C7Z87-OCE
USER’S MANUAL
Revision 1.0a
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Preface
This manual is written for system integrators, PC technicians and
knowledgeable PC users. It provides information for the installation and use of the
C7Z87-OCE motherboard.
About This Motherboard
The
C7Z87-OCE supports a single 4th Generation Intel® Core™ i7/i5/i3
DT processor in an LGA 1150 (H3) socket. With the Intel® Z87 Express chipset built
in, the C7Z87-OCE motherboard offers substantial system performance and storage
capability for overclocking platforms in a sleek package. Please refer to our website
(http://www.supermicro.com/products/) for processor and memory support updates.
This product is intended to be installed and serviced by professional technicians.
Manual Organization
Chapter 1 describes the features, specifications and performance of the mother-
board, and provides detailed information on the Intel Z87 Express chipset.
Chapter 2 provides hardware installation instructions. Read this chapter when in-
stalling the processor, memory modules and other hardware components into the
system. If you encounter any problems, see Chapter 3, which describes trouble-
shooting procedures for video, memory and system setup stored in the CMOS.
Chapter 4 includes an introduction to the BIOS, and provides detailed information
on running the CMOS Setup utility.
Appendix A provides BIOS Error Beep Codes.
Appendix B lists software program installation instructions.
Appendix C contains UEFI BIOS Recovery instructions.
Appendix D contains an introduction and instructions regarding the Dual Boot Block
feature of this motherboard.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
Conventions Used in the Manual:
Special attention should be given to the following symbols for proper installation and
to prevent damage done to the components or injury to yourself:
Warning: Critical information to prevent damage to the components or injury to your-
self.
Important: Important information given to ensure proper system installa-
tion or to relay safety precautions.
Note: Additional Information given to differentiate various models or pro-
vides information for correct system setup.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Contacting Supermicro
Contacting Supermicro
Headquarters
Address:
Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
+1 (408) 503-8000
+1 (408) 503-8008
Tel:
Fax:
Email:
[email protected] (General Information)
www.supermicro.com
Web Site:
Europe
Address:
Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
+31 (0) 73-6400390
Tel:
Fax:
Email:
+31 (0) 73-6416525
[email protected] (General Information)
[email protected] (Customer Support)
Asia-Pacific
Address:
Super Micro Computer, Inc.
3F, No. 150, Jian 1st Rd.
Zhonghe Dist., New Taipei City 23511
Taiwan (R.O.C)
Tel:
+886-(2) 8226-3990
Fax:
+886-(2) 8226-3992
Web Site:
www.supermicro.com.tw
Technical Support:
Email:
Tel:
+886-(2)-8226-3990
v
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
Table of Contents
Preface
Chapter 1 Introduction
1-1
1-2
1-3
1-4
1-5
1-6
1-7
Overview ......................................................................................................... 1-1
Chipset Overview ........................................................................................... 1-9
Special Features ........................................................................................... 1-10
PC Health Monitoring.................................................................................... 1-10
ACPI Features................................................................................................1-11
Power Supply.................................................................................................1-11
Super I/O....................................................................................................... 1-12
Chapter 2 Installation
2-1
2-2
2-3
Standardized Warning Statements ................................................................. 2-1
Battery Handling.............................................................................................. 2-1
Product Disposal............................................................................................. 2-3
Static-Sensitive Devices.................................................................................. 2-4
Precautions ..................................................................................................... 2-4
Unpacking ....................................................................................................... 2-4
Processor and Heatsink Installation................................................................ 2-5
Installing the LGA1150 Processor ................................................................. 2-5
Installing an Active CPU Heatsink with Fan ................................................... 2-8
Removing the Heatsink................................................................................. 2-10
Installing DDR3 Memory................................................................................2-11
DIMM Installation ...........................................................................................2-11
Removing Memory Modules ..........................................................................2-11
Memory Support............................................................................................ 2-12
Memory Population Guidelines..................................................................... 2-12
Memory Population Guidelines..................................................................... 2-13
Motherboard Installation................................................................................ 2-14
Tools Needed ................................................................................................ 2-14
Location of Mounting Holes .......................................................................... 2-14
Installing the Motherboard ............................................................................ 2-15
Connectors/IO Ports...................................................................................... 2-16
Backplane I/O Panel ..................................................................................... 2-16
Universal Serial Bus (USB)...................................................................... 2-17
Ethernet Ports .......................................................................................... 2-18
Back Panel High Definition Audio (HD Audio) ........................................ 2-18
HDMI Port................................................................................................. 2-19
2-4
2-5
2-6
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
VGA Port .................................................................................................. 2-19
DVI Port.................................................................................................... 2-19
Thunderbolt Interface ............................................................................... 2-20
CMOS Reset/Clear................................................................................... 2-20
Front Control Panel....................................................................................... 2-21
Front Control Panel Pin Definitions............................................................... 2-22
Power LED .............................................................................................. 2-22
HDD LED.................................................................................................. 2-22
NIC1/NIC2 (LAN1/LAN2).......................................................................... 2-22
Overheat (OH)/Fan Fail............................................................................ 2-22
Reset Button ........................................................................................... 2-23
Power Button ........................................................................................... 2-23
Connecting Cables........................................................................................ 2-24
ATX Main PWR & CPU PWR Connectors (JPW1 & JPW2) ................... 2-24
Fan Headers (Fan 1 ~ Fan 5).................................................................. 2-25
Chassis Intrusion (JL1) ........................................................................... 2-25
Internal Buzzer (SP1)............................................................................... 2-26
Speaker (JD1) .......................................................................................... 2-26
Onboard Power LED (JLED1).................................................................. 2-27
Serial Port (COM1)................................................................................... 2-27
DOM PWR Connector (JSD1).................................................................. 2-28
SPDIF OUT (JSPDIF_OUT)..................................................................... 2-28
Standby Power Header............................................................................ 2-29
Chassis LED............................................................................................. 2-29
TPM Header/Port 80 Header ................................................................... 2-30
Front Panel Audio Header (AUDIO FP)................................................... 2-31
Jumper Settings ............................................................................................ 2-32
Explanation of Jumpers ................................................................................ 2-32
LAN1/LAN2 Enable/Disable ..................................................................... 2-32
CMOS Clear (JBT1)................................................................................. 2-33
2-7
2-8
PCI Slot SMB Enable (I2C1/I2C2)............................................................. 2-33
Audio Enable (JPAC1).............................................................................. 2-34
Watch Dog Enable/Disable ...................................................................... 2-34
USB Wake-Up (JPUSB 1/2)..................................................................... 2-35
Over-Clocking Buttons (OC1,OC2, OC3)................................................. 2-35
Management Engine (ME) Recovery (JPME1)........................................ 2-36
Manufacture Mode (JPME2) .................................................................... 2-36
BIOS Recovery (JBR1) ............................................................................ 2-37
Power Button............................................................................................ 2-37
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
2-9
Onboard Indicators........................................................................................ 2-38
LAN 1/LAN 2 LEDs .................................................................................. 2-38
Onboard Power LED (LED1) .................................................................. 2-38
Status Display (LED3,LED2) ................................................................... 2-39
2-10 SATA Connections......................................................................................... 2-40
SATA Connections (I-SATA0~I-SATA5).................................................... 2-40
Chapter 3 Troubleshooting
3-1
3-2
3-3
3-4
3-5
Troubleshooting Procedures ........................................................................... 3-1
Technical Support Procedures........................................................................ 3-3
Frequently Asked Questions........................................................................... 3-4
Battery Removal and Installation.................................................................... 3-5
Returning Merchandise for Service................................................................. 3-6
Chapter 4 BIOS
4-1
4-2
4-3
4-4
4-5
Introduction...................................................................................................... 4-1
Main Setup...................................................................................................... 4-2
Advanced Setup Configurations...................................................................... 4-4
Boot Settings................................................................................................. 4-38
Security Settings ........................................................................................... 4-40
4-6
Save & Exit ................................................................................................... 4-41
Appendix A BIOS Error Beep Codes
A-1
BIOS Error Beep Codes .................................................................................A-1
Appendix B Software Installation Instructions
B-1
Installing Drivers..............................................................................................B-1
®
B-2
Configuring SuperDoctor III..........................................................................B-2
Appendix C UEFI BIOS Recovery Instructions
C-1
C-2
C-3
An Overview to the UEFI BIOS ......................................................................C-1
How to Recover the UEFI BIOS Image (-the Main BIOS Block)....................C-1
To Recover the Main BIOS Block Using a USB-Attached Device..................C-1
Appendix D Dual Boot Block
D-1
Introduction......................................................................................................D-1
BIOS Boot Block .............................................................................................D-1
BIOS Boot Block Corruption Occurrence ......................................................D-1
Steps to Reboot the System by Using Jumper JBR1 ....................................D-2
D-2
viii
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
Chapter 1
Introduction
1-1 Overview
Checklist
Congratulations on purchasing your computer motherboard from an acknowledged
leader in the industry. Supermicro boards are designed with the utmost attention to
detail to provide you with the highest standards in quality and performance.
Please check that the following items have all been included with your motherboard.
If anything listed here is damaged or missing, contact your retailer.
The following items are included in the retail box.
•
•
•
•
One (1) Supermicro Motherboard
Two (2) SATA cables
One (1) I/O shield
One (1) Quick Reference Guide
Note: For your system to work properly, please follow the links below to
download all necessary drivers/utilities and the user's manual for your
motherboard.
SMCI product manuals: http://www.supermicro.com/support/manuals/
Product Drivers and utilities: ftp://ftp.supermicro.com/
If you have any questions, please contact our support team at support@supermicro.
com.
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
C7Z87-OCE Motherboard Image
Note: All graphics shown in this manual were based upon the latest PCB Revision
available at the time of publishing of the manual. The motherboard you've received
may or may not look exactly the same as the graphics shown in this manual.
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
C7Z87-OCE Motherboard Layout
CLEAR CMOS SWITCH
THUNDERBOLT
HDMI
VGA/DVI
JPAC1
USB 0/1
HD AUDIO
1
1
1
JSPDIF_OUT
FAN5
JPAC1:AUDIO
1-2:ENABLE
2-3:DISABLE
USB 16/17
USB 6/7(3.0)
LAN1
USB 14/15
USB 4/5(3.0)
LAN2
JPL2
1-2
LAN2
PCIE1
JPCIE2
PCIE3
JPCIE4
PCIE5 JPCIE6
ENABLE
DISABLE
2-3
1
JPL2
JI2C1/JI2C2
ON:ENABLE
OFF:DISABLE
JI2C2
1
1
1
JI2C1
JVR1
3
4
1
J
P
L
1
L
A
N
1
1-2
2-3
ENABLE
DISABLE
A
CPU
C
1
BIOS LICENSE
5
2
1
1
4
LED3 LED2
2
JTPM1
JPME1:
1-2:NORMAL
2-3:ME RECOVERY
Tested to Comply
JWD1: WATCH DOG
1-2:RST
2-3:NMI
With FCC Standards
FOR HOME OR OFFICE USE
JWOR1:
WAKE ON RING
19
ALWAYS POPULATE BLUE SOCKET FIRST
UNB NON-ECC DDR3 DIMM REQUIRED
20
JWD1
3
3
P1-DIMMA1
P1-DIMMA2
1
JPME1
1
JSTBY1
3
JBT1
R298
1
BATTERY
USB4/5
USB6/7
7
P1-DIMMB1
P1-DIMMB2
10
2
1
1
1
JPME2
USB 2/3
7
JBR1
USB 2/3(3.0)
JBR1:
1-2:NORMAL
USB12/13
10
10
2-3:BIOS RECOVERY
1
1
OC3
19
11
OC2
OC1
SP1
JLED1
USB 0/1(3.0)
JD1
3
JLED1:
3
PIN POWER LED
JSD1
CLEAR
CMOS
JPW1
1
1
4
I-SATA2
I-SATA3
JOCE
I-SATA0
I-SATA1
I-SATA4 A-SATA0
I-SATA5
1
4
4
1
JF1
1
JD1:
SPEAKER:1-4
BUZZER:3-4
1
6
A-SATA1
PWR
ON
OH/FF
LED
HDD PWR
LED LED
RST
N
I
C
2
N
I
C
1
X
FAN3
JF1
LED1
Important Notes to the User
•
See Chapter 2 for detailed information on jumpers, I/O ports and JF1 front
panel connections.
•
•
•
" " indicates the location of "Pin 1".
Jumpers not indicated are for testing only.
When LED1 (Onboard Power LED Indicator) is on, system power is on. Un-
plug the power cable before installing or removing any components.
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
C7Z87-OCE Quick Reference
CLEAR CMOS SWITCH
THUNDERBOLT
HDMI
VGA/DVI
JPAC1
USB 0/1
HD AUDIO
1
1
1
JSPDIF_OUT
FAN5
JPAC1:AUDIO
1-2:ENABLE
2-3:DISABLE
USB 16/17
USB 6/7(3.0)
LAN1
USB 14/15
USB 4/5(3.0)
LAN2
JPL2
1-2
LAN2
PCIE1
JPCIE2
PCIE3
JPCIE4
PCIE5 JPCIE6
ENABLE
DISABLE
2-3
1
JPL2
JI2C1/JI2C2
ON:ENABLE
OFF:DISABLE
JI2C2
1
1
1
JI2C1
JVR1
3
4
1
J
P
L
1
L
A
N
1
1-2
2-3
ENABLE
DISABLE
A
CPU
C
1
BIOS LICENSE
5
2
1
1
4
LED3 LED2
2
JTPM1
JPME1:
1-2:NORMAL
2-3:ME RECOVERY
Tested to Comply
JWD1: WATCH DOG
1-2:RST
2-3:NMI
With FCC Standards
FOR HOME OR OFFICE USE
JWOR1:
WAKE ON RING
19
ALWAYS POPULATE BLUE SOCKET FIRST
UNB NON-ECC DDR3 DIMM REQUIRED
20
JWD1
3
3
P1-DIMMA1
P1-DIMMA2
1
JPME1
1
JSTBY1
3
JBT1
R298
1
BATTERY
USB4/5
USB6/7
7
P1-DIMMB1
P1-DIMMB2
10
2
1
1
1
JPME2
USB 2/3
7
JBR1
USB 2/3(3.0)
JBR1:
1-2:NORMAL
USB12/13
10
10
2-3:BIOS RECOVERY
1
1
OC3
19
11
OC2
OC1
SP1
JLED1
USB 0/1(3.0)
JD1
3
JLED1:
3
PIN POWER LED
JSD1
CLEAR
CMOS
JPW1
1
1
4
I-SATA2
I-SATA3
JOCE
I-SATA0
I-SATA1
I-SATA4 A-SATA0
I-SATA5
1
4
4
1
JF1
1
JD1:
SPEAKER:1-4
BUZZER:3-4
1
6
A-SATA1
PWR
ON
OH/FF
LED
HDD PWR
LED LED
24
RST
N
I
C
2
N
I
C
1
X
FAN3
JF1
LED1
Jumpers
Jumper
Description
Default
JBT1
Clear CMOS
(See Chpt. 2)
Off (Disabled)
JI2C1/JI2C2
SMB to PCI Slots
JPAC1
Audio Enable
Pins 1-2 (Enabled)
Pins 1-2 (Enabled)
Pins 2-3 (Disabled)
Pins 2-3 (Disabled)
Pins 2-3 (NMI)
JPL1/JPL2
JPME1
JPME2
JWD1
LAN1/LAN2 Enable
Intel Manufacturing Mode
Intel Recovery Mode
Watch Dog Enable
BIOS Recovery Mode
JBR1
Pins 2-3 (Disabled)
Pins 1-2 (Enabled)
Pins 1-2 (Enabled)
JPUSB1
JPUSB2
USB Wake Up Enable (Back Panel)
USB Wake Up Enable (USB Headers)
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
Connectors and Switches
Connector
I/O Back Panel
Audio FP
Battery
Description
See page 2-16 for details
Front Panel Audio Header
Onboard Battery
COM1
COM1 Port Header
Fan 1,2,3,4,5
JD1
System/CPU Fan Headers (Fan1: CPU Fan)
Speaker/buzzer (Pins 1-2: Buzzer, Pins 1~4: External Speaker)
Front Panel Control Header
JF1
JL1
Chassis Intrusion Header
JL2
Reserved
JLED1
Power LED Indicator Header
JPW1
24-pin ATX Main Power Connector (Required)
+12V 4-pin CPU power Connector (Required)
SATA DOM (Disk On Module) Power Connector
Sony/Philips Digital Interface (S/PDIF) Out Header
Standby Power Header
JPW2
JSD1
JSPDIF_OUT
JSTBY1
JTPM1
Trusted Platform Module/Port 80 Connector
Internal Speaker/Buzzer
SP1
A-SATA0/1
I-SATA0~5
USB 0/1
USB 2/3
USB 4/5, 6/7
JCHLED1
ASMedia) Serial ATA (SATA 3.0) Port 0 / Port 1(6Gb/sec)
(Intel Z87) Serial ATA (SATA 3.0) Ports 0~5 (6Gb/sec)
Front Panel Accessible USB 3.0 Ports 0/1 (USB 2.0 12/13)
Front Panel Accessible USB 3.0 Ports 2/3 (USB 2.0 2/3)
Front Panel Accessible USB 2.0 Headers 4/5,6/7,8/9,10/11
Chassis LED Control (Supermicro Chassis only)
POWERBUTTON Internal Power Button
OC1, OC2, OC3
CLEAR CMOS
Over-Clocking Buttons OC1(15%), OC2(20-25%), OC3 (User-Defined in BIOS)
Resets the contents of the CMOS to default values
LED Indicators
LED
Description
Color/State
Status
LED1
Onboard Standby PWR LED
Status Display
Green: Solid on
Digital Readout
Power On
LED2/LED3
See Table xx
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
Motherboard Features
CPU
Single 4th Generation Intel® Core™ i7/i5/i3 DT processor
in an LGA1150 socket.
Memory
Four (4) SDRAM slots support up to 32 GB of DDR3 Unbuf-
fered, Non-ECC 1600/1333/1066 MHz memory
Single-channel memory
DIMM sizes
UDIMM
1 GB, 2 GB, 4GB, and 8GB
Chipset
Intel® Z87 Express
Expansion Slots
Three (3) PCI Express 2.0 x1 (in x4) slots
One (1) PCI Express 3.0 x16/x8/x4 (in x16) slot*
One (1) PCI Express 3.0 x8/x4 (in x16) slot*
One (1) PCI Express 3.0 x4 (in x16) slot*
Network Connections Two (2) Gigabit Ethernet Controllers:
LAN1: Intel i217 gigabit LAN controller
LAN2: Intel i210 gigabit LAN controller
Two (2) RJ-45 rear I/O panel connectors with Link and
Activity LEDs
I/O Devices
SATA Connections
SATA 3.0 (6Gb/s)
SATA 3.0 (6Gb/s)
Two (2) A-SATA 0~1, via ASM1061
Six (6) I-SATA 0~5, via Intel Z87
RAID 0, 1, 5, 10
USB Devices
Four (4) USB 2.0 ports and Four (4) USB 3.0 ports on the
rear I/O panel
Four (2) Front-Accessible USB 2.0 ports on Two head-
ers and Four (4) Front Accessible USB 3.0 ports on two
headers
Keyboard/Mouse
One shared PS/2 Keyboard/Mouse port on the I/O
backpanel
Other I/O Ports
One (1) Thunderbolt Port (DP 1.1 from PCH, PCI-E x4)
One (1) DV-I Port
One (1) HDMI Port
One (1) Serial Port header (COM1)
*Note for VGA Cards: For a single VGA card, install the VGA card into the JPCIE6 (x16) slot. For SLI™ or
CrossFireX™ mode (two VGA cards linked), install one card each into JPCIE6 (x16) and JPCIE4 (x8) slots.
1-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
Audio
One (1) High Definition Audio 7.1 channel connector sup-
ported by Realtek ALC1150 on the back panel
One (1) Front Panel Audio Header
One (1) SPDIF In/Out on the rear side of the chassis
Super I/O
Nuvoton NCT6776D
BIOS
128 Mb AMI BIOS® SPI Flash BIOS
Play and Plug (PnP0, DMI 2.3, PCI 2.3, ACPI 1.0/2.0/3.0,
USB Keyboard and SMBIOS 2.5
Power Configuration
ACPI/ACPM Power Management
Main Switch Override Mechanism
Keyboard Wake-up from Soft-Off
Internal/External Modem Ring-On
Power-on mode for AC power recovery
PC Health Monitoring CPU Monitoring
Onboard voltage monitors for CPU core, +3.3V, +5V,-12V,
+12V, +3.3V Stdby, +5V Stdby, VBAT, Memory, VCORE
for CPU
CPU 4-phase switching voltage regulator
CPU/System overheat LED and control
CPU Thermal Trip support
Thermal Monitor 2 (TM2) support
Fan Control
Fan status monitoring with firmware 4-pin fan speed con-
trol via IPMI interface
Low noise fan speed control
System Management
PECI (Platform Environment Configuration Interface) 2.0
support
System resource alert via SuperDoctor® III
SuperDoctor III, Watch Dog, NMI
One (1) CMOS Reset Button on the rear panel
Chassis Intrusion header and detection
BIOS flash upgrade utility
CD Utilities
Drivers and software for Intel® Z87 Express chipset utili-
ties
Other
ROHS 6/6 (Full Compliance, Lead Free)
Dimensions
ATX form factor (12.0" x 9.6") (304.8 mm x 243.84 mm)
1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
C7Z87-OCE Block Diagram
RoHS 6/6
P19
PCIe x16 SLOT #6
PCIe3.0_x8
8.0GT/s
SVID
or
P20
VRM 12.5
PCIe x8(in x16) SLOT #4
PCIe x8(in x16) SLOT #6
PCIe3.0_x4
8.0GT/s
or
PCIe x4(in x16) SLOT #4
PCIe3.0_x8
8.0GT/s
INTEL LGA1150
PCIe3.0_x4
8.0GT/s
Haswell - DT
DDR3 (CHA)
DIMM1A (Blue)
DIMM1B(Black)
P19
1
2
P20
1
3
(Socket-H3)
2
4
1600/1333/1066MHz
PCIe3.0_x4
8.0GT/s
PCIe3.0_x8
8.0GT/s
TI Switch
HD3SS3415
TI Switch
HD3SS3415
DDR3 (CHB)
VRD12.5
DIMM2A (Blue)
DIMM2B(Black)
1600/1333/1066MHz
PCIe3.0_x4
8.0GT/s
P20
x4 DMI
5GT/s
x2 FDI
2.7 Gbps
PCIe x4(in x16) SLOT #2
HDMI
DP
DVI
THUNDERBOLT
PCIe2.0_x1
2.5GT/s
PCIe x1 SLOT #1
PCIe x1 SLOT #3
PCIe x1 SLOT #5
Redwood Ridge
PCIe2.0_x1
2.5GT/s
PCIe2.0_x4
2.5GT/s
CBTL05023BS
Mini-DP
Intel
PCIe2.0_x1
2.5GT/s
PLX8606
PCIe2.0_x1
2.5GT/s
Lynx Point
Z87/C226
uPD720201
USB3.0 X4
PCIe2.0_x1
2.5GT/s
PCIe2.0_x1
2.5GT/s
GLAN1
i217V
RJ45
RJ45
PCH
PCIe2.0_x1
2.5GT/s
GLAN2
i210IT
SATA-III
6SATA-III PORTS
10 USB 2.0 PORTS
4 USB 3.0 PORTS
600MB/s
USB2.0
480Mbps
PCIe2.0_x1
2.5GT/s
ASM1061
SATA6G X2
USB3.0
5Gbps
Analogl port
A
VGA
FLASH
SPI 128Mb
SPI
AZALIA
LPC
RealTek ALC1150
LPC
TPM1.2(Header)
COM1
NCT6776D
HEALTH
INFO
LPC I/O
System Block Diagram
Note: This is a general block diagram and may not exactly represent
the features on your motherboard. See the Motherboard Features
pages for the actual specifications of each motherboard.
1-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
1-2 Chipset Overview
The C7Z87-OCE motherboard supports a single 4th Generation Intel® Core i7/i5/i3
DT processor in the LGA 1150 Socket. Built upon the functionality and the capability
of the Z87 Express chipset, the motherboard provides substantial enhancement to
system performance, including overclocking capability.
The high-speed Direct Media Interface (DMI) featured in the Intel Z87 Express
chipset supports high-speed Direct Media Interface (DMI) for chip-to-chip true iso-
chronous communication, providing up to 10 Gb/s of software-transparent data
transfer rate on each read/write direction. In addition, the C7Z87 also features a
TCO timer which allows the system to recover from a software/hardware lock and
perform tasks, including Function Disable and Intruder Detect.
Intel Z87 Express Chipset Features
•
•
•
•
•
•
•
•
Direct Media Interface (up 10 Gb/s transfer, Full Duplex)
Intel® Matrix Storage Technology and Intel Rapid Storage Technology
Dual NAND Interface
Intel I/O Virtualization (VT-d) Support
Intel Trusted Execution Technology Support
PCI Express 2.0 Interface (up to 5.0 GT/s)
SATA Controller (up to 6Gb/sec)
Advanced Host Controller Interface (AHCI)
1-9
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
1-3 Special Features
Recovery from AC Power Loss
Basic I/O System (BIOS) provides a setting for you to determine how the system will
respond when AC power is lost and then restored to the system. You can choose
for the system to remain powered off, (in which case you must press the power
switch to turn it back on), or for it to automatically return to a power-on state. See
the Advanced BIOS Setup section to change this setting. The default setting is
Last State.
1-4 PC Health Monitoring
This section describes the PC health monitoring features of the board. All have an
onboard System Hardware Monitoring chip that supports PC health monitoring. An
onboard voltage monitor will scan these onboard voltages continuously: CPU Vcore,
12V, -12V, 5V, 5VSB, 3.3V, 3.3VSB, and Battery voltages. Once a voltage becomes
unstable, a warning is given, or an error message is sent to the screen. The user
can adjust the voltage thresholds to define the sensitivity of the voltage monitor.
Fan Status Monitor with Firmware Control
PC health monitoring in the BIOS can check the RPM status of the cooling fans.
The onboard CPU and chassis fans are controlled by Thermal Management via
IPMI Firmware.
Environmental Temperature Control
The thermal control sensor monitors the CPU temperature in real time and will turn
on the thermal control fan whenever the CPU temperature exceeds a user-defined
threshold. The overheat circuitry runs independently from the CPU. Once the ther-
mal sensor detects that the CPU temperature is too high, it will automatically turn
on the thermal fans to prevent the CPU from overheating. The onboard chassis
thermal circuitry can monitor the overall system temperature and alert the user when
the chassis temperature is too high.
Note: To avoid possible system overheating, please be sure to provide
adequate airflow to your system.
System Resource Alert
This feature is available when the system is used with SuperDoctor III in the
Windows OS environment or used with SuperDoctor II in Linux. SuperDoctor
1-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
is used to notify the user of certain system events. For example, you can also
configure SuperDoctor to provide you with warnings when the system temperature,
CPU temperatures, voltages and fan speeds go beyond predefined thresholds.
1-5 ACPI Features
ACPI stands for Advanced Configuration and Power Interface. The ACPI specifica-
tion defines a flexible and abstract hardware interface that provides a standard
way to integrate power management features throughout a PC system, including
its hardware, operating system and application software. This enables the system
to automatically turn on and off peripherals such as CD-ROMs, network cards, hard
disk drives and printers.
In addition to enabling operating system-directed power management, ACPI also
provides a generic system event mechanism for Plug and Play, and an operating
system-independent interface for configuration control. ACPI leverages the Plug and
Play BIOS data structures, while providing a processor architecture-independent
implementation that is compatible with Windows 7, Windows 8, and Windows 2008
Operating Systems.
Slow Blinking LED for Suspend-State Indicator
When the CPU goes into a suspend state, the chassis power LED will start to blink
to indicate that the CPU is in suspend mode. When the user presses any key, the
CPU will "wake up", and the LED will automatically stop blinking and remain on.
1-6 Power Supply
As with all computer products, a stable power source is necessary for proper and
reliable operation. It is even more important for processors that have high CPU
clock rates.
This motherboard accommodates 24-pin ATX power supplies. Although most
power supplies generally meet the specifications required by the CPU, some are
inadequate. In addition, the 12V 8-pin power connector located at JPW2 is also
required to ensure adequate power supply to the system. Also your power supply
must supply 1.5A for the Ethernet ports.
Warning! To prevent damage to the power supply or motherboard, please use a
power supply that contains a 24-pin and a 8-pin power connectors. Be sure to con-
nect these connectors to the 24-pin (JPW1) and the 8-pin (JPW2) power connectors
on the motherboard.
It is strongly recommended that you use a high quality power supply that meets ATX
power supply Specification 2.02 or above. It must also be SSI compliant. (For more
1-11
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
information, please refer to the web site at http://www.ssiforum.org/). Additionally, in
areas where noisy power transmission is present, you may choose to install a line
filter to shield the computer from noise. It is recommended that you also install a
power surge protector to help avoid problems caused by power surges.
1-7 Super I/O
The Super I/O supports two high-speed, 16550 compatible serial communication
ports (UARTs). Each UART includes a 16-byte send/receive FIFO, a programmable
baud rate generator, complete modem control capability and a processor interrupt
system. Both UARTs provide legacy speed with baud rate of up to 115.2 Kbps
as well as an advanced speed with baud rates of 250 K, 500 K, or 1 Mb/s, which
support higher speed modems.
The Super I/O provides functions that comply with ACPI (Advanced Configuration
and Power Interface), which includes support of legacy and ACPI power manage-
ment through an SMI or SCI function pin. It also features auto power management
to reduce power consumption.
1-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
Chapter 2
Installation
2-1 Standardized Warning Statements
The following statements are industry-standard warnings, provided to warn the user
of situations which have the potential for bodily injury. Should you have questions or
experience difficulty, contact Supermicro's Technical Support department for assis-
tance. Only certified technicians should attempt to install or configure components.
Read this section in its entirety before installing or configuring components in the
Supermicro chassis.
Battery Handling
Warning!
There is a danger of explosion if the battery is replaced incorrectly. Replace the
battery only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's instructions
電池の取り扱い
電池交換が正しく行われなかった場合、破裂の危険性があります。交換する電池はメー
カーが推奨する型、または同
等のものを使用下さい。使用済電池は製造元の指示に従
って処分して下さい。
警告
电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更
换原有电池。请按制造商的说明处理废旧电池。
警告
電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有
電池。請按照製造商的說明指示處理廢棄舊電池。
Warnung
Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die
Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp.
Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
Attention
Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer
que par une pile de type semblable ou équivalent, recommandée par le fabricant.
Jeter les piles usagées conformément aux instructions du fabricant.
¡Advertencia!
Existe peligro de explosión si la batería se reemplaza de manera incorrecta. Re-
emplazar la batería exclusivamente con el mismo tipo o el equivalente recomen-
dado por el fabricante. Desechar las baterías gastadas según las instrucciones
del fabricante.
!
אזהרה ף להחלי יש .תקינה לא בדרך והוחלפה במידה הסוללה של פיצוץ סכנת קיימת .
מומלצת יצרן מחברת התואם בסוג הסוללה את .
היצרן הוראות לפי לבצע יש המשומשות הסוללות סילוק ل ي ل فع ة حيح ص ر ي غ قة ي طر ب ة ري بطا ال ل ا سحبذ ا ة ل ا ح في ر جا ف ن ا ن م خطر هناك ة ري بطا ال ل ا سحبذ ا ة نع المص ة م شر ال ه ب أوصث ا م م ا له عاد ي ما أو ع نى ال فس ن ب ط فق ة ع ن ا الص ة م شر ال ات م ي ل حع ل وفقا ة ل م حع س الم ات ري بطا ال ن م ص ل جخ 경고!
배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와 동일
하거나 제조사에서 권장하는 동등한 종류의 배터리로만 교체해야 합니다. 제조사
의 안내에 따라 사용된 배터리를 처리하여 주십시오.
Waarschuwing
Er is ontploffingsgevaar indien de batterij verkeerd vervangen wordt. Vervang de
batterij slechts met hetzelfde of een equivalent type die door de fabrikant aan-
bevolen wordt. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften
afgevoerd te worden.
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
Product Disposal
Warning!
Ultimate disposal of this product should be handled according to all national laws
and regulations.
製品の廃棄
この製品を廃棄処分する場合、国 の関係する全ての法律・条例に従い処理する必要
が
あります。
警告
本产品的废弃处理应根据所有国家的法律和规章进行。
警告
本產品的廢棄處理應根據所有國家的法律和規章進行。
Warnung
Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen
des Landes erfolgen.
¡Advertencia!
Al deshacerse por completo de este producto debe seguir todas las leyes y regla-
mentos nacionales.
Attention
La mise au rebut ou le recyclage de ce produit sont généralement soumis à des
lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de
l'organisme compétent.
ר המוצ סילוק !
אזהרה .
המדינה וחוקי להנחיות בהתאם להיות חייב זה מוצר של סופי סילוק 2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
ة ي لىطن ا ئح ا ى ل ل ا و ن ني ا لقى ا ع ي جم ل وفقا ه مع ل لتعام ا نبغي ي نتج م ل ا ا ذ ه ن م لنهائي ا ص ل لتخ ا ند ع 경고!
이 제품은 해당 국가의 관련 법규 및 규정에 따라 폐기되어야 합니다.
Waarschuwing
De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming
met alle nationale wetten en reglementen.
2-2 Static-Sensitive Devices
Electrostatic-Discharge (ESD) can damage electronic components. To avoid dam-
aging your system board, it is important to handle it very carefully. The following
measures are generally sufficient to protect your equipment from ESD.
Precautions
•
•
Use a grounded wrist strap designed to prevent static discharge.
Touch a grounded metal object before removing the board from the antistatic
bag.
•
Handle the board by its edges only; do not touch its components, peripheral
chips, memory modules or gold contacts.
•
•
When handling chips or modules, avoid touching their pins.
Put the motherboard and peripherals back into their antistatic bags when not in
use.
•
•
For grounding purposes, make sure your computer chassis provides excellent
conductivity between the power supply, the case, the mounting fasteners and
the motherboard.
Use only the correct type of onboard CMOS battery. Do not install the onboard
battery upside down to avoid possible explosion.
Unpacking
The motherboard is shipped in antistatic packaging to avoid static damage. When
unpacking the board, make sure that the person handling it is static protected.
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
2-3 Processor and Heatsink Installation
Warning: When handling the processor package, avoid placing direct pressure on the
label area of the fan.
Important:
Always connect the power cord last, and always remove it before adding,
removing or changing any hardware components. Make sure that you in-
stall the processor into the CPU socket before you install the CPU heatsink.
If you buy a CPU separately, make sure that you use an Intel-certified
multi-directional heatsink only.
Make sure to install the system board into the chassis before you install
the CPU heatsink.
When receiving a server board without a processor pre-installed, make
sure that the plastic CPU socket cap is in place and none of the socket
pins are bent; otherwise, contact your retailer immediately.
Refer to the Supermicro website for updates on CPU support.
Installing the LGA1150 Processor
1. Press the load lever to release the load plate, which covers the CPU socket,
from its locking position.
Load Plate
Load Lever
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
2. Gently lift the load lever to open the load plate. Remove the plastic cap.
3. Use your thumb and your index finger to hold the CPU at the North center
edge and the South center edge of the CPU.
North Center Edge
South Center Edge
4. Align the CPU key that is the semi-circle cutouts against the socket keys.
Once it is aligned, carefully lower the CPU straight down into the socket. (Do
not drop the CPU on the socket. Do not move the CPU horizontally or verti-
cally.
2-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
5. Do not rub the CPU against the surface or against any pins of the socket to
avoid damaging the CPU or the socket.)
6. With the CPU inside the socket, inspect the four corners of the CPU to make
sure that the CPU is properly installed.
7. Use your thumb to gently push the load lever down to the lever lock.
CPU properly
installed
Load lever locked
into place
Warning: You can only install the CPU inside the socket only in one direction. Make
sure that it is properly inserted into the CPU socket before closing the load plate. If it
doesn't close properly, do not force it as it may damage your CPU. Instead, open the
load plate again and double-check that the CPU is aligned properly.
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
Installing an Active CPU
Heatsink with Fan
1. Locate the CPU Fan power connec-
tor on the motherboard. (Refer to
the layout on the right for the CPU
Fan location.)
2. Position the heatsink so that the
heatsink fan wires are closest to the
CPU fan power connector and are
not interfered with other compo-
nents.
Thermal Grease
3. Inspect the CPU Fan wires to make
sure that the wires are routed
through the bottom of the heatsink.
4. Remove the thin layer of the protec-
Heatsink
Fins
tive film from the heatsink.
Warning: CPU overheat may occur if the
protective film is not removed from the
heatsink.
5. Apply the proper amount of thermal
grease on the CPU.
Note: If your heatsink came with
a thermal pad, please ignore
this step.
6. If necessary, rearrange the wires
to make sure that the wires are not
pinched between the heatsink and
the CPU. Also make sure to keep
clearance between the fan wires
and the fins of the heatsink.
Recommended Supermicro
heatsink:
SNK-P0046A4 active heatsink
2-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
7. Align the four heatsink fasten-
ers with the mounting holes
on the motherboard. Gently
push the pairs of diagonal
fasteners (#1 & #2, and #3 &
#4) into the mounting holes
until you hear a click. Also,
make sure to orient each
fastener so that the narrow
end of the groove is pointing
outward.
8. Repeat Step 7 to insert all
four heatsink fasteners into
the mounting holes.
9. Once all four fasteners are
securely inserted into the
mounting holes, and the heat-
sink is properly installed on
the motherboard, connect the
heatsink fan wires to the CPU
Fan connector.
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
Removing the Heatsink
Warning: We do not recommend that the
CPU or the heatsink be removed. However, if
you do need to remove the heatsink, please
follow the instructions below to remove the
heatsink and to prevent damage done to the
CPU or other components.
Active Heatsink Removal
1. Unplug the power cord from the
power supply.
Unplug the
PWR cord
2. Disconnect the heatsink fan wires
from the CPU fan header.
3. Use your finger tips to gently press
on the fastener cap and turn it
counterclockwise to make a 1/4 (900)
turn, and pull the fastener upward to
loosen it.
4. Repeat Step 3 to loosen all fasteners
from the mounting holes.
5. With all fasteners loosened, remove
the heatsink from the CPU.
Pull Up
2-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
2-4 Installing DDR3 Memory
Note: Check the Supermicro website for recommended memory mod-
ules.
CAUTION
Exercise extreme care when installing or removing DIMM
modules to prevent any possible damage.
DIMM Installation
MH1
MH2
U103
68
18
52
34
51
JPAC1
1
FAN5
4
JAUDIO1
3
1
JUSB01
JHDMI
1
JSPDIF_OUT
JUSBLAN2
JUSBLAN1
USB 14/15
USB 16/17
USB 6/7(3.0)
LAN1
JPAC1:AUDIO
1-2:ENABLE
2-3:DISABLE
USB 4/5(3.0)
LAN2
JL2
JPL2
1-2 ENABLE
2-3 DISABLE
LAN2
PCIE1
JPCIE2
PCIE3
JPCIE4
PCIE5
JPCIE6
1
1. Insert the desired number of DIMMs
into the memory slots, starting with
P1-DIMMA2 (see the next page for
the location). For the system to work
properly, please use the memory
modules of the same type and speed
in the same motherboard.
JPL2
JI2C1/JI2C2
ON:ENABLE
OFF:DISABLE
JI2C2
JI2C1
1
JVR1
1
1
J1394_1
3
4
1
JPL1 LAN1
1-2 ENABLE
2-3 DISABLE
A
CPU
J1
C
CPU
JCOM1
1
BIOS LICENSE
A
C
5
OC3_LED
2
1
1
4
10
LED3
6
10
LED2
6
2
JPME1:
1-2:NORMAL
2-3:ME RECOVERY
JWD1:
1-2:RST
2-3:NMI
WA
T
C
H
D
O
G
JWOR1:
AKE ON RING
W
Tested to Comply
With FCC Standards
MH6
MH7
P1-DIMMA1
P1-DIMMA2
P1-DIMMB1
P1-DIMMB2
FOR HOME OR OFFICE USE
19
JWD1 20
ALWAYS POPULATE BLUE SOCKET FIRST
UNB NON-ECC DDR3 DIMM REQUIRED
3
3
MH4
1
JPME1
1
3
R298
JBT1
1
USB4/5
USB6/7
7
10
2
1
JPME2
1
1
7
JBR1:
USB12/13
USB 0/1(3.0)
JBR1
10
1-2:NORMAL
JUSB30_I
1
2-3:BIOS RECOVERY
10
SP1
2USB8/9
1
2
2
1
1
1
19
11
+
J
S
D
1
:
S
A
DOM PWR
+
7
3
U196 U197
USB 2/3
7
8
7
USB 2/3(3.0)
JLED1:
PIN POWER LED
2
JUSB30_I1
LED1
1
C
3
I-SATA0
I-SATA1
I-SATA2
A-SATA0
JSD1
JPW1
1
1
4
RT1
JD1
7
1
JOCE
4
10
16
4
1
JF1
PWR
ON
1
1
JD1:
SPEAKER:1-4
BUZZER:3-4
MH5
3
OH/FF
LED
HDD PWR
LED LED
1
6
4
RST
N
I
C
2
N
I
C
1
JF1
1
JLED1
MH9
X
JL1:
CHASSIS INTRUSION
MH8
2. Push the release tabs outwards on
both ends of the DIMM slot to unlock
it.
3. Align the key of the DIMM mod-
ule with the receptive point on the
memory slot.
4. Align the notches on both ends of
the module against the receptive
points on the ends of the slot.
Notches
5. Use two thumbs together to press
the notches on both ends of the
module straight down into the slot
until the module snaps into place.
Release Tabs
6. Press the release tabs to the lock
positions to secure the DIMM module
into the slot.
Press both notches
straight down into
the memory slot.
Removing Memory Modules
Reverse the steps above to remove the
DIMM modules from the motherboard.
2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
Memory Support
The C7Z87-OCE supports up to 32GB of Unbuffered (UDIMM) DDR3 Non-ECC
1600/1333/1066 MHz in 4 memory slots. Populating these DIMM modules with a
Towards the CPU
P1-DIMMA1
P1-DIMMA2 (Blue Slot)
P1-DIMMB1
P1-DIMMB2 (Blue Slot)
Towards the edge of the motherboard
pair of memory modules of the same type and same size will result in interleaved
memory, which will improve memory performance. Please refer to the table below:
Memory Population Guidelines
Please follow the table below when populating the C7Z87.
DDR3 Unbuffered Non-ECC (UDIMM) Memory
DIMM Slots per
Channel
DIMMs Populat-
ed per Channel
DIMM Type
POR Speeds
1066, 1333, 1600
1066, 1333, 1600
Ranks per DIMM (any
combination)
2
1
Unbuffered
DDR3
Single Rank, Dual Rank
2
2
Unbuffered
DDR3
Single Rank, Dual Rank
Notes
•
•
Be sure to use memory modules of the same type, same speed, same
frequency on the same motherboard. Mixing of memory modules of dif-
ferent types and speeds is not allowed.
Due to memory allocation to system devices, the amount of memory that
remains available for operational use will be reduced when 4 GB of RAM
is used. The reduction in memory availability is disproportional. See the
following table for details.
2-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
•
For Microsoft Windows users: Microsoft implemented a design change in the
Windows XP with Service Pack 2 (SP2) and Windows Vista. This change is
specific to the behavior of Physical Address Extension (PAE) mode which
improves driver compatibility. For more information, please read the following
article at Microsoft’s Knowledge Base website at: http://support.microsoft.
com/kb/888137.
Possible System Memory Allocation & Availability
System Device
Size
Physical Memory
Remaining (-Available)
(4 GB Total System
Memory)
Firmware Hub flash memory (System BIOS)
Local APIC
1 MB
3.99
4 KB
3.99
3.99
3.99
3.76
3.51
3.01
Area Reserved for the chipset
I/O APIC (4 Kbytes)
2 MB
4 KB
PCI Enumeration Area 1
PCI Express (256 MB)
256 MB
256 MB
512 MB
PCI Enumeration Area 2 (if needed) -Aligned on 256-MB
boundary-
VGA Memory
16 MB
1 MB
2.85
2.84
2.84
TSEG
Memory available to OS and other applications
Memory Population Guidelines
When installing memory modules, the DIMM slots should be populated in the following
order: P1-DIMMA2, P1-DIMMB2, then P1-DIMMA1, P1-DIMMB1.
•
•
Always use DDR3 DIMM modules of the same size, type and speed.
Mixed DIMM speeds can be installed. However, all DIMMs will run at the speed
of the slowest DIMM.
Recommended Population (Balanced)
DIMMA2
2GB
DIMMB2
2GB
DIMMA1
DIMMB1
Total System Memory
4GB
8GB
2GB
2GB
2GB
2GB
4GB
4GB
8GB
4GB
4GB
4GB
4GB
16GB
16GB
32GB
8GB
8GB
8GB
8GB
8GB
8GB
2-13
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
2-5 Motherboard Installation
All motherboards have standard mounting holes to fit different types of chassis.
Make sure that the locations of all the mounting holes for both motherboard and
chassis match. Although a chassis may have both plastic and metal mounting fas-
teners, metal ones are highly recommended because they ground the motherboard
to the chassis. Make sure that the metal standoffs click in or are screwed in tightly.
Then use a screwdriver to secure the motherboard onto the motherboard tray.
Tools Needed
Philips Screwdriver
(1)
Standoffs (9)
Only if Needed
Philips Screws (9)
Location of Mounting Holes
Caution: 1) To avoid damaging the motherboard and its components, please do
not use a force greater than 8 lb/inch on each mounting screw during motherboard
installation. 2) Some components are very close to the mounting holes. Please take
precautionary measures to avoid damaging these components when installing the
motherboard to the chassis.
2-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
Installing the Motherboard
1. Install the I/O shield into the back of the chassis.
2. Locate the mounting holes on the motherboard. (See the previous page.)
3. Locate the matching mounting holes on the chassis. Align the mounting holes
on the motherboard against the mounting holes on the chassis.
4. Install standoffs in the chassis as needed.
5. Install the motherboard into the chassis carefully to avoid damaging other
motherboard components.
6. Using the Phillips screwdriver, insert a Phillips head #6 screw into a mounting
hole on the motherboard and its matching mounting hole on the chassis.
7. Repeat Step 5 to insert #6 screws into all mounting holes.
8. Make sure that the motherboard is securely placed in the chassis.
Note: Images displayed are is for illustration only. Your chassis or compo-
nents might look different from those shown in this manual.
2-15
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
2-6 Connectors/IO Ports
The I/O ports are color coded in conformance with the PC 99 specification. See the
figure below for the colors and locations of the various I/O ports.
Backplane I/O Panel
N
O
Q
R
A
B
K
L
H
I
D
F
P
S
E
M
G
J
C
Backplane I/O Panel
H. Gb LAN Port 1
I. USB 3.0 Port 6
A. USB 2.0 Port 0
N. Center/LFE Out
O. Surround Out
P. S/PDIF Out
Q. Line In
B. USB 2.0 Port 1
C. HDMI Port
J. USB 3.0 Port 7
K. Gb LAN Port 2
HD Audio
D. VGA Port
E. DVI Port
L. USB 3.0 Port 4
M. USB 3.0 Port 5
R. Line Out
F. Thunderbolt Port
G. CMOS Reset
S. Mic In
2-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
Universal Serial Bus (USB)
Two Universal Serial Bus 2.0 ports (0/1) and four USB 3.0 ports (4/5,6/7) are located
on the I/O back panel. In addition, two USB 2.0 headers (four ports: 4/5, 6/7), and
two USB 3.0 headers (four ports: 0/1, 2/3) are also located on the motherboard
to provide front chassis access using USB cables (not included). See the tables
below for pin definitions.
Front Panel USB (2.0) #4/5, 6/7
Back Panel USB (2.0) #0/1
Pin Definitions
Pin Definitions
Pin #
Definition
+5V
Pin #
Definition
+5V
Pin# Definition Pin#
Definition
+5V
1
3
5
7
9
2
1
2
3
4
+5V
5
6
7
8
USB_PN2
USB_PP2
Ground
Key
4
USB_PN3
USB_PP3
Ground
USB_PN1
USB_PP1
Ground
USB_PN0
USB_PP0
Ground
6
8
10
Ground
A. Backpanel USB 2.0 #0
B. Backpanel USB 2.0 #1
C. Backpanel USB 3.0 #6
D. Backpanel USB 3.0 #7
E. Backpanel USB 3.0 #4
F. Backpanel USB 3.0 #5
G. USB 2.0 Header #4/5
H. USB 2.0 Header #6/7
I. USB 3.0 Header #2/3
J. USB 3.0 Header #0/1
Front Panel USB (3.0) #0/1, 2/3
Pin Definitions
Pin# Pin#
Signal Name
Description
1
2
3
10
11
12
VBUS
D-
Power
USB 2.0 Differential Pair
D+
4
5
6
7
8
9
13
14
15
16
17
18
Ground
Ground of PWR Return
SuperSpeed Receiver
StdA_SSRX-
StdA_SSRX+ Differential Pair
GND_DRAIN
StdA_SSTX-
StdA_SSTX+
Ground for Signal Return
SuperSpeed Transmitter
Differential Pair
A
B
E
C
D
F
G
H
J
I
2-17
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
Ethernet Ports
LAN Ports
Pin Definition
Two Gigabit Ethernet ports (LAN1/
LAN2) are located next to the
HD Audio Connector on the I/O
Backpanel to provide network con-
nections. These ports accept RJ45
type cables.
Pin# Definition
1
2
3
4
P2V5SB
TD0+
10
11
12
13
SGND
Act LED
TD0-
P3V3SB
TD1+
Link 100 LED
(Green, +3V3SB)
5
TD1-
14
Link 1000 LED
(Yellow, +3V3SB)
Note: Please refer to the
LED Indicator Section for
LAN LED information.
6
7
8
9
TD2+
TD2-
TD3+
TD3-
15
16
17
88
Ground
Ground
Ground
Ground
(NC: No Connection)
Back Panel High Definition
Audio (HD Audio)
(BP) HD Audio
Conn# Signal
This motherboard features a 7.1+2
Channel High Definition Audio
(HDA) codec that provides 10
DAC channels. The HD Audio con-
nections simultaneously supports
multiple-streaming 7.1 sound play-
back with 2 channels of independent
stereo output through the front panel
stereo out for front, rear, center
and subwoofer speakers. Use the
Advanced software included in the
CD-ROM with your motherboard to
enable this function.
SPDIF_In/Out
A
B
C
D
E
F
Surround_Out
CEN/LFE_Out
Mic_In
Line_Out
Line_In
A. LAN1
B. LAN2
C. SPDIF_In/Out
D. Surround_Out
E. CEN/LFE_Out
F. Mic_In
G. Line-Out
H. Line_In
E
H
A
B
D
G
F
C
2-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
HDMI Port
One HDMI (High-Definition Multimedia In-
terface) is located next to the VGA port on
the I/O backpanel. This connector is used to
display both high definition video and digital
sound through an HDMI capable display,
using a single HDMI cable (not included).
VGA Port
A VGA port is located next to the USB ports
0/1 on the I/O backpanel. Use this port to
connect to a compatible VGA display.
DVI Port
A DVI port is located just under the VGA
port on the I/O backpanel. Use this port to
connect to a compatible DVI (Digital Visual
Interface) display.
A. HDMI Port
B. VGA Port
C. DVI Port
B
A
C
2-19
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
Thunderbolt Interface
This motherboard supports one Thunderbolt
interface on the backpanel. A Thunderbolt
interface is a hardware interface that allows
peripherals to be connected to the mother-
board at transfer speeds of up to 10Gbit/s.
This port combines a PCIe and a DisplayPort
into one serial signal.
A. Thunderbolt Interface
CMOS Reset/Clear
B. CMOS Reset Button (Backpanel)
C. CMOS Reset Pads (JBT1) Onboard)
D. CMOS Reset Button (Onboard)
This motherboard supports three momen-
tary hardware switches to clear or reset the
CMOS memory back to its default values.
These switches are located at different
locations on the motherboard for maximum
convenience. The switches located at A
and B are momentary push buttons while C
(JBT1) is made up of two contact pads that
need to be shorted with a metallic obect (i.e.,
screwdriver, etc).
A
B
C
D
2-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
Front Control Panel
JF1 contains header pins for various buttons and indicators that are normally located
on a control panel at the front of the chassis. These connectors are designed spe-
cifically for use with Supermicro chassis. See the figure below for the descriptions
of the front control panel buttons and LED indicators. Refer to the following section
for descriptions and pin definitions.
LED_Anode+
Power LED
HDD LED
NIC1 LED
LED_Anode+
LED_Anode+
LED_Anode+
Pin 16
Pin 15
NIC2 LED
OH/Fan Fail LED
LED_Anode+
X
X
Reset
PWR
Reset Button
Ground
Ground
Power Button
Pin 2
Pin 1
2
1
JF1 Header Pins
2-21
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
Front Control Panel Pin Definitions
Power LED
Power LED
Pin Definitions (JF1)
The Power LED connection is located on
pins 15 and 16 of JF1. Refer to the table
on the right for pin definitions.
Pin# Definition
15
16
+5V
Ground
HDD LED
HDD LED
Pin Definitions (JF1)
The HDD LED connection is located on
pins 13 and 14 of JF1. Attach a cable
here to indicate the status of HDD-related
activities, including IDE, SATA activities.
See the table on the right for pin defini-
tions.
Pin# Definition
13
14
+5V
HD Active
LAN1/LAN2 LED
Pin Definitions (JF1)
NIC1/NIC2 (LAN1/LAN2)
Pin# Definition
The NIC (Network Interface Controller)
LED connection for LAN port 1 is located
on pins 11 and 12 of JF1, and the LED
connection for LAN Port 2 is on Pins 9
and 10. NIC1 LED and NIC2 LED are
2-pin NIC LED headers. Attach NIC LED
cables to NIC1 and NIC2 LED indicators
to display network activities. Refer to the
table on the right for pin definitions.
9/11
Vcc
10/12 Ground
OH/Fan Fail LED
Pin Definitions (JF1)
Pin# Definition
7
8
Vcc/Blue UID LED
OH/Fan Fail LED
OH/Fan Fail Indicator
Status
Overheat (OH)/Fan Fail
State Definition
Connect an LED cable to OH/Fan Fail
connections on pins 7 and 8 of JF1 to
provide warnings for chassis overheat/
fan failure. Refer to the table on the right
for pin definitions.
Off
On
Normal
Overheat
Fan Fail
Flash-
ing
A. PWR LED
LED_Anode+
Power LED
HDD LED
NIC1 LED
NIC2 LED
A
B
B. HDD LED
LED_Anode+
LED_Anode+
LED_Anode+
C. NIC1 LED
D. NIC2 LED
E. OH/Fan Fail
C
D
OH/Fan Fail LED
LED_Anode+
X
E
X
Reset
PWR
Reset Button
Power Butto
Ground
Ground
2
1
2-22
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
Reset Button
Reset Button
Pin Definitions (JF1)
The Reset Button connection is located
on pins 3 and 4 of JF1. Attach it to a hard-
ware reset switch on the computer case
to reset the system. Refer to the table on
the right for pin definitions.
Pin# Definition
3
4
Reset
Ground
Power Button
Power Button
Pin Definitions (JF1)
The Power Button connection is located
on pins1 and 2 of JF1. Momentarily con-
tacting both pins will power on/off the sys-
tem. This button can also be configured
to function as a suspend button (with a
setting in the BIOS - see Chapter 4). To
turn off the power in the suspend mode,
press the button for at least 4 seconds.
Refer to the table on the right for pin
definitions.
Pin# Definition
1
2
Signal
+3V Standby
A. Reset Button
B. PWR Button
LED_Anode+
Power LED
HDD LED
NIC1 LED
LED_Anode+
LED_Anode+
LED_Anode+
NIC2 LED
OH/Fan Fail LED
LED_Anode+
X
X
A
B
Reset
PWR
Reset Button
Power Button
Ground
Ground
2
1
2-23
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
2-7 Connecting Cables
This section provides brief descriptions and pin-out definitions for onboard headers
and connectors. Be sure to use the correct cable for each header or connector. For
information on Backpanel USB and Front Panel USB ports, refer to Page 2-17. For
Front Panel Audio, please refer to Page 2-19.
ATX Power 24-pin Connector
Pin Definitions (JPW1)
ATX Main PWR & CPU PWR
Connectors (JPW1 & JPW2)
Pin# Definition
Pin #
1
Definition
+3.3V
+3.3V
COM
13
14
15
16
17
18
19
20
21
22
23
24
+3.3V
-12V
The 24-pin main power connector
(JPW1) is used to provide power to
the motherboard. The 8-pin CPU
PWR connector (JPW2) is also
required for the processor. These
power connectors meet the SSI EPS
12V specification. See the table on
the right for pin definitions.
2
COM
PS_ON
COM
COM
COM
Res (NC)
+5V
3
4
+5V
5
COM
6
+5V
7
COM
8
PWR_OK
5VSB
+12V
9
+5V
10
11
12
+5V
+12V
COM
+3.3V
12V 8-pin Power Connec-
tor Pin Definitions
Pins
Definition
Ground
+12V
1 through 4
5 through 8
24-Pin Main PWR
(Required)
B
A. 24-Pin ATX Main PWR
B. 8-Pin PWR
A
2-24
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
Fan Headers (Fan 1 ~ Fan 5)
Fan Header
Pin Definitions
The C7Z87-OCE has five fan headers (Fan
1~Fan 5). These fans are 4-pin fan head-
ers. Although pins 1-3 of the fan headers are
backward compatible with the traditional 3-pin
fans, we recommend the use 4-pin fans to take
advantage of the fan speed control via IPMI
interface. This allows the fan speeds to be au-
tomatically adjusted based on the motherboard
temperature. Refer to the table on the right for
pin definitions.
Pin# Definition
1
2
Ground (Black)
2.5A/+12V
(Red)
3
4
Tachometer
PWM_Control
Chassis Intrusion
Pin Definitions (JL1)
Chassis Intrusion (JL1)
Pin# Definition
A Chassis Intrusion header is located at JL1 on
the motherboard. Attach the appropriate cable
from the chassis to inform you of a chassis intru-
sion when the chassis is opened.
1
2
Intrusion Input
Ground
A. Fan 1 (CPU Fan)
B. Fan 2
C. Fan 3
D. Fan 4
E. Fan 5
F. Chassis Intrusion
E
D
A
B
F
C
2-25
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
Internal Buzzer (SP1)
Internal Buzzer
Pin Definition
The Internal Buzzer (SP1) can be
used to provide audible indications for
various beep codes. See the table on
the right for pin definitions.
Pin#
Pin 1
Pin 2
Definitions
Pos. (+)
Beep In
Neg. (-)
Alarm
Speaker
Speaker (JD1)
Speaker Connector
Pin Definitions
On the JD1 header, Pins 3~4 are used
for internal speaker. Close pins 3~4
with a cap to use the onboard speaker.
If you wish to use an external speaker,
close pins 1~4 with a cable. See the
table on the right for pin definitions.
Pin Setting Definition
Pins 3~4
Pins1~4
Internal Speaker
External Speaker
A. Internal Buzzer
B. Speaker Header
A
B
2-26
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
Onboard Power LED (JLED1)
Onboard PWR LED
Pin Definitions
An onboard Power LED header is lo-
cated at JLED1. This Power LED header
is connected to Front Control Panel
located at JF1 to indicate the status of
system power. See the table on the right
for pin definitions.
Pin# Definition
1
2
VCC
No Connection
3
Connection to PWR
LED in JF1
Serial/COM Ports
Pin Definitions
Serial Port (COM1)
There is one serial (COM) port header
on the motherboard. COM1 is located
next to the 1394 connection header.
See the table on the right for pin defi-
nitions.
Pin #
Definition
Pin #
Definition
1
2
3
4
5
DCD
RXD
6
7
8
9
DSR
RTS
CTS
RI
TXD
DTR
Ground
10
N/A
A. PWR LED
B. COM1
B
A
2-27
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
DOM PWR Connector (JSD1)
DOM PWR
Pin Definitions
The Disk-On-Module (DOM) power
connector, located at JSD1, provides
5V (Gen1/Gen) power to a solid state
DOM storage device connected to one
of the SATA ports. See the table on the
right for pin definitions.
Pin# Definition
1
2
5V
Ground
3
Ground
SPDIF OUT (JSPDIF_OUT)
SPDIF_OUT
Pin Definitions
The SPDIF Out (JSPDIF_OUT) is
used for digital audio output. You will
also need the appropriate cable to use
these features.
Pin# Definition
1
2
S/PDIF_Out
Ground
A.DOM PWR
B. S/PDIF OUt
B
A
2-28
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
Standby Power Header
Standby Power
Pin Definitions
The Standby Power header is located
at STBY1 on the motherboard. See
the table on the right for pin defini-
tions.
Pin# Definition
1
2
3
+5V Standby
Ground
Wake-up
Chassis LED
If this motherboard will be mounted on
a Supermicro chassis, this header can
be used to attach the motherboard to
control the chassis' LED readout.
A. STBY PWR
B. JCHLED
B
A
2-29
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
TPM Header/Port 80 Header
TPM/Port 80 Header
Pin Definitions
A Trusted Platform Module/Port 80
header is located at JTPM1 to provide
TPM support and Port 80 connection.
Use this header to enhance system
performance and data security. See
the table on the right for pin defini-
tions.
Pin #
1
Definition
Pin #
Definition
GND
LCLK
2
4
6
8
3
LFRAME#
LRESET#
LAD 3
<(KEY)>
+5V (X)
5
7
LAD 2
9
+3.3V
10
12
14
16
18
20
LAD1
11
13
15
17
19
LAD0
GND
SMB_CLK4
+3V_DUAL
GND
SMB_DAT4
SERIRQ
CLKRUN# (X)
LDRQ# (X)
LPCPD#
A. TPM/Port 80
A
2-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
Front Panel Audio Header (AUDIO FP)
10-in Audio
Pin Definitions
A 10-pin Audio header is supported on the
motherboard. This header allows you to
connect the motherboard to a front panel
audio control panet, if needed. Connect an
audio cable to the audio header to use this
feature (not supplied). See the table at right
for pin definitions for the header.
Pin# Signal
1
2
3
4
5
6
7
8
9
10
Microphone_Left
Audio_Ground
Microphone_Right
Audio_Detect
Line_2_Right
Ground
Jack_Detect
Key
Line_2_Left
Ground
A. AUDIO FP
A
2-31
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
2-8 Jumper Settings
Explanation of Jumpers
To modify the operation of the mother-
board, jumpers can be used to choose
between optional settings. Jumpers create
shorts between two pins to change the
function of the connector. Pin 1 is identified
with a square solder pad on the printed
circuit board.
Note: On two-pin jumpers,
"Closed" means the jumper is on,
and "Open" means the jumper is
off the pins.
LAN1/LAN2 Enable/Disable
GLAN Enable
Jumper Settings
Jumpers JPL1/JPL2 enable or disable
LAN ports 1/2 on the motherboard. See
the table on the right for jumper settings.
The default setting is enabled.
Pin# Definition
1-2
2-3
Enabled (default)
Disabled
A. JPL1: LAN1 Enable
B. JPL2: LAN2 Enable
B
A
2-32
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
CMOS Clear (JBT1)
JBT1 is used to clear the saved system setup configuration stored in the CMOS
chip. To clear the contents of the CMOS, completely shut down the system, remove
the AC power cord and then short JBT1 with a jumper. Remove the jumper before
powering on the system again. This will erase all user settings and revert everything
to their factory-set defaults.
PCI Slot SMB Enable (I2C1/I2C2)
PCI Slot_SMB Enable
Jumper Settings
Use Jumpers I2C1/I2C2 to enable PCI
Jumper Setting Definition
SMB (System Management Bus) support
Short
Enabled
Disabled
to improve system management for the
PCI slots. See the table on the right for
jumper settings.
Open (Default)
A. Clear CMOS
B. JI2C1
C. JI2C2
B
C
A
2-33
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
Audio Enable (JPAC1)
Audio Enable/Disable
Jumper Settings
JPAC1 allows you to enable or disable
the onboard audio support. The default
position is on pins 1 and 2 to enable on-
board audio connections. See the table
on the right for jumper settings.
Both Jumpers Definition
Pins 1-2
Pins 2-3
Enabled
Disabled
Watch Dog
Jumper Settings
Watch Dog Enable/Disable
Watch Dog (JWD1) is a system moni-
tor that can reboot the system when a
software application hangs. Close pins
1-2 to reset the system if an applica-
tion hangs. Close pins 2-3 to generate
a non-maskable interrupt signal for the
application that hangs. See the table on
the right for jumper settings. Watch Dog
must also be enabled in the BIOS.
Jumper Setting Definition
Pins 1-2
Pins 2-3
Open
Reset (default)
NMI
Disabled
A. Audio Enable
B. Watch Dog Enable
A
B
2-34
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
USB Wake-Up (JPUSB 1/2)
USB Wake-Up
Jumper Settings
Use jumper JPUSB1 to activate the "wake-
up" function of the USB ports by pressing
a key on a USB keyboard or clicking the
USB mouse connected. This jumper is used
together with a USB Wake-Up feature in the
BIOS. Enable this jumper and the USB sup-
port in the BIOS to wake up your system via
USB devices.
Jumper Setting Definition
Pins 1-2
Pins 2-3
Enabled
Disabled (Default)
Note: Use JPUSB1 for the USB ports on
the back panel, and JPUSB2 for the front
panel USB headers.
Over-Clocking Buttons
Switch Settings
Over-Clocking Buttons (OC1,OC2, OC3)
Press these buttons to activate the over-
clocking feature of the motherboard. These
buttons will allow the CPU to run above its
rated speed. This is an advanced feature and
should only be used by experienced users.
Also, refer to the CMOS Reset/Clear features
on page 2-20 for related information.
Switch Setting Definition
OC1 On
OC2 On
OC3 On
15% Over-Clock
20-25% Over-Clock
User Defined (BIOS)
A
B
2-35
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
Management Engine (ME) Recovery
(JPME1)
ME Recovery (JPME1)
Jumper Settings
Pin# Definition
Use Jumper JPME1 to select ME frmware
Recovery mode, which will limit resource
allocation for essential systemoperation
only in order to maintain normal power
operation and management. In the single
operation mode, online upgrade will be
available via Recovery mode. See the
table on the right for jumper settings.
1-2
2-3
Normal (Default)
ME Recovery
Manufacture Mode (JPME2)
Jumper Settings
Manufacture Mode (JPME2)
Close Pin 2 and Pin 3 of Jumper JPME2
to bypass SPI flash security and force
the system to operate in the Manufacture
Mode, allowing the user to flash the sys-
tem firmware from a host server for sys-
tem setting modifications. See the table
on the right for jumper settings.
Pin# Definition
1-2
2-3
Normal (Default)
Manufacture Mode
A. ME Recovery Mode
B. Manufacture Mode
A
B
2-36
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
BIOS Recovery (JBR1)
BIOS Recovery (JBR1)
Jumper Settings
The BIOS Recovery (JBR1) is used to en-
able or disable the BIOS Recovery feature
of the motherboard. Install the jumper on
pins 2-3 to begin the recovery process.
See Appendix D for related information.
Pin# Definition
1-2
2-3
Normal (Default)
Recover
Power Button
Manufacture Mode (JPME2)
Jumper Settings
In addition to the soft power switch
provided in JF1, your motherboard is
equipped with a 'soft' power button on the
motherboard. This switch works the same
way as the soft power switch on JF1.
Pin# Definition
1-2
2-3
Normal (Default)
Manufacture Mode
A. BIOS Recovery
B. Power Button
B
A
2-37
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
2-9 Onboard Indicators
LAN1
LAN2
LAN 1/LAN 2 LEDs
Link LED
Activity LED
Two LAN ports (LAN 1/LAN 2) are
located on the I/O backplane of the
motherboard. Each Ethernet LAN
port has two LEDs. The yellow LED
indicates activity, while the Link
LED may be green, amber, or off
to indicate the speed of the con-
nections. See the tables at right for
more information.
GLAN 1/2 Activity Indicator
LED Settings
Color
Yellow
Status
Definition
Active
Flashing
GLAN Ports 1/2 Link Indicator
LED Settings
LED Color Definition
Off
No Connection/10 Mbps/100
Mbps
Amber
Green
1 Gbps
10 Gbps.
Onboard Power LED (LED1)
An Onboard Power LED is located
at LED1 on the motherboard. When
LED1 is on, the AC power cable is
connected. Make sure to disconnect
the power cable before removing or
installing any component. See the
layout below for the LED location.
Onboard PWR LED Indicator
LED Status
Status
Definition
Off
On
System Off
System on, or
System off and PWR
Cable Connected
A. LAN 1/2 LEDs
B. PWR LED
B
A
2-38
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
Status Display (LED3,LED2)
LED3 and LED2 are alpha-numeric
displays that will display a status or
POST code when the motherboard
is powered on. Please download
the following AMI publication for a
complete list of POST codes:
http://www.ami.com/support/doc/ami_aptio_4.x_status_codes_pub.pdf
A. Status Display
A
2-39
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
2-10 SATA Connections
SATA Connections (I-SATA0~I-SATA5)
Eight Serial ATA (SATA) 3.0 connectors (I-SATA 0~5, A-SATA 0/1) are supported on
the board. The I-SATA 3.0 ports are supported by the Intel Z87 PCH chip (supports
RAID 0,1,5,10) while the A-SATA 3.0 ports are provided by the ASMedia SATA Con-
troller. These Serial Link connections provide faster data transmission than legacy
Parallel ATA. See the table on the right for pin definitions.
Top
SATA 2.0/3.0 Connectors
Pin Definitions
A. I-SATA 3.0 #0
B. I-SATA 3.0 #2
C. I-SATA 3.0 #4
D. A-SATA 3.0 #0
Bottom
Pin# Signal
1
2
3
4
5
6
7
Ground
SATA_TXP
SATA_TXN
Ground
E. I-SATA 3.0 #1
F. I-SATA 3.0 #3
G. I-SATA 3.0 #5
H. A-SATA 3.0 #1
SATA_RXN
SATA_RXP
Ground
(Top)
A
E
B
C
D
H
G
F
(Bottom)
2-40
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Troubleshooting
Chapter 3
Troubleshooting
3-1 Troubleshooting Procedures
Use the following procedures to troubleshoot your system. If you have followed all
of the procedures below and still need assistance, refer to the ‘Technical Support
Procedures’ and/or ‘Returning Merchandise for Service’ section(s) in this chapter.
Always disconnect the AC power cord before adding, changing or installing any
hardware components.
Before Power On
1. Make sure that the Standby PWR LED is not on. (Note: If it is on, the
onboard power is on. Be sure to unplug the power cable before installing or
removing the components.)
2. Make sure that there are no short circuits between the motherboard and
chassis.
3. Disconnect all ribbon/wire cables from the motherboard, including those for
the keyboard and mouse. Also, be sure to remove all add-on cards.
4. Install a CPU and heatsink (-be sure that it is fully seated) and then connect
the chassis speaker and the power LED to the motherboard. Check all jumper
settings as well.
No Power
1. Make sure that there are no short circuits between the motherboard and
chassis.
2. Make sure that all jumpers are set to their default positions.
3. Check if the 115V/230V switch on the power supply is properly set.
4. Turn the power switch on and off to test the system.
5. The battery on your motherboard may be old. Check to make sure that it still
supplies ~3VDC. If it does not, replace it with a new one.
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
No Video
1. If the power is on, but you have no video--in this case, you will need to re-
move all the add-on cards and cables first.
2. Use the speaker to determine if any beep codes exist. (Refer to Appendix A
for details on beep codes.)
3. Remove all memory modules and turn on the system. (If the alarm is on,
check the specifications of memory modules, reset the memory or try a differ-
ent one.)
Memory Errors
1. Make sure that the DIMM modules are properly installed and fully seated in
the slots.
2. You should be using unbuffered Non-ECC DDR3 (1.5V) 1600/1333/1066 MHz
memory recommended by the manufacturer. Also, it is recommended that you
use the memory modules of the same type and speed for all DIMMs in the
system. Do not use memory modules of different sizes, different speeds and
different types on the same motherboard.
3. Check for bad DIMM modules or slots by swapping modules between slots to
see if you can locate the faulty ones.
4. Check the switch of 115V/230V power supply.
Losing the System’s Setup Configuration
1. Please be sure to use a high quality power supply. A poor quality power sup-
ply may cause the system to lose CMOS setup information. Refer to Section
1-5 for details on recommended power supplies.
2. The battery on your motherboard may be old. Check to verify that it still sup-
plies ~3VDC. If it does not, replace it with a new one.
3. If the above steps do not fix the Setup Configuration problem, contact your
vendor for repairs.
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Troubleshooting
3-2 Technical Support Procedures
Before contacting Technical Support, please make sure that you have followed all
the steps listed below. Also, Note that as a motherboard manufacturer, Supermicro
does not sell directly to end users, so it is best to first check with your distributor or
reseller for troubleshooting services. They should know of any possible problem(s)
with the specific system configuration that was sold to you.
1. Please go through the ‘Troubleshooting Procedures’ and 'Frequently Asked
Question' (FAQ) sections in this chapter or see the FAQs on our website
(http://www.supermicro.com/support/faqs/) before contacting Technical Sup-
port.
2. BIOS upgrades can be downloaded from our website at (http://www.supermi-
cro.com/support/bios/).
Note: Not all BIOS can be flashed. Some cannot be flashed; it depends
on the boot block code of the BIOS.
3. If you've followed the instructions above to troubleshoot your system, and still
cannot resolve the problem, then contact Supermicro's technical support and
provide them with the following information:
•
•
Motherboard model and PCB revision number
BIOS release date/version (this can be seen on the initial display when your
system first boots up)
•
•
System configuration
An example of a Technical Support form is on our website at (http://www.su-
permicro.com/support/contact.cfm).
4. Distributors: For immediate assistance, please have your account number
ready when placing a call to our technical support department. We can be
reached by e-mail at [email protected], by phone at: (408) 503-
8000, option 2, or by fax at (408)503-8019.
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
3-3 Frequently Asked Questions
Question: What type of memory does my motherboard support?
Answer: The C7Z87-OCE supports up to 32GB of unbuffered Non-ECC DDR3
SDRAM (1.5V, 1600/1333/1066 MHz). See Section 2-4 for details on installing
memory.
Question: How do I update my BIOS?
Answer: We do NOT recommend that you upgrade your BIOS if you are not
experiencing any problems with your system. Updated BIOS files are located on
our website at http://www.supermicro.com/support/bios/. Please check our BIOS
warning message and the information on how to update your BIOS on our web
site. Select your motherboard model and download the BIOS ROM file to your
computer. Also, check the current BIOS revision to make sure that it is newer than
your BIOS before downloading. You may choose the zip file or the .exe file. If you
choose the zipped BIOS file, please unzip the BIOS file onto a bootable device or
a USB pen/thumb drive. To flash the BIOS, run the batch file named "ami.bat" with
the new BIOS ROM file from your bootable device or USB pen/thumb drive. Use
the following format:
F:\> ami.bat BIOS-ROM-filename.xxx <Enter>
Note: Always use the file named “ami.bat” to update the BIOS, and insert
a space between "ami.bat" and the filename. The BIOS-ROM-filename
will bear the motherboard name (i.e., C7Z87) and build version as the
extension. For example, "C7Z87.115". When completed, your system will
automatically reboot.
If you choose the .exe file, please run the .exe file under Windows to create
the BIOS flash floppy disk. Insert the floppy disk into the system you wish
to flash the BIOS. Then, boot the system to the floppy disk. The BIOS util-
ity will automatically flash the BIOS without any prompts. Please note that
this process may take a few minutes to complete. Do not be concerned if
the screen is paused for a few minutes.
When the BIOS flashing screen is completed, the system will reboot and
will show “Press F1 or F2”. At this point, you will need to load the BIOS
defaults. Press <F1> to go to the BIOS setup screen, and press <F9> to
load the default settings. Next, press <F10> to save and exit. The system
will then reboot.
Warning: Do not shut down or reset the system while updating the BIOS to prevent
possible system boot failure!
3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Troubleshooting
Important: The SPI BIOS chip installed on this motherboard is not re-
movable. To repair or replace a damaged BIOS chip, please send your
motherboard to RMA at Supermicro for service.
Question: I think my BIOS is corrupted. How can I recover my BIOS?
Answer: Please see Appendix C-BIOS Recovery for detailed instructions.
Question: Why do I get an error message “IASTOR.SYS read error” and "press F6
to install Intel RAID driver" when installing Windows on my motherboard?
Answer: To solve this issue, disable the IPMI jumper. Another solution is to use a
USB floppy drive instead of the onboard floppy drive. For the IPMI jumper location,
please check Chapter 1.
3-4 Battery Removal and Installation
Battery Removal
To remove the onboard battery, follow the steps below:
1. Power off your system and unplug your power cable.
2. Locate the onboard battery as shown below.
3. Using a tool such as a pen or a small screwdriver, push the battery lock out-
wards to unlock it. Once unlocked, the battery will pop out from the holder.
4. Remove the battery.
Battery
Battery
Lock
Proper Battery Disposal
Warning! Please handle used batteries carefully. Do not damage the battery in any
way; a damaged battery may release hazardous materials into the environment. Do
not discard a used battery in the garbage or a public landfill. Please comply with the
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
regulations set up by your local hazardous waste management agency to dispose of
your used battery properly.
Battery Installation
1. To install an onboard battery, follow the steps 1 & 2 above and continue
below:
2. Identify the battery's polarity. The positive (+) side should be facing up.
3. Insert the battery into the battery holder and push it down until you hear a
click to ensure that the battery is securely locked.
Warning: When replacing a battery, be sure to only replace it with the same type.
Battery Holder
1
2
Press down until
you hear a click.
This side up
3-5 Returning Merchandise for Service
A receipt or copy of your invoice marked with the date of purchase is required
before any warranty service will be rendered. You can obtain service by calling
your vendor for a Returned Merchandise Authorization (RMA) number. For faster
service, you may also obtain RMA authorizations online (http://www.supermicro.
com/support/rma/). When you return the motherboard to the manufacturer, the
RMA number should be prominently displayed on the outside of the shipping
carton, and mailed prepaid or hand-carried. Shipping and handling charges will
be applied for all orders that must be mailed when service is complete.
This warranty only covers normal consumer use and does not cover damages
incurred in shipping or from failure due to the alteration, misuse, abuse or improper
maintenance of products.
During the warranty period, contact your distributor first for any product prob-
lems.
3-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: AMI BIOS
Chapter 4
BIOS
4-1 Introduction
This chapter describes the AMI BIOS Setup Utility for the C7Z87-OCE. The ROM
BIOS is stored in a Flash EEPROM and can be easily updated. This chapter de-
scribes the basic navigation of the AMI BIOS Setup Utility setup screens.
Note: For AMI BIOS Recovery, please refer to the UEFI BIOS Recovery
Instructions in Appendix C.
Starting BIOS Setup Utility
To enter the AMI BIOS Setup Utility screens, press the <Delete> key while the
system is booting up.
Note: In most cases, the <Delete> key is used to invoke the AMI BIOS
setup screen. There are a few cases when other keys are used, such as
<F1>, <F2>, etc.
Each main BIOS menu option is described in this manual. The Main BIOS setup
menu screen has two main frames. The left frame displays all the options that can
be configured. Grayed-out options cannot be configured. Options in blue can be
configured by the user. The right frame displays the key legend. Above the key
legend is an area reserved for a text message. When an option is selected in the
left frame, it is highlighted in white. Often a text message will accompany it. (Note:
the AMI BIOS has default text messages built in. Supermicro retains the option to
include, omit, or change any of these text messages.)
The AMI BIOS Setup Utility uses a key-based navigation system called "hot keys".
Most of the AMI BIOS setup utility "hot keys" can be used at any time during the
setup navigation process. These keys include <F1>, <F4>, <Enter>, <ESC>, and
arrow keys, etc.
Note: Options printed in Bold are default settings.
How To Change the Configuration Data
The configuration data that determines the system parameters may be changed by
entering the AMI BIOS Setup utility. This Setup utility can be accessed by pressing
<Del> at the appropriate time during system boot.
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
How to Start the Setup Utility
Normally, the only visible Power-On Self-Test (POST) routine is the memory test.
As the memory is being tested, press the <Delete> key to enter the main menu of
the AMI BIOS Setup Utility. From the main menu, you can access the other setup
screens. An AMI BIOS identification string is displayed at the left bottom corner of
the screen, below the copyright message.
Warning! Do not upgrade the BIOS unless your system has a BIOS-related issue.
Flashing the wrong BIOS can cause irreparable damage to the system. In no event
shall Supermicro be liable for direct, indirect, special, incidental, or consequential dam-
ages arising from a BIOS update. If you have to update the BIOS, do not shut down
or reset the system while the BIOS is updating. This is to avoid possible boot failure.
4-2 Main Setup
When you first enter the AMI BIOS Setup Utility, you will enter the Main setup screen.
You can always return to the Main setup screen by selecting the Main tab on the
top of the screen. The Main BIOS Setup screen is shown below.
The following Main menu items will be displayed:
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Main Advanced Boot
Security Save & Exit
Set the Date. Use tab to
switch between Data elements.
System Date
System Time
[Wed05/16/2013]
[16:49:50]
Supermicro C7Z87-OCE
Version
Build Date
1.00
05/14/2013
Memory Information
Total Memory
4096 MB (DDR3)
:
Select Screen
Select Item
:
Enter: Select
+/-
F1 :
F2 :
F3 :
F4 :
:
Change Opt.
General Help
Previous Values
Optimized Defaults
Save & Exit
ESC :
Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
4-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: AMI BIOS
System Date/System Time
Use this option to change the system date and time. Highlight System Date or
System Time using the arrow keys. Enter new values using the keyboard. Press the
<Tab> key or the arrow keys to move between fields. The date must be entered in
Day MM/DD/YYYY format. The time is entered in HH:MM:SS format.
Note: The time is in the 24-hour format. For example, 5:30 P.M. appears
as 17:30:00.
The following BIOS items will also be displayed:
Supermicro C7Z87-OCE
Version
Build Date
Memory Information
Total Memory
This displays the total size of memory available in the system.
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
4-3 Advanced Setup Configurations
Use the arrow keys to select Advanced Setup and press <Enter> to access the
submenu items:
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Main
Advanced
Boot
Security
Save & Exit
System Boot Feature Setting
Boot Feature
CPU Configuration
Chipset Configuration
SATA Configuration
PCIe/PCI/PnP Configuration
ACPI Settings
Performance Tuning
PCH-FW Configuration
Intel(R) Thunderbolt
Super IO Configuration
H/W Monitor
:
Select Screen
Select Item
:
Enter: Select
+/-
F1 :
F2 :
F3 :
F4 :
:
Change Opt.
General Help
Previous Values
Optimized Defaults
Save & Exit
ESC :
Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Warning: Take Caution when changing the Advanced settings. An incorrect value,
a very high DRAM frequency or an incorrect DRAM timing setting may cause the
system to become unstable. When this occurs, restore the setting to the manufacture
default setting.
Boot Feature
Quiet Boot
Use this feature to select the screen display between POST messages or the OEM
logo at bootup. Select Disabled to display the POST messages. Select Enabled
to display the OEM logo instead of the normal POST messages. The options are
Enabled and Disabled.
AddOn ROM Display Mode
Use this feature to set the display mode for the Option ROM. Select Keep Cur-
rent to use the current AddOn ROM display setting. Select Force BIOS to use the
Option ROM display mode set by the system BIOS. The options are Force BIOS
and Keep Current.
Bootup Num-Lock
Use this feature to select the Power-on state for the Numlock key. The options
are Off and On.
4-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: AMI BIOS
Wait For 'F1' If Error
Select Enabled to force the system to wait until the 'F1' key is pressed if an error
occurs. The options are Disabled and Enabled.
Interrupt 19 Capture
Interrupt 19 is the software interrupt that handles the boot disk function. When this
item is set to Enabled, the BIOS ROM of the host adaptors will "capture" Interrupt 19
at bootup and allow the drives that are attached to these host adaptors to function
as bootable disks. If this item is set to Disabled, the BIOS ROM of the host adap-
tors will not capture Interrupt 19, and the drives attached to these adaptors will not
function as bootable devices. The options are Enabled and Disabled.
Re-try Boot
If this item is enabled, the BIOS will automatically reboot the system from a speci-
fied boot device after its initial boot failure. The options are Disabled, Legacy
Boot, and EFI Boot.
Power Configuration
Watch Dog Function
If enabled, the Watch Dog timer will allow the system to reboot when it is inactive
for more than 5 minutes. The options are Enabled and Disabled.
Power Button Function
This feature controls how the system shuts down when the power button is pressed.
Select 4 Seconds Override for the user to power off the system after pressing and
holding the power button for 4 seconds or longer. Select Instant Off to instantly
power off the system as soon as the user presses the power button. The options
are Instant Off and 4 Seconds Override.
Restore on AC Power Loss
Use this feature to set the power state after a power outage. Select Power-Off for
the system power to remain off after a power loss. Select Power-On for the system
power to be turned on after a power loss. Select Last State to allow the system to re-
sume its last power state before a power loss. The options are Stay-Off, Power-On,
and Last State.
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
CPU Configuration
The following CPU information will be displayed:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Type of CPU
CPU Signature
CPU Stepping
Microcode Patch
Max (Maximum) CPU Speed
Min (Minimum) CPU Speed
CPU Speed
Processor Cores
Intel HT(Hyper-Threading) Technology
Intel VT-x (Virtualization) Technology
Intel SMX (Trusted Execution) Technology
64-bit
EIST Technology
CPU C3 State
CPU C6 State
CPU C7 State
L1 Data Cache
L1 Code Cache
L2 Cache
L3 Cache
4-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: AMI BIOS
Clock Spread Spectrum
If this feature is set to Enabled, the BIOS will monitor the level of electromagnetic
interference caused by the components and will attempt to reduce the interference
whenever needed. The options are Enabled and Disabled.
Hyper-threading
Select Enabled to support Intel Hyper-threading Technology to enhance CPU per-
formance. The options are Enabled and Disabled.
Active Processor Cores
This feature determines how many CPU cores will be activated for each CPU. When
all is selected, all cores in the CPU will be activated. (Please refer to Intel's web
site for more information.) The options are All, 1, 2, and 3.
Limit CPUID Maximum
Select Enabled to set the maximum CPU ID value and to boot a legacy OS that
cannot support processors with extended CPUID functions. The options are Enabled
and Disabled (for the Windows OS).
Execute Disable Bit (Available if supported by the OS & the CPU)
Set to Enabled to enable the Execute Disable Bit to allow the processor to designate
areas in the system memory where an application code can execute and where it
cannot, thus preventing a worm or a virus from flooding illegal codes to overwhelm
the processor or damage the system during an attack. The default is Enabled.
(Refer to Intel and Microsoft Web Sites for more information.)
Intel® Virtualization Technology (Available when supported by the CPU)
Select Enabled to use the Intel Virtualization Technology to allow one platform to
run multiple operating systems and applications in independent partitions, creat-
ing multiple "virtual" systems in one physical computer. The options are Enabled
and Disabled.
Hardware Prefetcher (Available when supported by the CPU)
If set to Enabled, the hardware prefetcher will prefetch streams of data and instruc-
tions from the main memory to the L2 cache to improve CPU performance. The
options are Disabled and Enabled.
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
Adjacent Cache Line Prefetch (Available when supported by the CPU)
Select Enabled for the CPU to prefetch both cache lines for 128 bytes as comprised.
Select Disabled for the CPU to prefetch both cache lines for 64 bytes. The options
are Disabled and Enabled.
Note: If there is any change to this setting, you will need to power off and
reboot the system for the change to take effect. Please refer to Intel’s
web site for detailed information.
CPU AES
Select Enable for Intel CPU Advanced Encryption Standard (AES) Instructions sup-
port to enhance data integrity. The options are Enabled and Disabled.
EIST
EIST (Enhanced Intel SpeedStep Technology) allows the system to automatically
adjust processor voltage and core frequency in an effort to reduce power consump-
tion and heat dissipation. Please refer to Intel’s web site for detailed information.
The options are Disabled and Enabled.
Turbo Mode
This feature allows processor cores to run faster than the frequency recommended
by the manufacturer. The options are Disabled and Enabled. If this feature is set
to Enabled, the following items will display:
CPU Power Limit1
Use this feature to set the power limit for CPU1. Use the number keys on your
keyboard to enter the value. Enter 0 to use the manufacturer's default setting.
CPU Power Limit1 Time
This item allows the user to determine how long CPU1 should operate at the
power limit set by the user for the item above. Use the number keys on your
keyboard to enter the value. Enter 0 to use the manufacturer's default setting.
CPU Power Limit2
Use this feature to set the power limit for CPU2. Use the number keys on your
keyboard to enter the value. Enter 0 to use the manufacturer's default setting.
Platform Power Limit Lock
Use this feature to lock the power limit of the motherboard. The options are
Enabled and Disabled.
4-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: AMI BIOS
CPU Power Limit3
Use this feature to set the power limit for CPU3. Use the number keys on your
keyboard to enter the value. Enter 0 to use the manufacturer's default setting.
CPU Power Limit3 Time
This item allows the user to determine how long CPU3 should operate at the
power limit set by the user for the item above. Use the number keys on your
keyboard to enter the value. Enter 0 to use the manufacturer's default setting.
CPU Power Limit3 Duty Cycle
This item allows the user to determine the percentage of time CPU3 should
operate at the power set by the user for the item above (i.e., If Power Limit3
Time is set at 100 secs, a 60% duty cycle means CPU3 will run 60 seconds at
the power limit set in Power Limit3 every 100 seconds.). Use the number keys
on your keyboard to enter the value between 1~100. Enter 0 to use the manu-
facturer's default setting.
DDR Power Limit1
Use this feature to set the power limit for DDR Memory Module 1. Use the num-
ber keys on your keyboard to enter the value. Enter 0 to use the manufacture's
default setting.
DDR Power Limit1 Time
This item allows the user to determine how long Memory Module 1 should
operate at the power limit set by the item above. Use the number keys on your
keyboard to enter the value. Enter 0 to use the manufacturer's default setting.
DDR Power Limit2
Use this feature to set the power limit for Memory Module 2. Use the number
keys on your keyboard to enter the value. Enter 0 to use the manufacturer's
default setting.
1-Core Ratio Limit
This increases (multiplies) 1 clock speed in the CPU core in relation to the bus
speed when one CPU core is active. Press "+" or "-" on your keyboard to change
the value. Enter 0 to use the manufacturer's default setting.
2-Core Ratio Limit
This increases (multiplies) 2 clock speeds in the CPU core in relation to the bus
speed when two CPU cores are active. Press "+" or "-" on your keyboard to
change the value. Enter 0 to use the manufacturer's default setting.
4-9
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
3-Core Ratio Limit
This increases (multiplies) 3 clock speeds in the CPU core in relation to the bus
speed when three CPU cores are active. Press "+" or "-" on your keyboard to
change the value. Enter 0 to use the manufacturer's default setting.
4-Core Ratio Limit
This increases (multiplies) 4 clock speeds in the CPU core in relation to the bus
speed when four CPU cores are active. Press "+" or "-" on your keyboard to
change the value. Enter 0 to use the manufacturer's default setting.
Energy Performance
Use this feature to select an appropriate fan setting to achieve the maximum system
performance (with maximum cooling) or maximum energy efficiency (with maximum
power saving). The fan speeds are controlled by the firmware management. The
options are Performance, Balanced Performance, Balanced Energy, and Energy
Efficient.
VR Current Value
Use this feature to set the limit on the current voltage regulator (VR). Press "+" or
"-" on your keyboard to change this value. Enter 0 to use the manufacture default
setting.
CPU C States
C-States architecture, a processor power management platform developed by
Intel, can further reduce power consumption from the basic C1 (Halt State) state
that blocks clock cycles to the CPU. Select Enabled for CPU C Sates support. The
options are Enabled and Disabled. If this feature is set to Enabled, the following
items will display:
Enhanced C1 State (Available when "CPU C States" is set to Enabled)
Select Enabled to enable Enhanced C1 Power State to boost system perfor-
mance. The options are Enabled and Disabled.
CPU C3 Report (Available when "CPU C States" is set to Enabled)
Select Enabled to allow the BIOS to report the CPU C3 State (ACPI C2) to the
operating system. During the CPU C3 State, the CPU clock generator is turned
off. The options are Enabled and Disabled.
CPU C6 Report (Available when "CPU C States" is set to Enabled)
Select Enabled to allow the BIOS to report the CPU C6 State (ACPI C3) to the
operating system. During the CPU C6 State, the power to all caches is turned
off. The options are Enabled and Disabled.
4-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: AMI BIOS
C6 Latency (Available when "CPU C States" is set to Enabled)
Select Short to set a short delay time(period) during which the BIOS reports
CPU C6 State (ACPI C3) to the operating system. Select Long to set a long
delay time(period) during which the BIOS reports CPU C6 State (ACPI C3)
to the operating system. The options are Short and Long.
CPU C7 Report (Available when "CPU C States" is set to Enabled)
Select Enabled to allow the BIOS to report the CPU C7 State (ACPI C3) to the
operating system. CPU C7 State is a processor-specific low C-State. The options
are Disabled, CPU C7, and CPU C7s.
C7 Latency (Available when "CPU C States" is set to Enabled)
Select Short to set a short delay time(period) during which the BIOS reports
CPU C7 State (ACPI C3) to the operating system. Select Long to set a long
delay time(period) during which the BIOS reports CPU C7 State (ACPI C3)
to the operating system. The options are Short and Long.
C1 State Auto Demotion
When this item is enabled, the CPU will conditionally demote C3, C6 or C7
requests to C1 State based on un-cored auto-demote information. The options
are Disabled and Enabled.
C3 State Auto Demotion
When this item is enabled, the CPU will conditionally demote C6 or C7
requests to C3 State based on un-cored auto-demote information. The
options are Disabled and Enabled.
C State Pre-Wake
Select Enabled to support C State Pre-Wake State features. The options are
Enabled and Disabled
Package C-State limit
Select Auto for the AMI BIOS to automatically set the limit on the C-State package
register. The options are C0/C1, C2, C3, C6, C7, C7s and Auto.
LakeTiny Feature
Select Enabled for LakeTiny feature support for C-State configuration. The options
are Enabled and Disabled.
4-11
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
ACPI T State
Select Enabled to support Advanced Configuration and Power Interface (ACPI)
Throttling States (T State), which will lower the power consumption level for the
system as to the power consumption level set for CPU Performance State 1 to
achieve power efficiency. The options are Enabled and Disabled.
Chipset Configuration
WARNING: Setting the wrong values in the following sections may cause the system
to malfunction.
System Agent (SA) Configuration
The following System Agent (SA) information
•
•
System Agent Bridge Name
VT-d Capability
VT-d
Select Enabled to enable Intel Virtualization Technology support for Direct I/O VT-d
by reporting the I/O device assignments to the Virtual Machine Manager (VMM)
through the DMAR ACPI Tables. This feature offers fully-protected I/O resource-
sharing across the Intel platforms, providing the user with greater reliability, security
and availability in networking and data-sharing. The settings are Enabled and
Disabled.
Graphics Configuration
This item displays the following graphics information:
Graphics Configuration
•
•
IGFX VBIOS Version
IGfx Frequency
Graphics Turbo IMON Current
Use this feature to set the limit on the current voltage regulator. Press "+" or "-"
on your keyboard to change this value.
4-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: AMI BIOS
Primary Display
Use this feature to select the graphics device to be used as the primary display. You
can select from a device installed on the CPU IGFX, CPU SLOT, or PCH SLOT.
The options are Auto, CPU IGFX, CPU SLOT, and PCH SLOT.
CPU Slot (Available when Primary Display is set to Auto)
Use this item to select the graphics device installed in an expansion slot sup-
ported by the CPU to be used as the primary display. The options are Auto,
CPU SLOT4 PCI-E 3.0 X8 (IN X16) and CPU SLOT2 PCI-E 3.0 X4 (IN X16).
PCH Slot (Available when Primary Display is set to Auto)
Use this item to select the graphics device installed in an expansion slot sup-
ported by the PCH to be used as the primary display. The options are Auto, and
PCH_SLOT1/SLOT3/SLOT5 PCI-E 2.0 X1 (IN X4).
CPU IGFX
Select Auto to keep an internal graphics device installed on an expansion slot sup-
ported by the CPU to be automatically enabled. The options are Auto, Disabled,
and Enabled.
GTT Size
Use this feature to set the memory size to be used by the graphics translation table
(GTT). The options are 1MB and 2MB.
Aperture Size
Use this feature to set the Aperture size, which is the size of system memory re-
served by the BIOS for graphics device use. The options are 128MB, 256MB and
512 MB.
DVMT Pre-Allocated
Dynamic Video Memory Technology (DVMT) allows dynamic allocation of system
memory to be used for video devices to ensure best use of available system
memory based on the DVMT 5.0 platform. The options are 32M, 64M, 96M, 128M,
160M, 192M, 224M, 256M, 288M, 320M, 352M, 384M, 416M, 448M, 480M, 512M,
and 1024M.
DVMT (Dynamic Video Memory Technology) Total Gfx Mem
Use this feature to set the total memory size to be used by internal graphics de-
vices based on the DVMT 5.0 platform. The options are 128MB, 256MB and MAX.
4-13
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
Gfx (Graphics) Low Power Mode
Select Enabled to use the low power mode for internal graphics devices installed
in a small form factor (SFF) computer. The options are Enabled and Disabled.
PCI-E Configuration
This item displays the information of the (graphics) device installed on a PCI-E
slot.
CPU SLOT6 PCI-E 3.0 X16
CPU SLOT6 PCI-E 3.0 X16 - Gen X
This feature allows the user to select PCI-E support for the device installed on
Slot6. The options are Auto, Gen1 (Generation 1), Gen 2 and Gen 3.
CPU SLOT4 PCI-E 3.0 X8(IN X16)
CPU SLOT4 PCI-E 3.0 X8(IN X16) - Gen X
This feature allows the user to select PCI-E support for the device installed on
Slot4. The options are Auto, Gen1 (Generation 1), Gen 2 and Gen 3.
CPU SLOT2 PCI-E 3.0 X4 (IN X16)
CPU SLOT2 PCI-E 3.0 X4 (IN X16) - Gen X
This feature allows the user to select PCI-E support for the device installed on
Slot4. The options are Auto, Gen1 (Generation 1), Gen 2 and Gen 3.
Detect Non-Compliant Device
Select Enabled for the AMI BIOS to automatically detect a PCI-E device that is
not compliant with the PCI-E standards. The options are Enabled and Disabled.
Program PCI-E ASPM After OpROM
PCI-E ASPM, the Active State Power Management for PCI-Express slots, is a
power management protocol used to manage power consumption of serial-link
devices installed on PCI-Exp slots during a prolonged off-peak time. If this item
is set to Enabled, PCI-E ASMP will be programmed after OpROM. If this item
is set to Disabled, the PCI-E ASPM will be programmed before OpROM. The
options are Enabled and Disabled.
4-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: AMI BIOS
CPU SLOT6 PCI-E 3.0 X16 - ASPM,
CPU SLOT4 PCI-E 3.0 X8(IN X16) - ASPM,
CPU SLOT2 PCI-E 3.0 X4 (IN X16)- ASPM
Use this feature to set the ASPM (Active State Power Management) level for
the graphics device installed on a PCI-E or PCI slot specified by the user. The
options are Disabled, ASPM L0s, ASPM L1, ASPM L0sL1, and Auto.
DMI Link ASPM Control
Use this feature to set the ASPM (Active State Power Management) state on
the SA (System Agent) side of the DMI Link. The options are Disabled, L0s,
L1 and L0sL1.
PCH DMI Link ASPM Control
Use this feature to set the ASPM (Active State Power Management) state on
the device installed on the DMI Link supported by the PCH chip. The options
are Disabled and Enabled.
PCH SLOT1 / SLOT3 / SLOT5 PCI-E 2.0 X1 ASPM
This feature sets the ASPM (Active State Power Management) level for the de-
vices installed on PCI SLOT1, SLOT3 and SLOT5 . The options are Disabled,
L0s, L1, L0sL1 and Auto.
Memory Configuration
This item displays the following information on the memory modules installed
on the motherboard.
•
•
•
•
•
•
•
•
•
Memory RC Version
Memory Frequency
Total Memory
Memory Voltage
DIMM A1
DIMM A2
DIMM B1
DIMM B2
CAS Latency (tCL)
4-15
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
Minimum Delay Time
•
•
•
•
CAS to RAS (tRCDmin)
Row Precharge (tRPmin)
Active to Precharege (tRASmin)
Max TOLUD (Top of Low Usable DRAM)
This feature sets the maximum TOLUD value, which specifies the "Top of Low
Usable DRAM" memory space to be used by internal graphics devices, GTT
Stolen Memory, and TSEG, respectively, if these devices are enabled. The op-
tions are Dynamic, 1 GB, 1.25 GB, 1.5 GB, 1.75 GB, 2 GB, 2.25 GB, 2.5 GB,
2.75 GB, 3 GB and 3.25 GB.
Note: TSEG is a block of memory that is only accessible by the processor
while operating in System Management Mode (SMM).
Memory Scrambler
This feature enables or disables memory scrambler support for memory error
correction. The settings are Enabled and Disabled.
PCH-IO Configuration
This item displays the information for the PCH-IO Chip.
•
•
•
Intel PCH Rev ID
USB Configuration
USB Devices: 1 Keyboard, 1 Mouse, 2 Hubs
EHCI1
Select Enabled to enable EHCI (Enhanced Host Controller Interface) Controller 1
for USB 2.0 support. One EHCI controller must always be enabled. The settings
are Enabled and Disabled.
EHCI2
Select Enabled to enable EHCI (Enhanced Host Controller Interface) Controller 2
for USB 2.0 support. One EHCI controller must always be enabled. The settings
are Enabled and Disabled.
4-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: AMI BIOS
Legacy USB Support
Select Enabled to support legacy USB devices. Select Auto to disable legacy
support when legacy USB devices are not present. If Disable is selected, legacy
USB devices will not be supported. The options are Enabled, Disabled and Auto.
Port 60/64 Emulation
This feature enables or disables I/O port 60h/64h emulation support. This should
be enabled for complete USB keyboard legacy support for non-USB-aware op-
erating systems. The options are Disabled and Enabled.
XHCI Hand-Off
This item is a work-around solution for operating systems that do not support
XHCI (Extensible Host Controller Interface) hand-off. The XHCI ownership
change should be claimed by the XHCI driver. The settings are Enabled and
Disabled.
EHCI Hand-Off
This item is for Operating Systems that do not support Enhanced Host Controller
Interface (EHCI) hand-off. When this item is enabled, EHCI ownership change
will be claimed by the EHCI driver. The settings are Enabled and Disabled.
XHCI Mode
This feature handles the operation mode for the XHCI (Extensible Host Control-
ler Interface) controller. The settings are Smart Auto, Auto, Enabled, Disabled
and Manual.
Frontside Audio Mode
This feature selects the type of audio output for the front_side audio header or
connection. Select HD Audio for High Definition; otherwise, select AC '97 for
legacy audio. The options are HD Audio and AC' 97.
On Board Chip Configuration
This item displays the On Board Chip options.
ASMedia 1061 SATA Controller
ASMedia 1061 SATA Controller
Select Enabled to activate the onboard ASMedia SATA controller. The settings
are Enabled and Disabled.
4-17
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
SATA Configuration
When this submenu is selected, the AMI BIOS automatically detects the presence
of the SATA Devices and displays the following items:
SATA Controllers
This item Enables or Disables the built-in SATA controllers on the motherboard.
The options are Enabled and Disabled.
SATA Mode Selection
This item selects the mode for the installed SATA drives. The options are IDE,
AHCI and RAID.
SATA RAID Option ROM/UEFI Driver (Available if the item above - SATA
Mode Select is set to AHCI or RAID)
Select Enabled to use the SATA RAID Option ROM/UEFI driver for system boot.
The options are Enabled and Disabled.
If the item above -SATA Mode Select is set to AHCI, the following items are
displayed:
Serial ATA Port 0~ Port 5
This item displays the information detected on the installed SATA drives on the
particular SATA port.
•
•
Model number of drive and capacity
Software Preserve Support
Port 0 ~ Port 5 Hot Plug
This feature designates the port specified for hot plugging. Set this item to En-
abled for hot-plugging support, which will allow the user to replace a SATA disk
drive without shutting down the system. The options are Enabled and Disabled.
Port 0 ~ Port 1 SATA Device Type
This feature configures the selected SATA port to support either a solid state
drive or hard disk drive. The options are Hard Disk Drive and Solid Sate Drive.
Port 0 ~ Port 5 Spin Up Device
On an edge detect from 0 to 1, set this item to allow the PCH to start a COMRE-
SET initialization sequence to the device. The options are Enabled and Disabled.
4-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: AMI BIOS
If the item above - SATA Mode Select is set to IDE, the following items are
displayed:
Serial ATA Port 0~ Port 5
This item displays the information detected on the installed SATA drives on the
particular SATA port.
•
•
Model number of drive and capacity
Software Preserve Support
If the item above - SATA Mode Select is set to RAID, the following items are
displayed:
Serial ATA Port 0~ Port 5
This item displays the information detected on the installed SATA drives on the
particular SATA port.
•
•
Model number of drive and capacity
Software Preserve Support
Port 0 ~ Port 5 Hot Plug
This feature designates this port for hot plugging. Set this item to Enabled for
hot-plugging support, which will allow the user to replace a SATA drive without
shutting down the system. The options are Enabled and Disabled.
Port 0 ~ Port 1 SATA Device Type
This feature configures the selected SATA port to support either a solid state
drive or hard disk drive. Set this item to Enabled to enable hot-plugging. The
options are Hard Disk Drive and Solid Sate Drive.
Port 0 ~ Port 5 Spin Up Device
On an edge detect from 0 to 1, set this item to allow the PCH to start a COMRE-
SET initialization sequence to the device. The options are Enabled and Disabled.
PCIe/PCI/PnP Configuration
This feature allows the user to set the PCI/PnP configurations for the following items:
Above 4G Decoding
Select Enabled for 64-bit devices to be decoded above the 4GB address space
If 64bit PCI decoding is supported by the system. The options are Disabled and
Enabled.
4-19
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
VGA Palette Snoop
Select Enabled to support VGA palette register snooping which will allow the
PCI cards that do not contain their own VGA color palette to examine the video
cards palette and mimic it for proper color display. The options are Disabled and
Enabled.
PERR# Generation
Select Enabled to allow a PCI device to generate a PERR number for a PCI Bus
Signal Error Event. The options are Enabled and Disabled.
SERR# Generation
Select Enabled to allow a PCI device to generate an SERR number for a PCI Bus
Signal Error Event. The options are Enabled and Disabled.
PCH SLOT1 PCI-E 2.0 X1 (IN X4),
CPU SLOT2 PCI-E 3.0 X4 (IN X16),
PCH SLOT3 PCI-E 2.0 X1 (IN X4),
CPU SLOT4 PCI-E 3.0 X8 (IN X16),
PCH SLOT5 PCI-E 2.0 X1 (IN X4),
CPU SLOT6 PCI-E 3.0 X16
Select Disabled to deactivate the selected slot, Legacy to activate the slot in legacy
mode and EFI to activate the slot in EFI mode. The options are Disabled, Legacy
and EFI.
Launch Storage OPROM Policy
This feature controls how the system executes UEFI (Unified Extensible Firmware
Interface), and legacy storage OPROM. Select Legacy Only to boot the system using
a legacy device installed in a PCI slot. The options are UEFI Only and Legacy Only.
Other PCI Device ROM Priority
This feature selects a PCI device Option ROM for system boot if this device is not
a network, mass storage, or video device. The options are UEFI Only and Legacy
Only.
Onboard LAN1 Option ROM/Onboard LAN2 Option ROM
Select PXE (Preboot Execution Environment) to boot the computer using a PXE
device installed in a LAN port specified. Select Disabled to prevent system boot
using a device installed in a LAN port. The options for Onboard LAN1 Option ROM/
Onboard LAN2 Option ROM are Disabled and PXE. The default for Onboard LAN1
Option ROM is PXE, and Disabled for Onboard LAN2 Option ROM.
4-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: AMI BIOS
Network Stack
Select Enabled to enable PXE (Preboot Execution Environment) or UEFI (Unified
Extensible Firmware Interface) for network stack support. The options are Enabled
and Disabled.
Ipv4 PXE Support (Available when Network Stack is set to Enabled)
Select Enabled to enable Ipv4 PXE (Preboot Execution Environment) for boot
support. If this feature is set to Disabled, Ipv4 PXE boot option will not be
supported. The options are Enabled and Disabled.
Ipv6 PXE Support (Available when Network Stack is set to Enabled)
Select Enabled to enable Ipv6 PXE (Preboot Execution Environment) for boot
support. If this feature is set to Disabled, Ipv6 PXE boot option will not be
supported. The options are Enabled and Disabled.
ACPI Settings
High Precision Timer
Select Enabled to activate the High Performance Event Timer (HPET) that produces
periodic interrupts at a much higher frequency than a Real-time Clock (RTC) does in
synchronizing multimedia streams, providing smooth playback and reducing the de-
pendency on other timestamp calculation devices, such as an x86 RDTSC Instruc-
tion embedded in the CPU. The High Performance Event Timer is used to replace
the 8254 Programmable Interval Timer. The options are Enabled and Disabled.
ACPI Sleep State
This feature selects the ACPI Sleep State that the system will enter into when the
suspend button is activated. The options are Suspend Disabled, S1 only (CPU Stop
Clock), S3 only (Suspend to RAM), and Both S1 and S3.
Trusted Computing (Available when a TPM Device is
Detected)
Configuration
Security Device Support
Select Enable for the AMI BIOS to automatically download the drivers needed
to provide Trusted Computing platform support for this machine to ensure date
integrity and network security. The options are Disable and Enable.
4-21
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
TPM State
Select Enabled to use TPM (Trusted Platform Module) settings for system data
security. The options are Disabled and Enabled.
Note: The system will reboot for the change on TPM State to take effect.
Pending Operation
Use this item to schedule a TPM-related operation to be performed by a security
device for TPM support. The options are None, Enable Take Ownership, Disable
Take Ownership, and TPM Clear.
Note: The computer will reboot to carry out a pending TPM operation and
change TPM state for a TPM device.
Current Status Information
This feature indicates the status of the following TPM items:
TPM Enabled Status
TPM Active Status
TPM Owner Status
Intel TXT (LT) Support
Intel TXT (Trusted Execution Technology) helps protect against software-based
attacks to ensure the security, confidentiality, and integrity of all data stored in the
system. The options are Enabled and Disabled.
Performance Tuning Mode (Available when both XMP
memory and an Extreme Edition CPU are installed)
This item allows the user to choose the Intel Extreme Memory Profile (XMP) Speci-
fication which enables DDR3 memory to operate beyond the standard JEDEC SPD
specification. Select XMP for 1600 MHz XMP memory operation for better system
performance.
CPU Configuration
The following CPU Configuration submenu items will display:
Non Turbo Ratio Override
This feature allows the user to set the non-turbo override ratio. The default set-
ting is dependent on the type of CPU installed.
4-22
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: AMI BIOS
Package Current Lock
Select Enabled to lock the current CPU package values. The options are Enabled
and Disabled.
IA Core Current Max (1/8 Amp)
This feature allows the user to set the maximum electric current value for the
Intel CPU cores. The default setting is 760.
Enhanced Intel SpeedStep Technology
Select Enabled to enable Enhanced Intel SpeedStep Technology (EIST) support
to allow the system to automatically adjust processor voltage and core frequency
to enhance power efficiency. The options are Disabled and Enabled.
Turbo Mode
Select Enabled to use Turbo Mode to boost system performance. The options
are Disabled and Enabled. The following options are available if Turbo Mode
is enabled:
Package TDP Lock Enable
Select Enabled to lock the Thermal Design Power (TDP) value for the pro-
cessor. The options are Disabled and Enabled.
Power Limit 1 Value (Watt)
Use this feature to set the power limit for CPU1. Use the number keys on
your keyboard to enter the value. The default setting is 84.
Power Limit 1 Time (Seconds)
This item allows the user to determine how long CPU1 should operate at
the power limit set by the user for the item above. Use the number keys on
your keyboard to enter the value. The default setting is 8.
Power Limit 2 Switch
Select Enabled for power limit switch for CPU2. The settings are Disabled
and Enabled.
Power Limit 2 Value (Watt)
Use this feature to set the power limit for CPU2. Use the number keys on
your keyboard to enter the value. The default setting is 105.
1 Core Ratio Limit
This increases (multiplies) 1 clock speed in the CPU core in relation to the
bus speed when one CPU core is active. Use the number keys on your
4-23
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
keyboard to enter the value. The default setting is dependent on the CPU
installed.
2 Core Ratio Limit
This increases (multiplies) 2 clock speeds in the CPU core in relation to
the bus speed when two CPU cores are active. Use the number keys on
your keyboard to enter the value. The default setting is dependent on the
CPU installed.
3 Core Ratio Limit
This increases (multiplies) 3 clock speeds in the CPU core in relation to
the bus speed when three CPU cores are active. Use the number keys on
your keyboard to enter the value. The default setting is dependent on the
CPU installed.
4 Core Ratio Limit
This increases (multiplies) 4 clock speeds in the CPU core in relation to
the bus speed when four CPU cores are active. Use the number keys on
your keyboard to enter the value. The default setting is dependent on the
CPU installed.
Disable OverClocking Lock
If this feature is set to Enabled, the OverClocking Lock will be deactivated. The
options are Disabled and Enabled.
Filter PLL
This feature selects the Phase Lock Loop (PLL) filter frequency. The options are
High Frequnecy 3.2GHz and Lower Frequnecy 1.6GHz.
ICC (Intelligent Clock Control) Clock Setting
Host Clock Override (1/100 MHz)
Use this item to set the CPU clock override value for the host system. Press
"+" or "-" on your keyboard to change the value. The default setting is 10000.
4-24
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: AMI BIOS
North Bridge Configuration
The following North Bridge Configuration submenu items will display:
Memory Multiplier Configuration
Performance Memory Profiles
Use this feature to set Performance Memory Profiles which may cause impact
on memory behavior due to different sizes of memory used in the system. Select
Automatic to allow the BIOS to automatically set Performance Memory Profiles.
Select Manual to manually configure Performance Profiles. The options are
Automatic, Manual, XMP Profile 1 and XMP Profile 2.
XMP Profile 1
XMP Profile 2
If Manual is selected, the following options will be displayed:
Memory Timing Configuration
Memory Clock Multiplier
This option selects the Memory Clock Multiplier. The options are
1.33 and 1.00.
Memory Multiplier
This option selects the Memory Multiplier value. The options are
8, 10, 12, 14, 16, 18, 20, 22, 24, 26 and 28.
tCL
This option configures the Cas Latency Range. Enter a number
between 4-18. The default is 9.
tRP
This option selects the Ras Precharge Range. Enter a number
between 1-38. The default is 11.
tRCD
This option configures the Row to Col Delay Range. Enter a
number between 1-38. The default is 11.
tRAS
This option selects the Ras Active Time. Enter a number between
1-586. The default is 28.
4-25
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
tWR
This option configures the Minimum Write Recovery Time. Enter
a number between 1-38. The default is 12.
tRFC
This option selects the Minimum Refresh Recovery Delay Time.
Enter a number between 1-9363. The default is 128.
tWTR
This option configures the Minimum Internal Write to Read Com-
mand Delay Time. Enter a number between 1-38. The default is 6.
tRRD
This option selects the Minimum Row Active To Row Active Delay
Time. Enter a number between 1-38. The default is 5.
tRTP
This option configures the Internal Read to Precharge Command
Delay Time. Enter a number between 1-38. The default is 6.
tCWL Value
This option selects the Minimum CAS Write Latency Time. Enter
a numeric value. The default is 8.
tREFI Value
This option configures the Maximum tREFI Time (Average Periodic
Refrech Interval). Enter a numeric value. The default is 6240.
tFAW
This option selects the Minimum Four Activate Window Delay
Time. Enter a numeric value between 1-586. The default is 24.
tRC
This option configures the Minimum Active to Active/Refresh De-
lay Time (tRCmin). Enter a numeric value between 1-586. The
default is 39.
4-26
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: AMI BIOS
Memory Voltage
Use this feature to select the Memory Voltage. The options are 1.35V,
1.40V, 1.45V, 1.50V, 1.55V, 1.60V, 1.65V, 1.70V, 1.75V, 1.80V, 1.85V,
1.90V, 1.95V and Auto.
Intel Graphics Configuration
Graphics Core Ratio Limit
Use this feature to set graphics core ratio limit. The default setting is dependent
on the type of CPU installed.
Overclocking CPU Option
The following Overclocking CPU Option submenu items will display:
CPU Adaptive Voltage Target (mV)
Use this feature to set the CPU voltage Target(mV) value from 0mV to 2000mV.
Enter 0 to use the manufacture default value.
CPU Voltage Mode
Use this feature to select the CPU voltage mode. The options are Override and
Adaptive.
CPU Voltage Offset (mV)
Use this feature to set to set the CPU Voltage Offset value from -1000mV to
998mV. Enter 0 to use the manufacture default value.
Offset Prefix
Use this feature to set the Offset value as a positive (+) number or a nega-
tive (-) number. Press "+" or "-" on your keyboard to make a selection.
The default setting is "+".
Overclocking RING Option
The following Overclocking RING Option submenu items will display:
RING Adaptive Voltage Target (mV)
Use this feature to set the RING Adaptive Voltage Target(mV) value from 0mV
to 2000mV. Enter 0 to use the manufacture default value.
RING Voltage Mode
Use this feature to select the CPU RING Voltage mode. The options are Over-
ride and Adaptive.
4-27
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
RING Voltage Offset (mV)
Use this feature to set to set the RING Voltage Offset value from -1000mV to
998mV. Enter 0 to use the manufacture default value.
Offset Prefix
Use this feature to set the Offset value as a positive (+) number or a nega-
tive (-) number. Press "+" or "-" on your keyboard to make a selection. The
default setting is "+".
Overclocking SVID and FIVR Option
The following Overclocking SVID and FIVR Option submenu items will display:
SVID Control Enable
Select Enabled to enable SVID control for Intel SVID Protocol support. If this
setting is set to Disabled, there will be no change made to SVID until the CPU
powers down. The options are Enabled and Disabled.
SVID Override Voltage Target (mV)
Use this feature to set the value for SVID Override Voltage Target (up to 2500
mV). Enter 0 to use the manufacture default value.
FIVR Faults Enable
Select Enabled to enable FIVR Faults support. If this setting is set to Disabled,
there will be no change made to FIVR Faults settings until the CPU powers
down. The options are Enabled and Disabled.
FIVR Efficiency Enable
Select Enabled to enable FIVR Efficiency support. If this setting is set to Disabled,
there will be no change made to FIVR Efficiency status until the CPU powers
down. The options are Enabled and Disabled.
Overclocking GT Option
The following Overclocking GT Option submenu items will display:
GT Adaptive Voltage Target (mV)
Use this feature to set the GT Adaptive voltage Target(mV) value from 0mV to
2000mV. Enter 0 to use the manufacture default value.
GT Voltage Mode
Use this feature to select the Overclocking GT mode. The options are Override
and Adaptive.
4-28
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: AMI BIOS
GT Voltage Offset (mV)
Use this feature to set the GT Voltage Offset value between -1000mV and
998mV. Enter 0 to use the default setting.
Offset Prefix
Use this feature to set the GT Voltage Offset value as a positive (+) number
or a negative (-) number. Press "+" or "-" on your keyboard to make a selec-
tion. The default setting is "+".
Overclocking UNCORE Option
The following Overclocking UNCORE Option submenu items will display:
UNCORE Voltage Offset (mV)
Use this feature to set the UNCORE Voltage Offset value between -1000mV and
998mV. Enter 0 to use the default setting.
Offset Prefix
Use this feature to set the Offset value as a positive (+) number or a nega-
tive (-) number. Press "+" or "-" on your keyboard to make a selection. The
default setting is "+".
Overclocking IOA and IOD Option
The following Overclocking IOA and IOD Option submenu items will display:
IOA Voltage Offset (mV)
Use this feature to set the IOA Voltage Offset value between -1000mV and
998mV. Enter 0 to use the default setting.
Offset Prefix
Use this feature to set the Offset value as a positive (+) number or a nega-
tive (-) number. Press "+" or "-" on your keyboard to make a selection. The
default setting is "+".
IOD Voltage Offset (mV)
Use this feature to set the IOD Voltage Offset value between -1000mV and
998mV. Enter 0 to use the default setting.
4-29
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
Offset Prefix
Use this feature to set the Offset value as a positive (+) number or a nega-
tive (-) number. Press "+" or "-" on your keyboard to make a selection. The
default setting is "+".
Overclocking Button Option
The following Overclocking Button Option submenu items will display. These
are the settings for the OC buttons on the motherboard:
OC1 Button Setting Configuration,
OC2 Button Setting Configuration
The following settings are displayed with their current values, please enter
numeric characters only:
IA Core Current Max (1/8)
Power Limit 1 Value (Watts)
Power Limit 2 Value (Watts)
1 Core Ratio Limit
2 Core Ratio Limit
3 Core Ratio Limit
4 Core Ratio Limit
OC3 Button Setting Configuration
ICC Clock Setting
Host Clock Override (1/100 MHz)
This option allows the user to change the current Host Clock Override value.
Please enter numeric characters only.
CPU Voltage Offset (mV)
Use this feature to set to set the CPU Voltage Offset value from -1000mV
to 998mV. Enter 0 to use the manufacture default value.
Offset Prefix
Use this feature to set the Offset value as a positive (+) number or
a negative (-) number. Press "+" or "-" on your keyboard to make a
selection. The default setting is "+".
4-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: AMI BIOS
RING Voltage Offset (mV)
Use this feature to set to set the RING Voltage Offset value from -1000mV
to 998mV. Enter 0 to use the manufacture default value.
Offset Prefix
Use this feature to set the Offset value as a positive (+) number or
a negative (-) number. Press "+" or "-" on your keyboard to make a
selection. The default setting is "+".
IOA Voltage Offset (mV)
Use this feature to set the IOA Voltage Offset value between -1000mV and
998mV. Enter 0 to use the default setting.
Offset Prefix
Use this feature to set the Offset value as a positive (+) number or
a negative (-) number. Press "+" or "-" on your keyboard to make a
selection. The default setting is "+".
IOD Voltage Offset (mV)
Use this feature to set the IOD Voltage Offset value between -1000mV and
998mV. Enter 0 to use the default setting.
Offset Prefix
Use this feature to set the Offset value as a positive (+) number or
a negative (-) number. Press "+" or "-" on your keyboard to make a
selection. The default setting is "+".
SVID Override Voltage Target (mV)
Use this feature to set the value for SVID Override Voltage Target (up to
2500 mV). Enter 0 to use the manufacture default value.
Memory Multiplier Configuration
Performance Memory Profiles
This option selects the Performance Memory Profiles which impacts memory
sizing behavior. The options are Automatic, Manual, XMP Profile 1, and
XMP Profile 2. If Manual is selected, the following options are displayed:
4-31
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
Memory Timing Configuration
Memory Clock Multiplier
This option selects the Memory Clock Multiplier. The options are
1.33 and 1.00.
Memory Multiplier
This option selects the Memory Multiplier value. The options are
8, 10, 12, 14, 16, 18, 20, 22, 24, 26 and 28.
tCL
This option configures the Cas Latency Range. Enter a number
between 4-18. The default is 9.
tRP
This option selects the Ras Precharge Range. Enter a number
between 1-38. The default is 11.
tRCD
This option configures the Row to Col Delay Range. Enter a
number between 1-38. The default is 11.
tRAS
This option selects the Ras Active Time. Enter a number between
1-586. The default is 28.
tWR
This option configures the Minimum Write Recovery Time. Enter
a number between 1-38. The default is 12.
tRFC
This option selects the Minimum Refresh Recovery Delay Time.
Enter a number between 1-9363. The default is 128.
tWTR
This option configures the Minimum Internal Write to Read Com-
mand Delay Time. Enter a number between 1-38. The default is 6.
4-32
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: AMI BIOS
tRRD
This option selects the Minimum Row Active To Row Active Delay
Time. Enter a number between 1-38. The default is 5.
tRTP
This option configures the Internal Read to Precharge Command
Delay Time. Enter a number between 1-38. The default is 6.
tCWL Value
This option selects the Minimum CAS Write Latency Time. Enter
a numeric value. The default is 8.
tREFI Value
This option configures the Maximum tREFI Time (Average Periodic
Refrech Interval). Enter a numeric value. The default is 6240.
tFAW
This option selects the Minimum Four Activate Window Delay
Time. Enter a numeric value between 1-586. The default is 24.
tRC
This option configures the Minimum Active to Active/Refresh De-
lay Time (tRCmin). Enter a numeric value between 1-586. The
default is 39.
Memory Voltage
Use this feature to select the Memory Voltage. The options are 1.35V,
1.40V, 1.45V, 1.50V, 1.55V, 1.60V, 1.65V, 1.70V, 1.75V, 1.80V, 1.85V,
1.90V, 1.95V and Auto.
UNCORE Voltage Offset (mV)
Use this feature to set the UNCORE Voltage Offset value between
-1000mV and 998mV. Enter 0 to use the default setting.
Offset Prefix
Use this feature to set the Offset value as a positive (+) number or
a negative (-) number. Press "+" or "-" on your keyboard to make a
selection. The default setting is "+".
4-33
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
Intel Graphics Configuration
Graphics Core Ratio Limit
This option allows the configuration of the Graphics Core Ratio limit. Please
enter a numeric value. The default is 24.
Case LED
The following setting will enable the LED lamp that is mounted on the chas-
sis to flash when Over-Clocking is enabled. The options are Enabled and
Disabled.
PCH-FW Configuration
The following information are displayed:
•
•
•
•
•
ME FW Version
ME Firmware Mode
ME Firmware Type
ME Firmware SKU
PTT Capability/State
Firmware Update Configuration
ME FW Image Re-Flash
Select Enabled to re-flash the ME (Management Engine) Firmware. The options
are Disabled and Enabled.
Intel(R) Thunderbolt
The following Intel Thunderbolt submenu items will display:
•
•
•
Thunderbolt Specification Version
Intel Sample Code Version
Thunderbolt Host Chip
4-34
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: AMI BIOS
Security Level
This option selects the security level for the Intel Thunderbolt port(s) . The options
are Legacy Mode, Unique ID, One Time Saved Key, and DP+++ only.
Wake From Thunderbolt Devices
This option enables the wake-up feature from Thunderbolt devices. The options
are Disabled, and Enabled.
Thunderbolt PCIe Cache-Line Size
This option configures the cache-line size value to be configured on the Thunderbolt
PCIe subtree. The options 0, 1, 2, 4, 8, 16, 32, 64, and 128.
Thunderbolt Surprise-Removal
This option enables or disables the Thunderbolt Surprise Removal workaround
support. The options are Disabled and Enabled.
Thunderbolt Software SMI Delay
This option configures the Thunderbolt Software SMI Delay. Enter a numeric value
in milliseconds. Default is 20ms. (Note: 0 = Disabled).
Reserved Memory per Physical Slot
This option configures the Thunderbolt reserved memory for each physical slot. For
example, if a PCIe device uses <X MB of memory, the BIOS will reserve X MB per
physical slot. Enter a numeric value in megabytes. Default is 32MB.
Reserved Prefetch Memory per Physical Slot
This option configures the Thunderbolt reserved Prefetch memory for each physi-
cal slot. For example, if a PCIe device uses <X MB of prefetchable memory, the
BIOS will reserve X MB per physical slot. Enter a numeric value in megabytes.
Default is 32MB.
Thunderbolt Device IO Resource Support
This option enables or disables the IO resource for the Thunderbolt device. The
options are Disabled and Enabled.
Super IO Configuration
Super IO Chip NCT6776D
Serial Port 1 Configuration
Select Enabled to enable onboard serial ports. The options are Enabled
and Disabled.
4-35
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
Device Settings
This feature displays the base I/O port address and the Interrupt Request
address of Serial Port 1.
Change Port 1 Settings
This option specifies the base I/O port address and the Interrupt Request
address of Serial Port 1. Select Auto to let the BIOS automatically assign
the base I/O and IRQ address.
The options for Serial Port 1 are Auto, (IO=3F8h; IRQ=4), (IO=3F8h;
IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12), (IO=2F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11,
12), (IO=3E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12) and (IO=2E8h; IRQ=3,
4, 5, 6, 7, 9, 10, 11, 12).
4-36
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: AMI BIOS
H/W (Hardware) Monitor
PC Health Status
Fan Speed Control Mode
This feature allows the user to decide how the system controls the speeds of the
onboard fans. The CPU temperature and the fan speed are correlative. When the
CPU on-die temperature increases, the fan speed will also increase for effective
system cooling. Select "Full Speed" to allow the onboard fans to run at full speed
(of 100% Pulse Width Modulation Duty Cycle) for maximum cooling. This setting
is recommended for special system configuration or debugging. Select "Standard"
for the onboard fans to run at 50% of the Initial PWM Cycle in order to balance the
needs between system cooling and power saving. This setting is recommended for
regular systems with normal hardware configurations. The options are Full Speed
(@100% of PWM Cycle), and Standard (@50% of PWM Cycle).
The following items will be displayed:
•
•
•
CPU Temperature (PECI)
System Temperature
Peripheral Temperature
•
•
•
•
•
•
•
•
•
•
•
PCH Temperature
Fan 1 Speed ~ Fan 5 Speed
VCORE
12V
VDIMM
5Vcc
PCH 1.05V
AVCC
3.3Vcc
VSB
VBAT
4-37
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
4-4 Boot Settings
Use this feature to configure Boot Settings:
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Main Advanced Boot Security Exit
Sets the system boot order
Set Boot Priority
1st Boot Device
2nd Boot Device
3rd Boot Device
4th Boot Device
5th Boot Device
6th Boot Device
[CD/DVD]
[Hard Disk]
[USB Hard Disk]
[Removal]
[Network: IBA GE Slot 00C8 v1410]
[UEFI: Built-in EFI ]
Hard Disk Drive BBS Priorities
Netwrok Device BBS Priorities
UEFI Boot Drive BBS Priorities
:
Enter: Select
Select Screen
Select Item
:
Add New Boot Option
Delete Boot Option
+/-
F1 :
F2 :
F3 :
F4 :
:
Change Opt.
General Help
Previous Values
Optimized Defaults
Save & Exit
Add New Driver Option
Delete Driver Option
ESC :
Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Set Boot Priority
This option prioritizes the order of bootable devices that the system to boot from.
Press [ENTER] on each entry from top to bottom to select devices.
•
•
•
•
•
•
1st Boot Device
2nd Boot Device
3rd Boot Device
4th Boot Device
5th Boot Device
6th Boot Device
Hard Disk Drive BBS Priorities
•
1st Device
•
2nd Device
UEFI Boot Drive BBS Priorities
•
1st Boot Device
4-38
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: AMI BIOS
Delete Boot Option
Use this feature to remove a pre-defined boot device from which the system will
boot during startup. The settings are [any pre-defined boot device]
Delete Driver Option
Use this feature to remove a pre-defined driver from which the system will boot
during startup. The settings are [any pre-defined boot device]
4-39
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
4-5 Security Settings
This menu allows the user to configure the following security settings for the
system.
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Main Advanced
Password Description
Boot Security Exit
Set Administrator Password.
If ONLY the administrator’s password is set,
then this only limits access to Setup and is
only asked for when entering Setup.
If ONLY the User’s password is set, then this
is a power on password and must be entered to
boot or enter Setup. In Setup the User will
have Administrator rights.
The password length must be
in the following range:
Minimum length
3
Maximum length
20
:
Enter:
Select Screen
Select Item
Select
:
Administrator Password
+/-
:
Change Opt.
General Help
Previous Values
Optimized Defaults
Save & Exit
F1 :
F2 :
F3 :
F4 :
ESC :Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
•
•
•
If the Administrator password is defined ONLY - this controls access to the
BIOS setup ONLY.
If the User's password is defined ONLY - this password will need to be entered
upon each system boot, and will also have Administrator rights in the setup.
Passwords must be at least 3 and up to 20 characters long.
Administrator Password
Use this feature to set the Administrator Password which is required to enter the
BIOS setup utility. The length of the password should be from 3 characters to 20
characters long.
HDD Security Configuration
Use this feature to set the Hard Disk Drive Password which will be required to
access the selected hard disk drive. The length of the password should be from 3
characters to 20 characters long. To begin, use the cursor to highlight a detected
hard disk and press <Enter>. Press <Enter> again on "Set User Password" to
define the hard disk drive password. Save when finished.
4-40
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: AMI BIOS
4-6 Save & Exit
Select the Exit tab from the BIOS Setup Utility screen to enter the Exit BIOS Setup
screen.
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Main Advanced
Boot
Security
Exit
Exit system setup after saving the
changes.
Discard Changes and Exit
Save Changes and Reset
Save Options
Save Changes
Discard Changes
Restore Optimized Defaults
Save as User Defaults
Restore User Defaults
:
Enter:
Select Screen
Select Item
Select
Change Opt.
General Help
Previous Values
Optimized Defaults
Save & Exit
Boot Override
WDC WD2500SY-01SHB1
UEFI: Built-in EFI Shell
:
+/-
:
F1 :
F2 :
F3 :
F4 :
ESC :Exit
Version 2.15.1236. Copyright (C) 2012 American Megatrends, Inc.
Discard Changes and Exit
Select this option to quit the BIOS Setup without making any permanent changes
to the system configuration, and reboot the computer. Select Discard Changes and
Exit from the Exit menu and press <Enter>.
Save Changes and Reset
When you have completed the system configuration changes, select this option to
leave the BIOS Setup Utility and reboot the computer for the new system configura-
tion parameters can take effect. Select Save Changes and Exit from the Exit menu
and press <Enter>.
Save Options
Save Changes
When you have completed the system configuration changes, select this option to
save all changes made. This will not reset (reboot) the system.
Discard Changes
Select this option and press <Enter> to discard all the changes and return to the
AMI BIOS Utility Program.
Restore Optimized Defaults
To set this feature, select Restore Defaults from the Exit menu and press <Enter>.
These are factory settings designed for maximum system performance but not for
maximum stability.
4-41
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
Save As User Defaults
To set this feature, select Save as User Defaults from the Exit menu and press <En-
ter>. This enables the user to save any changes to the BIOS setup for future use.
Restore User Defaults
To set this feature, select Restore User Defaults from the Exit menu and press <En-
ter>. Use this feature to retrieve user-defined settings that were saved previously.
Boot Override
Listed on this section are other boot options for the system (i.e., Built-in EFI shell).
Select an option and press <Enter>. Your system will boot to the selected boot
option.
4-42
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: POST Error Beep Codes
Appendix A
BIOS Error Beep Codes
During the POST (Power-On Self-Test) routines, which are performed each time
the system is powered on, errors may occur.
Non-fatal errors are those which, in most cases, allow the system to continue
with bootup. The error messages normally appear on the screen.
Fatal errors will not allow the system to continue to bootup. If a fatal error oc-
curs, you should consult with your system manufacturer for possible repairs.
These fatal errors are usually communicated through a series of audible beeps.
The numbers on the fatal error list correspond to the number of beeps for the
corresponding error.
A-1 BIOS Error Beep Codes
BIOS Error Beep Codes
Beep Code/LED
Error Message
Description
1 beep
Refresh
Circuits have been reset.
(Ready to power up)
5 short beeps + 1 long
beep
Memory error
No memory detected in the
system
5 short beeps
OH LED On
Display error
System OH
System display error
System Overheat
A-1
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
Notes
A-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B: Software Installation Instructions
Appendix B
Software Installation Instructions
B-1 Installing Drivers
After you've installed the Windows Operating System, a screen as shown below
will appear. You are ready to install software programs and drivers that have not
yet been installed. To install these software programs and drivers, click the icons
to the right of these items. (Note: To install the Windows Operating System, please
refer to the instructions posted on our website at http://www.supermicro.com/
support/manuals/.)
Driver/Tool Installation Display Screen
Note 1. Click the icons showing a hand writing on the paper to view the
readme files for each item. Click on a computer icon to the right of an item
to install this item (from top to the bottom), one at a time. After installing
each item, you must reboot the system before proceeding with the next
item on the list. The bottom icon with a CD on it allows you to view the
entire contents of the CD.
Note 2. When making a storage driver diskette by booting into a Driver
CD, please set the SATAConfiguration to "Compatible Mode" and configure
SATA as IDE in the BIOS Setup. After making the driver diskette, be sure
to change the SATA settings back to your original settings.
B-1
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
B-2 Configuring SuperDoctor® III
The SuperDoctor III program is a Web-based management tool that supports remote
management capability. It includes Remote and Local Management tools. The local
management tool is called the SD III Client. The SuperDoctor III program included
on the CDROM that came with your motherboard allows you to monitor the envi-
ronment and operations of your system. SuperDoctor III displays crucial system
information such as CPU temperature, system voltages and fan status. See the
Figure below for a display of the SuperDoctor III interface.
Note: 1 The default user name and password are ADMIN.
Note 2: In the Windows OS environment, the SuperDoctor III settings take pre-
cedence over the BIOS settings. When first installed, SuperDoctor III adopts the
temperature threshold settings previously set in BIOS. Any subsequent changes
to these thresholds must be made within SuperDoctor, since the settings over-
ride the BIOS settings. For the Windows OS to adopt the BIOS temperature
threshold settings, please change the SD III Client settings to be the same as
those set in BIOS.
SuperDoctor III Interface Display Screen-I (Health Information)
B-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B: Software Installation Instructions
SuperDoctor III Interface Display Screen-II (Remote Control)
Note: The SuperDoctor III software and manual may be downloaded from our
Website at:
http://www.supermicro.com/products/accessories/software/SuperDoctorIII.cfm.
For Linux, we still recommend that you use SuperDoctor II, this version is also
available for download at the link above.
B-3
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
Notes
B-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C: UEFI BIOS Recovery
Appendix C
UEFI BIOS Recovery Instructions
Warning: Do not upgrade the BIOS unless your system has a BIOS-related issue.
Flashing the wrong BIOS can cause irreparable damage to the system. In no event shall
Supermicro be liable for direct, indirect, special, incidental, or consequential damages
arising from a BIOS update. If you need to update the BIOS, do not shut down or reset
the system while the BIOS is updating to avoid possible boot failure.
C-1 An Overview to the UEFI BIOS
The Unified Extensible Firmware Interface (UEFI) specification provides a software-
based interface between the operating system and the platform firmware in the
pre-boot environment. The UEFI specification supports an architecture-independent
mechanism for add-on card initialization to allow the UEFI OS loader, which is stored
in the add-on card, to boot up the system. UEFI offers a clean, hands-off control
to a computer system at bootup.
C-2 How to Recover the UEFI BIOS Image (-the Main
BIOS Block)
A UEF BIOS flash chip consists of a recovery BIOS block, comprised of two boot
blocks and a main BIOS block (a main BIOS image). The boot block contains critical
BIOS codes, including memory detection and recovery codes for the user to flash
a new BIOS image if the original main BIOS image is corrupted. When the system
power is on, the boot block codes execute first. Once that is completed, the main
BIOS code will continue with system initialization and bootup.
Note: Follow the BIOS Recovery instructions below for BIOS recovery
when the main BIOS boot crashes. However, when the BIOS boot block
crashes, you will need to follow the procedures in Appendix D.
C-3 To Recover the Main BIOS Block Using a USB-
Attached Device
This feature allows the user to recover a BIOS image using a USB-attached device
without additional utilities used. A USB flash device such as a USB Flash Drive, or
a USB CD/DVD ROM/RW device can be used for this purpose. However, a USB
Hard Disk drive cannot be used for BIOS recovery at this time.
C-1
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
To perform UEFI BIOS recovery using a USB-attached device, follow the instruc-
tions below.
1. Using a different machine, copy the "Super.ROM" binary image file into the
disc Root "\" Directory of a USB device or a writeable CD/DVD.
Note: If you cannot locate the "Super.ROM" file in your driver disk, visit
our website at www.supermicro.com to download the BIOS image into
a USB flash device and rename it "Super ROM" for BIOS recovery use.
2. Insert the USB device that contains the new BIOS image ("Super.ROM") into
your USB drive and power on the system
3. While powering on the system, keep pressing <Ctrl> and <Home> simultane-
ously on your keyboard until your hear two short beeps. This may take from a
few seconds to one minute.
4. After locating the new BIOS binary image, the system will enter the BIOS
Recovery menu as shown below.
Note: At this point, you may decide if you want to start with BIOS Recov-
ery. If you decide to proceed with BIOS Recovery, follow the procedures
below.
5. When the screen as shown above displays, using the arrow key, select the
item- "Proceed with flash update" and press the <Enter> key. You will see the
progress of BIOS Recovery as shown in the screen below.
Note: Do not interrupt the process of BIOS flashing until it is com-
pleted.
C-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C: UEFI BIOS Recovery
6. After the process of BIOS Recovery is complete, press any key to reboot the
system.
7. Using a different system, extract the BIOS package into a bootable USB flash
drive.
8. When a DOS prompt appears, enter AMI.BAT BIOSname.### at the prompt.
Note: Do not interrupt this process until BIOS flashing is completed.
C-3
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
9. After seeing the message that BIOS update is completed, unplug the AC pow-
er cable from the power supply to clear CMOS, and then plug the AC power
cable in the power supply again to power on the system.
10. Press <Del> continuously to enter the BIOS Setup utility.
11. Press <F3> to load default settings.
12. After loading default settings, press <F4> to save the settings and exit the
BIOS Setup utility.
C-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D: Dual Boot Block
Appendix D
Dual Boot Block
D-1 Introduction
This motherboard supports the Dual Boot Block feature, which is the last-ditch
mechanism to recover the BIOS boot block. This section provides an introduction
to the feature.
BIOS Boot Block
A BIOS boot block is the minimum BIOS loader required to enable necessary
hardware components for the BIOS crisis recovery flash that will update the main
BIOS block. An on-call BIOS boot-block corruption may occur due to a software
tool issue (see image below) or an unexpected power outage during BIOS updates.
-----------------------------------------------------------------------------------------------------------------
AMI Firmware Update Utility vX.XX.XX
Copyright (C)XXXX American Megatrends Inc. All Rights Reserved.
-----------------------------------------------------------------------------------------------------------------
Reading flash . . . . . . . . . . . . . . . . . . . . . . done
-- ME Data Size checking . ok
-- FFS checksums . . . . . . . . ok
Erasing Boot Block . . . . . . . . . . . done
__Updating Boot Block . . . . . . . . 0x00A91000 (13%)
BIOS Boot Block Corruption Occurrence
When a BIOS boot block is corrupted due to an unexpected power outage or a
software tool malfunctioning during BIOS updates, you can still reboot the system
by closing pins 2 and 3 using a cap on Jumper JBR1. When JBR1 is set to pins
2 and 3, the system will boot from a backup boot block pre-loaded in the BIOS by
the manufacturer.
D-1
Download from Www.Somanuals.com. All Manuals Search And Download.
C7Z87-OCE User’s Manual
D-2 Steps to Reboot the System by Using Jumper JBR1
1. Power down the system.
2. Close pins 2-3 on Jumper JBR1, and power on the system.
3. Follow the BIOS recovery SOP listed in the previous chapter (Appendix C).
4. After completing the steps above, power down the system.
5. Close pins 1-2 on Jumper JBR1, and power on the system.
D-2
Download from Www.Somanuals.com. All Manuals Search And Download.
(Disclaimer Continued)
The products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices,
aircraft/emergency communication devices or other critical systems whose failure to perform be reasonably expected to result in significant injury or loss of life or catastrophic
property damage. Accordingly, Supermicro disclaims any and all liability, and should buyer use or sell such products for use in such ultra-hazardous applications, it does so
entirely at its own risk. Furthermore, buyer agrees to fully indemnify, defend and hold Supermicro harmless for and against any and all claims, demands, actions, litigation, and
proceedings of any kind arising out of or related to such ultra-hazardous use or sale.
Download from Www.Somanuals.com. All Manuals Search And Download.
|