Plasma HDTV
50”TVHD de Plasma
Owner’s Manual Table of Contents
4
Manual del usuario Tabla de contenido 21
DP50719
Model No.:
/
No. de Modelo:
© 2009 Sanyo Manufacturing Corporation
Part No. / No. de parte : 1JC6P1P0337- -
Download from Www.Somanuals.com. All Manuals Search And Download.
THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING
RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.
A
FCC INFORMATION
TRADEMARKS
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN!
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installa-
tion. This equipment generates, uses and can radiate radio fre-
quency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio com-
munications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one
or more of the following measures:
Manufactured under license from Dolby Laboratories.
“Dolby” is a trademark of Dolby Laboratories.
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS
UNIT.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
HDMI, the HDMI Logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of
HDMI Licensing LLC.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
IMPORTANT SAFETY INSTRUCTIONS
“As an Energy Star® Partner, Sanyo
Manufacturing Corporation has deter-
mined that this product meets the Energy
Star® guidelines for energy efficiency.”
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
15. If an outside antenna is connected to the television
equipment, be sure the antenna system is grounded so
as to provide some protection against voltage surges
and built up static charges. In the U.S. Selection 810-21
of the National Electrical Code provides information with
respect to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an antenna
discharge unit, size of grounding conductors, location of
antenna discharge unit, connection to grounding elec-
trodes, and requirements for the grounding electrodes.
– Reorient or relocate the receiving antenna.
4. Follow all instructions.
– Increase the separation between the equipment and receiver.
This symbol on the nameplate means
the product is Listed by Underwriter’s
Laboratories Inc. It is designed and
manufactured to meet rigid U.L. safety
standards against risk of fire, casualty
and electrical hazards.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
– Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for
help.
CAUTION: FCC Regulations state that improper modifications
or unauthorized changes to this unit may void
the user’s authority to operate the unit.
16. An outside antenna system should not be located in the
vicinity of overhead power lines or other electrical light
or power circuits, or where it can fall into such power
lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from
touching such power lines or circuits as contact with
them might be fatal.
This Class B digital apparatus complies with Canadian
ICES-003.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding-type plug has two
blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided
plug does not fit fully into your outlet, consult an electri-
cian for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
PC RESOLUTION CHART
EXAMPLE OF ANTENNA GROUNDING ACCORDING
TO NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
SANYO recommends keeping the TV set at its
factory settings or moving Energy Saver settings
from “Level 1” to “Level 2” or “Level 3” to further
reduce power requirements and increase energy
savings. Doing so contributes to the sustainability
of our resources and environment.
11. Only use attachments/accessories specified by the
manufacturer.
“Note to CATV system installer:
This reminder is provided to call the CATV system installer’s attention to
Article 820-40 of the NEC that provides guidelines for proper grounding
and, in particular, specifies that the cable ground shall be connected to
the grounding system of the building, as close to the point of cable entry
as practical.”
12. Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the appara-
tus. When a cart is used, use caution
when moving the cart/apparatus com-
bination to avoid injury from tip-over.
SPECIFICATIONS
Power Requirement: Source – AC 120V, 60Hz
17. Wall or Ceiling Mounting—The product should be
mounted to a wall or ceiling only as recommended by
the manufacturer.
18. Apparatus shall not be exposed to dripping or splashing
and no objects filled with liquids, such as vases, shall be
placed on the apparatus.
19. Where the Mains plug is used as the disconnect device,
the disconnect device shall remain readily operable.
20. A warning that an apparatus with Class1 construction
shall be connected to a Mains socket outlet with a
protective earthing connection.
AC Power Consumption: 464 watts
13.Unplug this apparatus during lightning storms or when
unused for long periods of time.
Weight: 84 lbs.
14. Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
Dimensions: WIDTH
HEIGHT
DEPTH
DP50719
w/o stand
49.0
33.1
30.3
14.2
4.7
NOTE: Dimensions are in inches
Need help?
1-800-877-5032
Need help?
1-800-877-5032
2
3
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
PROTECTING THE PLASMA
SCREEN
The screen can be damaged if it is not maintained
properly. Do not use hard objects such as hard
cloth or paper. Do not use exces-
sive pressure when cleaning the
Plasma screen; excessive pressure
can cause permanent discoloration
or dark spots.
STAND REMOVAL AND WALL
MOUNTING (OPTIONAL)
Tools Needed: Phillips screwdriver No. 3
IMPORTANT NOTE:
Place HDTV face down on a padded or cushioned
surface that is larger than the screen size to
protect the screen and finish. Handling by more
than two people is recommended.
GETTING STARTED
BATTERY INSTALLATION
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . 2
FCC INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
TRADEMARKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
THINK GAIA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
DISPOSAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
PROTECTING THE LCD SCREEN . . . . . . . . . . . . . . . . . . . . . .3
PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
STAND REMOVAL / WALL MOUNTING . . . . . . . . . . . . . . .5
Install batteries in the remote control
( 2 “AAA”, not included)
PRECAUTIONS
To ensure safe operation, please
observe the following precautions:
Wall mounting of the HDTV must be performed
by a skilled person.
• Replace both batteries at the same
time. Do not use a new battery
with a used battery.
NEVER spray liquids on the screen.
Remove four (4) screws from the metal bracket.
CAUTION: Hold the stand firmly as you
remove the last screw.
GETTING STARTED—
HANDLING PRECAUTIONS
• Handle by the cabinet only. Never touch the
screen when handling.
1
2
• There’s a risk of explosion if a battery is replaced by
an incorrect type.
Remote Control Battery Installation . . . . . . . . . . . . . . . .5
Antenna Connections for off-air or cable . . . . . . . . . . .5
Universal Remote Control operation . . . . . . . . . . . . . . .6
Carefully remove the stand.
• Do not expose the Remote Control unit to moisture
or heat.
PC CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
PC MENU OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
BACK PANEL JACKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
AUDIO / VIDEO CONNECTIONS . . . . . . . . . . . . . . . . . . . . . .9
POWER CONNECTION / INITIAL CHANNEL SEARCH . .10
• Handle the Plasma HDTV carefully. Handling by
more than two people is recommended.
• Be sure to match the “+” and “–” signs on the
batteries with marks inside the remote control.
• Handling damage is not covered under warranty.
POSITIONING PRECAUTIONS
ON-SCREEN MENU OPERATION—
Chanel Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Channel Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Channel Scan Memory . . . . . . . . . . . . . . . . . . . . . . . .11
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Menu Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Digital Caption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
V-Chip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Energy Saver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Clock Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Light Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Panel Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
HDMI Linking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Manual Picture Settings . . . . . . . . . . . . . . . . . . . . . . .15
aaSound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Place this Plasma HDTV as indicated here.
•
Failure to do so may result in a fire hazard.
Allowing the proper amount of space at the top,
sides, and rear of the Plasma HDTV cabinet is
critical for proper air circulation and cooling of
the unit. If the Plasma HDTV is to be built into
a compartment or similarly enclosed, these
minimum distances must be maintained.
ANTENNA CONNECTION FOR
OFF-AIR SIGNALS OR CABLE
Use the screws that are threaded into four (4)
of the six (6) inserts on the back of your
Plasma HDTV to secure it to a wall mounting
kit (not included.)
3
ANTENNA
UNIVERSAL standard interface:
480 x 200 and 480 x360
Do not cover the ventilation slots on the Plasma
HDTV. Heat build-up can reduce the life of your
Plasma HDTV, and can be dangerous.
•
ANALOG / DIGITAL
ANTENNA IN
Mounting screws measurements:
M6 Diameter, Length—18mm (max.)
If Plasma HDTV is not to be used for an extended
period of time, unplug it from the power outlet.
•
Manual Sound Settings . . . . . . . . . . . . . . . . . . . . . . . .16
PHOTO VIEWER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
CABLE
The tuner in this HDTV can receive:
• Digital and Analog off air signals from an antenna
• Analog or ClearQAM cable channels from a direct
Cable TV connection.
Minimum space required
Need help?
1-800-877-5032
Need help?
1-800-877-5032
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
PC CONNECTIONS AND SETUP
REMOTE CONTROL OPERATION
PC Setting
Auto Adjustment – Automatically adjusts display
position, dot clock and phase.
Use your HDTV as a computer monitor by hooking
up your PC or Laptop to the TV with the use of an
appropriate monitor cable.
Before connecting any cables, disconnect the
AC power cords of both the HDTV and PC from
the AC outlets.
Dot Clock – Adjust the Dot frequency to match
your computer’s Dot frequency.
Phase – Adjust this parameter when the picture
appears to flicker or is blurred.
Power on the HDTV and any other peripheral
equipment before powering on the computer.
H-Position – Move the image horizontally
V-Position – Move the image vertically
To avoid an “Out of Range” condition please set
your PC’s output resolution to one compatible with
your HDTV. See PC Resolution chart on page 3.
Power Saving – Enable the HDTV to turn to
Standby Mode when computer is not in use.
NOTE: If computer has only DVI Output, a DVI to RGB
converter will be required (not included.)
RGB OUTPUT
JACK
DVI OUTPUT
JACK
HDTV BACK
Stereo mini
audio cable
PC SETTING SCREEN
PC OR LAPTOP
PC Picture and Sound
Standard – Sets predetermined values to the
Picture or Sound parameters.
RGB Monitor
cable
Sanyo recommends using
monitor cable that
includes a Ferrite Core.
a
Manual – Adjust Contrast, Brightness, and Color
Temperature screen settings, and the Bass and
Treble audio settings.
Laptop Display on HDTV
When using your Sanyo HDTV to display a
Laptop’s screen display, holding down the Fn (or
FN) key while pressing the appropriate function
key (F5, F7, F8, etc) should cycle through different
display modes between the laptop and the HDTV.
Modes may include displaying only on the laptop
screen, on both the laptop and the HDTV, or dis-
playing only on the HDTV.
Hold down
and press
PC PICTURE AND SOUND SCREENS
NOTE: Fn key and function key symbols on the laptop’s
keyboard may vary from one brand to another.
NOTE: These settings do not affect normal TV viewing.
Need help?
1-800-877-5032
Need help?
1-800-877-5032
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
BACK PANEL JACKS
AUDIO / VIDEO CONNECTIONS
HDMI INPUT1, 2 & 3 are used to hookup HD
digital devices such as a Blu-ray player, HD
Cable Box, HD Satellite Receiver or Video-
game System.
Digital Audio Output is used to hookup a
multichannel receiver with the use of a phono-
type digital audio cable.
Component connections will accept SDTV,
EDTV and HDTV video signals. Use them for
great image quality from digital devices.
HDMI (DVI) INPUT1 can be used to hookup
a DVI device with the use of an appropriate
adapter. (VIDEO3 Audio in L/R jacks need to
be hooked up to the DVI device as well)
MULTICHANNEL
RECEIVER
DVD PLAYER
(or similar device)
SATELLITE RECEIVER
(or similar device)
DVI
Component Video Input (VIDEO2 or VIDEO3)
Green (Y), blue (Pb), and red (Pr) Video inputs plus
the white and red Audio inputs.
1 USB Input
5
View pictures stored in a USB flash drive.
2
3
Analog / Digital Antenna Input
Stereo Audio Out (L/R) Jacks
6
7
HDMI (INPUT1, 2 & 3)
Composite Video Input (VIDEO1)
Yellow (Video), plus white and red (Audio) inputs.
An all digital AV interface that can accept
uncompressed video signals for the very best
picture possible.
8
9
Digital Audio Output (Coaxial)
S-Video Input (VIDEO1)
NOTE: An S-Video connection will override
connection to the Video1 (yellow) input jack.
NOTE: A DVI conection is possible via the HDMI (DVI)
INPUT1 jack using an appropriate adapter and
connecting the audio to the VIDEO3 Audio jacks.
a
4
PC Input and Stereo Audio (Mini)
USB FLASH
DRIVE
• MONITOR RGB (D-SUB)
• AUDIO R/L (Stereo Mini Jack)
STEREO AMPLIFIER
Optimum
High Definition
Standard
High Definition
USB input jack is used
to connect a USB mass
storage device to watch
JPEG images.
VCR
(or analog
device)
Composite
S-Video
Composite connections are used to hookup
your analog equipment such as a VCR or an
older DVD player.
H D M I
Audio Output L/R are used to hookup an
external stereo Amplifier. (Do not connect
external speakers directly to the HDTV)
Component
S-Video connection can replace the yellow
Video connection for enhanced video.
Above Standard
NOTE: Composite, S-Video, and Component video connections need their appropriate white and
red audio connections. High Definition image available from HD signals and HD equipment.
NOTE: Audio/Video cables are not supplied
Need help?
1-800-877-5032
Need help?
1-800-877-5032
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ON-SCREEN MENU OPERATION
CHANNEL SETTING
GETTING STARTED— INITIAL CHANNEL SEARCH (FIRST POWER ON)
Display the On Screen menu and use the
CURSOR LM keys to select Channel
Setting. Press ENTER.
Plug in AC power cord
120V AC, 60Hz
CHANNEL SEARCH
Turn On TV
Wait for on-screen instructions to
perform an Initial Channel Search.
Auto – Searches the detected mode, Cable or Air.
MAIN MENU SCREEN
CHANNEL SETTING SCREEN
CHANNEL SCAN MEMORY SCREEN
Cable – Searches for analog and unscrambled
(ClearQAM) digital cable channels.
INITIAL SETUP SCREEN
CHANNEL SEARCH
Checks Antenna and Cable signals
connected to the Antenna terminal.
Air (Antenna) – Searches for analog and digital off-air
channels.
DIgital Air Add-On – Searches digital off-air channels
adding newly found digital channels to the channel
map database.
NOTE: “Auto” detects the mode detection, Cable or Air, first,
and then proceeds with the channel search.
NOTE: Digital Air Add-On option is not available when the
current mode is Cable.
AV SEARCH
Searches for signals from devices
connected to the AV input jacks.
CHANNEL SEARCH METHOD SCREEN
Note: Power ON external devices connected to the TV before
CHANNEL SCAN MEMORY
Channel Scan Memory lists all Analog and Digital
channels found. It also lists Analog channels that were
not found, which can be added.
comencing an AV Search.
An AV search will begin if no Antenna signals are
detected, if neither of these searches detect signals,
the HDTV will tune to input Video1.
Move the channel select bar through all
channels, enabled and disabled.
Move the channel select bar through
enabled channels, skipping all disabled
channels.
CHANNEL SEARCH PROGRESS SCREEN
ON SCREEN HELP MENU
Access an on screen trouble shooting
guide (in the Initial Setup Screen.)
Enable a disabled channel or disable an
enabled one. A check mark indicates the
channel is enabled.
IMPORTANT FACT: This HDTV maintains only
one database of digital channels. Therefore,
when you search for cable channels, the data-
base of antenna digital channels will be deleted.
NOTE: You may acces the On Screen Help
menu later on at any time via the main
menu.
You will only be able to receive those ClearQAM
channels your cable company provides.
NOTE: For information on local digital channels,
Need help?
1-800-877-5032
Need help?
1-800-877-5032
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
ON-SCREEN MENU OPERATION
SETUP
ON-SCREEN MENU OPERATION
SETUP
Display the On Screen menu and use the
CURSOR LM keys to select Setup. Press
ENTER.
V – CHIP
Use this feature to automatically block programs with
content you deem as inappropriate for viewing by your
children.
Use the Setup menu to set the Menu Language,
V-Chip rating settings, customize Digital Captions, set
Energy Saver level, set the current time and on-time
with the Clock Timer, establish the HDMI Linking CEC
function, activate Light Sensor, and access the Panel
Protection feature.
Note: This feature is designed to comply with the United
States of America’s FCC V-Chip regulations. Therefore,
it may not function with broadcasts that originate in
other countries.
MAIN MENU SCREEN
SETUP V-CHIP SCREEN
Navigate the cursor
(highlight.)
MENU LANGUAGE
Choose between English, Spanish and French for your
On Screen menu’s display language. Press ENTER on
the desired language.
Make selection.
Block or unblock the selected
Rating option.
A blue marker indicates the current
selected option.
NOTE: Blocking a rating will automatically block all higher
ratings. Unblocking a rating automatically unblocks
all lower ratings.
ADJUST (STANDARD) SCREEN
SETUP MENU LANGUAGE SCREEN
DIGITAL CAPTION
Advanced V-Chip System
Captioning is textual information transmitted along
with the picture and sound. Turning Captioning ON
causes the HDTV to open these captions (digital or
analog) and superimpose them on the screen.
This feature is an advanced Regional rating system for
digital channels.
When the HDTV detects compatible Rating Region
Table (RRT) data, it’s downloaded & stored in memory.
NOTE: Local broadcasters decide which caption signals
to transmit.
The Setup V-Chip screen is then modified to show the
Adjust (Advanced) option.
Digital Caption’s Font, Background and Foreground
display may be customized:
Use the CURSOR LM and ꢀ ꢁ keys to highlight the
different options. Use the ENTER key to block or
unblock the selected rating.
DIGITAL CAPTION SCREEN
Navigate the cursor
(highlight.)
MORE INFORMATION
Select / set parameter.
Additional information about MPAA (Motion Picture
Association of America) and V-Chip rating can be
respectively.
ADJUST (ADVANCED) SCREENS
(Setup Menu operations continued on page 14.)
Need help?
1-800-877-5032
Need help?
1-800-877-5032
12
13
Download from Www.Somanuals.com. All Manuals Search And Download.
ON-SCREEN MENU OPERATION
SETUP
ON-SCREEN MENU OPERATION
PICTURE
Display the On Screen menu and use the
CURSOR LM keys to select Picture.
Press ENTER.
ENERGY SAVER
Energy saver settings control the LCD backlight
brightness to save power consumption.
You may choose between Movie, Sports, News,
Game, and Standard, which have predetermined fixed
picture parameter values, or one of the two Manual
options for customized personal settings.
The higher the level number, the more brightness
reduction and higher power saving.
ENERGY SAVER SCREEN
MAIN MENU SCREEN
NOTE: Each AV input can have its own picture mode
(predetermined or manual.) Current input’s selected
option is indicated by a blue marker.
CLOCK TIMER
Set the Current Time for your HDTV. You may also set
a Switch on Time to use with the On Timer Function.
When On Timer Function is set to ON, the TV will
automatically turn on at the previously set Switch on
Time.
MANUAL PICTURE SETTINGS
Choose Manual to adjust Color, Tint, Contrast,
Brightness, Sharpness, Signal Balancer, Digital Noise
Reduction and Dynamic Contrast values.
LIGHT SENSOR
Advanced Manual offers a Detailed Setting sub-menu
with the following options: Expanded DNR, White
Balance, Vertical Sharpness, Edge Enhancer, H-Size
and V-Size.
This feature detects ambient room light brightness
and uses it to control the panel brightness and picture
parameters to reduce TV power consumption.
CLOCK TIMER SCREEN
SETUP-LIGHT SENSOR SCREEN
SETUP-PANEL PROTECTION SCREEN
PICTURE SCREEN (MANUAL)
NOTE: When room lighting is dark, the panel brightness
and/or the picture setting parameters such as bright-
ness and cotrast are lowered. When room lighting is
bright, parameters are affected opposite.
Select Manual or Advanced Manual.
Cycle through the different Picture
parameters.
PANEL PROTECTION
Displaying a still picture for a long time may cause an
“afterimage” or “ghost” on the screen. To help avoid
this situation, use the Picture Rotation function.
Enter selected parameter’s adjust-
ment screen.
PARAMETER SELECTION SCREEN
If an afterimage occurs, use the White Pattern feature
immediately to repair the panel. The more severe the
afterimage, the longer the curing process may take.
The default on-time for White Pattern is 30 minutes.
Adjust the value of the selected
parameter.
Set the value of the selected para-
meter and return to parameter
selection screen.
NOTE: The sooner you remove a still picture and activate
White Pattern, the more likely it is that the panel can be
repaired.
Exit the White Pattern blank screen by pressing any
button on the remote control (except VOLUME, AUDIO
or MUTE)
NOTE: CURSOR LM keys select the next/previous
parameter without returning to the previous
menu screen.
VALUE ADJUSTMENT SCREEN EXAMPLES
Need help?
1-800-877-5032
Need help?
1-800-877-5032
14
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ON-SCREEN MENU OPERATION
SOUND
PHOTO VIEWER (USB)
View pictures on your HDTV with the use of a USB
mass storage device.
Display the On Screen menu and use the
CURSOR LM keys to select Sound.
Press ENTER.
Choose one of the four available options for your
sound settings:
USB FLASH
DRIVE
Auto – Sound setting levels are adjusted and linked
according to the current Picture option.
HDTV BACK PANEL
THUMBNAIL VIEW SCREEN
MAIN MENU SCREEN
NOTE: The HDTV switches to USB Input when a USB device
is detected.
NOTE: A thumbnail hide icon will appear if a
picture cannot be decoded or no thumb-
nail data is available.
Standard – Neutral values for sound parameters.
Manual – Set Bass and Treble levels to your preference.
Advanced Manual – Adjust the audio delay with the
Lyp-Sync Adjustment feature.
USING THE PHOTO VIEWER
Press ENTER on a thumbnail photo to enable the
Rotate, Full View and Start Slideshow functions.
Use a 4-Band Equalizer to
personalize sound settings.
Once in Full View mode:
Use the CURSOR ꢀ ꢁ keys to change picture.
Press ENTER to show the full view options menu.
MANUAL PARAMETER SCREEN
MANUAL SOUND SETTINGS
SLIDE SHOW
In the Slideshow Setup menu you may turn the Shuffle
and Quick Change options ON or OFF.
SLIDE SHOW
SETUP MENU
FULL VIEW
OPTIONS MENU
Select Manual or Advanced Manual.
Press ENTER on Start Slide-show from the Thumbnail
View Screen or from the full view options menu to
start the slideshow from the current picture.
Cycle through the different Sound
parameters.
ADVANCED MANUAL PARAMETER SCREEN
Enter selected parameter’s adjust-
ment screen.
JPEG VIEWER USB MENU
Press MENU when in Full View or Slideshow mode to
display the USB On screen menu.
Adjust the value of the selected
parameter.
Picture Setting
–
Adjust Color, Tint, Contrast,
Brightness, Sharpness and Dynamic Contrast.
NOTE: Picture Settings are separate configurations from the
settings in TV and AV inputs.
Set the value of the selected para-
meter and return to parameter
selection screen.
USB MAIN MENU SCREEN
VALUE ADJUSTMENT SCREEN EXAMPLES
Need help?
1-800-877-5032
Need help?
1-800-877-5032
16
17
Download from Www.Somanuals.com. All Manuals Search And Download.
ESTE SÍMBOLO INDICA QUÉ VOLTAJES PELIGROSOS QUE CONSTI-
TUYEN UN RIESGO DE CHOQUE ELÉCTRICO ESTÁN PRESENTES DEN-
TRO DE ESTA UNIDAD.
PRECAUCIÓN
RIESGO DE CHOQUE ELÉCTRICO ¡NO ABRIR!
ONE-YEAR LIMITED PARTS AND LABOR WARRANTY
ESTE SÍMBOLO INDICA QUE HAY INSTRUCCIONES IMPORTANTES DE
OPERACIÓN Y MANTENIMIENTO EN LA LITERATURA QUE SE ANEXA A
ESTA UNIDAD.
PRECAUCIÓN: PARA REDUCIR EL RIESGO DE CHOQUE ELÉCTRICO, NO QUITE LA CUBIERTA
(O LA TAPA TRASERA). NO HAY PARTES ADENTRO QUE LAS PUEDA REPARAR EL USUARIO.
REFIÉRASE A PERSONAL CALIFICADO PARA REPARAR EL APARATO.
THIS LIMITED PARTS AND LABOR WARRANTY IS VALID ONLY ON SANYO TELEVISIONS PURCHASED AND USED IN
THE UNITED STATES OF AMERICA, CANADA, AND PUERTO RICO, EXCLUDING ALL OTHER U.S. TERRITORIES AND
PROTECTORATES. THIS LIMITED WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL PURCHASER, AND DOES NOT
APPLY TO PRODUCTS USED FOR INDUSTRIAL OR COMMERCIAL PURPOSES.
ADVERTENCIA: PARA REDUCIR EL RIESGO DE FUEGO O CHOQUE ELÉCTRICO, NO EXPONGA ESTE
APARATO A LLUVIA O HUMEDAD.
WARRANTY APPLICATION
IMPORTANTES MEDIDAS DE SEGURIDAD
2. Guarde estas instrucciones.
3. Preste atención a los avisos.
4. Siga todas las instrucciones.
5. No use este aparato cerca del agua.
6. Limpie sólo con un trapo seco.
FOR ONE YEAR from the date of original retail purchase Sanyo Manufacturing Corporation (SMC) warrants this TV to
be free from manufacturing defects in materials and workmanship under normal use and conditions for parts and labor.
15. Si una antena externa se ha conectado al televisor,
asegúrese que el sistema de tierra de la antena esté de
forma que provea alguna protección contra fugas de
voltaje o cargas electrostáticas. En la sección 810-21 del
código eléctrico nacional de lo Estados Unidos se
menciona información con respecto a la manera adecuada
de instalar el sistema de tierra al mástil principal, aterrizaje
del cableado para la unidad de descarga de la antena,
tamaño de los conductores de tierra, localización de la
unidad de descarga de la antena, conexión a los electrodos
de tierra, y requerimientos de los electrodos de tierra.
1. Lea estas instrucciones.
For the FIRST 90 DAYS from the date of original retail purchase, Sanyo Manufacturing Corporation will replace any
defective TV via exchange at the retailer. To ensure proper warranty application, keep the original-dated-sales receipt
for evidence of purchase. Return the defective TV to the retailer along with the receipt and the included accessories,
such as the remote control. The defective TV will be exchanged for the same model, or a replacement model of equal
value, if necessary. Replacement model will be contingent on availability and at the sole discretion of Sanyo
Manufacturing Corporation.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE.
7. No obstruya las aperturas para ventilación. Instale de
acuerdo a las instrucciones del fabricante.
8. No se instale cerca de ninguna fuente de calor como
radiadores, registros de calor, estufas, u otros aparatos
(incluyendo amplificadores) que produzcan calor.
OBLIGATIONS
16. Un sistema de antena externo no debe instalarse cerca de
líneas de electricidad o circuitos de potencia o alumbrado, o
donde puedan caer sobre líneas de energía eléctrica o
circuitos cuyo contacto con ellos puede ser fatal.
For one year from the date of purchase, Sanyo Manufacturing Corporation warrants this product to be free from
defects in material and workmanship under normal use and conditions. During the first 90 days under this warranty
for any manufacturing defect or malfunction Sanyo Manufacturing Corporation will provide a new TV via exchange at
the retailer.
9. Por seguridad, no elimine la conexión de tierra de la clavi-
ja. Una clavija polarizada tiene una hoja más ancha que la
otra. Una clavija de tipo conexión a tierra, tiene dos hojas y
un tercer conector mas prolongado. La hoja ancha o el
conector prolongado están provistas para su seguridad. Si
la clavija proveída no asienta correctamente en el contacto
eléctrico, consulte a un electricista para que esa toma de AC
obsoleta sea remplazada.
17. Montaje en pared o techo—Este producto deberá de ser
montado en la pared o techo siguiendo las recomendaciones
del fabricante.
EJEMPLO DE ATERRIZAMIENTO DE ANTENA DE ACUERDO
AL CÓDIGO ELÉCTRICO NACIONAL
(National Electrical Code, ANSI/NFPA 70)
HOW TO MAKE A CLAIM UNDER THIS WARRANTY
Please call 1-800-877-5032. Please be prepared to give us the television’s model number and serial number when you
call. The model number and serial number are printed on a label attached to the back of the unit.
For customer assistance, call toll free 1-800-877-5032.
10. Proteja el cordón de potencia de que sea pisado o
perforado, particularmente en las hojas y del punto donde
éste sale del aparato.
This warranty expresses specific contractual rights; retail purchasers may have additional statutory rights which vary
from state to state.
(EFFECTIVE: March 1, 2007)
11. Sólo use anexos o accesorios especificados por el
fabricante.
Your Sanyo HDTV is registered at the time of purchase, please keep sales receipt for future reference.
12. Use únicamente con el carro, estante, tripié,
soporte o mesa especificada por el fabri-
cante, o vendida con el aparato. Cuando se
use un carro, tenga precaución cuando
mueva la combinación de carro/aparato para
evitar lesiones en caso de que se caiga.
“Nota al instalador del sistema de cable CATV :
For your protection in the event of theft or loss of this product, please fill in the information requested
below and KEEP IN A SAFE PLACE FOR YOUR OWN PERSONAL RECORDS.
Este recordatorio es dado para llamar la atención del instalador del
sistema de cable CATV al Articulo 820-40 del NEC que provee guías para
el aterrizamiento adecuado y, en particular, especifica que el conductor de
tierra del cable deberá de estar conectado al sistema de tierra del edificio,
tan cercano al punto de entrada del cable como sea práctico.”
Model No.______________________________
Date of Purchase _________________________
Purchase Price___________________________
Where Purchased_________________________
Serial No.______________________________
(Located on back of unit)
18. Este aparato no deberá de ser expuesto a ser mojado, y no
se deberán de colocar recipientes con líquido encima de él.
13. Desconecte este aparato en caso de tormenta eléctrica o
cuando no se use por un periodo de tiempo prolongado.
19. Si el conector del cable de AC se usa como artículo de
desconexión principal, entonces éste deberá de
permanecer accesible todo el tiempo.
14. Refiera todas las reparaciones a personal de servicio
calificado. Se requiere de servicio cuando el aparato se ha
dañado de cualquier forma, como si el cordón de potencia se
dañara de alguna forma, se ha derramado liquido sobre el
aparato o algún objeto le ha caído encima, el aparato se ha
expuesto a la lluvia o humedad, que no opere normalmente
o que se haya caído.
20. Una advertencia de que un aparato con construcción Clase1
debe ser conectado a la toma de corriente alterna con
protección de conexión a tierra.
Sanyo Manufacturing Corp.
3333 Sanyo Road, Forrest City, AR 72335
¿Necesita ayuda?
1-800-877-5032
Need help?
1-800-877-5032
18
19
Download from Www.Somanuals.com. All Manuals Search And Download.
INFORMACIÓN FCC
MARCAS REGISTRADAS
CONTENIDO
• Durante la instalación, se recomienda que se
maneje con cuidado por más de 2 personas.
IMPORTANTES MEDIDAS DE SEGURIDAD . . . . . . . . . .19
INFORMACIÓN FCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
MARCAS REGISTRADAS . . . . . . . . . . . . . . . . . . . . . . . . . .20
THINK GAIA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
PRECAUCIONES PANTALLA . . . . . . . . . . . . . . . . . . . . . . .20
ESPECIFICACIONES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
CONTENIDO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
PRECAUCIONES DE MANEJO . . . . . . . . . . . . . . . . . . . . . .21
QUITAR LA BASE / MONTAR EN PARED . . . . . . . . . . . . .22
Este equipo ha sido probado y se encontró en acuerdo a los
límites para un aparato digital Clase B, en acorde a la Parte 15 de
las Reglas FCC. Estos límites están diseñados para proveer
una protección razonable contra interferencia nociva en una
instalación residencial. Este equipo genera, usa y puede irradiar
energía de radio frecuencia y si no es instalado o usado de
acuerdo a las instrucciones, puede llegar a causar interferencia
nociva a radio comunicaciones. Sin embargo, no es completa-
mente seguro que no ocurrirá interferencia alguna en una
Manufacturado
bajo
licencia
de
Dolby
Laboratories. “Dolby” es una marca registrada
de Laboratorios Dolby.
• La garantía no cubre daño por manejo.
®
“Como un Asociado de ENERGY STAR
,
Sanyo Manufacturing Corporation, ha
determinado que este producto
cumple con los lineamientos en efi-
PROTEGER LA PANTALLA
PLASMA
instalación en particular. Si este equipo llegara
a
causar
®
ciencia energética de ENERGY STAR ”.
La pantalla podría dañarse si no
se le da un mantenimiento ade-
cuado. NO use objetos duros
como trapos gruesos o papel.
NO utilice presión excesiva
cuando se limpie la pantalla de
Plasma; ésto podría causar decoloración perma-
nente o puntos negros en la misma.
interferencia nociva a la recepción de radio o televisión, la cual
puede ser determinada por medio de apagar y encender el
equipo, se recomienda al usuario intentar corregir la interferencia
me-diante una o varias de las siguientes medidas:
Este símbolo impreso, significa que
el producto está listado por
Underwriters Laboratories Inc. El
diseño y manufactura de este pro-
ducto, reúne los rígidos estándares
de U.L., contra riesgos de incendio,
accidentes o descargas eléctricas.
PARA COMENZAR—
Instalación de baterías al control . . . . . . . . . . . . . . . . .22
Conexión de antena aire/cable . . . . . . . . . . . . . . . . . . .22
Operación del control remoto . . . . . . . . . . . . . . . . . . . .23
– Reorientar o mover la antena de recepción.
– Aumentar la separación entre el equipo y el receptor.
– Conectar el equipo a un enchufe en un circuito diferente al cual
esté conectado el receptor.
– Consultar al vendedor o a un técnico de radio y televisión con
experiencia para más ayuda.
CONECTORES DEL PANEL TRASERO . . . . . . . . . . . . . . . .24
CONEXIONES DE AUDIO/VIDEO . . . . . . . . . . . . . . . . . . . .25
CONEXIONES DE PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
CONFIGURACIÓN DE PC . . . . . . . . . . . . . . . . . . . . . . . . . . .26
CONEXIÓN A CORRIENTE . . . . . . . . . . . . . . . . . . . . . . . . . .27
BÚSQUEDA INICIAL DE CANALES . . . . . . . . . . . . . . . . . .27
NUNCA aplique líquidos en aerosol a la pantalla.
PRECAUCIÓN: Regulaciones de la FCC advierten que modifica-
ciones inadecuadas o cambios no autorizados a esta unidad
pueden anular la autorización del usuario para operar la unidad.
Este aparato digital de Clase B cumple con las
normas ICES-003 de Canadá.
PRECAUCIONES DE
POSICIONAMIENTO
OPERACIÓN DE MENÚ EN PANTALLA—
Establecer canales . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Búsqueda de canales . . . . . . . . . . . . . . . . . . . . . . . .28
Memoria de canales . . . . . . . . . . . . . . . . . . . . . . . . .28
Configuración . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Lenguaje del menú . . . . . . . . . . . . . . . . . . . . . . . . . .29
Subtítulos digitales . . . . . . . . . . . . . . . . . . . . . . . . . .29
V-Chip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Ahorrador de Energía . . . . . . . . . . . . . . . . . . . . . . . .31
Reloj temporizador . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Sensor de luz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Protección del panel . . . . . . . . . . . . . . . . . . . . . . . . .31
Imagen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Configuración manual de imagen . . . . . . . . . . . . . .32
Sonido . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
• Coloque la HDTV de Plasma como se indica. De
lo contrario existe la posibilidad de incendio.
Permitir el suficiente espacio en la parte de arri-
ba, lados y parte posterior del gabinete es críti-
co para una adecuada ventilación de la unidad
y permitir enfriamiento. Si la HDTV va a ser
instalada en un compartimiento, mantener
estas distancias mínimas.
RESOLUCIONES DE PC
SANYO recomienda mantener su TV en el modo
de fábrica o cambiar los ajustes del Ahorrador de
Energía de “Nivel 1” a “Nivel 2” o “Nivel 3” para
reducir el requerimiento de potencia y elevar el
ahorro de energía. Esto contribuye a la preser-
vación de nuestros recursos y del medio ambiente.
• No cubra las rejillas de ventilación de la HDTV. El
calor interno en exceso puede reducir el tiempo
de vida de su televisor y pudiera ser peligroso.
ESPECIFICACIONES
Requerimiento de Potencia: AC 120V, 60Hz
• De no utilizar su HDTV por un largo periodo de
aaConfiguración manual de sonido . . . . . . . . . . . . . .33
REPRODUCTOR DE IMÁGENES . . . . . . . . . . . . . . . . . . . . .34
GARANTÍA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
tiempo, desenchufe el cordón de potencia AC.
Consumo de Potencia: 464 watts
Peso: 38,1 kg
PRECAUCIONES DE
MANEJO
Dimensiones: ANCHO
ALTO PROFUNDO
DP50719
sin base
124.5
84.2
77.0
36.0
12.0
• Manéjese sólo por el gabinete. Nunca toque la
NOTA: Las dimensiones están en centímetros.
pantalla cuando esté manejando la HDTV.
¿Necesita ayuda?
1-800-877-5032
¿Necesita ayuda?
1-800-877-5032
20
21
Download from Www.Somanuals.com. All Manuals Search And Download.
QUITAR LA BASE Y MONTAR
EN PARED (OPCIONAL)
PARA COMENZAR
INSTALACIÓN DE BATERÍAS
OPERACIÓN DEL CONTROL REMOTO UNIVERSAL
Herramienta necesaria: Desarmador de cruz No. 3
Instale baterías en el control remoto
(2 ”AAA”, no incluídas).
NOTA IMPORTANTE:
Coloque la HDTV con el frente hacia abajo sobre
una superficie plana y acolchonada más grande
que la pantalla para protegerla junto con el acaba-
do de la HDTV. Se recomienda el manejo por más
de dos personas.
PRECAUCIONES
Para asegurarse de una buena
operación, por favor observe las
siguientes precauciones:
Una persona con experiencia debe realizar el
montaje en pared.
• Reemplace ambas baterías al
mismo tiempo. No utilice una
batería nueva con una usada.
Quite cuatro (4) tornillos del soporte me-
1tálico.PRECAUCIÓN: Sujete firmemente el
soporte al momento que quite el último tornillo.
• Existe riesgo de explosión si la batería es remplazada
con una de tipo incorrecto.
• No exponga el Control Remoto a calor o humedad.
Con cuidado, remueva el soporte de la HDTV.
• Asegúrese de que las marcas “+” y “–” de las
baterías concuerden con las del control remoto.
2
CONEXIÓN DE ANTENA PARA
SEÑALES DE AIRE O CABLE
Use los tornillos insertados en 4 de los 6 hoyos
3en la parte trasera de su HDTV Plasma para
asegurarla al estuche especial de montaje.
ANTENA
Interfase estandard universal:
ENTRADA DE ANTENA
ANÁLOGA / DIGITAL
480 200 y 480 x360.
NOTA: Este estuche no está incluído.
x
Medidas de los tornillos:
Diámetro M6, Longitud – 18mm (max.)
CABLE
Esta HDTV puede sintonizar:
• Señales aéreas digitales y análogas de una antena.
• Canales de Cable análogos o sin codificar de una
conexión directa de TV por Cable.
¿Necesita ayuda?
1-800-877-5032
¿Necesita ayuda?
1-800-877-5032
22
23
Download from Www.Somanuals.com. All Manuals Search And Download.
CONECTORES DEL PANEL TRASERO
CONEXIONES DE AUDIO / VIDEO
HDMI INPUT1, 2 y 3 se usan para conectar
aparatos digitales HD como un reproductor
Blu-ray, decodificador de Cable HD, receptor
satelital HD o consola de juegos de video.
La salida de Audio Digital es utilizada para
conectar un receptor multicanal con el uso de
un cable de audio digital.
Conexiones de Componente aceptan señales
de video SDTV, EDTV y HDTV. Utilícelas para
dispositivos digitales y obtener una muy
buena calidad de imagen.
HDMI (DVI) INPUT1 puede ser usado para
conectar un aparato DVI utilizando un adap-
tador apropiado. (Las entradas de Audio de
VIDEO3 deben estar conectadas al aparato
DVI también.)
RECEPTOR
MULTICANAL
REPRODUCTOR DVD
(o aparato similar)
RECEPTOR SATELITAL
(o aparato similar)
DVI
1 Entrada USB
Entrada de video Componente (VIDEO2 o
VIDEO3)
Entradas verde (Y), azul (Pb) y roja (Pr) de video;
5
Despliegue fotos en pantalla utilizando una
memoria USB.
Entrada de antena análoga / digital
2
3
además de las entradas de audio roja y blanca.
6
7
Salida de Audio Análogo (L/R)
Entradas HDMI (INPUT1, 2 ó 3)
Interfase completamente digital que acepta
señales de video sin compresión para obtener
la mejor calidad de imagen posible.
Entrada Audio / Video Compuesto (VIDEO1)
Entrada amarilla (video) más las entradas de audio
(roja y blanca).
NOTA: Una conexión DVI es posible por medio de la
entrada HDMI (DVI) INPUT1 utilizando un adap-
tador apropiado y conectando el audio a las
entradas de audio de VIDEO3.
8
9
Salida de Audio Digital (Coaxial)
Entrada S-Video (VIDEO1)
NOTA: La conexión de S-Video deshabilitará la conexión
en la entrada de VIDEO1 (amarillo).
Entrada para PC y estéreo audio (mini)
4
AMPLIFICADOR
ESTÉREO
MEMORIA
USB
• MONITOR RGB (D-SUB)
• AUDIO R/L (conector estéreo mini)
Óptima
alta definición
Estándar
Alta definición
Utilice la entrada USB
para conectar una
memoria USB para
desplegar imágenes
JPEG en la HDTV.
VIDEOCASETERA
(o aparato análogo)
Compuesto
La conexión Compuesta es utilizada para
conectar equipo análogo tal como una video-
casetera o un reproductor DVD que no cuente
con salidas de Componente.
La Salida de Audio Análogo (L/R) se utiliza
para conectar un amplificador estéreo
externo. (No conecte bocinas externas
directamente a la HDTV)
H D M I
S-Video
Componente
Arriba de estándar
S-Video puede ser utilizada en lugar del conec-
tor amarillo de video para una mejor imagen.
NOTA: Cables de Audio y Video no son incluídos.
NOTA: Conexiones de video Compuesto, S-Video y Componente necesitan sus conexiones de audio
roja y blanca correspondientes. Imagen en Alta Definición es posible de señales y equipo HD.
¿Necesita ayuda?
1-800-877-5032
¿Necesita ayuda?
1-800-877-5032
24
25
Download from Www.Somanuals.com. All Manuals Search And Download.
CONEXIONES Y CONFIGURACION DE PC
PARA COMENZAR— BÚSQUEDA DE CANALES INICIAL
Configuración de PC
Auto Ajuste – Ajuste automático de posición de la
imagen, dot clock y fase.
Utilice su HDTV como monitor de computadora,
conectando su televisor a su PC o Laptop por
medio de un cable de monitor apropiado.
Conecte el cable de corriente
120V AC, 60Hz
Dot Clock – Ajusta la Frecuencia de Barrido para
igualarla a la de su PC.
Antes de conectar algún cable, desenchufe de
la toma AC los cables de corriente tanto de la
HDTV como de la PC.
Fase – Ajuste la Fase cuando la imagen aparenta
vibrar o estar borrosa.
Encienda la TV
Espere las instrucciones en pantalla para
realizar la Búsqueda Inicial de Canales.
Encienda la HDTV y cualquier otro equipo
externo antes de encender la computadora.
Posición-H – Mueva la imagen horizontalmente.
PANTALLA DE CONFIGURACIÓN INICIAL
Posición-V – Mueva la imagen verticalmente.
Para evitar una condición “Fuera de Rango”,
establezca la resolución de video de su PC a una
resolución compatible con la HDTV. Ver pág. 20.
BÚSQUEDA DE CANALES
Revisa señales de Antena y Cable
conectados a la terminal ANT.
Ahorro de energía – Habilita a la HDTV entrar en
modo de espera mientras la PC no se utilice.
NOTA: Si la PC sólo cuenta con salida DVI, un conver-
tidor DVI a RGB será requerido (no incluído).
NOTA: “Auto” detecta primeramente el modo, Cable o Aire,
y luego procede con la búsqueda de canales.
SALIDA
ANÁLOGA RGB
SALIDA
DIGITAL DVI
BÚSQUEDA AV
PANEL TRASERO HDTV
Busca señales de dispositivos conecta-
dos a las entradas AV.
PANTALLA DE MÉTODO DE BÚSQUEDA
Cable estéreo
audio mini
NOTA: Encienda dispositvos externos conectados a la HDTV
antes de comenzar una Búsqueda AV.
PANTALLA DE
CONFIGURACIÓN PC
Si no se detectan señales de Antena, la HDTV
automáticamente comenzará una búsqueda AV, si
ninguna de estas dos señales son detectadas, la
HDTV sintonizará la entrada de Video1.
PC o LAPTOP
Imagen y Audio PC
Estándar – Aplica valores predeterminados a los
Cable de
monitor RGB
Sanyo recomienda utilizar
un cable de monitor con
ferrita.
parámetros de Imagen y Audio.
Manual – Ajuste los parámetros de Contraste,
Brillo y Temperatura de color de la pantalla, y los
Graves y Agudos del audio.
Pantalla Laptop
PANTALLA DE AVANCE DE BÚSQUEDA
Si utiliza su HDTV para desplegar las imágenes en
pantalla de una laptop, el mantener presionada la
tecla Fn (o FN) mientras pesiona la tecla de fun-
ción (F5, F7, F8, etc.) apropiada deberá ciclar los
modos de despliegue entre la laptop y la HDTV.
MENÚ DE PANTALLA DE AYUDA
Muestra la pantalla de problemas/solu-
ciones comunes.
Los modos pueden incluir el desplegar la imagen
sólo en la laptop, tanto en la laptop como la
HDTV, o desplegar sólo en la HDTV.
NOTA: Puede accesar el menú de Pantalla de
Ayuda más adelante por medio del
menú principal.
Sostenga
y presione
PANTALLAS DE IMAGEN Y AUDIO (MANUAL)
NOTA: Los símbolos de las teclas Fn y de función en el
teclado de la laptop pueden variar entre una
marca y otra.
NOTA: Estos parámetros no afectan los de TV normal.
¿Necesita ayuda?
1-800-877-5032
¿Necesita ayuda?
1-800-877-5032
26
27
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERACIÓN DEL MENÚ EN PANTALLA
ESTABLECER CANALES
OPERACIÓN DEL MENÚ EN PANTALLA
CONFIGURACIÓN
Despliegue el menú en pantalla. Utilice
las teclas CURSOR LM para seleccionar
Configuración. Presione ENTER.
Despliegue el menú en pantalla. Utilice
las teclas CURSOR LM para seleccionar
Establecer canales. Presione ENTER.
Utilice el menú de Configuración para establecer el
Lenguaje del menú, configurar clasificaciones V-Chip,
personalizar Subtítulos digitales, establecer el nivel
de Ahorrador de energía, establecer el Tiempo actual
y el Reloj temporizador, activar la función CEC de
Enlace HDMI, activar el Sensor de Luz y accesar la
función de Protección del panel.
BÚSQUEDA DE CANALES
Auto – Busca en el modo detectado, Cable o Aire.
PANTALLA DE MENÚ PRINCIPAL
Cable – Busca canales análogos y canales digitales de
Cable no codificados.
PANTALLA DE MENÚ PRINCIPAL
Aire (Antena) – Busca canales análogos y digitales de
transmisión aérea.
LENGUAJE DEL MENÚ
Elija entre el idioma inglés, español o francés para
desplegar el menú en pantalla.
Adición digital aérea – Busca canales digitales de
transmisión aérea, agregando canales recientemente
encontrados a la base de datos de canales.
NOTA: La función de Adición Digital Aérea no es disponible
si el modo de TV es Cable.
Presione ENTER en el idioma deseado.
Un marcador azul indica la opción
actualmente seleccionada.
PANTALLA DE ESTABLECER CANALES
PANTALLA DE CONFIGURACIÓN
LENGUAJE DE MENÚ
MEMORIA DE CANALES
Memoria de canales enlista todos los canales encontra-
dos, análogos y digitales. También muestra canales
Análogos que no se hallaron y pueden ser agregados.
SUBTÍTULOS DIGITALES
Subtítulos digitales (digital caption) es información de
texto oculta, transmitida junto con la imagen y sonido.
El encender la función hace que la HDTV abra e inter-
prete esta información (digital o análoga) y sobreim-
ponga los textos en la pantalla.
Mueve la barra de selección por todos
los canales, habilitados y deshabilitados.
NOTA: Las transmisoras locales deciden que información
transmitir.
Mueve la barra de selección sólo por
canales habilitados, saltándose los
deshabilitados.
PANTALLA DE MEMORIA DE CANALES
La letra, el fondo y el primer plano de los subtítulos
digitales pueden ser personalizados:
PANTALLA DE SUBTÍTULOS DÍGITALES
Habilita un canal deshabilitado o desha-
bilita un canal habilitado. Una palomita
indica que el canal está activado.
INFO. IMPORTANTE: Esta HDTV mantiene una sola
base de datos para canales digitales. Por lo tanto
cuando busque canales digitales de Cable, la base de
datos de canales digitales por aire será borrada.
Navegar el cursor.
Cambiar parámetro.
Usted sólo podrá recibir aquellos canales ClearQAM
(decodificados) provistos por su compañía de cable.
NOTA: Para información sobre canales digitales
Seleccionar / establecer parámetro.
¿Necesita ayuda?
1-800-877-5032
¿Necesita ayuda?
1-800-877-5032
28
29
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERACIÓN DEL MENÚ EN PANTALLA
CONFIGURACIÓN
OPERACIÓN DEL MENÚ EN PANTALLA
CONFIGURACIÓN
V – CHIP
AHORRADOR DE ENERGÍA
Utilice esta función para bloquear automáticamente
programación con contenido que crea inapropiado
para ser visto por sus hijos.
Las configuraciones de Ahorrador de Energía controlan
el brillo de las lámparas del panel para reducir el
consumo de energía. Mientras más alto el número, será
mayor la reducción de brillo y el ahorro de consumo.
NOTA: Esta función está diseñada para cumplir con
regulaciones de la FCC para V-Chip en los Estados
Unidos de América. Esta función puediera no
PANTALLA DE AHORRADOR
DE ENERGÍA
activarse con señales que originen de otros paises.
PANTALLA DE CONFIGURACIÓN V-CHIP
RELOJ TEMPORIZADOR
Configure el Tiempo actual en su HDTV. Establezca un
Tiempo de encendido para utilizar con la Función de
encendido.
Navegar el cursor.
Elegir opción.
Cuando la Función de encendido se habilita, la TV
automáticamente se encenderá a la hora establecida.
Bloquear o permitir la clasificación
seleccionada.
SENSOR DE LUZ
NOTA: Bloquear una clasificación bloqueará todas las clasifi-
caciones más altas. Desbloquear una clasificación,
desbloqueará todas las más bajas.
Esta función detecta la intensidad de luz ambiental
PANTALLA DE AJUSTAR (ESTÁNDAR)
del cuarto y controla los parámetros de brillo e
imagen para reducir el consumo de energía de la TV.
PANTALLA DE RELOJ TEMPORIZADOR
NOTA: Cuando la habitación esté oscura, el brillo del panel y/o
los parámetros de imagen tales como brillo y contraste
son reducidos. Cuando la habitación es más iluminada,
los parámetros se afectan de manera contraria.
Sistema avanzado V-Chip
Esta función es un sistema avanzado de clasificación
regional para canales digitales.
Cuando la HDTV detecta datos de la Tabla de
Clasificación Regional (RRT), se descargan y son
almacenados en memoria.
PROTECCIÓN DEL PANEL
El desplegar una imagen fija por un largo periodo de
tiempo puede causar un “fantasma” en la pantalla.
Para ayudar a reducir este efecto, use la función de
Rotación de Imagen.
La pantalla de Configuración/V-Chip es modificada
para mostrar la opción de Ajustar (avanzado).
PANTALLA DE CONFIGURACIÓN
DEL SENSOR DE LUZ
Utilice las teclas CURSOR LM y ꢀ ꢁ para seleccionar
las diferentes opciones. Use ENTER para bloquear o
desbloquear la clasificación seleccionada.
Si se presenta una imagen “fantasma” en pantalla, use
Patrón Blanco inmediatamente para reparar el panel.
Mientras más severo el problema, tardará más el
proceso de reparación. El tiempo de encendido del
Patrón Blanco es de 30 minutos.
MÁS INFORMACIÓN
Puede consultar información adicional sobre la
clasificación V-Chip y MPAA en las páginas:
NOTA: El quitar cuanto antes una imagen fija y activar Patrón
Blanco hace más probable la reparación del panel.
El presionar cualquier botón (excepto VOL LM, AUDIO
PANTALLAS DE AJUSTAR (AVANZADO)
o MUTE) cancela la pantalla blanca del Patrón Blanco.
PANTALLA DE PROTECCIÓN DEL PANEL
¿Necesita ayuda?
1-800-877-5032
¿Necesita ayuda?
1-800-877-5032
30
31
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERACIÓN DEL MENÚ EN PANTALLA
IMAGEN
OPERACIÓN DEL MENÚ EN PANTALLA
SONIDO
Despliegue el menú en pantalla. Utilice
las teclas CURSOR LM para seleccionar
Imagen. Presione ENTER.
Despliegue el menú en pantalla. Utilice
las teclas CURSOR LM para seleccionar
Sonido. Presione ENTER.
Puede elegir entre Cine, Deporte, Noticiero, Juego y
Normal, los cuales tienen valores fijos y predetermina-
dos para los diferentes parámetros. O puede elegir una
de las dos opciones Manuales para ingresar valores
personalizados.
Elija una de las cuatro opciones disponibles para su
configuración de sonido:
Auto – Utiliza valores predeterminados de acuerdo al
modo actual de Imagen.
PANTALLA DE MENÚ PRINCIPAL
PANTALLA DE MENÚ PRINCIPAL
Standard – Valores neutrales para los parámetros.
NOTA: Cada entrada de AV puede tener su propio modo de
imagen (predeterminado
seleccionada es indicada por una marca azul.
o
manual). La opción
Manual – Configure Graves y Agudos a su preferencia.
Manual Avanzado – Utilice el Ecualizador de 4 bandas
para personalizar el sonido.
CONFIGURACIÓN MANUAL DE IMAGEN
Elija Manual para ajustar Color, Tinte, Contraste, Brillo,
Nitidez, Balanceo de señal, Reducción de ruido y
Contraste Dinámico.
Manual avanzado ofrece un sub-menú de
Configuración Detallada con las sig. opciones: DNR
Expandido, Balance de Blanco, Nitidez vertical, Realce
de orillas, Tamaño-H y Tamaño-V.
PANTALLA DE IMAGEN
PANTALLA DE PARÁMETROS MANUALES
CONFIGURACIÓN MANUAL DE SONIDO
Elegir Manual o Manual avanzado.
Elegir Manual o Manual avanzado.
Seleccionar entre los diferentes
parámetros de Imagen.
Seleccionar entre los diferentes
parámetros de Imagen.
Abrir la pantalla de ajuste del pará-
metro seleccionado.
PANTALLA DE PARÁMETROS
MANUAL (AVANZADO)
Abrir pantalla de ajuste del pará-
metro seleccionado.
PANTALLA DE SELECCIÓN
DE PARÁMETROS
Ajustar el valor del parámetro
seleccionado.
Ajustar el valor del parámetro
seleccionado.
Aplicar el valor al parámetro selec-
cionado y regresar a la pantalla de
selección de parámetros.
Aplicar el valor al parámetro selec-
cionado y regresar a la pantalla de
selección de parámetros.
NOTA: Las teclas CURSOR LM seleccionan al si-
guiente o previo parámetro sin regresar a la
pantalla de menú anterior.
EJEMPLOS DE PANTALLA DE
AJUSTE DE PARÁMETROS
EJEMPLOS DE PANTALLA DE
AJUSTE DE PARÁMETROS
¿Necesita ayuda?
1-800-877-5032
¿Necesita ayuda?
1-800-877-5032
32
33
Download from Www.Somanuals.com. All Manuals Search And Download.
REPRODUCTOR DE IMÁGENES
Despliegue fotos en su HDTV con el uso de un
dispositivo de memoria USB.
GARANTÍA LIMITADA DE UN AÑO EN PARTES Y MANO DE OBRA
ESTA GARANTÍA LIMITADA DE PARTES Y MANO DE OBRA ES VÁLIDA SÓLO EN TELEVISORES SANYO COMPRADOS
Y USADOS EN LOS ESTADOS UNIDOS DE AMÉRICA, CANADÁ Y PUERTO RICO, EXCLUYENDO CUALQUIER OTRO
TERRITORIO Y PROTECTORADO DE E.E.U.U. ESTA GARANTÍA LIMITADA APLICA SÓLO A COMPRADORES
MINORISTAS Y NO APLICA A PRODUCTOS UTILIZADOS CON FINES COMERCIALES O INDUSTRIALES.
APLICACIÓN DE LA GARANTÍA
POR UN AÑO, desde la fecha de la compra original, Sanyo Manufacturing Corporation (SMC) garantiza esta televisión
de estar libre de defectos de manufactura en materiales y mano de obra bajo uso y condiciones normales para partes
y trabajo.
MEMORIA
USB
PANEL TRASERO HDTV
PANTALLA DE VISTAS EN MINIATURA
Por los PRIMEROS 90 DÍAS, desde la fecha de la compra original, Sanyo Manufacturing Corporation reemplazará
cualquier televisión defectuosa vía el vendedor original. Para asegurar la apropiada aplicación de la garantía,
conserve el recibo original de compra fechado como evidencia de compra. Regrese la TV defectuosa al vendedor
junto con su recibo de compra además de todos los accesorios incluídos, como el control remoto. La TV defectuosa
será cambiada por una del mismo modelo, o un modelo equivalente o de igual valor, si es necesario. El reemplazo
de la TV será en contingencia y disponibilidad y a la exclusiva discreción de Sanyo Manufacturing Corporation.
NOTA: La HDTV sintoniza la entrada USB cuando se detecta
una memoria en el puerto USB.
NOTA: Aparecerá un ícono “tapando” la vista en
miniatura si una foto no puede ser decodi-
ficada o no contiene datos de vista previa.
FUNCIONAMIENTO
Presione ENTER sobre una foto en vista miniatura para
abrir las funciones de Rotar, Vista completa y
Comenzar diapositivas.
ESTA GARANTÍA ES EXCLUYENTE DE Y EN LUGAR DE TODAS LAS OTRAS GARANTÍAS DE COMERCIALIZACIÓN O USO
PARA UN PROPÓSITO ESPECÍFICO.
OBLIGACIONES
Una vez en Vista completa:
Por un año, desde la fecha de la compra original, Sanyo Manufacturing Corporation (SMC) garantiza esta televisión
de estar libre de defectos de manufactura en materiales y mano de obra bajo condiciones normales de uso. Durante
los primeros 90 días bajo esta garantía para cualquier defecto de manufactura o mal funcionamiento Sanyo
Manufacturing Corporation proveerá una nueva TV vía intercambio con el vendedor.
Use las teclas CURSOR ꢀ ꢁ para cambiar de foto.
Presione ENTER para mostrar el menú de opciones.
DIAPOSITIVAS
CÓMO HACER UN RECLAMO BAJO ESTA GARANTÍA.
Por favor llame al 1-800-877-5032. Por favor esté preparado para darnos el número de modelo de la televisión cuan-
do llame. El número de modelo y el número de serie están impresos en la etiqueta agregada en la parte trasera
de la unidad.
En Configuración puede habilitar o deshabilitar las
funciones de Aleatorio y Cambio rápido.
MENÚ DE OPCIONES
EN VISTA COMPLETA
AJUSTES A
PRESENTACIÓN
Presione ENTER en Comenzar diapositivas desde la
pantalla de vistas en miniatura o elija Comenzar en el
menú de opciones para comenzar la presentación
desde la imagen seleccionada.
Para asistencia al consumidor, llame sin costo al 1-800-877-5032
Esta garantía expresa derechos contractuales específicos; minoristas podrán tener derechos estatutarios
adicionales que pueden variar de estado a estado.
(EFECTIVO: Marzo 1, 2007)
Su HDTV Sanyo es registrada al momento de la compra, por favor guarde su recibo de compra.
Para su protección en caso de robo o pérdida de este producto, por favor llene la siguiente infor-
mación requerida y GUÁRDELA en un lugar seguro para su registro personal:
MENÚ DEL REPRODUCTOR
Presione MENU al estar en vista completa o en una
presentación de diapositivas para desplegar el menú
en pantalla.
No. de Modelo__________________________
Fecha de compra ___________________________
Precio de compra ___________________________
Lugar de compra ___________________________
Ajustes de imagen – Ajuste Color, Tinte, Contraste,
Brillo, Nitidez y Contraste Dinámico.
No. de Serie ____________________________
(Localizado en la parte posterior de la TV)
NOTA: Ajustes de imagen son configuraciones separadas a
las de TV y entradas AV.
PANTALLA DE MENÚ USB
Sanyo Manufacturing Corp.
3333 Sanyo Road, Forrest City, AR 72335
¿Necesita ayuda?
1-800-877-5032
¿Necesita ayuda?
1-800-877-5032
34
35
Download from Www.Somanuals.com. All Manuals Search And Download.
|