MULTIFUNCTIONAL DIGITAL SYSTEMS
Copying Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
„ How to read this manual
Thank you for purchasing TOSHIBA Multifunctional Digital Systems. This manual describes how to use the copying
functions. Read this manual before using this equipment. Keep this manual within easy reach, and use it to configure an
environment that makes the best use of the e-STUDIO’s functions.
This equipment provides the scanning function as an option. However, this optional scanning function is already installed in some
models.
‰ Symbols in this manual
In this manual, some important items are described with the symbols shown below. Be sure to read these items before
using this equipment.
Indicates a potentially hazardous situation which, if not avoided, could result in death, serious
injury, or serious damage, or fire in the equipment or surrounding objects.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate
injury, partial damage to the equipment or surrounding objects, or loss of data.
Indicates information to which you should pay attention when operating the equipment.
Other than the above, this manual also describes information that may be useful for the operation of this equipment with
the following signage:
Describes handy information that is useful to know when operating the equipment.
Pages describing items related to what you are currently doing. See these pages as required.
‰ Description of original/paper direction
Paper or originals of A4, B5 or LT size can be placed either in a portrait direction or in a landscape direction. In this
manual, “-R” is added to this paper size when this size of paper or original is placed in a landscape direction.
Example: A4 size original on the original glass
Placed in a portrait direction: A4
Placed in a landscape direction: A4-R
Paper or originals of A3, B4, LD or LG can only be placed in a landscape direction, therefore “-R” is not added to these
sizes.
‰ Screens
y Screens on this manual may differ from the actual ones depending on how the equipment is used, such as the status
of the installed options.
y The illustration screens used in this manual are for paper in the A/B format. If you use paper in the LT format, the
display or the order of buttons in the illustrations may differ from that of your equipment.
Preface
1
Download from Www.Somanuals.com. All Manuals Search And Download.
‰ Trademarks
The company names and product names in this manual are the trademarks of their respective companies.
2
Preface
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Acceptable copy paper........................................................................................................ 11
Placing paper in drawers..................................................................................................... 13
Placing paper in the External Large Capacity Feeder (optional)......................................... 20
Book-type originals.............................................................................................................. 24
Confirming the set functions................................................................................................ 46
Clearing the set functions.................................................................................................... 47
Restrictions on function combinations................................................................................. 47
Copying mixed-size originals in one operation.................................................................... 50
Sort/Group mode................................................................................................................. 62
CONTENTS
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Rotate sort mode................................................................................................................. 64
Making a 2-sided copy from a book-type original................................................................ 75
Displaying EDIT Menu............................................................................................................ 84
Creating top/bottom margin or left/right margin................................................................... 85
Edge Erase.............................................................................................................................. 89
Image Editing.......................................................................................................................... 99
XY Zoom................................................................................................................................ 103
COPY ON TAB.................................................................................................................. 124
4
CONTENTS
Download from Www.Somanuals.com. All Manuals Search And Download.
Registering Templates......................................................................................................... 141
Registering templates into a private group........................................................................ 145
Confirming Copy Job Status............................................................................................... 158
CONTENTS
5
Download from Www.Somanuals.com. All Manuals Search And Download.
6
CONTENTS
Download from Www.Somanuals.com. All Manuals Search And Download.
1.
BEFORE USING EQUIPMENT
This chapter describes what you need to know before using this equipment, such as the composition of the BASIC menu
for the copying functions and how to place copy paper.
BASIC Menu for the Copier Function..................................................................................... 8
Acceptable copy paper.........................................................................................................................................11
Placing paper in drawers......................................................................................................................................13
Placing paper in the External Large Capacity Feeder (optional)..........................................................................20
Download from Www.Somanuals.com. All Manuals Search And Download.
1 BEFORE USING EQUIPMENT
BASIC Menu for the Copier Function
When a few seconds have passed after you have turned the power ON, the BASIC menu for the copier function appears
on the touch panel. The BASIC menu shows the following information:
19
18
17
16
15
14
1
2
13
12
3
4
5
6
7
8
9
10
11
1. Message indication area
This shows a brief description of the functions or the current status of this equipment in message form.
This shows the size, paper type or amount of paper remaining in each drawer.
These are for switching between the menus of “BASIC”, “EDIT” and “IMAGE”.
4. Alert message indication area
This shows alert messages such as the replacement timing of the toner cartridges.
When this equipment is managed with the user management function and department management function
When this equipment is managed with the user management function and the department management function, the number of
copies available for each user ( ) or department (
) appears here for approx. 5 seconds after user authentication.
y
y
The display may differ depending on the management status of this equipment.
For details of the user management function or the department management function, ask your administrator.
This is for changing the mode to automatic paper selection.
This is for changing the reproduction ratio of images.
This is for selecting simplex/duplex copying (e.g. 1 -> 2-sided, 2 -> 2 sided).
This is for selecting a sorting mode.
This is for selecting an original mode.
10. Date and time
This is for confirming the processing status of copy, fax, scan or print jobs, and also for viewing their performing history.
8
BASIC Menu for the Copier Function
Download from Www.Somanuals.com. All Manuals Search And Download.
1 BEFORE USING EQUIPMENT
1.BEFORE USING EQUIPMENT
12. [PROOF COPY] button (
This is for making a proof copy to check an image before making a large amount of copies.
These are for adjusting the density level of images.
14. Number of copy sets
15. Number of remaining copy sets
16. Help button
This is for viewing the explanation of each function or the buttons on the touch panel.
This is for the template function.
This is for checking currently set functions.
This is for the storage function.
BASIC Menu for the Copier Function
9
Download from Www.Somanuals.com. All Manuals Search And Download.
1 BEFORE USING EQUIPMENT
Equipment status indication area
The equipment status indication area shows the following information:
5
4
1
3
2
1. Receiving tray indication (
This shows the tray to which copied paper exits.
This is for switching receiving (exit) trays.
These show the size of paper, amount of paper remaining in each drawer and the paper type set for the drawer. When
you want to use a particular drawer, press the corresponding button.
When this button is pressed with paper set in the bypass tray, it will be selected as the paper source.
This shows the type of paper placed on the bypass tray with an icon.
10 BASIC Menu for the Copier Function
Download from Www.Somanuals.com. All Manuals Search And Download.
1 BEFORE USING EQUIPMENT
Placing Paper
„ Acceptable copy paper
The following paper can be placed and used for copying.
The values are valid only when Toshiba-recommended paper is used. For the recommended paper, refer to the Quick
Start Guide.
y Do not place paper with mixed sizes or paper types in the same drawer.
y Be sure that the height of the stacked paper does not exceed the line indicated on the guides.
Feeder
Drawers
Paper type
Plain paper
(64 - 80 g/m2)
Maximum sheet capacity
Size
550 sheets (64 g/m2) (17 lb. Bond)
500 sheets (80 g/m2) (20 lb. Bond)
A/B format:
A3, A4, A4-R, A5-R, B4, B5, B5-R,
FOLIO
(17 - 20 lb. Bond)
THICK 1
(81 - 105 g/m2)
(21 - 28 lb. Bond)
400 sheets
200 sheets
150 sheets
—
LT format:
LD, LG, LT, LT-R, ST-R, COMP, 13"LG,
8.5"SQ
THICK 2
(106 - 163 g/m2)
(29 lb. Bond - 90 lb. Index)
K format:
8K, 16K, 16K-R
THICK 3
(164 - 209 g/m2)
(91 - 110 lb. Index)
Tab paper *1, *2, *3
A4, LT
A4, LT
3000 sheets (64 g/m2) (17 lb. Bond)
2500 sheets (80 g/m2) (20 lb. Bond)
Tandem large
capacity feeder
Plain paper
(64 - 80 g/m2)
(17 - 20 lb. Bond)
THICK 1
(81 - 105 g/m2)
(21 - 28 lb. Bond)
2000 sheets
1000 sheets
750 sheets
THICK 2
(106 - 163 g/m2)
(29 lb. Bond - 90 lb. Index)
THICK 3
(164 - 209 g/m2)
(91 - 110 lb. Index)
4500 sheets (64 g/m2) (17 lb. Bond)
4000 sheets (80 g/m2) (20 lb. Bond)
External Large
Capacity Feeder
(optional)
Plain paper
(64 - 80 g/m2)
(17 - 20 lb. Bond)
A4, LT
THICK 1
(81 - 105 g/m2)
(21 - 28 lb. Bond)
3500 sheets
2000 sheets
1500 sheets
THICK 2
(106 - 163 g/m2)
(29 lb. Bond - 90 lb. Index)
THICK 3
(164 - 209 g/m2)
(91 - 110 lb. Index)
Placing Paper 11
Download from Www.Somanuals.com. All Manuals Search And Download.
1 BEFORE USING EQUIPMENT
Feeder
Bypass tray
Paper type
Plain paper
(64 - 80 g/m2)
Maximum sheet capacity
100 sheets
Size
A/B format:
A3, A4, A4-R, A5-R, A6-R *6, B4, B5,
(17 - 20 lb. Bond)
B5-R, FOLIO
THICK 1
(81 - 105 g/m2)
(21 - 28 lb. Bond)
80 sheets
40 sheets
30 sheets
—
LT format:
LD, LG, LT, LT-R, ST-R, COMP, 13"LG,
8.5"SQ
THICK 2
(106 - 163 g/m2)
(29 lb. Bond - 90 lb. Index)
K format:
8K, 16K, 16K-R
THICK 3
(164 - 209 g/m2)
(91 - 110 lb. Index)
Non-standard size:
Length: 100 - 297 mm (3.9" - 11.7"),
Width: 148 - 432 mm (5.8" - 17") *6
Tracing paper *1, *4
(75 g/m2)
(20 lb. Bond)
Sticker labels *1, *5
Tab paper *1, *2, *3
OHP film *1
—
—
A4, LT
A4, LT
30 sheets
*1 Duplex copying is not available.
*2 Tab paper can be set in any drawer other than the External Large Capacity Feeder (optional) or the bypass tray (the 2nd drawer
recommended).
*3 When a finisher (optional) is installed in the equipment, use 5 or 8-tab paper.
*4 For making copies on the tracing paper, select “PLAIN” for the paper type.
*5 For making copies on the sticker labels, select “THICK 3” for the paper type.
*6 If a copy is made on either A6-R or non-standard size paper with a width of less than 182 mm (7.2"), or on paper of an unregistered size, the
paper exits with its copied side up.
y “LT format” is the standard size only for use in North America.
y “K format” is a Chinese standard size.
y Abbreviations for paper sizes: LT: Letter, LD: Ledger, LG: Legal, ST: Statement, COMP: Computer, SQ: Square
‰ Unacceptable copy paper
Do not use the types of paper shown below. This could cause a paper jam.
y Damp paper
y Folded paper
y Curled or creased paper
y Paper whose surface is extremely smooth or rough
Do not use the types of paper shown below. This could cause an equipment malfunction.
y Paper whose surface has had a special treatment
y Paper once printed with other copiers or printers
‰ Precautions for storing copy paper
Make sure of the following when storing copy paper:
y Wrap the paper in its wrapping to keep it free from dust.
y Avoid direct sunlight.
y Store in a damp-free space.
y To prevent paper from being folded or bent, store it in a flat place.
12 Placing Paper
Download from Www.Somanuals.com. All Manuals Search And Download.
1 BEFORE USING EQUIPMENT
1.BEFORE USING EQUIPMENT
„ Placing paper in drawers
Follow the procedure below to place paper in a drawer. For acceptable copy paper, see the following page:
Turn the power of this equipment ON.
1
Pull out a drawer carefully until it comes to a stop.
2
A
Be careful not to touch the slide rails (A in the figure).
This could injure you.
Push the lower part of the end guide in the direction
of the arrows to remove it, then reinstall it at the
position of the desired paper size.
3
4
5
The paper size is indicated on the bottom inner surface of the
drawer.
Push the part shown with an arrow (right side) of the
side guide to unlock it.
While holding the green lever of the side guide in the
direction of the arrow, set the side guide to the
desired paper size.
y The paper size is indicated on the bottom inner surface of the
drawer.
y Adjust the side guides with both hands.
Placing Paper 13
Download from Www.Somanuals.com. All Manuals Search And Download.
1 BEFORE USING EQUIPMENT
Place paper in the drawer.
6
y Up to 550 sheets (64 g/m2) (17 lb. Bond) can be placed in one
drawer. Be sure that the height of the stacked paper does not
exceed the line indicated inside of the side guides.
y Fan and jog the stack of paper well before you place it in a
drawer, or the sheets may not be separated before being fed.
Be careful not to cut your fingers when fanning.
y Place paper with its copy side down. The copy side may be
noted on its wrapping paper.
Adjust the side guides.
7
8
Make sure that a gap (“A” in the figure on the right) of 0.5 mm (0.02")
(1.0 mm (0.04") or less in total) *1 is left between the paper and the side
guide for plain paper. If the gap is inappropriate, it could cause paper
misfeeding.
A
*1 For thick paper, the gap must be 0.5 mm (0.02") to 1.0 mm (0.04") (1.0 mm
(0.04") to 2.0 mm (0.08") in total).
Push the part shown with an arrow (left side) to lock
the side guide.
Change the paper size indicator if required.
9
Push the drawer straight into this equipment carefully until it comes to a stop.
10
Be careful not to let your fingers be caught when pushing the drawer into this equipment.
This could injure you.
14 Placing Paper
Download from Www.Somanuals.com. All Manuals Search And Download.
1 BEFORE USING EQUIPMENT
1.BEFORE USING EQUIPMENT
The menu below appears. When the size or type of paper is different from the one that
was in the drawer, press [YES] on the touch panel. When they are the same, press [NO].
11
y The menu above may not appear depending on the setting of this equipment. In this case, see the following
pages to change the settings of the paper size and paper type:
y If you want to change the setting for displaying this menu, ask your administrator.
If you press [NO], the procedure is completed.
Select the size and type of the paper placed in the drawer on the touch panel.
1) Select the paper size.
3) Press [OK].
12
Placing Paper 15
Download from Www.Somanuals.com. All Manuals Search And Download.
1 BEFORE USING EQUIPMENT
„ Placing paper in the tandem large capacity feeder
Pull out the drawer of the tandem large capacity
feeder carefully until it comes to a stop.
1
A
Be careful not to touch the slide rails (A in the figure).
This could injure you.
A
Place 2 stacks of paper in the right and left trays
correspondingly.
2
Fan and jog the paper well before placing it. Place it with its copy side
down. Place one stack of paper in the right-hand tray (shown as “A” in
the figure) with its side touching the right corner of the tray, and place
the other stack of paper in the left-hand tray (shown as “B” in the figure)
with its side touching the left corner of the tray. Paper can be placed
neatly if you divide stacks into small bundles and pile them up on the
two trays alternately.
A
B
y Paper in the right-hand tray is used first. When it runs out, paper in the left-hand tray will be moved
automatically to the right-hand tray and fed.
y A maximum of 2500 sheets (80 g/m2) (20 lb. Bond) can be placed in the 2 trays. However the stack height
of the paper must not exceed the line indicated inside the side guides.
y The copy side may be noted on its wrapping paper.
y Be careful not to cut your fingers when fanning the paper.
y When placing paper, be sure that the center lever is not open. (See the label attached in the tandem large
capacity feeder.)
Push the drawer of the tandem large capacity feeder straight into this equipment
carefully.
3
When the drawer is completely inserted, the right-hand tray will move up to the paper feeding position.
Be careful not to let your fingers be caught when pushing the drawer into this equipment.
This could injure you.
16 Placing Paper
Download from Www.Somanuals.com. All Manuals Search And Download.
1 BEFORE USING EQUIPMENT
1.BEFORE USING EQUIPMENT
„ Registering paper size
When you place paper for the first time or you replace the paper with that of a different size, you need to register the size
to this equipment.
Press the [USER FUNCTIONS] button on the control
panel.
1
Press the [USER] tab on the touch panel to display the user setting menu, and then
press [DRAWER].
2
Select the paper size on the touch panel.
1) Select the drawer in which you placed paper.
2) Select the paper size.
3
Press the [USER FUNCTIONS] or [COPY] button on the control panel.
The menu returns to the BASIC menu.
4
Placing Paper 17
Download from Www.Somanuals.com. All Manuals Search And Download.
1 BEFORE USING EQUIPMENT
„ Setting paper type
When you place any special paper other than plain paper or that not used for normal copying, you need to set the
thickness and attribute into this equipment.
y The thickness and the attribute can be set together; however, one of “THICK 1” to “THICK 3” and the attribute “TAB
PAPER” cannot be set together. If one of them is set, the other setting will be cleared.
y When the thickness “THICK 1, 2 or 3”, or an attribute other than “NONE” is set for a drawer, the paper placed in this
drawer will not be used for the automatic paper selection mode.
y When an attribute other than “NONE” is set for a drawer, the Automatic Change of Paper Source function (Feeding
the same size of paper from a different drawer even if the specified drawer from which paper is being fed is empty)
is disabled for the paper in this drawer.
For how to set Automatic Change of Paper Source, refer to the MFP Management Guide.
y The set paper type appears on the equipment status indication area with an icon.
Acceptable paper types are as follows:
Thickness
Button
PLAIN
Description
Plain paper: 64 - 80 g/m2 (17 - 20 lb. Bond)
Thick paper
THICK 1: 81 - 105 g/m2 (21 - 28 lb. Bond)
Icon
—
THICK 1 - 3
,
,
THICK 2: 106 - 163 g/m2 (29 lb. Bond - 90 lb. Index)
THICK 3: 164 - 209 g/m2 (91 lb. Index - 110 lb. Index)
Attribute
Button
NONE
Description
Icon
No attribute specified
—
INSERT
Sheets used in the sheet insertion mode
Up to 2 types of sheets (Insertion sheets 1 and 2) can be set. To set Insertion sheet 1
and 2, select the drawer for Insertion sheet 1 and press [INSERT], and then select a
drawer for Insertion sheet 2 and press [INSERT].
,
COVER
Sheets used in the cover sheet mode
SPECIAL
Colored paper or paper with watermarks, etc.
FAX *1, *2
TAB
FAX paper
Tab paper
*1 Fax transmission and reception is available only when the Fax Unit (optional) is installed.
*2 When lists are printed, paper set as “FAX” is used. For printing lists, refer to the MFP Management Guide.
Press the [USER FUNCTIONS] button on the control
panel.
1
18 Placing Paper
Download from Www.Somanuals.com. All Manuals Search And Download.
1 BEFORE USING EQUIPMENT
1.BEFORE USING EQUIPMENT
Press the [USER] tab on the touch panel to display the user setting menu, and then
press [DRAWER].
2
Press [PAPER TYPE].
3
4
Select the paper type.
1) Select the drawer in which you placed paper.
2) Select the paper type.
Press the [USER FUNCTIONS] or [COPY] button on the control panel.
The menu returns to the BASIC menu.
5
Clearing the set paper type
Press the drawer button on the menu in step 4, and then press the paper type whose setting you want to clear.
If both INSERT 1 and INSERT 2 are set and you clear the setting of only INSERT 1, the setting for INSERT 2
automatically becomes the setting for INSERT 1.
Placing Paper 19
Download from Www.Somanuals.com. All Manuals Search And Download.
1 BEFORE USING EQUIPMENT
„ Placing paper in the External Large Capacity Feeder (optional)
Pull out the drawer of the External Large Capacity
Feeder carefully until it comes to a stop.
1
A
Be careful not to touch the slide rails (A in the figure).
This could injure you.
A
Place paper on the tray.
Fan and jog the paper well before placing it on the tray. Place it with its
copy side up. Do not allow any gap between the paper and the rear
side guide.
2
y A maximum of 4500 sheets (64 g/m2) (17 lb. Bond) can be placed. However the stack height of the paper
must not exceed the line indicated on the rear side guide.
y The copy side may be noted on its wrapping paper.
y Be careful not to cut your fingers when fanning the paper.
y Do not allow any gap between the paper and the rear side guide. If there is any gap, the copied image may
be skewed.
Push the drawer of the External Large Capacity Feeder straight into this equipment
carefully.
3
When the drawer is completely inserted, the tray will move up to the paper feeding position.
Be careful not to let your fingers be caught when pushing the drawer into this equipment.
This could injure you.
20 Placing Paper
Download from Www.Somanuals.com. All Manuals Search And Download.
2.
HOW TO MAKE COPIES
This chapter explains the basic copying procedures.
Placing Originals.................................................................................................................... 22
Book-type originals...............................................................................................................................................24
Using the RADF (Reversing Automatic Document Feeder).................................................................................25
Making Copies........................................................................................................................ 28
Basic copying procedure......................................................................................................................................28
Selecting exit tray.................................................................................................................................................35
Bypass copying on standard size paper...............................................................................................................37
Download from Www.Somanuals.com. All Manuals Search And Download.
2 HOW TO MAKE COPIES
Placing Originals
„ Acceptable originals
When the RADF (Reversing Automatic Document Feeder) is used, 2-sided originals can be automatically scanned one
sheet after another. When the original glass is used, originals such as OHP films, tracing paper, booklet or 3-dimensional
objects, that cannot be placed on the RADF can be scanned, as well as plain paper.
Acceptable sizes for automatic
Location
Maximum size
Paper weight
size detection
Other than North America: A3, A4,
A4-R, A5-R, B4, B5, B5-R
North America: LD, LG, LT, LT-R,
ST-R
Original glass
—
Length: 297 mm (11.69")
Width: 432 mm (17.01")
1-sided originals: 35 - 209 g/m2
(9.3 - 110 lb.) *1
2-sided originals: 50 - 157 g/m2
Other than North America: A3, A4,
A4-R, A5-R, B4, B5, B5-R, FOLIO
North America: LD, LG, LT, LT-R,
ST-R, COMP
RADF
(13.3 - 41.8 lb.)
*1 You may not obtain enough image quality when an original with a paper weight of more than 157 g/m2 (41.8 lb.) is used.
y Automatic size detection does not work properly when A/B format originals are used in equipment for North
America. It does not work properly when LT format originals are used in equipment other than that for North
America.
y Automatic size detection does not work properly when K format paper is used for printing. (K format is a standard
paper size in China.)
y Do not place any heavy objects (4 kg (9 lb.) or over) on the original glass and do not press on it with force.
y Be sure to place ST-size or A5-size originals in a landscape direction when using the RADF.
Maximum number of sheets for one scanning
A maximum of 2000 sheets can be scanned per 1 copy job or up until the embedded memory becomes full. When the
number of scanned sheets has exceeded the above limit, this equipment stops scanning and the message below appears.
If you want to print out the data scanned up until then, press [YES]. If you want to delete them, press [NO].
22 Placing Originals
Download from Www.Somanuals.com. All Manuals Search And Download.
2 HOW TO MAKE COPIES
2.HOW TO MAKE COPIES
„ Placing originals on the original glass
The original glass can be used for originals such as OHP films or tracing paper, as well as plain paper, that cannot be
placed on the RADF.
Do not place any heavy objects (4 kg (9 lb.) or over) on the original glass and do not press on it with force.
Breaking the glass could injure you.
Raise the RADF.
1
Raise it 60 degrees or more so that the size of the original can be detected correctly.
Place the original with its face down on the original
glass and align it against the left rear corner of the
glass.
2
When you copy highly transparent originals
When you copy highly transparent originals such as OHP films or
tracing paper, place a blank sheet, which is the same size as the
original or larger, over the original.
Lower the RADF carefully.
3
Placing Originals 23
Download from Www.Somanuals.com. All Manuals Search And Download.
2 HOW TO MAKE COPIES
„ Book-type originals
You can place book-type originals on the original glass.
Do not place any heavy objects (4 kg (9 lb.) or over) on the original glass and do not press on it with force.
Breaking the glass could injure you.
Raise the RADF.
1
Open the desired page of the original and place it with
its face down. Align it against the left rear corner of
the original glass.
2
When you make 2-sided copies from book-type originals in modes
such as book-type original to 2-sided copying or dual page copying,
align the center of the original on the yellow indicator line of the original
glass.
Lower the RADF carefully.
3
y Do not lower the RADF forcibly when the original is very thick. There will be no problem in copying even if it
is not fully lowered.
y Do not look directly at the original glass because intensive light may escape during copying.
24 Placing Originals
Download from Www.Somanuals.com. All Manuals Search And Download.
2 HOW TO MAKE COPIES
2.HOW TO MAKE COPIES
„ Using the RADF (Reversing Automatic Document Feeder)
‰ Precautions
Do not use the types of originals 1 to 8 shown below because such originals may cause misfeeding or damage to the
equipment.
1. Badly wrinkled, folded or curled originals
2. Originals with carbon paper
3. Taped, pasted or cut-out originals
4. Clipped or stapled originals
5. Originals with holes or tears
6. Damp originals
7. OHP films or tracing paper
8. Coated paper (with wax, etc.)
Use the types of originals 9 and 10 shown below with extra care.
9. Originals which resist sliding with the fingers, or surface-treated originals (The sheets of such originals may not be
separated.)
10. Folded or curled originals (They should be fully smoothed out before being used.)
1
2
3
4
7
5
6
10
8
9
When black streaks appear
If the scanning area or the guide area is dirty, image trouble such as black streaks may occur on printouts. Weekly
cleaning of these areas is recommended. For cleaning, refer to the Quick Start Guide.
Placing Originals 25
Download from Www.Somanuals.com. All Manuals Search And Download.
2 HOW TO MAKE COPIES
‰ Continuous feed mode
The feeding mode is set at “continuous feed mode” by default. Once you set the originals and then press the [START]
button, they are scanned page by page continuously. It is useful when you want to copy more than one original at one
time.
Align all the originals.
Collate the originals in the order that you want them to be copied. The top sheet of the originals will be copied first.
1
Place the originals with their face up and align the
side guides to the original length.
2
y Regardless of their sizes, originals are acceptable up to 100
sheets (35 to 80 g/m2 (9.3 to 20 lb.)) or 16 mm (0.62") in height.
y For mixed-size originals, see the following page:
For long originals
Pull out the original stopper so that the scanned original will not fall off.
After the original stopper was used, lift it slightly and push it in.
When there are too many originals to be scanned at one time, divide the originals into several sets before copying.
Place the first set of the originals and then press [CONTINUE] on the touch panel while the data of this set are being
scanned. When this scanning is finished, place the next set of the originals and press the [START] button on the
control panel.
26 Placing Originals
Download from Www.Somanuals.com. All Manuals Search And Download.
2 HOW TO MAKE COPIES
2.HOW TO MAKE COPIES
‰ Single feed mode
When the feeding mode is set at “single feed mode”, an original is fed automatically as it is placed on the RADF. It is useful
when you want to copy only 1 original sheet.
Align the side guides to the original length.
1
Insert the original with its face up and straight along
the side guides.
2
The original is automatically pulled in and then the menu of step 3 will
be displayed on the touch panel.
Be sure to let go of the original when it starts being pulled.
If there is another original, insert it in the same way.
3
The original is pulled in whether or not you press [YES].
After all the originals are pulled in, press [FINISHED].
4
Even if you do not press [FINISHED], copying will start when the current operation is cleared by means of the
automatic function clear.
Placing Originals 27
Download from Www.Somanuals.com. All Manuals Search And Download.
2 HOW TO MAKE COPIES
Making Copies
„ Basic copying procedure
Make copies following the procedure below.
2
RADF
Original glass
OR
1
4
3
5
Make sure that paper is placed in the drawer(s).
For the types and sizes of acceptable paper and how to place it, see the following pages:
1
2
Place the original(s).
For the types and sizes of originals and how to place them, see the following pages:
Key in the desired number of copies if you want more than one copy.
Press the [CLEAR] button on the control panel to delete the number keyed in.
3
4
Select the copy modes as required.
28 Making Copies
Download from Www.Somanuals.com. All Manuals Search And Download.
2 HOW TO MAKE COPIES
2.HOW TO MAKE COPIES
Press the [START] button on the control panel.
Copying starts. The paper exits with its copied side down.
5
Be careful because the paper exiting area and the paper itself are hot.
The menu shown below may appear when you are using particular modes.
This menu appears when “SADF (single feed mode)” is set to the document feeder or in modes where the original
is placed on the original glass and the scanned data are temporarily stored in the memory, such as sort copying or
1-sided to 2-sided copying. When this menu appears, follow the procedure below.
Place the next original on the original glass, and then press the [START] button on the
control panel.
6
7
Scanning starts.
Press [FINISHED] on the touch panel after all the originals have been scanned.
Copying starts.
When the drawer runs out of paper during copying, another drawer can feed paper instead if it holds paper of
the same size and orientation, and copying will not stop. If there is no such drawer, copying stops and “Add
paper” appears on the touch panel. In this case, add paper in the drawer.
Making Copies 29
Download from Www.Somanuals.com. All Manuals Search And Download.
2 HOW TO MAKE COPIES
‰ Stopping and restarting copying
Press the [STOP] button on the control panel.
Copying or scanning stops.
1
Press [MEMORY CLEAR] on the touch panel to stop copying. Press the [START] button
on the control panel to restart.
2
When you press [MEMORY CLEAR], the scanned data will be deleted and any waiting jobs will be performed.
Even if you do not press [MEMORY CLEAR], the scanned data will be deleted by means of the automatic
function clear.
30 Making Copies
Download from Www.Somanuals.com. All Manuals Search And Download.
2 HOW TO MAKE COPIES
2.HOW TO MAKE COPIES
„ Scanning the next original during copying
Even if copying is in progress or “READY (WARMING UP)” is displayed on the touch panel, you can scan the next original
(auto job start). Up to 10 jobs can be stored in the memory.
Place the original(s).
1
Set the number of copy sets and the copy modes as required.
2
The new job starts in the copy modes that you previously selected unless you select other modes.
Press the [START] button on the control panel.
3
y Up to 10 jobs can be stored in the memory. When the originals
for the 11th job are placed and the [START] button is pressed,
“Auto Start” appears on the touch panel. Scanning of the 11th
job starts when a waiting space for this job becomes available
as the preceding jobs are processed.
y A maximum of 2000 sheets (A4-size and LT-size originals) can
be scanned per 1 copy job or up until the embedded memory
becomes full.
Confirming auto jobs
You can confirm which jobs are in waiting on the touch panel or cancel them as required. For details, see the following
page:
Canceling jobs being scanned
Press the [STOP] button on the control panel to stop a job while originals are
being scanned.
When you press [MEMORY CLEAR] on the touch panel or the [FUNCTION
CLEAR] button on the control panel while the scanning is being paused, the
scanning will end. (In this case, the data which were scanned before the job
is paused will be copied.) To restart the scanning, press the [START] button.
To cancel the 11th auto job, press the [STOP] button.
Making Copies 31
Download from Www.Somanuals.com. All Manuals Search And Download.
2 HOW TO MAKE COPIES
„ Interrupting copying and making other copies
You can interrupt the copy job in progress to make other copies (interrupt copying). When restarting the interrupted job,
you do not have to reselect copy modes that have been set because they are memorized in this equipment.
y The following functions cannot be used together with interrupt copying:
Cover sheet copying, Sheet insertion copying, Job build, Store to e-Filing, Copy & File
y During interrupt copying, the mode cannot be changed by pressing the [e-FILING], [SCAN], [PRINT] or [FAX]
button on the control panel.
Press the [INTERRUPT] button on the control panel.
“Job interrupted job 1 saved” appears and then the [INTERRUPT]
button lights.
1
If the original is being scanned, the message above appears after
the scanning has finished.
Replace the original with a new one.
2
Select other copy modes as required and then press the [START] button on the control
panel.
3
Press the [INTERRUPT] button again after the interrupt copying has finished.
“READY to resume job 1” appears and the interrupted job restarts.
4
Even if you do not press the [INTERRUPT] button, an interrupted copy job will restart when the current status is
cleared by means of the automatic function clear after a specified period of time.
32 Making Copies
Download from Www.Somanuals.com. All Manuals Search And Download.
2 HOW TO MAKE COPIES
2.HOW TO MAKE COPIES
„ Proof copy
When you make a large amount of copies, you can check if they will be made exactly as you desire by copying only one
page before copying them all (proof copy). Then you can change the modes or settings (e.g. the number of copy sets,
receiving tray, page number, time stamp, sort/stapling, hole punching) after checking the proof copy.
If you want to change settings such as the reproduction ratio, density, original mode or 1/2-sided copying, you must
finish the proof copy first. Then change these settings and scan the original again.
Place paper in the drawer(s).
1
Place the original(s).
2
Select the number of copy sets and copy modes.
3
Press [PROOF COPY] on the touch panel.
“PROOF COPY is set Press START button to copy” appears for approx. 2 seconds.
4
If [NON-SORT NON-STAPLE] or [GROUP] is selected as a finishing mode, the mode will be changed to
[SORT] automatically.
Press the [START] button on the control panel.
Scanning starts. 1 set of copies will be printed out.
5
Making Copies 33
Download from Www.Somanuals.com. All Manuals Search And Download.
2 HOW TO MAKE COPIES
Change the number of copy sets and copy modes as required after checking the proof
copy.
6
Modes or settings such as the number of copy sets, the receiving tray, page number, time stamp, sort/stapling and
hole punching can be changed.
If you want to change settings such as the reproduction ratio, density, original mode or 1/2-sided copying, you
must finish the proof copy first. Then change these settings and scan the original again. Press [MEMORY
CLEAR] on the touch panel or the [FUNCTION CLEAR] button on the control panel to end the proof copy.
Press the [START] button on the control panel.
7
If you did not change the number of copies in step 6 above, the number of copies printed out will be one fewer than
that previously set because you have already copied one as a proof copy. (However, if the number of copies you
previously set was 1, another set of copies will be printed out besides the proof copy.)
34 Making Copies
Download from Www.Somanuals.com. All Manuals Search And Download.
2 HOW TO MAKE COPIES
2.HOW TO MAKE COPIES
„ Selecting exit tray
You can select the exit tray if an optional finisher is installed.
y The available exit tray may be restricted depending on copy modes and paper sizes.
y Exit tray selection is set at automatic selection by default.
Changing the exit tray
The exit tray currently selected is displayed on the equipment status indication area. To change the exit tray, press [EXIT
TRAY]. Every time you press this, the display changes from each tray of the finisher and automatic selection.
Exit tray auto-selection
indication
Current exit tray
[
]
EXIT TRAY button
Making Copies 35
Download from Www.Somanuals.com. All Manuals Search And Download.
2 HOW TO MAKE COPIES
Bypass Copying
When you make copies on OHP film, sticker labels or non-standard size paper, place the copy paper on the bypass tray.
Bypass copying is also recommended for copying on standard size paper which is not set in any of the drawers.
If you select the paper size, you can utilize various functions such as the automatic paper selection (APS) or the
automatic magnification selection (AMS). For details, see the following page:
Open the bypass tray for bypass copying.
If the paper is large, pull out the paper holder.
The operating procedure for bypass copying differs depending on the paper size to be used. See the table below for the
operating procedure of each size.
Paper size
Procedure
Other than North America:
A3, A4, B4, B5
North America: LD, LT, LG,
ST-R
Standard size
Other than the above
Others (Non-standard sizes)
y Bypass copying stops when the paper placed on the bypass tray runs out during copying, even if the paper of the
same size is in any of the drawers. Copying restarts when paper is supplied to the bypass tray.
y When bypass copying has been completed, the [FUNCTION CLEAR] button on the control panel blinks. Press this
button to switch bypass copying to normal copying using the drawers.
(Even if you do not press the [FUNCTION CLEAR] button, bypass copying will be switched to normal copying using
the drawers when the current status is cleared by means of the automatic function clear after a specified period of
time.)
36 Bypass Copying
Download from Www.Somanuals.com. All Manuals Search And Download.
2 HOW TO MAKE COPIES
2.HOW TO MAKE COPIES
„ Bypass copying on standard size paper
‰ Copying on A3, A4, B4 and B5 size paper (in equipment other than for North
America) / LD, LT, LG and ST-R size paper (in equipment for North America)
Place the original(s).
1
Place paper with its copy side up on the bypass tray.
Then align the side guides to the paper length while
holding the tab.
2
When paper is placed, the menu for bypass copying appears.
y The height of the paper must not exceed the indicator on the side guides.
y When you use more than one sheet of paper, fan the sheets well before placing them on the bypass tray. Be
careful not to cut your fingers when fanning them.
y Do not push paper into the entrance of the bypass feeder. This could cause a paper jam.
Press the button of the same size as that of the paper you placed on the bypass tray.
3
The paper size is now set.
If the paper size is not selected in this step, copying may be slowed down.
Bypass Copying 37
Download from Www.Somanuals.com. All Manuals Search And Download.
2 HOW TO MAKE COPIES
2.HOW TO MAKE COPIES
y If you select a wrong paper type, this could cause a paper jam or significant image trouble.
y When you select a paper type, you can confirm it with the icons displayed on the equipment status
indication area as shown below.
Paper type
PLAIN
Icon
Paper type
THICK 3
Icon
—
THICK 1
THICK 2
TRANSPARENCY
TAB PAPER
y Automatic 2-sided copying can be applied to plain paper, THICK 1, THICK 2 and THICK 3.
y For OHP films (TRANSPARENCY), only 1-sided copying can be performed.
y For tab paper, only 1-sided copying can be performed on its front side.
Select other copy modes as required, and then press the [START] button on the control
panel.
6
When you copy on sheets of OHP film, remove the copied OHP film one sheet at a time as they exit onto the
receiving tray. If the sheets of OHP film pile up, they may get curled and may not be projected properly.
Bypass Copying 39
Download from Www.Somanuals.com. All Manuals Search And Download.
2 HOW TO MAKE COPIES
‰ Copying on other than the above standard sizes of paper
Place the original(s) and paper in the same procedure noted in steps 1 and 2 in
Press [SIZE SETTING] on the touch panel.
2
Press the button of the same size as the paper you placed on the bypass tray.
3
Press [OTHER] under “COPY”.
4
The paper size is now set.
If the paper size is not selected in this step, copying may be slowed down.
40 Bypass Copying
Download from Www.Somanuals.com. All Manuals Search And Download.
2 HOW TO MAKE COPIES
2.HOW TO MAKE COPIES
Press [PAPER TYPE] if the paper you placed on the bypass tray is other than plain
paper.
5
Press the button of the same paper type as the paper you placed on the bypass tray.
Then press [OK].
6
y If you select a wrong paper type, this could cause a paper jam or significant image trouble.
y When you select a paper type, you can confirm it with the icons displayed on the equipment status
indication area. For details, see the following page:
Table in step 5 in “Copying on A3, A4, B4 and B5 size paper (in equipment other than for North America) /
Select other copy modes as required, and then press the [START] button on the control
panel.
7
Bypass Copying 41
Download from Www.Somanuals.com. All Manuals Search And Download.
2 HOW TO MAKE COPIES
„ Bypass copying on non-standard size paper
You can use non-standard size paper within the sizes shown on the right.
-
148 432 mm
5.8" 17"
(
-
)
-
100 297 mm
3.9" 11.7"
(
-
)
Place the original on the original glass.
1
Place paper with its copy side up on the bypass tray.
Then align the side guides to the paper length while
holding the tab.
2
When paper is placed, the menu for bypass copying appears.
y The height of the paper must not exceed the indicator on the side guides.
y When you use more than one sheet of paper, fan the sheets well before placing them on the bypass tray. Be
careful not to cut your fingers when fanning them.
y Do not push paper into the entrance of the bypass feeder. This could cause a paper jam.
Press [CUSTOM PAPER] on the touch panel.
3
42 Bypass Copying
Download from Www.Somanuals.com. All Manuals Search And Download.
2 HOW TO MAKE COPIES
2.HOW TO MAKE COPIES
Key in the dimension.
4
1) Press [LENGTH] and key in the value. (100 mm to 297 mm (3.94" to 11.69"))
2) Press [WIDTH] and key in the value. (148 mm to 432 mm (5.83" to 17.01"))
3) Press [OK].
Length and width are indicated as shown on the right:
Width
Length
To call up the dimension data registered previously, press the desired button from [MEMORY 1] to [MEMORY 4],
and then press [OK].
To register dimension data into the memory, see the following page:
Select other copy modes as required, and then press the [START] button on the control
panel.
5
Bypass Copying 43
Download from Www.Somanuals.com. All Manuals Search And Download.
2 HOW TO MAKE COPIES
‰ Registering non-standard size in the memory
Follow the same procedure noted in steps 1 to 3 in “Bypass copying on non-standard
1
Register dimensions.
2
1) Select a desired memory number.
2) Press [LENGTH] and key in the value. (100 mm to 297 mm (3.94" to 11.69"))
3) Press [WIDTH] and key in the value. (148 mm to 432 mm (5.83" to 17.01"))
4) Press [MEMORY].
44 Bypass Copying
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
BASIC COPY MODES
This chapter describes the basic copying functions including how to change the reproduction ratio, how to set sorting
modes or how to perform duplex copying.
Confirming the set functions.................................................................................................................................46
Clearing the set functions.....................................................................................................................................47
Restrictions on function combinations..................................................................................................................47
Copying mixed-size originals in one operation.....................................................................................................50
Selecting Finishing Mode...................................................................................................... 60
Sort/Group mode..................................................................................................................................................62
Rotate sort mode..................................................................................................................................................64
Duplex Copying...................................................................................................................... 72
Making a 2-sided copy from a book-type original.................................................................................................75
Performing Copy & File .........................................................................................................78
Download from Www.Somanuals.com. All Manuals Search And Download.
3 BASIC COPY MODES
Before Using Copying Functions
„ Default settings
This equipment is under its “default settings” when the power is turned ON, namely, if no setting change has been applied
yet, the equipment’s settings return to the default ones when the energy saving mode is cleared or the [FUNCTION
CLEAR] button on the control panel is pressed. The default settings for basic copy modes at installation are shown below.
Item
Default setting
Reproduction ratio
Copy quantity
100%
1
Paper selection
Simplex/Duplex
Density adjustment
Original mode
Automatic Paper Selection (APS)
1-sided original -> 1-sided copy
Automatic adjustment
TEXT/PHOTO
Finishing mode
When using the original glass:
NON-SORT NON-STAPLE
When using the RADF (Reversing Automatic Document Feeder):
SORT
Feeding mode when using the RADF
Continuous feed mode
The default settings are changeable. For details, refer to the MFP Management Guide.
„ Confirming the set functions
If you press [SETTINGS] on the touch panel, the menu shown below is displayed. On this menu, you can view the
functions that are currently set.
46 Before Using Copying Functions
Download from Www.Somanuals.com. All Manuals Search And Download.
3 BASIC COPY MODES
3.BASIC COPY MODES
„ Clearing the set functions
If you want to clear any settings of the EDIT menu, press the button of the desired functions.
If you want to clear any setting of the IMAGE menu, reset the adjustment value in the setting menu of the desired
functions.
Clearing all settings changed
When you press the [FUNCTION CLEAR] button on the control panel, all the function changes will be cleared.
Even if you do not press the [FUNCTION CLEAR] button, the changes will be cleared if the equipment is left idle for 45
sec. (default setting). For how to change this period, refer to the MFP Management Guide.
„ Restrictions on function combinations
Several copy functions can be used together. However some functions may not be used with other ones. For details, see
the following page:
Before Using Copying Functions 47
Download from Www.Somanuals.com. All Manuals Search And Download.
3 BASIC COPY MODES
Paper Selection
„ Automatic Paper Selection (APS)
This equipment detects the size of an original and selects paper of the same size automatically. This function is called
Automatic Paper Selection (APS).
y For the original sizes detectable, see the following page:
y Some original sizes may not be detected with this function. In this case, select the desired size manually.
Place paper in the drawer(s).
1
Place the original(s).
2
Press [APS] on the touch panel.
3
The paper selection mode is now set at Automatic Paper Selection.
y The paper selection mode is set at Automatic Paper Selection by default.
y Even if the direction of the paper placed in the selected drawer differs from that of the original, this
equipment rotates the data of the original by 90 degrees to make copies as long as their sizes are the same.
(This works on A4, B5 or LT paper only.) For example, when an A4 original is placed in a portrait direction
and A4-R paper is placed in the drawer, the data of the A4 original will be rotated and copied correctly on
A4-R paper.
If “Change direction of original” or “CHANGE DRAWER TO CORRECT PAPER SIZE” appears, follow the
directions.
Select other copy modes as required, and then press the [START] button on the control
panel.
4
48 Paper Selection
Download from Www.Somanuals.com. All Manuals Search And Download.
3 BASIC COPY MODES
3.BASIC COPY MODES
„ Selecting desired paper manually
You need to select paper by yourself when copying the following originals whose sizes cannot be detected correctly:
y Highly transparent originals (e.g. OHP film, tracing paper)
y Totally dark originals or originals with dark borders
y Non-standard size originals (e.g. newspaper, magazines)
When paper of the size you want to use is not in any drawer, place it in a drawer or on the bypass tray.
Place paper in the drawer(s).
When using bypass copying, be sure to set the paper size.
1
Place the original(s).
2
Press the drawer button corresponding to the desired paper size.
3
Select other copy modes as required, and then press the [START] button on the control
panel.
4
Paper Selection 49
Download from Www.Somanuals.com. All Manuals Search And Download.
3 BASIC COPY MODES
„ Copying mixed-size originals in one operation
You can copy a set of originals whose sizes are individually different, using the RADF (Reversing Automatic Document
Feeder).
The original sizes that can be mixed are as follows:
North America: LD, LG, LT, LT-R, COMP
Other than North America: A3, A4, A4-R, B4, B5, FOLIO
Place paper in the drawer(s).
The bypass tray cannot be used. Use drawers.
1
Adjust the side guides to the widest original, and then align the originals against the
side guide on the front side.
2
When original widths are the same
When original widths are not the same
When copying originals of different widths, the copied image of the smaller one may be skewed because it does
not touch the side guide on the rear side.
Press [ZOOM] on the touch panel.
3
50 Paper Selection
Download from Www.Somanuals.com. All Manuals Search And Download.
3 BASIC COPY MODES
3.BASIC COPY MODES
Press [MIXED SIZE].
4
Press [AMS] to make copies on paper in one size. To make copies on paper of the same
size as the originals, press [CLOSE] so that the menu returns to the BASIC menu, and
then press [APS].
5
When [AMS] is selected:
y In the Automatic Magnification Selection, copy images cannot be enlarged from A4 (portrait), B5 (portrait) or
LT (portrait) to A3 (landscape), B4 (landscape), LD (landscape) or LG (landscape). In this case, place A4,
B5 or LT originals in a landscape direction.
y Before you use Automatic Paper Selection, be sure that all paper sizes corresponding to the original sizes
have been placed in the drawers.
Select other copy modes as required, and then press the [START] button on the control
panel.
6
If “Change direction of original” appears while scanning is in progress, remove the original from the RADF and
change its direction accordingly.
Paper Selection 51
Download from Www.Somanuals.com. All Manuals Search And Download.
3 BASIC COPY MODES
Setting Original Modes
You can make copies with the optimal image quality by selecting the following modes for your original.
TEXT/PHOTO: Originals with text and photographs mixed
TEXT: Originals with text (or text and line art) only
PHOTO: Originals with photographs
TEXT/PHOTO is set by default.
Press [ORIGINAL MODE] on the touch panel.
1
Select the original mode.
2
52 Setting Original Modes
Download from Www.Somanuals.com. All Manuals Search And Download.
3 BASIC COPY MODES
Density Adjustment
This equipment detects the density level of originals and automatically adjusts the density level of the copied image to the
optimal one. Alternatively, you can manually adjust it to the desired level.
Adjusting automatically (automatic density adjustment)
Press [AUTO] on the touch panel.
The automatic density adjustment is set by default at installation.
Adjusting manually
Press either
or
to select the desired density level.
Density Adjustment 53
Download from Www.Somanuals.com. All Manuals Search And Download.
3 BASIC COPY MODES
Enlargement and Reduction Copying
You can change the reproduction ratio of copied images in the following procedures:
Automatic Magnification Selection (AMS):
You need to specify the copy paper size in advance. Then this equipment will detect the original size and automatically
select the optimal reproduction ratio for the copy paper size.
Specifying both original size and copy paper size separately:
You need to specify both the original size and the copy paper size separately in advance. According to the sizes you
specified, the optimal reproduction ratio is selected automatically. It is used when the Automatic Magnification Selection is
not available, such as when copying OHP film originals.
Specifying reproduction ratio manually:
You can select the desired reproduction ratio by pressing [ZOOM] or one-touch zoom buttons on the touch panel.
The available range of reproduction ratio differs depending on whether the original is placed on the original glass or on
the RADF (Reversing Automatic Document Feeder).
Original glass: 25 to 400%
RADF: 25 to 200%
„ Automatic Magnification Selection (AMS)
Specify the copy paper size in advance so that this equipment will detect the original size and automatically select the
optimal reproduction ratio to the copy paper size.
This function is available when the size of the originals is as follows:
North America: LD, LG, LT, LT-R, ST-R and COMP (COMP is available only when the RADF is used.)
Other than North America: A3, A4, A4-R, A5-R, B4, B5, B5-R, FOLIO (FOLIO is available only when the RADF is used.)
This function does not work properly for the originals noted below. Select other methods when copying them.
y Highly transparent originals (e.g. OHP film, tracing paper)
y Totally dark originals or ones with dark borders
y Non-standard size originals (e.g. newspapers, magazines)
Place paper in the drawer(s).
1
Press [ZOOM] on the touch panel.
2
54 Enlargement and Reduction Copying
Download from Www.Somanuals.com. All Manuals Search And Download.
3 BASIC COPY MODES
3.BASIC COPY MODES
Select the desired paper size and then press [AMS].
3
y If you want to select a paper size other than the following, you need to register the size as “OTHER”. Once
you register this size, it will be specified every time you press [OTHER] on the touch panel.
North America: LD, LG, LT, ST
Other than North America: A3, A4, B4, B5
For how to register, see the following page:
y Paper sizes can also be registered by pressing the desired drawer button of the equipment status indication
area on the BASIC menu.
Place the original(s).
4
5
If the original is placed on the original glass, the reproduction ratio is set when the original is placed. If the original
is placed on the RADF, the reproduction ratio is set when the original is scanned.
If “Change direction of original” appears, change it accordingly.
Select other copy modes as required, and then press the [START] button on the control
panel.
Enlargement and Reduction Copying 55
Download from Www.Somanuals.com. All Manuals Search And Download.
3 BASIC COPY MODES
„ Specifying both the original size and the copy paper size separately
Place paper in the drawer(s).
1
Place the original(s).
2
Press [ZOOM] on the touch panel.
3
Select the desired sizes for the original and copy paper.
4
y If you want to select a size other than the following for the original size and copy paper size, you need to
register the size as “OTHER”. Once you register this size, it will be specified every time you press [OTHER]
on the touch panel.
North America: LD, LG, LT, ST
Other than North America: A3, A4, B4, B5
For how to register, see the following page:
y Paper sizes can also be registered by pressing the desired drawer button of the equipment status indication
area on the BASIC menu.
Select other copy modes as required, and then press the [START] button on the control
panel.
5
56 Enlargement and Reduction Copying
Download from Www.Somanuals.com. All Manuals Search And Download.
3 BASIC COPY MODES
3.BASIC COPY MODES
‰ Registering paper sizes to “OTHER” size
If you want to select a size other than the following for the original size and copy paper size, you need to register the size
as “OTHER” following the procedures below. Once you register this size, it will be specified every time you press [OTHER]
on the touch panel.
North America: LD, LG, LT, ST
Other than North America: A3, A4, B4, B5
You can register only standard sizes as [OTHER] and cannot register any non-standard sizes.
Press [SIZE SETTING] on the touch panel.
1
Select the desired size.
2
The selected size will be registered as an “OTHER” size.
Enlargement and Reduction Copying 57
Download from Www.Somanuals.com. All Manuals Search And Download.
3 BASIC COPY MODES
„ Specifying reproduction ratio manually
Place paper in the drawer(s).
1
Place the original(s).
2
Press [ZOOM] on the touch panel.
3
Press the buttons below to select the desired reproduction ratio.
4
[
UP] and [ DOWN] buttons
The reproduction ratio changes by 1% every time either of them is pressed. When you hold either down, the
ratio goes up or down automatically.
One-touch zoom buttons
Select the desired ratio from [400%], [200%], [100%], [50%] and [25%].
When the RADF is used, the maximum ratio available is 200%.
58 Enlargement and Reduction Copying
Download from Www.Somanuals.com. All Manuals Search And Download.
3 BASIC COPY MODES
3.BASIC COPY MODES
Select the desired size.
5
y If you want to select a paper size other than the following, you need to register the size as “OTHER”. Once
you register this size, it will be specified every time you press [OTHER] on the touch panel.
North America: LD, LG, LT, ST
Other than North America: A3, A4, B4, B5
For how to register, see the following page:
y Paper sizes can also be registered by pressing the desired drawer button of the equipment status indication
area on the BASIC menu.
Select other copy modes as required, and then press the [START] button on the control
panel.
6
Enlargement and Reduction Copying 59
Download from Www.Somanuals.com. All Manuals Search And Download.
3 BASIC COPY MODES
Selecting Finishing Mode
„ Finishing modes and optional finishing devices
See the table below for each finishing mode.
Finishing mode
Description
Copies exit without being sorted or stapled.
Non-sort Non-staple
Sort (
Copies exit in the same page order as the originals one set after another.
Copies grouped by page exit.
Group (
Rotate sort (
Staple sort (
Copies exit set by set alternately in a different direction.
Copies exit with their corner stapled.
Magazine sort (
Saddle stitch (
Copies exit in a book-type page order.
Copies exit in a book-type page order with their center folded and stapled.
Magazine sort and saddle stitch are used together.
Magazine sort & saddle stitch
(
Hole punch (
Copies exit with their side punched.
Inserter mode (
Stapling and hole punching the sheets without making copies
The available finishing modes differ depending on the type of optional finishing devices (Finisher, Hole Punch Unit and
Inserter) installed. Finishing devices available for this equipment are as follows:
Finisher
y Finisher MJ-1027
y Saddle Stitch Finisher MJ-1028/MJ-1029
Hole Punch Unit
Hole Punch Unit MJ-6003
Inserter
Inserter MJ-7001
Check the finishing modes enabled with each finishing device.
Finishing mode
Magazine
Devices
Sort/
Group
Rotate
sort
Staple
sort
Magazine
sort
sort &
saddle
stitch
Saddle
stitch
Hole
punch
Inserter
mode
MJ-1027 &
MJ-6003 &
MJ-7001
Yes
Yes
—
—
Yes
Yes
Yes
Yes
—
—
—
—
Yes
Yes
Yes
—
MJ-1027&
MJ-6003
MJ-1027&
MJ-7001
Yes
Yes
—
—
Yes
Yes
Yes
Yes
—
—
—
—
—
—
Yes
—
MJ-1027
MJ-1028/1029 &
MJ-6003 &
Yes
—
Yes
Yes
Yes
Yes
Yes
Yes
MJ-7001
MJ-1028/1029 &
MJ-6003
Yes
Yes
—
—
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
—
—
MJ-1028/1029 &
MJ-7001
Yes
MJ-1028/1029
No device
Yes
Yes
—
Yes
—
Yes
Yes
Yes
—
Yes
—
—
—
—
—
Yes
60 Selecting Finishing Mode
Download from Www.Somanuals.com. All Manuals Search And Download.
3 BASIC COPY MODES
3.BASIC COPY MODES
‰ Name of each part of the finishers (optional)
MJ-1027
7
1. Tray 1
2. Sub-tray
3. Tray 2
4. Front cover
5. Hole Punch Unit MJ-6003
6. Inserter MJ-7001
7. Upper cover
6
5
4
1
2
3
2
MJ-1028/1029
1
9
1. Tray 1
2. Sub-tray
3. Tray 2
4. Saddle stitch tray
5. Lower cover
6. Front cover
7. Hole Punch Unit MJ-6003
8. Inserter MJ-7001
9. Upper cover
8
7
6
2
3
2
5
4
Selecting Finishing Mode 61
Download from Www.Somanuals.com. All Manuals Search And Download.
3 BASIC COPY MODES
„ Sort/Group mode
When you make more than one set of copies, they can be made to exit in the same page order as that of the originals.
This mode is called the sort mode. Copies can also be made to exit grouped by page. This mode is called the group mode.
Sort mode
1
1
1
2
2
2
3
3
3
Group mode
1
1
1
2
2
2
3
3
3
When you use large-size paper, such as A3, B4, LD and LG, pull out the sub-tray in advance so that the copied paper
will not fall off and will be sorted neatly.
Place paper in the drawer(s).
1
Place the original(s).
2
When you place originals on the RADF (Reversing Automatic Document Feeder), the display of the sorting
mode button will change to “SORT”.
Press [FINISHING] on the touch panel.
3
62 Selecting Finishing Mode
Download from Www.Somanuals.com. All Manuals Search And Download.
3 BASIC COPY MODES
3.BASIC COPY MODES
Press [SORT] or [GROUP].
4
Select other copy modes as required, and then press the [START] button on the control
panel.
5
Selecting Finishing Mode 63
Download from Www.Somanuals.com. All Manuals Search And Download.
3 BASIC COPY MODES
„ Rotate sort mode
When you make more than one set of copies, one set can be made to exit on top of another set, alternating in portrait and
landscape directions. This mode is called the rotate sort mode. Use 2 drawers and 2 stacks of paper of the same size.
Place one stack of paper in one drawer in a portrait direction and place the other in another drawer in a landscape
direction before you start copying.
y A4, B5 and LT sized paper placed on the drawer or bypass tray can be used.
y The rotate sort mode is not available when Automatic Paper Selection is selected.
y When an optional finisher is installed, this mode cannot be used.
Place paper in the drawer(s).
1
Place the original(s).
2
Press [FINISHING] on the touch panel.
3
Press [ROTATE SORT].
4
Select other copy modes as required, and then press the [START] button on the control
panel.
5
64 Selecting Finishing Mode
Download from Www.Somanuals.com. All Manuals Search And Download.
3 BASIC COPY MODES
3.BASIC COPY MODES
„ Staple sort mode
When you make more than one set of copies, the copied paper can be automatically stapled set by set. This mode is
called the staple sort mode. You can choose from 3 different stapling positions.
Example: When [FRONT STAPLE] is selected
y Special paper such as OHP film or sticker labels is not applicable.
y Copies in different sizes cannot be stapled. (If the lengths of the copies are the same, they can be stapled.)
Place paper in the drawer(s).
When using bypass copying, be sure to set the paper size.
1
Place the original(s).
2
Press [FINISHING] on the touch panel.
3
Select the desired stapling position from [FRONT STAPLE], [DOUBLE STAPLE] or
[REAR STAPLE].
4
Selecting Finishing Mode 65
Download from Www.Somanuals.com. All Manuals Search And Download.
3 BASIC COPY MODES
Select other copy modes as required, and then press the [START] button on the control
panel.
5
When the number of sheets exceeds the maximum number of sheets available for stapling, this equipment
automatically enters into the sort mode.
‰ Maximum number of sheets available for stapling
The maximum number of sheets available for stapling differs depending on the type of the finishing device installed, paper
size or paper weight.
Finisher MJ-1027 / Saddle Stitch Finisher MJ-1028
Paper weight
Paper size
64 - 80 g/m2
81 - 90 g/m2
91 - 105 g/m2
(17 - 20 lb. Bond)
(21 - 24 lb. Bond)
(25 - 28 lb. Bond)
A4, B5, LT
50 sheets
30 sheets
30 sheets
15 sheets
30 sheets
15 sheets
A3, A4-R, B4, FOLIO, LD,
LG, LT-R, COMP
Saddle Stitch Finisher MJ-1029 (When staples for 100-sheet stapling are used)
Paper weight
Paper size
64 - 80 g/m2
81 - 90 g/m2
91 - 105 g/m2
(17 - 20 lb. Bond)
(21 - 24 lb. Bond)
(25 - 28 lb. Bond)
A4, B5, LT
100 sheets
50 sheets
—
—
—
—
A3, A4-R, B4, FOLIO, LD,
LG, LT-R, COMP
Saddle Stitch Finisher MJ-1029 (When staples for 50-sheet stapling are used)
Paper weight
Paper size
64 - 80 g/m2
81 - 90 g/m2
91 - 105 g/m2
(17 - 20 lb. Bond)
(21 - 24 lb. Bond)
(25 - 28 lb. Bond)
A4, B5, LT
50 sheets
30 sheets
30 sheets
15 sheets
30 sheets
15 sheets
A3, A4-R, B4, FOLIO, LD,
LG, LT-R, COMP
y 2 cover sheets can be added to paper whose weight is 64 to 256 g/m2 (17 lb. Bond to 140 lb. Index). In this case,
the number of sheets available shall include the 2 cover sheets.
y For the maximum number of sheets loadable on the tray, refer to the Quick Start Guide.
66 Selecting Finishing Mode
Download from Www.Somanuals.com. All Manuals Search And Download.
3 BASIC COPY MODES
3.BASIC COPY MODES
„ Magazine sort / Saddle stitch
You can copy more than one original and bind them in a booklet format. This mode is called the magazine sort mode. Also
you can have the copied booklet folded and stapled at its center. This mode is called the saddle stitch mode.
Magazine sort mode
1
6
7
2
4
9
3
2
11
12
Magazine sort & saddle stitch mode
1
2
6
7
3
12
Saddle stitch mode
12
10
1
6
7
3
8
5
Requirements for saddle stitching
Maximum number of sheets
available for saddle stitching *2
Maximum number of sets loadable
on the saddle stitch tray *3
Paper weight *1
Paper size
11 - 15 sheets / 10 sets
6 - 10 sheets / 20 sets
Less than 5 sheets / 25 sets
64 - 80 g/m2
(17 - 20 lb. Bond)
15 sheets
10 sheets
A3, A4-R, B4, LD,
LT-R, LG
81 - 105 g/m2
(21 - 28 lb. Bond)
6 - 10 sheets / 15 sets
Less than 5 sheets / 25 sets
*1 When the paper weights are mixed, take the value of the heavier one.
*2 1 cover sheet (64 to 256 g/m2 (17 lb. Bond to 140 lb. Index)) can be added. In this case the number of sheets per set shall include the
cover sheet.
*3 When 1 cover sheet of 200 to 256 g/m2 (110 to 140 lb. Index) is added to paper of 81 to 105 g/m2 (21 to 28 lb. Bond), a maximum of 5 sets
can be loaded on the saddle stitch tray.
When placing portrait originals in a landscape direction as shown on the
right in the magazine sort mode or the magazine sort & saddle stitch
mode, set the image direction function to ON on the EDIT menu.
Otherwise the originals will not be copied in the proper page order.
The magazine sort mode can also be selected on the EDIT menu. If you select it on the EDIT menu, you can adjust the
binding margin. For details, see the following page:
Selecting Finishing Mode 67
Download from Www.Somanuals.com. All Manuals Search And Download.
3 BASIC COPY MODES
Place paper in the drawer(s).
1
Special paper such as OHP film or sticker labels is not applicable.
Select the desired paper size.
Sizes are available as follows:
2
3
Magazine sort: A3, A4-R, A5-R, B4, B5-R, LD, LT-R, LG, ST-R
Magazine sort & saddle stitch, Saddle stitch: A3, A4-R, B4, LD, LT-R, LG
Place the original(s).
When placing the originals on the RADF, place them according to the illustration on the previous page.
When placing the originals on the original glass, place them in the following order:
Magazine sort, Magazine sort & saddle stitch: Place the first page of the original first.
Saddle stitch: For example, if the total number of pages is 12, place pages 1 and 12 together, and then pages
2 and 11, then pages 10 and 3, then pages 4 and 9, then pages 8 and 5, then pages 6 and 7.
Press [FINISHING] on the touch panel.
4
Select the desired mode from [MAGAZINE SORT], [MAGAZINE SORT & SADDLE
STITCH] and [SADDLE STITCH].
5
[MAGAZINE SORT & SADDLE STITCH] and [SADDLE STITCH] are selectable only when the Saddle Stitch
Finisher (optional) is installed.
Select other copy modes as required, and then press the [START] button on the control
panel.
6
68 Selecting Finishing Mode
Download from Www.Somanuals.com. All Manuals Search And Download.
3 BASIC COPY MODES
3.BASIC COPY MODES
„ Hole punch mode
You can punch copied paper when the Hole Punch Unit (optional) is installed on a finisher.
y Paper whose size is any of A3, A4, A4-R, B4, B5, B5-R, FOLIO, LD, LG, LT, LT-R, ST-R and COMP, and whose
weight is 64 to 256 g/m2 (17 lb. Bond to 140 lb. Index) is available.
y Special paper such as OHP film or sticker labels is not applicable.
Place paper in the drawer(s).
When using bypass copying, be sure to set the paper size.
1
Place the original(s).
2
3
Press [FINISHING] on the touch panel.
Press [HOLE PUNCH].
4
5
Select other copy modes as required, and then press the [START] button on the control
panel.
Selecting Finishing Mode 69
Download from Www.Somanuals.com. All Manuals Search And Download.
3 BASIC COPY MODES
„ Inserter mode
You can add a cover sheet previously created or insert a color page at a specified position using the Inserter (optional).
Also, you can set paper on the Inserter to only have sheets stapled, hole-punched and stitched without making copies.
This section explains how to set paper on the Inserter, how to only staple, hole-punch and stitch sheets without performing
copying. See the following page for how to insert a cover sheet and a color page at a specified position.
‰ Placing paper on the Inserter
The following paper can be set on the Inserter.
Paper size
A3, A4, A4-R, B4, B5, FOLIO, LD, LG, LT, LT-R, COMP
Media type *1
Plain paper: 64 - 80 g/m2 (17 - 20 lb. Bond)
Thick paper: 81 - 256 g/m2 (21 lb. Bond - 140 lb. Index)
Recycled paper
Special paper (e.g. OHP film, color paper) *2
64 - 80 g/m2 (17 - 20 lb. Bond): 100 sheets
81 - 256 g/m2 (21 lb. Bond - 140 lb. Index): Less than 12 mm (0.47") in paper height (less than 7
Maximum number of sheets
can be set
mm (0.28") in case of special paper)
*1 Note that some types of paper may not be applicable for the Inserter due to their paper qualities, even if you are using the paper listed above.
*2 Contact a Toshiba-product distributor for details of the special paper available.
There are some restrictions for stapling or saddle stitching the paper set on the Inserter. See the following pages for
details.
y Stapling:
y Saddle Stitching:
Place paper on the Inserter tray with its face up. Align
the side guides with the paper width.
The start lamp of the Inserter lights.
1
y Be sure that the height of the paper placed on the Inserter does
not exceed the line indicated on the side guide.
y Sheets of different sizes cannot be set together.
y Match the size and direction of the paper to be set on the
Inserter with those of the original or paper in the paper source.
If the paper size is large, extend the tray.
70 Selecting Finishing Mode
Download from Www.Somanuals.com. All Manuals Search And Download.
3 BASIC COPY MODES
3.BASIC COPY MODES
‰ Stapling and hole punching the sheets without making copies
You can place paper on the Inserter and only staple, hole punch or stitch the sheets without making copies. This is useful
when you forget to perform the finishing process after making copies.
Place paper on the Inserter.
1
When performing saddle stitching, place paper so that the cover or
back cover sheet will be at the bottom.
Perform settings of stapling and hole punching.
For stapling or saddle stitching, press the stapling button. The lamp corresponding to the selected staple mode
lights. Press the stapling button to switch the staple mode.
2
For hole punching, press the hole punch button. The hole punch lamp lights.
Hole punch
button/lamp
Staple
button/lamp
y Saddle stitching is available only when the Saddle Stitch Finisher (optional) is installed.
y The hole punch mode can be used together with the staple mode, not with the saddle stitch mode.
Press the start button on the Inserter.
The operation starts. The start lamp blinks during operation and all the
lamps go off when it has finished.
3
Selecting Finishing Mode 71
Download from Www.Somanuals.com. All Manuals Search And Download.
3 BASIC COPY MODES
Duplex Copying
You can copy a 1-sided original to a 2-sided copy or vice versa, or copy a 2-sided original to a 2-sided copy. This is useful
when you want to save the paper, or when you want to copy a book-type original maintaining the same page order.
-13-
3-
-13-
-12-
-15-
-12-
-15-
Use plain paper, THICK 1, THICK 2 or THICK 3 for duplex copying.
72 Duplex Copying
Download from Www.Somanuals.com. All Manuals Search And Download.
3 BASIC COPY MODES
3.BASIC COPY MODES
„ Making a 1-sided copy
When you copy 2-sided portrait originals which open to the left/right on only 1 side of the paper, use the image
direction function on the EDIT menu so that all the copied paper will exit in the proper direction.
“IMAGE DIRECTION” set
No setting
Place paper in the drawer(s).
When using bypass copying, be sure to set the paper size.
1
Place the original(s).
2
3
Press [2-SIDED] on the touch panel.
Select the desired mode.
4
[1->1 SIMPLEX]: 1-sided original to 1-sided copy
[2->1 SPLIT]: 2-sided original to 1-sided copy
Select other copy modes as required, and then press the [START] button on the control
panel.
5
Duplex Copying 73
Download from Www.Somanuals.com. All Manuals Search And Download.
3 BASIC COPY MODES
„ Making a 2-sided copy
If 1-sided portrait originals have been placed in a landscape direction and you copy them on both sides of the paper,
copied sheets are usually in the open to top/bottom direction. You can make copies in the open to left/right direction
with the image direction function.
“IMAGE DIRECTION” set
No setting
Place paper in the drawer(s).
When using bypass copying, be sure to set the paper size.
1
Place the original(s).
2
3
Press [2-SIDED] on the touch panel.
Select the desired mode.
4
[1 -> 2 DUPLEX]: 1-sided original to 2-sided copy
[2 -> 2 DUPLEX]: 2-sided original to 2- sided copy
Select other copy modes as required, and then press the [START] button on the control
panel.
5
When placing the original on the original glass, follow steps 6 and 7 on
74 Duplex Copying
Download from Www.Somanuals.com. All Manuals Search And Download.
3 BASIC COPY MODES
3.BASIC COPY MODES
„ Making a 2-sided copy from a book-type original
You can make 2-sided copies from book-type originals such as books or catalog as in the same page order.
A4, B5 and LT sizes are applicable.
Place paper in the drawer(s).
When using bypass copying, be sure to set the paper size.
1
Press [2-SIDED] on the touch panel.
2
Press [BOOK -> 2] on the touch panel.
3
Duplex Copying 75
Download from Www.Somanuals.com. All Manuals Search And Download.
3 BASIC COPY MODES
Select the book copying type.
4
Example: If pages 2 to 6 of a book which opens to the left are to be copied, select [LEFT -> LEFT].
2
3
6
7
Press the drawer button corresponding to the desired paper size.
Only A4, B5 and LT sizes are applicable.
5
Select other copy modes as required.
If the copy needs a binding space, select the book margin mode on the EDIT menu.
6
7
Place the original on the original glass.
Place the original with its bottom toward you, matching its center to the
yellow indicator under the original glass.
76 Duplex Copying
Download from Www.Somanuals.com. All Manuals Search And Download.
3 BASIC COPY MODES
3.BASIC COPY MODES
Do not place any heavy objects (4 kg (9 lb.) or over) on the original glass and do not press on it with
force.
Breaking the glass could injure you.
Press the [START] button on the control panel. Once the pages are scanned, set the
next ones on the original glass.
Repeat this step until all the desired pages have been scanned. If the last page is a single page, press [COPY
FINAL PAGE] on the touch panel, and then press the [START] button on the control panel to start scanning. The
scanned pages will be copied.
8
When all the pages have been scanned, press [FINISHED].
The scanned pages will be copied.
9
Even if you do not press [FINISHED], copying will start by means of the automatic function clear.
Duplex Copying 77
Download from Www.Somanuals.com. All Manuals Search And Download.
3 BASIC COPY MODES
Performing Copy & File
With the Copy & File function, you can store the copied data in the share folder of the hard disk of this equipment or a
specified PC on a network. The data can be stored in any of PDF, TIFF and XPS formats.
y The “COPY & FILE” function is available only when the Scanner Kit or Printer/Scanner Kit (both optional) is
installed.
y Scanned data are stored at the resolution of 600 dpi only. The data stored with this function are suited for printing
but not for being imported as an image into your PC. To obtain the optimal image quality for importing, it is
recommended to store the data with the Scan to File function of this equipment.
y The network administrator must make settings for Copy & File in advance. For details, refer to the TopAccess
Guide.
y It is recommended to back up the data stored in the share folder.
You can store data in an e-Filing box with the Store to e-Filing function. For details, refer to the e-Filing Guide.
Place the original(s).
1
Press [STORAGE] on the touch panel.
2
Press [COPY & FILE] on the touch panel.
3
78 Performing Copy & File
Download from Www.Somanuals.com. All Manuals Search And Download.
3 BASIC COPY MODES
3.BASIC COPY MODES
Press the necessary buttons for entering information about the data to be stored. Then
press [OK].
4
FILE NAME: Press this to display the on-screen keyboard. Then enter the file name within 45 letters.
MFP LOCAL: Press this to store the data into the share folder of this equipment.
REMOTE 1, REMOTE 2: Press either of them to store the data into the share folder of a PC that is connected with
this equipment via a network.
y You can select up to 2 of [MFP LOCAL], [REMOTE 1] and [REMOTE 2]. You can cancel the selected item
by pressing the same button again.
y When a user who has the privilege of changing the setting of [REMOTE 1] and [REMOTE 2] has pressed
either of them, the menu for specifying a directory appears. In this case, see the following page to specify
the directory:
PDF / TIFF / XPS: These are file formats in which the data are stored. Select one of them.
MULTI / SINGLE: These are for selecting whether the data are stored as a multiple page file or a single page file. If
you select “MULTI”, all the scanned data will be stored as one file. If you select “SINGLE”, a folder is created
and each page of the scanned data will be stored individually as one file in the folder.
Press the [START] button on the control panel.
When the original is placed on the RADF (Reversing Automatic Document Feeder), copying and storing start
simultaneously.
5
When the original is placed on the original glass, follow the procedure below.
Place the next original on the original glass, and then press the [START] button on the
control panel.
6
7
Repeat this step until the scanning of all the originals is finished.
When all have been scanned, press [FINISHED] on the touch panel.
Copying and storing start.
Performing Copy & File 79
Download from Www.Somanuals.com. All Manuals Search And Download.
3 BASIC COPY MODES
„ Setting share folder
When a user who has the privilege of setting a share folder has pressed [REMOTE 1] or [REMOTE 2], the menu for
specifying a directory appears.
The setting items differ depending on the file transfer protocol to be used. FTP, SMB, NetWare IPX/SPX and NetWare
TCP/IP are selectable for a file transfer protocol.
FTP
When you press any of the buttons below, the on-screen keyboard appears. Enter with the buttons on the touch panel or
the digital keys on the control panel. When you finish the entry, press [OK].
SERVER NAME: Press this to enter the IP address of FTP server. For example, if the data should be transferred to an
FTP folder ftp://10.10.70.101/user01/scan/, key in “10.10.70.101”.
NETWORK PATH: Press this to enter a network path to an FTP folder where the data are to be stored. For example, if the
data should be transferred to an FTP folder ftp://10.10.70.101/user01/scan/, enter “user01\scan”.
LOGIN USER NAME: Press this to enter a user name to login to the FTP server. Enter this as required.
PASSWORD: Press this to enter a password to login to the FTP server. Enter this as required.
COMMAND PORT: Press this to key in a command port number for executing commands. Normally “-” is entered in this
field and it means a port number set by the administrator will be used. Change this only when you want to use any
other port number.
SMB
When you press any of the buttons below, the on-screen keyboard appears. Enter with the buttons on the touch panel or
the digital keys on the control panel. When you finish the entry, press [OK].
NETWORK PATH: Press this to enter a network path to the folder where the data are to be stored.
LOGIN USER NAME: Press this to enter a user name to access the network folder. Enter this as required.
PASSWORD: Press this to enter a password to access the network folder. Enter this as required.
If you selected [SMB], the settings for [SERVER NAME] and [COMMAND PORT] are not required.
80 Performing Copy & File
Download from Www.Somanuals.com. All Manuals Search And Download.
3 BASIC COPY MODES
3.BASIC COPY MODES
NetWare IPX/SPX / NetWare TCP/IP
When you press any of the buttons below, the on-screen keyboard appears. Enter with the buttons on the touch panel or
the digital keys on the control panel. When you finish the entry, press [OK].
SERVER NAME: When you selected [NetWare IPX], enter either the server name of NetWare server or Tree/Context (if
NDS is useable). When you selected [NetWare IP], enter the IP address of NetWare server.
NETWORK PATH: Press this to enter a network path to a NetWare server folder where the data are to be stored. For
example, if the data should be transferred to a folder “sys\scan” of NetWare server, enter “\sys\scan”.
LOGIN USER NAME: Press this to enter a user name to login NetWare server. Enter this as required.
PASSWORD: Press this to enter a password to login NetWare server. Enter this as required.
Performing Copy & File 81
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
4.
EDITING FUNCTIONS
This chapter describes how to use various copying functions on the EDIT menu.
Image Shift.............................................................................................................................. 85
Creating top/bottom margin or left/right margin....................................................................................................85
Dual Page................................................................................................................................ 92
Job Build............................................................................................................................... 113
TAB EXTENSION...............................................................................................................................................123
COPIED TAB INSERT........................................................................................................................................128
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
Displaying EDIT Menu
You can display the EDIT menu by pressing the [EDIT] tab on the touch panel when you want to use various editing
functions.
The EDIT menu has 2 pages. To switch the pages, press
or
.
84 Displaying EDIT Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
Image Shift
You can create a binding margin by shifting an image to the left, right, top or bottom of the copy paper. This function is
called “image shift”. It is useful when you wish to punch or staple a stack of paper after copying it. With this function you
can easily make a binding margin when you copy a book-type original on both sides of the paper.
You can make a binding margin in the combinations as follows:
y Top/bottom margin and left/right margin
y Top/bottom margin and bookbinding margin
„ Creating top/bottom margin or left/right margin
Place paper in the drawer(s).
When using bypass copying, be sure to set the paper size.
1
Place the original(s).
2
Press [IMAGE SHIFT] on the EDIT menu.
3
Select the type of binding margin.
4
Image Shift 85
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
Adjust the width of the binding margin.
1) Press [FRONT MARGIN] and adjust the binding margin width on the front side using [ 2 mm] and [ 100
mm].
5
2) Press [BACK MARGIN] and adjust the binding margin width on the back side using [ 2 mm] and [ 100 mm].
3) Press [OK].
Note that a left/right binding margin will be created on the opposite side on the back side of paper in duplex
copying. (For example, when a binding margin is created on the right of the front side of the paper, it will be
created on the left of the back side.)
Press [OK].
6
7
Select other copy modes as required, and then press the [START] button on the control
panel.
86 Image Shift
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
4.EDITING FUNCTIONS
„ Creating bookbinding margin
You can easily make a binding margin when you copy a book-type original on both sides of the paper.
Press [IMAGE SHIFT] on the EDIT menu.
1
Press [BOOK].
2
Adjust the width of the binding margin.
1) Press either [ 2 mm] (0.08") or [ 30 mm] (1.18").
2) Press [OK].
3
Image Shift 87
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
Press [OK].
4
Select the “Book-type original -> 2-sided copy” mode as well.
88 Image Shift
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
Edge Erase
You can whiten the edge of the copied image when a shadow-like dark part appears on it. This function is called “edge
erase”. It is useful when you want to make the copied image neat and clear if the edge of the original is dirty or torn.
Only standard size originals are applicable.
Place paper in the drawer(s).
When using bypass copying, be sure to set the paper size.
1
Place the original(s).
2
Press [EDGE ERASE] on the EDIT menu.
3
Adjust the width of the part to be erased.
1) Press either [ 2 mm] (0.08") or [ 50 mm] (1.97").
2) Press [OK].
4
Select other copy modes as required, and then press the [START] button on the control
panel.
5
Edge Erase 89
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
Book Center Erase
You can whiten the center of the copied image when a shadow-like part appears on it. This function is called “book center
erase”. It is useful when you copy book-type originals.
No setting
Book center erase set
Place paper in the drawer(s).
When using bypass copying, be sure to set the paper size.
1
2
Select the drawer for the desired paper size.
Press [BOOK CENTER ERASE] on the EDIT menu.
3
90 Book Center Erase
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
4.EDITING FUNCTIONS
Adjust the width of the part to be erased.
1) Press either [ 2 mm] (0.08") or [ 50 mm] (1.97").
2) Press [OK].
4
Place the original on the original glass.
Place the original with its bottom toward you, matching its center to the
yellow indicator under the original glass.
5
Do not place any heavy objects (4 kg (9 lb.) or over) on the original glass and do not press on it with
force.
Breaking the glass could injure you.
Select other copy modes as required, and then press the [START] button on the control
panel.
6
Book Center Erase 91
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
Dual Page
You can copy the 2 facing pages of a book-type original or 2 original sheets placed side by side onto 2 separate sheets of
paper or on both sides of 1 sheet of paper. This function is called “dual page”. You do not have to shift the original on the
original glass.
-12-
-13-
-12-
-13-
Only A4, B5 and LT sizes are applicable.
Place paper in the drawer(s).
1
2
Press [DUAL PAGE] on the EDIT menu.
Press [1 SIDE] or [2 SIDE].
1 SIDE: Copying the 2 facing pages of the original to only 1 side of 2 separate sheets of paper
2 SIDE: Copying the 2 facing pages of the original to 2 sides of 1 sheet of paper
3
Select other copy modes as required.
You can select “image shift” as well.
4
92 Dual Page
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
4.EDITING FUNCTIONS
Press the [BASIC] tab to display the BASIC menu, and then select A4, B5 or LT as the
copy paper size.
5
6
When using bypass copying, be sure to set the paper size.
Open the desired page of the original and place it on
the original glass.
Place the original with its bottom toward you, matching its center to the
yellow indicator under the original glass.
Do not place any heavy objects (4 kg (9 lb.) or over) on the original glass and do not press on it with
force.
Breaking the glass could injure you.
Press the [START] button on the control panel. When the scanning of the opened pages
is finished, open the next pages and place them.
Repeat this procedure until all the desired pages have been scanned. If the last page is a single page, press
[COPY FINAL PAGE] on the touch panel, and then press the [START] button on the control panel to start scanning.
The scanned pages will be copied.
7
When all the pages have been scanned, press [FINISHED].
The scanned pages will be copied.
8
Dual Page 93
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
2IN1 / 4IN1
You can copy 2 or 4 originals to 1 sheet of paper by shrinking them. This function is called “2IN1” or “4IN1”. If you use this
function together with duplex copying, you can make a total of 8 images on 1 sheet of paper.
The illustrations below show how you can arrange the images.
2IN1
4IN1
2IN1 & duplex copying (a: side 1, b: side 2)
a
a
b
b
4IN1 & duplex copying (a: side 1, b: side 2)
a
b
94 2IN1 / 4IN1
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
4.EDITING FUNCTIONS
Place paper in the drawer(s).
When using bypass copying, be sure to set the paper size.
1
If you select paper of a different size to that of the original, press [ZOOM] on the BASIC menu. Then select the
desired paper size and press [AMS] in the menu shown below.
Place the original(s).
2
3
Press [2IN1 / 4IN1] on the EDIT menu.
Perform 2IN1 / 4IN1 setting.
NUMBER OF PAGES PER SHEET: If you want to copy 2 originals on 1 page, select [2IN1]. If you want 4 on 1
4
page, select [4IN1].
2-SIDED: Select from [1->1 SIMPLEX], [1->2 DUPLEX], [2->2 DUPLEX] or [2->1 SPLIT].
Press [OK] after you have selected all the necessary items.
2IN1 / 4IN1 95
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
Select other copy modes as required, and then press the [START] button on the control
panel.
When the originals are placed on the RADF, scanning and copying start. When they are placed on the original
glass, follow steps 6 and 7.
5
6
7
Place the next original, and then press the [START] button on the control panel.
Scanning of the next original starts. The scanning also starts when you press [YES] on the touch panel and then
the [START] button on the control panel. If you have more than one original, repeat this step until the scanning of all
the originals is finished.
When the scanning of all the originals is finished, press [FINISHED] on the touch panel.
Copying starts.
96 2IN1 / 4IN1
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
Magazine Sort Mode
You can copy more than one original in the book-type page order. This mode is called the magazine sort mode. Also you
can do this as well as fold and staple the copied sheets at their center. This mode is called the magazine sort & saddle
stitch mode.
Magazine sort mode
1
6
7
2
4
9
3
2
11
12
Magazine sort & saddle stitch mode
1
2
6
7
3
12
The magazine sort mode can also be selected on the BASIC menu. For details, see the following page:
Place paper in the drawer(s).
Sizes are available as follows:
1
Magazine sort: A3, A4-R, A5-R, B4, B5-R, LD, LG, LT-R, ST-R
Magazine sort & saddle stitch: A3, A4-R, B4, LD, LG, LT-R
Select the paper size.
2
Drawer:
Bypass tray:
Place the original(s).
3
When placing portrait originals in a landscape direction as shown
on the right in the magazine sort mode or the magazine sort &
saddle stitch mode, set the image direction function to ON on the
EDIT menu. Otherwise the originals will not be copied in the proper
page order.
Magazine Sort Mode 97
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
Press [MAGAZINE SORT] on the EDIT menu.
4
Set the saddle stitch mode and the binding margin width as required.
1) When setting the saddle stitch mode, press [STAPLE ON]. If not required, press [STAPLE OFF].
5
2) Press either [ 2 mm] (0.08") or [ 30 mm] (1.18") to adjust the binding margin width.
3) Press [OK].
For the maximum number of sheets available for saddle stitching, see the following page:
Select other copy modes as required, and then press the [START] button on the control
panel.
6
98 Magazine Sort Mode
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
Image Editing
You can select the various editing functions shown below for scanned images.
Trimming: You can select a certain area of an original and copy only the selected area.
Masking: You can mask a certain area of an original and copy only the unmasked area.
Mirror image: You can reverse a page like a mirror.
Negative/Positive reversal: You can reverse the black-and-white of a page.
„ Trimming / Masking
You can select the desired area of an original and copy only the selected area (trimming). You can also mask the desired
area of an original and copy only the unmasked area (masking). On both functions you can select up to 4 areas on 1
original. The selected area should be in a rectangle.
Trimming
Masking
y Only standard size originals are applicable.
y Note that the entire image of the selected area may not be copied if you do not select proper sizes for the original
and copy paper.
Place paper in the drawer(s).
When using bypass copying, be sure to set the paper size.
1
Press [EDITING] on the EDIT menu.
2
Image Editing 99
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
Press [TRIM] or [MASK].
3
Place the original on the original glass with its face
up.
Place it with its bottom toward you. Match its top left corner against that
of the original glass so that the original will be aligned with the original
scales.
4
Do not place any heavy objects (4 kg (9 lb.) or over) on the original glass and do not press on it with
force.
Breaking the glass could injure you.
Read the following 4 values to specify the area using
the left and top scales on the original glass.
5
X1: From the top left to the left edge of the selected area
X2: From the top left to the right edge of the selected area
Y1: From the top left to the upper edge of the selected area
Y2: From the top left to the lower edge of the selected area
Note that the marks of the original scales have a 2 mm (0.08") pitch.
100 Image Editing
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
4.EDITING FUNCTIONS
Key in the read values.
1) Press [X1], [X2], [Y1] and [Y2], and then key in the read values correspondingly.
6
2) You can specify up to 4 areas on 1 page. When you want to specify more than one area, press
switch the area, and then key in the values correspondingly.
or
to
3) Press [OK] after you have specified all the areas.
Place the original again on the original glass with its
face down.
Place it with its bottom toward you. Match its top left corner against that
of the original glass.
7
8
Select other copy modes as required, and then press the [START] button on the control
panel.
Image Editing 101
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
„ Mirror image / Negative/Positive reversal
You can reverse a page like a mirror (mirror image), or you can reverse the black-and-white of a page (negative/positive
reversal).
Negative/Positive reversal
Mirror image
Place paper in the drawer(s).
When using bypass copying, be sure to set the paper size.
1
Place the original(s).
2
3
Press [EDITING] on the EDIT menu.
Press [MIRROR] or [NEG/POS].
4
5
Select other copy modes as required, and then press the [START] button on the control
panel.
102 Image Editing
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
XY Zoom
You can change the reproduction ratio in both vertical and horizontal directions separately. This function is called “XY
zoom”.
100%
200%
100%
200%
The reproduction ratio is changeable from 25 to 400%. However when the original is placed on the RADF (Reversing
Automatic Document Feeder), this range is 25 to 200%.
Place paper in the drawer(s).
When using bypass copying, be sure to set the paper size.
1
Place the original(s).
2
Press [XY ZOOM] on the EDIT menu.
3
Set the reproduction ratio in both vertical and horizontal directions.
1) Press [X], and then press either [ 25%] or [ 400%] for a horizontal direction.
4
2) Press [Y], and then press either [ 25%] or [ 400%] for a vertical direction.
3) Press [OK].
Select other copy modes as required, and then press the [START] button on the control
panel.
5
XY Zoom 103
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
Cover Sheet
You can add a special type of paper such as colored paper as a front cover sheet or a back cover sheet. This function is
called “cover sheet”. The cover sheet mode has the following 4 types:
TOP BLANK: Adds a blank sheet as a front cover.
1
2
3
TOP COPIED: Adds a copied sheet as a front cover.
2003
REPORT
REPORT
2003
1
2
3
BOTH BLANK: Adds 2 blank sheets as a front cover and a back cover.
1
2
3
TOP COPIED BACK BLANK: Adds a copied sheet as a front cover and a blank sheet as a back cover.
REPORT
2003
2003
REPORT
1
2
3
Place the paper for the cover sheets.
Place it on the bypass tray or in a drawer previously set for cover sheets. The paper for the cover sheets must be
placed in a different paper source than normal paper.
1
When the Inserter (optional) is installed in the equipment
For using [TOP BLANK] or [BOTH BLANK] in the cover sheet modes, paper for cover sheets can be set on the
Inserter.
You can use [TOP BLANK] or [BOTH BLANK] with a function for inserting a back cover sheet turned down,
using the [INSERTER] function.
104 Cover Sheet
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
4.EDITING FUNCTIONS
y When placing paper for cover sheets in a drawer, set the paper type (“COVER”), size and thickness for the
drawer.
y When placing paper for cover sheets on the bypass tray, set the size and thickness.
y Place the paper for cover sheets of the same size as normal paper in the same direction.
Place the normal paper in the drawer(s).
2
3
Place the original(s).
When placing them on the original glass, they must be placed from the first page.
Press [COVER SHEET] on the EDIT menu.
4
Select the desired cover sheet mode.
5
When you select [TOP COPIED] or [TOP COPIED BACK BLANK] and [1->2 DUPLEX] (duplex copying)
together, the front cover will be a 1-sided copy.
Cover Sheet 105
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
Press the [BASIC] tab to display the BASIC menu. Then select a drawer in which
normal paper is placed (not the one for the cover sheets).
6
You must place the normal paper of the same size and direction as that for the cover sheets in advance.
Select other copy modes as required, and then press the [START] button on the control
panel.
When the originals are placed on the RADF, scanning and copying start.
When they are placed on the original glass, follow steps 8 and 9.
7
8
9
Place the next original, and then press the [START] button on the control panel.
Scanning of the next original starts. The scanning also starts when you press [YES] on the touch panel and then
press the [START] button on the control panel. Repeat this procedure until the scanning of all the originals is
finished.
When the scanning of all the originals is finished, press [FINISHED] on the touch panel.
Copying starts.
106 Cover Sheet
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
Sheet Insertion
You can insert a special type of paper such as colored paper at the desired page. This function is called “sheet insertion”.
You can insert up to 2 types of sheets for a total of 50 pages. The sheet insertion mode has the following 2 types:
COPIED: Inserts a copied sheet, replacing the specified page.
1
1
2
2
03
REP
3
4
3
REPORT
2003
4
BLANK: Inserts a blank sheet before the specified page.
1
2
3
Place the paper for sheet insertion.
Place it on the bypass tray or in a drawer previously set for insertion sheets. The paper for the insertion sheets
must be placed in a different paper source than normal paper.
1
When the Inserter (optional) is installed in the equipment
For using [BLANK] in the sheet insertion modes, paper for sheet insertion can be set also on the Inserter.
You can use [BLANK] in combination with a function for inserting front and back cover sheets with the
[INSERTER] function.
y When placing paper for insertion sheets in a drawer, set the paper type (“INSERT 1” or “INSERT 2”), size
and thickness for the drawer.
y When placing paper for insertion sheets on the bypass tray, set the size and thickness.
y Place the paper for insertion sheets of the same size as normal paper in the same direction.
Place the normal paper in the drawer(s).
2
3
Place the original(s).
When placing them on the original glass, they must be placed from the first page.
Sheet Insertion 107
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
Press [SHEET INSERTION] on the EDIT menu.
4
5
6
Press either [COPIED] or [BLANK].
Select the page where the insertion sheets will be inserted.
1) Select the type of the insertion sheets ([INSERT SOURCE 1] or [INSERT SOURCE 2]).
2) Key in page numbers (1 to 2000) where the insertion sheets will be inserted, and then press [SET]. Repeat
steps 1) and 2) if you want to insert sheets at more than one page.
3) Press [OK] after you have keyed in the page numbers.
y If you selected [COPIED] in step 5, the selected page will be replaced with a copied insertion sheet. If you
selected [BLANK], a blank insertion sheet will be inserted before the selected page.
y Up to 50 pages in total can be selected for [INSERT SOURCE 1] and [INSERT SOURCE 2].
108 Sheet Insertion
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
4.EDITING FUNCTIONS
Press the [BASIC] tab to display the BASIC menu. Then select the drawer in which
normal paper is placed (not the one for sheet insertion).
7
You must place the normal paper of the same size and direction as that for the insertion sheets in advance.
Select other copy modes as required, and then press the [START] button on the control
panel.
8
When the originals are placed on the RADF, scanning and copying start.
When they are placed on the original glass, follow steps 9 and 10.
Place the next original, and then press the [START] button on the control panel.
Scanning of the next original starts. The scanning also starts when you press [YES] on the touch panel and then
the [START] button on the control panel. Repeat this procedure until the scanning of all the originals is finished.
9
When the scanning of all the originals is finished, press [FINISHED] on the touch panel.
Copying starts.
10
Sheet Insertion 109
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
Time Stamp
You can add the date and time on the copied paper.
Printed at the bottom
of a portrait copy
Printed at the top
of a landscape copy
MM.DD.YYYY 14:54
MM.DD.YYYY 14:54
Place paper in the drawer(s).
Place the original(s).
1
2
3
Press [TIME STAMP] on the EDIT menu.
Select the direction and position of the time stamp.
4
1) Select the direction ([SHORT EDGE] or [LONG EDGE]).
2) Select the position ([UPPER] or [LOWER]).
3) Press [OK].
Select other copy modes as required, and then press the [START] button on the control
panel.
5
110 Time Stamp
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
Page Number
You can add a page number on the copied paper.
Printed at the bottom center
of a portrait copy
Printed at the top right
of a landscape copy
1
2
3
1
2
3
Place paper in the drawer(s).
1
2
3
Place the original(s).
Press [PAGE NUMBER] on the EDIT menu.
Select the direction and position of a page number.
1) Select the direction ([SHORT EDGE] or [LONG EDGE]).
2) Select the position ([TOP LEFT], [TOP CENTER], etc.).
4
3) If you want to specify the page number to start with, press
to step 6.
and go to step 5. Otherwise, press [OK] and go
Page Number 111
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
Specify the page number you want to start with.
1) Key in the page number.
2) Press [OK].
5
Select other copy modes as required, and then press the [START] button on the control
panel.
6
112 Page Number
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
Job Build
You can scan several stacks of originals whose settings are individually different, and then copy or store them in one
operation. This function is called “job build”. For example, news clips (in the TEXT mode) and photographs in magazines
(in the PHOTO mode) in A3 size and photographs in A4 size can be scanned in the optimal settings for each, and copied
in one operation.
y Up to 2000 pages of originals can be copied in one operation. There is no limit for the number of jobs.
y Some settings are not available for job build, and some settings for the first job will be applied to all of the other
jobs. See the table below before setting job build.
Settings not available
Settings applied for all jobs
Settings changeable for each job
Automatic Paper Selection
BOOK -> 2 (Book-type original -> 2-
sided copy)
Editing
XY zoom
e-Filing / File
Reproduction ratio
Mixed-size originals
Copy paper size
Finishing mode
Image shift
Automatic Magnification Selection
(Default setting for job build)
Original size
Original mode
Cover sheet
Sheet insertion
Magazine sort
Magazine sort & saddle stitch
2IN1 / 4IN1
Tab paper
Book center erase
Time stamp
Page number
Image direction
Book - tablet
Simplex/Duplex copying settings
other than Book-type original -> 2-
sided copy (1->1 SIMPLEX, 2->1
SPLIT, 1->2 DUPLEX, 2->2 DUPLEX)
Background adjustment
Sharpness
Inserter
Edge erase
Dual page
Document feeder (Feeding mode)
Press [JOB BUILD] on the EDIT menu.
1
Job Build 113
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
Press [OK].
2
Job build is now set and the message below appears.
Place the first stack of originals, and then select settings.
3
y When placing the original on the original glass, remember that 1 page is equal to 1 job.
y When placing mixed-size originals on the RADF, see the following page:
y If you want to use a particular drawer, select it.
y Press [SETTINGS] on the touch panel to confirm the current settings.
y If you want to change the settings, press the [FUNCTION CLEAR] button on the control panel, and then
restart the procedure from step 1.
114 Job Build
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
4.EDITING FUNCTIONS
Press the [START] button on the control panel.
Scanning starts. When the scanning of all the originals is finished, the message below appears.
4
Place the next stack of originals, and then select the settings.
Repeat steps 4 and 5 until all the desired pages have been scanned.
5
6
If you do not change any settings, those for the last job will be applied.
When the scanning of all the originals is finished, change the number of copy sets as
required. Then press [JOB FINISH] on the touch panel.
Copying starts. If any storing function is set, storing also starts.
Job Build 115
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
Image Direction
When you make 1-sided portrait originals to 2-sided copy by placing them in a landscape direction, normally the copied
pages are “open to top”. With this function you can make them “open to left”. This function is called “image direction”.
When you make 2-sided “open to left” portrait originals to 1-sided copy, normally the copied pages exit in a different
direction alternately. With this function, you can make them all exit in the same direction.
1-sided portrait original (placed in a landscape direction) -> 2-sided copy
“IMAGE DIRECTION” set
No setting
2-sided “open to left” portrait original -> 1-sided copy
“IMAGE DIRECTION” set
No setting
Place paper in the drawer(s).
Place the original(s).
1
2
3
Set duplex copying setting.
Press [IMAGE DIRECTION] on the EDIT menu.
4
116 Image Direction
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
4.EDITING FUNCTIONS
Press [OK].
5
Image direction is now set.
Select other copy modes as required, and then press the [START] button on the control
panel.
6
Image Direction 117
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
Book - Tablet
As for the directions of originals or copied images, “open to left” is called “book” and “open to top” is called “tablet”. With
this function you can make 2-sided originals to 2-sided copy, rotating only the back side of the copied page by 180
degrees, namely, you can copy “book” originals to “tablet” copy, or vice versa.
Place paper in the drawer(s).
1
Place the original(s).
2
Press [BOOK <->TABLET] on the EDIT menu.
3
Press [OK].
4
Book - tablet is now set.
Select other copy modes as required, and then press the [START] button on the control
panel.
5
118 Book - Tablet
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
ADF -> SADF
You can switch the feeding mode when the RADF (Reversing Automatic Document Feeder) is used, from “ADF” to
“SADF”. The paper feeding mode has 2 types as follows:
ADF (Continuous feed mode): Feeds originals continuously when you press the [START] button on the control panel
while originals are being placed on the RADF. This is useful when you make more than one copy in one operation.
(Default setting)
SADF (Single feed mode): Feeds originals one by one automatically. This is useful when you usually only have 1 original.
When the single feed mode (SADF) is set, place originals one sheet at a time. If you place more than one original, the
copied image may be skewed or the originals may jam.
Place paper in the drawer(s).
1
Press [ADF -> SADF] on the EDIT menu.
2
Press [OK].
3
The feeding mode is now set at “single feed mode”.
Select other copy modes as required.
4
ADF -> SADF 119
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
Place the original(s) on the RADF one sheet at a time.
The original is pulled into the RADF automatically, and then the menu below appears.
5
Repeat step 5 if you have another original. The placed original will be pulled into the RADF automatically even if
you do not press [YES] on the touch panel.
When the scanning of all the originals is finished, press [FINISHED].
6
Even if you do not press [FINISHED], copying will start when the current operation is cleared by means of the
automatic function clear.
120 ADF -> SADF
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
Tab Paper
Copying on the tab of tab paper and inserting tab paper in copying can be performed. There are the following 3 modes:
COPY ON TAB: Copying on the tab on the tab paper
BLANK TAB INSERT: Inserting blank tab paper at a specified page
COPIED TAB INSERT: Copying on the tab paper and inserting the copied tab paper at the specified pages
COPY ON TAB
BLANK TAB INSERT
COPIED TAB INSERT
„ Preparing an original to copy on the tab paper
Prepare an original for making a copy on tab paper using [COPY ON TAB] or [COPIED TAB INSERT]. The index of the
original is copied on the tab of tab paper by having the printing position shifted as follows. Use an A4/LT-original.
Shift width
(
Distance the image is
shifted in copying on tab paper
)
Tab width
Original
Tab paper
„ Setting tab paper
Set tab paper in a drawer other than the External Large Capacity Feeder or the bypass tray (the second drawer is
recommended).
The setting order of tab paper is different between when setting it in the drawer and when setting it on the bypass tray.
y Only A4 and LT-size tab paper can be used.
y When an optional finisher is installed, use 5-tab or 8-tab paper.
‰ Setting tab paper in a drawer
Pull out the drawer.
1
Insert the tab paper back guide into the slit of A4-TAB
(LT-TAB) in the drawer.
2
Tab Paper 121
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
Match the order of the tab paper with that of the originals.
3
4
Originals
Sheets of tab paper
Front
side
1st
2nd
1st
2nd
3rd
4th
3rd
4th
Place the tab paper with its face down in the drawer.
1st
2nd
3rd
4th
Back side
Close the drawer.
5
6
Set [TAB] for the paper type of the drawer.
‰ Setting tab paper on the bypass tray
Match the order of the tab paper with that of the originals.
1
Originals
Sheets of tab paper
Front
side
1st
2nd
1st
2nd
3rd
4th
3rd
4th
Place the tab paper with its face up on the bypass
tray.
2
3
Front side
Set [TAB PAPER] for the paper type of the bypass tray.
122 Tab Paper
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
4.EDITING FUNCTIONS
„ TAB EXTENSION
Set the tab width and shift width of tab paper. These must be set before performing [COPY ON TAB], [BLANK TAB
INSERT] or [COPIED TAB INSERT].
Press [TAB PAPER] on the EDIT menu.
1
Press [TAB EXTENSION].
2
Adjust the tab width and shift width.
1) Press [DRAWER] for setting tab paper in the drawer or [BYPASS FEED] for setting it on the bypass tray.
3
2) Press [TAB EXTENSION] to adjust the tab width using
or
or
.
3) Press [SHIFT MARGIN] to adjust the shift width using
4) Press [OK].
.
Though the initial value is set to 13 mm (0.5") for both the tab width and shift width, this can be changed. For
details, refer to the MFP Management Guide.
Tab Paper 123
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
Range of the tab width and shift width
The tab width and shift width can be set in the following ranges. They are different when the tab paper is set in the
drawer and on the bypass tray.
Tab width
Shift width
Drawer
12 - 17 mm (0.4" - 0.6")
10 - 20 mm (0.4" - 0.7")
0 - 30 mm (0 - 1.1")
0 - 30 mm (0 - 1.1")
Bypass tray
Measuring the tab width and shift width on the original glass
The tab width and shift width can be measured by the scale on the left and rear side of the original glass. The
marks of the original scale have a 2 mm (0.08") pitch.
Measuring the tab width
Place tab paper on the original glass to measure the tab width.
Tab width
Original scale
Aligned with the scale
Measuring the shift width
Place the original on the original glass to measure the shift width.
Shift width
Original scale
Aligned with
the scale
„ COPY ON TAB
The original is copied on the tab paper.
Set the tab width and shift width using [TAB EXTENSION] in advance.
Prepare and place the original to copy on the tab paper.
1
Place tab paper.
2
124 Tab Paper
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
4.EDITING FUNCTIONS
Press [TAB PAPER] on the EDIT menu.
3
4
5
Press [COPY ON TAB].
Press [OK].
Tab Paper 125
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
Press [OK].
6
Select other copy modes as required, and then press the [START] button on the control
panel.
7
„ BLANK TAB INSERT
Blank tab paper is inserted at the specified pages. Copying is not performed on the tab paper.
Set the tab width using [TAB EXTENSION] in advance.
Place tab paper.
1
Place the original(s).
2
Press [TAB PAPER] on the EDIT menu.
3
126 Tab Paper
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
4.EDITING FUNCTIONS
Press [BLANK TAB INSERT].
4
Set the pages to insert tab paper.
1) Key in the page number (1 to 2000) for inserting the tab paper, and then press [SET]. If more than one sheet of
5
tab paper is inserted, repeat this procedure.
2) After the page number has finished being keyed in, press [OK].
In [BLANK TAB INSERT], blank tab paper is inserted at the specified pages. Up to 50 sheets of tab paper can
be inserted.
Press [OK].
6
7
Select other copy modes as required, and then press the [START] button on the control
panel.
Tab Paper 127
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
„ COPIED TAB INSERT
Tab paper is inserted at the specified pages and copying is performed also on the Tab paper.
Set the tab width and shift width using [TAB EXTENSION] in advance.
Prepare the original to copy on the tab paper.
1
Place tab paper.
2
Place the original(s).
3
Insert the original for the tab paper prepared in step 1 at the desired page of the other originals and place them.
Press [TAB PAPER] on the EDIT menu.
4
Press [COPIED TAB INSERT].
5
128 Tab Paper
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
4.EDITING FUNCTIONS
Set the pages to insert tab paper.
1) Key in the page number (1 to 2000) for inserting the tab paper, and then press [SET]. If more than one sheet of
6
tab paper is inserted, repeat this procedure.
2) After the page number has finished being keyed in, press [OK].
y In [COPIED TAB INSERT], a copy is made on tab paper and it is inserted at the specified pages. Up to 50
sheets of tab paper can be inserted.
y Check that the page number corresponds to the inserted page for tab paper in step 3.
Press [OK].
7
8
Select other copy modes as required, and then press the [START] button on the control
panel.
Tab Paper 129
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
Inserter
You can insert the paper placed on the Inserter (optional) as a front or back cover sheet, or insert the paper at the
specified pages. There are 3 types of sheet insertion as follows.
FRONT COVER: Inserting paper as a front cover sheet
FRONT & BACK COVER: Inserting paper as front and back cover sheets
SHEET INSERT: Inserting paper at the specified pages
y [FRONT COVER] or [FRONT & BACK COVER] can be used in combination with [SHEET INSERT].
y In the [FRONT & BACK COVER], the sheet for the back cover can be inserted with its back side facing up. Refer to
the MFP Management Guide for details.
y The inserted sheets are not copied in this function. If you want to make copies on them, use the cover sheet mode
or sheet insertion mode. In that case, place them in the drawer or on the bypass tray of the equipment.
Place paper for the insertion sheet on the Inserter.
1
Place plain paper in the drawer.
2
Press [INSERTER] on the EDIT menu.
3
Press [PAPER TYPE].
4
If [MEDIA TYPE] and [PAPER SIZE] are not displayed, place the paper on the Inserter correctly.
130 Inserter
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
4.EDITING FUNCTIONS
Select and press the type corresponding to the paper placed on the Inserter.
5
6
7
Press [PAPER SIZE].
Select and press the size corresponding to the paper placed on the Inserter.
Inserter 131
Download from Www.Somanuals.com. All Manuals Search And Download.
4 EDITING FUNCTIONS
Set the sheet insertion type.
1) Press [FRONT COVER], [FRONT & BACK COVER] or [SHEET INSERT].
2) If [SHEET INSERT] is selected, key in the desired page number (1 to 2000). To specify more than one page,
8
press
or
to switch the sheet and repeat this procedure.
3) After you have finished the setting, press [OK].
y [FRONT COVER] or [FRONT & BACK COVER] can be used in combination with [SHEET INSERT].
y In [SHEET INSERT], a blank sheet is inserted before the page specified. Up to 50 pages can be specified.
Select other copy modes as required, and then press the [START] button on the control
panel.
9
132 Inserter
Download from Www.Somanuals.com. All Manuals Search And Download.
5.
IMAGE ADJUSTMENT
This chapter describes the image adjustment functions of this equipment.
Displaying IMAGE Menu...................................................................................................... 134
Using Image Adjustment Functions................................................................................... 135
Download from Www.Somanuals.com. All Manuals Search And Download.
5 IMAGE ADJUSTMENT
Using Image Adjustment Functions
„ Background adjustment
This function allows you to adjust the density of the original’s background. It avoids the back side of a 2-sided original
becoming visible on its front side.
Adjusted to have
a lightened
background
Front
Back
Not adjusted
This mode cannot be used with the automatic density adjustment function.
Press [BACKGROUND ADJUSTMENT] in the IMAGE menu.
1
Press [LIGHT] or [DARK] to adjust the density, and then press [OK].
2
Canceling background adjustment
y Move the indicator to the middle, and then press [OK].
y Press [RESET] and then [OK].
Using Image Adjustment Functions 135
Download from Www.Somanuals.com. All Manuals Search And Download.
5 IMAGE ADJUSTMENT
„ Sharpness
This function allows you to emphasize or blur the outline of the image.
Press [SHARPNESS] in the IMAGE menu.
1
2
Press [SOFT] or [SHARP] to adjust the sharpness, and then press [OK].
When the sharpness level is adjusted to the [SOFT] side, the moire fringes on the printed photos, etc. are softened.
If it is adjusted to the [SHARP] side, the letters and fine lines become sharper.
Canceling sharpness adjustment
y Move the indicator to the middle, and then press [OK].
y Press [RESET] and then [OK].
136 Using Image Adjustment Functions
Download from Www.Somanuals.com. All Manuals Search And Download.
6.
TEMPLATES
This chapter describes how to use templates.
Displaying template menu..................................................................................................................................138
Using “Useful templates”....................................................................................................................................139
Registering Templates......................................................................................................... 141
Registering templates into a private group.........................................................................................................145
Changing Data...................................................................................................................... 150
Download from Www.Somanuals.com. All Manuals Search And Download.
6 TEMPLATES
Templates
You can create a template with several functions that are frequently used so that they can be employed whenever you
want by recalling the template, thus eliminating the need to perform complicated settings every time. Templates can be
used in copying, scanning and sending a fax.
Fax functions are available only when the Fax Unit (optional) is installed.
2009.5.5
.5.5
1
+
+
=
1
„ Displaying template menu
You can display the template menu by pressing [TEMPLATE] on the touch panel when you want to register or recall
templates.
138 Templates
Download from Www.Somanuals.com. All Manuals Search And Download.
6 TEMPLATES
6.TEMPLATES
„ Using “Useful templates”
This equipment has 12 default templates that can be used immediately. They are registered to the group number 001
“Useful templates”. For how to recall them, see the following page:
Templates with copying functions
Function *1
Button
Original size: 2-sided small originals, such as business cards
Paper size: A4 (equipment for the A/B format), LT (equipment for the LT format)
2IN1 / 4IN1: 2IN1
(Place the original on the original glass before recalling the template since the automatic start is
enabled in this template. After scanning the front side and then the back of the 2-sided original, press
[FINISHED] to start copying.)
2IN1 / 4IN1: 2IN1
Simplex/Duplex: 2 -> 2 DUPLEX
Staple: FRONT STAPLE *2
Original size: Mixed-size
Paper selection: Automatic Paper Selection
Staple: FRONT STAPLE *2
Original size: Mixed-size
Paper selection: Automatic Magnification Selection
Paper source: 1st drawer
Staple: FRONT STAPLE *2
Original size: 1-sided
Finishing mode: Magazine sort & saddle stitch
Editing method: Cover sheet (Top blank) *2, *3
(Place the paper in the 1st drawer and the paper for the cover sheet on the inserter. Both of them must
be the same size and direction. If you are using a landscape original, place it vertically.)
Templates with scanning functions
Button
Function *1
Original: 2-sided
Original mode: Image smoothing
Resolution: 200 dpi
Storing method: Stored in a shared folder as a PDF file (multi) *4
Original: 1-sided
Original mode: Image smoothing
Resolution: 300 dpi
Storing method: Stored in the e-Filing box (public box) *4
Original: 1-sided
Original mode: Image smoothing
Resolution: 200 dpi
Storing method: Stored in a shared folder as a PDF file (multi) *4
Templates 139
Download from Www.Somanuals.com. All Manuals Search And Download.
6 TEMPLATES
Templates with e-Filing functions
Button
Function *1
Original mode: TEXT/PHOTO
Simplex/Duplex: 1 -> 1 SIMPLEX
Storing method: Stored in the e-Filing box (public box)
Original mode: TEXT/PHOTO
Simplex/Duplex: 2 -> 1 SPLIT
Storing method: Stored in the e-Filing box (public box)
Original mode: TEXT/PHOTO
Simplex/Duplex: 1 -> 2 DUPLEX
Storing method: Stored in the e-Filing box (public box)
Original mode: TEXT/PHOTO
Simplex/Duplex: 1 -> 1 SIMPLEX
Editing function: Dual page
Storing method: Stored in the e-Filing box (public box)
(The dual page function is available only for A4, LT and B5 sizes.)
*1 Functions other than those noted here are in their default settings.
*2 An optional finisher is required for stapling and saddle stitching. If a finisher is not installed, the printed paper is only sorted.
*3 The Inserter (optional) is required.
*4 The Scanner Kit (optional) or Printer/Scanner Kit (optional) is required.
140 Templates
Download from Www.Somanuals.com. All Manuals Search And Download.
6 TEMPLATES
Registering Templates
Templates must be registered to either the “public template group” or “private groups”. You can set a password to restrict
the use of registered templates.
Public template group:
Provided by default. Templates in this group can be used by everyone. It is useful to register several combinations of
functions frequently used in the entire office or department. Up to 60 templates can be registered to the public group. The
Admin (administrator) Password is required when you wish to register, delete or change templates in the public template
group.
Private group:
You can create up to 200 private groups. These are useful for each department, section or user. Up to 60 templates can be
registered per group. You can set a password to restrict the use of the registered templates. “Useful templates” are
registered under the group 001 by default.
„ Registering templates into the public template group
Set all the required functions.
Example: Editing function – image shift, reproduction ratio – 90%, number of copy sets –10
1
Press [TEMPLATE] on the touch panel.
2
The template menu appears.
Select the public template group.
1) Press the [REGISTRATION] tab.
2) Press [PUBLIC TEMPLATE GROUP].
3) Press [OPEN].
3
Registering Templates 141
Download from Www.Somanuals.com. All Manuals Search And Download.
6 TEMPLATES
Press [PASSWORD].
4
The on-screen keyboard appears.
Enter the Admin Password using the on-screen keyboard or the digital keys. Then
press [OK].
5
When you enter the wrong Admin Password 3 times consecutively, this equipment will be locked for 30
seconds. In this case, wait until it is unlocked and then enter the correct password.
Select a template.
1) Press a blank button.
2) Press [SAVE].
6
To switch the menu
Press
or
.
142 Registering Templates
Download from Www.Somanuals.com. All Manuals Search And Download.
6 TEMPLATES
6.TEMPLATES
Enter the necessary information about the template.
7
NAME 1 & 2: Enter the name of the template. NAME 1 appears above the template button and NAME 2 appears
below. Be sure to enter at least one of them. When you press either of them, the on-screen keyboard appears.
Enter within 11 letters.
The symbols below cannot be used.
; : / \ " = | * < > ? + [ ] , .
USER NAME: Enter the name of the template owner as required. When you press it, the on-screen keyboard
appears. Enter within 30 letters.
PASSWORD: Key in a password here, if you want to require a password to recall the template. When you press it,
the on-screen keyboard appears. Key in following the procedure below.
1) Press [PASSWORD], and then key in a 5-digit password.
The letters keyed in appear as asterisks (*).
2) Press [RETYPE PASSWORD], and then key in the password again.
3) Press [OK].
Press the [CLEAR] button on the control panel to delete the letter keyed in.
AUTOMATIC START: Press [ENABLE] if you want the operation of set functions to start immediately after pressing
a button for the corresponding template. Press [DISABLE] if you do not want it to start until you press the
[START] button on the control panel.
Registering Templates 143
Download from Www.Somanuals.com. All Manuals Search And Download.
6 TEMPLATES
Even when the automatic start function is enabled, you need to enter the user name and password when
recalling the template in the following cases. For details of the User Authentication for Scan to E-mail and the
user management function, ask your administrator.
y When the User Authentication for Scan to E-mail is enabled and the user management function is disabled
y When both the User Authentication for Scan to E-mail and the user management function are enabled, but
the user names and passwords are different
When you have entered all the necessary items, press [SAVE].
The template is now registered and the menu returns to the one immediately before registration.
„ Creating a new private group
Press [TEMPLATE] on the touch panel.
1
The template menu appears.
Select a group.
2
1) Press the [REGISTRATION] tab.
2) Press a blank button.
3) Press [OPEN].
To switch the menu
y Press
or
.
y Key in the group number (3 digits).
144 Registering Templates
Download from Www.Somanuals.com. All Manuals Search And Download.
6 TEMPLATES
6.TEMPLATES
Enter the necessary information about the group.
3
NAME: Enter the name of the group. When you press it, the on-screen keyboard appears. Enter within 20 letters.
Be sure to enter it.
USER NAME: Enter the name of the group owner as required. When you press it, the on-screen keyboard
appears. Enter within 30 letters.
PASSWORD: Key in a password here, if you want to require a password to view the group or register templates
into the group. When you press it, the on-screen keyboard appears. Key in following the procedure below.
1) Press [PASSWORD], and then key in a 5-digit password.
The letters keyed in appear as asterisks (*).
2) Press [RETYPE PASSWORD], and then key in the password again.
3) Press [OK].
Press the [CLEAR] button on the control panel to delete a letter keyed in.
When you have entered all the necessary items, press [OK].
The new group is now registered and the menu moves to the one for registering templates.
Press the [FUNCTION CLEAR] button on the control panel.
The menu returns to the BASIC menu.
4
„ Registering templates into a private group
Set all the required functions.
Example: Editing function – image shift, reproduction ratio – 90%, number of copy sets – 10
1
Registering Templates 145
Download from Www.Somanuals.com. All Manuals Search And Download.
6 TEMPLATES
Press [TEMPLATE] on the touch panel.
2
The template menu appears.
Select the desired group.
3
1) Press the [REGISTRATION] tab.
2) Press the button of the desired group.
3) Press [OPEN].
To switch the menu
y Press
or
.
y Key in the group number (3 digits).
Key in the password for the selected group. (If no password is set, go to step 5.)
1) Key in the password.
2) Press [OK].
4
Register a template following steps 6 and 7 on
5
146 Registering Templates
Download from Www.Somanuals.com. All Manuals Search And Download.
6 TEMPLATES
Recalling Templates
When you recall a template, the functions set in the template will be available automatically. If automatic start function is
enabled, this equipment will automatically start the operation of each function when you press the button for the
corresponding template.
Place paper in the drawer(s).
1
Place the original(s).
2
Press [TEMPLATE] on the touch panel.
3
The template menu appears.
Press the button for the group to which the desired template is registered.
4
To switch the menu
y Press
or
.
y Key in the group number (3 digits).
Recalling Templates 147
Download from Www.Somanuals.com. All Manuals Search And Download.
6 TEMPLATES
Key in the password when you have selected the private group. (If no password is set,
go to step 6.)
5
1) Key in the password.
2) Press [OK].
Press the button for the desired template.
6
To switch the menu
Press
or
.
Templates with the automatic start function enabled can be identified with
. If this mark is displayed, you can
press it to immediately start the operation of the functions set in the template.
Key in the password for the selected template. (If no password is set, go to step 8.)
1) Key in the password.
2) Press [OK].
7
148 Recalling Templates
Download from Www.Somanuals.com. All Manuals Search And Download.
6 TEMPLATES
6.TEMPLATES
Confirm that “Updated the template setting” is displayed on the touch panel.
The message is displayed for approx. 3 seconds.
8
Select other copy modes as required, and then press the [START] button on the control
panel.
9
Recalling Templates 149
Download from Www.Somanuals.com. All Manuals Search And Download.
6 TEMPLATES
Changing Data
You can change the data of templates or private groups that are already registered, such as the template name, user
name, password and setting of the automatic start function.
The data of the public template group can be changed from the TopAccess menu but this cannot be done from the
control panel. For how to change them from the TopAccess menu, refer to the TopAccess Guide.
„ Changing private group data
In the template menu, select the desired group.
1) Press the [REGISTRATION] tab.
2) Press the button for the desired group.
3) Press [EDIT].
1
To switch the menu
y Press
or
.
y Key in the group number (3 digits).
Key in the password for the selected group. (If no password is set, go to step 3.)
1) Key in the password.
2) Press [OK].
2
Change the data following step 3 on
3
4
Press the [FUNCTION CLEAR] button on the control panel.
The menu returns to the BASIC menu.
150 Changing Data
Download from Www.Somanuals.com. All Manuals Search And Download.
6 TEMPLATES
6.TEMPLATES
„ Changing template data
In the template menu, select the group to which the desired template is registered.
1
1) Press the [REGISTRATION] tab.
2) Press the button for the desired group.
3) Press [OPEN].
To switch the menu
y Press
or
.
y Key in the group number (3 digits).
Enter the password as follows and then press [OK].
2
When the public template group is selected: Press [PASSWORD] and then enter the Admin Password (6 to 10
digits) with the buttons on the touch panel or the digital keys on the control panel.
When a private group is selected: Key in a 5-digit password set for the selected group. If no password is set, go
to step 3.
When you enter the wrong Admin Password 3 times consecutively, this equipment will be locked for 30
seconds. In this case, wait until it is unlocked and then enter the correct password.
Changing Data 151
Download from Www.Somanuals.com. All Manuals Search And Download.
6 TEMPLATES
Select the desired template.
1) Press the button for the corresponding template.
2) Press [EDIT].
3
To switch the menu
Press
or
.
Key in the password for the selected template. (If no password is set, go to step 5.)
1) Key in the password.
2) Press [OK].
4
Change the data following step 7 on
5
152 Changing Data
Download from Www.Somanuals.com. All Manuals Search And Download.
6 TEMPLATES
Deleting Groups or Templates
You can delete private groups or templates no longer needed. If a private group is deleted, all the templates in the private
group are also deleted.
The public template group cannot be deleted.
„ Deleting private groups
In the template menu, select the desired private group.
1) Press the [REGISTRATION] tab.
2) Press the button for the desired group.
3) Press [DELETE].
1
To switch the menu
y Press
or
.
y Key in the group number (3 digits).
Key in the password for the selected group. (If no password is set, go to step 3.)
1) Key in the password.
2) Press [OK].
2
Deleting Groups or Templates 153
Download from Www.Somanuals.com. All Manuals Search And Download.
6 TEMPLATES
Press [DELETE].
3
The private group is now deleted.
154 Deleting Groups or Templates
Download from Www.Somanuals.com. All Manuals Search And Download.
6 TEMPLATES
6.TEMPLATES
„ Deleting templates
In the template menu, select the group to which the desired template is registered.
1
1) Press the [REGISTRATION] tab.
2) Press the button for the desired group.
3) Press [OPEN].
To switch the menu
y Press
or
.
y Key in the group number (3 digits).
Enter the password as follows and then press [OK].
2
When the public template group is selected: Press [PASSWORD] and then enter the Admin Password (6 to 10
digits) with the buttons on the touch panel or the digital keys on the control panel.
When a private group is selected: Key in a 5-digit password set for the selected group. If no password is set, go
to step 3.
When you enter the wrong Admin Password 3 times consecutively, this equipment will be locked for 30
seconds. In this case, wait until it is unlocked and then enter the correct password.
Deleting Groups or Templates 155
Download from Www.Somanuals.com. All Manuals Search And Download.
6 TEMPLATES
Select the desired template.
1) Press the button for the desired template.
2) Press [DELETE].
3
To switch the menu
y Press
or
.
y Key in the group number (3 digits).
Key in the password for the selected template. (If no password is set, go to step 5.)
1) Key in the password.
2) Press [OK].
4
Press [DELETE].
5
The template is now deleted.
156 Deleting Groups or Templates
Download from Www.Somanuals.com. All Manuals Search And Download.
7.
CONFIRMING JOB STATUS
This chapter describes how to confirm the processing status and the history of copy jobs performed.
Confirming Copy Job Status............................................................................................... 158
Confirming copy job history................................................................................................................................162
Download from Www.Somanuals.com. All Manuals Search And Download.
7 CONFIRMING JOB STATUS
Confirming Copy Job Status
You can confirm jobs in progress or ones in waiting, on the touch panel. Also you can delete, pause or resume jobs in
waiting, and change their order. You can also confirm the history of copy jobs performed and the status of the drawers.
„ Confirming jobs in progress or ones in waiting
You can confirm the jobs in progress or the ones in waiting, on the touch panel.
To view them, press [JOB STATUS] on the touch panel.
If this equipment is managed under the user management function, you need to enter user information, such as a user
name or a password in the user authentication menu.
The print job list appears. (Press the [JOBS] tab if another tab menu is displayed.) Copy jobs appear on the print job list as
well as print jobs.
On the print job list, you can confirm the name of the user who sent the job, the date and time the job was sent, the paper
size, the number of pages and copy sets and the processing status. 5 jobs appear on 1 page of the print job list. When you
press
or
on the touch panel, the menu will be changed to the previous one or the next one, so that you can view
up to 1000 jobs.
Press [CLOSE] when you finish the confirmation. The menu returns to the one shown before you pressed [JOB STATUS].
158 Confirming Copy Job Status
Download from Www.Somanuals.com. All Manuals Search And Download.
7 CONFIRMING JOB STATUS
7.CONFIRMING JOB STATUS
‰ Deleting jobs
You can delete jobs that you no longer need to print.
Select the desired job on the print job list, and then press [DELETE].
1
Press [DELETE].
2
The job is now deleted.
Confirming Copy Job Status 159
Download from Www.Somanuals.com. All Manuals Search And Download.
7 CONFIRMING JOB STATUS
‰ Pausing jobs
You can pause jobs in waiting.
Only the 11th and later jobs (counted from the job in progress) can be paused.
Select the desired job on the print job list, and then press [PAUSE].
The job is now paused. The paused job is not printed even when its turn comes. Printing of the next job starts.
Resuming the paused job
Select the desired job, and then press [RESUME].
160 Confirming Copy Job Status
Download from Www.Somanuals.com. All Manuals Search And Download.
7 CONFIRMING JOB STATUS
7.CONFIRMING JOB STATUS
‰ Moving jobs
You can change the order of the jobs in waiting by moving them within the list.
Only the 11th and later jobs (counted from the job in progress) can be moved. They can be moved to 11th and later.
Select the desired job on the print job list, and then press [MOVE].
1
Select the position that you want the job to move to. (It will come under the selected
job.)
2
Confirming Copy Job Status 161
Download from Www.Somanuals.com. All Manuals Search And Download.
7 CONFIRMING JOB STATUS
„ Confirming copy job history
You can confirm the history of copy jobs performed on the touch panel.
Press [JOB STATUS] on the touch panel.
1
Press the [LOG] tab.
2
Press [PRINT].
3
The print log list appears. Copy jobs appear on the print log list as well as print jobs.
On the print log list, you can confirm the name of the user who performed the job, the date and time the job was
printed, the paper size and the number of pages or copy sets. 5 jobs appear on 1 page of the print log list. When
you press
or
on the touch panel, the menu will be changed to the previous one or the next one, so that you
can view up to 120 jobs.
When you finish the confirmation, press [RETURN] so that the menu returns to the one in step 3, and then press
[CLOSE]. The menu returns to the one shown before you pressed [JOB STATUS].
162 Confirming Copy Job Status
Download from Www.Somanuals.com. All Manuals Search And Download.
7 CONFIRMING JOB STATUS
7.CONFIRMING JOB STATUS
„ Confirming drawers
You can confirm the size and type-setting of the paper or the amount remaining in the drawers. During printing you can
confirm which drawer is feeding paper.
Press [JOB STATUS] on the touch panel.
1
Press the [SUPPLY] tab.
2
During printing, the button for the drawer from which the paper is fed is highlighted.
Press [CLOSE] when you finish the confirmation. The menu returns to the one shown before you pressed [JOB
STATUS].
When the paper in the drawer has run out during printing, [JOB STATUS] on the touch panel blinks. In this case, press
[JOB STATUS] so that the menu for displaying the printing status will appear and the button for the drawer whose paper
has run out will blink on this menu. Printing resumes when you add paper to this drawer.
Confirming Copy Job Status 163
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
8 OTHER INFORMATION
Continuous Copying Speed
Copy speeds under the condition in which originals are placed on the original glass and single-side copies are made
continuously with 100% reproduction ratio in the non-sort mode (unit: sheet/minute).
e-STUDIO555
Paper type
PLAIN
THICK1
THICK2
THICK3
Paper size
Feeder
Face
Face
Face
Face
Face
Face
Face
Face
up
55
55
45
44
37
38
32
34
28
down
up
55
55
45
44
37
38
32
34
28
down
up
55
55
45
44
37
38
32
34
28
down
up
52
52
45
42
37
37
32
33
28
down
A4, A5-R, B5, LT,
ST-R, 8.5"SQ
Drawer
55
55
45
44
37
38
32
32
28
55
55
45
44
37
38
32
32
28
55
55
45
44
37
38
32
32
28
52
52
45
42
37
37
32
31
28
Tandem LCF *1
Bypass tray
Drawer
A4-R, B5-R, LT-R
Bypass tray
Drawer
B4, FOLIO, LG,
COMP, 13"LG
Bypass tray
Drawer
A3, LD
Bypass tray
e-STUDIO655
Paper type
PLAIN
THICK1
THICK2
THICK3
Paper size
Feeder
Face
up
Face
down
Face
up
Face
down
Face
up
Face
down
Face
up
Face
down
A4, A5-R, B5, LT,
ST-R, 8.5"SQ
Drawer
65
65
46
48
38
42
34
37
30
65
65
46
48
38
40
34
33
30
65
65
46
48
38
42
34
37
30
65
65
46
48
38
40
34
33
30
65
65
46
48
38
42
34
37
30
65
65
46
48
38
40
34
33
30
60
60
46
46
38
41
34
36
30
60
60
46
46
38
38
34
32
30
Tandem LCF *1
Bypass tray
Drawer
A4-R, B5-R, LT-R
Bypass tray
Drawer
B4, FOLIO, LG,
COMP, 13"LG
Bypass tray
Drawer
A3, LD
Bypass tray
e-STUDIO755
Paper type
PLAIN
THICK1
THICK2
THICK3
Paper size
Feeder
Face
up
Face
down
Face
up
Face
down
Face
up
Face
down
Face
up
Face
down
A4, A5-R, B5, LT,
ST-R, 8.5"SQ
Drawer
75
75
46
55
38
47
34
40
30
75
75
46
52
38
43
34
35
30
75
75
46
55
38
47
34
40
30
75
75
46
52
38
43
34
35
30
75
75
46
55
38
47
34
40
30
75
75
46
52
38
43
34
35
30
65
65
46
50
38
43
34
37
30
65
65
46
48
38
40
34
34
30
Tandem LCF *1
Bypass tray
Drawer
A4-R, B5-R, LT-R
Bypass tray
Drawer
B4, FOLIO, LG,
COMP, 13"LG
Bypass tray
Drawer
A3, LD
Bypass tray
166 Continuous Copying Speed
Download from Www.Somanuals.com. All Manuals Search And Download.
8 OTHER INFORMATION
8.OTHER INFORMATION
e-STUDIO855
Paper size
Paper type
PLAIN
THICK1
THICK2
THICK3
Feeder
Face
Face
Face Face
Face
Face
down
Face
up
Face
down
up
85
85
50
61
42
52
38
43
34
down
up
85
85
50
61
42
52
38
43
34
down
85
up
85
85
50
61
42
52
38
43
34
A4, A5-R, B5, LT,
ST-R, 8.5"SQ
Drawer
85
85
50
56
42
45
38
37
34
85
85
50
56
42
45
38
37
34
72
72
46
52
38
44
34
37
30
72
72
46
50
38
41
34
34
30
Tandem LCF *1
Bypass tray
Drawer
85
50
A4-R, B5-R, LT-R
56
Bypass tray
Drawer
42
B4, FOLIO, LG,
COMP, 13"LG
45
Bypass tray
Drawer
38
A3, LD
37
Bypass tray
34
*1 Only A4 and LT-sized paper can be set in the tandem large capacity feeder (Tandem LCF).
y “Face up” and “Face down” in the table mean how the paper exits.
y The bypass copying speed when the paper size is specified is as listed above.
y TOSHIBA-recommended paper is used for the values of the specifications above.
y These specifications vary depending on the copying conditions and the environment.
Continuous Copying Speed 167
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
Duplex copying
Numerics
A
E
negative/positive reversal ...................................... 102
BOOK - TABLET .................................................. 118
BOOK CENTER ERASE ......................................... 90
B
BOOK CENTER ERASE .............................................90
Bypass copying
bypass copying .......................................................36
standard size paper .................................................37
C
Clearing the set functions ............................................47
Copying
bypass copying .......................................................36
continuous copying speed ......................................166
mixed-size originals .................................................50
Copying functions
F
Finisher
Saddle Stitch Finisher ............................................. 60
Finishing mode
confirming the set functions ......................................46
D
Default settings ..........................................................46
INDEX 171
Download from Www.Somanuals.com. All Manuals Search And Download.
Original mode
Originals
acceptable originals ................................................ 22
mixed-size originals ................................................ 50
G
H
Hole Punch Unit .........................................................60
I
Image adjustment functions
image adjustment functions ....................................133
INSERTER
FRONT & BACK COVER .......................................130
Interrupting copying ....................................................32
P
Paper
acceptable copy paper ............................................ 11
Private group
J
Jobs
pausing / resuming ................................................160
K
R
RADF (Reversing Automatic Document Feeder)
Reversing Automatic Document Feeder (RADF)
L
M
N
S
O
172 INDEX
Download from Www.Somanuals.com. All Manuals Search And Download.
Side guides of the RADF
Simplex/duplex setting ................................................46
[START] button ..........................................................29
T
TAB PAPER
COPIED TAB INSERT ...........................................121
Templates
U
[USER FUNCTIONS] button ........................................17
X
Z
INDEX 173
Download from Www.Somanuals.com. All Manuals Search And Download.
174 INDEX
Download from Www.Somanuals.com. All Manuals Search And Download.
DP-5550/6550/7550/8550
OME080171A0
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTIFUNCTIONAL DIGITAL SYSTEMS
Copying Guide
2-17-2, HIGASHIGOTANDA, SHINAGAWA-KU, TOKYO, 141-8664, JAPAN
R081120G8001-TTEC
Ver01 2009-12
©2009 TOSHIBA TEC CORPORATION All rights reserved
Download from Www.Somanuals.com. All Manuals Search And Download.
|
