INSTRUCTION
MANUAL
650Line Intensifier3™ Series
Focus Free
HTD8FFI
(Weatherproof Color Dome Camera)
HTB11FFI
(Weatherproof Color Bullet Camera)
HT7248FFI
(Weatherproof Color Dome Camera)
Speco Technologies is constantly developing product improvements.
We reserve the right to modify product design and specifications without notice and without incurring any obligation.
Rev. 6/9/10
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions
Do not install the camera in
extreme temperature conditions.
Do not install the camera under
unstable lighting conditions.
Do not touch the front lens of the
camera.
Only use the camera under conditions
where temperatures are between
-10°C and +50°C. Be especially careful to provide
ventilation when operating under high
temperatures.
Severe lighting change or flicker can
cause the camera to work improperly.
This is one of the most important parts of the
camera. Be careful not to leave
fingerprints on the lens cover.
Never keep the camera pointed
directly at strong light.
Do not drop the camera or subject
it to physical shocks.
Do not expose the camera to
radioactivity.
It can cause malfunctions to occur.
Severe lighting change or flicker can
cause the camera to work improperly.
If exposed to radioactivity the CCD
will fail.
NOTE
* If the camera is exposed to
spotlight or object reflecting strong light, smear or blooming may occur.
* please check that the power satisfies the normal specification before
connecting the camera.
Download from Www.Somanuals.com. All Manuals Search And Download.
650 Line Intensifier3
(Weatherproof Color Dome Camera)
Focus free AI Motorized zoom Lens(2.8-10mm)
Focus Free
HTD8FFI
■
SPECIFICATIONS
MODEL
HTD8FFI
1/3” Sony Super HAD ll CCD
NTSC, PAL
NTSC=811(H) * 508(V) / PAL=795(H) * 596(V)
NTSC=768(H) * 494(V) / PAL=752(H) * 582(V)
NTSC=15.734KHz(H) & 59.94Hz(V) / PAL=15.625KHz(H) & 50.00Hz(V)
2:1 Interlace
Internal
650TV Lines
CDS OFF: 0.15 Lux, CDS ON: 0.00002 Lux
More than 52dB
CVBS: 1.0Vp-p / 75Ω
NTSC=(1/60sec~1/120,000sec) / PAL=(1/50sec~1/120,000sec)
Available
Image Pick-Up Device
TV System
Total Pixels
Effective Pixels
Scanning Frequency
Scanning System
Synchronization
Resolution
Minimum Illumination
S/N Ratio
Video Output
Electronic Shutter Speed
OSD
On / Off (Level adjustable)
BLC / HLC / OFF
Color / BW / AUTO
WDR
BLC
Day & Night
Low / High / Off
Gain Control
White Balance
Intensify
ATW / Outdoor / Indoor / Manual / AWC (1,700°K ~ 11,000°K)
Auto / Off (Selectable x2 ~ x512)
On / Off (8 Programmable Zones)
On / Off (12 Programmable Zones)
On / Off (Level adjustable)
On / Off (x1 ~ x16)
On / Off
On / Off (Level adjustable)
On / Off
DC 12V / AC24V(Dual Voltage)
DC 12V 250mA / AC24V 100mA
Focus free AI Motorized zoom Lens(2.8-10mm)
PELCO-D, PELCO-P, BOSCH, HONEYWELL, VICON, PANA, STW(SPD)
14~122ºF RH 95% Max
-4~140ºF RH 95% Max
5.51"(W) * 4.37"(H) * 5.51"(D)
3.08 lbs
Motion Detection
Privacy Masking
SPECO DNR
Digital Zoom
DIS (Digital Image Stabilization)
Sharpness
Flip / Mirror
Power Supply
Power Consumption
Lens
RS485(Option)
Operational Temp.
Storage Temp.
Dimension
Weight
Download from Www.Somanuals.com. All Manuals Search And Download.
650 Line Intensifier3
(Weatherproof Color Bullet Camera)
Focus free AI Motorized zoom Lens(2.8-10mm)
Focus Free
HTB11FFI
■
SPECIFICATIONS
MODEL
HTB11FFI
1/3” Sony Super HAD ll CCD
NTSC, PAL
NTSC=811(H) * 508(V) / PAL=795(H) * 596(V)
NTSC=768(H) * 494(V) / PAL=752(H) * 582(V)
NTSC=15.734KHz(H) & 59.94Hz(V) / PAL=15.625KHz(H) & 50.00Hz(V)
2:1 Interlace
Internal
650TV Lines
CDS OFF: 0.15 Lux, CDS ON: 0.00002 Lux
More than 52dB
CVBS: 1.0Vp-p / 75Ω
NTSC=(1/60sec~1/120,000sec) / PAL=(1/50sec~1/120,000sec)
Available
Image Pick-Up Device
TV System
Total Pixels
Effective Pixels
Scanning Frequency
Scanning System
Synchronization
Resolution
Minimum Illumination
S/N Ratio
Video Output
Electronic Shutter Speed
OSD
On / Off (Level adjustable)
BLC / HLC / OFF
Color / BW / AUTO
WDR
BLC
Day & Night
Low / High / Off
Gain Control
White Balance
Intensify
ATW / Outdoor / Indoor / Manual / AWC (1,700°K ~ 11,000°K)
Auto / Off (Selectable x2 ~ x512)
On / Off (8 Programmable Zones)
On / Off (12 Programmable Zones)
On / Off (Level adjustable)
On / Off (x1 ~ x16)
On / Off
On / Off (Level adjustable)
On / Off
DC 12V / AC24V(Dual Voltage)
DC 12V 250mA / AC24V 100mA
Focus free AI Motorized zoom Lens(2.8-10mm)
PELCO-D, PELCO-P, BOSCH, HONEYWELL, VICON, PANA, STW(SPD)
14~122ºF RH 95% Max
-4~140ºF RH 95% Max
3.46"(W) * 3.43"(H) * 11.22"(D)
3 lbs
Motion Detection
Privacy Masking
SPECO DNR
Digital Zoom
DIS (Digital Image Stabilization)
Sharpness
Flip / Mirror
Power Supply
Power Consumption
Lens
RS485(Option)
Operational Temp.
Storage Temp.
Dimension
Weight
Download from Www.Somanuals.com. All Manuals Search And Download.
650 Line Intensifier3
(Weatherproof Color Dome Camera)
Focus free AI Motorized zoom Lens(2.8-10mm)
Focus Free
HT7248FFI
■
SPECIFICATIONS
MODEL
HT7248FFI
1/3” Sony Super HAD ll CCD
NTSC, PAL
NTSC=811(H) * 508(V) / PAL=795(H) * 596(V)
NTSC=768(H) * 494(V) / PAL=752(H) * 582(V)
NTSC=15.734KHz(H) & 59.94Hz(V) / PAL=15.625KHz(H) & 50.00Hz(V)
2:1 Interlace
Internal
650TV Lines
CDS OFF: 0.15 Lux, CDS ON: 0.00002 Lux
More than 52dB
CVBS: 1.0Vp-p / 75Ω
NTSC=(1/60sec~1/120,000sec) / PAL=(1/50sec~1/120,000sec)
Available
On / Off (Level adjustable)
BLC / HLC / OFF
Color / BW / AUTO
Low / High / Off
ATW / Outdoor / Indoor / Manual / AWC (1,700°K ~ 11,000°K)
Auto / Off (Selectable x2 ~ x512)
On / Off (8 Programmable Zones)
On / Off (12 Programmable Zones)
On / Off (Level adjustable)
On / Off (x1 ~ x16)
On / Off
On / Off (Level adjustable)
On / Off
Image Pick-Up Device
TV System
Total Pixels
Effective Pixels
Scanning Frequency
Scanning System
Synchronization
Resolution
Minimum Illumination
S/N Ratio
Video Output
Electronic Shutter Speed
OSD
WDR
BLC
Day & Night
Gain Control
White Balance
Intensify
Motion Detection
Privacy Masking
SPECO DNR
Digital Zoom
DIS (Digital Image Stabilization)
Sharpness
Flip / Mirror
DC 12V / AC24V(Dual Voltage)
DC 12V 250mA / AC24V 100mA
Focus free AI Motorized zoom Lens(2.8-10mm)
PELCO-D, PELCO-P, BOSCH, HONEYWELL, VICON, PANA, STW(SPD)
14~122ºF RH 95% Max
-4~140ºF RH 95% Max
Power Supply
Power Consumption
Lens
RS485(Option)
Operational Temp.
Storage Temp.
Dimension
5.1" Dia * 3.1"H
1 lb
Weight
6
Download from Www.Somanuals.com. All Manuals Search And Download.
CAMERA INSTALLATION
jvuulj{Gwv~lyGjhislG
XUG~oluG|zpunGXYG}vs{zGkjGOŠ–•š›ˆ•›G–“›ˆŽŒG\WWG”hPG
w–žŒ™Gp•—œ›Gaylk
jŒ•›Œ™GaGORP
kjGXY}Gw–žŒ™Gzœ——“
YUG~oluG|zpunGY[G}vs{zGhjGO[WG}–“›Gh”—šP
ylkORP
hjGY[}
ishjraOTP
w–žŒ™Gzœ——“
ZUGjvuulj{G}pklvGjhislG
T jvuulj{GiujGjhislG{vG{olGiujGqhjrUG
[UGjvuulj{Gh“ˆ™”G–œ›—œ›GOyŒ“ˆ G–œ›—œ›P
T j–••ŒŠ›GORGSGjvtPG–™Gw–š›ŒGˆŠ›ˆ›–•Gˆ•‹GOTUGjvtPG–™G
uŒŽˆ›ŒGˆŠ›ˆ›–•G–GlŸ›Œ™•ˆ“Gh“ˆ™”GkŒŠŒGžŒ•Gt–›–•G
kŒ›ŒŠ›–•GšG˄vu˅G•G›ŒGŠˆ”Œ™ˆU
R
w–š›ŒGh“ˆ™”GkŒŠŒG
jvtG
uŒŽˆ›ŒGh“ˆ™”GkŒŠŒ
T
h“ˆ™”Gvœ›—œ›G
\UGjvuulj{GyzT[_\GjhislG
T j–••ŒŠ›GY~™ŒGjˆ‰“ŒG›–G›ŒG[_\G—–™›GˆšG‰Œ“–žU
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
◑
◑
◑
◑
◑
1
2
Contents
Safety Instructions
FEATURES
3
4
FEATURES
5
Camera Menu Set Up
1. Preset Mode
5
5
2. Menu Set Up
5
3. Lens Setting
6
4. Exposure Setting
5. White Balance Setting
6. WDR Setting
7
8
9
7. Backlight Setting
8. SPECO DNR Setting
9. Day/Night Setting
10. Special Setting
11. RETURN Setting
Trouble Shooting
10
11
12
16
17
◑
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
Precautions for use
◑
◑
◑
◑
◑
◑
This camera should be installed by qualified personnel only
There are no user serviceable parts inside
Do not disassemble this camera other than to make initial adjustments
Use a UL approved regulated 24 volt AC or 12 volt DC power supply
Use appropriate low voltage power cable to prevent fire or electrical shock
Please insure that your installation area can support the weight of the camera
Please handle this camera carefully :
◑
Do not use a strong or abrasive detergent when cleaning the camera
◑
Do not install near cooling or heating device
2
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
Now with “PRESETS”
PRESETS (Outdoor, Indoor, Elevator, Lobby, Hallway & Low Light)
Used for a quick and easy setup for the installation environment.
650TVL Resolution
Horizontal resolution of 650 TV lines is achieved by using a
SONY Super-HAD CCD with 410,000 pixels, and a custom DSP
yielding pictures with a high S/N ratio.
INTENSIFIER 3
More Powerful Performance in low light condition.
High quality Pictures to be captured in very low light condition.
WDR
More Powerful WDR in strong back lighting.
Your camera allows you to get a clear image.
SPECO DNR
The Intensifier camera has a DSP chip that can remove image
noise efficiently showing clean images in low light conditions.
HLC (High Light Compensation)
This function reverses bright spots in the picture (such as
headlights). This enables the entire system to do a better job of
resolving and displaying grayscale information such as a
license plate.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
Motion Detection with Alarm Output
Built in motion detector with adjustable areas of coverage will
Send a signal to an external alarm device when motion is detected.
PRIVACY MASK
It also has the ability to mask up to 8 areas of the picture where
Viewing is not desired. Each zone can be independently
programmed via the OSD
STABILIZER
This function removes image jitter that is caused by vibrations in
the building and reduces the amount of hard drive space.
DIGITAL ZOOM
The picture could be enlarged by this function in digital.
DAY/NIGHT
The Intensifier camera can show color pictures in all lighting
conditions, or you can have it automatically switch to a B/W
picture in low light conditions
OSD
All camera functions are menu driven for easy use.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
●
Preset Mode
SPECO TECH
1.PRESET MODE INDOOR
2.MAIN SETUP
3.EXIT
RESET
1. Preset : INDOOR / OUTDOOR / LOW LIGHT / HALLWAY / LOBBY / ELEVATOR.
- Used for a quick and easy setup for the installation environment.
●
Menu Setup
1. Press the Function Setup switch.
- Main setup menu is displayed on the monitor screen.
MAIN SETUP
1.LENS
DC
2.EXPOSURE
3.WHITE BAL
4.WDR
5.BACKLIGHT
6.SPECO DNR
7.DAY/NIGHT
8.SPECIAL
9.RETURN
ATW
OFF
OFF
ON
AUTO
SAVE
2. Select a desired function using the Function Setup switch.
- Place the cursor over a desired item.
3. Set up a selected item by using the Function Setup switch.
4. To finish the setting, select 'RETURN' and press the Function Setup switch.
NOTE
☞
■ An item with the
icon also has sub menus. To select a sub menu, select an item
◀
with the icon and press the Function Setup switch.
■ An item with the - - - icon is unavailable due to function settings.
●
Lens Setting
Using this function, you can control the screen brightness.
1. When the SETUP menu screen is displayed, select 'LENS' by using
the Function Setup switch so that the arrow indicates 'LENS'.
2. DC : You can adjust the minimum shutter and maximum value of ESC
shutter mode.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
MAIN SETUP
1.LENS
DC
2.EXPOSURE
3.WHITE BAL
ATW
3. THE Lens mode has sub menu items as listed below.
- BRIGHTNESS : Adjusts the video brightness.
-
FOCUS ADJ : To adjust the DC lens focus correctly, you must activate the
Focus Settings mode under each lens menu. Activate the Focus Settings
mode, adjust the lens focus, and then deactivate the settings mode.
NOTE
☞
■ If color rolling occurs when using a DC lens, set Shutter to Fixed (---).
●
Exposure Setting
MAIN SETUP
1.LENS
DC
2.EXPOSURE
3.WHITE BAL
ATW
1. When the SETUP menu screen is displayed, select 'EXPOSURE' by
using the Function Setup Switch.
2. Select a desired mode using the Function Setup switch.
EXPOSURE SETUP
1.BRIGHTNESS
2.SHUTTER
3.AGC
4.INTENSIFY
5.RETURN
25
- - -
HIGH
OFF
◆ SHUTTER : You can select either auto or manual shutter.
* --- : Shutter speed is fixed at 1/60sec(1/50sec)
* ESC : Select this to control the shutter speed automatically. If ESC is
selected, the shutter speed is automatically controlled depending
on the ambient illumination of the subject.
* MANUAL : You can control shutter speed manually.
(NTSC MODEL : 1/60~1/120,000, PAL MODEL : 1/50~1/120,000)
* A.FLK : Select this when you see picture flicker, this can happen when the
frequency of the local lighting clashes with the camera.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE
☞
■ When the SHUTTER is set to MANUAL or A.FLK mode, INTENSIFY will be disabled.
◆
AGC(AUTO GAIN CONTROL) : The higher the gain level, the brighter the screen
- but the higher the noise.
* OFF : Deactivates the AGC function.
* LOW : Allows automatic gain control from 5.3dB to 32dB.
* HIGH : Allows automatic gain control from 5.3dB to 37dB.
◆
INTENSIFY : When it is night or dark, the camera automatically detects the
light level and maintains a clear picture if this mode is activated.
* OFF : Deactivates the INTENSIFY function.
* AUTO : Activates the INTENSIFY function.
◆
RETURN : Select this to save the changes in the EXPOSURE menu and return
to the SETUP menu.
NOTE
☞
■ If you press the Function Setup switch to ‘AUTO’ mode, you can adjust brightness by
increasing or decreasing the shutter speed. (x2 ~ x512)
■ Note that the higher the zoom level, the brighter the screen, but the more likely there
will be a ghosting effect.
■ It is normal for Noise, Spots and Whitish symptoms to appear in INTENSIFY mode
when the D-ZOOM level is increased.
●
White Balance (White Bal) Setting
Use the White Balance function to adjust the screen color.
1. When the SETUP menu screen is displayed, select 'White Bal' by using the
Function Setup switch so that the arrow indicates 'White Bal'.
2. Select a desired mode using the Function Setup switch.
MAIN SETUP
1.LENS
DC
2.EXPOSURE
3.WHITE BAL
ATW
7
Download from Www.Somanuals.com. All Manuals Search And Download.
※ Select one of the following 5 modes, as appropriate for your purpose.
◆
◆
ATW : Select this when the color temperature is between 1,700˚K and 11,000˚K.
OUTDOOR : Select this when the color temperature is between 1,700˚K and 11,000˚K.
(sodium light inclusion)
◆
◆
INDOOR : Select this when the color temperature is between 4,500˚K and 8,500˚K.
MANUAL : Select this to fine-tune White Balance manually. Set White Balance first
by using the ATW or AWC mode. After that switch to MANUAL mode,
fine-tune the White Balance and then press the Function Setup switch.
AWC→SET : To find the optimal luminance level for the current environment, point
the camera towards a sheet of white paper and press the Function
Setup switch. If the environment changes, readjust it.
◆
NOTE
☞
■ White Balance may not work properly under the following conditions. In this case
select the AWC mode.
①
When the color temperature of the environment surrounding the subject is out of the
control range (e.g. clear sky or sunset).
②
When the ambient illumination of the subject is dim.
③
If the camera is directed towards a fluorescent light or is installed in a place where
illumination changes dramatically, the White Balance operation may become unstable.
●
WDR Setting
WDR illuminates darker spots of an image while retaining the same light
level for brighter spots to even out the overall brightness of images with
high contrast between bright and dark spots.
MAIN SETUP
1.LENS
DC
2.EXPOSURE
3.WHITE BAL
4.WDR
ATW
OFF
1. When the SETUP menu screen is displayed, select 'WDR' by using the
switch so that the arrow indicates 'WDR'.
2. Use the switch to change the WDR level according to the contrast
between bright and dark areas.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
●
Backlight Setting
Unlike conventional cameras, the 650Line Intensifier3™ Series are designed to
deliver a distinctive subject and background at the same time, even when the
subject is backlight, by using the features of the proprietary W-V DSP chip.
1. When the SETUP menu screen is displayed, select 'BACKLIGHT' by using
the Function Setup switch so that the arrow indicates 'BACKLIGHT'.
MAIN SETUP
1.LENS
DC
2.EXPOSURE
3.WHITE BAL
4.WDR
5.BACKLIGHT
6.SPECO DNR
7.DAY/NIGHT
8.SPECIAL
9.RETURN
ATW
OFF
OFF
ON
AUTO
SAVE
2. Select a desired mode using the Function Setup switch.
◆
BLC : Enables a user to directly select a desired area from a picture, and to view
the area more clearly.
◆
HLC (High Light Compensation) : If the scene contains extremely bright light areas
such as; from car headlights, the light can mask out much of the on-screen detail
LEVEL : Adjust level of the HLC function.
-
-
-
LIMIT : Enable to change the operating condition.
MASK COLOR/TONE : Change the color / transparency of the masking area.
(Black, Red, Blue, Cyan, Magenta)
-
◆
TOP/BOTTOM/LEFT/RIGHT : Adjust the area to be enhanced
OFF : Not being used
3. Select a desired mode using the Function Setup switch and press the Function Setup switch.
◆
Select 'BLC' to adjust the area to be enhanced then adjust the level.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
BLC SETUP
HLC SETUP
LEVEL
TOP
BOTTOM
LEFT
LOW
38
109
54
LEVEL
LIMITS
MIDDLE
NIGHT ONLY
BLACK
MASK COLOR
MASK TONE
TOP
BOTTOM
LEFT
1
RIGHT
121
5
120
5
Press Set to Return
RIGHT
172
Press Set to Return
☞
10
3. Set the SPECO DNR mode to 'ON' and press the Function Setup switch. Then
you can adjust the noise reduction level.
NOTE
☞
■
■
You cannot set the SPECO DNR to ‘ON’ or ‘OFF’ when the AGC mode of the EXPOSURE menu is ‘OFF’.
When adjusting the noise reduction level in the SPECO DNR mode, remember that the higher
the level set, the more the noise level will be reduced, as will the brightness of the image.
●
Day/Night Setting
You can display pictures in color or black and white.
1. When the SETUP menu screen is displayed, select 'DAY/NIGHT'by using the
Function Setup switch so that the arrow indicates 'DAY/NIGHT'.
MAIN SETUP
1.LENS
DC
2.EXPOSURE
3.WHITE BAL
4.WDR
5.BACKLIGHT
6.SPECO DNR
7.DAY/NIGHT
8.SPECIAL
9.RETURN
ATW
OFF
OFF
ON
AUTO
SAVE
2. Select a desired mode using the Function Setup Switch according to the
picture display you want.
◆
◆
COLOR : The picture is always displayed in color.
B/W : The picture is always displayed in black and white.
- BURST MODE : You can turn on or off the burst
signal on B/W mode.
B/W MODE SETUP
1.BURST MODE
2.RETURN
OFF
11
Download from Www.Somanuals.com. All Manuals Search And Download.
◆
AUTO : The mode is switched to 'Color' in a normal environment, but switches to
'B/W' mode when ambient illumination is low. To set up the switching time for AUTO
mode, press the Function Setup switch. You can turn on or off the burst signal on B/W
mode.
AUTO SETUP
- BURST MODE : You can turn on or off the burst signal
1.BURST MODE
2.COLOR→B/W
DURATION
DWELL TIME
3.B/W→COLOR
DURATION
ON
on B/W mode.
FAST
3SEC
- DURATION : You can select brightness of illumination
about changing the day/night mode.
- DWELLTIME : You can select the duration time about
changing the day/night mode.
FAST
10SEC
DWELL TIME
4.RETURN
→3s, 5s, 7s, 10s, 15s, 20s, 30s, 40, 60s
COLOR→B/W B/W→COLOR
FAST
SLOW
2.5 lux
1 lux
5 lux
10 lux
* The day/night switching point of the
camera can be adjusted.
NOTE
☞
■
When AGC in the EXPOSURE menu is 'OFF', '---' mode operates as like selecting 'COLOR'
mode and 'AUTO' mode can not be selected.
●
Special Setting
1. When the SETUP menu screen is displayed, select 'SPECIAL' by using the
Function Setup switch so that the arrow indicates 'SPECIAL'.
MAIN SETUP
1.LENS
DC
2.EXPOSURE
3.WHITE BAL
4.WDR
5.BACKLIGHT
6.SPECO DNR
7.DAY/NIGHT
8.SPECIAL
9.RETURN
ATW
OFF
OFF
ON
AUTO
SAVE
12
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Select a desired mode using the Function Setup switch.
SPECIAL
1.IMAGE ADJ
2.MONITOR
3.CAM TITLE
4.SYNC
OFF
INT
5.MOTION DET
6.PRIVACY
7.COMM ADJ
8.LANGUAGE
9.RETURN
OFF
OFF
ENGLISH
◆
IMAGE ADJ. :
1) When the SETUP menu screen is displayed, select 'IMAGE ADJ' by
using the Function Setup switch so that the arrow indicates 'IMAGE ADJ'.
2) Select a desired mode using the Function Setup switch.
IMAGE SETUP
1.V-REV
2.H-REV
3.D-ZOOM
4.DIS
OFF
OFF
5.FONT COLOR
6.SHARPNESS
7.RETURN
WHITE
ON
* V-REV : You can flip the picture vertically on the screen.
* H-REV : You can flip the picture horizontally on the screen.
* D-ZOOM : You can use a digital zoom of x1 ~ x16.
* DIS (Digital Image Stabilizer)
:
This function mitigates any picture movement due
to external factors such as wind.
*
FONT COLOR : You can change the OSD font color. (White, Yellow, Green, Red, Blue)
* SHARPNESS : As you increase this value, the picture outline becomes stronger and clearer.
Adjust this value appropriately depending on the sharpness of the picture.
* RETURN : Select this to save the settings for the IMAGE ADJ menu and to return to the SETUP menu.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE
☞
■
■
When the V-REV or H-REV mode is enabled, the text on the screen does not flip.
If you increase the SHARPNESS level too high, the picture may become distorted or noise
may appear.
◆
MONITOR : Please change the settings value of video appropriate to your monitor.
1) LCD : Please select this menu item when using a LCD monitor.
2) CRT : Please select this menu item when using a CRT monitor.
3) USER : Please use this menu item when using a monitor other than standard ones. You can
change the gamma, PED level, and color gain in the sub menus.
◆
CAM TITLE : If you enter a title, the title will appear on the monitor.
1) If the SPECIAL menu screen is displayed, use the Function Setup switch so that the
arrow indicates 'CAM TITLE'.
CAMERA TITLE SETUP
2) Set it to 'ON' by using the Function Setup switch.
A B C D E F G H I J K L M
3) Press the Function Setup switch.
N O P Q R S T U V W X Y Z
a b c d e f g h i j k l m
n o p q r s t u v w x y z
- . 0 1 2 3 4 5 6 7 8 9
4) Use the Function Setup switch to move to a
desired letter and select the letter by pressing
the Function Setup switch. Repeat this to enter
multiple letters. You can enter up to 15 letters.
5) Enter a title, move the cursor to 'POS' and
press the Function Setup switch. The entered
title appears on the screen. Select the position
to display the title on the screen by using the
Function Setup switch and press the Function
Setup switch. When the position is determined,
select 'END' and press the Function Setup switch
to return to the SPECIAL menu.
←→CLR
POS
END
SHOP
NOTE
☞
■
When the CAM TITLE menu is ‘OFF’, no title will be displayed on the monitor screen even if
you enter one.
■
■
Only English is available in this mode.
If you move the cursor to CLR and press the Function Setup switch, all the letters are
deleted. To edit a letter, change the cursor to the bottom left arrow and press the Function
Setup switch. Move the cursor over the letter to be edited, move the cursor to the letter to be
inserted and then press the Function Setup switch.
◆
SYNC : In areas where the supply is at 60Hz(NTSC), 50Hz(PAL), you can synchronize
the output phase of multiple cameras using the power synchronization function
(Line-Lock) without using a synchronization signal generator.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
- INT : Internal Synchronization Type
- L/L : Power Synchronization Type, Line-lock
* Press the Function Setup switch.
* You can select a desired phase from 0 to 359 when select 'phase'.
NOTE
☞
■
When using AC power at 60Hz(NTSC), 50Hz(PAL), frequency, you can use the L/L type
synchronization.
■
When the power is DC 12V, the SYNC menu is fixed to the ‘INT’ mode.
◆
MOTION DET :This product has a feature
MOTION DET
1.SENSITIVITY
2.AREA MODE
3.SEL POS
4.XPOS
5.YPOS
6.FILL → SET
7.RETRUN
that allows you to observe movement of
objects in 8 different areas on the screen,
and the words 'MOTION DETECTED' appear
on the screen when movement is detected.
Activity can be monitor more efficiently.
1) When the SPECIAL menu screen is displayed,
press the Function Setup switch so that the arrow
indicates‘MOTION DET’.
AREA1
ON
L-TOP
3
5
2) Set up the mode using the Function Setup switch.
- SENSITIVITY : You can select up to 8 MD areas. When SENSITIVITY number is high, motion
detection sensitivity is increased to recognize even small movement.
- AREA MODE : Determines whether to use the MD area selected in SENSITIVITY.
- SEL POS : Determines which of the 4 vertices of each MD area is to be used.
- XPOS : Determines the coordinate of the horizontal axis for SEL POS.
- YPOS : Determines the coordinate of the vertical axis for SEL POS.
- FILL→SET : Fills in a selected MD area. The color of the area can be selected from brown,
orange, blue, cyan, green, yellow, magenta and red.
-
RETURN : Select this to save the MOTION DET menu settings and return to the SPECIAL menu.
◆
PRIVACY : Mask an area you want to hide on the screen.
PRIVACY AREA SETUP
1.AREA
2.MODE
3.MASK COLOR
4.MASK TONE
5.TOP
AREA1
OFF
GREEN
1
39
6.BOTTOM
7.LEFT
79
13
8.RIGHT
52
9.RETURN
15
Download from Www.Somanuals.com. All Manuals Search And Download.
1) When the SPECIAL menu screen is displayed, press the Function
Setup switch so that the arrow indicates 'PRIVACY'.
2) Set up the mode using the Function Setup switch.
- AREA : You can select up to 12 PRIVACY areas.
- MODE : Determines whether to use the area selected in the AREA.
- MASK COLOR : Determine area color. You can select Green, Red, Blue, Black, White, Gray.
- MASK TONE : Adjust the brightness of MASK COLOR.
- TOP/BOTTOM/LEFT/RIGHT :Adjust the size and position of the selected area.
- RETURN : Select this to save the PRIVACY menu settings and return to the SPECIAL menu.
◆
COMM ADJ
COMM ADJ
1.CAM ID
1
2400
8-N-1
2.BAUD RATE
3.UART MODE
4.RET PKT
ENABLE
OFF
5.DISP ID
6.PROTOCOL
7.RETURN
PELCO-D
- CAM ID : 1~255
- BAUD RATE : 2400, 4800, 9600, 19200, 38400, 57600
- UART MODE : 8-N-1, 8-E-1, 8-O-1
- RET PKT : ENABLE, DISABLE
- DISP ID : OFF, ON
- PROTOCOL : PELCO-D, PELCO-P, BOSCH, HONEYWELL, VICON, PANA, STW(SPD)
- RETURN
●
RETURN Setting
Select a desired RETURN mode using the Function Setup Switch.
- SAVE : Save the current settings and RETURN the MAIN SETUP menu.
-
NOT SAVE : Do not save the current settings and RETURN the MAIN SETUP menu.
- RESET : Resets the camera settings to the factory defaults. Language,
Communication and Monitor Settings are not initialized.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
●
Trouble Shooting
PROBLEM
POSSIBLE CAUSE
☞
Check the power cable, power supply output and video
Northing appears on
connection between the camera and monitor.
the screen.
☞
Are the camera lens or the lens glass dirty?
Clean the lens / glass with a soft clean cloth.
Adjust the monitor controls, as required.
If the camera is facing a very strong light, change
the camera position.
The image on the
screen is dim.
☞
☞
☞
Adjust the lens focus.
☞
☞
Adjust the contrast control of the monitor.
The image on the
screen is dark.
If there is an intermediate device, correctly set the 75Ω/Hi-z.
The camera is not
working properly
and the surface of
the camera is hot.
☞
Check the camera is correctly connected to an appropriate
regulated power source.
☞
☞
Has MOTION DET been set to ON in the menu?
Motion Detection
is not activated.
Has MD AREA been properly defined?
The color of the
☞
☞
Check the settings in WHITE BALANCE menu.
picture is not correct.
The image on the
Make sure that the camera isn’t facing direct sunlight or
screen flickers.
fluorescent lighting. If necessary,change the camera position.
☞
☞
Check that the AGC setting in the EXPOSURE menu is’t set to OFF.
Check the EXPOSURE menu and make sure SHUTTER is set to------.
The INTENSIFY does
not work.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT WARRANTIES AND INFORMATION EFFECTIVE JULY 8, 2008
POLICY, TERMS AND CONDITIONS OF SALE
This statement of policy is in lieu of any other policy, expressed or implied, and no representative or person is authorized to assume for us any
other liability or policy without our written consent. We cannot be held responsible for typographical errors.
TERMS OF PAYMENT
2%, 10 days, net 30 from invoice date of merchandise for qualified accounts or Visa/MasterCard/Amex net at time of order placement only,
other payment discounts do not apply ($300 credit card minimum). We reserve the right to charge 1-1/2% interest per month on past
due balances. New orders will not be shipped while there is a past due balance. We will also ship net C.O.D. or C.I.A.
PRICING POLICY
This price sheet reflects current published price. All prices are subject to change without notice. All items will be billed at current prices.
CREDIT
Companies that have not established credit with our company should allow a sufficient period of time for credit approval. Please be sure to
provide complete credit information, bank and trade references, plus financial statements, if available with your first order. To expedite first
shipment, a certified or bank check with the order or use of Visa/MasterCard/Amex will avoid delays, while we are checking credit and waiting
for bank clearance.
FREIGHT POLICY
All shipments are F.O.B. our New York warehouse. All orders totaling $2000 or more will be shipped freight allowed to any point in zones 1,2,3,4,5
and 1/2 freight allowed in zones 6,7,8, providing invoice is paid within 30 days from receipt of merchandise, catalogs or exceptions from regular
pricing. All UPS and USPS shipments will be insured with insurance fee plus shipping and handling charges added to the invoice.
MINIMUM OPENING ORDER $1500
We reserve the right to refuse reorders under $250. PLEASE REQUEST CONFIRMATION OF ALL FAXED PURCHASE ORDERS.
WARRANTY
We warranty all products to be free from any manufacturing or material defects.
Cameras
5 Years
1 Year
3 Years
2 Years
Lifetime
5 Years
This warranty will not extend to any products which have been subjected to misuse,
neglect, accident, or improper installation, used in violation of instructions furnished by
us; or to units which have been repaired or altered outside of the factory. This limited
warranty does not apply to broken cases, batteries, or other physically damaged parts.
Upon request by the customer, the company will at the customer's expense repackage
merchandise in new cartons, replace missing accessories, and return in resalable
condition. Unless requested, the company will replace and return all merchandise in the
packaging in which it was received. This warranty is in lieu of all expressed warranties,
expressed or implied, and of all obligations or liability on our part, and we
neither assume nor authorize any representative or other person to assume for us any
obligation or liability. In no event shall we be liable for incidental or consequential
damages arising from the use of the product, or for any delay in the use of this product
do to causes beyond our control. Some states do not allow limitations of how long an
implied warranty lasts and/or do not allow the exclusion or limitation of consequential
damages. The above limitations on implied warranty and consequential damages may
not apply to you. This warranty gives you specific legal rights. You may have other
rights which vary from state to state. See actual warranty statement included with
product for limitations and exclusions where applicable. This limited warranty extends to
products listed in the company's current price schedule.
Monitors & IR LEDs
DVRs / EZVR Series VDRs
PCPro / PCL Series DVRs
Indoor Speakers
Outdoor/Weatherproof Speakers
Amplifiers
5 Years
2 Years
PA Horns, Microphones,
Volume Controls
Megaphones,
Speaker Distribution Centers
and Speaker Selectors
1 Year
Electrical Equipment Not Listed
Above & Balance of Line
90 Days
RETURNS
A written return authorization must be obtained prior to shipment. Label(s) must appear on all packages and return must be ship prepaid.
Defective in-warranty products will be returned prepaid. Defective out-of-warranty products will be repaired at a nominal charge for parts and
labor and returned with shipping charges added to the invoice. If you require an estimate before repair, please request.
RETURNED GOODS POLICY
1. RETURNS SENT WITHOUT PRIOR APPROVAL WILL NOT BE ACCEPTED. CREDIT WILL BE ISSUED UPON INSPECTION OF RETURNED UNITS.
2. No discounted item may be returned for credit or exchange.
3. An order of $3.00 for every $1.00 to be returned must accompany a request for return for stock adjustment.
4. There will be a minimum charge of 15% for handling and repacking where necessary. Merchandise returned for credit or exchange with
missing or damaged packaging or accessories will be charged accordingly. Merchandise returned for repair will be shipped back repaired
but in the same physical condition as when received by us. If repacking or refurbishing is requested, where possible, you will be charged
accordingly.
5. If a credit is issued, current best quantity price or price when purchased, whichever is lower, will prevail.
BACK ORDERS
Products not immediately available for shipment will be back ordered and shipped as soon as available, unless we are advised to cancel back
orders. The original order will determine basis of shipment. If the original order is freight allowed, back orders will be freight allowed. If the
original order does not qualify for freight allowance, back orders will be shipped freight collect or shipping and handling charges added to
the invoice.
PROMOTIONAL MATERIAL
Requests for nominal amounts of catalogs, brochures, promotional sheets, etc. will be supplied at no charge. Requests for bulk quantities of
promotional materials will be billed on a cooperative 50-50 basis.
CLAIMS
Claims for shortage must be presented within thirty days of date of invoice. Freight damage claims and freight shortages should be filed
directly with the carrier within seven days of receipt of shipment. No liability will be accepted for damages directly or indirectly caused from
the use of our products or from any other cause. Our liability shall be limited to the repair and/or replacement of our products, at our option
of found to be defective.
NOTE: All units priced and packaged individually unless specified. Not responsible for printer errors.
We now accept Visa/MasterCard/AMEX at time of order placement. (See terms of Payment & Credit Terms)
For more information contact us at: Speco Technologies 200 New Highway • P.O. Box 726 • Amityville, N.Y. 11701-0726
Tel. 631-957-8700 Outside Metro N.Y. 1-800-645-5516 • Fax 631-957-9142 or 631-957-3880 • Web: www.specotech.com
18
Download from Www.Somanuals.com. All Manuals Search And Download.
▶
MEMO
19
Download from Www.Somanuals.com. All Manuals Search And Download.
▶
MEMO
20
Download from Www.Somanuals.com. All Manuals Search And Download.
200 New Highway
Amityville, NY 11701
631-957-8700
1 800 645 5516
Download from Www.Somanuals.com. All Manuals Search And Download.
|