HT-C5530
5.1CH Blu-ray
Home Theater System
user manual
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions
•
•
•
Ensure that the AC power supply in your house complies with the identification sticker located on the back of
your product.
Install your product horizontally, on a suitable base (furniture), with enough space around it for ventilation (3~4
inches).
Do not place the product on amplifiers or other equipment which may become hot.
Make sure the ventilation slots are not covered.
•
•
•
Do not stack anything on top of the product.
Before moving the product, ensure the Disc Insert Hole is empty.
In order to disconnect the product completely from the power supply, remove the main plug from the wall outlet,
especially when left unused for a long period of time.
•
•
•
During thunderstorms, disconnect the AC main plug from the wall outlet. Voltage peaks due to lightning could
damage the product.
Do not expose the product to direct sunlight or other heat sources. This could lead to overheating and
malfunction of the product.
Protect the product from moisture, and excess heat or equipment creating strong magnetic or electric fields (i.e.
speakers.).
•
•
•
Disconnect the power cable from the AC supply if the product malfunctions.
Your product is not intended for industrial use. Use of this product is for personal use only.
Condensation may occur if your product or disc has been stored in cold temperatures. If transporting the
product during the winter, wait approximately 2 hours until the product has reached room temperature before
using.
•
The batteries used with this product contain chemicals that are harmful to the environment.
Do not dispose of batteries in the general household trash.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
3
Safety Information
Cautions on Handling and Storing Discs
License
•
•
This product incorporates copyright protection
technology that is protected by U.S. patents and other
intellectual property rights. Use of this copyright
protection technology must be authorized by
Macrovision, and is intended for home and other
limited viewing uses only unless otherwise authorized
by Macrovision. Reverse engineering or disassembly is
prohibited.
Small scratches on the disc may reduce sound
and picture quality or cause skipping.
Be especially careful not to scratch discs when
handling them.
Holding discs
•
•
Do not touch the playback side of the disc.
Hold the disc by the edges so that fingerprints will not
get on the surface.
ABOUT DIVX VIDEO: DivX® is a digital
video format created by DivX,Inc. This is an
official DivX Certified device that plays DivX
software tools to convert your files into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified®
device must be registered in order to play DivX Video-
on-Demand (VOD) content. To generate the registration
code, locate the DivX VOD section in the device setup
menu. Go to vod.divx.com with this code to complete
the registration process and learn more about DivX
VOD.
•
Do not stick paper or tape on the
disc.
Disc Storage
•
•
•
Do not keep in direct sunlight
Keep in a cool ventilated area
Keep in a clean Protection jacket.
Store vertically.
DivX Certified to play DivX video up to HD 1080p,
including premium content.
iPod is a trademark of
Apple Inc., registered in
the U.S. and other
✎
NOTE
Do not allow the discs to become contaminated with
dirt.
•
Do not load cracked or scratched discs.
countries.
iPhone is a trademark of Apple Inc.
Handling and Storing Discs
If you get fingerprints or dirt on the disc, clean it with a
mild detergent diluted in water and wipe with a soft cloth.
•
•
Manufactured under license from Dolby Laboratories.
Dolby, Pro Logic and the double-D symbol are
trademarks of Dolby Laboratories.
< Open Source License Notice >
In the case of using open source software, Open Source
Licenses are available on the product menu.
•
When cleaning, wipe gently from the inside to
the outside of the disc
✎
NOTE
Condensation may form if warm air comes into
contact with cold parts inside the product. When
condensation forms inside the product, it may not
operate correctly. If this occurs, remove the disc
and let the product stand for 1 or 2 hours with the
power on.
Copyright
© 2010 Samsung Electronics Co., Ltd. All rights
reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
English
Contents
2
3
4
4
4
Safety Warnings
SAFETY INFORMATION
Precautions
Cautions on Handling and Storing Discs
License
Copyright
2
7
8
9
Key features of your new Blu-ray Home Theater
Icons that will be used in manual
Disc Types and Characteristics
GETTING STARTED
13 Accessories
14 Description
7
14
15
Front Panel
Rear Panel
16 Remote control
18 Connecting the Speakers
CONNECTIONS
20 Connecting the Optional Wireless Receiver Module
22 Connecting the Video Out to your TV
24
Connecting Audio from External Components
25 Connecting to the Network
26 Connecting the FM Antenna
18
27 Before Starting (Initial Setting)
28 Setting the Menu
29 Display
SETUP
29
29
29
31
31
31
31
31
TV Aspect
BD Wise (Samsung Products only)
Resolution
27
HDMI Format
Movie Frame (24 Fs)
Progressive Mode
Still Mode
HDMI Deep Color
32 Audio
32
33
33
33
34
35
35
Speaker Setting
Musical Room Calibration
EQ Optimizer
HDMI Audio
Digital Output
Dynamic Range Control
AV Sync
35 System
35
35
35
35
36
36
36
Initial Setting
Internet@TV Screen Size
Anynet+(HDMI-CEC)
BD Data Management
Clock
DivX(R) Registration
DivX(R) Deactivation
37 Network Setup
37
40
40
Network Settings
Network Status
BD-LIVE Internet Connection
40 Language
41 Security
41
41
Parental Rating
Change Password
Download from Www.Somanuals.com. All Manuals Search And Download.
English
5
Contents
41 General
SETUP
41
41
41
41
Background
Energy Saving
Front Display
Power On/Off Sound
42 Support
41
42
42
Software Upgrade
Contact Samsung
43 Playing a Disc
BASIC FUNCTIONS
43 Using the Disc menu / Title menu / Popup menu
44 Using the Search and Skip Functions
45 Slow Motion Play/Step Motion Play
45 Repeat Playback
43
46 Using the TOOLS button
48 Listening to Music
50 Sound Mode
51 Playing back a Picture
52 Playing back a USB Storage
52 Listening to Radio
53 Using an iPod
55 Using Internet@TV
59 BD-LIVE™
NETWORK SERVICES
59 Software Upgrade Notification
59 Using the AllShare Function
55
61 Troubleshooting
64 Index
65 Specifications
OTHER INFORMATION
61
•
Figures and illustrations in this User Manual are provided for reference only and may differ from actual product appearance.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
English
Getting Started
Key features of your new Blu-ray Home Theater
Product Features
Playback of many disc types, plus an FM tuner
This product allows you to play various discs, including BD-ROM/RE/R, DVD-VIDEO, DVD-RW/-R
(V mode), DVD+RW/+R, MP3/WMA, JPEG, DivX/MKV/MP4, and CD-R/RW, with a sophisticated
FM tuner, all in a single player.
Full HD audio decoding support (Dolby Digital, Dolby Pro Logic II, Dolby Digital Plus,
Dolby TrueHD, DTS, DTS-HD HRA, DTS-HD MA Essential)
HDMI
HDMI transmits Blu-Ray/DVD video and audio signals simultaneously, and provides a clearer picture.
The 1080p(Full HD) resolution provides even clearer pictures.
AV SYNC function
Video may lag behind the audio if the product is connected to a digital TV.
To compensate for this, you can adjust the audio delay time to sync up with the video.
iPod & iPhone support
You can enjoy music files by connecting your iPod to the product with the supplied iPod dock.
BD Wise
BD Wise automatically adjusts BD Wise-compliant Samsung products to the optimal settings between
them. This feature is enabled only if BD Wise-compliant Samsung products are connected to each other
using an HDMI cable.
Internet@TV
You can download various chargeable or free-of charge applications through network connection.
Blu-ray Disc Features
Blu-ray Discs support the highest quality HD video available in the industry - Large capacity means no
compromise on video quality. Furthermore, a Blu-ray Disc has the same familiar size and look as a DVD.
* The following Blu-ray Disc features are disc dependant and will vary. Appearance and navigation of
features will also vary from disc to disc. Not all discs will have the features described below.
Video highlights
The BD-ROM format for movie distribution supports three highly advanced video codecs, including AVC,
VC-1, and MPEG-2.
HD video resolutions are also available:
1920 x 1080 HD
1280 x 720 HD
For high-definition playback
To view high-definition contents on a Blu-ray disc, an HDTV (High Definition Television) is required.
Some discs may require using the product's HDMI OUT to view high-definition content. The ability to view
high-definition content on Blu-ray disc may be limited depending on the resolution of your TV.
BD-LIVE
You can use a Blu-ray Disc supporting BD-LIVE through network connection to enjoy various contents
provided by the disc manufacturer.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
7
Getting Started
Icons that will be used in manual
Make sure to check the following terms before reading the user manual.
Term
Logo
Icon
Definition
BD-ROM
This involves a function available on a BD-ROM.
h
z
Z
This involves a function available on a BD-RE/-R disc recorded in the
BD-RE format.
BD-RE/-R
DVD-VIDEO
This involves a function available on a DVD-VIDEO.
DVD-RW(V)
DVD-R
This involves a function available on recorded DVD+RW or DVD-RW(V)/
DVD-R/+R discs that have been recorded and finalized.
DVD+RW
y
DVD+R
Audio CD
This involves a function available on an audio CD-RW/-R (CD-DA format).
o
w
G
This involves a function available in a CD-RW/-R, DVD-RW/-R disc or a
USB storage media containing MP3 or WMA contents.
MP3
WMA
-
-
This involves a function available in a CD-RW/-R, DVD-RW/-R disc or a
USB storage media containing JPEG contents.
JPEG
DivX
MKV
MP4
This involves a function available in a CD-RW/-R, DVD-RW/-R disc or a
USB storage media containing DivX contents.
x
DivX
-
USB storage
device
This involves a function available on a USB storage device.
F
!
This involves a situation where a function does not operate or settings may
be cancelled.
CAUTION
NOTE
-
-
-
This involves tips or instructions on the page that help each function
operate.
✎
This function provides direct and easy access pressing the button on
the remote control.
Shortcut Key
•
•
This product is compatible with the NTSC color system only.
PAL discs will not play.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
English
Logos of Discs that can be played
Disc Types and Characteristics
Blu-ray Disc Compatibility
Blu-ray is a new and evolving format. Accordingly, disc
compatibility issues are possible. Not all discs are
compatible and not every disc will play back. For
additional information, refer to the Disc Types and
Characteristics section of this Manual. If you encounter
compatibility problems, please contact the SAMSUNG
customer care center at 1-800 SAMSUNG.
Blu-ray Disc
Dolby Digital Plus
Dolby TrueHD
✎NOTE
NTSC broadcast system in
U.S.A, Canada, Korea,
Japan
Playback may not work for some types of discs, or
when specific operations, such as angle change
and aspect ratio adjustment, are being performed.
Information about the discs is written in detail on
the box. Please refer to this if necessary.
Do not allow the disc to become dirty or scratched.
Fingerprints, dirt, dust, scratches or deposits of
cigarette smoke on the recording surface may
make it impossible to use the disc for playback.
When a BD-Java title is played, loading may take
longer than a normal title, or some functions may
perform slowly.
DTS-HD High Resolution
Audio
Java
Discs that cannot be played
•
•
•
•
•
•
HD DVD Disc
DVD-RAM
DTS-HD Master Audio |
Essential
3.9 GB DVD-R Disc for Authoring.
DVD-RW(VR mode)
BD-LIVE
Super Audio CD(except CD layer)
DVD-ROM/PD/MV-Disc, etc CVD/CD-ROM/
CDV/CD-G/CD-I/LD
•
CDGs play audio only, not graphics.
✎NOTE
Some commercial discs and DVD discs purchased
outside your region may not be playable with this
product. When these discs are played, either “No
disc.” or “Please check the regional code of the
disc.” will be displayed.
If a DVD-R/-RW disc has not been recorded properly
in DVD video format, it will not be playable.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
9
Getting Started
Region code
Disc Types
BD-ROM
Both the product and the discs are coded by
region. These regional codes must match in
order to play the disc. If the codes do not match,
the disc will not play.
Blu-ray Disc Read Only Memory. A BD-ROM disc
contains pre-recorded data. Although a BD-ROM
may contain any form of data, most BD-ROM discs
will contain movies in High Definition format, for
playback on the product. This product can play
back pre-recorded commercial BD-ROM discs.
Region
Disc Type
Blu-ray
Area
Code
North America, Central America,
South America, Korea, Japan,
Taiwan, Hong Kong and South
BD-RE/BD-R
A
Blu-ray Disc Rewritable/Blu-ray Disc Recordable.
BD-RE/BD-R is the ideal format for making
backups, or recording personal video.
East Asia.
Europe, Greenland, French
territories, Middle East, Africa,
Australia and New Zealand.
DVD-VIDEO
B
•
A digital versatile disc (DVD) can contain up to 135-
minutes of images, 8 audio languages and 32 subtitle
languages. It is equipped with MPEG-2 picture
compression and Dolby Digital surround, allowing you
to enjoy vivid and clear quality images.
India, China, Russia, Central and
South Asia.
C
1
2
3
The U.S., U.S. territories and
Canada
•
•
When switching from the first layer to the second
layer of a dual-layered DVD Video disc, there may
be momentary distortion in the image and sound.
This is not a malfunction of the product.
Once a DVD-RW/-R recorded in Video Mode is
finalized, it becomes DVD-Video. Pre-recorded
(pre-stamped) commercial DVDs with movies are
also referred to as DVD-Videos. This product can
play back pre-recorded commercial DVD discs
(DVD-Video discs) with movies.
Europe, Japan, the Middle East,
Egypt, South Africa, Greenland
Taiwan, Korea, the Philippines,
Indonesia, Hong Kong
DVD-VIDEO
Mexico, South America, Central
America, Australia, New Zealand,
Pacific Islands, Caribbean
4
DVD-R/-RW
•
Once a DVD-R/-RW recorded in Video Mode is
finalized, it becomes DVD-Video. Ability to play
back may depend on recording conditions.
Russia, Eastern Europe, India,
most of Africa, North Korea,
Mongolia
5
6
•
•
This product can play back DVD-R disc recorded
and finalized with a Samsung DVD video recorder.
Playback can be perfomed with DVD-RW discs in
the Video Mode and finalized only.
China
DVD+RW
•
This product can play back a DVD+RW disc
recorded with a DVD Video recorder. Ability to
play back may depend on recording conditions.
DVD+R
•
This product can play back a DVD+R disc recorded
and finalized with a DVD Video recorder. Ability to
play back may depend on recording conditions.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
10
Audio CD
DivX(Digital video express)
•
•
•
An audio disc on which 44.1kHz PCM Audio is
recorded.
DivX is a video file format developed by Microsoft and is
based on MPEG4 compression technology to provide
audio and video data over the Internet in real-time.
MPEG4 is used for video encoding and MP3 for audio
encoding so that the users can watch a movie at near
DVD-quality video and audio.
This product can play back CD-DA format audio
CD-R and CD-RW discs.
The product may not be able to play some CD-R or
CD-RW discs due to the condition of the recording.
Supported Formats(DivX)
CD-R/-RW
This product only supports the following media formats.
If both video and audio formats are not supported, the
user may experience problems such as broken images
or no sound.
•
Use a 700MB(80 minutes) CD-R/-RW disc.
If possible, do not use a 800MB(90 minutes) or above
disc, as the disc may not play back.
If the CD-R/-RW disc was not recorded as a closed
session, you may experience delays when playing
back the beginning of the disc or all recorded files
may not play.
Some CD-R/-RW discs may not be playable with this
product, depending on the device which was used to
burn them. For contents recorded on CD-R/-RW
media from CDs for your personal use, playability
may vary depending on contents and discs.
•
Supported Video Formats
Format
Supported Versions
•
AVI
DivX3.11~DivX5.1, XviD
Supported Audio Formats
Sampling
Frequency
Format
Bit Rate
Disc Format
MP3
AC3
DTS
80~384kbps
128~384kbps
1.5Mbps
44.1khz
Using MP3 disc
44.1/48khz
44.1khz
•
CD-R/-RW, DVD-RW/-R recorded with UDF,
ISO9660 or JOLIET format can be played back.
•
Only MP3 files with the “.mp3” or “.MP3” extension
•
•
DivX files, including audio and video files, created
in the DTS format can only support up to 6Mbps.
Aspect Ratio : Although the default DivX resolution
is 640x480 pixels (4:3), this product supports up
to 800x600 pixels (16:9). TV screen resolutions
higher than 800 will not be supported.
can be played.
•
•
•
Playable bit rate range is from 56 Kbps to 320 Kbps.
Playable sample-rate is 32KHz to 48KHz.
The product can handle a maximum of 1500 files and
folders under a parent folder. For MP3 files recorded with
a VBR(Variable Bit Rates), the sound may cut in and out.
•
•
When you play a disc whose sampling frequency is
higher than 48khz or 320kbps, you may experience
shaking on the screen during playback.
Using JPEG disc
•
•
•
CD-R/-RW, DVD-RW/-R recorded with UDF,
ISO9660 or JOLIET format can be played back.
Qpel and gmc is not supported.
Only JPEG files with the ".jpg", ".JPG", ".jpeg" or
MKV, MP4
"JPEG" extension can be displayed.
Progressive JPEG is supported.
•
•
CD-R/-RW, DVD-R/-RW, USB, PC streaming
Video Files with the following extensions can be
played. : .avi, .divx, .mkv, .mp4, .AVI, .DIVX,
.MKV, .MP4
DVD-RW/-R (V)
•
This is a format that is used for recording data on a
DVD-RW or DVD-R disc. The disc can be played by
this product once it has been finalized.
If a disc that has been recorded in Video Mode by a
different maker’s recorder but has not been finalized,
it cannot be played by this product.
✎
NOTE
•
Some DivX, MKV and MP4 format discs may
not play, depending on the video resolution and
frame rate condition.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
11
Getting Started
Supported File Formats
Video File Support
File Extension
Container
Video Codec
Divx 3.11/4.x/5.1/6.0
XviD
Audio Codec
Resolution
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
MP3
AC3
DTS
WMA
PCM
*.avi
AVI
MP4v3
H.264 BP/MP/HP
VC-1 AP(wmv1)
DivX 5.1/6.0
XviD
MP3
AC3
DTS
*.mkv
MKV
H.264 BP/MP/HP
VC-1 AP
*.wmv
*.mp4
WMA
AAC
WMV
MP4
VC-1 SM
MP4 (mp4v)
H.264 BP/MP/HP
MPEG1
MP1, 2
AC3
DTS
*.mpg
*.mpeg
PS
MPEG2
H.264 BP/MP/HP
Music File Support
File Extension
Container
Audio Codec
Support Range
*.mp3
MP3
-
MP3
Compliant with WMA version 10
* Sampling rates (in kHz) - 8, 11, 16, 22, 32,
44.1, 48
*.wma
WMA
WMA
* Bit rates - All bit-rates in the range 5kbps to
384kbps
Download from Www.Somanuals.com. All Manuals Search And Download.
English
12
•
•
CBI (Control/Bulk/Interrupt) is not supported.
USB Host Specification
Digital Cameras that use PTP protocol or
require additional program installation when
connected to a PC are not supported.
A device using the NTFS file system is not
supported. (Only the FAT 16/32 (File Allocation
Table 16/32) file system is supported.)
USB Host Specification
•
Supports USB 1.1 or USB 2.0 compliant devices.
•
•
• Supports devices connected using the USB
A type cable.
• Supports UMS (USB Mass Storage Device)
V1.0 compliant devices.
• Supports FAT(FAT, FAT16, FAT32) file
system formatting.
Does not operate with Janus enabled MTP
(Media Transfer Protocol) devices.
USB Devices that can be used with the
product
Non-compliance
•
Does not support a device that requires installing
a separate driver on the PC (Windows).
1. USB Storage Device
2. MP3 Player
3. Digital Camera
• Does not support connection to a USB hub.
• A USB device that is connected using an
USB extension cable may not be recognized.
4. Removable HDD
Operational Limitations
•
•
Removable HDDs equipped with less than 160
Gbytes are supported. Removable HDDs
equipped with 160Gbytes or more may not be
recognized, depending on the device.
If the connected device does not work due to
insufficient power supply, you can use a
separate power cable to supply power so that it
can work properly. The USB cable connector
may differ, depending on the manufacturer of
the USB device.
• If the connected device has multiple drives
(or partitions) installed, only one drive
(or partition) can be connected.
• A device supporting USB 1.1 alone may
cause a difference in the picture quality,
depending on the device.
Supported file Formats
5. USB card Reader: One slot USB card reader and
Format
Still Picture
Music
Multi-slot USB card reader.
File name
File extension
Bit rate
Version
Pixel
Sampling Frequency
JPG
MP3
•
The USB card reader may not be supported,
depending on the manufacturer.
JPG .JPEG
.MP3
–
80~384kbps
•
If you install multiple memory devices into a
multi-card reader, you may experience
problems.
–
640x480
–
–
–
44.1kHz
Accessories
Check for the supplied accessories below.
FUNCTION
POWER
T
V
S
O
U
R
C
E
B
D
R
E
C
E
I
V
E
R
/
T
V
SLEEP
1
4
2
5
8
0
3
6
9
7
F
U
L
L
S
C
R
E
E
N
REPEAT
MUTE
TUNING
/CH
VOL
DISC MENU
TOOLS
SFE MODE
MENU
TITLE MENU
POPUP
INFO
RETURN
A
EXIT
T
UNER
M
E
MORY
MO/ST
B
C
D
INTERNET
@
DSP
Remote Control/
Batteries (AAA size)
Video Cable
FM Antenna
iPod Dock
User's Manual
ASC Microphone
Download from Www.Somanuals.com. All Manuals Search And Download.
English
13
Getting Started
Description
Front Panel
2
3
4
5
6
7
8
9
10
11
12
13
1
ASC IN
Turns the product on and off.
Insert disc here.
1
2
3
4
5
POWER BUTTON (
DISC TRAY
)
REMOTE CONTROL SENSOR
DISPLAY
Detects signals from the remote control.
Displays the playing status, time, etc.
Opens and closes the disc tray.
OPEN/CLOSE BUTTON
The mode switches as follows :
BD/DVD ꢀ D. IN ꢀ AUX ꢀ FM
Goes back to the previous title/chapter/track.
Tunes down the FM frequency band.
FUNCTION BUTTON
6
7
TUNING DOWN & SKIP BUTTON
STOP BUTTON
Stops disc playback.
8
9
PLAY/PAUSE BUTTON
Plays a disc or pauses playback.
Goes to the next title/chapter/track.
Tunes up the FM frequency band.
TUNING UP & SKIP BUTTON
VOLUME CONTROL
USB PORT
10
11
12
13
Volume adjustment.
A USB storage device can be connected here and used as storage when connected to BD-
LIVE. It can also be used for software upgrades and MP3/JPEG/DivX/MKV/MP4 playback.
ASC IN JACK
Used to connect the ASC Microphone for setting up MRC (Musical Room Calibration).
✎NOTE
Software upgrades using the USB Port must be performed with a USB memory flash stick only.
A USB device consuming more than 500mA requires a separate power supply device for normal operation.
A USB HDD device cannot be used for BD Data storage (BD-LIVE).
Download from Www.Somanuals.com. All Manuals Search And Download.
English
14
Rear Panel
1
2
3
4
5
6
7
8
9
10
11
12
FM ANT
LAN
COMPONENT OUT
DIDITAL
AUDIO IN
WIRELESS
H
D
MI OUT
OPTICAL
iPod
SPEAKER IMPEDANCE
:
3
WIRELESS LAN
AUX IN
VIDEO OUT
5.1 CHANNEL SPEAKER OUTPUT
CONNECTORS
Connect the front, center, surround, subwoofer speakers.
1
The cooling fan supplies cool air to the product to prevent overheating
and always revolves when the power is on.
COOLING FAN
iPod JACK
2
3
4
5
Connect the iPod dock connector here.
Connect the FM antenna.
FM 75 COAXIAL JACK
—
The TX card enables communication between the product and the
optional wireless receiver module.
TX CARD CONNECTION (WIRELESS)
EXTERNAL DIGITAL OPTICAL IN JACKS
(OPTICAL)
Use this to connect external equipment capable of digital output.
6
Use an HDMI cable, connect this HDMI output terminal to the HDMI
input terminal on your TV for the best quality picture.
HDMI OUT JACK
7
8
Can be used for network based services (see pages 55~60),
BD-LIVE and software upgrade with a wireless LAN adapter.
WIRELESS LAN JACK
LAN TERMINAL
Can be used for network based services (see pages 55~60),
BD-LIVE and software upgrade under the network connection.
9
Connect to the 2CH analog output of an external device
(such as a VCR)
AUX IN JACKS
10
11
12
COMPONENT VIDEO OUT JACKS
VIDEO OUT JACK
Connect a TV with Component video inputs to these jacks.
Connect your TV's Video Input jack (VIDEO IN) to the VIDEO OUT
Jack on this product.
! CAUTION
Ensure a minimum of 4 inches of clear space on all sides of the cooling fan when installing the product.
Do not obstruct the cooling fan or ventilation holes.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
15
Getting Started
Remote control
Tour of the Remote Control
FUNCTION
This is mode selection button.
or
POWER
TV SOURCE
Press to select TV's video mode.
Turn the product on and off.
Set a Sleep time to shut off the
procuct.
BD RECEIVER/TV
SLEEP
Press to select BD RECEIVER/TV
mode.
To open and close the disc tray.
1
4
2
5
8
0
3
6
Press numeric buttons to operate options.
7
9
FULL SCREEN
REPEAT
Allows you to repeat a title, chapter,
track or disc.
Press this to see the full screen on a TV.
Press to skip backwards or forwards.
Press to search backwards or
forwards.
Press to pause a disc.
Press to stop/play a disc.
Cut off the sound temporarily.
MUTE
Adjust the volume.
Search for active FM stations and
change channels.
TUNING
/CH
VOL
DISC MENU
TOOLS
SFE MODE
MENU
You can set the SFE(Sound Field
Effect) mode best suited for the
type of music you are listening to.
Use this to enter the popup
menu/title menu.
Press this to move to the home
menu.
TITLE MENU
POPUP
Press to view the disc menu.
INFO
Use this to display the playback
information when playing
a Blu-ray/DVD disc.
Press this to use the Tools menu.
Select on-screen menu items and
change menu value.
Press this to exit the menu.
RETURN
A
EXIT
Return to the previous menu.
Used to set a preset radio
frequency.
TUNER
MEMORY
MO/ST
These buttons are used both for menus
on the product and also several
Blu-ray Disc functions.
B
C
D
Select MONO or STEREO for radio
broadcasting.
@
INTERNET
DSP
Press this to link to various
Internet@TV services.
Regulate and stabilize the volume
level. (Digital Signal Processor)
Select the desired Dolby Pro
Logic II audio mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
16
Installing batteries in the Remote Control TV Brand Code List
* Battery size: AAA
Brand
Code
56, 57, 58
01, 15
01, 02, 03, 04, 05,
06, 07, 08, 09, 10,
11, 12, 13, 14
Brand
Code
Admiral
Mitsubishi/
18, 40, 59, 60, 75
(M.Wards)
MGA
A Mark
Anam
AOC
MTC
NEC
18
18, 19, 20, 40, 59, 60
Nikei
03
03
03
Onking
Onwa
01, 18, 40, 48
Bell &
Howell
06, 07, 08, 09, 54,
66, 67, 73, 74
Panasonic
Penney
Philco
57, 58, 81
(M.Wards)
18
Brocsonic
Candle
59, 60
18
03
03, 18, 25
97
03
18
✎NOTE
03, 15, 17, 18, 48,
54, 59, 62, 69, 90
Make sure to match the “+” and “–” ends of
Cetronic
Citizen
15, 17, 18, 40,
48, 54, 62, 72
63, 66, 80, 91
15, 18, 59
40
06, 66, 67
17, 48, 56, 60,
61, 75
Philips
the batteries with the diagram inside the
compartment.
Pioneer
Portland
Proton
Cinema
Classic
Concerto
Contec
Coronado
Craig
Assuming typical TV usage, the batteries last
for about one year.
The remote control can be used up to
approximately 23 feet (7 meters) in a straight line.
Quasar
46
15
Radio
Shack
03, 05, 61, 82, 83, 84
RCA/
Proscan
18, 59, 67, 76, 77,
78, 92, 93, 94
Croslex
Crown
62
03
Setting the Remote Control
Realistic
Sampo
03, 19
40
Curtis
Mates
59, 61, 63
03
02, 03, 04, 15, 16,
17, 18, 19, 20, 21,
22, 23, 24, 25, 26,
27, 28, 29, 30, 32,
34, 35, 36, 48, 59, 90
You can control certain functions of your TV with
this remote control.
00, 15, 16, 17, 40,
43, 46, 47, 48, 49,
59, 60, 98
CXC
Samsung
Sanyo
Scott
Sears
Sharp
19, 61, 65
03, 40, 60, 61
15, 18, 19
Daewoo
When operating a TV with the remote control
Daytron
Dynasty
40
03
1. Press the BD RECEIVER/TV button to set the
15, 57, 64
remote control to TV mode.
Signature
2000
03, 15, 40, 46, 59, 61,
57, 58
Emerson
64, 82, 83, 84, 85
(M.Wards)
2. Press the POWER button to turn on the TV.
Fisher
Funai
19, 65
03
03
Sony
Soundesign
Spectricon
SSS
50, 51, 52, 53, 55
3. While holding down the POWER button, enter
03, 40
01
18
the code corresponding to your brand of TV.
Futuretech
General
06, 40, 56, 59,
66, 67, 68
40
15, 18, 50, 59, 69
45
56, 59, 67, 86
70
59, 61, 87, 88
03, 15, 40
15
•
If there is more than one code listed for
your TV in the table, enter one at a time to
determine which code works.
Electric (GE)
18, 40, 48, 54,
59, 60, 62
Hall Mark
Hitachi
Inkel
Sylvania
Symphonic
Tatung
Techwood
Teknika
TMK
61, 95, 96
06
18
03, 15, 18, 25
18, 40
19, 57, 63, 71
18
•
Example : For a Samsung TV
JC Penny
JVC
While holding down the POWER button, use the
number buttons to enter 00, 15, 16, 17 and 40.
KTV
4. If the TV turns off, the setting is complete.
KEC
Toshiba
Vidtech
Videch
•
You can use the TV POWER, VOLUME,
CHANNEL, and Numeric buttons (0~9).
KMC
LG
01, 15, 16, 17, 37, 38,
59, 60, 69
(Goldstar)
39, 40, 41, 42, 43, 44
15, 17, 18, 40,
48, 54, 60, 64
Luxman
18
Wards
✎NOTE
LXI
(Sears)
19, 54, 56, 59,
The remote control may not work on some
Yamaha
York
18
40
03
58, 79
01
03, 54
60, 62, 63, 65, 71
brands of TV's. Also, some operations may not
be possible, depending on your brand of TV.
The remote control will work with Samsung TVs
by default.
15, 17, 18, 48, 54,
Magnavox
59, 60, 62, 72, 89
Yupiteru
Zenith
Marantz
Matsui
MGA
40, 54
54
18, 40
Zonda
Dongyang
Download from Www.Somanuals.com. All Manuals Search And Download.
English
17
Connections
This section involves various methods of connecting the product to other external components.
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
Connecting the Speakers
Position of the product
Place it on a stand or cabinet shelf, or under the TV stand.
SW
Selecting the Listening Position
The listening position should be located about 2.5 to 3 times
the distance of the TV's screen size away from the TV.
Example : For 32" TV's 6.56~7.87 feet
For 55" TV's 11.5~13.1 feet
Place these speakers in front of your listening position, facing inwards (about 45°) toward you. Place the
speakers so that their tweeters will be at the same height as your ear. Align the front face of the front
speakers with the front face of the center speaker or place them slightly in front of the center speakers.
Front Speakers
ei
Center Speaker
f
It is best to install it at the same height as the front speakers. You can also install it directly over or
under the TV.
Place these speakers to the side of your listening position. If there isn't enough room, place these
speakers so they face each other. Place them about 2 to 3 feet (60 to 90cm) above your ear,
facing slightly downward.
Surround
Speakershj
Unlike the front and center speakers, the surround speakers are used to handle mainly sound
*
effects and sound will not come from them all the time.
The position of the subwoofer is not so critical. Place it anywhere you like.
Subwoofer
g
Speaker Components
Assembled Speakers
(L) (R)
SCREW (Large): 2EA SCREW (Small): 8EA
CENTER SPEAKER
CENTER
STAND
FRONT
(L) (R)
SURROUND
SPEAKER
STAND BASE
SUBWOOFER
SUBWOOFER
FRONT SPEAKER
SPEAKER CABLE
SURROUND
! CAUTION
Do not let children play with or near the speakers. They could get hurt if a speaker falls.
When connecting the speaker wires to the speakers, make sure that the polarity (+/–) is correct.
Keep the subwoofer speaker out of reach of children so as to prevent children from inserting their hands or alien substances
into the duct (hole) of the subwoofer speaker.
Do not hang the subwoofer on the wall through the duct (hole).
✎ NOTE
If you place a speaker near your TV set, screen color may be distorted because of the magnetic field generated by the
speaker. If this occurs, place the speaker away from your TV set.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
18
Installing the Speakers on the Tallboy Stand
1. Turn the Stand Base upside-down and
1
2
4
connect it to the Stand.
2. Insert four small screws clockwise into the four
holes marked using a screwdriver as shown in the
illustration.
Stand
Base
Stand
3. Connect the upper Speaker to the assembled
Stand.
3
Speaker
4. Insert another large screw clockwise into
the hole on the rear of the speaker using a
screwdriver.
Stand
Connecting The Speakers
1. Press down the terminal tab on the back of the speaker.
2. Insert the black wire into the black terminal (–) and the red wire into
the red (+) terminal, and then release the tab.
3. Connect the connecting plugs to the back of the product by matching
the colors of the speaker plugs to the speaker jacks.
Black
Red
Front Speaker (R)
Center Speaker
Front Speaker (L)
Subwoofer
SPEAKER IMPEDANCE : 3
Surround Speaker (R)
Surround Speaker (L)
FM ANT
iPod
SPEAKER IMPEDANCE
:
3
Download from Www.Somanuals.com. All Manuals Search And Download.
English
19
Connections
Connecting the Optional Wireless Receiver Module
To connect the surround speakers wirelessly, you have to purchase the wireless receiver module and
TX card from your Samsung retailer.
•
This product should be connected with the SWA-5000 only.
Front Speaker (R)
Center Speaker
Front Speaker (L)
Surround
Surround
Subwoofer
Speaker (L)
Speaker (R)
SPEAKER IMPEDANCE
:
3
FM ANT
iPod
SPEAKER IMPEDANCE
:
3
Wireless Receiver Module
Wireless Receiver Module (SWA-5000)
1. Connect the Front, Center and Subwoofer speakers to the product, see
page 19.
FM ANT
DIDITAL
2. With the product turned off, insert the TX card into the TX Card
WIRELESS
AUDIO IN
iPod
Connection(WIRELESS) on the back of the product.
•
Hold the TX card so that the label "WIRELESS" faces upward and
insert the card into the port.
•
The TX card enables communication between the product and the
wireless receiver module.
TX card
3. Connect the left and right surround speakers to the wireless receiver module.
4. Plug the power cord of the wireless receiver module in the wall outlet.
5. Turn on the product. The product and wireless receiver module will now
communicate with each other and you will hear sound from the Surround
speakers.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
20
✎NOTE
Place the wireless receiver module at the rear of the listening position. If the wireless receiver module is
too close to the product, some sound interruption may be heard due to interference.
If you use a device such as a microwave oven, wireless LAN Card or any other device that uses
the same frequency (2.4/5.8GHz) near the product, some sound interruption may be heard due
to interference.
The transmission distance from the product to the wireless receiver module is about 33 feet (10m),
but may vary depending on your operating environment. If a steel-concrete wall or metallic wall is
between the product and the wireless receiver module, the system may not operate at all, because
the radio wave cannot penetrate metal.
If the product doesn't make wireless connection, the system needs ID Setting between the
product and wireless receiver module. With the product turned off, press the remote control's
number buttons "0""1""3""5" and turn on the product. With the wireless receiver module
turned on, press "ID SET" button on the back of the wireless receiver module for 5 seconds.
! CAUTION
Do not insert any other card except the TX card dedicated to the product.
If a different TX card is used, the product may be damaged or the card may not be removed
easily.
Do not insert the TX card upside down or in the reverse direction.
Insert the TX card when the product is turned off. Inserting the card when it is turned on may
cause a problem.
If the TX Card is inserted and wireless receiver module setting is complete, sound is not output
from the Surround Speaker connectors on the product.
The wireless receiving antenna is built into the wireless receiver module. Keep it away from water
and moisture.
For optimal listening performance, make sure that the area around the wireless receiver module
location is clear of any obstructions.
If no sound is heard from the wireless surround speakers, switch the mode to DVD 5.1
channel or Dolby Pro Logic II.
In 2-CH mode, no sound will be heard from the wireless surround speakers.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
21
Connections
Connecting the Video Out to your TV
Choose one of the three methods for connecting to a TV.
METHOD 1
LAN
COMPONENT OUT
HDMI OUT
WIRELESS LAN
AUX IN
VIDEO OUT
HDMI OUT
HDMI IN
METHOD 1 : HDMI (BEST QUALITY)
Connect an HDMI cable (not supplied) from the HDMI OUT jack on the back of the product to the
HDMI IN jack on your TV.
✎ NOTE
Certain HDMI output resolutions may not work, depending on your TV.
If an HDMI cable is connected or removed during playback of a CD-DA, MP3 or JPEG file, the product will
stop playing.
After making the video connection, set the Video input source on your TV to match the corresponding Video
output (HDMI, Component or Composite) on your product.
See your TV owner's manual for more information on how to select the TV's Video Input source.
If you have set the product's remote control to operate your TV, press the TV SOURCE button on the remote
control and select HDMI as the external source of the TV.
HDMI Auto Detection Function
1. Using an HDMI cable, connect the HDMI OUT terminal on the rear of the player to the HDMI IN
terminal of your TV.
2. Turn on the player and TV.
For possible HDMI resolutions, see page 30.
•
•
•
This function is not available if the HDMI cable does not support CEC.
HDMI (High Definition Multimedia Interface)
HDMI is an interface that enables the digital transmission of video and audio data with just a single connector.
Using HDMI, the product transmits a digital video and audio signal and displays a vivid picture on a TV having an HDMI
input jack.
HDMI connection description
- HDMI outputs only a pure digital signal to the TV.
- If your TV does not support HDCP, random noise appears on the screen.
•
•
What is the HDCP?
HDCP (High-band width Digital Content Protection) is a system for protecting BD/DVD content outputted via HDMI from being
copied. It provides a secure digital link between a video source (PC, DVD. etc) and a display device (TV, projector. etc). Content
is encrypted at the source device to prevent unauthorized copies from being made.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
22
Red Blue
Green
METHOD 2
LAN
OMPONNT OUT
METHOD 3
Yellow
VIDEO OUT
WIRELESS LAN
AUX IN
METHOD 2 : Component Video (BETTER QUALITY)
If your television is equipped with Component Video inputs, connect a Component video cable (not
supplied) from the Component Video Output (Pr, Pb and Y) Jacks on the back of the product to the
Component Video Input Jacks on your TV.
✎ NOTE
You can select from a variety of resolution settings such as 1080i, 720p, 480p and 480i, depending on the disc type. (See page 30)
The actual resolution may differ from the setting in the Setup menu if both Component and HDMI cables are connected. The
resolution may also be different depending on the disc. (See page 30)
After making the video connection, set the Video input source on your TV to match the corresponding Video output (HDMI,
Component or Composite) on your product.
See your TV owner's manual for more information on how to select the TV's Video Input source.
If you have set the product's remote control to operate your TV, press the TV SOURCE button on the remote control and select
COMPONENT as the external source of the TV.
In DVD playback, if both HDMI and Component jacks are connected and you select the Component 1080p, 1080i, 720p or 480p
mode, the Display Setup menu will show the output resolution as 1080p, 1080i, 720p or 480p in the menu.
The resolution is actually 480i.
METHOD 3 : Composite Video (GOOD QUALITY)
Connect the supplied Video cable from the VIDEO OUT jack on the back of the product to the VIDEO
IN jack on your TV.
✎NOTE
The VIDEO source is always output in 480i resolution regardless of the resolution set in the Setup menu. (See page 30)
After making the video connection, set the Video input source on your TV to match the corresponding Video output (HDMI,
Component or Composite) on your product.
See your TV owner's manual for more information on how to select the TV's Video Input source.
If you have set the product's remote control to operate your TV, press the TV SOURCE button on the remote control and
select VIDEO as the external source of the TV.
! CAUTION
Do not connect the unit through a VCR. Video signals fed through VCRs may be affected by copyright protection
systems and the picture will be distorted on the television.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
23
Connections
Connecting Audio from External Components
LAN
COMPONENT OUT
DIDITAL
AUDIO IN
HDMI OUT
ESS
OPTICAL
WIRELESS LAN
AUX IN
VIDEO OUT
Red
White
Optical Cable
(not supplied)
Audio Cable
(not supplied)
If the external analog
component has only one
Audio Out, connect either
left or right.
Set-Top Box
OPTICAL
VCR
AUX
OPTICAL : Connecting an External Digital Component
Digital signal components such as a Cable Box/Satellite receiver (Set-Top Box).
1. Connect the Digital Input (OPTICAL) on the product to the Digital Output of the external digital
component.
2. Press the FUNCTION button to select D.IN input.
•
The mode switches as follows : BD/DVD ꢀ D. IN ꢀ AUX ꢀ FM
✎NOTE
To see video from your Cable Box/Satellite receiver, you must connect it's video output to a TV.
This systtem supports Digital sampling frequencies of 32 kHz of higher from external digital components.
This system supports only DTS and Dolby Digital audio, MPEG audio which is bitstream cannot be supported.
AUX : Connecting an External Analog Component
Analog signal components such as a VCR.
1. Connect AUX IN (Audio) on the product to the Audio Out of the external analog component.
•
Be sure to match connector colors.
2. Press the FUNCTION button to select AUX input.
The mode switches as follows : BD/DVD ꢀ D. IN ꢀ AUX ꢀ FM
•
✎NOTE
You can connect the Video Output jack of your VCR to the TV, and connect the Audio Output jacks of
the VCR to this product.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
24
Connecting to the Network
This product enables you to view network based services (See pages 55~60) such as Internet@TV and
BD-LIVE, as well as receive software upgrades when a network connection is made. We recommend
using an AP (Access Point) or IP router for the connection.
For more information on router connection, refer to the user manual of the router or contact the router
manufacturer for technical assistance.
Cable Network
1. Using the Direct LAN Cable (UTP cable), connect the LAN terminal of the product to the LAN
terminal of your modem.
2. Set the network options. (See page 37)
LAN
COMPONENT OUT
HDMI OUT
WIRELESS LAN
AUX IN
VIDEO OUT
Router
Broadband modem
(with integrated router)
Or
Broadband modem
Broadband
Broadband
service
service
Networking with PC for
AllShare function
(See pages 59~60)
✎NOTE
Internet access to Samsung’s software update server may not be allowed, depending on the router you use or the
ISP’s policy. For more information, contact your ISP (Internet Service Provider).
For DSL users, please use a router to make a network connection.
For the AllShare function, a PC must be connected in the network as shown in the figure.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
25
Connections
Connecting to the Network
Wireless Network
You can connect to the network with a Wireless IP sharer.
1. A wireless AP/IP router is required to make a wireless network connection. Connect the wireless
LAN adapter to the Wireless LAN Adapter on the rear panel of the product.
2. Set the network options. (See page 37)
Broadband
LAN
COMPONENT OUT
service
O
I OUT
WIRELESS LAN
AUX IN
VIDEO OUT
Wireless IP sharer
PC
Wireless LAN Adapter
(not included)
Networking with PC for
AllShare function
(See pages 59~60)
✎NOTE
This product is compatible with only Samsung's Wireless LAN Adapter. (not supplied) (Model name: WIS09ABGN).
- The Samsung Wireless LAN Adapter is sold separately. Contact a Samsung Electronics retailer for purchasing.
You must use a wireless IP sharer that supports IEEE 802.11 a/b/g/n. (n is recommended for stable operation of the
wireless network.)
Wireless LAN, by its nature, may cause interference, depending on the use condition (AP performance, distance, obstacles,
interference by other radio devices, etc).
Set the wireless IP sharer to Infrastructure mode. Ad-hoc mode is not supported.
When applying the security key for the AP (wireless IP sharer), only the following is supported.
1) Authentication Mode : WEP, WPAPSK, WPA2PSK
2) Encryption Type : WEP, TKIP, AES
For the AllShare function, a PC must be connected in the network as shown in the figure.
Connecting the FM Antenna
1. Connect the FM antenna supplied to the FM
FM Antenna (supplied)
75Ω COAXIAL Jack.
2. Slowly move the antenna wire around until you
find a location where reception is good, then
fasten it to a wall or other rigid surface.
FM ANT
WI
✎NOTE
iPod
This product does not receive AM broadcasts.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
26
Setup
7. Press the ◄► buttons to the select the
desired Network Settings: Wired, Wireless or
PBC (WPS), then press the ENTER button.
(See pages 37~40)
Before Starting (Initial Setting)
1. Turn on your TV after connecting the product.
(When the product is connected to TV for the first
time, product will turn on automatically and the
Initial Settings screen will be displayed.)
The Network Test will start and Initial Settings
will be completed.
Initial Settings I On-Screen Language
Select a language for the on-screen displays.
Initial Settings I Network
Network Setting is needed to use various Internet services.
Choose the primary method for connecting to network.
English
Français
Deutsch
Español
Italiano
Wired : Set the network by using Ethernet cable.
Please make sure that Ethernet cable is connected.
Wireless
PBC (WPS)
Wired
Nederlands
>Move
s
Select
a
Previous
d
Skip
<
Move
"
Select
2. Press the ▲▼ buttons to select the desired
8. Press the OK button.
language, then press the ENTER button.
The home menu will be displayed. (For more
information about home menu, please see
page 28)
3. Press the ENTER button to select Start button.
Initial Setting
•
Home Menu
TV Aspect, Musical Room Calibration and Network will be set.
Each setting may be changed later under "Settings"
TV service
Please activate Intern
e
t
@
to enjoy a variety of Internet Services.
Start
a
Previous
"
Select
4. Press the ▲▼ buttons to select desired TV
Aspect ratio, then press the ENTER button.
(See page 29)
No Disc
a Change Device
d View Devices
Enter
"
Musical Room Calibration screen will be displayed.
✎ NOTE
5. Plug the ASC microphone into the ASC IN jack
When the product is connected to TV for the
first time, product will turn on automatically.
Do not confuse because this is not
on the product. (See page 33)
6. Press the ENTER button to select Start button.
malfunction.
The home menu will not be displayed if you do
not configure the initial settings.
If you press the BLUE(D) button during the
Musical Room Calibration/Network setup, you
can access the home menu even if the
network setup is not completed yet.
When you return to home menu, the full
screen mode will be cancelled automatically.
Initial Setting I Musical Room Calibration
Preparing...
d Skip
Setting the Musical Room Calibration function
takes about 3 minutes.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
27
Setup
If you want to display Initial Setting screen
1. Press the POWER button.
again in order to make changes, press the
STOP () button on the front panel of the
product for more than 5 seconds with no disc
inserted.
Use the HDMI cable to connect the product to
an Anynet+(HDMI-CEC)-compliant Samsung TV.
If the TV uses a language supported by the
product, that language will be set to a
preferred language automatically.
The Home Menu will appear.
•
Home Menu
TV service
Please activate Intern
e
t
@
to enjoy a variety of Internet Services.
2
3
4
However, the Anynet+(HDMI-CEC) feature
should be set to On in both TV and the
product.
If the product is left in the stop mode for more
than 5 minutes without being operated, a
screen saver will appear on your TV. If the
product is left in the screen saver mode for
more than 25 minutes, the power will
automatically turn off except during playback
of a CD-DA (Automatic Power-Off Function).
1
5
6
No Disc
a Change Device
d View Devices
Enter
"
Selects the Internet@TV.
Selects the Videos.
1
2
3
4
5
6
Selects the Music.
Selects the Photos.
Selects the Settings.
Displays buttons available.
Setting the Menu
DISC MENU
TITLE MENU
POPUP
2. Press the ◄► buttons to select Settings,
1
2
then press the ENTER button.
TOOLS
INFO
3. Press the ▲▼ buttons to select the desired
submenu, then press the ENTER button.
4. Press the ▲▼ buttons to select the desired
item, then press the ENTER button.
3
4
5. Press the EXIT button to exit the menu.
TUNER
NOTE
✎
When the product is connected to the network,
select Internet@TV from the home menu.
Download desired content from Samsung AppS.
The access step may differ depending on the
selected menu.
The OSD (On Screen Display) may change in
this product after upgrading the software
version.
1
MENU Button : Press this to move to the home menu.
2
3
4
RETURN Button : Return to the previous menu.
ENTER / DIRECTION Button:
Press the arrow buttons to move the cursor and select
an item.
Press the ENTER button to launch the selected item or
confirm the setting.
EXIT Button : Press this to exit the menu.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
28
If you select the 16:9 Normal, 4:3 Pillarbox may be
displayed. In this case, you can't see full screen by
pressing the FULL SCREEN button on the remote control.
Display
You can configure various display options such as
the TV Aspect, Resolution, etc.
BD Wise (Samsung Products only)
TV Aspect
BD Wise is Samsung's latest inter-connectivity feature.
Depending on the type of television you have, you
may want to adjust the screen setting.
When you connect Samsung products with
BD-Wise to each other via HDMI, the optimum
resolution will be set automatically.
•
•
•
16:9 Normal
•
Off : The output resolution will be fixed
according to the Resolution previously set,
regardless of the resolution of the disc.
Certain movies(4:3 source)
will be displayed in 4:3
Pillarbox (black bars on sides
of picture) if 16:9 normal is
selected.
•
On : The original resolution of the BD/DVD disc
will be output to the TV.
NOTE
✎
16:9 Wide
If you want to change the resolution in BD
Wise, you must set BD Wise to Off in advance.
If you set off the BD Wise, the resolution of the
connected TV will be adjusted to its maximum
resolution automatically.
If the product is connected to a device that
does not support BD Wise, you can not use
BD Wise function.
For a proper operation of BD Wise, set each BD Wise
menu of the product and the TV to On respectively.
You can view the full 16:9
picture on your widescreen
TV.
4:3 Letter Box
Select when you want to see
the total 16:9 ratio screen
Blu-ray Disc/DVD supplies,
even though you have a TV
with a 4:3 ratio screen. Black
bars will appear at the top
and bottom of the screen.
Resolution
Sets the output resolution of the Component and
HDMI video signal.
The number in 1080p, 1080i, 720p, 480p, 480i
indicates the number of lines of video.
The i and p indicate interlace and progressive
scan, respectively.
•
4:3 Pan-Scan
Select when you want to see
the 16:9 video supplied by the
Blu-ray Disc/DVD without the
black bars on top and bottom,
even though you have a TV
with a 4:3 ratio screen(extreme
left and right portion of the
movie picture will be cut off).
•
Auto : It automatically checks and sets the optimal
resolution. (HDMI only)
•
BD Wise : Automatically sets the optimal
resolution when connected via HDMI to a TV with
the BD Wise feature. (The BD Wise menu item
appears only if BD Wise is set to On.) (HDMI only)
NOTE
✎
•
•
•
•
•
1080p : Outputs 1080 lines of progressive video. (HDMI only)
1080i : Outputs 1080 lines of interlaced video.
720p : Outputs 720 lines of progressive video.
480p : Outputs 480 lines of progressive video.
480i : Outputs 480 lines of interlaced video.
(Component & VIDEO only)
Depending on the disc type, some aspect ratios
may not be available.
If you select an aspect ratio and option which is
different than the aspect ratio of your TV screen,
then the picture might appear to be distorted.
If you select the 4:3 Pan-Scan or 4:3 Letter Box,
you can't see full screen by pressing the FULL
SCREEN button on the remote control.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
29
Setup
Resolution according to the output mode
•
Blu-ray Disc playback
HDMI / connected
HDMI / not connected
Output
Setup
HDMI Mode
Component/VIDEO Mode
Component Mode
VIDEO Mode
Auto
Optimal Resolution
1080p@60F
480i
480i
-
-
-
-
1080p, Movie Frame(24Fs) off
1080p/1080i,
Movie Frame(24Fs) on
1080p@24F
480i
-
-
1080i, Movie Frame(24Fs) off
1080i
720p
480p
-
480i
480i
480i
-
1080i
720p
480p
480i
480i
480i
480i
480i
720p
480p
480i
•
DVD playback
HDMI / connected
HDMI / not connected
Output
Setup
HDMI Mode
Optimal Resolution
1080p@60F
1080i
Component/VIDEO Mode
Component Mode
VIDEO Mode
Auto
1080p
1080i
720p
480p
480i
480i
480i
480i
480i
480i
-
-
-
-
-
480p
480p
480p
480i
480i
480i
480i
480i
720p
480p
-
NOTE
✎
If the connected TV does not support Movie
Frame or the selected resolution, the message
“If no pictures are shown after the selection,
please wait for 15 seconds. And then, the
resolution will be reverted to the previous value
automatically. Would you like to make a
selection?” will be displayed.
The Blu-ray Disc must have the 24 frame
feature in order to use the Movie Frame (24Fs)
mode.
If both HDMI and Component jacks are
connected and you are currently viewing
component output, there is a difference
between resolution table and actual resolution
depending on your TV.
If you select Yes and the resolution is not
supported, the TV's screen will be blank.
Please wait for 15 seconds and the resolution
will be reverted to the previous value
automatically.
If the HDMI Auto Detection feature does not
work, you can't select the 1080p resolution or
Movie Frame (24Fs).
If the screen is blank, press and hold the
STOP () button on the front of the product
for more than 5 seconds (no disc inserted).
All settings are restored to the factory default.
Follow the steps on the previous page to
access each mode and select the Display
Setup that your TV will support.
When the factory default settings are restored,
all the user data stored in the BD data will be
deleted.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
30
HDMI Format
Progressive Mode
You can optimize the color setting from the HDMI
output. Select a connected device Type.
Set to improve picture quality when viewing DVDs.
•
Auto : Select this to have the product
automatically set the best picture for the DVD
you're watching.
•
•
TV : Select if connected to a TV via HDMI.
Monitor : Select if connected to a Monitor via
HDMI.
•
Video : Select this for the best picture from
Concert or TV show DVDs.
✎NOTE
A TV or monitor has to be connected to the
product before you select this option.
Still Mode
Set the type of picture shown when you pause
DVD playback.
Movie Frame (24 Fs)
•
•
•
Auto: Automatically set the best still picture
depending on the content.
Frame : Select when pausing a scene with a
little action.
Setting the Movie Frame (24Fs) feature to On
allows you to adjust the product's HDMI output to
24 frames per second for improved picture quality.
You can enjoy the Movie Frame (24Fs) feature only
on a TV supporting this frame rate. This menu can
only be selected in 1080i or 1080p HDMI output
resolution modes.
Field : Select when pausing a scene with a lot
of action.
•
Off : Movie Frame (24Fs) functions will not
work.
HDMI Deep Color
Set to output the picture from the HDMI OUT
jack with Deep Color or not. Deep Color allows
more accurate color reproduction with deeper
color depth.
•
On : Movie Frame (24Fs) functions will work.
✎NOTE
Two types of frame rates may be included,
•
Auto: The picture will be output with Deep
Color to the connected TV which supports
HDMI Deep Color.
depending on the disc: Movie material (24
frame) and Video material (30 frame). When the
setting switches between Movie (24 frame) and
Video (30 frame), the screen may blink for a
few seconds.
•
Off : The picture will be output without Deep
Color.
If your TV does not support Movie Frame
(24Fs) function, the pop-up message will be
displayed.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
31
Setup
Distance
Audio
If the speakers cannot be placed at equal
Speaker Setting
distances from the listening position, you can
adjust the delay time of the audio signals from the
front, center, surround and subwoofer speakers.
Settings
Speaker Setting
•
You can set the Speaker Distance between
1ft(0.3m) and 30ft(9.0m).
Display
Audio
Level
|
Distance
Test tone
System
Networ
Langua
Security
General
Support
:
Off
Settings
Distance
Front L
:
:
:
:
:
:
:
◄
10ft (3.0m) |
10ft (3.0m)
10ft (3.0m)
10ft (3.0m)
10ft (3.0m)
10ft (3.0m)
Off
Display
Audio
Front R
Center
sSelect rReturn
Surround L
Surround R
Subwoofer
Test Tone
System
Network
Languag
Security
General
Support
Set the speaker level and distance to obtain the best possible surround sound.
<Change sSelect rReturn
Level
Set the parameters of the distance from the listening position to the speakers.
You can adjust the balance and level for each
speaker.
Test Tone
Adjusting Front/Center/Surround/Subwoofer
Speaker Level
Use the Test Tone feature to check the speaker
connections.
• The volume level can be adjusted in steps from
+6dB to -6dB.
• The sound gets louder as you move closer to
+6dB and quieter as you get closer to -6dB.
Press the ◄, ► buttons to select All.
•
A test tone will be sent to Front Left ꢀ Center
ꢀ Front Right ꢀ Surround Right ꢀ
Surround Left ꢀ Subwoofer in order so you
can make sure the speakers are set up
correctly.
Settings
Level
Front L
:
:
:
:
:
:
:
◄
0 dB
0 dB
0 dB
0 dB
0 dB
0 dB
Off
|
Display
Audio
Front R
Center
System
Networ
Langua
Security
General
Support
Surround L
Surround R
Subwoofer
Test Tone
To stop the test tone, press the ◄, ► buttons to
select Off.
<Change sSelect rReturn
Settings
Speaker Setting
Set the speaker level to obtain the best possible surround sound.
Level
Display
Distance
Test Tone
Audio
System
Network
Languag
Security
General
Support
:
◄
All
|
<Change sSelect rReturn
Listen to the emitted sound from all speakers in sequence.
✎NOTE
When HDMI Audio is ON (audio is produced
through TV speakers), the Test Tone
function is not available.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
32
✎
NOTE
Musical Room Calibration
Setting the Musical Room Calibration
function takes about 3 minutes.
The Musical Room Calibration setup can be made
when there is no disc in the product.
If the ASC microphone is disconnected during the
Musical Room Calibration setup, the setup will be
canceled.
When the Musical Room Calibration function is
activated, the DSP, Dolby Pro Logic ll and SFE
Mode will not work.
If the product is connected to external devices or
other components (such as an iPod, AUX, D.IN),
the Musical Room Calibration Setup may not work
properly.
By setting the Musical Room Calibration (MRC)
function just once when you relocate or install the
product, you can have the product automatically
recognize the distance between speakers, levels
between channels, and frequency characteristics
to create a 5.1-channel sound field optimized for
your environment.
ASN
EQ Optimizer
ASC
microphone
Set optimal EQ automatically depending on the
region.
•
Off : Turn EQ Optimizer off.
•
On : Turn EQ Optimizer on.
HDMI Audio
Musical Room Calibration
The audio signals transmitted over the HDMI
Cable can be toggled On/Off.
You will hear either the Musical Room Calibration
mode or the User Speaker Settings.
•
Off : Video is transmitted over the HDMI
connection cable only, and audio is output
through your product speakers only.
•
Off: You will hear sound in the the Speaker
Setting value.
•
On: You will hear sound in the Musical Room
Calibration mode.
•
On : Both video and audio signals are
transmitted over the HDMI connection cable,
and audio is output through your TV speakers
only.
Musical Room Calibration Setting
1. Plug the ASC microphone into the ASC IN jack.
2. Place the ASC microphone at the listening position.
✎NOTE
HDMI Audio is automatically down-mixed to
2ch for TV speakers.
•
Musical Room Calibration will be automatically
set up in the following sequence:
Front Left
ꢀ
Center
ꢀ
Front Right
ꢀ
ꢀ
Surround Right
Subwoofer
ꢀ
Surround Left
•
•
Press the RETURN button to cancel the
Musical Room Calibration Setting.
When the message "REMOVE MIC" appears
in the display, unplug the ASC microphone.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
33
Setup
✎
NOTE
Digital Output
Be sure to select the correct Digital Output
or you will hear no sound or a loud noise.
If the HDMI device (Receiver, TV) is not compatible
with compressed formats (Dolby digital, DTS), the
audio signal outputs as PCM.
Secondary and Effect audio will not be heard with
regular DVDs.
Some Blu-ray Discs do not have Secondary and
Effect audio.
This Digital Output setup does not effect the
analog (L/R) audio or HDMI audio output to your
TV.
It effects the optical and HDMI audio output when
connected to a receiver.
If you play MPEG audio soundtracks, audio signal
outputs PCM regardless of Digital Output
Selections (PCM or Bitstream).
Set Digital output depending on the connected
receiver. (For more details, please refer to the
digital output selection.)
•
•
•
PCM
Bistream(Re-encode)
Bistream(Audiophile)
Blu-ray Discs may include three audio streams.
- Primary Audio : The audio soundtrack of the
main feature.
-
Secondary Audio : Additional soundtrack
such as director or actor's commentary.
- Interactive Audio : Interactive sounds will be
heard when selected. Interactive Audio is
different on each Blu-ray Disc.
Digital Output Selection
Bitstream
Bitstream
Setup
PCM
HDMI Receiver
(Re-encode)
(Audiophile)
Connection
Optical
PCM 2ch
PCM 2ch
HDMI Receiver or Optical HDMI Receiver
Optical
PCM 2ch
PCM
Up to 7.1ch
Up to 5.1ch
DTS re-encoded
DTS re-encoded
PCM
Dolby Digital
Dolby Digital
Dolby Digital
Dolby Digital
Plus
Up to 7.1ch
PCM 2ch
DTS re-encoded
Dolby Digital Plus
Dolby Digital
Audio Stream
on Blu-ray Disc Dolby TrueHD
Up to 7.1ch
Up to 6.1ch
Up to 7.1ch
Up to 7.1ch
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
DTS re-encoded
DTS re-encoded
DTS re-encoded
DTS re-encoded
PCM 2ch
Dolby TrueHD
DTS
Dolby Digital
DTS
DTS
DTS-HD HRA
DTS-HD MA
PCM
DTS-HD HRA
DTS-HD MA
PCM 2ch
Dolby Digital
DTS
DTS
DTS
PCM 2ch
Dolby Digital
DTS
Audio Stream
Dolby Digital
on DVD
Up to 5.1ch
Up to 6.1ch
Dolby Digital
DTS
DTS
Outputs only the Primary audio
soundtrack (main soundtrack of the
movie) so that your receiver can decode
the audio bitstream. You will not hear
Secondary and Effect audio.
Decodes Primary, Secondary and
Effect audio streams together into
PCM audio, then re-encodes the
PCM audio into DTS bitstream.
Decodes Primary, Secondary and
Effect audio streams together into
PCM audio.
Definition for
Any
Blu-ray Disc
Download from Www.Somanuals.com. All Manuals Search And Download.
English
34
Dynamic Range Control
Anynet+(HDMI-CEC)
You can listen at low volumes but still hear dialog
clearly. This is only active when a Dolby Digital
signal is detected.
Anynet+ is a convenient function that offers linked
operations with other Samsung products with the
Anynet+ feature.
•
Off : You can enjoy the movie with the
standard Dynamic Range.
To operate this function, connect this product to
a Samsung TV with an HDMI cable.
You can operate this product using a Samsung
TV remote control and start disc playback simply
by pressing the PLAY (►) button on the TV’s
remote control.
•
On : When Movie soundtracks are played at
low volume or from smaller speakers, the
system can apply appropriate compression to
make low-level content more intelligible and
prevent dramatic passages from getting too
loud.
For more information, please see the TV user
manual.
•
•
Off : Anynet+ function will not work.
On : Anynet+ functions will work.
AV Sync
Video may look slower than the audio when the
product is connected to a digital TV. If this
occurs, adjust the audio delay time to match the
video.
NOTE
✎
This function is not available if the HDMI cable
does not support CEC.
If your Samsung TV has an
it supports the Anynet+ function.
n
logo, then
•
You can set the audio delay time between
0 msec and 300 msec. Set it to the optimal
status.
Depending on your TV, certain HDMI output
resolutions may not work.
Please refer to the user manual of your TV.
System
BD Data Management
Initial Setting
Enables you to manage the downloaded
contents from the Blu-ray disc that supports the
BD-LIVE service.
You can check the device information including
the storage size, and delete the BD data or
change the device.
By using the Initial Setting, you can set language,
TV aspect, Musical Room Calibration and
Network setting, etc.
For more information on the settings, refer to the
corresponding section in this user manual.
Internet@TV Screen Size
*
You must have a minimum 1GB USB Memory
device inserted in one of the USB slots (The
Wireless LAN Jack also functions as a USB slot.)
in order to download content from BD-LIVE.
Set the Internet@TV screen size to display
Internet@TV screen in optimal size on your TV.
•
•
•
Size 1 : Select when connected to the TV
using the component or Video output jack.
Settings
Size 2 : Select when connected to the TV
using the HDMI cable.
Size 3 : Select when connected to the TV
using the HDMI cable and the TV set to be
displayed in full screen.
Display
Audio
BD Data Management
External Flash Memory
Current Device
:
System
Network
Language
Security
General
Support
Total Size
: 955MB
: 949MB
Available Size
Delete BD Data
Change Device
|
:
External Flash Memory
sSelect
rReturn
Delete all BD data in the storage.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
35
Setup
Description of Device(Storage) Information on
the Product
DivX(R) Registration
View DivX(R) VOD Registration Code to purchase
and play DivX(R) VOD content.
•
•
Total Size : Total size of the Device (Storage).
Available Size : Available size of the Device (Storage).
NOTE
Settings
✎
In the external memory mode, disc playback
will be stopped if you disconnect the USB
device in the middle of the playback.
Only those USB devices formatted in FAT file
system (DOS 8.3 volume label) are supported,
and it is recommended to use USB devices
that support USB 2.0 protocol, 4 MB/sec or
faster read/write speed.
Display
Audio
Initial Setting
Disc Menu
DivX(R) Video On Demand
:
System
Network
Language
Security
General
Support
Your registration code is : XXXXXXXXXX
OK
A USB HDD device cannot be used for BD
Data storage (BD-LIVE).
✎ NOTE
The Resume Play function may not work after
formatting the storage device.
This option is not activated if you select OK.
To activate this option, please activate the
DivX(R) Deactivation.
The total size of BD Data Management may
differ, depending on the software version.
Clock
DivX(R) Deactivation
Set time-related functions.
Select this to get a new registration code.
Settings
Settings
Display
Audio
System
Networ
Clock
Display
Audio
Initial Setting
Disc Menu
Clock Mode
Clock Set
: Auto
|
:
System
Network
Language
Security
General
Support
Time Zone
: GMT + 0:00
: Off
Do you want to deactivate your device?
Langua
DST
Security
General
Support
Yes
No
>Move sSelect rReturn
Choose your preferred method of setting clock.
✎NOTE
•
Clock Mode : You can select Auto or Manual.
If you select Manual, the Clock Set menu will
be activated while DST will be deactivated.
Clock Set : You can specify the current time
and date manually.
Time Zone : You can specify the time zone
that is applicable to your area.
DST : You can set DST (Daylight Saving Time)
1 hour, 2 hour and off.
This function can be operated when DivX(R)
Registration function is deactivated.
•
•
•
Download from Www.Somanuals.com. All Manuals Search And Download.
English
36
Network Setup
Settings
Displa
Network Settings
To begin setting up the network connection for
your product, follow these steps:
Internet Protocol Setup : Auto
\
Audio
IP Address
:
:
:
0
0
0
0
0
0
0
0
0
0
0
0
System
Netwo
Langu
Subnet Mask
Gateway
1. In the Home menu, press the ◄► buttons to
select the Settings, and then press the
ENTER button.
DNS
: Auto
Securi
Gener
Suppo
DNS Server
:
0
0
0
0
>Move
"
Select
'
Return
2. Press the ▲▼ buttons to select Network,
and then press the ENTER button.
3. Press the ▲▼ buttons to select Network
2. After the Network Function has acquired the
network values, press the RETURN button.
Then, run a Network Test to ensure the
product has connected to your network (See
page 40).
3. If the Network Function does not acquire the
network values or you selected Manual, go to
the directions for Manual Setup.
Settings, and then press the ENTER button.
4. Press the ▲▼ buttons to select Network
Type, and then press the ENTER button.
5. Press the ▲▼ buttons to select Wired or
Wireless, and then press the ENTER button.
6. Go to the next section.
Network Settings
Setting Up a Wired Connecton - Manual
Please contact your ISP to find out if your IP
address is static or dynamic. If it is dynamic, we
recommend using the Auto setting. This is the
easiest and will work in the majority of cases. If it is
static, you must use the manual set up procedure.
If the Auto Setting does not work, you’ll need to set
the Network Setting values manually.
To get the Network setting values from most
Windows computers, follow these steps:
Directions for wired networks are below. Directions
for wireless networks are after the directions for
wired networks.
1. Right click the Network icon on the bottom
right of the screen.
2. In the pop-up menu, click Status.
3. On the dialog that appears, click the Support
Wired Network
tab.
1. In the Network Settings menu, press the
▲▼ buttons to select Network Settings,
and then press the ENTER button.
4. On the Support tab, click the Details button.
The Network settings are displayed.
To enter the Network settings into your product,
follow these steps:
The Internet Protocol Setup screen appears.
2. Press the ► button, then select Auto or
Manual, and then press the ENTER button.
1. On the Internet Protocol Setup screen, press
the ENTER button.
Setting Up a Wired Connecton - Auto
2. Press the ▲▼ buttons to select Manual,
1. If you selected Auto, the Network Function
acquires and fills in the values for IP Address,
Subnet Mask, etc., automatically.
and then press the ENTER button.
3. Press the ▼ button to go to the first entry
field (IP Address).
✎NOTE
This process can take up to five minutes.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
37
Setup
2. Press the RED(A) button on the remote
Settings
control.
Network Settings
Displa
Audio
Internet Protocol Setup : Manual
\
3. Press the PBC (WPS) button on your router
within two minutes. Your product displays
the Network Selection Screen, and
automatically acquires all the network
setting values it needs and connects to your
network. When it is done, it displays an OK
button. Press the ENTER button on your
remote.
IP Address
:
:
:
0
0
0
0
0
0
Syste
Netwo
Langu
Secur
Gener
Suppo
Subnet Mask
Gateway
255 255 255
0
0
0
DNS
: Manual
DNS Server
:
0
0
0
0
>Move
"
Select
'
Return
Select to configure your network type and IP address, or to perform a Network Test.
4. After the network connection is set up,
press the RETURN button to exit the
Network Setting screen.
4. Use the number buttons on your remote to
enter numbers.
5. When done with each field, use the ►
button to move successively to the next
field.
Setting Up the Wireless Network
Connection - Auto Network Search
You can also use the other arrow buttons to
move up, down, and back.
Most wireless networks have an optional security
system that requires devices that access the
network to transmit an encrypted security code
called an Access or Security Key. The Security Key
is based on a Pass Phrase, typically a word or a
series of letters and numbers of a specified length
you were asked to enter when you set up security
for your wireless network. If you use this method
of setting up the network connection, and have
a Security Key for your wireless network, you will
have to enter the Pass Phrase during the setup
process.
6. Enter the IP Address, Subnet Mask, and
Gateway values.
7. Press the ▼ button to go to DNS.
8. Press the ▼ button to go to the first DNS
entry field. Enter the numbers as above.
9. Press the RETURN button on your remote.
10. Run a Network Test to ensure the product
has connected to your network (See page
40).
Setting Up the Network Connection
Wireless Network
To set up the wireless connection using Auto
Network Search, follow these steps:
You can setup the wireless network three ways:
1. In the Network Settings menu, press the
▲▼ buttons to select Network Settings,
and then press the ENTER button.
•
•
•
Using PBC (WPS)
Using the Auto Network Search function.
Manually.
The Internet Protocol Setup screen appears.
Each method is described below.
2. Press the ▲▼ buttons to select the
Internet Protocol Setup, and then press
the ENTER button.
Setting Up the Wireless Network
Connection - PBC (WPS)
3. Press the ▲▼ buttons to select Auto or
Manual, and then press the ENTER button.
The easiest way to set up the wireless network
connection is using the PBC (WPS) function.
If your wireless router has a PBC (WPS) button,
follow these steps:
4. If you selected Auto, press the ▲ button to
go to Access Point Selection, and then
press the ENTER button.
The Network function searches for available
wireless networks.
When done, it displays a list of the available
networks.
1. In the Network Settings menu, press the
▲▼ buttons to select Network Settings,
and then press the ENTER button.
The Internet Protocol Setup screen appears.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
38
10. When done, press the YELLOW(C) button
on your remote, or move to the Done
Settings
Display
Audio
Network Settings
Network Selection
button, and then press the ENTER button.
The Network Connecting screen appears.
System
Networ
Langua
Securit
General
Support
Connecting to network.
Network Name(SSID) : shj
11. Wait until the connection confirmation
message is displayed, and then press the
ENTER button. The Network Settings
screen reappears.
Stop
"
Select
'
Return
12. To test the connection, press the ▼ button
to select Network Test, and then press the
ENTER button.
5. In the list of networks, press the ▲▼
buttons to select a network, and then press
the ENTER button.
6. If the PIN/Security pop-up appears, go to
Step 7. If the Network Connecting Screen
appears, go to Step 11.
Setting Up the Wireless Network
Connection - Manual
If the Auto Setting does not work, you need to
enter the Network settng values manually.
To get the Network setting values from most
7. Press the ▲▼ buttons to select PIN or
Security.
Windows computers, follow these steps:
For most home networks, you would select
Security (for Security Key).
1. Right click the Network icon on the bottom
right of the screen.
8. On the Security screen, enter your network’s
2. In the pop-up menu, click Status.
Pass Phrase.
3. On the dialog that appears, click the
Support tab.
✎NOTE
You should be able to find the Pass Phrase
on one of the set up screens you used to set
up your router or modem.
4. On the Support tab, click the Details button.
The Network settings are displayed.
To Enter the Network settings into your product,
follow these steps:
9. To enter the Pass Phrase, follow these
general directions:
1. On the Internet Protocol Setup screen,
•
Press the number keys on your remote to
press the ENTER button.
enter numbers.
2. Press the ▲▼ buttons to select Manual,
•
Use the arrow keys on your remote to
move from button to button on the
Security Key screen.
and then press the ENTER button.
3. Press the ▼ button to go to the first entry
field (IP Address).
•
To enter letters, move to the button
labeled a/A/1/, and then press the
ENTER button. Each time you press the
ENTER button, you change the kind of
characters you can enter (a/A/1/).
To enter a letter, press the number button
that corresponds to the letter. Pressing
the button repeatedly changes the letter.
To delete the last letter or number you
entered, move to the Delete button, and
then press the ENTER button.
4. Use the number buttons to enter numbers.
Settings
Network Settings
Displa
Audio
System
Netwo
Langu
Securi
Access Point Selection : Not Selected
\
•
•
•
Internet Protocol Setup : Manual
IP Address
Subnet Mask
Gateway
:
:
:
0
0
0
0
0
0
255 255 255
0
0
0
DNS
: Manual
Gener
Suppo
DNS Server
:
0
0
0
0
a PBC (WPS) >Move
"
Select
'
Return
To clear all entered letters and numbers,
move to the Clear key, and then press the
ENTER button. You can also just press
the RED(A) button on your remote.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
39
Setup
5. When done with each field, use the ►
button to move successively to the next
field.
BD-LIVE Internet Connection
Set whether to allow internet connection when
BD-LIVE service is used.
You can also use the other arrow buttons to
move up, down, and back.
•
Allow (All) : The Internet connection will be
allowed for all BD-LIVE contents.
6. Enter the IP Address, Subnet Mask, and
•
Allow (Valid Only) : The Internet connection
will be allowed only for BD-LIVE contents
containing a valid certificate.
Gateway values.
7. Press the ▼ to go to DNS.
8. Press the ▼ button to go to the first DNS
•
Prohibit : No Internet connection will be
allowed for any BD-LIVE content.
entry field. Enter the numbers as above.
9. When done, press the ▲ button to return to
Access Point Selection. Select the network,
and then press the ENTER button.
10. Go to Step 6 in the Automatic Wireless
procedure above, and follow the directions
from that point on.
NOTE
✎
What is a valid certificate?
When the product uses BD-LIVE to send the
disc data and request to the server to certify
the disc, the server uses the transferred data
to check if the disc is valid and sends the
certificate back to the product.
Network Test
Use this menu to connect the wired network or
check whether your network connection is
working or not.
The Internet connection may be restricted
while you are using BD-LIVE contents.
Settings
Language
Display
Audio
Network Test
MAC Address (00:00:00:00:00:00)
You can select the language you prefer for home
menu, disc menu, etc.
On-Screen Menu : Select the language for the
on-screen displays.
System
Network
Languag
Security
General
Support
IP Address,Subnet Mask,Gateway,DNS Server
Gateway Ping
Internet Service Test
•
Network testing...
•
Disc Menu : Select the language for the disc
Test your Internet Protocol setup to see if it works correctly.
menu displays.
•
•
Audio : Select the language for disc audio.
Subtitle : Select the language for disc subtitles.
Network Status
NOTE
✎
The selected language will only appear if it is
supported on the disc.
Check whether a connection to the network and
the Internet have been established.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
40
Security
General
When you operate this menu for the first time,
password setup screen will be displayed. Enter
the desired 4-digit password using the number
buttons. (Default password is set to 0000.)
Background
Change the background theme of the menu
screen.
Parental Rating
Settings
This function works in conjunction with Blu-ray
Disc/DVDs that have been assigned a rating,
which helps you control the types of Blu-ray Disc/
DVDs that your family watches.
Select the rating level you want to set. A larger
number indicates that the program is intended for
adult use only. For example, if you select up to
Level 6, discs that contain Level 7, 8 will not play.
Background
Skin 1
Skin 2
Skin 3
Skin 4
Skin 5
lect rReturn
Settings
Display
Audio
Parental Rating
Change Password
Off
8(Adults)
Energy Saving
System
Network
Language
Security
General
Support
7
6
5
4
You can reduce power consumption by setting
the front panel to turn off automatically when
there is no operation for 5 seconds.
▼
•
Off : Energy Saving function is not used.
•
On : The front panel will automatically turn off
when there is no operation for 5 seconds.
Change Password
Change the 4-digit password used to access
security functions.
Front Display
Change the brightness of the front panel.
Settings
•
•
•
Auto : Dim during playback only.
Dim : Dim the display window.
Bright : Brighten the display window.
Change Password
Enter the password
Display
Audio
System
Networ
Langua
Securit
Genera
Suppor
Power On/Off Sound
Enter Pin rReturn
Play a melody when the product is turned on and
off.
•
Off : Turn Power Sound Off.
If you forgot your password
•
On : Turn Power Sound On.
1. Remove the disc.
2. Press and hold the STOP () button on the
front panel for 5 seconds or more.
All settings will revert to the factory settings.
NOTE
✎
When the factory default settings are restored, all the
user data stored in the BD data will be deleted.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
41
Setup
You can update software in any of the two ways
as follows: Software update is the same as in the
By Internet menu.
Support
Software Upgrade
•
then download and store the latest software
(RUF file) into the USB flash drive. Connect the
USB flash drive to the USB port of the product
(disc tray must be empty) to update the
software, then follow the on-screen
instructions.
This menu allows you to upgrade software for
performance improvements or additional services.
You can check the current software version,
upgrade by internet and set the Auto upgrade
notification. If the product is properly connected to
the network by cable or wirelessly, the product will
automatically connect to our website each time it is
turned on and download update files if any valid
upgrade exists.
•
download and write the latest software (RUF
file) onto a disc. Insert and play the disc in the
product to start the update, then follow the on-
screen instructions.
Settings
Display
Audio
Software Upgrade
Software Upgrade
NOTE
✎
Syste
Current Version
: XXX-XXXXXXXXX
Netwo
By Internet
Langu
Auto Upgrade Notification : On
Secur
Gener
Support
|
Software upgrades using the USB Host jack
must be performed with no disc inside.
sSelect rReturn
If you want to cancel the upgrade in the
process of downloading the upgrade data,
press the ENTER button.
When the system upgrade is done, check the
software details in the software Upgrade
menu.
Do not turn off the product during the System
Upgrade, as it may cause the product to not
work properly.
Do not use USB devices other than USB Flash
Drives to do software upgrades when using
the USB Host jack.
1. To select By Internet, press the ENTER
button.
A popup message will appear if an update is
available.
2. If you select Yes, the product will turn off
automatically before restarting.
(Never turn it on manually.)
3. The update progress popup will appear.
When the update is completed, the product
will turn back off automatically.
Contact Samsung
4. Press the POWER button to turn on the
product.
Provide contact information for assistance with
your product.
NOTE
✎
The Update will be completed when the
product turns off after restarting. Press the
POWER button to turn on the updated product
for your use.
Never turn off or on the product manually during
the update process.
Samsung Electronics shall take no legal
responsibility for product malfunction caused by
unstable of internet connection or consumer
negligence during software upgrade.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
42
Basic Functions
Disc Structure
Playing a Disc
The contents of disc are usually divided as below.
Playback
•
Blu-ray Disc, DVD-VIDEO
1. Press the OPEN/CLOSE ( ) button to open
title 1
title 2
chapter 2
the disc tray.
chapter 1
chapter 2
chapter 1
chapter 3
2. Place a disc gently into the tray with the
disc’s label facing up.
•
•
Audio CD (CD-DA)
track 1 track 2
3. Press the PLAY (►) button or OPEN/
track 3
track 4
track 5
CLOSE ( ) button to close the disc tray.
MP3, WMA, DivX, MKV and MP4
folder (group) 1
file 1 file 2
Playback related buttons
folder (group) 2
file 2
file 1
file 3
PLAY ( ►)
Starts playback.
Stops playback.
Using the Disc menu / Title menu / Popup menu
•
If pressing the button once:
The stop position will be
memorized.
Using the Disc Menu
•
If pressing the button twice:
The stop position will be not
memorized.
STOP ( )
hZ
1. During playback, press the DISC
MENU button on the remote
control.
DISC MENU
(With some Blu-ray discs (BD-J),
this function may not work.)
2. Press the ▲▼◄ ► buttons to make
the desired selection, then press the
ENTER button.
PAUSE ( )
Pauses playback.
✎NOTE
✎NOTE
Depending on the disc, the menu items may
differ and this menu may not be available.
"Not Available" will appear when an invalid
button is pressed.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
43
Basic Functions
Using the Title Menu
Using the Search and Skip Functions
During playback, you can search quickly through
a chapter or track, and use the skip function to
jump to the next selection.
Z
TITLE MENU
1. During playback, press the TITLE
MENU button on the remote
control.
2. Press the ▲▼◄ ► buttons to
make the desired selection, then
press the ENTER button.
POPUP
Searching for a Desired Scene
hzZyx
During playback, press the SEARCH ()
•
✎NOTE
button.
Depending on the disc, the menu items may
Each time you press the SEARCH ()
button, the playback speed will change as
follows.
differ and this menu may not be available.
The Title Menu will only be displayed if there
are at least two titles on the disc.
BD-ROM,
) 1 ) 2 ) 3
BD-RE/-R,
) 4 ) 5 ) 6 ) 7
Playing the Title List
DVD-RW/-R,
( 1 ( 2 ( 3
( 4 ( 5 ( 6 ( 7
DVD+RW/+R,
DVD-VIDEO
z
DISC MENU
) 1 ) 2 ) 3
( 1 ( 2 ( 3
1. During playback, press the DISC
DivX, MKV, MP4
MENU or TITLE MENU button.
TITLE MENU
POPUP
2. Press the ▲▼ buttons to select
an entry you want to play from
Title List, then press the ENTER
button.
•
To return to normal speed playback, press the
PLAY (►) button.
NOTE
✎
No sound is heard during search mode.
Using the Popup Menu
Skipping Chapters
h
TITLE MENU
1. During playback, press the POPUP
hzZyx
During playback, press the SKIP (#$)
POPUP
button on the remote control.
2. Press the ▲▼◄ ► buttons or
ENTER button to select the
desired menu.
•
button.
If you press the SKIP ($) button, it moves to
the next chapter.
If you press the SKIP (#) button, it moves to
the beginning of the chapter. One more press
makes it move to the beginning of the previous
chapter.
✎NOTE
Depending on the disc, the menu items may
differ and this menu may not be available.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
44
Slow Motion Play/Step Motion Play
Repeat
Off
Slow Motion Play
hzZyx
3. To return to normal play, press the REPEAT
button again.
•
In pause mode, press the SEARCH ()
button.
If you press the SEARCH () button, the
playback speed is reduced to
* 1/8 * 1/4 * 1/2
To return to normal speed playback, press the
PLAY (► ) button.
4. Press the ▲▼ buttons to select Off, the
press the ENTER button.
✎NOTE
•
Depending on the disc, the Repeat function
may not be available.
NOTE
✎
Repeat the Section
No sound is heard during slow mode.
Slow motion operates only in the forward
direction.
hzZy
REPEAT
1. During playback, press the REPEAT
Step Motion Play
button on the remote control.
2. Press the ▲▼ buttons to select
hzZyx
In pause mode, press the PAUSE ( ) button.
REPEAT A-B.
•
•
Repeat
REPEAT A-B : Off
sMark A
Each time the PAUSE ( ) button is pressed, a
new frame will be appear.
To return to normal speed playback, press the
PLAY ( ► ) button.
3. Press the ENTER button at the point where
NOTE
✎
you want repeat play to start (A).
No sound is heard during step mode.
Step motion operates only in the forward
direction.
4. Press the ENTER button at the point where
you want repeat play to stop (B).
5. To return to normal play, press the REPEAT
button again.
Repeat Playback
6. Press the ENTER button.
Repeat the Title or Chapter
NOTE
✎
If you set point (B) before 5 seconds has
lapsed, the prohibition message will appear.
hzZy
Repeat the disc title or chapter.
REPEAT
1. During playback, press the REPEAT
button on the remote control.
2. Press the ▲▼ buttons to select
Chapter or Title, then press the
ENTER button.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
45
Basic Functions
Information about the primary / secondary
mode will be also displayed if the Blu-ray Disc
has a BONUSVIEW section.
Use the ◄► button to switch between
primary and secondary audio modes.
This function depends on what audio
languages are encoded on the disc and may
not be available.
A Blu-ray Disc can contain up to 32 audio
languages and a DVD up to 8.
Using the TOOLS button
TOOLS
During playback, you can operate disc
menu by pressing the TOOLS button.
•
TOOLS Menu Screen
Tools
:
Title
1/1
4/21
00:12:06
Chapter
Playing Time
Repeat
:
Audio
Subtitle
Angle
:
:
:
1/7 ENG Multi CH
1/6 ENG
1/1
Off
0/1 Off
Some Blu-ray Discs may allow you to select
either the multi-channel LPCM or Dolby digital
audio soundtrack in English.
BONUSVIEW Video :
BONUSVIEW Audio :
Picture Setting
<Change
Select
"
Selecting the Subtitle Language
NOTE
hZx
✎
Depending on the disc, the TOOLS menu
may differ.
▪
1. During playback, press the TOOLS button.
2. Press the ▲▼ buttons to select Subtitle.
Moving to a Desired Scene Directly
3. Press the ◄► buttons to select the desired
subtitle language.
hzZy
NOTE
✎
Depending on the Blu-ray Disc / DVD, you may
be able to change the desired subtitle in the
Disc Menu.
1. During playback, press the TOOLS button.
2. Press the ▲▼ buttons to select Title,
Chapter or Playing Time.
Press the DISC MENU button.
3. Enter the desired Title, Chapter or Playing
Time using the number buttons, then press
the ENTER button.
This function depends on what subtitles are
encoded on the disc and may not be available
on all Blu-ray Discs/DVDs.
A Blu-ray Disc can contain up to 255 subtitle
languages and a DVD up to 32.
Information about the primary / secondary
mode will also be displayed if the Blu-ray Disc
has a BONUSVIEW section.
This function changes both the primary and
secondary subtitles at the same time.
The total number of subtitles is the sum of the
primary and secondary ones.
Selecting the Audio Language
hzZx
1. During playback, press the TOOLS button.
2. Press the ▲▼ buttons to select Audio.
3. Press the ◄► buttons to select the desired
audio language.
✎NOTE
The ◄► indicator will not be displayed on the
screen if the BONUSVIEW section does not
contain any BONUSVIEW audio settings.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
46
•
User : The user can adjust the sharpness
and noise reduction function respectively.
Caption Function
x
Setting the BONUSVIEW
•
•
You must have some experience with video
extraction and editing in order to use this
feature properly.
h
To use the caption function, save the caption
file (*.smi) in the same file name as that of the
DivX media f le (*.avi) within the same folder.
Example. Root Samsung_007CD1.avi
Samsung_007CD1.smi
Up to 60 alphanumeric characters or 30 East Asian
characters (2 byte characters such as Korean and
Chinese) for the file name.
The BONUSVIEW feature allows you to view
additional content (such as commentaries) in a
small screen window while the movie is playing.
This function is only available if the disc has the
bonusview feature.
•
Changing the Camera Angle
hZ
When a Blu-ray Disc/DVD contains multiple
angles of a particular scene, you can use the
ANGLE function.
Primary a audio/video
Secondary a audio/video
1. During playback, press the TOOLS button.
2. Press the ▲▼ buttons to select Angle.
1. During playback, press the TOOLS button.
3. Press the ◄► buttons to select the desired
Angle.
2. Press the ▲▼ buttons to select BONUSVIEW
Video or BONUSVIEW Audio.
3. Press the ◄► buttons to select the desired
Selecting the Picture Setting
bonusview.
hzZy
This function enables you to adjust video quality
when you are connected to a TV via HDMI.
NOTE
✎
If you switch from BONUSVIEW Video,
BONUSVIEW Audio will change automatically
in accordance with BONUSVIEW Video.
1. During playback, press the TOOLS button.
Tools
2. Press the ▲▼ buttons to select Picture
Setting, then press the ENTER button.
BONUSVIEW Video
BONUSVIEW Audio :
Picture Setting
Off
0/1 Off
3. Press the ◄► buttons to select the desired
Picture Setting, then press the ENTER
button.
<Change
Select
"
•
•
•
Dynamic : Choose this setting to increase
Sharpness.
Normal : Choose this setting for most
viewing applications.
Movie : This is the best setting for watching
movies.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
47
Basic Functions
Listening to Music
ENTER button : Plays and pauses the selected
7
8
track.
ow
Buttons on the Remote Control
used for Music Playback
STOP button : Stops a track
.
SKIP($) button : During playback, moves to
the next page in the Music List or moves to the
next track in the Playlist.
9
0
!
SKIP (
#
)button : During playback, moves to the
previous page in the Music List or moves to the
previous track in the Playlist.
If you press this button after three seconds of
playback in the Playlist, the current track will be
replayed from the beginning. But, if you press this
button within three seconds after playback starts
in the Playlist, the previous track will be played.
!
FULL SCREEN
1
2
0
9
8
NUMBER button : During the Playlist playback,
press the desired track number. The selected
track will be played.
3
4
TOOLS
INFO
5
6
7
RETURN
EXIT
TUNER
MO/ST
@
INTERNET
DSP
REPEAT buttons : Selects the play mode in the
Playlist.
1
2
3
4
5
6
SEARCH buttons : Fast Play.
(Audio CD (CD-DA) only)
PAUSE button : Pauses playback.
PLAY button : Plays the currently selected track.
▲▼ buttons : Selects a track in the Music List
or Playlist.
YELLOW(C) button : Select or deselect a track
in the music list.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
48
Playing an Audio CD (CD-DA)/MP3 Repeat an Audio CD (CD-DA)/MP3
REPEAT
1. Insert an Audio CD (CD-DA) or an MP3 Disc
1. During the Playlist playback, press
into the disc tray.
the REPEAT button.
•
For an Audio CD (CD-DA), the first track will
2. Select the desired play mode by
be played automatically.
pressing the REPEAT button repeatedly.
•
For an MP3 disc, press the ◄► buttons to
select Music, then press the ENTER
button.
Tracks on a disc are played
in the order in which they
were recorded on the disc.
Audio CD
(CD-DA)/MP3
Off
Audio CD (CD-DA)/MP3 Screen Elements
Audio CD
(CD-DA)
(
(
(
) Track
) One
) All
Current track is repeated.
Current track is repeated.
All tracks are repeated.
The random option plays a
1
2
3
MP3
Playlist
1/12
Audio CD
(CD-DA)/MP3
TRACK 001
TRACK 001
TRACK 002
TRACK 003
TRACK 004
TRACK 005
TRACK 006
05:57
04:27
04:07
03:41
03:17
03:35
Audio CD
(
)Shuffle
(CD-DA)/MP3 disc's track in random order.
7
6
+
00:08 / 05:57
Playlist
s
Pause
Tools rReturn
1. Insert an Audio CD (CD-DA) or an MP3 Disc
into the disc tray.
•
•
For an Audio CD (CD-DA), the first track will
be played automatically.
For an MP3 disc, press the ◄► buttons to
select Music, then press the ENTER
button.
5
4
Displays the music information.
Displays the playlist.
1
2
3
4
5
6
7
2. To move to the Music List, press the STOP ()
or RETURN button.
Shows the current track/total tracks.
Displays buttons available.
The Music List screen is displayed.
3. Press the ▲▼◄► buttons to move to the
desired track, then press the YELLOW(C) button
to check desired tracks.
Shows the current play time/total play time.
Displays the current playback status.
Displays the repeated playback status.
Repeat this procedure to select additional tracks.
3 files selected 1/2 Page
Music TRACK 003
TRACK 001
00:05:57
TRACK 002
00:04:27
TRACK 003
00:04:07
TRACK 004
00:03:41
2. Press the ▲▼ buttons to select the track
you want to play, and then press the ENTER
button.
TRACK 005
00:03:17
TRACK 006
00:03:35
TRACK 007
00:03:47
TRACK 008
00:03:49
TRACK 009
00:03:53
TRACK 010
00:03:45
Jump page rReturn
CDDA
c Select
Download from Www.Somanuals.com. All Manuals Search And Download.
English
49
Basic Functions
4. If there is an undesired track in the playlist,
press the YELLOW(C) button again.
The selected track will be deleted.
Sound Mode
DSP(Digital Signal Processor) Function
5. Press the ENTER button to play the selected
tracks.
This will regulate and stabilize the volume level
against a drastic volume change when changing
channels or during a scene transition.
The selected track will automatically play.
1/1
Playlist
DSP
TRACK 001
TRACK 001
TRACK 002
TRACK 003
05:57
04:27
04:07
Press the DSP button.
SMART SOUND ¨ MP3 ENHANCER ¨
POWER BASS ¨ DSP MODE OFF
+
00:08 / 05:57
• SMART SOUND : This will regulate and
stabilize the volume level against a drastic
volume change when changing channels or
during a scene transition.
s
Pause
Tools rReturn
• MP3 ENHANCER : This also helps enhance
your sound experience (ex. mp3 music). You
can upscale your MP3 level sound(24 kHz,
8bit) to CD level sound(44.1 kHz, 16bit).
6. To go to the Music List, press the STOP ()
or RETURN button.
7. To go to the Playlist, press the ENTER
button.
• POWER BASS : This function stresses low
tones providing thudding sound effects.
NOTE
✎
You can create a playlist with up to 99 tracks
on Audio CD (CD-DA).
SFE(Sound Field Effect) MODE
You can set the SFE mode best suited for the
type of music you are listening to.
SFE MODE
Press the SFE MODE button.
Provides a clear vocal as if
HALL1
listening in a concert hall.
Provides also a clear vocal as if
listening in a concert hall but, less
powerful than HALL1.
HALL2
JAZZ
Recommended setting for Jazz.
Gives the feel of being in a grand
church.
CHURCH
ROCK
Recommended setting for Rock.
Select this for normal listening.
SFE OFF
Download from Www.Somanuals.com. All Manuals Search And Download.
English
50
Dolby Pro Logic II Mode
Using the TOOLS button
You can select the desired Dolby Pro
TOOLS
During the slide show playback, you
can use various function by pressing
the TOOLS button.
Logic II audio mode.
Press the
PL II button.
When listening to music, you can experience
sound effects as if you are listening to the
actual performance.
Tools
MUSIC
MOVIE
Stop Slide Show
Slide Show Speed :
Background Music
Zoom
Normal
Adds realism to the movie soundtrack.
Rotate
Information
You will experience a realistic multi-channel
effect, as if using six speakers, while using
just the front left and right speakers.
PROLOG
>Move
"
Enter
'
Return
MATRIX
STEREO
You will hear multi channel surround sound.
Select this to listen to sound from the front left
and right speakers and the subwoofer only.
•
•
•
•
•
Start Slide Show : Select this if you want to
start the slide show.
Slide Show Speed : Select this if you want to
adjust the Slide Show speed.
Background Music : Select this if you want to
listen to music while viewing a picture.
Zoom : Select this if you want to enlarge the
current picture. (Enlarged up to 4 times)
Rotate : Select this if you to rotate the picture.
(This will rotate the picture either clockwise or
counter clockwise.)
✎NOTE
When selecting Dolby Pro Logic II mode,
connect your external device to the AUDIO
INPUT jacks (L and R) on the product. If you
connect to only one of the inputs (L or R), you
cannot listen to surround sound.
This mode is available only with 2 channel audio.
Playing back a Picture
•
Information : Shows the picture information
including the name and size, etc.
G
NOTE
✎
Playing a JPEG Disc
To enable the Background Music function,
both music and MP3 files must be contained in
the same folder. However, the sound quality
can be affected by the bit rate of the MP3 file,
the size of the photo and the encoding
method.
1. Insert a JPEG disc into the disc tray.
2. Press the ◄► buttons to select the Photos,
and then press the ENTER button.
3. Press the ▲▼◄► buttons to select the
folder you want to play, and then press the
ENTER button.
4. Press the ▲▼◄► buttons to select the
photo you want to play, and then press the
ENTER button.
NOTE
✎
You can't enlarge the subtitle and PG graphic
in the full screen mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
51
Basic Functions
NOTE
✎
Playing back a USB Storage
You must remove the USB storage device
safely (by performing the “Safe to Remove
Hardware” function) in order to prevent a
possible damage to the USB memory. Press
the MENU button to move to the main screen,
and select the YELLOW(C) button and press the
ENTER button.
When the Audio-CD (CD-DA), MP3 and JPEG
files are in stop mode, you can't see full screen
by pressing the FULL SCREEN button on the
remote control.
If you insert the disc when playing USB storage
device, the device mode is changed to “DVD
or CD” automatically.
To listen to your music files with 5.1 channel sound,
you must set the Dolby Pro Logic II mode to Matrix.
(See page 51)
F
You can use the USB connection to play multimedia
files (MP3, JPEG, DivX, etc) downloaded from the
USB storage device.
1. Move to the home menu.
2. In Stop mode, connect the USB storage device
to the USB port on the front panel of the product.
The message “Do you want to access the
device?” will be displayed.
3. Press the ◄► button to select Yes, then
press the ENTER button.
4. Press the RED(A) button.
TV service
Please activate Intern
e
t
@
to enjoy a variety of Internet Services.
Listening to Radio
CD
Using buttons on the Remote Control
USB
USB a Change Device
c Safely Remove USB d View Devices
Enter
"
1. Press the FUNCTION button to select FM.
2. Tune in to the desired station.
5. Press the ▲▼ buttons to select the USB,
then press the ENTER button.
6. Press the ◄► buttons to select the desired Videos,
Music or Photos, then press the ENTER button.
4-1. Press the BLUE(D) button.
•
Automatic Tuning 1 : When the # $ button
is pressed, a preset broadcast station is selected.
•
Automatic Tuning 2 : Press and hold the
TUNING/CH (
) button to automatically
search for active broadcasting stations.
•
Manual Tuning : Press the TUNING/CH
Please activate Internet@TV service
to enjoy a variety of Internet Services.
(
) button to increase or decrease the
frequency incrementally.
USB
Using buttons on the product
1. Press the FUNCTION (
) button to select FM.
2. Select a broadcast station.
USB
d Home
Enter
"
•
Automatic Tuning 1 : Press the STOP ( I )
button to select PRESET and then press the
# $ button to select the preset station.
5-1. Press the ◄► buttons to select the USB,
then press the ENTER button.
•
Automatic Tuning 2 : Press the STOP ( I )
button to select MANUAL and then press and
hold the # $ button to automatically
search the band.
6-1. Press the ▲▼ buttons to select the desired
Videos, Music or Photos, then press the
ENTER button.
7. For playing back Video, Music or Photos
•
Manual Tuning : Press the
button to
STOP ( I )
and then press the # $
button to tune in to a lower or higher frequency.
files, see pages 43~51.
select MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
English
52
Setting Mono/Stereo
Using an iPod
MO/ST
D
You can enjoy music, video files from an iPod
through the product.
Press the MO/ST button.
•
Each time the button is pressed, the
sound switches between STEREO
and MONO.
FM ANT
DIDITAL
WIRELESS
H
D
MI
AUDIO IN
iPod
ANCE
:
3
•
In a poor reception area, select MONO for a
clear, interference-free broadcast.
iPod
Presetting Stations
Example : Presetting FM 89.10 into memory
1. Press the FUNCTION button to select FM.
TUNING/CH
2. Press the
(
)
button to select
<89.10>.
TUNER
3. Press the TUNER MEMORY button.
NUMBER flashes on the display.
MEMORY
Listening to Music
C
•
You can play music files stored in the iPod player by
connecting it to the product.
4. Press the # $ button to select
preset number.
•
You can select between 1 and 15
presets.
Please activate Internet@TV service
to enjoy a variety of Internet Services.
5. Press the TUNER MEMORY button again.
•
Press the TUNER MEMORY button before
NUMBER disappears from the display.
•
NUMBER disappears from the display and
the station is stored in memory.
No disc
MEMU
iPod
6. To preset another station, repeat steps 2 to 5.
No Disc
a Change Device
d View Devices s Enter
•
To tune in to a preset station, press the #
$ button on the remote control to select a
channel.
1. Connect the iPod dock connector to the iPod
Jack on the rear panel of the product.
2. Place the iPod in the supplied iPod Dock.
•
Your iPod is automatically turned on.
•
“iPod” message appears on the TV screen.
3. Press the RED(A) button.
4. Press the ▲▼ buttons to select iPod, then press
the ENTER button.
5. Press the ◄► buttons to select Music, then
press the ENTER button.
6. Select the music file to play.
-
You can use the remote control or product to
control simple playback functions such as the
PLAY, PAUSE, STOP, #/ $, / and
REPEAT buttons. See page 16.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
53
Basic Functions
✎NOTE
Watching a Movie
You can play video files stored in the iPod player
by connecting it to the product.
Adjust the volume to a moderate level before
you connect your iPod and product.
When the product is powered on and you
connect an iPod, the product will charge your
iPod's battery.
1. Connect the iPod dock connector to the
iPod Jack on the rear panel of the product.
Make sure to connect the dock connector so
that the label “SAMSUNG” faces upward.
“Made for iPod” means that an electronic accessory
has been designed to connect specifically to the
iPod and has been certified by the developer to meet
Apple performance standards.
“Works with iPhone” means that an electronic
accessory has been designed to connect specifically
to an iPhone and has been certified by the developer
2. In the iPod screen, move to Settings >
Videos, then set the TV Out option and the
TV signal.
3. Place the iPod in the supplied iPod Dock.
•
“iPod” message appears on the TV
screen.
4. Press the RED(A) button.
5. Press the ▲▼ buttons to select iPod, then press
to meet Apple performance standards.
the ENTER button.
iPod Music categories
6. Press the ◄► buttons to select Videos, then
press the ENTER button.
7. Select the video file to play.
File information including the artist name, album
name, music title and genre will be displayed
according to the ID3 Tag information on the
appropriate music file.
-
You can use the remote control or the
product to control simple playback functions
such as the PLAY, PAUSE, STOP,
and /buttons. (See page 16.)
#
/$
Plays a recently played file or
Now
Playing
moves to the playback screen of
the current file.
iPod models that can be used with
this product
Artist
To play by artist.
To play in numeric or alphabetical
order
Songs
iPod nano
3rd generation
(video)
iPod touch
1st generation
iPod
5th generation
(video)
iPod touch
2nd generation
iPod nano
4th generation
(video)
Playlist
Album
To play by Playlist.
To play by album.
To play by genre.
To play by composer.
iPhone 3G
iPod classic
iPhone
Generic
Composers
✎NOTE
You must have the VIDEO output (Composite)
connected to your TV to view iPod video (See page 23).
If you want to iPod video via VIDEO output, set
Anynet+(HDMI-CEC) to off.
No other screen than the playback one will appear on
the TV screen. Check other screens on the iPod player.
If the connected iPod does not support video playback,
the “Cannot play video files saved on this iPod”
message appears when you select the Video menu.
Apple is not responsible for the operation of this device
or its compliance with safety and regulatory standards.
✎NOTE
The category list may differ, depending on the
iPod model.
What is an ID3 Tag?
This is what is attached to an MP3 to carry
information relevant to the file such as the title,
artist, album, year, genre and a comment field.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
54
Network Services
You can enjoy various network services such as
Internet@TV or BD-LIVE by connecting the
product to the network system.
4. When you have agreed on the service
agreement, the Internet@TV service will start
being updated. It takes several minutes.
When the update is completed, you will see
the Internet@TV menu screen.
Check the following instructions before using
any network service.
1. Connect the product to the network.
Internet@TV at a Glance
(see pages 25~26)
1
2
3
2. Configure the network settings.
(see pages 37~40)
Recommended
Contents
1
Contents
2
2
Contents
Contents
3
3
Contents
4
Using Internet@TV
My Applications
by Date 1/3
Contents
1
Contents
Connect this product to the network to download
various chargeable or free-of-charge applications.
Internet@TV brings useful and entertaining
contents and services directly from the web to
your product.
And enjoy the applications such as news,
weather forecast, stock market, games, movies
and music.
Samsung AppS Settings
aLogin bMark as Favorite dSort by
Return
'
6
5
4
Commercial : Displays Internet@TV Guide,
product introduction and new application
introduction.
@
INTERNET
1
You can also operate this function
by pressing the INTERNET@ button
on the remote control.
Recommended : Displays recommended
contents managed by Samsung.
2
3
My Application : Displays your personal gallery
which can be added and deleted by you.
Getting Started with Internet@TV
Navigation Help : Displays remote control
1. Move to the home menu.
buttons available.
•
•
RED(A) : To log in to to Internet@TV.
BLUE(B) : To mark the application as a
favorite.
TV service
Please activate Intern
e
t
@
4
to enjoy a variety of Internet Services.
•
•
GREEN(D) : To sort the applications.
Return : To return to the previous
menu.
Settings : You can set the system setup and
5
6
create accounts, etc.
No Disc
a Change Device
d View Devices
Enter
"
Samsung AppS : You can download various
chargeable or free-of-charge application services.
2. Press the ◄► buttons to select Internet@
TV and press the ENTER button.
3. In the start screen of the Internet@TV service,
you will see the service agreement screen.
You should agree to the service terms and
conditions before you can use the Internet@
TV service.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
55
Network Services
13. Press the ENTER button.
Using the Keypad
14. The map and address appear on the screen.
Pressing the FULL SCREEN button on the
remote while you are using the Screen Keypad
enables you to change the text fields to lower
case, upper case, numbers and icons.
You can use this Screen Keypad in a several
Internet@TV applications.
NOTE
✎
Samsung Electronics shall take no legal
responsibility for any interruption of the
Internet@TV service caused by the service
provider for any reasons.
The Internet@TV service is to download and
process data via the Internet so that you can
enjoy the contents on the TV screen.
If the Internet connection is unstable, the
service may be delayed or interrupted.
Furthermore, the product may be turned off
automatically.
abc
jkl
def
mno
wxyz
1
4
7
2
5
8
0
3
6
9
ghi
pqrs
tuv
Input Mode
Delete
a
A
1
If this is the case, check the Internet
connection and try again.
For example, here is how to search an address in
Google Maps:
The application service may be provided in
English only and the contents available may
vary, depending on the area.
1. Press the ENTER button on the remote at
the Google Maps icon at the Internet@TV.
For more information about the Internet@TV
service, visit the web site of the applicable
service provider.
2. Press the GREEN(B) button to use the
SEARCH function.
3. Press the ◄► buttons to move to the
The provided services are subject to change,
depending on the Internet@TV service
provider.
"Search or address" window.
4. Press the ENTER button to use Search or
address function.
The Internet@TV service contents may differ
according to the firmware version.
5. For example, suppose that you want to input
“105 Challenger Rd., Ridgefield Park NJ’.
A chargeable DivX contents with copy
protection can only be played using HDMI
cable.
If connected with component or video cable,
the video signal can not output or the popup
message “cannot play current file” will be
displayed.
6. Press the FULL SCREEN button on the
remote twice to change the input mode from
lower case to numbers.
7. Press ‘1’, ‘0’, ‘5’.
8. Press the YELLOW(C) button on the remote
to input a blank space.
9. Press the FULL SCREEN button on the
remote 3 times to change the input mode
from numbers to upper case.
10. Press ‘2’ button on the remote 3 times to
input C.
11. Press the FULL SCREEN button on the
remote 3 times to change the input mode
from upper case to lower case.
12. Press buttons on the remote to input the rest
of ‘Challenger Rd., Ridgefield Park NJ’.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
56
Account Login
System Setup
Reset
For a more enjoyable application experience,
register and log in to your account.
To do this, you must create an account first. (For
instructions on creating an account, refer to
Internet@TV ID on this page)
Resets Internet@TV settings to factory default
settings.
NOTE
✎
1. Press the ▲▼◄► buttons to select the
desired application and press the RED(A)
button.
If you forgot your password, press the STOP
() button on the front panel of the product for
more than 5 seconds with no disc inserted.
Login
Internet@TV ID
You can use this menu when creating, deleting
the account.
You can control your account including contents
site’s account information.
User Account :
Password :
adgim
Account is only for Internet@TV.
a Create
[0~9] Enter PIN
'
Cancel
Create
Create an account and link it with desired service
applications.
2. Enter the user account and password.
Settings
NOTE
✎
Account will be made less than 10 and
Maximum number of characters is 10.
Create IDs and configure Internet@TV settings
from this screen.
Settings
Manager
. System setup
. Internet@TV ID
. Service Manager
. Properties
Change the Service Lock password
Reset
•
•
•
Service Site : Register login information for
service sites.
Change Password : Change account
password.
Delete : Delete the account.
'
Cancel
Download from Www.Somanuals.com. All Manuals Search And Download.
English
57
Network Services
Using the color buttons with the Samsung
Apps
Service Manager
Delete and lock applications installed to Internet@
TV.
•
•
•
RED(A) (Login) : To log in to the internet
service.
GREEN(B) (Thumbnail View) : To change the
view mode.
BLUE(D) (Sort By) : To sort the applications
by Featured, Most Downloaded, Most Recent
or Name.
Lock
Lock the application. Accessing a locked
application requires the password.
Delete
Delete the application.
Internet@TV Services Available
•
YouTube : You can view video streamed by
YouTube.
Properties
Display information about Internet@TV. Use the
Check the speed of your internet connection
option to test your network connection.
NOTE
✎
The available Internet contents service may be
added or deleted.
Samsung AppS
Various applications are available from here,
organized into different categories. Some
applications have a download fee.
Samsung AppS
Video
1/1
Featured
Most downloaded
Most recent
Name
What's New!
Video
YouTube
Free
Sports
Lifestyle
TV store Test User002
Games
Infomation
Other
My Applications
Help
a Login b Thumbnail View d Sort By
'
Return
My Application
Displays the application list.
Help
If you questions about Internet@TV, check this
section first. If none of the tips apply, please visit
the help website.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
58
BD-LIVE™
Using the AllShare Function
Once the product is connected to the network,
you can enjoy various movie-related service
contents using a BD-LIVE compliant disc.
1. Check the size of the remaining memory.
The memory device must have at least 1GB
of free space to accommodate the BD-LIVE
services.
AllShare enables you to play music, video and
photo files in your PC using the product.
To use AllShare, you must connect the product to
your PC via the network (See pages 25~26) and
install the SAMSUNG PC Share Manager on the PC.
com.
2. Insert a Blu-ray disc that supports BD-LIVE.
2. Download the SAMSUNG PC Share
Manager and install it on the PC.
3. Select an item from various BD-LIVE service
contents provided by the disc manufacturer.
3. When the installation is completed, you will
see the SAMSUNG PC Share Manager icon
on your desktop. Double-click the icon to
launch the application.
NOTE
✎
The way you use BD-LIVE and the provided
contents may differ, depending on the disc
manufacturer.
Application Program at a Glance
6
1
Software Upgrade Notification
SAMSUNG PC Share Manager
File Share Server Help
In network connection, the product will notice you of
any new software version with a popup message.
1. Turn on the product.
Server : PC Share Manager
2 3 4 5
My Computer
Shared Folder
Folder
Folder 1
C: Document and settings Admin
Full Path
C: Document and settin..
Name
Folder 1
Size
Kind
File
2. From the Software Upgrade menu, set Auto
Upgrade Notification to On. (See page 42)
If there is a new software version available,
the product will notice you with a popup
message.
Folder 2
Folder 3
File
File
3. To upgrade the firmware, select Yes.
It will turn off automatically before restarting.
(Never turn it on manually.)
4. The update progress popup will appear.
When the update is completed, it will turn
back off automatically.
8
7
Menu Bar
1
2
Share Folder Enabled icon : Use this if you
want to select a folder in your PC to share.
Share Folder Disabled icon : Use this if you
want to set folder sharing off.
5. Press the POWER button to turn on the
3
4
product.
Refresh icon : Use this if you want to refresh
list of folders and files in My Computer.
NOTE
✎
Update icon : Select a folder to share and
don’t forget to press this button.
The updated state will be applied to the server.
Update will be completed when the product
turns off after restarting. Press the POWER
button to turn on the updated product for your
use.
5
Server : Displays the name of the sharing
server.
6
7
8
Never turn off or on the product manually
during the update process.
Samsung Electronics shall take no legal
responsibility for product malfunction caused by
unstable of internet connection or consumer
negligence during software upgrade.
Shared Folder : Displays a list of the shared
folders.
My Computer : Displays a list of the folders
and files in the PC.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
59
Network Services
4. Select a folder to share from the My
AllShare does not support the following
functions.
computer pane, and click the Share Folder
Enabled icon
).
- The Background Music and Background
Music Setting functions.
(To remove a shared folder : Select a folder
to remove from the shared folders, and click
- Sorting files by preference in the Photo,
Music, and Movie folders.
the Share Folder Disabled icon
).)
5. To apply the updated sharing state to the
- The Change Group function.
- The Safe Remove function.
server, click the Set Change State icon
).
6. To enable the product to locate a PC server,
click Share from the menu bar.
The Sorting method may differ depending on
the sever function.
Click Set Device Policy and click Accept.
The search and skip operation may differ
depending on the sever function.
SAMSUNG PC Share Manager
File Share Server Help
Server : PC Share Manager
If you press the STOP () button during video
playback, stop position will be memorized and
it will be memorized only end user's operation.
But stop position will not be memorized
depending on the sever function.
Set Device Policy
My Co
Delete
Item
Selected
C:
IP Device
State
Set State
settin..
Nam
Accept
XXX.XXX.X.XX SAMSUNG Blu-ray Disc Player
Deny
F
F
F
OK
Cancel
During video playback, play time will not
display.
To use AllShare function, please locate both
this product and PC in same subnet.
7. Click the Set Change State icon
)
and
move to the home menu on the product.
8. To select a device, use the RED(A) or
BLUE(D) button to select a file to play.
(For playing back Video, Music or Photos files,
see pages 43~51.)
TV service
Please activate Intern
e
t
@
to enjoy a variety of Internet Services.
No Disc
a Change Device
d View Devices
Enter
"
NOTE
✎
Depending on te performance of the external
modem or router, HD video may not play
properly.
If your system uses a firewall, the product may
not locate your PC on the TV screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
60
Other information
Troubleshooting
Refer to the chart below when this product does not function properly. If the problem you are
experiencing is not listed below or if the instruction below does not help, turn off the product,
disconnect the power cord, and contact Samsung Electronics at 1-800-SAMSUNG.
Symptom
Check/Remedy
I cannot eject the disc.
• Is the power cord plugged securely into the outlet?
• Turn off the power and then turn it back on.
The iPod fails to connect.
Playback does not start.
• Check the condition of the iPod connector and Dock.
• Keep the iPod S/W version up to date.
• Check the region number of the BD/DVD.
BD/DVD discs purchased from abroad may not be playable.
• CD-ROMs and DVD-ROMs cannot be played on this Product.
• Make sure that the rating level is correct.
Playback does not start
immediately when the
Play/Pause button is pressed.
• Are you using a deformed disc or a disc with scratches on the surface?
• Wipe the disc clean.
Sound is not produced.
•
•
No sound is heard during fast playback, slow playback, and step motion playback.
Are the speakers connected properly? Is the speaker setup correctly customized?
• Is the disc severely damaged?
Sound can be heard only from a
few speakers and not all 6.
• On certain BD/DVD discs, sound is output from the front speakers only.
• Check if the speakers are connected properly.
• Adjust the volume.
• When listening to a CD, radio or TV, sound is output to the front speakers only.
Select "PRO LOGIC II" by pressing
control to use all six speakers.
PL II (Dolby Pro Logic II) on the remote
Dolby Digital 5.1 CH Surround
Sound is not produced.
•
Is there "Dolby Digital 5.1 CH" mark on the disc? Dolby Digital 5.1 CH Surround Sound is
produced only if the disc is recorded with 5.1 channel sound.
• Is the audio language correctly set to Dolby Digital 5.1-CH in the information
display?
The remote control does not work.
•
Is the remote control being operated within its operation range of angle and distance?
• Are the batteries drained?
•
Have you selected the mode(TV/BD) functions of the remote control (TV or BD) correctly?
• Disc is rotating but no
picture is produced.
• Is the TV power on?
• Are the video cables connected properly?
• Is the disc dirty or damaged?
• Picture quality is poor and
picture is shaking.
• A poorly manufactured disc may not be playable.
Audio language and subtitles do
not work.
•
Audio language and subtitles will not work if the disc does not contain them.
Menu screen does not appear
even when the menu function is
selected.
• Are you using a disc that does not contain menus?
Download from Www.Somanuals.com. All Manuals Search And Download.
English
61
Other information
Symptom
Check/Remedy
Aspect ratio cannot be changed.
• You can play 16:9 BD/DVDs in 16:9 Wide mode, 4:3 Letter Box mode, or 4:3
Pan - Scan mode, but 4:3 BD/DVDs can be seen in 4:3 ratio only. Refer to the
Blu-ray Disc jacket and then select the appropriate function.
• The product is not working.
(Example: The power goes out
or a strange noise is heard.)
• Turn off the power, and press and hold the STOP ( I ) button on the product
for longer than 5 seconds with no disc inserted.
- Using the RESET function will erase all stored settings.
Do not use this unless necessary.
•
The Product is not working
normally.
The rating level password has
been forgotten.
• With no disc in the product, press and hold the product's STOP ( I ) button for
longer than 5 seconds. INIT appears on the display and all settings will return
to the default values.
And then press the POWER button.
- Using the RESET function will erase all stored settings.
Do not use this unless necessary.
Can't receive radio broadcasts.
• Is the antenna connected properly?
• If the antenna's input signal is weak, install an external FM antenna in an area
with good reception.
While listening to TV audio
through the Product, no sound is
heard.
•
If the OPEN/CLOSE ( ) button is pressed while listening to TV audio using the
D.IN or AUX functions, the BD/DVD functions are turned on and the TV audio is
muted.
"Not Available" appears on
screen.
• The features or action cannot be completed at this time because:
1. The BD/DVD’s software restricts it.
2. The BD/DVD’s software doesn’t support the feature (e.g., angles)
3. The feature is not available at the moment.
4. You’ve requested a title or chapter number or search time that is out of range.
If the HDMI output is set to a
resolution your TV cannot support
(for example, 1080p), you may not
see a picture on your TV.
• Press and hold the STOP ( I ) button on front panel for more than 5 seconds
with no disc inserted. All settings will revert to the factory settings.
No HDMI output.
• Check the connection between the TV and the HDMI jack of the Product.
• Check if your TV supports 480p/720p/1080i/1080p HDMI input resolution.
Abnormal HDMI output screen.
• If random noise appears on the screen, it means that TV does not support
HDCP (High-bandwidth Digital Content Protection).
If the HDMI output is set to a resolution
your TV cannot support (for example,
1080p), you may not see a picture on
your TV.
• Press and hold the STOP () button on front panel for more than 5 seconds
with no disc inserted. All settings will revert to the factory settings.
• When the factory default settings are restored, all the user data stored in the
BD data will be deleted.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
62
Symptom
Check/Remedy
PC Share Manager function
I can see folders shared through
the PC Share Manager, but I
cannot see the files.
• Since it shows only files corresponding to the Image, Music, and Movie
categories, files that do not correspond to these categories may not be
displayed.
AllShare function
Video is played intermittently.
• Check if the network is stable.
• Check if the network cable is properly connected and if the network is not
overloaded.
• Wireless connection between the server and the product is unstable.
Check the connection.
AllShare connection between TV
and PC is unstable.
•
IP address under the same subnetwork should be unique, otherwise IP collision
can results in such a phenomenon.
•
Check if you have a firewall enabled.
If so, disable the firewall function.
BD-LIVE
I cannot connect to the BD-LIVE
server.
• Check whether the network connection is successful or not by using Network
Test menu. (See page 40)
• Check whether the USB memory device is connected with product or not.
• The memory device must have at least 1GB of free space to accommodate the
BD-LIVE service.
You can check the available size in BD Data Management. (See page 35)
• Please check whether the BD-LIVE Internet Connection menu is set to
Allow(All).
• If all above fails, contact the contents provider or update the latest firmware.
When using the BD-LIVE service,
an error occurs.
•
The memory device must have at least 1GB of free space to accommodate the
BD-LIVE service.
You can check the available size in BD Data Management. (See page 35)
NOTE
✎
When the factory default settings are restored, all the user data stored in the BD data will be deleted.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
63
Other information
Index
A
D
P
Accessories
AllShare
13
59
47
35
32
46
35
Digital Output
Disc menu
Display
34
43
29
36
36
51
50
35
Parental Rating
Playlist
41
49
44
41
31
Angle
Popup menu
Anynet+(HDMI-CEC)
Audio
Audio Language
AV Sync
DivX(R) Deactivation
DivX(R) Registration
Dolby Pro Logic ll Mode
DSP
Power On/Off Sound
Progressive Mode
R
Region code
Remote Control
Remote control sensor
Repeat
10
16
14
Dynamic Range Control
B
E
Background
BD-Live
BD-LIVE Internet Connection 40
41
59
Energy Saving
EQ Optimizer
41
33
45, 49
29
Resolution
BD Data Management
BD Wise
35
29
F
S
Front Display
41
41
Search
Security
Setting the Menu
Setup
SFE
Skip
44
41
28
27
50
44
16
45
42
32
45
31
46
42
35
Before Starting (Initial Setting) 27
BONUSVIEW
47
G
C
General
Change Password
Clock
Connections
Speaker
Wireless receiver module 20
TV
HDMI
Component
Composite
Set-Top Box
OPTICAL
AUX
Network
LAN Cable
Wireless Network
FM Antenna
Contact Samsung
41
36
18
18
H
HDMI Audio
HDMI Deep Color
HDMI Format
33
31
31
SLEEP(timer)
Slow motion
Software Upgrade
Speaker Setting
Step motion
Still Mode
Subtitle Language
Support
22
22
23
23
24
24
24
25
25
26
26
42
I
Initial Setting
Internet@TV
Internet@TV Screen Size
iPod
35
55
35
53
System
L
T
Language
40
Title menu
Title list
TV Aspect
TV Screen Saver
44
44
29
28
M
Mono/Stereo
Movie Frame (24 Fs)
Musical Room Calibration 33
MUTE
53
31
U
16
USB Storage
52
51
N
Z
Network Setup
Network Settings
Network Status
37
37
40
Zoom
Download from Www.Somanuals.com. All Manuals Search And Download.
English
64
Specifications
Weight
7.7 Ibs
Dimensions
16.9 (W) x 2.5 (H) x 12.8 (D) inches
+41°F to +95°F
10 % to 75 %
70 dB
General
Operating Temperature Range
Operating Humidity Range
Signal/noise ratio
Usable sensitivity
FM Tuner
10 dB
Total harmonic distortion
BD (Blu-ray Disc)
0.5 %
Reading Speed : 4.917m/sec
Reading Speed : 3.49 ~ 4.06 m/sec.
Approx. Play Time (Single Sided, Single Layer Disc) : 135 min.
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 74 min.
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 20 min.
1 channel : 1.0 Vp-p (75 Ω load)
DVD (Digital Versatile Disc)
Disc
CD : 5 inches (COMPACT DISC)
1
CD : 3 /2 inches (COMPACT DISC)
Composite Video
Component Video
HDMI
Blu-ray Disc : 480i
DVD : 480i
Y : 1.0 Vp-p (75 Ω load)
Pr : 0.70 Vp-p (75 Ω load)
Pb : 0.70 Vp-p (75 Ω load)
Blu-ray Disc : 1080i, 720p, 480p, 480i DVD : 480p, 480i
1080p, 1080i, 720p, 480p
Video Output
Video/Audio
PCM multichannel audio, Bitstream audio, PCM audio
Front speaker output
165W x 2(3
170W(3
165W x 2(3
170W(3
Ω
)
)
Center speaker output
Surround speaker output
Subwoofer speaker output
Ω)
Ω
Ω)
Analog input
Digital input
70dB
20Hz~20kHz ( 3dB)
20Hz~44kHz ( 3dB)
Amplifier
Frequency response
S/N Ratio
Channel separation
Input sensitivity
60dB
(AUX)500mV
5.1ch speaker system
Speaker system
Front
3 Ω
Surround
3 Ω
Center
3 Ω
Subwoofer
3 Ω
Impedance
Frequency range
Output sound pressure level
Rated input
140Hz~20kHz 140Hz~20kHz 140Hz~20kHz 40Hz ~ 160Hz
87dB/W/M
165W
87dB/W/M
165W
87dB/W/M
170W
88dB/W/M
170W
Speaker
Maximum input
330W
330W
340W
340W
Front : 3.54 x 51.18 x 4.69 inches (Stand base : 9.84 x 9.84 inches)
Surround : 3.54 x 5.57 x 2.7 inches
Dimensions (W x H x D)
Weights
Center : 14.17 x 2.93 x 2.7 inches
Subwoofer : 6.1 x 13.78 x 11.22 inches
Front : 7.21 Ibs, Surround : 1.28 Ibs
Center : 1.26 Ibs, Subwoofer : 8.38 Ibs
*: Nominal specification
- Samsung Electronics Co., Ltd reserves the right to change the specifications without notice.
- Weight and dimensions are approximate.
- Design and specifications are subject to change without prior notice.
- For the power supply and Power Consumption, refer to the label attached to the product.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
65
LIMITED WARRANTY TO ORIGINAL PURCHASER
Samsung Electronics Canada Inc.(SECA), warrants that this product is free from defective
material and workmanship.
SECA further warrants that if this product falls to operate properly within the specified warranty
period and the failure is due to improper workmanship or defective materials, SECA will repair
or replace the product at its option.
All warranty repairs must be performed by a SECA Authorized Service Center. (The name and
address of the location nearest you can be obtained by calling toll free: 1- 800- SAMSUNG)
LABOR
PARTS
One year (Carry- in)
One year
On carry-in models, transportation to and from the service center is the customer’s responsibility.
The original dated sales receipt must be retained by the customer and is the only acceptable
proof of purchase. It must be presented to the authorized service center at the time service is
requested.
EXCLUSIONS (WHAT IS NOT COVERED)
This warranty does not cover damage due to accident, fire, flood and/ or other acts of God; misuse,
incorrect line voltage, improper installation, improper or unauthorized repairs, commercial use or
damage that occurs in shipping. Exterior and interior finish, lamps, glass are not covered under this
warranty. Customer adjustments which are explained in the instruction manual are not covered
under the terms of this warranty. This warranty will automatically be voided for any unit found with a
missing or altered serial number. This warranty is valid only on products purchased and used in
Canada.
HEADQUARTERS
SAMSUNG ELECTRONICS CANADA INC.,
CUSTOMER SERVICE
55 STANDISH COURT MISSISSAUGA, ONTARIO L5R 4B2 CANADA
FABRIQUE EN CORÉE
1-800-SAMSUNG (1-800-7267864)
WWW.SAMSUNG.COM/CA
Download from Www.Somanuals.com. All Manuals Search And Download.
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.
Region
Country
Customer Care Center
1-800-SAMSUNG (726-7864)
01-800-SAMSUNG (726-7864)
1-800-SAMSUNG (726-7864)
0800-333-3733
0800-124-421, 4004-0000
800-SAMSUNG (726-7864)
00-1800-5077267
800-7919267
0-800-507-7267
1-800-10-7267
800-6225
1-800-299-0013
1-800-234-7267
800-7267
1-800-682-3180
1-800-751-2676
1-800-SAMSUNG (726-7864)
0-800-100-5303
Web Site
CANADA
MEXICO
North America
U.S.A
ARGENTINE
BRAZIL
CHILE
NICARAGUA
HONDURAS
COSTA RICA
ECUADOR
EL SALVADOR
GUATEMALA
JAMAICA
Latin
America
PANAMA
PUERTO RICO
REP. DOMINICA
TRINIDAD & TOBAGO
VENEZUELA
COLOMBIA
01-8000112112
BELGIUM
02 201 2418
CZECH REPUBLIC
DENMARK
FINLAND
800-SAMSUNG (800-726786)
8-SAMSUNG (7267864)
30-6227 515
FRANCE
01 4863 0000
GERMANY
HUNGARY
ITALIA
LUXEMBURG
NETHERLANDS
NORWAY
01805-SAMSUNG (726-7864 € 0,14/Min)
06-80-SAMSUNG (726-7864)
800-SAMSUNG (726-7864)
02 261 03 710
0900-SAMSUNG (0900-7267864) (€ 0,10/Min)
3-SAMSUNG (7267864)
0 801 1SAMSUNG (172678), 022-607-93-33
80820-SAMSUNG (726-7864)
0800-SAMSUNG (726-7864)
902-1-SAMSUNG (902 172 678)
0771 726 7864 (SAMSUNG)
0845 SAMSUNG (7267864)
0818 717 100
Europe
POLAND
PORTUGAL
SLOVAKIA
SPAIN
SWEDEN
U.K
EIRE
AUSTRIA
SWITZERLAND
RUSSIA
0810-SAMSUNG (7267864, € 0.07/min)
0848-SAMSUNG (7267864, CHF 0.08/min)
8-800-555-55-55
KAZAKHSTAN
UZBEKISTAN
KYRGYZSTAN
TADJIKISTAN
UKRAINE
BELARUS
MOLDOVA
LITHUANIA
LATVIA
8-10-800-500-55-500
8-10-800-500-55-500
00-800-500-55-500
8-10-800-500-55-500
8-800-502-0000
810-800-500-55-500
00-800-500-55-500
8-800-77777
8000-7267
800-7267
1300 362 603
0800 SAMSUNG (0800 726 786)
400-810-5858, 010-6475 1880
3698-4698
3030 8282, 1800 110011, 1800 3000 8282
0800-112-8888
CIS
ESTONIA
AUSTRALIA
NEW ZEALAND
CHINA
HONG KONG
INDIA
INDONESIA
JAPAN
MALAYSIA
0120-327-527
1800-88-9999
1-800-10-SAMSUNG (726-7864), 1-800-3-
SAMSUNG (726-7864),
1-800-8-SAMSUNG (726-7864), 02-5805777
Asia Pacific
PHILIPPINES
SINGAPORE
THAILAND
TAIWAN
VIETNAM
TURKEY
1800-SAMSUNG (726-7864)
1800-29-3232, 02-689-3232
0800-329-999
1 800 588 889
444 77 11
Middle
East &
Africa
SOUTH AFRICA
U.A.E
0860-SAMSUNG (726-7864 )
800-SAMSUNG (726-7864), 8000-4726
Download from Www.Somanuals.com. All Manuals Search And Download.
Code No. AH68-02256G
Download from Www.Somanuals.com. All Manuals Search And Download.
|