24-pin Dot-matrix Printer
FB-90
0
OWNER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can raditae frequency energy and, if not installed and
used in strict accordance with the instructions, may cause harmful interference to radio
communications. However there is no guaratee that interfernce will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television recption, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
—
—
—
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—
Consult the dealer ro an experienced radio/TV technician for help.
“It is necessary to use shielded interconnect cables to insure compliance with FCC Class
B limits for radio frequency emissions.”
Caution : Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
1.
2.
3.
No part of this manual may be reproduced in any form.
This manual is subject to change without notice.
This manual was prepared with the greateset care. If you should find any unclear points,
mistakes, or omissions, please contact us.
4.
We will not bear any responsibility for unsatisfactory results from the use of this printer
despite item 3 above.
*
*
*
*
*
*
*
EPSON is a registered trademark of S.Epson Corporation.
LQ-2550 is a registered trademark of S.Epson Corporation.
IBM is a registered trademark of International Business Machines Corporation.
IBM 2391 is a registered trademark of International Business Machines Corporation.
HP is a registered trademark of HEWLETT-PACKARD Company.
PCL is a registered trademark of HEWLETT-PACKARD Company.
DeskJet 500 / RuggedWriter 480 are registered trademarks of HEWLETT-PACKARD
Company.
*
Windows is a registered trademark of Microsoft Corporation.
Copyright © 1999 SEIKO Precision Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can raditae frequency energy and, if not installed and
used in strict accordance with the instructions, may cause harmful interference to radio
communications. However there is no guaratee that interfernce will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television recption, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
—
—
—
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—
Consult the dealer ro an experienced radio/TV technician for help.
“It is necessary to use shielded interconnect cables to insure compliance with FCC Class
B limits for radio frequency emissions.”
Caution: Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
1.
2.
3.
No part of this manual may be reproduced in any form.
This manual is subject to change without notice.
This manual was prepared with the greateset care. If you should find any unclear points,
mistakes, or omissions, please contact us.
4.
We will not bear any responsibility for unsatisfactory results from the use of this printer
despite item 3 above.
*
*
*
*
*
*
*
EPSON is a registered trademark of S.Epson Corporation.
LQ-2550 is a registered trademark of S.Epson Corporation.
IBM is a registered trademark of International Business Machines Corporation.
IBM 2391 is a registered trademark of International Business Machines Corporation.
HP is a registered trademark of HEWLETT-PACKARD Company.
PCL is a registered trademark of HEWLETT-PACKARD Company.
DeskJet 500 / RuggedWriter 480 are registered trademarks of HEWLETT-PACKARD
Company.
*
Windows is a registered trademark of Microsoft Corporation.
Copyright © 1996 SEIKO Precision Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
FB-900
OWNER'S MANUAL
24-pin Wide-Carriage
Dot Matrix Printer
As an ENERGY STAR Partner, SEIKO Precision Inc. has determined that this product meets
the ENERGY STAR guidelines for energy efficiency.
- Outline of the International ENERGY STAR Office Equipment Program -
The International ENERGY STAR Office Equipment Program is an international program
that promotes energy saving through the use of computers and other office equipment. The
program backs the development and dissemination of products with functions that effectively
reduce energy consumption. It is an open system in which business proprietors can participate
voluntarily. The targeted products are office equipment such as computers, displays, printers, facsimiles,
and copiers. Their standards and logos uniform among participating nations.
C
1999 SEIKO Precision Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use this maunal
This manual describes the operation procedures for the 24-Pin Wide-Carriage Dot
Matrix Printer. Read through this manual before using the printer. Keep this
manual near the printer and refer to it whenever necessary.
Precautions for use
Sections 1 and 2 describe the basic procedures, including unpacking, setup and
key operations. Install and setup the printer as described in these sections.
Section 3 and subsequent sections describe the functions and software commands
of the printer. Refer to these sections when necessary.
Organization of this manual
This manual is organized as shown below.
1. Setting up the printer
2. Control panel operations
3. Setup options
4. Functions
5. Bar code and enlarged character function
6. Troubleshooting
7. Interface specifications
8. Software commands
9. Software setup functions
10. Specifications
11. Character set table
Index
Software command list
Read this manual thoroughly to use the printer properly.
—How to use this manual—
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use this maunal
Symbols used in this manual
The symbols used in this manual have the following meanings.
This symbol indicates that personal injury
! CAUTION
may occur if this caution warning is ignored.
A caution symbol
Care should be taken in order to operate the
printer correctly.
Caution
This symbol indicates a note that is useful for
operation.
These item numbers show the sequence of
operation. Perform the operations in the
order shown.
1.
2.
3.
Display on the LCD before
the key is pressed
Display on the LCD
Press the
key.
1. MULTIPART
To the next step
2.HEAD ADJUSTMENT
Display on the LCD after the
key is pressed
—How to use this manual—
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
How to use this manual
Cautions for use
Preface
2. Control panel
operations......................... 2-1
●●Control panel operations................... 2-1
Control panel............................ 2-1
Fuction keys............................. 2-1
Organization of this manual
Symbols used in this manual
● Cautions................................................. iv
Safety Cautions............................ iv
Cautions in setting up.................. iv
Cautions in operation................... iv
3. Setup options.................................... 3-1
Outline of the
setup modes..... ......3-1
●●Components and functions................ viii
Appearance of the printer........... viii
setup modes........... 3-1
Entering the setup
modes.................... 3-1
●●Operations on the setup mode...........3-2
Keys for setting......................... 3-2
Setting example in EXTENDED
SETUP MODE.... 3-3
#15 Paper Fastener................................ 3-22
#16 Perforation...................................... 3-22
#17 Fanfold feed.................................... 3-23
#18 Paper Quality.................................... 3-23
#19 Saving data in format memory...... 3-24
1. Setting up the printer...................... 1-1
the power source.................. 1-1
●●Installing the ribbon cassette........... 1-2
Installing the ribbon cassette..1-2
●●Paper path............................................ 1-4
Path of fanfold paper................ 1-4
●●Loading fanfold paper
(Front tractor)..........................1-12
●●Loading cut sheet paper
(Manual paper feeding)............ 1-19
●●Printing using the cut sheet feeder
(Optional).............................1-22
●●Connecting the printer to
Parallel interface....................1-28
memory................................ 3-24
#20 Emulation........................................ 3-25
#21 Character table (HP)....................... 3-25
#22 Character table (EPSON)............... 3-26
#23 Character table (IBM).................... 3-26
●●Link between paper path (PATH)
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
#83 Data latch timing
(Parallel I/F)....................... 3-53
#25 Code page...................................... 3-28
#90 Printing direction........................... 3-55
#91 Display language on LCD............. 3-55
#92 Locking panel keys........................ 3-56
(IBM).................................. 3-28
#27 CR code function............................ 3-29
#28 LF code function............................ 3-29
#29 Accent character............................ 3-30
#30 Zero font style................................ 3-30
#31 Horizontal tab................................ 3-31
#32 Locking page length...................... 3-31
#33 Locking font................................... 3-32
#34 Locking character pitch................. 3-32
#35 Locking character quality.............. 3-33
#36 Locking character table.................. 3-33
#40 Validity of bar code and
#93 Locking reset key........................... 3-56
#94 Printing panel setting..................... 3-57
#95 Printing setup list........................... 3-57
4. Functions........................................ 4-1
●●High speed printing............................. 4-1
●●Enhancing the copying capability
●●Setting the printing start position........ 4-2
●●Feeding perforation to the cutter
enlarged character................ 3-36
●●More stable paper feeding.................. 4-3
●●Automatically feeding perforation to the paper
cutter position in the standby condition.. 4-4
●●Executing test printing......................... 4-9
●●Key shortcut function........................... 4-9
●●Connecting the printer in the
#42 Bar code size................................... 3-39
#43 Enlarged character size.................. 3-39
#44 Software setup................................ 3-40
#50 PCL mode (HP).............................. 3-40
#51 Secondary character table (HP).... 3-41
#60 Setting option.................................. 3-41
#61 Paper path....................................... 3-42
#62 Automatic scrolling........................ 3-42
#63 Out-of-paper detection.................... 3-43
#64 Skew detection............................... 3-43
#65 Paper jam detection....................... 3-44
#66 Line feed speed.............................. 3-44
#71 Printer select command................... 3-47
#72 Parity bit (Serial I/F)................... 3-47
#73 Data length (Serial I/F)............... 3-48
#74 Stop bit (Serial I/F)...................... 3-48
#75 Protocol (Serial I/F)..................... 3-49
#76 Baud rate (Serial I/F)................... 3-49
#77 Serial error (Serial I/F)................ 3-50
#78 CTS signal (Serial I/F)................. 3-50
#79 CD signal (Serial I/F)................... 3-51
#80 DSR signal (Serial I/F)................. 3-51
#82 BUSY/ACK signal timing
HP envioronment................. 4-12
5. Bar code and enlarged
character function................. 5-1
●●Bar code type.......................................5-1
Outline of bar code function........ 5-1
Makeup of bar code....................... 5-1
Presettable bar code function list.5-2
Bar code command list................. 5-2
(1) Bar code type.......................................... 5-2
(2) Element width........................................ 5-3
(4) Setting HRI on and off........................... 5-3
(5) HRI font.................................................. 5-4
(6) Check character.................................... 5-4
(Parallel I/F)....................... 3-53
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
5-5
characters................................ 5-21
(11) HMI for enlarged characters............... 5-21
(12) VMI for enlarged characters............... 5-22
character mode...................... 5-22
(8) Ending the bar code data sequence....
(9) Bar code data sequence......................... 5-5
(10) Printing density.................................... 5-5
(11) Guide bar expansion............................ 5-5
(12) Start and stop characters..................... 5-6
(13) Barcode rotational angle...................... 5-6
(14) Enlarged character cell offset............ 5-23
(15) Enlarged character pitch.................... 5-23
(16) Enlarged character quality.................... 5-24
(17) Enlarged character rotational angle..... 5-24
(18) Setting and canceling enlarged
and stop characters................... 5-6
(15) Value input mode.................................. 5-6
(16) Initializing the bar code mode.............. 5-7
(19) Enlarged character top offset............... 5-25
(20) Setting and canceling underlining
of enlarged characters.............. 5-26
Additional explanation of bar code
commands................................. 5-7
●
Data processing in the bar
code data sequence................... 5-7
UPC-E conversion rule......................... 5-12
Calculating the check character............ 5-12
Other....................................................... 5-14
Element printing.................................... 5-14
(21) Enlarged character widthwise
expansition................................5-26
●
●
(22) Horizontal printing position for
enlarged characters.................. 5-27
(23) Vertical printing position for
enlarged characters.................. 5-27
●●Functional error messages................ 6-1
●●Enlarged character function........... 5-16
function................................... 5-16
7. Interface specifications............... 7-1
Enlarged character command list..
5-16
Input connector......................... 7-1
Pin configuration...................... 7-1
Timing chart.............................. 7-2
Input/output conditions............. 7-2
Signal explanations................... 7-3
Input signals to the printer........ 7-3
(1) Executing backspacing......................... 5-17
(2) Executing line feeding.......................... 5-17
(3) Executing form feeding........................ 5-18
(4) Executing carriage return..................... 5-18
(5) Initializing the
enlarged character mode........ 5-18
(6) Arrangement of enlarged characters..... 5-19
characters............................... 5-19
●●Serial interface.................................... 7-5
Input connector........................ 7-5
Pin configuration...................... 7-5
Timing chart.............................. 7-5
(8) All-character set for enlarged
(9) Selecting an enlarged character font..... 5-20
(10) Height expansion for enlarged
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Handshaking protocol................ 7-8
protocol.................. 7-8
ISO-1 (ISO-8859-1)..................................11-5
Code page 858.......................................... 11-5
Code page 861.......................................... 11-6
Code page ABICOMP...............................11-6
ROMAN-8 character set (HP)....................11-7
PC-8 character set (HP).............................11-7
MATH 7 character set (HP)........................11-7
LINE DRAW character set (HP).................11-8
International character set (HP) [ISO].........11-8
ETX/ACK protocol................. 7-11
Baud rate................................. 7-11
Automatic serial/parallel
selection.......................... 7-11
●●EPSON Software command........... 8-1
9. Software setup functions.......... 9-1
●●Command format............................... 9-1
10. Specifications................................ 10-1
●●Printing specifications.......................10-1
●●Graphic printing specifications.......... 10-5
●●Throughput...................................... 10-5
●●Paper specifications.......................... 10-6
●●Other specifications.......................... 10-6
11. Character set table.................... 11-1
EPSON extenced graphic table...................11-1
EPSON international font table.................. 11-2
IBM character set table 1...........................11-2
IBM character set table 2...........................11-3
IBM all-character set table.........................11-3
Code page 437........................................ 11-4
Code page 850........................................ 11-4
Code page 857 ........................................11-4
Code page 860 .......................................11-4
Code page 863........................................ 11-5
Code page 865........................................ 11-5
Download from Www.Somanuals.com. All Manuals Search And Download.
● Major functions
This printer provides a wide range of print functions, as shown below:
●●High-speed printing
Prining mode
DRAFT (10 cpi)
LQ (10 cpi)
Pirnt speed
603 CPS
180 CPS
240 CPS
360CPS
723 CPS
904 CPS
Throughput
206 LPM (132 columns)
76 LPM (132 columns)
100 LPM (132 columns)
135 LPM (132 columns)
230 LPM (132 columns)
270 LPM (132 columns)
NLQ (10 cpi)
HQDR (10 cpi)
S.D. (12 cpi only)
S.S.D. (15 cpi only)
●●Original plus 8 multipart forms printing
The printer can print data on an original and up to eight
copies. Copy density can be enhanced by selecting the
DARK 1 (high pressure), DARK 2 (very high pressure) or
AUTO (automatic print pressure adjustment by sensing
the form set thickness). This setting is made in the
MULTIPART function of the SETUP MODE.
●●: If DARK 1 or DARK 2 is selected, the printing
speed is reduced below the normal print speed
to compensate for the extra energy required
when printing in the high pressure print
modes.
●●Bar code printing function
A variety of bar codes of this printer may be printed. The
narrow and wide spaces, narrow and wide bars, HRI,
check character, bar code height, and rotation may be
controlled with software commands. Customized bar
codes may also be printed using the element funcion.
Registered bar code formats: Industrial 2 of 5, Interleaved 2
of 5, Matrix 2 of 5, Codabar, Code11, Code 39 , Code 93,
Code 128, EAN-8, EAN-13, UPC-A, UPC-E, and Postnet
●●Enlarged character printing
Characters can be enlarged (by up to 127 times as large x
127 times as large) using the enlarged character command
unique to this printer. Software commands are used for
control.
i
Download from Www.Somanuals.com. All Manuals Search And Download.
● Major functions
● Zooming function (Batch enlargement or reduction printing)
● Cut sheet paper manually loading
● Skew sensor
A built-in skew sensor detects any cut sheets that are
skewed when loaded and ejects them.
● Automatic head adjustment
The printer employs an automatic paper thickness
detection sensor, instead of the conventional paper
thickness adjust lever, for optimum printing on all form
sets.
● Automatic loading (For fanfold or cut sheet paper)
● Perforation cutting (For fanfold paper)
By pressing the TEAR OFF key, the perforation of fanfold
paper is automatically fed to the paper cutter position.
● Paper parking (Switching fanfold paper and cut sheet paper)
If cut sheet paper is selected while fanfold paper is used,
the fanfold paper is automatically fed back to the parking
position (i.e., paper parking).
● Load adjustment
The pritning start position may be adjusted within a
range from approximately 0 to 26.7 mm from the top of
the paper. It is recommended that the printing position
be in the center of the paper in the range of 4 mm or less
from the the top of the paper.
● MICRO REVERSE LF and MICRO LF keys
These keys are useful for adjusting the printing start
position and paper cutting position.
●Automatic scroll (For fanfold paper)
If no data input is recived for a preset period (0.5, 1, 5,
10, 15 sec.), the perfpration of the current page of fanfold
paper is fed to the paper cutter position.
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
●Dual paper parking
If the optional rear tractor is used, two different types of
fanfold paper may be used. Software command or the
PAPER PATH key can be used for selection.
● Large 512KB communication buffer
● Setup memory for setting various functions on the LCD
● Ten resident fonts
● Line feed speed adjustment
Standard, 1/2 or 1/3 line feed speed is selectable for
stable paper feeding even when multipart paper is used.
● Vertical alignment function
● Serial data transfer at a maximum rate of 38.4k bps
● Parallel and serial interfaces are standard
Parallel and serial interface are switched automatically.
● Printing stops immediately if the printer cover is
inadvertently opened during printing.
● Enegy Star
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
● Caution
Safety Cautions
! CAUTION
● Do not touch the print head immediately
● Use two hands and hold firmly at each
end when lifting the cut sheet feeder.
Personal injury can occur if the CSF unit
is dropped.
after printing because it is too hot.
● Do not put your finger under the tractor
cover while loading fanfold paper.
Cautions in setting up
Caution
● Unpack the printer. Make sure that the
printer body and all accessories are
included in the package and no parts are
damaged.
●●Place the printer on a rigid, horizontal
base in a location that is free of vibration.
● Before connecting or disconnecting the
interface cable, be sure to turn off the
printer.
● Do not use the printer in a location
exposed to direct sunlight or close to a
heater or other heat generating
equipment.
● Do not connect the printer to a non-
standard power source.
● Do not use the printer in a dusty location
or any location subject to sudden
changes in temperature and humidity.
Cautions in operation
Caution
● If any foreign matter gets into the
printer, turn off the printer
immediately and remove the foreign
matter.
●●Never try to print without a ribbon
cassette installed and paper loaded.
●
Push the lock levers of both tractors
to the LOCK positions firmly while
loading fanfold paper or single sheet
paper. It is for the purpose of
setting paper path securely.
●
If the case or cover becomes dirty,
clean it with a soft cloth moistened
with a small quantity of neutral
detergent diluted with water. Never
use a hard cloth or volatile solvent
such as alcohol, thinner, or benzine.
See page 3-1.
● Do not turn off the printer during
printing, as this may lead to a
malfunction.
●
Take care not to twist the ribbon while
installing the ribbon cassette.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
● Unpacking the printer
Unpacking the printer
● The printer body weights approximately 24 kg [52.9 lbs.]. It should be
taken out of the package by two or more persons.
Make sure that no parts of the printer are damaged.
24-pin Dot-matrix Printer
FB-900
Hand book
Ribbon Cassette
Hand book
Top Paper Rack
CD-ROM
Printer
Power Cord
v
Download from Www.Somanuals.com. All Manuals Search And Download.
● Unpacking the printer
● Check the carton for the following items:
●Printer
●Ribbon cassette
#SBP-1051
●Top paper rack
Attach the top paper rack to
eject paper to the top of the
printer. Sheets of paper are
stacked on this rack.
●Power cord
Connect this power cord to an
AC outlet.
Caution
24-pin Dot-matrix Printer
●Hand book
0
FB-90
If some part is not
included in the package,
contact the dealer where
you purchased the
printer.
Hand book
●
CD-ROM
Keep the carton and
packaging material.
They are needed for
transporting the printer
or returning it for
service if ever required.
Driver-CD with Owner's
Manual, printer driver
software.
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
● Dimensions
The following drawings show the outside dimensions of the printer.
●
505mm
395mm
Caution
The weight of the
printer including the
ribbon cassette is
approximately 24 kg
[52.9 lbs.]. Two
persons should carry
the printer.
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
● Components and functions
Appearance of the printer
1. Paper Guide (for Manual Feeding)
2. Paper Stacker (for Cut Sheet Feeder)
3. Liquid Crystal Display (LCD)
4. Control Panel
7. Front Cover Lock Release Button
5. Paper Rack
LCD: PAPER RACK
6. Paper Support Guide (for Manual Feeding)
8. Front Cover
LCD: FRONT COVER
9. Ribbon Cassette
10. Print Head
11. Power Switch
13. Top Paper Rack
20. Paper Cutter
14. Top Cover
12. Tractor
LCD: TOP COVER
15. Rear Cover
LCD: REAR COVER
16. AC Receptacle
17. Serial Connector
18. Parallel Connector
19. Rear Printer Cover
1
viii
Download from Www.Somanuals.com. All Manuals Search And Download.
● Components and functions
Components and functions
The names and functions of the printer components are shown below.
Name (See drawing on left.)
1. Paper guide
Function
Adjusts the printing position when feeding paper
manually.
2. Paper stacker
When the optional CSF is used, sheets of paper
are ejected into this paper stacker. Both sides of
the paper stacker should be set up.
3. Liquid crystal display (LCD)
4. Control panel
Displays the condition and settings of the printer.
Displays and sets the printer conditions.
If the “OPEN PAPER RACK” message is
desplayed on the LCD when setting the paper
path, open the paper rack.
5. Paper rack
6. Paper Support Guide
Guide the cut sheet at manuarl feeding.
To open the front cover, push the two buttons
located on the lower corners of the front cover.
To mount fanfold paper on tractors or replace the
ribbon cassette, open the front cover.
If printed characters vecome pale, replace the
ribbon cassette.
7. Front Cover Lock release button
8. Front cover
9. Ribbon cassette
10. Print head
Prints characters on paper.
11. Power switch
Pressing the power switch toggles the power on
and off.
ON: Switch depressed OFF: Switch released
The tractor pins engage sprocket holes on both
sides of fanfold paper for feeding.
12. Tractor
13. Top paper rack
14. Top cover
Ejected cut sheets are stacked on the top paper
rack.
Eject fanfold paper to the top of the printer. If
the “OPEN TOP COVER” is displayed on the
LCD when setting the paepr path, open the top
cover.
15. Rear cover
To eject fanfaold paper to the top of the prieter,
open the rear cover. If the “OPEN REAR
COVER” is displayed on the LCD when setting
the paper path, open the rear cover.
Connect the power to this AC receptacle. The
power is desigated on the rating plate on the back
of the printer.
16. AC receptacle
RS-232C interface connector
17. Serial connector
18. Parallel connector
19. Rear printer cover
Parallel interface connector
When the rear tractor or CSF is used, remove the
rear printer cover.
Cut the paper after pressing the TEAR OFF key.
20. Paper Cutter
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
● Components and functions
Control panel explanation 1
State display LCD
F
.
T
R
R
E
A
R
1
1
.
5
1
5
x
IN
OUT
FORM
PAPER PATH
State display Lamps
1
2
3
4
DATA ERROR ONLINE POWER
TEAR OFF
ONLINE
1
12
13
14
15
State display lamps
RESET
2
3
1
2
Blinks while data is transferred.
Lights while data is processed except
during communication or when the
input buffer contains data. Goes out
in other conditions.
PAPER FORM
PAPER PATH
TOF SET
4
5
EJECT/LOAD
FORM FEED
LINE FEED
ON : Paper is not detected some
other operational error has
occurred.
6
QUALITY
SET UP
7
8
OFF : Paper is detected.
Blinking : A functional error (such
as home sense error,
EXIT
EXTENDED
9
MICRO LF
16
17
internal RAM error,
paper path switching error,
head adjustment error,
REVERSE LF
10
11
ENTER
ALT
park error and skew error)
MICRO RLF
18
ON : Printing is enabled.
OFF : Printing is disabled.
Blinking : The cover is open, or
the printer is in the head
temperature protect
3
4
Key Panel
condition.
On when printer power is turned on.
x
Download from Www.Somanuals.com. All Manuals Search And Download.
● Components and functions
Control panel explanation 2
State display LCD
Paper Width (Fanfold Paper)
Orientation (Cut Sheet Paper)
15: 15 inches 12: 12 inches 10: 10 inches 5: 5 inches
p: Portrait l: Landscape
LT : LETTER
HLT : HALF LETTER
LG : LEGAL
EX : EXECUTIVE
GLT : GOVERNMENT LETTER
GLG : GOVERNMENT LEGAL
LD : LEDGER
F4 : F4 SIZE
PC : POST CARD
C6 : COMMERCIAL-6
C10 : COMMERCIAL-10
MN : MONARCH
F
.
T R
R E A R 1 1
.
5
x
1 5
Page Length (Fanfold Paper)
Paper Size (Cut Sheet Paper)
2 : 2 inches
Paper In
Paper Out
Page
Length
16.5 : 16.5 inches
A3 : A3
A4 : A4
F. TR : Front Tractor
R. TR : Rear Tractor
MAN : Manual
REAR : Rear
TOP : Top
FRNT : Front
A5 : A5
CSF
: Cut Sheet Feeder
DL : DL Envelope
C5 : C5 Envelope
1inch=25.4mm
Keys on the panel
Feeds the perforation of fanfold paper to the paper
cutter poistion. (For fanfold paper only)
When pressing the corresponding key while you
press the ALT key, one of the following
functions is executed.
1
11
(ALT + TEAR OFF keys)
2
MICRO LF
MICRO RLF
EXTENDED SETUP
QUALITY
TOF SET
RESET
LINE FEED
REVERSE LF
SET UP
EJECT/LOAD
PAPER PATH
TEAR OFF
Press these keys for two seconds or more. Release
the keys when "INITIAL" is displayed on the LCD.
The printer will be reset.
Changes the paper path display. To select the
displayed paper path, press the ENTER key.
3
4
(ALT + PAPER PATH keys)
When paper is loaded, the current printing position is
considered as the TOF position.
Changes the printing enable (online) state and
printing disable (offline) state.
12
13
5
6
Loads paper or feed back paper to the parking
position when fanfold paper is used. Loads or
and ejects paper when cut sheet paper is uesd.
Changes the paper form display. To select the
displayed paper form, press the ENTER key.
Feeds one page.
14
15
(ALT + EJECT/LOAD keys)
Changes the printing quality display. To select
the displayed mode, press the ENTER key.
Feeds one line in the forward direction at a pitch
of 1/6 inch.
Enters the SETUP MODE.
(ALT + LINE FEED keys)
Feeds one line in the forward direction at a pitch
of 1/360 inch.
7
16
Quits the SETUP MODE or EXTENDED
SETUP MODE.
8
(Micro line feed)
(ALT + SETUP keys)
Enters the EXTENDED SETUP MODE.
Feeds one line in the reverse direction at a pitch
of 1/6 inch.
17
18
9
Selects an item displayed in the SETUP MODE,
the EXTENDED SETUP MODE, setting the
paper path, setting the paper form or setting the
printing quality.
(ALT + REVERSE LF keys)
Feeds one line in the reverse direction at a pitch
of 1/360 inch.
10
(Micro reverse line feed)
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
● Options and consumables
Cut sheet feeder
Rear tractor
#FB-84009
#FB-84008
Dual paper parking is available when the rear
tractor is used. Two different types of paper may
be set onto the front and rear tractors and may be
selected by issuing software commands or
pressing the PAPER PATH key to change the
paper paths.
The cut sheet feeder feeds cut sheets automatically
and continuously. A maximum of 150 sheets of
paper (55 kg paper) may be set in the holder of the
cut sheet feeder.
For attaching the cut sheet feeder,
see pages 1-22 to 1-26.
For attaching the rear tractor, see pages 1-16 to 1-18.
Print head
Ribbon cassette
#SBP-1051
#FB-90090
For mounting the print head, refer to the manual
supplied with the print head.
For attaching the ribbon cassette,
see pages 1-2 and 1-3.
Current loop interface unit
RS-422A interface unit
#FB-84010
#FB-84011
This unit enables data to be transferred through
This unit converts serial data into 20 mA
current loop signals. This is a built-in unit that
is installed by the dealer. If the current loop
interface unit is installed, the RS-232C
interface cannot be used.
an RS-422A interface. This is a built-in unit
that is installed by the dealer. If the RS-422A
interface unit is installed, the RS-232C
interface cannot be used.
xii
Download from Www.Somanuals.com. All Manuals Search And Download.
● Maintenance
Periodic maintenance and inspection is recommended to keep
the printer in good condition.
● Remove paper particles or dust adhered to
the detection sensor cover upper surfaces
(three locations) inside the printer and to the
paper jam sensor surface (one location), by
wiping with a soft clth or a cotton bud. The
paper particles or dust on the sensor
surfaces may cause faulty operation.
Detection sensor
Detection sensor
Paper jam sensor
Do not use a hard brush to clean the
sensor cover and the sensor surface.
The brush may scratch the surface.
Caution
When opening the front cover just
after the printer has been in operation,
do not touch the printer heard which
is hot and may cause burns.
!
Caution
xiii
Download from Www.Somanuals.com. All Manuals Search And Download.
1.
Setting up the printer
Connect the AC power plug to an AC outlet of the voltage
designated on the rating plate on the back of the pirnter.
Caution
● Connecting the printer to Power
● Make sure that the power switch is set to off.
Connect the printer with the supplied power
cord to an AC outlet.
To AC outlet
●●The AC outlet shall be installed near the
printer and shall be easily accessible.
Once the printer is turned off, wait for three seconds or
more before turning it on again. If the printer is turned
on again within three seconds after turning it off, it
may malfunction due to an initializtion failure.
—
—
1. Setting up the printer
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
● Installing the ribbon cassette
Installing the ribbon cassette
Approximately 15 seconds after the printer is rutned on, the print head will move to
the left.
1.
Turn the ribbon feed knob on the ribbon
cassette counterclockwise to stretch the
ribbon tight.
Caution
Use the specified
ribbon cassette .
When power is turned
off, data in the buffer
is lost. Output all data
before turning off the
printer.
Ribbon feed knob
Stretch the ribbon
2.
3.
Turn off the power. Open the front cover.
Caution
Open the front cover by
pressing both side locks
with both hands. Hold
both sides with both
hands to raise it upward
slowly. When closing
the front cover, hold
both sides with both
hands to pull it down
slowly. Press the front
cover to lock it.
Power switch
Every press of the power
switch turns the power on
or off.
Front cover
Attach the ribbon cassette as shown below.
Print head position
Do not touch the print head immediately
after printing becouse it is too hot.
! CAUTION
—
—
1. Setting up the printer
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
● Installing the ribbon cassette
4.
Slide the ribbon toward the print head so
that the ribbon is lightly in contact with the
projection of the print head.
Projection
Slide
Slide
5.
Attach the cassette firmly to the mounting
plate.
Turn the ribbon feed knob
counterclockwise.
Fit the right and left projections on the mounting plate to the holes in
the bottom of the ribbon cassette.
Ribbon feed knob
6.
Close the front cover.
Pull down the front cover slowly toward you with both hands from
both sides to close it.
Push down on both sides at the bottom of the front cover to close it
firmy. Two hands are required to engage and lockthe front cover on
both sides.
—
—
1. Setting up the printer
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
● Paper path
Path of fanfold paper
The three fanfold paper paths shown below are available. For selecting a paper
path, See pages 1-6 and 1-7.
Front tractor
2
●
Inside of the printer viewed
from the right.
1
Liquid crystal display
Paper loading direction
F
.
T
R
R
E
A
R
1
1
x
1
5
1. Front loading, rear ejection
This paper path applies a smaller load to the paper.
This is recommended for printing on thick paper
(such as multipart paper or label sheets).
.
F
T
R
T
O
P
1
1
x
1
5
2. Front loading, top ejection
This paper path is recommended if fanfold paper is
cut along the perforation frequently.
The perforation is automatically fed to the paper
cutter of the top cover by pressing the TEAR OFF
key so that the paper may be torn off easily.
To cut the paper, hold the upper cover firmly with
one hand and tear the paper towards you.
Rear tractor (Option)
●
Inside of the printer viewed
from the right.
Paper loading
direction
3
Rear tractor
(Optional)
Paper rack
R
.
T
R
F
R
N
T
1
1
x
1
5
3. Rear loading, front ejection
Dual paper parking is available when the optional
rear tractor is used. Two types of fanfold paper of
different size and thickness may be used and
selected from the control panel or by issuing a
software command (ESC EM or software setup*)
from the computer.
* Software setup commands
The software setup commands are unique to this
printer. Most functions available on the SETUP
MODE and EXTENDED SETUP MODE can may
—
—
1. Setting up the printer
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
● Paper path
Path of cut sheet paper
The five cut sheet paper paths shown below are available.
●Sheets of paper are loaded manually one at a time.
Manual paper feeding
3
●
Inside of the printer
viewed from the right.
1
2
Paper loading
direction
M
A
N
F
R N
T
A
4
p
p
1. Front loading, front ejection
This paper path applies a lighter load on feeding paper. It is
recommended for printing on thick paper (such as multipart
paper, postcards, and envelopes).
2. Front loading, rear ejection
M
A
N
R
E
A
R
A
4
This paper path applies a lighter load on feeding paper. This
is recommended for printing on thick paper (such as
multipart paper, postcards, and envelopes).
3. Front loading, top ejection
M
A
N
T
O
P
A
4
p
This paper path enables face-down stacking.
Cut sheet paper (Option)
5
4
●
Inside of the printer
viewed from the right.
4. CSF loading, front ejection
C
S
F
F
R
N
T
A
4
p
This paper path is suitable for thick paper (such as multipart
paper, postcards and so on). Sheets of paper are stacked face-up.
5. CSF loading, top ejection
C
S
F
T
O
P
A
4
p
This paper path enables face-down stacking.
—
—
1. Setting up the printer
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
● Selecting the Paper path
The following shows an example of changing the paper path for reference. The
example shown below changes front tractor loading and rear ejection to the front
tractor loading and top ejection.
Selecting the paper path
1.
Press the PAPER PATH key.
The paper path currently selected is displayed.
F
.
T
R
R
E
A
R
1
1
x
1
5
P
A
T
H
:
F
.
T
R
.
-
>
R
E
A
R
IN
OUT
FORM
PAPER PATH
PAPER PATH
2.
Continue to press the PAPER PARH key until
“PATH: F. TR. -> TOP ” is displayed. Press
the ENTER key.
F
.
T
R
-
>
R
E
A
R
M
E
M
O
1
IN
OUT
FORM
PAPER PATH
PAPER PATH
F
F
.
T
R
-
>
T
O
P
M
E
M
O
1
IN
OUT
FORM
PAPER PATH
ENTER
-
>
T
O
P
.
T
R
1
1
x
1
5
IN
OUT
FORM
PAPER PATH
—
—
1. Setting up the printer
1-6
Download from Www.Somanuals.com. All Manuals Search And Download.
● Selecting the paper path
●Fanfold paper
F
.
T
R
R
E
A
R
EJECTION
EJEC-
TIO
N
1
LOAD
EJEC-
ON
TI
1
F
.
T
R
R
.
T
O
P
●Fanfold paper (Optional rear tractor)
T
R
F
R
N
T
EJEC-
TION
LOAD
1
●Cut sheet paper (Manual feeding)
M
A
N
F
R
N
T
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
EJECTION
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
LOAD
M
A
N
T
O
P
EJECTION
M
A
N
R
E
A
R
1
1
EJECTION
●Cut sheet paper (Optional cut sheet feeder)
LOAD
C
S
F
F
R
N
T
EJECTION
EJEC-
TION
1
1
C
S
F
T
O
P
The optional CSF and rear tractor cannot be used together. If the optional CSF or rear tractor is
installed, enable it by using the EXTENDED SETUP MODE (#60 option). If the option is not
enabled on the EXTENDED SETUP MODE, the paper path cannot be selected.
—
—
1. Setting up the printer
1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
● Paper
When fanfold paper is used, set the page length (#4 PAGE LENGTH) and paper
width (#5 PAPER WIDTH) on the SETUP MODE. For setting, see page 1-12.
Printing area on fanfold paper
5, 10, 15 inches
(#5 PAPER WIDTH on SETUP MODE)
0/60 inch - 63/60 inches
(#3 TOF ADJUSTMENT on SETUP
MODE)
0/6 inch - 15/6 inches
(#6 TOP MARGIN on SETUP
Sizes of fanfold paper are
generally shown in inches.
MODE)
One inch is 25.4 mm.
Printing area
0/6 inch - 15/6 inches
(#7 BOTTOM MARGIN on
SETUP MODE)
Perforation
Printing area
Multipart
form
Front tractor 3 ~ 16 inches (76 ~ 406mm)
Rear tractor 3 ~ 16.5 inches (76 ~ 420mm)
Label
form
Paper form
Paper width
Single
Paper quality
Number of sheets
Thickness
Wood-free paper
9 or less
1
1
Last page
0.08
~ 0.12mm
0.12
~ 0.59mm
0.12
~ 0.18mm
Paper weight
55 ~ 90kg 34kg x 9P 125kg or less
16 mm or more
16 mm or more
Calculating sizes of fanfold paper
Paper width
Sprocket holes are made on both sides
of fanfold paper at an interval of 0.5
inch, which can be used to calculate
the page length and width.
22 holes
0.5 inch
Page length
0.5 inch × 22 = 11 inches
The page length can be determined by
multiplying the number of sprocket
holes per page by 0.5 inch.
30 holes
To find the paper width, use another
sheet of fanfold paper and count the
number of sprocket holes.
Page width
0.5 inch × 30 = 15 inches
—
—
1. Setting up the printer
1-8
Download from Www.Somanuals.com. All Manuals Search And Download.
● Paper
Specify the paper size of cut sheet paper using #4 PAGE
LENGTH on the SETUP MODE. For setting, see page 1-19.
Printing area on cut sheet paper
2 mm or more
2 mm or more
Glued portion
Approx. 0.5 mm
0/60 inch - 63/60 inches
(#3 TOF ADJUSTMENT on SETUP
MODE)
Horizontally loaded
size A5 sheets and
postcards cannot be
ejected upward.
Non-carbon, middle carbon
and back carbon multipart
paper can be used.
The thickness of the bound
portion is the sum of the
paper thickness and 0.25 mm
or less.
Printing area
Standard-size form
Multipart paper
Use wood-free paper. Cut sheet paper can be
loaded manually or by using the CSF.
Envelopes and horizontally set post cards
cannot be printed by using the CSF.
Manual paper feeding
CSF paper feeing
Multipart
Multipart
Single
Card
Envelope
Single
Card
Paper form
Paper quality
Paper form
Paper quality
Number of sheets
Thickness (mm)
Paper weight
form
form
Wood-free Carbon or
Wood-free
paper
Wood-free
paper
Non-carbon
Wood-free paper
paper
non-carbon
9 or less
6 or less
1
1
1
1
1
Number of sheets
Thickness (mm)
Paper weight
0.5 or less
39 ~ 78kg
0.08 ~ 0.12 0.12 ~ 0.59 0.08 ~ 0.8
55 ~ 90kg 34kg x 9P
0.08 ~ 0.11 0.12 ~ 0.39 0.08 ~ 0.22
55 ~ 78Kg 34kg x 6P 55 ~ 165kg
140mm and over
Paper length
Available standards-size forms
Paper Size
Manual Feeding
CSF Feeding
Portrait
Landscape
Portrait
Landscape
A3
A4
A5
(297mm X 420mm)
(210mm X 297mm)
(148mm X 210mm)
(8.5" X 11")
(5.5" X 8.5")
(8.5" X 14")
Letter
Half Letter
Legal
Executive
(7.25" X 10.5")
Government Legal (8.5" X 13")
Government Letter (8" X 10.5")
Ledger
(11" X 17")
F4
(210mm X 330mm)
(100mm X 148mm)
(6 1/2" X 3 5/8")
(9 1/2" X 4 1/8")
(3 7/8" X 7 1/2")
(110mm X 220mm)
(162mm X 229mm)
Post card
Commercial -6
Commercial -10
Monarch
DL
C5
●1 Paper length 150mm (5.9inch) or less can not be ejected to the top.
●2 A3 (portrait) or Ledger (portrait) can not be stacked on the top paper rack.
—
—
1. Setting up the printer
1-9
Download from Www.Somanuals.com. All Manuals Search And Download.
● Selecting the paper form
Paper form selection 1
Sizes of up to six frequently-used forms may be stored in MEMO 1 to MEMO 6 in the internal memory.
Any of the stored sizes may be read out of the memory with the PAPER FORM key whenever necessary.
See page 1-31.
Factory default setting
PAPER FORM
1
1
1
1
1
1
I
I
I
N
N
N
x
x
x
1
5
I
N
1
2
3
F
.
T
R
R
E
A
R
1
1
x
1
5
IN
OUT
FORM
PAPER FORM
PAPER FORM
PAPER PATH
1
5
I
N
PAPER FORM
1
5
I
N
If the EEPROM is
initialized, preset form
sizes are replaced by the
factory default settings.
PAPER FORM
A
A
4
4
p
4
5
PAPER FORM
p
PAPER FORM
A
4
p
6
PAPER FORM
Liquid crystal display
Paper Width
Orientation
(Fanfold Paper) (Cut Sheet Paper)
15 15 inches
12: 12 inches
10: 10 inches
5: 5 inches
p: Portrait
l: Landscape
R E A R
.
T R
1
1
.
5
x
1 5
F
Page Length (Fanfold Paper)
Paper Size (Cut Sheet Paper)
2 : 2 inches
Page
Length
16.5 : 16.5 inches
A3 : A3
A4 : A4
GLT : GOVERNMENT LETTER
GLG : GOVERNMENT LEGAL
F4 : F4 SIZE
A5 : A5
PC : POST CARD
LT : LETTER
HLT : HALF LETTER
LG : LEGAL
LD : LEDGER
EX : EXECUTIVE
C6 : COMMERCIAL-6
C10 : COMMERCIAL-10
MN : MONARCH
DL : DL Envelop
C5 : C5 Envelop
—
—
1. Setting up the printer
1-10
Download from Www.Somanuals.com. All Manuals Search And Download.
● Selecting the paper form
Paper form selection 2
The following shows an example of setting form size for reference. The example below
shows how to change the size stored in MEMO 3 ( page length: 11 inches, paper width:
15 inches) to an A5 portrait form.
Specifying form size
1.
Press the PAPER FORM key.
The paper size currently selected is displayed.
F
.
T
R
R
E
A
R
1
1
x
1
5
1
1
x
1
5
I
N
1
I
N
IN
IN
OUT
OUT
PAPER FORM
PAPER FORM
PAPER FORM
PAPER PATH
PAPER PATH
2.
Continue to press the PAPER FORM key to
select MEMO 3 as shown below.
F
.
T
R
-
>
R
E
A
R
M
E
M
O
1
IN
OUT
FORM
PAPER PATH
PAPER PATH
F
.
T
R
-
>
T
O
P
M
E
M
O
1
IN
OUT
FORM
PAPER PATH
ENTER
-
>
T
O
P
F
.
T
R
1
1
x
1
5
IN
OUT
FORM
PAPER PATH
3.
4.
Specify the intended form size as shown
below.
F.TR REAR 11 x 15
PAGE:11 INCH
1. MULTIPART
SET UP
1. MULTIPART
SIZE: A5 p
4. PAGE LENGTH
SIZE: A5 p
SAVE?: YES
4. PAGE LENGTH
EXIT
ENTER
ENTER
F.TR REAR A5 p
SIZE: A5 p*
SAVE?: YES
4. PAGE LENGTH
The A5 portrait form is set in MEMO 3.
—
—
1. Setting up the printer
1-11
Download from Www.Somanuals.com. All Manuals Search And Download.
● Loading fanfold paper (Front tractor)
This section describes how to set fanfold paper for front loading and rear ejection
or front loading and top ejection. Before setting fanfold paper, it is necessary to
specify the page length, paper width, etc. on the SETUP MODE.
Fanfold paper setting procedures 1
1.
Check the rating of the fanfold paper to be
used that is marked on the side of the
package.
Fanfold paper rating marked on side of package (Example)
Rating
10
X
11
- 1P
Multipart paper
(Number of sheets)
Paper width
Page length
2.
Press the PAPER PATH key to select the
desired paper path.
F.TR
REAR 11 x 15
F.TR
TOP 11 x 15
Paper loading direction
Paper loading direction
1
1
—
—
1. Setting up the printer
1-12
Download from Www.Somanuals.com. All Manuals Search And Download.
● Loading fanfold paper (Front tractor)
Fanfold paper setting procedures 2
3.
Specify the page length using #4 PAGE
LENGTH on the SETUP MODE as shown
below.
F.TR REAR A5 p
SIZE: A5 p*
1. MULTIPART
SET UP
1. MULTIPART
PAGE: 11 INCH
4. PAGE LENGTH
PAGE: 11 INCH
ENTER
PAGE: 11 INCH*
4. PAGE LENGTH
4.
Then specify the paepr width using #5
PAPER WIDTH on the SETUP MODE as
shown below.
4.PAGE LENGTH
WIDTH: 15 INCH*
WIDTH: 10 INCH
ENTER
5.PAPER WIDTH
WIDTH: 10 INCH*
WIDTH: 10 INCH
SAVE?: YES
5.PAPER WIDTH
ENTER
EXIT
F.TR REAR 11 x 10
SAVE?: YES
—
—
1. Setting up the printer
1-13
Download from Www.Somanuals.com. All Manuals Search And Download.
● Loading fanfold paper (Front tractor)
Fanfold paper setting procedures 3
5.
6.
Open the front cover.
Caution
Lift to release the tractor lock lever. Move
the left tractor to the triangle mark. Then
push down on the lever.
Open the front cover by
pressing both side locks
with both hands. Hold
both sides with both
hands to raise it upward
slowly. When closing
the front cover, hold
both sides with both
hands to pull it down
slowly. Press the front
cover to lock it.
In order to load
less than 5 inch
width
fanfold
paper, remove one
or two tractor
guides.
Tractor guide
Triangle mark
Release
Lock
Caution
Lock lever
Push the lock levers of
both tractors to the
LOCK positions firmly.
If the lock levers
protrude from the
tractor covers, paper
will not be fed properly,
resulting in paper
jamming.
Lock
Release
Do not put your finger under the tractor cover.
! CAUTION
—
—
1. Setting up the printer
1-14
Download from Www.Somanuals.com. All Manuals Search And Download.
● Loading fanfold paper (Front tractor)
Fanfold paper setting procedures 4
7.
Open the tractor covers on both sides. Fit
the sprocket holes on both sides of the
fanfold paper to the tractor pins. Then close
the tractor covers. Push down the lock lever
of the right tractor.
By default, paper is
fed to the 14/60
inch (approximately
when setting the paper on the tracter, Take care
not to over tighten or allow too much slack. Over
tightening deforms the guide holes and the paper may become
disconnected from the tracter during printing. Too much slack may
cause the paper to become clogged when it is inserted.
Caution
6
mm) position
from the top. This position
may be freely adjusted on
the
between 0/60 inch (0 mm)
and 63/60 inches
SETUP MODE
The TOF position can be set from 0/60 inch (0
mm). However, if this position is set to 0/60 to
Caution
(approximately 26.7 mm)
from the top of paper or the
perforation at a pitch of
1/60 inch.
9/60 inch, paper may jam, depending on the paper condition. Normally,
it is recommended that the TOF position be adjusted to the 14/60 inch
(approximately 6 mm) position from the top of the paper.
8.
Close the front cover.
Hold both sides of the front cover with both
hands and pull down the front cover slowly.
Press the front cover to lock it.
—
—
1. Setting up the printer
1-15
Download from Www.Somanuals.com. All Manuals Search And Download.
● Loading fanfold paper (Rear tractor)
Dual paper parking is available if the optional rear tractor is used. This funcion
enables two types of fanfold paper of different formats to be set together and
selected with the PAPER PATH key on the printer or by issuing a setup command
from the computer.
Paper setting procedures usig rear tarctor 1
1.
Detach the rear printer cover from the
printer.
Pull the upper
part of the rear
printer cover to
the front to
detach it from the printer.
When attaching the rear
printer cover, insert
the two legs into the
printer and then press
the rear printer cover
to lock it.
Leg
1
Leg
2.
Install the rear tractor, and plug in the
connector.
1
—
—
1. Setting up the printer
1-16
Download from Www.Somanuals.com. All Manuals Search And Download.
● Loading fanfold paper (Rear tractor)
Paper setting procedures usig rear tarctor 2
3.
Adjust the tractor guides so that they are
located at almost the same interval. Lift and
release the tractor lock levers. Move the left
tractor to the triangle mark, then push down
the lever.
In order to load
less than 8 inch
width fanfold
paper, remove
one or two tractor
guides.
1
Tractor guide
Caution
Triangle mark
Push the lock levers of
both tractors to the
LOCK positions firmly.
Release
Lock
4.
Set fanfold paper onto the rear tractor. Push
down the lock lever of the right rear tractor.
! CAUTION
Do not put your
finger under the
tractor cover.
1
—
—
1. Setting up the printer
1-17
Download from Www.Somanuals.com. All Manuals Search And Download.
● Loading fanfold paper (Rear tractor)
Paper setting procedures usig rear tarctor 3
5.
Enter the EXTENDED SETUP MODE. Select
the rear tractor on this menu so that the
printer recognizes that the rear tractor is in
use.
F.TR REAR 11 x 10
NOT INSTALL*
20. EMULATION
SET UP
OPTION: REAR Tr.
60. OPTION
ALT
OPTION: REAR Tr.
60. OPTION
EXIT
INITIAL
ENTER
INITIAL
OPTION: REAR Tr.*
F.TR REAR 11 x 10
60. OPTION
6.
7.
Press the PAPER PATH key to select REAR
Tr FRONT.
“OPEN PAPER RACK” will be displayed. Open
the paper rack.
—
—
1. Setting up the printer
1-18
Download from Www.Somanuals.com. All Manuals Search And Download.
(manual paper feeding)
● Loading cut paper
Select Manual feeding procedures 1
This section describes how to load cut sheet paper, showing an example of using
an A5 portrait form. Before loading a cut sheet, it is necessary to specify the
paper size on the SETUP MODE. Be sure to load cut sheet paper one sheet at a
1.
Check the rating of the cut sheet paper to be
used that is marked on the side of the
package.
Cut sheet paper rating marked on side of
package (Example)
Rating
A5 (Wood-Free / 70kg)
Form size
Wood-free paper Paper weight
2.
3.
Press the PAPER PAHTH key to select
MANUAL FRONT or MANUAL TOP, or MANUAL
REAR .
Specify the form size correctly on the
SETUP MODE (#4 PAGE LENGTH).
SIZE: A4 p*
SIZE: A5 p
MAN FRNT A4 p
1. MULTIPART
SET UP
1. MULTIPART
4. PAGE LENGTH
SIZE: A5 p
SAVE? : YES
4. PAGE LENGTH
ENTER
EXIT
ENTER
SIZE: A5 p *
SAVE? : YES*
MAN FRNT A5 p
4. PAGE LENGTH
—
—
1. Setting up the printer
1-19
Download from Www.Somanuals.com. All Manuals Search And Download.
(manual paper feeding)
● Loading cut paper
Select Manual feeding procedures 2
M A
N
F
R N
T
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
EJEC-
TION
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
LOAD
R
E A R
M A
N
T
O P
A
M
N
1
EJECTION
EJECTION
1
4.
Adjust the edge of the paper guide to
approximately 2 mm left of the triangle mark.
Refer to page 1-21 regarding use of the paper rack guide.
Mark
The triangle mark shows the printing start
position at the left of the printer.
—
—
1. Setting up the printer
1-20
Download from Www.Somanuals.com. All Manuals Search And Download.
(manual paper feeding)
● Loading cut paper
Select Manual feeding procedures 3
Insert a sheet of paper straight along the
5.
paper guide.
If paper is inserted at a skewed angle, the skew sensor detects
and the paper is ejected.
When using wide paper, insert
the paper using the paper
support guide attached to the
left end of the paper rack.
Insert sheets of paper one at a time along the paper
guide. Only one sheet at a time can be set on the
paper rack.
Caution
Caution
To alternate manual printing and printing with the
optional rear tractor or CSF, be sure to move the
paper guide to the left end after completion of
manual printing. Further, return the paper guide of the paper rack
to the left end. If printing is performed using the rear tractor or
CSF with the paper guide left in the manual feeding position,
paper loaded form the back will hit the paper guide, resulting in
paper jamming.
Move the Paper Guide and the Paper Support Guide to the left end.
—
—
1. Setting up the printer
1-21
Download from Www.Somanuals.com. All Manuals Search And Download.
● Printing using the cut sheet feeder (Option)
Printing procedures using CSF 1
An optional cut sheet feeder is available for this printer. The cut sheet feeder is
useful for continuous printing on cut sheets.
The paper holder of the cut sheet feeder accommodates a maximum of 150 sheets
(of 55 kg paper). Normal paper and multipart paper can be used.
1.
2.
Press the EJECT/LOAD key to move back
the fanfold paper.
Enter the EXTENDED SETUP MODE
according to the proceures shown below
and select #60 OPTION on the menu. Select
CSF (cut sheet feeder).
F.TR REAR 11 x 10
SET UP
NOT INSTALL*
20. EMULATION
60. OPTION
OPTION: CSF
ALT
OPTION: CSF
ENTER
60. OPTION
EXIT
INITIAL
INITIAL
OPTION: CSF*
F.TR REAR 11 x 10
60. OPTION
3.
Detach the rear printer cover from the
printer.
Pull the upper
part of the rear
printer cover to
the front to
detach it from the printer.
When attaching the rear
printer cover, insert the
two legs into the printer
and then press the rear
printer cover to lock it.
Leg
1
Leg
—
—
1. Setting up the printer
1-22
Download from Www.Somanuals.com. All Manuals Search And Download.
● Printing using the cut sheet feeder (Option)
Printing procedures using CSF 2
4.
Attach the hoppers and center support to
the cut sheet feeder.
Center support
Hopper
5.
Attach the cut sheet feeder to the back of
the printer.
! CAUTION
CSF
Use two hands and hold
firmly at each end when
lifting the cut sheet
feeder. Personal injury
can occur if the CSF unit
is dropped.
1
1
—
—
1. Setting up the printer
1-23
Download from Www.Somanuals.com. All Manuals Search And Download.
● Printing using the cut sheet feeder (Option)
Printing procedures using CSF 3
6.
Shuffle the paper as show below.
Be sure to shuffle sheets sufficiently before setting
them. Otherwise, several sheets of paper may be fed
at the same time resulting in a paper jam.
Caution
7.
Turn the CSF release levers to the front to
release the paper bins.
CSF release lever
—
—
1. Setting up the printer
1-24
Download from Www.Somanuals.com. All Manuals Search And Download.
● Printing using the cut sheet feeder (Option)
Printing procedures using CSF 4
8.
Turn the paper guide lock levers to the
RELEASE positions to adjust the paper
width.
Paper guide lock lever
Adjust the paper guide
to remove the gap
between the paper and
the paper guide, ensuring
that the paper does not press
too tightly against the paper
guide to avoide faulty
feeding.
Postcard changeover lever
Lock
Release
When printing on postcards,
turn this lever down.
CARD
Adjust the edge of the paper guide to
appriximately 2mm left (outside) of the
triangle mark.
Mark
1
The triangle mark shows the printing start
position at the left of the paper.
9.
Turn the paper guide lock levers to the
LOCK positions.
—
—
1. Setting up the printer
1-25
Download from Www.Somanuals.com. All Manuals Search And Download.
● Printing using the cut sheet feeder (Option)
Printing procedures using CSF 5
10.
Move the CSF release levers to the back to
fix the paper bins.
11.
Press the PAPER PATH key to select CSF
FRONT or CSF TOP.
CSF TOP A4
p
CSF FRNT A4
p
12.
Press the ENTER key to select the displayed
paper path.
—
—
1. Setting up the printer
1-26
Download from Www.Somanuals.com. All Manuals Search And Download.
● Running self-test
It is recommended that a self-test of the printer be performed before connecting
the printer to the computer. The printer can execute the self-test by itself to check
on printing quality, printing pressure, and any printer troubles.
1.
Turn on the printer power while keeping the
LINE FEED key, or LINE FEED and ONLINE
keys depressed.
After initialization, the printer enters the self-test mode and starts the
self-test.
Draft self-test printing: Turn on power while pressing the
LINE FEED key.
LQ self-test printing: Turn on power while pressing the LINE
FEED and ONLINE keys.
During printing, the ONLINE lamp blinks at an interval of 0.5 second.
The following message is displayed on the LCD.
Draft self-test printing
LQ self-test printing
“SELF TEST DRAFT”
“SELF TEST LQ”
The draft or LQ self-test prints the ASCII character in a rolling pattern.
2.
To pause the self-test, press the ONLINE
key.
To terminate the self-test, keep the ALT and
RESET keys depressed for two seconds or
more, or turn the power switch to off.
—
—
1. Setting up the printer
1-27
Download from Www.Somanuals.com. All Manuals Search And Download.
● Connecting the printer to the computer
Connecting the priter to the computer
The printer has a Centronics parallel interface and an RS-232S serial interface
as standard features.
Select the appropriate interface according to the computer and application
software to be used.
Parallel Interface
1.
Make sure that the power switch is turned to
off. Connect the signal cable to the printer
and computer.
Latches
Close the latches to secure
the connector.
13
1
25
14
2.
Specify the following parallel interface
parameters on the EXTENDED SETUP
MODE.
The printer has been set to the normal parallel
interface setting before shipment. If the default
setting does not provide proper communication,
recheck the interface setting shown below.
EXTENDED SETUP MODE
#70. INTERFACE
#71. SELECT IN ENABLE
#81. BUFFER SIZE
#82. BUSY/ACK TIMING
#83. DATA LATCH TIMING
#84. ERROR STATUS
Default setting page
Parallel
0
3-46
3-47
3-52
3-53
3-53
3-54
512 KB
TYPE 2
TYPE F.
YES
—
—
1. Setting up the printer
1-28
Download from Www.Somanuals.com. All Manuals Search And Download.
● Connecting the printer to the computer
Serial Interface
1.
Make sure that the power switch is turned to
off. Connect the signal cable to the printer
and computer.
13
1
25
14
Tighten the screws on both
sides of the connector.
2.
Specify the following serial interface
parameters on the EXTENDED SETUP
MODE.
Specify the following serial interface parameters on
the EXTENDED SETUP MODE.
EXTENDED SETUP MODE
Default setting Page
#70. INTERFACE
Parallel
0
Non
8 bits
1 bit
DTR
9600 bps
Print
No
3-46
3-47
3-47
3-48
3-48
3-49
3-49
3-50
3-50
3-51
3-51
3-52
#
#
#
#
#
#
#
#
#
#
71. SELECT IN ENABLE
72. PARITY BIT
73. DATA LENGTH
74. STOP BIT
75. PROTOCOL
76. BAUD RATE
77. SERIAL ERROR
78. CTS ENABLE
79. CD ENABLE
80. DSR ENABLE
No
No
512 KB
#81. BUFFER SIZE
—
—
1. Setting up the printer
1-29
Download from Www.Somanuals.com. All Manuals Search And Download.
● Input data hexadecimal dump
The printer can print an input data hexadecimal dump list, which contains all
input data in hexadecimal codes and corresponding ASCII characters. It is
possible to use this dump list to check whether data is being transferred in the
proper format by the computer to the printer when printing is not performed
properly.
Outputting the hexadecimal dump list
1.
Turn on the printer power while keeping the
FORM FEED key or FORM FEED and ONLINE
keys depressed.
Draft printing: Turn on power while pressing the FORM FEED key.
LQ printing:
Turn on power while pressing the FORM FEED and
ONLINE keys.
While printing the hexadecimal dump list, the following message is
displayed.
HEX DUMP
DRAFT
HEX DUMP
LQ
2.
3.
Output data from the computer to the
printer.
The printer will begin to print the hexadecimal dump list.
To stop the dump list printing, depress the
ALT and RESET keys for approximately two
seconds or turn the power switch to off.
—
—
1. Setting up the printer
1-30
Download from Www.Somanuals.com. All Manuals Search And Download.
● Link between paper path (PATH)
and paper form (MEMO)
When PATH is changed, MEMO used in a newly set PATH will be changed
automatically.
There are six types of MEMO: MEMO1 through MEMO6. Each MEMO stores
the settings of #1 to #18 on the SETUP MODE.
PAPER PATH
MEMO
MEMO
6
[ IN ]
[ OUT ]
5
MEMO
MEMO
MEMO
MEMO
4
REAR
TOP
FRONT TRACTOR
3
2
1
MANUAL
FRONT
TOP
REAR
1. MULTIPART
2. HEAD ADJUST
3. TOP ADJUST
4. PAGE LENGTH
5. PAPER WIDTH
6. TOP MARGIN
7. BOTTOM MARGIN
8. LEFT MARGIN
9. RIGHT MARGIN
10. QUALITY
REAR TRACTOR
CSF
FRONT
FRONT
TOP
11. FONT SELECT
12. CHARACTER PITCH
13. LF PITCH
14. ZOOM IN/OUT
15. PAPER FASTENER
16. PERFORATION
17. FANFOLD FEED
18. PAPER QUALITY
Link between PATH and
MEMO by default
Switching links between PATH and MEMO
1.
Press the PAPER PATH key to select the
PATH you want to use. Press the ENTER
key.
F
.
T
R
T
O
P
1
1
x
1
5
F
.
T
R
E
A
R
1
1
x
1
5
R
IN
IN
OUT
OUT
FORM
FORM
PAPER PATH
PAPER PATH
PAPER PATH
2.
Press the PAPER FORM key to select the
MEMO you want to use. Press the ENTER
key.
1
1
I
N
x
1
5
I
N
1
1
1
I
N
x
1
5
I
N
3
IN
OUT
FORM
IN
OUT
FORM
PAPER FORM
PAPER PATH
PAPER PATH
ENTER
F
.
T
R
R
E
A
R
1
1
x
1
5
IN
OUT
FORM
PAPER PATH
3.
PATH has been linked to MEMO.
Now, switching to the PATH automatically selects the MEMO linked
to it.
Changes of #1 to #17 on the SETUP MODE are reflected only in the
MEMO linked to the currently selected PATH.
—
—
1. Setting up the printer
1-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Control panel operations
2.
The liquid crystal display (LCD) on the control panel displays the processing
conditions of the printer and the settings of the functions. The keys on the control
panel provide various functions.
Control Panel
1
2
3
4
DATA
ERROR ONLINE POWER
ONLINE
TEAR OFF
1
8
RESET
2
3
PAPER FORM
PAPER PATH
9
4
5
TOF SET
EJECT/LOAD
10
FORM FEED
LINE FEED
QUALITY
SET UP
6
7
11
EXIT
EXTENDED
MICRO LF
12
13
REVERSE LF
ENTER
ALT
MICRO RLF
14
Function Keys 1
Press the TEAR OFF key, and the printer automatically feeds the
perforation of the paper to the paper cutter position (for fanfold paper
only).
If the perforation is not adjusted to the cutter position, correct the
position with the MICRO LF or MICRO RLF key. The corrected
position is saved in memory, and the perforation is fed automatically to
the paper cutter position next time.
1
TEAR OFF
TEAR OFF
RESET
(ALT + TEAR OFF keys)
2
RESET
Press the TEAR OFF key for two seconds or more while you press the
ALT key. When an "INITIAL" is displayed on the LCD, release the
keys. The printer will be reset immediately.
TEAR OFF
RESET
Even during printing, printing can be stopped immediately by resetting
the printer. When the printer is reset, it enters the busy state, the buffer
is cleared, and the printer restarts in the condition that was set on the
SETUP MODE or EXTENDED SETUP MODE (saved in the
EEPROM).
ALT
—
—
2. Control panel operations
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
G Control panel operations
Function Keys 2
Press the PAPER PATH key to change the paper path.
3
PAPER PATH
When the PAPER PATH key is pressed, the currently selected
paper path is displayed. Every press of the PAPER PATH key
alternates the LCD display as shown below.
PAPER PATH
TOF SET
♦When no options are installed
F.TR TOP
MAN FRNT
F.TR REAR
MAN REAR
MAN TOP
♦When the option rear tractors are installed
F.TR REAR
F.TR TOP
MAN FRNT
R.TR FRNT
MAN REAR
MAN TOP
♦When the optional CSF is installed
F.TR REAR
F.TR TOP
MAN FRNT
MAN TOP
CSF TOP
MAN REAR
CSF FRNT
The CSF and rear tractor cannot be used together.
LOAD
F.TR
F.TR
MAN
MAN
MAN
R.TR
CSF
EJECT
PAPER PATH
Fanfold paper: Front
Fanfold paper: Front
Rear
Top
1.
2.
3.
4.
5.
6.
7.
8.
REAR
TOP
FRNT
TOP
REAR
FRNT
FRNT
TOP
Manual: Front
Manual:Front
Manual: Front
Front
Top
Rear
Fanfold paper: Rear
Front
CSF :Rear
CSF :Rear
Front
Top
CSF
PAPER PATH Front Front Front Rear Rear
PAPER & FEED
Top
Rear Front Front Top
Fanfold paper, Push tractor
Cut sheet paper, Manual
Cut sheet paper, CSF
Standard
Option (Rear tractor or CSF)
To select the displayed paper path, press the ENTER key.
If the paper path is changed when fanfold paper or cut sheet
paper is loaded, the fanfold paper is fed back to the parking
position or the cut sheet paper is ejected.
—
—
2. Control panel operations
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
G Control panel operations
Function Keys 3
(ALT + PAPER PATH keys)
4
TOF SET
• The TOF SET key is valid only when paper is loaded. When the TOF SET
key is pressed, the current printing position is regarded as the TOF position.
• The TOF ADJUST option on the SETUP MODE specifies the position when
loading paper. The TOF SET key becomes valid after paper has been
loaded.
PAPER PATH
TOF SET
•
If the TOF position is changed when cut sheet paper is used, the changed
TOF position is valid only for the paper already loaded.
ALT
• If the EJECT/LOAD key is pressed when fanfold paper is loaded, the paper
is fed back to the parking position. When it is pressed when cut sheet paper
is loaded, the paper is ejected.
5
EJECT/LOAD
EJECT/LOAD
QUALITY
•
When the EJECT/LOAD key is pressed under the condition where fanfold
paper is at the parking position, the paper is loaded to the TOF position.
• When the EJECT/LOAD key is pressed with no paper in the manual mode,
the key is ignored. When it is pressed with paper loaded in the manual
mode, the printer ejects the paper.
• When the EJECT/LOAD key is pressed with no paper in the CSF mode, the
printer loads paper. When it is pressed with paper loaded in the CSF mode,
the printer ejects the paper.
(ALT + EJECT/LOAD keys)
6
QUALITY
Press the QUALITY key to display the currently selected printing quality on
the LCD. Continue to depress the key to display the printing qualities in the
following order.
EJECT/LOAD
QUALITY
LQ
NLQ
HQDR
DRAFT
S.S.D.
S.D.
ALT
To select the displayed printing quality, press the ENTER key.
(When in the EPSON mode)
ESC x 0
Draft is selected.
Draft
ESC x 1
LQ is selected.
LQ
Graphic speed
LCD
LQ
Normal
NLQ
Draft
HQDR
Draft
S.D.
S.S.D.
High speed 1
High speed 2
High speed 2
High speed 2
High speed 2
NLQ
LQ
LQ
S.D.
HQDR
DRAFT
S.D.
S.S.D.
S.S.D.
The #10 QUALITY menu selected from the SETUP MODE provides
the same functions as the QUALITY key. Priority is given to the last
setting. Thus, if the printing speed is changed on the menu after setting
it with the QUALITY key, the changed printing speed on the menu is
selected.
If "YES" is selected with the QUALITY LOCK option on the
EXTENDED SETUP MODE, or "S.D." or "S.S.D." is selected with the
QUALITY option on the SETUP MODE, all software commands for
changing the printing quality are ignored.
If "S.D." is selected, the draft characters are printed at 12 cpi at a speed
1.2 times as high as the normal speed. If "S.S.D." is selected, the
characters are printed at 15 cpi at a speed 1.5 times as high as the
normal speed. When "LQ" is not selected, 180/360/120/240-DPI
graphics are printed at high speed with lower bit density.
—
—
2. Control panel operations
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
G Control panel operations
Function Keys 4
The following functions are executed by pressing the corresponding
key while you press the ALT key.
7
ALT
LINE FEED
REVERSE LF
SET UP
EJECT/LOAD
PAPER PATH
TEAR OFF
MICRO LF
MICRO RLF
EXTENDED SET UP
QUALITY
TOF SET
RESET
ENTER
ALT
Press the ONLINE key to change the printing enabled (online) state and
printing disabled (offline) state.
8
9
ONLINE
ONLINE
Press the PAPER FORM key to change the format memory for the
currently selected paper path. Each press of the PAPER FORM key
changes the format memory as shown below.
Format memory 1
PAPER FORM
PAPER FORM
Format memory 2
Format memory 3
Format memory 4
Format memory 5
Format memory 6
The number of the format memory and the paper size stored in the
format memory are displayed on the LCD.
To select the displayed paper form, press the ENTER key.
Press the FORM FEED key to feed the page at the currently set page
length.
10
11
FORM FEED
FORM FEED
Press the LINE FEED key to feed the line in the forward direction at a
pitch of 1/6 inch.
LINE FEED
LINE FEED
MICRO LF
12
(ALT + LINE FEED keys)
Press the MICRO LF key to feed the line in the forward direction at a
MICRO LF
LINE FEED
pitch of 1/360 inch.
MICRO LF
ALT
13
14
Press the REVERSE LF key to feed the line in the reverse direction at a
pitch of 1/6 inch.
• Keep the key depressed for continuous reverse line feeding.
REVERSE LF
REVERSE LF
MICRO RLF
MICRO RLF
(ALT + REVERSE LF keys)
Press the MICRO RLF key to feed the line in the reverse direction at a
REVERSE LF
pitch of 1/360 inch. (Use this key to adjust the paper position.)
MICRO RLF
ALT
—
—
2. Control panel operations
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
G Control panel operations
Liquid Crystal Display
Paper Width
Orientation
(Cut sheet Paper)
(Fanfold Paper)
15 :15 inches
p : Portrait
12 :12 inches
l : Landscape
10 :10 inches
5 : 5 inches
R E A R
F . T R
1
1
.
5
x
1 5
Page Length (Fanfold Paper)
Paper Size (Cut sheet paper)
Paper Out
Paper In
: Front Tractor
REAR: Rear
TOP : Top
FRNT : Front
F. TR
R. TR
MAN
CSF
2 : 2 inches
Page
: Rear Tractor
: Manual
Length
16.5 : 16.5 inches
: Cut Sheet Feeder
A3 : A3
A4 : A4
A5 : A5
Size
LT : LETTER
Paper
HLT : HALF LETTER
LG : LEGAL
EX : EXECUTIVE
GLT : GOVERNMENT LETTER
GLG : GOVERNMENT LEGAL
LD : LEDGER
F4 : F4 SIZE
PC : POST CARD
C6 : COMMERCIAL-6
C10 : COMMERCIAL-10
MN : MONARCH
DL : DL Envelope
C5 : C5 Envelope
1 inch = 25.4 mm
Lamps
Blinks while data is transferred. Lights while data is processed except
during communication or when the input buffer contains data. Goes
out in other state.
1
DATA (Green)
2
ERROR (Amber)
ON: No paper is detected or other operational error occurs.
OFF: No error is detected.
Blinking: A functional error has occurred (such as home sense error,
internal RAM error, paper path switching error, head adjustment
error, park error and skew error).
ON: Printing is enabled.
OFF: Printing is disabled.
Blinking: The cover is open, or the printer is in the head temperature
protect mode.
3
4
ONLINE (Green)
POWER (Green)
Lights when the printer power is on. Goes out when the printer power
is turned off.
—
—
2. Control panel operations
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup options
3.
The printer has setup modes, i.e., function setting modes that are unique to this
printer. The setup modes enable various printer functions to be set up with the
function keys on the operation panel.
This section provides an the outline of the setup modes and the details of the setup
functions.
Outline of the setup modes
The setup modes consist of the SETUP MODE and EXTENDED SETUP
MODE.
The SETUP MODE is used to set the parameters that can be saved in
the format memories (memo 1 to memo 6). The EXTENDED SETUP
MODE is used to set other parameters.
Available functions in the setup modes
●The following parameters can be set in the SETUP MODE.
:
#1. MULTIPART (Printing pressure)
#2. HEAD ADJUSTMENT (Paper thickness adjustment)
#3. TOF ADJUSTMENT (Top-of-form setting)
#4. PAGE LENGTH (Page length of fanfold paper or paper size of cut sheet)
#5. PAPER WIDTH (Fanfold paper)
#6 ~ 9 Printing margin setting
.
#10. QUALITY (Printing quality)
#11. FONT SELECT (Font selection)
#12. CHARACTER PITCH (Character pitch)
#13. LF PITCH (Line feed pitch)
#14. ZOOM IN/OUT (Zooming magnification)
#15. PAPER FASTENER (Paper fastener mode setting)
#16. PERFORATION (Perforation head-up mode setting)
#17. FANFOLD FEED (Fanfold feed setting)
#18. PAPER QUALITY
#19. SELECT SAVE MEMORY (Memo 1 to memo 6)
#20. SELECT LOAD MEMORY (Memo 1 to memo 6)
●The following parameters can be set in the EXTENDED
SETUP MODE.
:
Menus #20 to #95 are used mainly to set the following
parameters:
Emulation, font, paper handling, interface, bar codes,
enlarged characters.
Entering the setup modes
●Entering the SETUP MODE
:
Press the SET UP key to enter the SETUP MODE. To
quit the SETUP MODE, press the EXIT key.
●Entering the EXTENDED SETUP MODE
:
Press the SET UP key and ALT key simultaneously to
enter the EXTENDED SETUP MODE. To quit the
EXTENDED SETUP MODE, press the EXIT key. The
printer is initialized automatically.
While data is input, the printer can enter the panel setup mode only
in the OFFLINE state.
— 3. Setup options —
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
● Operations in the setup modes
Keys used for setting
The keys shown below are used in the setup modes.
Menu selection keys
(Used with the EJECT/LOAD or
1
FORM FEED key.)
F
.
T
R
R
E
A
R
1
1
.
5
x
1
5
IN
OUT
FORM
These keys are used to change the displayed
menus. They change only the display and do not
change the setting.
PAPER PATH
The menus is changed rapidly when the
or
DATA ERROR ONLINE POWER
key is depressed and held for a second or
more.
TEAR OFF
ONLINE
RESET
PAPER PATH
PAPER FORM
FORM FEED
LINE FEED
Item selection keys
(Used with the LINE FEED or
REVERSE LF key.)
2
TOF SET
1
EJECT/LOAD
These keys are used to select items displayed
vertically in a menu. They change only the
display and do not change the setting.
QUALITY
SET UP
EXIT
2
4
3
EXTENDED
MICRO LF
REVERSE LF
ENTER
ALT
ENTER key
3
MICRO RLF
To register a displayed menu item, press the
ENTER key. When the ENTER key is
pressed, the selected item is registered in the
printer and marked with an asterisk (*), and
the menu reappears.
EXIT key
4
Press the EXIT key to exit the panel setup
mode.
— 3. Setup options —
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
● Operations in the setup modes
Setting example in the EXTENDED SETUP MODE
The following example shows how to select "OPTION: CSF" in the EXTENDED
SETUP MODE.
1.
Press SET UP key while depressing the
ALT key.
F. TR REAR 11 x 15
SET UP
ALT
20. EMULATION
2.
3.
Select #60 OPTION with the
or
key.
Press the key to display "OPTION: CSF"
on the LCD.
4.
5.
Press the ENTER key.
"CSF" is marked with an asterisk, indicating that the CSF is
selected.
Press the EXIT key. The setting is
automatically saved, and the printer is
initialized.
60. OPTION
NOT INSTALL*
OPTION: CSF
20. EMULATION
NOT INSTALL*
60. OPTION
INITIAL
60. OPTION
EXIT
OPTION: CSF
ENTER
F. TR REAR 11 x 15
INITIAL
OPTION: CSF *
60. OPTION
In the SETUP MODE, after pressing the EXIT key select SAVE
YES by the or key and press the ENTER key. If SAVE
NO is selected, any changes made in the SETUP MODE are
erased when the printer power is turned off.
— 3. Setup options —
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup mode summary
(1)
●
The astarisk (*) indicates
the factory default setting.
SETUP MODE
1
2
3
4
TOF
ADJUSTMENT
HEAD
ADJUSTMENT
PAGE
LENGTH
REGULAR SIZE
MULTIPART
A3 p
A3 l
LEDGER p
F4 p
COM-6 l
COM-10 p
COM-10 l
MONARCH p
MONARCH l
DL p
DL l
C5 p
C5 l
INCH SIZE
TOP OF FORM
n/60 INCH
AUTO: n CLICK
2
NORMAL*
DARK 1
DARK 2
AUTO
7
12
12.5
13
13.5
14
14.5
15
15.5
16
16.5
A4 p *
F4 l
-2 ≤ n ≤ 5
2.5
3
7.5
8
A4 l
A5 p
A5 l
LETTER p
LETTER l
H.LETTER p
H.LETTER l
LEGAL p
LEGAL l
EXECUTIVE p
EXECUTIVE l
G.LETTER p
G.LETTER l
G.LEGAL p
G.LEGAL l
POST CARD p
POST CARD l
COM-6 p
+
0 ≤ n ≤ 63
FIX : n CLICK
3.5
4
8.5
9
n=14*
-5 ≤ n ≤ 25
4.5
5
9.5
10
AUTO
0
CLICK*
5.5
6
6.5
10.5
11 *
11.5
5
12
11
6
7
8
9
10
PAPER WIDTH
(INCH SIZE)
BOTTOM
MARGIN
RIGHT
MARGIN
CHARACTER
PITCH
FONT SELECT
TOP MARGIN
LEFT MARGIN
QUALITY
ROMAN *
SANS SERIF
COURIER
PRESTIGE
SCRIPT
10 CPI *
12 CPI
15 CPI
16.7 CPI
17.1 CPI
20 CPI
+ n LINE
0 ≤ n ≤ 15
n=0*
+ n LINE
0 ≤ n ≤ 15
n=0*
+ n COLUMN
0 ≤ n ≤ 63
n=0*
+ n COLUMN LQ *
15 INCH *
12 INCH
10 INCH
5 INCH
0 ≤ n ≤ 63
n=0*
NLQ
HQDR
DRAFT
S.D.
OCR-B
S.S.D.
OCR-A
24 CPI
GOTHIC
ORATOR
ORATOR-S
PROPORTIONAL
13
14
15
16
20
17
18
19
SELECT LOAD
MEMORY
PAPER
FASTENER
PERFORA-
TION
FANFOLD
FEED
PAPER
QUALITY
SELECT SAVE
MEMORY
LF PITCH
ZOOM IN/OUT
HEAD LIFT
UP
FASTENER
FRICTION
66 %
79 %
83 %
91 %
100 %*
116 %
120 %
141 %
200 %
400 %
600 %
800 %
1000%
1200 %
1400 %
1600 %
6 LPI *
8 LPI
9 LPI
3 LPI
4 LPI
MEMO 1
MEMO 2
MEMO 3
MEMO 4
MEMO 5
MEMO 6
MEMO 1
MEMO 2
MEMO 3
MEMO 4
MEMO 5
MEMO 6
YES
NO *
YES
YES *
NO
GOOD
NO GOOD*
NO *
EXTENDED SETUP MODE
20
21
22
23
26
24
25
CHARACTER
TABLE (HP)
CHARACTER
TABLE(EPSON)
CHARACTER
TABLE(IBM)
NATIONAL
FONT
AGM
(IBM)
EMULATION
CODE PAGE
437 *
850
857
858
860
ROMAN-8 *
NORWAY 1
NORWAY 2
IRV
CHAR. SET 1*
CHAR. SET 2
ITALIC *
GRAPHIC
DOWNLOAD
CODE PAGE
USA *
JAPAN
EPSON *
IBM
HP
NO *
YES
CODE PAGE
PC-8 DEN/NOR
LEGAL
FRANCE
GERMANY
U.K.
DENMARK
SWEDEN
ITALY
NORWAY
DENMARK2
SPAIN2
LATIN AMERICA
KOREA
ITALY
SWEDEN 1
SWEDEN 2
FRANCE 2
GERMAN 2
SPAIN 2
SPAIN 3
JAPAN
861
SPAIN
1
863
865
BRASCII
ABICOMP
ISO8859-1
FRANCE
GERMAN
U.K.
1
1
TURKEY
LEGAL
SPAIN
PORTGAL
1
PORTGAL 2
27
28
29
30
31
32
33
34
PAGE LENGTH
LOCK
TABULATION
ACCENT CHR
ZERO STYLE
CR SETTING
LF SETTING
FONT LOCK
PITCH LOCK
2CHAR.
NO-SLASHED *
SLASHED
SIMPLE*
COMPO.
CR ONLY *
CR + LF
AUTOFEED
LF ONLY
LF+CR *
NO *
YES
NO *
YES
NO *
YES
4 CHAR.
6 CHAR.
8 CHAR. *
10 CHAR.
12 CHAR.
— 3. Setup options —
3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
● Setup mode summary(2)
EXTENDED SETUP MODE
35
36
37
38
40
41
BARCODE/
ENLARGED CHAR
QUALITY
LOCK
CHR TBL
LOCK
FF CODE
AT TOF
GRAPHIC
QUALITY
BARCODE
TYPE
CODE39 *
CODE93
CODE128
EAN8
EAN13
UPC-A
INDSTRIAL 2OF5
INTERLEAVED 2OF5
MATRIX 2OF5
CODABAR
NO *
YES
NO *
YES
YES *
NO
MODE 1
MODE 2 *
MODE 3
MODE 1 *
MODE 2
IGNORED
UPC-E
POSTNET
ELEMENT
CODE11
43
44
50
51
60
61
42
SOFTWARE
SETUP
LARGE
CHAR. SIZE
BARCODE
SIZE
OPTION
PAPER PATH
PCL MODE
CHR TB2 HP
VALID *
IGNORED 1
IGNORED 2
PCL3 + *
PCL3
PCL3 + D
LINE-DRAW *
MATH-7
NOT INSTALLED *
CSF
REAR TRACTOR
F.TR. ->REAR *
F.TR. ->TOP
SIZE: 1
SIZE: 2
SIZE: 4
SIZE: 8 *
SIZE: 12
SIZE: 16
SIZE: 24
SIZE: 32
SIZE: 1 *
SIZE: 1.5
SIZE: 2
MANUAL->FRONT
MANUAL->TOP
MANUAL->REAR
R.TR.->FRONT
CSF->FRONT
SIZE: 2.5
CSF->TOP
63
64
65
66
67
62
PAPER JAM
DETECTION
SKEW
DETECTION
P.OUT
DETECTION
AUTO SCROLL
POSITION
LF SPEED
AUTO SCROLL
NO SCROLL *
0.5 SEC
1 SEC
YES *
NO
YES *
NO
NORMAL *
1/2
1/3
ANY POS *
TOF ONLY
YES *
NO
5 SEC
10 SEC
15 SEC
76
70
71
72
75
73
74
SELECT IN
ENABLE
BAUD RATE
DATA LENGTH
PARITY BIT
PROTOCOL
STOP BIT
INTERFACE
38400 BPS
19200 BPS
9600 BPS*
4800 BPS
2400 BPS
1200 BPS
600 BPS
8 BITS*
7 BITS
NON *
EVEN
ODD
1 BIT *
2 BITS
DTR*
1
0*
I/F
PARALLEL *
SERIAL
AUTO
XON/XOFF 1
XON/XOFF 2
ETX/ACK
300 BPS
77
78
79
80
81
83
82
BUSY/ACK
TIMING
DATA LATCH
TIMING
CTS ENABLE
CD ENABLE
SERIAL ERROR
BUFFER SIZE
DSR ENABLE
NO *
YES
NO *
YES
NO *
YES
TYPE F. *
TYPE R.
PRINT "*" *
IGNORED
512KB*
8KB
128B
TYPE 1
TYPE 2 *
TYPE 3
94
95
91
92
93
84
90
SETUP MENU
LIST
ERROR
STATUS
PRINT
DIRECTION
KEY
LOCK
DISPLAY
LANGUAGE
RESET KEY
LOCK
SLEEP MODE
YES *
NO
PRE-DIRECTION
UNI-DIRECTION
BI-DIRECTION *
YES *
NO
PATH & FORM
EXTEND
ALL SETUP
ENGLISH *
NO *
YES
NO *
YES
DEUTSCH
FRANCAIS
ESPANOL
ITALIANO
— 3. Setup options —
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
● Factory default setting
Factory Default Setting
●●NORMAL
Page
3-8
3-9
Printing
#01 : MULTIPART
#02 : HEAD ADJUSTMENT
#15 : PAPER FASTENER
#16 : PERFORATION
#17 : FANFOLD FEED
#18 : PAPER QUALITY
#66 : LF SPEED
●●AUTO 0 CLICK
NO 3-22
NO 3-22
YES 3-23
NOT GOOD 3-23
NORMAL 3-44
Form selection
#61 : PAPER PATH
●●F.Tr.->REAR
3-40
Character
#10 : QUALITY
●●LQ
●●ROMAN
●●10CPI
●●ROMAN-8
●●ITALIC
3-17
3-18
3-19
3-25
3-26
3-26
3-27
3-28
3-28
3-30
3-30
3-35
3-41
#11 : FONT SELECT
#12 : CHARACTER PITCH
a
a
#21 : CHARACTER TABLE (HP)
#22 : CHARACTER TABLE (EPSON)
#23 : CHARACTER TABLE (IBM)
#24 : NATIONAL FONT (EPSON)
#25 : CODE PAGE
#26 : AGM (Alternate Graphics Mode) (IBM)
#29 : ACCENT CHR
#30 : ZERO STYLE
#38 : GRAPHIC QUALITY
#51 : CHRACTER TABLE 2 (HP)
●●SET 1
●●U.S.A.
●●437
●●NO
●●SIMPLE
●●NO SLASHED
●●MODE2
●●LINE DRAW
Zooming
#14 : ZOOM IN/OUT
●●100% 3-21
Printing start position and printing area
inch
#03 : TOF ADJUSTMENT
●●14/60
3-10
3-11
3-12
3-13
3-14
3-15
3-16
(Memo
inch Memo
4
#04 : PAGE LENGTH ●●
#05 : PAPER WIDTH ●●(
1
~
~
3)11
(
~
~
6)A4 p
inch
6)10
●●0 LINE
●●0 LINE
●●0 COL
●●0 COL
Memo
inch Memo
1
3)15
(
4
#06 : TOP MARGIN
#07 : BOTTOM MARGIN
#08 : LEFT MARGIN
#09 : RIGHT MARGIN
Line feed and carriage return
#13 : LF PITCH
●●6 LPI
●●CR ONLY
●●LF + CR
3-20
3-29
3-29
3-31
3-34
3-55
#27 : CR SETTING
#28 : LF SETTING
#31 : TABULATION
#37 : FF CODE AT TOF
#90 : PRINT DIRECTION
●●8 CHAR
●●YES
●●BI-DIRECTION
— 3. Setup options —
3-6
Download from Www.Somanuals.com. All Manuals Search And Download.
● Factory default setting
Lock function
Factory Default Setting
●●NO
Page
#32 : PAGE LENGTH LOCK
#33 : FONT LOCK
#34 : PITCH LOCK
#35 : QUALITY LOCK
#36 : CHARACTER TABLE LOCK
#92 : KEY LOCK
3-31
3-32
3-32
3-33
3-33
3-56
3-56
●●NO
●●NO
●●NO
●●NO
●●NO
●●NO
#93 : RESET KEY LOCK
Bar code and enlarged character
#40 : BARCODE/ENLARGED CHARACTER
#41 : BARCODE TYPE
●●MODE 1
●●CODE 39
3-36
3-37
#42 : BARCODE SIZE
#43 : ENLARGED CHARACTER SIZE
●●1 3-39
●●8 3-39
Operation condition
#19 : SELECT SAVE MEMORY
#20 : SELECT LOAD MEMORY
#20 : EMULATION
●●MEMO 1
3-24
3-24
3-25
3-40
3-40
3-41
3-42
3-43
3-43
3-44
3-45
3-55
3-57
3-57
●●MEMO 1
●●EPSON
●●VALID
#44 : SETUP COMMAND
#50 : PCL MODE (HP)
#60 : OPTION
#62 : AUTO SCROLL
#63 : P.OUT DETECTION
#64 : SKEW DETECTION
#65 : PAPER JAM
#67 : AUTO SCROLL POSITION
#91 : DISPLAY LANGUAGE
#94 : SLEEP MODE
●●PCL 3+
●●NOT INSTALL
●●NO SCROLL
●●YES
●●YES
●●YES
●●ANY POS
●●ENGLISH
●●YES
#95 : SETUP MENU LIST
●●PATH & FORM
Interface condition
#70 : INTERFACE
●●PARALLEL
3-46
#71 : SELECT IN ENABLE
●●0 3-47
#72 : PARITY BIT (SERIAL I/F)
#73 : DATA LENGTH (SERIAL I/F)
#74 : STOP BIT (SERIAL I/F)
#75 : PROTOCOL (SERIAL I/F)
#76 : BAUD RATE (SERIAL I/F)
#77 : SERIAL ERROR (SERIAL I/F)
#78 : CTS ENABLE (SERIAL I/F)
#79 : CD ENABLE (SERIAL I/F)
#80 : DSR ENABLE (SERIAL I/F)
#81 : BUFFER SIZE
●●NON
3-47
3-48
3-48
3-49
3-49
3-50
3-50
3-51
3-51
3-52
3-53
3-53
3-54
●●8 BITS
●●1 BIT
●●DTR
●●9600 B
●●PRINT
●●NO
●●NO
●●NO
●●64KB
●●TYPE 2
●●TYPE F.
●●YES
#82 : BUSY/ACK TIMING (PARALLEL I/F)
#83 : DATA LATCH TIMING (PARALLEL I/F)
#84 : ERROR STATUS (PARALLEL I/F)
— 3. Setup options —
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Multipart
Function
This function improves the printing capability on
multipart paper.
Use multipart paper consisting of an original plus eight non-
carbon sheets or copying paper up to 0.59 mm thick.
#01
Setting procedures
1 MULTIPART
COPY: NORMAL
COPY: DARK 1
COPY: DARK 2
COPY: AUTO
Supplementary notes
Printing capabilities on multipart paper are selectable as shown below.
LCD display
NORMAL
DARK1
LQ
Draft
ORIGINAL + 5
ORIGINAL + 7
ORIGINAL + 8
ORIGINAL + 4
ORIGINAL + 7
ORIGINAL + 8
DARK1
AUTO
Automatically swiches Normal, Dark 1, or Dark 2 according
to the paper thickness.
— 3. Setup options —
3-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Head adjustment
Function
This function adjusts the gap between the print head
and platen.
This function has FIX and AUTO modes: The gap is fixed in the
FIX mode, and the gap is automatically adjusted in the AUTO
mode.
#02
Setting procedures
2
HEAD ADJUST
AUTO :
n
CLICK
DEFAULT : AUTO : 0 CLICK
-2 < n < +5
The smaller the number, the
smaller the gap between the
head and platen.
FIX :
n
CLICK
-5 < n < +25
Supplementary notes
Every click changes the gap by 0.04 mm.
The recommended gap for 70 kg 1P paper is at the 0 click
position in the FIX mode.
●AUTO mode
In the AUTO mode, the gap between the print head and
platen is automatically adjusted according to the paper
thickness. Since the most appropriate gap differs with the
type of paper, select the proper position between -2 and +5
according to the printing results.
●FIX mode
The gap between the print head and platen is fixed as
specified.
Select the proper position according to the paper type and
thickness by referring to the table below.
In the AUTO mode,
the gap is
automatically
adjusted every time
fanfold paper or
Paper type/fixed click position
-1~1 1~3 3~5 5~7 7~9 9~11 11~13 13~15 15~17
Cut
sheet
Ream weight: 55 to 90 kg
Ream weight: 90 to 135 kg
Ream weight: 180 kg
Postcard
manually-inserted paper is
loaded. When CSF is used,
automatic paper thickness
adjustment is performed
when the paper is first
loaded. Thereafter,
automatic paper thickness
adjustment is performed
when the next sheet is fed
if printing is not performed
within 3 to 4 seconds after
the paper is ejected.
Multipart
paper
2sheets
3sheets
4sheets
5sheets
6sheets
7sheets
8sheets
9sheets
(Paper
weight
: 34 kg)
0.08 0.16 0.24 0.32 0.4 0.48 0.56 0.64 0.72
0.16 0.24 0.32 0.4 0.48 0.56 0.64 0.72 0.8
Total paper thickness (mm)
— 3. Setup options —
3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
TOF adjustment
Function
This function specifies the top of form (TOF)
position.
When paper is loaded, the printer detects the end of the paper and
determines the printing start position based on the detected paper
end. That position is the top of the form (TOF).
#03
Setting procedures
3
TOF ADJUST
TOP: + n /60 IN
The value may be changed with the
and
keys.
0
≤ n ≤ 63
DEFAULT : n=14
Supplementary notes
The TOF position is adjusted in units of 1/60 inch. It can be
adjusted between 0/60 inch (minimum) and 63/60 inches
(maximum) from the end of paper.
Though the TOF position can be set from 0/60
Caution
inch (0 mm), paper may jam if it is set to a
value between 0/60 inch to 9/60 inch. Normally, it is
recommended that the TOF position be set to 14/60 inch
(approximately 6 mm) from the paper end.
— 3. Setup options —
3-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Page length
Function
This function specifies the page length of the form
to be used.
Thirty types of page lengths, from 2 to 16.5 inches in 0.5 inch steps,
plus seventeen standard sizes are available as shown below.
#04
Setting procedures
4
PAGE LENGTH
SIZE: EXECUT p
SIZE: EXECUT l
PAGE: 12.5 IN
PAGE: 13 IN
PAGE: 13.5IN
PAGE: 14 IN
PAGE: 14.5 IN
PAGE: 15 IN
PAGE: 15.5 IN
PAGE: 2 IN
PAGE: 2.5 IN
PAGE: 3 IN
PAGE: 3.5 IN
PAGE: 4 IN
PAGE: 4.5 IN
PAGE: 5 IN
SIZE: G.LETTER p
SIZE: G.LETTER l
SIZE: G.LEGAL p
SIZE: G.LEGAL l
SIZE: LEDGER p
SIZE: F4 p
PAGE: 5.5 IN
PAGE: 6 IN
PAGE: 6.5 IN
PAGE: 7 IN
PAGE: 7.5 IN
PAGE: 8 IN
PAGE: 8.5 IN
PAGE: 9 IN
PAGE: 9.5 IN
PAGE: 10 IN
PAGE: 10.5 IN
PAGE: 11 IN
PAGE: 11.5 IN
PAGE: 12 IN
PAGE: 16 IN
SIZE: F4 l
PAGE: 16.5 IN
SIZE: POST C. p
SIZE: POST C. l
SIZE:
SIZE:
SIZE:
SIZE:
SIZE:
SIZE:
A3 p
A3 l
A4 p
A4 l
A5 p
A5 l
SIZE: COM-6 p
SIZE: COM-6 l
SIZE: COM-10 p
SIZE: COM-10 l
SIZE: LETTER p
SIZE: LETTER l
SIZE: H.LETTER p
SIZE: H.LETTER l
SIZE: LEGAL p
SIZE: LEGAL l
SIZE: MONARCH p
SIZE: MONARCH l
SIZE: DL p
If the PAGE LENGTH
LOCK option is set to
NO in the EXTENDED
SETUP MODE, the
page length can be
changed by a software
command. The values
available on the menu
serve as the default
values. If the PAGE
SIZE: DL l
SIZE: C5 p
SIZE: C5 l
LENGTH LOCK option Supplementary notes
is set to YES in the
EXTENDED SETUP
When fanfold paper is used, the page length set here is used to define
the perforation.
MODE, any software
command to change the
page length is ignored.
The printer loads paper, it regards the end of the paper as the
perforation. The TOF (top-of-form) position is determined from the
end of the paper based on a preset TOF value.
— 3. Setup options —
3-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Paper width
Function
This function specifies the width of fanfold paper.
This function specifies the width of fanfold paper in inches.
#05
Setting procedures
5 PAPER WIDTH
WIDTH : 15 IN
WIDTH : 12 IN
WIDTH : 10 IN
WIDTH : 5 IN
Supplementary notes
The following table shows the relationship between the paper width
settings in inches and the number of columns printable on each line,
when characters are printed at 10 cpi.
Display
Paper width
Max. columns/line
15 IN
12 IN
10 IN
5 IN
15 inches
12 inches
10 inches
5 inches
136
106
80
36
— 3. Setup options —
3-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Top margin
Function
This function specifies the length of the area at the top
of the paper where printing is disabled in units of 6 LPI
from the TOF position.
#06
Setting procedures
6 TOP MARGIN
T.M. :
T.M. :
0
LINE
n = 0 ~ 15
15 LINE
Supplementary notes
The top margin is specified in units of 6 LPI (lines per inch)
within the range from 0 (minimum) to 15 (maximum) from the
TOF position.
0/60 to 63/60 inches
0/60 to 63/60 inches
(#3TOF ADJUSTMENTonSETUP MENU)
(#3 TOF ADJUSTMENT on SETUP MENU)
0 to 15 lines
0 to 15 lines
(#6TOP MARGINonSETUPMENU)
(#6 TOPMARGINon SETUP MENU)
TOF
TOF
TOF
Printable area when top
margin is specified.
Printable area when top
margin is specified.
Printable area when top
margin is specified.
— 3. Setup options —
3-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Bottom margin
Function
This function specifies the length of the area at the
bottom of the paper where printing is disabled in units
of 6 LPI from the TOF position of the following page.
#07
Setting procedures
7 BOTTOM MARGIN
B.M. : 0 LINE
n = 0 ~ 15
B.M. : 15 LINE
Supplementary notes
The bottom margin of fanfold paper is specified in units of 6
LPI (lines per inch) within the range from 0 to 15 from the
TOF position of the following page.
The bottom margin of cut sheet paper is specified within the
range from 0 to 15 from the bottom of the printable area.
0/60 to 63/60 inches
0 to 15 lines
(#3 TOF ADJUSTMENT on SETUP MENU)
(#7 BOTTOM MARGIN on SETUP MENU)
TOF
Printable area when
bottom margin is
specified.
TOF
Printable area when
bottom margin is specified.
Printable area when
bottom margin is
TOF
specified.
0 to 15 lines
(#7 BOTTOM MARGIN on SETUP MENU)
4 mm
— 3. Setup options —
3-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Left margin
Function
This function specifies the length of the area on the left
side of the paper where printing is disabled from the
left end of the printable area.
#08
Setting procedures
8 LEFT MARGIN
L.M. :
L.M. :
0
COL
n = 0 ~ 63
63 COL
Supplementary notes
The left margin is specified by the number of columns (1/10")
within the range from 0 to 63 columns from the left end of the
printable area as shown below.
Left end of printable area
0 to 63 characters
Left end of printable area
0 to 63 characters
(#8 LEFT MARGIN on SETUP
MENU)
(#8 LEFT MARGIN on SETUP MENU)
Printable area
when left margin
is specified.
Printable area
when left margin
is specified.
Printable area
when left margin
is specified.
— 3. Setup options —
3-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Right margin
Function
This function specifies the length of the area on the
right side of the paper where printing is disabled from
the right end of the printable area.
#09
Setting procedures
9 RIGHT MARGIN
R.M. : 0 COL
n = 0 ~ 63
R.M. : 63 COL
Supplementary notes
The right margin by specified in the number of columns
(1/10") within the range from 0 to 63 from the right end of the
printable area as shown below.
Right end of printable area
0 to 63 characters
Right end of printable area
0 to 63 characters
(#9 RIGHT MARGIN on SETUP
MENU)
(#9 RIGHT MARGIN on SETUP
MENU)
Printable area
when right
margin
is specified.
Printable area
when right margin
is specified.
Printable area
when right
margin
is specified.
— 3. Setup options —
3-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Character quality
Function
This function specifies character quality.
#10
Setting procedures
10 QUALITY
QLTY:
QLTY:
QLTY:
LQ
NLQ
HQDR
QLTY:
QLTY:
QLTY:
DRAFT
S.D.
S.S.D
Supplementary notes
This option has the same function as the QUALITY key (i.e.,
EJECT/LOAD key while depressing ALT key). Priority is given to
the most recent setting made with the QUALITY key or in the
SETUP MODE.
When "LQ" is not selected, 180/36/120/240-dpi graphics are
printed at high speed with lower bit density.
QUALITY
LQ
Graphic speed
Normal
NLQ
High speed 1
High speed 2
High speed 2
High speed 2
High speed 2
HQDR
DRAFT
S. D.
S. S. D.
— 3. Setup options —
3-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Character font
Function
This function specifies the typeface of the font
characters.
The following ten fonts are available: Roman, Sans Serif,
Courier, Prestige, Script, OCR-B, OCR-A, Gothic, Orator, and
Orator-s.
#11
Setting procedures
11 FONT SELECT
FONT : ROMAN
FONT : S. SERIF
FONT : COURIER
FONT : PRESTIGE
FONT : SCRIPT
FONT : OCR-B
FONT : OCR-A
FONT : GOTHIC
FONT : ORATOR
FONT : ORATORs
Supplementary notes
If the FONT LOCK option is set to NO in the EXTENDED
SETUP MODE, the font can be changed by a software
command. The font selected on the menu serves as the
default font.
If the FONT LOCK option is set to YES in the EXTENDED
SETUP MODE, the currently selected font cannot be
changed by a software command.
Font
Printing sample
ROMAN
SANS SERIF
COURIER
PRESTIGE
SCRIPT
OCR-B
OCR-A
GOTHIC
ORATOR
ORATOR-S
— 3. Setup options —
3-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Character pitch
Function
This function specifies the character pitch.
The available pitches are: 10 cpi, 12 cpi, 15 cpi, 16,7 cpi, 17.1 cpi,
20 cpi, 24 cpi, and proportional.
#12
Setting procedures
12 CHARACTER PICH
PITCH :
PITCH :
PITCH :
PITCH :
10 CPI
12 CPI
15 CPI
16.7 CPI
PITCH :
PITCH :
PITCH :
PITCH :
17.1 CPI
20 CPI
24CPI
PROP.
Supplementary notes
If the PITCH LOCK option is set to NO in the EXTENDED SETUP
MODE, the character pitch can be changed by a software
command. The pitch selected on the menu serves as the default
pitch.
If the PITCH LOCK option is set to YES in the EXTENDED SETUP
MODE, the currently selected pitch cannot be changed by a
software command.
Character pitch
Printing sample
10 cpi
12 cpi
15 cpi
16.7 cpi
17.1 cpi
20 cpi
24 cpi
LQ Proprtional
— 3. Setup options —
3-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Line feed pitch
Function
This function specifies the line feed pitch as shown
below.
LF: 6 LPI...... 1/6 inch pitch
LF: 8 LPI...... 1/8 inch pitch
LF: 9 LPI...... 1/9 inch pitch
LF: 3 LPI...... 1/3 inch pitch
LF: 4 LPI...... 1/4 inch pitch
(LPI = Line Per Inch)
#13
Setting procedures
13 LF PITCH
LF:
LF:
6 LPI
8 LPI
LF:
LF:
3 LPI
4 LPI
LF:
9 LPI
— 3. Setup options —
3-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Enlarging/Reducing print
Function
This function specifies the magnification enlargement
(zoom in) or reduction (zoom out).
It can enlarge or reduce data as needed according to the form size.
It is used, for example, to print documents prepared for the A4
paper on A3 paper.
#14
Setting procedures
14 ZOOM IN/OUT
ZOOM IN:
800
%
%
ZOOM OUT: 66
ZOOM OUT: 79
ZOOM OUT: 83
ZOOM OUT: 91
%
%
%
%
%
%
ZOOM IN:
ZOOM IN:
ZOOM IN:
ZOOM IN:
ZOOM IN:
120
141
200
400
600
%
%
%
%
ZOOM IN: 1000
ZOOM IN: 1200
ZOOM IN: 1400
%
%
ZOOM IN: 1600
%
NO ZOOM:
ZOOM IN :
100
116
%
Supplementary notes
Documents are enlarged or reduced vertically and
horizontally by the degree of magnification specified with this
function. The following shows the frequently-used
magnifications for reference.
(Reduction)
ZOOM OUT
66%
83%
A3 A4
A4 EXECUTIVE
(Enlargement)
ZOOM IN
116%
141%
EXECUTIVE(p) A4(p)
(P) : Portrait
A4(p) A3(p)
The magnification displayed on the LCD has some
allowance. (Ep)nlarged or reduced characters are printed in a
different font from the specified font.
— 3. Setup options —
3-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Paper fastener mode setting
Function
This function sets the mode for stable paper feeding with
multipart fanfold paper bound by paper fasteners.
When the multipart fanfold paper is bound by paper fasteners or
paper staples rather than glue, paper slippage or paper jam error
may occur. When paper is fed while the print head is stopped on a
paper fastener, the fastener will become a load and normal paper
feeding will be disabled. When YES is selected, the print head does
not stop on a paper fastener.
#15
Setting procedures
15 PAPER FASTENER
FASTENER MODE : YES
FASTENER MODE : NO
Perforation head-up mode setting
Function
This setting is effective when the perforation peak exceeds the
range which permits normal paper feeding.
When the perforation peak of the paper which is spread on a flat
surface is 1.0 mm or more, paper slippage or paper jam error may
occur. This will result in a stress when the printi head passes over
the perforation, and normal paper feeding will be disabled.
When YES is selected, the gap between the print head and the
platen is widen while the paper is feeding within 0.5 inch of the
perforation.
#16
Setting procedures
16 PERFORATION
HEAD LIFT UP : YES
HEAD LIFT UP : NO
— 3. Setup options —
3-22
Download from Www.Somanuals.com. All Manuals Search And Download.
Fanfold feed setting
Function
This setting specifies whether or not to also use the friction
rollers when feeding fanfold paper.
When multipart forms are used, the friction rollers should be set to
be used (FRICTION: YES). When the thin single fanfold paper is
used, the friction rollers should be set to be not used (FRICTION:
NO).
#17
Setting procedures
17 FANFOLD FEED
FRICTION : YES
FRICTION : NO
Supplementary notes
When the binding method of a multipart form is different on
the left and right sides, the friction rollers should be set to be
not used (FRICTION: NO).
Selection of paper quality
Function
The paper quality is selected.
Select the paper quality according to the condition of the paper
edge.
When the paper edge is bent or curled over after printing, select
"Paper quality : Bad". In this case, after inserting the paper, it is
necessary to straighten the paper edge.
#18
Setting procedures
18 PAPER QUALITY
QUALITY : GOOD
QUALITY : NO GOOD
— 3. Setup options —
3-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Saving data in format memory
Function
This function writes the data of the format memory
currently in use to the specified memo.
#19
Setting procedures
19 SAVE MEMO
SAVE : MEMO 1
SAVE : MEMO 2
SAVE : MEMO 3
SAVE : MEMO 4
SAVE : MEMO 5
SAVE : MEMO 6
Supplementary notes
Format memory
The format memory saves six setup parameters. Optional
setup parameters can be saved in the memory and
loaded on the printer. If different formats are specified
and saved in the memory, you can change setup
parameters by using the format memory.
Loading data from format memory
Function
This function reads data from the specified format
memory into the format memory currently in use.
The user can exchange data in the format memory with data in any of
the following memos: memo 1 to memo 6.
#20
Setting procedures
20 LOAD MEMO
LOAD : MEMO 4
LOAD : MEMO 5
LOAD : MEMO 6
LOAD : MEMO 1
LOAD : MEMO 2
LOAD : MEMO 3
— 3. Setup options —
3-24
Download from Www.Somanuals.com. All Manuals Search And Download.
Emulation
Function
The printer has three types of emulations shown below.
TM
Emulation compatible with the EPSON LQ-2550
Emulation compatible with the IBM 2391™
#20
Emulation compatible with the Hewlett Packard
TM
TM
Rugged Writer 480 (PCL3)
Setting procedures
20 EMULATION
EML :
EML :
EML :
EPSON
IBM
Selecting emulation EPSON
Selecting emulation IBM
Selecting emulation HP
HP
Character table (HP)
Function
This function specifies the character table used in the
HP mode.
#21
Setting procedures
21 CHR TB HP
TBL : NORWAY 1
TBL : NORWAY 2
TBL : IRV
TBL : ROMAN-8
TBL : CODE PG
TBL : PC-8D/N
TBL : LEGAL
TBL : SWEDEN 1
TBL : SWEDEN 2
TBL : SPAIN 1
TBL : FRANC 1
TBL : GERMN 1
TBL : U. K.
TBL : ITALY
TBL : FRANC 2
TBL : GERMN 2
TBL : SPAIN 2
TBL : SPAIN 3
TBL : JAPAN
TBL : PORTU 2
TBL : PORTU 1
— 3. Setup options —
3-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Character table (EPSON)
Function
This function specifies the character table used in the
EPSON mode.
#22
Setting procedures
22 CHR TB EPSON
TBL : ITALIC
TBL : GRAPHIC
TBL : DOWN LD
TBL : CODE PG
Supplementary notes
The values specified here serve as the default values.
ITALIC
GRAPHIC
DOWN LD
CODE PG
Italic table
Extended graphic table
Download table
Code page
Character table (IBM)
Function
This function specifies the character table used in the
IBM mode.
#23
Setting procedures
23 CHR TB IBM
TBL: SET 1
TBL: SET 2
Supplementary notes
SET1
SET2
Character set 1
Character set 2
— 3. Setup options —
3-26
Download from Www.Somanuals.com. All Manuals Search And Download.
National font (EPSON)
Function
The printer has sixteen national fonts as shown below:
U.S.A., France, Germany, U.K., Denmark, Sweden, Italy, Spain, Japan,
Norway, Denmark 2, Spain 2, Latin America, Korea, Turkey, and Legal
#24
Setting procedures
24 NATIONAL FONT
CNTRY: USA
CNTRY: ITALY
CNTRY: SPAIN
CNTRY: JAPAN
CNTRY: NORWAY
CNTRY: DNMRK 2
CNTRY: SPAIN 2
CNTRY: LATN AM
CNTRY: KOREA
CNTRY: TURKEY
CNTRY: LEGAL
CNTRY: FRANCE
CNTRY: GERMANY
CNTRY: U.K.
CNTRY: DENMRK
CNTRY: SWEDEN
Supplementary notes
These national fonts are not applicable to the IBM or HP mode.
The following table shows the national fonts.
23
24
40
5B
5C
5D
5E
60
7B
7C
7D 7E
U.S.A.
France
Germany
U.K.
Denmark
Sweden
Italy
Spain
Japan
Norway
2
Denmark
2
Spain
Latin America
Korea
Turkey
Legal
If some specific characters are printed in a font of another
nation, the code page or national font may be specified
improperly. Refer to the manual of the computer or
application software used. Use great care with software
produced in other countries.
— 3. Setup options —
3-27
Download from Www.Somanuals.com. All Manuals Search And Download.
Code page
Function
The printer has eleven code pages shown below:
(1) Code page 437: U.S.A.
(2) Code page 850: Multilingual
(3) Code page 857: Turkey
(4) Code page 858: Multilingual (EURO symbol)
(5) Code page 860: Portugal
(6) Code page 861: Icelandic
(7) Code page 863: Canadian-French
(8) Code page 865: Norway
(9) Code page Brascii
(10) Code page Abicomp
#25
(11) ISO-1: Western Europe, ISO-8859-1
Setting procedures
25 CODE PAGE
C.P.:
C.P.:
C.P.:
C.P.:
C.P.:
C.P.:
437
850
857
858
860
861
C.P.:
C.P.:
863
865
C.P.: BRASCII
C.P.: ABICOMP
C.T.:
ISO-1
Alternate graphics mode (AGM) (IBM)
Function
This function enables the alternate graphics mode
(AGM) commands to be used.
Setting procedures
#26
26 AGM IBM
AGM is invalid.
AGM is valid.
AGM :
AGM :
NO
YES
Supplementary notes
This function enables the IBM mode to use the high-density
graphic printing function originally available in the EPSON
mode.
When the AGM function is valid, the software command
available in the EPSON mode can be used even in the IBM
mode.
Command
ESC 3 n
ESC J n
ESC A n
AGM invalid (NO)
Specifying n/216" line feed pitch
Executing n/216" line feed pitch
Registering n/72" line feed pitch that Specifying n/60" line feed pitch
is specified with ESC 2.
AGM valid (YES)
Specifying n/180" line feed pitch
Executing n/180" line feed pitch
ESC
n1 n2
●
m
Unusable
Various graphic modes can be
executed.
— 3. Setup options —
3-28
Download from Www.Somanuals.com. All Manuals Search And Download.
CR code function
Function
This function specifies whether or not to feed a line
when the printer receives a carriage return (CR)
command.
#27
Setting procedures
27 CR SETTING
Carriage return without a line feed
Carriage return with a line feed
AUTO FEED signal enabled
CR :
CR :
CR :
CR ONLY
CR + LF
AUTOFEED
Supplementary notes
1. EPSON mode
If AUTOFEED is selected, the printer checks the AUTO
FEED signal during initialization. It executes a carriage
return with a line feed when the AUTO FEED signal is low.
It executes a carriage return with out a line feed when the
AUTO FEED signal is high. The AUTO FEED signal is
usable only when the PARALLEL interface or AUTO is
selected. A carriage return without a line feed is executed
when the SERIAL interface is selected.
2. IBM or HP mode
If AUTOFEED is selected, a carriage return without a line
feed is executed.
LF code function
Function
This function specifies whether or not to execute a
carriage return when the printer receives a line feed
(LF) command.
#28
Setting procedures
28 LF SETTING
LF :
LF :
LF ONLY
LF + CR
Line feed without a carriage return
Line feed with a carriage return
— 3. Setup options —
3-29
Download from Www.Somanuals.com. All Manuals Search And Download.
Accent character
Function
This function specifies the method of printing accent
characters.
#29
Setting procedures
29 ACCENT CHR.
(Printing Example)
~
PRINT: SIMPLE
A
~
PRINT: COMPO.
A
Supplementary notes
When SIMPLE is selected, the accent character of the
resident font is printed. When COMPO. is selected, the
accent symbol and the character are printed separately to
add the accent symbol in the proper position.
Zero font style
Function
Two types of zeros are available: 0 with a slash, and 0
with no slash. This function allows the user to select
either font.
#30
Setting procedures
30 ZERO STYLE
ZERO: NO-SLSH
0
ZERO: SLASHED
0
Supplementary notes
The use of the slashed zero font helps to distinguish zero (0)
from the capital alphabetic letter "O".
— 3. Setup options —
3-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Horizontal tab
Function
The actual position of the horizontal tab depends on the
processing of the selected emulation.
#31
Setting procedures
31 TABULATION
TAB: 8 CHAR
TAB: 10 CHAR
TAB: 12 CHAR
TAB: 2 CHAR
TAB: 4 CHAR
TAB: 6 CHAR
Output data can be printed within the printable area of the form by
adjusting the tab when outputting nested program lists.
Locking page length
Function
This function specifies whether or not to change the
page length specified in the SETUP MODE by a
software command.
#32
Setting procedures
32 PAGE LOCK
LOCK: NO
LOCK: YES
Software command is valid.
Software command is invalid.
Supplementary notes
The right and left margins can be changed by software
commands regardless of this function. This function can also
specify whether or not to change the top and bottom margins
by a software commands.
— 3. Setup options —
3-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Locking font
Function
This function specifies whether or not to change the
typeface of font selected in the SETUP MODE by a
software command.
Setting procedures
#33
33 FONT LOCK
LOCK: NO
LOCK: YES
Software command is valid.
Software command is invalid.
Locking character pitch
Function
This function specifies whether or not to change the
character pitch selected in the SETUP MODE by a
software command.
#34
Setting procedures
34 PITCH LOCK
Software command is valid.
Software command is invalid.
LOCK: NO
LOCK: YES
— 3. Setup options —
3-32
Download from Www.Somanuals.com. All Manuals Search And Download.
Locking character quality
Function
This function specifies whether or not to change the
character quality selected in the SETUP MODE by a
software command.
#35
Setting procedures
35 QLTY LOCK
Software command is valid.
Software command is invalid.
LOCK: NO
LOCK: YES
Locking character table
Function
This function specifies whether or not to change the
character table selected in the SETUP MODE by a
software command.
#36
Setting procedures
36 CHR TBL LOCK
Software command is valid.
Software command is invalid.
LOCK: NO
LOCK: YES
— 3. Setup options —
3-33
Download from Www.Somanuals.com. All Manuals Search And Download.
FF code set at TOF position
Function
This function specifies whether or not FF (Form Feed)
is executed at TOF.
When “YES” is set, the FF code performs Form Feed even if
the present position is at TOF.
When “NO” is set, the FF code is ignored when the present
position is at TOF.
#37
Setting procedures
37 FF CODE/TOF
FF CODE/TOF : YES
FF CODE/TOF : NO
Supplementary notes
Certain kinds of software send commands to feed a
blank page without printing. Select "FF CODE/TOF
:NO" to neglect this command.
— 3. Setup options —
3-34
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the graphic printing speed
Function
120DPI, 180DPI, 240DPI and 360 DPI graphic
printing speeds are set.
#38
Setting procedures
38 GR QLTY
QLTY : MODE1
QLTY : MODE2
QLTY : MODE3
Supplementary notes
Graphic MODE
MODE 1
Printing speed Quality
Slow
Fine
MODE 2
Normal
Fast
Normal
Coarse
MODE 3
The graphic printing speed setting selects the character
quality in the panel setting and is effective only when
"Quality : NORMAL LQ" is selected.
— 3. Setup options —
3-35
Download from Www.Somanuals.com. All Manuals Search And Download.
Validity of bar code and enlarged character
Function
This function specifies whether or not to activate the
bar code and enlarged character function. If MODE 1
or MODE 2 is selected, the bar code and enlarged
character can be printed.
#40
See page 5-1 for details of the bar code.
See page 5-16 for details of the enlarged character.
Setting procedures
40 BC / L.CHR
BC: MODE 1
BC: MODE 2
BC: IGNORED
Bar code and enlarged character are valid.
Bar code and enlarged character are invalid.
If MODE 1 is selected, ESC SI or ESC SO cannot be used for
the bar code data start or stop command.
If MODE 2 is selected, ESC SI or ESC SO can be used for the
bar code data start or stop command.
— 3. Setup options —
3-36
Download from Www.Somanuals.com. All Manuals Search And Download.
Bar code type
Function
This function specifies one of thirteen available types
of bar code.
The bar code type specified here is regarded as the default setting,
which can be changed by a software command.
#41
Setting procedures
41 BC TYPE
TYPE: INDST25
TYPE: INTRL25
TYPE: MATRIX
TYPE: CODABAR
TYPE: CODE11
TYPE: CODE39
TYPE: CODE93
TYPE: CODE128
TYPE: EAN-8
TYPE: EAN-13
TYPE:
TYPE:
TYPE:
TYPE:
UPC-A
UPC-E
POSTNET
ELEMENT
Industrial 2 of 5
CODE 128
Interleaved 2 of 5
Matrix 2 of 5
CODABAR
CODE 11
EAN-8
EAN-13
UPC-A
UPC-E
CODE 39
POSTNET
*
*
CODE 93
— 3. Setup options —
3-37
Download from Www.Somanuals.com. All Manuals Search And Download.
Bar code specifications
The table below shows the specifications of thirteen types of bar codes
available for the printer. Bar code printing examples are shown on the
previous page.
Remark
Check character
Bar code
Industrial 2/5
Structure ICG letters (#)
Sample data
1234567
5B4S
Yes
0-9
Yes
(Mod 10)
Yes
Interleaved 2/5
5B5S
No
0-9
1234567
Even number, including
check character. Data
length is variable.
(2 characters
as one unit)
(Mod 10)
Codabar
Matrix 2/5
Code 11
Code 39
Code 93
Code 128
EAN-8
4B3S
3B2S
3B2S
5B4S
3B3S
3B3S
2B2S
2B2S
2B2S
2B2S
2LB3SB
Yes
Yes
Yes
Yes
No
0-9,
Yes
(Mod 16)
Yes
1234567
1234567
Start and end codes are
sent by the user.
Special
characters: 24
0-9
(Mod 10)
Yes
Start and end codes are (∆)
code. Dual check character
Start and end codes are
asterisk (*) codes.
0-9,"-"
1234567
(Mod 11)
Yes
0-9,
AB,...(43)
ASCII
(128)
1234567
(Mod 43)
Yes
1234567
Two check characters
(Mod 47)
Yes
No
ASCII
(128)
1234567
(Mod 103)
Yes
8 digits (2 prefix code +5
data code+Check character)
13 digits (2 prefix code +10
data code+Check character)
No
0-9
4912345
(Mod 10)
Yes
EAN-13
UPC-A
No
0-9
0-9
0-9
0-9
491234567890
(Mod 10)
Yes
No
01234500006 12 digits (NSC+10 data+
(Mod 10)
Yes
Check character)
UPC-A (12-digit) data is
automatically converted into
UPC-E (10-digit) data.
6, 10 or 12 digits
UPC-E
No
01234500006
(Mod 10)
Yes
Postnet
No
123456789
(Mod 10)
(data +Check character)
"B" and "S" in the "Structure" column show the number of
bars and spaces which consist of one or two characters. LB
and SB mean long bar and short bar, respectively.
— 3. Setup options —
3-38
Download from Www.Somanuals.com. All Manuals Search And Download.
Bar code size
Function
This function specifies the default bar code size.
Setting procedures
42 BC SIZE
#42
BC SIZE :
BC SIZE :
BC SIZE :
BC SIZE :
1
1.5
2
2.5
Supplementary notes
The tables below show bar code sizes and attributes.
1.5 2.5
SIZE
1
2
NARROW BAR
WIDE BAR
NARROW SPACE
WIDE SPACE
2/120inch 3/120inch 4/120inch 5/120inch
6/120inch 9/120inch 12/120inch 15/120inch
2/120inch 3/120inch 4/120inch 5/120inch
6/120inch 9/120inch 12/120inch 15/120inch
INTER CHARA. GAP 2/120inch 3/120inch 4/120inch 5/120inch
BAR HEIGHT
8/12inch 8/12inch
12/12inch 12/12inch
HRI PRINT
HRI FONT
BELOW
OCR-B
CHECK CHARACTER Added
PRINT DENSITY
1/120 inch
Enlarged character size
Function
This function specifies the default size of enlarged
characters.
Setting procedures
#43
43 LARGE CH. SIZE
SIZE :
SIZE :
SIZE :
SIZE :
SIZE :
SIZE :
SIZE :
SIZE :
1
2
4
8
12
16
24
32
— 3. Setup options —
3-39
Download from Www.Somanuals.com. All Manuals Search And Download.
Software setup
Function
This function specifies whether or not to accept the
software set up command.
Setting procedures
44 SETUP COMMAND
#44
SETUP: VALID
Setup can be specified by
a software command.
SETUP: IGNORED 1
SETUP: IGNORED 2
Supplementary notes
The setup command is ignored when "IGNORED 1" is selected.
The setup command and paper path command are ignored when
"IGNORED 2" is selected.
PCL mode (HP)
Function
This function specifies the emulation level in the HP
mode.
Setting procedures
#50
50 PCL MODE
EML: PCL3+
EML: PCL3
EML: PCL3+D
PCL3:
Fully compatible with the RuggedWriter 480. The character
pitches (15,17.1 and 24) and print quality modes (HQDR,NLQ,
S.D.,S.S.D.) cannot be selected by software commands.
PCL3+:
Extra capability to the RuggedWriter 480. In this mode,
additional character pitches, print quality modes, and raster
gaphics resolutions may be selected by software command.
PCL3+D:
Limited DeskJet compatibilty. In this mode, the commands
“ESC * P # Y” and “ESC * p # X” define units in 1/360”.
If you want print DeskJet application data,you can make use of
PCL3+D. The print position and graphics of the PCL3+D are
closer than the other two modes to the DeskJet.
— 3. Setup options —
3-40
Download from Www.Somanuals.com. All Manuals Search And Download.
Secondary character table (HP)
Function
This function specifies the symbol set of the
secondary character set in the HP mode.
#51
Setting procedures
51 CHR TB2 HP
LINE DRAW
MATH-7
TBL: LINE
TBL: MATH
Setting Option
Function
This function specifies whether or not to install
option.
#60
Setting procedures
60
OPTION
NOT INSTALL
OPTION: CSF
The CSF can be used.
The rear tractor can be used.
OPTION: REAR Tr.
Supplementary notes
When the CSF (cut sheet feeder) is selected, the rear tractor
cannot be used. Similarly, when the rear tractor is selected,
the cut sheet feeder cannot be used.
— 3. Setup options —
3-41
Download from Www.Somanuals.com. All Manuals Search And Download.
Paper path
Function
This function selects the paper path from among eight
available selections.
This option has the same function as the PAPER PATH key on the
control panel.
#61
Setting procedures
61 PAPER PATH
PATH: MAN REAR
PATH: R.Tr FRNT
PATH: F.Tr
PATH: F.Tr
REAR
TOP
PATH: MAN FRNT
PATH: MAN TOP
PATH: CSF FRNT
PATH: CSF TOP
Supplementary notes
Priority is given to the most recent setting made with the PAPER
PATH key or in the EXTENDED SETUP MODE.
Automatic scrolling
Function
This function selects the timeout period for automatic scrolling.
When the preset timeout period has passed after data in the communication
buffer is processed, and no new data is received, the perforation of the current
page is fed to the paper cutter position, allowing printed data to be examined.
This timeout period can be set to 0.5, 1, 5, 10 or 15 seconds.
#62
This function is valid only when printing on fanfold paper.
Setting procedures
62 AUTO SCROLL
NO SCROLL
SCROLL : 0.5 SEC
SCROLL : 1 SEC
SCROLL : 5 SEC
SCROLL : 10 SEC
SCROLL : 15 SEC
— 3. Setup options —
3-42
Download from Www.Somanuals.com. All Manuals Search And Download.
Out-of-paper detection
Function
This function specifies whether or not to perform paper
bottom detection.
When NO is selected, printing continues for the page length that is
specified and out-of-paper is ignored even when the paper is out.
#63
Setting procedures
63 P.OUT DTCT
Out-of-paper detection is
DETECT: YES
performed.
Out-of-paper detection is
not performed.
DETECT: NO
Supplementary notes
This function should be set to NO when printing on paper
with binding holes or when using paper on which a
pattern is printed on the back.
Skew detection
Function
This function specifies whether or not to perform the
skew detection for checking whether paper has been
loaded manually on the skew.
#64
If YES is selected, the printer ejects the paper loaded on the skew.
Setting procedures
64 P.SKEW DTCT
Skew detection is performed.
DETECT: YES
DETECT: NO
Skew detection is not performed.
— 3. Setup options —
3-43
Download from Www.Somanuals.com. All Manuals Search And Download.
Paper jam detection
Function
This function specifies whether or not to perform the
paper jam detection.
#65
If YES is selected, the printer automatically stops printing in case
of paper jamming.
Setting procedures
65 P.JAM DTCT
Paper jam detection is
DETECT: YES
performed.
Paper jam detection is not
performed.
DETECT: NO
Line feed speed
Function
This function specifies the line feed speed.
The 1/2 or 1/3 line feed speed feeds paper more stably. It is useful
for thick paper, labeled sheets and multipart paper in continuous
printing.
#66
Setting procedures
66 LF SPEED
Line feeding at normal speed (60 lps)
Line feeding at half speed (30 lps)
Line feeding at 1/3 speed (20 lps)
SPEED: NORMAL
SPEED: 1/2
SPEED: 1/3
Supplementary notes
With the NORMAL line feed speed selected, the line feed
speed is reduced to half (i.e., 30 lps) when the line feed pitch
is 1/3 inch and below, or paper is loaded.
— 3. Setup options —
3-44
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting of the auto-scrolling position
Function
Set the position for executing auto-scrolling.
In the case of "TOF ONLY" : Auto-scrolling is performed
only when the present position is at TOF .
#67
"ANY POS" : If the perforation is between the paper cutter
and printing head position, auto-scroll is performed at any
position after a prescribed time after the printing.
Setting procedures
67 SCROLL POS.
SCROLL : ANY POS
SCROLL : TOF ONLY
— 3. Setup options —
3-45
Download from Www.Somanuals.com. All Manuals Search And Download.
Interface
Function
This function selects the parallel or serial interface.
Setting procedures
See page 7-1 for details of the parallel interface.
#70
See page 7-5 for details of the serial interface.
Setting procedures
70 INTERFACE
Parallel interface is selected.
I/F: PARALLEL
I/F: SERIAL
I/F: AUTO
RS-232C serial interface is selected.
Parallel and serial interfaces are switched
automatically.
Supplementary notes
The functions shown below are available according to the
interface type.
The printer is set to the standard parallel and serial interface
before shipment. If it does not print data properly, recheck
the functions shown below. For the settings for the serial
interface, refer to the manual of the computer.
EXTENDED SETUP MODE Factory setting Page
#70.INTERFACE
PARALLEL 3-46
#71.SELECT IN ENABLE
#81.BUFFER SIZE
#82.BUSY/ACK TIMING
#83.DATA LATCH TIMING
#84.ERROR STATUS
0
3-47
3-52
3-53
3-53
3-54
512 KB
TYPE 2
TYPE F.
YES.
EXTENDED SETUP MODE Factory setting Page
#70.INTERFACE PARALLEL 3-46
#71.SELECT IN ENABLE
#72.PARITY BIT
#73.DATA LENGTH
#74.STOP BIT
#75.PROTOCOL
#76.BAUD RATE
#77.SERIAL ERROR
#78.CTS ENABLE
#79.CD ENABLE
#80.DSR ENABLE
#81.BUFFER SIZE
0
Non
8 bits
1 bit
DTR
9600 bps
Print
No
3-47
3-47
3-48
3-48
3-49
3-49
3-50
3-50
3-51
3-51
3-52
No
No
512 KB
— 3. Setup options —
3-46
Download from Www.Somanuals.com. All Manuals Search And Download.
Printer select command
Function
This function specifies whether or not to perform the
printer select command.
#71
Setting procedures
71 SLCT IN ENBL
Printer select command is always
SLCT IN:
SLCT IN:
1
0
accepted.
Printer select command is always
ignored.
SLCT IN: I/F
Printer select command is accepted
when SELECT IN signal is set high.
It is ignored when SELECT IN
signal is set low.
Parity bit (Serial I/F)
Function
This function specifies the parity bit when the serial
interface is used.
#72
Setting procedures
72
PARITY BIT
PARITY : NON
PARITY : EVEN
PARITY : ODD
Parity check is not executed.
Even number check is executed
Odd number check is executed.
— 3. Setup options —
3-47
Download from Www.Somanuals.com. All Manuals Search And Download.
Data length (Serial I/F)
Function
This function specifies the data length when the serial
interface is used.
#73
Setting procedures
73 DATA LENGTH
Data length is set to 8 bits.
Data length is set to 7 bits.
LENGTH: 8 BITS
LENGTH: 7 BITS
Supplementary notes
Select the data length: 8 bits or 7 bits.
Stop bit (Serial I/F)
Function
This function specifies the stop bit when the serial
interface is used
#74
Setting procedures
74 STOP BIT
Stop bit length is set to 1 bit.
Stop bit length is set to 2 bits.
STOP BIT: 1 BIT
STOP BIT: 2 BITS
Supplementary notes
Select the stop bit length: 1 or 2 bits.
— 3. Setup options —
3-48
Download from Www.Somanuals.com. All Manuals Search And Download.
Protocol (Serial I/F)
Function
This function specifies the protocol for the serial
interface.
#75
Setting procedures
75 PROTOCOL
PROT: DTR
DRT (ready/busy) protocol is selected.
PROT: XON/OF1
X-ON/X-OFF protocol (I) is selected.
PROT: XON/OF2
PROT: ETX/ACK
X-ON/X-OFF protocol (II) is selected.
EXT/ACK protocol is selected.
Baud rate (Serial I/F)
Function
This function specifies the data transmission rate for
the serial interface..
#76
Setting procedures
76
BAUD RATE
SPEED:
SPEED:
SPEED:
SPEED:
2400 B
1200 B
600 B
SPEED:
SPEED:
SPEED:
SPEED:
38400 B
19200 B
9600 B
4800 B
300 B
— 3. Setup options —
3-49
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial error (Serial I/F)
Function
This function specifies whether or not to print asterisk
‘✽’ when a serial data transmission error occurs during
communication via the serial interface.
The serial data transmission error includes a parity error, framing
#77
error and over-run error.
Setting procedures
77 SERIAL ERROR
S. ERROR: PRINT
Asterisk (✽) is printed in case of error.
S. ERROR: IGNORED
Error is ignored.
Supplementary notes
If a serial data transmission error occurs with the SERIAL
ERROR option selected to PRINT, the data in error is printed
as asterisk "✽". If data exceeding the buffer size is sent while
the printer is busy, the excess data is ignored. If a serial data
transfer error occurs with the SERIAL ERROR option set to
IGNORED, the erroneous data is discarded.
CTS signal (Serial I/F)
Function
This function specifies whether or not to validate the
CTS (clear to send) signal.
When the X-ON/X-OFF protocol or ETX/ACK protocol is used,
the CTS signal is used to output data from the printer to the
computer.
#78
Setting procedures
78 CTS ENABLE
CTS:
CTS:
NO
CTS signal is ignored.
CTS signal is valid.
YES
Supplementary notes
If this option is set to NO, the printer sends data to the
computer regardless of the CTS signal status.
If this option is set to YES, the printer checks the CTS signal
status to send data to the computer.
— 3. Setup options —
3-50
Download from Www.Somanuals.com. All Manuals Search And Download.
CD signal (Serial I/F)
Function
This function specifies whether or not to validate the
CD (carrier detect) signal.
The CD signal indicates whether or not a modem is connected to a
communication line.
#79
Setting procedures
79 CD ENABLE
CD:
CD:
NO
CD signal is ignored.
CD signal is valid.
YES
Supplementary notes
If this option is set to NO, the printer processes the received
data as valid data regardless of the CD signal status.
If this option is set to YES, the printer checks the CD signal
status to receive data from the computer.
DSR signal (Serial I/F)
Function
This function specifies whether or not to validate the
DSR(data set ready) signal.
The DSR signal indicates the status of the modem or computer.
#80
Setting procedures
80 DSR ENABLE
DSR:
DSR:
NO
DSR signal is ignored.
DSR signal is valid.
YES
Supplementary notes
If this option is seto to NO, the printer processes the received
data as valid data regardless of the DSR signal status.
If this option is set toYES, the printer checks the DSR signal
status to receive data from the computer.
— 3. Setup options —
3-51
Download from Www.Somanuals.com. All Manuals Search And Download.
Input buffer size
Function
This function specifies the size of the input buffer. The
buffer sizes shown below are provided.
#81
Setting procedures
81 BUFFER SIZE
B.SIZE:
B.SIZE:
B.SIZE:
512 KB
8 KB
Buffer size of512KB selected.
Buffer size of 8KB selected.
Buffer size of 128 bytes selected.
128 B
Supplementary notes
The buffer sizes shown below are provided.
Parallel I/F
CIN CRN
Serial I/F
BUFFER
SIZE
CIN
CRN
512K byte
8K byte
1K byte
32byte
2K byte 1K byte
64 byte 32 byte
2K byte
128 byte
64 byte
CIN :
The printer enters the busy state when the
available space in the buffer is reduced below the
CIN value.
CRN : The printer enters the ready state when the
available space in the buffer exceeds the CRN
value.
When the serial interface is used, processing differs
according to the protocol as shown below when the available
space in the buffer is inadequate.
Protocol
DTR
(Ready/Busy)
CIN processing
BUSY
CRN processing
READY
X-ON/X-OFF(I)
Sends X-OFF
Sends X-ON
X-ON/X-OFF(II)
ETX/ACK
Stops sending ACK Begins sending ACK
When the printer enters the CIN processing in the parallel
interface, data is input at 0.5 seconds intervals.
— 3. Setup options —
3-52
Download from Www.Somanuals.com. All Manuals Search And Download.
Busy/ACK signal timing (Parallel I/F)
Function
This function specifies the timing of the BUSY and
ACK signals transmitted via the parallel interface.
Setting procedures
#82
82 BUSY/ACK
ACK signal
TIMING:
TIMING:
TIMING:
TYPE 1
TYPE 2
TYPE 3
Rising edge
Center
Falling edge
Timimg
Type
BUSY
TYPE 1
ACK
BUSY
ACK
TYPE 2
TYPE 3
BUSY
ACK
Data latch timing(Parallel I/F)
Function
This function specifies the timing to latch DATA 1 ~ 8
at the falling edge (TYPE F.) or rising edge (TYPE R.)
of the STROBE signal.
#83
Setting procedures
83 DATA LATCH
STROBE signal
Falling edge
Rising edge
LTCH: TYPE F.
LTCH: TYPE R.
Type
Timimg
STROBE
TYPE F.
DATA 1~8
STROBE
TYPE R.
DATA 1~8
TYPE F
Data is read in when the STROBE signal goes Low.
TYPE R.
.
Data is read in when the STROBE signal goes High.
— 3. Setup options —
3-53
Download from Www.Somanuals.com. All Manuals Search And Download.
Error status signal output setting
(parallel interface)
Function
This function specifies whether or not to output the
parallel interface error status signal (PE, ERROR,
SELECT) when an error occurs.
#84
84 ERROR STATUS
ERROR STATUS: YES
ERROR STATUS: NO
When NO is selected, the status of the PE, ERROR,
and SELECT signals does not change even if the
printer is in out-of-paper, error, or offline state.
This function is effective when the system outputs
the printing data again when an error occurs.
— 3. Setup options —
3-54
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing direction
Function
The three printing directions shown below are available.
PRE-DIRECTION: Bi-directional printing 1
Printing is done in the shortest distance through logical seeking.
When double striking, vertical double-size character printing, or
other special effect printings require several passes, they are
carried out in the same direction as the first pass.
#90
BI-DIRECTION: Bi-directional printing 2
Logical seeking is carried out toward the closer printing start
position from the current head position to perform printing in
the shortest direction.
UNI-DIRECTION: Unidirectional printing
Printing is always done in the same direction, from the left to
right.
Setting procedures
90 PRINT DIR
PRINT: PRE-DIR
PRINT: UNI-DIR
PRINT: BI-DIR
Display language on LCD
Function
This function specifies the display language on the
LCD.
#91
Setting procedures
91 DISPLAY LANG
LANG: ENGLISH
LANG: DEUTSCH
LANG: FRANCAIS
LANG: ESPANOL
LANG: ITALIANO
English
German
French
Spanish
Italian
— 3. Setup options —
3-55
Download from Www.Somanuals.com. All Manuals Search And Download.
Locking panel keys
Function
This function specifies whether or not to validate the
keys other than the RESET key (i.e., ALT + TEAR
OFF keys) and ONLINE key in the ONLINE state.
#92
Setting procedures
92 KEY LOCK
Pressing a key is valid in the ONLINE
state.
KEY LOCK:
KEY LOCK:
NO
YES
Pressing a key is ignored in the ONLINE
state.
Locking reset key
Function
This function specifies whether or not to validate the
RESET key in the ONLINE state.
#93
Setting procedures
93 RESET LOCK
RESET key is valid in the ONLINE
state.
KEY LOCK: NO
KEY LOCK: YES
RESET key is ignored in ONLINE
state.
— 3. Setup options —
3-56
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting ENERGY STAR
Function
This function sets the power conservation standby mode.
When this mode is valid, if the standby mode continues
about 14 minutes after printing, the power conservation
mode is engaged. The normal mode is effective when
any print action is performed.
#94
Setting procedures
94 SLEEP MODE
SLEEP MODE : YES
SLEEP MODE : NO
Printing setup list
Function
This function prints the list of the parameters specified
in the setup mode.
#95
Setting procedures
95 SETUP LISTING
LIST : PATH & FORM
LIST : EXTEND
LIST : ALL SET
Display
Print
PATH&FORM
EXTEND
paths and six format memories.
Selectable paper
Parameters specified on the EXTENDED SETUP
MODE are printed.
ALL SET
All parameters specified in the setup modes and data in
the six memories are printed.
— 3. Setup options —
3-57
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Functions
High-speed printing
The printer has both standard and high-speed print modes.
The following table shows the print modes.
Selected with the QUALITY key or with #10 QUALITY in the SETUP MODE.
ESC x 1
ESC x 0
LQ is selected. Draft is selected.
SET UP
LQ
Draft
Draft
LQ
NLQ
LQ
NLQ
HQDR
DRAFT
S.D.
HQDR
Draft
LQ
S.D.
S.D.
S.S.D
S.S.D.
S.S.D
Printing speed
LQ (10 cpi)
180 CPS
240 CPS
360 CPS
603 CPS
723 CPS
904 CPS
NLQ (10 cpi)
HQDR (10 cpi)
DRAFT (10 cpi)
S.D. (12 cpi)
S.S.D. (15 cpi)
Print mode
(CPS=Character / Sec.)
When NLQ, HQDR, DRAFT, S. D. or S.S.D. is
selected, the graphic is printed at high speed with
lower bit density.
Operation procedures
Select a quality with the QUALITY key or with #10
QUALITY in the SETUP MODE.
See pages 2-3 and 3-17.
— 4. Functions —
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
GGFunctions
Enhancing the copying capability for multipart forms
The printer has an enhanced printing mode for printing on
multipart forms. With this function, the printer can print data
on a multipart form consisting of an original sheet and up to
eight sheets.
Operation procedures
Select a mode with #1 MULTIPART in the SETUP
MODE.
See page 3-8.
Setting the printing start position
This function specifies the printing start position from the top
of paper, from 0/60 to 63/60 inches, as shown below.
0/60 inch
63/60 inch
0/60~14/60 inch
The TOF position can be set from 0/60
inch (0 mm).
However, if it is set of 0/60 to 9/60
inch, paper may jamdepending on the
condition of the paper.
Caution
Printable area
Printable area
Normally, it is recommended that the
TOF position be adjusted to the 14/60
inch (approximately 6 mm) position
from the top of paper.
TOF position
#3 TOF ADJUSTMENT in
SETUP MODE
Operation procedures
See page 3-10.
Specify the TOF position using #3 TOF
ADJUSTMENT in the SETUP MODE.
If the TOF position needs to be changed further, press
the MICRO LF or MICRO RLF key to adjust the
printing start position.
The TOF SET key can also be used for fanfold paper.
(Be sure to close the printer cover when adjusting the
TOF position.)
— 4. Functions —
4-2
Download from Www.Somanuals.com. All Manuals Search And Download.
GGFunctions
Feeding perforation to the cutter position
This function feeds the perforation of paper to the paper cutter
position to cut the paper easily. It is useful for ejecting paper
to the top of the printer when the front or rear tractor is used.
Operation procedures
Press the TEAR OFF key to feed the perforation to
the paper cutter. Cut the paper, then press the TEAR
OFF key again. The paper is fed back to the
previous position.
See page 2-1.
To cut the paper fed out from the front of the tractor,
hold the upper cover firmly with one hand and tear
the paper towards you down wards.
Although safe, take care not to brush your fingers
along the edge of the paper cutter.
!
Caution
Use the paper cutter attached to the upper cover to cut
Caution
the paper. Using another part of the printer to cut the
paper forcibly may result in damage to the printer.
Paper cutter
1
— 4. Functions —
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
GGFunctions
More stable paper feeding
This function controls the line feed speed to feed thick
copying paper more stably.
In the 1/2 or 1/3 mode, line feeding is always carried out at 1/3 or 1/2
speed. This function is useful for printing data on multipart forms.
Operation procedures
Select the mode using #66 LF SPEED in the
EXTENDED SETUP MODE.
See page 3-44.
When the multipart forms are bound by paper staples or paper fasteners,
select FASTENER MODE: YES in the #15 paper fastener mode setting.
When the perforation peak of the multipart fanfold paper is too high, select
HEAD LIFT UP: YES in the #16 the head-up mode setting.
Operation procedures
Select the mode using #15 paper fastener mode
setting and #16 perforation head-up mode setting in
the SETUP MODE.
See page 3-22.
Automatically feeding perforation to the paper cutter
position in the standby condition
This automatic scroll function feeds the perforation to the
paper cutter position automatically when no data is received
for a preset period.
If the input buffer becomes empty in the ONLINE state and no input data
is received for a preset period (0.5, 1, 5, 10 or 15 seconds), the printer
automatically feeds the perforation at the top of the next page to the paper
cutter position and waits in this standby mode until additional input data is
received.
When the printer receives additional input data in this standby condition, it
reverse feeds paper to the correct print position and resumes printing there.
If the perforation is located at the paper cutter position when the input buffer
becomes empty, no paper motion action occurs.
When TOF ONLY is selected together with #67 AUTO SCROLL
POISITION, auto scrolling takes place only when the present position of the
paper is TOF.
Operation procedures
Select a mode using #62 AUTO SCROLL in the EXTENDED
SETUP MODE.
See page 3-42.
— 4. Functions —
4-4
Download from Www.Somanuals.com. All Manuals Search And Download.
GGFunctions
EEPROM initialization 1
Used for restoring settings made in the setup mode to the
factory default settings.
This operation initializes all parameters on the SETUP MODE and
.
EXTENDED SETUP MODE
Operation procedures
1.
Keep the LINE FEED, EJECT/LOAD, PAPER
PATH and PAPER FORM keys depressed, and
turn on the printer.
2.
The message shown below is displayed on the
LCD. The EEPROM is initialized.
EEPROM INITIAL 1
EEPROM initialization 2
This operation 2 initializes almost all factory default settings.
EEPROM intialization 2 = EEPROM intialization 1 + learning sensor.
Operation procedures
1.
2.
Set 15-inch fanfold paper to the front tractors in
the parking position.
Keep the ALT. REVERSE LF, PAPER PATH and
PAPER FORM keys depressed, and turn on the
printer.
3.
The message shown below is displayed on the
LCD. The EEPROM is initialized.
EEPROM INITIAL 2
— 4. Functions —
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
GGFunctions
Correcting vertical misalignment
The printer has two printing adjustment modes to correct misalignment
due to printer instrumentation error or aging deterioration: printing start
position adjustment mode (mode A), and bi-directional printing position
adjustment mode (mode B). These two modes allow the printing position
to be corrected properly.
The printing start position adjustment mode (mode A) corrects
misalignment in the printing start positions for printing at different speeds.
This allows data to be printed at the same start position even at different
printing speeds.
The bi-directional printing position adjustment mode (mode B) corrects
misalignment in bi-directional printing at the same printing speed. It
selects the proper correction value for each printing speed.
A change in mode A has effects mode B. If a change is
made in mode A, mode B must also be set properly. The
printer starts up in mode A and then enters mode B
automatically. If no change is made in mode A, the
printing position can be changed in mode B only.
Operation procedures
1. Set fanfold paper that is 10 inches or more in
width to the printer. Feed one or more pages of
paper and then select this mode.
2. Keep the SET UP and EJECT/LOAD keys
depressed and turn on the printer. The printer
enters the printing position adjustment mode.
Keep SET UP and EJECT/LOAD keys depressed and turn on the printer
Key
ALIGN ADJUST
Display
A: START POS.ADJ
B: VERT ADJ
or
key,
3. Select a mode with the
then press the ENTER key.
The procedures shown below are used for both modes A
and B.
— 4. Functions —
4-6
Download from Www.Somanuals.com. All Manuals Search And Download.
GGFunctions
4. Press the ENTER key and the timing pattern in
mode A (or mode B) will be printed.
Numbers marked with asterisks indicate the currently set
timing numbers. In mode A, modes 1 to 11 are printed. In
mode B, modes 0 to 11 are printed.
In each mode, 13 timing patterns are printed.
5. Select a speed mode number to be changed in the
printed patterns.
Select with
or
key.
A-MODE 1: NO.6
A-MODE 3: NO.6
For example, mode 1 is changed to mode. 3.
6. Select the best aligned pattern in the same speed
mode.
Check the alignment of the two line"H"printing.
7. Then press the ENTER key.
Select with
or key.
A-MODE 3: NO.6
For example, mode 6 is changed to mode 8.
A-MODE 3: NO.8
The selected timing is temporarily stored in the printer, and
test printing is executed at that timing.
8. Repeat steps 5 to 7 to change the speed modes.
9. Press the EXIT key to finish setting.
The timing stored temporarily is saved in the setup memory
(EEPROM). Therefore, be sure to press the EXIT key to exit
the mode.
10. Processing when the EXIT key will be pressed
differs according to the mode as shown below.
a. If mode A is exit, the menu of mode B will be displayed.
Press the ENTER key, and the patterns of mode B are
printed. Hereinafter, follow step 5 and so on.
b. If mode B is exit, the printer is reset automatically and
exits mode B.
— 4. Functions —
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
GGFunctions
Using various types of paper
The printer has six memories for saving data on forms:
MEMO 1 to MEMO 6. The following shows an example of
storing the sizes of three forms used in the manual mode in
MEMO 1 to MEMO 3.
Operation procedures
1. Press the PAPER PATH key to select MANUAL →
FRONT.
2. Press the PAPER FORM key to select MEMO 1.
3. Specify the A5 portrait form with #4 PAGE LENGTH
in the SETUP MODE, then save the setting as shown
below.
F.TR. REAR 11x15
MAN FRNT A4 p
MAN FRNT 11x15
PAPER PATH
SET UP
PAPER FORM
MAN FRNT A4 p
MAN FRNT 11x15
1 MULTIPART
SIZE: A5 p
ENTER
PAGE: 11 INCH*
SIZE: A5 p
1 MULTIPART
SIZE: A5 p*
4 PAGE LENGTH
4 PAGE LENGTH
4 PAGE LENGTH
EXIT
ENTER
SAVE?: YES*
MAN FRNT A5 p
4. Likewise, specify the Letter portrait form in MEMO 2
and the A3 portrait form in MEMO 3. The following
messages will be displayed on the LCD.
MAN FRNT LT p
MAN FRNT A3 p
5. In printing, select the MEMO containing the form
size to be used with the PAPER FORM key.
See page 1-11.
— 4. Functions —
4-8
Download from Www.Somanuals.com. All Manuals Search And Download.
GGFunctions
Executing test printing
The printer can execute test printing.
Operation procedures
1. Keep the ONLINE and REVERSE LF keys depressed
and turn on the printer.
2. The following message will be displayed on the LCD.
The printer starts test printing.
DEMO PRINT LQ
3. To terminate test printing, turn the power switch to
off.
Key shortcut functions
Key shortcut functions are executed by pressing and holding
the corresponding keys while simultaneously turning on the
printer power. The following table shows the available
shortcut functions.
Operation
Self Test Draft
Self Test LQ
Hex Dump Draft
Hex Dump LQ
Demo Print Draft
Demo Print LQ
Vertical Alignment
EEPROM Initialization
Note that, if the EEPROM is initialized, all the data
specified in the EEPROM is deleted.
— 4. Functions —
4-9
Download from Www.Somanuals.com. All Manuals Search And Download.
GGFunctions
Setting the application software
driver
About Printer
Printer Driver is a section of your software that automatically translates
instructions from the software to your printer.
For example, when using some application softwares, if you want to
boldface or underline a word, the printer driver automatically translates
your specific boldface or underline instruction on your application
software to printer control command.
Different printers use different control codes for designating print styles.
Therefore, it is important that when you install your software, you select
the appropriate printer driver designed for your printer.
Printer driver selection
Select a suitable printer driver from the list of supported printers. This
would include either the Hewlett Packard RuggedWriter 480, Epson LQ-
2550 or IBM 2391. Each of these printer drivers should allow you to
access many of the features on your printer.
If this printer is not listed, look for the following printer drivers. While
this should allow you to print your document with your printer, it probably
will not allow you to access many features of the printer. A few of the
choices you may see are given below in order of preferences.
Hewlett Packard
RuggedWriter 480
DeskJet 500
Epson
IBM
LQ-2500/2550
LQ-1050/1000
EX-1000
2390/2391
Proprinter XL24E
Proprinter XL24
Proprinter 24P
Notes:
1. Set the emulation type in the extension setup options according to the
selection of printer driver. For example, when you select the Epson
LQ-2550 printer driver, you should set the emulation type to the Epson
mode.
2. If you select the DiskJet 500 printer driver, you should set the #50 PCL
MODE to PCL3+D.
— 4. Functions —
4-10
Download from Www.Somanuals.com. All Manuals Search And Download.
GGFunctions
Installing the Windows Printer Driver
The diskette provided with your printer contains the software you need to
operate your printer with Windows applications. Before you install the
printer driver, we recommend you to read the README.TXT file on the
diskette. The README.TXT file contains all the information necessary
to install the printer driver, as well as all other pertinent information
regarding this software.
The printer driver tells Windows what information to send to the printer,
including details about printer features, the printer interface, and fonts.
Follow the next procedure before installing the Windows printer driver.
1. Close all Windows applications. Otherwise you will get an error
message when you attempt to install the printer driver.
2. Set the following parameters of Memo 1-6 to the factory default setting
in the SETUP MODE.
#3 TOF ADJUSTMENT
#6 TOP MARGIN
#7 BOTTOM MARGIN
#8 LEFT MARGIN
#9 RIGHT MARGIN
#10 QUALITY
14/60 inch
0 LINE
0 LINE
0 CHAR
0 CHAR
LQ
#12 CHARACTER PITCH
#13 LF PITCH
10 CPI
6 LPI
#14 ZOOM IN/OUT
100 %
Set the following parameters to the factory default setting in the
EXTENDED SETUP MODE.
#20 EMULATION
#27 CR SETTING
#28 LF SETTING
#32 PAGE LENGTH LOCK
#33 FONT LOCK
EPSON
CR ONLY
LF + CR
NO
NO
#34 PITCH LOCK
#35 QUALITY LOCK
NO
NO
#36 CHARACTER TABLE LOCK NO
#44 SOFTWARE SETUP VALID
IMPORTANT INFORMATION
1. COPYING RESTRICTIONS:
You may copy this software under certain restrictions. You may make
a backup copy or copy onto a hard disk. No more than two (2) copies
of this software are permitted to be in existence at any one time.
Every copy must include all notices and markings contained in the
original provided by SEIKO Precision Inc.
2. NO LIABILITY FOR CONSEQUENTIAL DAMAGES:
In no event shall SEIKO Precision Inc. be liable for any special,
indirect, incidental, or consequential damages in any way relating to
the use or rising out of the use of this software.
— 4. Functions —
4-11
Download from Www.Somanuals.com. All Manuals Search And Download.
GGFunctions
Connecting the printer in the HP environment
Introduction
The HP emulation of the printer provides full compatibility with the
HP2235A RuggedWriter 480 printer.
The printer also provides features and capabilities beyond those ever
provided by the HP RuggedWriter printer. SEIKO Precision Inc. has
provided a means for you to access these extra capabilities for any new
applications that you may chose to print on the printer.
The extra capabilities of the printer are enabled for access through a
special control panel menu setting entitled "50 PCL MODE".
PCL Mode
• PCL3 MODE -Provides the basic RuggedWriter 480 emulation
command set.
• PCL3+ MODE –Provides extra capability to the RuggedWriter 480
command set that allows you to access many printer features through
extensions of the command set.
• PCL3+D MODE –Provides all features of PCL3+ and allows the vertical
and horizontal positioning to be set in increments of 1/360". This mode
provides a "limited" Deskjet capability, and is mainly intended for
printing from Windows using the Deskjet 500 driver. Print output from
this mode will not be identical to that of a Deskjet printer (300 vs. 360
dpi) but will be closer than the other 2 modes for this type of application.
Setup
The information provided below gives setup information of the basic
printer RuggedWriter emulation, details of the command set extensions
provided with PCL3+ and PCL3+D Mode, and information on configuring
the Serial I/O to the various Term Types used by the HP System.
Refer to the Setup options for details on using the SETUP and
EXTENDED SETUP MODE.
Configuring the Printer with the RuggedWriter Emulation
1. Set the #20 EMULATION on EXTENDED SETUP MODE to "HP".
2. Set the #50 PCL MODE on EXTENDED SETUP MODE to "PCL3".
Setting the PCL MODE to "PCL3" provides the command set identical
with that of the HP RuggedWriter 480.
— 4. Functions —
4-12
Download from Www.Somanuals.com. All Manuals Search And Download.
GGFunctions
Extra Capabilities for new Applications
Listed below is a summary of the expanded command sets available for
new applications. Refer to the HP software commands for details of using
the expanded command sets.
PCL3+ Mode
This operation mode provides the following extended capabilities:
Escape
Command
Description
Added Capability
BEL
Activates the printer's bell
Bell is now active.
ESC & k # W Controls the print direction
Unidirectional, Bidirectional, Predirectional
PC-850, ISO25, France 2, German2,
Spain 3, Legal, Math7, Math-Symbol,
ISO84 Portugal 2, ISO85 Spain 2
PC-850, ISO25, France 2, German2,
Spain 3, Legal, Math7, Math-Symbol,
ISO84 Portugal 2, ISO85 Spain 2
15, 17.1, 24 cpi
ESC ( # id
Assign the primary font
ESC ) # id
Assign the secondary font
ESC ( s # H
ESC ) s # H
Sets the character pitch
Sets the character pitch
(primary)
15, 17.1, 24 cpi
(secondary)
ESC ( s # T
ESC ) s # T
Sets the primary typeface
Sets the secondary typeface
Script, Orator, Orator-s, OCR-A, OCR-B
Script, Orator, Orator-s, OCR-A, OCR-B
Off, Mode1, Mode2, Mode3
ESC * b # M Select graphics data compression
ESC * t # R
Designates raster graphics resolution 60, 360 dpi
PCL3+D Mode
This mode provides all of the capabilities described above plus the
following:
Escape
Command
Description
Added Capability
ESC * p # X
ESC * p # Y
Sets horizontal positioning by dot
Sets vertical positioning by dot
1/360"
1/360"
— 4. Functions —
4-13
Download from Www.Somanuals.com. All Manuals Search And Download.
GGFunctions
Serial I/O -Configuring Term Types 18, 19, 21, 22, or 26
The printer may be attached as a spooled printer on your system. It
supports I/O status checking by responding to the interrogation string ESC
? DC1 and indicates its status concerning whether paper is loaded, printer
covers are closed, and whether or not the printer is ONLINE.
Use the printer's EXTENDED SETUP MODE to configure the following
parameters to match your host system settings:
70 INTERFACE
72 PARITY
Set to SERIAL
Set to match your host configuration as
NONE, EVEN or ODD match your host
setting
73 DATA LENGTH Set to match your host configuration
(Either 7 or 8 BITS)
74 STOP BIT
Set to match your host configuration
(Either 1 or 2 BITS)
75 PROTOCOL
76 BAUD RATE
Set to XON/XOFF 1
Set to match your host configuration as
300,600,1200,2400,4800,9600,19200, or
38400
— 4. Functions —
4-14
Download from Www.Somanuals.com. All Manuals Search And Download.
. Bar code and enlarged character
5
The printer can print bar codes and enlarged characters.
To activate the bar code and enlarged character function, set #40
BARCODE/ENLARGED CHAR to MODE 1 or MODE 2 in the
EXTENDED SETUP MODE.
This function is applicable to the EPSON or IBM or HP mode. This
section describes the outline and details of the bar code and enlarged
character function.
See page 3-36.
Outline of bar code function
The printer has 14 types of bar codes.
Software commands and options #40 to #42 on the EXTENDED
SETUP MODE are used to print bar codes and enlarged characters.
The software commands are unique to the printer. See the following
pages for details of these commands.
1.Industrial 2 of 5
2.Interleaved 2 of 5
3.Matrix 2 of 5
4.Codabar
8.Code 128
9.EAN-8
10.EAN-13
11.UPC-A
5.Code 11
12.UPC-E
6.Code 39
13.Postnet
7.Code 93
14. Element (Created in elements.)
Makeup of bar code
(Example) CODABAR
ICG
ICG
Check
STOP
START
Character
Character
Character
DATA
HRI
Margin
Barcode
Margin
Start Character : Initial character of data
DATA : Alphanumeric data
Check Character : Character for check errors in read data
Stop Character : Last character of data
HRI : Human Readable Interpretation
ICG : Gap between characters (Inter Character Gap)
Margin : Data-free portions must be provided on both sides.
Each data-free portion must be approximately ten
times as wide as the narrow space (NS).
— 5. Bar code and enlarged character function —
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Bar code function
●
Presettable bar code function list
(Example) CODABAR
Inter Character Gap
START
Character
STOP
Character
Wide Space
Narrow Space
Wide Bar
Narrow Bar
Check Character
HRI
Bar code command list
Function
Command
DC4 DC4 T
DC4 DC4 E
DC4 DC4 H
DC4 DC4 I
DC4 DC4 F
DC4 DC4 C
ESC SI
1.
2.
Bar code type
Element width
Bar code height
Setting HRI on and off
HRI font
3.
4.
5.
6.
Check character
7.
Starting the bar code data sequence
Ending the bar code data seqence
Bar code data sequence
8.
ESC SO
9.
DC4 DC4 B
DC4 DC4 D
DC4 DC4 G
DC4 DC4 N
DC4 DC4 R
DC4 DC4 S
DC4 DC4 V
DC4 DC4 @
10.
11.
12.
13.
14.
15.
Printing density
Guard bar expansion
Start and stop characters
Bar code rotational angle
Disabling HRI of the start and stop characters
Value input mode
16.
Initializing the bar code mode
See pages 3-37 and 3-38.
(1)
DC4 DC4
T
Bar code type:
Format: ASCII
DC4
14
20
DC4
14
20
T
54
84
n
n
n
Hex
Decimal
Function: Specifies the bar code type
n =0 Industrial 2 of 5
1 Interleaved 2 of 5
2 Matrix 2 of 5
3 Codabar
7 Code128
8 EAN-8
9 EAN-13
10 UPC-A
11 UPC-E
12 Postnet
4 Code11
5 Code39
6 Code93
255 Element Print
Parameter 255 (Element print) is used to print a bar code which is input element by
element. It can print a bar code which is not supported by the printer and is represented
by combining elements. Since data is input by elements, HRI printing is not performed
and no check digit is added to the bar code. The start and stop characters is also not
added.
— 5. Bar code and enlarged character function —
5-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Bar code function
●
(2) Element width: DC4 DC4 E
Format: ASCII DC4 DC4
E
n1 n2
Hex
Decimal
14
20
14 45 n1 n2
20 69 n1 n2
Function: Specifies the n2/120” or n2/180” width of the element n1.
(1 ≤n 2 ≤ 127)
120” or 180” is specified with the DC4 DC4 D command.
n1 = 0: Narrow bar
1: Wide bar
3: Wide space
4: Inter-character gap
2: Narrow space
The narrow bar width or narrow space is used as the element width for
Code 93, Code 128, EAN-8, EAN-13, UPC-A, and UPC-E.
One element width of bar 1: Narrow bar width
One element width of space 1: Narrow space width
The midium bar or wide space width is used as the midium element width
for Code 11. The wide element width is (wide bar width x 2 - narrow bar
width).
This setting is not valid for Postnet.
The inter-character gap means the space between each set of codes of a bar
code which begins with a bar and ends with a bar.
(3) Bar code height: DC4 DC4 H
Format: ASCII
Hex
DC4
14
20
DC4
14
20
H
48
72
n
n
n
Decimal
Function: Sets the bar code height to n/12”. (0 ≤ n ≤ 120)
The currently set line feed pitch serves as the bar code height when n
is set to 0. This setting is not valid for Postnet.
(4) Setting HRI on and off: DC4 DC4 I
Format: ASCII
DC4
14
20
DC4
14
20
I
49
73
n
n
n
See page 5-9.
Hex
Decimal
Function: Specifies whether or not to print an HRI. Also specifies the
HRI printing position if an HRI is to be printed.
n = 0: HRI not printed.
1: HRI printed below the bar code symbol.
2: HRI printed above the bar code symbol.
No HRI printed for Postnet or Element regardless of this setting.
— 5. Bar code and enlarged character function —
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Bar code function
●
(5) HRI font: DC4 DC4 F
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
F
46
70
n
n
n
Function: Selects the font of printing the HRI.
n = 0: Currently selected font
1: OCR-A
2: OCR-B
This setting is not valid for Postnet or Element.
(6) Check character: DC4 DC4 C
Format:
See pages 5-12 and -13.
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
C
43
67
n
n
n
Function: Specifies whether to add a check character automatically.
n = 0: No check character is added. (If a check character is needed, the
user must send bar code data.)
1: A check character is added. (The check character is not printed
in the HRI when Code 93 or Code 128 is selected.)
If the Codabar or Element is selected, no check character is added regardless of
this setting.
The following shows the methods of determining the check characters and bar
code types. (For details, see “Calculating the check character” below.)
Modulus 10 Industrial 2 of 5, Interleaved 2 of 5, Matrix 2 of 5, EAN, UPC,
Postnet
Modulus 11 Code 11 (Dual Check character)
Modulus 16 Codabar
Modulus 43 Code 39
Modulus 47 Code 93 (Dual Check character)
Modulus 103 Code 128
(7) Beginning of the bar code data sequence: ESC SI
Format: ASCII
ESC
1B
27
SI
0F
15
Hex
Decimal
Function: Indicates the beginning of a bar code data sequence.
Data between this and the end command of the bar code data sequence
is regarded as bar code data.
This command is valid only when #40 BARCODE/ENLARGED
CHAR is set to MODE 2 in the EXTENDED SETUP MODE.
— 5. Bar code and enlarged character function —
5-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Bar code function
●
(8) End of the bar code data sequence: ESC SO
Format: ASCII
ESC
1B
27
SO
0E
14
Hex
Decimal
Function: Indicates the end of a bar code data sequence.
This command is valid only when #40 BARCODE/ENLARGED CHAR is
set to MODE 2 in the EXTENDED SETUP MODE.
(9) Bar code data sequence: DC4 DC4 B
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
B
42
66
n
n
n
d1
d2 ... dk
Function: Specifies the number (“n”) of data to be regarded as bar code data.
00 ≤ n ≤ 68
00 ≤ dk ≤ 255
00 ≤ k ≤ 68
If the Element is selected; 0 ≤ n, dk, k ≤ 255
This comand is valid when #40 BARCODE/ENLARGED CHAR is set to MODE 1
or MODE 2 in the EXTENDED SETUP MODE.
(10) Printing density: DC4 DC4 D
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
D
44
68
n
n
n
Function: Specifies the density of printing bar code symbols (in the horizontal
direction).
Specifies the unit of element width.
n = 0:
1:
Bar code symbols are printed at 120 dpi. (Default value)
Bar code symbols are printed at 180 dpi.
If a bar code is rotated by 90 or 270 degrees using the DC4 DC4 R (bar code
rotational angle) command, a bar code is printed at 120 dpi horizontally and 180 dpi
vertically.
(11) Guard bar expansion: DC4 DC4 G
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
G
47
71
n
n
n
Function: Specifies whether or not to expand EAN or UPC guard bars.
n = 0: Guard bars are not expanded.
1: Guard bars are expanded. (Default value)
— 5. Bar code and enlarged character function —
5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Bar code function
●
(12) Start and stop characters: DC4 DC4 N
Format: ASCII
DC4
14
20
DC4
14
20
N
4E
78
n1
n1
n1
n2
n2
n2
Hex
Decimal
Function: Specifies the Codabar start or stop character. n1 selects the
start or stop character. n2 specifies a code of the start or stop character
as shown below.
n1 = 0: Start character
1: Stop character
n2 = a, b, c, d, t, n, , or e.
●
When power is turned on, “a” is selected as the start or stop character.
(13) Bar code rotational angle: DC4 DC4 R
Format:
ASCII
Hex
DC4
14
20
DC4
14
20
R
52
82
n
n
n
Decimal
Function: Specifies the rotational angle of the bar code in units of 90 degrees.
n = 0: 0° (Default value)
1: 90°
2: 180°
3: 270°
(14) Disabling HRI of the start and stop characters: DC4 DC4 S
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
S
53
83
n
n
n
Function: Specifies whether or not to print the start or stop character in the HRI
for Codabar, Code 11, Code 39 or Code 93.
n = 0: The start or stop character is printed in the HRI.
(Default value)
1: The start or stop character is not printed in the HRI.
(15) Value input mode: DC4 DC4 V
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
V
56
86
n
n
n
Function: Specifies whether bar code sequence data is regarded as the normal
character code or a character value when Code 128 is selected.
n = 0: Data is regarded as normal character code. (Default value)
1: Data is regarded as a character value.
If data is regarded as the normal character code, the printer
automatically move the subset or inserts a shift code according to
the data.
See page 5-11.
— 5. Bar code and enlarged character function —
5-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Bar code function
●
(16) Initializing the bar code mode: DC4 DC4 @
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
@
40
64
Function: Initializes the bar code mode.
The following show the default settings for bar code.
Bar code type:
SETUP
Narrow bar width:
Wide bar width:
Narrow space width:
Wide space width:
Inter- character gap:
Bar code height:
Setting HRI:
SETUP
SETUP
SETUP
SETUP
SETUP
SETUP
Below the bar code symbol
OCR-B
HRI font
Check character:
Printing density:
Added
1/120”
Data processing in the bar code data sequence
● In a bar code data sequence, any codes other than the ESC
code are regarded as bar code data.
In a bar cord sequence following ESC SI, continuous two-
byte ESC codes (ESC + ESC) are regarded as a one-byte
ESC bar code.
● In a barcode data sequence following ESC SI, ESC+ SO
and ESC + ESC are valid and the other ESC sequence are
ingnored. The ESC code and the following data, two bytes
in all, are discarded.
● When a start or stop character code (e.g., code of Code
*
39) is input in a bar code data sequence, the bar code data
sequence stops if bar code data has already been input in
that sequence. The data that was input is valid and
converted into a bar code. If not, the bar code data
sequence does not stop and the code is discarded.
● When 68 bytes of data is input, the bar code data sequence
ends automatically.
When Code 93 or Code 128 is selected, the bar code data
sequence ends when the amount of input data, including the
automatically inserted control character, reaches 68 bytes.
(Bar code buffer full)
— 5. Bar code and enlarged character function —
5-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Bar code function
●
Printing bar codes
●
●
●
Bar codes are printed at normal LQ 10 cpi (158 cps) print
speed when the printing density is 120 dpi or at Dark 1 LQ
10 cpi (79 cps) print speed when the printing density is 180
dpi. This does not apply to printing paths involving HRI
printing or duty control.
Bar codes and normal characters are printed separately.
When the bar code data sequence is processed, print data
other than bar code data contained in the buffer is printed.
When print data other than bar code data is input, bar
code data contained in the buffer is printed.
Like the right margin overflow processing for character
data, data preceding bar code data is printed and the bar
code data is printed from the left margin on the following
line if the data exceeds the right margin.
If bar code data cannot be printed between the left and
right margins, the bar code data is ignored.
●
●
When the number of bar code symbols in the buffer
reaches 68, printing starts. (Bar code buffer full printing)
If the vertical line feed pitch is smaller than the bar code
height, reverse feeding is performed to move to the
following printing position.
●
If an out-of-paper error is detected in a bar code printing
path, the following paths are printed on the following
form.
— 5. Bar code and enlarged character function —
5-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Bar code function
●
H R I
●
The HRI is adjusted to the center of the bar code symbol
width and printed at 10 cpi unless EAN or UPC guard bar
expansion is executed. If EAN or UPC guard bar
expansion is executed, an HRI is printed at the equal space
between the center guard bar and the left or right guard
bar.
If the HRI width is greater than the bar code symbol width,
the HRI printing pitch is reduced to print the HRI in the
same width as the bar code symbol width.
●
The HRI is printed below a bar code symbol, the vertical
printing position is lower than the printing start position
by (bar code height - 1/6”). If it is printed above the bar
code symbol, the vertical printing position is higher than
the printing start position by (1/6” - 24/180”).
●
●
When Code 11 is selected, small triangle (
●) and large
triangle ( ) are printed as the start and stop characters,
●
respectively. (This does not depend on the setting of the
check character.)
When Code 93 is selected, white squares (
●
) are printed
as the start and stop characters, and a black square (
●) is
printed as the control character. A printable character
expressed in combination with the control character is
printed as is. (For example, 61H is printed as ‘a’, not ‘
A’.)
●
●
When Code 128 is selected, black rhombuses (●) are
printed instead of non-printable characters (00H to IFH
and 7FH).
— 5. Bar code and enlarged character function —
5-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Bar code function
●
●
If a character code that is not valid for the selected bar
code type is input, the character code is not converted into
a bar code symbol but is printed as a character. If the bar
code has a start or stop character added to the HRI, the
Error processing
start or stop character is printed. ‘
of an invalid character.
’ is printed instead
●
If an incorrect number of data are input to form a bar code
which should have a specific number of data, the input
data is not converted into a bar code symbol but is printed
as a character.
●
If incorrect data is input in the UPC-A format and cannot
be converted into the UPC-E format, the input data is not
converted into a bar code symbol but is printed as a
character. (For the rules of converting the UPC-A format
into the UPC-E format, see “UPC-E conversion rule”
below.)
— 5. Bar code and enlarged character function —
5-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Bar code function
●
Code 128 subset transition rule
●
The following shows the transition conditions from subset
A to subset B.
1. Input a character code unique to subset B (60H
to 7FH) when subset A is selected.
2. Then input a character code unique to subset B
(60H to 7FH) without inputting a character code
unique to subset A (00H to 1FH). (If a character
code unique to subset A is input in this step,
subset B is not selected. The character code
unique to subset B input in step 1 is expressed
with the shift code.)
●
The following shows the transition conditions from subset
B to subset A.
1. Input a character code unique to subset A when
subset B is selected.
2. Then input a character code unique to subset A
without inputting a character code unique to
subset B. (If a character code unique to subset B
is input in this step, subset A is not selected. The
character code unique to subset A input in step 1
is expressed with the shift code.)
●
●
Subset C is selected when four continuous character codes
(30H to 39H) are input.
If a code common to subset A and subset B is input when a
subset is not determined or subset C is selected, subset B is
temporarily selected.
— 5. Bar code and enlarged character function —
5-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Bar code function
●
UPC-E conversion rule
●
NSC, manufacturer’s codes (M1 M2 M3 M4 M5), and
product item codes (X1 X2 X3 X4 X5) are input data.
1. NSC must be 0 or 1.
2. When the manufacturer’s code data is input,
the rule is determined and zero checking of the
product item codes is performed.
NZ: Non-zero
: 0 to 9
●
UCP-A Type
M1 M2 M3 M4 M5 X1 X2 X3 X4 X5
●
●
●
●
●
●
●
●
●
●
●
NZ
0
Rule 1
Rule 2
Rule 3
Rule 4
NZ
0
0
0
0
0
0
0
0
0
0
0
0
5 ~ 9
●
0
●
●
●
3 ~ 9
0 ~ 2
0
0
●
●
0
0
3 . The following table shows print data if the rule
shown above is met.
UCP-E Type
Rule 1
Rule 2
Rule 3
Rule 4
M1 M2 M3 M4 M5 X5 (5 ~ 9)
M1 M2 M3 M4 X5
M1 M2 M3 X4 X5
'4'
'3'
M1 M2 X3 X4 X5 M3 (0 ~ 2)
Calculating the check character
• Modulus 10
a. The data at the odd-numbered position counted from the right are
weighed as 3. The sum of the data character values is determined..
(The sum is determined without weighing for Postnet.)
b. The remainder after dividing the value determined in step a by 10 is
determined.
c. The check character is the character value determind by subtracting
the remainder in step b from 10.
— 5. Bar code and enlarged character function —
5-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Bar code function
●
• Modulus 11
a. Data characters are weighed from the right to the left, as,
example,1, 2, ..., 10, 1, 2 ... 10, 1, 2 and so forth. The sum of
the data character values is determined. (The symbol ‘-’ has a
character value of 10.)
b. A character having a character value equal to the remainder of
dividing the value determined in step a by 11 is the first check
character (C).
c. Data characters are weighed from the right to the left,
beginning with C, as, for example, 1, 2, ..., 9, 1, 2 ... , 9, 1, 2
and so forth. The sum of the data character values is
determined.
d. The character with a character value equal to the remainder of
dividing the value determined in step c by 11 is the second
check character (K).
• Modulus 16
a. The sum of the all characters including start and stop
characters values is determined. The following table shows the
conversion of character into value.
Value Character Value Character Value Charactr Value Character
0
4
8
12
16
0
4
8
:
1
5
9
13
17
1
5
9
/
2
6
10
14
18
2
6
-
.
C
3
7
11
15
19
3
7
$
+
D
A
B
b. The remainder X of deviding the value determined in step a
by 16 is determined. The remainder Y of subtracting the
remainder X from 16 is determined.
c. Convert the remainder Y into the character Z according to the
conversion table in a. The character Z is the check character.
• Modulus 43
a. The sum of the data character values is determined.
b. The character with a character value equal to the remainder of
dividing the value determined in step a by 43 is the check
character.
— 5. Bar code and enlarged character function —
5-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Bar code function
●
• Modulus 47
a. Data characters are weighed from the right to the left, as, for
example, 1, 2, ..., 20, 1, 2 ... 20, 1, 2 and so forth. The sum of
the data character values determined..
b. The character with a character value equal to the remainder of
dividing the value determined in step a by 47 is the first check
character (C).
c. Data characters are weighed from the right to the left,
beginning with C, as, for example, 1, 2, ..., 15, 1, 2 ... , 15, 1, 2
and so forth. The sum of the data character values is
determined.
d. The character with a character value equal to the remainder of
dividing the value found in step c by 47 is the second check
character (K).
• Modulus 103
a. The sum of the products of the data character values and
position values is determined. (The leftmost character has a
position value of 1.)
b. The start character value is added to the sum determined in
step a above.
c. The character with a character value equal to the remainder
of dividing the value determined in step c by 103 is the check
character.
Other
●
After executing a BS command input immediately after bar
code data, printing starts from the position by one
character to the left of the currently set character pitch.
●
●
●
When a margin is specified, bar code data in the buffer is
cleared.
Element printing
The element printing function prints bar codes by inputting
data element by element.
This function allows the user to print bar codes which are
not supported by the printer but are expressed by
combining elements. No HRI is printed, no check digit is
added, and a start or stop character is not added, since
data is input element by element.
●
The following show the codes expressing elements.
00H:
01H:
02H:
03H:
04H:
Narrow bar
Wide bar
Narrow space
Wide space
Inter-character gap
— 5. Bar code and enlarged character function —
5-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Bar code function
●
Element printing
[Example]
The following shows a BASIC program for printing Code 39 bar codes
using the element printing function. This example shows how to print
“CODE39”. (Replace NB, WB, NS and WS in the data statements in the
following example with 0, 1, 2 and 3, respectively.)
100 OPEN "LPT1:" AS #1: WIDTH #1,255
110 DC4$=CHR$ (&H14): ESC$=CHR$(&H1B)
120 SI$=CHR$(&HF):SO$=CHR$(&HE): ICG=4
130 '
140 PRINT #1, DC4$;DC4$;"@";
' Initialize
150 PRINT #1, DC4$;DC4$;"T";CHR$(255); ' Barcode Type: Element Print
160 PRINT #1, DC4$;DC4$;"E";CHR$(0);CHR$(2); ' Narrow Bar: 2/120"
170 PRINT #1, DC4$;DC4$;"E";CHR$(1);CHR$(6); ' Wide Bar: 6/120"
180 PRINT #1, DC4$;DC4$;"E";CHR$(2);CHR$(2); ' Narrow Space: 2/120"
190 PRINT #1, DC4$;DC4$;"E";CHR$(3);CHR$(6); ' Wide Space: 6/120"
200 PRINT #1, DC4$;DC4$;"E";CHR$(4);CHR$(2); ' Inter Char Gap: 2/120"
210 PRINT #1, DC4$;DC4$;"H";CHR$(6);
220 '
' Barcode Height: 6/12"
230 PRINT #1, DC4$;DC4$;"B";CHR$(9*8+7); ' Barcode Data Sequence Start
240 RESTORE 440
250 FOR I=1 TO 9:READ A:PRINT CHR$(A);:NEXT I
260 PRINT #1, CHR$(ICG);
270 FOR J=1 TO 6
280 IF J=1 THEN RESTORE 450
290 IF J=2 THEN RESTORE 460
300 IF J=3 THEN RESTORE 470
310 IF J=4 THEN RESTORE 480
320 IF J=5 THEN RESTORE 490
330 IF J=6 THEN RESTORE 500
340 FOR I=1 TO 9:READ A: PRINT #1, CHR$(A);:NEXT I
350 PRINT #1, CHR$(ICG);
360 NEXT J
370 RESTORE 440
380 FOR I=1 TO 9:READ A: PRINT #1, CHR$(A);:NEXT I
400 PRINT #1,CHR$(13);CHR$(10);
410 CLOSE #1
' CR+LF
420 END
430 '
440 DATA 0, 3, 0, 2, 1, 2, 1, 2, 0
450 DATA 1, 2, 1, 2, 0, 3, 0, 2, 0
460 DATA 1, 2, 0, 2, 1, 2, 0, 3, 0
470 DATA 0, 2, 0, 2, 1, 3, 0, 2, 1
480 DATA 1, 2, 0, 2, 1, 3, 0, 2, 0
490 DATA 1, 2, 1, 3, 0, 2, 0, 2, 0
500 DATA 0, 2, 1, 3, 0, 2, 1 ,2, 0
— 5. Bar code and enlarged character function —
5-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Enlarged character function
●
If #40 BARCODE/ENLARGED CHAR is set to MODE 1 or MODE 2
in the EXTENDED SETUP MODE, enlarged characters can be
printed. The enlarged character function is valid for the EPSON or
IBM or HP mode.
See page 3-36.
Outline of enlarged character function
When the enlarged character mode is selected with the DC4 DC4 I 1
command, any commands other than those shown below are ignored.
Only three print codes are available: LF, CR and FF. If 521 or more
characters of data are sent without inputting a print command, printing
is performed automatically.
Enlarged character command list
Function
Command
BS
Executing backspacing
Executing line feeding
Executing form feeding
1.
2.
LF
3.
FF
Executing carriage return
4.
CR
Initializing the enlarged character mode
Arrangement of enlarged characters
Element magnification for enlarged characters
All-character set for enlarged characters
Selecting an enlarged character font
Height expansion for enlarged characters
HMI for enlarged characters
5.
DC4 DC4 @
6.
DC4 DC4
DC4 DC4
DC4 DC4
DC4 DC4
DC4 DC4
DC4 DC4
DC4 DC4
DC4 DC4
DC4 DC4
DC4 DC4
DC4 DC4
DC4 DC4
DC4 DC4
DC4 DC4
DC4 DC4
DC4 DC4
DC4 DC4
DC4 DC4
a
c
d
f
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
h
i
VMI for enlarged characters
j
Setting and canceling the enlarged character mode
Enlarged character cell offset
l
o
p
q
r
Enlarged character pitch
Enlarged character quality
Enlarged character rotational angle
Setting and canceling enlarged character smoothing
Enlarged character top offset
s
t
Setting and canceling underscores for enlarged characters
u
w
x
y
Enlarged character width expansion
Horizontal printing position for enlarged characters
Vertical printing position for enlarged characters
— 5. Bar code and enlarged character function —
5-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Enlarged character function
●
(1) Executing backspacing: BS
Format:
ASCII
Hex
Decimal
BS
08
08
Function: Executes backspacing.
When the BS command is executed, the printing position moves to the
previous character position on the left. The BS command is valid up to the
left margin. A BS command issued on the left margin is ignored.
When a BS command is issued when there is a character on the left with
proportional printing selected, the printer backspaces to that character. If
there is no character or another BS command has just been executed, the
printer backspaces by one space.
The part moved by backspacing is not underscored.
(2) Executing line feeding: LF
Format:
ASCII
Hex
Decimal
LF
0A
10
Function: Executes line feeding.
After printing data, the printer feeds one line by the enlarged character line
feed pitch, which differs depending on whether VMI is valid (by the DC4
DC4 j command) or not.
VMI valid: Preset VMI amount
VMI not valid: (24 + cell offset)/180” x cell expansion
Line feeding involves a carriage return if the LF SETTING option is set to
LF + CR in the EXTENDED SETUP MODE.
If the bottom margin is specified and the cell size (i.e., 24/180” x cell
expansion) is greater than the printable area in the CSF, cut sheet, or
fanfold paper mode, form feeding is executed and then printing is executed.
If the printing position is at the TOF position, printing is executed up to the
bottom margin without executing form feeding, and excess data is not
printed.
The default pitch is “1/6” x cell expansion”.
— 5. Bar code and enlarged character function —
5-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Enlarged character function
●
(3) Executing form feeding: FF
Format:
ASCII
Hex
Decimal
FF
0C
12
Function:
Executes form feeding.
This command feeds the page to the next TOF position. If there are still enlarged
characters to be printed, they are printed, then form feeding is executed.
(4) Executing carriage return: CR
Format:
ASCII
Hex
Decimal
CR
0D
13
Function:
Executes carriage return.
This command moves the printing position to the left margin without printing any
characters. If the CR SETTING option is set to CR + LF in the EXTENDED
SETUP MODE, a carriage return is executed out after printing.
(5) Initializing the enlarged character mode: DC4 DC4 @
Format: ASCII DC4
DC4
14
20
@
40
64
Hex
14
20
Decimal
Function:
Initializes the enlarged character mode.
The following show the default settings for enlarged characters:
Cell expansion:
Height expansion:
Width expansion:
Font:
SETUP expansion
SETUP expansion
SETUP expansion
SETUP font
Character pitch:
HMI:
10 cpi
Invalid
Cell offset:
6/180”
VMI:
Invalid
Character quality:
Character layout:
Rotational angle:
Smoothing:
Standard
Adjusted to the base line
0°
Valid
Top offset:
0/180”
Underscore:
Canceled
Character set:
Right and left margins:
Page length:
Set at enlarged character mode selected
Margin at enlarged character mode selected
Length at enlarged character mode selected
Margin at enlarged character mode selected
Top and bottom margins:
— 5. Bar code and enlarged character function —
5-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Enlarged character function
●
(6) Arrangement of enlarged characters: DC4 DC4 a
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
a
61
97
n
n
n
Function: Specifies the standard position for adjusting enlarged characters
in the vertical direction.
n = 00H,30H: Base line is adjusted to the N’th dot from the top.
(N = 20 x cell expansion)
01H,31H:
02H,32H:
03H,33H:
Descender is adjusted to the N’th dot from the top.
(N = 24 x cell expansion)
Center is adjusted to the N’th dot from the top.
(N = 12 x cell expansion)
Ascender is adjusted to the N’th dot from the top.
(N = 1 x cell expansion)
The MSB of the parameter is masked. Any parameters other than those
shown above are ignored.
The arrangement and position specified here are valid if the enlarged
character rotational angle is not 0 degree. The default setting is n =
00H,30H.
(7) Cell expansion for enlarged characters: DC4 DC4 c
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
c
63
99
n
n
n
Function: Specifies cell expansion for enlarged characters.
127
0
≤
n
≤
The cell has the size of (24/180” x cell magnification). The MSB of the
parameter is masked.
If n = 0, the expansion specified in the setup mode is selected.
The cell expansion is specified at the beginning of the line. If there is
character data on the line, it becomes valid on the following line.
Enlarged character cell expansion takes priority over the height expansion.
If the height expansion exceeds cell expansion when enlarged character
data is input, the characters are enlarged to the cell expansion value.
The default setting is the expansion specified in the setup mode.
— 5. Bar code and enlarged character function —
5-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Enlarged character function
●
(8) All-character set for enlarged characters: DC4 DC4 d
Format:
ASCII
DC4
DC4
14
20
d
64
100
n
n
n
d1
d1
d1
d2...dn
d2...dh
d2...dn
Hex
14
Decimal
20
Function: Specifies the all-character set for enlarged characters.
1
0
≤
≤
n
d
≤
≤
255
255
Data with a number specified with the parameter “n” is processed as
character codes. If n = 0, this sequence is ignored.
(9) Selecting an enlarged character font: DC4 DC4 f
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
f
66
102
n
n
n
Function: Specifies the font (typeface) of enlarged characters as shown
below.
n = 0: Roman
1: Sans serif
2: Courier
3: Prestige
4: Script
5: OCT-B
6: OCR-A
7: Gothic
8: Orator
9: Orator-S
The MSB of the parameter is masked. Any parameters other than those
shown above are ignored.
If the FONT LOCK option is set to YES in the EXTENDED SETUP
MODE, this command is ignored.
The default is the setting selected in the setup mode.
— 5. Bar code and enlarged character function —
5-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Enlarged character function
●
(10) Height expansion for enlarged characters: DC4 DC4 h
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
h
68
104
n
n
n
Function: Specifies the height expansion of enlarged characters.
127
0
≤
n
≤
The MSB of the parameter is masked.
If n = 0, the expansion specified in the setup mode is selected.
Enlarged character cell expansion takes priority over height expansion. If
the height expansion exceeds the cell expansion when enlarged character
data is input, the characters are enlarged to the cell expansion.
The default expansion is specified in the EXTENDED SETUP MODE.
(11) HMI for enlarged characters: DC4 DC4 i
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
i
69
105
n1
n1
n1
n2
n2
n2
Function: Specifies the HMI (horizontal motion index) of enlarged
characters.
0
0
≤
≤
n1
n2
≤
≤
255
15
The HMI indicates the horizontal distance between two adjacent characters,
i.e., the width the print head moves after printing one character.
The HMI is (n1 + n2 x 256)/180”.
The high-order four bits of parameter n2 (bit 7 to bit 4) are ignored. The
HMI can be set to zero.
After specifed command have priority over DC4 DC4 p or DC4 DC4 i.
If the PITCH LOCK option is set to YES in the EXTENDED SETUP
MODE, this command is ignored.
The default setting is “10 cpi x widthwise expansion”.
— 5. Bar code and enlarged character function —
5-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Enlarged character function
●
(12) VMI for enlarged characters: DC4 DC4 j
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
j
6A
106
n1 n2
n1 n2
n1
n2
Function: Specifies the VMI (vertical motion index) of enlarged
characters.
0
0
≤
≤
n1
n2
≤
≤
255
127
The VMI indicates the distance between two lines, i.e., the length the print
head moves after printing one line.
The VMI is (n1 + n2 x 256)/180”. The MSB of parameter n2 is masked.
The VMI can be set to zero.
The VMI is not dependent on the length expansion of enlarged characters.
After specifed command have priority over DC4 DC4 j or DC4 DC4 o.
The VMI is invalid and the cell offset 6 line feed pitch is selected (i.e., 1/6”
x cell expansion) by default.
(13) Setting and canceling the enlarged character mode: DC4 DC4 l
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
l
6c
108
n
n
n
Function: Sets and cancels the enlarged character mode.
n = 00H,30H:
01H,31H:
Cancels the enlarged character mode.
Sets the enlarged character mode.
The MSB of the parameter is masked. Any sequences other than the above
parameters are ignored.
When the enlarged character mode establish command is issued, the special
effects, character pitch, line feed pitch, length and width double-size
printing settings specified for the emulation become invalid the enlarged
character mode is canceled.
When the enlarged character mode starts, characters are printed in the
conditions selected when the enlarged character mode was last canceled.
If there are non-enlarged characters or bar codes when enlarge character
data is input the non-enlarged character are printed.
In the enlarged character mode, automatic printing is not performed if the
printing position exceeds the right margin. Excess data is abandoned and
the printing position is set at the right margin when the right margin is
exceeded.
If the right margin is exceeded while a single enlarged character is being
printed, the character is printed up to the right margin.
— 5. Bar code and enlarged character function —
5-22
Download from Www.Somanuals.com. All Manuals Search And Download.
Enlarged character function
●
(14) Enlarged character cell offset: DC4 DC4 o
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
o
6f
111
n
n
n
Function: Specifies the cell offset for enlarged characters.
255
0
≤
n
≤
This command specifies the cell offset for the enlarged characters in 1/180”.
The cell offset is used to execute a line feed (LF) command.
In the enlarged character mode, the line is fed by a pitch of (24 + cell
offset)/180” x cell expansion.
The VMI is invalid and the cell offset is 6 by default.
(15) Enlarged character pitch: DC4 DC4 p
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
p
70
112
n
n
n
Function: Specifies the pitch of enlarged characters.
n = 00H,30H:
01H,31H:
10 cpi
12 cpi
02H,32H:
Proportional
The MSB of the parameter is masked. Any sequences other than the above
parameters are ignored.
If the fixed pitch is selected, enlarged characters have the following width:
10 cpi: (18 × 180”) x widthwise expansion
12 cpi: (15 × 180”) x widthwise expansion
In the proportional mode, proportional characters are expanded by the same
ratio.
When the rotational angle for enlarged characters is set to 90 or 270 degrees,
characters other than graphic character are printed at a pitch of (24/180”) x
length expansion. If the PITCH LOCK option is set to YES in the
EXTENDED SETUP MODE, this command is ignored.
The HMI is invalidated and the character pitch is 10 cpi by default.
— 5. Bar code and enlarged character function —
5-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Enlarged character function
●
(16) Enlarged character quality: DC4 DC4 q
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
q
71
113
n
n
n
Function: Specifies the quality of enlarged characters as shown below.
n = 00H,30H:
01H,31H:
Standard quality
High-speed 1 quality
High-speed 2 quality
02H,32H:
The MSB of the parameter is masked. Any sequences other than the above
parameters are ignored.
The character quality is specified at the beginning of a line. If there is
character data on the line, this command is reserved and becomes valid on
the following line.
If the QUALITY LOCK option is set to YES in the EXTENDED SETUP
MODE, this command is ignored.
The standard quality is selected by default.
(17) Enlarged character rotational angle: DC4 DC4 r
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
r
72
114
n
n
n
Function: Specifies the rotational angle of enlarged characters as shown
below.
n = 00H,30H
01H, 31H
02H, 32H
03H, 33H
0°
90°
180°
270°
Enlarged characters are rotated counterclockwise.
The MSB of the parameter is masked. Any sequences other than the above
parameters are ignored.
Printing starts from the position specified with the DC4 DC4 a command
shown above.
Unless the rotational angle is set to 0 degree, no characters are underscored
even when underscores are input.
Pixels are printed at a rotational angle of 0 degree even if the rotational
angle is set to 90, 180, or 270 degrees.
This command is ignored if the PITCH LOCK option is set to YES in the
EXTENDED SETUP MODE and the length and width expansion values of
enlarged characters are different.
The default rotational angle is 0 degree.
— 5. Bar code and enlarged character function —
5-24
Download from Www.Somanuals.com. All Manuals Search And Download.
Enlarged character function
●
(18) Setting and canceling enlarged character smoothing: DC4 DC4 s
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
s
73
115
n
n
n
Function: Sets and cancels smoothing of enlarged characters.
n = 00H,30H:
01H,31H:
Cancels smoothing.
Sets smoothing.
The MSB of the parameter is masked. Any sequences other than the above
parameters are ignored.
Smoothing is set by default.
(19) Enlarged character top offset: DC4 DC4 t
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
t
74
116
m
m
m
n1
n1
n1
n2
n2
n2
Function: Specifies the top offset of enlarged characters.
m = (20)H
0
0
≤
≤
n1
n1
≤
≤
255
15
The top offset refers to the vertical distance between the top of the cell and
the top of a character. This determines the character position in the cell.
It is specified by (n1 + n2 x 256)/180”.
The high-order four bits of parameter n2 (bit 7 to bit 4) are masked.
The top offset is effective for only one characterafter this sequence.
The top offset is canceled when a line feed (LF) command, form feed (FF)
command, or vertical print position (DC4 DC4 y) command is issued.
The top offset is not dependent on the enlarged character arrangement.
It is always based on the top of the cell (corresponding to the ascender-
based position).
The top offset is not dependent on cell expansion or length expansion.
The bottom of a character (i.e., 24th pin position, regardless of character
type, even for a 30-dot pixel) does not extend beyond the bottom of the cell.
If the top offset is too large and the bottom of the character extends below
the bottom of the cell, the top offset is reduced.
Any sequences other than m = 20H are ignored.
— 5. Bar code and enlarged character function —
5-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Enlarged character function
●
(20) Setting and canceling underscores for enlarged characters: DC4 DC4 u
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
u
75
117
n
n
n
Function: Sets and cancels the underscore function.
n = 00H,30H:
01H,31H:
Cancels underscoring.
Specifies the underscoring.
The MSB of the parameter is masked. Any sequences other than the above
parameters are ignored.
An underscore is drawn on the 25th pin line at a thickness of (1 dot x length
expansion of the character).
No underscores are printed if the enlarged character rotational angle is not
set to 0 degree. Underscoring is off by default.
(21) Enlarged character width expansion: DC4 DC4 w
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
w
77
119
n
n
n
Function: Specifies the width expansion of enlarged characters.
127
0
≤
n
≤
The MSB of the parameter is masked.
If n is set to 0, the magnification specified in the setup mode is selected.
This command is ignored if the PITCH LOCK option is set to YES in the
EXTENDED SETUP MODE.
The expansion specified in the setup mode is set by default.
(22) Horizontal printing position for enlarged characters: DC4 DC4 x
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
x
78
120
m
m
m
n1
n1
n1 n2
n2
n2
Function: Specifies the horizontal position for printing enlarged
characters by (n1 + n2 x 256)/180” as shown below.
m = SP(20)H:
-(2D)H: Relative lefthand printing position
+(2B)H: Relative righthand printing position
Absolute printing position
0
0
≤
≤
n1
n2
≤
≤
255
15
The MSB of parameter m and the four high-order bits of n2 (bit 7 to bit 4)
are masked.
— 5. Bar code and enlarged character function —
5-26
Download from Www.Somanuals.com. All Manuals Search And Download.
Enlarged character function
●
If parameter m is different than shown above, this sequence is ignored.
The absolute print position is based on the left margin. If the specified
position exceeds the right margin, the print position is located at the right
margin.
If a relative lefthand printing position to the left of the left margin is
specified, left margin becomes the printing position.
If a relative righthand printing position to the right of the right margin is
specified, the right margin becomes the printing position.
The movement distance is not dependent on the width expansion of
enlarged characters.
(23) Vertical printing position for enlarged characters: DC4 DC4 y
Format:
ASCII
Hex
Decimal
DC4
14
20
DC4
14
20
y
79
121
m
m
m
n1 n2
n1 n2
n1 n2
Function: Specifies the vertical position for printing enlarged characters
by (n1 + n2 x 256)/180” as shown below.
m = SP(20)H:
-(2D)H: Relative reverse printing position
+(2B)H: Relative forward printing position
Absolute printing position
0
0
≤
≤
n1
n2
≤
≤
255
127
The MSBs of parameters m and n2 are masked. If parameter m is other
than shown above, this sequence is ignored.
The absolute print position is based on the TOF position. If the specified
position extends below the bottom margin, the bottom margin becomes the
print position.
If a relative reverse printing position exceeding the TOF position is
specified, the TOF position becomes the print position.
If a relative forward printing position that extends below the bottom margin
is specified, the print position is located at the bottom margin.
The movement distance is not dependent on the length expansion of
enlarged characters.
— 5. Bar code and enlarged character function —
5-27
Download from Www.Somanuals.com. All Manuals Search And Download.
●
Enlarged character function
Enlarged character print samples
This page shows examples of a BASIC program for printing enlarged
characters and the printed enlarged characters (actual size).
100 OPEN "LPT1:"AS #1
110 DC4$=CHR$(&H14)
120 '
130 PRINT #1, DC4$;DC4$;"@";
140 PRINT #1,DC4$;DC4$;"c";CHR$(8);
150 PRINT #1,DC4$;DC4$;"f";CHR$(4);
160 PRINT #1,DC4$;DC4$;"p";CHR$(1);
170 PRINT #1,DC4$;DC4$;"l";CHR$(1);
180 '
'
'
'
'
'
Initializing
Magnification of cell: x8
Font typeface: SCRIPT
Character pitch: 12 CPI
Magnification mode on
190 PRINT #1,"8";
'
Default size print
200 PRINT #1,DC4$;DC4$;"h";CHR$(2); ' Vertical magnification: x2
210 PRINT #1,DC4$;DC4$;"w";CHR$(2);
220 PRINT #1,DC4$;DC4$;"a";CHR$(3);
230 PRINT #1,"ASCE";
'
'
Horizontal magnification: x2
Alignment: ascender
240 PRINT #1,DC4$;DC4$;"a";CHR$(2);
250 PRINT #1,"CENT";
260 PRINT #1,DC4$;DC4$;"a";CHR$(1);
270 PRINT #1,"DESC";
280 PRINT #1,DC4$;DC4$;"a";CHR$(0);
290 PRINT #1,"BASE";
'
'
'
Alignment: center
Alignment: descender
Alignment: baseline
300 '
310 PRINT #1,DC4$;DC4$;"w";CHR$(8);
320 PRINT #1,"H";
330 PRINT #1,DC4$;DC4$;"w";CHR$(1);
340 FOR N=1 TO 8
350 PRINT #1,DC4$;DC4$;"h";CHR$(N);
360 PRINT #1,RIGHT$;(STR$(N),1); '
370 NEXT N
'
'
'
Horizontal magnification: x8
Horizontal magnification: x1
Vertical magnification: xn
380 PRINT #1,DC4$;DC4$;"w";CHR$(8); ' Horizontal magnification: x8
390 PRINT #1,DC4$;DC4$;"r";CHR$(1); Rotate: 90 degree
400 PRINT #1, "R"
'
;
410 PRINT #1,CHR$;(13);CHR$(10); ' CR+LF
420 '
430 PRINT #1,DC4$;DC4$;"l";CHR$(0);
440 CLOSE #1
'
Magnification mode off
450 END
— 5. Bar code and enlarged character function —
5-28
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
6.
When the printer is used for continuous printing, its protective function may be
invoked to prevent malfunctions. If the printer does not recover from a functional
error, please contact the dealer.
Functional error messages (displayed on the LCD)
When a funtional error occurs, the ERROR lamp blinks and
the buzzer sounds for five seconds. In this case, turn off the
power once and remove the cause of the error.
CARRIAGE ERROR
CARRIAGE ERROR
• The print head is not in place.
Check whether the ribbon or paper was caught by the
print head. Recheck the paper thickness adjustment.
NO LCD DISPLAY
The error lamp blinks and the
buzzer sounds immediately
after turning the power on or
after the printer is reset.
INTERNAL RAM ERROR
• An error occurred in the internal RAM.
Turn off the power and then turn it back on. If the print-
er does not recover from the error, contact the dealer.
FAN ERROR
FAN ERROR
• The fan for cooling the internal circuits stopped.
Turn off the power, then turn it back on. If the printer
does not recover from the error, contact the dealer.
F.S. ERROR
F.S. ERROR
• An error occurred in the paper ejection mechanism.
Detach the rear cover, and check whether or not paper is jammed
in the paper ejection mechanism in the back of the printer.
Remove any paper, turn off the power, and turn it on again. If the
printer does not recover from the error, contact the dealer.
T.S. ERROR
T.S. ERROR
• An error occurred in the paper path switching mechanism.
Remove all paper. Turn the power on and off several
times.
Turn off the power and then turn it back on. If the printer
does not recover from the error, contact the dealer.
HAI.S. ERROR
HEAD ADJUSTMENT ERROR 1
• The print head was not adjusted to the standard position after head
adjustment motion.
Turn off the power and then turn it back on. If the
printer does not recover from the error, contact the
dealer.
— 6. Troubleshooting —
6-1
Download from Www.Somanuals.com. All Manuals Search And Download.
G Error messages and countermeasures
HA.S. ERROR
HEAD ADJUSTMENT ERROR 2
Contact of the print head with the platen or paper when the print head
moved from the standard position toward the platen during head
adjustment was not confirmed.
•
Turn off the power then turn it back on. If the printer
does not recover from the error, contact the dealer.
HOME S. ERROR
HOME SENSE ERROR
• The home position cannot be detected properly when home sensing is
executed.
Check whether the ribbon or paper has been caught by
the print head. Recheck the paper thickness adjustment.
PLEASE POWER OFF
ABNORMAL CURRENT ERROR
• An abnormal current was detected.
The printer is automatically turned off after five
seconds. Stop using the printer, and contact the dealer.
Operational error messages (displayed on the LCD)
PRINT HEAD COOLING
The print head is being cooled to prevent it from overheating.
The ONLINE lamp blinks.
HEAD PROTECTION
•
The print head has become too hot during high-density
printing. When this message is displayed, the printing
speed is reduced or printing stops. When the print head
temperature drops, the printer restarts printing.
PAPER PARK ERROR
This error message indicates that fanfold paper is not being retracted
properly. The ERROR lamp blinks, the buzzer sounds three times,
and the printer enters the offline state.
PARK ERROR
•
Check whether paper is jammed in the paper ejection
mechanism. This error occurs when paper that cannot
be retracted though reverse feeding motion is printed
for approximately three pages. If three pages or more
have been printed, keep the REVERSE LF key depressed
to move back the paper.
— 6. Troubleshooting —
6-2
Download from Www.Somanuals.com. All Manuals Search And Download.
G Error messages and countermeasures
Front Tractor
OUT-OF-PAPER ERROR
•
This error message indicates that paper feeding has failed in the CSF
mode or that no paper is set in the fanfold paper or manual paper
loading mode. The ERROR lamp lights, the buzzer sounds for one
second, and the printer enters the offline state.
PAPER OUT: F.TR.
Rear Tractor
The ONLINE, PAPER PATH, EJECT/LOAD, FORM FEED, LINE
FEED and other keys are effective. Resetting is also effective.
PAPER OUT: R. TR.
Manual
ONLINE key
If there is still print data, paper is fed. If paper is fed properly,
the out-of-paper condition is reset and the printer enters the
online state. If paper is not fed properly, the printer remains in
the out-of-paper condition.
SET PAPER
CSF
If there is no print data, the out-of-paper condition is
reset and the printer enters the online state.
PAPER OUT: CSF
PAPER PATH key
Press the PAPER PATH key to change the paper path.
The out-of-paper condition is reset and the printer
enters the online state.
EJECT/LOAD, FORM FEED and LINE FEED
keys
If paper is fed properly, the no-paper condition is reset
and the printer enters the previous (online or offline )
state.
If manual feeding is selected, paper is fed only
when the paper sensor detects paper. Paper is not fed
by pressing the key.
PAPER JAM ERROR
Front Tractor
• This error occurs when fanfold paper is not fed properly, manually-
loaded or CSF-loaded paper is not ejected properly, or paper is not
properly manually loaded from the front or rear. The ERROR lamp
lights, and the buzzer sounds three times.
PAPER JAM : F.TR.
Rear Tractor
PAPER JAM : R.TR.
When paper insertion has failed
SET PAPER AGAIN
When paper ejection has failed
REMOVE PAPER
The LINE FEED and REVERSE LF keys are effective.
Remove jammed paper using these keys or by hand.
The ONLINE key is also effective. When "PAPER JAM"
is displayed, pressing the ONLINE key will clear the
error status.
The paper jam sensor may not function properly if the
sensor is exposed to a direct light or sunlight.
— 6. Troubleshooting —
6-3
Download from Www.Somanuals.com. All Manuals Search And Download.
G Error messages and countermeasures
SKEW ERROR
PAPER IS SKEWED
•
This error occurs if the printer detects that cut sheet paper was loaded
on the skew manually. The ERROR lamp blinks, and the buzzer
sounds three times. The paper is ejected and the printer enters the
offline state.
Load paper again. If it is loaded straight, the printer
enters the online state.
COVER OPEN ERROR
This error occurrs if the front cover is opened. The ERROR lamp
lights, and the ONLINE lamp blinks.
FRONT COVER OPEN
•
Closing the front cover will remove the cause of this
error. The printer is in the offline state while the cover
is opened.
Single Sheet Top Out
OPEN TOP COVER
Single Sheet Top Out
PAPER PATH ERROR
•
This error occurs in paper feeding if the cover that should be opened is
not open or the cover that should be closed is not closed. The ERROR
lamp lights, and the buzzer sounds three times, and the printer enters
the offline state.
CLOSE REAR COVER
Fanfold Top Out
The printer is recovered from this error and enters the
previous online or offline state by opening or closing the
cover, properly according to the message displayed on
the LCD.
OPEN REAR COVER
Single Sheet or Rear Tractor
OPEN PAPER RACK
H.ADJ: FIX ERROR
HEAD ADJUSTING ERROR
•
This error occurs if the print head contacts the paper but cannot move
to the specified position after paper is loaded in the fixed paper
thickness mode. The ERROR lamp lights, and the buzzer sounds
three times, and the printer enters the offline state.
These messages are
displayed alternately at 3
second interval.
The current HEAD ADJUSTMENT setting is dispalyed
by pressing the SET UP key. Change the click position
PRESS SETUP
with the
or
key and press the ENTER key to
move the print head to the currently set position. If the
print head moves properly, the printer will enter the
offline state. If the print head fails to move properly, the
error message reappears.
FIX: +10CLICK
— 6. Troubleshooting —
6-4
Download from Www.Somanuals.com. All Manuals Search And Download.
G Error messages and countermeasures
REMOVE REAR PAP.
FLAP SWITCHING ERROR
•
This error occurs if the flap is not located at the proper position.
The ERROR lamp lights, and the buzzer sounds three times, and the
printer enters the offline state.
These messages are
displayed alternately at 3
second interval.
Any keys are ignored except the ONLINE key. When the
rear paper is removed and the ONLINE key is pressed,
the paper path is changed. When this operation is
completed properly, the printer enters the previous
online or offline state.
PRESS ONLINE SW
JAM.S LEVEL ERR
JAM SENSOR ERROR
The jam sensor was found defective when loading fanfold paper.
The ERROR lamp lights, and the buzzer sounds three times, and the
printer enters the offline state.
•
Press the ONLINE key to recover the printer from this
error. The paper jam detection function is disabled.
Remove paper dust from the jam sensor, and load
fanfold paper again.
— 6. Troubleshooting —
6-5
Download from Www.Somanuals.com. All Manuals Search And Download.
G Troubleshooting
Symptoms
Cause and Solution
• Power cord not connected.
• Malfunction of the power supply in the
printer
POWER lamp fails to
light.
See page 1-1.
See page 6-3.
Contact the dealer.
• The paper sensor is clogged by paper dust.
Clean the paper sensor.
• Malfunction of the paper sensor
Contact the dealer.
Error lamp does not
light.(Out-of-paper
error not detected.)
• The print head has overheated.
Wait until it has cooled down.
Printer stops or slows
down on printing.
See page 6-3.
See page 3-9.
• Head adjustment is not set correctly. (*1)
• The print head may need to be replaced.
• Ribbon cassette may need to be replaced.
Poor quality printing
See page 3-9.
See page 1-2.
Smudging of the paper
• Head adjustment is not set correctly. (*1)
• Ribbon cassette is not properly installed.
• The print head may need to be replaced.
• Check whether the cable connection is faulty
or broken.
• Host system control and data code may not
match the printer's setup.
Incorrect character
printed
• Check the emulation setting of the EXTENDED
SETUP MODE.
• Adjust with the vertical alignment function.
• The print head may need to be replaced.
See page 4-6.
Print position gap
occurs over bar code
or vertical line.
• Stack of fanfold paper to be fed is placed
beside the printer crookedly.
Fanfold paper slips
See page 1-12.
See page 3-27.
• The automatic carriage return option in the
extended setup options is set incorrectly.
• Change the setting of #27 CR SETTING on
the EXTENDED SETUP MODE.
Extra line feed
*1) When the head adjustment is not appropriate,
(1) In the AUTO mode:
Specify the appropriate head adjustment again in the range from -2 to +5. When the appropriate
head adjustment cannot be set, carry out this setting in the FIX mode.
(2) In the FIX mode:
Specify the appropriate head adjustment again.
(3) When the appropriate head adjustment cannot be specified, the head adjustment mechanism is
faulty. Have it replaced by the dealer.
— 6. Troubleshooting —
6-6
Download from Www.Somanuals.com. All Manuals Search And Download.
G Troubleshooting
Symptoms
Cause and Solution
• Paper is curled. Carefully remove the jammed
paper.
Paper jam
• Head adjustment is not set correctly. (*1)
• Push down the lock lever of tractors to the
LOCK position.
• When using the printer in an environment
where it is exposed to a direct light or
sunlight, make sure that the paper jam sensor
is not directly exposed to the light.
• There is some obstruction in the paper path or
ejection path.
• The paper jam sensor is clogged by paper
dust. Clean the paper jam sensor. (*2)
• Malfunction of the paper jam sensor
Contact the dealer.
See page xiii.
See page 3-44.
Paper jam is not
detected.
• Paper jam detection is set to NO in the
EXTENDED SETUP MODE. Change the
setting of #65 PAPER JAM DETECTION.
Paper is skewed.
• The skew sensor is clogged by paper dust.
Clean the skew sensor. (*2)
See page xiii.
• Malfunction of the skew sensor
Contact the dealer.
• Skew detection is set to NO in the
EXTENDED SETUP MODE. Change the
setting of #64 SKEW DETECTION.
See page 3-43.
See page 6-1.
Skewing is not
detected.
• Turn the power on and off several times.
• Malfunction of the flap mechanism
Contact the dealer.
Flap will not change
Tractor mode cannot
be changed
• Turn the power on and off several times.
• Malfunction of the tractor mechanism
Contact the dealer.
See page 6-1.
See page 3-42.
• The paper ejection path is not set properly.
Set the proper ejection path using the PAPER
PATH key or #61 PAPER PATH on the
EXTENDED SETUP MODE.
Paper is not ejected
to the top.
• Upward ejection cannot be used when paper
that has a short page length (150 mm or less)
is being used.
*2) How to clean the paper jam sensor and skew sensor cover
After switching the power off, remove the ink ribbon and clean these sensors using a vacuum
cleaner or cotton-swab.
— 6. Troubleshooting —
6-7
Download from Www.Somanuals.com. All Manuals Search And Download.
7. I
nterface specifications
Parallel interface
Input connector (36-pin parallel )
18171615 1413121110 9
8
7
6
5
4
3
2
1
36353433 3231302928272625242322212019
Pin configuration
PIN
1
2
3
4
5
6
7
8
SIGNAL
STROBE *
DATA 1
DATA 2
DATA 3
DATA 4
DATA 5
DATA 6
DATA 7
DATA 8
ACK *
IN/OUT
IN
PIN
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
SIGNAL
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
INITIAL *
ERROR *
GND
IN/OUT
IN
IN
IN
IN
IN
IN
IN
IN
OUT
OUT
OUT
OUT
IN
9
10
11
12
13
BUSY
PE
SELECT
IN
OUT
14 AUTO FEED *
15
16
17 GHASSIS GND
18 +5V
NC
GND
NC
HIGH
SELECT IN *
OUT
IN
OUT
(1) The signals marked with asterisks are negative logic signals.
(2) The High level is raised to +5 V with a 2.2 kΩ resistor.
(3) NC means "not connected".
(4) The CHASSIS GND and GND are connected inside the
printer.
Bidirectional (IEEE1284. Nibble mode) is available.
— 7. Interface specifications —
7-1
Download from Www.Somanuals.com. All Manuals Search And Download.
G Parallel interface
Data Input
Timing chart
TROBE
ATA 1~8
BUSY
ACK
1µs
(MAX)
0µs
(MIN)
4~6µs 4~6µs
1µs
(MIN)
1~50µs
1µs
(MIN)
7~10µs
Initialization
INITIAL
BUSY
ACK
50µs
(MAX)
4~6µs 4~6µs
50µs(MIN)
7~10µs
Input/output conditions
Output Signals
Input Signals
+5V
+5V
• BUSY
• ACK
• DATA1 ~ DATA8
• AUTO FEED
• PE
• ERROR
• SELECT IN
2.2K Ω
2.2K Ω
• SELECT
Output
Terminal
Input Terminal
To printer
To printer
(7406,7407
or equivalent)
(74LS04
or equivalent)
+5V
• STROBE
2.2K Ω
100 Ω
Input Terminal
To printer
(74LS14
or equivalent)
330pF
+5V
• INITIAL
2.2K Ω
100 Ω
Input Terminal
To printer
(74LS14
or equivalent)
1000pF
All signals are TTL-level signals.
At the input terminals
of the printer
HIGH LEVEL
LOW LEVEL
2.4 ~ 5.0 V
0 ~ 0.4 V
— 7. Interface specifications —
7-2
Download from Www.Somanuals.com. All Manuals Search And Download.
G Parallel interface
Signal explanations
Input signals to the printer
[DATA1 to DATA8]
Each of these signals is an 8-bit data signal. It is high
when the signal is logic 1 and low when the signal is
logic 0. DATA1 is the LSB, and DATA8 is the MSB.
See page 3-53.
[STROBE]
This is a strobe signal for reading an 8-bit data signal.
Data is read in at the falling or rising edge of the
STROBE signal.
See page 3-53.
[INITIAL]
This signal initializes the printer to the state in which the
printer starts up when the power is turned on. It is
normally high. When it is set to low, the printer is reset.
When it is set to high again, the printer is initialized.
[AUTO FEED]
If this signal is set to low when #27 CR SETTING is set
to AUTOFEED in the EXTENDED SETUP MODE, line
feeding is performed when the CR command is executed.
In the HP mode or IBM mode, it is possible to specify
whether to perform line feeding after executing the CR
command by using the software command, regardless of
the settings of this signal and #27 CR SETTING in the
EXTENDED SETUP MODE.
See page 3-29.
[SELECT IN]
When this signal is set to high, the control code is
validated. Validity of this signal is specified in the
extended setup mode. In the HP mode, this signal setting
is ignored.
See page 3-47.
Each signal wire must be 2 meters or less in
length. It is recommended that a twisted pair
of signal and GND wires be used.
— 7. Interface specifications —
7-3
Download from Www.Somanuals.com. All Manuals Search And Download.
G Parallel interface
Output signals from
the printer
[BUSY]
This signal indicates that the printer is in the busy state.
While it is high, no external data is accepted.
This signal is set to high in any of the following cases:
(1) Initialization is being performed.
(2) The STROBE signal is issued and data is input.
(3) The self-test printing is being performed.
(4) The printer is in the offline state.
(5) The printer cover is open.
(6) The printer is in an error state.
[ACK]
[PE]
This signal is output at the falling edge of the BUSY
signal which was set high by the STROBE signal. No
ACK signal is output in cases (4), (5), (6) above.
See page 3-53.
This signal is set high when no paper is detected. It is set
low when paper is detected.
[ERROR]
This signal is set low when an out-of-paper error or other
error occurs in the IBM mode.
It is set low when printer is in the offline state, in
addition to the errors noted above, in the EPSON mode.
This signal is set low when the functional error occurs in
the HP mode.
See page 6-3.
[SELECT]
This signal is always set high in the EPSON mode.
In the IBM mode, it is set low when an out-of-paper
error, paper error or functional error occurs, the printer
cover is opened, the printer is in the offline state, or the
deselect command (ESC + Q + (23)H or (B9)H) is
executed. It is set high when the printer is in the online
state with the ONLINE key or the DC1 (select) command
is executed.
In the HP mode, this signal is set low when the printer is
in the offline state. It is set high when the printer is in
the online state.
When #84 ERROR STATUS is set to NO in the
EXTENDED SETUP MODE, PE signal is always set to low
and ERROR and SELECT signals are always set to high.
— 7. Interface specifications —
7-4
Download from Www.Somanuals.com. All Manuals Search And Download.
G Serial interface
Serial interface
Input connector (25-pin serial connector)
13 12 11 10 9
8
7
6
5
4
3
2
1
25 24 23 22 21 20 19 18 17 16 15 14
Pin configuration
PIN
SIGNAL
IN/OUT
PIN
SIGNAL IN/OUT
1
2
3
4
5
6
7
8
9
10
11
12
13
CHASSIS GND
14
15
16
17
18
19
20
21
22
23
24
25
NC
NC
NC
NC
NC
NC
DTR
NC
NC
NC
NC
NC
TXD
RXD
RTS
CTS
DSR
OUT
IN
OUT
IN
IN
SIGNAL GND
CD
OUT
IN
NC
NC
SRTS
NC
NC
OUT
(1) NC means "not connected".
(2) The CHASSIS GND and SIGNAL GND are connected inside
the printer.
Input/output conditions
Input signal
(75189 or equivalent)
INPUT
To printer
330pF
Output signal
OUTPUT
(75188 or equivalent)
To printer
Signal levels
OFF: Indicates "MARK" at a level from -3 to -15 V.
ON: Indicates "SPACE" at a level from +3 to +15 V.
— 7. Interface specifications —
7-5
Download from Www.Somanuals.com. All Manuals Search And Download.
G Serial interface
Input signals to the printer
[RXD (Receive data)]
Serial input data, which consists of a start bit, data bits,
(parity bit), and stop bit.
The data length (7 or 8 bits), use of the parity bit, and
even or odd parity are specified in the EXTENDED
SETUP MODE.
See pages 3-47 and 3-48.
[CTS (Clear to send)]
A data transmission control signal, which indicates that
data can be sent to the computer.
Whether or not to use this signal to control data
transmission is specified in the setup mode. This signal
is not used by default.
If the X-ON/X-OFF or ETX/ACK protocol is selected
and the CTS ENABLE option is set to NO in the
EXTENDED SETUP MODE, the printer outputs data to the
computer, regardless of this signal setting.
If the X-ON/X-OFF or ETX/ACK protocol is selected
and the CTS ENABLE option is set to YES in the
EXTENDED SETUP MODE, the printer outputs data to the
computer according to this signal setting.
See page 3-50.
[DSR (Data set ready)]
This signal indicates the state of the modem or computer.
If data is sent to the printer when this signal is ON, the
data is processed as valid data.
Data received when this signal is OFF is ignored as
invalid data.
By default, this signal is not used, and all data sent by the
computer is processed as valid data (i.e., the default
setting causes the same operation as when the DSR
signal is ON). Whether or not to use this signal for
control is selected in the EXTENDED SETUP MODE.
See page 3-51.
— 7. Interface specifications —
7-6
Download from Www.Somanuals.com. All Manuals Search And Download.
G Serial interface
[CD (Carrier detect)]
This signal indicates whether the modem is connected
with the communication line. If data is sent to the printer
when this signal is active, the data is processed as valid
data. Data received when this signal is inactive is
ignored as invalid data.
By default, this signal is not used, and all data sent by the
computer is processed as valid data (i.e., the default
setting causes the same operation as when the CD signal
is active). Whether or not to use this signal for control is
selected in the EXTENDED SETUP MODE.
See page 3-51.
Output signals from the printer
[TXD (Transmit data)]
Serial output data.
X-ON, X-OFF and ACK signals are output.
The data format is the same as the received data format.
[RTS (Request to send)]
Always held active (space).
[SRTS]
This signal indicates that the printer is ready or busy.
OFF : Indicates that the printer is busy and printer is in
the offline state. Data transmission to the printer is
disabled.
ON : Indicates that the printer is ready and data can be
transmitted to the printer.
This signal is always ON when X-ON/X-OFF( Ι )or( Π )or
the ETX/ACK protocol is selected.
[DTR (Data terminal ready)]
This signal indicates that the printer is ready or busy.
OFF: Indicates that the printer is busy and printer is in the
offline state. Data transmission to the printer is
disabled.
ON: Indicates that the printer is ready and data can be
transmitted to the printer.
This signal is always ON when X-ON/X-OFF (I) or (II) or
the ETX/ACK protocol is selected.
— 7. Interface specifications —
7-7
Download from Www.Somanuals.com. All Manuals Search And Download.
G Serial interface
Handshaking protocol
Any of four handshaking protocols is selected in the
extended setup mode.
- DTR protocol
See page 3-49.
- X-ON/X-OFF (I) protocol
- X-ON/X-OFF (II) protocol
- ETX/ACK protocol
Control of these serial protocols is based on the free area in the data
buffer. There are two protocol control points based on the data buffer:
CIN, where the ready state changes to the busy state, and CRN, where
the busy state changes to the ready state. The values of these points are
shown below.
When 512KB or 8KB buffer size is selected,
CIN: 1KB
CRN: 2KB
When 128-byte buffer size is selected,
CIN: 32 bytes
CRN: 64 bytes
When the free space in the data buffer is reduced below the CIN value,
the printer enter the busy state and remains there until the free space
exceeds the CRN value. When the free space exceeds the CRN value,
the printer enters the ready state.
DTR (READY/BUSY) Protocol
In this protocol, the printer state is indicated by the SRTS signal
(pin No. 11) and DTR signal (pin No. 20).
When the printer is ready, each signal goes ON (+12 V). When
the printer is busy or in the offline state, each signal goes OFF
(-12 V).
When the printer is busy or in the offline state, the computer does
not send data.
However, data from the computer can be received when the
printer is busy or in the offline state.
(1) When the power is turned on,
The SRTS and DTR signals go ready when data input is
enabled on completion of initialization after turning on
the power.
— 7. Interface specifications —
7-8
Download from Www.Somanuals.com. All Manuals Search And Download.
G Serial interface
X-ON/X-OFF (I)/(II) protocol
In this protocol, the printer sends the X-ON(11)H and X-
OFF(13)H codes to the computer to indicate the printer state.
In the X-ON/X-OFF protocol, the printer sends X-OFF(13)H to
the computer once when the ready state changes to the busy or
offline state, once when 64 bytes of data have been received
since this point in time, and once when the free area in the buffer
becomes zero.
The printer sends X-ON(11)H once to the computer when the
busy or offline state changes to the ready state or the power is
turned on. If the ONLINE key is pressed in the offline state and
the free space in the buffer is greater than the CIN value, the
printer sends X-ON and enters the ready state. If the free space
in the buffer is less than the CIN value, the printer enters the busy
state without any operation. In the busy or offline state, the
SRTS and DTR signals remain active. X-ON and X-OFF signals
are sent to the computer even if the DSR or CD input signal is
inactive. In the X-ON/X-OFF (I) protocol, the X-ON signal is
sent when the power is turned on. In the X-ON/X-OFF (II)
protocol, the X-ON signal is not sent when the power is turned
on.
The X-OFF signal is sent once in any of the following conditions:
(1) The ready state changes to the busy state.
(2) The ready state changes to the offline state.
(3) 64 bytes of data are received in the state shown in (1) or
(2) above, provided the free area in the buffer is greater
than 64 bytes.
(4) The free area in the buffer becomes zero, regardless of the
online or offline state.
The X-ON signal is sent once in any of the following conditions:
(1) The busy state changes into the ready state.
(2) The offline state changes into the online state.
(3) The printer enters the online state when power is turned
on, provided the X-ON/X-OFF (I) protocol is selected.
— 7. Interface specifications —
7-9
Download from Www.Somanuals.com. All Manuals Search And Download.
G Serial interface
Special notes
(1) If the ONLINE key is pressed in the offline state and the
free area in the buffer is over the CIN value,
1) The printer sends X-ON and enters the online ready
state if it was in the ready state.
2) The printer sends no signal and enters the online busy
state if it was in the busy state.
(2) If the ONLINE key is pressed in the offline state and the
free area in the buffer is less than the CIN value, the printer
sends no signal and enters the online busy state.
(3) If the ready state is changed into the offline state by pressing
the ONLINE key and data is input and the free area in the
buffer exceeds the CIN value during data input even though
the printer has sent X-OFF once, the printer does not send
X-OFF.
However, if the printer receives the 64th byte of data after
entering the offline state, it sends X-OFF once.
(4) The printer sends X-OFF once if the printer enters the
offline state due to an out-of-paper error after initialization.
(5) In the X-ON/X-OFF (I) protocol, X-ON is output after
power on when initialization is completed and the printer
enters the online state.
POWER ON
<ON>
[OFF]
READY
(OFF)
(OFF)
[ON]
(ON)
(ON)
<OFF>
{OFF}
(X)
BUSY
ON-LINE
OFF-LINE
(X)
(X)
(X)
<OFF>
0
CIN
FULL
CRN
[ON][OFF]
(ON), (OFF)
{OFF}
: X-ON or X-OFF is sent once when the data size
changes.
: X-ON or X-OFF is sent once when the ONLINE
key is pressed.
: X-OFF is sent when the 64th byte of data is
received after sending X-OFF.
<OFF>
: X-OFF is sent when the free area in the buffer
becomes zero.
: X-ON is sent when power is turned on and the
X-ON/X-OFF (I) protocol is in use.
: No signal is sent. Status transition due to change
in the amount of data.
<ON>
: Status transition caused by pressing the ONLINE key.
— 7. Interface specifications —
7-10
Download from Www.Somanuals.com. All Manuals Search And Download.
G Serial interface
ETX/ACK protocol
Upon reception of ETX(03)H, the printer sends ACK(06)H to the
computer to indicate that it is ready. If the printer is busy, it does
not send ACK to indicate that it is busy.
If the free area in the buffer is less than the CIN value when the
printer receives ETX, the printer does not send ACK
immediately. It sends ACK when the free area in the buffer
becomes greater than the CRN value. If the printer is in the
offline state, the printer sends ACK when the ONLINE key is
pressed and the printer becomes ready.
In the busy or offline state, the SRTS and DTR signals remain
ON. The printer sends ACK to the computer even if the CTS
input signal is OFF.
The interface does not analyze the (03)H code. Thus, the printer
sends ACK in response to (03)H received in an escape sequence
or graphic data sequence. The received (03)H code is sent to the
emulation as normal data.
Baud rate
The baud rate can be selected from the values shown below in the
extended setup mode:
38400BPS, 19200BPS, 9600BPS, 4800BPS,
2400BPS, 1200BPS,
600BPS,
300BPS,
See page 3-49.
Serial data organization
The data frame has the following organization.
START BIT (1) + DATA BIT (7 or 8) + PARITY BIT (0 or 1) + STOP
BIT (1 or 2)
MARK: Logic "1" (-3 to -15 V)
SPACE: Logic "0" (+3 to +15 V)
+3
-3
+15V
D2
D1
D3 D4 D5 D6 D7 D8
STOP
-15V START
Automatic serial/parallel selection
If #70 INTERFACE is set to AUTO in the EXTENDED SETUP MODE, the serial or parallel
interface is selected automatically.
In the initial condition, both the serial and parallel interfaces are ready. When data is input
through either interface, printing is done through that interface. In printing, the other interface is
in the busy state. If data is input through the busy interface, the data is ignored.
If no data is input to the first interface, both interfaces are reset to the initial ready state.
— 7. Interface specifications —
7-11
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Software commands
Code
Symbol
Function
Decimal
(07)D
Hex
(07)H
Activates the printer buzzer.
BEL
BS
HT
LF
Moves the printing position leftward by one character.
Moves the printing position to the next horizontal tab.
Single line feed
(08)D
(09)D
(10)D
(08)H
(09)H
(0A)H
Causes a carriage return if #28 LF SETTING is set to CR + LF in
the EXTENDED SETUP MODE.
VT
FF
CR
(11)D
(12)D
(13)D
(0B)H
(0C)H
(0D)H
Vertical tab
Causes a carriage return if #28 LF SETTING is set to CR + LF in
the EXTENDED SETUP MODE.
Form feed
Causes a carriage return, regardless of the setting in the
EXTENDED SETUP MODE.
Carriage return
Executes a line feed after a carriage return if #27 CR SETTING
is set to CR + LF or #27 CR SETTING is set to AUTOFEED and
the parallel AUTO FEED signal is low.
SO
SI
(14)D
(15)D
(0E)H
(0F)H
Double-width printing on a single line.
Specifies condensed mode (from 10 cpi to 17 cpi, 12 cpi to 20 cpi, or
proportional to condensed proportional). Valid only when #34
PITCH LOCK is set to NO in the EXTENDED SETUP MODE.
Printer select
DC1
(17)D
(11)H
Cancels the input data ignoring condition which is set by the DC3
(deselect) code. Valid when #71 SELECT IN ENABLE is set to 1
in the EXTENDED SETUP MODE or SELECT IN ENABLE is
selected to I/F and the SELECT IN signal is high.
Cancels condensed mode.
DC2
DC3
(18)D
(19)D
(12)H
(13)H
Printer deselect
Puts the printer into the deselect state. Valid when #71 SELECT
IN ENABLE is set to 1 in the EXTENDED SETUP MODE or
SELECT IN ENABLE is selected to I/F and the SELECT IN
signal is high.
DC4
CAN
(20)D
(24)D
(14)H
(18)H
Cancels the double-width mode established by the SO command.
Cancel
Clears all data in the print buffer and printing position specified
with the horizontal position move command (HT, ESC $, ESC \,
etc.).
DEL
ESC
(127)D
(27)D
(7F)H
(1B)H
Deletes a character.
Designates ESC sequence.
ESC SO
ESC SI
ESC EM (27)D(25)D
(27)D(14)D
(27)D(15)D
(1B)H (0E)H Double-width printing on a single line.
(1B)H (0F)H Specifies condensed mode.
(1B)H (19)H Specifies the paper path.
n
n
n
n="R" : Ejects paper.
n="B" : Feeds paper with the rear tractor.
n="F" : Feeds paper with the front tractor.
n="M" : Feeds manually loaded paper.
n="f" : Ejects paper to the front.
n="t" : Ejects paper to the top.
n="r" : Ejects paper to the rear.
8. Software commands
—
—
8-1
Download from Www.Somanuals.com. All Manuals Search And Download.
● EPSON Software commands
Code
Symbol
Function
Decimal
Hex
ESC SP
n
(27)D(32)D
n
(1B)H (20)H
n
Specifies the space between characters.(0 ≤ n ≤ 127)
The dot density differs with the printing mode, as shown below.
Printing mode
Draft
LQ
Dot pitch
1/120 inch
1/180 inch
1/180 inch
Proportional
ESC !
n
(27)D(33)D
n
(1B)H (21)H
n
Batch selection of the printing mode (0 ≤ n ≤ 255)
Command having
same function
Bit
"1"
"0"
0
12 cpi
Proportional
Condensed
Emphasized
Double strike
Double-width
Italic
10 cpi
ESC M / ESC P
ESC p
SI / DC2
ESC E / ESC F
ESC G / ESC H
ESC W
ESC 4 / ESC 5
ESC -
1
2
3
4
5
6
7
Proportional canceled
Condensed canceled
Emphasized canceled
Double strike canceled
Double-width canceled
Italic canceled
Underscoring selected
Underscoring canceled
ESC #
ESC $
n1 n2
ESC %
n
(27)D(35)D
(27)D(36)D
n1 n2
(27)D(37)D
n
(1B)H (23)H
(1B)H (24)H
n1 n2
(1B)H (25)H
n
Cancels MSB control.
Specifies the absolute printing position.
Distance = n1 + ( n2 × 256 ) (In units of 1/60 inch)
Specifies or cancels the down-load character set.(n = 00, 01, 30, 31)
n = 01, 31: Specifies the down-load character set.
n = 00, 30: Cancels the down-load character set.
Defines the down-load characters.
ESC &
s, n, m,
[ a0, a1,
a2, data]
m-n+1
(27)D(38)D
s, n, m,
[ a0, a1,
a2, data]
m-n+1
(1B)H (26)H
s, n, m,
[ a0, a1,
a2, data]
m-n+1
s:
n :
m :
a0 :
a1 :
a2 :
Down-load character set number
Define start of ASCII code (00)H ~ (7F)H
Define end of ASCII code (00)H ~ (7F)H
Left space
Actual character width (Number of dots)
Right space
ESC *
m
n1 n2
d1 d2
•••dk
(27)D(42)D
m
n1 n2
d1 d2
••• dk
(1B)H (2A)H
m
n1 n2
d1 d2
••• dk
Selects graphic function.
8-pin graphic: n1 + (n2 × 256)
24-pin graphic: (n1 + (n2 × 256))
×
3
Horizontal dot density
(dot/inch)
Mode
Pin
m
Max. dots per line
Single-density
Double-density
Double-speed
double-density●
8
8
8
0
1
2
60
120
120
816
1632
1632
Quadruple-density ●
CRT I
CRT II
Single-density
Double-density
CRT III
Triple-density
Hex-density●
8
8
8
24
24
24
24
24
3
4
6
240
80
90
60
120
90
3264
1080
1224
816
1632
1224
2488
4896
32
33
38
39
40
180
360
●
Horizontally adjacent dots can not be printed.
In the 8-pin graphic mode, one bit of data corresponds to two print head pin dots, as shown below.
Data
MSB
●
●
●
●
●
●
●
●
LSB
↓
↓
↓
↓
↓
↓
↓
↓
Print head pin Top
● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● Bottom
8. Software commands
—
—
8-2
Download from Www.Somanuals.com. All Manuals Search And Download.
● EPSON Software commands
Code
Symbol
Function
Decimal
Hex
ESC ( -
n1 n2
m
(27,40,45)D
n1 n2
m
(1B,28,2D)H
n1 n2
m
Specifies line type. ( n1 = 3 ) ( n2 = 0 ) ( m = 1 )
d1 = 1 Underscore d2 = 1 Single line
d1 = 2 Center line d2 = 2 Double lines
d1 = 3 Upper line d2 = 5 Single dotted line
d2 = 6 Double dotted lines
d1 d2
d1 d2
d1 d2
d2 = 0 Cancels the line specification.
ESC ( ^
n1 n2
ESC ( t
n1n2
d1 d2
d3
(27,40,94)D
n1 n2
(27,40,116)D
n1 n2
d1 d2
d3
(1B,28,5E)H
n1 n2
(1B,28,74)H
n1 n2
d1 d2
d3
All-character set.
Prints n1 + n2 x 256 characters in the all-character character set.
Specifies a character set.
d1 : Displays ESC t n command table No.
d2, d3 : Specifies the character set.
d2 = 0, d3=0 : ITALIC
d2 = 1, d3=0 : PC-437
d2 = 3, d3=0 : PC-850
d2 = 7, d3=0 : PC-860
d2 = 8, d3=0 : PC-863
d2 = 9, d3=0 : PC-865
d2 = 11, d3=0 : PC-857
d2 = 44, d3=0 : PC-858
d2 = 24, d3=0 : PC-861
d2 = 25, d3=0 : PC-BRASCII
d2 = 26, d3=0 : PC-ABICOMP
d2 = 17, d3=0 : ISO-8859-1
Specifies a line feed pitch of n/360 inch. (0 ≤ n ≤ 255)
ESC +
n
(27)D(43)D
n
(1B)H (2B)H
n
ESC -
n
(27)D(45)D
n
(1B)H (2D)H
n
Specifies or cancels underscoring.
n = 01, 31: Specifies underscoring.
n = 00, 30 : Cancels underscoring.
Selects the vertical tab channel. (0 ≤ n ≤ 7)
ESC /
m
(27)D(47)D
m
(1B)H (2F)H
m
ESC 0
ESC 2
ESC 3
n
(27)D(48)D
(27)D(50)D
(27)D(51)D
n
(1B)H (30)H
(1B)H (32)H
(1B)H (33)H
n
Specifies 1/8 inch line feed pitch.
Specifies 1/6 inch line feed pitch.
Specifies line feed pitch of n/180 inch. (0 ≤ n ≤ 255)
ESC 4
ESC 5
ESC 6
(27)D(52)D
(27)D(53)D
(27)D(54)D
(1B)H (34)H
(1B)H (35)H
Specifies the italic font.
Cancels the italic font.
(1B)H (36)H Expands the character code area.
Makes the area from (80)H to (9F)H the character code area,
rather than the control code area, when the graphic character
table or down-load character table is selected. This is the initial
condition.
ESC 7
ESC :
NUL
(27)D(55)D
(27)D(58)D
NUL
(1B)H (37)H Cancels the expanded character code area.
(1B)H (3A)H
NUL
Copies the internal character set. (0 ≤ n ≤ 255)
Draft mode: n = 0
n s
n s
n s
LQ mode: n = 0 ~ 9
s : Down-load character set number (See ESC &)
ESC <
(27)D(60)D
(1B)H (3C)H Returns to the home position.
Move the print head to the left end without sensing the home
position.
8. Software commands
—
—
8-3
Download from Www.Somanuals.com. All Manuals Search And Download.
● EPSON Software commands
Code
Symbol
Function
Decimal
Hex
ESC =
ESC >
ESC ?
n m
(27)D(61)D
(27)D(62)D
(27)D(63)D
n m
(1B)H (3D)H Specifies MSB 0
(1B)H (3E)H Specifies MSB 1
(1B)H (3F)H Converts the graphic modes.
n m (n= "K","L","Y","Z", m = 0 ≤ m ≤ 40)
Converts the
or
ESC K, ESC L, ESC Y ESC Z
graphic mode
into the
graphic mode.
ESC *
n: Graphic mode to be converted
m: New graphic mode
Horizontal dot density
m
Graphic mode
dpi
(dot/inch)
0
1
Single-density
Double-density
Double-speed double-density
Quadruple-density
CRT I
60 (8PIN)
120 (8PIN)
120 (8PIN)
240 (8PIN)
80 (8PIN)
90 (8PIN)
60 (24PIN)
120 (24PIN)
90 (24PIN)
180 (24PIN)
360 (24PIN)
2
3
4
6
CRT II
32
33
38
39
40
Single-density
Double-density
CRT III
Triple-density
Hex-density
The initial setting is as shown below;
ESC K = ESC
ESC L = ESC
ESC Y = ESC
ESC Z = ESC
●
●
●
●
00
01
02
03
ESC @
(27)D(64)D
(1B)H (40)H Initializes the printer.
Resets the print modes and clears command settings, data in the
print buffer and printing position.
Initialization item
Line feed pitch
Page length
TOF
Bottom margin
Vertical tab
Vertical tab channel
Right & left margins
Horizontal tab
Inter-character pitch
Character pitch
Special effect
Status
Specified in setup mode
Specified in setup mode
Regarding current line as TOF
Specified in setup mode
Setting when power is turned on
Channel 0
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Specified in setup mode
Specified in setup mode
0
Specified in setup mode
Canceled
own-load character
Not cleared
D
Character set
Specified in setup mode
Specified in setup mode
Canceled
Single-direction printing
MSB control
According to ESC ?
Graphic mode conversion
Canceled
Canceled
Justification
•
International character
Character font
Print buffer
Communication buffer
Printing position
Specified in setup mode
Specified in setup mode
Cleared
Not cleared
Left margin position
•
•
•
•
•
8. Software commands
—
—
8-4
Download from Www.Somanuals.com. All Manuals Search And Download.
● EPSON Software commands
Code
Symbol
Function
Decimal
Hex
ESC A
n
(27)D(65)D
n
(1B)H (41)H Specifies the line feed pitch in n/60 inch. (0 ≤ n ≤ 127)
n
ESC B
n1 n2
••• nk
NUL
(27)D(66)D
n1 n2
••• nk
(1B)H (42)H Specifies the vertical tab position. (1 ≤ nk ≤ 255, 1 ≤ k ≤ 16)
n1 n2
••• nk
NUL
This command can specify a maximum of 16 vertical tab
positions.
NUL
ESC C
n
(27)D(67)D
n
(1B)H (43)H Specifies the page length in number of lines. (1 ≤ n ≤ 127)
n
Valid when #32 PAGE LENGTH LOCK is set to NO in the
EXTENDED SETUP MODE.
ESC C
NUL n
(27)D(67)D
NUL n
(1B)H (43)H Specifies the page length in inches. (1 ≤ n ≤ 22)
NUL n
Valid when #32 PAGE LENGTH LOCK is set to NO in the
EXTENDED SETUP MODE.
ESC D
n1 n2
••• nk
(27)D(68)D
n1 n2
••• nk
(1B)H (44)H Specifies the horizontal tab position. (1 ≤ nk ≤ 255, 1 ≤ k ≤ 32)
n1 n2
••• nk
NUL
This command can specify a maximum of 32 horizontal tab
positions.
NUL
NUL
ESC E
ESC F
ESC G
ESC H
ESC J
ESC K
n1 n2
(27)D(69)D
(27)D(70)D
(27)D(71)D
(27)D(72)D
(27)D(74)D
(27)D(75)D
n1 n2
(1B)H (45)H Specifies emphasized printing.
(1B)H (46)H Cancels emphasized printing.
(1B)H (47)H Specifies the double striking.
(1B)H (48)H Cancels the double striking.
(1B)H (4A)H Executes line feeding at a pitch of n/180 inch. (0 ≤ n ≤ 255)
(1B)H (4B)H Specifies the 8-dot single-density graphic mode.
n1 n2
d1 d2
••• dk
Number of data k= n1 + n2 x 256
Horizontal dot density: 60 dpi
Maximum dots per line : 816 dot
d1 d2
••• dk
d1 d2
••• dk
ESC L
n1 n2
d1 d2
(27)D(76)D
n1 n2
d1 d2
(1B)H (4C)H Specifies the 8-dot double-density graphic mode.
n1 n2
d1 d2
••• dk
Number of data k = n1 + n2 x 256
Horizontal dot density: 120 dpi
Maximum dots per line : 1632 dot
••• dk
••• dk
ESC M
(27)D(77)D
(1B)H (4D)H Specifies 12 cpi (elite).
Valid when #34 PITCH LOCK is set to NO in the
EXTENDED SETUP MODE.
ESC N
n
ESC O
(27)D(78)D
n
(27)D(79)D
(1B)H (4E)H Specifies the bottom margin. (1 ≤ n ≤ 127)
n
This command is ignored in the CSF mode.
(1B)H (4F)H Cancels the bottom margin.
This command is ignored in the CSF mode.
(1B)H (50)H Specifies 10 cpi.
Valid when #34 PITCH LOCK is set to NO in the EXTENDED
ESC P
(27)D(80)D
SETUP MODE.
ESC Q
n
(27)D(81)D
n
(1B)H (51)H Specifies the right margin.
n
The right margin cannot exceed the paper width specified with
#4 or #5 in the SETUP MODE.
8. Software commands
—
—
8-5
Download from Www.Somanuals.com. All Manuals Search And Download.
● EPSON Software commands
Code
Symbol
Function
Decimal
Hex
ESC R
n
(27)D(82)D
n
(1B)H (52)H
n
Selects a national character type. (0 ≤ n ≤ 13, 31, 64)
n
0
1
2
3
23 24 40 5B 5C 5D
5E
60
7B 7C 7D 7E
NATION
U.S.A.
FRANCE
GERMANY
U.K.
4
5
6
DENMARK
SWEDEM
ITALY
7
SPAIN
8
JAPAN
9
10
11
NORWAY
DENMARK II
SPAIN II
12 LATIN AMERICA
13
31
64
KOREA
TURKEY
LEGAL
ESC S
n
(27)D(83)D
n
(1B)H (53)H
n
Specifies superscript or subscript.
n = 00, 30: Specifies superscript.
n = 01, 31: Specifies subscript.
Characters corresponding to the graphic character sets
to
(B0)H
and
are invalid.
(F5)H
(DF)H, (F4)H
ESC T
ESC U
n
(27)D(84)D
(27)D(85)D
n
(1B)H (54)H
(1B)H (55)H
n
Cancels superscript or subscript.
Specifies or cancels uni-directional printing.
n = 00, 30: Cancels uni-directional printing.
n = 01, 31: Specifies uni-directional printing.
Specifies or cancels double-width printing.
n = 00, 30: Cancels double-width printing.
n = 01, 31: Specifies double-width printing.
ESC W
n
(27)D(87)D
n
(1B)H (57)H
n
ESC Y
n1 n2
d1 d2
••• dk
(27)D(89)D
n1 n2
d1 d2
(1B)H (59)H
n1 n2
d1 d2
Specifies the 8-dot, double-speed, double-density graphic mode.
Number of data k = n1 + n2 x 256
Horizontal dot density: 120 dpi
••• dk
••• dk
Maximum dots per line: 1632 dot
Horizontally adjacent dots cannot be printed.
Specifies the 8-dot, quadruple-density graphic mode.
Number of data k= n1 + n2 x 256
Horizontal dot density: 240 dpi
Maximum dots per line : 3264 dot
ESC Z
n1 n2
d1 d2
••• dk
(27)D(90)D
n1 n2
d1 d2
(1B)H (5A)H
n1 n2
d1 d2
••• dk
••• dk
Horizontally adjacent dots cannot be printed.
8. Software commands
—
—
8-6
Download from Www.Somanuals.com. All Manuals Search And Download.
● EPSON Software commands
Code
Symbol
Function
Decimal
Hex
ESC \
n1 n2
(27)D(92)D
n1 n2
(1B)H (5C)H
n1 n2
Specifies the relative printing position.
Specifies where to start printing of the next data in relation to
the current position as shown below.
If
×
is less than
, the printing position
32768 [8000H]
(n1+n2 256)
moves to the right of the current position by
×
(n1+n2 256).
If
×
is equal to or more than
the
(n1+n2 256)
32768 [8000H],
printing position moves to the left of the current position by
–
×
65536 (n1+n2 256).
Printing mode
Draft
Unit of motion
1/ 120 inch
LQ or proportional
1/ 180 inch
ESC a
n
(27)D(97)D
n
(1B)H (61)H
n
Selects the printing position adjustment.
n = 00, 30 : Left justification
n = 01, 31 : Centering
n = 02, 32 : Right justification
n = 03, 33 : Justification
Left justification is selected by default.
Specifies the vertical tab position in each channel.
(0 ≤ m ≤ 7, 1 ≤ nk ≤ 255, 1 ≤ k ≤ 16)
ESC b
m
(27)D(98)D
m
(1B)H (62)H
m
n1 n2
••• nk
NUL
n1 n2
••• nk
NUL
n1 n2
••• nk
NUL
This command specifies the vertical tab position in channel m.
A maximum of 16 vertical tab positions can be specified.
m: Channel number
If m is equal to or more than 8, three bytes of ESC b m are
ignored.
ESC g
(27)D(103)D
(1B)H (67)H
Selects 15CPI.
Valid when #34 PITCH LOCK is set to NO.
Executes reverse feeding at a pitch of n/180 inch. (0 ≤ n ≤ 255)
ESC j
(27)D(106)D
(1B)H (6A)H
n
n
n
ESC k
n
(27)D(107)D
n
(1B)H (6B)H
n
Selects the font.
n
Font
(00)H
(01)H
(02)H
(03)H
(04)H
(05)H
(06)H
(07)H
(08)H
(14)H
ROMAN
SANS SERIF
COURIER
PRESTIGE ELITE
SCRIPT
OCR-B
OCR-A
ORATOR
ORATOR-S
GOTHIC
8. Software commands
—
—
8-7
Download from Www.Somanuals.com. All Manuals Search And Download.
● EPSON Software commands
Code
Symbol
Function
Decimal
Hex
ESC l
n
(27)D(108)D
n
(1B)H (6C)H
n
Specifies the left margin.
This command sets the left margin at the “n”th character by the
character width when the command is executed (including
double- width and inter-character SP).
Specifies or cancels proportional printing.
n = 00, 30 : Cancels proportional printing.
n = 01, 31 : Specifies proportional printing.
The draft and LQ modes have no difference for the proportional
printing. This command is valid when #34 PITCH LOCK is set
to NO.
ESC p
n
(27)D(112)D
n
(1B)H (70)H
n
ESC q
n
(27)D(113)D
n
(1B)H (71)H
n
Selects a special effect.
n = 00: Normal character
n = 01: Outline character
n = 02 : Shadow character
n = 03 : Outline with shadow character
Normal characters are selected by default.
Any characters corresponding to the graphic character sets
(B0)H to (DF)H and (F4)H to (F5)H.
ESC t
n
(27)D(116)D
n
(1B)H (74)H
n
Selects a character code table.
n = 00, 30 : Selects the italic character table.
n = 01, 31 : Selects the graphic character table.
n = 02, 32 : Selects the downloaded character table.
n = 03, 33 : Selects the graphic character table.
If downloaded characters cannot be printed when the
downloaded character table is selected, italic characters are
printed. The selected character table is changed with the
ETS ( t command.
ESC w
n
27)D(119)D
n
(1B)H (77)H
n
Specifies or cancels double-height printing.
n = 00, 30 : Cancels double-height printing.
n = 01, 31 : Specifies double-height printing.
Double-height printing does not apply to the graphic data.
Selects character.
ESC x
n
(27)D(120)D
n
(1B)H (78)H
n
n = 00, 30 : Selects draft characters.
n = 01, 31 : Selects LQ characters.
8. Software commands
—
—
8-8
Download from Www.Somanuals.com. All Manuals Search And Download.
● IBM Software commands
Code
Symbol
Function
Decimal
Hex
BEL
BS
HT
LF
(07)D
(08)D
(09)D
(10)D
(07)H
Activates the printer buzzer.
(08)H
(09)H
(0A)H
Moves the printing position to the left by one character.
Moves the printing position to the following horizontal tab.
Single-line feed
Causes carriage return if #28 LF SETTING is set to CR + LF in
the EXTENDED SETUP MODE.
VT
(11)D
(0B)H
Vertical tab
Moves the printing position to the left margin if #28 LF
SETTING is set to CR + LF in the EXTENDED SETUP MODE.
Form feed (Always moves the printing position to the left margin.)
Carriage return
FF
CR
(12)D
(13)D
(0C)H
(0D)H
Executes line feeding after carriage return if #27 CR SETTING
is set to CR + LF.
SO
SI
(14)D
(15)D
(0E)H
(0F)H
Double-width printing on a single line.
Specifies condensed mode.
Valid when #34 PITCH LOCK is set to NO in the EXTENDED
SETUP MODE.
DC1
(17)D
(11)H
Printer select
Changes the deselect condition established with ESC Q (23)H or
(B9)H to the select condition.
Valid when #71 SELECT IN ENABLE is set to 1 in the
EXTENDED SETUP MODE or SELECT IN ENABLE is set to
I/F and the SELECT IN signal is high.
Cancels the condensed mode.
DC2
(18)D
(12)H
Valid when #34 PITCH LOCK is set to NO in the EXTENDED
SETUP MODE.
DC4
CAN
(20)D
(24)D
(14)H
(18)H
Cancels the double-width mode established by the SO command.
Cancel
Clears all data in the print buffer and moves the printing
position to the beginning of the next line.
Designates ESC sequence.
Specifies the paper path.
n="R" : Ejects paper.
ESC
ESC EM
n
(27)D
(27)D(25)D
n
(1B)H
(1B)H (19)H
n
n="B" : Feeds paper with the rear tractor.
n="F" : Feeds paper with the front tractor.
n="M" : Feeds manually loaded paper.
n="f" : Ejects paper to the front.
n="t" : Ejects paper to the top.
n="r" : Ejects paper to the rear.
8. Software commands
—
—
8-9
Download from Www.Somanuals.com. All Manuals Search And Download.
● IBM Software commands
Code
Symbol
Function
Decimal
Hex
ESC
m
●
(27)D (42 )D
m
(1B)H (2A)H
m
Selects a graphic function.
Valid only when #26 AGM (Alternate Graphics Mode) is set to
n1 n2
d1 d2
n1 n2
d1 d2
n1 n2
d1 d2
YES in the EXTENDED SETUP MODE.
Horizontal dot density
dpi (dot/inch)
m (printing density) = 0, 1, 2, 3, 4, 6, 32, 33, 38,
39, 40
Mode
Pin
m
Max. dots per line
Single-density
8
8
0
1
60
120
Same as ESC K
Same as ESC L
... dk
... dk
... dk
Double-density
Double-speed
8
2
120
Same as ESC Y
double-density
●
Quadruple-density ●
CRT I
8
8
3
4
240
80
Same as ESC Z
CRT I
CRT II
8
6
90
CRT II
Single-density
Double-density
CRT III
Triple-density
Hex-density●
24
24
24
24
24
32
33
38
39
40
60
120
90
180
360
High density of ESC K
High density of ESC L
CRT III
Triple high density
Quadruple high density
●Horizontally adjacent dots can not be printed.
ESC –
n
(27)D (45 )D
n
(1B)H (2D)H
n
Specifies or cancels underscoring. (n = 0, 1)
ESC 0
ESC 1
ESC 2
(27)D (48 )D
(27)D (49 )D
(27)D (50 )D
(1B)H (30)H
(1B)H (31)H
(1B)H (32)H
Specifies line feed at a 1/8-inch pitch.
Specifies line feed at a 7/72-inch pitch.
Executes ESC A.
Sets the line feed pitch to the value specified by ESC A.
Specifies n/216 -inch line feed pitch. {1 ≤ n ≤ 255}
When n=0, this command is invalid.
ESC 3
n
(27)D (51 )D
n
(1B)H (33)H
n
ESC 3
n
(27)D (51 )D
n
(1B)H (33)H
n
Specifies n/180 -inch line feed pitch. (AGM) {1 ≤ n ≤ 255}
Setting of n = 0 is possible.
ESC 4
ESC 5
n
(27)D(52)D
(27)D(53)D
n
(1B)H (34)H
(1B)H (35)H
n
TOF Specifies.
Specifies or cancels automatic line feeding. {n = 0, 1}
Specifies whether to execute a carriage return and a line feed
or a carriage return only when executing the CR code.
n=0 : Carriage return only
n=1 : Carriage return and line feeding
ESC 6
ESC 7
ESC :
(27)D(54)D
(27)D(55)D
(27)D(58)D
(1B)H (36)H Specifies character set 2.
(1B)H (37)H Specifies character set 1.
(1B)H (3A)H
Specifies 12 CPI.
Valid when #34 PITCH LOCK is set to NO in the EXTENDED
SETUP MODE.
ESC =
n1 n2
(I.D.byte)
(adrs-low)
(adrs-high) (adrs-high)
data
(27)D(61)D
n1 n2
(I.D.byte)
(adrs-low)
(1B)H (3D)H Specifies downloading.
n1 n2
{0 ≤ n1 ≤ 255} {0 ≤ n2 ≤ 255} {I.D.byte = (23)H}
(I.D.byte)
(adrs-low)
(adrs-high)
data
{(00)H ≤ (adrs-low) ≤ (FF)H} {(00)H ≤ (adrs-high) ≤ (FF)H}
{(00)H ≤ data ≤ (FF)H}
The number of following data: n1+n2 256.
×
data
When n1=n2=0 , the downloading area is initialized. Two bytes,
(adrs-low)(adrs-high) show the memory address in which the first
byte of data is stored. The next data is stored in the following
address in sequence.
ESC A
n
(27)D(65)D
n
(1B)H (41)H Specifies the line feed pitch in units of n/72 inch. {1 ≤ n ≤ 255}
n
Specifies the line feed pitch in units of n/72 inch. When n = 0,
this command is invalid.
8. Software commands
—
—
8-10
Download from Www.Somanuals.com. All Manuals Search And Download.
● IBM Software commands
Code
Symbol
Function
Decimal
(27)D(65)D
n
Hex
ESC A
n
(1B)H (41)H Specifies the line feed pitch in units of n/60 inch {1 ≤ n ≤ 255} (AGM)
n
Specifies the line feed pitch in units of n/60 inch.
When n = 0 , this command is invalid.
ESC B
d1 d2
••• dk
NUL
ESC C
n
(27)D(66)D
d1 d2
••• dk
(00)D
(27)D(67)D
n
(1B)H (42)H Specifies the vertical tabs.
d1 d2
••• dk
A maximum of 64 tabs can be specified.
Specify vertical tabs from the lowest tab and end with (00)H.
(00)H
(1B)H (43)H
n
Specifies the page length in number of lines.{1 ≤ n ≤ 255}
The maximum page length is 182 inches.
Valid when #32 PAGE LOCK is set to NO in the
EXTENDED SETUP MODE.
ESC C
NUL n
(27)D(67)D
(1B)H (43)H Specifies the page length in inches. {1 ≤ n ≤ 182}
(00)D
n
(00)H
n
Valid when #32 PAGE LOCK is set to NO in the
EXTENDED SETUP MODE.
ESC D
d1 d2
••• dk
(27)D (68 )D
d1 d2
••• dk
(1B)H (44)H Specifies the horizontal tabs.
d1 d2
••• dk
(00)H
A maximum of 28 tabs can be specified.
Specify horizontal tabs from the lowest tab and end with (00)H.
NUL
(00)D
ESC E
ESC F
ESC G
ESC H
ESC I
n
(27)D(69)D
(27)D(70)D
(27)D(71)D
(27)D(72)D
(27)D(73)D
n
(1B)H (45)H Specifies emphasized printing.
(1B)H (46)H Cancels emphasized printing.
(1B)H (47)H Specifies double-striking.
(1B)H (48)H Cancels double-striking.
(1B)H (49)H Selects a font.
n = 0, 2, 3, 4, 6, 7, 8, 10, 12, 14, 16, 18, 20, 22
n
n
Internal/download Character quality Character width
0
Internal font
Internal font
Internal font
Download
Download
Download
Internal font
Internal font
Download
Download
Internal font
Internal font
Download
Download
Draft
LQ
10 CPI
2
3
10 CPI
LQ
Proportional
10 CPI
4
Draft
LQ
6
10 CPI
7
LQ
Proportional
12 CPI
8
Draft
LQ
10
12
14
16
18
20
22
12CPI
Draft
LQ
12 CPI
12 CPI
Draft
LQ
Condensed
Condensed
Condensed
Condensed
Draft
LQ
If the value “n” is not as specified above, this command is invalid.
ESC J
n
(27)D(74)D
n
(1B)H (4A)H Executes line feeding at a pitch of n/216 inches. (1 ≤ n ≤ 255)
n
ESC J
n
(27)D(74)D
n
(1B)H (4A)H Executes line feeding at a pitch of n/180 inches. (AGM) (1 ≤ n ≤ 255)
n
ESC K
n1 n2
d1 d2
••• dk
ESC L
n1 n2
d1 d2
••• dk
(27)D(75)D
n1 n2
d1 d2
••• dk
(27)D(76)D
n1 n2
(1B)H (4B)H Specifies the 8-dot single- density graphic mode.
n1 n2
d1 d2
••• dk
Number of data k = n1 + n2 x 256
Horizontal dot density : 60dpi
Maximum dots per line: 816 dot
(1B)H (4C)H Specifies the 8-dot double-density graphic mode.
n1 n2
d1 d2
••• dk
Number of data k = n1 + n2 x 256
Horizontal dot density : 120dpi
Maximum dots per line : 1632 dot
d1 d2
••• dk
8. Software commands
—
—
8-11
Download from Www.Somanuals.com. All Manuals Search And Download.
● IBM Software commands
Code
Symbol
Function
Decimal
(27)D(78)D
n
Hex
(1B)H (4E)H
n
ESC N
n
Specifies the bottom margin. (1 ≤ n ≤ 255)
The number of lines to be skipped is specified by “n” and the
bottom margin is specified in the preset line feed amount.
Cancels the bottom margin.
Specifies or cancels proportional printing.
n = 0 : Cancels proportional printing.
ESC O
ESC P
n
(27)D(79)D
(27)D(80)D
n
(1B)H (4F)H
(1B)H (50)H
n
n = 1 : Specifies proportional printing.
This command is valid when #34 PITCH LOCK is set to NO.
Printer deselect
Brings the printer into the deselect state when n=(23)H,(B9)H.
Valid when #71 SELECT IN ENABLE is set to 1 in the
EXTENDED SETUP MODE or set to I/F and the SELECT IN
signal is high.
ESC Q
n
(27)D(81)D
n
(1B)H (51)H
n
ESC R
(27)D(82)D
(1B)H (52)H
Initializes the horizontal and vertical tab positions.
Clears the vertical tab position.
ESC S
n
(27)D(83)D
n
(1B)H (53)H
n
Specifies superscript or subscript.
n = 0 : Specifies superscript.
n = 1 : Specifies subscript.
ESC T
ESC U
n
(27)D(84)D
(27)D(85)D
n
(1B)H (54)H
(1B)H (55)H
n
Cancels superscript or subscript.
Specifies or cancels uni-directional printing.
n = 0 : Cancels uni-directional printing.
n = 1 : Specifies uni-directional printing.
Specifies or cancels double-width printing.
n = 0 : Cancels double-width printing.
ESC W
n
(27)D(87)D
n
(1B)H (57)H
n
n = 1 : Specifies double-width printing.
Specifies the right and left margins. {0 ≤ n ≤ 255} {0 ≤ m ≤ 255}
ESC X
n m
(27)D(88)D
n m
(1B)H (58)H
n m
ESC Y
n1 n2
d1 d2
••• dk
(27)D(89)D
n1 n2
d1 d2
(1B)H (59)H
n1 n2
d1 d2
Specifies the 8-dot double-speed double-density graphic mode.
Number of data k = n1 + n2 × 256
Horizontal dot density : 120 dpi
Maximum dots per line : 1632 dot
••• dk
••• dk
Horizontally adjacent dots cannot be printed.
Specifies the quadruple-density graphic mode.
Number of data k = n1 + n2 × 256
Horizontal dot density : 240 dpi
Maximum dots per line : 3264 dot
Horizontally adjacent dots cannot be printed.
Specifies the line type.
ESC Z
n1 n2
d1 d2
••• dk
(27)D(90)D
n1 n2
d1 d2
(1B)H (5A)H
n1 n2
d1 d2
••• dk
••• dk
ESC [ -
n1 n2
(27,91,45)D
n1 n2
(1B, 5B, 2D)H
n1 n2
Number of data k = n1 + n2 × 256
m1 m2
m1 m2
m1 m2
m1 = 1 : Underscore m2 = 0 : Cancels the line specification.
m1 = 2 : Center line m2 = 1 : Single line
m1 = 3 : Upper line m2 = 2 : Double lines
m2 = 255 : Cancels the line specification.
8. Software commands
—
—
8-12
Download from Www.Somanuals.com. All Manuals Search And Download.
● IBM Software commands
Code
Symbol
Function
Decimal
Hex
ESC [ @ (27,91,64)D
(1B, 5B, 40)H
n1 n2
Specifies or cancels double-width, double-height printing.
n1 n2
n1 n2
n1+n2 256 indicates the number of following data.
×
Normally, n1=4 and n2=0.
m1 m2
m3 m4
m1 m2
m3 m4
m1 m2
m3 m4
{n1 = 4} {n2 = 0} {m1 = 00, 01, 02, 04, 08, 10, 20 H}
{m3 = 00, 01, 02, 10, 11, 12, 20, 21, 22 H}
{m4 = (00)H, (01)H, (02)H)} {m2 = 0}
This command specifies or cancels double-height, double-width
printing.
m1 = 1 : Specifies italic characters.
m1 = 2 : Cancels italic characters.
m1 = 4 : Specifies the outline characters.
m1 = 8 : Cancels the outline characters.
m1 = 16 : Specifies shadow characters.
m1 = 32 : Cancels shadow characters.
m2 : Meaningless
m3 : High order half-byte (4 bit) indicates Line Feed.
Low order half-byte (4 bit) indicates High.
m4 : Low order half-byte (4 bit) indicates Width.
Line Feed indicates the mode where the line feed pitch is
doubled. High indicates the mode where the height is doubled.
Width indicates the mode where the width is doubled.
Setting is;
0
: Not changed
1
2
3
: Standard size
: Double size
or more: Same as 0.
Graphic symbols are printed in the standard size.
(1B, 5B, 4B)H Software initial
ESC [ K (27,91,75)D
n1 n2
n1 n2
n1 n2
n1+n2 256 indicates the number of the next data.
×
m1 m2
m3 m4
m1 m2
m3 m4
m1 m2
m3 m4
When m1 =00, 04, FE H, initialization is executed without clearing
downloading.
m1 =01, 05, FF H, initialization is executed with clearing
download area.
m2 = 03, 16, 23, 24, B1, B4 H, the next two bytes of data are valid.
m 3
m 4
bit 7
bit 6
0 : m 3 is valid.
1 : m 3 is invalid.
—————
0 : m 4 is valid.
1 : m 4 is invalid.
Code page
0 : 437
1 : 850
—————
—————
bit 5
bit 4
—————
LF code
0 : LF only
1 : LF + CR
CR code
0 : C R only
1 : CR + LF
Page length
0 : 11 inches
1 : 12 inches
Zero font
bit 3
bit 2
bit 1
bit 0
—————
—————
Printing range
0 : 13.6 inches
1 : 8 inches
0 : No slash
1 : With slash
Character set
0 : Set 1
—————
1 : Set 2
8. Software commands
—
—
8-13
Download from Www.Somanuals.com. All Manuals Search And Download.
● IBM Software commands
Code
Symbol
Function
Decimal
Hex
ESC [ I
n1 n2
Hf Lf
(27,91,73)D
n1 n2
Hf Lf
(1B, 5B,49)H
n1 n2
Hf Lf
Selects the font.
n1 + n2 x 256 indicates the number of the next data.
Hf, Lf = FONT ID
Hs Ls
Sm 00
Hc Lc
Hs Ls
Sm 00
Hc Lc
Hs Ls
Sm 00
Hc Lc
Hs, Ls = Size (pitch & height)
Sm = 1: Font size is specified with Hs, Ls.
Sm = 2 or 3 : Specifies proportional printing.
Hs, Ls, Sm is valid only when the font ID specified with Hf, Lf
is invalid or ignored.
Hc, Lc specifies the code page.
The following table shows the relationship between the Hf, Lf
values and fonts.
Hf
Lf
Hf Lf
(01)H (D4)H SCRIPT
(01)H (D5)H SCRIPT
(01)H (D6)H SCRIPT
(01)H (D7)H SCRIPT
(01)H (D8)H SCRIPT
(01)H (24)H SCRIPT
(00)H (C8)H SCRIPT
10CPI
12CPI
15CPI
17CPI
20CPI
24CPI
PROP
(00)H (0B)H COURIER
(01)H (EB)H COURIER
(01)H (EC)H COURIER
(01)H (ED)H COURIER
(01)H (EE)H COURIER
(01)H (1E)H COURIER
(00)H (AB)H COURIER
10CPI
12CPI
15CPI
17CPI
20CPI
24CPI
PROP
(00)H (0C)H PRESTIGE 10CPI
(01)H (EF)H PRESTIGE 12CPI
(01)H (F0)H PRESTIGE 15CPI
(01)H (C9)H PRESTIGE 17CPI
(01)H (CA)H PRESTIGE 20CPI
(01)H (1F)H PRESTIGE 24CPI
(00)H (A4)H PRESTIGE PROP
Hf
Lf
(00)H (12)H COURIER 10CPI Italic
(00)H(2E)H COURIER 10CPI Emphasized
(00)H (39)H COURIER 10CPI Emphasized italic
(00)H (55)H COURIER 12CPI
(00)H(5C)H COURIER 12CPI Italic
(00)H(6C)H COURIER 12CPI Emphasized
(00)H (74)H COURIER 12CPI Emphasized italic
(00)H(AC)H COURIER PROP Italic
(00)H(B8)H COURIER PROP Emphasized
(00)H(B9)H COURIER PROP Emphasized italic
(00)H(D6)H COURIER 15CPI Emphasized
(00)H(D7)H COURIER 15CPI Italic
(00)H (24)H GOTHIC
(01)H (8F)H GOTHIC
(01)H (8E)H GOTHIC
(01)H (8D)H GOTHIC
(01)H (8C)H GOTHIC
(01)H (20)H GOTHIC
(00)H (AE)H GOTHIC
10CPI
12CPI
15CPI
17CPI
20CPI
24CPI
PROP
(00)H(D8)H COURIER 15CPI Emphasized italic
(00)H(DF)H COURIER 15CPI
(00)H (F6)H COURIER 10CPI Double-width, double-height
(00)H (F4)H COURIER 10CPI Double-width, double-height
(00)H (F5)H COURIER 10CPI
(00)H(FD)H COURIER 17.1CPI Emphasized
(00)H(FE)H COURIER 17.1CPI
(00)H (19)H ORATORs
(01)H (D0)H ORATORs
(01)H (D1)H ORATORs
(01)H (D2)H ORATORs
(01)H (D3)H ORATORs
(01)H (23)H ORATORs
(00)H (C7)H ORATORs
10CPI
12CPI
15CPI
17CPI
20CPI
24CPI
PROP
Emphasized double-width, double-height
(00)H(3C)H PRESTIGE 10CPI Emphasized
(00)H (56)H PRESTIGE 12CPI
(00)H (6F)H PRESTIGE 12CPI Emphasized
(00)H (70)H PRESTIGE 12CPI Italic
(00)H(DD)H PRESTIGE 15CPI
(00)H (05)H ORATOR
(01)H (CB)H ORATOR
(01)H(CC)H ORATOR
(01)H(CD)H ORATOR
(01)H (CE)H ORATOR
(01)H (21)H ORATOR
(00)H (C6)H ORATOR
10CPI
12CPI
15CPI
17CPI
20CPI
24CPI
PROP
(01)H (00)H PRESTIGE 17.1CPI
8. Software commands
—
—
8-14
Download from Www.Somanuals.com. All Manuals Search And Download.
● IBM Software commands
Function
Hf
Lf
The following shows the relationship between the
(00)H (57)H GOTHIC 12CPI
(00)H (6D)H GOTHIC 12CPI Italic
(00)H (6E)H GOTHIC 12CPI Emphasized
(00)H (9D)H GOTHIC PROP Emphasized
(00)H (A2)H GOTHIC PROP Italic
(00)H (DE)H GOTHIC 15CPI
(00)H (F1)H GOTHIC 10CPI Double-width,
double-height
(00)H (F2)H GOTHIC 10CPI Emphasized
Double-width,
double-height
(00)H (F3)H GOTHIC 10CPI Emphasized
Double-striking
Hs, Ls values and sizes.
Hs,Ls
00,00-00,41
00,42-00,4D
00,4E-00,59
00,5A-00,6B
00,6C-00,83
00,84-00,9B
00,9C-00,B3
00,B4-00,D7
00,D8-00,FE
24CPI
20CPI
17CPI
15CPI
12CPI
10CPI
17CPI
15CPI
12CPI
Subscript
Subscript
Normal
Normal
Normal
Normal
Double-width
Double-width
Double-width
Double-hight
Double-width
Double-hight
Double-width,
double-height
00,FF-FF,FF
10CPI
(00)H (FF)H GOTHIC 17.1CPI
(01)H (19)H GOTHIC 20CPI
The following shows the relationship between the
Hc, Lc values and the code page.
(32)H (00)H ROMAN 10CPI
(32)H (01)H ROMAN 12CPI
(32)H (02)H ROMAN 15CPI
(32)H (03)H ROMAN 17CPI
(32)H (04)H ROMAN 20CPI
(32)H (05)H ROMAN 24CPI
(32)H (06)H ROMAN PROP
Hc
Lc Dec(Hc,Lc) CODE PAGE
(01)H (B5)H
(03)H (52)H
(03)H (5C)H
(03)H (5F)H
(03)H (61)H
(03)H (59)H
(03)H (5A)H
437
850
860
863
865
857
858
CODE PAGE 437
CODE PAGE 850
CODE PAGE 860
CODE PAGE 863
CODE PAGE 865
CODE PAGE 857
CODE PAGE 858
ISO-8859-1
(32)H (10)H SANS SERIF 10CPI
(32)H (11)H SANS SERIF 12CPI
(32)H (12)H SANS SERIF 15CPI
(32)H (13)H SANS SERIF 17CPI
(32)H (14)H SANS SERIF 20CPI
(32)H (15)H SANS SERIF 24CPI
(32)H (16)H SANS SERIF PROP
(40)H (00)H 16384
(03)H (5d)H
(0F)H (07)H
(0F)H (08)H
861
3847
3848
CODE PAGE 861
CODE PAGE BRASCII
CODE PAGE ABICOMP
(32)H (20)H OCR-A
(32)H (21)H OCR-A
(32)H (23)H OCR-A
(32)H (24)H OCR-A
10CPI
12CPI
17CPI
20CPI
(32)H (30)H OCR-B
(32)H (31)H OCR-B
(32)H (33)H OCR-B
(32)H (34)H OCR-B
10CPI
12CPI
17CPI
20CPI
8. Software commands
—
—
8-15
Download from Www.Somanuals.com. All Manuals Search And Download.
● IBM Software commands
Code
Symbol
Function
Decimal
Hex
ESC [ T
n1 n2
(27,91,84)D
n1 n2
(1B, 5B, 54)H
n1 n2
Selects the code page. (n1=4 n2=0 n3=0 n4=0)
n1 + n2 x 256 indicates the number of the next data.
n3 n4
n5 n6
n3 n4
n5 n6
n3 n4
n5 n6
n5=(01)H
(03)H
(03)H
(03)H
(03)H
(03)H
(03)H
(40)H
(03)H
(0F)H
(0F)H
n6=(B5)H
(52)H
(59)H
(5A)H
(5C)H
(5F)H
(61)H
(00)H
(5D)H
(07)H
(08)H
437
850
857
858
860
863
865
ISO-8859-1
861
BRASCII
ABICOMP
ESC [ \
n1 n2
m1 m2
m3 m4
(27,91,92)D
n1 n2
m1 m2
(1B, 5B, 5C)H
n1 n2
m1 m2
Specifies the basic amount of line feeding.
(n1=4 n2=0 m1=0 m2=0 m3=0,104,180,216 m4=0,1,180,216)
n1 + n2 x 256 indicates the number of the next data.
When m3=0 and m4=216 or m3=216 and m4=0 , the basic line
feed pitch is 1/216 inch.
m3 m4
m3 m4
When m3=0 and m4=180 or m3=180 and m4=0 , the basic line
feed pitch is 1/180 inch.
When m3=104 and m4=1, the basic line feed pitch is 1/360 inch.
The basic line feed pitch is 1/216 inch (when not in the AGM
mode) or 1/180 inch (in the AGM mode) by default.
Selects character quality. (n1=1 n2=0)
n1 + n2 x 256 indicates the number of the next data.
n3 = 0 : Not changed.
ESC [ d
n1 n2
n3
(27,91,100)D
n1 n2
n3
(1B, 5B, 64)H
n1 n2
n3
n3 =(01)H - (7F)H Draft
n3 =(80)H - (BF)H LQ
n3 =(C0)H -(FE)H Emphasized LQ
n3 =(FF)H LQ
Valid when #35 QUALITY LOCK is set to NO in the
EXTENDED SETUP MODE.
ESC [ g
n1 n2
m
d1 d2
••• dk
(27,91,103)D
n1 n2
m
d1 d2
••• dk
(1B, 5B, 67)H
n1 n2
m
d1 d2
••• dk
Graphic mode
n1+n2
{0 ≤ n1 ≤ 255}{0 ≤ n2 ≤ 255} {m = 0, 1, 2, 3, 8, 9, 11, 12, 16}
m indicates the graphic mode (density) as shown below.
×
256 specifies (graphic data + 1).
m =
0
1
2
3
8
8 pin
60 dpi
120
120 (*)
240 (*)
60
8
8
8
24
9
24
24
24
48
120
180
360 (*)
360 (*)
11
12
16
In a graphic mode marked with an asterisk (*)
horizontally adjacent dots cannot be printed.
8. Software commands
—
—
8-16
Download from Www.Somanuals.com. All Manuals Search And Download.
● IBM Software commands
Code
Symbol
Function
Decimal
Hex
ESC \
n1 n2
d1 d2
•••dk
(27)D (92)D
n1 n2
d1 d2
(1B)H (5C)H
n1 n2
d1 d2
All-character set {0 ≤ n1 ≤ 255}{0 ≤ n2 ≤ 255}
Prints n1 + n2 × 256 characters in the all-character character set.
•••dk
•••dk
ESC ]
(27)D (93)D
(1B)H (5D)H
Reverse line feeding.
This command does not execute a carriage return even when an
automatic carriage return is specified.
ESC ^
n
(27)D (94)D
n
(1B)H (5E)H
n
All-character set for a single character. {0 ≤ n ≤ 255}
Prints only one character following ESC ^ in the all-character
character set.
ESC _
n
(27)D (95)D
n
(1B)H (5F)H
n
Specifies or cancels the upper line.
n = 1 : Specifies the upper line.
n = 0 : Cancels the upper line.
ESC d
n1 n2
(27)D (100)D
n1 n2
(1B)H (64)H
n1 n2
Specifies the relative printing position. {0 ≤ n1 ≤ 255}{0 ≤ n2 ≤ 255}
Advances the printing position by (n1+n2
×
256)/120 inch.
ESC j
(27)D (106)D
(1B)H (6A)H
Stops printing.
After printing, this command activates the buzzer and disables
printing.
8. Software commands
—
—
8-17
Download from Www.Somanuals.com. All Manuals Search And Download.
● HP Software commands
Code
Symbol
Function
Decimal
(07)D
Hex
(07)H
BEL
BS
HT
LF
Activates the printer buzzer. (Available in PCL3+ or PCL3+D)
Backspace one character.
Moves to next horizontal tab.
Linefeeds after printing.
Form feeds after printing.
Carriage return after printing.
Selects secondary font.
(08)D
(09)D
(10)D
(12)D
(13)D
(14)D
(15)D
(27)D
(32)D
(127)D
(08)H
(09)H
(0A)H
(0C)H
(0D)H
(0E)H
(0F)H
(1B)H
(20)H
(7F)H
FF
CR
SO
SI
ESC
SP
DEL
Selects prinmary font.
Designate start of escape sequence.
Space one character.
To print the ASCII DEL character.
ESC & a (27,38,97,#, (1B,26,61,#, Horizontal positioning by column.
# C 67)D 43)H
ESC & a (27,38,97,#, (1B,26,61,#, Horizontal positioning by 1/720”.
# H 72)D 48)H
ESC & a (27,38,97,#, (1B,26,61,#, Sets left margin.
# L 76)D 4C)H
ESC & a (27,38,97,#, (1B,26,61,#, Sets right margin.
# M 77)D 4D)H
ESC & a (27,38,97,#, (1B,26,61,#, Vertical positioning by line (VMI).
# R 82)D 52)H
ESC & a (27,38,97,#, (1B,26,61,#, Vertical positioning by 1/720”.
# V 86)D 56)H
ESC & d (27,38,100,#, (1B,26,64,#, Designates underline mode.
# D 68)D 44)H
ESC & d (27,38,100,#, (1B,26,64,#, Cancels underline mode.
# @ 64)D 40)H
ESC & k (27,38,107,#, (1B,26,6B,#, Designates/Cancels the auto-cancellation of underline.
# E 69)D 45)H
ESC & k (27,38,107,#, (1B,26,6B,#, Designates/Cancels the auto-cancellation of secondary font.
# F
70)D
46)H
If # is seto to “0”, current secondary font set changes
automatically to primary font when vertical position changes.
ESC & k (27,38,107,#, (1B,26,6B,#, Designates line termination.
# G
71)D
47)H
# = 0 (30H) :CR=CR, LF=LF, FF=FF
# = 1 (31H) :CR=CR+LF, LF=LF, FF=FF
# = 2 (32H) :CR=CR, LF=LF+CR, FF=FF+CR
# = 3 (33H) :CR=CR+LF, LF=LF+CR, FF+CR
ESC & k (27,38,107,#, (1B,26,6B,#, Sets HMI (Horizontal motion index).
# H
72)D
48)H
HMI is set by 1/120 inch.
HMI is defined as the distance where the print position moves
when the character code is input.
If # is 12, the input characters are printed in 10 cpi.
ESC & k (27,38,107,#, (1B,26,6B,#, Designates character pitch.
# S
83)D
53)H
Character pitch is set.
# = 0 (30H) :Normal (10 cpi)
# = 1 (31H) :Double width (5 cpi)
# = 2 (32H) :Compressed (16.7 cpi)
# = 4 (34H) :12 cpi
8. Software commands
—
—
8-18
Download from Www.Somanuals.com. All Manuals Search And Download.
● HP Software commands
Code
Symbol
Function
Decimal
Hex
ESC & k (27,38,107,#, (1B,26,6B,#, Designates/Cancels automatic scroll mode.
# V
86)D
56)H
# =0 (30H) :Designates automatic scroll mode.
# =1 (31H) :Cancels automatic scroll mode.
ESC & k (27,38,107,#, (1B,26,6B,#, Controls print direction. (Available in PCL3+ or PCL3+D)
# W
87)D
57)H
Print direction is set as follows.
# = 0 (30H) :Unidirectional Print(left to right)
# = 1 (31H) :Bidirectional Print
# = 2 (32H) :Pre-directional Print
ESC & l (27,38,108,#, (1B,26,6C,#, Designates paper size.
# A
65)D
41)H
Paper size is set as follows.
# = 0 (30H) :(Setting in the setup mode)
# = 2 (32H) :Letter
# = 3 (33H) :Legal
# = 26 (32H,36H) :A4
# = 81 (38H,31H) :ENVELOP Commercial-10
ESC & l (27,38,108,#, (1B,26,6C,#, Sets VMI (Vertical motion index).
# C
67)D
43)H
VMI is set by 1/48 inch.
VMI is defined as the distance where the print position moves
when the LF code is input. If # is 8, the print position moves
in 6 LPI vertically.
ESC & l (27,38,108,#, (1B,26,6C,#, Sets the line spacing. VMI (Vertical motion index)
# D
68)D
44)H
# = The number of LPI (lines per inch).
# = 8 (38H) :8 LPI
ESC & l (27,38,108,#, (1B,26,6C,#, Sets top margin by VMI. (where # = “1,2, ...)
# E
69)D
45)H
When the top margin is set, the text length is set to the default.
In case of skip perforation ON
Text length = page length- top margin-1/2"
(Bottom margin is set to 1/2")
In case of skip perforation OFF
Text length = page length- top margin
(Bottom margin is set to 0")
ESC & l (27,38,108,#, (1B,26,6C,#, Sets text length.
# F 70)D 46)H Text length is set by line (VMI).
ESC & l (27,38,108,#, (1B,26,6C,#, Sets paper path.
# H
72)D
48)H
The mode set as follows.
# = 0 (30H) :Ejects Paper.
# = 1 (31H) :Feeds paper with the CSF.
# = 2 (32H) :Feeds manually loaded paper.
# = -1 (2DH,31H) :Feeds paper with the front tractor.
# = -2 (2DH,32H) : Feeds paper with the rear tractor.
# = -10 (2DH,31H,30H) :Ejects paper to the front.
# = -11 (2DH,31H,31H) :Ejects paper to the top
# = -11 (2DH,31H,32H) :Ejects paper to the rear.
When the "NOT INSTALL" is selected in the" SETUP #60
OPTION," the CSF command is the same as #=0.
8. Software commands
—
—
8-19
Download from Www.Somanuals.com. All Manuals Search And Download.
● HP Software commands
Code
Symbol
Function
Decimal
Hex
ESC & l (27,38,108,#, (1B,26,6C,#, Designates/Cancels skip perforation mode.
# L
76)D
4C)H
Paper path is set as follows.
# = 0 (30H) :Cancels the skip perforation mode
# = 1 (31H) :Designates the skip perforation mode
ESC & l (27,38,108,#, (1B,26,6C,#, Sets page length by VMI.
# P 80)D 50)H
ESC & p (27,38,112,#, (1B,26,70,#, Receives data as text.
# X 88)D 58)H
ESC & s (27,38,115,#, (1B,26,73,#, Designates/Cancels wraparound.
# C
67)D
43)H
# = 0 (30H) :Designates wraparound
# = 1 (31H) :Cancels wraparound
ESC (
id
ESC )
id
(27,40,id)D
(27,41,id)D
(1B,28,id)H
(1B,29,id)H
Assign font to the primary/secondary font set.
id
Font
id
Font
0 A MATH-SYMBOL
0 B LINE-DRAW
●
10U PC-8
11U PC-8, DENMARK/NORWAY
12U PC-850
0 D ISO-60, NORWAY 1
0 E ROMAN-EXTENSION
0 F ISO-25, FRANCE 2
0 G GERMANY 2
2 S ISO17,SPAIN 1
2 U ISO2, IRV
●
●
3 S ISO10, SWEDEN 2
4 S ISO16, PORTUGAL 1
0 I ISO15, ITALY
0 K ISO14, JIS, ASCI
0 L LINE-DRAW
5 S ISO84, PORTUGAL 2
6 S ISO85, SPAIN 2
8 U ROMAN-8
●
●
0 M MATH 7
●
0 N ECMA 94, LATIN 1 (ISO-8859-1) 80U CODE PAGE 857
●
●
●
●
●
●
●
0 U ASCII
81U CODE PAGE 860
82U CODE PAGE 863
83U CODE PAGE 865
93U CODE PAGE 858
94U CODE PAGE 861
95U CODE PAGE BRASCII
0 S ISO11, SWEDEN 1
1 D ISO61, NORWAY 2
1 E ISO4, UK
1 F ISO-69, FRANCE 1
1 G ISO-21, GERMANY 1
1 S SPAIN 3
●
●
96U CODE PAGE ABICOMP ●
1 U LEGAL
● : Avaliable in PCL3+ or PCL3+D mode
ESC ( # (27,40,#,
64)D
(1B,28,#,
40)H
Designates primary font.
# = 0 or 1 (30H or 31H) :
@
Copy the default primary symbol set to the current primary
symbol set.
# = 2 (32H) :
Copy the current primary symbol set to the current primary
symbol set.
# = 3 (33H) :
Copy the default primary font to the current primary font.
Assigns the download font to the current primary/secondary
font.
ESC ( 0 (27,40,48,
88)D
ESC ) 0 (27,41,48,
(1B,28,30,
58)H
(1B,29,30,
58)H
X
X
88)D
8. Software commands
—
—
8-20
Download from Www.Somanuals.com. All Manuals Search And Download.
● HP Software commands
Code
Symbol
Function
Decimal
Hex
ESC ( s (27,40,115,#, (1B,28,73,#, Bold or emphasized.
# B 66)D 42)H Designates/Cancels bold or emphasized attributes as follows.
ESC ) s (27,41,115,#, (1B,29,73,#, # = 0 (30H) :Bold off/Emphasized off
# B
66)D
42)H
# = 3 (33H) :Bold on /Emphasized off
# = 7 (37H) :Bold off/Emphasized on
ESC ( s (27,40,115,#, (1B,28,73,#, Sets character spacing. (# = Font pitch (CPI))
# H 72)D 48)H PCL mode = PCL3+, PCL3+D or PCL3
ESC ) s (27,41,115,#, (1B,29,73,#, # = 5
:5 cpi
:10 cpi
:12 cpi
(0.01≤#<5.01)
(5.01≤#<10.01)
(10.01≤#<12.01)
# H
72)D
48)H
# = 10
# = 12
PCL mode = PCL3+ or PCL3+D
# = 15 :15 cpi (12.01≤#<15.01)
# = 16.7 :16.7 cpi (15.01≤#<16.71)
# = 17.1 :17.1 cpi (16.71≤#<17.11)
# = 20
:20 cpi
(17.11≤#<20.01)
# = 24
:24 cpi
(20.01≤#)
PCL mode = PCL3
# = 16.7 :16.7 cpi (12.01≤#<16.71)
# = 20 :20 cpi (16.71 ≤#)
ESC ( s (27,40,115,#, (1B,28,73,#, Selects proportional or fixed character spacing.
# P 80)D 50)H # = 1 (31H) :Proportional pitch
ESC ) s (27,41,115,#, (1B,29,73,#, # = 0 (30H) :Fixed pitch
# P 80)D 50)H
ESC ( s (27,40,115,#, (1B,28,73,#, Sets print quality.
# Q 81)D 51)H # = 0 (30H) :Draft
ESC ) s (27,41,115,#, (1B,29,73,#, # = 2 (32H) :Letter Quality
# Q 81)D 51)H
ESC ( s (27,40,115,#, (1B,28,73,#, Sets italic character.
# S 83)D 53)H # = 0 (30H) :Cancels italic character
ESC ) s (27,41,115,#, (1B,29,73,#, # = 1 (31H) :Designates italic character
# S 83)D 53)H # = 2 (32H) :Designates italic character
ESC ( s (27,40,115,#, (1B,28,73,#, Sets typeface.
# T 84)D 54)H # = 0 (30H)
ESC ) s (27,41,115,#, (1B,29,73,#, # = 3 (33H)
LINE PRINTER DRAFT
COURIER
# T
84)D
54)H
# = 4 (34H)
# = 5 (35H)
# = 6 (36H)
# = 7 (37H)
# = 8 (38H)
SANSERIF
ROMAN
GOTHIC
SCRIPT*
PRESTIGE
# = 10 (31H,30H) ORATOR*
# = 11 (31H,31H) ORATOR-S*
# = 20 (32H,30H) OCR-A*
# = 21 (32H,31H) OCR-B*
*= Available in PCL3+ or PCL3+D
8. Software commands
—
—
8-21
Download from Www.Somanuals.com. All Manuals Search And Download.
● HP Software commands
Code
Symbol
Function
Decimal
Hex
ESC ( s (27,40,115,#, (1B,28,73,#, Sets super/subscript.
# U 85)D 55)H # = + 1 (2BH,31H) :Designates superscript
ESC ) s (27,41,115,#, (1B,29,73,#, # = 0 (30H) :Cancels super/subscript
# U 85)D 55)H # = - 1 (2DH,31H) :Designates subscript
ESC ( s (27,40,115,#, (1B,28,73,#, Sets character point size.
# V 86)D 56)H # = 12 (31H,32H) :Standard font
ESC ) s (27,41,115,#, (1B,29,73,#, # = 8 (38H) :Micro font
# V 86)D 56)H
ESC ( s (27,40,115,#, (1B,28,73,#, Download character descriptor and data.
# W
DATA
87)D
DATA
57)H
DATA
The parameter # consists of 3 bytes of the descriptor.
<Attribute data format>
1 st
2 nd
3 rd
8
0
1
(Attribute format)
(Continuation)
(Acknowledge for the attribute data)
Dot pattern data stream is translated as follows:
Data stream
•••••••
AAAAAAAA BBBBBBBB
CCCCCCCC
1 byte•••••••
1 byte
1 byte
36 dots
12 dots
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
C
C
C
C
C
C
C
C
D
D
D
D
D
D
D
D
E
E
E
E
E
E
E
E
F
G
G
G
G
G
G
G
G
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
C
C
C
C
C
C
C
C
D
D
D
D
D
D
D
D
E
E
E
E
E
E
E
E
F
F
F
F
F
F
F
F
G
G
G
G
G
G
G
G
F
F
F
F
F
F
F
1/360 dpi
1/120 dpi
DRAFT
LQ
ESC ) # (27,41,#,
(1B,29,#,
40)H
Designates secondary font.
# = 0(30H) :
@
64)D
Copy the default secondary symbol set to the current secondary
symbol set.
# = 1(31H) :
Copy the default primary symbol set to the current secondary
symbol set.
# = 2(32H) :
Copy the current primary symbol set to the current secondary
symbol set.
# = 3(33H) :
Copy the default secondary font to the current secondary font.
8. Software commands
—
—
8-22
Download from Www.Somanuals.com. All Manuals Search And Download.
● HP Software commands
Code
Symbol
Function
Decimal
Hex
ESC ) s (27,41,115,#, (1B,29,73,#, Download font descriptor.
# W
DATA
87)D
DATA
57)H
DATA
ESC ) s 0 W command resistors a blank LQ font.
The format is as follows.
Byte 0-1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Byte 2-3
Byte 3-4
Byte 5-6
Byte 7-8
Byte 9-10
Byte 10-11
Byte 12-13
Byte 14-15
Byte 16-17
Byte 18-19
Byte 20-21
Byte 22-23
Byte 24-25
Byte 26-27
Byte 28-29
[ SYMBOL SET (2 BYTES)]
0
0
[ POINT SIZE (2 BYTES)]
0
0
0
0
0
[ TYPEFACE ]
0
0
0
[LQ/DRAFT]
Symbol set : Byte 14-15 represent the symbol set # and ID for the
download character to be selected by ESC ( # id command.
Example:Roman-8
8U”
32 x 8 + 85 - 64 = 277 (01H,15H)
Point size(character height): Point size in decimal is registered.
Typeface:Parameter used in the typeface selection command is
registered.
LQ/DRAFT:Print Quality, LQ or Draft is registered by the
following definition;
0:DRAFT 1:LQ
ESC * b (27,42,98,#, (1B,2A,62,#, Selects format the graphic data compression.
# M
77)D
4D )H
Available in PCL3+ or PCL3+D
Raster graphics data are registered.
# = 0 :compression off
# = 1 :mode 1
# = 2 :mode 2
# = 3 :mode
ESC * b (27,42,98,#, (1B,2A,62,#, Designates raster graphic data transmission.
# W
87)D
57)H
DATA
DATA
DATA
ESC * b (27,42,98,#, (1B,2A,62,#, Sets temporary graphics X-offset.
# X 88)D 58)H
ESC * b (27,42,98,#, (1B,2A,62,#, Sets temporary graphics Y-offset.
# Y 89)D 59)H
8. Software commands
—
—
8-23
Download from Www.Somanuals.com. All Manuals Search And Download.
G HP Software commands
Code
Symbol
Function
Decimal
Hex
ESC * c (27,42,99,#, (1B,2A,63,#, Set download character code.
# E 69)D 45)H
ESC * c (27,42,99,#, (1B,2A,63,#, Download font control
# F 70)D 46)H Controls download font as follows.
# = 0 (30H)
# = 3 (33H)
# = 6 (36H)
:Delete all download font
:Delete data of current download code.
:Copy ROM font to download font.
ESC * p (27,42,112,#, (1B,2A,70,#, Sets Horizontal positioning by dot
# X
88)D
58)H
# = 1/180" units :PCL3 or PCL3+
# = 1/360" units : PCL3+D
ESC * p (27,42,112,#,,(1B,2A,70,#, Sets Vertocal positioning by dot
# Y
89)D
59)H
# = 1/180" units :PCL3 or PCL3+
# = 1/360" units : PCL3+D
ESC * r (27,42,114,#, (1B,2A,72,#, Sets start raster graphics printing
# A
65)D
41)H
Raster graphics printing starts as follows
# = 0(30H) :Prints from the left most printable position
# = 1(31H) :Prints from the current position
Sets terminates rastergraphics printing
Raster graphics printing is terminated.
Model number request (Serial I/F only)
Model number is requested.
ESC * r (27,42,114, (1B,2A,72,
66)D 42)H
ESC * r (27,42,114, (1B,2A,72,
75)D 4B)H
B
K
The printer sends back the following answer when this data is
recognized. “2235A 2712CRLF”
ESC * r (27,42,114,#, (1B,2A,72,#, Designates raster graphics width.
# S 83)D 53)H Raster graphics width is defined by dot.
ESC * t (27,42,116,#, (1B,2A,74,#, Designates raster graphics resolution.
# R
82)D
52)H
Raster graphics resolution is defined as follows.
When PCL3+ or PCL3+D is selected.
# = 6 , 0 (36H,30H) :60 dpi
# = 9 , 0 (39H,30H) :90 dpi
# = 1 , 8 , 0 (31H,38H,30H) :180 dpi
# = 3 , 6 , 0 (33H,36H,30H) :360 dpi
When PCL3 is selected.
# = 9 , 0 (39H,30H):90 dpi
# = 1 , 8 , 0 (31H,38H,30H) :180 dpi
ESC 9
ESC =
ESC ?
DC1
(27)D (57)D (1B)H (39)H Clear left and right margin.
(27)D (61)D (1B)H (3D)H Half line feed - Half line feed is executed.
(27,63,17)D (1B,3F,11)H Request I/O status (Serial I/O only)
Printer status is requested.
The printer sends back the following data to the host computer as
the printer status.
MSB
6
0
LSB
2
7
0
5
0
4
0
3
1
0
1/0 1/0 1/0 1/0
Paper out or cover open
Printer busy
ONLINE (always)
I/O DATA error
:1
:1
:0
:1
ESC E
ESC Y
ESC Z
ESC z
(27)D (69)D (1B)H (45)H Reset - The printer is initialized.
(27)D (89)D (1B)H (59)H Designates display function - Display function is set on.
(27)D (90)D (1B)H (5A)H Cancels display function - Display function is set off.
(27)D (122)D (1B)H (7A)H Self test - Self test print is executed for 1 page.
8. Software commands
—
—
8-24
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Software setup functions
The commands shown below are valid only when the software setup
function is activated in the setup mode. If the software setup function is
not activated in the setup mode, these commands are processed as normal
data.
Software setup is activated when the setup start command is issued and
deactivated when the setup end command is issued.
When the setup start command is accepted, any other software commands
and print data are ignored until the setup end command is accepted.
If the printer setting is frequently changed by setup commands, use the
save disable command so as not to exceed the allowable number of retries
to write in the EEPROM, which is approximately 100 thousand.
Command format
( 1B,7C,60, m1,m2, a1,•••,ak )H
SETUP COMMAND
a1 ~ ak:Optional data
DATA NUMBER
= m1 + 256 x m2 [a1 ~ ak]
HEADER(START)
1. Setup start command
2. Setup end command
3. Save disable command
HD+DC1 (1B,7C,60,01,00,11)H
HD+DC2 (1B,7C,60,01,00,12)H
HD+DEL (1B,7C,60,01,00,7F)H
If this command is specified between the setup start command and
setup end command, the setting is not saved in the EEPROM
when the setup end terminates the software setup mode. It is
useful when the enlargement, reduction and other functions are
frequently used.
HD = 1BH,7CH,60H,m1,m2
* Commands (1) to (19) are not automatically reset when the setup is
quit after changing the setting.
— 9. Software setup functions —
9-1
Download from Www.Somanuals.com. All Manuals Search And Download.
● Command
Control code
Corresponding setup function
Code
Hexadecimal
HD + EM + n
(1B,7C,60,02,00,19,n)H
(1) Paper path specification (PAPER PATH key)
(Setup Function #61)
n = 00H Front loading and rear ejection of fanfold paper
01H Front loading and front ejection of manually inserted paper
02H CSF loading and front ejection (Optional)
10H Front loading and upward ejection of fanfold paper
11H Front loading and upward ejection of manually inserted paper
12H Front loading and rear ejection of manually inserted paper
13H CSF loading and upward ejection (Optional)
4H Rear loading and front ejection of fanfold paper (Optional)
It is recommended that manual rear ejection not be used
together with another paper path application. Paper path
switching and the paper path switching mechanism are not
guaranteed if there is paper in the paper path switching
mechanism.
See pages 1-6, 1-7 and 3-42.
HD + F + n
(1B,7C,60,02,00,46,n)H
(2) Paper format selection (PAPER FORM key)
n = 0: Selects format memory 1 (Memo 1)
n = 1: Selects format memory 2 (Memo 2)
n = 2: Selects format memory 3 (Memo 3)
n = 3: Selects format memory 4 (Memo 4)
n = 4: Selects format memory 5 (Memo 5)
n = 5: Selects format memory 6 (Memo 6)
This command selects the format memory to be used for
the currently selected paper path.
See pages 1-10 and 1-11.
HD + x + n
(1B,7C,60,02,00,78,n)H
(3) Character quality setting (QUALITY key)
n=0 LQ
(Setup Function #10)
1
2
3
4
5
6
7
DRAFT
LQ
NLQ
DRAFT
S. D.
S. S. D.
HQDR
This command specifies the character quality in the
currently selected format memory.
See page 3-17.
HD + +
(1B,7C,60,01,00,2B)H
(4) TOF position setting (TOF SET key)
This command is valid only when paper is loaded.
It specifies the TOF position of the loaded paper.
See page 2-3.
— 9. Software setup functions —
9-2
Download from Www.Somanuals.com. All Manuals Search And Download.
● Command
Control code
Corresponding setup function
Code
HD + @
Hexadecimal
(1B,7C,60,01,00,40)H
(1B,7C,60,02,00,47,n)H
(5) Reset (RESET key)
If the printer is reset without saving data, it enters the
condition set when power was turned on.
HD + G + n
(6) Printing pressure adjustment
(Setup Function #01)
n=0 Normal
See page3-8.
1
2
3
4
Normal
Dark 1
Dark 2
Auto
This command specifies the printing pressure in the
currently selected format memory.
HD + c + m+n
(1B,7C,60,03,00,63,
m,n)H
(7) Head gap adjustment
When m = 0,3 Auto mode
(Setup Function #02)
See page 3-9.
n=5
:
Auto: +5 click
:
n=1
n=0
n=255
n=254
Auto: +1 click
Auto: 0 click
Auto: -1 click
Auto: -2 click
When m = 1,4 Fixed mode
n=25
:
n=1
Fix: +25 click
:
Fix: +1 click
Fix: 0 click
Fix: -1 click
Fix: -2 click
:
n=0
n=255
n=254
:
n=251
Fix: -5 click
This command specifies the paper pressure in the currently
selected format memory.
When m=0,1: Paper thickness adjustment is performed
after the printing head moves to the specified position.
When m = 3,4: Paper thickness adjustment is performed
when the command is processed and the printing head does
not move.
HD + p + n1 + n2 (1B,7C,60,03,00,70,
n1,n2)H
(8) TOF position adjustment
(Setup Function #03)
n = n1 + 256 x n2
00 ≤ n ≤ 63
TOF: + n/60"
This command specifies the TOF position in the currently
selected format memory.
See page 3-10.
— 9. Software setup functions —
9-3
Download from Www.Somanuals.com. All Manuals Search And Download.
● Command
Control code
Corresponding setup function
Code
Hexadecimal
HD + C + m + n (1B,7C,60,03,00,43,m,n)H
(9) Page length setting
(Setup Function #04)
See page 3-11.
m = 0 Fanfold paper
m = 1 Cut sheet paper
m = 0
n = 00H 11.0"
01H 2.0"
02H 2.5"
03H 3.0"
04H 3.5"
05H 4.0"
06H 4.5"
07H 5.0"
08H 5.5"
09H 6.0"
n = 0AH 6.5"
0BH 7.0"
0CH 7.5"
0DH 8.0"
0EH 8.5"
0FH 9.0"
10H 9.5"
11H 10.0"
12H 10.5"
13H 11.0"
n = 14H 11.5"
15H 12.0"
16H 12.5"
17H 13.0"
18H 13.5"
19H 14.0"
1AH 14.5"
n = 1BH 15.0"
1CH 15.5"
1DH 16.0"
1EH 16.5"
20H 12.0"
m = 1
n = 0H A4 PORT
2H A4 PORT
n=12H A4
14H LETTER
15H LEGAL
16H A3
LAND
LAND
LAND
LAND
4H LETTER PORT
5H LEGAL PORT
6H A3
PORT
BH HALF LETTER PORT
CH EXECUTIVE PORT
1BH HALF LETTER
LAND
LAND
1CH EXECUTIVE
DH GOVERMENT LETTER PORT 1DH GOVERNMENT LETTER PORT
EH GOVERMENT LEGAL PORT 1EH GOVERNMENT LEGAL PORT
20H A5 PORT
30H A5
LAND
21H LEDGER PORT
22H POST CARD PORT
27H COM-10 PORT
28H COM-6 PORT
29H DL PORT
32H POST CARD
37H COM-10
38H COM-6
39H DL
LAND
LAND
LAND
LAND
LAND
LAND
LAND
2AH C5 PORT
3AH C5
2BH F4 PORT
3BH F4
2CH MONARCH PORT
3CH MONARCH
This command specifies the page length in the currently selected
format memory.
PORT : Portrait
LAND : Landscape
— 9. Software setup functions —
9-4
Download from Www.Somanuals.com. All Manuals Search And Download.
● Command
Control code
Corresponding setup function
Code
Hexadecimal
HD + W + n
(1B,7C,60,02,00,57,n)H
(10) Width of fanfold paper
(Setup Function #05)
See page 3-12.
n=0
1
15 inches
10 inches
2
5
inches
4
12 inches
This command is valid when m = 0 or fanfold paper is
specified in the page length setting (9) above.
This command specifies the paper width in the currently
selected format memory.
HD + T + 00H + n (1B,7C,60,03,00,54,
00, n)H
(11) Top margin
(Setup Function #06)
See page 3-13.
00 ≤ n ≤ 15
(In units of 6 lpi)
This command specifies the top margin in the currently
selected format memory.
HD + N + n
(1B,7C,60,02,00,4E,n)H
(12) Bottom margin
(Setup Function #07)
See page 3-14.
00 ≤ n ≤ 15
(In units of 6 lpi)
The perforation is not skipped when n=0. This command
specifies the bottom margin in the currently selected format
memory.
HD + Q + ml + mr
(1B,7C,60,03,00,51,
ml,mr)H
(13) Right and left margin
(Setup Function #08, #09)
See pages 3-15 and 3-16.
00 ≤ ml ≤ 63 Left margin
00 ≤ mr ≤ 63
Right margin
(In units of 10 cpi)
This command specifies the right and left margins in the
currently selected format memory.
— 9. Software setup functions —
9-5
Download from Www.Somanuals.com. All Manuals Search And Download.
● Command
Control code
Corresponding setup function
Code
Hexadecimal
HD + k + n
(1B,7C,60,02,00,6B,n)H
(14) Character font selection
(Setup Function #11)
See page 3-18.
n = 00H ROMAN
01H ROMAN
02H SANS SERIF
03H COURIER
04H PRESTIGE
05H SCRIPT
06H OCR-B
07H OCR-A
08H LETTER GOTHIC
09H ORATOR
0AH ORATOR-S
This command specifies the font in the currently selected
format memory.
HD + P + n
(1B,7C,60,02,00,50,n)H
(15) Character pitch selection
(Setup Function #12)
See page 3-19.
n=0
1
2
10
10
12
15
CPI
CPI
CPI
CPI
3
4
17.1 CPI
5
6
20
24
CPI
CPI
7
9
PROPORTIONAL
16.7 CPI
This command specifies the font in the currently selected
format memory.
HD + 3 + n
(1B,7C,60,02,00,33,n)H
(16) Line feed pitch setting
(Setup Function #13)
n=0
1
2
3
4
6
8
9
3
4
LPI
LPI
LPI
LPI
LPI
See page 3-20.
This command specifies the font in the currently selected
format memory.
— 9. Software setup functions —
9-6
Download from Www.Somanuals.com. All Manuals Search And Download.
● Command
Control code
Corresponding setup function
Code
Hexadecimal
HD + SI + n
(1B,7C,60,02,00,0F,n)H (17) Zoom in/out
(Setup Function #14)
n=00H
01H
100% n=10H 200% n=1AH 1200%
91%
02H
03H
04H
83%
79%
66%
n=12H 400% n=1CH 1400%
n=14H 600% n=1EH 1600%
0AH
0BH
0CH
116% n=16H 800%
120%
141% n=18H 1000%
This command specifies the zoom in/out in the currently
selected format memory.
See page 3-21.
HD + 4 + n
HD + ? + n
HD + Z + n
(1B,7C,60,02,00,34,n)H (18) Paper fastener
(Setup Function #15)
See page 3-22.
n=0
1
NO
YES
This command specifies the paper fastener mode in the
currently selected format memory.
(1B,7C,60,02,00,3F,n)H (19) Perforation head-up
(Setup Function #16)
See page 3-22.
n=0 NO
YES
1
This command specifies the perforation head-up mode in
the currently selected format memory.
(1B,7C,60,02,00,5A,n)H (20) Fanfold feed
(Setup Function #17)
See page 3-23.
n=0
1
FRICTION : NO
FRICTION : YES
This command specifies the fanfold feed in the currently
selected format memory.
— 9. Software setup functions —
9-7
Download from Www.Somanuals.com. All Manuals Search And Download.
● Command
Control code
Corresponding setup function
Code
Hexadecimal
HD + M + 01H + n (1B,7C,60,03,00,4D,
01,n)H
(21) Saving data in format memory
(Setup Function #19)
n=0
1
2
3
4
5
Saves data in format memory 1.
Saves data in format memory 2.
Saves data in format memory 3.
Saves data in format memory 4.
Saves data in format memory 5.
Saves data in format memory 6.
This command saves data in the currently selected format
memory into specified memory.
See page 3-24.
HD + M + 02H + n (1B,7C,60,03,00,4D,
02,n)H
(22) Loading data from format memory (Setup Function #20)
n=0
1
2
3
4
Loads from format memory 1.
Loads from format memory 2.
Loads from format memory 3.
Loads from format memory 4.
Loads from format memory 5.
Loads from format memory 6.
5
This command loads data from the specified memory into
the currently selected format memory.
See page 3-24.
HD + E + n
(1B,7C,60,02,00,45,n)H (23) Emulation selection
(Setup Function #20)
See page 3-25.
n=00H
01H
EPSON
IBM
02
HP
— 9. Software setup functions —
9-8
Download from Www.Somanuals.com. All Manuals Search And Download.
● Command
Control code
Corresponding setup function
Code
Hexadecimal
HD + t + m + n
(1B,7C,60,03,00,74,
m,n)H
(24) Character table selection
(Setup Function #21, #22, #23, #51)
See pages 3-25, 3-26 and 3-41.
m = 00H
EPSON
01H IBM
03H HP (PRIMARY FONT)
04H HP (SECONDARY FONT)
[m=00H: EPSON] [m=01H: IBM]
n = 0 Italic
n =0 Set 1
Set 2
1
2
3
Code page
Download
Code page
1
[m=03H: HP (PRIMARY FONT)]
n = 00 ROMAN-8 (8U)
01 CODE PG CODE PAGE
02 PC-8D/N PC-8 DENMARK/NORWAY(11U)
03 ECMA
04 LEGAL
ECMA LATIN 1 (ISO 8859-1, ON)
(HP SET, 1U)
05 SWEDEN1 (ISO-10, OS)
06 SWEDEN2 (ISO-11, 3S)
07 SPAIN
(ISO-17, 2S)
08 FRANCE (ISO-69, 1F)
09 GERMAN (ISO-21, 1G)
0A U.K.
(ISO-4, 1E)
0B PORTU
PORTUGAL (ISO-16,4S)
0C NORWAY1 (ISO-60, 4S)
0D NORWAY2(ISO-61, 1D)
0E IRV
0F ITALY
(ISO-2, 2U)
(ISO-15, 0I)
10 FRANC2 FRACE 2 (ISO-25, OF)
11 GERMN2 GERMAN 2 (HP SET, OG)
12 SPAIN2
13 SPAIN3
14 JAPAN
(ISO-85, 0G)
(HP-SET, 1S)
(ISO-14, 0K)
15 PORTU2 PORTUGAL (ISO-84, 5S)
[m=04H: HP (SECONDARY FONT)]
n = 00 LINE-DRAW
(0L)
01 MATH-7
(0M)
— 9. Software setup functions —
9-9
Download from Www.Somanuals.com. All Manuals Search And Download.
● Command
Control code
Corresponding setup function
Code
Hexadecimal
HD + R + n
(1B,7C,60,02,00,52,n)H
(25) National font selection (EPSON) (Setup Function #24)
n = 0H USA
8H
9H
Japan
Norway
1H France
2H Germany AH Denmark2
3H U.K. BH Spain2
4H Denmark CH Latin America
5H Sweden DH Korea
6H Italy
EH Turkey
7H Spain
FH Legal
See page 3-27.
HD + i + n
(1B,7C,60,02,00,69,n)H
(26) Code page selection
(Setup Function #25)
See page 3-28.
n = 0H 437
1H 850
(USA)
(Multilingual)
(Portuguese)
(Canadian French)
(Nordic)
3H 860
4H 863
5H 865
6H 857
(Turkish)
7H 858
8H 861
9H BRASCII
AH ABICOMP
20H ISO 8859-1
HD + Y + n
HD + 5 + n
(1B,7C,60,02,00,59,n)H
(1B,7C,60,02,00,35,n)H
(27) Alternate graphics mode (AGM) (IBM)
(Setup Function #26)
n = 0 Invalid
Valid
See page 3-28.
1
(28) CR code function
(Setup Function #27)
See page 3-29.
n = 0
CR only
1
2
CR + LF
AUTOFEED
HD + 6 + n
HD + 1 + n
(1B,7C,60,02,00,36,n)H
(29) LF code function
(Setup Function #28)
See page 3-29.
n = 0
1
LF only
CR + LF
(
1B,7C,60,02,00,31,n)H
(30) Accent character
(Setup Function #29)
n = 0
1
Simple (Resident Font)
Comp. (2 Pass Print)
See page 3-30.
— 9. Software setup functions —
9-10
Download from Www.Somanuals.com. All Manuals Search And Download.
● Command
Control code
Corresponding setup function
Code
Hexadecimal
HD + 0 + n
(1B,7C,60,02,00,30,n)H
(31) Zero font style
n = 0 No-slashed "0"
(Setup Function #30)
See page 3-30.
1
Slashed
"0"
HD + w + n
(1B,7C,60,02,00,77,n)H
(32) Horizontal tab interval
(Setup Function #31)
See page 3-31.
n =0
2
4
6
8
10
12
characters
characters
characters
characters
characters
characters
1
2
3
4
5
HD + > + a + n
HD + > + b + n
HD + > + c + n
HD + > + d + n
HD + > + f + n
HD + ] + m + n
(1B,7C,60,03,00,3E,
61, n)H
(33) Page length lock
(Setup Function #32)
See page 3-31.
n =0 NO
1
YES
(1B,7C,60,03,00,3E,
62, n)H
(34) Font lock
(Setup Function #33)
See page 3-32.
n =0 NO
YES
1
(1B,7C,60,03,00,3E,
63, n)H
(35) Character pitch lock
(Setup Function #34)
See page 3-32.
n =0 NO
1
YES
(1B,7C,60,03,00,3E,
64, n)H
(33) Character quality lock
(Setup Function #35)
See page 3-33.
n =0 NO
1
YES
(1B,7C,60,03,00,3E,
66, n)H
(36) Character table lock
(Setup Function #36)
See page 3-33.
n =0 NO
1
YES
(1B,7C,60,03,00,5D,
6D, n)H
(37) Validity of bar code and enlarged character
(Setup Function #40)
n=0
1
2
Mode 2
Ignored
Mode 1
See page 3-36.
— 9. Software setup functions —
9-11
Download from Www.Somanuals.com. All Manuals Search And Download.
● Command
Control code
Corresponding setup function
Hexadecimal
Code
HD + ] + n + n
(1B,7C,60,03,00,5D,
6E,n)H
(38) Bar code type
(Setup Function #41)
See page 3-37.
INDSTRAL-2.5 7H CODE128
INTRLVD-25
MATRIX-25
CODABAR
CODE11
n=0H
1H
8H EAN-8
9H EAN-13
AH UPC-A
2H
3H
4H
BH UPC-E
5H
6H
CODE39
CODE93
CH POSTNET
DH ELENENT
HD + ] + x + n
(1B,7C,60,03,00,5D,
78,n)H
(39) Bar code size
(Setup Function #42)
See page 3-39.
n= 0
1
1
1.5
2
2
3
2.5
HD + ] + X + n
(1B,7C,60,03,00,5D,
58,n)H
(40) Enlarged character size
(Setup Function #43)
See page 3-39.
n= 0
1
1
2
2
4
3
8
4
5
6
7
12
16
24
32
HD + A + n
(1B,7C,60,02,00,41,n)H
(41) Software setup
(Setup Function #44)
See page 3-40.
n=0
1
2
Valid
Ignored 1
Ignored 2
The setup command cannot change the ignored setting to
the valid setting. The command becomes valid after the setup
command mode is quit.
— 9. Software setup functions —
9-12
Download from Www.Somanuals.com. All Manuals Search And Download.
● Command
Control code
Corresponding setup function
Code
Hexadecimal
HD + < + e + n
(1B,7C,60,03,00,3D,
65,n)H
(42) PCL mode (HP)
(Setup Function #50)
See page 3-40.
n=0 PCL3+
1
2
PCL
PCL3+D
HD + o + m + n
(1B,7C,60,03,00,6F,
m,n)H
(43) Setting option
(Setup Function #60)
See page 3-41.
m=0 : CSF
n =0 : No CSF
1
: CSF used (with no rear tractor)
m=0 : Rear tractor
n =0 : No rear tractor
1
: Rear tractor used (with no CSF)
The CSF and rear tractor cannot be used together.
m=2 : Skew detection
(Setup Function #64)
n =0 : NO (No detection)
See page 3-43.
1
: YES (Detection)
m=3 : Paper jam detection (Setup Function #65)
n =0 : NO (No detection)
See page 3-44.
1
: YES (Detection)
HD + S + n
(1B,7C,60,02,00,53,
n)H
(44) Automatic scrolling
(Setup Function #62)
See page 3-42.
n=0 No scroll
1
2
3
4
5
0.5 second
1 second
5 seconds
10 seconds
15 seconds
HD + 8 + n
(1B,7C,60,02,00,38,n)H
(1B,7C,60,02,00,66,n)H
(45) Out-of-paper detection
(Setup Function #63)
See page 3-43.
n=0 No (No detection)
1
Yes (Detection)
HD + f + n
(46) Line feed speed
(Setup Function #66)
See page 3-44.
n=0 Normal
1 1/2
2 1/3
— 9. Software setup functions —
9-13
Download from Www.Somanuals.com. All Manuals Search And Download.
● Command
Control code
Corresponding setup function
Code
Hexadecimal
HD + I + p + n
(1B,7C,60,03,00,49,
70,n)H
(47) Interface
n = 0 Parallel
(Setup Function #70)
See page 3-46.
1
2
Serial
Auto
This setting becomes valid after the setup command
mode is terminated.
HD + I + 0 + DC0 + n (1B,7C,60,04,00,49,
30,10,n)H
(48) Printer select command
(Setup Function #71)
See page 3-47.
n = 0 Valid
1
2
Invalid
SLCT IN signal
This setting becomes valid after the setup command
mode is terminated.
HD + I + 1 + 0 + n (1B,7C,60,04,00,49,
31,30,n)H
(49) Parity bit (SERIAL I/F)
(Setup Function #72)
See page 3-47.
n = 0 None
1
2
Even
Odd
This setting becomes valid after the setup command
mode is terminated.
HD + I + 1 + 1 + n (1B,7C,60,04,00,49,
31,31,n)H
(50) Data length (SERIAL I/F)
(Setup Function #73)
See page 3-48.
n = 0 8 bits
1
7 bits
This setting becomes valid after the setup command
mode is terminated.
HD + I + 1 + 2 + n (1B,7C,60,04,00,49,
31,32,n)H
(51) Stop bit (SERIAL I/F)
(Setup Function #74)
See page 3-48.
n = 0 1 bit
1
2 bits
This setting becomes valid after the setup command
mode is terminated.
— 9. Software setup functions —
9-14
Download from Www.Somanuals.com. All Manuals Search And Download.
● Command
Control code
Corresponding setup function
Code
Hexadecimal
HD + I + 1 + 3 + n (1B,7C,60,04,00,49,
31,33,n)H
(52) Protocol (SERIAL I/F)
(Setup Function #75)
See page 3-49.
n = 0 DTR
1
2
3
X-ON/X-OFF 1
X-ON/X-OFF 2
ETX/ACK
This setting becomes valid after the setup command mode
is terminated.
HD + I + 1 + 4 + n (1B,7C,60,04,00,49,
31,34,n)H
(53) Baud rate (SERIAL I/F)
(Setup Function #76)
See page 3-49.
n = 0 38400 BPS
1
2
3
4
5
6
7
19200 BPS
9600
4800
2400
1200
600
BPS
BPS
BPS
BPS
BPS
BPS
300
This setting becomes valid after the setup command mode
is terminated.
HD + I + 1 + 5 + n (1B,7C,60,04,00,49,
31,35,n)H
(54) Operation in case of serial error (SERIAL I/F)
(Setup Function #77)
n = 0 Print "●"
See page 3-50.
1
Ignored
This setting becomes valid after the setup command mode
is terminated.
HD + I + 1 + DC0 + n (1B,7C,60,04,00,49,
31,10,n)H
(55) CTS signal (SERIAL I/F)
(Setup Function #78)
n = 0 YES (ENABLE)
See page 3-50.
1
NO
This setting becomes valid after the setup command mode
is terminated.
— 9. Software setup functions —
9-15
Download from Www.Somanuals.com. All Manuals Search And Download.
● Command
Control code
Corresponding setup function
Code
Hexadecimal
HD + I + 1 + DC1 + n (1B,7C,60,04,00,49,
31,11,n)H
(56) CD signal (SERIAL I/F)
(Setup Function #79)
See page 3-51.
n = 0 YES (ENABLE)
1
NO
This setting becomes valid after the setup command mode
is terminated.
HD + I + 1 + DC2 + n (1B,7C,60,04,00,49,
31,12,n)H
(57) DSR signal (SERIAL I/F)
(Setup Function #80)
See page 3-51.
n = 0 YES (ENABLE)
1
NO
This setting becomes valid after the setup command mode
is terminated.
HD + I + b + n
(1B,7C,60,03,00,49,
62,n)H
(58) Input buffer size
(Setup Function #81)
See page 3-52.
n = 0 64K byte
1
2
8K byte
128 byte
This setting becomes valid after the setup command mode
is terminated.
HD + I + 0 + 0 + n (1B,7C,60,04,00,49,
30,30,n)H
(59) BUSY/ACK signal timing (PARALLEL I/F)
(Setup Function #82)
n = 0 Type 3
See page 3-53.
1
2
Type 2
Type 1
This setting becomes valid after the setup command mode
is terminated.
HD + I + 0 + 1 + n (1B,7C,60,04,00,49,
30,31,n)H
(60) Input data latch timing (PARALLEL I/F)
(Setup Function #83)
n = 0 Type F.
See page 3-53.
1
Type R.
This setting becomes valid after the setup command mode
is terminated.
— 9. Software setup functions —
9-16
Download from Www.Somanuals.com. All Manuals Search And Download.
● Command
Control code
Corresponding setup function
Code
Hexadecimal
HD + I + 0 + 3 + n
(1B,7C,60,04,00,49,
30, 33,n)H
(61) Error status signal output
(Setup Function #84)
See page 3-54.
n = 0 YES
1
NO
HD + U + n
(1B,7C,60,02,00,55,n)H
(1B,7C,60,02,00,7A,n)H
(62) Printing direction
(Setup Function #90)
See page 3-55.
n = 0 Pre-direction
1
2
3
Pre-direction
Uni-direction
Bi-direction
HD + z + n
(63) Display language on LCD
(Setup Function #91)
See page 3-55.
n = 0 ENGLISH
1
2
3
4
DEUTSCH
FRANCAIS
ESPANOL
ITALIANO
HD + > + g + n
(1B,7C,60,03,00,3E,
67, n)H
(64) Locking panel keys other than RESET and
ONLINE keys in the online state
(Setup Function #92)
See page 3-56.
n = 0 NO
YES
1
HD + > + e + n
(1B,7C,60,03,00,3E,
65, n)H
(65) RESET key lock in the online state
(Setup Function #93)
n = 0 NO
See page 3-56.
1
YES
HD + SP + n1 + n2
(1B,7C,60,03,00,20,
n1, n2)H
(66) Print Head Position
n = n1
+
n2 x 256
Specifies the print head position in units of 1/360 inch
from the leftmost printable position.
The print head moves at the time that this command is
processed.
— 9. Software setup functions —
9-17
Download from Www.Somanuals.com. All Manuals Search And Download.
● Command
Control code
Corresponding setup function
Code
Hexadecimal
HD + q + n
(1B,7C,60,02,00,71,n)H
(67) Paper Quality
(Setup Function #18)
See page 3-23.
n = 0 GOOD
1
NO GOOD
HD + 2 + n
HD + # + n
(1B,7C,60,02,00,32,n)H
(1B,7C,60,02,00,23,n)H
(68) FF CODE AT TOF
(Setup Function #37)
See page 3-34.
n = 0 NO
1
YES
(69) Graphic Quality
(Setup Function #38)
See page 3-35.
n = 0 MODE 0
1
MODE 1
MODE 2
2
HD + S + FF + n
HD + e + n
(1B,7C,60,03,00,53,
FF,n)H
(70) Auto scroll position
(Setup Function #67)
See page 3-45.
n = 0 ANY POS
1
TOF ONLT
(1B,7C,60,02,00,65,n)H
(71) Sleep mode
(Setup Function #94)
See page 3-57.
n = 0 YES
1
NO
— 9. Software setup functions —
9-18
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Specifications
Printing specifications
Printing Method
Serial impact dot matrix
Print Head
24-pin movable (Parallel/Staggered orientation)
TM
Emulation
EPSON LQ-2550
IBM 2391
TM
TM
TM
Hewlett Packard Rugged Writer 480 (PCL3)
Bar code function
Enlarged character mode
Print Mode
10 cpi, 12 cpi, 15 cpi, 16.7 cpi, 17.1 cpi, 20 cpi, 24 cpi
Proportional printing
1/2 Proportional printing
Emphasized mode
Double striking mode
Double-width mode
Double-hight mode
Superscript & subscript mode
Italic mode
Download Character EPSON
IBM
HP
:
:
128 characters
32 KB
:
:
128 characters (PCL3), 255 characters (PCL3+, PCL3+D)
Character Table
EPSON
IBM
Italic set
Extended graphic set
Code Page 437 (USA), 850 (Multilingual),
:
857 (Turkish), 858, 860 (Portuguese), 861 (Icelandic),
863 (Canadian French), 865 (Nordic), ISO-8859-1
BRASCII, ABICOMP
(Code Page can be used in the EPSON or HP mode.)
ROMAN-8 (8U), PC-8 (10U), PC-850 (12U),
HP
:
ECMA 94, LATIN 1(ISO-8859-1,0N), PC-8 DENMARK/NORWAY (11U),
LINE-DRAW (0L,0B), MATH 7(0A,0M), ROMAN-EXTENSION (0E),
SWEDEN 2 (ISO-10,3S), SWEDEN (ISO-11,0S),
UK (ISO-4,1E), FRANCE 2 (ISO-25,0F), FRANCE (ISO-69,1F),
GERMAN 2 (0G), GERMAN (ISO-21,1G),ITALY (ISO-15,0I),
SPAIN 3 (1S), SPAIN (ISO-17,2S), SPAIN 2 (ISO-85,6S)
PORTUGAL (ISO-16,4S), PORTUGAL (ISO-84,5S), IRV (ISO-2,2U),
JAPAN (ISO-14,0K), ASCII (ISO-6,0U), LEGAL (1U)
Max. dots Dots/inch Vertical dots
11 types
Graphic Printing
EPSON
IBM
:
816
60
80
8/24
:
12 types
1088
1224
1632
8
8/24
8/24
90
120
120
180
240
360
360
1632
❈
8
2448
24
3264
4896
4896
❈
❈
❈
8
24
48(IBM mode)
❈Horizontally adjacent dots can not be printed.
4 raster graphic 60dpi, 90dpi, 180dpi, 360dpi
— 10. Specifications —
HP
:
10-1
Download from Www.Somanuals.com. All Manuals Search And Download.
❈ Print mode specifications
Print mode specifications
Max. No. Character Structure Print speed
Mulipart Dot pitch
mode (inch)
Print mode
(V × H)
(cps)
of Col.
×
Normal 1/120
Dark 1 1/120
Dark 2 1/180
Normal
Dark 1 1/144
Dark 2
Normal
Dark 1 1/180
Dark 2
Normal
Dark 1 1/240
Dark 2
Normal
Dark 1 1/240
Dark 2
12 12
603
474
316
569
432
432
712
473
473
526
399
399
540
411
411
631
481
481
577
379
379
×
10cpi
12cpi
15cpi
16.7cpi
17cpi
20cpi
24cpi
136
12 12
×
12 18
×
163
204
12 12
×
12 12
×
Draft
227 12 12(+2.4)
×
233
272
326
----
12 12(+2)
Normal
Dark 1 1/240
Dark 2
Normal
Dark 1 1/360
Dark 2
×
12 12
×
12 12(+3)
Normal
×
Proportional Dark 1 1/180
12
N
----
(IBM,HP)
Dark 2
Normal
Dark 1 1/120
Dark 2
Normal
Dark 1 1/120
Dark 2
Normal
Dark 1 1/360
Dark 2
Normal
Dark 1 1/360
Dark 2
723
569
569
904
712
712
180
79
×
Speed Draft
(SD)
12cpi
163
204
136
163
204
12 8(+2)
×
S.Speed Draft
(SSD)
15cpi
10cpi
12cpi
12
8
×
24 36
59
216
95
×
24 30
71
Letter
Quality
(LQ)
Normal
Dark 1 1/360
Dark 2
270
118
89
×
15cpi
(EPSON)
24 24
Normal
Dark 1 1/720
Dark 2
237
118
89
×
15cpi
(IBM,HP)
204 24 36(+12)
Normal
Dark 1 1/720
Dark 2
Normal
Dark 1 1/720
Dark 2
263
131
98
270
135
102
×
16.7cpi
17cpi
227
233
24 36(+7)
×
24 36(+6)
( ): Additional space
— 10. Specifications —
10-2
Download from Www.Somanuals.com. All Manuals Search And Download.
❈ Print mode specifications
Max. No. Character Structure Print speed
Mulipart
mode
Dot pitch
(inch)
Print mode
(V × H)
(cps)
of Col.
Normal
Dark 1 1/720
Dark 2
Normal
Dark 1 1/720
Dark 2
Normal
Dark 1 1/720
Dark 2
315
158
119
380
189
142
380
189
142
×
20cpi
272
24 30(+6)
×
24cpi
(EPSON)
326
326
----
24 24(+6)
Letter
Quality
(LQ)
×
24cpi
(IBM,HP)
24 30
Normal
Proportional Dark 1 1/360
×
×
24
24
N
N
----
----
Dark 2
Normal
Dark 1 1/720
1/2 Prop.
----
(EPSON) Dark 2
Normal
240
158
158
289
189
189
361
237
237
237
158
158
263
175
175
270
180
180
316
210
210
379
253
253
379
253
253
×
10cpi
12cpi
Dark 1 1/360
Dark 2
Normal
Dark 1 1/360
Dark 2
136
163
204
24 36
×
24 30
Normal
×
15cpi
(EPSON)
Dark 1 1/360
Dark 2
16 24
Normal
×
15cpi
(IBM,HP)
Dark 1 1/720
Dark 2
204 24 36(+12)
Normal
×
NLQ
16,7cpi
17cpi
Dark 1 1/720
Dark 2
Normal
Dark 1 1/720
Dark 2
227
233
272
326
326
----
24 36(+7)
×
24 36(+6)
Normal
×
20cpi
Dark 1 1/720
Dark 2
24 30(+6)
Normal
×
24cpi
(EPSON)
Dark 1 1/720
Dark 2
16 24(+6)
Normal
×
24cpi
(IBM,HP)
Dark 1 1/720
Dark 2
24 30
Normal
Proportional Dark 1 1/360
×
×
24
24
N
N
----
----
Dark 2
Normal
1/2 Prop.
Dark 1 1/720
----
(EPSON) Dark 2
( ): Additional space
— 10. Specifications —
10-3
Download from Www.Somanuals.com. All Manuals Search And Download.
❈ Print mode specifications
Max. No. Character structure Print speed
Mulipart
mode
Dot pitch
(inch)
Print mode
(V × H)
(cps)
of Col.
Normal
Dark 1 1/120
Dark 2
Normal
Dark 1 1/144
Dark 2
Normal
Dark 1 1/180
Dark 2
Normal
Dark 1 1/240
Dark 2
Normal
Dark 1 1/240
Dark 2
Normal
Dark 1 1/240
Dark 2
Normal
Dark 1 1/240
Dark 2
360
240
240
289
216
216
361
237
237
263
175
175
270
180
180
316
210
210
379
253
253
×
10cpi
136
24 36
×
12cpi
15cpi
163
204
24 12(+3)
×
24 12
×
HQDR
16.7cpi
17cpi
20cpi
24cpi
227 24 12(+2.3)
×
233
272
326
----
24 12(+2)
×
24 12
×
24 12(+3)
Normal
Proportional Dark 1 1/144
(IBM,HP) Dark 2
×
24
N
----
( ): Additional space
— 10. Specifications —
10-4
Download from Www.Somanuals.com. All Manuals Search And Download.
❈ specifications
Graphic printing specifications
Graphic type
Horizontal
dot pitch
1/60inch
Print
pitch
Normal
Print speed
inch/sec
31.6
Density
Pins
60dpi
8/24
Dark 1/2
Normal
Dark 1/2
Normal
Dark 1/2
Normal
Dark 1/2
Normal
Dark 1/2
Normal
Dark 1/2
Normal
Dark 1/2
Normal
Dark 1/2
Normal
Dark 1/2
Normal
Dark 1/2
Normal
Dark 1/2
Normal
Dark 1/2
Normal
Dark 1/2
Normal
Dark 1/2
24.0
24.0
18.0
18.0
15.8
18.0
10.5
36.0
24.0
31.6
24.0
18.0
10.5
24.0
18.0
36.0
24.0
18.0
10.5
36.0
24.0
18.0
10.5
24.0
18.0
36.0
24.0
80dpi
90dpi
8
8/24
8/24
8/24
8
1/80inch
1/90inch
1/120inch
1/60inch
1/60inch
1/120inch
1/90inch
1/60inch
1/120inch
1/60inch
1/120inch
1/90inch
1/60inch
120dpi
120dpi
(High speed 1,2)
120dpi
180dpi
24
24
24
8
180dpi
(High speed 1)
180dpi
(High speed 2)
240dpi
240dpi
8
(High speed 1,2)
360dpi
24
24
24
360dpi
(High speed 1)
360dpi
(High speed 2)
NOTE : High speed 1, Quality : NLQ
High speed 2, Quality : HQDR, DRAFT, S. D., S. S. D.
Throughput
Print Mode
Columns
Throughput
Draft (10cpi)
132
132
132
132
132
132
206 LPM
76 LPM
100 LPM
135 LPM
230 LPM
270 LPM
LQ pica (10cpi)
NLQ (10cpi)
HQDR (10cpi)
S. D. (12cpi)
S. S. D. (15cpi)
— 10. Specifications —
10-5
Download from Www.Somanuals.com. All Manuals Search And Download.
❈ specifications
Paper specifications
Major functions
-
-
-
-
-
-
-
-
-
-
High-speed printing
Available paper sizes
❈Fanfold paper Paper width: 3 ~ 16 inches (Front tractor)
3 ~ 16.5 inches ( Rear tractor)
Original plus 8 multipart forms printing
Bar code printing
Enlarged character printing
Zooming IN/OUT
Paper thickness: 0.08 ~ 0.12 mm
Paper weight:
55 ~ 90 kg
17 ~ 28 lbs
64 ~ 105 g/m
Built-in skew sensor
2
Automatic head adjustment
Perforation cutting
Paper quality:
Wood-free paper
Paper parking
❈Fanfold paper
Number of sheets: 9 or less (Dark 2)
Automatic perforation feeding (Automatic
scroll)
(multipart forms) Paper thickness: 0.12 ~ 0.59mm
Paper weight:
34 kg original +8
non-carbon equivalent
-
-
-
-
Dual paper parking (with rear tractor)
Setup memory setting
Vertical alignment
❈Cut sheet paper
Paper thickness: 0.08 ~ 0.12 mm
Energy Star
Paper weight:
55 ~ 90 kg
17 ~ 28 lbs
64 ~ 105 g/m
2
Interfaces
Parallel I/F (Centronics-compatible)
Paper quality:
Paper sizes:
Wood-free paper
A3, A4, A5, Letter,
Half letter, Legal
Bidirectional (IEEE1284, Nibble mode)
Serial I/F (RS-232C)
Executive, Ledger,
Government legal,
Government letter, F4
Protocol:
DTR, X-ON/X-OFF 1,
X-ON/X-OFF 2, ETX/ACK
Baud rate: 38400, 19200, 9600, 4800,
2400, 1200, 600, 300 (bps)
Max. dimensions: 420× 432 mm (W×L)
Min. dimensions: 76 × 76 mm (W×L)
: 512k byte maximum
Data buffer size
❈Post card
❈Envelope
Commercial-6,10
Monarch
Other specifications
DL,C5
❈Power supply:
AC 120V, 60Hz for USA and Canada
AC 230V, 50Hz for Europe and Asia
❈Power consumption: 200 watts (Draft, LQ Self Test)
45 watts (Standby)
Paper loading method
Fanfold paper:
Tractor:
Push tractor
14 watts (Sleep mode)
Front tractor (standard)
Rear tractor (option)
❈Optional parts power
source:
5 V, 1.5 A
❈Operating temp.:
❈Operating humidity: 20 to 80% (No condensation)
5 to 40°C [41 to 104°F]
Option: Rear Tractor
❈MTBF:
10,000 hours (at 25% duty; Not
applicable to print head.)
Cut sheet paper
Friction type feeding
Manual, CSF (option)
:
630 × 395 × 250 mm (W × D × H)
[24.8 × 15.6 × 9.8 inch]
Dimensions
Option: Cut Sheet Feeder
Multipart printing capability (LQ)
Standard mode:
Dark 1 mode:
Dark 2 mode:
Original sheet + 5 sheets
Original sheet + 7 sheets
Original sheet + 8 sheets
:
Approximately 24 kg [52.9 lbs.]
Weight
These modes are selectable with #1 MULTIPART in
.
the SETUP MODE
Line feed speed: 83 lines per second (6 lines/inch)
The line feed speed is selectable with #66 LF
SPEED in the EXTENDED SETUP MODE.
Line feed pitch: 1/360 inch minimum
— 10. Specifications —
10-6
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Character set table
EPSON Italic table
H
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
L
(0)
(16) (32) (48) (64) (80)
(96) (112) (128) (144) (160) (176) (192) (208) (224) (240)
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
(15)
(31) (47) (63) (79) (95)
(111) (127) (143) (159) (175) (191) (207) (223) (239) (255)
Select this character table with ESC t 0.
EPSON Extended graphic table
H
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
L
(0)
(16) (32) (48) (64) (80)
(96) (112) (128) (144) (160) (176) (192) (208) (224) (240)
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
(15)
(31) (47) (63) (79) (95)
(111) (127) (143) (159) (175) (191) (207) (223) (239) (255)
Select this character table with ESC 6 and ESC t 1.
— 11. Character set table —
11-1
Download from Www.Somanuals.com. All Manuals Search And Download.
G Character set table
EPSON international font table
HEX
23 24 40 5B 5C 5D 5E 60 7B 7C 7D 7E
Country
U.S.A
FRANCE
GERMANY
U.K
DENMARK
SWEDEN
ITALY
SPAIN
JAPAN
NORWAY
DENMARK2
SPAIN2
LATIN AMERICA
KOREA
TURKEY
LEGAL
Select this character table with ESC R.
IBM character set table 1
H
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
L
(0)
(16) (32) (48) (64) (80)
(96) (112) (128) (144) (160) (176) (192) (208) (224) (240)
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
(15)
(31) (47) (63) (79) (95)
(111) (127) (143) (159) (175) (191) (207) (223) (239) (255)
Select this character table with ESC 7.
— 11. Character set table —
11-2
Download from Www.Somanuals.com. All Manuals Search And Download.
G Character set table
IBM character set table 2
H
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
L
(0)
(16) (32) (48) (64) (80)
(96) (112) (128) (144) (160) (176) (192) (208) (224) (240)
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
(15)
(31) (47) (63) (79) (95)
(111) (127) (143) (159) (175) (191) (207) (223) (239) (255)
Select this character table with ESC 6.
IBM all-character set table
H
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
L
(0)
(16) (32) (48) (64) (80)
(96) (112) (128) (144) (160) (176) (192) (208) (224) (240)
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
(15)
(31) (47) (63) (79) (95)
(111) (127) (143) (159) (175) (191) (207) (223) (239) (255)
— 11. Character set table —
11-3
Download from Www.Somanuals.com. All Manuals Search And Download.
G Character set table
(Common)
Code 00H ~ 7FH
Code page 437 (U.S.A.)
Code page 850 (Multilingual)
Code page 857 (Turkish)
— 11. Character set table —
11-4
Download from Www.Somanuals.com. All Manuals Search And Download.
G Character set table
Code page 858 (Multilingual-Euro)
Code page 860 (Portuguese)
Code page 861 (Icelandic)
Code page 863 (Canadian French)
— 11. Character set table —
11-5
Download from Www.Somanuals.com. All Manuals Search And Download.
G Character set table
Code page 865 (Nordic)
BRASCII
ABICOMP
ISO-1 (ISO-8859-1)
— 11. Character set table —
11-6
Download from Www.Somanuals.com. All Manuals Search And Download.
G Character set table
HP mode
ROMAN-8 character set
PC-8 (Danish / Norwegian) character set
L/H
0
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
L/H
0
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
A
B
C
D
E
F
A
B
C
D
E
F
The (00)H-(1F)H and (7F)H normally function as control code.
LEGAL character set
MATH 7 character set
L/H
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
L/H
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
The character of (A0)H-(FF)H are, respectively, the same as those
of (20)H -(7F)H.
The character of (A0)H-(FF)H are, respectively, the same as those
of (20)H -(7F)H.
— 11. Character set table —
11-7
Download from Www.Somanuals.com. All Manuals Search And Download.
G Character set table
L/H
0
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
The character of (A0)H-(FF)H are, respectively, the same as those of (20)H -(7F)H.
23 24 40 5B 5C 5D 5E 60 7B 7C 7D 7E
ISO ID
0U
69 1F
0F
ASCII
6
FRANCE
FRANCE 2
-
GERMANY 21 1G
GERMANY 2
U.K.
-
0G
1E
4
SWEDEN
11 0S
SWEDEN 2 10 3S
ITALY
15 0I
17 2S
85 6S
SPAIN
SPAIN 2
SPAIN 3
JAPAN
NORWAY
-
1S
14 0K
60 0D
NORWAY 2 61 1D
PORTUGAL 16 4S
PORTUGAL 2 84 5S
IRV
2
2U
•The character of (A0)H-(FF)H are, respectively, the same as those of (20)H -(7F)H.
•The characters with (20)H-(7F)H codes which are not shown in the International character
set above are the same as those of (20)H -(7F)H in ROMAN-8.
— 11. Character set table —
11-8
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
IBM character set table 2 ..................11-3
IBM all-character set table .................11-3
Code page 437 ..................................11-4
Code page 850 ..................................11-4
Code page 857 ..................................11-4
Code page 858 ..................................11-5
Code page 860 ..................................11-4
Code page 861 ..................................11-6
Code page 863 ..................................11-5
Code page 865 ..................................11-5
Code page 858 ..................................11-5
ISO-8859-1 ........................................11-6
Code page BRASCII .........................11-6
Code page ABICOMP .......................11-6
ROMAN-8 ..........................................11-7
PC-8 (Danish/Norwegian) .................11-7
LEGAL ...............................................11-7
MATH 7 .............................................11-7
LINE DRAW ......................................11-8
Internatinal character set (ISO) .........11-8
Components and functions ........................viii, ix
Connecting the printer to the computer
Parallel interface ................................1-28
Serial interface ..................................1-29
Connector
Symbol
,
,
,
Key............................3-2
A
Accent character.............................................3-30
ALT key ............................................................2-4
Alternate graphics mode (AGM) (IBM) ...........3-28
AUTO FEED signal ................................3-29, 7-3
Automatic scrolling .................................3-42, 4-4
Automatic serial/parallel ................................7-11
B
Bar code function
Code 128 subset transition rule .........5-11
Setting HRI print ...........................5-3, 5-9
Setting HRI font ...................................5-4
Printing density .................................... 5-5
Error processing ................................5-10
Element width ......................................5-3
Guard bar expansion ...........................5-5
Outline of the bar code function ..........5-1
Beginning of sequence ........................5-4
End of sequence .................................5-5
Data processing in the bar code
Parallel ................................................7-1
Serial ...................................................7-5
Consumables ..................................................xii
Control panel ..............................................x, 2-1
CR code function ...........................................3-29
Cut sheet paper
data sequence ................................5-7
Start and stop characters ....................5-6
Check character ..................................5-4
Bar code data sequence .....................5-5
Bar code rotational angle ....................5-6
Bar code height ..........................3-39, 5-3
Value input mode ................................5-6
Bar code type .............................3-37, 5-2
Buffer size .....................................................3-49
Printing area ........................................1-9
Loading (Manual paper feeding) .......1-19
Printing using the CSF ......................1-22
D
Dark .......................................................i, 3-8, 4-2
Default setting .................................................3-6
Dimensions .......................................................vii
Disabled printing area
Top margin .........................................3-13
Bottom margin ....................................3-14
Left margin .........................................3-15
Right margin .......................................3-16
Dual paper packing .......................................1-16
C
Cable
Parallel interface ..................................7-1
Serial interface ....................................7-5
Caution ..............................................................iv
Character font ...............................................3-18
Character pitch .............................................3-19
Character table
Selecting character table (EPSON) ...3-26
Selecting character table (IBM) .........3-26
Selecting character table (HP) ..........3-25
Selecting code page ..........................3-28
Selecting national font (EPSON) .......3-27
Selecting secondary
E
EEPROM initialization ....................................4-5
EJECT/LOAD key ...........................................2-3
Enlarged character function
character table (HP) ....................3-41
EPSON italic table ..............................11-1
EPSON extended graphic table .........11-1
EPSON international font table .........11-2
IBM character set table 1 .................11-2
Character pitch ..................................5-23
HMI ....................................................5-21
VMI ...................................................5-22
Setting and canceling underscores ....5-26
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
All-character set ...............................5-20
Form feeding .....................................5-18
Line feeding .......................................5-17
Rotational angle ................................5-24
Initializing the enlarged character
mode ...........................................5-18
Setting and canceling the enlarged
character mode ...........................5-22
Selecting an enlarged character font...5-20
Vertical printing position .................... 5-27
Horizontal printing position ................5-26
Setting and canceling enlarged
I
Improving printing capability ............................3-8
Installing ribbon cassette ................................1-2
Interface specifications
Parallel interface ..................................7-1
Serial interface ....................................7-5
K
Key shortcut functions ....................................4-9
character smoothing ......................5-25
Cell offset ...........................................5-23
Cell expansion ...................................5-19
Height expansion ...............................5-21
Top offset ...........................................5-25
Back spacing ......................................5-17
Carriage returning ..............................5-18
Arrangement .......................................5-19
Character quality ................................5-24
Width expansion .................................5-26
Print samples ......................................5-28
Enlarging/Reducing print ..............................3-21
ENTER key .....................................................3-2
Executing test printing ....................................4-9
EXIT key .........................................................3-2
L
LF code function ............................................3-29
Line feed pitch ...............................................3-20
Line feed speed .............................................3-44
LINE FEED/REVERSE LF key ........................2-4
Liquid crystal display ..............................1-10, 2-5
Loading date from format memory ...............3-24
Locking panel keys .......................................3-56
Locking reset key ..........................................3-56
M
Major functions .................................................... i
Manual
Paper path ....................................1-5, 2-2
Selecting paper path ..................1-7, 3-42
Loading ..............................................1-19
Page length .......................................3-11
Max. No. of column .......................................10-2
MICRO LF/MICRO RLF key ...........................2-4
F
Factory default setting .....................................3-6
Fanfold paper
Paper path ....................................1-4, 2-2
Selecting paper path ...........1-6, 1-7, 3-42
Printing area ........................................1-8
Loading (Front tractor) .......................1-12
Loading (Rear tractor) .......................1-16
Page length .......................................3-11
Paper width .......................................3-12
Feeding perforation to the cutter
N
National font (EPSON) ..................................3-27
O
position .............................2-1, 4-3
Operating humidity .......................................10-6
Operating temperature .................................10-6
Operational error messages
FORM FEED key .............................................2-4
Functional error massages
CARRIAGE ERROR ............................6-1
FAN ERROR ...................................... 6-1
F.S. ERROR ........................................6-1
T.S. ERROR ........................................6-1
HAI. S. ERROR ...................................6-1
HA. S. ERROR ....................................6-2
HOME S. ERROR ...............................6-2
PLEASE POWER OFF ........................6-2
HEAD PROTECTION ......................... 6-2
PARK ERROR .....................................6-2
PAPER OUT ERROR ..........................6-3
PAPER JAM ERROR ..........................6-3
SKEW ERROR ....................................6-4
FRONT COVER OPEN .......................6-4
PAPER PATH ERROR..........................6-4
H. ADJ: FIX ERROR ...........................6-4
FLAP SWITCHING ERROR..................6-5
JAM. S LEVEL ERR .............................6-5
Options ..............................................................xii
H
High-speed printing ...............................4-1, 10-2
Horizontal tab ...............................................3-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Serial error .........................................3-50
CTS signal ..................................3-50, 7-6
CIN ....................................3-52, 7-8, 7-11
CD signal .....................................7-7, 3-51
CRN .................................3-52, 7-8, 7-11
DSR signal .................................3-51, 7-6
DTR protocol ..............................3-49, 7-8
DTR signal ...........................................7-7
EXT/ACK protocol .....................3-49, 7-11
RXD signal ..........................................7-6
RTS signal ...........................................7-7
TXD signal ..........................................7-7
SRTS signal .......................................7-7
X-ON/X-OFF (I)/(II) protocol .......3-49, 7-9
Setting the printing start position .....................4-2
Setup modes
Outline .................................................3-1
Key type ..............................................3-2
Factory defaults setting .......................3-6
Setting example ...................................3-3
Saving data in format memory ..........3-24
Printing setup list ................................3-57
Enter/Exit ......................................3-1, 3-3
Loading data from format memory ....3-24
Skew detection .............................................3-43
Software command
P
Paper ..............................................................1-8
PAPER FORM key .........................................2-4
Paper jam detection ......................................3-44
PAPER PATH key ..........................................2-2
Parallel interface
AUTO FEED signal .............................7-3
ACK signal ..........................................7-4
BUSY signal ........................................7-4
ERROR signal .....................................7-4
INITIAL signal ......................................7-3
PE signal .............................................7-4
SELECT signal ....................................7-4
SELECT IN signal ...............................7-3
STROBE signal ...................................7-3
Data latch timing ................................3-53
Timing chart
Data input .....................................7-2
Initialization ..................................7-2
Power consumption ......................................10-6
Power cord ................................................vi, 1-1
Print head .....................................................viii, ix
Print mode specifications ...............................10-2
Printing area .............................................1-8, 1-9
Printing direction ............................................3-55
Print method ..................................................10-1
Printing out
EPSON ...............................................8-1
IBM ......................................................8-9
HP .....................................................8-18
Bar code .............................................5-2
Enlarged character function ..............5-16
Software setup ..............................................3-40
Command ............................................9-2
Setup functions ....................................9-1
Specifications ...............................................10-1
Smudging paper ...................................6-6
Correcting vertical misalignment .......... 4-6
Printing speed ...............................................i, 4-1
Q
QUALITY key ..................................................2-3
T
R
TEAR OFF key ...............................................2-1
Throughput ...............................................i, 10-5
TOF SET key ...................................................2-3
Top of form (TOF) adjustment ................3-10, 4-2
Troubleshooting ...............................................6-1
RESET key .....................................................2-1
S
S.D. (Speed Draft)........................................... 4-1
S.S.D. (Super Speed Draft) .............................4-1
Saving data in format memory ......................3-24
Selecting emulation .......................................3-25
Selecting interface .........................................3-46
Selecting paper path .......................................1-6
Setting option .................................................3-41
Setting serial interface
U
Unpacking ..................................................... v, vi
Using various types of paper .................1-10, 4-8
W
Weight ...........................................................10-6
Parity bit ............................................3-47
Data length ........................................3-48
Stop bit ..............................................3-48
Protocol .............................................3-49
Baud rate ...........................................3-49
Z
Zero font with slash .......................................3-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Software command list
Code
Symbol
Function
Decimal
Hexadecimal
Activates the printer buzzer.
BEL
(07)D
(07)
Moves the printing position left by one character
Moves the printing position to the following horizontal tab
Single-line feed
Vertical tab
Form feed
Carriage return
Double-width printing on a single line
Specifies condensed mode.
Printer select
Cancels condensed mode.
Printer deselect
Cancels the double-width mode established by the SO command.
Cancel
Deletes a character
Escape
BS
HT
LF
VT
FF
CR
SO
SI
DC1
DC2
DC3
DC4
CAN
DEL
ESC
(08)D
(09)D
(10)D
(11)D
(12)D
(13)D
(14)D
(15)D
(17)D
(18)D
(19)D
(20)D
(24)D
(127)D
(27)D
(08)H
(09)H
(0A)H
(0B)H
(0C)H
(0D)H
(0E)H
(0F)H
(11)H
(12)H
(13)H
(14)H
(18)H
(7F)H
(1B)H
ESC SO
ESC SI
ESC EM
ESC SP
ESC !
ESC #
ESC $
ESC %
ESC &
(27)D(14)D
(27)D(15)D
(27)D(25)D
(27)D(32)D
(27)D(33)D
(27)D(35)D
(27)D(36)D
(27)D(37)D
(27)D(38)D
(27)D(42)D
(27,40,45)D
(27,40,94)D
(27,40,116)D
(27)D(43)D
(27)D(45)D
(27)D(47)D
(27)D(48)D
(27)D(50)D
(27)D(51)D
(27)D(52)D
(27)D(53)D
(27)D(54)D
(27)D(55)D
(27)D(58)D
(27)D(60)D
(27)D(61)D
(27)D(62)D
(27)D(63)D
(27)D(64)D
(27)D(65)D
(27)D(66)D
(27)D(67)D
(1B)H (0E)H Double-width printing on a single line
(1B)H (0F)H Specifies condensed mode.
(1B)H (19)H Specifies the paper path.
(1B)H (20)H Specifies the space between characters.
(1B)H (21)H Batch printing mode selection.
(1B)H (23)H Cancels MSB control.
(1B)H (24)H Specifies the absolute printing position.
(1B)H (25)H Specifies or cancels a downloaded character set
(1B)H (26)H Defines a downloaded character.
(1B)H (2A)H Selects a graphic function.
.
ESC
✽
ESC ( -
ESC ( ^
ESC ( t
ESC +
ESC -
(1B,28,2D)H Specifies a line type.
(1B,28,5E)H All character set
(1B,28,74)H Specifies a character set.
(1B)H (2B)H Specifies line feed pitch of n/360 inch.
(1B)H (2D)H Specifies or cancels underscoring.
(1B)H (2F)H Selects the vertical tab channel.
(1B)H (30)H Specifies 1/8-inch line feed pitch.
(1B)H (32)H Specifies 1/6-inch line feed pitch.
(1B)H (33)H Specifies line feed pitch of n/180 inch.
(1B)H (34)H Specifies the italic font.
(1B)H (35)H Cancels the italic font.
(1B)H (36)H Expands the character code area.
(1B)H (37)H Cancels the expanded character code area.
ESC /
ESC 0
ESC 2
ESC 3
ESC 4
ESC 5
ESC 6
ESC 7
ESC :
ESC <
ESC =
ESC >
ESC ?
ESC @
ESC A
ESC B
ESC C
(1B)H (3A)H Copies the internal character set
(1B)H (3C)H Returns to the home position.
(1B)H (3D)H Specifies MSB 0.
.
(1B)H (3E)H Specifies MSB 1.
(1B)H (3F)H Converts graphic modes.
(1B)H (40)H Initializes the printer.
(1B)H (41)H Specifies the line feed pitch in units of n/60 inch.
(1B)H (42)H Specifies the vertical tab position
.
(1B)H (43)H Specifies the page length in number of lines.
(1B,43,00)H Specifies the page length in inches.
(1B)H (44)H Specifies the horizontal tab position.
ESC C NUL (27,67,00)D
ESC D (27)D(68)D
Download from Www.Somanuals.com. All Manuals Search And Download.
● EPSON command list
Code
Symbol
Function
Decimal
Hexadecimal
ESC E
ESC F
ESC G
ESC H
ESC J
ESC K
ESC L
ESC M
ESC N
ESC O
ESC P
ESC Q
ESC R
ESC S
ESC T
ESC U
ESC W
ESC Y
ESC Z
ESC \
ESC a
ESC b
ESC g
ESC j
ESC k
ESC l
ESC p
ESC q
ESC t
ESC w
ESC x
(27)D(69)D
(27)D(70)D
(27)D(71)D
(27)D(72)D
(27)D(74)D
(27)D(75)D
(27)D(76)D
(27)D(77)D
(27)D(78)D
(27)D(79)D
(27)D(80)D
(27)D(81)D
(27)D(82)D
(27)D(83)D
(27)D(84)D
(27)D(85)D
(27)D(87)D
(27)D(89)D
(27)D(90)D
(27)D(92)D
(27)D(97)D
(27)D(98)D
(27)D(103)D
(27)D(106)D
(27)D(107)D
(27)D(108)D
(27)D(112)D
(27)D(113)D
(27)D(116)D
(27)D(119)D
(27)D(120)D
(1B)H (45)H
(1B)H (46)H
(1B)H (47)H
(1B)H (48)H
(1B)H (4A)H
(1B)H (4B)H
(1B)H (4C)H
(1B)H (4D)H
(1B)H (4E)H
(1B)H (4F)H
(1B)H (50)H
(1B)H (51)H
(1B)H (52)H
(1B)H (53)H
(1B)H (54)H
(1B)H (55)H
(1B)H (57)H
(1B)H (59)H
(1B)H (5A)H
(1B)H (5C)H
(1B)H (61)H
(1B)H (62)H
(1B)H (67)H
(1B)H (6A)H
(1B)H (6B)H
(1B)H (6C)H
(1B)H (70)H
(1B)H (71)H
(1B)H (74)H
(1B)H (77)H
(1B)H (78)H
Specifies emphasized printing.
Cancels emphasized printing
Specifies double-striking.
Cancels double-striking.
Executes line feeding at a pitch of n/180 inch.
Specifies the 8-dot single-density graphic mode.
Specifies the 8-dot double-density graphic mode.
Specifies 12 cpi (elite).
Specifies the bottom margin.
Cancels the bottom margin.
Specifies 10 cpi.
Specifies the right margin
.
Selects a national character type.
Specifies superscript or subscript.
Cancels superscript or subscript.
Specifies or cancels uni-directional printing.
Specifies or cancels double-width printing.
Specifies the 8-dot double-speed, double-density graphic mode.
Specifies the 8-dot quadruple-density graphic mode.
Specifies the relative printing position.
Selects the printing position adjustment.
Specifies the vertical tab position in each channel.
Selects 15 cpi.
Executes reverse feeding at a pitch of n/180 inch
Selects the font
.
.
Specifies the left margin.
Specifies or cancels proportional printing.
Selects a special effect.
Selects a character code table.
Specifies or cancels double-length printing.
Selects character quality.
Download from Www.Somanuals.com. All Manuals Search And Download.
● IBM command list
Code
Symbol
Function
Decimal
Hexadecimal
BEL
BS
(07)D
(07)H
Activates the printer buzzer.
(08)D
(08)H
Moves the printing position to the left by one character.
Moves the printing position to the next horizontal tab.
Single-line feeding
HT
(09)D
(09)H
LF
(10)D
(0A)H
VT
(11)D
(0B)H
Vertical tab
FF
(12)D
(0C)H
Form feed (Always moves the printing position to the left margin.)
Carriage return
CR
(13)D
(0D)H
SO
(14)D
(0E)H
Double-width printing on a single line
Specifies condensed mode.
SI
(15)D
(0F)H
DC1
DC2
DC4
CAN
ESC
ESC EM
(17)D
(11)H
Printer select
(18)D
(12)H
Cancels the condensed mode.
Cancels the double-width mode set by the SO command.
Cancel
(20)D
(14)H
(24)D
(18)H
(27)D
(1B)H
Escape
(27)D (25 )D
(27)D (42 )D
(27)D (45 )D
(27)D (48 )D
(27)D (49 )D
(27)D (50 )D
(27)D (51 )D
(27)D (51 )D
(27)D(52)D
(27)D(53)D
(27)D(54)D
(27)D(55)D
(27)D(58)D
(27)D(61)D
(27)D(65)D
(27)D(65)D
(27)D(66)D
(27)D(67)D
(1B)H (19)H
(1B)H (2A)H
(1B)H (2D)H
(1B)H (30)H
(1B)H (31)H
(1B)H (32)H
(1B)H (33)H
(1B)H (33)H
(1B)H (34)H
(1B)H (35)H
(1B)H (36)H
(1B)H (37)H
(1B,3A,00)H
(1B)H (3D)H
(1B)H (41)H
(1B)H (41)H
(1B)H (42)H
(1B)H (43)H
(1B,43,00)H
(1B)H (44)H
(1B)H (45)H
(1B)H (46)H
(1B)H (47)H
(1B)H (48)H
(1B)H (49)H
(1B)H (4A)H
(1B)H (4A)H
Specifies the paper path.
ESC
ESC
●
Selects a graphic function.
—
Specifies or cancels underscoring.
Specifies line feeding at 1/8-inch pitch.
Specifies line feeding at 7/72-inch pitch.
Executes ESC A.
ESC 0
ESC 1
ESC 2
ESC 3
ESC 3
ESC 4
ESC 5
ESC 6
ESC 7
ESC :
Specifies n/216-inch line feed pitch.
Specifies n/180-inch line feed pitch. (AGM)
Specifies TOF.
Specifies or cancels automatic line feeding
Specifies character set 2.
Specifies character set 1.
Specifies 12 cpi.
.
ESC =
ESC A
ESC A
ESC B
ESC C
Specifies downloading.
Specifies the line feed pitch in units of n/72 inch.
Specifies the line feed pitch in units of n/60 inch. (AGM)
Specifies the vertical tabs.
Specifies the page length in number of lines.
Specifies the page length in inches.
Specifies the horizontal tabs.
ESC C NUL (27,67,00)D
ESC D
ESC E
ESC F
ESC G
ESC H
ESC I
ESC J
ESC J
(27)D (68 )D
(27)D(69)D
(27)D(70)D
(27)D(71)D
(27)D(72)D
(27)D(73)D
(27)D(74)D
(27)D(74)D
Specifies emphasized printing.
Cancels emphasized printing.
Specifies double-striking.
Cancels double-striking.
Selects the font.
Executes line feeding at a pitch of n/216 inches.
(AGM)
Executes line feeding at a pitch of n/180 inches.
Download from Www.Somanuals.com. All Manuals Search And Download.
● IBM command list
Code
Symbol
Function
Decimal
Hexadecimal
ESC K
ESC L
ESC N
ESC O
ESC P
ESC Q
ESC R
ESC S
ESC T
ESC U
ESC W
ESC X
ESC Y
ESC Z
ESC [ -
(27)D(75)D
(27)D(76)D
(27)D(78)D
(27)D(79)D
(27)D(80)D
(27)D(81)D
(27)D(82)D
(27)D(83)D
(27)D(84)D
(27)D(85)D
(27)D(87)D
(27)D(88)D
(27)D(89)D
(27)D(90)D
(27,91,45)D
(1B)H (4B)H
(1B)H (4C)H
(1B)H (4E)H
(1B)H (4F)H
(1B)H (50)H
(1B)H (51)H
(1B)H (52)H
(1B)H (53)H
(1B)H (54)H
(1B)H (55)H
(1B)H (57)H
(1B)H (58)H
(1B)H (59)H
(1B)H (5A)H
(1B, 5B, 2D)H
(1B, 5B, 40)H
(1B, 5B, 4B)H
(1B, 5B,49)H
(1B, 5B, 54)H
(1B, 5B, 5C)H
Specifies the 8-dot single-density graphic mode.
Specifies the 8-dot double-density graphic mode.
Specifies the bottom margin.
Cancels the bottom margin.
Specifies or cancels proportional printing.
Printer deselect
Initializes horizontal and vertical tab positions.
Specifies superscript or subscript.
Cancels superscript or subscript.
Specifies or cancels uni-directional printing.
Specifies or cancels double-width printing.
Specifies the right and left margins.
Specifies the 8-dot double-speed double-density graphic mode.
Specifies the 8-dot quadruple-density graphic mode.
Specifies the line type.
ESC [ @ (27,91,64)D
ESC [ K (27,91,75)D
Specifies or cancels the double-width, double-height printing.
Software initial
ESC [ I
ESC [ T
ESC [ \
ESC [ d
ESC [ g
ESC \
(27,91,73)D
(27,91,84)D
(27,91,92)D
Selects the font.
Selects the code page.
Specifies the basic amount of line feeding.
Selects the character quality.
(27,91,100)D (1B, 5B, 64)H
(27,91,103)D (1B, 5B, 67)H
Graphic mode
(27)D (92)D
(27)D (93)D
(27)D (94)D
(27)D (95)D
(27, 100)D
(27, 106)D
(1B)H (5C)H
(1B)H (5D)H
(1B)H (5E)H
(1B)H (5F)H
(1B)H (64)H
(1B)H (6A)H
All-character set
ESC ]
Reverse line feeding
ESC ^
All-character set for a single character
Specifies or cancels the upper line.
Specifies the relative printing position.
Stops printing.
ESC _
ESC d
ESC j
Download from Www.Somanuals.com. All Manuals Search And Download.
● HPcommand list
Code
Symbol
Decimal
Function
Hexadecimal
BEL
BS
HT
LF
(07)D
(08)D
(09)D
(10)D
(12)D
(13)D
(14)D
(15)D
(27)D
(32)D
(127)D
(07)H
Activates the printer buzzer. (PCL3+ or PCL3+D)
Backspace one character.
Moves to next horizontal tab.
Linefeeds after printing.
Form feeds after printing.
Carriage return after printing.
Selects secondary font.
Selects prinmary font.
Designate start of escape sequence.
Space one character.
(08)H
(09)H
(0A)H
(0C)H
(0D)H
(0E)H
(0F)H
(1B)H
(20)H
(7F)H
FF
CR
SO
SI
ESC
SP
DEL
To print the ASCII DEL character.
ESC & a # C (27,38,97,#,67)D
ESC & a # H (27,38,97,#,72)D
ESC & a # L (27,38,97,#,76)D
ESC & a # M (27,38,97,#,77)D
ESC & a # R (27,38,97,#,82)D
ESC & a # V (27,38,97,#,86)D
(1B,26,61,#,43)H Horizontal positioning by column.
(1B,26,61,#,48)H Horizontal positioning by 1/720”.
(1B,26,61,#,4C)H Sets left margin.
(1B,26,61,#,4D)H Sets light margin.
(1B,26,61,#,52)H Vertical positioning by line (VMI).
(1B,26,61,#,56)H Vertical positioning by 1/720”.
ESC & d # D (27,38,100,#,68)D (1B,26,64,#,44)H Designates underline mode.
ESC & d # @ (27,38,100,#,64)D (1B,26,64,#,40)H Cancels underline mode.
ESC & k # E (27,38,107,#,69)D (1B,26,6B,#,45)H Designates/Cancels the auto-cancellation of
underline.
ESC & k # F (27,38,107,#,70)D (1B,26,6B,#,46)H Designates/Cancels the auto-cancellation of
secondary font.
ESC & k # G (27,38,107,#,71)D (1B,26,6B,#,47)H Designates line termination.
ESC & k # H (27,38,107,#,72)D (1B,26,6B,#,48)H Sets HMI (Horizontal motion index).
ESC & k # S (27,38,107,#,83)D (1B,26,6B,#,53)H Designates character pitch.
ESC & k # V (27,38,107,#,86)D (1B,26,6B,#,56)H Designates/Cancels automatic scroll mode.
ESC & k # W (27,38,107,#,87)D (1B,26,6B,#,57)H Controls print direction. (PCL3+ or PCL3+D)
ESC & l # A (27,38,108,#,65)D (1B,26,6C,#,41)H Designates paper size.
ESC & l # C (27,38,108,#,67)D (1B,26,6C,#,43)H Sets VMI (Vertical motion index).
ESC & l # D (27,38,108,#,68)D (1B,26,6C,#,44)H Sets the line spacing. VMI (Vertical motion index)
ESC & l # E (27,38,108,#,69)D (1B,26,6C,#,45)H Sets top margin by VMI.
ESC & l # F (27,38,108,#,70)D (1B,26,6C,#,46)H Sets text length.
ESC & l # H (27,38,108,#,72)D (1B,26,6C,#,48)H Sets paper path.
ESC & l # L (27,38,108,#,76)D (1B,26,6C,#,4C)H Designates/Cancels skip perforation mode.
ESC & l # P (27,38,108,#,80)D (1B,26,6C,#,50)H Sets page length by VMI.
ESC & p # X (27,38,112,#,88)D (1B,26,70,#,58)H Receives data as text.
ESC & s # C (27,38,115,#,67)D (1B,26,73,#,43)H Designates/Cancels wraparound.
ESC ( id
ESC ) id
(27,40,id)D
(27,41,id)D
(1B,28,id)H
(1B,29,id)H
Assign font to the primary/secondary font set.
ESC ( # @ (27,40,#,64)D
(1B,28,#,40)H
(1B,28,30,58)H
(1B,29,30,58)H
Designates primary font.
Assigns the download font to the current
primary/secondary font.
ESC ( 0 X
ESC ) 0 X
(27,40,48,88)D
(27,41,48,88)D
ESC ( s # B (27,40,115,#,66)D (1B,28,73,#,42)H Bold or emphasized.
ESC ) s # B (27,41,115,#,66)D (1B,29,73,#,42)H
Download from Www.Somanuals.com. All Manuals Search And Download.
● HP command list
Code
Symbol
Decimal
Function
Hexadecimal
ESC ( s # H (27,40,115,#,72)D (1B,28,73,#,48)H
ESC ) s # H (27,41,115,#,72)D (1B,29,73,#,48)H
ESC ( s # P (27,40,115,#,80)D (1B,28,73,#,50)H
ESC ) s # P (27,41,115,#,80)D (1B,29,73,#,50)H
ESC ( s # Q (27,40,115,#,81)D (1B,28,73,#,51)H
ESC ) s # Q (27,41,115,#,81)D (1B,29,73,#,51)H
ESC ( s # S (27,40,115,#,83)D (1B,28,73,#,53)H
ESC ) s # S (27,41,115,#,83)D (1B,29,73,#,53)H
Sets character spacing.
Selects proportional or fixed character spacing.
Sets print quality.
Sets italic character.
ESC ( s # T
ESC ) s # T
(27,40,115,#,84)D (1B,28,73,#,54)H
(27,41,115,#,84)D (1B,29,73,#,54)H
Sets typeface.
ESC ( s # U (27,40,115,#,85)D (1B,28,73,#,55)H
ESC ) s # U (27,41,115,#,85)D (1B,29,73,#,55)H
ESC ( s # V (27,40,115,#,86)D (1B,28,73,#,56)H
ESC ) s # V (27,41,115,#,86)D (1B,29,73,#,56)H
ESC ( s # W (27,40,115,#,87)D (1B,28,73,#,57)H
Sets super/subscript.
Sets character point size.
Download character descriptor and data.
Designates secondary font.
ESC ) # @
(27,41,#,64)D
(1B,29,#,40)H
ESC ) s # W (27,41,115,#,87)D (1B,29,73,#,57)H
Download font descriptor.
ESC * b # M (27,42,98,#,77)D
ESC * b # W (27,42,98,#,87)D
ESC * b # X (27,42,98,#,88)D
ESC * b # Y (27,42,98,#,89)D
ESC * c # E (27,42,99,#,69)D
ESC * c # F (27,42,99,#,70)D
(1B,2A,62,#,4D)H Selects format the graphic data compression.
(1B,2A,62,#,57)H
(1B,2A,62,#,58)H
(1B,2A,62,#,59)H
(1B,2A,63,#,45)H
(1B,2A,63,#,46)H
Designates raster graphic data transmission.
Sets temporary graphics X-offset.
Sets temporary graphics Y-offset.
Set download character code.
Download font control.
ESC * p # X (27,42,112,#,88)D (1B,2A,70,#,58)H
ESC * p # Y (27,42,112,#,89)D (1B,2A,70,#,59)H
Sets Horizontal positioning by dot.
Sets Vertocal positioning by dot.
Sets start raster graphics printing.
Sets terminates rastergraphics printing.
Model number request (Serial I/F only).
Designates raster graphics width.
Designates raster graphics resolution.
Clear left and right margin.
Half line feed.
Request I/O status.
Reset - The printer is initialized.
Designates display function.
Cancels display function - Display function is
set off.
ESC * r # A
ESC * r B
ESC * r K
ESC * r # S
ESC * t # R
ESC 9
(27,42,114,#,65)D (1B,2A,72,#,41)H
(27,42,114,66)D
(27,42,114,75)D
(1B,2A,72,42)H
(1B,2A,72,4B)H
(27,42,114,#,83)D (1B,2A,72,#,53)H
(27,42,116,#,82)D (1B,2A,74,#,52)H
(27)D (57)D
(27)D (61)D
(27,63,17)D
(27)D (69)D
(27)D (89)D
(27)D (90)D
(1B)H (39)H
(1B)H (3D)H
(1B,3F,11)H
(1B)H (45)H
(1B)H (59)H
(1B)H (5A)H
ESC =
ESC ? DC1
ESC E
ESC Y
ESC Z
ESC z
(27)D (122)D
(1B)H (7A)H
Self test - Self test print is executed for 1
page.
Download from Www.Somanuals.com. All Manuals Search And Download.
Maschinenlärminformationsverordnung 3. GSGV, 18.01.1991:
Der arbeitsplatzbezogene Schalldruckpegel beträgt 70 dB(A) oder weniger gemäß ISO 7779.
This unit complies with the Low Voltage Directive 73/23/EEC and the EMC Directive
89/336/EEC.
Dies Gerät entspricht den Bedingungen der Niederspannungs-Vorschrift 73/23/EEC und dem
EMVG nach 89/336/EEC.
THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS B LIMITS FOR
RADIO NOISE EMISSIONS FROM DIGITAL APPARATUS AS SET OUT IN THE
RADIO INTERFERENCE REGULATIONS OF THE CANADIAN DEPARTMENT OF
COMMUNICATIONS.
LE PRÉSENT APPAREIL NUMÉRIQUE N'ÉMET PAS DE BRUITS
RADIOÉLECTRIQUES DÉPASSANT LES LIMITES APPLICABLES AUX
APPAREILS NUMÉRIQUES DE CLASSE B PRESCRITES DANS LE RÈGLEMENT
SUR LE BROUILLAGE RADIOÉLECTRIQUE ÉDICTÉ PAR LE MINISTÈRE DES
COMMUNICATIONS DU CANADA.
Download from Www.Somanuals.com. All Manuals Search And Download.
|
