Download from Www.Somanuals.com. All Manuals Search And Download.
To disconnect the apparatus from the mains, the plug must be pulled out from the
mains socket, therefore the mains plug shall be readily operable.
z
There is a danger of electric shock or fire.
Always unplug the unit by holding the power plug. Pulling the power cable may
damage the inside of it.
z
There is a danger of fire.
Unplug the power plug before cleaning the product.
z
There is a danger of electric shock or fire.
| Power Related | Installation Related | Cleaning and Use Related |
TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OTHER OPEN FLAMES
AWAY FROM THIS PRODUCT AT ALL TIMES.
z
There is a danger of fire.
When installing the product in a cabinet or on a shelf, make sure the front end of
the base does not protrude.
z
Dropping the product may damage it or cause injury.
Keep the power cord away from heaters.
z
The coating of the power cord may melt and cause electric shock or fire.
Do not install the product in locations exposed to oil, smoke, moisture or water
(rainwater), or in a vehicle.
z
There is a danger of electric shock or fire.
Do not install the product in locations with poor ventilation such as a bookshelf,
closet, etc.
z
An increase in the internal temperature may cause a fire.
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not install on an unstable location, or on a stand smaller than the product.
z
Make sure to keep the product out of the reach of children.
The product may fall and cause personal injury.
In case of thunder/lightning, disconnect the power cord from the wall outlet.
z
There is a danger of electric shock or fire.
Make sure the product's vents are not blocked by a table cloth or curtain.
z
An increase in the internal temperature may cause a fire.
Place the product on the ground carefully.
z
Doing so may cause damage or injury.
Do not drop the product while carrying it.
z
Doing so may cause damage or injury.
Keep the product out of children’s reach.
z
Make sure to keep the product out of the reach of children.
The product may fall and cause personal injury.
| Power Related | Installation Related | Cleaning and Use Related |
Do not insert metal items, such as chopsticks, steel wire, gimlets, or inflammable
objects such as matches or paper into the product through the ventilating openings
and the PC/Video and power terminals.
Download from Www.Somanuals.com. All Manuals Search And Download.
z
This may cause electric shock or fire.
If water or an alien substance enters the product, turn the product off,
disconnect the power cord from a wall outlet and contact a Service Center.
Do not disassemble, or attempt to fix or modify the product.
z
When the product requires repairs, contact a Service Center.
Do not use or keep the product near flammable sprays or other such substances.
z
There is a danger of fire or explosion.
Do not place containers with water, vases, drinks, chemicals, small metal parts or
heavy objects on the product.
z
If water enters the product, it may cause electric shock, or fire and when
heavy objects fall, it may cause injury.
Do not let children place objects such as toys or cookies on the product.
z
If a child tries to reach for any of these objects, the product may fall and
cause harm.
Do not look directly at the light of the lamp nor project the picture onto eyes.
z
This is dangerous especially for children.
When you remove batteries from the remote, be careful that they are not swallowed
by children. Keep batteries out of the reach of children.
z
If swallowed, see a doctor immediately.
If the product emits smoke, unusual noise, or there is a burning smell,disconnect
the power plug immediately, and contact a Service Center.
z
There is a danger of electric shock or fire.
If the power plug pin or jack is exposed to dust, water or alien substances, clean it
thoroughly.
z
There is a danger of electric shock or fire.
Download from Www.Somanuals.com. All Manuals Search And Download.
When cleaning the product, disconnect the power cord and wipe the product using
a soft dry cloth.
z
Do not use any chemicals such as wax, benzene, alcohol, thinners,
insecticide, air freshener, lubricant or detergent.
When not using the product for an extended period of time, disconnect the power
plug.
z
Otherwise, this may cause heat emission from the accumulated dirt or
degraded insulation, leading to electric shock or fire.
Do not install the product in places with heavy dust, chemical substances, high or
low temperatures, high humidity, or where it will be operated for a long period
continuously etc.
If the product is dropped or the casing is damaged, turn the product off and unplug
the power cord.
z
This may cause electric shock or fire. Contact a Service Center.
Make sure to place your remote control on a table or desk.
z
If you step on the remote control, you may fall and hurt yourself or the
product may be damaged.
Take care not to lose the lens cover of the product.
z
The lens could get damaged.
z
z
The lens cover protects the lens and should be used when the projector is
turned off.
To hide the screen while the projector is turned on, use the BLANK feature.
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment) - Europe only
(Applicable in the European Union and other European countries with separate collection
systems)
This marking shown on the product or its literature, indicates that it should not be disposed
with other household waste at the end of its working life. To prevent possible harm to the
Download from Www.Somanuals.com. All Manuals Search And Download.
environment or damage to health from uncontrolled waste disposal, please separate this
from other types of waste and recycle it responsibly to promote the sustainable reuse of
material resources.
Household users should contact either the retailer where they purchased this product, or
their local government office, for details of where and how they can take this item for
environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the
purchase contract. This product should not be mixed with other commercial wastes for
disposal.
Correct disposal of batteries in this product - alleen voor Europa
(Applicable in the European Union and other European countries with separate battery return
systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product
should not be disposed of with other household waste at the end of their working life. Where
marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury,
cadmium or lead above the reference levels in EC Directive 2006/66. If batteries are not
properly disposed of, these substances can cause harm to human health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from
other types of waste and recycle them through your local, free battery return system.
Download from Www.Somanuals.com. All Manuals Search And Download.
| Product Features | Product Views | Remote Control | Product Specifications |
Optical engine with advanced DLP technology
- 1024 x 768 panel has been adapted.
- 4 segment color wheel to implement optimal colors.
- 280 W Lamp designed to improve luminance
Vivid colors
- Quality picture tuning focused on improving color - this unit aims at realizing color coordinates that
meet broadcasting standards on video production.
Minimized fan noise and light leakage
- The airflow and fan installation structure are optimized to minimize fan noise and beam leakage.
Various Input Ports
- Connections to peripheral devices have been improved by adopting various input terminals such as
an HDMI (HDCP supported) terminal, a Component terminal, and a PC OUT terminal.
User adjustments
- This unit allows adjustment of each input port.
- The unit has a reference pattern that can be used for positioning and adjustment.
| Product Features | Product Views | Remote Control | Product Specifications |
Front/Upper Side
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Indicators
6. Zoom Knob
- STAND BY (Blue LED)
- LAMP (Blue LED)
Used to enlarge or reduce image size.
- TEMP (Red LED)
7.
POWER( ) Button
Used to turn the projector on or off.
※ Refer to the LED Indications.
2. Focus Ring
8. SOURCE Button
Used for Focus Adjustment.
Used to select input signals from the external
sources.
3. Remote Control Signal Receiver
4. Lens
9. MENU Button
Use this button to enter or exit a menu or to
move forward in a menu.
5. Adjustable Feet
You can adjust the screen position by moving the 10.
Select and Move Button(
Use this button to move to or select an item
/
)
adjustable feet up and down.
within a menu.
The buttons on the top of the projector are touch buttons.
Touch them lightly with your fingers to use them.
The label is attached to the bottom of the product.
Unpacking
Warranty Card/ Registration Card
Quick Installation Guide
User Manual CD
(Not available in all locations)
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control/ 1 Batteries
Power Cable
Cleaning Cloth
(Not available in all locations)
D-Sub Cable
Lens cover
LED Indications
●:Light is On ◐:Light is Blinking ○:Light is Off
STAND
LAMP
TEMP
Information
BY
If you press the POWER button on the remote control or projector, the screen
●
○
●
◐
○
○
○
appears within 30 seconds.
●
●
The projector is in normal operating condition.
This state appears when the projector is preparing an operation after the POWER button
on the projector or the remote control has been pressed.
The POWER button is pressed to turn off the projector, and the cooling system is in
operation to cool off the inside of the projector. (Lasts for about 1 minute and 30
seconds)
○
◐
○
Refer to Action 1 below if the cooling fan inside the projector is not in normal operation
◐
○
○
○
◐
○
◐
◐
◐
condition.
Refer to Action 2 below if the lamp cover protecting the lamp unit is not closed
properly.
Power is turned off automatically when temperature inside of the projector goes beyond
the control limit. Refer to Action 3.
●
◐
●
◐
◐
◐
◐
◐
◐
◐
◐
◐
●
○
●
A problem has occurred when operating the DDP IC in the product. Refer to Action 4.
A problem has occurred with the operation of the lamp. Refer to Action 5.
The lifetime of the lamp has expired. Refer to Action 6.
The memory in the product is not operating normally. Contact a service center.
The power for the product is not operating normally. Contact a service center.
A problem has occurred when operating the color wheel in the product. Refer to Action
◐
●
◐
4.
Clearing Indicator Problems
Classification
State
When the cooling fan
Measures
If the symptom remains even after disconnecting and then
reconnecting the power cord and turning the projector on again,
contact your product provider or our service center.
Action 1
system is not in normal
operating condition.
Download from Www.Somanuals.com. All Manuals Search And Download.
When the lamp cover
protecting the lamp unit is
not properly closed or the
sensor system is not in
normal operating
Check whether the screws at the bottom side of the projector are
fastened correctly. If they are abnormally fastened, contact your
product distributor or service center.
Action 2
condition.
Adjust the installation state of your projector by referring to the
Installation Precautions section listed above. Cool down your
projector sufficiently and then operate it again. If the same problem
occurs continually, contact your product distributor or service center.
When temperature inside
of the projector becomes
too high.
Action 3
Disconnect and reconnect the power cord and start the projector
again. If the same symptom still occurs, contact your product
distributor or service center.
When the color wheel fails to
Action 4
operate.
The lamp
malfunctions after power
turns off
Turn the power off, wait for a sufficient amount of cooling time and
then turn the power on to operate. If the same problem occurs
continually, contact your product distributor or service center.
Action 5
abnormally or after
powering on right after
turning off the projector.
Check the lamp usage time on the Information Display screen. If you
need to replace the lamp, contact your product distributor or service
center.
When the screen becomes
Action 6
darker
This Projector uses a cooling fan system to keep the unit from overheating. Operation of the cooling fan may
cause noise, which does not affect the product performance and is part of normal operation.
Rear Side
1. RS-232C port (For service input terminals)
6. HDMI/DVI IN Input port
7. PC OUT terminal
8. PC IN Input port
2. SERVICE Input port
3. VIDEO IN Input port
Download from Www.Somanuals.com. All Manuals Search And Download.
4. S-VIDEO IN Input port
9. COMPONENT IN Input port
5. Remote Control Signal Receiver
10.POWER Input port
| Product Features | Product Views | Remote Control | Product Specifications |
1.
2. AUTO Button
ON (
) Button
3.
4.
MENU (
) Button
Move (▲ ▼ ◀ ▶)/(
) Button
5. V.KEYSTONE(+/-)
(VERTICAL KEYSTONE)Button
6. VIDEO Button
7. S-VIDEO Button
8. P.SIZE Button
9. COMP Button
10.
11.
OFF (
) Button
) Button
RETURN (
12. BLANK Button
13. INFO STILL Button
14. HDMI Button
15. INSTALL Button
16. P.MODE Button
17. PC Button
1.
ON (
)
Used to turn on the projector.
2. AUTO
Adjusts the Picture automatically. (Available in PC Mode Only)
3.
4.
MENU (
)
Used to display Menu Screen.
Move (▲ ▼ ◀ ▶)/ (
)
Used to move to or select each menu item.
5. V.KEYSTONE(VERTICAL KEYSTONE) (+/-)
Use this when video scenes are distorted or tilted.
6. VIDEO
Used to switch to VIDEO Mode.
7. S-VIDEO
Used to switch to S-VIDEO Mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
8. P.SIZE
Used to adjust the size of picture screen.
9. COMP
Used to switch to COMPONENT Mode.
10.
OFF (
)
Used to turn off the projector.
11.
RETURN (
)
Returns to the previous menu.
12. BLANK
This is used to turn off the screen temporarily.
It is released when any button other than the ON/OFF button is pressed.
13. INFO STILL
INFO: Used to check source signals, picture setup, PC screen adjustment and lamp lifespan.
STILL: Used to see still images.
14. HDMI
Used to switch to HDMI Mode.
15. INSTALL
Used to flip or reverse the projected image.
16. P.MODE
Used to select Picture Mode.
17. PC
Used to switch to PC Mode.
| Product Features | Product Views | Remote Control | Product Specifications |
Design and specifications of the product may be modified without prior notice for better performance.
Specifications
Model
SP-D400S
Size
16.5 mm / 0.65 inch
XGA (1024 x 768)
Texas Instrument
280 W
Panel
Resolution
Manufacturer
Type
Lamp
Life Time
Manufacturer
2,500 Hours
Philips
Color
18.9 M (1024 x 768 x 3 x 8bit)
Optimum
1024 x 768 @ 60Hz
1280 x 1024 @75Hz
resolution
Resolution
Maximum
resolution
Input video signal
Video, S-Video, Component, Analog PC, HDMI
Input synchronization signal
Maximum Pixel Clock
Diagonal screen size
Projection Range
Separate H/V sync, TTL
136.75 MHz
40 ~250 inch
1 ~10 m
Download from Www.Somanuals.com. All Manuals Search And Download.
Power
Less than 350W
Consumption
Power
Voltage
110/220 Vac +/-10 %, 50/60 Hz +/-3 Hz
Noise
Eco : 30dB, Bright : 32dB
343.1 mm(W)x162.4 mm(H)x347.2 mm(D)
Dimensions
Weight
13.5 inches(W) x 6.4 inches(D) x 13.7 inches(H)
5.8 kg / 12,8 lb
Max 4,000 ANSI lumen
2500:1
Brightness
Contrast
Key Features
Keystone
Vertical
Temperature 32 °F ~ 104 °F (0 °C ~ 40 °C),
Operating
Humidity (10 % ~ 80 %)
User
Temperature
Environment
and Humidity
Temperature -4 °F ~ 113 °F (-20 °C ~ 45 °C) ,
Storage
Humidity (5 % ~ 95 %)
This Class B equipment is designed for home and office use. The equipment has been registered regarding
EMI for residential use. It may be used in all areas. Class A is for office use. Class A is for business while
class B emits less electromagnetic waves than class A.
The DMD Panel used in DLP Projectors consists of several hundred thousand micro mirrors. As with other
visual display elements, the DMD Panel may include a few bad pixels. Samsung and the DMD Panel
manufacturer have a rigid, bad pixel identification and limitation procedure in place and products will not
exceed the maximum number of bad pixels set by our standards. Rarely, non-displayable pixels may exist,
however it does not affect the picture quality nor the lifespan of the product.
Supported Display Modes
Horizontal Sync
Vertical Sync
Pixel
Frequency
[MHz]
Resolution
Input Source
(HxV)
Sync Type
Frequency
Frequency
polarity
polarity
[kHz]
[Hz]
31.47
37.86
37.86
31.47
35.00
37.86
37.5
P
P
N
N
N
N
N
N
N
P
P
P
P
P
N
N
N
P
P
P
N
N
P
P
P
N
N
P
70.1
85.1
85
N
N
P
N
N
N
N
N
P
N
P
P
P
P
N
N
N
P
P
P
N
P
P
P
P
P
P
P
25.18
31.5
31.5
25.175
30.24
31.5
31.5
36
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
640X350
640X400
60
66.7
72.8
75
640X480
720X400
800X600
43.27
31.47
35.16
37.88
48.08
46.87
53.67
49.73
48.36
56.4
85
70
28.322
36
56.3
60
40
72.2
75
50
49.5
56.25
57.28
65
PC
85
832X624
75
60
70
75
1024X768
60.02
68.68
67.5
75
78.75
94.5
108
85
1152X864
1152X870
1280X768
1280X960
75
68.68
47.78
60
75
100
60
79.5
108
60
63.98
79.98
55.94
70.64
33.72
60
108
1280X1024
75
135
60
106.5
136.75
74.18
1440X900
75
60
1920X1080i
Download from Www.Somanuals.com. All Manuals Search And Download.
28.125
45
P
P
P
P
P
P
P
N
N
N
N
P
P
N
P
N
P
P
P
P
P
P
P
P
P
P
P
50
60
50
60
50
70.1
85.1
85
60
75
70
60
75
60
75
60
60
60
75
60
50
60
50
60
50
60
50
P
P
P
P
P
N
N
P
N
N
P
P
P
N
P
P
P
P
P
P
P
P
P
P
P
P
P
74.25
74.25
74.25
27
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
Sep.
1280x720p
Component
37.5
720x480p
31.5
720x576p
31.25
31.47
37.86
37.86
31.47
37.5
27
25.18
31.5
31.5
25.175
31.5
28.322
40
640X350
640X400
640X480
720X400
800X600
31.47
37.88
46.87
48.36
60.02
47.78
60
49.5
65
1024X768
78.75
79.5
108
1280X768
1280X960
HDMI
63.98
79.98
33.72
28.125
45
108
1280X1024
1920x1080i
1280x720p
135
74.18
74.25
74.25
74.25
27
37.5
720x480p
720x576p
720x480i
720x576i
31.5
31.25
15.73
15.63
27
13.5
13.5
Supported Resolution/Size Modes
○ : Size & Overscan can be configured, x : Size & Overscan cannot be configured, △ : Size can be configured
Source
Picture Size
Zoom1
Input
Type
Mode
1080i
720p
576p
480p
576i
Normal
O
Zoom2
△
△
△
△
△
△
x
16:9
O
△
△
△
△
△
△
x
HD
O
O
O
O
HDMI
O
O
SD
O
O
480i
O
O
DVI
VESA
1080i
720p
576p
480p
576i
△
O
△
O
△
△
△
△
△
△
△
△
x
△
△
△
△
△
△
△
△
x
HD
O
O
O
O
Component
O
O
SD
O
O
480i
O
O
576i
△
△
△
△
△
△
△
△
△
△
△
△
△
△
△
△
VIDEO
SD
& S-VIDEO
480i
1080i
720p
576p
480p
576i
HD
x
x
x
x
x
x
SD
x
x
PC
480i
x
x
16:9
△
△
x
x
x
x
△
△
Mode
PC
4:3
Mode
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Position Modes
The position function is not supported in HDMI, Video and S-video input.
Overscan : Off
Source
Picture Size
Zoom1
Input
Type
Mode
1080i
720p
576p
480p
576i
Normal
Zoom2
16:9
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
x
O
O
O
O
O
O
x
HD
O
O
Component
O
SD
HD
SD
O
480i
O
1080i
720p
576p
480p
576i
O
x
x
O
x
x
O
x
x
O
x
x
O
PC
480i
x
x
O
16:9
O
O
x
x
x
x
O
O
Mode
PC
4:3
Mode
Overscan : On
Source
Picture Size
Input
Type
Mode
1080i
720p
576p
480p
576i
Normal
Zoom1
Zoom2
16:9
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
HD
O
O
Component
O
SD
O
480i
O
Download from Www.Somanuals.com. All Manuals Search And Download.
| Basic Settings | Connecting the Power | Connecting to video equipment |
Installing the Projector
Install the projector so that the beam from the projector is perpendicular to the screen.
Place the projector so that the lens is at the center of the screen.
If the screen is not vertically installed, the picture on the screen may not be a rectangle.
Do not install the screen in bright surroundings. If the screen is too bright, the picture on the screen will not be
displayed clearly.
When installing the screen in bright surroundings, use curtains.
You can install the projector in the following locations: Front-Floor / Front-Ceiling / Rear-Floor / Rear-Ceiling.
(To view the installation position settings)
To view the picture when installing the projector behind the screen,
Install a semi-transparent screen.
Select Menu > Setup > Install > Rear-Floor
To view the picture when installing the projector in the front of the screen,
Install the projector at the side where you are watching
the screen.
Select Menu > Setup > Install > Front-Floor
Zoom and Focus Adjustment
Zoom Knob
Focus Ring
Download from Www.Somanuals.com. All Manuals Search And Download.
You can adjust the size of image within zoom range by manipulating the
Zoom Knob.
Focus the picture on the screen using the Focus Ring.
If your product is installed at a location out of the specified projection
distance (refer to Screen Size and Projection Distance), the focus cannot
be adjusted correctly.
Leveling with Adjustable Feet
For level placing of the projector, adjust the Adjustable Feet of the projector.
You may adjust the level of the projector up to 12 mm (average 3.4°) degrees.
Depending on the position of the projector, Keystone distortion of image may appear.
Screen Size and Projection Distance
Install the projector on a flat, even surface and level the projector using the adjustable feet to realize optimal picture quality. If
images are not clear, adjust them using the Zoom Knob or Focus Ring, or move the projector forward and backward.
Horizental
(X:mm)
812.8
Vertical
(Y:mm)
609.6
Max
(Z:mm)
1730
2150
2580
3010
3430
3860
4290
4710
5140
5560
5990
6420
6840
7270
7700
8120
8550
8980
9400
9830
10260
10680
Min
(Z:mm)
1480
1840
2210
2570
2940
3300
3670
4040
4400
4770
5130
5500
5860
6230
6600
6960
7330
7690
8060
8420
8790
9160
Offset
(Y':mm)
76
Screen size
(M:inch)
40
50
1016.0
1219.2
1422.4
1625.6
1828.8
2032.0
2235.2
2438.4
2641.6
2844.8
3048.0
3251.2
3454.4
3657.6
3860.8
4064.0
4267.2
4470.4
4673.6
4876.8
5080.0
762.0
95
60
914.4
114
133
152
171
191
210
229
248
267
286
305
324
343
362
381
400
419
438
457
476
70
1066.8
1219.2
1371.6
1524.0
1676.4
1828.8
1981.2
2133.6
2286.0
2438.4
2590.8
2743.2
2895.6
3048.0
3200.4
3352.8
3505.2
3657.6
3810.0
80
90
100
110
120
130
140
150
160
170
180
190
200
210
220
230
240
250
Download from Www.Somanuals.com. All Manuals Search And Download.
This projector is designed to show images optimally on a 80 ~ 120 inch sized screen.
A. Screen
Z: Throw Distance
Y': Distance from Lens Center to Image Bottom
Setting up the PC Environment - Check the following items before connecting your PC to your projector.
1. Click the right mouse button on the Windows desktop
and click on [Properties].
<Display Properties> tab will appear.
2. Click on [Settings] tab and set the <Screen resolution> by
referring to <Resolution> described in the display mode table
supported by this projector.
You do not have to change <Color quality> setup.
3. Press the [Advanced] button.
Another property window will appear.
4. Click on [Monitor] tab and set the <Screen refresh rate> by
referring to <Vertical Frequency> described in the Supported
Resolution/Size Modes table.
Set up both the vertical and horizontal frequency instead of
<Screen refresh rate>.
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Click the [OK] button to close the window, and click the
[OK] button of the <Display Properties> window to close the
window.
The computer may restart automatically.
6. Shut down the PC and connect to the projector.
Process might vary depending on your type of computer or Windows versions.
(For example, [Properties] appears instead of [Properties (R)] as shown in 1.)
This unit appliance supports up to 24 bits per pixel in Color quality when it is used as a PC monitor.
Projected images may differ from the monitor depending on monitor manufacture or Windows versions.
When connecting the projector to a PC, check that PC setup complies to display settings supported by this
projector. If not, there may be signal problems.
| Basic Settings | Connecting the Power | Connecting to video equipment |
1. Rear of Projector
Plug the power cord into the power terminal on the rear side of the projector.
When used outside of the U.S., HAR cord with fittings of an approved agency may be used.
| Basic Settings | Connecting the Power | Connecting to video equipment |
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a DVD player/Cable/Satellite Box to HDMI/DVI
- Connecting using an HDMI/DVI cable
Connect the [HDMI/DVI IN] terminal on the back of the projector and the DVI output terminal of the DVD
player/Cable/Satellite box using a HDMI/DVI cable.
- Connecting using an HDMI cable
Connect the [HDMI/DVI IN] terminal on the back of the projector and the HDMI output terminal of the DVD
player/Cable/Satellite box using a HDMI cable.
When the connection is finished, connect the power of your projector and DVD player/Cable/Satellite box.
Using the Projector
Turn on the projector and press the [HDMI] button to select <HDMI>.
Connecting a DVD player/Cable/Satellite Box via Component
Connect the [COMPONENT IN (Y/PB/ PR)] input port at the back of the projector to the Component port at the back of
the DVD player/Cable/Satellite box with the Component cable.
When the connection is finished, connect the power of your projector and DVD player/Cable/Satellite box.
Using the Projector
Turn on the projector and press the [COMP] button to select <Component>.
Download from Www.Somanuals.com. All Manuals Search And Download.
Component Ports are marked as (Y/PB/PR), (Y, B-Y, R-Y) or (Y, Cb, Cr) depending on the manufacturer.
Connecting to VCR/Camcorder
Connect [VIDEO IN(yellow)] input port of the projector to the VIDEO (yellow) OUT port of video equipment using the
video cable.
- If the video equipment has S-VIDEO OUT port, connect it to [S-VIDEO IN] input port of the projector.
Using the S-VIDEO connection, provides a higher visual quality.
When finishing connecting the devices, connect the power of the projector and the VCR.
Using the Projector
Turn on the projector and press the [Video] button to select <Video>.
or
Press the [S-VIDEO] button to select S-Video.
Check that the projector and the video equipment are turned off before connecting cables.
This projector does not support sound. (Separate audio system is needed for sound.)
Connecting to PC
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect [PC IN] port on the rear side of the projector to the monitor output port of the PC using a PC video cable.
When connections are all completed, connect both power cords of the projector and the PC.
This product supports plug and play, therefore you do not need to install a driver on your PC.
Using the Projector
Turn on the projector and press the [PC] button to select <PC>.
If PC Mode is not available, check PC video cable is in place.
Turn on the PC and set the PC Environment when necessary.
Adjust the screen.(Auto Adjustment)
Sound comes out from PC speakers.
Connecting Video Devices (Monitor, TV, etc.)
- When using the D-sub (analog) output through another video device (monitor, TV, etc.).
Connect the PC OUT terminal of the projector and the D-sub terminal of the video device using a
D-sub cable.
After connecting them, turn on your projector and the video device (monitor, TV, etc.).
The PC OUT function only operates when the projector is connected to an external device through the [PC IN]
input terminal.
Download from Www.Somanuals.com. All Manuals Search And Download.
| Input | Picture | Setup | Option |
* Click the Play( )/Stop( ) button in the table below to view the video file.
Screen
Description
Play/Stop
Adjustment
Source List
You can select a device connected to the projector to display.
1) Component
2) S-Video
3) Video
4) PC
5) HDMI
Edit Name
You can edit the names of devices connected to the projector.
1) VCR
7) DVD Receiver
8) Game
2) DVD
3) Cable STB
4) HD STB
5) Satellite STB
6) AV Receiver
9) Camcorder
10) DVD Combo
11) PC
| Input | Picture | Setup | Option |
Download from Www.Somanuals.com. All Manuals Search And Download.
* Click the Play( )/Stop( ) button in the table below to view the video file.
Screen
Description
Play/Stop
Adjustment
Mode
Select a screen state which is customized to your projector or change the screen mode
as required.
1) Mode
- Dynamic
Select this mode for a brighter and sharper picture than Standard Mode.
-
Standard
This is the picture mode optimized to the standard broadcast signal.
- Monitor1
This is the brightest picture mode appropriate for a presentation.
- Monitor2
This is the picture mode where the brightness is optimized for text display.
Mode
- Movie
This is the picture mode optimized for watching a movie in a dark environment.
- Game
Select this when to enjoy a more vivid gaming experience.
-
Sports
Provides the optimal picture quality for sports. You can enjoy more thrilling
picture.
- User
Select this if you want to view the screen in your customized screen Mode. You
can set this in Mode-Save.
▶ The default setting is [Monitor 1].
2) Contrast : Used to adjust the contrast between the object and the background.
3) Brightness : Used to adjust brightness of the entire picture.
4) Sharpness : Used to adjust the sharpness of the picture.
Contrast
Brightness
Sharpness
Color
5) Color : Used to adjust color lighter or darker.
▶ You can only adjust Color in [S-Video] and [Video] modes.
6) Tint : Used to obtain more natural color of objects using Green or Red enhancement.
Tint
▶ You can only adjust Tint in [S-Video] and [Video] modes.
7) Color Temperature : You can change tint of the entire screen to suit your needs.
▶ This cannot be used in [Monitor1] and [Sports] modes.
- 5500K : Used to deliver optimal image quality for black-and-white films.
- 6500K : This is the color temperature that is applied for most movie productions
Color
and enables the most precise color representation.
Temperature
- 8000K : This color temperature is appropriate for very bright places and is the
defaut setting for Dynamic Picture Mode. The sharpness and brightness are
R-Gain
Download from Www.Somanuals.com. All Manuals Search And Download.
G-Gain
B-Gain
emphasized.
- 9300K : The color temperature appropriate to very bright places such as a shop.
R-Offset
G-Offset
B-Offset
1) Color Temperature
2) R-Gain
5) R-Offset
6) G-Offset
7) B-Offset
3) G-Gain
4) B-Gain
8) Gamma : An image compensation function that controls the settings according to the
video properties.
▶ This cannot be used in [Monitor1] and [Sports] modes.
- Film : The best setting for watching a film.
Gamma
- Video : The best setting for watching a TV program.
- Graphic : The Gamma mode appropriate to the PC screen and for bright video.
9) Save : Used to save custom picture settings.
Save
10) Reset : Restores the mode settings to the factory defaults.
Reset
Size
You can select a screen size according to the type of scene.
▶ Refer to "Size Support Mode".
1) Normal
2) Zoom1
3) Zoom2
4)16:9
Position
Adjust the screen position if it is not aligned.
▶ Refer to "Position Moving Support Mode".
Digital NR
When a dotted line is displayed or the screen shakes, you can view a better visual
quality picture by enabling Noise Reduction.
1) Off
2) On
Black Level
Using the Black Level function, you can set the light level of the darkest portion of the
video signal so that you can clearly see dark areas on the screen.
▶ The Black Level can only be selected in [Video], [S-Video] and [HDMI] modes.
▶ For [Video] and [S-Video] Modes
1) 0 IRE : Sets the light level of the darkest portion of the video signal to low. If the
setting does not match the input signal, the dark screen looks milky-white.
2) 7.5 IRE : Sets the light level of the darkest portion of the video signal to high. If
the setting does not match the input signal, the dark screen is saturated and may
not display properly.
▶ For [HDMI] Mode
1) Low : Set the brightness standard for dark signals to a low setting.
If the input signal is an 'HDMI-Video' type, unclear screens are displayed
normally.
2) Normal: Set the brightness standard for dark signals to a high setting.
If the input signal is an 'HDMI-PC' type, dark screens are displayed bright.
Overscan
Using this function, you can cut the edge of the picture when unnecessary information,
images appear on the edge of the picture.
▶ Refer to "Size Support Mode".
1) Off
2) On
Film Mode
Using this function, you can set the display mode optimized for playing movies.
▶ Film Mode is only supported for [Video], [S-Video] and [Component].
1) Off
2) On
PC
Eliminates or reduces noise that causes unstable screen quality, such as screen
Download from Www.Somanuals.com. All Manuals Search And Download.
shaking. If the noise is not removed using Fine Adjustment, adjust the frequency to the
maximum and then perform Fine Adjustment again.
Auto
Only activated in the PC environment.
Adjustment
1) Auto Adjustment : Used to adjust frequency and phase of PC screen
Coarse
Fine
automatically.
2) Coarse : Used to adjust frequency when vertical lines appear on PC screen.
3) Fine : Used to fine tune the PC screen.
4) Reset : Using this function, you can reset the PC menu settings to the factory
Reset
default settings.
Zoom
You can enlarge a specific part of the screen and can look at that part in detail.
1) ×1
2) ×2
3) ×4
| Input | Picture | Setup | Option |
* Click the Play( )/Stop( ) button in the table below to view the video file.
Screen
Adjustment
Description
Play/Stop
Install
To tailor the picture to the installation location, you can invert the projected images
vertically/horizontally.
1) Front-Floor : Normal Image
2) Front-Ceiling : Horizontal/Vertical Reversed Image
3) Rear-Floor : Horizontally Reversed Image
4) Rear-Ceiling : Vertically Reversed Image
Lamp Mode
Used to set the image brightness by adjusting the amount of light generated by the
lamp.
1) Eco : Using this function, you can adjust the light level of the lamp so that you
Eco
Download from Www.Somanuals.com. All Manuals Search And Download.
can comfortably watch pictures on the screen even when watching under dark
conditions. It also lowers power consumption and extends the life of the lamp.
Bright
2) Bright : Used to enhance the brightness in relatively bright ambient light. Since
this mode increases the light level of the lamp, you may experience more noise
which is produced when the projector is cooled down.
V-Keystone
If video scences are distorted or tilted, you can compensate for this using the vertical
Keystone function.
Background
When there is no signal from the broadcasting station or the external device connected
to the projector, the screen is changed to blue or black.
If a signal is received, the desktop background color disappears and a normal screen is
displayed.
1) Blue
2) Black
Test Pattern
Generated by the projector itself. Utilized as standard to optimize the installation of the
projector.
1) Crosshatch : You can check whether the picture is distorted or not.
2) Screen Size : You can refer to picture format sizes such as 1.33:1 or 1.78:1.
3) Red : Red Screen, only for color adjustment.
4) Green : Green Screen, only for color adjustment.
5) Blue : Blue Screen, only for color adjustment.
6) White : White Screen, only for color adjustment.
7) 6500K_White : White Screen, brings out the white tones for a more real white.
▶ The Red/Green/Blue colors of the test patterns are only for the color adjustment
procedures, and may not comply with the actual colors displayed during video
playback.
Factory Default
Using this function, you can reset various settings to the factory default settings.
| Input | Picture | Setup | Option |
Download from Www.Somanuals.com. All Manuals Search And Download.
* Click the Play( )/Stop( ) button in the table below to view the video file.
Screen
Description
Play/Stop
Adjustment
Language
You can select the Language used for the menu screen.
Menu Option
You can adjust the settings related to the menu screen.
1) Position : You can move the location of the menu to a new position
(up/down/right/left).
2) Transparency : Selects the transparency of the menu screen.
1) Opaque
2) Low
Position
3) Medium
4) High
Translucency
Display Time
3) Display Time : You can set the display time of the menu screen.
1) 5 sec
2) 10 sec
3) 30 sec
4) 60 sec
5) 90 sec
6) 120 sec
7) Stay On
Auto Power On
1) On: When power is supplied, the product operates automatically.
2) Off: When power is supplied, the product enters Standby mode. To operate the
product, you have to press the Power button on the remote control or key panel.
Sleep Timer
1) Off : Operates continually until you turn the power off manually.
2) 10 min/20 min/30 min : When the configured time has passed, the projector turns
to Standby mode.
▶ This function only runs when the no signal state is maintained continuously.
Information
You can check external source signals, picture setup, PC picture adjustment and lamp
use time.
Download from Www.Somanuals.com. All Manuals Search And Download.
| Before Contacting Service Personnel |
Installation and Connection
Symptoms
Troubleshooting
Check the power cable connections.
No Power.
z
z
I want to install my projector on
The ceiling installation support is sold separately. Contact your local product
the ceiling.
distributor.
External Source can not be
z
Be sure that the connection cable(s) (video) is properly connected to the
selected.
proper port. If the device is not connected properly, it can not be selected.
Menu and Remote Control
Symptoms
Troubleshooting
Remote control does not work.
z
z
Check whether your remote control is at a right angle and at the correct
distance. Remove any obstacles between your remote control and the product.
Direct lighting of 3-way light bulbs or other lighting device on the remote
sensor of the projector may affect the sensitivity and cause the remote control
to malfunction.
z
z
Check if the remote control battery is empty.
Check whether the LED indicator on the top of the projector is turned on.
I cannot select a menu.
z
Check if the menu is displayed in gray. A gray-colored menu is unavailable.
Screen and External Source
Symptoms
Troubleshooting
Cannot see picture images.
z
z
z
Be sure that the power cord of the projector is connected.
Be sure that the proper input source is selected.
Check that the connectors are properly connected to the ports at the back of
the projector.
z
z
Check the Remote Control batteries.
Be sure that the <Color>, <Brightness> settings are not at their lower limit.
Poor color.
z
Adjust the <Tint> and <Contrast>.
Images are not clear.
z
z
Adjust the focus.
Check that the projection distance is either too far or too near to the screen.
Strange noise.
z
z
z
If a strange sound continues, contact our service center.
The operating LED is lit up.
Lines appear on screen.
Refer to Corrective Actions According to LED Indications.
Because noise may occur when using your PC, adjust the frequency of the
screen.
No external device screen is displayed.
z
Check the operating status for the external device and check whether the
adjustment items, such as the Brightness and the Contrast have been changed
correctly in the <Mode> command screen of the Projector menu.
Only blue screen appears.
z
z
Be sure to properly connect the external devices. Check the connection cables
again.
Screen appears in black and white or
As mentioned above, check the adjustment items such as the Brightness,
Download from Www.Somanuals.com. All Manuals Search And Download.
odd color./ screen is too dark or
Contrast and Color in the menu.
bright.
z
If you want to restore various settings to their factory defaults, run <Factory
Default>from the menu.
Download from Www.Somanuals.com. All Manuals Search And Download.
| Care and Maintenance | Contact SAMSUNG WORLDWIDE | Other | Authority |
To clean the exterior and lens of the projector
Clean the projector using a soft dry cloth.
Do not clean the projector with flammable
substances such as benzene, thinners or a wet
cloth, as these may cause problems.
Do not touch the projector with a nail or any
other sharp objects, as this may scratch the
surface.
To clean the interior of the projector
For cleaning the interior of the projector, ask your
Service Center or a distributor.
Contact your distributor or a Service Center if
dust or other substances are inside the
projector.
Lamp Replacement
Cautions on Lamp Replacement
The projector lamp is an expendable item. For best operating performance, replace the lamp according to the
usage time. You can view the lamp usage time in the Information Display (INFO button).
Use the recommended lamp when replacing. Lamp specifications are defined in the user’s manual. Replace
with the same model provided with the projector.
- Lamp Model Name : 280W Philips fusion lamp
- Lamp Manufacture : Philips Lighting
- Lamp Life Time : 2500Hrs
- Lamp Type : 280W UHP
Check that the power cord is unplugged before replacing the lamp.
Even after the power cord has been disconnected, the lamp will be hot. Allow it to cool down for at least 1 hour
before changing the lamp.
The lamp is located at the left rear of your projector.
Before you turn the projector over to change the lamp, cover the projector with a soft cloth on a flat surface.
Do not leave the old lamp near inflammables or in reach of children. There is a danger of burn or injury.
Remove dirts or foreign materials around or inside the lamp unit using a proper vacuum device.
Download from Www.Somanuals.com. All Manuals Search And Download.
When handling the lamp, avoid touching any part of it except for the handles. If you handle the lamp
incorrectly, it may affect the screen quality and shorten its lifetime.
Contains Mercury, Dispose According to Local, State or Federal Laws
Lamp Replacement Procedure
The lamp is very hot and operates
with a high voltage. Allow it to cool
down for at least 1 hour after
disconnecting the power cord
before changing the lamp.
The lamp is located at the bottom
of the product.
Slide and open the cover in the
direction of the arrow, as shown in
the figure.
Place the product so that its
bottom looks upward and remove
the screws that hold the lamp
cover in place.
* When placing the product with
the bottom upwards, make sure to
place a soft cloth on the floor to
prevent scratches.
Remove the screws as shown in
As shown in the figure, lift up the
lamp handles by holding them and
pull the lamp.
the figure.
Assembling a new lamp is in the reverse order of the disassembly.
| Care and Maintenance | Contact SAMSUNG WORLDWIDE | Other | Authority |
If you have any questions or comments relating to Samsung products,
please contact a SAMSUNG customer care center.
NORTH AMERICA
1-800-SAMSUNG(726-7864)
1-800-SAMSUNG(726-7864)
U.S.A
CANADA
MEXICO
01-800-SAMSUNG(726-7864)
LATIN AMERICA
Download from Www.Somanuals.com. All Manuals Search And Download.
ARGENTINA
0800-333-3733
0800-124-421
4004-0000
BRAZIL
CHILE
800-SAMSUNG(726-7864)
01-8000112112
0-800-507-7267
1-800-10-7267
800-6225
COLOMBIA
COSTA RICA
ECUADOR
EL SALVADOR
GUATEMALA
HONDURAS
JAMAICA
1-800-299-0013
800-7919267
1-800-234-7267
00-1800-5077267
800-7267
NICARAGUA
PANAMA
PUERTO RICO
REP. DOMINICA
TRINIDAD & TOBAGO
VENEZUELA
1-800-682-3180
1-800-751-2676
1-800-SAMSUNG(726-7864)
0-800-100-5303
EUROPE
AUSTRIA
0810 - SAMSUNG(7267864, € 0.07/min)
BELGIUM
02-201-24-18
(French)
CZECH REPUBLIC
800 - SAMSUNG (800-726786)
DENMARK
EIRE
70 70 19 70
0818 717100
ESTONIA
FINLAND
FRANCE
800-7267
030 - 6227 515
01 48 63 00 00
GERMANY
HUNGARY
ITALIA
01805 - SAMSUNG (726-7864, € 0,14/Min)
06-80-SAMSUNG(726-7864)
800-SAMSUNG(726-7864)
8000-7267
LATVIA
LITHUANIA
LUXEMBURG
NETHERLANDS
NORWAY
8-800-77777
261 03 710
0900 - SAMSUNG (0900-7267864) ( 0,10/Min)
€
815-56 480
POLAND
0 801 1SAMSUNG(172678)
Download from Www.Somanuals.com. All Manuals Search And Download.
022 - 607 - 93 - 33
PORTUGAL
SLOVAKIA
SPAIN
80820 - SAMSUNG (726-7864)
0800-SAMSUNG(726-7864)
902 - 1 - SAMSUNG (902 172 678)
0771 726 7864 (SAMSUNG)
SWEDEN
SWITZERLAND
0848-SAMSUNG(7267864, CHF 0.08/min)
(French)
U.K
0845 SAMSUNG (7267864)
CIS
ARMENIA
0-800-05-555
AZERBAIJAN
BELARUS
088-55-55-555
810-800-500-55-500
8-800-555-555
GEORGIA
KAZAKHSTAN
KYRGYZSTAN
MOLDOVA
RUSSIA
8-10-800-500-55-500
00-800-500-55-500
00-800-500-55-500
8-800-555-55-55
8-10-800-500-55-500
TADJIKISTAN
UKRAINE
0-800-502-000
UZBEKISTAN
8-10-800-500-55-500
ASIA PACIFIC
1300 362 603
AUSTRALIA
400-810-5858
CHINA
010-6475 1880
HONG KONG
(852) 3698 - 4698
3030 8282
1800 110011
1800 3000 8282
1800 266 8282
INDIA
0800-112-8888
INDONESIA
021-5699-7777
JAPAN
0120-327-527
MALAYSIA
NEW ZEALAND
1800-88-9999
0800 SAMSUNG (0800 726 786)
Download from Www.Somanuals.com. All Manuals Search And Download.
1-800-10-SAMSUNG(726-7864)
1-800-3-SAMSUNG(726-7864)
1-800-8-SAMSUNG(726-7864)
02-5805777
PHILIPPINES
SINGAPORE
1800-SAMSUNG(726-7864)
0800-329-999
TAIWAN
1800-29-3232
THAILAND
02-689-3232
1 800 588 889
VIETNAM
MIDDLE EAST & AFRICA
8000-4726
BAHRAIN
JORDAN
800-22273
SOUTH AFRICA
TURKEY
0860-SAMSUNG(726-7864)
444 77 11
U.A.E
800-SAMSUNG(726-7864)
| Care and Maintenance | Contact SAMSUNG WORLDWIDE | Other | Authority |
Glossary
Analog Broadcast
An existing broadcasting signal transmitted by a broadcasting station in accordance with the NTSC standard.
ANTENNA IN Port
This is the port for connecting a TV antenna using a coaxial cable. It is generally used to watch public broadcast
programs.
Black Level
Black Level sets the light level of the darkest portion of the video signal to match that of the display's black level
capability so that users can clearly view dark visuals. If the setting does not match the input signal, the dark screen is
saturated and may not display properly or the dark screen looks milky-white.
Cable Broadcast
Cable Broadcast broadcasts programs via cable instead of radio waves. To view cable broadcasts, you have to
subscribe to your local cable broadcast service provider and install an additional receiver.
Color Standard
A pre-determined default color standard determined by the broadcasting standard of the corresponding country or
area.
Color Temperature
Color temperature is a simplified way to characterize the spectral properties of a light source. A low color temperature
implies a warmer (more yellow/red) light while a high color temperature implies a colder (more blue) light.
COMPOSITE IN Port
A COMPOSITE IN Port is a general video input port (yellow). Both chrominance and luminance are transmitted on the
same 75-ohm cable.
Component Port (Green, Blue, Red)
The Component Port separately transmits the luminance signal.
Digital Broadcast
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital Broadcast is a television broadcasting signal digitized and transmitted according to the United States terrestrial
digital broadcast specifications, or ATSC.
DVD (Digital Versatile Disc)
DVD is a large capacity media disk that can save multimedia content such as video, games, audio applications, etc.
using MPEG-2 video compression technology on a CD size disc.
DLP (Digital Light Processing)
DLP is a digital display technology using a DMD panel developed by TI (Texas Instruments) of the United States.
DLP HD2, DC2, DC3
This is a grade of DMD panel.
DMD (Digital Micromirror Device)
A DMD panel is an implementation of DLP technology. It consists of microscopic mirrors where each mirror represents
a pixel.
External Input
External Input is connecting video devices such as a VCR, camcorder, DTV receiver, DVD, etc. to the projector as a
video source.
Gamma Mode
Gamma Mode compensates the video signal produced for analog display devices such as a CRT (Cathode Ray Tube)
so that the video signal can be clearly displayed on a digital display device.
HDMI
▶ HDMI(High-Definition Multimedia Interface), is an interface that enables the transmission of digital audio and video
signals using a single cable.
▶ The difference between HDMI and DVI is that the HDMI device is smaller in size and has the HDCP (High Bandwidth
Digital Copy Protection) coding feature installed.
Overscan
Overscan cuts the edge of the picture when there is unnecessary information, images or noise at the edge of the
picture. For extremely poor video signals, some unnecessary video signals may be displayed on the screen.
RS-232C Port (Service Input Port)
This port is provided for service purposes. This port provides data communication in accordance with the RS-232C
communication standard.
S-Video IN Port
This is called super video. S-Video is a type of video signal which has the video brightness and color signal separated
in order to provide a better image quality.
Satellite Broadcast
Satellite Broadcast broadcasts programs via satellite so that the program can be viewed in all area in a high visual and
sound quality. Approximately 100 channels including public broadcast channels are provided. To view satellite
broadcasts, you have to install an additional receiver.
| Care and Maintenance | Contact SAMSUNG WORLDWIDE | Other | Authority |
Information in this document is subject to change without notice.
ⓒ 2009 Samsung Electronics Co., Ltd. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly
forbidden.
Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in
connection with the furnishing, performance, or use of this material.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|