and SKIP (test skipped).
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 19
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Diagnostic Programs
3.2 Quick Start
The error list of each test module is displayed at the lower right corner of the screen. It
would display the total error quantity found in the test, the most recent five error codes
and description would be shown here. Detailed error report could be viewed with
Logview.exe.
When pressing ESC key during the test process, a User Break Windows will be popped
up for the user to select.
3. USER BREAK
Pressing ESC key to interrupt the test, USER BREAK message box would be prompted out
in the central of Diagnostics Window for the user to select the following actions:
CONTINUE---- Continue the test;
SKIP---- Stop the sub-item of current test item to go to the next item’s test;
ABORT----Stop the current test item to test the next module.
ABORT ALL---- Stop all the selected test items. User could use the hot key Ctrl+D to
achieve the same operation. When the user calls ABORT ALL, the following message
box will prompt for his selecting.
4. Title Bar:
Title Bar located at the top of the window, it includes information as follows:
Program Name and Its Version: Service Diagnostic Ver1.10;
Test Module Name: Label the name and version of the test module. For example, in the
above screen, the name of the test module is ‘Memory Tester Build Date 2007.02.09’.
Status Bar: Located at the bottom of the screen as follows:
The status bar is used to indicate the current script setting and test status. It consists of two
lines that includes the information as follows:
Test Mode: TIMEBOUND or LOOPBOUND, e.g. LOOPBOUND in the above screen;
20 Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2 Quick Start
3 Diagnostic Programs
Script File Name: Script file name, e.g. ‘Custom.INI’ in the above screen;
Current Time(C. TIME): Current system time, e.g. ‘C.TIME:2008-02-16 00:42:40’ in
the above screen;
Test Time Remaining (LEFT): In TIMEBOUND mode, it would display the remaining
test time at the same location as Current TIME (C. TIME) in the above screen;
Current Loop Count: In LOOPBOUND mode, it will display the total LOOP number
planning to execute and the current LOOP number have been finished, e.g. ‘COUNT:
01/01’ in the above screen;
CPU Temperature: Detect the temperature in the current CPU, e.g. ‘CPU: 56C’ in the
above screen;
Remaining Battery Capacity: Remaining Battery Capacity detected in the current
Battery, e.g. ‘BAT: 46%’;
Test Order: Define the test sequence. There is two sequence modes: Sequential Test
Mode and Random Test Mode. The default mode is Sequential Test Mode, it would
displays ‘ORDER: SEQ’ as in the above screen;
LOG File Name: Display the file name of the test log, e.g. Custom.Log in the above
screen;
Start Test Time (S.TIME): Display the test start time for the current test item or the test
script, e.g. ‘S.TIME: 2008-02-16 00:42:28’ in the above screen;
Break On Error: Display ‘HALT’ as shown in the above screen when ‘Break On Error’
is enabled;
Wait On Error: Display ‘WAIT’ as shown in the above screen when ‘Wait On Error’ is
enabled;
Pause Enable: Display ‘PAUSE’ when “Pause Enable” is enabled;
Manual Interrupt Method: Display ‘Esc: Break’ to tell the user how to manually
interrupt the test process.
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 21
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Diagnostic Programs
3.3Option
3.3 Options
3.3.1 Overview
In Service Diagnostics, with the Options menu user can configure the batch
parameters, test item’s parameters and those parameters created by the LOG file.
Options Menu Notes:
Select All/None Items
Switch between selecting all test items and selecting none. The hot key is F6.
Test Selected Items
Execute all selected test items in this editor. The hot key is F8.
If “Interactive” option in batch parameters has not been selected, a warning
message would be shown as below:
Edit Batch Parameters
22 Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3 Option
3 Diagnostic Programs
Configure batch parameters and all the test item’s parameters.
Load Batch Parameters
Upload all the test items and the parameters to the *.ini file.
Save Batch Parameters
Save all the parameters and the test items that are configured in the editor to a
specified file.
Log Parameters
Configure LOG parameters.
Specify LOG Viewer
Specify the viewer for the LOG file.
Display Error Log File
Load the LOG file viewer specified in the Specify Log Viewer to view the LOG
file.
DOS Shell
Enter the DOS Shell and execute the DOS programs. You can also exit to the
Service Diagnostics Editor by the command of EXIT.
Exit to DOS
Exit the Service Diagnostics Editor and back to DOS.
3.3.2 Batch Parameters Configuration
The batch parameters configuration screen can be accessed through Service
Diagnostics/OPTIONS -> EDIT BATCH PARAMETERS -> BATCH
PARAMETERS:
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 23
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Diagnostic Programs
3.3Option
Test Order
Specify the order of the test items. Choose 'Sequence' to adopt the sequential
mode; choose 'Random' to run the test items in random sequence.
Test Options
Choose one of the following options:
Wait On Error
Wait for further confirmation while an error occurs.
Break On Error
Stop the test when a test item fails.
Pause Enable
Pause at the end of each test items and wait for the user to response with the test
items that requires the user to assist the test processes, such as the keystroke test.
Interactive
If the item is enabled during the test, the test items that need user to response can
run normally, such as Mouse test; If it is disabled, those test items will report
FAIL.
When the option here is enabled, it would affect all the test items while the same
option in “Item Parameters Configuration” only affect that test item.
Monitor Battery Life
24 Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3 Option
3 Diagnostic Programs
Monitor the remaining battery capacity (percent).
Monitor CPU Thermal
Monitor the CPU temperature.
Test Mode
LOOPBOUND
The chosen test items will run repeatedly according to the times specified in the
'Number of Loops'.
TIMEBOUND
The chosen test items will run for an extent time specified in 'Time Limit Hrs' and
'Time Limit Min'.
Time Limit Hrs
Specify the hours whether 'TIMEBOUND' is chosen under the batch mode.
Time Limit Min
Specify the minutes whether 'TIMEBOUND' is chosen under the batch mode.
Number Of Loops
Specify the repeating times when 'Loop Bound' is chosen under the batch mode.
3.3.3 Item’s Parameters Configuration
The test items’ parameters configuration screen can be accessed through Service
Diagnostics/Options -> Edit Batch Parameters -> Item’s Parameters-> System-
>CPU-> Basic Functionality:
Repeat count
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 25
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Diagnostic Programs
3.3Option
Repeat times of the test item.
Interactive
If the item is enabled during the test, the test items that need user to response can
run normally, such as PS2 Mouse test; If it is disabled, those test items will
report FAIL.
Whether the option here is enabled, it only affects the current test item.
Parameters
For the test items with specific parameters, this option will call the related
configuration screens. Otherwise, the program will show the following dialogue
window:
Parameters for the specific test items:
Some test items (Memory, HDD, e g...) have their individual parameters, which
can be configured in their parameters setting window.
3.3.4 Load Batch Parameters
Batch parameter is saved in the script file whose extension name is INI (*.INI).
Below is the screen shot of “Load Batch Parameters”.
26 Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3 Option
3 Diagnostic Programs
In this window, you can specify the .INI files that you wanted to be edited or
modified.
3.3.5 Save Batch Parameters
Here you can save the edited or modified content to the batch parameters files.
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 27
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Diagnostic Programs
3.3Option
3.3.6 LOG Parameters Setting
You can access the Log Parameters screen through Service Diagnostics\Options -
Generate Report.
Report Destination
If selecting 'NONE', no log file will be generated; if selecting 'FILE', a log file with
the name specified in 'Log File Name' will be generated.
Log Options
Log Errors
If selecting this parameter, errors will be recorded when the test fails.
Log Test Activities
If selecting this parameter, the subtest results will be recorded.
Log Test Start Time
If selecting this parameter, the start time of the test will be recorded.
Log Test End Time
If selecting this parameter, the end time of the test will be recorded.
Log Errors Only
If selecting this parameter, errors will be recorded only when the test fails.
Log Errors Only with Time
28 Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3 Option
3 Diagnostic Programs
If selecting this parameter, errors and time will be recorded only when the test
fails.
Append to Old Log File
If selecting this parameter, the new log will be added to the old one.
Log Device Info on Fail
If selecting this parameter, details of the failed test will be recorded.
Log file Name
Specify the Log file name. You can input the detail path of the file. System will
show the detail path of the file.
3.3.7 Specify LOG Viewer
You can specify the Log file viewer in the Specify Log Viewer screen.
The default viewing program of Service Diagnostics is LogView.exe.
3.3.8 Display LOG File
You can specify the Log file for viewing in the Display Error Log File screen.
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 29
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Diagnostic Programs
3.3Option
In this screen, you can specify a Log file and view it with the viewer designated in
Specify LOG Viewer.
3.3.9 LOG Viewer
Service Diagnostic Log viewer:
↑, ↓
Scroll a line backward or forward on the screen.
Page Up, Page Down
30 Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3 Option
3 Diagnostic Programs
Scroll a page backward or forward on the screen.
Exit the Log viewer.
Esc
F1
Display the Help information about the Log viewer operations and the
functional keys.
Ctrl+Home
Go to the start of the log file.
Ctrl+End
Go to the end of the log file.
Ctrl+F3
Prompt the search dialogue for the user to input the string to be looked for
and specify the searching method.
F3
Find the next corresponding strings given.
3.3.10 LOG File Sample
Log file is a test result file, which records the following information: Test module name,
Test item name, Start/End time and the test result (including PASS, FAIL, SKIP and
ABORT). When a failure is found, both the error code and the error information were
recorded.
In the Log file, we use Test Items as the test item name, which could not be modified in
the whole time. And we use the Internal Name as name in the program’s UI, which
corresponds to the test item name and could be modified according to the user’s favorite.
The following section is a sample of log file:
DIAG REPORT
<Module Name>: Service Diagnostic Ver 1.00 ... Memory Tester Build Date 2006.01.10
[Walk High]
Begin Time: Wed Jul 05 10:45:36 2006
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 31
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Diagnostic Programs
3.3Option
Base Memory Test
: PASS
: PASS
Extended Memory Test
End Time: Wed Jul 05 10:47:51 2006
<Module Name>: Service Diagnostic Ver 1.00 ... Mouse Test Build Date 2006.01.10
[MSTPad]
Begin Time: Wed Jul 05 10:48:54 2006
Touch Pad Test
: FAIL
ITEM TEST FAIL
Function ID :502
Error Code :50202
Error Message :Touch Pad Test Fail
End Time: Wed Jul 05 10:49:16 2006
32 Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3.4 Subtests
3 Diagnostic Programs
3.4 Subtests
Sub
Test
Test
ID
Item
Subtest
Test items
Internal Name
Group
ID
System
01 CPU
01 Basic Functionality Test
02 CPU Speed
[CPUBasicFun]
[CPUSpeed]
Coprocessor
03
Coprocessor
[NPUFun]
NPU Basic Functions
04 CPU Information
[CPUInformation]
[Protect]
05 CPU Protected Mode
MMX
[MMX]
06
02 Board
01 DMA Controller
02 Interval Timer
03 Clock / Calendar
04 PCI System
[DMACtrl]
[Timer]
[RealClock]
[PCI]
05 Plug and Play
06 ACPI Test
[PnP]
[ACPI]
03 FAN
01 CPU Fan Speed Test
[FANSpeed]
[BIOSROM]
[Parity]
Memory
01 BIOS ROM
02
Parity
03 Pattern
01 Bit Stuck High Test
02 Bit Stuck Low Test
03 Checker Board Test
04 CAS Line Test
[BSHigh]
[BSLow]
[ChkBd]
[CASLine]
[Incrment]
[Decrment]
[Idcrment]
[XWRCycle]
[XRCycle]
[WalkHigh]
[WalkLow]
[Address]
[Refresh]
[CacheOne]
[Random]
05 Incremental Test
06 Decremental Test
07 Incremental Decremental Test
04 Extended Pattern 01 Write/Read Cycle Test
02 Read Cycle Test
05 Walking 1's Test
06 Walking 0's Test
07 Memory Address
08 Refresh Test
09 Cache Memory
10 Random Memory 01 Randomize Test
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 33
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Diagnostic Programs
3.4 Subtests
02 Random Increment Read/Write [RandIncr]
11 Data Bus Test
[DataBus]
Memory Speed
Test
12
[MemSpeed]
Storage
01 HDD
01 Sequential/Random R/W
02 Sequential/Random Seek
03 Performance
[SeqRdRW1]
[Seek1]
[Perform1]
04 Controller Check
05 Diagnostic Read/Write
06 SMART Test
[Controller1]
[DiagRW1]
[SMART1]
02
01 Controller Test
[CDRWController]
[CDRWTransRate]
[CDRWButterfly]
[CDRWSeek]
[CDRWSFSeek]
[CDRWTray]
[CharTest]
ODD
02 Data Transfer Rate
03 Data CD Butterfly Seek
04 Data CD Random Seek
05 Data CD Sequence Seek
06 Tray Eject Test
Video
01 Text Mode
01 Character Test
02 Text Attribute
[Attribut]
03 Text Page Selection
04 Text Color
[PageSel]
[Color]
05 80*25 Text Mode
[Text Mode]
640*480 VGA
Mode
02
03
[VGAMode]
640X480 Video Modes
VESA 640x480x256 Mode
[V640480_15]
[V640480_16]
[V640480_24]
[V640480_32]
VESA 640x480x32K Mode
VESA 640x480x64K Mode
VESA Video
Modes
01
VESA 640x480x16K Mode
VESA 640x480x32bit Mode
800X600 Video Modes
VESA 800x600x256 Mode
VESA 800x600x64K Mode
[V800600_15]
[V800600_16]
[V800600_24]
[V800600_32]
02
VESA 800x600x32K Mode
VESA 800x600x16K Mode
VESA 800x600x32bit Mode
1024X768 Video Modes
03 VESA 1024x768x256 Mode
VESA 1024x768x64K Mode
[V1024768_15]
[V1024768_16]
[V1024768_24]
34 Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3.4 Subtests
3 Diagnostic Programs
[V1024768_32]
VESA 1024x768x32K Mode
VESA 1024x768x16K Mode
VESA 1024x768x32bit Mode
VESA Video
Memory
04
[VESAMEM]
05 AGP Test
[AGP]
06 LCD Panel Test
07 Register Test
08 Color Purity Test
09 Direct Color Test
[LCDPanel]
[Register]
[ColPurity]
[DirectColor]
DAC/Palette
Address
Bitblt Engine
Test
10
[DACPalAddr]
[Bitblt]
11
COMM
01 LAN Card
01 Device ID Detection
02 Vendor ID Detection
03 Mac Address Detection
01 GUID Detection
01 Keyboard Data Line
02 Keyboard Clock Line
01 TouchPad
[DeviceID]
[VendorID]
[MAC Address]
[1394 R/W Test]
[KBDataLn]
[KBClokLn]
[MSTpad]
02 1394
Peripheral 01 Keyboard
02 Mouse
03 Led
01 Device Led
[KBLED]
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 35
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Diagnostic Programs
3.5 System Test
3.5 System Test
Move arrow keys and press the Space key to select CPU test item from Service
Diagnostic menu, then highlight CPU and press the Enter to run this test item.
Subtest 01 CPU
1. Basic Functionality Test
This test item is to check whether the CPU works normally through math and
logic calculation, which means verifying the general registers, math registers
and logic registers.
2. CPU Speed
This test item is to detect the work frequency of the current CPU. User should
change the parameters setting in the following window before the test:
36 Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3.5 System Test
3 Diagnostic Programs
CPU Speed Comparison--Whether you want to make a comparison of the
CPU speed with the value set in ‘Expected CPU Speed’, you should choose
‘Yes’; otherwise, ‘No’.
Expected CPU Speed--Specify the expected CPU Speed value you want
for further comparison.
Allowable Error Rate-- Specify the Allowable Error Rate value you want
for further comparison.
3. Coprocessor
NPU Basic Functions Test
This test item is to check whether the precision of the numeric processor in
the float calculation is up to the IEEE standards.
NPU Interrupt Test
This test item is to check whether NPU transfers the abnormal Interrupt
program correctly by forcing an abnormal float.
4. CPU Information
This test item is used for getting & showing CPU Information. It will be
displayed as follows:
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 37
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Diagnostic Programs
3.5 System Test
5. CPU Protected Mode Test
This test item is to check whether CPU protected mode instruction works
normally.
6. MMX
The test item is to confirm whether the CPU supports MMX instructions.
Subtest 02 Boards
1. DMA Controller
This test item is to check whether the DMA controller works normally.
2. Interval Timer
This test item is to check whether the Interval Timer (18.2Hz, 55ms) works
normally.
3. Clock/Calendar
This test item is to check whether the system clock/calendar works
normally.
4. PCI System
This test item is to check whether the bus number, device number and
function number in PCI bus are valid.
5. Plug and Play
38 Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3.5 System Test
3 Diagnostic Programs
This test item is to check:
1. Whether the current system supports Plug-n-Play;
2. Whether there is an ESCD (Extended System Configuration Data) in
the BIOS;
3. Whether there is PCI-to-ISA bridge in the system;
4. Whether there is PCI bus in the system.
6. ACPI Test
ACPI test includes two sub-items as below:
System Address Map Test: Check the correctness of ACPI system memory
map, and whether its mapping scope is within real memory.
ACPI Table Test: Check the correctness of ACPI relative configuration
tables in the current system.
Subtest 03 FAN Speed Test
1. CPU Fan Speed Test
This test item is to check whether the CPU fan currently used works
normally in the different speeds of stop, slow, middle and fast. Below is the
parameter setting dialog window.
Set the range of Speed that is to be tested, then choose the OK button to
test it. It will be displayed as follows:
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 39
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Diagnostic Programs
3.5 System Test
40 Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3.6 Memory Test
3 Diagnostic Programs
3.6 Memory Test
This test module is to check whether the memory chip works normally.
Subtest 01 BIOS ROM
This test item is to check the validity of BIOS ROM that includes two sub-items --
ROM Read and ROM Write Protection. ROM Read is to check whether BIOS
ROM could be correctly read out, ROM Write Protect is to check whether BIOS
ROM is write-protected.
Subtest 02 Parity
This test item is to check whether the parity checkout error could happen through
writing and reading memory. Below is the parameter setting dialog window.
Test Option: Choose the Memory part to take the test– Base Memory or
Extended Memory.
Extended Memory Test Range: Specify the test coverage range of
Extended Memory. If user chooses Total Size, it means that the whole
Extended Memory will be tested. Although user can input the parameter
into other select box, but the selected result is invalid. If user chooses
Special Size, the test of Extended Memory will be taken according to the
coverage range that user chooses or time.
Extended Memory Start Address (MB) & Extended Memory End
Address (MB): Set the range of extended memory that is to be tested, the
test coverage would be based on the setting and the value in ‘Percent (%)
mentioned at below.
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 41
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Diagnostic Programs
3.6 Memory Test
Pattern Size: Choose the pattern size – BYTE, WORD, DWORD or ALL.
Percent (%): Choose the percentage of the defined range of the memory to
be tested.
Time Limit(h): Choose or Input the time (hour) of the defined range of the
memory to be tested.
Time Limit(m): Choose or Input the time (minute) of the defined range of
the memory to be tested.
Subtest 03 Patterns
This test item is to check whether the system memory includes base memory and
extended memory that could be accessed correctly through writing and reading
with a series of designed pattern data. Below is the parameter setting dialog
window.
Test Option: Choose the Memory part to take the test– Base Memory or
Extended Memory.
Extended Memory Test Range: Specify the test coverage range of
Extended Memory. If user chooses Total Size, it means that the whole
Extended Memory will be tested. Although user can input the parameter
into other select box, but the selected result is invalid. If user chooses
Special Size, the test of Extended Memory will be taken according to the
coverage range that user chooses or time.
Extended Memory Start Address (MB) & Extended Memory End
Address (MB): Set the range of extended memory that is to be tested, the
42 Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3.6 Memory Test
3 Diagnostic Programs
test coverage would be based on the setting and the value in ‘Percent (%)
mentioned at below.
Pattern Size: Choose the pattern size – BYTE, WORD, DWORD or ALL.
Percent (%): Choose the percentage of the defined range of the memory to
be tested.
Time Limit(h): Choose or Input the time (hour) of the defined range of the
memory to be tested.
Time Limit(m): Choose or Input the time (minute) of the defined range of
the memory to be tested.
1. Bit Stuck High Test
Data pattern: Every bit is ‘1’ (Each bit is high)
2. Bit Stuck Low Test
Data pattern: Every bit is ‘0'(Each bit is low);
3. Checker Board Test
Data pattern: Lo-byte and hi-byte are composed with 0101(0x5) and 1010
(0xA);
4. CAS Line Test
Data pattern: Lo-byte and hi-byte are composed with 0000 (0x0) and
1111(0xF);
5. Incremental Test
Data pattern: A series of increasing data from 0 by adding 1 each time;
6. Decrement Test
Data Pattern: A series of decreasing data from the maximum (e.g. 0xFFFF) by
subtracting 1 each time;
7. Incremental / Decrement Test
Data Pattern is a series of data whose low byte is increasing data from 0x00
and high byte is decreasing data from 0xFF.
Subtest 04
Extended Pattern
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 43
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Diagnostic Programs
3.6 Memory Test
In addition to the above pattern test of the memory, there is Read/Write Cycle test
and Read Cycle Test for the extended memory.
Below is the parameter dialog window of the extended pattern test.
Test Range: Specify the test coverage range of Extended Memory. If
user chooses Total Size, it means that the whole Extended Memory
will be tested. Although user can input the parameter into other select
box, but the selected result is invalid. If user chooses Special Size, the
test of Extended Memory will be taken according to the coverage
range that user chooses or time.
Extended Memory Start Address and Extended Memory End
Address (MB): Set the range of extended memory that is to be tested.
The test coverage will be according to the value setting in ‘Percent
(%)’ mentioned at below.
Percent (%): Choose the percentage of the defined range of the
memory to be tested.
Time Limit(h): Choose or Input the time (hour) of the defined range
of the memory to be tested;
Time Limit(m): Choose or Input the time (minute) of the defined
range of the memory to be tested.
1. Write/Read Cycle Test
Test by using both read and write instructions.
2. Read Cycle Test
44 Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3.6 Memory Test
3 Diagnostic Programs
Test by using read instructions.
Subtest 05 Walking 1’s Test
The test item is to ensure that there is no short circuitry issue in memory chip. The
parameter dialog window is the same as that in ‘Subtest 02 Pattern’.
Subtest 06 Walking 0’s Test
The test item is to ensure that there is no open circuitry issue in memory chip. The
parameter dialog window is the same as that in ‘Subtest 02 Pattern’.
Subtest 07 Memory Address
This test item is to check short and open issue on memory address lines.
Subtest 08 Refresh Test
This test item is to check whether the memory refresh works normally. The
parameter dialog window is as follows:
Subtest 09 Cache Memory
The test item is to check whether the CPU internal cache memory could be
accessed correctly.
Subtest 10 Random Memory
Random Memory test includes the following two test items: Randomize Test and
Random Incremental Read/Write Test. The parameter dialog window is the same
as that in ‘Subtest 03 Extended Pattern’.
1. Randomize Test
This test item is to check whether the memory could be correctly accessed
with randomized data and randomized memory address.
2. Random Increment Read/Write
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 45
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Diagnostic Programs
3.6 Memory Test
This test item is to check whether the memory could be correctly accessed
with randomized memory address and a series of incremental data.
Subtest 11 Data Bus Test
This test item is to check whether the data bus works normally.
Subtest 12 Memory Speed Test
This test item is to check the data-transferring rate for the cache memory and the
system memory.
46 Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3.7 Storage
3 Diagnostic Programs
3.7 Storage
Subtest 01 HDD
This test item runs on IDE hard disks. It checks the functions and performance of IDE
hard disk.
In order to protect user’s HDD data, the password must be verified before the
HDD test. The screen is as follows:
Password：hard disk
1. Sequential/Random R/W
This test item is to check the HDD’s Read/Write function through data writing
and reading to HDD.
This test item needs user to submit the parameters:
IDE HDD Test Range-- Specify the test coverage range of IDE HDD. If user
chooses Total Size, it means that the whole IDE HDD will be tested. Although
user can input the parameter into other select box, but the selected result is
invalid. If user chooses Special Size, the test of IDE HDD will be taken
according to the coverage range that user chooses or time.
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 47
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Diagnostic Programs
3.7 Storage
LBA Start, LBA End--Specify the start and end byte in LBA (Large Block
Address).
Percent—Specify the coverage rate in percentage of the total disk.
Time Limit(h): Choose or Input the time (hour) of the defined range of the total
disk to be tested.
Time Limit(m): Choose or Input the time (minute) of the defined range of the
total disk to be tested.
Test Mode—Choose test mode from the following options:
(1) Read & Write –Write data on the disk, then read it out and compare the two
value;
(2) Read Verify —Read data only;
(3) Unprotected Write—Write data on the disk without backup original data.
Option—Select sequential test or random test
2. Sequential/Random Seek
The test item is to check the correctness of the HDD’s sector’s seeking function.
This test item involves the following parameters:
IDE HDD Test Range—is same as the description of the upper item.
LBA Start, LBA End-- specify start and finish byte in LBA(Large Block
Address);
Option-- Select sequential test or random test;
48 Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3.7 Storage
3 Diagnostic Programs
Percent-- Specify the coverage rate in percentage of the total disk.
Time Limit(h): Choose or Input the time (hour) of the defined range of the total
disk to be tested;
Time Limit(m): Choose or Input the time (minute) of the defined range of the
total disk to be tested.
3. Performance
Check the HDD’s seeking speed and transfer the data rate.
4. Controller Check
Check the HDD controller’s status, including HDD interrupt and unexpected
interrupt.
5. Diagnostic Read/Write
This test item is a quick test to verify whether the HDD could be correctly
accessed and the user could specify the percentage in the below dialog.
Percent (1-100)-- Specify the coverage rate in percentage of the total disk.
Time Limit(h): Choose or Input the time (hour) of the defined range of the total
disk to be tested;
Time Limit(m): Choose or Input the time (minute) of the defined range of the
total disk to be tested;
6. SMART Test
SMART stands for Self-Monitoring, Analysis and Reporting Technology.
SMART test will compare the attribute values with the threshold value in the
HDD’s controller to confirm whether there is any failure in the HDD
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 49
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Diagnostic Programs
3.7 Storage
Subtest 02 ODD
The ODD test runs on IDE CDROM/DVD-ROM & CD-RW. It will check the ODD
driver’s functionality and performance.
1. Controller Test
Check the CDROM controller’s status.
2. Data Transfer Rate
Check the data transfer rate of the ODD drive. It will read data from the ODD disc
and calculate the data transfer rate. This test needs a data CD.
3. Data CD Butterfly Seek
Check the seek function of the ODD drive. It will perform a serial of seeking
operations. First, locate the minimum LBA address, then the maximum, the sub-
minimum, the sub-maximum and meet at center point. This test needs a data CD.
4. Data CD Random Seek
Check the random seek function of ODD drive. Random access will reflect the
performance of the heads’ random movement and seek. It tests for 1000 times.
5. Data CD Sequence Seek
Check the sequential seek function of ODD drive. Perform location test to CD-
RW under LBA mode with the location address increasing in sequence.
6. Tray Eject Test
Check the eject function of the ODD. It will eject the ODD and ask the user to
confirm if the operation succeeds.
50 Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3.8 Video
3 Diagnostic Programs
3.8 Video
This test item tests the video by:
1. displaying the figures in different graphic modes.
2. displaying the property and color of the characters in different text modes.
User will confirm whether each video mode works normally by judging whether the display
is correct. It checks whether the video memory works normally by writing data into the video
memory, then reading it out and comparing the two value.
Subtest 01
Text Mode
1. Character Test
Tests two types of font patterns.
Font 9*14
Font 9*16
It requires the user to check whether all characters of each font type displayed
correctly by answering the questions prompted on screen. It will be displayed as
follows:.
2. Text Attribute
This test item is to check whether the text attribute of normal, hi-intensity,
inverse, and blinking in VGA text mode could be correctly displayed on the
screen.
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 51
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Diagnostic Programs
3.8 Video
It would display the below texts of the different attributes in the screen:
1. Text in normal attribute;
2. Text in blinking normal attribute;
3. Text in inverse attribute;
4. Text in blinking inverse attribute;
5. Text in hi-intensity attribute;
6. Text in blinking hi-intensity attribute;
Users need to check whether all texts displayed correctly in the above six
attributes and key in the answer ‘Y’ or ‘N’ to the prompts ‘Is this display OK?
[Y/N<Enter=Y>]’.
Below is the test screen of Text Attribute.
3. Text Page Selection
This test item is to check whether the video memory could be correctly written
and read in VGA text mode. According to the comparison of written data with
read data, the program would report PASS or FAIL.
52 Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3.8 Video
3 Diagnostic Programs
4. Text Color
This test item is to check whether all 16 colors foreground and all 8 colors
background works normally in VGA text mode.
The bit4-6 of the attribute byte of a character defines 8 background colors (black,
blue, green, cyan, red, brown, magenta, and light gray), and the bit0-3 defines 16
foreground colors (dark gray, light blue, light green, light cyan, light red, light
magenta, yellow, and white besides the above 8 colors).
In the test, user is required to respond according to the instruction in the screen.
5. 80 * 25 Text Mode
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 53
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Diagnostic Programs
3.8 Video
This test item is to check whether 80*25 Text Mode works normally.
In the test, user is required to respond according to the instruction in the screen.
Subtest 02
640 * 480 VGA Mode
This test item is to check whether 680*480 VGA Text mode works normally.
In the test, user is required to respond according to the instruction in the screen.
54 Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3.8 Video
3 Diagnostic Programs
Subtest 03 VESA Video Modes
This test item is to check whether all the video modes supported by the video card
works normally.
In the test, user is required to respond following the instruction in the screen.
1. 640X480 Video Modes Test
2. 800X600 Video Modes Test
3. 1024X768 Video Modes Test
Subtest 04
VESA Video Memory
This test item is to check whether VESA video memory could be correctly
accessed (write data & read data). Below is the test item’s parameter dialog
window:
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 55
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Diagnostic Programs
3.8 Video
If press Ctrl+Break to force the test to terminate during execution of VESA
Video Memory, the test program will not operate and display properly in further
tests.
Subtest 05
Subtest 06
AGP Test
This test item is to report the system’s Accelerated Graphics Port status and check
whether AGP registers works normally.
LCD Panel Test
This test item is to check whether there is any fault in its resolution by displaying
the RGB gradient color screens.
56 Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3.8 Video
3 Diagnostic Programs
Subtest 07
Subtest 08
Register Test
This test item is to check whether the registers of the video adapter works
normally.
Color Purity Test
This test item is to check whether the system (the video adapter and the display)
could display the purity color of red, green, blue, black and white.
In the test, user is required to respond according to the instruction in the screen.
Subtest 09
Direct Color Test
This test item is to check the video adapter’s composing ability of direct color in
high and true color mode.
In the test, user is required to respond according to the instruction in the screen.
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 57
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Diagnostic Programs
3.8 Video
Subtest 10
DAC/Palette Address
This test item is to check the function of DAC registers and Palette registers.
In the test, user is required to respond according to the instruction in the screen.
58 Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3.8 Video
3 Diagnostic Programs
3.9 Communication (COMM)
Subtest 01
LAN Card
This test item is to check whether the module can detect the existence of the network
card and display its related information.
1. Device ID Detection
Detect the device ID of the network card.
2. Vendor ID Detection
Detect the vendor ID of the network card.
3. MAC Address Detection
Detect the MAC address of the network card.
Subtest 02
1394
GUID Detection
This test item is used to read and display GUID from 1394 register.
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 59
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Diagnostic Programs
3.10 Peripheral
3.10 Peripheral
Subtest 01
Keyboard
This test item is to check whether the keyboard works normally.
1. Keyboard Data Line Test
Check whether the keyboard data line works normally.
2. Keyboard Clock Line Test
Check whether the keyboard clock line works normally.
Subtest 02
Mouse Test
Check whether the point devices work normally.
1. Touch Pad
Before test Touch Pad’s function, user should set a timeout time at below screen:
At the below screen of Touch Pad test, user can press the left button, right button,
and move the mouse to verify its functions for times, and the test will end either
by user break or test time is out.
60 Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3.10 Peripheral
3 Diagnostic Programs
Subtest 03
Led Test
1. Led Test
Check whether the green led works normally.
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 61
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Diagnostic Programs
3.10 Peripheral
Check whether the orange led works normally.
Check whether the HDD led works normally.
62 Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3.10 Peripheral
3 Diagnostic Programs
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 63
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Diagnostic Programs
3.11Error Codes and Description
3.11 Error Codes and description
The format of ‘Error Code’ is ‘ddxxee’, and ‘dd’ is the device ID (1~2 chars), ‘xx’ is test function
ID of device (2 chars), ‘ee’ is the error code of device (2 chars); the range of error code is from 01
to 99 in each device (the common error codes in all device are set to 99 and spanned).
Error
Code
Device
ddxx
Description
Cause
Action
ee Common Error
The test is not under interactive Check whether the interactive test
94 Interactive Mode Needed
mode.
mode is adopted.
01xx
CPU
CPU General Function
Error
The CPU General Function
register is damaged.
01
Replace the CPU.
As above.
The CPU Arithmetic Register is
damaged.
02 CPU Arithmetic Error
03 CPU Logic Error
04 CPU Type Error
05 CPU Speed Error
The CPU Logic Register is
damaged.
As above.
The CPU Type is not
supportable.
Check whether the CPU is Intel
CPU.
The CPU speed differs from the Check the CPU speed and the set
expected value.
expected speed.
Replace the CPU.
As above.
NPU General Function
Error
The NPU arithmetic unit is
damaged.
06
07 NPU Interrupt Error
The NPU is damaged.
Information of the CPU cannot Check whether the CPU is Intel
08 CPU Information Error
be acquired.
CPU.
09 Protected Instruction Error The CPU is damaged.
Replace the CPU.
02xx
Memory
The ROM BIOS has Physical
problems.
Test this unit on multiple
machines.
01 Read Error
The ROM BIOS has Physical
problems.
02 Write-Protect Error
As above.
The test pattern read out from the
Base Memory Error
Address
base memory is different from Test this memory chip on
the one that has been written in multiple machines.
this address.
03
The test pattern read out from the
extension memory is different
from the one that has been
written in this address.
04 (XMS)Memory Problem
05 (XMS) Out Of Range
As above.
Wrong parameters setup.
Check and reset the parameters.
64 Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3.11 Error Codes and Description
3 Diagnostic Programs
Interference between different
address channels.
Test this memory chip on
multiple machines.
06 Address Test Error
07 Toggle Bit Error
Errors with the timer chip.
As above.
The acquired refreshing
08 Interval Error
frequency is out of the estimated Reset the estimated range.
range.
The pattern read out from the L1
Cache is different from the one Test this unit on multiple
that has been written in the same machines.
address.
09 L1 Cache test Error
Interference between different
As above.
12 Data Bus Error
14 Speed Error
data channels.
Failure during the transfer speed
As above.
test.
03xx
Board
Repeat multiple times. Whether
DMA channel cannot transfer
there is always the same error,
data normally.
01 DMA Test Error
replace the board.
The difference between the
actual precision of the interval
timer and its theory value is out As above.
of the permitted range. The timer
counts imprecisely.
04 Interval Timer Error
The frequency is beyond the
As above.
05 Periodic Faster Error
06 Periodic Slower Error
standard.
The frequency is below the
As above.
standard.
Update-ended Interrupt
Error
R/W errors with the RTC
As above.
07
refreshing interrupt controller.
The PC speaker's sound source --
-counter/timer 8253 cannot
produce corresponding timing
08 RTC Alarm Error
As above.
signal.
13 PCI Bus Error
No PCI.
Check the board.
As above.
14 PCI Bus Scan Error
PCI test fails.
15 PCI Device Access Error PCI access fails.
As above.
Check PCI configuration on main
board or PCI Device
configuration.
PCI Config Verification
Error
16
Wrong PCI configuration.
Repeat multiple times. If there is
always the same error, replace the
board.
17 PCI to ISA Bridge Error PCI-ISA bridge errors.
18 ESCD Error
ESCD errors.
As above.
53 ACPI Table Test Error
Errors with the ACPI table test. As above.
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 65
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Diagnostic Programs
3.11Error Codes and Description
34xx
04xx
FAN
01 Fan Slow Speed Test Fail The fan slow speed test fails.
02 Fan Stop Test Fail
Check the FAN connection.
As above.
The fan stop test fails.
03 Fan Fast Speed Test Fail The fan fast speed test fails.
As above.
Video
Check whether there is any
physical problem with the video
card.
Physical problems with the video
card.
01 Text Attribute Error
02 Text Page Selection Error As above.
As above.
As above.
03 Text Color Error
04 Text Mode Error
As above.
As above.
As above.
1) Check whether there is any
physical problem with the video
card.
2) Check whether there is any
physical problem with the
monitor.
1) Physical problems with the
video card.
2) Physical problems with the
monitor.
05 VGA Mode Error
Check whether there is any
physical problem with the video
card.
Physical problems with the video
card.
06 Character Test Error
DAC/Palette Address Test
Error
07
As above.
As above.
Check whether there is any
physical problem with the video
card or the monitor.
Physical problems with the video
card or the monitor.
08 Color Purity Test Error
VESA Mode 15bits Direct
Color Test Error
09
As above.
As above.
As above.
As above.
VESA Mode 16bits Direct
Color Test Error
10
As above.
VESA Mode 24bits Direct
Color Test Error
11
As above.
Get the PCX graphics map Failure in getting PCX graphics
12
Check for the PCX graphics map.
Error
map.
Physical problems with the video Check and see whether the video
13 Bitblt Engine Test Error
card.
card has any physical problem.
VESA Video Memory
Test Error
14
As above.
As above.
Check whether there is any
physical problem with the video
card or the monitor.
Physical problems with the video
card or the monitor.
15 VESA VRAM Test Error
Check and see whether the AGP
video card has any physical
problem.
AGP configuration register
errors.
16 AGP Test Error
17 LCD Panel Test Error
Lower LCD color resolution.
Replace the LCD.
66 Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3.11 Error Codes and Description
3 Diagnostic Programs
Physical problems with the video Check and see whether the video
19 Register Test Error
card.
card has any physical problem.
The video card doesn't support
DDC.
20 Adapter not support DDC
21 Monitor not support DDC
The monitor doesn't support
DDC.
1) Check and see whether the
video card has any physical
problem.
2) Check and see whether the
monitor has any physical
problem.
1) Physical problems with the
8bits Text and Attribute video card.
21
Test Error
2) Physical problems with the
monitor.
8bits Video Mode Test
Error
26
27
As above.
As above.
As above.
As above.
15bits Video Mode Test
Error
16bits Video Mode Test
Error
28
As above.
As above.
24bits Video Mode Test
Error
29
30
As above.
As above.
As above.
As above.
32bits Video Mode Test
Error
31xx
08xx
Audio
Check the Audio connection,
replace the external fixture, and
repeat the test.
01 Audio Play Fail
Cannot play music.
Cannot record.
02 Record Fail
As above.
LAN Card
PCI bus Error during
device ID test
PCI Ethernet card not
01
Don’t Scan PCI device
Don’t support PCI BIOS
Please insert Net cad
02 present during device ID Don’t find Net card
test
Intel PCI Ethernet card
03 not present during MAC can’t be Read MAC by this
Don’t found Net Card, This Card
Please update net card or use
other method
test
method
09xx
05xx
Keyboard
Keyboard Map & Stroke Keyboard Map & Stroke Test
Test Fail
Check the KBD connection and
repeat the test.
01
fails.
03 Clock Line Test Fail
04 Data Line Test Fail
Mouse
Clock Line Test fails.
Data Line Test fails.
As above.
As above.
Check the mouse connection and
repeat the test.
01 Touch Pad Test Fail
Touch Pad Test Fail
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual 67
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Diagnostic Programs
3.11Error Codes and Description
28xx
20xx
1394
Can not find IEEE1394
controller
01
Don’t support 1394.
IDE-HDD
Wrong test parameters are input
by user.
01 Get Parameter Fail !
Reinput the correct parameters.
02 Write Pattern Error
03 Data Compare Error
04 Read Verify Error
05 Seek Error
HD is damaged.
HD is damaged.
HD is damaged.
Send the HD for repair.
As above.
As above.
HD is damaged.
As above.
Disk Controller Self Test
Failed
Disk Controller Test
07 unexpected interrupt
Failed
06
The HD controller is damaged. As above.
The HD controller is damaged. As above.
The HD controller is damaged. As above.
Disk Controller action
Test Failed
09
Disk dos not support
SMART
Change HD which supported
SMART and test again
10
Disk dos not support SMART
Disk read attribute
11
Disk read attribute threshold
error
Send the HD for repair.
threshold error
Disk read attribute value
error
12
Disk read attribute value error
As above.
As above.
Disk SMART attribute
value error
Disk SMART attribute value
error
13
21xx
ODD
No Disk in CDROM
No disk is found in the CD-
ROM.
Insert a disk into the CD-ROM.
01
The Disk in CDROM is The disk in the CD-ROM is not Insert a DATA CD.
not Data Disk Data Disk.
02
03
04
07
09
IDE-CD Controller Error Functional errors with the CD- Send the CD-ROM for repair.
ROM.
CD Read Error
CD Seek Error
Eject Error
Either the disk or the CD-ROM Replace the disk or send the CD-
is damaged. ROM for repair.
Either the disk or the CD-ROM Replace the disk or send the CD-
is damaged.
ROM for repair.
Wrong CD-ROM drive.
Exit from the wrong drive.
68 Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3.12 Quick Test Item List
3 Diagnostic Programs
3.12 Quick Test Item List
Device
Test Items
Basic Functionality
NPU Basic Functions
Comment
CPU
CPU Information
BIOS ROM
Memory
Cache Memory
Bit Stuck High Test
Bit Stuck Low Test
Address Test
10% or 3 minutes
10% or 3 minutes
Board
Interval Timer
Clock / Calendar
ACPI Test
FAN
FAN Speed
1024X768 Video Modes Test:
VESA 1024x768x64K Mode
VESA 1024x768x32bit Mode
Video
VESA Video Memory
Color Purity Test
10% or 3 minutes
25% or 3 minutes
Direct Color Test
LCD Panel
HDD
Sequential/Random Read
SMART Check
LAN Card
Device ID Detection
Vendor ID Detection
Mac Address Detection
Satellite E200,Satellite Pro E200, EQUIUM E200,SATEGO E200 Maintenance Manual i
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Replacement Procedures
4
1
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4-ii
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
Chapter 4 Contents
4.1
General.........................................................................Error! Bookmark not defined.
Safety Precautions..................................................Error! Bookmark not defined.
Before You Begin ..................................................Error! Bookmark not defined.
Disassembly Procedures ........................................Error! Bookmark not defined.
Assembly Procedures.............................................Error! Bookmark not defined.
Tools and Equipment .............................................Error! Bookmark not defined.
Screw Tightening Torque ......................................Error! Bookmark not defined.
Colors of Screw Shanks.........................................Error! Bookmark not defined.
Symbols of Screws on the Computer Body ...........Error! Bookmark not defined.
Symbol examples...................................................Error! Bookmark not defined.
Battery Pack/Bridge Media..........................................Error! Bookmark not defined.
4.2
4.2.1
Battery Pack ...........................................Error! Bookmark not defined.
Removing the Battery Pack ...................................Error! Bookmark not defined.
Installing the Battery Pack.....................................Error! Bookmark not defined.
4.2.2
Bridge Media (SD Card / Memory Stick / xDPicture Card).......... Error!
Bookmark not defined.
Removing the Bridge Media..................................Error! Bookmark not defined.
Installing the Bridge Media ...................................Error! Bookmark not defined.
Keyboard......................................................................Error! Bookmark not defined.
Removing Keyboard ..............................................Error! Bookmark not defined.
Installing the Keyboard..........................................Error! Bookmark not defined.
Bottom Cover...............................................................Error! Bookmark not defined.
Removing the Bottom Cover .................................Error! Bookmark not defined.
Installing the Bottom Cover...................................Error! Bookmark not defined.
Display Assembly ........................................................Error! Bookmark not defined.
Removing the Display Assembly...........................Error! Bookmark not defined.
Installing the Display Assembly............................Error! Bookmark not defined.
Memory Module ..........................................................Error! Bookmark not defined.
4.3
4.4
4.5
4.6
Satellite/E200/E205 Maintenance Manual
4-iii
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
Removing the Memory Module.............................Error! Bookmark not defined.
Installing the Memory Module ..............................Error! Bookmark not defined.
Wireless LAN Card......................................................Error! Bookmark not defined.
Removing the Wireless LAN Card........................Error! Bookmark not defined.
Installing the Wireless LAN Card .........................Error! Bookmark not defined.
HDD.............................................................................Error! Bookmark not defined.
Removing the HDD ...............................................Error! Bookmark not defined.
Installing the HDD.................................................Error! Bookmark not defined.
ODD Bay Module........................................................Error! Bookmark not defined.
Removing the ODD Bay Module ..........................Error! Bookmark not defined.
Installing the ODD Bay Module............................Error! Bookmark not defined.
Disassembling the ODD Drive ..............................Error! Bookmark not defined.
Assembling the ODD Drive...................................Error! Bookmark not defined.
4.7
4.8
4.9
4.10 Bluetooth module.........................................................Error! Bookmark not defined.
Removing the Bluetooth module ...........................Error! Bookmark not defined.
Installing the Bluetooth Module ............................Error! Bookmark not defined.
4.11 CPU Cooling Module and Fan.....................................Error! Bookmark not defined.
Remove the CPU cooling module and Fan............Error! Bookmark not defined.
Installing the CPU Cooling Module and Fan.........Error! Bookmark not defined.
4.12 CPU..............................................................................Error! Bookmark not defined.
Removing the CPU ................................................Error! Bookmark not defined.
Installing the CPU..................................................Error! Bookmark not defined.
4.13 System Board...............................................................Error! Bookmark not defined.
Removing the System Board .................................Error! Bookmark not defined.
Installing the System Board...................................Error! Bookmark not defined.
4.14 Speakers.......................................................................Error! Bookmark not defined.
Removing the Speakers..........................................Error! Bookmark not defined.
Installing the Speakers...........................................Error! Bookmark not defined.
4.15 Switch Board and Finger Print Board..........................Error! Bookmark not defined.
Removing Switch Board and Finger Print Board ..Error! Bookmark not defined.
Installing Switch Board and Finger Print Board....Error! Bookmark not defined.
4.16 Light Sensor Board and Audio Board..........................Error! Bookmark not defined.
4-iv
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
Removing the Light Sensor Board and Audio Board.......... Error! Bookmark not
defined.
Installing the Power Board, Switch Board and Logo LED Board................. Error!
Bookmark not defined.
4.17 DC-IN cable, RGB Board and RJ45 cable...................Error! Bookmark not defined.
Removing DC-IN cable, RGB Board and RJ45 cable......... Error! Bookmark not
defined.
Installing DC-IN cable, RGB Board and RJ45 cable .......... Error! Bookmark not
defined.
4.18 Display Mask ...............................................................Error! Bookmark not defined.
Open Display Mask................................................Error! Bookmark not defined.
Removing the Display Mask..................................Error! Bookmark not defined.
Installing the Display Mask ...................................Error! Bookmark not defined.
4.19 LCD Module ................................................................Error! Bookmark not defined.
Open LCD module.................................................Error! Bookmark not defined.
Removing the LCD module...................................Error! Bookmark not defined.
Installing the LCD Module....................................Error! Bookmark not defined.
4.20 CCD Board and MIC ...................................................Error! Bookmark not defined.
Removing the CCD Board and MIC......................Error! Bookmark not defined.
Installing the CCD Board and MIC .......................Error! Bookmark not defined.
4.21 LED Board and Card Reader Board ............................Error! Bookmark not defined.
Removing the LED Board and Card Reader BoardError! Bookmark not defined.
Installing the LED Board and Card Reader Board Error! Bookmark not defined.
Satellite/E200/E205 Maintenance Manual
4-v
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
Figures
Figure 4-1 Removing the battery pack ....................................Error! Bookmark not defined.
Figure 4-2 Removing the Bridge Media..................................Error! Bookmark not defined.
Figure 4-3 Removing the keyboard ........................................Error! Bookmark not defined.
Figure 4-4 Removing the bottom cover...................................Error! Bookmark not defined.
Figure 4-5 Removing the screws from the top of the computer ............ Error! Bookmark not
defined.
Figure 4-6 Removing the screws from the bottom of the computer and bottom cover... Error!
Bookmark not defined.
Figure 4-7 Removing the display assembly.............................Error! Bookmark not defined.
Figure 4-8 Removing the memory module..............................Error! Bookmark not defined.
Figure 4-9 Removing the wireless LAN card..........................Error! Bookmark not defined.
Figure 4-10 Removing the HDD pack.....................................Error! Bookmark not defined.
Figure 4-11 Removing the HDD chassis .................................Error! Bookmark not defined.
Figure 4-12 Removing the ODD bay module..........................Error! Bookmark not defined.
Figure 4-13 Removing the bracket from the ODD drive.........Error! Bookmark not defined.
Figure 4-14 Removing the Bluetooth module .........................Error! Bookmark not defined.
Figure 4-15 Removing the fan and CPU cooling module........Error! Bookmark not defined.
Figure 4-16 Applying silicon grease........................................Error! Bookmark not defined.
Figure 4-17 Replace new thermal pad into correct position....Error! Bookmark not defined.
Figure 4-18 Tear down the tape...............................................Error! Bookmark not defined.
Figure4-19 Removing the CPU ...............................................Error! Bookmark not defined.
Figure4-20 Removing the CPU Mylar.....................................Error! Bookmark not defined.
Figure 4-21 Installing the CPU................................................Error! Bookmark not defined.
Figure 4-22 Securing the CPU.................................................Error! Bookmark not defined.
Figure 4-23 Disconnect from system board.............................Error! Bookmark not defined.
Figure 4-24 Removing the system board.................................Error! Bookmark not defined.
Figure 4-25 Removing the speakers ........................................Error! Bookmark not defined.
Figure 4-26 Removing the switch board and finger print board............ Error! Bookmark not
defined.
Figure 4-27 Removing the touch pad and button board ..........Error! Bookmark not defined.
Figure 4-28 DC-IN cable, RGB Board and RJ45 cable...........Error! Bookmark not defined.
4-vi
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
Figure 4-29 Removing the display mask .................................Error! Bookmark not defined.
Figure 4-30 Removing the LCD module and screws...............Error! Bookmark not defined.
Figure 4-31 Removing the LCD module .................................Error! Bookmark not defined.
Figure 4-32 Removing the CCD board and MIC.....................Error! Bookmark not defined.
Figure 4-33 Removing LED Board and card reader board......Error! Bookmark not defined.
Satellite/E200/E205 Maintenance Manual
4-vii
Download from Www.Somanuals.com. All Manuals Search And Download.
4.1 General
4 Replacement Procedures
4
1
4.1 General
This chapter explains how to disassemble the computer and replace Field Replaceable Units
(FRUs). Some replacement procedures may not require you to remove all the surrounding
FRUs to replace only one FRU. The chart below shows the FRUs in the order in which they
should be removed in a top-down manner, irrespective of their physical locations. The FRUs
shown in the top area of the chart should normally be removed before removing the FRUs
shown in the bottom area. To replace the FRUs, first identify the suspect FRU for the system
failure. Next, according to this chart, determine the FRUs that need to be removed before
removing the suspect FRU. After you determine those FRUs, go to the appropriate sections
according to the section numbers shown in the boxes. Then start removal and replacement.
Battery pack/Bridge media
4.2
4. 3
Keyboard
4. 18
Wireless LAN Card
4. 4
Display Mask
LCD Modules
Bottom Cover
4.5
4. 9
4. 6
4. 21
4. 19
4. 7
Memory
module
4. 8
Cooling Module and fan
4. 11
Display
assembly
LED Board
and
Card Reader Board
HDD
ODD
Module
4. 12
CPU
4. 13
System Board
4. 20
4. 10
Bluetooth
Module
4. 14
Speakers
4. 16
4.17
DC-IN cable, RGB Board
and
RJ45 cable
4. 15
Light sensor Board
and
Audio Board
Switch board
and
Finger Print Board
CCD Board and MIC
How to use the chart (two examples):
Battery pack/Bridge media
4.2
For removing the System Board:
First, remove the top cover with the
display assembly. Then, remove the
HDD, selectable bay module,
Bluetooth card, keyboard, and
wireless LAN card, all of which are
shown above the top cover with the
display assembly.
Keyboard
4. 3
Wireless LAN Card
4. 18
4. 4
Display Mask
Bottom Cover
4.5
4. 19
4. 9
4. 6
4. 21
4. 7
4. 8
Cooling Module and fan
4. 11
Memory
module
Display
assembly
LED Board
and
HDD
ODD
Module
LCD Modules
4. 12
CPU
4. 13
Card Reader Board
System Board
4. 20
CCD Board and MIC
4. 10
Bluetooth
Module
4. 14
Speakers
4. 16
4.17
4. 15
DC-IN cable, RGB Board
For removing the LCD Module:
First, remove the display mask and
FL inverter board, both of which are
shown above the LCD module.
Light sensor Board
and
Audio Board
Switch board
and
Finger Print Board
and
RJ45 cable
System Board
LCD Module
Satellite/E200/E205 Maintenance Manual
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.1 General
Safety Precautions
Before you begin to disassembly read the following safety precautions carefully. Be sure to
follow them while you are working.
DANGER:
1.
Always use the genuine batteries or replacement batteries authorized by Toshiba.
Batteries other than those differ in specifications and are incompatible with the
computer. They may burst or explode. To avoid leakage of alkaline solutions,
never heat or disassemble the battery packs. Never throw the battery packs into a
fire. If this is violated, they will explode.
2.
The components such as the power supply and FL inverter carry high voltages.
When you partially disassemble the computer and turn on the components, use
extreme care not to touch the connectors and components to avoid the risk of
electrical shock. Do not disassemble individual components during first-level
maintenance.
WARNING:
1.
To avoid the risk of electrical shock, turn the computer off and remove the AC
adapter from the electrical outlet.
2.
Because the battery in the computer is left charged, the risk of electrical shock
remains even after the AC adapter is removed from the electrical outlet. To avoid
the risk of electrical shock, be sure to remove any metal jewelry or accessories
such as necklaces, bracelets, and rings before starting work. Never work with
damp or wet hands.
3.
To avoid personal injury, use care to avoid the sharp edges or corners of the
components.
4-2
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4.1 General
CAUTION:
4 Replacement Procedures
1.
Before replacing a component, make sure that the replacement component meets
the required specifications. To avoid computer failures, never use components
that do not meet the specifications.
2.
To avoid internal damage such as short circuits and fire, never drop metal
objects such as screws, pins, paper clips, etc. into the components. When a screw
is removed, be sure to replace a screw that is the same size as the original screw.
Make sure that all the screws are fastened securely. Loose screws can cause
short circuits, overheating, smoke, or fire.
3.
Before raising a FRU or other component, make sure that all the component
cables have been disconnected to avoid the risk of electrical shock caused by
accidental contact with the energized components.
4.
5.
For AC input, be sure to use the AC adapter and AC power cable that come with
your computer or Toshiba-recommended equivalents.
To avoid the risk of electrical shock, make sure that all the replacement
components meet the specifications of the computer and that all the cables and
connectors are fastened securely.
6.
Inside the PC are components that become hot during operation (such as the
CPU and cooling module). To avoid burns, let the hot components cool down
before starting inspection or repair task.
Satellite/E200/E205 Maintenance Manual
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.1 General
Before You Begin
Before you begin to disassembly the computer, keep in mind the precautions and advice in
this section. Always begin disassembly by removing the AC adapter and battery pack.
Remove the optional parts and accessories as well. The procedures for removing the batteries
will be explained later.
Disassemble the computer only when an abnormality has occurred.
Use only the recommended tools.
To run and store the computer, be sure to prepare a working environment that is free from:
Dust and contaminants
Static electricity
Extremely high or low temperatures and extremely high humidity
Run the diagnostic tests explained in Chapter 2 of this manual to identify the FRU that has
probably caused the system failure.
Perform only the required machine operations. Use only the disassembly and reinstallation
procedures described in this manual.
Place the removed components in a safe place away from the computer so that they are not
damaged or get in the way of you doing your work.
Normally, a number of screws need to be removed or replaced during disassembling. Place
the removed screws in a safe place so that you can easily find the right screws for the right
components.
When assembling the computer, use the specified screws to fasten the parts to the specified
locations. See the appropriate explanations and figures for screw sizes.
To avoid personal injury, use care to handle components that have sharp edges or corners.
After you have replaced a FRU, check that the FRU works correctly to ensure normal
computer operation.
4-4
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4.1 General
4 Replacement Procedures
Disassembly Procedures
The cable connectors come in these two basic types:
Pressure plate connectors
Normal pin connectors
To remove a pressure plate connector, pull up the tabs on either side of the connector's
plastic pressure plate and gently pull the cable out of the connector. To reconnect the cable to
the pressure plate's connector, raise the pressure plate up to a satisfactory height and slide the
cable into the connector. Secure the cable in the correct position by pressing down the sides
of the pressure plate so that the plate is flush with the sides of the connector. Grasp and pull
the cable gently to check that the cable is connected firmly. If the cable comes off the
connector, reinsert the cable by raising the pressure plate up to a satisfactory height.
Normal pin connectors are used for all the other types of cables. These connectors can be
installed or removed by simply inserting them or pulling them out.
Assembly Procedures
You have to reassemble the computer after you have disassembled the computer and fixed
the component that caused the problem.
When reassembling the computer, keep the following general guidelines in mind:
Take your time to carry out the suggested instructions completely. Hurried
reassembly can often cause problems.
Check that all the cable and connectors are fastened securely.
Before securing the FRUs or other parts, check that the cables are not caught by the
screws or FRUs.
Check that all the latches are closed securely.
Check that all the required screws are used to secure the FRUs. Using wrong screws
can damage the threads or heads of the screws or does not ensure that the FRUs are
secure.
After installing a FRU, make sure that the FRU and computer work normally.
Satellite/E200/E205 Maintenance Manual
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.1 General
Tools and Equipment
For your safety and that of other people in the working environment, it is strongly
recommended that you use electrostatic discharge (ESD) equipment. The proper use of this
equipment will ensure successful repair work and reduce the costs for repairing damaged
components. The equipment and tools required for disassembly and reassembly are:
One 2 mm Phillips screwdriver
One 4 mm flat-blade screwdriver
Torx screwdriver
Tweezers (for pulling out screws)
ESD mats (for the floor and work desks)
An ESD wrist strap or heel grounder
Anti-static carpets or flooring
Air ionizers (for highly electrostatic sensitive areas)
A plastic card (in credit card size)
Screw Tightening Torque
To secure screws, follow the torque values listed below. Over tightening can damage
components and screws. Under tightening can loosen the screw or cause screws to come off,
which may result in short circuits or other damage.
M2 (2 mm)
0.22 N･m (2.2 kgf･cm)
0.36 N･m (3.5 kgf･cm)
0.51 N･m (5.0 kgf･cm)
0.204 N･m (2.0 kgf･cm)
M2.5 (2.5 mm)
M3 (3 mm)
M2.5x4 PSP TITE screws
M2.5x6 GIZA TITE screws 0.36 N･m (3.5 kgf･cm)
4-6
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4.1 General
4 Replacement Procedures
Colors of Screw Shanks
For easy identification of the correct screws, the screw shanks are colored according to their
lengths, as follows:
Screws of an even-numbered length
Screws of an odd-numbered length
Screws of a special length
Brown
White
Black
Screws of a special length are those of a length having decimal places, such as 2.5
mm and 2.6 mm.
Symbols of Screws on the Computer Body
For easy maintenance, the screw types are shown on the computer body as symbols. A
symbol consists of a letter representing the screw type and a numeral representing the screw
length.
Screw type
Letter
Bind screw
B (stands for bind)
Flat-head screw
Super flat-head screw
Tapping screw
Other screws
F (stands for flat-head)
S (stands for super flat-head)
T (stands for tapping)
U (stands for unique-pan head screws, studs, etc.)
Symbol examples
6 mm bind screw
12 mm bind screw
5 mm stud
B6
B12
U5
(The numeral represents the rounded length of the threaded portion regardless of the
entire stud length.)
Satellite/E200/E205 Maintenance Manual
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.2 Battery Pack/Bridge Media
4.2 Battery Pack/Bridge Media
4.2.1 Battery Pack
Removing the Battery Pack
Remove the battery pack according to the following procedures and Figure 4-1.
CAUTION: When handling the battery packs, use care not to short circuit the
terminals. Do not drop, hit, twist, or bend the battery packs. Do not scratch or break up
their casing.
1. Turn the computer upside down so that the back is facing you.
2. Slide out the battery lock.
3. Slide the battery release latch and remove the battery pack from the computer.
Battery lock
1
2
Battery latch
Battery
Figure 4-1 Removing the battery pack
NOTE: Dispose of the used battery packs as required by local ordinances or
regulations.
4-8
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4.2 Battery Pack/Bridge Media
4 Replacement Procedures
Installing the Battery Pack
Install the battery pack according to the following procedures and Figure 4-1.
CAUTION: The battery packs contain a lithium ion battery, which can explode due to
improper replacement, use, handling, or disposal. Always dispose of the battery packs
as required by local ordinances or regulations. Use only replacement batteries
recommended by Toshiba.
NOTE: Visually check the battery's terminals. If they are dirty, clean them with a dry
cloth.
1. Gently insert a new or recharged battery pack into place. Check that the battery
release latch slides in and stops with a click.
2. Slide in the battery lock.
Satellite/E200/E205 Maintenance Manual
4-9
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.2 Battery Pack/Bridge Media
4.2.2 Bridge Media (SD Card / Memory Stick / xDPicture Card)
Removing the Bridge Media
Remove the Bridge Media according to the following procedures and Figure 4-2, after
checking that the computer is turned off in boot mode.
1. Push a Bridge media. It will pop out partly when you release, so pull out the Bridge
media.
Bridge media
Figure 4-2 Removing the Bridge Media
4-10
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4.2 Battery Pack/Bridge Media
4 Replacement Procedures
Installing the Bridge Media
Install the Bridge Media according to the following procedures and Figure 4-2, after
checking that the computer is turned off in boot mode.
1. Insert a Bridge media and press it until it is securely connected.
After the Bridge media is installed, check the hardware configuration in the Hardware Setup
or TSETUP program to make sure that the Bridge media is compatible with the current
hardware configuration.
Satellite/E200/E205 Maintenance Manual
4-11
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.3 Keyboard
4.3 Keyboard
Removing Keyboard
Remove the Keyboard according to the following procedures and Figure 4-3.
1. Release the following 10 latches on the keyboard cover, in that order:
- Five bottom latches.
- Five front latches.
2. Remove the keyboard cover.
3. Remove two M2.5x2.5 black flat head screws.
4. Disconnect the keyboard cable from CN250 and CN251 on the system board.
5. Remove the keyboard.
M2.5x2.5
black flat screw
Keyboard cover
Keyboard
Latch
CN250
CN251
Figure 4-3 Removing the keyboard
4-12
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4.3 Keyboard
4 Replacement Procedures
Installing the Keyboard
Install the keyboard according to the following procedures and Figure 4-3.
1. Connect the keyboard cable to CN250 and CN251 on the system board.
2. Secure the keyboard with two M2.5x2.5 black flat head screws.
3. Place the keyboard cover in the correct position and secure the following 10 latches,
in that order:
- Five bottom latches.
- Five front latches.
Satellite/E200/E205 Maintenance Manual
4-13
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.4 Bottom Cover
4.4 Bottom Cover
Removing the Bottom Cover
Remove the Bottom cover according to the following procedures and Figures 4-5 and 4-6.
1. Release the following 15 latches on the bottom cover, in that order:
- Four bottom latches on right sides.
- Two latches on right sides and three latches on left side.
- Six front latches.
2. Remove the bottom cover.
3. Open the display panel and remove the following 6 screws:
- Five M2x6 black flat head screws.
- One M2x5 white flat head screw.
4. Remove the left and right side hinge cover.
5. Turn the computer upside down and remove following 9 seal tapes:
- Four seal tapes on front side.
- One seal tape on right side.
- Two seal tapes on rear side
- Two seal tapes on back side.
6. Remove the following 13 screws on the bottom cover:
- Six M2.5x5 white flat head screws.
- Three M2x6 black flat head screws.
- Two M2.5x4 black flat head screws.
- Two M2.5x6 black flat head screws.
7. Hold up the bottom cover.
8. Disconnect the RGB board cable from CN204.
9. Disconnect the LED board cable from CN205.
10. Lift up the bottom cover. Release the following 15 latches on the bottom cover, in
that order:
- Four bottom latches on right sides.
- Two latches on right sides and three latches on left side.
- Six front latches.
11. Remove the bottom cover.
4-14
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4.4 Bottom Cover
4 Replacement Procedures
Latch
Bottom cover
Figure 4-4 Removing the bottom cover
M2x6 black flat
head screw
M2x5 white flat
head screw
Figure 4-5 Removing the screws from the top of the computer
M2x5 white flat
head screw
M2x6 black flat
head screw
Seal
Seal
M2.5x4 black
flat head screw
M2x5 white flat
head screw
Left side
hinge cover
Seal
Card reader
board cable
M2.5x6 black
flat head screw
Right side
hinge cover
M2x5 white flat
head screw
CN204
LED board cable
CN205
Figure 4-6 Removing the screws from the bottom of the computer and bottom cover
Satellite/E200/E205 Maintenance Manual
4-15
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.4 Bottom Cover
Installing the Bottom Cover
Install the Bottom cover with the display assembly according to the following procedures and
Figures 4-5, 4-6.
1. Hold up the bottom cover.
2. Connect the LED board cable from CN205.
3. Connect the RGB board cable from CN204.
4. Seat the bottom cover, adjusting its position.
5. Place the Left and right side hinge cover in the correct position.
6. Secure the following 13 screws on the bottom cover:
- Six M2.5x5 white flat head screws.
- Three M2x6 black flat head screws.
- Two M2.5x4 black flat head screws.
- Two M2.5x6 black flat head screws.
7. Stick following 9 seal tapes:
- Four seal tapes on front side.
- One seal tape on right side.
- Two seal tapes on rear side
- Two seal tapes on back side.
8. Place the bottom cover in the correct position and secure the following 15 latches, in
that order:
- Four bottom latches on right sides.
- Two latches on right sides and three latches on left side.
- Six front latches.
9. Restore the normal computer placement then open the display panel and secure the
following 6 screws:
- Five M2x6 black flat head screws.
- One M2x5 white flat head screw.
4-16
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4.5 Display Assembly
4 Replacement Procedures
4.5 Display Assembly
Removing the Display Assembly
Remove the display assembly according to the following procedures and Figures 4-7.
1. Open the display panel at an angle of 90 degrees.
2. Turn the computer upside down.
3. Disconnect the CCD cable from CN2250 on the system board.
4. Disconnect the MIC cable from CN208 on the system board.
5. Disconnect the LCD cable from CN3000 on the system board.
6. Remove two M2.5x4 black flat head screws securing the LCD module to the top
cover.
CN208
CN2250
CCD cable
CN3000
MIC cable
M2.5x4 black flat head screw
LCD cable
Figure 4-7 Removing the display assembly
Satellite/E200/E205 Maintenance Manual
4-17
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.5 Display Assembly
Installing the Display Assembly
Install the display assembly according to the following procedures and Figures 4-7.
1. Place the display panel in the correct position.
2. Connect the CCD cable to CN2250 on the system board.
3. Connect the MIC cable to CN208 on the system board.
4. Connect the LCD cable to CN3000 on the system board.
5. Secure the display assembly with two M2.5x4 black flat head screws.
6. Close the display panel
4-18
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4.6 Memory Module
4 Replacement Procedures
4.6 Memory Module
Removing the Memory Module
Remove the memory module according to the following procedures and Figures 4-8, after
checking that the computer is turned off in boot mode.
CAUTION: Do not touch the connectors on the memory modules or in the computer.
Contaminated connectors can cause memory access problems.
Memory
Memory slot
Latches
Figure 4-8 Removing the memory module
1. Spread out the two memory lock latches so that the memory module pops up.
2. Pull the memory module up and out at an angle, using care to avoid touching the
connectors.
Satellite/E200/E205 Maintenance Manual
4-19
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.6 Memory Module
Installing the Memory Module
Install the memory module according to the following procedures and Figures 4-8, after
checking that the computer is turned off in boot mode.
Note: The slot A is reserved for main memory. Use the slot B for expanded memory. If
only one card is installed, use the slot A.
1. Insert the memory module into the connector at an angle of 45 degrees.
2. Press down on the memory module so that it is secured with both memory lock
latches.
After the computer is turned on, check the hardware configuration in the Hardware Setup or
TSETUP program to make sure that the installed memory module has been recognized by the
system. If it has not been recognized yet, check the connections
4-20
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4.7 Wireless LAN Card
4 Replacement Procedures
4.7 Wireless LAN Card
Removing the Wireless LAN Card
Remove the wireless LAN card according to the following procedures and Figure 4-9.
CAUTION: Do not touch the connectors on the wireless LAN card and in the computer
with your bare hands. Wireless LAN cards can fail if they are contaminated with sweat,
natural oils, etc. from your hands.
1. Disconnect the two antenna cables with tweezers.
2. Remove the one M2x3 black flat head screw securing the wireless LAN card.
3. Pull the wireless LAN card up from CN1300 on the system board and out at an angle.
M2x3 black flat
head screw
Black cable
White cable
CN1300
Wireless LAN card
Figure 4-9 Removing the wireless LAN card
Satellite/E200/E205 Maintenance Manual
4-21
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.7 Wireless LAN Card
Installing the Wireless LAN Card
Install the wireless LAN card according to the following procedures and Figure 4-9.
1. Insert the wireless LAN card into the CN1300 an angle of 45 degrees.
2. Press down on the wireless LAN card to secure it with one M2x3 black flat head
screw.
3. Connect the two antenna cables by pressing them firmly into place.
CAUTION: Do not touch the connectors on the wireless LAN card and in the computer
with your bare hands. Wireless LAN cards can fail if they are contaminated with sweat,
natural oils, etc. from your hands.
4-22
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4.8 HDD
4 Replacement Procedures
4
1
4.8 HDD
Removing the HDD
CAUTION: Do not press on the top or bottom of the drive.
Applying such pressure can either corrupt the data in the drive or
damage the drive.
Remove the HDD (hard disk drive) according to the following procedures and Figures 4-
10, 4-11.
1. Removing the two M2x3 black flat head screws.
M2x3 black flat head screw
HDD
Figure 4-10 Removing the HDD pack
Satellite/E200/E205 Maintenance Manual
4-23
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.8 HDD
2. Remove the HDD pack by pulling on the tab attached to the pack.
NOTE: Do not disassemble the HDD pack when it is working normally. Disassemble or
replace the HDD pack only if it fails.
3. Place the HDD pack on a flat surface (such as a desk), and remove the four M3x4
black flat head screws.
4. Place the HDD pack on a flat surface (such as a desk), and remove the chassis.
HDD
M3x4 black flat
head screw
HDD chassis
M3x4 black flat
head screw
Figure 4-11 Removing the HDD chassis
CAUTION: Do not apply pressure to the top or bottom of the drive.
4-24
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4.8 HDD
4 Replacement Procedures
Installing the HDD
Install the HDD according to the following procedures and Figures 4-10, 4-11.
CAUTION: To avoid damage, always hold the HDD only by its sides.
1. Attach the HDD chassis.
2. Secure the HDD and its chassis with the four M3x4 black head screws.
CAUTION: To prevent the HDD bracket from being distorted when installing the HDD
pack into the computer, do not press the center of the HDD pack. Always hold the HDD
pack by its sides.
3. Install the HDD pack into the correct position in the computer. Connect the HDD
pack to the computer, holding the HDD pack by its sides.
4. Insert the HDD pack.
5. Secure the HDD pack with two M2x3 black flat head screws.
Satellite/E200/E205 Maintenance Manual
4-25
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.9 ODD Bay Module
4.9 ODD Bay Module
Removing the ODD Bay Module
NOTE: The installation and removal procedures are the same for all the modules that
can be installed in the ODD bay. See the appropriate sections for the disassembly
procedures of specific modules.
Remove the ODD bay module according to the following procedures and Figures 4-12.
1. Remove the three M2x3 black flat head screws.
2. Push out on the ODD bay module.
CAUTION: Handle the ODD bay module carefully it can become hot during operation.
M2x3 black flat head screw
ODD bay module
Figure 4-12 Removing the ODD bay module
4-26
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4.9 ODD Bay Module
4 Replacement Procedures
Installing the ODD Bay Module
Install the ODD bay module according to the following procedures and Figures 4-12.
1. Place the ODD bay module in the correct position and slide it in.
2. Push it in until it clicks into place.
3. Secure the ODD bay module with three M2x3 black flat head screws.
Satellite/E200/E205 Maintenance Manual
4-27
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.9 ODD Bay Module
Disassembling the ODD Drive
NOTE: Do not disassemble the ODD drive when it is working normally. Disassemble or
replace the ODD drive only if it fails.
Disassemble the ODD drive according to the following procedures and Figure 4-13.
1. Remove four M2x3 black flat head screws.
2. Remove the two brackets.
3. Release the following 4 latches on the slot ODD bezel, in that order:
- Two above latches.
- Two below latches.
ODD
Latch
ODD bezel
M2x3 black flat
ODD bracket
head screw
M2x3 black flat head screw
ODD side bracket
Figure 4-13 Removing the bracket from the ODD drive
Assembling the ODD Drive
Assemble the ODD drive according to the following procedures and Figure 4-13.
1. Place the slot ODD bezel in the correct position and secure the following 4 latches, in
that order:
- Two above latches.
- Two below latches.
2. Seat the two brackets and secure it with four M2x3 black flat head screws.
4-28
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4.10 Bluetooth Module
4 Replacement Procedures
4.10 Bluetooth module
Removing the Bluetooth module
NOTICE: Don’t touch the double tape surface for keep double tape surface clean and
adhesive while remove the Bluetooth module from the ODD bracket.
Remove the Bluetooth module according to the following procedures and Figures 4-14.
1. Disconnect the Bluetooth cable from CN2150 on the system board.
2. Remove M1.6x2.5 white flat head screw.
3. Remove the Bluetooth module.
4. Disconnect the Bluetooth cable from the Bluetooth module.
M1.6x2.5 white
flat head screw
CN2150
Figure 4-14 Removing the Bluetooth module
Satellite/E200/E205 Maintenance Manual
4-29
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.10 Bluetooth Module
Installing the Bluetooth Module
Install the Bluetooth module according to the following procedures and Figures 4-14.
1. Connect the Bluetooth cable to the Bluetooth module.
2. Place the Bluetooth module in the correct position.
3. Secure the Bluetooth module with M1.6x.2.5 white flat head screw.
4. Connect the Bluetooth cable to CN2150 on the system board.
4-30
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4.11 CPU Cooling Module and Fan
4 Replacement Procedures
4.11 CPU Cooling Module and Fan
CAUTION: When removing the cooling module, keep the following in mind:
The cooling module can become very hot during operation. Be sure to let it cool down
before starting the repair work.
Do not touch or cause damage to the fan in the cooling module.
Remove the CPU cooling module and Fan
Remove the CPU cooling module and fan according to the following procedures and
Figures 4-15, 4-16, 4-17 and 4-18.
1. Disconnect the fan cable from CN4300 on system board.
2. Remove one M2x6 black flat head screw on the fan.
3. Remove the fan.
4. Release six CPU thermal securing screws on the CPU cooling module.
5. Remove the CPU cooling module.
M2x6 black flat
head screw
Fan
CPU cooling module
securing screw
CPU cooling module
CN4300
Figure 4-15 Removing the fan and CPU cooling module
Satellite/E200/E205 Maintenance Manual
4-31
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.11 CPU Cooling Module and Fan
Figure 4-16 Applying silicon grease
Thermal pad
CPU cooling module
Figure 4-17 Replace new thermal pad into correct position.
Tape
Thermal pad
Figure 4-18 Tear down the tape.
4-32
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4.11 CPU Cooling Module and Fan
4 Replacement Procedures
Installing the CPU Cooling Module and Fan
Install the cooling Module according to the following procedures and Figures 4-15, 4-16,
4-17 and 4-18.
CAUTION: When installing the cooling module, keep the following in mind:
1. Be sure to confirm the correct position for the module.
2. Secure the relevant screws on the main board according to the number sequence
sealed on the heat sink module.
NOTE: Apply silicon grease with a special syringe to cover the surface of the CPU chip
completely.
1. If the thermal pad is broken, replace new thermal pad into correct position, thermal
pad part number V000934140 for Mainz10 and V000941970 for Mainz10G.
2. If silicon grease is already applied to the CPU and fan module, wipe it off with a
cloth.
By using a special syringe, apply silicon grease G7762 to the CPU chip center so that
the entire CPU chip is covered with the grease G7762.
3. Install the CPU cooling module into the correct position on the system board.
4. Place the CPU cooling module in the correct position and secure it with six CPU
thermal module securing screws.
5. Place the fan in the correct position and secure it with one M2x6 black flat head
screw.
6. Connect the fan cable to CN4300 on the system board.
Satellite/E200/E205 Maintenance Manual
4-33
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.12 CPU
4.12 CPU
Removing the CPU
CAUTION: When removing the CPU, keep the following in mind:
The CPU can become very hot during operation. Be sure to let it cool down before
starting repair work.
Remove the CPU according to the following procedures and Figures 4-19, 4-20, 4-21 and
4-22.
NOTE: FOXCONN CPU socket will be 180 degrees to the right.
1. Unlock the CPU by rotating the cam on the CPU socket 120 degrees to the left with a
flat-blade screwdriver (in the order shown in the figure below).
2. Remove the CPU.
3. Remove the CPU Mylar.
Figure4-19 Removing the CPU
CPU Mylar
CPU
Figure4-20 Removing the CPU Mylar
4-34
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4.12 CPU
4 Replacement Procedures
Installing the CPU
Install the CPU according to the following procedures and Figures 4-20, 4-21 and 4-22.
1. Check that the triangle on the cam is in the unlock position.
2. Stick the CPU Mylar on the CPU.
3. Attach the CPU to the correct position in the CPU socket. Align the CPU with the
CPU socket by using the triangle as a guide.
Figure 4-21 Installing the CPU
CAUTION: Seat the CPU by aligning the triangle with the shaded area.
Satellite/E200/E205 Maintenance Manual
4-35
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.12 CPU
4. Secure the CPU by rotating the cam 120 degrees to the right with a flat-blade screwdriver.
NOTE: FOXCONN CPU socket will be 180 degrees to the left.
Figure 4-22 Securing the CPU
4-36
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4.13 System Board
4 Replacement Procedures
4.13 System Board
Removing the System Board
Remove the System Board according to the following procedures and Figure 4-23, 4-24.
1. Disconnect the light sensor cable from CN202 on system board.
2. Disconnect the RGB cable from CN3050 on system board.
3. Disconnect the RJ45 cable from CN470 on system board.
4. Disconnect the touch pad flat cable from CN280 on system board.
5. Disconnect the switch board cable from CN281 on system board.
6. Disconnect the finger print board cable from CN209 on system board.
7. Turn the top cover upside down.
8. Disconnect the audio board flat cable from CN201 on system board.
9. Disconnect the DC-IN cable from CN6000 on system board.
10. Disconnect the MMB board flat cable from CN200 on system board.
11. Remove three M2x3 black flat head screws.
12. Remove the system board.
Satellite/E200/E205 Maintenance Manual
4-37
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.13 System Board
Light sensor cable
Touch pad flat cable
RGB cable
RJ45 cable
CN470
CN202
CN3050
CN209
CN281
CN280
Switch board
flat cable
Finger print board cable
Figure 4-23 Disconnect from system board
M2x3 black flat head screw
System board
CN200
CN6000
CN201
Audio board
flat cable
MMB board flat cable
DC IN cable
Figure 4-24 Removing the system board
4-38
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4.13 System Board
4 Replacement Procedures
Installing the System Board
Note: Be careful of the Kill switch knob position for the kill switch. It can be damaged
when installing the system board. Make sure its position is same as kill switch on system
board..
Install the System Board according to the following procedures and figure 4-23, 4-24.
1. Seat the system board in the correct position.
2. Secure the system board with three M2x3 black flat head screws.
3. Connect the audio board flat cable from CN201 on system board.
4. Connect the DC-IN cable from CN6000 on system board.
5. Connect the MMB board flat cable from CN200 on system board.
6. Restore the normal top cover placement.
13. Connect the light sensor cable from CN202 on system board.
14. Connect the RGB cable from CN3050 on system board.
15. Connect the RJ45 cable from CN470 on system board.
16. Connect the touch pad flat cable from CN280 on system board.
17. Connect the switch board cable from CN281 on system board.
7. Connect the finger print board cable from CN209 on system board.
Satellite/E200/E205 Maintenance Manual
4-39
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.14 Speakers
4.14 Speakers
Removing the Speakers
Remove the Speakers according to the following procedures and Figure 4-25.
1. Remove five M2x3 black flat head screws and two M2x2.5 black flat head screws
from shield.
2. Remove the shield.
3. Disconnect the speaker cable from CN9801 on the audio board.
4. Remove two M2x3 black flat head step screw securing the left speaker.
5. Remove two M2x3 black flat head step screws securing the right speaker.
6. Remove the left and right speakers.
M2x3 black flat
head screw
M2x2.5 black
flat head screw
M2x3 black flat
head screw
M2x3 black flat
head step screw
M2x3 black flat
head step screw
Right speaker
Shield
Left cable
CN9801
Figure 4-25 Removing the speakers
4-40
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4.14 Speakers
4 Replacement Procedures
Installing the Speakers
Install the speakers according to the following procedures and Figure 4-25.
1. Seat the left and right speaker in the correct position.
2. Route the speaker cable in the wire guide.
3. Secure the left speaker with two M2x3 black flat head step screws.
4. Secure the right speaker with two M2x3 black flat head step screws.
5. Connect the speaker cable to CN9801 on the audio board.
6. Seat the left and right speaker in the correct position.
7. Seat the shield in the correct position.
8. Secure the shield with five M2x3 black flat head screws and two M2x2.5 black flat
head screws.
Satellite/E200/E205 Maintenance Manual
4-41
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.15 Switch Board and Finger Print Board
4.15 Switch Board and Finger Print Board
Removing Switch Board and Finger Print Board
Remove the Switch Board and Finger Print Board according to the following procedures and
Figure 4-26.
1. Remove one M2x3 black flat head screw securing the switch board.
2. Remove the switch board.
3. Disconnect the switch board flat cable from CN9400 on the switch board.
2. Remove the touch pad hold.
3. Remove the finger print board.
CN9400
Switch board flat cable
Switch board
M2x3 black flat
head screw
Touch pad holder
Finger print board
Figure 4-26 Removing the switch board and finger print board
4-42
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4.15 Switch Board and Finger Print Board
4 Replacement Procedures
Installing Switch Board and Finger Print Board
Install Switch Board and Finger Print Board to the following procedures and Figure 4-26.
1. Seat the finger print board in the correct position.
2. Seat the touch pad hold in the correct position.
3. Connect the switch board flat cable to CN9400 on the switch board.
4. Seat the switch board in the correct position.
5. Secure the switch board with one M2x3 black flat head screw.
Satellite/E200/E205 Maintenance Manual
4-43
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.16 Light Sensor Board and Audio Board
4.16 Light Sensor Board and Audio Board
Removing the Light Sensor Board and Audio Board
Remove the Light Sensor Board and Audio Board according to the following procedures and
Figure 4-27.
1. Remove one M2x3 black flat head screw and remove the light sensor board.
2. Remove one M2x3 black flat head screw and remove the audio board.
3. Disconnect the audio board flat cable from CN9803 on the audio board.
M2x3 black flat
head screw
Light sensor board
Audio board
Audio board flat cable
CN9803
Figure 4-27 Removing the touch pad and button board
4-44
Satellite/E200/E205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4.16 Light Sensor Board and Audio Board
4 Replacement Procedures
Installing the Power Board, Switch Board and Logo LED Board
Install the Light Sensor Board and Audio Board according to the following procedures and
Figure 4-27.
1. Seat the light sensor board in the correct position and secure it with the one M2x3
black flat head screw.
2. Connect the audio board flat cable to CN9803 on the audio board.
3. Seat the audio board in the correct position and secure it with the two M2x3 black flat
head screw.
Satellite/E200/E205 Maintenance Manual
4-45
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.17 DC-IN cable, RGB Board and RJ45 cable
4.17 DC-IN cable, RGB Board and RJ45 cable
Removing DC-IN cable, RGB Board and RJ45 cable
Remove the DC-IN cable, RGB Board and RJ45 cable according to the following procedures
and Figure 4-28.
1. Remove the DC-IN cable.
2. Remove two M2x3 black flat head screws securing the RGB board and one M2x3
black flat head screw securing the RGB cable.
3. Remove the RGB board.
4. Disconnect the RGB cable from CN9600 on the RGB board.
5. Remove two M2x3 black flat head screws securing the IO bracket and IO bracket
cover.
6. Remove two M2x3 black flat head screws securing the IO bracket cover.
7. Remove the RJ45 cable.
RGB board cable
RJ45 cable
M2x3 black flat
head screw
DC-IN cable
M2x3 black flat
head screw
RGB board
IO bracket
IO bracket cover
Figure 4-28 DC-IN cable, RGB Board and RJ45 cable
4-46
Satellite/E200/E205 Maintenance
Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4.17 DC-IN cable, RGB Board and RJ45 cable
4 Replacement Procedures
Installing DC-IN cable, RGB Board and RJ45 cable
Install the DC-IN cable, RGB Board and RJ45 cable to the following procedures and Figure
4-28.
1. Seat the RJ45 cable in the correct position.
2. Seat IO bracket cover in the correct position of IO bracket, then secure it with
two M2x3 black flat head screws
3. Seat IO bracket and IO bracket cover in the correct position of top cover then
secure them with two M2x3 black flat head screws.
4. Seat the DC-IN cable in the correct position.
5. Seat the RGB board in the correct position.
6. Secure the RGB board with two M2x3 black flat head screws.
7. Connect the RGB cable to CN9600 on the RGB board.
8. Secure the RGB board cable with one M2x3 black flat head screw.
Satellite/E200/E205 Maintenance Manual
4-47
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.18 Display Mask
4.18 Display Mask
Open Display Mask
Removing the Display Mask
Disassemble the display mask according to the following procedures and Figure 4-29.
1. Peel off four seal tapes and remove four M2.5x4 white flat head screws securing the
display mask.
2. Insert your finger between the edge of display mask and the LCD and remove the
display mask while unlatching the display mask.
Seal
M2.5x4 white flat head screw
Seal
Display mask
M2.5x4 white flat head screw
Figure 4-29 Removing the display mask
4-48
Satellite/E200/E205 Maintenance
Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4.18 Display Mask
4 Replacement Procedures
Installing the Display Mask
Install the display mask according to the following procedures and Figure 4-29.
1. Install the display mask and lock the latches.
NOTE: When installing the display mask, ensure there is no gap between the display
mask and the display cover.
2. Secure the display mask with four 2.5x4 white flat head screws and stick four seal tapes
on the front.
Satellite/E200/E205 Maintenance Manual
4-49
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.19 LCD Module
4.19 LCD Module
NOTE: ICs are fragile. Use extreme care not to apply pressure to the ICs along the
edges of the LCD module.
NOTE: Dispose of used LCD panels as required by local ordinances or regulations.
NOTE: The LCD cable must be carefully peeled away before disconnecting it from the
module.
Open LCD module
Removing the LCD module
Remove the LCD module according to the following procedures and Figures 4-30, 4-31.
1. Remove the Left and right LCD hinge bracket cover.
2. Remove two M2.5x4 white flat head screws on each side securing the LCD bracket.
3. Carefully tilt the LCD module toward you.
4. Remove two M2x3 black flat head screws on each securing the LCD bracket.
5. Remove the LCD brackets.
6. Turn the LCD upside down. Be sure to place it on a cushioned surface such as a foam
pad.
4-50
Satellite/E200/E205 Maintenance
Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4.19 LCD Module
4 Replacement Procedures
Left LCD bracket
LCD module
Right LCD bracket
M2x3 black flat
head screw
Left LCD bracket cover
M2x3 black flat
head screw
Right LCD bracket cover
M2.5x4 white flat head screw
Figure 4-30 Removing the LCD module and screws
7. Disconnect the LCD cable from LCD module.
LCD module
LCD cable
Figure 4-31 Removing the LCD module
Satellite/E200/E205 Maintenance Manual
4-51
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.19 LCD Module
Installing the LCD Module
NOTE: LCD cable must be carefully peeled away before connecting it from the module.
Install the LCD module according to the following procedures and Figures 4-30, 4-31.
1. Turn the LCD upside down.
2. Connect the LCD cable to the LCD module connector.
3. Turn the LCD right side up.
4. Place the LCD bracket in the correct position and secure it with two M2x3 black flat
head screws on each side.
5. Place the LCD module in the correct position and secure it with two M2.5x4 white
flat heat screws on each side.
6. Place the LCD hinge bracket cover on correct position of LCD hinge.
CAUTION: When installing the LCD module, please follow below instruction:
When plug in LCD/FL cable into LCD module connector, need to plug horizontally. For
Sharp panel, if LCD/FL cable connector is not plugged horizontally, it may be damaged.
4-52
Satellite/E200/E205 Maintenance
Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4.19 LCD Module
4.20 CCD Board and MIC
4.20 CCD Board and MIC
Removing the CCD Board and MIC
Remove the FL inverter board according to the following procedures and Figure 4-32.
1. Remove the CCD module with CCD cable from display rear cover.
2. Disconnect the CCD cable from the CCD module connector.
MIC cable
CCD module
CCD cable
Display rear cover
Figure 4-32 Removing the CCD board and MIC
3. Lift the MIC from the display rear cover.
Satellite/E200/E205 Maintenance Manual
4-53
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.20 CCD Board and MIC
Installing the CCD Board and MIC
Install the FL inverter board according to the following procedures and Figure 4-32.
1. Connect the CCD module cable to CCD module connector.
2. Seat the CCD module, MIC in the correct position.
4-54
Satellite/E200/E205 Maintenance
Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4.21 LED Board and Card Reader Board
4 Replacement Procedures
4.21 LED Board and Card Reader Board
Removing the LED Board and Card Reader Board
Remove the LED Board and Card Reader Board according to the following procedures and
Figure 4-33.
1. Remove two M2x3 black flat head screws and remove the LED lens.
2. Remove one M2x3 black flat head screw and remove the LED board.
3. Disconnect the LED board cable from CN9500 on the LED board.
4. Remove two M2x3 black flat head screws and remove the card reader board.
5. Disconnect the card reader board cable from CN9903 on the card reader board.
M2x3 black flat head screw
LED lens
LED board cable
CN9903
CN9500
LED board
Card reader board cable
Card reader board
M2x3 black flat head screw
Figure 4-33 Removing LED Board and card reader board
Satellite/E200/E205 Maintenance Manual
4-55
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.21 LED Board and Card Reader Board
Installing the LED Board and Card Reader Board
Install the LED Board and Card Reader Board according to the following procedures and
Figure 4-33.
1. Connect the card reader board cable to CN9903 on the card reader board.
2. Seat the card reader board in the correct position and secure it with the two M2x3
black flat head screws.
3. Connect the LED board cable to CN9500 on the LED board.
4. Seat the LED board in the correct position and secure it with the one M2x3 black flat
head screw.
5. Seat the LED lens in the correct position and secure it with the two M2x3 black flat
head screws.
4-56
Satellite/E200/E205 Maintenance
Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
6000 1 次
Appendices
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Appendix
Contents
Appendix A Handling the LCD Module.......................................................................... A-1
Appendix B Board Layout .................................................................................................B-1
B.1
B.2
System Board Front View......................................................................................B-1
System Board Back View ......................................................................................B-2
Appendix C.......................................................................................................................... C-2
C.1
C.2
C.3
C.4
C.5
C.6
CN200
CN201
CN202
CN204
CN205
Hot key Connector (6-Pin) ..............Error! Bookmark not defined.
Audio Connector (24-Pin) ...............Error! Bookmark not defined.
Light sensor BD Connector (4-Pin).Error! Bookmark not defined.
Card Reader Connector (8-Pin) .......Error! Bookmark not defined.
LED Connector (20-Pin)..................Error! Bookmark not defined.
Intermal Micro Phone Connector (2-Pin)...... Error! Bookmark not
CN208
defined.
C.7
CN209
CN250
CN251
CN280
Finger Print BD Connector (4-Pin) .Error! Bookmark not defined.
Keyboard Cable Connector (34-Pin)Error! Bookmark not defined.
Hot key BD Connector (4-Pin)........Error! Bookmark not defined.
Touchpad Connector (6-Pin) ...........Error! Bookmark not defined.
Touchpad ON/OFF Connector (4-Pin).......... Error! Bookmark not
C.8
C.9
C.10
C.11
CN281
defined.
C.12
C.13
CN470
RJ45 LAN Port Connector (12-Pin) Error! Bookmark not defined.
CN1300
Wireless LAN Module Connector (52-Pin)... Error! Bookmark not
defined.
C.14
C.15
C.16
C.17
C.18
C.19
C.20
C.21
CN1401
CN1700
CN1750
CN1800
CN2000
CN2150
CN2250
CN3000
SIM Card Connector (6-Pin) ...........Error! Bookmark not defined.
SATA HDD Connector (22-Pin) .....Error! Bookmark not defined.
SATA ODD Connector (13-Pin) .....Error! Bookmark not defined.
e-SATA Port Connector (11-Pin)....Error! Bookmark not defined.
USB#0 Connector (4-Pin)................Error! Bookmark not defined.
Bluetooth Cable Connector (10-Pin)Error! Bookmark not defined.
Camera Cable Connector (5-Pin).....Error! Bookmark not defined.
LCD Cable Connector (40-Pin).......Error! Bookmark not defined.
App-ii
Satellite E200/205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
C.22
C.23
C.24
CN3050
CN3150
RGB Connector (14-Pin) .................Error! Bookmark not defined.
HDMI Port Connector (19-Pin ).......Error! Bookmark not defined.
DDR3 So-Dimm0 Connector (204-Pin) ......... Error! Bookmark not
CN4100
defined.
C.25
CN4101
DDR3 So-Dimm1 Connector (204-Pin) ......... Error! Bookmark not
defined.
C.26
C.27
C.28
C.29
CN4300
CN6000
CN6970
FAN Connector (3-Pin) ....................Error! Bookmark not defined.
DC-IN Cable Connector (4-Pin).......Error! Bookmark not defined.
Battery Connector (9-Pin).................Error! Bookmark not defined.
Touchpad ON/OFF BD Connector (4-Pin)..... Error! Bookmark not
CN9400
defined.
C.30
C.31
C.32
C.33
C.34
C.35
C.36
C.37
C.38
C.39
CN9500
CN9600
CN9601
CN9801
CN9802
CN9803
CN9900
CN9903
LED BD Connector (20-Pin)........................................................ C-19
RGB BD Connector (14-Pin)......................................................... C-20
RGB BD to MB Connector (15-Pin) ............................................. C-20
Speaker Connector (4-Pin) ............................................................ C-21
USB#1 Connector (4-Pin).............................................................. C-21
Audio BD Connector (24-Pin)....................................................... C-21
Card Reader BD Connector (38-Pin)............................................. C-22
Card Reader BD to MB Connector (8-Pin) ................................... C-22
JACK9800 SPDIF/ Head Phone Connect (6-Pin)............................................ C-23
JACK9801 Ezternal MIC Connector (6-Pin)................................................... C-23
Appendix D Keyboard Scan/Character Codes................................................................ D-1
Appendix E Key Layout .................................................................................................... E-1
Satellite E200/205 Maintenance Manual
App-iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Apx. A Handling the LCD Module
Appendices
Appendix A
Appendix A Handling the LCD Module
Precautions for handling the LCD module
The LCD module can be easily damaged during assembly or disassembly. Observe the
following precautions when handling the LCD module:
1. When installing the LCD module in the LCD cover, be sure to seat it so that it is
properly aligned and maximum visibility of the display is maintained.
2. Be careful to align the four holes at the right side and left side of the LCD module
with the corresponding holes in the LCD cover before securing the module with four
screws. Do not force the module into place, because stress can affect its performance.
Also, the panel’s polarized surface is easily scarred, so be carefully when handling it.
Satellite E200/205 Maintenance Manual
A-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Apx. A Handling the LCD Module
3. If the panel’s surface gets dirty, wipe it with cotton or a soft cloth. If it is still dirty,
try breathing on the surface to create a light condensate and wipe it again.
If the surface is very dirty, we recommend a CRT cleaning agent. Apply the agent to
a cloth and then wipe the panel’s surface. Do not apply cleanser directly to the panel.
Also, never scratch the surface.
4. If water or other liquid is left on the panel’s surface for a long period, it can change
the screen’s tint or stain it. Be sure to quickly wipe off any liquid.
A-2
Satellite E200/205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Apx. A Handling the LCD Module
Appendices
5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object,
which could cause breakage or cracks.
6. CMOS-LSI circuits are used in the module, so guard against damage from
electrostatic discharge. Be sure to wear a wrist or ankle ground when handling the
module.
Satellite E200/205 Maintenance Manual
A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Apx. A Handling the LCD Module
7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods.
8. Do not store the module at temperatures below specifications. Cold can cause the
liquid crystals to freeze, lose their elasticity or otherwise suffer damage.
A-4
Satellite E200/205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Apx. A Handling the LCD Module
Appendices
9. Do not disassemble the LCD module. Disassembly can cause malfunctions.
10. If you transport the module, do not use packing material that contains epoxy resin
(amine) or silicon glue (alcohol or oxime). These materials can release gas that can
damage the panel’s polarization.
Satellite E200/205 Maintenance Manual
A-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Apx. B Board Layout
Appendices
Appendix B
Appendix B Board Layout
B.1
System Board Front View
Figure B-1 Board layout (front)
Satellite E200/205 Maintenance Manual
B-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Apx. B Board Layout
B.2
System Board Back View
Figure B-2 Board layout (back)
B-2
Satellite E200/205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Apx. C Pin Assignments
LED BD Connector (20-Pin).......................................................C-19
C.30
CN9500
Satellite E200/205 Maintenance Manual
C-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Apx. C Pin Assignments
C.31
C.32
C.33
C.34
C.35
C.36
C.37
C.38
C.39
CN9600
RGB BD Connector (14-Pin) ..........................................................C-20
RGB BD to MB Connector (15-Pin)...............................................C-20
Speaker Connector (4-Pin)..............................................................C-21
USB#1 Connector (4-Pin) ...............................................................C-21
Audio BD Connector (24-Pin) ........................................................C-21
Card Reader BD Connector (38-Pin) ..............................................C-22
Card Reader BD to MB Connector (8-Pin).....................................C-22
CN9601
CN9801
CN9802
CN9803
CN9900
CN9903
JACK9800 SPDIF/ Head Phone Connect (6-Pin) .............................................C-23
JACK9801 Ezternal MIC Connector (6-Pin).....................................................C-23
C-2
Satellite E200/205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Apx. C Pin Assignments
Appendix C
Appendix C
Pin Assignments
System Board
C.1
CN200
Hot key Connector (6-Pin)
Table C-1 Hot key Connector pin assignments (6-Pin)
Pin No
Signal Name
+V3LA
I/O Pin No.
Signal Name
+V5A
I/O
-
1
3
-
O
O
-
2
4
HOTKEY_INT#
EC_SMB3_DATA
DGND
DGND
-
5
6
EC_SMB3_CLK
DGND
O
-
G1
G2
C.2
CN201
Audio Connector (24-Pin)
Table C-2 Audio Connector pin assignments (24-Pin)
Pin No.
Signal Name
MIC_IN
I/O Pin No.
Signal Name
DGND
I/O
-
1
3
O
O
-
2
PCSPKR
4
MMB_BEEP
USB_N_P2
DGND
O
I/O
5
DGND
6
I/O
7
USB_P_P2
SB_USB_1
DGND
8
-
I
9
O
-
10
12
14
16
18
20
22
USB_OC#_1
AC97_3S_BITCLK
AC97_3S_SYNC
AC97_3S_SDOUT
+V3S
11
13
15
O
O
O
-
AC97_3S_RST#
AC97_3S_SDIN0
O
I
17 AMP_SHUTDOWN
O
-
19
21
+V3S
+V5A
+V5A
-
-
+V5A
-
Satellite E200/205 Maintenance Manual
C-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Apx. C Pin Assignments
23
+V5A
-
-
24
+V5A
-
-
G1
DGND
G2
DGND
C.3
CN202
Light sensor BD Connector (4-Pin)
Table C-3 Light sensor BD Connector pin assignments (4-Pin)
Pin No.
Signal Name
+V3S
I/O Pin No.
Signal Name
EC_SMB3_CLK
DGND
I/O
O
-
1
3
-
O
-
2
4
EC_SMB3_DATA
DGND
G1
G2
DGND
-
C.4
CN204
Card Reader Connector (8-Pin)
Table C-4 Card Reader Connector pin assignments (8-Pin)
Pin No.
1
Signal Name
+V3S
I/O Pin No.
Signal Name
+V3S
I/O
-
-
O
I
2
4
CLK_IC_CARDREADE
R
3
DGND
-
5
7
LED_CARDREADER
6
8
DGND
USB_P_CARDREADER
DGND
-
I/O
-
USB_N_CARDREADER I/O
G1
DGND
-
G2
C.5
CN205
LED Connector (20-Pin)
Table C-5 LED Connector pin assignments (20-Pin)
Pin No.
Signal Name
+V5S
I/O Pin No.
Signal Name
KILL_SWCH#
WIMAX_3G_LED#
LED_CARDREADER
+V3A
I/O
I
1
3
5
7
9
-
2
4
WIRELESS_LED#
+V3S
O
-
O
O
-
6
LED_3S_SATA#
EC_PWR_OLED#
O
O
8
10
PWR_BLED#
O
C-4
Satellite E200/205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Apx. C Pin Assignments
11
13
15
17
19
G1
BAT_OLED#
BAT_BLED1#
+V5A
O
O
-
12
14
16
18
20
G2
+V3LA
DCIN_BLED#
+V5LA
-
O
-
DGND
-
DGND
-
DGND
-
DGND
-
DGND
-
DGND
-
C.6
CN208
Internal Micro Phone Connector (2-Pin))
Table C-6 Internal Micro Phone Connector pin assignments (2-Pin)
Pin No.
Signal Name
MIC_IN
I/O Pin No.
Signal Name
DGND
I/O
1
I
2
-
-
G1
DGND
-
G2
DGND
C-7
CN209
Finger Print BD Connect (4-Pin)
Table C-7 Finger Print Board Connect pin assignments (4-Pin)
Pin No.
Signal Name
+V3S
I/O Pin No.
Signal Name
USB_N_FP
DGND
I/O
I/O
-
1
3
-
I/O
-
2
4
USB_P_FP
DGND
G1
G2
DGND
-
C.8
CN250
keyboard cable connector (34-Pin)
Table C-8 keyboard cable connector pin assignments (34-Pin)
Pin No.
Signal Name
I/O Pin No.
Signal Name
SCAN_OUT(16)
SCAN_OUT(17)
+V3S
I/O
1
3
+V3S
-
-
-
I
2
4
I
I
-
I
I
I
-
5
-
6
7
SCAN_OUT(4)
SCAN_OUT(13)
SCAN_OUT(1)
8
SCAN_OUT(2)
SCAN_OUT(15)
SCAN_OUT(0)
9
I
10
12
11
I
Satellite E200/205 Maintenance Manual
C-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Apx. C Pin Assignments
13
15
17
19
21
23
25
27
29
31
SCAN_OUT(11)
SCAN_OUT(5)
SCAN_OUT(10)
SCAN_OUT(8)
SCAN_OUT(7)
SCAN_IN(7)
SCAN_IN(3)
SCAN_IN(0)
SCAN_IN(6)
+V3S
I
I
14
16
18
20
22
24
26
28
30
32
34
G2
SCAN_OUT(9)
SCAN_OUT(6)
SCAN_OUT(14)
SCAN_OUT(12)
SCAN_OUT(3)
SCAN_IN(2)
SCAN_IN(4)
SCAN_IN(5)
SCAN_IN(1)
CAPS_LED#_3
NUM_LED#_3
DGND
I
I
I
I
I
I
I
I
O
O
O
O
-
O
O
O
O
I
33
SCROLL_LED#_3
DGND
I
I
G1
-
-
C.9
CN251
Hot key BD Connector (4-Pin)
Table C-9 Hot key BD Connector pin assignments (4-Pin)
Pin No.
Signal Name
DGND
I/O Pin No.
Signal Name
DGND
I/O
-
1
3
-
I
2
4
KBLED_ID
DGND
+KB_LED_V5S
DGND
O
-
G1
-
G2
C.10
CN280
Touchpad Connector (6-Pin)
Table C-10 Touchpad Connector pin assignments (6-Pin)
Pin No.
Signal Name
+V5S
I/O Pin No.
Signal Name
IM_CLK_5
LEFT_TP
DGND
I/O
1
3
-
I/O
I
2
4
I/O
IM_DAT_5
RIGHT_TP
DGND
I
-
-
5
6
G1
-
G2
DGND
C-6
Satellite E200/205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Apx. C Pin Assignments
C.11
CN281
Touchpad ON/OFF Connector (4-Pin)
Table C-11 Touchpad ON/OFF Connector pin assignments (4-Pin)
Pin No.
Signal Name
+V5S
I/O Pin No.
Signal Name
TP_ON_LED#
DGND
I/O
1
3
-
I
2
4
I
-
-
TP_ON#
DGND
G1
-
G2
DGND
C.12
CN470
RJ45 LAN Port Connector (12-Pin)
Table C-12 RJ45 LAN Port Connector pin assignments (12-Pin)
Pin No.
Signal Name
CGND
I/O Pin No.
Signal Name
CGND
I/O
1
3
-
I
I
I
-
I
-
2
4
-
I
I
I
-
I
-
LAN_TDP
LAN_RDP
LAN_RDN
-
LAN_TDN
LAN_45
5
6
7
8
LAN_78
9
10
12
G2
+V3_LAN
11
G1
LED_R3S_LANLINK#
DGND
LED_R3S_LANACT
DGND
C.13
CN1300
Wireless LAN Module Connector (52-Pin)
Table C-13 Wireless LAN Module Connector pin assignments (52-Pin)
Pin No.
Signal Name
-
I/O Pin No.
Signal Name
+V3S
I/O
-
1
3
-
I/O
I/O
O
-
2
4
CH_DATA
DGND
-
5
CH_CLK
6
+V1.5S
-
7
CLKREQ_WLAN#
DGND
8
LPC_3S_FRAME#
LPC_3S_AD(3)
LPC_3S_AD(2)
LPC_3S_AD(1)
LPC_3S_AD(0)
DGND
O
O
O
O
O
-
9
10
12
14
16
18
11
13
15
17
CLK_PCIE_WLAN#
CLK_PCIE_WLAN
DGND
O
O
-
PLT_RST#
O
Satellite E200/205 Maintenance Manual
C-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Apx. C Pin Assignments
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
G1
CLK_R_PCI_DEBUG
O
-
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
G2
WXMIT_OFF#
PLT_RST#
+V3S
O
DGND
O
PCIE_C_RXN_WLAN
I
-
PCIE_C_RXP_WLAN
I
DGND
-
DGND
-
+V1.5S
-
DGND
-
PCH_3A_ALERT_CLK
PCH_3A_ALERT_DAT
DGND
I/O
PCIE_C_TXN_WLAN
O
O
-
I/O
PCIE_C_TXP_WLAN
-
DGND
USB_N_WLAN
USB_P_WLAN
DGND
I/O
DGND
-
I/O
+V3S
-
-
I
+V3S
-
WIMAX_LED#
-
DGND
-
-
-
-
-
-
-
-
-
-
-
-
+V1.5S
-
-
DGND
PCI_3S_SERIRQ
DGND
O
-
+V3S
DGND
C.14
CN1401
SIM Card Connector (6-Pin)
Table C-14 SIM Card Connector pin assignments (6-Pin)
Pin No.
P1
Signal Name
UIM_PWR
UIM_CLK
-
I/O Pin No.
Signal Name
UIM_RST
DGND
I/O
O
-
O
I/O
-
P2
P5
P7
G2
P3
P6
UIM_DATA
DGND
-
G1
DGND
-
-
C.15
CN1700
SATA HDD Connector (22-Pin)
Table C-15 SATA HDD Connector pin assignments (22-Pin)
Pin No.
1
Signal Name
DGND
I/O Pin No.
Signal Name
I/O
O
-
2
SATA_C_TXP_HDD
C-8
Satellite E200/205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Apx. C Pin Assignments
3
5
SATA_C_TXN_HDD
O
I
4
6
DGND
-
I
SATA_RXN_HDD
SATA_RXP_HDD
7
DGND
-
-
8
-
-
-
-
-
-
-
-
-
-
9
-
10
12
14
16
18
20
22
G2
-
11
13
15
17
19
21
G1
DGND
DGND
+V5S
DGND
DGND
-
-
DGND
-
+V5S
-
+V5S
-
-
-
-
-
-
DGND
-
DGND
C.16
CN1750
SATA ODD Connector (13-Pin)
Table C-16 SATA ODD Connector pin assignments (13-Pin)
Pin No.
S1
Signal Name
DGND
I/O Pin No.
Signal Name
I/O
-
O
I
S2
S4
S6
P1
P3
P5
-
SATA_C_TXP_ODD
O
-
S3
SATA_C_TXN_ODD
SATA_RXN_ODD
DGND
DGND
S5
SATA_RXP_ODD
I
S7
-
-
+V5S_ODD
DGND
-
-
P2
+V5S_ODD
-
-
-
P4
-
-
P6
DGND
-
-
G1
DGND
-
G2
DGND
-
C.17
CN1800
e-SATA Port Connector (11-Pin)
Table C-17 e-SATA Port Connector pin assignments (11-Pin)
Pin No.
Signal Name
+USB_VCC0
USB_L_P_P1
I/O Pin No.
Signal Name
USB_L_N_P1
DGND
I/O
I/O
-
1
3
-
2
4
I/O
SATA_IC_C_TXP_ESAT
A
5
7
DGND
-
6
8
O
-
SATA_IC_C_TXN_ESAT
O
DGND
Satellite E200/205 Maintenance Manual
C-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Apx. C Pin Assignments
A
9
SATA_RXN_ESATA
DGND
I
-
-
-
10
-
SATA_RXP_ESATA
I
-
-
-
11
G1
G3
-
DGND
G2
G4
DGND
DGND
DGND
C.18
CN2000
USB#0 Connector (4-Pin)
Table C-18 USB#0 Connector pin assignments (4-Pin)
Pin No.
Signal Name
+USB_VCC0
USB_L_P_P0
DGND
I/O Pin No.
Signal Name
USB_L_N_P0
DGND
I/O
1
3
-
I/O
-
2
4
I/O
-
-
-
P1
G1
P2
G2
DGND
DGND
-
DGND
C.19
CN2150
Bluetooth Cable Connector (10-Pin)
Table C-19 Bluetooth Cable Connector pin assignments (10-Pin)
Pin No.
Signal Name
USB_P_BT
USB_N_BT
BTMDL#
+V3S
I/O Pin No.
Signal Name
DGND
I/O
1
3
I/O
2
4
-
I/O
I
I/O
CH_CLK
BT_RESET#
CH_DATA
DGND
5
I
-
I
6
7
8
I/O
-
9
BTIFON#
DGND
10
G2
G1
-
DGND
-
C.20
CN2250
Camera Cable Connector (5-Pin)
Table C-20 Camera Cable Connector pin assignments (5-Pin)
Pin No.
Signal Name
+V5S
I/O Pin No.
Signal Name
USB_N_CAM
DGND
I/O
I/O
-
1
3
-
2
4
USB_P_CAM
I/O
C-10
Satellite E200/205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Apx. C Pin Assignments
5
DGND
DGND
-
-
-
-
-
-
G1
G2
DGND
C.21
CN3000
LCD Cable Connector (40-Pin)
Table C-21 LCD Cable Connector pin assignments (40-Pin)
Pin No.
1
Signal Name
DGND
I/O Pin No.
Signal Name
LCM_VDDEN
LCM_VDDEN
+V3S
I/O
O
O
-
2
4
-
-
3
DGND
5
DGND
6
-
7
LVDS_TXDL0N
LVDS_TXDL0P
LVDS_TXDL2N
LVDS_TXDL2P
DGND
8
LVDS_TXDL1N
LVDS_TXDL1P
LVDS_TXCLN
LVDS_TXCLP
DGND
O
O
O
O
-
O
O
O
O
-
9
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
G2
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
G1
LVDS_TXDU0N
LVDS_TXDU0P
LVDS_TXDU2N
LVDS_TXDU2P
DGND
O
O
O
O
-
LVDS_TXDU1N
LVDS_TXDU1P
LVDS_TXCUN
LVDS_TXCUP
DGND
O
O
O
O
-
LVDS_R_DDCCLK
+V5A
I/O
-
LVDS_R_DDCDATA
+V5A
I/O
-
+V5A
-
+V5A
-
+LCM_VBAT
DGND
-
+LCM_VBAT
+LCM_VBAT
DGND
-
O
-
-
DGND
-
INV_PWM_3
DGND
O
-
LCM_BKLTEN
DGND
O
-
C.22
CN3050
RGB Connector (14-Pin)
Table C-22 RGB Connector pin assignments (14-Pin)
Pin No.
Signal Name
I/O Pin No.
Signal Name
I/O
Satellite E200/205 Maintenance Manual
C-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Apx. C Pin Assignments
1
3
+VDD_CRT2
DGND
DGND
DGND
DGND
-
-
2
4
CRTR_R
CRTG_R
O
O
O
O
O
I/O
-
-
5
-
6
CRTB_R
7
-
-
8
CRT_VSYNC_OUT
CRT_HSYNC_OUT
CRT_DDCDATA_OUT
-
9
10
12
14
G2
11
-
13
CRT_DDCCLK_OUT
DGND
I/O
-
G1
DGND
-
C.23
CN3150
HDMI Port Connector (19-Pin))
Table C-23 HDMI Port Connector pin assignments (19-Pin)
Pin No.
1
Signal Name
HDMI_L_TX2P
HDMI_L_TX2N
DGND
I/O Pin No.
Signal Name
DGND
I/O
-
O
O
-
2
4
3
HDMI_L_TX1P
HDMI_L_TX1N
DGND
O
O
-
5
6
7
HDMI_L_TX0P
HDMI_L_TX0N
DGND
O
O
-
8
9
10
12
14
16
18
-
HDMI_L_TXCP
HDMI_L_TXCN
-
O
O
-
11
13
15
17
19
G1
G3
HDMI_CEC
HDMI_DDCCLK_CN
DGND
I/O
O
-
HDMI_DDCDATA_CN
+HDMI_VDD2
-
O
-
HDMI_HPD_5R
DGND
I
-
-
G2
G4
DGND
-
DGND
-
DGND
-
C.24
CN4100
DDR3 So-DImm0 Connector (204-Pin)
Table C-24 DDR3 So-DImm0 Connector pin assignments (204-Pin)
Pin No.
Signal Name
+M_VREF
DGND
I/O Pin No.
Signal Name
DGND
I/O
-
1
3
5
-
-
2
4
6
M_A_DQ(4)
M_A_DQ(5)
I/O
I/O
M_A_DQ(0)
I/O
C-12
Satellite E200/205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Apx. C Pin Assignments
7
M_A_DQ(1)
DGND
I/O
-
8
DGND
M_A_DQS#(0)
M_A_DQS(0)
DGND
-
O
9
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
64
66
68
70
72
74
76
78
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
61
63
65
67
69
71
73
75
77
M_A_DM(0)
DGND
O
O
-
-
M_A_DQ(2)
M_A_DQ(3)
DGND
I/O
I/O
-
M_A_DQ(6)
M_A_DQ(7)
DGND
I/O
I/O
-
M_A_DQ(8)
M_A_DQ(9)
DGND
I/O
I/O
-
M_A_DQ(12)
M_A_DQ(13)
DGND
I/O
I/O
-
M_A_DQS#(1)
M_A_DQS(1)
DGND
O
M_A_DM(1)
DDR3_DRAMRST#
DGND
O-
I
O
-
-
M_A_DQ(10)
M_A_DQ(11)
DGND
I/O
I/O
-
M_A_DQ(14)
M_A_DQ(15)
DGND
I/O
I/O
-
M_A_DQ(16)
M_A_DQ(17)
DGND
I/O
I/O
-
M_A_DQ(20)
M_A_DQ(21)
DGND
I/O
I/O
-
M_A_DQS#(2)
M_A_DQS(2)
DGND
O
M_A_DM(2)
DGND
O
O
-
-
M_A_DQ(22)
M_A_DQ(23)
DGND
I/O
I/O
-
M_A_DQ(18)
M_A_DQ(19)
DGND
I/O
I/O
-
M_A_DQ(28)
M_A_DQ(29)
DGND
I/O
I/O
-
M_A_DQ(24)
M_A_DQ(25)
DGND
I/O
I/O
-
M_A_DQS#(3)
M_A_DQS(3)
DGND
O
M_A_DM(3)
DGND
O
O
-
-
M_A_DQ(26)
M_A_DQ(27)
DGND
I/O
I/O
-
M_A_DQ(30)
M_A_DQ(31)
DGND
I/O
I/O
-
M_CKE0
O
M_CKE1
O
+V1.5
-
+V1.5
-
-
-
M_A_A(15)
I/O
Satellite E200/205 Maintenance Manual
C-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Apx. C Pin Assignments
79
81
M_A_BS2
+V1.5
O
-
80
82
M_A_A(14)
+V1.5
I/O
-
83
M_A_A(12)
M_A_A(9)
+V1.5
I/O
I/O
-
84
M_A_A(11)
M_A_A(7)
+V1.5
I/O
I/O
-
85
86
87
88
89
M_A_A(8)
M_A_A(5)
+V1.5
I/O
I/O
-
90
M_A_A(6)
M_A_A(4)
+V1.5
I/O
I/O
-
91
92
93
94
95
M_A_A(3)
M_A_A(1)
+V1.5
I/O
I/O
-
96
M_A_A(2)
M_A_A(0)
+V1.5
I/O
I/O
-
97
98
99
100
102
104
106
108
110
112
114
116
118
120
122
124
126
128
130
132
134
136
138
140
142
144
146
148
150
101
103
105
107
109
111
113
115
117
119
121
123
125
127
129
131
133
135
137
139
141
143
145
147
149
M_CLK_DDR0
M_CLK_DDR#0
+V1.5
O
M_CLK_DDR1
M_CLK_DDR#1
+V1.5
O
O
O
-
-
M_A_A(10)
M_A_BS0
+V1.5
I/O
O
M_A_BS1
M_A_RAS#
+V1.5
O
O
-
-
M_A_WE#
M_A_CAS#
+V1.5
O
M_CS#0
M_ODT0
+V1.5
O
O
O
-
-
M_A_A(13)
M_CS#1
I/O
O
M_ODT1
-
O
-
+V1.5
-
+V1.5
-
-
-
M_VREF
-
DGND
-
DGND
-
M_A_DQ(32)
M_A_DQ(33)
DGND
I/O
I/O
-
M_A_DQ(36)
M_A_DQ(37)
DGND
I/O
I/O
-
M_A_DQS#(4)
M_A_DQS(4)
DGND
O
M_A_DM(4)
DGND
O
O
-
-
M_A_DQ(38)
M_A_DQ(39)
DGND
I/O
I/O
-
M_A_DQ(34)
M_A_DQ(35)
DGND
I/O
I/O
-
M_A_DQ(44)
M_A_DQ(45)
DGND
I/O
I/O
-
M_A_DQ(40)
M_A_DQ(41)
I/O
I/O
C-14
Satellite E200/205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Apx. C Pin Assignments
151
153
155
157
159
161
163
165
167
169
171
173
175
177
179
181
183
185
187
189
191
193
195
197
199
201
203
G1
DGND
M_A_DM(5)
DGND
I/O
O
152
154
156
158
160
162
164
166
168
170
172
174
176
178
180
182
184
186
188
190
192
194
196
198
200
202
204
G2
M_A_DQS#(5)
M_A_DQS(5)
DGND
O
O
-
-
M_A_DQ(42)
M_A_DQ(43)
DGND
I/O
I/O
-
M_A_DQ(46)
M_A_DQ(47)
DGND
I/O
I/O
-
M_A_DQ(48)
M_A_DQ(49)
DGND
I/O
I/O
-
M_A_DQ(52)
M_A_DQ(53)
DGND
I/O
I/O
-
M_A_DQS#(6)
M_A_DQS(6)
DGND
O
M_A_DM(6)
DGND
O
O
-
I/O
I/O
I/O
-
M_A_DQ(54)
M_A_DQ(55)
DGND
I/O
I/O
-
M_A_DQ(50)
M_A_DQ(51)
DGND
M_A_DQ(60)
M_A_DQ(61)
DGND
I/O
I/O
-
M_A_DQ(56)
M_A_DQ(57)
DGND
I/O
I/O
-
M_A_DQS#(7)
M_A_DQS(7)
DGND
O
M_A_DM(7)
DGND
O
O
-
-
M_A_DQ(58)
M_A_DQ(59)
DGND
I/O
-
M_A_DQ(62)
M_A_DQ(63)
DGND
I/O
I/O
-
-
SA0_DIM0
+V3S
I
PM_EXTTS#1_R
PCH_3S_SMDATA
PCH_3S_SMCLK
+V0.75S
I
-
O
SA1_DIM0
+V0.75S
I
O
-
-
DGND
-
DGND
-
C.25
CN4101 DDR3 So-DImm1 Connector (204-Pin)
Table C-25 DDR3 So-DImm1 Connector pin assignments (204-Pin)
Pin No.
Signal Name
+M_VREF
DGND
I/O Pin No.
Signal Name
DGND
I/O
-
1
3
-
-
2
4
M_B_DQ(4)
I/O
Satellite E200/205 Maintenance Manual
C-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Apx. C Pin Assignments
5
M_B_DQ(0)
M_B_DQ(1)
DGND
I/O
I/O
-
6
M_B_DQ(5)
DGND
I/O
-
7
8
9
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
64
66
68
70
72
74
76
M_B_DQS#(0)
M_B_DQS(0)
DGND
O
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
61
63
65
67
69
71
73
75
M_B_DM(0)
DGND
O
O
-
-
M_B_DQ(2)
M_B_DQ(3)
DGND
I/O
I/O
-
M_B_DQ(6)
M_B_DQ(7)
DGND
I/O
I/O
-
M_B_DQ(8)
M_B_DQ(9)
DGND
I/O
I/O
-
M_B_DQ(12)
M_B_DQ(13)
DGND
I/O
I/O
-
M_B_DQS#(1)
M_B_DQS(1)
DGND
O
M_B_DM(1)
DDR3_DRAMRST#
DGND
-O
I
O
-
-
M_B_DQ(10)
M_B_DQ(11)
DGND
I/O
I/O
-
M_B_DQ(14)
M_B_DQ(15)
DGND
I/O
I/O
-
M_B_DQ(16)
M_B_DQ(17)
DGND
I/O
I/O
-
M_B_DQ(20)
M_B_DQ(21)
DGND
I/O
I/O
-
M_B_DQS#(2)
M_B_DQS(2)
DGND
O
M_B_DM(2)
DGND
O
O
-
-
M_B_DQ(22)
M_B_DQ(23)
DGND
I/O
I/O
-
M_B_DQ(18)
M_B_DQ(19)
DGND
I/O
I/O
-
M_B_DQ(28)
M_B_DQ(29)
DGND
I/O
I/O
-
M_B_DQ(24)
M_B_DQ(25)
DGND
I/O
I/O
-
M_B_DQS#(3)
M_B_DQS(3)
DGND
O
M_B_DM(3)
DGND
O
O
-
-
M_B_DQ(26)
M_B_DQ(27)
DGND
I/O
I/O
-
M_B_DQ(30)
M_B_DQ(31)
DGND
I/O
I/O
-
M_CKE2
O
M_CKE3
O
+V1.5
-
+V1.5
-
C-16
Satellite E200/205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Apx. C Pin Assignments
77
79
-
-
O
78
80
M_B_A(15)
M_B_A(14)
+V1.5
I/O
I/O
-
M_B_BS2
+V1.5
81
-
82
83
M_B_A(12)
M_B_A(9)
+V1.5
I/O
I/O
-
84
M_B_A(11)
M_B_A(7)
+V1.5
I/O
I/O
-
85
86
87
88
89
M_B_A(8)
M_B_A(5)
+V1.5
I/O
I/O
-
90
M_B_A(6)
M_B_A(4)
+V1.5
I/O
I/O
O
91
92
93
94
95
M_B_A(3)
M_B_A(1)
+V1.5
I/O
I/O
-
96
M_B_A(2)
M_B_A(0)
+V1.5
I/O
I/O
-
97
98
99
100
102
104
106
108
110
112
114
116
118
120
122
124
126
128
130
132
134
136
138
140
142
144
146
148
101
103
105
107
109
111
113
115
117
119
121
123
125
127
129
131
133
135
137
139
141
143
145
147
M_CLK_DDR2
M_CLK_DDR#2
+V1.5
O
M_CLK_DDR3
M_CLK_DDR#3
+V1.5
O
O
O
-
-
M_B_A(10)
M_B_BS0
+V1.5
I/O
O
M_B_BS1
M_B_RAS#
+V1.5
O
O
-
-
M_B_WE#
M_B_CAS#
+V1.5
O
M_CS#2
M_ODT2
+V1.5
O
O
O
-
-
M_B_A(13)
M_CS#3
+V1.5
I/O
O
M_ODT3
-
O
-
-
+V1.5
-
-
I/O
-
M_VREF
-
DGND
DGND
-
M_B_DQ(32)
M_B_DQ(33)
DGND
I/O
I/O
-
M_B_DQ(36)
M_B_DQ(37)
DGND
I/O
I/O
-
M_B_DQS#(4)
M_B_DQS(4)
DGND
O
M_B_DM(4)
DGND
O
O
-
-
M_B_DQ(38)
M_B_DQ(39)
DGND
I/O
I/O
-
M_B_DQ(34)
M_B_DQ(35)
DGND
I/O
I/O
-
M_B_DQ(44)
M_B_DQ(45)
I/O
I/O
M_B_DQ(40)
I/O
Satellite E200/205 Maintenance Manual
C-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Apx. C Pin Assignments
149
151
153
155
157
159
161
163
165
167
169
171
173
175
177
179
181
183
185
187
189
191
193
195
197
199
201
203
G1
M_B_DQ(41)
DGND
I/O
-
150
152
154
156
158
160
162
164
166
168
170
172
174
176
178
180
182
184
186
188
190
192
194
196
198
200
202
204
G2
DGND
M_B_DQS#(5)
M_B_DQS(5)
DGND
-
O
M_B_DM(5)
DGND
O
O
-
-
M_B_DQ(42)
M_B_DQ(43)
DGND
I/O
I/O
-
M_B_DQ(46)
M_B_DQ(47)
DGND
I/O
I/O
-
M_B_DQ(48)
M_B_DQ(49)
DGND
I/O
I/O
-
M_B_DQ(52)
M_B_DQ(53)
DGND
I/O
I/O
-
M_B_DQS#(6)
M_B_DQS(6)
DGND
O
M_B_DM(6)
DGND
O
O
-
-
M_B_DQ(54)
M_B_DQ(55)
DGND
I/O
I/O
-
M_B_DQ(50)
M_B_DQ(51)
DGND
I/O
I/O
-
M_B_DQ(60)
M_B_DQ(61)
DGND
I/O
O
M_B_DQ(56)
M_B_DQ(57)
DGND
I/O
I/O
-
-
M_B_DQS#(7)
M_B_DQS(7)
DGND
I/O
O
M_B_DM(7)
DGND
O
-
-
M_B_DQ(58)
M_B_DQ(59)
DGND
I/O
I/O
-
M_B_DQ(62)
M_B_DQ(63)
DGND
I/O
I/O
-
SA0_DIM1
+V3S
I
PM_EXTTS#1_R
PCH_3S_SMDATA
PCH_3S_SMCLK
+V0.75S
I
-
O
SA1_DIM1
+V0.75S
I
O
-
-
DGND
-
DGND
-
C.26
CN4300
FAN Connector (3-Pin)
Table C-26 FAN Connector pin assignments (3-Pin)
Pin No.
1
Signal Name
+FAN_VDD
I/O Pin No.
Signal Name
DGND
I/O
-
-
2
C-18
Satellite E200/205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Apx. C Pin Assignments
3
FAN_TACH1
DGND
-
-
-
-
-
-
G1
G2
DGND
C.27
CN6000
DC-IN Cable Connector (4-Pin)
Table C-27 DC-IN Cable Connector pin assignments (4-Pin)
Pin No.
Signal Name
+VADPTR
DGND
I/O Pin No.
Signal Name
+VADPTR
DGND
I/O
1
3
-
-
2
4
-
-
C.28
CN6970
Battery Connector (9-Pin)
Table C-28 Battery Connector pin assignments (9-Pin)
Pin No.
Signal Name
+VPACK
-
I/O Pin No.
Signal Name
+VPACK
DGND
I/O
1
3
-
-
2
4
-
-
I/O
-
5
THRM1
EC_SMB1_CLK
DGND
I
6
EC_SMB1_DATA
DGND
I/O
-
7
8
9
-
-
-
G1
G3
DGND
-
G2
G4
DGND
-
DGND
-
DGND
-
C.29
CN9400
Touchpad ON/OFF BD Connector (4-Pin)
Table C-29 Touchpad ON/OFF BD Connector pin assignments (4-Pin)
Pin No.
Signal Name
+V5S_SWITCH
GND_SWITCH
GND_SWITCH
I/O Pin No.
Signal Name
+V5S_SWTCH
GND_SWITCH
GND_SWITCH
I/O
1
3
-
-
-
2
4
-
-
-
G1
G2
Satellite E200/205 Maintenance Manual
C-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Apx. C Pin Assignments
C.30
CN9500
LED BD Connector (20-Pin)
Table C-30 LED BD Connector pin assignments (20-Pin)
Pin No.
Signal Name
+V5S_LED
I/O Pin No.
Signal Name
KILL_SWCH#_DB
WIMAX_3G_LED#_DB
LED_CARDREADER_L
+V3A_LED
I/O
O
I
1
3
-
I
-
I
I
I
I
-
-
-
-
2
4
WIRELESS_LED#_DB
+V3S_LED
5
6
I
7
IDE_LED#_L
EC_PWR_OLED#_L
BAT_OLED#_L
BAT_BLED1#_L
+V5A_LED
8
I
9
10
12
14
16
18
20
G2
PWR_BLED#_L
+V3LA+LED
I
11
13
15
17
19
G1
-
DCIN_BLED#_L
+V5LA_LED
I
-
GND_LED
GND_LED
-
GND_LED
GND_LED
-
GND_LED
GND_LED
-
C.31
CN9600
RGB BD Connector (14-Pin)
Table C-31 RGB BD Connector pin assignments (14-Pin)
Pin No.
Signal Name
+VDD_CRT2_DB
GND_CRT
GND_CRT
GND_CRT
GND_CRT
-
I/O Pin No.
Signal Name
CRTR_R_DB
I/O
1
3
-
-
-
-
-
-
2
4
I
I
I
I
I
CRTG_R_DB
5
6
CRTB_R_DB
7
8
CRT_VSYNC_OUT_DB
CRT_HSYNC_OUT_DB
9
10
12
14
G2
11
13
G1
CRT_DDCDATA_OUT_DB I/O
CRT_DDCCLK_OUT_DB I/O
-
-
-
GND_CRT
-
GND_CRT
C.32
CN9601
RGB BD to MB Connector (15-Pin)
Table C-32 RGB BD to MB Connector pin assignments (15-Pin)
Pin No.
Signal Name
I/O Pin No.
Signal Name
I/O
C-20
Satellite E200/205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Apx. C Pin Assignments
1
3
CRTR_R_DB
CRTB_R_DB
GND_CRT
GND_CRT
+VDD_CRT2_DB
-
O
O
-
2
4
CRTG_R_DB
-
O
-
5
6
GND_CRT
GND_CRT
GND_CRT
-
7
-
8
-
9
-
10
12
14
-
-
11
-
CRT_DDCDATA_OUT_DB I/O
13
15
G1
CRT_HSYNC_OUT_DB
O
CRT_VSYNC_OUT_DB
O
-
CRT_DDCCLK_OUT_DB I/O
GND_CRT
-
-
G2
GND_CRT
-
C.33
CN9801 Speaker Connector (4-Pin)
Table C-33 Speaker Connector pin assignments (4-Pin)
Pin No.
Signal Name
SPK_OUT_L+_DB
SPK_OUT_R-_DB
ANAGND
I/O Pin No.
Signal Name
SPK_OUT_L-_DB
SPK_OUT_R+_DB
ANAGND
I/O
O
1
3
O
O
-
2
4
O
G1
G2
-
C.34
CN9802 USB#1 Connector (4-Pin)
Table C-34 USB#1 Connector pin assignments (4-Pin)
Pin No.
Signal Name
+USB_VCC1
USB_L_P_P2
GND_AUDIO
GND_AUDIO
I/O Pin No.
Signal Name
USB_L_N_P2
GND_AUDIO
GND_AUDIO
GND_AUDIO
I/O
1
3
-
I/O
-
2
4
I/O
-
-
-
G1
G3
G2
G4
-
C.35
CN9803 Audio BD Connector (24-Pin)
Table C-35 Audio BD Connector pin assignments (24-Pin)
Pin No.
1
Signal Name
+V5A_DB
I/O Pin No.
Signal Name
+V5A_DB
I/O
-
-
2
Satellite E200/205 Maintenance Manual
C-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Apx. C Pin Assignments
3
5
7
+V5A_DB
+V5A_DB
-
-
4
+V5A_DB
+V3S_CODEC
AMP_SHUTDOWN_DB
AC97_3S_SDIN0_DB
AC97_3S_RST#_DB
GND_AUDIO
-
-
6
+V3S_CODEC
-
8
I
9
AC97_3S_SDOUT_DB
AC97_3S_SYNC_DB
AC97_3S_BITCLK_DB
USB_OC#_1_DB
GND_AUDIO
I
10
12
14
16
18
20
22
24
G2
O
I
11
13
15
17
19
21
23
G1
I
I
-
O
-
SB_USB_1_DB
USB_P_P2_DB
GND_AUDIO
I
I/O
-
USB_N_P2_DB
I/O
I
MMB_BEEP_DB
GND_AUDIO
PCSPKR_DB
I
-
MIC_IN_DB
I
GND_AUDIO
-
GND_AUDIO
-
C.36
CN9900 Card Reader BD Connector (38-Pin)
Table C-36 Card Reader BD Connector pin assignments (38-Pin)
Pin No.
1
Signal Name
SD_WP_MS_CLK
SD_D1
I/O Pin No.
Signal Name
MS_INS#
I/O
I/O
I/O
I/O
I/O
I/O
I/O
-
I/O
I/O
I/O
I/O
I/O
I/O
-
2
3
4
SD_D0_MS_D7
SD_CD#
5
SD_D7_MS_D3
SD_D6_MS_D6
SD_D5_MS_D0
SD_D3_MS_D1
GND_CARD
6
7
8
SD_CLK_MS_D2
SD_D2_MS_D5
SD_CMD
9
10
12
14
16
18
20
22
24
26
28
30
32
34
36
11
13
15
17
19
21
23
25
27
29
31
33
35
+CARD_3V3
SD_D7_MS_D3
SD_CLK_MS_D2
SD_D3_MS_D1
GND_CARD
SD_CLK_MS_D2
SD_CMD
SD_WP_MS_CLK
MS_INS#
I/O
I/O
I/O
I/O
-
I/O
I/O
I/O
-
SD_D5_MS_D0
MS_BS
+CARD_3V3
SD_D0_MS_D7
SD_D4_MS_D4
SD_D1
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
-
SD_D3_MS_D1
SD_D2_MS_D5
XD_D7
MS_BS
+CARD_3V3
SD_WP_MS_CLK
XD_CD#
I/O
SD_CD#
C-22
Satellite E200/205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Apx. C Pin Assignments
37
GND_CARD
-
38
GND_CARD
-
C.37
CN9903 Card Reader BD to MB Connector (8-Pin)
Table C-37 Card Reader BD to MB Connector pin assignments (8-Pin)
Pin No.
Signal Name
+V3S_CARD
I/O Pin No.
Signal Name
+V3S_CARD
GND_CARD
GND_CARD
I/O
1
3
5
-
I
2
4
6
-
-
-
CLK_R_CARDREADER_DB
LED_CARDREADER_DB
O
USB_N_CARDREADER_D
B
USB_P_CARDREADER_D
B
7
I
-
8
I
-
G1
GND_CARD
G2
GND_CARD
C.38
JACK9800 SPDIF/ Head Phone Connector (6-Pin)
Table C-38 SPDIF/ Head Phone Connector pin assignments (6-Pin)
Pin No.
Signal Name
ANAGND
HP_R
I/O Pin No.
Signal Name
HP_L
I/O
O
I
1
3
-
O
-
2
4
HPS
5
ANAGND
ANAGND
6
-
-
G1
-
G2
ANAGND
-
C.39
JACK9801 External MIC Connector (6-Pin)
Table C-39 External MIC Connector pin assignments (6-Pin)
Pin No.
Signal Name
-
I/O Pin No.
Signal Name
MIC_L
MICS
I/O
1
3
-
I
2
4
I
I
-
-
MIC_R
MICS
5
I/O
-
6
-
G1
ANAGND
G2
ANAGND
Satellite E200/205 Maintenance Manual
C-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Keyboard Scan/Character Codes
Appendices
Apx. D Keyboard Scan/Character Codes
Appendix D Keyboard Scan/Character Codes
Table D-1 Scan codes (set 1 and set 2) (1/4)
Cap
No.
Code set 1
Code set 2
Break
Note
Keytop
Make
Break
Make
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
‘ ~
1 !
29
02
03
04
05
06
07
08
09
0A
0B
0C
0D
A9
82
83
84
85
86
87
88
89
8A
8B
8C
8D
0E
16
1E
26
25
2E
36
3D
3E
46
45
4E
55
7D
66
0D
15
1D
24
2D
2C
35
3C
43
44
4D
54
5B
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
0E
16
1E
26
25
2E
36
3D
3E
46
45
4E
55
7D
66
0D
15
1D
24
2D
2C
35
3C
43
44
4D
54
5B
2 @
3 #
4 $
5 %
6 ^
7 &
8 *
*2
*2
*2
*2
9 (
0 )
- _
= +
BkSp
Tab
Q
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
8E
8F
90
91
92
93
94
95
96
97
98
99
9A
9B
W
E
R
T
Y
U
*2
*2
*2
*2
I
O
P
[ {
] }
Satellite E200/205 Maintenance Manual
D-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Keyboard Scan/Character Codes
Table D-1 Scan codes (set 1 and set 2) (2/4)
Cap
No.
Code set 1
Code set 2
Break
Note
Keytop
Make
Break
Make
29
30
31
32
33
34
35
36
37
38
39
40
41
\ |
2B
3A
1E
1F
20
21
22
23
24
25
26
27
28
AB
BA
9E
9F
A0
A1
A2
A3
A4
A5
A6
A7
A8
5D
58
1C
1B
23
2B
34
33
3B
42
4B
4C
52
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
5D
58
1C
1B
23
2B
34
33
3B
42
4B
4C
52
*5
Caps Lock
A
S
D
F
G
H
J
*2
*2
*2
*2
K
L
; :
‘ “
43
44
45
Enter
1C
2A
56
9C
AA
D6
5A
12
61
F0
F0
F0
5A
12
61
*3
Shift (L)
No.102
key
46
47
48
49
50
51
52
53
54
55
56
Z
X
2C
2D
2E
2F
30
31
32
33
34
35
AC
AD
AE
AF
B0
B1
B2
B3
B4
B5
1A
22
21
2A
32
31
3A
41
49
4A
73
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
1A
22
21
2A
32
31
3A
41
49
4A
73
C
V
B
N
M
*2
*2
*2
*2
, <
. >
/ ?
\_
57
Shift (R)
36
B6
59
F0
59
D-2
Satellite E200/205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Keyboard Scan/Character Codes
Appendices
Table D-1 Scan codes (set 1 and set 2) (3/4)
Cap
No.
Code set 1
Code set 2
Break
Note
Keytop
Make
Break
Make
58
Ctrl
1D
9D
14
F0
14
*3
*3
60
61
62
Alt (L)
Space
38
39
B8
B9
11
29
F0
F0
11
29
11
ALT (R)
E0 38
E0 B8 E0 11
E0
F0
75
76
Ins
E0 52
E0 53
E0 D2 E0 70
E0 D3 E0 71
E0
E0
F0
F0
70
71
*1
*1
Del
79
80
81
E0 4B E0 CB E0 6B E0
F0
F0
F0
6B
6C
69
*1
*1
*1
Home
End
E0 47
E0 4F
E0 C7 E0 6C E0
E0 CF E0 69
E0
83
84
85
86
E0 48
E0 50
E0 49
E0 51
E0 C8 E0 75
E0 D0 E0 72
E0
E0
F0
F0
F0
F0
75
72
7D
7A
*1
*1
*1
*1
PgUp
PgDn
E0 C9 E0 7D E0
E0 D1 E0 7A E0
89
E0 4D E0 CD E0 74
E0
F0
74
*1
110
112
113
114
115
116
117
118
119
120
121
Esc
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
01
3B
3C
3D
3E
3F
40
41
42
43
44
81
BB
BC
BD
BE
BF
C0
C1
C2
C3
C4
76
05
06
04
0C
03
0B
83
0A
01
09
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
76
05
06
04
0C
03
0B
83
0A
01
09
*3
Satellite E200/205 Maintenance Manual
D-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Keyboard Scan/Character Codes
Table D-1 Scan codes (set 1 and set 2) (4/4)
Cap
No.
Code set 1
Make Break
Code set 2
Break
Note
Keytop
F11
Make
122
123
124
57
58
D7
D8
*6
78
7
F0
F0
*6
78
7
*3
F12
*3
*6
PrintSc *6
*6
126
Pause *7
*7
*7
*7
*7
*4
202
203
204
205
206
207
Fn
Win
—
—
—
—
E0
E0
5B
5D
E0
E0
DB
DD
E0
E0
70
79
7B
1F
2F
E0
E0
F0
F0
F0
F0
F0
70
79
7B
1F
2F
App
Kat/Hir
Hen
*8
*8
*8
Muh
Notes:
1. * Scan codes differ by mode.
2. * Scan codes differ by overlay function.
3. * Combination with the Fn key makes different codes.
4. * Fn key does not generate a code by itself.
5. * This key corresponds to key No. 42 in a 102-key model.
6. * Refer to Table D-6, No. 124 key scan code.
7. * Refer to Table D-7, No. 126 key scan code.
8. * 205~207 are for JAPAN keyboard only
D-4
Satellite E200/205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Keyboard Scan/Character Codes
Appendices
Table D-2 Scan codes with left Shift key
Cap
No.
Key
top
Code set 1
Code set 2
Make
Break
Make
Break
55
75
76
79
80
81
83
84
85
86
89
203
204
/
E0 AA E0 35 E0 B5 E0 2A E0 F0 12 E0 4A E0 F0 4A E0 12
E0 AA E0 52 E0 D2 E0 2A E0 F0 12 E0 70 E0 F0 70 E0 12
E0 AA E0 53 E0 D3 E0 2A E0 F0 12 E0 71 E0 F0 71 E0 12
E0 AA E0 4B E0 CB E0 2A E0 F0 12 E0 6B E0 F0 6B E0 12
INS
DEL
Home E0 AA E0 47 E0 C7 E0 2A E0 F0 12 E0 6C E0 F0 6C E0 12
End
E0 AA E0 4F E0 CF E0 2A E0 F0 12 E0 69 E0 F0 69 E0 12
E0 AA E0 48 E0 C8 E0 2A E0 F0 12 E0 75 E0 F0 75 E0 12
E0 AA E0 50 E0 D0 E0 2A E0 F0 12 E0 72 E0 F0 72 E0 12
PgUp E0 AA E0 49 E0 C9 E0 2A E0 F0 12 E0 7D E0 F0 7D E0 12
PgDn E0 AA E0 51 E0 D1 E0 2A E0 F0 12 E0 7A E0 F0 7A E0 12
E0 AA E0 4D E0 CD E0 2A E0 F0 12 E0 74 E0 F0 74 E0 12
E0 AA E0 5B E0 DB E0 2A E0 F0 12 E0 1F E0 F0 1F E0 12
E0 AA E0 5D E0 DD E0 2A E0 F0 12 E0 2F E0 F0 2F E0 12
Win
App
Note : The table above shows scan codes with the left Shift key. In combination with the
right Shift key, scan codes are changed as listed below:
With left Shift
With right Shift
Set 1
Set 2
E0 AA __________ E0 B6
E0 2A ___________ E0 36
E0 F0 12 ________ E0 F0 59
E0 12 ___________ E0 59
Satellite E200/205 Maintenance Manual
D-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Keyboard Scan/Character Codes
Table D-3 Scan codes in Numlock mode
Cap
Key
top
Code set 1
Code set 2
No.
Make
Break
Make
Break
75
76
INS
DEL
E0 2A E0 52 E0 D2 E0 AA E0 12 E0 70 E0 F0 70 E0 F0 12
E0 2A E0 53 E0 D3 E0 AA E0 12 E0 71 E0 F0 71 E0 F0 12
E0 2A E0 4B E0 CB E0 AA E0 12 E0 6B E0 F0 6B E0 F0 12
79
80
Home E0 2A E0 47 E0 C7 E0 AA E0 12 E0 6C E0 F0 6C E0 F0 12
81
End
E0 2A E0 4F E0 CF E0 AA E0 12 E0 69 E0 F0 69 E0 F0 12
E0 2A E0 48 E0 C8 E0 AA E0 12 E0 75 E0 F0 75 E0 F0 12
E0 2A E0 50 E0 D0 E0 AA E0 12 E0 72 E0 F0 72 E0 F0 12
83
84
85
PgUp E0 2A E0 49 E0 C9 E0 AA E0 12 E0 7D E0 F0 7D E0 F0 12
PgDn E0 2A E0 51 E0 D1 E0 AA E0 12 E0 7A E0 F0 7A E0 F0 12
86
89
E0 2A E0 4D E0 CD E0 AA E0 12 E0 74 E0 F0 74 E0 F0 12
E0 2A E0 5B E0 DB E0 AA E0 12 E0 1F E0 F0 1F E0 F0 12
E0 2A E0 5D E0 DD E0 AA E0 12 E0 2F E0 F0 2F E0 F0 12
Win
App
203
204
Table D-4 Scan codes with Fn key
Cap
Code set 1
Make Break
Code set 2
Break
No.
Keytop
Make
5A
43
58
ENT
CTRL
E0
E0
E0
1C
1D
38
E0
E0
E0
9C
9D
B8
E0
E0
E0
E0
E0
E0
F0
F0
F0
5A
14
11
14
11
60
LALT
121
122
123
ARROW
NUMERIC
Scrl
45
45
46
C5
77
77
7E
F0
F0
F0
77
77
7E
C5
C5
D-6
Satellite E200/205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Keyboard Scan/Character Codes
Appendices
Table D-5 Scan codes in overlay mode
Cap
No.
Keytop
Code set 1
Break
Code set 2
Break
Make
47
Make
6C
75
08
09
10
11
23
24
25
26
37
38
39
40
52
54
55
7
8
9
0
U
I
(7)
C7
C8
C9
B7
CB
CC
CD
CA
CF
D0
D1
CE
D2
D3
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
6C
75
7D
7C
6B
73
74
7B
69
72
7A
79
70
71
(8)
(9)
(*)
48
49
7D
7C
6B
73
37
(4)
(5)
(6)
(–)
(1)
(2)
(3)
(+)
(0)
(.)
4B
4C
4D
4A
4F
50
O
P
J
K
L
;
74
7B
69
72
51
7A
79
4E
52
M
.
70
53
71
/
(/)
E0
35
E0
B5
40
4A
E0
F0
4A
Table D-6 No.124 key scan code
Key
top
Shift
Code set 1
Code set 2
Make
Break
Make
Break
Prt Sc Common E0 2A E0 37 E0 B7 E0 AA E0 12 E0 7C E0 F0 7C E0 F0 12
E0 37
E0 37
54
E0 B7
E0 B7
D4
E0 7C
E0 7C
84
E0 F0 7C
E0 F0 7C
F0 B4
Ctrl
Shift
Alt
Satellite E200/205 Maintenance Manual
D-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Keyboard Scan/Character Codes
Table D-7 No.126 key scan code
Key
top
Shift
Code set 1
Make
Code set 2
Make
Pause Common* E1 1D 45 E1 9D C5 E1 14 77 E1 F0 14
Ctrl* E0 46 E0 C6 E0 7E E0 F0 7E
F0 77
*: This key generates only make codes.
D-8
Satellite E200/205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Apx. E Key Layout
Appendices
Apx. E
Key Layout
Appendix E Key Layout
E.1 United States (US) Keyboard
Figure E-1 US keyboard
E.2 Japan (JP) Keyboard
Figure E-2 JP keyboard
Satellite E200/205 Maintenance Manual
E-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Apx E Key Layout
E.3 Korean (KR) Keyboard
Figure E-3 KR keyboard
E.4 Canadian Bilingual (QB) Keyboard
Figure E-4 QB keyboard
E-2
Satellite E200/205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Apx E Key Layout
Appendices
E.5 Taiwan (TC) Keyboard
Figure E-5 TC keyboard
E.6 Thai (TH) Keyboard
Figure E-6 TH keyboard
Satellite E200/205 Maintenance Manual
E-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Apx E Key Layout
E.7 United Kingdom (EN) Keyboard
Figure E-7 EN keyboard
E.8 UK ENGLISH (CB) Keyboard
Figure E-8 TF keyboard
E-4
Satellite E200/205 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
|