Sony MiniDisc Player MDX C6500R User Manual
MDX-C6400R/C6500R/C6500RX  
SERVICE MANUAL  
AEP Model  
MDX-C6400R/C6500R/C6500RX  
Ver 1.2 2001.12  
UK Model  
MDX-C6500R/C6500RX  
Photo: MDX-C6500R  
Model Name Using Similar Mechanism  
NEW  
Base Mechanism Type  
Optical Pick-up Name  
MG-164NZ-138  
KMS-241C  
SPECIFICATIONS  
MD p la ye r se ct io n  
Ge n e ra l  
Outputs  
Audio outputs*1  
Power aerial relay control  
lead  
Signal-to-noise ratio  
Frequency response  
Wow and flutter  
90 dB  
10 – 20,000 Hz  
Below measurable limit  
Power amplifier control  
lead  
Tu n e r se ct io n  
Telephone ATT control  
lead*2  
FM  
Tone controls  
Bass ±9 dB at 100 Hz  
Treble ±9 dB at 10 kHz  
12 V DC car battery  
(negative ground)  
Approx. 178 × 50 × 183 mm  
(w/h/d)  
Tuning range  
Aerial terminal  
87.5 – 108.0 MHz  
External aerial connector  
Power requirements  
Dimensions  
Intermediate frequency 10.7 MHz/450 kHz  
Usable sensitivity  
Selectivity  
Signal-to-noise ratio  
8 dBf  
75 dB at 400 kHz  
66 dB (stereo),  
72 dB (mono)  
Mounting dimensions  
Approx. 182 × 53 × 162 mm  
(w/h/d)  
Harmonic distortion at 1 kHz  
0.6 % (stereo),  
Mass  
Supplied accessories  
Approx. 1.2 kg  
Parts for installation and  
connections (1 set)  
Front panel case (1)  
0.3 % (mono)  
35 dB at 1 kHz  
30 – 15,000 Hz  
Separation  
Frequency response  
1
*
Equipped with front and rear outputs:  
MDX-C6500RX/C6500R only  
Equipped with rear outputs: MDX-C6400R  
MDX-C6500RX/C6500R only  
MW/LW  
Tuning range  
MW: 531 – 1,602 kHz  
LW: 153 – 279 kHz  
2
*
Aerial terminal  
External aerial connector  
Intermediate frequency 10.7 MHz/450 kHz  
U.S. and foreign patents licensed from Dolby  
laboratories Licensing Corporation.  
Sensitivity  
MW: 30 µV  
LW: 40 µV  
Design and specifications are subject to change  
without notice.  
Po w e r a m p lifie r se ct io n  
Outputs  
Speaker outputs  
(sure seal connectors)  
4 – 8 ohms  
Speaker impedance  
Maximum power output 50 W × 4 (at 4 ohms)  
FM/MW/LW MINIDISC PLAYER  
9-870-051-13  
2001L0500-1  
C 2001.12  
Sony Corporation  
e Vehicle Company  
Published by Sony Engineering Corporation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION 1  
GENERAL  
This section is extracted from  
instruction manual.  
Location of controls  
Setting the clock  
The clock uses a 24-hour digital indication.  
Example: To set the clock to 10:08  
1
Press (MENU), then press either side of  
(DISC/PRST) repeatedly until “CLOCK”  
appears.  
OPEN  
PTY  
DSPL  
D-BASS  
TA  
MENU  
LIST  
-SEEK/AMS  
SOURCE  
AF  
SOUND  
ENTER  
REP  
1
SHUF  
2
MODE  
3
4
5
6
OFF  
1 Press (ENTER).  
MDX-C6500RX/C6500R  
/C6400R  
The hour indication flashes.  
Refer to the pages listed for details.  
2 Press either side of (DISC/PRST) to set  
the hour.  
1 Volume control dial 19  
qf SEEK/AMS –/+ (cursor left/right) buttons  
8, 10, 12, 14, 16, 18, 19, 21, 23, 24  
Automatic Music Sensor 10, 14  
Manual Search 10  
2 MENU button 8, 10, 12, 13, 14, 15, 16,  
18, 19, 21, 24  
3 DISC/PRST +/– (cursor up/dow n) buttons  
Seek 15, 16, 18  
8, 10, 12, 13, 14, 15, 16, 18, 19, 20, 21, 24  
3 Press the (+) side of (SEEK/AMS).  
qg ENTER button 8, 10, 12, 13, 14, 15, 16,  
During CD/MD playback:  
Disc change 10, 13  
18, 19, 20, 21, 24  
qh MODE button 19  
During radio reception:  
Preset stations select 16  
During CD or MD playback:  
CD/MD unit select 9, 13  
During radio reception:  
BAND select 15, 16  
The minute indication flashes.  
4
Z (eject) button (located on the front  
side of the unit behind the front panel)  
9
4 Press either side of (DISC/PRST) to set  
the minute.  
qj Receptor for the card remote  
5 DSPL/PTY (display mode change/  
programme type) button 9, 10, 12, 17,  
20  
commander  
qk Number buttons  
During radio reception:  
Preset number select 15, 16, 18, 19  
During CD/MD playback:  
(1)REP 11  
(2)SHUF 11  
6 LIST button 12  
List-up 13  
2
Press (ENTER).  
7 SOURCE (TUNER/CD/MD) button  
8, 9, 10, 13, 15, 16, 19  
8 Display w indow  
ql AF button 17, 18, 19  
9 OPEN button 7, 9, 26  
q; D-BASS button 25  
qa SOUND button 23  
w; TA button 18, 19  
The clock starts.  
* Wa rn in g w h e n in st a llin g in a ca r  
w it h o u t ACC (a cce sso ry) p o sit io n o n  
t h e ig n it io n ke y sw it ch  
Be sure to press (OFF) on the unit for tw o  
seconds to turn off the clock display after  
turning off the engine.  
After the clock setting is completed, the  
display returns to normal play mode.  
qs Reset button (located on the front side  
Tip  
of the unit behind the front panel) 7  
You can set the clock automatically with the RDS  
feature (see page 17).  
qd OFF button* 7, 8, 9  
When you press (OFF) only momentarily,  
the clock display does not turn off and this  
causes battery wear.  
Note  
In the initial setting, the clock indication appears  
while the unit is turned off.  
When the D.INFO mode is set to ON, the time is  
always displayed (page 24).  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION 2  
DISASSEMBLY  
Note: Follow the disassembly procedure in the numerical order given.  
SUB PANEL ASS’Y  
1 screw  
(PTT2.6 × 5)  
2 cover  
4 two claws  
5 sub panel ass’y  
3 screw  
(PTT2.6 × 8)  
4 claw  
3 two screws  
(PTT2.6 × 8)  
6 flexible flat cable (CNP811)  
3 screw  
(PTT2.6 × 8)  
MECHANISM DECK (MG-164NZ-138)  
3 two screws  
(PTT2.6 × 5)  
4 bracket (MD)  
5 mechanism deck  
(MG-164NZ-138)  
1 screw  
2 connector  
(CN101)  
(PTT2.6 × 5)  
1 screw  
(PTT2.6 × 5)  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVO BOARD  
2 two screws  
(BVTT2 × 4)  
2 two screws  
(BVTT2 × 4)  
3 servo board  
1 sensor flexible board  
(CN102)  
1 flexible board  
(CN103)  
MAIN BOARD  
1 three ground point  
screws  
2 three screws  
(PTT2.6 × 10)  
3 main board  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MD COVER ASS’Y  
1 four screws  
(B2 × 3)  
3 MD cover ass’y  
shaft (MD cover guide)  
cassette holder  
A
2 Pushing the Cassette Holder in the direction of the arrow A with a  
screwdriver, etc., disengage the Shaft (MD Cover Guide) from  
the slot in the MD Cover Assy.  
Note: Take care not to scratch the optiocal Pick-up when pushing  
the Cassette Holder with a screwdriver. etc.  
HEAT SINK  
2 two screws  
(PTT2.6 × 12)  
1 three screws  
(PTT2.6 × 10)  
1 screw  
(PTT2.6 × 10)  
C6500R/C6500RX  
3 heat sink  
1 two screws  
(PTT2.6 × 10)  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FLOAT BLOCK  
3 Pushing an arrow A part, raise the float block  
up ward at the front to release a lock.  
1 tension spring (FLOAT B)  
A
float block  
lever (lock R)  
lever (lock L)  
1 tension spring (FLOAT B)  
2 two tension springs (FLOAT F)  
LO MOTOR ASS’Y (LOADING) (M903)  
4 Remove the bracket (LO)  
in the direction of the arrow A.  
A
5 LO motor ass’y (loading)  
(M903)  
1 Remove solders of motor (M903)  
2 tension spring (rack)  
3 claw  
bracket (LO)  
– bottom view –  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LEVER (LE) ASS’Y  
2 stopper washer  
2 lever (LE) ass’y  
3 roller (GEAR E)  
1
HOLDER ASS’Y  
4 Remove the holder ass’y in the  
direction of the arrow.  
2 type-E stopring 1.5  
1 spring (CHKG)  
2 type-E stopring 1.5  
2 type-E stopring 1.5  
3 lever (lock R)  
3 lever (lock L)  
2 type-E stopring 1.5  
1 spring (CHKG)  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CHUCKING ARM ASS’Y  
1 Remove the chucking arm ass’y  
in the direction of the arrow.  
holder ass’y  
OPTICAL PICK-UP (KMS-241C/J1NP)  
4 screw  
(B2 × 3)  
6 bearing (SL)  
5 feed screw ass’y  
7 optical pick-up  
(KMS-241C/J1NP)  
3 screw  
(K2 × 3)  
1 two screws  
(K2 × 3)  
2 guide shaft (OPT L)  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SL MOTOR ASS’Y (SLED) (M902), SP MOTOR ASS’Y (SPINDLE) (M901)  
4 screw  
(P1.7 × 1.8)  
9 two screws  
(P1.7 × 1.8)  
5 bracket (SL)  
2 two screws  
(2 × 8)  
6 SL motor ass’y  
(sled) (M902)  
0 bracket (SP)  
7 screw  
3 sensor board  
(B2 × 3)  
qa SP motor ass’y  
8 base (SL)  
(spindle) (M901)  
1 Remove solders of motors  
(M901, M902)  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION 3  
ELECTRICAL ADJUSTMENTS  
TEST MODE  
This set have the test mode function.  
<Set the Test Mode>  
1. Turn ON the regulated power supply. (The clock is displayed)  
Note: Press the [OFF] button, if the clock is not displayed.  
2. Push the preset [4] button.  
3. Push the preset [5] button.  
4. Press the preset [1] button for more than two seconds.  
5. Then the display indicates all lights, the test mode is set.  
<Release the Test mode>  
1. Push the [OFF] button.  
MD SECTION  
MD section adjustments are done automatically in this set.  
TUNER SECTION  
Tuner section adjustments are done automatically in this set.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MDX-C6400R/C6500R/C6500RX  
SECTION 4  
DIAGRAMS  
15  
TX  
IC301 (1/2)  
4-1. BLOCK DIAGRAM – SERVO Section –  
• SIGNAL PATH  
: MD PLAY  
EFMO  
ADDT  
100  
23  
FILI  
DIGITAL SIGNAL PROCESSOR,  
EFM/ACIRC ENCODER/DECODER,  
SHOCK PROOF MEMORY CONTROLLER,  
ATRAC ENCODER/DECODER, 2M BIT D-RAM  
IC301 (1/2)  
59  
58  
61  
60  
PCO  
CLTV  
FILO  
PLL  
SAMPLING  
RATE  
CONVERTER  
RF AMP,  
FOCUS/TRACKING ERROR AMP  
IC302  
DIN  
DOUT  
DIGITAL  
AUDIO  
INTERFACE  
21  
22  
48 47  
ASYO  
51  
(Page 19)  
ASYI  
RFI  
52  
55  
I
I
DADT  
DADT, BCK, LRCK, FS256  
COMPA-  
RATOR  
1
2
RFO  
AGCI  
RF  
24  
A
RF AGC  
& EQ  
RF AMP  
46  
40  
38  
J
J
EQ  
26 25 27  
AUX  
B.P.F.  
33  
WBL  
D-RAM  
X301  
22.5792MHz  
OSCI  
512FS OSC  
IC304  
16  
17  
CLOCK  
GENERATOR  
3T  
TEMP  
PEAK  
F
OSCO  
37  
36  
PEAK &  
B
A
BOTM  
BOTTOM  
WBL  
C
D
B
A
SUBCODE  
PROCESSOR  
INTERNAL BUS  
I
J
ADIP  
DEMODULATOR/  
DECODER  
ADFM  
ADIN  
ADFG  
AT  
AMP  
29  
30  
32  
78  
79  
B.P.F.  
A
B
C
D
4
5
6
7
I-V  
AMP  
ABCD  
FE  
ABCD  
AMP  
E
35  
34  
DETECTOR  
CPU  
INTERFACE  
MONITOR  
CONTROL  
FOCUS  
F0CNT  
SPINDLE  
SERVO  
C
D
ERROR AMP  
TE  
SE  
E
F
E
F
8
9
26  
28  
I-V  
AMP  
TRACKING  
ERROR AMP  
94 93 10 12  
11  
14  
9
8
5
6
7
1
2
3
4
COMMAND  
LASER DIODE  
XOE  
XWE  
XRAS  
XCAS  
41  
45  
44  
42  
22  
3
OE  
5
13  
3
4
1
2
AUTOMATIC  
POWER  
CONTROL  
Q302  
WE  
RAS  
CAS  
SERIAL/  
PARALLEL  
CONVERTER,  
DECODER  
APC  
PD  
ILCC  
LD/PD  
AMP  
LEVEL SHIFT  
IC502  
LEVEL SHIFT  
IC503  
4
11  
10  
V-I  
23  
CONVERTER  
PD  
LD  
6
12  
PD  
D-RAM  
IC307  
12  
20  
16 17 18  
OPTICAL PICK-UP BLOCK  
(KMS-241C)  
+3.3V  
FOCUS/TRACKING COIL DRIVE,  
SPINDLE/SLED MOTOR DRIVE  
IC303  
(Page 19)  
RESET  
RESET, EMPHASIS  
PSB 16  
B
TH501  
ABCD  
PEAK HOLD  
Q301  
SPFD  
SPRD  
+3.3V  
6
8
OUT4F  
OUT4R  
IN4R  
IN4F  
3
4
M901  
IC306  
59  
62  
55  
54 52  
45 51 64  
26 27 28 29  
39  
66  
M
M
(SPINDLE)  
13  
RECP  
66 75 64 65 74 73 62 63  
LOCK  
LOCK  
21  
67  
C
APCREF  
(Page 19)  
AUTOMATIC  
POWER  
CONTROL  
83  
31  
32  
EXTAL  
XTAL  
MD MECHANISM CONTROLLER  
IC501 (1/2)  
MD-ATT  
SFDR  
SRDR  
ANALOG MUX  
X501  
10MHz  
A-MUTE  
56  
D
27 OUT2F  
25 OUT2R  
IN2F 29  
IN2R 30  
92  
91  
M902  
(SLED)  
(Page 19)  
A/D CONVERTER  
DIGITAL  
SERVO  
7
5
6
63  
11  
2-AXIS  
DEVICE  
SIGNAL  
PROCESS  
FROM CPU  
INTERFACE  
FCS+  
FFDR  
FRDR  
21 OUT1F  
23 OUT1R  
IN1F 19  
IN1R 18  
88  
89  
4
XLRF  
CKRF  
DTRF  
80  
81  
82  
LOADING  
MOTOR DRIVE  
IC305  
RIN  
FIN  
(LIMIT)  
AUTO  
SEQUENCER  
LOADING START/  
EJECT END  
LOADING  
END  
ON: When completion of  
the disc loading.  
ON: When the optical pick-up is  
inner position.  
FCS–  
TRK+  
TRK–  
TFDR  
TRDR  
12 OUT3F  
10 OUT3R  
IN3F 14  
IN3R 15  
86  
85  
OUT1 OUT2  
1
ON: When the disc loading start  
and the disc eject completion.  
DIGITAL SERVO  
SIGNAL PROCESSOR  
IC301 (2/2)  
7
M903  
(LOADING)  
05  
M
Download from Www.Somanuals.co1m7. All Manuals1S7earch And Download.  
MDX-C6400R/C6500R/C6500RX  
4-2. BLOCK DIAGRAM – TUNER Section –  
BU B+  
TUNER +8.7V  
TUNER +5.6V  
FM/AM TUNER UNIT  
TU1  
11  
5
16  
J1  
(FM/AM ANTENNA)  
MPX  
AM  
2
1
ANT-FM  
ANT-AM  
MPX 10  
(Page 19)  
(Page 19)  
E
F
MUTING  
Q111  
AM-DET  
8
17 18  
4
14  
9
12 13  
19  
MUTING  
Q121  
MUTING  
CONTROL SWITCH  
Q131  
D131  
IF-AM  
(Page 19)  
(Page 19)  
G
I
DATA, CLOCK  
RDS DECODER  
5
4
IC51  
SIGNAL  
QUALITY  
DECODER  
SC  
OUT  
SDA  
SCL  
57 kHz  
BAND-PASS  
FILTER  
IIC BUS  
SLAVE  
TRANSCEIVER  
RDS/RDBS  
DEMODULATOR  
& DECODER  
CIN  
9
10  
CLOCKED  
INTERFACE  
REGISTER  
16  
20  
18  
19  
COMPARATOR  
MPX  
LVIN  
BUFFER  
Q1  
MULTI  
PATH  
DETECTOR  
OSCILLATOR  
& CLOCK  
2
BAND-PASS  
FILTER  
IC90  
5
4
8
Q90  
NOISE DET  
DISCHARGE  
SWITCH  
X51  
4.332MHz  
S-METER  
(Page 19)  
H
53  
52  
64  
50  
32  
56  
9
10  
51  
MASTER CONTROLLER  
IC501 (1/3)  
• SIGNAL PATH  
: FM  
: MW/LW  
05  
18  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MDX-C6400R/C6500R/C6500RX  
4-3. BLOCK DIAGRAM – MAIN Section –  
(L)  
(R)  
CNJ151 (1/2)  
INPUT SELECT,  
ELECTRICAL VOLUME, FM MPX  
IC151  
BUS  
AUDIO IN  
R-CH  
DADT,  
BCK,  
CNJ151 (2/2)  
(L)  
FD1L  
SEL  
AM  
LOUDNESS/  
VOLUME  
SOFT  
MUTE  
TONE  
LRCK,  
3
1
VOUTL  
VOUTR  
CONTROL  
FS256  
DADT  
BCK  
DATA  
BCK  
OUTLF  
OUTLR  
(Page 17)  
5
6
4
30  
29  
12  
9
MONO  
FADER  
A
B
MIXER  
11  
MUTING  
Q171  
LRCK  
LRCK  
AUDIO OUT  
FRONT  
R-CH  
MUTE  
LOUDNESS  
R-CH  
(R)  
(C6500R, C6500RX)  
MUTING  
Q271  
FS256  
RESET  
XTI  
AMIF  
MPX  
CLK  
CONTROL  
MODE  
AM/FM  
NOISE  
1
12  
13  
AUDIO OUT  
REAR  
CONTROL  
(L)  
(R)  
BLANKER  
RESET,  
EMPHASIS  
DIGITAL FILTER,  
D/A CONVERTER  
IC101  
(C6500R, C6500RX)  
MUTING  
Q181  
RSTB  
(Page 17)  
15  
DEMODULATOR  
+STEREO ADJUST  
+STEREO BLEND  
PILOT  
CANCELATION  
L.P.F.  
L.P.F.  
S & H  
HIGH-CUT  
R-CH  
17 16  
AUDIO OUT  
(C6400R)  
R-CH  
PILOT  
DET  
MUTING  
Q281  
PLL  
EMPHASIS  
D/A  
CONVERTER  
AM  
(Page 18)  
(Page 18)  
(Page 18)  
F
G
E
DIGITAL  
CN601 (1/2)  
(POWER CONNECTOR)  
POWER AMP  
IC611  
CONTROL  
IF-AM  
MPX  
IIC BUS  
1
FL+  
5
3
FRONT L (+)  
12 FL-IN  
9
4
D621  
FL–  
FRONT L (–)  
FRONT R (+)  
FRONT R (–)  
REAR L (+)  
REAR L (–)  
REAR R (+)  
REAR R (–)  
20  
21  
18  
14  
FR+ 21  
14  
11  
FR-IN  
RL-IN  
12  
2
DATA, CLOCK  
DATA  
(Page 18)  
FR– 23  
I
CLOCK  
RL+  
9
7
10  
3
S-METER  
LOCK  
(Page 18)  
(Page 17)  
RL–  
H
C
RR+ 17  
15 RR-IN  
11  
70  
71  
57  
84  
RR– 19  
MASTER CONTROLLER  
IC501 (2/3)  
16  
60  
59  
16  
22  
4
BEEP  
AUX IN  
MUTE  
AMPATT  
AMPON  
STNBY  
48 85  
46  
47  
36  
37  
76  
35  
67  
12  
13 14 15  
93  
92  
73  
74  
58  
79  
81  
15  
13  
TEST  
KEY ACTIVE  
X501  
3.68MHz  
X502  
32.768kHz  
U-COM +5V  
SWITCH  
CN500  
MAIN BODY SIDE  
14  
Q651, 652  
LEVEL SHIFT  
Q571  
TEL-ATT  
D571  
SW504  
(NOSE DETECT)  
(C6500R, C6500RX)  
64 63 62  
CN901  
FRONT PANEL SIDE  
D622  
BATTERY OFF  
MUTE DRIVER  
Q621  
1
J501  
REMOTE IN  
BACK-UP B+  
D501  
LSW810,  
LSW901 – 917,  
S901 – 904  
ROTARY  
ENCODER  
RE901  
LIQUID CRYSTAL  
DISPLAY DRIVER  
IC901  
D502  
60  
OSC  
OSC  
C953, R957  
VOLUME/BASS/TREBLE/  
BALANCE/FADER CONTROL  
–
–
S04 S51  
COM1 COM4  
• SIGNAL PATH  
MUTING  
CONTROL SWITCH  
Q622  
–
–
4
51  
52 55  
D653  
: MD PLAY  
: FM  
D302  
: MW/LW  
LCD901  
LIQUID CRYSTAL DISPLAY  
: BUS AUDIO IN  
MD-ATT  
(Page 17)  
D
05  
Download from Www.Somanuals.co1m9. All Manuals1S9earch And Download.  
MDX-C6400R/C6500R/C6500RX  
4-4. BLOCK DIAGRAM – BUS CONTROL/POWER SUPPLY Section –  
REMOTE CONTROL  
RECEIVER  
CN701  
MASTER CONTROLLER  
IC501 (3/3)  
BUS CONTROL IN  
(FOR SONY BUS)  
IC951  
D708  
CN601 (2/2)  
3
SIRCS BUFFER  
Q704  
(POWER CONNECTOR)  
SIRCS  
24 SIRCS  
D673  
D674  
6
ANT-R  
RESET SIGNAL  
GENERATOR  
IC652  
BU B+  
RSTX  
90  
AMP-R  
5
86 HSTX  
6
8
AMP+B  
ANT+B  
SW503  
RESET  
BACK-UP B+  
POWER AMP  
(IC611) B+  
D301  
REGULATOR  
IC671  
SONY BUS INTERFACE  
IC701  
TUNER +8.7V  
TUNER +5.6V  
11 TU8.7V  
VCC  
7
D2  
2
5
RST  
RST  
RESET  
10 TU5.6V  
2
13  
11  
SYSRST  
RESET  
DATA  
SWITCH  
RDS DECODER  
(IC51) B+  
DATA  
DATA IN  
6
9
8
18 UNISO  
17 UNISI  
COM +8V  
(AUDIO CIRCUIT B+)  
9
5
COM8V  
BU+B  
DATA OUT  
D1  
4
6
CLK IN  
BUS  
CLK  
BU B+  
CLK  
4
1
19 UNICKO  
20 UNICKI  
11  
12  
BUS ON SWITCH  
Q705  
D676  
BUS ON  
OUT  
PULL UP +5V  
ON IN  
BUS ON  
SWITCH  
BUS ON  
3
BUSON  
D677  
4
3
2
U-COM +5V  
PW ON 120  
TUNON  
1
7
BATT  
BU IN  
BATTERY  
SWITCH  
BATT  
77 BUIN  
3
10  
LCD B+  
LCD DRIVER  
(IC901) B+  
D702  
D701  
TH701  
FU601  
16  
LED901-904,  
LED910-915,  
LSW901-917  
REGULATOR  
Q631  
+B  
BATTERY  
DETECT  
Q701  
BACK-UP B+  
REGULATOR  
CONTROL SWITCH  
Q633  
ILLON  
7
D662  
7
ACCESSORY CHECK  
Q661  
ACC IN 82  
ACC  
LED810  
(MD DISC SLOT)  
29  
DOORIND  
REGULATOR  
Q551  
LED810,  
LSW810  
LSW810  
Z
LO- +12V  
LOADING MOTOR  
DRIVER (IC305) B+  
MD MECHANISM CONTROLLER  
IC501 (2/2)  
+12V  
REGULATOR  
Q361  
B+ SWITCH  
Q402, 403  
60  
61  
MD-ON 65  
BU-IN  
BUS-ON  
REGULATOR  
CONTROL SWITCH  
Q363  
10  
MDMON  
30  
RESET  
DRIVER +5V  
MOTOR/COIL DRIVER  
(IC303) B+  
49 UNISI  
48 UNICKIO  
LEVEL SHIFT  
Q706  
50 UNISO  
+3.3V  
REGULATOR  
IC401, Q401  
+5V  
REGULATOR  
Q362  
+3.3V  
46 LINKOFF  
REGULATOR  
CONTROL SWITCH  
Q250  
05  
20  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• Circuit Boards Location  
4-5. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS  
Note on Printed Wiring Board:  
• X : parts extracted from the component side.  
• Y : parts extracted from the conductor side.  
z
Note on Schematic Diagram:  
• All capacitors are in µF unless otherwise noted. pF: µµF  
50 WV or less are not indicated except for electrolytics  
SENSOR board  
•
•
: Through hole.  
and tantalums.  
• All resistors are in Ω and / W or less unless otherwise  
specified.  
1
f
4
: internal component.  
• b : Pattern from the side which enables seeing.  
(The other layers' patterns are not indicated.)  
•
•
%
f
: indicates tolerance.  
: internal component.  
SERVO board  
Caution:  
• C : panel designation.  
SUB board  
Pattern face side: Parts on the pattern face side seen from  
(Conductor Side) the pattern face are indicated.  
Note: The components identified by mark 0 or dotted line  
with mark 0 are critical for safety.  
Parts face side:  
Parts on the parts face side seen from  
Replace only with part number specified.  
(Component Side) the parts face are indicated.  
•
U : B+ Line.  
• Power voltage is dc 14.4V and fed with regulated dc power  
supply from ACC and BATT cords.  
• Voltages are taken with aVOM (Input impedance 10 MΩ).  
Voltage variations may be noted due to normal produc-  
tion tolerances.  
• Waveforms are taken with a oscilloscope.  
Voltage variations may be noted due to normal produc-  
tion tolerances.  
• Circled numbers refer to waveforms.  
• Signal path.  
E
F
f
L
: MD PLAY  
: FM  
: MW/LW  
KEY board  
: BUS AUDIO IN  
MAIN board  
Download from Www.Somanuals.co2m1. All Manuals2S1earch And Download.  
MDX-C6400R/C6500R/C6500RX  
4-6. PRINTED WIRING BOARDS – SERVO Board (Component Side)/SENSOR Board – • See page 21 for Circuit Boards Location.  
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
A
B
C
D
E
F
(LOADING END)  
5
8
4
1
L101  
(COMPONENT SIDE)  
SERVO BOARD  
K
C103  
C105  
M903  
(LOADING)  
IC401  
C11  
A
RED  
BLK  
+
E
B
20  
11  
C109  
D401  
C
M
C403  
R406  
C108  
C352  
Q401  
C306  
R319  
1
4
8
5
IC101  
C304  
IC305  
L102  
(CHASSIS)  
29  
30  
R316  
C305  
R318  
1
10  
FB301  
+
C106  
C107  
R311  
R312  
C104  
11  
R320  
C308  
50  
26  
CN103  
(CHASSIS)  
51  
25  
11  
8
7
8
1
5
R325  
R324  
1
IC304  
4
CN101  
C310  
X301  
IC502  
IC301  
R328  
C311  
R327  
SENSOR FLEXIBLE  
BOARD  
1-654-693- 11  
14  
8
1
7
D501  
K
R308  
1
SENSOR BOARD  
(COMPONENT SIDE)  
RED  
BLK  
R307  
75  
1
M902  
(SLED)  
M
R306  
R304  
R302  
A
76  
100  
R305  
R303  
R301  
M902  
(SPINDLE)  
M
E
C
B
A
R329  
Q301  
IC503  
MAIN BOARD  
CN301  
R330  
1
2
5
IC306  
4
(Page  
27)  
RED  
BLK  
R353  
C343  
R352  
C342  
C315  
14  
1
11  
1
3
(11)  
1-676-656-  
SENSOR BOARD  
(CONDUCTOR SIDE)  
L303  
L304  
R518  
80  
65  
G
H
I
32  
17  
C349  
1
64  
(LIMIT)  
IC303  
R501  
R502  
C336  
1
16  
R503  
L305  
L306  
IC501  
R531  
• Semiconductor  
Location  
C334  
R516  
Ref. No. Location  
R535  
R539  
D401  
D501  
A-15  
E-13  
+
+
C318  
R355  
24  
41  
1
IC101  
IC301  
IC302  
IC303  
IC304  
IC305  
IC306  
IC401  
IC501  
IC502  
IC503  
B-11  
D-8  
K-11  
H-8  
D-10  
B-16  
F-8  
A-14  
H-15  
D-11  
F-11  
C329  
(CHASSIS)  
C319  
25  
40  
48  
37  
OPTICAL  
PICK-UP  
BLOCK  
J
1
36  
C327  
C326  
C325  
X501  
CN102  
(KMS-241C)  
R511  
R532  
IC302  
20  
25  
12  
R347  
R527  
13  
24  
R506  
R528  
R526  
R529  
C321  
R336  
+
(CHASSIS)  
K
R345  
R343  
R340  
R344  
R342  
Q301  
Q302  
Q401  
E-6  
K-10  
B-13  
LOADING START  
EJECT END  
11  
R338  
Q302  
1-675-655-  
11  
(11)  
(11)  
1-676-656-  
05  
22  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MDX-C6400R/C6500R/C6500RX  
4-7. PRINTED WIRING BOARD – SERVO Board (Conductor Side) – • See page 21 for Circuit Boards Location.  
1
2
3
4
5
6
7
8
9
10  
11  
12  
A
B
C
D
E
F
(CONDUCTOR SIDE)  
SERVO BOARD  
+
R402  
R401  
R104  
R202  
R403  
B
E
Q402  
B
C
E
C
+
C361  
Q403  
+
13  
9
5
1
IC307  
C307  
14  
18  
22  
26  
+
C358  
C301  
C356  
C357  
C511  
+
C506  
C505  
C316  
C512  
RB302  
RB301  
+
C351  
R534  
R533  
C504  
C515  
C350  
G
H
I
C514  
C513  
C333  
R519  
C503  
J
RB503  
K
• Semiconductor  
Location  
11  
(11)  
Ref. No. Location  
05  
1-675-655-  
IC307  
C-10  
Q402  
Q403  
B-4  
B-5  
Download from Www.Somanuals.co2m3. All Manuals2S3earch And Download.  
MDX-C6400R/C6500R/C6500RX  
4-8. SCHEMATIC DIAGRAM – SERVO Board (1/2) – • See page 31 for Waveforms. • See page 36 for IC Block Diagrams.  
• Voltages and waveforms are dc with respect to ground  
under no-signal conditions.  
no mark : MD PLAY  
The components identified by mark 0 or dotted  
line with mark 0 are critical for safety.  
Replace only with part number specified.  
: Impossible to measure  
∗
24  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MDX-C6400R/C6500R/C6500RX  
4-9. SCHEMATIC DIAGRAM – SERVO Board (2/2) – • See page 31 for Waveforms. • See page 36 for IC Block Diagram.  
(Page  
29)  
• Voltages and waveforms are dc with respect to ground  
under no-signal conditions.  
no mark : MD PLAY  
: Impossible to measure  
∗
Download from Www.Somanuals.co2m5. All Manuals2S5earch And Download.  
MDX-C6400R/C6500R/C6500RX  
4-10. PRINTED WIRING BOARD – MAIN Board (Component Side) – • See page 21 for Circuit Boards Location.  
• Semiconductor  
Location  
Ref. No. Location  
D1  
E-9  
G-5  
I-7  
D301  
D501  
D502  
D551  
D552  
D553  
D554  
D555  
D556  
D557  
D558  
D559  
D560  
D571  
D603  
D605  
D611  
D612  
D613  
D614  
D615  
D616  
D617  
D618  
D622  
D623  
D624  
D653  
D661  
D662  
D673  
D674  
D701  
D702  
D703  
D704  
D705  
D706  
D708  
D710  
H-7  
J-13  
K-13  
K-13  
J-12  
K-13  
J-12  
K-13  
J-12  
K-13  
J-12  
B-5  
B-4  
B-5  
B-7  
B-7  
C-7  
C-7  
C-7  
C-7  
C-6  
C-6  
D-9  
C-9  
C-9  
I-7  
D-5  
D-5  
C-5  
C-5  
E-5  
C-4  
B-3  
B-2  
B-2  
B-2  
G-7  
D-4  
IC51  
I-12  
G-11  
D-10  
I-5  
IC90  
IC151  
IC501  
IC652  
IC701  
J-3  
C-3  
Q1  
G-11  
E-12  
F-12  
B-11  
B-11  
H-2  
C-11  
C-11  
I-3  
Q111  
Q131  
Q171  
Q181  
Q250  
Q271  
Q281  
Q363  
Q551  
Q571  
Q621  
Q622  
Q633  
Q651  
Q652  
Q661  
Q701  
Q704  
Q705  
Q706  
J-6  
D-5  
C-10  
C-9  
J-2  
I-8  
I-8  
D-5  
D-5  
G-7  
C-4  
D-4  
26  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MDX-C6400R/C6500R/C6500RX  
6
5
4
4-11. PRINTED WIRING BOARD – MAIN Board (Conductor Side) – • See page 21 for Circuit Boards Location.  
9
1
10 11 12  
13 14 15 16  
8
7
2
3
4
5
6
7
8
3
2
1
(FRONT VIEW)  
• Semiconductor  
Location  
Ref. No. Location  
D2  
E-7  
D90  
H-11  
H-11  
G-11  
F-12  
G-7  
I-2  
D91  
D92  
D131  
D302  
D361  
D362  
D561  
D562  
D563  
D564  
D601  
D602  
D604  
D621  
D631  
D671  
D672  
D675  
D676  
D677  
D709  
G-2  
K-11  
K-11  
K-13  
K-12  
C-3  
B-4  
A-5  
B-10  
J-2  
C-5  
C-5  
I-4  
I-4  
I-4  
G-5  
IC611  
IC671  
A-7  
F-1  
Q90  
G-11  
E-12  
H-1  
Q121  
Q361  
Q362  
Q631  
G-1  
J-2  
(Page 32)  
(Page 22)  
Download from Www.Somanuals.co2m7. All Manuals2S7earch And Download.  
MDX-C6400R/C6500R/C6500RX  
4-12. SCHEMATIC DIAGRAM – MAIN Board (1/3) – • See page 31 for Waveform. • See page 36 for IC Block Diagrams.  
(Page 30)  
(Page 29)  
• Voltages and waveforms are dc with respect to ground  
under no-signal (detuned) conditions.  
no mark : FM  
(
[
) : MW  
] : LW  
28  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MDX-C6400R/C6500R/C6500RX  
4-13. SCHEMATIC DIAGRAM – MAIN Board (2/3) – • See page 31 for Waveforms.  
(Page 28)  
(Page  
25)  
(Page  
30)  
• Voltages and waveforms are dc with respect to ground  
under no-signal (detuned) conditions.  
no mark : FM  
(
) : MW  
[
] : LW  
⟨⟨  
⟩⟩ : MD PLAY  
: Impossible to measure  
∗
Download from Www.Somanuals.co2m9. All Manuals2S9earch And Download.  
MDX-C6400R/C6500R/C6500RX  
4-14. SCHEMATIC DIAGRAM – MAIN Board (3/3) – • See page 36 for IC Block Diagrams.  
(Page  
28)  
(Page  
33)  
(Page  
29)  
• Voltages are dc with respect to ground under no-signal  
(detuned) conditions.  
no mark : FM  
⟨⟨  
⟩⟩ : MD PLAY  
30  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• Waveforms  
– SERVO Board –  
– MAIN Board –  
– KEY Board –  
6 IC301 wh (XBCK) (MD Play Mode)  
1 IC101 1 (XTI) (MD Play Mode)  
1 IC51 4 (OSCD)  
1 IC901 y; (OSC)  
qa IC302 1, 2, r;, rh (I, J, AGCI, RFO)  
(MD Play Mode)  
4.4 Vp-p  
2.6 Vp-p  
5 Vp-p  
4.6 Vp-p  
Apporx.  
0.6 Vp-p  
354 ns  
88 ns  
231 ns  
26.4 µs  
2 IC101 4 (LRCK) (MD Play Mode)  
7 IC301 wj (FS256) (MD Play Mode)  
2 IC501 ud (X1A)  
qs IC304 1, 2 (MD Play Mode)  
5.4 Vp-p  
3.8 Vp-p  
4.1 Vp-p  
4.4 Vp-p  
88 ns  
44.3 ns  
30.5 µs  
22.7 µs  
3 IC101 6 (BCK) (MD Play Mode)  
8 IC301 tg (RFI), IC302 ek (RF)  
3 IC501 od (X1A)  
qd IC304 3 (MD Play Mode)  
(MD Play Mode)  
3.4 Vp-p  
3.4 Vp-p  
5.6 Vp-p  
Apporx.  
1.5 Vp-p  
44.3 ns  
354 ns  
272 ns  
4 IC301 qh (OSCI) (MD Play Mode)  
9 IC301 yg (FE), IC302 ef (FE)  
qf IC304 7 (MD Play Mode)  
(MD Play Mode)  
4.4 Vp-p  
4.6 Vp-p  
Approx.  
0.5 Vp-p  
44.3 ns  
44.3 ns  
5 IC301 wg (LRCK) (MD Play Mode)  
0 IC301 uf (TE), IC302 wh (TE)  
qg IC501 ea (EXTAL)  
(MD Play Mode)  
4.4 Vp-p  
3.7 Vp-p  
Approx.  
2 Vp-p  
22.7 µs  
101 ns  
Download from Www.Somanuals.co3m1. All Manuals3S1earch And Download.  
MDX-C6400R/C6500R/C6500RX  
4-15. PRINTED WIRING BOARD – SUB Board – • See page 21 for Circuit Boards Location.  
(Page 27)  
(Page 34)  
32  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MDX-C6400R/C6500R/C6500RX  
4-16. SCHEMATIC DIAGRAM – SUB Board –  
(Page 30)  
(Page 35)  
Download from Www.Somanuals.co3m3. All Manuals3S3earch And Download.  
MDX-C6400R/C6500R/C6500RX  
4-17. PRINTED WIRING BOARD – KEY Board – • See page 21 for Circuit Boards Location.  
• Semiconductor  
Location  
Ref. No. Location  
IC951  
C-5  
LED901  
LED902  
LED903  
LED904  
LED910  
LED911  
LED912  
LED913  
LED914  
LED915  
A-2  
C-2  
C-3  
A-3  
B-12  
B-12  
A-12  
A-5  
B-5  
B-5  
• Semiconductor  
Location  
Ref. No. Location  
D901  
D902  
D903  
D904  
D951  
D952  
A-11  
B-10  
B-10  
B-10  
C-4  
B-6  
IC901  
B-8  
(Page 32)  
34  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MDX-C6400R/C6500R/C6500RX  
4-18. SCHEMATIC DIAGRAM – KEY Board – • See page 31 for Waveform.  
(Page  
33)  
• Voltages and waveforms are dc with respect to ground  
under no-signal (detuned) conditions.  
no mark : FM  
Download from Www.Somanuals.co3m5. All Manuals3S5earch And Download.  
• IC Block Diagrams  
IC302 CXA2523AR  
– SERVO Board –  
IC101 PCM1718E/2K  
48  
47  
46  
45  
44  
43 42  
41  
40  
39  
38 37  
USROP  
–
+
CLK  
CONTROL  
XTI  
DGND  
VDD  
1
2
3
4
5
6
7
8
9
20 XTO  
RF AGC  
EQ  
EQ  
+
–
USRC  
19 CLKO  
18 MUTE  
17 DM1  
RFA1  
INPUT  
DET  
INTERFACE  
BPF3T  
3T  
MODE  
RFA2  
RFA3  
PTGR  
AUX  
SW  
CONTROL  
PEAK3T  
I
1
2
–
DIGITAL  
FILTER  
LRCIN  
DIN  
HLPT  
–1  
1
2
–
–
P-P  
–2  
–
16 DM0  
J
NOISE SHAPER  
3T  
WBL  
OFST  
BCKIN  
ZERO  
D/C_R  
VOUTR  
15 RSTB  
14 FORMAT  
13 D/C_L  
12 VOUTL  
11 VCC  
TEMP  
PEAK  
5 LEVEL  
DAC  
5 LEVEL  
DAC  
–
–
–
1
2
–2  
–1  
CVB  
36  
BOTTOM  
WBL  
BOTM  
+
–
PBH  
VC  
A
3
4
LOWPASS  
FILTER  
LOWPASS  
FILTER  
GRV  
GRVA  
PBSW  
35  
34  
33  
ABCD  
FE  
CMOS  
AMP  
CMOS  
AMP  
AGND 10  
–
–
–
–
+
–
AUX  
AA  
IVR  
IVR  
IVR  
BPFC  
ABCDA  
32 ADFG  
31 ADAGC  
30 ADIN  
+
–
B
C
5
6
BB  
CC  
+
+
–
–
IC301 CXD2652AR  
FEA  
ATA  
+
–
100 99 98 97 96 95 94 93  
92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76  
DET  
BPF22  
–
–
+
+
ADIP  
AGC  
29 ADFM  
28 SE  
WBL  
75  
74  
73  
72  
AUX2  
TE  
PWM  
GENERATOR  
SPINDLE  
SERVO  
+
–
D
E
7
8
MNT0  
MNT1  
MNT2  
MNT3  
1
2
3
4
DD  
EE  
IVR  
IVR  
SE  
MONITOR  
CONTROL  
EACH  
BLOCK  
WBL  
AVSS  
–1  
TG  
TG  
PTGR  
–
+
–
+
–2  
+
–
71  
70  
69  
68  
ADRB  
ADRT  
AVDD  
ADIO  
SEA  
TEA  
+
–
EE'  
ADIP  
DECODER  
27 CSLED  
26 TE  
–1  
–2  
EFB  
TESW  
SWDT  
SCLK  
XLAT  
SRDT  
SENS  
5
6
7
8
9
EBAL  
ESW  
EACH  
BLOCK  
CPU I/F  
67  
66  
65  
64  
63  
62  
VC  
+
–
F
9
SERVO  
DSP  
A/D  
CONVERTER  
AUX1  
FE  
+
–
FF  
IVR  
WBL  
ANALOG  
MUX  
FF'  
25 WBLADJ  
3T  
VI CONV  
ABCD  
BOTM  
PEAK  
IV  
XRST 10  
FBAL  
EQ  
GSW  
SQSY 11  
DQSY 12  
SUBCODE  
PROCESSOR  
PD 10  
AUXSW  
BGR  
COMMAND  
+
–
61  
60  
59  
58  
CLTV  
FILO  
FILI  
RECP 13  
+
–
VREF  
SCRI - PARA  
DECODE  
APC 11  
PCO  
APCREF 12  
SHOCK RESISTANT  
MEMORY CONTROLLER  
XINT 14  
TX 15  
57  
56  
PDO  
13  
14  
15  
16 17 18  
19  
20  
21  
22 23  
24  
AVSS  
OSCI 16  
OSCO 17  
XTSL 18  
NC 19  
CLOCK  
GENERATOR  
EACH  
BLOCK  
55  
54  
53  
52  
51  
RFI  
COMP  
DIGITAL  
AUDIO  
I/F  
SAMPLING  
RATE  
CONVERTER  
BIAS  
AVDD  
ASYI  
ASYO  
DVSS 20  
DIN 21  
DOUT 22  
ADDT 23  
DADT 24  
LRCK 25  
ATRAC  
ENCODER/DECODER  
ADDRESS/DATA BUS A00 - A11, D0 - D3  
26 27 28  
29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49  
50  
36  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IC303 BH6511FS-E2  
32  
31  
30  
29  
28  
27  
26  
25  
24  
23  
22  
21  
20  
19  
18  
17  
AMP  
AMP  
AMP  
AMP  
VDD  
INTERFACE  
INTERFACE  
CHARGE  
PUMP.  
OSC  
PREDRIVE  
PREDRIVE  
PREDRIVE  
PREDRIVE  
AMP  
AMP  
8
AMP  
10  
AMP  
INTERFACE  
INTERFACE  
PSB  
16  
1
2
3
4
5
6
7
9
11  
12  
13  
14  
15  
IC305 BA6287F  
OUT1  
1
2
3
4
8
7
6
5
GND  
VM  
OUT2  
VREF  
RIN  
DRIVER  
DRIVER  
TSD  
VCC  
FIN  
CONTROL LOGIC  
POWER  
SAVE  
IC307 MN41V4400TT-08S  
TIMING  
GENERATOR  
VSS  
26  
TIMING  
GENERATOR  
DQ1  
DQ2  
WE  
RAS  
A9  
1
2
3
4
5
25 DQ4  
DQ3  
24  
23  
22  
CAS  
OE  
WRITE  
CLOCK  
COLUMN  
I/O  
NC  
21  
DECODERS  
SELECTOR  
GENERATOR  
NC  
NC  
NC  
6
7
8
20 NC  
NC  
19  
INTERNAL  
ADDRESS  
COUNTER  
REFRESH  
CONTROL  
CLOCK  
SENSE  
AMPLIFIERS  
A8  
18  
9
10  
11  
A0  
A1  
A2  
17 A7  
16 A6  
A5  
15  
14 A4  
OUTPUT  
BUFFERS  
INPUT  
BUFFERS  
A3 12  
ROW  
DECODERS  
WORD  
DRIVERS  
MEMORY  
CELLS  
DATA BUS  
13  
VCC  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
– MAIN Board –  
IC51 SAA6588T/V2-118  
20  
19  
18  
17  
16  
15  
14  
13  
12 11  
POWER SUPPLY  
& RESET  
PAUSE  
DETECTOR  
MULTI  
PATH  
DETECTOR  
57kHz  
8th ORDER  
BAND-PASS FILTER  
CLOCKED  
COMPARATOR  
SIGNAL QUALITY  
DECODER  
4
5
4
CLOCK  
CLOCK  
DATA  
RDS/RDBS  
DEMODULATOR  
RDS/RDBS  
DECODER  
INTERFACE  
REGISTER  
DATA  
TEST  
CONTROL  
OSCILLATOR  
& CLOCK  
IIC BUS SLAVE  
TRANSCEIVER  
1
2
3
4
5
6
7
8
9
10  
IC671 BA4908-V3  
REGULATOR  
OVER VOLTAGE  
PROTECT  
–
–
–
–
+
+
+
+
2
3
4
5
6
7
8
9
10  
11  
12  
1
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IC151 TDA7402TR  
33 32 31  
30  
29  
28  
27  
26  
25  
24 23  
MIXER  
MONO- MONO-  
FADER FADER  
MONO- MONO-  
FADER FADER  
MONO- MONO-  
FADER FADER  
ACINLF 34  
SWINR 35  
SWINL 36  
FRONT  
REAR  
SW  
SUBWOOFER  
+PHASE  
CONTROL  
ACIN  
OUTPUT  
SELECTOR  
ACOUTR 37  
ACOUTL 38  
MAIN  
SECOND  
CREF 39  
22 VDD  
LP  
VOICE  
BANDPASS  
21 SCL  
20 SDA  
HP  
BASS  
SUPPLY  
19 GND  
18 SM  
TREBLE  
HIGH-CUT  
VOLUME  
SOFTMUTE  
LOUDNESS  
S&H  
PULSE  
FORMER  
25kHz  
LP  
QUAL  
17 QUAL  
COMPANDER  
LOUDNESS  
16 MPOUT  
15 MPIN  
MULTIPATH  
DETECTOR  
DEMODULATOR  
+STEREO ADJUST  
+STEREO BLAND  
MUX 40  
IN-GAIN  
MUTE  
+
BEEP  
D/A  
CONVERTER  
14 LEVEL  
IN-GAIN  
+AUTO ZERO  
PILOT  
CANCELATION  
PIL DET  
PLL  
MAIN SOURCE  
SELECTOR  
MIXING  
SECOND SOURCE  
SELECTOR  
SELECTOR  
MD1 41  
MAIN  
80kHz  
LP  
MD1G 42  
13 MPX  
12 AMIF  
INPUT  
MULTIPLEXER  
FM  
AM  
11  
MD2 43  
PHONO  
MD2G 44  
AM/FM  
NOISE BLANKER  
MAIN  
CH0  
AUX  
1
2
3
4
5
6
7
8
9
10  
IC701 BA8270F-E2  
BUS ON  
14 VCC  
BUS ON  
1
2
3
SWITCH  
RESET  
SWITCH  
13  
RST  
RST  
12 BUS ON  
11 CLK IN  
10 BU IN  
BATTERY  
SWITCH  
BATT  
4
5
6
CLK  
VREF  
DATA  
9
8
DATA IN  
DATA OUT  
GND  
7
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-19. IC PIN FUNCTION DESCRIPTION  
• SERVO BOARD IC301 CXD2652AR  
(DIGITAL SIGNAL PROCESSOR, DIGITAL SERVO PROCESSOR, EFM/ACIRC ENCODER/DECODER,  
SHOCK PROOF MEMORY CONTROLLER, ATRAC ENCODER/DECODER, 2M BIT D-RAM)  
Pin No.  
Pin Name  
I/O  
Description  
Focus OK signal output to the MD mechanism controller (IC501)  
“H” is output when focus is on (“L”: NG)  
1
MNT0  
O
2
3
MNT1  
MNT2  
MNT3  
SWDT  
SCLK  
XLAT  
SRDT  
SENS  
XRST  
O
Track jump detection signal output to the MD mechanism controller (IC501)  
Busy monitor signal output to the MD mechanism controller (IC501)  
O
4
O
Spindle servo lock status monitor signal output to the MD mechanism controller (IC501)  
Writing serial data signal input from the MD mechanism controller (IC501)  
Serial data transfer clock signal input from the MD mechanism controller (IC501)  
Serial data latch pulse signal input from the MD mechanism controller (IC501)  
Reading serial data signal output to the MD mechanism controller (IC501)  
Internal status (SENSE) output to the MD mechanism controller (IC501)  
Reset signal input from the MD mechanism controller (IC501) “L”: reset  
5
I
6
I
7
I
8
O (3)  
O (3)  
I
9
10  
Subcode Q sync (SCOR) output to the MD mechanism controller (IC501)  
“L” is output every 13.3 msec Almost all, “H” is output  
11  
12  
SQSY  
DQSY  
O
O
Digital In U-bit CD format subcode Q sync (SCOR) output terminal  
“L” is output every 13.3 msec Almost all, “H” is output Not used (open)  
Laser power selection signal input terminal  
“L”: playback mode, “H”: recording mode (fixed at “L” in this set)  
13  
14  
RECP  
XINT  
I
O
Interrupt status output to the MD mechanism controller (IC501)  
Recording data output enable signal input terminal  
Writing data transmission timing input (Also serves as the magnetic head on/off output)  
Not used (fixed at “L”)  
15  
TX  
I
16  
17  
OSCI  
I
System clock signal (512Fs=22.5792 MHz) input from the oscillator circuit  
System clock signal (512Fs=22.5792 MHz) output terminal Not used (open)  
OSCO  
O
Input terminal for the system clock frequency setting  
“L”: 45.1584 MHz, “H”: 22.5792 MHz (fixed at “H” in this set)  
18  
XTSL  
I
19  
20  
RVDD  
RVSS  
DIN  
—
—
I
Power supply terminal (+3.3V) (digital system)  
Ground terminal (digital system)  
21  
Digital audio signal input terminal when recording mode Not used (fixed at “L”)  
Digital audio signal output terminal when playback mode Not used (open)  
Recording data input terminal Not used (fixed at “L”)  
Playback data output to the PCM1718E (IC101)  
22  
DOUT  
ADDT  
DADT  
LRCK  
XBCK  
FS256  
DVDD  
A03 to A00  
A10  
O
I
23  
24  
O
O
O
O
—
O
O
O
O
—
O
O
O
O
O
25  
L/R sampling clock signal (44.1 kHz) output to the PCM1718E (IC101)  
Bit clock signal (2.8224 MHz) output to the PCM1718E (IC101)  
Clock signal (11.2896 MHz) output to the PCM1718E (IC101)  
Power supply terminal (+3.3V) (digital system)  
26  
27  
28  
29 to 32  
33  
Address signal output to the D-RAM (IC307)  
Address signal output to the external D-RAM Not used (open)  
Address signal output to the D-RAM (IC307)  
34 to 38  
39  
A04 to A08  
A11  
Address signal output to the external D-RAM Not used (open)  
Ground terminal (digital system)  
40  
DVSS  
XOE  
41  
Output enable signal output to the D-RAM (IC307) “L” active  
Column address strobe signal output to the D-RAM (IC307) “L” active  
Address signal output to the D-RAM (IC307)  
42  
XCAS  
A09  
43  
44  
XRAS  
XWE  
Row address strobe signal output to the D-RAM (IC307) “L” active  
Write enable signal output to the D-RAM (IC307) “L” active  
45  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Pin No.  
46  
47  
48  
49  
50  
51  
52  
53  
54  
55  
56  
57  
58  
59  
60  
61  
62  
63  
64  
65  
66  
67  
68  
69  
70  
71  
72  
73  
74  
75  
76  
77  
78  
79  
80  
81  
82  
Pin Name  
D1  
I/O  
I/O  
I/O  
I/O  
I/O  
I
Description  
D0  
Two-way data bus with the D-RAM (IC307)  
D2  
D3  
MVCI  
ASYO  
ASYI  
AVDD  
BIAS  
RFI  
Digital in PLL oscillation input from the external VCO Not used (fixed at “L”)  
Playback EFM full-swing output terminal  
O
I (A) Playback EFM asymmetry comparator voltage input terminal  
Power supply terminal (+3.3V) (analog system)  
—
I (A) Playback EFM asymmetry circuit constant current input terminal  
I (A) Playback EFM RF signal input from the CXA2523AR (IC302)  
AVSS  
PDO  
—
Ground terminal (analog system)  
O (3) Phase comparison output for clock playback analog PLL of the playback EFM Not used (open)  
O (3) Phase comparison output for master clock of the recording/playback EFM master PLL  
I (A) Filter input for master clock of the recording/playback master PLL  
PCO  
FILI  
FILO  
CLTV  
PEAK  
BOTM  
ABCD  
FE  
O (A) Filter output for master clock of the recording/playback master PLL  
I (A) Internal VCO control voltage input of the recording/playback master PLL  
I (A) Light amount signal (RF/ABCD) peak hold input from the CXA2523AR (IC302)  
I (A) Light amount signal (RF/ABCD) bottom hold input from the CXA2523AR (IC302)  
I (A) Light amount signal (ABCD) input from the CXA2523AR (IC302)  
I (A) Focus error signal input from the CXA2523AR (IC302)  
AUX1  
VC  
I (A) Auxiliary signal (I3 signal/temperature signal) input terminal Not used (fixed at “H”)  
I (A) Middle point voltage (+1.65V) input from the CXA2523AR (IC302)  
O (A) Monitor output of the A/D converter input signal Not used (open)  
ADIO  
AVDD  
ADRT  
ADRB  
AVSS  
SE  
—
Power supply terminal (+3.3V) (analog system)  
I (A) A/D converter operational range upper limit voltage input terminal (fixed at “H” in this set)  
I (A) A/D converter operational range lower limit voltage input terminal (fixed at “L” in this set)  
—
Ground terminal (analog system)  
I (A) Sled error signal input from the CXA2523AR (IC302)  
TE  
I (A) Tracking error signal input from the CXA2523AR (IC302)  
I (A) Auxiliary signal input terminal Light amount signal input from the CXA2523AR (IC302)  
I (A) Connected to the +3.3V power supply  
AUX2  
DCHG  
APC  
I (A) Error signal input for the laser automatic power control Not used (fixed at “L”)  
ADFG  
F0CNT  
XLRF  
CKRF  
DTRF  
I
ADIP duplex FM signal (22.05 kHz ± 1 kHz) input from the CXA2523AR (IC302)  
Filter f0 control signal output terminal Not used (open)  
O
O
O
O
Serial data latch pulse signal output terminal Not used (open)  
Serial data transfer clock signal output terminal Not used (open)  
Writing serial data output terminal Not used (open)  
Control signal output to the reference voltage generator circuit for the laser automatic power  
control  
83  
APCREF  
O
84  
85  
86  
87  
88  
LDDR  
TRDR  
TFDR  
DVDD  
FFDR  
O
O
PWM signal output for the laser automatic power control Not used (open)  
Tracking servo drive PWM signal (–) output to the BH6511FS (IC303)  
Tracking servo drive PWM signal (+) output to the BH6511FS (IC303)  
Power supply terminal (+3.3V) (digital system)  
O
—
O
Focus servo drive PWM signal (+) output to the BH6511FS (IC303)  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Pin No.  
89  
Pin Name  
FRDR  
FS4  
I/O  
O
O
O
O
O
O
I
Description  
Focus servo drive PWM signal (–) output to the BH6511FS (IC303)  
Clock signal (176.4 kHz) output terminal (X’tal system) Not used (open)  
Sled servo drive PWM signal (–) output to the BH6511FS (IC303)  
Sled servo drive PWM signal (+) output to the BH6511FS (IC303)  
Spindle servo drive PWM signal (–) output to the BH6511FS (IC303)  
Spindle servo drive PWM signal (+) output to the BH6511FS (IC303)  
Not used (fixed at “L”)  
90  
91  
SRDR  
SFDR  
SPRD  
SPFD  
92  
93  
94  
95  
FGIN  
96  
TEST1  
TEST2  
TEST3  
DVSS  
EFMO  
I
97  
I
Input terminal for the test (fixed at “L”)  
98  
I
99  
—
O
Ground terminal (digital system)  
100  
EFM signal output terminal when recording mode Not used (open)  
* I (A) for analog input, O (3) for 3-state output, and O (A) for analog output in the column I/O.  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• SERVO BOARD IC302 CXA2523AR (RF AMP, FOCUS/TRACKING ERROR AMP)  
Pin No.  
1
Pin Name  
I
I/O  
I
Description  
I-V converted RF signal I input from the optical pick-up block detector  
I-V converted RF signal J input from the optical pick-up block detector  
Middle point voltage (+1.65V) generation output terminal  
Signal input from the optical pick-up detector  
2
J
I
3
VC  
O
I
4 to 9  
10  
A to F  
PD  
I
Light amount monitor input from the optical pick-up block laser diode  
Laser amplifier output terminal to the automatic power control circuit  
Reference voltage input terminal for setting laser power  
11  
APC  
O
I
12  
APCREF  
GND  
13  
—
I
Ground terminal  
14  
TEMPI  
TEMPR  
SWDT  
SCLK  
XLAT  
XSTBY  
Connected to the temperature sensor Not used (open)  
O
I
15  
Output terminal for a temperature sensor reference voltage Not used (open)  
Writing serial data input from the MD mechanism controller (IC501)  
Serial data transfer clock signal input from the MD mechanism controller (IC501)  
Serial data latch pulse signal input from the MD mechanism controller (IC501)  
Standby signal input terminal “L”: standby (fixed at “H” in this set)  
16  
17  
I
18  
I
19  
I
Center frequency control voltage input terminal of internal circuit (BPF22, BPF3T, EQ) input  
terminal  
20  
F0CNT  
I
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
47  
48  
VREF  
EQADJ  
3TADJ  
VCC  
O
I
Reference voltage output terminal Not used (open)  
Center frequency setting terminal for the internal circuit (EQ)  
Center frequency setting terminal for the internal circuit (BPF3T)  
Power supply terminal (+3.3V)  
I
—
I
WBLADJ  
TE  
Center frequency setting terminal for the internal circuit (BPF22)  
Tracking error signal output to the CXD2652AR (IC301)  
Connected to the external capacitor for low-pass filter of the sled error signal  
Sled error signal output to the CXD2652AR (IC301)  
FM signal output of the ADIP  
O
I
CSLED  
SE  
O
O
I
ADFM  
ADIN  
ADAGC  
ADFG  
AUX  
Receives a ADIP FM signal in AC coupling  
I
Connected to the external capacitor for ADIP AGC  
O
O
O
O
O
O
O
I
ADIP duplex signal (22.05 kHz ± 1 kHz) output to the CXD2652AR (IC301)  
Auxiliary signal (I3 signal/temperature signal) output terminal Not used (open)  
Focus error signal output to the CXD2652AR (IC301)  
Light amount signal (ABCD) output to the CXD2652AR (IC301)  
Light amount signal (RF/ABCD) bottom hold output to the CXD2652AR (IC301)  
Light amount signal (RF/ABCD) peak hold output to the CXD2652AR (IC301)  
Playback EFM RF signal output to the CXD2652AR (IC301)  
Connected to the external capacitor for RF auto gain control circuit  
Receives a RF signal in AC coupling  
FE  
ABCD  
BOTM  
PEAK  
RF  
RFAGC  
AGCI  
COMPO  
COMPP  
ADDC  
OPO  
I
O
I
User comparator output terminal Not used (open)  
User comparator input terminal Not used (fixed at “L”)  
Connected to the external capacitor for cutting the low band of the ADIP amplifier  
User operational amplifier output terminal Not used (open)  
User operational amplifier inversion input terminal Not used (fixed at “L”)  
RF signal output terminal  
I
O
I
OPN  
RFO  
O
I
MORFI  
MORFO  
Receives a MO RF signal in AC coupling  
O
MO RF signal output terminal  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• SERVO BOARD IC501 CXP84340-217Q (MD MECHANISM CONTROLLER)  
Pin No.  
Pin Name  
TIN3 to TIN7  
LOAD  
I/O  
I/O  
O
Description  
1 to 5  
6
Input of the 4×8 matrix test keys (“L” is always output, except in test mode) Not used (open)  
Loading motor control signal output to the motor driver (IC305) “H” active *1  
Loading motor control signal output to the motor driver (IC305) “H” active *1  
Not used (open)  
7
EJECT  
O
8, 9  
NCO  
O
Power supply on/off control signal output of the MD mechanism deck section main power supply  
and loading motor drive (IC305) power supply “H”: power on  
10  
MDMON  
O
Inputs the disc loading completion detect switch detection signal  
“L”: When completed of the disc loading operation  
11  
12  
E-SW  
AG-OK  
ADJ-OK  
NCO  
I
O
O
O
I
Output of aging status in test mode “L”: under aging, “H”: aging completed Not used (open)  
Output of status when aging completed in test mode “L”: aging NG, “H”: aging OK  
Not used (open)  
13  
14 to 17  
18  
Not used (open)  
Select whether defect function is used for the CXD2652AR (IC301)  
“L”: used this function , “H”: not used this function (fixed at “H” in this set)  
DFCTSEL  
Select whether digital PLL function is used for the CXD2652AR (IC301)  
“L”: used this function , “H”: not used this function (fixed at “H” in this set)  
19  
20  
DPLLSEL  
EMPHSEL  
I
I
Select whether emphasis signal output from pin or unilink data  
“L”: outputs from both pin and unilink data, “H”: output from pin only (fixed at “H” in this set)  
21  
22  
LOCK  
NCO  
O
O
Mini-disc lock detection signal output to the master controller (IC501) “H”: lock  
Not used (open)  
Select whether D-RAM capacitance 2M bit or 4M bit “L”: 4M bit (external D-RAM) , “H”: 2M  
bit (internal D-RAM of CXD2652AR) (fixed at “L” in this set)  
23  
24, 25  
26  
2M/4M  
NCO  
I
O
I
Not used (open)  
Focus OK signal input from the CXD2652AR (IC301)  
“H” is input when focus is on (“L”: NG)  
MNT0  
27  
28  
29  
MNT1  
MNT2  
MNT3  
I
I
I
Track jump detection signal input from the CXD2652AR (IC301)  
Busy monitor signal input from the CXD2652AR (IC301)  
Spindle servo lock status monitor signal input from the CXD2652AR (IC301)  
System reset signal input from the master controller (IC501), reset signal generator (IC652) and  
reset switch (SW503) “L”: reset  
30  
RESET  
I
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”  
31  
32  
33  
34  
35  
36  
37  
38  
39  
EXTAL  
XTAL  
VSS  
O
I
Main system clock output terminal (10 MHz)  
Main system clock input terminal (10 MHz)  
—
O
I
Ground terminal  
TX  
Sub system clock output terminal (32.768 kHz) Not used (open)  
Sub system clock input terminal (32.768 kHz) Not used (fixed at “L”)  
Ground terminal (for A/D converter)  
TEX  
AVSS  
AVREF  
INIT  
—
I
Reference voltage input terminal (+5V) (for A/D converter)  
Initial reset signal input terminal (A/D input) (fixed at “H”)  
Temperature sensor (TH501) input terminal (A/D input)  
I
TEMP  
I
Select the number of load/eject aging times (A/D input)  
0H – 54H (30 times), 55H – OA9H (20 times), OAAH – OFFH (10 times)  
40  
ACNT  
I
41  
42  
43  
44  
45  
46  
DO-SEL  
EE-CS  
I
O
Select the digital output bits (A/D input)  
Chip select signal output to the external EEPROM device Not used (open)  
Serial data transfer clock signal output to the external EEPROM device Not used (open)  
Two way data bus with the external EEPROM device Not used (open)  
Writing serial data signal output to the CXD2652AR (IC301) and CXA2523AR (IC302)  
Unilink on/off control signal output for the SONY bus “L”: link on, “H”: link off  
EE-CKO  
EE-SIO  
O
I/O  
O
MD-SO  
LINKOFF  
O
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Pin No.  
Pin Name  
I/O  
Description  
47  
UNIREQ  
O
Data request signal output terminal (for SONY bus) “H”: request on Not used (open)  
Serial clock signal input from the master controller (IC501) or serial clock signal output to the  
SONY bus interface (IC701) and master controller (IC501) (for SONY bus)  
48  
UNICKIO  
I/O  
49  
50  
51  
52  
53  
54  
55  
UNISI  
UNISO  
MD-CKO  
MD-SI  
I
O
O
I
Serial data input from the SONY bus interface (IC701)  
Serial data output to the SONY bus interface (IC701)  
Serial data transfer clock signal output to the CXD2652AR (IC301) and CXA2523AR (IC302)  
Reading serial data signal input from the CXD2652AR (IC301)  
Not used (open)  
NCO  
O
I
SENS  
Internal status (SENSE) input from the CXD2652AR (IC301)  
Interrupt status input from the CXD2652AR (IC301)  
CC-XINT  
I
Detection input from the sled limit-in detect switch  
The optical pick-up is inner position when “L”  
56  
LIMIT-IN  
I
57  
58  
EJT-KEY  
I
Eject request signal input terminal “L”: eject on Not used (fixed at “H”)  
ERROR-PWM  
O
PWM error monitor output terminal (C1and ATER is output when test mode) Not used (open)  
Reset signal output to the PCM1718E (IC101), CXD2652AR (IC301) and BH6511FS (IC303)  
“L”: reset  
59  
MD-RST  
O
Battery detect signal input from the SONY bus interface (IC600) and battery check circuit  
“H”: battery on  
60  
61  
62  
BU-IN  
BUS-ON  
SQSY  
I
I
I
SONY bus on/off control signal input from the master controller (IC700) “L”: bus on  
Subcode Q sync (SCOR) input from the CXD2652AR (IC301)  
“L” is input every 13.3 msec Almost all, “H” is input  
Inputs the disc loading start or disc eject completion detect switch detection signal  
“L”: When start or eject completed of the disc loading operation  
63  
64  
65  
C-SW  
MD-LAT  
MD-ON  
I
O
O
Serial data latch pulse signal output to the CXD2652AR (IC301) and CXA2523AR (IC302)  
Power supply on/off control signal output of the MD mechanism deck section main power supply  
“H”: power on  
66  
67  
DEEMP  
A-MUTE  
NCO  
O
O
O
O
O
I
Emphasis on/off control signal output to the PCM1718E (IC101) “H”: emphasis on  
Audio muting on/off control signal output terminal  
Not used (open)  
68  
69  
TSTCKO  
TSTSO  
Output of clock signal for the test mode display Not used (open)  
Output of data for the test mode display Not used (open)  
Setting terminal for the test mode “L”: test mode, “H”: normal mode  
Power supply terminal (+5V)  
70  
71  
TSTMOD  
VCC  
72  
—
I
73  
NIL  
Not used (fixed at “H”)  
TOUT0 to TOUT3  
74 to 77  
78 to 80  
O
I/O  
Output of the 4×8 matrix test keys Not used (open)  
Input of the 4×8 matrix test keys (“L” is always output, except in test mode) Not used (open)  
TIN0 to TIN2  
*1 Loading motor (M903) control  
Operation  
IN  
OUT  
BRAKE  
STOP  
Terminal  
“H”  
“L”  
“H”  
“L”  
LOAD (pin 6)  
“L”  
“H”  
“H”  
“L”  
EJECT (pin 7)  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• MAIN BOARD IC501 MB90574PMT-G-266-BND (MASTER CONTROLLER)  
Pin No.  
Pin Name  
I/O  
Description  
Tuner system power supply on/off control signal output to the BA4908 (IC671)  
“H”: tuner power on  
1
TUNON  
O
Tuner system power supply on/off control signal output terminal “H”: tuner power on  
Not used (open)  
2
ANT CUT  
O
Bus on/off control signal output to the MD mechanism controller (IC501) and SONY bus  
interface (IC701) “L”: bus on  
3
4 to 6  
7
BUSON  
NCO  
O
O
Not used (open)  
Power on/off control signal output of the illumination LED and liquid crystal display driver  
(IC901) “H”: power on  
ILLON  
O
8
9
VCC  
—
Power supply terminal (+5V)  
E2P SIO  
E2P CKO  
I/O Two-way data E2P bus with the FM/AM tuner unit (TU1)  
O
10  
E2P bus clock signal output to the FM/AM tuner unit (TU1)  
System reset signal output to the MD mechanism controller (IC501) and SONY bus interface  
(IC701) “L”: reset  
11  
12  
SYSRST  
O
Front panel open/close detection signal input terminal  
“L” is input when the front panel is closed  
DOORSW  
I
13  
14  
15  
16  
17  
18  
LCDSO  
LCDCKO  
LCDCE  
BEEP  
O
O
O
O
I
Serial data output to the liquid crystal display driver (IC901)  
Serial data transfer clock signal output to the liquid crystal display driver (IC901)  
Chip enable signal output to the liquid crystal display driver (IC901) “H” active  
Beep sound drive signal output to the power amplifier (IC611)  
Serial data input from the SONY bus interface (IC701)  
UNISI  
UNISO  
O
Serial data output to the SONY bus interface (IC701)  
Serial clock signal output to the MD mechanism controller (IC501) and SONY bus interface  
(IC701)  
19  
20  
21  
UNICKO  
UNICKI  
CD MD  
O
I
Serial clock signal input from the MD mechanism controller (IC501) (for SONY bus)  
Setting terminal for the internal mechanism CD or MD  
“L”: CD, “H”: MD (fixed at “H” in this set)  
I
Internal flash memory data write mode detection signal input terminal “L”: data write mode  
Not used  
22  
I
FLASHW  
23  
24  
NCO  
SIRCS  
NCO  
O
I
Not used (open)  
Sircs remote control signal input from the remote control receiver (IC951)  
Not used (open)  
25 to 28  
O
LED drive signal output of the MD disc slot illumination and Z indicator (LED810, LSW810)  
“H”: LED on “H” is output to turn on LED when front panel is opened  
29  
DOORIND  
O
30, 31  
32  
NCO  
NS MASK  
VSS  
O
O
Not used (open)  
Discharge control signal output for the noise detection circuit “H”: discharge  
Ground terminal  
33  
—
—
34  
C
Connected to coupling capacitor for the power supply  
A/D converter power control signal output terminal  
35  
AD ON  
O
When the KEYACK (pin uh) that controls reference voltage power for key A/D conversion input  
is active, “L” is output from this terminal to enable the input  
36  
REIN0  
I
Dial pulse input of the rotary encoder (RE901)  
(for VOLUME/BASS/TREBLE/BALANCE/FADER control)  
37  
38  
REIN1  
DVCC  
DVSS  
NCO  
I
—
—
O
Power supply terminal (+5V) (for D/A converter)  
Ground terminal (for D/A converter)  
Not used (open)  
39  
40, 41  
42  
AVCC  
—
Power supply terminal (+5V) (for analog system)  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Pin No.  
43  
Pin Name  
AVRH  
I/O  
I
Description  
Reference voltage (+5V) input terminal (for A/D converter)  
Reference voltage (0V) input terminal (for A/D converter)  
Ground terminal (for analog system)  
44  
AVRL  
I
45  
AVSS  
—
Key input terminal (A/D input) (LSW901 to LSW908, S901 to S904)  
OFF, SOURCE, SOUND, MENU, PTY DSPL, LIST, ENTER, MODE,  
SEEK/AMS - . m + > M, DISC/PRST +, PRST/DISC - keys input  
46  
KEYIN0  
I
Key input terminal (A/D input) (LSW810, LSW909 to LSW917)  
Z, D-BASS, TA, FA, 6 to 3 SHUF 2, REP 1 keys input  
47  
KEYIN1  
I
48  
49  
50  
51  
52  
RCIN0  
DSTSEL  
QUALITY  
FMAGC  
MPTH  
I
I
I
I
I
Rotary remote commander key input terminal (A/D input)  
Destination setting terminal (fixed at “L” in this set)  
Noise level detection signal input at SEEK mode (A/D input)  
FM AGC detection signal input from the FM/AM tuner unit (TU1) (A/D input)  
Multi-path detection signal input from the RDS decoder (IC51) (A/D input)  
FM and AM signal meter voltage detection input from the FM/AM tuner unit (TU1)  
(A/D input)  
53  
54  
VSM  
VCC  
I
—
Power supply terminal (+5V)  
Internal RAM reset detection signal input terminal  
55  
RAMBU  
I
Input terminal to check that RAM data are not destroyed due to low voltage  
This checking is made within 100 msec after reset Not used (fixed at “H”)  
56  
57  
58  
59  
TUNATT  
VOLATT  
ATT  
O
O
O
O
Muting on/off control signal output of the FM/AM tuner signal “H”: muting on  
Pre amplifier muting on/off control signal output to the electrical volume (IC151)  
“L”: muting on  
Audio line muting on/off control signal output terminal “H”: muting on  
Standby on/off control signal output to the power amplifier (IC611)  
“L”: standby mode, “H”: ampifier on  
AMPON  
Power amplifier muting on/off control signal output to the power amplifier (IC611)  
“L”: muting on  
60  
AMPATT  
O
61  
62  
63  
64  
65  
66  
COLSW  
COLSEL  
VSS  
I
I
Setting terminal for the illumination color “L”: 2 color, “H”: 1 color (fixed at “H” in this set)  
Setting terminal for the illumination color “L”: amber, “H”: green (fixed at “L” in this set)  
Ground terminal  
—
I
DAVN  
FILE  
Data transmit completed detection signal input from the RDS decoder (IC51) “H” active  
Setting terminal for the custom file “L”: unavailable, “H”: available (fixed at “H” in this set)  
Setting terminal for the CD text “L”: unavailable, “H”: available (fixed at “H” in this set)  
I
TEXT  
I
Front panel block remove/attach detection signal input from the nose detection switch (SW504)  
“L”: front panel is attached  
67  
68, 69  
70  
NOSESW  
NCO  
I
O
Not used (open)  
Two-way data I2C bus with the FM/AM tuner unit (TU1), RDS decoder (IC51) and electrical  
volume (IC151)  
I2C SIO  
I/O  
I2C bus clock signal output to the FM/AM tuner unit (TU1), RDS decoder (IC51) and electrical  
volume (IC151)  
71  
I2C CKO  
O
72  
73  
74  
75  
NCO  
X1A  
X0A  
NCO  
O
O
I
Not used (open)  
Sub system clock output terminal (32.768 kHz)  
Sub system clock input terminal (32.768 kHz)  
Not used (open)  
O
Input of acknowledge signal for the key entry Acknowledge signal is input to accept function  
and eject keys in the power off status On at input of “H”  
76  
77  
KEYACK  
BUIN  
I
I
Battery detection signal input from the SONY bus interface (IC701) and battery detect circuit  
“L” is input at low voltage  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Pin No.  
Pin Name  
I/O  
Description  
Auto dimmer control illumination line detection signal input terminal  
“H” is input at dimmer detection Not used (fixed at “L”)  
78  
ILLIN  
I
Telephone detection signal input terminal At input of “H”, the signal is attenuated by –20 dB  
Used for the MDX-C6500R/C6500RX only (MDX-C6400R: fixed at “L”)  
79  
TELATT  
I
80  
81  
82  
83  
84  
85  
86  
87  
88  
89  
NCO  
TEST IN  
ACC IN  
NCO  
O
I
Not used (open)  
Setting terminal for the test mode “L”: test mode, Normally: fixed at “H”  
Accessory detection signal input terminal “L”: accessory on  
Not used (open)  
I
O
I
LOCKIN  
RCIN1  
HSTX  
MD2  
Mini-disc lock detection signal input from the MD mechanism controller (IC501) “H”: lock  
Rotary remote commander shift key input terminal “L”: shift  
Hardware standby input terminal “L”: hardware standby mode Reset signal input in this set  
Setting terminal for the CPU operational mode (fixed at “L” in this set)  
Setting terminal for the CPU operational mode (fixed at “H” in this set)  
Setting terminal for the CPU operational mode (fixed at “H” in this set)  
I
I
I
MD1  
I
MD0  
I
System reset signal input from the reset signal generator (IC652) and reset switch (SW503)  
“L”: reset “L” is input for several 100 msec after power on, then it changes to “H”  
90  
RSTX  
I
91  
92  
VSS  
X0  
—
I
Ground terminal  
Main system clock input terminal (3.68 MHz)  
Main system clock output terminal (3.68 MHz)  
Power supply terminal (+5V)  
93  
X1  
O
—
O
I
94  
VCC  
NCO  
DIM SEL  
95 to 97  
98  
Not used (open)  
Setting terminal for the dimmer “L”: dimmer in, “H”: no dimmer (fixed at “H” in this set)  
Setting terminal for the internal mechanism tape or CD  
“L”: CD, “H”: tape (fixed at “L” in this set)  
99  
TAP CD  
I
100, 101  
102  
NCO  
O
I
Not used (open)  
AMTL IN  
Auto metal detection signal input terminal “L”: auto metal Not used (open)  
Input terminal of whether a music is present or not is detected at auto music sensor  
“L”: music is present, “H”: music is not present Not used (open)  
103  
AMS IN  
I
104  
105  
106  
107  
108  
REEL  
POS0  
POS1  
POS2  
POS3  
I
I
I
I
I
Rotation detect signal input terminal Not used (open)  
Tape position (EJECT/FF/REW/REV/  
FWD mode) detect input from the tape  
operation switch on the deck mechanism  
Not used this function (open)  
POS0: “L”: EJECT mode, “H”: others mode  
POS1: “L”: FF and FWD mode, “H”: others mode  
POS2: “L”: REW mode, “H”: others mode  
POS3: “L”: REV and EJECT mode, “H”: others mode  
Loading motor control signal output terminal “H” active  
(For the eject direction and reverse side operation) Not used (open)  
109  
110  
LM EJ  
O
O
Loading motor control signal output terminal “H” active  
(For the loading direction and forward side operation) Not used (open)  
LM LD  
111  
112  
CM ON  
TAPON  
O
O
Capstan/reel motor control signal output terminal “H”: motor on Not used (open)  
Tape system power supply on/off control signal output terminal “H”: tape on Not used (open)  
Forward/reverse direction control signal output terminal  
“L”: forward direction, “H”: reverse direction Not used (open)  
113  
114  
N ROUT  
AMSON  
O
O
Tape auto music sensor control signal output terminal  
“L” is output to lower the gain for audio level at FF/REW mode Not used (open)  
METAL control in/out terminal  
At initial mode: auto/manual mode selection input of METAL function (manual at “L” input)  
At manual mode: METAL on/off control signal output terminal (METAL on at “H” output)  
Not used this function (open)  
115  
MTLON  
I/O  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Pin No.  
Pin Name  
I/O  
Description  
Dolby control in/out terminal  
At initial mode: valid/invalid selection input of dolby function (valid at “L” input)  
At normal mode: dolby on/off control signal output terminal (dolby on at “H” output)  
Not used this function (open)  
116  
DOLON  
I/O  
117  
118  
119  
120  
TAPATT  
NCO  
O
O
Audio signal select control signal output terminal Not used (open)  
Not used (open)  
VSS  
—
O
Ground terminal  
PW ON  
Main system power supply on/off control signal output to the BA4908 (IC671) “H”: power on  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ver 1.2  
SECTION 5  
EXPLODED VIEWS  
NOTE:  
• -XX and -X mean standardized parts, so they  
may have some difference from the original  
one.  
• Color Indication of Appearance Parts  
Example:  
•
Items marked “*” are not stocked since they  
are seldom required for routine service. Some  
delay should be anticipated when ordering  
these items.  
The mechanical parts with no reference num-  
ber in the exploded views are not supplied.  
Hardware (# mark) list and accessories and  
packing materials are given in the last of the  
electrical parts list.  
The components identified by  
mark 0 or dotted line with mark  
0 are critical for safety.  
Replace only with part number  
specified.  
•
•
KNOB, BALANCE (WHITE) . . . (RED)  
↑
↑
Parts Color Cabinet's Color  
#11  
(1) GENERAL SECTION  
#11  
13  
14  
B
FU601  
#3  
C6500R/  
C6500RX  
15  
11  
#3  
#3  
12  
MG-164NZ-138  
#2  
#4  
TU1  
A
9
10  
#4  
2
16  
21  
#11  
not  
supplied  
22  
3
8
B
7
4
17  
A
#11  
Front panel section  
#10  
5
18  
19  
6
#1  
#12  
#10  
#1  
#10  
CNP811  
1
Ref. No.  
Part No.  
Description  
Remark  
Ref. No.  
Part No.  
Description  
Remark  
1
2
3
4
5
X-3378-458-1 PANEL ASSY, SUB  
X-3376-699-2 GEAR ASSY  
3-030-909-02 DAMPER, OIL  
3-713-786-51 SCREW +P 2X3  
3-034-086-01 SPRING (DOOR)  
* 14  
* 15  
* 15  
* 16  
17  
3-040-995-01 COVER  
3-040-996-11 HEAT SINK (2P) (C6400R)  
3-040-996-21 HEAT SINK (2P) (C6500R/C6500RX)  
3-045-878-01 PLATE (TU), GROUND  
1-776-527-51 CORD (WITH CONNECTOR) (ISO) (POWER)  
(C6400R)  
6
7
* 8  
* 9  
* 9  
3-033-750-02 DOOR (MD)  
3-040-990-01 BUTTON (EJECT) (Z)  
1-677-057-11 SUB BOARD  
A-3294-867-A MAIN BOARD, COMPLETE (C6400R)  
A-3294-868-A MAIN BOARD, COMPLETE (C6500RX)  
17  
1-776-527-61 CORD (WITH CONNECTOR) (ISO) (POWER)  
(C6500R/C6500RX)  
3-040-994-21 CHASSIS  
* 18  
19  
X-3377-621-2 LOCK ASSY  
* 21  
* 22  
3-045-877-01 CUSHION (TU)  
3-045-828-01 INSULATED PLATE  
* 9  
* 10  
A-3294-943-A MAIN BOARD, COMPLETE (C6500R)  
3-041-011-01 HEAT SINK (REG)  
11  
* 12  
* 13  
3-376-464-11 SCREW (+PTT 2.6X6), GROUND POINT  
3-040-998-01 BRACKET (IC)  
3-041-017-01 BRACKET (MD)  
CNP811 1-792-195-11 CABLE, FLEXIBLE, FLAT  
FU601 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) (10A)  
TU1  
A-3220-812-A TUNER UNIT (TUX-020)  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(2) FRONT PANEL SECTION  
#13  
not supplied  
(KEY board)  
56  
55  
64  
59  
63  
62  
53  
61  
54  
60  
66  
LCD901  
65  
67  
52  
68  
69  
51  
Ref. No.  
Part No.  
Description  
Remark  
Ref. No.  
Part No.  
Description  
Remark  
51  
52  
53  
54  
55  
3-041-010-01 BUTTON (1-6/M) (MODE. 1. 2. 3. 4. 5. 6)  
3-040-987-01 BUTTON (OFF)  
3-040-986-01 BUTTON (MENU/SOUND)  
3-041-003-01 BUTTON (LIST/ENTER) (DSPL. LIST. ENTER)  
3-040-980-01 BUTTON (SOURCE)  
64  
65  
66  
67  
68  
X-3378-398-1 PANEL ASSY, FRONT BACK  
3-935-151-01 SPRING (OPEN)  
3-040-989-01 BUTTON (OPEN)  
3-041-005-11 BUTTON (D) (D-BASS)  
3-041-006-01 BUTTON (AF/TA)  
56  
* 59  
60  
* 61  
* 62  
3-040-981-01 KNOB (VOL)  
69  
69  
69  
X-3378-685-1 FRONT PANEL (SV) ASSY (C6500R)  
X-3378-686-1 FRONT PANEL (SV) ASSY (C6400R)  
X-3378-688-1 FRONT PANEL (SV) ASSY (C6500RX)  
3-040-997-01 PLATE (LCD), GROUND  
1-694-660-11 CONDUCTIVE BOARD, CONNECTION  
3-041-371-01 SHEET (REFLECTOR)  
3-040-993-01 PLATE (LCD), LIGHT GUIDE  
LCD901 1-803-906-11 DISPLAY PANEL, LIQUID CRYSTAL  
(C6400R/C6500R)  
LCD901 1-803-906-31 DISPLAY PANEL, LIQUID CRYSTAL (C6500RX)  
* 63  
3-040-992-01 HOLDER (LCD)  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(3) MECHANISM DECK SECTION-1  
(MG-164NZ-138)  
112  
#8  
113  
114  
#6  
106  
111  
107  
109  
115  
109  
110  
116  
109  
117  
118  
105  
#6  
#6  
#6  
111  
105  
104  
108  
103  
103  
104  
102  
101  
#5  
Ref. No.  
Part No.  
Description  
Remark  
Ref. No.  
Part No.  
Description  
Remark  
* 101  
* 102  
103  
104  
105  
A-3326-036-A SERVO BOARD, COMPLETE  
X-3376-799-1 CHASSIS ASSY, MD  
3-032-714-02 SPRING (FLOAT F), TENSION  
3-921-111-01 SPRING (FLOAT B), TENSION  
3-919-273-01 DAMPER, OIL  
* 110  
111  
* 112  
113  
3-032-712-01 LEVER (LOCK R)  
3-919-281-01 SPRING (CHUCKING)  
X-3376-800-1 COVER ASSY, MD  
3-035-932-01 WASHER, STOPPER  
X-3376-797-3 LEVER (LE) ASSY  
* 114  
* 106  
107  
* 108  
* 109  
X-3376-796-3 HOLDER ASSY  
3-032-682-01 SPRING (HOLDER)  
3-034-301-01 CUSHION (EJ2)  
3-034-302-01 CUSHION (EJ3)  
115  
116  
* 117  
* 118  
3-032-707-01 SPRING (LEVER LE)  
3-925-034-01 ROLLER (GEAR E)  
X-3376-798-1 ARM ASSY, CHUCKING  
3-032-711-01 LEVER (LOCK L)  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(4) MECHANISM DECK SECTION-2  
(MG-164NZ-138)  
157  
158  
M903  
159  
M901  
156  
#9  
161  
#9  
155  
#7  
162  
#8  
160  
164  
163  
M902  
#8  
154  
165  
#7  
152  
153  
166  
151  
The components identified by mark 0 or dotted  
line with mark 0 are critical for safety.  
Replace only with part number specified.  
Ref. No.  
Part No.  
Description  
Remark  
Ref. No.  
Part No.  
Description  
Remark  
151  
152  
153  
154  
* 155  
2-626-617-01 SCREW (2X8)  
161  
162  
163  
164  
0165  
X-3373-213-1 SCREW ASSY, FEED  
3-939-590-07 SCREW (IB LOCK)  
3-010-091-01 SPRING (SL FEED)  
3-919-293-01 SHAFT (OPT S), GUIDE  
8-583-065-03 OPTICAL PICK-UP KMS-241C/J1RP  
A-3326-034-A SENSOR BOARD, COMPLETE  
1-654-693-11 SENSOR FLEXIBLE BOARD  
3-919-283-01 BRACKET (SL)  
3-032-704-01 BASE (SL)  
156  
157  
158  
159  
* 160  
3-919-297-01 BRACKET (SP)  
A-3301-750-A CHASSIS (OP) ASSY  
3-032-660-01 BRACKET (LO)  
3-032-669-01 SPRING (RACK), TENSION  
3-032-705-01 BEARING (SL)  
166  
3-920-537-01 SHAFT (OPT L), GUIDE  
M901  
M902  
M903  
A-3301-407-A MOTOR ASSY, SP (SPINDLE)  
A-3291-190-A MOTOR ASSY, SL (SLED)  
A-3291-191-A MOTOR ASSY, LO (LOADING)  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION 6  
ELECTRICAL PARTS LIST  
KEY  
NOTE:  
• Due to standardization, replacements in the  
parts list may be different from the parts speci-  
fied in the diagrams or the components used  
on the set.  
• -XX and -X mean standardized parts, so they  
may have some difference from the original  
one.  
• RESISTORS  
All resistors are in ohms.  
METAL: Metal-film resistor.  
METAL OXIDE: Metal oxide-film resistor.  
F: nonflammable  
•
Items marked “*” are not stocked since they  
are seldom required for routine service.  
Some delay should be anticipated when order-  
ing these items.  
SEMICONDUCTORS  
In each case, u: µ, for example:  
The components identified by  
mark 0 or dotted line with mark  
0 are critical for safety.  
Replace only with part number  
specified.  
•
When indicating parts by reference  
number, please include the board.  
uA. . : µA. .  
uPB. . : µPB. .  
uPD. . : µPD. .  
CAPACITORS  
uF: µF  
uPA. . : µPA. .  
uPC. . : µPC. .  
•
•
COILS  
uH: µH  
Ref. No.  
Part No.  
Description  
Remark  
Ref. No.  
Part No.  
Description  
Remark  
KEY BOARD  
LED902 8-719-038-07 LED CL-190PG-CD-T (ILLUMINATION)  
**********  
(GREEN)  
1-694-660-11 CONDUCTIVE BOARD, CONNECTION  
3-040-992-01 HOLDER (LCD)  
3-040-993-01 PLATE (LCD), LIGHT GUIDE  
3-040-997-01 PLATE (LCD), GROUND  
3-041-371-01 SHEET (REFLECTOR)  
LED902 8-719-061-16 LED CL-190SR-CD-T (ILLUMINATION) (RED)  
LED903 8-719-038-03 LED CL-190Y-CD-T (ILLUMINATION) (AMBER)  
LED903 8-719-038-07 LED CL-190PG-CD-T (ILLUMINATION)  
(GREEN)  
LED903 8-719-061-16 LED CL-190SR-CD-T (ILLUMINATION) (RED)  
LED904 8-719-038-03 LED CL-190Y-CD-T (ILLUMINATION) (AMBER)  
*
*
*
*
< CAPACITOR >  
LED904 8-719-038-07 LED CL-190PG-CD-T (ILLUMINATION)  
(GREEN)  
LED904 8-719-061-16 LED CL-190SR-CD-T (ILLUMINATION) (RED)  
LED910 8-719-078-19 LED LWA673-R1S2*1 (LCD BACK LIGHT)  
LED911 8-719-078-19 LED LWA673-R1S2*1 (LCD BACK LIGHT)  
LED912 8-719-078-19 LED LWA673-R1S2*1 (LCD BACK LIGHT)  
C951  
C952  
C953  
C954  
C955  
1-164-004-11 CERAMIC CHIP 0.1uF  
1-163-037-11 CERAMIC CHIP 0.022uF 10%  
1-163-251-11 CERAMIC CHIP 100PF  
1-164-004-11 CERAMIC CHIP 0.1uF  
1-164-004-11 CERAMIC CHIP 0.1uF  
10%  
25V  
25V  
50V  
25V  
25V  
5%  
10%  
10%  
C956  
1-164-489-11 CERAMIC CHIP 0.22uF  
< CONNECTOR >  
10%  
16V  
LED913 8-719-078-19 LED LWA673-R1S2*1 (LCD BACK LIGHT)  
LED914 8-719-078-19 LED LWA673-R1S2*1 (LCD BACK LIGHT)  
LED915 8-719-078-19 LED LWA673-R1S2*1 (LCD BACK LIGHT)  
CN901 1-794-065-21 PLUG, CONNECTOR 14P  
< DIODE >  
< SWITCH >  
LSW901 1-771-609-11 SWITCH, TACTILE (WITH LED) (OFF) (GREEN)  
LSW901 1-771-882-21 SWITCH, TACTILE (WITH LED) (OFF) (AMBER)  
LSW901 1-771-883-21 SWITCH, TACTILE (WITH LED) (OFF) (RED)  
LSW902 1-762-617-21 SWITCH, KEY BOARD (WITH LED) (SOURCE)  
(AMBER)  
D901  
D902  
D903  
D904  
D951  
8-719-158-49 DIODE UDZ-TE-17-12B  
8-719-056-82 DIODE UDZ-TE-17-6.2B  
8-719-056-82 DIODE UDZ-TE-17-6.2B  
8-719-056-82 DIODE UDZ-TE-17-6.2B  
8-719-976-99 DIODE UDZ-TE-17-5.1B  
LSW902 1-762-619-21 SWITCH, KEY BOARD (WITH LED) (SOURCE)  
(GREEN)  
D952  
8-719-976-99 DIODE UDZ-TE-17-5.1B  
< IC >  
LSW902 1-771-476-11 SWITCH, KEY BOARD (WITH LED) (SOURCE)  
(RED)  
LSW903 1-762-617-21 SWITCH, KEY BOARD (WITH LED) (SOUND)  
(AMBER)  
IC901  
IC951  
8-759-366-34 IC LC75824E  
8-749-012-25 IC RS-170-TU  
LSW903 1-762-619-21 SWITCH, KEY BOARD (WITH LED) (SOUND)  
(GREEN)  
(REMOTE CONTROL RECEIVER)  
LSW903 1-771-476-11 SWITCH, KEY BOARD (WITH LED) (SOUND)  
(RED)  
LSW904 1-762-617-21 SWITCH, KEY BOARD (WITH LED) (MENU)  
(AMBER)  
< LIQUID CRYSTAL DISPLAY >  
LCD901 1-803-906-11 DISPLAY PANEL, LIQUID CRYSTAL  
(C6400R, C6500R)  
LSW904 1-762-619-21 SWITCH, KEY BOARD (WITH LED) (MENU)  
LCD901 1-803-906-31 DISPLAY PANEL, LIQUID CRYSTAL (C6500RX)  
(GREEN)  
LSW904 1-771-476-11 SWITCH, KEY BOARD (WITH LED) (MENU)  
< LED >  
(RED)  
LSW905 1-762-617-21 SWITCH, KEY BOARD (WITH LED) (PTY DSPL)  
LED901 8-719-038-03 LED CL-190Y-CD-T (ILLUMINATION) (AMBER)  
LED901 8-719-038-07 LED CL-190PG-CD-T (ILLUMINATION)  
(GREEN)  
LED901 8-719-061-16 LED CL-190SR-CD-T (ILLUMINATION) (RED)  
LED902 8-719-038-03 LED CL-190Y-CD-T (ILLUMINATION) (AMBER)  
(AMBER)  
LSW905 1-762-619-21 SWITCH, KEY BOARD (WITH LED) (PTY DSPL)  
(GREEN)  
LSW905 1-771-476-11 SWITCH, KEY BOARD (WITH LED) (PTY DSPL)  
(RED)  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
KEY  
Ref. No.  
Part No.  
Description  
Remark  
Ref. No.  
Part No.  
Description  
Remark  
R909  
R910  
1-216-667-11 METAL CHIP  
1-216-671-11 METAL CHIP  
4.7K  
6.8K  
0.5% 1/10W  
0.5% 1/10W  
LSW906 1-762-617-21 SWITCH, KEY BOARD (WITH LED) (LIST)  
(AMBER)  
LSW906 1-762-619-21 SWITCH, KEY BOARD (WITH LED) (LIST)  
(GREEN)  
LSW906 1-771-476-11 SWITCH, KEY BOARD (WITH LED) (LIST)  
(RED)  
LSW907 1-762-617-21 SWITCH, KEY BOARD (WITH LED) (ENTER)  
(AMBER)  
LSW907 1-762-619-21 SWITCH, KEY BOARD (WITH LED) (ENTER)  
(GREEN)  
R911  
R912  
R913  
R914  
R915  
1-208-806-11 RES, CHIP  
1-216-647-11 METAL CHIP  
1-216-647-11 METAL CHIP  
1-216-647-11 METAL CHIP  
1-216-651-11 METAL CHIP  
10K  
680  
680  
680  
1K  
2%  
1/10W  
0.5% 1/10W  
0.5% 1/10W  
0.5% 1/10W  
0.5% 1/10W  
R916  
R917  
R918  
R919  
R920  
1-216-655-11 METAL CHIP  
1-216-655-11 METAL CHIP  
1-216-659-11 METAL CHIP  
1-216-663-11 METAL CHIP  
1-216-667-11 METAL CHIP  
1.5K  
1.5K  
2.2K  
3.3K  
4.7K  
0.5% 1/10W  
0.5% 1/10W  
0.5% 1/10W  
0.5% 1/10W  
0.5% 1/10W  
LSW907 1-771-476-11 SWITCH, KEY BOARD (WITH LED) (ENTER)  
(RED)  
LSW908 1-771-609-11 SWITCH, TACTILE (WITH LED) (MODE)  
(GREEN)  
LSW908 1-771-882-21 SWITCH, TACTILE (WITH LED) (MODE)  
(AMBER)  
LSW908 1-771-883-21 SWITCH, TACTILE (WITH LED) (MODE) (RED)  
LSW909 1-762-737-11 SWITCH, KEY BOARD (WITH LED) (D-BASS)  
R921  
R921  
R921  
R923  
R923  
1-216-807-11 METAL CHIP  
1-216-810-11 METAL CHIP  
1-216-811-11 METAL CHIP  
1-216-807-11 METAL CHIP  
1-216-811-11 METAL CHIP  
68  
5%  
5%  
5%  
5%  
5%  
1/16W  
(GREEN)  
1/16W  
(RED)  
1/16W  
(AMBER)  
1/16W  
(GREEN)  
1/16W  
120  
150  
68  
LSW910 1-762-617-21 SWITCH, KEY BOARD (WITH LED) (TA)  
(AMBER)  
LSW910 1-762-619-21 SWITCH, KEY BOARD (WITH LED) (TA)  
(GREEN)  
150  
(AMBER)  
LSW910 1-771-476-11 SWITCH, KEY BOARD (WITH LED) (TA) (RED)  
LSW911 1-762-617-21 SWITCH, KEY BOARD (WITH LED) (AF)  
(AMBER)  
LSW911 1-762-619-21 SWITCH, KEY BOARD (WITH LED) (AF)  
(GREEN)  
R923  
R925  
R925  
R925  
R927  
1-216-812-11 METAL CHIP  
1-216-021-00 METAL CHIP  
1-216-029-00 METAL CHIP  
1-216-031-00 METAL CHIP  
1-216-021-00 METAL CHIP  
180  
68  
5%  
5%  
5%  
5%  
5%  
1/16W  
(RED)  
1/10W  
(GREEN)  
1/10W  
(AMBER)  
1/10W  
(RED)  
150  
180  
68  
LSW911 1-771-476-11 SWITCH, KEY BOARD (WITH LED) (AF) (RED)  
LSW912 1-771-609-11 SWITCH, TACTILE (WITH LED) (6) (GREEN)  
LSW912 1-771-882-21 SWITCH, TACTILE (WITH LED) (6) (AMBER)  
LSW912 1-771-883-21 SWITCH, TACTILE (WITH LED) (6) (RED)  
LSW913 1-771-609-11 SWITCH, TACTILE (WITH LED) (5) (GREEN)  
1/10W  
(GREEN)  
LSW913 1-771-882-21 SWITCH, TACTILE (WITH LED) (5) (AMBER)  
LSW913 1-771-883-21 SWITCH, TACTILE (WITH LED) (5) (RED)  
LSW914 1-771-609-11 SWITCH, TACTILE (WITH LED) (4) (GREEN)  
LSW914 1-771-882-21 SWITCH, TACTILE (WITH LED) (4) (AMBER)  
LSW914 1-771-883-21 SWITCH, TACTILE (WITH LED) (4) (RED)  
R927  
R927  
1-216-029-00 METAL CHIP  
1-216-031-00 METAL CHIP  
150  
180  
5%  
5%  
1/10W  
(AMBER)  
1/10W  
(RED)  
1/16W  
1/16W  
1/16W  
(GREEN)  
R931  
R932  
R933  
1-216-813-11 METAL CHIP  
1-216-813-11 METAL CHIP  
1-216-808-11 METAL CHIP  
220  
220  
82  
5%  
5%  
5%  
LSW915 1-771-609-11 SWITCH, TACTILE (WITH LED) (3) (GREEN)  
LSW915 1-771-882-21 SWITCH, TACTILE (WITH LED) (3) (AMBER)  
LSW915 1-771-883-21 SWITCH, TACTILE (WITH LED) (3) (RED)  
LSW916 1-771-609-11 SWITCH, TACTILE (WITH LED) (SHUF 2)  
(GREEN)  
R933  
R933  
1-216-812-11 METAL CHIP  
1-216-813-11 METAL CHIP  
180  
220  
5%  
5%  
1/16W  
(AMBER)  
1/16W  
LSW916 1-771-882-21 SWITCH, TACTILE (WITH LED) (SHUF 2)  
(AMBER)  
(RED)  
R938  
R939  
1-216-809-11 METAL CHIP  
1-216-821-11 METAL CHIP  
100  
1K  
5%  
5%  
1/16W  
1/16W  
(C6500RX)  
1/16W  
LSW916 1-771-883-21 SWITCH, TACTILE (WITH LED) (SHUF 2) (RED)  
LSW917 1-771-609-11 SWITCH, TACTILE (WITH LED) (REP 1)  
(GREEN)  
R951  
1-216-819-11 METAL CHIP  
680  
5%  
LSW917 1-771-882-21 SWITCH, TACTILE (WITH LED) (REP 1)  
(AMBER)  
R952  
R953  
R954  
R955  
R956  
1-216-021-00 METAL CHIP  
1-216-857-11 METAL CHIP  
1-216-049-11 RES, CHIP  
1-216-049-11 RES, CHIP  
1-216-821-11 METAL CHIP  
68  
1M  
1K  
1K  
1K  
5%  
5%  
5%  
5%  
5%  
1/10W  
1/16W  
1/10W  
1/10W  
1/16W  
LSW917 1-771-883-21 SWITCH, TACTILE (WITH LED) (REP 1) (RED)  
< RESISTOR >  
R901  
R902  
R903  
R904  
R905  
1-216-647-11 METAL CHIP  
1-216-647-11 METAL CHIP  
1-216-647-11 METAL CHIP  
1-216-651-11 METAL CHIP  
1-216-655-11 METAL CHIP  
680  
680  
680  
1K  
0.5% 1/10W  
0.5% 1/10W  
0.5% 1/10W  
0.5% 1/10W  
0.5% 1/10W  
R957  
R958  
R970  
R971  
R972  
1-216-851-11 METAL CHIP  
1-216-033-00 METAL CHIP  
1-216-815-11 METAL CHIP  
1-216-815-11 METAL CHIP  
1-216-864-11 METAL CHIP  
330K  
220  
330  
330  
0
5%  
5%  
5%  
5%  
5%  
1/16W  
1/10W  
1/16W  
1/16W  
1/16W  
1.5K  
R906  
R907  
R908  
1-216-655-11 METAL CHIP  
1-216-659-11 METAL CHIP  
1-216-663-11 METAL CHIP  
1.5K  
2.2K  
3.3K  
0.5% 1/10W  
0.5% 1/10W  
0.5% 1/10W  
R973  
R975  
1-216-815-11 METAL CHIP  
1-216-815-11 METAL CHIP  
330  
330  
5%  
5%  
1/16W  
1/16W  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
KEY MAIN  
Ref. No.  
Part No.  
Description  
Remark  
Ref. No.  
Part No.  
Description  
Remark  
R976  
R977  
R980  
1-216-815-11 METAL CHIP  
1-216-815-11 METAL CHIP  
1-216-864-11 METAL CHIP  
330  
330  
0
5%  
5%  
5%  
1/16W  
1/16W  
1/16W  
C96  
C97  
C98  
C101  
1-163-809-11 CERAMIC CHIP 0.047uF 10%  
25V  
25V  
25V  
50V  
50V  
1-164-004-11 CERAMIC CHIP 0.1uF  
1-164-004-11 CERAMIC CHIP 0.1uF  
10%  
10%  
20%  
5%  
1-126-160-11 ELECT  
1uF  
R999  
1-216-864-11 METAL CHIP  
0
5%  
1/16W  
C110  
1-163-251-11 CERAMIC CHIP 100PF  
< ROTARY ENCODER >  
C111  
C113  
C121  
C122  
C123  
1-109-982-11 CERAMIC CHIP 1uF  
1-109-982-11 CERAMIC CHIP 1uF  
1-164-004-11 CERAMIC CHIP 0.1uF  
1-163-037-11 CERAMIC CHIP 0.022uF 10%  
1-163-037-11 CERAMIC CHIP 0.022uF 10%  
10%  
10%  
10%  
10V  
10V  
25V  
25V  
25V  
RE901 1-475-014-12 ENCODER, ROTARY (VOLUME/BASS/TREBLE/  
BALANCE/FADER CONTROL)  
< SWITCH >  
C131  
C141  
C142  
C151  
C152  
1-124-233-11 ELECT  
1-163-251-11 CERAMIC CHIP 100PF  
1-126-160-11 ELECT 1uF  
1-162-970-11 CERAMIC CHIP 0.01uF  
1-124-584-00 ELECT 100uF  
10uF  
20%  
5%  
20%  
10%  
20%  
16V  
50V  
50V  
25V  
10V  
S901  
S902  
S903  
S904  
1-771-884-21 SWITCH, TACTILE (WITH LED)  
(SEEK/AMS - . m)  
1-771-884-21 SWITCH, TACTILE (WITH LED)  
(DISC +, PRST +)  
1-771-884-21 SWITCH, TACTILE (WITH LED)  
(SEEK/AMS + > M)  
1-771-884-21 SWITCH, TACTILE (WITH LED)  
C153  
C156  
C157  
C159  
C161  
1-163-009-11 CERAMIC CHIP 0.001uF 10%  
1-163-017-00 CERAMIC CHIP 0.0047uF 5%  
1-107-823-11 CERAMIC CHIP 0.47uF  
1-162-970-11 CERAMIC CHIP 0.01uF  
50V  
50V  
16V  
25V  
16V  
(DISC -, PRST -)  
**************************************************************  
10%  
10%  
20%  
1-124-233-11 ELECT  
10uF  
*
*
*
A-3294-867-A MAIN BOARD, COMPLETE (C6400R)  
A-3294-868-A MAIN BOARD, COMPLETE (C6500RX)  
A-3294-943-A MAIN BOARD, COMPLETE (C6500R)  
*********************  
C162  
C171  
C172  
1-164-489-11 CERAMIC CHIP 0.22uF  
1-126-163-11 ELECT 4.7uF  
1-163-251-11 CERAMIC CHIP 100PF  
10%  
20%  
5%  
16V  
50V  
50V  
(C6500R, C6500RX)  
*
3-040-996-11 HEAT SINK (2P) (C6400R)  
3-040-996-21 HEAT SINK (2P) (C6500R, C6500RX)  
3-040-998-01 BRACKET (IC)  
3-041-011-01 HEAT SINK (REG)  
7-685-647-79 SCREW +BVTP 3X10 TYPE2 IT-3  
C173  
C174  
1-164-489-11 CERAMIC CHIP 0.22uF  
1-162-919-11 CERAMIC CHIP 22PF  
10%  
5%  
16V  
50V  
*
*
C181  
C182  
C183  
C184  
C191  
1-126-163-11 ELECT  
4.7uF  
20%  
5%  
10%  
50V  
50V  
16V  
50V  
1-163-251-11 CERAMIC CHIP 100PF  
1-164-489-11 CERAMIC CHIP 0.22uF  
1-162-919-11 CERAMIC CHIP 22PF  
7-685-793-09 SCREW +PTT 2.6X8 (S)  
7-685-795-09 SCREW +PTT 2.6X12 (S)  
5%  
1-216-295-00 SHORT  
0
< CAPACITOR/SHORT >  
C192  
C193  
C201  
C210  
C241  
1-216-295-00 SHORT  
1-216-295-00 SHORT  
1-126-160-11 ELECT  
1-163-251-11 CERAMIC CHIP 100PF  
1-163-251-11 CERAMIC CHIP 100PF  
0
0
1uF  
C1  
C3  
C4  
C6  
C7  
1-163-233-11 CERAMIC CHIP 18PF  
1-124-584-00 ELECT 100uF  
1-164-004-11 CERAMIC CHIP 0.1uF  
1-164-004-11 CERAMIC CHIP 0.1uF  
5%  
50V  
10V  
25V  
25V  
16V  
20%  
5%  
5%  
50V  
50V  
50V  
20%  
10%  
10%  
20%  
1-124-589-11 ELECT  
47uF  
C242  
C271  
C272  
1-126-160-11 ELECT  
1-126-163-11 ELECT  
1-163-251-11 CERAMIC CHIP 100PF  
1uF  
4.7uF  
20%  
20%  
5%  
50V  
50V  
50V  
C13  
C14  
C52  
C53  
C54  
1-163-017-00 CERAMIC CHIP 0.0047uF 5%  
50V  
50V  
25V  
50V  
50V  
1-163-021-11 CERAMIC CHIP 0.01uF  
1-164-004-11 CERAMIC CHIP 0.1uF  
1-163-229-11 CERAMIC CHIP 12PF  
1-163-229-11 CERAMIC CHIP 12PF  
10%  
10%  
5%  
(C6500R, C6500RX)  
10%  
5%  
C273  
C274  
1-164-489-11 CERAMIC CHIP 0.22uF  
1-163-235-11 CERAMIC CHIP 22PF  
16V  
50V  
5%  
C281  
C282  
C283  
C284  
C361  
1-126-163-11 ELECT  
4.7uF  
20%  
5%  
10%  
5%  
50V  
50V  
16V  
50V  
25V  
C55  
C56  
C57  
C58  
C59  
1-164-004-11 CERAMIC CHIP 0.1uF  
10%  
20%  
10%  
5%  
25V  
16V  
25V  
50V  
16V  
1-163-251-11 CERAMIC CHIP 100PF  
1-164-489-11 CERAMIC CHIP 0.22uF  
1-162-919-11 CERAMIC CHIP 22PF  
1-164-004-11 CERAMIC CHIP 0.1uF  
1-124-589-11 ELECT  
47uF  
1-164-004-11 CERAMIC CHIP 0.1uF  
1-163-263-11 CERAMIC CHIP 330PF  
1-164-505-11 CERAMIC CHIP 2.2uF  
10%  
C362  
C363  
C364  
C368  
C369  
1-126-157-11 ELECT  
1-164-004-11 CERAMIC CHIP 0.1uF  
1-126-157-11 ELECT 10uF  
1-109-982-11 CERAMIC CHIP 1uF  
1-163-021-11 CERAMIC CHIP 0.01uF  
10uF  
20%  
10%  
20%  
10%  
10%  
16V  
25V  
16V  
10V  
50V  
C60  
C61  
C62  
C63  
C90  
1-163-135-00 CERAMIC CHIP 560PF  
1-164-161-11 CERAMIC CHIP 0.0022uF 10%  
1-163-009-11 CERAMIC CHIP 0.001uF 10%  
1-164-315-11 CERAMIC CHIP 470PF  
1-162-964-11 CERAMIC CHIP 0.001uF 10%  
5%  
50V  
100V  
50V  
50V  
50V  
5%  
C370  
C371  
C372  
C373  
C374  
1-163-021-11 CERAMIC CHIP 0.01uF  
1-163-021-11 CERAMIC CHIP 0.01uF  
1-163-021-11 CERAMIC CHIP 0.01uF  
1-163-021-11 CERAMIC CHIP 0.01uF  
10%  
10%  
10%  
10%  
20%  
50V  
50V  
50V  
50V  
10V  
C91  
C92  
C93  
C94  
C95  
1-162-964-11 CERAMIC CHIP 0.001uF 10%  
1-162-964-11 CERAMIC CHIP 0.001uF 10%  
50V  
50V  
50V  
1-163-133-00 CERAMIC CHIP 470PF  
1-162-915-11 CERAMIC CHIP 10PF  
1-107-823-11 CERAMIC CHIP 0.47uF  
5%  
0.5PF 50V  
10% 16V  
1-124-584-00 ELECT  
100uF  
C375  
1-124-584-00 ELECT  
100uF  
20%  
10V  
56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAIN  
Ref. No.  
Part No.  
Description  
Remark  
Ref. No.  
Part No.  
Description  
< DIODE >  
Remark  
C502  
C503  
C504  
C505  
1-164-004-11 CERAMIC CHIP 0.1uF  
1-164-004-11 CERAMIC CHIP 0.1uF  
1-164-004-11 CERAMIC CHIP 0.1uF  
1-164-004-11 CERAMIC CHIP 0.1uF  
10%  
10%  
10%  
10%  
25V  
25V  
25V  
25V  
D1  
D2  
D90  
D91  
D92  
8-719-073-01 DIODE MA111-TX  
8-719-067-56 DIODE MA112-TX  
8-719-073-01 DIODE MA111-TX  
8-719-073-01 DIODE MA111-TX  
8-719-976-99 DIODE UDZ-TE-17-5.1B  
C506  
C507  
C508  
C509  
C510  
1-163-235-11 CERAMIC CHIP 22PF  
1-163-235-11 CERAMIC CHIP 22PF  
1-165-319-11 CERAMIC CHIP 0.1uF  
1-163-021-11 CERAMIC CHIP 0.01uF  
5%  
5%  
Z%  
10%  
20%  
50V  
50V  
50V  
50V  
10V  
D131  
D301  
D302  
D361  
D362  
8-719-422-12 DIODE UDZ-TE-17-3.9B  
8-719-914-44 DIODE DAP202K-T-146  
8-719-073-01 DIODE MA111-TX  
8-719-034-74 DIODE MA4120-M (TA)  
8-719-158-15 DIODE UDZ-TE-17-5.6B  
1-124-584-00 ELECT  
100uF  
C511  
C512  
C513  
C551  
C552  
1-164-004-11 CERAMIC CHIP 0.1uF  
1-163-133-00 CERAMIC CHIP 470PF  
1-163-125-00 CERAMIC CHIP 220PF  
1-164-222-11 CERAMIC CHIP 0.22uF  
1-164-222-11 CERAMIC CHIP 0.22uF  
10%  
5%  
5%  
25V  
50V  
50V  
25V  
25V  
D501  
D502  
D551  
D552  
D553  
8-719-914-44 DIODE DAP202K-T-146  
8-719-073-01 DIODE MA111-TX  
8-719-158-49 DIODE UDZ-TE-17-12B  
8-719-056-82 DIODE UDZ-TE-17-6.2B  
8-719-056-82 DIODE UDZ-TE-17-6.2B  
C571  
1-162-927-11 CERAMIC CHIP 100PF  
5%  
50V  
(C6500R, C6500RX)  
C601  
C602  
C603  
C611  
1-135-473-21 ELECT  
1-163-251-11 CERAMIC CHIP 100PF  
1-162-927-11 CERAMIC CHIP 100PF  
3300uF  
20%  
5%  
5%  
16V  
50V  
50V  
50V  
D554  
D555  
D556  
D557  
D558  
8-719-056-82 DIODE UDZ-TE-17-6.2B  
8-719-056-82 DIODE UDZ-TE-17-6.2B  
8-719-056-82 DIODE UDZ-TE-17-6.2B  
8-719-056-82 DIODE UDZ-TE-17-6.2B  
8-719-056-82 DIODE UDZ-TE-17-6.2B  
1-126-160-11 ELECT  
1uF  
20%  
C612  
C614  
C616  
C617  
C621  
C622  
1-126-160-11 ELECT  
1-126-157-11 ELECT  
1-107-823-11 CERAMIC CHIP 0.47uF  
1-136-165-00 MYLAR  
1-124-589-11 ELECT  
1-126-160-11 ELECT  
1uF  
10uF  
20%  
20%  
10%  
5%  
20%  
20%  
50V  
16V  
16V  
50V  
16V  
50V  
D559  
D560  
D561  
D562  
D563  
D564  
D571  
8-719-056-82 DIODE UDZ-TE-17-6.2B  
8-719-056-82 DIODE UDZ-TE-17-6.2B  
8-719-056-93 DIODE UDZ-TE-17-18B  
8-719-056-82 DIODE UDZ-TE-17-6.2B  
8-719-109-97 DIODE RD6.8ESB2  
8-719-109-97 DIODE RD6.8ESB2  
0.1uF  
47uF  
1uF  
C623  
C625  
C631  
C632  
C641  
C653  
1-109-982-11 CERAMIC CHIP 1uF  
1-109-982-11 CERAMIC CHIP 1uF  
1-164-222-11 CERAMIC CHIP 0.22uF  
1-164-222-11 CERAMIC CHIP 0.22uF  
1-162-964-11 CERAMIC CHIP 0.001uF 10%  
1-163-021-11 CERAMIC CHIP 0.01uF  
10%  
10%  
10V  
10V  
25V  
25V  
50V  
50V  
8-719-073-01 DIODE MA111-TX (C6500R, C6500RX)  
D601  
D602  
D603  
D604  
D605  
8-719-049-38 DIODE 1N5404TU  
8-719-056-93 DIODE UDZ-TE-17-18B  
8-719-056-93 DIODE UDZ-TE-17-18B  
8-719-056-82 DIODE UDZ-TE-17-6.2B  
8-719-056-93 DIODE UDZ-TE-17-18B (C6500R, C6500RX)  
10%  
C654  
C655  
C661  
C671  
C672  
1-125-710-11 DOUBLE LAYER 0.1F  
1-124-584-00 ELECT  
1-109-982-11 CERAMIC CHIP 1uF  
1-126-157-11 ELECT  
1-126-157-11 ELECT  
5.5V  
10V  
10V  
16V  
16V  
100uF  
20%  
10%  
20%  
20%  
D611  
D612  
D613  
D614  
D615  
8-719-079-55 DIODE PTZ-TE25-22  
8-719-079-55 DIODE PTZ-TE25-22  
8-719-079-55 DIODE PTZ-TE25-22  
8-719-079-55 DIODE PTZ-TE25-22  
8-719-079-55 DIODE PTZ-TE25-22  
10uF  
10uF  
C673  
C674  
C675  
C676  
C682  
1-126-157-11 ELECT  
1-124-233-11 ELECT  
1-124-233-11 ELECT  
1-126-157-11 ELECT  
10uF  
10uF  
10uF  
10uF  
20%  
20%  
20%  
20%  
10%  
16V  
16V  
16V  
16V  
50V  
D616  
D617  
D618  
D621  
D622  
D623  
8-719-079-55 DIODE PTZ-TE25-22  
8-719-079-55 DIODE PTZ-TE25-22  
8-719-079-55 DIODE PTZ-TE25-22  
8-719-422-12 DIODE UDZ-TE-17-3.9B  
8-719-073-01 DIODE MA111-TX  
8-719-158-15 DIODE UDZ-TE-17-5.6B  
1-163-021-11 CERAMIC CHIP 0.01uF  
C701  
C702  
C703  
C704  
C705  
1-162-970-11 CERAMIC CHIP 0.01uF  
1-164-004-11 CERAMIC CHIP 0.1uF  
1-164-227-11 CERAMIC CHIP 0.022uF 10%  
1-165-319-11 CERAMIC CHIP 0.1uF  
10%  
10%  
25V  
25V  
25V  
50V  
16V  
D624  
D631  
D653  
D661  
D662  
8-719-158-15 DIODE UDZ-TE-17-5.6B  
8-719-423-26 DIODE MA8110-H  
8-719-073-01 DIODE MA111-TX  
8-719-073-01 DIODE MA111-TX  
8-719-420-14 DIODE MA8082-M (TX)  
1-126-935-11 ELECT  
470uF  
20%  
< CONNECTOR >  
CN301 1-764-617-12 PIN, CONNECTOR (PC BOARD) 30P  
CN500 1-784-456-11 CONNECTOR, FFC/FPC 14P  
CN601 1-774-701-11 PIN, CONNECTOR 16P  
D671  
D672  
D673  
D674  
D675  
8-719-053-18 DIODE 1SR154-400TE-25  
8-719-053-18 DIODE 1SR154-400TE-25  
8-719-053-18 DIODE 1SR154-400TE-25  
8-719-053-18 DIODE 1SR154-400TE-25  
8-719-067-56 DIODE MA112-TX  
CN701 1-580-907-31 PLUG, CONNECTOR (BUS CONTROL IN)  
< JACK >  
CNJ151 1-774-699-12 JACK, PIN 4P (BUS AUDIO IN, AUDIO OUT)  
D676  
D677  
D701  
D702  
8-719-073-01 DIODE MA111-TX  
8-719-073-01 DIODE MA111-TX  
8-719-978-69 DIODE UDZ-TE-17-16B  
8-719-017-62 DIODE MA8068-L-TX  
(C6400R)  
CNJ151 1-774-700-11 JACK, PIN 6P (BUS AUDIO IN,  
AUDIO OUT REAR/FRONT) (C6500R, C6500RX)  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAIN  
Ref. No.  
D703  
Part No.  
Description  
Remark  
Ref. No.  
Part No.  
Description  
Remark  
8-719-056-82 DIODE UDZ-TE-17-6.2B  
Q121  
Q131  
8-729-920-21 TRANSISTOR DTC314TK-T-146  
8-729-921-25 TRANSISTOR FMC2-T148  
D704  
D705  
D706  
D708  
D709  
8-719-056-93 DIODE UDZ-TE-17-18B  
8-719-056-93 DIODE UDZ-TE-17-18B  
8-719-072-70 DIODE MA2ZD14001S0  
8-719-073-01 DIODE MA111-TX  
8-719-073-01 DIODE MA111-TX  
Q171  
Q181  
Q250  
Q271  
Q281  
8-729-920-21 TRANSISTOR DTC314TK-T-146  
8-729-920-21 TRANSISTOR DTC314TK-T-146  
8-729-921-25 TRANSISTOR FMC2-T148  
8-729-920-21 TRANSISTOR DTC314TK-T-146  
8-729-920-21 TRANSISTOR DTC314TK-T-146  
D710  
8-719-073-01 DIODE MA111-TX  
< COIL >  
Q361  
Q362  
Q363  
Q551  
Q571  
8-729-019-00 TRANSISTOR 2SD2394-G  
8-729-019-00 TRANSISTOR 2SD2394-G  
8-729-921-25 TRANSISTOR FMC2-T148  
8-729-921-25 TRANSISTOR FMC2-T148  
8-729-120-28 TRANSISTOR 2SC2412K-T-146-QR  
FB362 1-414-233-22 INDUCTOR CHIP 0uH  
FB501 1-414-233-22 INDUCTOR CHIP 0uH  
(C6500R, C6500RX)  
< FUSE >  
Q621  
Q622  
Q631  
Q633  
Q651  
8-729-027-23 TRANSISTOR DTA114EKA-T146  
8-729-021-94 FET 2SK1657-T1B  
8-729-423-99 TRANSISTOR 2SD2137-OP-TA  
8-729-921-25 TRANSISTOR FMC2-T148  
8-729-027-23 TRANSISTOR DTA114EKA-T146  
FU601 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A  
< IC >  
IC51  
IC90  
8-759-650-68 IC SAA6588T/V2-118  
8-759-909-71 IC BA4558F-E2  
Q652  
Q661  
Q701  
Q704  
Q705  
8-729-027-23 TRANSISTOR DTA114EKA-T146  
8-729-120-28 TRANSISTOR 2SC2412K-T-146-QR  
8-729-900-53 TRANSISTOR DTC114EKA-T146  
8-729-027-23 TRANSISTOR DTA114EKA-T146  
8-729-027-23 TRANSISTOR DTA114EKA-T146  
IC151  
IC501  
IC611  
8-759-653-27 IC TDA7402TR  
8-759-663-56 IC MB90574PMT-G-266-BND  
8-759-663-88 IC TA8268H  
IC652  
IC671  
IC701  
8-759-574-61 IC XC61AN4302MR  
8-759-661-47 IC BA4908-V3  
8-759-449-89 IC BA8270F-E2  
Q706  
8-729-120-28 TRANSISTOR 2SC2412K-T-146-QR  
< RESISTOR >  
< JACK >  
R1  
R4  
R5  
R6  
R7  
1-216-295-00 SHORT  
0
J1  
J501  
1-764-808-21 JACK (ANT) (FM/AM ANTENNA)  
1-566-822-41 JACK (REMOTE IN)  
1-216-025-00 RES, CHIP  
1-216-025-00 RES, CHIP  
1-216-025-00 RES, CHIP  
1-216-025-00 RES, CHIP  
100  
100  
100  
100  
5%  
5%  
5%  
5%  
1/10W  
1/10W  
1/10W  
1/10W  
< RESISTOR >  
JC1  
JC2  
JC4  
JC5  
JC16  
1-216-296-00 SHORT  
1-216-296-00 SHORT  
1-216-296-00 SHORT  
1-216-296-00 SHORT  
1-216-295-00 SHORT  
0
0
0
0
0
R8  
R9  
R12  
R20  
R53  
1-216-295-00 SHORT  
0
1-216-041-00 METAL CHIP  
1-216-837-11 METAL CHIP  
1-216-057-00 METAL CHIP  
1-216-853-11 METAL CHIP  
470  
22K  
2.2K  
470K  
5%  
5%  
5%  
5%  
1/10W  
1/16W  
1/10W  
1/16W  
JC31  
JC50  
JC54  
JC90  
1-216-295-00 SHORT  
1-216-295-00 SHORT  
1-216-295-00 SHORT  
1-216-295-00 SHORT  
0
0
0
0
0
R54  
R55  
R56  
R57  
R58  
1-216-821-11 METAL CHIP  
1-216-061-00 METAL CHIP  
1-216-817-11 METAL CHIP  
1-216-809-11 METAL CHIP  
1-216-025-00 RES, CHIP  
1K  
5%  
5%  
5%  
5%  
5%  
1/16W  
1/10W  
1/16W  
1/16W  
1/10W  
3.3K  
470  
100  
100  
JC191 1-216-295-00 SHORT  
JC192 1-216-295-00 SHORT  
JC193 1-216-295-00 SHORT  
JC194 1-216-295-00 SHORT  
JC301 1-216-864-11 METAL CHIP  
JC601 1-216-864-11 METAL CHIP  
0
0
0
0
0
R59  
R60  
R90  
R91  
R92  
1-216-001-00 METAL CHIP  
1-216-797-11 METAL CHIP  
1-216-825-11 METAL CHIP  
1-216-825-11 METAL CHIP  
1-216-025-00 RES, CHIP  
10  
10  
2.2K  
2.2K  
100  
5%  
5%  
5%  
5%  
5%  
1/10W  
1/16W  
1/16W  
1/16W  
1/10W  
5%  
5%  
1/16W  
1/16W  
JC671 1-216-295-00 SHORT  
JC673 1-216-864-11 METAL CHIP  
0
0
R93  
R94  
R95  
R96  
R97  
1-216-845-11 METAL CHIP  
1-216-829-11 METAL CHIP  
1-216-121-00 RES, CHIP  
1-216-025-00 RES, CHIP  
1-216-833-11 RES, CHIP  
100K  
4.7K  
1M  
100  
10K  
5%  
5%  
5%  
5%  
5%  
1/16W  
1/16W  
1/10W  
1/10W  
1/16W  
5%  
1/16W  
< COIL >  
L601  
L671  
1-419-476-21 COIL, CHOKE (2000) 250uH  
1-410-989-11 INDUCTOR CHIP 0.47uH  
R98  
1-216-833-11 RES, CHIP  
1-216-295-00 SHORT  
1-216-864-11 METAL CHIP  
1-216-841-11 METAL CHIP  
1-216-049-11 RES, CHIP  
10K  
0
0
47K  
1K  
5%  
1/16W  
R108  
R111  
R112  
R121  
< TRANSISTOR >  
5%  
5%  
5%  
1/16W  
1/16W  
1/10W  
Q1  
Q90  
Q111  
8-729-120-28 TRANSISTOR 2SC2412K-T-146-QR  
8-729-900-53 TRANSISTOR DTC114EKA-T146  
8-729-920-21 TRANSISTOR DTC314TK-T-146  
R122  
1-216-085-00 METAL CHIP  
33K  
5%  
1/10W  
58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAIN  
Ref. No.  
Part No.  
Description  
Remark  
Ref. No.  
R551  
Part No.  
Description  
Remark  
R131  
R132  
R141  
R142  
1-216-037-00 METAL CHIP  
1-216-045-00 METAL CHIP  
1-216-025-00 RES, CHIP  
1-216-073-00 METAL CHIP  
330  
680  
100  
10K  
5%  
5%  
5%  
5%  
1/10W  
1/10W  
1/10W  
1/10W  
1-249-413-11 CARBON  
470  
5%  
1/4W  
(C6500RX)  
R552  
R553  
R554  
R555  
R556  
1-216-025-00 RES, CHIP  
1-216-025-00 RES, CHIP  
1-216-025-00 RES, CHIP  
1-216-025-00 RES, CHIP  
1-216-025-00 RES, CHIP  
100  
100  
100  
100  
100  
5%  
5%  
5%  
5%  
5%  
1/10W  
1/10W  
1/10W  
1/10W  
1/10W  
R152  
R153  
R154  
R156  
R171  
1-216-841-11 METAL CHIP  
1-216-025-00 RES, CHIP  
1-216-025-00 RES, CHIP  
1-216-809-11 METAL CHIP  
1-216-033-00 METAL CHIP  
47K  
100  
100  
100  
220  
5%  
5%  
5%  
5%  
5%  
1/16W  
1/10W  
1/10W  
1/16W  
1/10W  
R557  
R558  
R559  
R560  
R561  
1-216-025-00 RES, CHIP  
1-216-025-00 RES, CHIP  
1-216-025-00 RES, CHIP  
1-216-025-00 RES, CHIP  
1-208-806-11 RES, CHIP  
100  
100  
100  
100  
10K  
5%  
5%  
5%  
5%  
1/10W  
1/10W  
1/10W  
1/10W  
R172  
R173  
R181  
R182  
R183  
1-216-081-00 METAL CHIP  
1-216-089-00 RES, CHIP  
1-216-033-00 METAL CHIP  
1-216-081-00 METAL CHIP  
1-216-089-00 RES, CHIP  
22K  
47K  
220  
22K  
47K  
5%  
5%  
5%  
5%  
5%  
1/10W  
1/10W  
1/10W  
1/10W  
1/10W  
0.5% 1/10W  
R562  
R563  
R564  
R565  
R567  
1-208-806-11 RES, CHIP  
1-216-845-11 METAL CHIP  
1-216-845-11 METAL CHIP  
1-216-025-00 RES, CHIP  
1-249-411-11 CARBON  
10K  
0.5% 1/10W  
100K  
100K  
100  
5%  
5%  
5%  
5%  
1/16W  
1/16W  
1/10W  
1/4W  
R208  
R241  
R242  
R271  
R272  
1-216-295-00 SHORT  
0
1-216-025-00 RES, CHIP  
1-216-073-00 METAL CHIP  
1-216-033-00 METAL CHIP  
1-216-081-00 METAL CHIP  
100  
10K  
220  
22K  
5%  
5%  
5%  
5%  
1/10W  
1/10W  
1/10W  
1/10W  
330  
R571  
1-216-845-11 METAL CHIP  
100K  
5%  
1/16W  
(C64OOR)  
1/16W  
1/16W  
1/10W  
R273  
R281  
R282  
R283  
R361  
1-216-089-00 RES, CHIP  
1-216-033-00 METAL CHIP  
1-216-081-00 METAL CHIP  
1-216-089-00 RES, CHIP  
1-216-041-00 METAL CHIP  
47K  
220  
22K  
47K  
470  
5%  
5%  
5%  
5%  
5%  
1/10W  
1/10W  
1/10W  
1/10W  
1/10W  
R572  
R573  
R600  
R601  
R603  
1-216-809-11 METAL CHIP  
1-216-809-11 METAL CHIP  
1-216-097-00 RES, CHIP  
1-216-073-00 METAL CHIP  
1-216-073-00 METAL CHIP  
100  
100  
100K  
10K  
10K  
5%  
5%  
5%  
5%  
5%  
1/10W  
1/10W  
R362  
R363  
R364  
R504  
R505  
1-216-041-00 METAL CHIP  
1-216-041-00 METAL CHIP  
1-216-041-00 METAL CHIP  
1-216-057-00 METAL CHIP  
1-216-057-00 METAL CHIP  
470  
470  
470  
2.2K  
2.2K  
5%  
5%  
5%  
5%  
5%  
1/10W  
1/10W  
1/10W  
1/10W  
1/10W  
R611  
R612  
R621  
R622  
R624  
1-216-833-11 RES, CHIP  
1-216-073-00 METAL CHIP  
1-216-805-11 METAL CHIP  
1-216-864-11 METAL CHIP  
1-216-295-00 SHORT  
10K  
10K  
47  
0
5%  
5%  
5%  
5%  
1/16W  
1/10W  
1/16W  
1/16W  
0
R506  
R507  
R509  
R520  
R522  
1-216-057-00 METAL CHIP  
1-216-073-00 METAL CHIP  
1-216-097-00 RES, CHIP  
1-216-097-00 RES, CHIP  
1-216-097-00 RES, CHIP  
2.2K  
10K  
100K  
100K  
100K  
5%  
5%  
5%  
5%  
5%  
1/10W  
1/10W  
1/10W  
1/10W  
1/10W  
R626  
R631  
R632  
R636  
R641  
1-216-861-11 METAL CHIP  
1-249-385-11 CARBON  
1-249-385-11 CARBON  
1-216-037-00 METAL CHIP  
1-216-849-11 METAL CHIP  
2.2M  
2.2  
2.2  
330  
220K  
5%  
5%  
5%  
5%  
5%  
1/16W  
1/6W  
1/6W  
1/10W  
1/16W  
R523  
R524  
R525  
R526  
R529  
1-216-845-11 METAL CHIP  
1-216-073-00 METAL CHIP  
1-216-073-00 METAL CHIP  
1-216-097-00 RES, CHIP  
1-216-049-11 RES, CHIP  
100K  
10K  
10K  
100K  
1K  
5%  
5%  
5%  
5%  
5%  
1/16W  
1/10W  
1/10W  
1/10W  
1/10W  
R642  
R651  
R652  
R653  
R654  
1-216-853-11 METAL CHIP  
1-216-113-00 METAL CHIP  
1-216-845-11 METAL CHIP  
1-208-806-11 RES, CHIP  
1-216-833-11 RES, CHIP  
470K  
470K  
100K  
10K  
5%  
5%  
5%  
1/16W  
1/10W  
1/16W  
0.5% 1/10W  
5%  
10K  
1/16W  
R531  
R532  
R533  
R534  
R535  
1-216-839-11 METAL CHIP  
1-216-833-11 RES, CHIP  
1-216-833-11 RES, CHIP  
1-216-097-00 RES, CHIP  
1-216-845-11 METAL CHIP  
33K  
5%  
1/16W  
R655  
R656  
R661  
R662  
R663  
1-216-809-11 METAL CHIP  
1-216-809-11 METAL CHIP  
1-249-421-11 CARBON  
1-216-081-00 METAL CHIP  
1-216-841-11 METAL CHIP  
100  
100  
2.2K  
22K  
47K  
5%  
5%  
5%  
5%  
5%  
1/16W  
1/16W  
1/4W  
1/10W  
1/16W  
(C6500R, C6500RX)  
5% 1/16W  
(C6500R, C6500RX)  
5% 1/16W  
(C6500R, C6500RX)  
5% 1/10W  
(C6500R, C6500RX)  
10K  
10K  
100K  
100K  
R664  
R682  
R701  
R702  
R703  
1-216-841-11 METAL CHIP  
1-216-089-00 RES, CHIP  
1-216-805-11 METAL CHIP  
1-216-073-00 METAL CHIP  
1-216-025-00 RES, CHIP  
47K  
47K  
47  
10K  
100  
5%  
5%  
5%  
5%  
5%  
1/16W  
1/10W  
1/16W  
1/10W  
1/10W  
5%  
1/16W  
R537  
R538  
R539  
R540  
R542  
1-216-097-00 RES, CHIP  
1-216-097-00 RES, CHIP  
1-216-097-00 RES, CHIP  
1-216-097-00 RES, CHIP  
1-216-089-00 RES, CHIP  
100K  
100K  
100K  
100K  
47K  
5%  
5%  
5%  
5%  
5%  
1/10W  
1/10W  
1/10W  
1/10W  
1/10W  
R704  
R707  
R713  
R714  
R715  
1-216-809-11 METAL CHIP  
1-216-065-00 RES, CHIP  
1-216-841-11 METAL CHIP  
1-216-841-11 METAL CHIP  
1-216-845-11 METAL CHIP  
100  
5%  
5%  
5%  
5%  
5%  
1/16W  
1/10W  
1/16W  
1/16W  
1/16W  
4.7K  
47K  
47K  
100K  
R545  
R546  
R547  
R551  
1-216-097-00 RES, CHIP  
1-216-097-00 RES, CHIP  
1-216-097-00 RES, CHIP  
1-249-409-11 CARBON  
100K  
100K  
100K  
220  
5%  
5%  
5%  
5%  
1/10W  
1/10W  
1/10W  
1/4W  
R716  
1-216-809-11 METAL CHIP  
100  
5%  
1/16W  
(C6400R, C6500R)  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ver 1.2  
MAIN SENSOR SERVO  
Ref. No.  
Part No.  
Description  
< SWITCH >  
Remark  
Ref. No.  
Part No.  
Description  
Remark  
C325  
C326  
C327  
1-110-563-11 CERAMIC CHIP 0.068uF 10%  
1-162-968-11 CERAMIC CHIP 0.0047uF 10%  
1-109-982-11 CERAMIC CHIP 1uF  
16V  
50V  
10V  
SW503 1-692-431-21 SWITCH, TACTILE (RESET)  
10%  
SW504 1-771-540-11 SWITCH, PUSH (1KEY) (NOSE DETECT)  
C328  
C329  
C330  
C331  
C333  
1-162-966-11 CERAMIC CHIP 0.0022uF 10%  
1-164-227-11 CERAMIC CHIP 0.022uF 10%  
50V  
25V  
25V  
16V  
16V  
< THERMISTOR >  
1-162-970-11 CERAMIC CHIP 0.01uF  
1-107-826-11 CERAMIC CHIP 0.1uF  
1-107-826-11 CERAMIC CHIP 0.1uF  
10%  
10%  
10%  
TH701 1-803-350-21 THERMISTOR, POSITIVE  
< TUNER >  
C334  
C335  
C336  
C337  
C338  
1-164-004-11 CERAMIC CHIP 0.1uF  
1-164-004-11 CERAMIC CHIP 0.1uF  
1-162-970-11 CERAMIC CHIP 0.01uF  
1-164-004-11 CERAMIC CHIP 0.1uF  
1-164-004-11 CERAMIC CHIP 0.1uF  
10%  
10%  
10%  
10%  
10%  
25V  
25V  
25V  
25V  
25V  
TU1  
A-3220-812-A TUNER UNIT (TUX-020)  
< VIBRATOR >  
X51  
X501  
X502  
1-579-242-41 VIBRATOR, CRYSTAL (4.332MHz)  
1-767-833-21 VIBRATOR, CERAMIC (3.68MHz)  
1-567-098-41 VIBRATOR, CRYSTAL (32.768kHz)  
C339  
C340  
C341  
C342  
C343  
1-162-970-11 CERAMIC CHIP 0.01uF  
1-162-918-11 CERAMIC CHIP 18PF  
1-162-918-11 CERAMIC CHIP 18PF  
1-162-970-11 CERAMIC CHIP 0.01uF  
1-162-970-11 CERAMIC CHIP 0.01uF  
10%  
5%  
5%  
10%  
10%  
25V  
50V  
50V  
25V  
25V  
**************************************************************  
A-3326-034-A SENSOR BOARD, COMPLETE  
************************  
C344  
C345  
C346  
C347  
C348  
1-104-852-11 TANTALUM CHIP 22uF  
1-162-970-11 CERAMIC CHIP 0.01uF  
1-104-852-11 TANTALUM CHIP 22uF  
1-162-970-11 CERAMIC CHIP 0.01uF  
1-107-826-11 CERAMIC CHIP 0.1uF  
20%  
10%  
20%  
10%  
10%  
10V  
25V  
6.3V  
25V  
16V  
For the parts on the SENSOR board, replace the entire mounted board.  
**************************************************************  
*
A-3326-036-A SERVO BOARD, COMPLETE  
**********************  
C349  
C350  
C351  
C352  
C353  
1-107-826-11 CERAMIC CHIP 0.1uF  
1-107-826-11 CERAMIC CHIP 0.1uF  
1-104-852-11 TANTALUM CHIP 22uF  
1-107-826-11 CERAMIC CHIP 0.1uF  
1-107-826-11 CERAMIC CHIP 0.1uF  
10%  
10%  
20%  
10%  
10%  
16V  
16V  
10V  
16V  
16V  
< CAPACITOR >  
C11  
1-162-964-11 CERAMIC CHIP 0.001uF 10%  
1-104-543-11 FILM CHIP  
1-135-259-11 TANTALUM CHIP 10uF  
1-162-970-11 CERAMIC CHIP 0.01uF  
1-107-826-11 CERAMIC CHIP 0.1uF  
50V  
50V  
6.3V  
25V  
16V  
C101  
C102  
C103  
C104  
0.0022uF 5%  
20%  
10%  
10%  
C356  
C357  
C358  
C359  
C361  
1-162-927-11 CERAMIC CHIP 100PF  
1-162-927-11 CERAMIC CHIP 100PF  
1-162-927-11 CERAMIC CHIP 100PF  
1-162-923-11 CERAMIC CHIP 47PF  
1-135-259-11 TANTALUM CHIP 10uF  
5%  
5%  
5%  
5%  
20%  
50V  
50V  
50V  
50V  
6.3V  
C105  
C106  
C107  
C108  
C109  
1-107-826-11 CERAMIC CHIP 0.1uF  
1-135-181-21 TANTALUM CHIP 4.7uF  
1-162-970-11 CERAMIC CHIP 0.01uF  
1-162-970-11 CERAMIC CHIP 0.01uF  
1-135-181-21 TANTALUM CHIP 4.7uF  
10%  
20%  
10%  
10%  
20%  
16V  
6.3V  
25V  
25V  
6.3V  
C362  
C402  
C403  
C501  
C503  
1-107-826-11 CERAMIC CHIP 0.1uF  
1-162-970-11 CERAMIC CHIP 0.01uF  
1-107-826-11 CERAMIC CHIP 0.1uF  
1-162-927-11 CERAMIC CHIP 100PF  
1-107-826-11 CERAMIC CHIP 0.1uF  
10%  
10%  
10%  
5%  
16V  
25V  
16V  
50V  
16V  
C201  
C202  
C301  
C302  
C304  
1-104-543-11 FILM CHIP  
0.0022uF 5%  
50V  
6.3V  
16V  
16V  
50V  
1-135-259-11 TANTALUM CHIP 10uF  
1-107-826-11 CERAMIC CHIP 0.1uF  
1-107-826-11 CERAMIC CHIP 0.1uF  
1-162-927-11 CERAMIC CHIP 100PF  
20%  
10%  
10%  
5%  
10%  
C504  
C505  
C506  
C510  
C511  
1-107-826-11 CERAMIC CHIP 0.1uF  
1-107-826-11 CERAMIC CHIP 0.1uF  
1-104-852-11 TANTALUM CHIP 22uF  
1-115-467-11 CERAMIC CHIP 0.22uF  
1-107-826-11 CERAMIC CHIP 0.1uF  
10%  
10%  
20%  
10%  
10%  
16V  
16V  
10V  
10V  
16V  
C305  
C306  
C307  
C308  
C309  
1-162-970-11 CERAMIC CHIP 0.01uF  
1-107-823-11 CERAMIC CHIP 0.47uF  
1-107-826-11 CERAMIC CHIP 0.1uF  
1-162-927-11 CERAMIC CHIP 100PF  
10%  
10%  
10%  
5%  
25V  
16V  
16V  
50V  
50V  
C512  
C513  
C514  
C515  
C516  
1-107-826-11 CERAMIC CHIP 0.1uF  
1-107-826-11 CERAMIC CHIP 0.1uF  
1-115-467-11 CERAMIC CHIP 0.22uF  
1-107-826-11 CERAMIC CHIP 0.1uF  
1-107-826-11 CERAMIC CHIP 0.1uF  
10%  
10%  
10%  
10%  
10%  
16V  
16V  
10V  
16V  
16V  
1-162-968-11 CERAMIC CHIP 0.0047uF 10%  
C310  
C311  
C314  
C315  
C316  
1-107-823-11 CERAMIC CHIP 0.47uF  
1-164-245-11 CERAMIC CHIP 0.015uF 10%  
1-107-826-11 CERAMIC CHIP 0.1uF  
1-109-982-11 CERAMIC CHIP 1uF  
1-107-826-11 CERAMIC CHIP 0.1uF  
10%  
16V  
25V  
16V  
10V  
16V  
10%  
10%  
10%  
< CONNECTOR >  
CN101 1-764-616-12 HOUSING, CONNECTOR (PC BOARD) 30P  
CN102 1-573-929-21 CONNECTOR, FFC/FPC (ZIF) 20P  
CN103 1-764-439-21 CONNECTOR, FPC 11P  
C317  
C318  
C319  
C320  
C321  
1-107-826-11 CERAMIC CHIP 0.1uF  
1-104-852-11 TANTALUM CHIP 22uF  
1-104-852-11 TANTALUM CHIP 22uF  
1-164-227-11 CERAMIC CHIP 0.022uF 10%  
1-162-969-11 CERAMIC CHIP 0.0068uF 10%  
10%  
20%  
20%  
16V  
6.3V  
6.3V  
25V  
25V  
< DIODE >  
D401  
D501  
8-719-157-93 DIODE DTZ-TT11-3.0B  
8-719-988-61 DIODE 1SS355TE-17  
C322  
C324  
1-162-964-11 CERAMIC CHIP 0.001uF 10%  
50V  
16V  
1-107-826-11 CERAMIC CHIP 0.1uF  
10%  
60  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVO  
Ref. No.  
Part No.  
Description  
Remark  
Ref. No.  
Part No.  
Description  
Remark  
< FERRITE BEAD >  
R324  
R325  
R327  
R328  
R329  
1-216-827-11 METAL CHIP  
1-216-821-11 METAL CHIP  
1-216-821-11 METAL CHIP  
1-216-811-11 METAL CHIP  
1-216-819-11 METAL CHIP  
3.3K  
1K  
1K  
150  
680  
5%  
1/16W  
1/16W  
1/16W  
1/16W  
1/16W  
5%  
5%  
5%  
5%  
FB301 1-414-235-22 FERRITE BEAD INDUCTOR CHIP  
FB302 1-414-760-21 FERRITE BEAD INDUCTOR CHIP  
0uH  
0uH  
< IC >  
R330  
R331  
R332  
R333  
R334  
1-216-853-11 METAL CHIP  
1-216-809-11 METAL CHIP  
1-216-809-11 METAL CHIP  
1-216-819-11 METAL CHIP  
1-216-809-11 METAL CHIP  
470K  
100  
100  
680  
100  
5%  
5%  
5%  
5%  
5%  
1/16W  
1/16W  
1/16W  
1/16W  
1/16W  
IC101  
IC301  
IC302  
IC303  
IC304  
8-759-571-84 IC PCM1718E/2K  
8-752-384-47 IC CXD2652AR  
8-752-080-95 IC CXA2523AR  
8-759-430-25 IC BH6511FS-E2  
8-759-096-87 IC TC7WU04FU (TE12R)  
R335  
R336  
R337  
R338  
R339  
1-216-815-11 METAL CHIP  
1-216-853-11 METAL CHIP  
1-216-853-11 METAL CHIP  
1-216-833-11 RES, CHIP  
1-216-827-11 METAL CHIP  
330  
5%  
5%  
5%  
5%  
5%  
1/16W  
1/16W  
1/16W  
1/16W  
1/16W  
IC305  
IC306  
IC307  
IC401  
IC501  
8-759-040-83 IC BA6287F  
470K  
470K  
10K  
8-759-058-62 IC TC7S08FU (TE85R)  
8-759-368-16 IC MN41V4400TT-08S  
8-759-909-71 IC BA4558F-E2  
8-752-909-21 IC CXP84340-217Q  
3.3K  
R340  
R341  
R342  
R343  
R344  
1-216-843-11 METAL CHIP  
1-216-837-11 METAL CHIP  
1-216-833-11 RES, CHIP  
1-216-827-11 METAL CHIP  
1-216-833-11 RES, CHIP  
68K  
22K  
10K  
3.3K  
10K  
5%  
5%  
5%  
5%  
5%  
1/16W  
1/16W  
1/16W  
1/16W  
1/16W  
IC502  
IC503  
8-759-238-47 IC TC74HCT7007AF (EL)  
8-759-238-47 IC TC74HCT7007AF (EL)  
< COIL >  
L101  
L102  
L301  
L302  
L303  
1-412-058-11 INDUCTOR CHIP 10uH  
1-412-058-11 INDUCTOR CHIP 10uH  
1-412-058-11 INDUCTOR CHIP 10uH  
1-412-058-11 INDUCTOR CHIP 10uH  
1-412-039-51 INDUCTOR CHIP 100uH  
R345  
R346  
R347  
R348  
R349  
1-216-827-11 METAL CHIP  
1-216-841-11 METAL CHIP  
1-216-833-11 RES, CHIP  
1-218-863-11 RES, CHIP  
1-216-025-00 RES, CHIP  
3.3K  
47K  
10K  
4.7K  
100  
5%  
5%  
5%  
1/16W  
1/16W  
1/16W  
0.5% 1/16W  
5%  
1/10W  
L304  
L305  
L306  
L501  
1-412-039-51 INDUCTOR CHIP 100uH  
1-412-039-51 INDUCTOR CHIP 100uH  
1-412-039-51 INDUCTOR CHIP 100uH  
1-412-058-11 INDUCTOR CHIP 10uH  
R350  
R351  
R352  
R353  
R354  
1-216-142-00 RES, CHIP  
1-218-855-11 RES, CHIP  
1-218-855-11 RES, CHIP  
1-218-855-11 RES, CHIP  
1-216-857-11 METAL CHIP  
4.7  
5%  
1/8W  
2.2K  
2.2K  
2.2K  
1M  
0.5% 1/16W  
0.5% 1/16W  
0.5% 1/16W  
5%  
1/16W  
< TRANSISTOR >  
R355  
R356  
R357  
R359  
R401  
1-216-833-11 RES, CHIP  
1-216-833-11 RES, CHIP  
1-216-017-00 RES, CHIP  
1-216-864-11 METAL CHIP  
1-216-073-00 METAL CHIP  
10K  
10K  
47  
0
10K  
5%  
5%  
5%  
5%  
5%  
1/16W  
1/16W  
1/10W  
1/16W  
1/10W  
Q301  
Q302  
Q401  
Q402  
Q403  
8-729-230-49 TRANSISTOR 2SC2712Y-TE85L  
8-729-026-49 TRANSISTOR 2SA1037AK-T146-QR  
8-729-920-85 TRANSISTOR 2SD1664-T101-QR  
8-729-106-60 TRANSISTOR 2SB1132-T101-QR  
8-729-421-22 TRANSISTOR UN2211-TX  
R402  
R403  
R404  
R405  
R406  
1-216-065-00 RES, CHIP  
1-216-065-00 RES, CHIP  
1-216-809-11 METAL CHIP  
1-218-847-11 RES, CHIP  
1-218-869-11 RES, CHIP  
4.7K  
4.7K  
100  
1K  
5%  
5%  
5%  
1/10W  
1/10W  
1/16W  
< RESISTOR >  
R101  
R102  
R104  
R201  
R202  
1-216-073-00 METAL CHIP  
1-216-833-11 RES, CHIP  
1-216-049-11 RES, CHIP  
1-216-073-00 METAL CHIP  
1-216-049-11 RES, CHIP  
10K  
10K  
1K  
10K  
1K  
5%  
5%  
5%  
5%  
5%  
1/10W  
1/16W  
1/10W  
1/10W  
1/10W  
0.5% 1/16W  
0.5% 1/16W  
8.2K  
R501  
R502  
R503  
R504  
R505  
1-216-821-11 METAL CHIP  
1-216-821-11 METAL CHIP  
1-216-821-11 METAL CHIP  
1-216-821-11 METAL CHIP  
1-216-821-11 METAL CHIP  
1K  
1K  
1K  
1K  
1K  
5%  
5%  
5%  
5%  
5%  
1/16W  
1/16W  
1/16W  
1/16W  
1/16W  
R301  
R302  
R303  
R304  
R305  
1-216-809-11 METAL CHIP  
1-216-809-11 METAL CHIP  
1-216-809-11 METAL CHIP  
1-216-809-11 METAL CHIP  
1-216-809-11 METAL CHIP  
100  
100  
100  
100  
100  
5%  
5%  
5%  
5%  
5%  
1/16W  
1/16W  
1/16W  
1/16W  
1/16W  
R506  
R507  
R510  
R511  
R512  
1-216-845-11 METAL CHIP  
1-218-863-11 RES, CHIP  
1-216-845-11 METAL CHIP  
1-216-847-11 METAL CHIP  
1-216-845-11 METAL CHIP  
100K  
4.7K  
100K  
150K  
100K  
5%  
1/16W  
0.5% 1/16W  
5%  
5%  
5%  
1/16W  
1/16W  
1/16W  
R306  
R307  
R308  
R311  
R312  
1-216-809-11 METAL CHIP  
1-216-809-11 METAL CHIP  
1-216-809-11 METAL CHIP  
1-216-821-11 METAL CHIP  
1-216-825-11 METAL CHIP  
100  
100  
100  
1K  
5%  
5%  
5%  
5%  
5%  
1/16W  
1/16W  
1/16W  
1/16W  
1/16W  
R516  
R517  
R518  
R519  
R520  
1-216-809-11 METAL CHIP  
1-216-809-11 METAL CHIP  
1-216-809-11 METAL CHIP  
1-216-809-11 METAL CHIP  
1-216-809-11 METAL CHIP  
100  
100  
100  
100  
100  
5%  
5%  
5%  
5%  
5%  
1/16W  
1/16W  
1/16W  
1/16W  
1/16W  
2.2K  
R316  
R317  
R318  
R319  
R320  
1-216-821-11 METAL CHIP  
1-216-809-11 METAL CHIP  
1-216-833-11 RES, CHIP  
1-216-845-11 METAL CHIP  
1-216-855-11 METAL CHIP  
1K  
5%  
5%  
5%  
5%  
5%  
1/16W  
1/16W  
1/16W  
1/16W  
1/16W  
100  
10K  
100K  
680K  
R521  
R522  
R523  
1-216-809-11 METAL CHIP  
1-216-821-11 METAL CHIP  
1-216-821-11 METAL CHIP  
100  
1K  
1K  
5%  
5%  
5%  
1/16W  
1/16W  
1/16W  
61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVO SUB  
Ref. No.  
Part No.  
Description  
Remark  
Ref. No.  
Part No.  
Description  
Remark  
R524  
R525  
1-216-821-11 METAL CHIP  
1-216-845-11 METAL CHIP  
1K  
100K  
5%  
5%  
1/16W  
1/16W  
MISCELLANEOUS  
**************  
R526  
R527  
R528  
R529  
R530  
1-216-825-11 METAL CHIP  
1-216-825-11 METAL CHIP  
1-216-825-11 METAL CHIP  
1-216-825-11 METAL CHIP  
1-216-825-11 METAL CHIP  
2.2K  
2.2K  
2.2K  
2.2K  
2.2K  
5%  
5%  
5%  
5%  
5%  
1/16W  
1/16W  
1/16W  
1/16W  
1/16W  
17  
17  
1-776-527-51 CORD (WITH CONNECTOR) (ISO) (POWER)  
(C6400R)  
1-776-527-61 CORD (WITH CONNECTOR) (ISO) (POWER)  
(C6500R/C6500RX)  
1-694-660-11 CONDUCTIVE BOARD, CONNECTION  
1-654-693-11 SENSOR FLEXIBLE BOARD  
8-583-065-03 OPTICAL PICK-UP KMS-241C/J1RP  
60  
153  
0165  
R531  
R532  
R533  
R534  
R535  
1-216-845-11 METAL CHIP  
1-216-864-11 METAL CHIP  
1-216-845-11 METAL CHIP  
1-216-845-11 METAL CHIP  
1-216-845-11 METAL CHIP  
100K  
0
100K  
100K  
100K  
5%  
5%  
5%  
5%  
5%  
1/16W  
1/16W  
1/16W  
1/16W  
1/16W  
CNP811 1-792-195-11 CABLE, FLEXIBLE, FLAT  
M901  
M902  
M903  
A-3301-407-A MOTOR ASSY, SP (SPINDLE)  
A-3291-190-A MOTOR ASSY, SL (SLED)  
A-3291-191-A MOTOR ASSY, LO (LOADING)  
R536  
R537  
R538  
R539  
R540  
1-216-864-11 METAL CHIP  
1-216-809-11 METAL CHIP  
1-216-845-11 METAL CHIP  
1-216-845-11 METAL CHIP  
1-216-845-11 METAL CHIP  
0
5%  
5%  
5%  
5%  
5%  
1/16W  
1/16W  
1/16W  
1/16W  
1/16W  
LCD901 1-803-906-11 DISPLAY PANEL, LIQUID CRYSTAL  
100  
100K  
100K  
100K  
(C6400R/C6500R)  
LCD901 1-803-906-31 DISPLAY PANEL, LIQUID CRYSTAL (C6500RX)  
************************************************************  
R542  
1-216-845-11 METAL CHIP  
100K  
5%  
1/16W  
**************  
HARDWARE LIST  
**************  
< COMPOSITION CIRCUIT BLOCK >  
RB301 1-233-576-11 RES, CHIP NETWORK 100  
RB302 1-233-576-11 RES, CHIP NETWORK 100  
RB503 1-233-412-11 RES, CHIP NETWORK 1K (3216)  
#1  
#2  
#3  
#4  
#5  
7-621-772-20 SCREW +B 2X5  
7-685-795-09 SCREW +PTT 2.6X12 (S)  
7-685-793-09 SCREW +PTT 2.6X8 (S)  
7-685-647-79 SCREW +BVTP 3X10 TYPE2 IT-3  
7-685-851-04 SCREW +BVTT 2X4 (S)  
< THERMISTOR >  
TH501 1-810-421-11 THERMISTOR NTH5G36B103K01TE  
< VIBRATOR >  
#6  
#7  
#8  
7-624-102-04 STOP RING 1.5, TYPE-E  
7-627-852-37 PRECISION SCREW +P 1.7X1.8 TYPE 3  
7-621-772-08 SCREW +B 2X3  
#9  
7-621-555-10 SCREW +K 2X3  
X301  
X501  
1-767-429-21 VIBRATOR, CRYSTAL (22.5792MHz)  
1-760-365-11 VIBRATOR, CERAMIC (10MHz)  
#10  
7-685-793-09 SCREW +PTT 2.6X8 (S)  
**************************************************************  
#11  
#12  
#13  
7-685-791-09 SCREW +PTT 2.6X5 (S)  
7-627-553-28 SCREW, PRECISION +P 2X2.5  
7-685-106-19 SCREW +P 2X10 TYPE2 NON-SLIT  
*
1-677-057-11 SUB BOARD  
**********  
************************************************************  
< CONNECTOR >  
ACCESSORIESE & PACKING MATERIALS  
*********************************  
CNP810 1-794-064-11 SOCKET, CONNECTOR 14P  
CNP811 1-792-195-11 CABLE, FLEXIBLE FLAT  
3-044-659-11 MANUAL, INSTRUCTION (ENGLISH, SPANISH,  
SWEDISH, PORTUGUESE, RUSSIAN)  
< DIODE >  
(C6500R/C6500RX: AEP, UK)  
3-044-659-21 MANUAL, INSTRUCTION (FRENCH, GERMAN,  
D806  
D810  
D811  
D812  
D813  
D814  
8-719-109-97 DIODE RD6.8ESB2  
DUTCH, ITALIAN, GREEK)  
(C6400R/C6500R/C6500RX: AEP)  
3-044-659-31 MANUAL, INSTRUCTION (GERMAN)  
8-719-056-82 DIODE UDZ-TE-17-6.2B  
8-719-056-82 DIODE UDZ-TE-17-6.2B  
8-719-056-82 DIODE UDZ-TE-17-6.2B  
8-719-056-82 DIODE UDZ-TE-17-6.2B  
8-719-056-82 DIODE UDZ-TE-17-6.2B  
(C6400R/C6500R/C6500RX: German)  
3-044-660-11 MANUAL, INSTRUCTION, INSTALL (ENGLISH,  
SPANISH, SWEDISH, PORTUGUESE, RUSSIAN)  
(C6500R/C6500RX: AEP, UK)  
< LED >  
3-044-660-21 MANUAL, INSTRUCTION, INSTALL (FRENCH,  
GERMAN, DUTCH, ITALIAN, GREEK)  
LED810 8-719-077-75 LED BR1101F-TR (MD DISC SLOT) (C6500RX)  
LED810 8-719-077-78 LED BG1101F-TR (MD DISC SLOT)  
(C6400R, C6500R)  
(C6400R/C6500R/C6500RX: AEP)  
X-3378-490-1 CASE (PANEL) ASSY  
************************************************************  
< SWITCH >  
LSW810 1-771-609-11 SWITCH, TACTILE (WITH LED) (Z)  
(C6400R, C6500R)  
LSW810 1-771-883-21 SWITCH, TACTILE (WITH LED) (Z) (C6500RX)  
**************************************************************  
The components identified by mark 0 or dotted  
line with mark 0 are critical for safety.  
Replace only with part number specified.  
62  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ver 1.1 2001.05  
Ref. No.  
Part No.  
Description  
Remark  
PARTS FOR INSTALLATION AND CONNECTION  
*************************************  
501  
502  
503  
504  
505  
1-465-459-21 ADAPTER, ANTENNA  
3-012-360-31 FRAME  
3-040-979-01 COLLAR  
3-233-644-01 SPRING, FITTING  
3-934-325-01 SCREW, +K (5X8) TAPPING  
506  
507  
X-3366-405-1 SCREW ASSY (EXP), FITTING  
1-776-527-51 CORD (WITH CONNECTOR) (ISO) (POWER)  
(C6400R)  
507  
1-776-527-61 CORD (WITH CONNECTOR) (ISO) (POWER)  
(C6500R/C6500RX)  
501  
502  
ADAPTER, ANTENNA  
FRAME  
× 1  
× 1  
503  
504  
COLLAR  
× 1  
SPRING, FITTING  
× 2  
506  
505  
SCREW, FITTING  
BUSHING  
× 1  
+K5 × 8  
× 2  
× 1  
507  
POWER CORD  
× 1  
63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MDX-C6400R/C6500R/C6500RX  
REVISION HISTORY  
Clicking the version allows you to jump to the revised page.  
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised  
page.  
Ver.  
1.2  
1.1  
1.0  
Date  
Description of Revision  
Change of Part No. for TU1  
2001.12  
2001.05  
2000.02  
(RPC-01002)  
Change of Part No. for SPRING, FITTING  
New  
(ECN-CSA04727)  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Sennheiser Wireless Office Headset SD Pro 1 User Manual
Sharp All in One Printer FO DC635 User Manual
Snapper Lawn Aerator 3538 User Manual
Solid State Logic Stereo Amplifier 82S6XR0A0B User Manual
Sony Clock Radio ICF C793 User Manual
Sony Ericsson Portable Multimedia Player D750 User Manual
Sony Network Card PCWA C500 User Manual
StarTechcom Universal Remote SV11151PEXT User Manual
Sterling Plumbing Indoor Furnishings 402015 User Manual
Sunbeam Kitchen Grill GR7200 User Manual