Q u i c k i e 2 L i t e
Quickie® 2 Lite
O w n e r ’ s M a n u a l
Supplier:
This manual must be given to the rider of this wheelchair.
Rider:
Before using this wheelchair read this entire manual and save for future reference.
Improving People’s Lives
Download from Www.Somanuals.com. All Manuals Search And Download.
II. TABLE OF CONTENTS
I. INTRODUCTION .................................................
II. TABLE OF CONTENTS.........................................
III. YOUR CHAIR AND ITS PARTS............................
IV. NOTICE - READ BEFORE USE .............................
V. GENERAL WARNINGS..........................................
A.Weight Limit .............................................................
B. Weight Training .........................................................
C.Getting to Know Your Chair ....................................
D.To Reduce The Risk of an Accident ..........................
E. Safety Checklist ........................................................
F. Changes & Adjustments ...........................................
G.Environmental Conditions ........................................
H.Terrain ......................................................................
I. Street Use .................................................................
J. Motor Vehicle Safety ................................................
K.When You Need Help ..............................................
VI. WARNINGS: FALLS & TIP-OVERS.......................
A.Center of Balance .....................................................
B. Dressing or Changing Clothes ..................................
C.Wheelies ...................................................................
D.Obstacles ..................................................................
E. Reaching or Leaning ..................................................
F. Moving Backward .....................................................
G.Ramps, Slopes & Sidehills .........................................
H.Transfers ...................................................................
I. Curbs & Steps............................................................
J. Stairs .........................................................................
K.Escalators ..................................................................
VII. WARNINGS: FOR SAFE USE................................
A.Learning To Do A “Wheelie” ....................................
B. Descending A Curb or Single Step ...........................
C.Climbing A Curb or Single Step ...............................
D.Climbing Stairs ..........................................................
E. Descending Stairs ......................................................
F. Maintenance .............................................................
2
3
4
5
5
5
5
5
5
5
6
6
6
6
6
6
7
7
7
7
7
7
8
8
8
8
8
8
9
9
9
9
9
9
9
E. Fasteners .................................................................. 10
F. Footrests.................................................................... 10
G.Pneumatic Tires ........................................................ 10
H.Transit Use................................................................. 11
I. Transit Option............................................................ 11
J. Positioning Belts......................................................... 11
K.Push Handles ............................................................. 11
L. Quick-Release Axles ................................................. 11
M.Rear Wheels ............................................................. 11
N.Rear Wheel Locks .................................................... 11
O.Modified Seat Systems .............................................. 12
P. Upholstery Fabric ..................................................... 12
IX. SET-UP, ADJUSTMENT AND USE........................ 13
A.To Mount and Remove Rear Wheels......................... 13
B. Rear Wheel Axle Nut Adjustment............................. 13
C.Padded, Swing-Away Armrests.................................. 13
D.Height Adjustable Armrests ...................................... 14
E. Swing-In/Out Hangers and Footrests........................ 14
F. Fixed Front Footrest Height Adjustment.................. 14
G.Angle Adjustable Footplates ...................................... 15
H.Backrest .................................................................... 15
I. Angle Adjustable Backrest......................................... 15
J. Seat Sling.................................................................... 16
K.Cushion Installation ................................................... 16
L. Rear Axles.................................................................. 16
M.Wheel Locks.............................................................. 17
N.Casters....................................................................... 17
O. Anti-Tip Tubes (Optional)......................................... 18
P. Plastic Side Guards .................................................... 19
Q.Folding and Unfolding................................................ 19
R. Check-Out................................................................. 19
X. TROUBLESHOOTING........................................... 20
XI. MAINTENANCE ................................................... 21
A.Introduction............................................................... 21
B. Maintenance Chart ................................................... 21
C.Maintenance Tips....................................................... 21
D.Cleaning..................................................................... 21
E. Storage Tips............................................................... 21
XII. SUNRISE LIMITED WARRANTY.......................... 22
VIII. WARNINGS: COMPONENTS & OPTIONS ......... 10
A.Anti-Tip Tubes (Optional).......................................... 10
B. Armrests ................................................................... 10
C.Caster Pin Locks........................................................ 10
D.Cushion & Sling Seats ............................................... 10
108590 Rev. A
3
Download from Www.Somanuals.com. All Manuals Search And Download.
III. YOUR CHAIR AND ITS PARTS
2
19
1
3
12
4
14
5
18
6
13
9
8
10
11
7
15
16
17
20
QUICKIE 2 LITE– SWING-AWAY FOOTREST
1. Backrest Tube
2. Backrest
3. Pneumatic Tire
FIXED FRONT
4. Aluminum Handrim
5. Aluminum Wheel Rim
6. Spokes
7. Rear Wheel Hub
8. Quick-Release Axle
9. Swing-Away Latch Release
10. Caster Housing Cap
11. Caster Housing
12. Seat Sling
13. X-Hinge (not shown– under seat)
14. Swing-In / Swing-Out Legrest
15. Caster Fork
16. Caster Tire
17. Flip-Up Footrest with Heel Loops
18. Anti-tip tube
19. Padded Swing-Away Armrest
20. Fixed Front
108590 Rev. A
4
Download from Www.Somanuals.com. All Manuals Search And Download.
IV. NOTICE– READ BEFORE USE
A. CHOOSE THE RIGHT CHAIR & SAFETY
OPTIONS
Sunrise provides a choice of many wheelchair styles to meet the needs of
the wheelchair rider. However, final selection of the type of wheelchair,
options and adjustments rests solely with you and your health care advisor.
Choosing the best chair and set-up for your safety depends on such things
as:
C. WARNINGS
The word “WARNING” refers to a hazard or unsafe practice that may cause
severe injury or death to you or to other persons. The “Warnings” are in four
main sections, as follows:
1. V — GENERAL WARNINGS
Here you will find a safety checklist and a summary of risks you need
to be aware of before you ride this chair.
1. Your disability, strength, balance and coordination.
2. The types of hazards you must overcome in daily use (where you
live and work, and other places you are likely to use your chair).
3. The need for options for your safety and comfort (such as anti-tip
tubes, positioning belts, or special seating systems).
2. VI — WARNINGS — FALLS & TIP-OVERS
Here you will learn how to avoid a fall or tip-over while you perform
daily activities in your chair.
3. VII — WARNINGS — FOR SAFE USE
B. REVIEW THIS MANUAL OFTEN
Here you will learn about practices for the safe use of your chair
Before using this chair you, and each person who may assist you, should
read this entire manual and make sure to follow all instructions. Review the
warnings often, until they are second nature to you.
4. VIII — WARNINGS — COMPONENTS & OPTIONS
Here you will learn about the components of your chair and options
you can select for safety. Consult your authorized supplier and your
health care advisor to help you choose the best set-up and options
for safe use.
NOTE– Where they apply, you will also find “Warnings” in other sections of
this manual. Heed all warnings in this section. If you fail to do so a
fall, tip-over or loss of control may occur and cause severe injury to
the rider or others.
V. GENERAL WARNINGS
A. WEIGHT LIMIT
D. TO REDUCE THE RISK OF AN ACCIDENT
WARNING
WARNING
1. BEFORE riding, you should be trained in the safe use of this chair by
your health care advisor.
NEVER exceed the weight limit of 265 pounds (120 kg) for the Quickie 2 Lite
for combined weight of rider and items carried. If you do exceed the limit,
damage to your chair, a fall, tip-over or loss of control may occur and cause
severe injury to the rider or others.
2. Practice bending, reaching and transfers until you know the limit of
your ability. Have someone help you until you know what can cause
a fall or tip-over and how to avoid doing so.
3. Be aware that you must develop your own methods for safe use best
suited to your level of function and ability.
B. WEIGHT TRAINING
4. NEVER try a new maneuver on your own until you are sure you can
do it safely.
5. Get to know the areas where you plan to use your chair. Look for
hazards and learn how to avoid them.
6. Use anti-tip tubes unless you are a skilled rider of this chair and are
sure you are not at risk to tip over.
WARNING
NEVER use this chair for weight training if total weight (rider plus equip-
ment) exceeds 265 pounds(120 kg) for Quickie 2 Lite. If you do exceed the
limit, damage to your chair, a fall, tip-over or loss of control may occur and
cause severe injury to the rider or others.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
C. GETTING TO KNOW YOUR CHAIR
WARNING
E. SAFETY CHECKLIST
WARNING
Before Each Use Of Your Chair:
1. Make sure the chair rolls easily and that all parts work smoothly.
Check for noise, vibration, or a change in ease of use. (This may indi-
cate low tire pressure, loose fasteners, or damage to your chair).
2. Immediately repair any problem. Your authorized supplier can help
you find and correct the problem.
Every wheelchair is different. Take the time to learn the feel of this chair
before you begin riding. Start slowly, with easy, smooth strokes. If you are
used to a different chair, you may use too much force and tip over. If you
use too much force, damage to your chair, a fall, tip-over or loss of control
may occur and cause severe injury to the rider or others.
3. Check to see that both quick-release rear axles are locked. When
locked, the axle button will “pop out” fully. If not locked, the wheel
may come off and cause you to fall.
108590 Rev. A
5
Download from Www.Somanuals.com. All Manuals Search And Download.
V.
4. If your chair has anti-tip tubes, lock them in place.
NOTE– See “Anti-Tip Tubes” (Section VIII) for times you should not use them.
J. MOTOR VEHICLE SAFETY
Identify whether your chair has been manufactured with the Transit Option
installed.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
WARNING
If your chair is NOT equipped with the Transit Option:
1. NEVER let anyone sit in this chair while in a moving vehicle.
a. ALWAYS move the rider to an approved vehicle seat.
b. ALWAYS secure the rider with proper motor vehicle restraints.
2. In an accident or sudden stop the rider may be thrown from the
chair. Wheelchair seat belts will not prevent this, and further injury
may result from the belts or straps.
3. NEVER transport this chair in the front seat of a vehicle. It may shift
and interfere with the driver.
4. ALWAYS secure this chair so that it cannot roll or shift.
5. Do not use any chair that has been involved in a motor vehicle acci-
dent.
F. CHANGES & ADJUSTMENTS
WARNING
1. If you modify or adjust this chair, it may increase the risk of a tip-
over.
2. Consult your authorized supplier BEFORE you modify or adjust your
chair.
3. We recommend that you use anti-tip tubes until you adapt to the
change and are sure you are not at risk to tip over.
4. Unauthorized modifications or use of parts not supplied or approved
by Sunrise may change the chair structure. This will void the warran-
ty and may cause a safety hazard.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
If your chair is equipped with the Transit Option: See section VIII. Warnings:
Components and Options, Parts H. Transit Use and I. Transit Option.
G. ENVIRONMENTAL CONDITIONS
WARNING
K. WHEN YOU NEED HELP
1. Use extra care if you must ride your chair on a wet or slick surface.
If you are in doubt, ask for help.
WARNING
2. Contact with water or excess moisture may cause your chair to rust
or corrode. This could cause your chair to fail.
For The Rider:
Make sure that each person who helps you reads and follows all warnings
and instructions that apply.
a. Do not use your chair in a shower, pool or other body of water.
The chair tubing and parts are not water-tight and may rust or
corrode from the inside.
b. Avoid excess moisture (for example, do not leave your chair in a
damp bathroom while taking a shower).
For Attendants:
1. Work with the rider’s doctor, nurse or therapist to learn safe meth-
ods best suited to your abilities and those of the rider.
2. Tell the rider what you plan to do, and explain what you expect the
rider to do. This will put the rider at ease and reduce the risk of an
accident.
c. Dry your chair as soon as you can if it gets wet, or if you use water
to clean it.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
3. Make sure the chair has push handles. They provide secure points
for you to hold the rear of the chair to prevent a fall or tip-over.
Check to make sure push handle grips will not rotate or slip off.
4. To prevent injury to your back, use good posture and proper body
mechanics. When you lift or support the rider or tilt the chair, bend
your knees slightly and keep your back as upright and straight as you
can.
5. Remind the rider to lean back when you tilt the chair backward.
6. When you descend a curb or single step, slowly lower the chair in
one easy movement. Do not let the chair drop the last few inches to
the ground. This may damage the chair or injure the rider.
7. To avoid tripping, unlock and rotate anti-tip tubes up, out of the way.
8. ALWAYS lock the rear wheels and lock anti-tip tubes in place if you
must leave the rider alone, even for a moment. This will reduce the
risk of a tip-over or loss of control of the chair.
H. TERRAIN
WARNING
1. Your chair is designed for use on firm, even surfaces such as con-
crete,asphalt and indoor floors and carpeting.
2. Do not operate your chair in sand, loose soil or over rough terrain.
This may damage wheels or axles or loosen fasteners of your chair.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
I. STREET USE
WARNING
In most states, wheelchairs are not legal for use on public roads. Be alert to
the danger of motor vehicles on roads or in parking lots.
1. At night, or when lighting is poor, use reflective tape on your chair
and clothing.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
2. Due to your low position, it may be hard for drivers to see you.
Make eye contact with drivers before you go forward. When in
doubt, yield until you are sure it is safe.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
108590 Rev. A
6
Download from Www.Somanuals.com. All Manuals Search And Download.
VI. WARNINGS: FALLS & TIP-OVERS
A. CENTER OF BALANCE
D. OBSTACLES
WARNING
WARNING
Obstacles and road hazards (such as potholes and broken pavement) can
damage your chair and may cause a fall, tip-over or loss of control.
To avoid these risks:
1. Keep a lookout for danger – scan the area well ahead of your chair
as you ride.
2. Make sure the floor areas where you live and work are level and free
of obstacles.
3. Remove or cover threshold strips between rooms.
4. Install a ramp at entry or exit doors. Make sure there is not a drop
off at the bottom of the ramp.
5. To Help Correct Your Center Of Balance:
a. Lean your upper body FORWARD slightly as you go UP over an
obstacle.
b. Press your upper body BACKWARD as you go DOWN from a
higher to a lower level.
6. If your chair has anti-tip tubes, lock them in place before you go UP
over an obstacle.
The point where this chair will tip forward, back or to the side depends on
its center of balance and stability. How your chair is set up, the options you
select and the changes you make may affect the risk of a fall or tip-over.
1. The Most Important Adjustment Is:
The position of the rear wheels. The more you move the rear
wheels forward, the more likely your chair will tip over backward.
2. The Center Of Balance Is Also Affected By:
a. A change in the set-up of your chair, including:
• The distance between the rear wheels.
• The amount of rear wheel camber.
• The seat height and seat angle.
• Backrest angle.
b. A change in your body position, posture or weight distribution.
c. Riding your chair on a ramp or slope.
d. The use of a back pack or other options and the amount of
added weight.
3. To Reduce The Risk Of An Accident:
a. Consult your doctor, nurse or therapist to find out what axle and
caster position is best for you.
b. Consult your authorized supplier BEFORE you modify or adjust
this chair. Be aware that you may need to make other changes to
correct the center of balance.
7. Keep both of your hands on the handrims as you go over an obstacle.
8. Never push or pull on an object (such as furniture or a doorjamb) to
propel your chair.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
c. Have someone help you until you know the balance points of
your chair and how to avoid a tip-over.
d. Use anti-tip tubes.
E. REACHING OR LEANING
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
WARNING
If you reach or lean it will affect the center of balance of your chair. This
may cause you to fall or tip over. When in doubt, ask for help or use a
device to extend your reach.
1. NEVER reach or lean if you must shift your weight sideways or rise up
off the seat.
2. NEVER reach or lean if you must move forward in your seat to do
so. Always keep your buttocks in contact with the backrest.
3. NEVER reach with both hands (you may not be able to catch your-
self to prevent a fall if the chair tips).
4. NEVER reach or lean to the rear unless your chair has anti-tip tubes
locked in place.
B. DRESSING OR CHANGING CLOTHES
WARNING
Your weight may shift if you dress or change clothes while seated in this
chair.
To reduce the risk of a fall or tip-over:
1. Rotate the front casters until they are as far forward as possible.
This makes the chair more stable.
2. Lock anti-tip tubes in place. (If your chair does not have anti-tip
tubes, back it up against a wall and lock both rear wheels).
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
5. DO NOT reach or lean over the top of the seat back. This may
damage one or both backrest tubes and cause you to fall.
6. If You Must Reach Or Lean:
a. Do not lock the rear wheels. This creates a tip point and makes
a fall or tip-over more likely.
b. Do not put pressure on the footrests.
C. WHEELIES
WARNING
Doing a “wheelie” means: balancing on the rear wheels of your chair, while
the front casters are in the air. It is dangerous to do a “wheelie” as a fall or
tip-over may occur. However, if you do it safely, a “wheelie” can help you
overcome curbs and obstacles.
1. Consult your doctor, nurse or therapist to find out if you are a good
candidate to learn to do a “wheelie.”
2. Do not attempt a “wheelie” UNLESS you are a skilled rider of this
chair, or you have help.
NOTE– See steps to learn to do a “wheelie.”
NOTE– Leaning forward puts pressure on the footrests and may cause the
chair to tip if you lean too far.
c. Move your chair as close as you can to the object you wish to
reach.
d. Do not try to pick up an object from the floor by reaching down
between your knees. You are less likely to tip if you reach to the
side of your chair.
e. Rotate the front casters until they are as far forward as possible.
This makes the chair more stable.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
NOTE– To do this: Move your chair past the object you want to reach, then
back up alongside it. Backing up will rotate the casters forward.
f. Firmly grasp a rear wheel or an armrest with one hand. This will
help to prevent a fall if the chair tips.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
108590 Rev. A
7
Download from Www.Somanuals.com. All Manuals Search And Download.
VI.
b. Have someone help you until you know how to do a safe transfer
on your own.
2. Lock the rear wheels before you transfer. This keeps the rear wheels
from rolling.
NOTE– This will NOT keep your chair from sliding away from you
or tipping.
3. Make sure to keep pneumatic tires properly inflated. Low tire pres-
sure may allow the rear wheel locks to slip.
4. Move your chair as close as you can to the seat you are transferring
to.
F. MOVING BACKWARD
WARNING
Use extra care when you move your chair backward. Your chair is most sta-
ble when you propel yourself forward. You may lose control or tip over if
one of the rear wheels hits an object and stops rolling.
1. Propel your chair slowly and smoothly.
2. If your chair has anti-tip tubes, make sure to lock them in place.
3. Stop often and check to be sure your path is clear.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
If possible, use a transfer board.
5. Rotate the front casters until they are as far forward as possible.
6. If you can, remove or swing footrests out of the way.
a. Make sure your feet do not catch in the space between the
footrests.
b. Avoid putting weight on the footrests as this may cause the chair
to tip.
7. Make sure armrests are out of the way and do not interfere.
8. Transfer as far back onto the seat surface as you can. This will reduce
the risk that the chair will tip or move away from you.
G. RAMPS, SLOPES & SIDEHILLS
WARNING
Riding on a slope, which includes a ramp or sidehill, will change the center
of balance of your chair. Your chair is less stable when it is at an angle. Anti-
tip tubes may not prevent a fall or tip-over.
1. Do not use your chair on a slope steeper than 10%. (A 10% slope
means: one foot in elevation for every ten feet of slope length.)
2. Always go as straight up and as straight down as you can. (Do not
“cut the corner” on a slope or ramp.)
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
3. Do not turn or change direction on a slope.
I. CURBS & STEPS
4. Always stay in the CENTER of the ramp. Make sure ramp is wide
enough that you are not at risk that a wheel may fall over the edge.
5. Do not stop on a steep slope. If you stop, you may lose control of
your chair.
6. NEVER use rear wheel locks to try to slow or stop your chair. This is
likely to cause your chair to veer out of control.
WARNING
1. Each person who helps you should read and follow the warnings
“For Safe Use” (Section VII).
2. Do not try to climb or descend a curb or step alone UNLESS you
are a skilled rider of this chair and:
7. Beware Of:
a. You can safely do a “wheelie”; and
a. Wet or slippery surfaces.
b. A change in grade on a slope (or a lip, bump or depression).
These may cause a fall or tip-over.
b. You are sure you have the strength and balance to do so.
3. Unlock and rotate anti-tip tubes up, out of the way, so they do not
interfere.
4. Do not try to climb a high curb or step (more than 4 inches high)
UNLESS you have help. Doing so may cause your chair to exceed its
balance point and tip over.
5. Go straight up and straight down a curb or step. If you climb or
descend at an angle, a fall or tip-over is likely.
6. Be aware that the impact of dropping down from a curb or step can
damage your chair or loosen fasteners.
c. A drop-off at the bottom of a slope. A drop-off as small as 3/4
inch can stop a front caster and cause the chair to tip forward.
8. To Reduce The Risk Of A Fall Or Tip-Over:
a. Lean or press your body UPHILL. This will help adjust for the
change in the center of balance caused by the slope or sidehill.
b. Keep pressure on the handrims to control your speed on a
down slope. If you go too fast you may lose control.
c. Ask for help any time you are in doubt.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
9. Ramps At Home & Work– For your safety, ramps at home and work
must meet all legal requirements for your area. We recommend:
a. Width. At least four feet wide.
J. STAIRS
b. Guardrails. To reduce the risk of a fall, sides of ramp must have
guardrails (or raised borders at least three inches high).
c. Slope. Not more than a 10% grade.
WARNING
1. NEVER use this chair on stairs UNLESS you have someone to help
you. Doing so is likely to cause a fall or tip-over.
d. Surface. Flat and even, with a thin carpet or other non-skid
material. (Make sure there is no lip, bump or depression.)
e. Bracing. Ramp must be STURDY. You may need bracing so ramp
does not “bow” when you ride on it.
2. Persons who help you should read and follow the warnings “For
Attendants” (Section V., Part K) and “For Safe Use” (Section VII).
f. Avoid A Drop Off. You may need a section at the top or bottom
to smooth out the transition.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
K. ESCALATORS
WARNING
H. TRANSFER
NEVER use this chair on an escalator, even with an attendant. If you do, a
fall or tip-over is likely.
WARNING
It is dangerous to transfer on your own. It requires good balance and agility.
Be aware that there is a point during every transfer when the wheelchair
seat is not below you. To avoid a fall:
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
1. Work with your health care advisor to learn safe methods.
a. Learn how to position your body and how to support yourself
during a transfer.
108590 Rev. A
8
Download from Www.Somanuals.com. All Manuals Search And Download.
VII. WARNINGS: FOR SAFE USE
D. CLIMBING STAIRS
WARNING
WARNING
Before you assist a rider, be sure to read the warnings “For
Attendants” and follow all instructions that apply. Be aware
that you will need to learn safe methods best suited to your
abilities.
1. Use at least two attendants to move a chair and rider up stairs.
2. Move the chair and rider BACKWARD up the stairs.
3. The person at the rear is in control. He or she tilts the chair back to
its balance point.
4. A second attendant at the front firmly grasps a non-detachable part
of the front frame and lifts the chair up and over one stair at a time.
5. The attendants move to the next stair up. Repeat for each stair, until
you reach the landing.
A. LEARNING TO DO A “WHEELIE”
WARNING
Follow these steps to help the rider learn to do a “wheelie”:
1. Read and follow the warnings for “WHEELIES.”
2. Stand at the rear of the chair. You must be able to move with the
chair to prevent a tip-over.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
3. Keep your hands BENEATH the push handles, ready to catch the
rider if the chair tips back.
4. When you are ready, have the rider place his or her hands on the
forward part of the handrims.
5. Have the rider make a quick BACKWARD movement of the rear
wheels, quickly followed by a hard FORWARD thrust. (This will tilt
the chair up on the balance point of the rear wheels.)
6. Have the rider make small movements of the handrims to stay in bal-
ance.
E. DESCENDING STAIRS
WARNING
1. Use at least two attendants to move a chair and rider down stairs.
2. Move the chair and rider FORWARD down the stairs.
3. The person at the rear is in control. He or she tilts the chair to the
balance point of the rear wheels and rolls it to the edge of the top
step.
4. A second attendant stands on the third step from the top and grasps
the chair frame. He or she lowers the chair one step at a time by let-
ting the rear wheels roll over the stair edge.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
5. The attendants move to the next stair down. Repeat for each stair,
until you reach the landing.
B. DESCENDING A CURB OR SINGLE STEP
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
WARNING
Follow these steps to help a rider descend a curb or single step going
BACKWARD:
F. MAINTENANCE
1. Stay at the rear of the chair.
2. Several feet before your reach the edge of the curb or step, turn the
chair around and pull it backward.
WARNING
1. Inspect and maintain this chair strictly per Maintenance Chart in
Section XII.
3. While looking over your shoulder, carefully step back until you are
off the curb or stair and standing on the lower level.
4. Pull the chair toward you until the rear wheels reach the edge of the
curb or step. Then allow the rear wheels to slowly roll down onto
the lower level.
5. When the rear wheels are safely on the lower level, tilt the chair
back to its balance point. This will lift the front casters off the curb
or step.
2. If you detect a problem, make sure to service or repair the chair
before use.
3. At least once a year, have a complete inspection, safety check and
service of your chair made by an authorized supplier.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury or death to the rider or
others. For additional maintenance information see Section XII:
Maintenance.
6. Keep the chair in balance and take small steps backward. Turn the
chair around and gently lower front casters to the ground.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
C. CLIMBING A CURB OR SINGLE STEP
WARNING
Follow these steps to help the rider climb a curb or single step going
FORWARD:
1. Stay behind the chair.
2. Face the curb and tilt the chair up on the rear wheels so that the
front casters clear the curb or step.
3. Move forward, placing the front casters on the upper level as soon as
you are sure they are past the edge.
4. Continue forward until the rear wheels contact the face of the curb
or step. Lift and roll the rear wheels to the upper level.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
108590 Rev. A
9
Download from Www.Somanuals.com. All Manuals Search And Download.
VIII. WARNINGS: COMPONENTS AND OPTIONS
3. Seat slings are not intended to be used as a direct seating surface. A
cushion or other seating surface should be placed on the sling before
use.
A. ANTI-TIP TUBES (OPTIONAL)
WARNING
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
Anti-tip tubes can help keep your chair from tipping over backward in most
normal conditions.
1. Sunrise Recommends Use Of Anti-Tip Tubes:
a. UNLESS you are a skilled rider of this chair and are sure you are
not at risk to tip over.
E. FASTENERS
WARNING
b. Each time you modify or adjust your chair. The change may
make it easier to tip backward. Use anti-tip tubes until you adapt
to the change and are sure you are not at risk to tip over.
2. When locked in place (in the “down” position) anti-tip tubes should
be BETWEEN 1 1/2 to 2 inches off the ground.
a. If set too HIGH, they may not prevent a tip-over.
b. If set too LOW, they may “hang up” on obstacles you may
encounter in normal use. If this occurs, you may fall or your
chair may tip over.
Many of the screws, bolts and nuts on this chair are special high-strength
fasteners. Use of improper fasteners may cause your chair to fail.
1. ONLY use fasteners provided by an authorized supplier (or ones of
the same type and strength, as indicated by the markings on the
heads).
2. Over- or under-tightened fasteners may fail or cause damage to chair
parts.
3. If bolts or screws become loose, tighten them as soon as you can.
3. Keep Anti-Tip Tubes Locked In Place UNLESS:
a. You have an attendant; or
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
b. You have to climb or descend a curb or overcome an obstacle
and can safely do so without them. At these times, make sure
anti-tip tubes are up, out of the way.
F. FOOTRESTS
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
WARNING
1. At the lowest point, footrests should be AT LEAST 2 inches off the
ground. If set too LOW, they may “hang up” on obstacles you can
expect to find in normal use. This may cause the chair to stop sud-
denly and tip forward.
B. ARMRESTS
WARNING
Armrests detach and will not bear the weight of this chair.
1. NEVER lift this chair by its armrests. They may come loose or break.
2. Lift this chair only by non-detachable parts of the main frame.
2. To Avoid A Trip Or Fall When You Transfer:
a. Make sure your feet do not “hang up” or get caught in the space
between the footrests.
b. Avoid putting weight on the footrests, as the chair may tip forward.
3. NEVER lift this chair by the footrests. Footrests detach and will not
bear the weight of this chair. Lift this chair only by non-detachable
parts of the main frame.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
C. CASTER PIN LOCKS
WARNING
G. PNEUMATIC TIRES
Always use both pin locks when transferring in and out of the chair.
Caster pin locks only keep the front caster wheels from changing direction,
they do not lock-out the front wheels from rotation. To prevent the wheel-
chair from rolling, you must engage the rear wheel locks.
WARNING
Proper inflation extends the life of your tires and makes your chair easier to
use.
If you propel your wheelchair with the caster pin locks engaged, the chair
will be prevented from turning.
1. Do not use this chair if any of the tires are under- or over-inflated.
Check weekly for proper inflation level, as listed on the tire sidewall.
2. Low pressure in a rear tire may cause the wheel lock on that side to
slip and allow the wheel to turn when you do not expect it.
3. Low pressure in any of the tires may cause the chair to veer to one
side and result in a loss of control.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
D. CUSHIONS & SLING SEATS
4. Over-inflated tires may burst.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
WARNING
1. Quickie sling seats and standard foam cushions are not designed for
the relief
of pressure.
2. If you suffer from pressure sores or if you are at risk that they will
occur, you may need a special seat system or a device to control your
posture. Consult your doctor, nurse or therapist to find out if you
need such a device for your well-being.
108590 Rev. A
10
Download from Www.Somanuals.com. All Manuals Search And Download.
VIII.
4. Use positioning belts only with a rider who can cooperate. Make
sure the rider can easily remove the belts in an emergency.
5. NEVER Use Positioning Belts:
H. TRANSIT USE
WARNING
a. As a patient restraint. A restraint requires a doctor’s order.
b. On a rider who is comatose or agitated.
c. As a motor vehicle restraint. In an accident or sudden stop the
rider may be thrown from the chair. Wheelchair seat belts will
not prevent this, and further injury may result from the belts or
straps.
1. If possible and feasible, the rider
should transfer to the Original
Equipment Manufacturer vehicle
seat and use the vehicle restraint.
2. If the wheelchair is used for trans-
port, it must be used in a forward-
facing seating position.
Front
securement
point
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
3. The rider must not weight more
than 265 lbs.
4. The figures to the right show the
locations of the wheelchair secure-
ment points.
K. PUSH HANDLES (OPTIONAL)
WARNING
5. Use only with Wheelchair Tiedown
and Occupant Restraint Systems
(WTORS) that have been installed
in accordance with the manufactur-
er’s instructions and SAE J2249.
6. Attach WTORS to securement
points in accordance with the man-
ufacturer’s instructions and SAE
J2249.
7. Attach occupant restraints in accor-
dance with the manufacturer’s
instructions and SAE J2249.
NOTE– To obtain a copy of SAE J2249 Wheelchair Tiedown and Occupant
Restraint Systems for Use in Motor Vehicles, please contact: SAE
International, 400 Commonwealth Drive, Warrendale, PA 15096,
Phone: (412) 776-4970.
When you have an attendant, make sure that this chair has push handles.
1. Push handles provide secure points for an attendant to hold the rear
of this chair, to prevent a fall or tip-over. Make sure to use push han-
dles when you have an attendant.
2. Check to make sure push handle grips will not rotate or slip off.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
Rear
securement
point
L. QUICK-RELEASE AXLES
WARNING
1. Do not use this chair UNLESS you are sure that both quick-release
rear axles are locked. An unlocked axle may come off during use and
cause a fall.
2. An axle is not locked until the quick-release button pops out fully. An
unlocked axle may come off during use, resulting in a fall, tip-over or
loss of control and cause severe injury to the rider or others.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
•
Quick-Release Axles should be inspected for function and any
signs of wear or bending. Replace as necessary.
Routinely Inspect. Replace if worn or bent.
I. TRANSIT OPTION
•
WARNING
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
1. Use only Wheelchair Tiedown and Occupant Restraint Systems
(WTORS) which meet the requirements of SAE J2249
Recommended Practice - Wheelchair Tiedown and Occupant
Restraint Systems For Use in Motor Vehicles. Do not use WTORS
designed to rely on the wheelchair structure to transfer occupant
restraint loads to the vehicle.
M. REAR WHEELS
WARNING
A change in set-up of the rear wheels will affect the center of balance of
your chair.
2. The wheelchair has been dynamically tested in a forward-facing
mode for a 48 km/h frontal impact test. The wheelchair must be for-
ward-facing during transport.
3. In order to reduce the potential of injury to vehicle occupants,
wheelchair-mounted accessories, such as trays and respiratory equip-
ment, should be removed and secured separately.
4. Postural supports and positioning devices should not be relied on for
occupant restraint.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
1. The farther you move the rear axles FORWARD, the more likely it is
that your chair will tip over backward.
2. Consult your doctor, nurse or therapist to find the best rear axle set-up
for your chair. Do not change the set-up UNLESS you are sure you are
not at risk to tip over.
3. Adjust the rear wheel locks after you make any change to the rear
axles.
a. If you fail to do so, the locks may not work.
b. Make sure lock arms embed in tires at least 1/8 inch when
locked.
J. POSITIONING BELTS (OPTIONAL)
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
WARNING
Use positioning belts ONLY to help support the rider’s posture. Improper
use of these belts may cause severe injury to or death of the rider.
1. Make sure the rider does not slide down in the wheelchair seat. If
this occurs, the rider may suffer chest compression or suffocate due
to pressure from the belts.
2. The belts must be snug, but must not be so tight that they interfere
with breathing. You should be able to slide your open hand, flat,
between the belt and the rider.
N. REAR WHEEL LOCKS
WARNING
Rear wheel locks are NOT designed to slow or stop a moving wheelchair.
Use them only to keep the rear wheels from rolling when your chair is at a
complete stop.
1. NEVER use rear wheel locks to try to slow or stop your chair when
it is moving. Doing so may cause you to veer out of control.
2. To keep the rear wheels from rolling, always set both rear wheel
locks when you transfer to or from your chair.
3. A pelvic wedge or a similar device can help keep the rider from slid-
ing down in the seat. Consult with the rider’s doctor, nurse or thera-
pist to find out if the rider needs such a device.
108590 Rev. A
11
Download from Www.Somanuals.com. All Manuals Search And Download.
VIII.
3. Low pressure in a rear tire may cause the wheel lock on that side to
slip and may allow the wheel to turn when you do not expect it.
4. Make sure lock arms embed in tires at least 1/8 inch when locked. If
you fail to do so, the locks may not work.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
O. MODIFIED SEAT SYSTEMS
WARNING
Use of a seat system not approved by Sunrise may alter the center of bal-
ance of this chair. This may cause the chair to tip over.
1. Do not change the seat system of your chair UNLESS you consult
your authorized supplier first.
2. Use of a seat system not approved by Sunrise may affect the folding
mechanism of this chair.
3. Use of a seating system not provided by Sunrise is prohibited for
transit use.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
P. UPHOLSTERY FABRIC
WARNING
1. Replace worn or torn fabric of seat and seat back as soon as you can.
If you fail to do so, the seat or seat back may fail.
2. Sling fabric will weaken with age and use. Look for fraying, thin
spots, or stretching of fabrics especially at edges and seams.
3. “Dropping down” into your chair will weaken fabric and result in the
need to inspect and replace the seat more often.
4. Be aware that laundering or excess moisture will reduce flame retar-
dation of the fabric.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
108590 Rev. A
12
Download from Www.Somanuals.com. All Manuals Search And Download.
IX. SET-UP, ADJUSTMENT & USE
NOTE ON TORQUE SETTINGS: A torque setting is the optimum tightening which should be made on
a particular fastener. It is important to use proper torque settings where specified.
1
2
3
1
2
A. TO MOUNT & REMOVE REAR WHEELS
WARNING
A
Do not use this chair UNLESS you are sure both quick-release axles are locked.
An unlocked axle may come off during use and cause a fall.
NOTE– Setting the wheelchair on a flat surface, such as a workbench or table, helps make these
procedures easier.
1. To Install Wheel
C
a. Depress quick-release button (A) fully. This will release tension on ball bearings at other end.
b. Insert axle (B) through hub of rear wheel.
c. Keep button (A) depressed as you slide axle (B) into axle sleeve (C).
d. Release button to lock axle in axle sleeve. Adjust axle if it does not lock. See Section B.
e. Repeat steps on other side.
NOTE– The axle is not locked until the quick-release button pops out fully (A). Check that the axle is
locked by pulling on the wheel in the direction of the axle.
B
2. To Remove Wheel
a. Depress quick-release button (A) fully.
b. Remove wheel by sliding axle (B) completely out of axle sleeve (C).
c. Repeat steps on other side.
E
B
F
3
4
B. REAR WHEEL AXLE NUT ADJUSTMENT
The rear wheel axle (B) attaches the rear wheel (D) to the axle sleeve (C). When the detent balls (E)
engage into the camber plug the rear wheel effectively becomes locked onto the chair. Pushing the
quick-release button (A) disengages the detent balls and allows removal of the axle and wheel assembly.
A
To adjust the axle you will need a 3/4" wrench to turn the adjustment nut (F). You will also need a 1/2"
wrench to securely hold the ball detent end of the axle to prevent it from turning.
4
If the wheel and axle will not lock into the axle sleeve then the axle requires adjustment. Turn the nut
counter-clockwise approximately 1/4 revolution and try to lock the axle into the camber plug. If it does-
n't lock, continue making small nut adjustments until it securely locks.
C
If the wheel is locked on the chair but there is excessive wheel play (the wheel hub can be pushed back
and forth on the axle) then adjust the nut clockwise until there is no perceptible gap between the wheel
and camber tube and the axle is securely locked onto the chair.
A
D
CAUTION– Quick-release button (A) must be flush with the edge of the wheel hub for detent balls (E) to be
engaged.
5
H
G
5
C. PADDED SWING-AWAY ARMRESTS (OPTIONAL)
Swing-away armrests can be detached or can swing away to allow lateral transfers. They are height
adjustable (1" increments) by moving bolt (G) up or down in predrilled holes on armrest bracket.
J
Additional height can be achieved by removing bolts (I), flipping and rotating the hardware to opposite
(J). Ensure bolts (I) are retighten.
I
Swing-away, removable armrests are installed by sliding armrest into receiver (H) on back frame.
1. Installation
Slide armrest into receiver tube on rear of frame.
2. Swinging Away
Lift armrest out of locked position and rotate to the side.
3. Removing Armrest
Pull armrest straight out of receiver.
108590 Rev. A
13
Download from Www.Somanuals.com. All Manuals Search And Download.
IX.
4
6
6
6a
D. HEIGHT-ADJUSTABLE ARMRESTS (OPTIONAL)
1. Installation
2
5
a. Slide the outer armpost into the receiver mounted to the wheelchair frame.
b. The armrest will automatically lock into place.
6
2. Height Adjustment
a. Rotate release lever to second stop.
b. Slide armrest pad up or down to desired height.
c. Return lever to locked position against armpost.
d. Push arm pad until upper armpost locks firmly into place.
1
3
9
9
3. Removing Armrest
a. Rotate release lever to first stop and remove the armrest.
6a
7
7
1. Outer armpost
2. Release Lever–
Height
3. Release lever
4. Armrest pad
5. Transfer bar
6. Side panel
7. Receiver
8
4. Replacing Armrest
a. Slide armrest back into receiver.
b. Return release lever to locked position against armpost.
5. Adjusting Armrest Receiver Fit
To tighten or loosen the fit of the outer armpost in the receiver:
a. Loosen the bolts on the sides of the receiver.
b. With the armrest in the receiver, squeeze the receiver to achieve the desired fit.
c. Tighten the four bolts.
8. Clamp
9. Receiver adjustment
hardware
E. SWING-IN/SWING-OUT HANGERS AND FOOTRESTS
(70º, 80°)
7
7
1. Installation
A
a. Place swing-in/swing-out pivot saddle into the receiver on front frame tube with the footrest
7
facing outward from the frame. (
-A)
7
b. Rotate the footrest inward until it locks into place on locking bolt. (
-B)
B
2. Removal
a. To remove footrest, push release latch toward the frame.
b. Rotate footrest inward and lift. Or, pull footrest away from frame and rotate outward.
8
3. Height Adjustment
NOTE– It is recommended that you maintain a minimum of 2.0 inches between the lowest point on the
footrest and the floor.
8
a. Loosen set screw (C) using a 3/16 inch hex key.
b. Slide footrest extension up or down inside frame tube to desired height.
c. Tighten set screw. Use a torque setting of 144 in-lbs (16.27 Nm).
C
9
F. FIXED FRONT FOOTREST HEIGHT ADJUSTMENT
Using a 3/16 inch hex key, loosen the screw (D) on both sides of the footrest. Slide the footrest up or
down to the new desired height and tighten the two screws back into place. Use a torque setting of 144
in-lbs (16.27 Nm). It is recommended that you maintain a minimum of 2.0 inches between the lowest
point on the footrest and the floor. Additionally, both sides of the footplate should be of equal height.
This will provide adequate clearance for uneven surfaces and prevent damage to your footrest.
9
NOTE– Footrest must be in locked position before riding in wheelchair.
D
108590 Rev. A
14
Download from Www.Somanuals.com. All Manuals Search And Download.
IX.
G. ANGLE ADJUSTABLE FOOTPLATES
10
11
10
1. Composite Angle Adjustable Footplates
a. Remove bolt (A)
B
C
b. Pull footplate section (B) away from extension.
c. Reposition footplate back onto extension in new angular position. Use premarked extension
coupling (C) as guide.
A
11
2. Aluminum Angle Adjustable Footplate
a. Loosen bolts (D).
D
E
b. Adjust footplate (E) to desired angular position.
c. Re-tighten bolt (D).
12
H. BACKREST
1. Height Adjustment
a. Remove the backrest upholstery from the frame.
b. You will see the backrest tube which telescopes into the frame and is secured by a screw (F) on
the side of the frame.
c. There are holes 1 inch apart that you may choose from to set the back height.
d. Remove the two backrest bolts from the rear frame tubes.
e. After selecting the proper height, insert bolt through frame and backrest tube.
f. Slide the backrest upholstery back over both backrest tubes.
12
13
14
15
F
I. ANGLE ADJUSTABLE BACKREST (OPTIONAL)
13
1. Angle Adjustment
a. Loosen button head screws (G) until the eccentric offset washer (H) moves freely.
b. Adjust backrest to desired angle, aligning eccentric offset washer in slot.
c. Tighten button head screws.
G
H
d. Repeat for opposite side.
14
2. Pivot Point Height Adjustment
a. Remove button head screws (I) from the frame.
b. Adjust backrest to obtain desired pivot point height.
c. Replace and tighten button head screws.
d. Repeat for opposite side.
15
3. Backrest Height Adjustment
a. Remove button head screw (J).
b. Adjust back tube to desired height.
c. Replace and tighten button head screw.
d. Repeat for opposite side.
I
J
108590 Rev. A
15
Download from Www.Somanuals.com. All Manuals Search And Download.
IX.
J. SEAT SLING
16
The seat sling can be adjusted through the use of hook and loop material beneath the seat.
16
Seat sling also includes a folding strap on the seat to assist in folding the chair.
NOTE– The seat sling folding strap is not intended as a carrying strap.
A
16
Adjustment
a. Remove seat rail end caps at the front of the chair (A).
b. Slide the seat sling, plastic retaining rods, and spacers (if present) from the channels in the seat
rails.
c. Readjust hook and loop material to obtain the desired tension in the seat sling.
d. Reinsert the seat sling and plastic retaining rods into the channels in the seat rails.
e. Replace the end caps.
K. CUSHION INSTALLATION (OPTIONAL)
a. Place cushion on seat sling with hook material side down. The beveled edge of the cushion should
be in front.
b. Press firmly into place.
L. REAR AXLES
The most important adjustment on your Quickie wheelchair is the position of the rear axle. The center
of gravity, wheel camber and wheelbase are all determined by the axle adjustment.
17
B
Use a torque setting of 100 in.-lbs. when adjusting rear axle.
WARNING
The more you move your rear wheels forward, the more likely your chair will tip
over backwards. Always make adjustments in small increments, and check the sta-
bility of your chair with a spotter to prevent a tip-over. We recommend that you
use anti-tip tubes until you adapt to the change and are sure you are not at risk to
tip over. Refer to additional Warnings in Section VI “Falls and Tip-Overs”.
C
NOTE– Adjusting your chair’s center of gravity will require re-adjsuting the location of the wheel locks
(if provided). See Section Q for instructions on adjusting the wheel locks.
18
17
1. Center of Gravity
Moving the center of gravity to the front will lighten the force required to turn the chair. The further
back the axle, the more stable the chair becomes.
a. Remove four retaining bolts (B), nuts and camber spacers on axle plate (C).
b. Move axle plate forward or rearward to desired position.
c. Insert all four bolts and camber spacers back into place on frame. Tighten nuts.
d. Repeat on opposite side of wheelchair.
e. Axle plate and camber must be exactly the same on both sides of the wheelchair.
E
F
18
2. Wheel Camber
D
The wheel camber adjustment provides greater side-to-side stability due to the increased width and
angle of the wheelbase. The wheel camber adjustment also allows for quicker turning and greater access
to the top of the handrims.
19
More or less camber can be obtained by increasing or decreasing the number of camber spacers (D)
located between the lower axle plate attachment (E) and frame (F).
3. Wheel Base Width Adjustment
Adjusting the wheelbase width allows the rider the option to move the wheels closer or further away
from the hips. It also compensates for camber adjustment and gives the proper wheel spacing to maxi-
mize pushing efficiency.
G
19
H
Adjust the wheelbase width by:
a. Loosen the nuts (G) and reposition the axle sleeve (H) to the desired width.
b. Retighten nuts.
108590 Rev. A
16
Download from Www.Somanuals.com. All Manuals Search And Download.
IX.
Adjustment with Anti Tip Hardware:
NOTE– Before adjusting wheel base estimate distance the rear wheels need to move in or outward.
a. Remove outside nut.
20
b. Remove anti tip receiver hardware with axle sleeve.
c. Thread axle sleeve in or out as desired, ensuring that the final position leaves the flats of the axle
sleeve parallel to the rear of the anti tip receiver.
d. Insert anti tip receiver hardware with axle sleeve through desired hole of the axle plate from the
inside of the wheelchair.
e. Re-install and tighten outside nut.
A
f. Repeat on opposite side of wheelchair.
20
4. Seat Height Adjustment
Seat height can be adjusted by repositioning the axle sleeve (A) vertically in one of the predrilled holes in
the axle plate. Switch axle plates left to right (and upside down) for 1/2" adjustments.
NOTE– A front caster adjustment should be made to correspond with any change in seat height.
21
M. WHEEL LOCKS
The Quickie 2 Lite wheelchair is shipped with one of four types of wheel locks. Wheel locks are installed at
the factory unless you have requested otherwise.
Use a torque setting of 144 in.-lbs. when setting up wheel locks.
21
1. High-Mount Push-to-Lock or Pull-to-Lock
, Wheel Locks Adjustment
a. Using a 3/16 inch hex key, turn one of the screws in the clamp counterclockwise one-quarter
turn.
b. Repeat the same process with the second of the two screws.
c. Alternately loosen the screws (two turns each) until both screws are removed.
d. Slide clamp toward the rear wheel until the wheel lock is embedded into the tire to prevent
wheel movement, when in the locked position.
22
e. Tighten screws to 144 in-lbs.
B
22
2. Ergo Scissor Wheel Locks
or Short Throw Scissor Wheel Locks
Loosen the screws (B) on the top of each clamp using a 3/16 inch hex key. Slide assembly toward rear
wheel until clamp embeds into tire to prevent wheel movement when in locked position. Adjust angle posi-
tion. Tighten screws to 144 in-lbs.
NOTE– Clamp and wheel lock may need to be rotated to clear frame tubing.
N. CASTERS
23
NOTE– Setting the wheelchair on a very flat table or a workbench makes this setting more accurate.
NOTE ON TORQUE SETTING– A torque setting is the optimum tightening which should be made on a par-
ticular fastener. Use proper torque settings when specified.
23 24
1. Adjusting Caster Angle
Checking for Caster Squareness:
Your Quickie wheelchair leaves the factory with the casters adjusted square. Any time you change your
wheelchair rear axle height, rear tire size, center of gravity position or camber tube, you should check
that the casters are still square. A caster that is not square will result in the caster lifting off the floor as it
23
rotates around the stem bolt
and may also lift the front of the wheelchair up and down. Check for
24
squareness by placing your wheelchair on a flat, horizontal surface. Rotate both forks so that the casters
are towards the rear of the wheelchair. Place a square or pocket level against the flat surface on the rear
0° to 2° MAX
24
of the fork and note whether this surface is vertical (square)
away from vertical, your casters require re-squaring.
. If this surface is more than 2 degrees
108590 Rev. A
17
Download from Www.Somanuals.com. All Manuals Search And Download.
IX.
A
25
25 26
2. Re-squaring Your Casters
Gently pry cap (A) off of both caster tubes. Locate the set screw (B) inside the right caster tube and
loosen using an 1/4 inch hex key. Do not remove the set screw. Simply loosen it enough to allow the
teeth on the upper and lower splines (C) to clear one another. With the stem bolt loosened, the caster
fork should pivot freely. Place the wheelchair on the floor so that the two rear wheels and left caster con-
tact the floor. Place some weight in the seat towards the rear to help stabilize the chair. Place a square or
B
24
pocket level against the flat surface of the fork and pivot the fork until it is vertical (square)
. With the
fork vertical, engage the teeth of the two splines to the closest mating position. Make certain that the
teeth are properly engaged and not crossed. Shine a bright light behind the mating spline teeth and check
for proper teeth engagement. Tighten the set screw (B) to secure the spline mating position. The set
screw should be tightened to 192 in-lbs. (21.7 Nm) to ensure that it does not loosen during use.
26
Record the teeth engagement position of the splines on the right fork, and adjust the left fork in a similar
fashion to the same position. Reassemble both casters, and re-check that they are square. Replace caps.
27
3. Fixed Front Frame Caster Housing Adjustment
C
To reposition the caster housing hardware for Quickie 2 Lite Fixed Front
a. Remove cotter clip (D) from pin (E).
b. Using a 7/16 wrench remove two caster housing bolts (F)
c. Remove clivis pin (E).
d. Reposition caster housing hardware onto frame lining up with preset holes.
e. Insert clivis pin (E) , insert and retighten two caster housing bolts (F)
f. Reinsert cotter clip (D)
27
E
F
WARNING
After repositioning the caster housing always check for interference with footrest
or rear wheel. Do not operate a wheelchair that has interference with these
components. Ensure the caster fork is square (see section “N” for caster squaring
instructions). Additionally, repositioning the caster housing will affect the wheel-
chair’s stability. Check the stability of your wheelchair with a spotter to prevent
a tip-over.
D
28
O. ANTI-TIP TUBES (OPTIONAL)
Quickie recommends anti-tip tubes for all wheelchairs.
Use a torque setting of 100 in.-lbs. when setting up the anti-tip tubes.
28
H
1. Inserting Anti-Tip Tubes Into Receiver
G
a. Press the rear anti-tip release pin (G) on the anti-tip tube so that both release pins are drawn
inside.
b. Insert into the anti-tip tube receiver.
c. Turn the anti-tip tube down until release pin is positioned through the receiver mounting hole (H).
d. Insert second anti-tip tube the same way.
29
29
2. Adjusting Anti-Tip Tube Wheel
The anti-tip tube wheels may have to be raised or lowered to achieve proper clearance of 1 1/2" to 2".
a. Press the anti-tip wheel release pin (I) so that the release pin is drawn inside.
b. Raise or lower to one of the three predrilled holes.
c. Release pin.
d. Adjust the second anti-tip tube wheel the same way.
Both wheels should be at exactly the same height.
I
30
3. Turning Anti-Tip Tubes Up
Turn anti-tip tubes up when being pushed by attendant, overcoming obstacles or climbing curbs.
a. Press the rear anti-tip tube release pin (J).
b. Hold pin in and turn anti-tip tube up.
30
c. Release pin.
d. Repeat with second anti-tip tube.
e. Remember to return anti-tip tubes to down position after completing maneuver.
J
108590 Rev. A
18
Download from Www.Somanuals.com. All Manuals Search And Download.
IX.
31
31
P. PLASTIC SIDE GUARDS (OPTIONAL)
Installation of side guard hardware.
a. Position outer receiver hardware (A) on frame.
b. On corresponding inside of the frame position inner clamping hardware (B)
c. Insert two bolts with washer and tighten using 3/16 inch hex key
D
C
Inserting and Removing of Side Guard
a. Insert Side Guard (D) into Side Guard outer receiver hardware (A)
b. Remove, clutch top of Side Guard and pull upward.
B
NOTE – After installing receiver hardware and inserting side guard check for interference. Don’t operate the
A
wheelchair that as interference with these other components.
Q. FOLDING AND UNFOLDING
1. Folding Chair
a. Remove quick-release wheels (optional).
•
•
•
Depress quick-release button on the axle.
Remove wheel by sliding out quick-release axle from axle bracket.
Repeat with other wheel.
b. For the Q2 Lite Swing Away model, flip up the footrest to a vertical position before folding the
wheelchair.
c. Grasp the seat sling (in the center) and lift sharply until the wheelchair is folded.
2. Unfolding Chair
a. Replace quick-release wheel (optional) by depressing the quick-release button on the axle.
b. Slide it into the axle sleeve until it locks.
c. Repeat with other wheel.
d. Tilt the wheelchair toward you far enough to take the weight off the opposite wheel.
e. Push down on the seat rail (closest to you) until the wheelchair is completely opened.
f. Make sure seat rail tubes are resting in the seat rail saddles.
NOTE– Ensure that footrest is locked prior to use.
R. CHECK-OUT
After the wheelchair is assembled and adjusted, it should roll smoothly and easily. All accessories should
also perform smoothly. If you have any problems, follow these procedures:
1. Review the set-up and check-out sections and operating guide to make sure chair was
properly prepared.
2. Review troubleshooting guide.
3. If your problem persists, contact your authorized supplier. If you still have a problem
after contacting your authorized supplier, contact Sunrise customer service. See the
introduction page for details on how to contact your authorized supplier or Sunrise cus-
tomer service.
108590 Rev. A
19
Download from Www.Somanuals.com. All Manuals Search And Download.
X. TROUBLESHOOTING
You will need to adjust your chair from time to time for best performance (especially if you alter the
original settings). This chart gives you a first solution, then a second and a third if needed. You may
need to look farther to find the best solution for a specific problem.
NOTE– To keep track of your progress, make only ONE change at a time.
Solution
Make sure tire pressure is correct and equal in both
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
rear tires and front caster tires, if pneumatic.
ꢀ
ꢀ
ꢀ
Make sure all nuts and bolts are snug.
Make sure all spokes and nipples are tight on
radial spoke wheels.
Use Tri-Flow Lubricant (Teflon®-based) between
all modular frame connections and parts.
ꢀ
Check for proper caster fork adjustment.
See instructions for caster fork adjustment.
ꢀ
ꢀ
ꢀ
ꢀ
108590 Rev. A
20
Download from Www.Somanuals.com. All Manuals Search And Download.
XI. MAINTENANCE
A. INTRODUCTION
1. Proper maintenance will improve performance and extend the useful
life of your chair.
C. MAINTENANCE TIPS
1. Axles & Axle Sleeves:
Check axles and axle sleeves every six months to make sure they are tight.
Loose sleeves will damage the axle plate and will affect performance.
2. Clean your chair regularly. This will help you find loose or worn parts
and make your chair easier to use.
3. Repair or replace loose, worn, bent or damaged parts before using
this chair.
4. To protect your investment, have all major maintenance and repair
work done by your authorized supplier.
2. Tire Air Pressure:
Check air pressure in pneumatic tires at least ONCE A WEEK. The wheel
locks will not grip properly if you fail to maintain the air pressure shown on
tire sidewall.
WARNING
If you fail to heed these warnings your chair may fail
and cause severe injury to the rider or others.
1. Inspect and maintain this chair strictly per maintenance
chart.
2. If you detect a problem, make sure to service or repair the
chair before use.
D. CLEANING
1. Paint Finish
a. Clean the painted surfaces with mild soap at least once a month.
b. Protect the paint with a coat of non-abrasive auto wax every three
months.
2. Axles and Moving Parts
a. Clean around axles and moving parts WEEKLY with a slightly damp
(not wet) cloth.
3. At least once a year, have a complete inspection, safety check
and service of your chair made by an authorized supplier.
B. MAINTENANCE CHART
b. Wipe off or blow away any fluff, dust or dirt on axles or moving
parts.
NOTE– You do not need to grease or oil the chair.
3. Upholstery
a. Hand-wash (machine washing may damage fabric).
b. Drip-dry only. DO NOT machine dry as heat will damage fabric.
E. STORAGE TIPS
Check...
1. Store your chair in a clean, dry area. If you fail to do so, parts may
rust
ꢀ
ꢀ
Tire inflation level
Wheel locks
or corrode.
2. Before using your chair, make sure it is in proper working order.
Inspect and service all items on the “Maintenance Chart”.
3. If stored for more than three months, have your chair inspected by
an authorized supplier before use.
ꢀ
All fasteners for wear and tightness
Armrests
ꢀ
ꢀ
Axle and axle sleeves
Quick-release axles
Wheels, tires and spokes
Casters
ꢀ
ꢀ
ꢀ
ꢀ
Anti-tip tubes
ꢀ
Frame and crossbrace
Upholstery
ꢀ
ꢀ
Service by Authorized Supplier
108590 Rev. A
21
Download from Www.Somanuals.com. All Manuals Search And Download.
XII. SUNRISE LIMITED WARRANTY
A. FOR LIFETIME
D. WHAT WE WILL DO
Sunrise warrants the frame and cross brace if applicable of this wheelchair
against defects in materials and workmanship for the life of the original pur-
chaser.
Our sole liability is to repair or replace covered parts. This is the exclusive
remedy for consequential damages.
E. WHAT YOU MUST DO
The expected life of this frame is five years.
1. Obtain from us, while this warranty is in effect, prior approval for
return or repair of covered parts.
B. FOR ONE (1) YEAR
We warrant all Sunrise-made parts and components of this wheelchair
against defects in materials and workmanship for one year from the date of
first consumer purchase.
2. Return the wheelchair or part(s), freight pre-paid, to Sunrise Mobility
Products Division at: 2842 Business Park Avenue, Fresno, CA 93727-
1328.
3. Pay the cost of labor to repair, remove or install parts.
F. NOTICE TO CONSUMER
C. LIMITATIONS
1. If allowed by law, this warranty is in place of any other warranty
(written or oral, express or implied, including a warranty of mer-
chantability, or fitness for a particular purpose).
1. We do not warrant:
a. Tires and tubes, upholstery, pads and push-handle grips.
b. Damage from neglect, accident, misuse, or from improper instal-
lation or repair.
c. Products modified without Sunrise Medicals express written
consent.
2. This warranty gives you certain legal rights. You may also have other
rights that vary from state to state.
d. Damage from exceeding the weight limit.
2. This warranty is VOID if the original chair serial number tag is
removed or altered.
3. This warranty applies in the USA only. Check with your supplier to
find out if international warranties apply.
4. This warranty is not transferable and only applies to the first con-
sumer purchase of this wheelchair through an authorized Sunrise
Medical dealer.
Record your serial number here for future reference:
____________________________________________
108590 Rev. A
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Sunrise Medical Inc.
7477 East Dry Creek Parkway
Longmont, Colorado 80503
USA
(800) 333-4000
In Canada (800) 263-3390
©2008 Sunrise Medical Inc. 8.08
108590 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
|