All-Weather Outdoor LCD Television
Operator’s Manual
Model 3230HD
Revision 3230HD-T-101105
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
Cleaning instructions: Use a soft cloth with mild detergent in warm water to clean the SunBriteTV screen. Remove any dirt and
salt deposits from the unit, being careful to rinse the cloth frequently to avoid scratching the screen surface. Avoid using harsh
chemicals, abrasives, or solvents when cleaning any surface on the screen. Use a soft brush or towel to remove snow and ice from
the TV. In areas where dust or salt air is prevalent, it is recommended that the fiber filter be cleaned regularly (see instructions on
Page 41).
attachments: Do not use attachments not specifically recommended by the manufacturer. Use of improper attachments can
result in accidents.
Power source: SunBriteTV must operate on a power source indicated on the specification label. If you are not sure of the type of
power supply used in your home, consult your dealer or local power company. When using the TV outdoors, you must use a GFI-
protected AC outlet with “in-use”waterproof cover.
installation: Do not place the product on an unstable cart, stand, tripod, table, or anywhere the unit is not permanently installed.
Placing the product on an unstable place can cause the product to fall, resulting in potential serious personal injuries, as well as
damage to the product.
Precautions when Transporting the TV: Carrying the television requires at least two people.
FCC statement
This equipment complies with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses, and can radiate radio frequency energy
and, if not installed and used in accordance with
the instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment
and receiver.
3. Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
4. Consult the dealer or an experienced radio/TV
technician for help.
Modifications not expressly approved by the
manufacturer could void the user’s authority to
operate the equipment under FCC rules. This device
complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation.
SunBriteTV Model 3230HD Operator’s Manual
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
Ventilation: Adequate ventilation must be maintained to ensure reliable and continued operation and to protect
the television from overheating. Do not block ventilation slots and openings with objects, or install the television in
a place where ventilation may be hindered. sunBriteTV is not designed for built-in installation. Do not place the
product in an enclosed place such as bookcase or rack.
Power cord protection: The power cord must be routed properly to prevent people from stepping on it, or objects
from resting on it. Check the cords at the plugs and product.
Power source: This product must operate on a power source specified on the specification label. If you are unsure of
the type of power supply used in your home, consult your dealer or local power company.
Do not let metal pieces or objects of any kind fall into the television from ventilation holes. High voltage flows in the
product, and inserting an object can cause electric shock and/or short internal parts.
Do not mount sunBriteTV near a motor or transformer where strong magnetism is generated. Images on the
television will become distorted and the color irregular.
Do not mount sunBriteTV near heat sources such as radiators, heaters, stoves and other heat-generating products
(including amplifiers).
Do not submerge sunBriteTV in water: The SunBriteTV will resist water exposure from normal rain, sprinklers,
garden hoses, etc.; However, it is not designed to be submerged in water.
Do not pressure-wash sunBriteTV: SunBriteTV will resist water exposure from normal rain, sprinklers, garden hoses,
etc.; However, it is not designed to withstand pressure washers, high-pressure water jets, or hurricane-type weather.
Do not service sunBriteTV yourself: Removal of the television screen cover may expose you to high voltage or other
dangerous risks. Refer all servicing to a qualified service professional. Warranty will not be honored if you service the
unit yourself.
repair: If any of the following conditions occurs, unplug the power cord, and call a qualified service professional to
perform repairs:
When power cord or plug is damaged.
When objects have fallen into the product.
If unit was submerged in water or pressure-washed.
When product does not operate properly as described in the operating instructions. Do not touch the controls other
than as described in the operating instructions. Improper adjustments of controls not described in the
instructions can cause damage, which can require extensive repair work by a qualified technician.
When the product has been dropped or damaged.
When the product displays an abnormal condition. Any noticeable abnormality in the product indicates that the
product needs servicing.
replacement parts: In case the product needs replacement parts, make sure that the service person uses
replacement parts provided by SunBriteTV. Use of unauthorized parts can result in fire, electric shock and/or other
danger.
safety checks: Upon completion of service or repair work, ask the service technician to perform safety checks to
ensure that the product is in proper operating condition.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Important Safety Instructions
Table of Contents
2
5
6
Supplied Accessories
TV Installation
Choose a Location for the TV
Table-top Stand Instructions
Rear Panel Internal Connect Source
Rear Panel Connections
Connecting the Power Cord
Side Panel Controls and Front Panel
Remote Control Guide
Adjusting On-Screen Displays
On-Screen Display Menu
Picture Menu
6
7
8
9
19
19
19
22
22
23
24
25
27
30
32
33
34
34
Audio Menu
Time Menu
Set-up Menu
Lock Menu
Channel Menu
Trouble Shooting
Care of SunBriteTV
Specifications
VGA Timing Codes
Features Information and Instructions
Internal Thermostatically-Controlled Heater
Programming Other Manufacturers’Universal Remote Control Devices
SunBriteTV Pixel Quality Policy
35
35
35
SunBriteTV Model 3230HD Operator’s Manual
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Supplied Accessories
Unpacking
After unpacking the SunBriteTV television, please make sure that the following items are included in the carton and
that they are in good condition. If items are damaged or missing, contact your dealer immediately.
SunBriteTV LCD Television Model 3230HD
Remote Control with Batteries
Operator’s Manual
Table Stand Installation Kit
Operator’s
Manual
Water-Resistant
Wireless Remote
Control
Model 3230HD
NEW PHOTOS
TV Installation - Choose a Location for the TV
Choose a location for the TV
Important: The TV must be installed at least 5
feet from pool, spa, or other body of water.
The TV should be installed so the screen is not facing
direct sunlight, or can be easily turned away from
direct sunlight.
Ideal placement is in an area where the TV is shaded
by trees, landscape and/or structures, or under a patio
cover or gazebo.
If the sun shines directly on the screen for long periods
of time, dark areas may develop on the screen. This is a
normal reaction for the LCD panel, and will not cause
damage to the screen. Either turn the screen away from
the sun, or apply shade to the TV, and the dark areas
will quickly disappear.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation - Table-top Stand Installation
Figure 1
Table Top Stand Installation
TV’s Table-top Stand
Mounting Screws
WARNING: To prevent personal injury and/or
damage to the TV or personal property, use at
least two people to install or move the TV.
TV’s Table-
top Stand
Mounting
Niche
Tools Needed: Phillips screwdriver
Notes:
Do not attach the Table-top Stand if you plan to install the TV on a wall
mount or ceiling mount.
Figure 2
For demonstration purposes, this manual is showing how to install the right-
half of the Table Stand. Because you will be working from the back of the TV,
the Table Stand will appear on the left.
Table-top Stand
Table-top Stand
Mounting
1. Prepare a flat work surface, free of any debris or items which may scratch the
front surface of the TV.
Catches
2. Lay the TV face-down on the work surface with the bottom of the unit closest
to you
WARNING: Use at least two people when transporting the TV.
Table-top Stand
Mounting Holes
3. Position the TV so that the bottom edge overhangs the table by about two
inches.
4. The TV is shipped with two Table-top Stand Mounting Screws on each side
of the TV. There are two Mounting Niches at the bottom of the TV on each side
(Figure 1).
Align
Mounting
Holes
Figure 3
5. Temporarily remove the Table-top Stand Mounting Screws. (Figure 1).
Note: Never permanently remove the Mounting Screws (or any
screws) from the TV.
Slide Table-top
Stand’s Mounting
Catch into
6. The Table-top Stand has adjacent Mounting Holes, and a set of two Mounting
Catches (Figure 2).
TV’s Mounting Niche
7. Align the Table-top Stand Mounting Holes with the TV Mounting Holes, and
align the Table-top Stand’s Mounting Catch to the TV’s Mounting Niche. Slide
the Catch into the Niche (Figure 3).
8. Replace the Table-top Stand Mounting screws to attach the Table-top Stand
to the TV and secure tightly (Figure 4).
Figure 4
9. Follow procedures 4 thru 8 to install the other Table-top Stand.
SunBriteTV Model 3230HD Operator’s Manual
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation – Rear Panel Internal Connect Source
WARNING: Do not connect the power source before making connections.
Internal Connect Source
The Internal Connect Source allows you to easily connect to the Audio, Video, S-Video, SVGA, HDMI, Audio Out, and RF connectors.
The Internal Connect Source is inside the Cable Cover located on the back of the unit (Figure1).
1. Unscrew the two gray Thumb Screws (Figure1), and pull the cover towards you.
2. Route the cables to the proper inputs, and place the cable cords over the Rubber Sealing Gasket (Figure 2).
3. Close the cover.
4. Press firmly on the cover, and screw the Thumb Screws tightly (Figure3).
Figure 1
Figure 2
Rubber Sealing Gasket
Thumb Screws
Figure 3
Thumb Screw
TV Installation - Connecting the Power Cord
Do not connect power cord until all cable connections have been made.
Connect the power cord to a GFCI protected AC outlet with an “in-use” waterproof cover.
WARNING:
TV AND GFCI RECEPTACLE MUST BE INSTALLED AT LEAST 5 FEET AWAY FROM STANDING WATER , SUCH AS (BUT NOT LIMITED
TO) A POOL OR SPA.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation – Rear Panel Connections
Rear View Connections
13.
Please Note:
This TV features a power-saving function that will turn off the TV automatically after 15
minutes of idling on a connection with no signal. This feature is present on all connections.
SunBriteTV Model 3230HD Operator’s Manual
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation – Rear Panel Connections
Red
Green
Blue
Yellow
Green
Red
White
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation – Rear Panel Connections
Switching Sources for Ports:
Model 3230HD offers several options when connecting
your devices to the TV. The chart below will help you
understand which source you switch to for each of the
ports.
COnneCTing TO an anTenna
Connecting to Digital Cable without Cable Box or Antenna
Connecting to Cable or Antenna
1. Make sure the power of the TV is turned off.
1. Make sure the power to the TV is turned off.
2. Connect the Coaxial RF cable from your
antenna or digital cable to the ATSC/NTSC port off
the back of the TV.
2. Connect the Coaxial RF cable from your
antenna or cable to the
ATSC/NTSC port off the back of the TV.
3. Turn on the TV.
3. Turn on the TV.
4. Select TV (Air) for antenna or TV (Cable) for
digital cable from either your remote control’s
source button or source button on the right side
of the TV.
4. Select TV (Air) for antenna or TV (Cable) for
cable from either your remote control’s source
button or source button on the right side of the
TV.
5. Use the On-Screen Display to scan for channels.
5. Use the On Screen Display to scan for channels.
Please Note :
1. Not all broadcasts are in High Definition (HD). Please refer to your local broadcasting stations for more information.
2. The TV’s tuner is designed for HDTV therefore requires a stronger signal than normal TVs. If you cannot achieve that
signal level with your antenna or cable, the TV might lose picture or sound.
SunBriteTV Model 3230HD Operator’s Manual
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation – Rear Panel Connection Diagrams
COnneCTing TO an anTenna--(Continued)
Connecting to Cable or Antenna through VCR
Please Note :
1. Some VCRs must be turned On before its output will have
a signal to the TV. Please consult your VCR manual for further
reference.
1. Make sure the power of the TV is turned off.
2. Make sure there is an antenna or cable
connection to the VCR already.
2. Not all broadcasts are in High Definition (HD). Please refer to
your local broadcasting stations for more information.
3. Use a Coaxial RF cable and connect from your
VCR’s Antenna Out or Output to TV to the ATSC/
NTSC port of your TV.
3. The MODEL 5510HD’s tuner is designed for HDTV therefore
requires a stronger signal than normal TVs. If you cannot achieve
that signal level with your antenna or cable, the TV might lose
picture or sound.
4. Turn on the TV.
5. Select TV (Air) for antenna or TV (Cable) for
digital cable from either your remote control’s
source button or source button on the TV.
4. This TV will turn off automatically if there’s no signal present
for more than 15 minutes.
6. Use the On-Screen Display to scan for channels.
COnneCTing TO a DVD Player
Connecting with
Component (Better)
Connecting with HDmi (Best)
1. Make sure the power of TV and your DVD player is turned off.
2. With a Component Cable, connect the green connector to the
DVD player and Component 1’s green connector port on the TV.
1. Make sure the power of the TV and your DVD player is
turned off.
3. Connect the blue color connector to your DVD player and
Component 1’s blue connector port on the TV.
2. Connect a HDMI cable to the HDMI port of your DVD
player and the other end to the HDMI port off the back of
your TV.
4. Connect the red color connector to both your DVD player and
Component 1’s red connector port on the TV.
5. With an RCA Audio Cable, connect the white color connector to
both your DVD player and Component 1’s white connector port on
the TV.
3. Turn on the TV and your DVD player.
4. Use the remote control’s source button or the source
button on the TV to switch to HDMI.
6. Connect the red color connector to both your DVD player and
Component 1’s red connector port on the TV.
Please Note :
Refer to the DVD player’s manual to make sure the DVD player
is configured to output correctly to the TV.
7. Turn on the TV and your DVD player.
8. Use the remote control’s source button or the source button on
the TV to switch to YPbPr1.
Please Note :
Please Note :
1. Refer to the DVD player’s manual to make sure the DVD
player is configured to output correctly to the TV.
1. If Component 1 is already occupied, please use Component 2 as
your connection port and switch to source YPbPr2.
2. This TV does not decode Bit stream digital audio, so make
sure the DVD is setup for PCM digital audio through HDMI.
2. Refer to the DVD player’s manual to make sure the DVD player
is configured to output correctly to the TV.
3. If HDMI 1 is occupied, use HDMI 2 as your connection port.
4. This TV will turn off automatically if there’s no signal present for
more than 15 minutes.
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation – Rear Panel Connection Diagrams
COnneCTing TO a DVD Player (Continued)
Connecting with
Composite (Fair)
Connecting with s-Video (fair)
1. Make sure the power of the TV and your DVD player is turned
off.
1. Make sure the power of the TV and your DVD player is
turned off.
2. Obtain a Yellow Video Cable. Connect the Yellow Video
connector to both your DVD player and Composite’s Yellow Video
connector port off the back of your TV.
2. Obtain an S-Video Cable. Connect the S-Video connector
to both your DVD player and Composite’s S-Video connector
port off the back of your MODEL 5510HD.
3. Obtain a RCA Audio Cable. Connect the white color
connector to both your DVD player and Composite’s white
connector port off the back of your TV.
3. Obtain a RCA Audio Cable. Connect the white color
connector to both your DVD player and Composite’s white
connector port off the back of your MODEL 5510HD.
4. Connect the red color connector to both your DVD player
and Composite’s red connector port off the back of your TV.
4. Connect the red color connector to both your DVD player
and Composite’s red connector port off the back of your TV.
5. Turn on the TV and your DVD player.
5. Turn on the TV and your DVD player.
6. Use the remote control’s source button or the source button
on the right side of the TV to switch to AV1 (CVBS).
6. Use the remote control’s source button or the source
button on the right side of the TV to switch to AV1 (S-Video).
Please note:
1. If AV 1 is already occupied, use AV2, as your connection port, and switch source to AV 2 (S-Video)
2. Reference the DVD player’s manual to make sure the DVD player is configured to output correctly to the TV.
3. This TV will turn off automatically if there’s no signal present for more than 15 minutes.
SunBriteTV Model 3230HD Operator’s Manual
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation – Rear Panel Connection Diagrams
COnneCTing TO a saTelliTe Or CaBle seT-TOP BOX
Connecting with HDmi (Best)
Connecting with
Component (Better)
1. Make sure the power of the TV and your set-top box is
turned off.
1. Make sure the power of TV and your set-top box is turned off.
2. Obtain a Component Cable. Connect the green color
connector to both your set-top box and Component 1’s green
connector port off the back of your TV.
2. Connect a HDMI cable to the HDMI output of your set-top
box and the other end to the HDMI port off the back of your
TV.
3. Connect the blue color connector to both your set-top box
and Component 1’s blue connector port off the back of your TV.
3. Turn on the TV and your set-top box.
4. Use the remote control’s source button or the source
button on the right side of the TV to switch to HDMI 1.
4. Connect the red color connector to both your set-top box and
Component 1’s red connector port off the back of your TV.
Please Note :
5. Obtain a RCA Audio Cable. Connect the white color connector
to both your set-top box and Component 1’s white connector port
off the back of your TV to the right side of your green, blue, red
component connection.
1
Refer to the set-top box’s manual, to make sure the set-
top box is configured to output correctly to the TV.
2. If HDMI 1 is already occupied, use HDMI 1 as your
connection port and switch source to HDMI 2.
6. Connect the red color connector to both your set-top box and
Component 1’s red connector port off the back of your TV to the
right side of your green, blue, red component connection.
3
SunBriteTV’s MODEL 5510HD supports SONY’s universal
remote code. Please look up SONY’s codes in your universal
remote’s hand book.
7. Turn on the TV and your set-top box.
4. This TV will turn off automatically if there’s no signal
present for more than 15 minutes.
8. Use the remote control’s source button or the source button
on the TV to switch to YPbPr1.
Please Note :
1. If Component 1 is already occupied, please use Component 2
as your connection port and switch to source YPbPr2.
2. Please refer to the set-top box’s manual to make sure the set-
top box is configured to output correctly to the TV.
3. SunBriteTV’s MODEL 5510HD supports SONY’s universal
remote code. Please look up SONY’s codes in your universal
remote’s hand book.
4. This TV will turn off automatically if there’s no signal present
for more than 15 minutes.
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation – Rear Panel Connection Diagrams
COnneCTing TO a saTelliTe Or CaBle seT-TOP BOX (Continued)
Connecting with
Composite (Fair)
Connecting with s-Video (Fair)
1. Make sure the power of the TV and your DVD player is
turned off.
1. Make sure the power of the TV and your DVD player is
turned off.
2. Obtain a Yellow Video Cable. Connect the Yellow Video
connector to both your DVD player and Composite’s Yellow
Video connector port off the back of your TV.
2. Obtain an S-Video Cable. Connect the S-Video connector
to both your DVD player and Composite’s S-Video connector
port off the back of your MODEL 5510HD.
3. Obtain a RCA Audio Cable. Connect the white color
connector to both your DVD player and Composite’s white
connector port off the back of your TV.
3. Obtain a RCA Audio Cable. Connect the white color
connector to both your DVD player and Composite’s white
connector port off the back of your MODEL 5510HD.
4. Connect the red color connector to both your DVD player
and Composite’s red connector port off the back of your TV.
4. Connect the red color connector to both your DVD player
and Composite’s red connector port off the back of your TV.
5. Turn on the TV and your DVD player.
5. Turn on the TV and your DVD player.
6. Use the remote control’s source button or the source
button on the right side of the TV to switch to AV1 (CVBS).
6. Use the remote control’s source button or the source
button on the right side of the TV to switch to AV1 (S-Video).
Please Note :
Please Note :
1. If AV 1 is already occupied, use AV 2 as your connection
port and switch source to AV 2 (S-Video).
1. If AV 1 is already occupied, use AV 2 as your connection
port and switch source to AV 2 (S-Video).
2. Refer to the set-top box’s manual to make sure the set-top
box is configured to output correctly to the TV.
2. Refer to the set-top box’s manual to make sure the set-top
box is configured to output correctly to the TV.
3. SunBriteTV’s MODEL 5510HD supports SONY’s universal
remote code. Please look up SONY’s codes in your universal
remote’s hand book.
3. SunBriteTV’s MODEL 5510HD supports SONY’s universal
remote code. Please look up SONY’s codes in your universal
remote’s hand book.
4. This TV will turn off automatically if there’s no signal present
for more than 15 minutes.
4. This TV will turn off automatically if there’s no signal
present for more than 15 minutes.
SunBriteTV Model 3230HD Operator’s Manual
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation – Rear Panel Connection Diagrams
COnneCTing TO an eXTernal amPliFier Or amPliFieD sPeaKers
Connecting with Coaxial sPDiF Digital (Best)
Connecting with rCa audio analog (good)
1. Make sure the power of the TV and your receiver is turned
off.
1. Make sure the power of the TV and your receiver is turned off.
2. Obtain a Coaxial SPDIF cable, connect it to your receiver’s
coaxial SPDIF digital input and the Coaxial SPDIF connection
on the LINE OUT port off the back of the TV.
2. Obtain a 3.5mm stereo/audio cable (if your amplifier
audio connection requires RCA audio out jacks you will need
to obtain an 1/8”Stereo Mini Plug to RCA adapter cable).
Connect it to your receiver’s audio input connection and the
3.5mm stereo/audio connection on the Analog Audio port on
the back of the TV.
3. Turn on the TV and your receiver.
Please Note :
1. If you want pure digital stream for your receiver to
decode, you must also configure the TV’s OSD Sound->Digital
Audio Out function. Make sure the option is on Bit Stream.
3. Turn on the TV and your receiver.
Please Note :
2. If your receiver is making static noises when receiving Bit
Stream, you must use the PCM option instead.
1. If you want pure digital stream for your receiver to
decode, you must also configure the TV’s OSD Sound->Digital
Audio Out function. Make sure the option is on Bit Stream.
3. Refer to the receiver’s manual to make sure the receiver is
configured to receive signals correctly from the TV
2. If your receiver is making static noises when receiving Bit
Stream, you must use the PCM option instead.
3. Refer to the receiver’s manual to make sure the receiver
is configured to receive signals correctly from the TV
COnneCTing TO a PC
1. Make sure the power of the TV and your receiver is turned off.
Connecting with DVi Digital (Best)
2. Obtain a HDMI to DVI conversion cable; connect the DVI side
of the conversion cable to the DVI output of your PC, and the HDMI
side of the conversion cable to the HDMI port off the back of TV.
3. Obtain a 3.5 mm Mini-jack, connect to the audio out of your PC
and the other end to the VGA Stereo Input Port.
4. Turn on the power to the TV and the PC.
5. From the remote control’s source button, or the Source button
from the TVs panel, switch to HDMI.
Please Note :
1. For the best picture, set your PC resolution to 920 x 1080 at 60
Hz. Refer to the PC or graphic card manual for further instructions
on how to set your resolution and refresh rate.
2. Refer to your PC manual for video output requirements of the
video card.
3. The TV will turn off automatically if there’s no signal present for
more than 15 minutes.
4. If HDMI 1 is already occupied, use HDMI 2 as your connection
port, and switch source to HDMI 2.
Continued on next page
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation – Rear Panel Connection Diagrams
COnneCTing TO a PC (Continued)
1. Make sure the power of the TV and your PC is turned off.
Connecting with rCa audio analog (good)
2. Obtain a 15-pin D-Sub VGA cable, connect to the VGA output of
your PC and the other end to the VGA port off the back of your TV.
3. Obtain a 3.5 mm Mini-jack, connect to the audio out of your PC
and the other end to the VGA Stereo Input port.
4. Turn on the power of the TV and your PC.
5. Use the remote control’s source button or the source button the
TV to switch to VGA.
Please Note :
1. For the best results, please set your PC resolution to
1920 x 1080at 60 Hz. Refer to the PC or graphic card’s manual for
further instructions on how to set your resolution and refresh rate.
2. Refer to your PC manual for video output requirements of the
video card.
3. The VGA port of the TV features a power saving mode which will
automatically turn off the TV if there is no signal provided for more
than 15 minutes.
COnneCTing TO game COnsOles
1. Make sure the power of the TV and your Playstation 3 is turned off.
2. Connect an HDMI cable to the HDMI output of your Playstation 3
and the other end to the HDMI port on the back of the TV.
For the Playstation®3
3. Turn on the TV and Playstation 3.
4. Use the remote control source button or the source button on the
power panel of the TV to switch to HDMI.
Please Note :
1. Refer to the Playstation 3’s manual to make sure the PS3 is
configured to output correctly to the TV. PS3 by default outputs to
composite only. With newer firmware, PS3’s HDMI should also output a
signal. Please call PS3’s tech support for further troubleshooting.
2. This TV does not decode Bit stream digital audio, therefore you’ll
need to make sure your DVD is set up for PCM digital audio through
HDMI.
3. If HDMI 1 is already occupied, please use HDMI 2 as your
connection port and switch source to HDMI 2.
4. This TV will turn off automatically if there’s no signal present for
more than 15 minutes.
SunBriteTV Model 3230HD Operator’s Manual
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation – Rear Panel Connection Diagrams
COnneCTing TO game COnsOles (Continued)
1. Make sure the power of the TV and your Xbox 360 is turned off.
2. Obtain the Xbox 360 Component Cable. Connect the green color
connector to Component 1’s green connector port on the back of
the TV.
For the Xbox™
3. Connect the blue color connector to Component 1’s blue
connector port on the back of the TV.
4. Connect the red color connector to the Component 1 red
connector port on the back of the TV.
5. Connect the white color connector to the Component 1 white
connector port on the back of TV.
6. Connect the red color connector to the Component 1 red
connector port on the back of the TV
7. Connect the gray head to the Xbox 360 and make sure the
switch on the head is switched to HD.
8. Turn on the TV.
9. Use the remote control source button or the source button on
the TV panel to switch to YPbPr1.
Please Note :
1. Make sure not to confuse the red connector for video with the
red connector for audio, they are on separate rows on the Xbox 360’s
connector.
2. If component 1 is already occupied, use Component 2 as your
connection port and switch to source YPbPr2.
3. Refer to the Xbox 360 manual to make sure the Xbox 360 is
configured to output correctly to the TV.
4. This TV will turn off automatically if there’s no signal present for
more than 15 minutes.
1. Make sure the power of the TV and your Wii is turned off.
For the Wii™
2. Obtain a yellow video cable. Connect the yellow video
connector to both your Wii and the AV 1 yellow video connector port
on the TV.
3. Obtain a RCA Audio Cable. Connect the white color connector to
both the Wii and the AV 1 white video connector port on the TV.
4. Connect the red color connector to both your Wii and the AV 1
red video connector port on the TV.
5. Turn on the TV and the Wii.
6. Use the remote control source button or the source button on
the TV panel to switch source to AV 1 (CVBS).
Please Note :
1. If AV 1 is already occupied, use AV 2 as your connection port and
switch source to AV 2 (CVBS).
3. Refer to the Wii manual to make sure the Wii is configured to
output correctly to the TV.
4. This TV will turn off automatically if there’s no signal present for
more than 15 minutes.
Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation - Connecting the Power Cord
Connecting the Power Cord
WARNING:
TV AND GFCI RECEPTACLE MUST BE INSTALLED AT LEAST 5 FEET AWAY FROM STANDING WATER , SUCH AS (BUT NOT LIMITED
TO) A POOL OR SPA.
Connect the power cord after you have made connections to your video equipment.
Connect the power cord to a GFCI-protected AC outlet
with “in-use”waterproof cover.
Warning: TV must be installed at least 5 feet away from
standing water, such as (but not limited to) a pool or
spa.
Side Panel Controls
Power
Input
Turn on the TV by pressing the button once. Press the button again to
turn off the TV.
This button switches between the different sources of the TV. When the
On-Screen Display (OSD) is active, this button acts as the enter button
and confirms the menu selection.
Menu
This button activates the OSD. If a sub-menu is active, pressing this
button will return selection to the previous menu level.
CH+/CH-
Vol+ /Vol-
These buttons change the TV channel up or down. If the OSD is active,
these buttons function as up or down controls for the menu.
These buttons increase or decrease the volume. If a sub-menu is active,
pressing these buttons will move the selection left or right.
Front Panel
IR Sensor
SunBriteTV Model 3230HD Operator’s Manual
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control Guide
ON – Powers the TV On.
OFF – Powers the TV Off.
0~9 – Allows you to set the channels directly. To access a digital channel, use these
buttons with the (-) button to switch channels.
Dash (-) – Insert the dash for selecting digital channels directly.
R – Returns to the previous channel.
FREEZE – Freezes the TV picture. Press the button again to unfreeze the picture.
SLEEP– Sets time for the TV to turn Off.
CC– Selects Closed Caption (CC only works under sources TV, AV1 and AV2.)
V+ – Functions the Volume Up.
V- – Functions the Volume Down.
MUTE – Mutes the TVs Audio.
MENU – Opens / Exits the TV menu.
CH+ – Functions the Channel Up.
CH- – Functions the Channel Down.
MTS – Selects stereo, mono, or second audio programming.
h / i / f / g / – Allow you to navigate inside the OSD menu. They also function
as CH+/- and Vol +/-.
– Allows you to select functions inside the OSD menu, acts as the Enter button
for OSD menu for changing channels.
SOUND – Selects various preset sound settings.
EXIT – Exits the TV menu.
PICTURE – Selects various preset picture settings.
GUIDE –Opens the current digital channel information guide.
SOURCE – Cycles between different input sources of the TV.
INFO – Shows current channel information, display input and resolution.
SHIFT – Used with the 0-9 numeric pad to select inputs
ASPECT – Selects different screen sizes
FAVORITE – Cycles the favorite channels.
FAVORITE ADD / DEL – Adds or deletes the current channel from the favorites
channel list.
The following functions (illustrated with bold squares on the remote) are not
applicable to the SunBriteTV 23/32xx Series:
SRS
DNR
ADD/Del
CH Lock
The Picture in Picture/Picture On Picture functions Audio, Video, Source,
On/Off, Size and Pos
About the Water-Resistant Remote Control
®
The SunBriteTV Water-Resistant Remote Controller is engineered to give you many years of service.
“Water-resistant”means that the remote control can be in water for short periods of time without damaging the internal workings of the unit. It
can be left in the rain, and even dropped in water, as long as it is retrieved quickly. The remote control should not be left floating in water.
The functionality of the remote control is under warranty for one year. If the remote control malfunctions within the one-year warranty period,
replace the batteries with new long-life alkaline batteries.
If the problem is not solved with new batteries, contact the SunBriteTV Customer Support Team. SunBriteTV will repair or replace the remote
control at SunBriteTV’s option.
If you have a warranty claim, contact the SunBriteTV Customer Support Team for further instructions.
866.357.8688
Page 20
Download from Www.Somanuals.com. All Manuals Search And Download.
On-Screen Display Controls
SunBriteTV Model 3230HD Operator’s Manual
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
On-Screen Display Menu - Picture Menu
Picture:
This function
changes
the picture
settings for all
ports, such as
tint, contrast,
sharpness and
dynamic noise
reduction.
audio:
This menu
manages
the audio
settings such
as Bass, Treble,
Balance, AVC,
SPDIF, Audio
Language, etc.
Time:
This menu
setup:
This menu
manages
Language,
Transparency,
Zoom Mode,
Noise Reduction,
lock:
Channel:
This menu
manages Channel
functions such
as scanning
channels, editing
channels,
This menu
manages
parental
controls.
manages the
time functions
such as Sleep
Timer, Time
Zone, Daylight
Saving Time, and Closed Caption,
Clock. etc.
checking signal
strength, etc.
Adjusting On-Screen Displays – Picture Menu
Picture menu
From the PICTURE menu you can adjust PICTURE MODE, CONTRAST, BRIGHTNESS, COLOR, TINT SHARPRESS, COLOR MODE.
Picture mode
1. Press qp buttons to move the cursor to the item to be selected.
Press qp buttons to Picture Mode, then use t u to
adjust the Picture Mode such as Personal/Standard/
Dynamic/Soft.
2. Press t u buttons to make the desired adjustments.
3. When you are satisfied with your adjustments, press MENU or EXIT
to exit the main menu.
Contrast
Picture menu
Press qp buttons to Contrast, then use t u to
adjust the contrast of the picture.
Brightness
Press qp buttons to Brightness, and use t u to
adjust the brightness of the picture.
Color
Press qp button to Color, then use t u to adjust the
color saturation.
Tint
Press qp button to Tint, then use t u to adjust the
tint of picture.
This function is available in the NTSC, which is one of
the color systems.
sharpness
Press qp buttons to Sharpness, then use t u to
adjust the sharpness level of picture.
Color mode
Press qp buttons to Color Mode, then use t u to
adjust the color mode of picture, such as Cool, Normal
and Warm
Page 22
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting On-Screen Displays – Audio Menu
audio menu
1. Press qp buttons to move the cursor to the item to be selected.
sound mode
Allows you to you choose your sound preferences.
2. Press t u buttons to make the desired adjustments.
Press qp buttons to Sound Mode, then use t u to
adjust the Sound Mode such as Personal/Standard/
Music/Movie.
3. When you are satisfied with your adjustments, press MENU or EXIT
to exit the main menu.
sound mode
Bass
Press qp buttons and then use t u button to increase
or decrease the level of the Bass response.
Treble
Press qp buttons and then use t u buttons to
increase or decrease the level of the Treble sounds.
Balance
Pressd qp buttons and then use t u buttons to
adjust the audio output level between Left and Right
Speakers.
surround
Surround Sound is not supported on this model.
aVC
Press qp buttons and then use t u buttons to select
AVC On or Off.
sPDiF
Press qp buttons and then use t u buttons to select
SPDIF Type, such as PCM and RAM.
audio language
Press qp buttons to select one of the audio languages
such as English/French/Spanish.
The language code must be programmed for this option
to be available. If there is no selection it has not been
programmed for this model.
Note: SPDIF Type and Audio Language are available only
in DTV.
SunBriteTV Model 3230HD Operator’s Manual
Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting On-Screen Displays – Time Menu
Time menu
sleep Timer
1. Press qp buttons to move the cursor to the item to be selected.
Press qp buttons to Sleep Timer, then use t u
buttons to select the sleep timer. The options are:
Off; 5Min; 10Min; 15Min; 30Min; 45Min; 60Min;
90Min; 120Min; 180Min; 240Min.
2. Press u buttons to make the desired adjustments.
3. When you are satisfied with your adjustments, press MENU or EXIT
to exit the main menu.
Time menu
Time Zone
Press qp buttons to Time Zone, then use t u
buttons to select the correct time zone. The options
are: Alaska; Hawaii; Pacific; Mountain; Central;
Eastern.
Daylight saving Time
Press qp buttons and then use t u buttons to
select Daylight Saving Time ON or OFF.
When Daylight Saving Time is ON, the clocks are set
one hour ahead of local standard time.
Clock
The time is decoded from the digital signal and
displayed (such as DTV,HDMI)
This item is available only in English.
Page 24
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting On-Screen Displays – Setup Menu
setup menu
1. Press qp buttons to move the cursor to the item to be selected.
menu language
Press qp buttons to Menu Language, then use t
u buttons to select menu language, the options are
English / French / Spanish.
2. Press t u buttons to make the desired adjustments.
3. When you are satisfied with your adjustments, press MENU or EXIT
to exit the main menu.
setup menu
Transparency
Press qp buttons to Transparency, then use t u
buttons to select Transparency ON or OFF.
Zoom mode
Press qp buttons to Zoom Mode, then use t u
buttons to select current zoom mode, the options are
Normal / Wide / Zoom / Cinema.
noise reduction
Press qp buttons to Noise Reduction, then use t u
buttons to select current noise reduction level, the
options are off / Weak / Middle / Strong.
advanced
Press qp buttons to Advanced, then press u button
to enter the Advanced Sub Menu shown below
Note: This item is only available in VGA source input.
advanced sub menu
H-Pos
Press qp buttons and then use t u adjust the
horizontal position of the picture (this function
is to adjust the picture to Left/Right as to your
preference).
V-Pos
Press qp buttons and then use t u adjust
the vertical position of the picture (to adjust the
picture to Left/Right as to your preference).
Clock
Press qp buttons and then use t u to adjust
the clock of the picture. (This function is to
minimize any vertical bars or stripes visible on
the background screen. The horizontal screen
size will also change.
Phase
Press qp buttons and then use t u to adjust
the phase of the picture. (This function allows
you to remove any horizontal noise and to
sharpen the image of characters).
auto
Press qp buttons and then press OK button
to perform the Auto Adjust function that
automatically adjusts the available options for
the best viewing configuration.
SunBriteTV Model 3230HD Operator’s Manual
Page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting On-Screen Displays – Setup Menu
Closed Caption
From the Setup Menu, press qp buttons to Closed Caption, then press u button to enter the Closed Caption submenu list shown
below.
Closed Caption submenu
Basic selection
Press qp buttons and then use t u buttons
to select current zoom mode, the options are
CC1 / CC2 / CC3 / CC4 / TEXT1 / TEXT2 / TEXT3 /
TEXT4.
advanced selection
Press qp buttons and then use t u buttons
to select current zoom mode, the options are
Service1 / Service 2 / Service 3 / Service 4 /
Service 5 / Service 6.
Option
Press the u button to enter the submenu list
shown below.
Closed Caption/Optionsub-menu
mode: Press qp keys to select either Default
and Custom. If you set Automatic, the other
choices are disabled and can’t be adjusted.
Font style: press t u keys to select one of the
Defaults and from Font0 to Font7.
Font size: press t u to select one of Default /
Normal / Large / Small.
Font edge style: press t u keys to select
one of Default / None / Raised / Depressed /
Uniform / Left Shadow / Right Shadow.
Font edge Color: press t u keys to select one
of Default / Black / White / Red / Green / Blue /
Yellow / Magenta / Cyan.
Fg Color: press t u keys to select one of
Default / White / Black / Red / Green / Blue /
Yellow / Magenta / Cyan.
XVs submenu
Bg Color: press t u keys to select one of
Default / Black / White / Red / Green / Blue /
Yellow / Magenta / Cyan.
Fg Opacity: press t u to select one of Default
/ Solid / Flashing / Translucent / Transparent.
Bg Opacity: press t u to select one of Default
/ Solid / Flashing / Translucent /Transparent.
XVs (Dynamic luminance Control)
From the Setup Menu, press qp buttons to XVS, to enter the
XVS menu. Use the t u buttons to select ON or OFF.
Page 26
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting On-Screen Displays – Lock Menu
lock menu
Press qp buttons to move the cursor to the Enter
Password selection.
Press “Enter Password”to enter the password. (The
default password is 0000.)
To change the Password, press the u button to
enter the Lock Menu submenu
lock menu sub-menu
Change password
Press u button to enter the submenu. Once
there, you can enter the new password and
confirm it. The password will be changed.
Note: If you change the password, write down
the new password, and keep it in a safe place
system lock
Press qp buttons and then use t u
buttons to select system lock ON or OFF.
When system lock is OFF, the item choices
are: US / Canada / RRT setting / Reset RRT
will be grayed
Us
Press the u button to enter the submenu list
to set the US rating functions. (US Menu is
on the next page.)
SunBriteTV Model 3230HD Operator’s Manual
Page 27
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting On-Screen Displays – Lock Menu
Us menu
From the US Menu, press qp buttons to the TV function.
Press u button to enter the submenu shown below.
TV menu
TV-y: For all children
TV-y7: For children above 7
TV-g: For anyone
TV-Pg: Children can watch with guardian
TV-14: Need parent guide
TV-ma: Only for adult
all: Select all functions above
FV: Fantasy Violence
l: Language (abusive, sexual)
s: Sexual
V: Violence
D: Dialog (sexual)
Us menu
mPaa
From the Us Menu, press qpbuttons and use t u
buttons to select one of N/A / G / PG / PG-13 / R / NC-17
/ X.
Page 28
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting On-Screen Displays – Lock Menu
lock menu sub-menu
Canada
Press the u button to enter the submenu for the
Canadian rating functions.
Canada menu
Canada english
Press the t u button to select one of E / C /
C8+ / G / PG / 14+ / 18+.
Canada French
Press the t u button to select one of E / G /
8ans+ / 13ans+ / 16ans+ / 18ans+.
SunBriteTV Model 3230HD Operator’s Manual
Page 29
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting On-Screen Displays – Channel Menu
Channel menu
1. Press qp buttons to move the cursor to the item to be selected.
2. Press t u buttons to make the desired adjustments.
3. When you are satisfied with your adjustments, press MENU or EXIT
to exit the main menu.
Channel menu
The CHANNEL MENU is used in TV source, only.
You can complete channel search and settings here
air/Cable
Press t u buttons to select Air or Cable.
auto scan
Press the u button to enter the submenu list below
auto scan
Cable system
Press the t u button to select the cable system.
start to scan
Press the u button to start auto scan.
Page 30
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting On-Screen Displays – Channel Menu
Favorite
Favorite
From the Channel Menu, press the qp buttons
to select Favorite. Press the u button to enter the
submenu shown at left.
Press qp keys to select channels, and press OK to
add current channel to Favorite Channel Table.
Follow the same directions to delete a channel from
the Favorite Channel Table.
show/Hide menu
show/Hide
From the Channel Menu, press the qp buttons to
select Show/Hide. Press the u button to enter the
submenu (shown left).
Press qp keys to your desired channel. Press OK
to show or hide the specified channel.
If the channel is Hidden, user will be unable to
see the channel by pressing CH+ or CH-. They can
select the channel by pressing the channel number
directly.
Channel menu
From the Channel Menu, press the qp buttons to
select the following functions:
Channel no.
Press the t u button to select the channel No.
Channel label
Press the u button to enter the submenu, where you
can edit the channel label.
DTV signal
This item shows current DTV signal strength.
SunBriteTV Model 3230HD Operator’s Manual
Page 31
Download from Www.Somanuals.com. All Manuals Search And Download.
Trouble Shooting
The following table contains the common problems and the solutions to these problems. Please check this list before you contact
the technicians.
Page 32
Download from Www.Somanuals.com. All Manuals Search And Download.
Care of SunBriteTV
important information about the anti-reflective Window on your sunBriteTV
Outdoor Television
The anti-reflective window on your all-weather TV is designed to dramatically reduce reflection and improve the contrast of
the image on your TV. In order to preserve the anti-reflective properties of the window, it is imperative that you follow the
maintenance guidelines below:
1. Clean the window by using the following directions:
Do not use abrasive cleaners or acrylic cleaning products to clean the window, as they may damage the anti-reflective
surface. For best results, use a damp, lint-free cloth with mild soap.
2. When the TV is not in use, keep it covered with the sunBriteTV Outdoor Dust Cover
The fitted dust cover is constructed with weatherproof 4-ply polypropylene UV protection fabric that protects the window
from direct and indirect sunlight, and keeps wind-blown objects from scratching the surface of the window.
To order the Dust Cover, contact your Authorized SunBriteTV dealer or SunBriteTV’s Customer Service at 866.357.8688.
General Cleaning
Remove any dirt and salt deposits from the unit, being careful to rinse the cloth frequently to avoid scratching the TV or screen
surface. Avoid using harsh chemicals, abrasives, or solvents when cleaning any surface on the unit.
Snow and Ice
Use a soft brush and towel to remove snow and ice from the unit.
Fiber Filters
The Fiber Filters are located on the back of the TV, inside the Intake Vent at the top of the TV (Figure 1). In areas where dust or salt air
is prevalent, it is recommended that the Fiber Filters be cleaned regularly.
1. Release the Fiber Filters by pulling them out from the corner of the Intake Vent (Figure 2).
2. Pull the Fiber Filters out of the TV, and wash them with mild detergent and warm water. After rinsing, let them dry completely.
3. Put the Fiber Filters back up into the Intake Vent. Make sure the filters fits snuggly and fill the entire space of the Intake Vent
(Figure 4).
Figure 1
Intake Vent
Figure 2
Fiber Filter
Fiber Filter
Figure 3
Figure 4
SunBriteTV Model 3230HD Operator’s Manual
Page 33
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
specifications
LCD Screen
31.5-inch diagonal TFT Active Matrix
1366 x 768
sunBriteTV model 3230HD
(all dimensions are in inches)
Resolution
Aspect Ratio
Contrast Ratio
H/V Viewing Angle
Response Time
TV formats
16:9
Front View
side View
3000:1
178o by 178o
6.5 milliseconds
1080i, 720p, 480i, 480p
Input Connectors:
RF
Antenna/CATV (NTSC/ATSC/QAM)
HDMI Input x2
HDMI
Video Composite
S-Video x1 and Composite Video x1, L/R Audio Inputs x1
Video Component
YCbCr/YPbPr x2 and audio L/R channels x2
15-pin D-sub VGA plus Stereo Audio
TV Dimensions are:
32.21 in. W x 23.21 in. H x 6.97 in. D
Height dimension with table top stand is 24.22 in.
Depth dimension with table top stand is 11.14 in.
PC
Output Connectors:
SPDIF digital audio out
Analog audio out (1/8”stereo mini jack)
Input Power
Audio
100-240 VAC, 50-60 Hz 2.5A Max
8-watt x 2 channels, water-resistant speaker module
(detachable), SPDIF Audio output connector inside rear cover,
3.5mm analog stereo audio jack with variable output.
-24o to 122o F. (-31o to 50o C.)
-24o to 140o F. (-31o to 60o C.)
Operating Temp.
Non-op. Temp.
(Off-mode with
power applied)
Accessories Included
Water-resistant remote control with battery
Removable table top stand
TV Dimensions
Weight
32.21 in. W x 23.21 in. H x 6.97 in. D
39.0 lbs., 42 lbs. with table top stand
37.0 in. W x 31.0 in. H x 11.7 in. D
50 lbs.
Shipping Dimensions
Shipping Weight
Warranty
One-year, in-factory, parts and labor
Temperature range is for operation in shaded location
Under all conditions, the LCD TV should be installed in a shaded area where the screen is not facing direct sunlight (or placed/mounted
where the TV can easily be turned away from direct sunlight).
Vga Timing Codes
Page 34
Download from Www.Somanuals.com. All Manuals Search And Download.
Features Information and Instructions
internal Thermostatically-Controlled Heater
The Internal Thermostatically-Controlled Heater keeps the unit warm in freezing temperatures and activates automatically when the
SunBriteTV internal temperature sensor reads a temperature inside the unit of 32O F. or lower. The heater remains on until the internal
temperature rises to at least 42O F. The heater provides a 20O F. temperature rise, allowing the TV to safely remain in temperatures as low
as -24O F. The ventilation fans are not activated when the heater is running and will automatically activate when required.
If temperatures below -24O F. are expected, we recommend that you bring your SunBriteTV inside to prevent damage to the LCD screen.
WARNING: In order for the automatic heater to work properly, and to prevent damage to the TV, your SunBriteTV must have
power applied at all times (power cord must be connected to the GFCI protected AC outlet).
Programming Other manufacturers’ Universal remote Control Devices
When programming a DirectTV, local cable universal remote control or Control system, you may find that SunBriteTV may not be on the
list of TV manufacturers. If that is the case, Model 3230HD supports SONY’s universal remote code.
sunBriteTV Pixel Quality Policy
SunBriteTV’s Pixel Quality Policy
(Applicable to LCD TVs sold within USA and Canada only.)
SunBriteTVTM LCD screens are manufactured with rigorous standards to maintain optimal viewing. However, the LCD screen may
have minor defects that appear as a small bright or dark pixel. This is common to all LCD screens used in display and television
products, and is not specific to SunBriteTV.
Bright dots are dots that appear bright and unchanged in size when a LCD TV screen displays a black pattern.
Dark dots are dots that appear dark and unchanged in size when a LCD TV screen displays a pure red, green, or blue pattern.
Adjacent dots are pixels located directly next to each other.
Your SunBriteTV will be replaced under warranty if it meets one of the following criteria:
—A total of 7 defective pixels, including both bright dots and dark dots are present. (Model 3230HD LCD TV screen has over a million
pixels.)
—2 or more pairs of adjacent bright dots are present.
—3 adjacent bright dots are present.
—3 adjacent dark dots are present.
To locate defective pixels, the LCD panel should be examined under normal operating conditions, in its native display resolution,
with a 90 degree viewing angle, from a distance of a approximately 20 inches.
To qualify for replacement, a defective LCD screen must be reported to SunBriteTV within 14 days from the day the customer
receives the TV.
For questions, please call our toll-free service number at 866.357.8688.
SunBriteTV Model 3230HD Operator’s Manual
Page 35
Download from Www.Somanuals.com. All Manuals Search And Download.
|
