DIGITAL VIDEO RECORDER
SHR-1040/SHR-1040K User’s Manual
English
Français
Spanish
Download from Www.Somanuals.com. All Manuals Search And Download.
Before we start
This User’s Manual describes the basic usage of SHR-1040.
This Manual contains all the matters necessary for using SHR-1040 such as brief
instruction, part name, function, connecting other equipment, and menu setup of
SHR-1040.
-
-
-
SEC retains the copyright on this User’s Manual.
This User’s Manual cannot be copied without SEC’s prior written approval.
We are not liable for any or all losses to the product incurred by your use of
non-standard product or violation of User’s Manual.
-
-
If you want to open the system case to touch the inside, please consult with an
expert who works for the shop where you bought the product.
You may download open source codes from the following website.
(See CCTV Part of http://www.sec.co.kr)
WARNING
[Battery]
As wrong exchange of the battery in SHR-1040 may cause explosion, you shall use
the certified battery for SHR-1040.
The battery specification is as follows.
-Normal Voltage : 3V
-Normal Capacity : 220mAh
-Continuous Standard Load : 0.2mA
-Operating Temperature : -22˚F ~ +140˚F
Standards Approvals
Note : This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equip-
ment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance whit the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
iii
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
ii
Safety Regulations
iii
Before we start
Standards Approvals
1
Chapter 1. Overview
1. Introduction
1-1
1-2
1-3
1-6
2. Features
3. Part Names and Functions
4. Remote Controller
2
Chapter 2. Installation
1. Installation Environment Setup
2. Checking Product & Accessory
3. HDD Addtion
2-1
2-2
2-3
3
Chapter 3. DIY Carmera
1. Standard Camera
3-1
3-5
2. Nightvision Camera
4
Chapter 4. Connecting with Other device
1. Connecting the Video, Audio, and Monitor
2. Connecting the Alarm Input/Output
4-1
4-2
5
Chapter 5. Basic Operation
1. System Operation
2. Live Screen Mode
3. Key Functions
5-1
5-2
5-3
5-3
5-3
5-4
5-4
5-5
5-5
3.1. Channel Key & Mode Key
3.2. Pip Key
3.3. Zoom Key
3.4. Freeze Key
3.5. Sequence Key
3.6. Alarm Key
iv
English
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Chapter 6. Menu Setup
1. Main Setup Menu
2. Clock/Display Setup
3. Record Mode Setup
4. Title Setup
6-1
6-2
6-3
6-4
6-5
6-6
6-7
6-9
6-10
6-14
5. Dwell Time Setup
6. Alarm Setup
7. Event Record Mode Setup
8. Timer Record Setup
9. System Setup
10. System Information
7
Chapter 7. Recording
1. Basic Recording
2. Timer Recording
3. Motion Recording
4. Alarm Recording
5. Stop Recording
7-1
7-1
7-2
7-2
7-3
8
Chapter 8. Search & Playback
1. Search Menu
8-1
8-2
8-2
8-3
8-3
8-4
8-4
2. Date Time Search
3. Record Event Search
4. Alarm Event Search
5. Loss Event List
6. Power Event List
7. Basic Playback
9
Chapter 9. Appendix
1. Product Specification
2. Recommended HDD List
3 .Outline Drawing
9-1
9-4
9-5
v
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1. Overview
1
English
Download from Www.Somanuals.com. All Manuals Search And Download.
SHR-1040/1040K USER’S MANUAL
Introduction
1
The SHR-1040 digital video recorder is a digital video recorder that records and plays back
video and audio input from four cameras. It records and plays back each channel of video data
in MPEG4 format, and audio data in installed HDD format, by using the G-723 compression
standard.
G
DVR is a digital device that stores video and audio data by using a hard disk drive, unlike a
video cassette recorder using video tapes. DVR enables users to easily play back and
search stored data, and edit and send data which are stored in digital signal format.
Users can compress, store and send moving images, and search listings on an hourly or
daily, camera unit and event basis by using this DVR with standard video and data com-
pression technology.
1-1
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
2
I Adjusts recorded data in three steps.
- HIGH, NORMAL, LOW
I Adjusts the number of record fields per second.
- NTSC : 1~ MAX 30 IPS
I Records before-event (Alarm or Motion) data based on pre-set hours. (Pre-Alarm)
- 0 ~ 5SEC
I Audio-records and plays back selected channels.
I Offers a timer used for time record.
I Records video and audio with alarm.
I Offers various playback speeds.
I Offers easy-to-use search functions.
- Date & Time Search, Event(Record, Alarm, Motion, Timer) Search
I Instantly pauses the current screen. (FREEZE)
I Offers 2X Zoom for video images monitored or played back by the user.
I Offers a variety of screen split modes.
- Full Screen Display, 4 Split Display, Sequence Display, PIP Display
I Allows the user to enjoy audio and video over a PC monitor through VGA Out.
1-2
English
Download from Www.Somanuals.com. All Manuals Search And Download.
SHR-1040/1040K USER’S MANUAL
3
Part Names & Function
[SHR-1040]
No.
Name
Power LED
Function
Displays power On/Off condition.
lights on when an event occurs.
Alarm LED
HDD LED
Rec LED
1
Displays Normal Access to HDD. Upon Access to HDD, LED
repeats on and off.
Displays the record condition.
1
4
The screen is switched to Single Mode when each channel
key is pressed during live programming, and the screen of
the channel is displayed in Full Screen.
CH1, CH2,
CH3, CH4
2
...
During initial booting, the screen is displayed in four split.
When the Mode Key is pressed, the screen is switched to
single or split screen.
MODE
Screen Split
Selection Button
3
4
5
Enters the date/time of video and audio signals recorded in HDD,
select events from the RECORD and ALARM EVENT SEARCH,
and views the POWER EVENT LIST and LOSS EVENT LIST.
SEARCH
MENU
SEARCH
MENU
Displays the MAIN MENU, and exits the MENU Screen by
pressing the button again.
Enters the PIP Mode when the PIP Button is pressed in the
Single Screen. There must be two or more input channels.
(1) PIP is enabled when the sequence of the Single Screen
(Main Screen) is turned off.
PIP
6
(2) The Main Screen moves to Channel 1, 2, 3 and 4 in
sequence when the up/down or left/right button is pressed.
(3) Main-Sub switching: The screen is switched when the Enter
Button is pressed in the PIP Screen while the Sequence is
turned off.
PIP
1-3
English
Download from Www.Somanuals.com. All Manuals Search And Download.
No.
Name
Function
You can view X2 screen by pressing the ZOOM Button in
the single screen.
ZOOM
7
ZOOM
When you press the up/down and the left/right key in the
Zoom screen, the selected Zoom Area moves. Press the
Enter button to view X2 Zoom Screen of the selected area.
Press the Freeze Button to freeze the current displayed
screen, and press the Freeze Button again to cancel the
Freeze.
The Freeze marker is displayed on top of the screen in
Freeze Mode.
FREEZE
8
9
FREEZE
SEQUENCE
ALARM
When pressing the Sequence Button in the Single Screen,
the screen is switched to each channel with video In.
SEQUENCE
When the Alarm Button is selected, the Alarm is canceled.
In Normal Record Mode, video signals are recorded.
ALARM
10
11
RECORD
Fast Reverse: Used for fast search in reverse direction
playback.
Step Reverse: Used for cut-by-cut search in reverse
direction during pause.
Fast/Step
Reverse
12
Ends search during playback and recording.
STOP
13
14
Operates in toggle for play/pause during playback.
PLAY/PAUSE
Fast Forward: Used for fast search in forward direction
during playback.
Step Forward: Used for cut-by-cut search in forward
direction during pause.
Fast/Step
Forward
15
Direction key used to set the details of the Menu.
➛
œ
❿
Used to increase the value of setting, or direction key used
to set the details of the Menu.
16
Direction key used to set the details of the Menu.
Used to decrease the value of setting, or direction key used
to set the details of the Menu.
❷
Plays the role of Enter Key when setting the Menu.
➛
1-4
English
Download from Www.Somanuals.com. All Manuals Search And Download.
SHR-1040/1040K USER’S MANUAL
[SHR-1040]
Caution
The ventilation outlet may be blocked. Do not operate the DVR on a carpet or other soft surfaces.
When you operate the DVR in a cabinet or on a rack, check whether a ventilation device is properly installed.
No.
Name
Function
1
Connector linked to the Port DIY CAMERA.
CAM IN RJ-11
Composite video signal input connector (BNC Style
Connector)
BNC VIDEO IN
2
Composite video signal output connector (BNC Style
Connector)
3
4
BNC VIDEO OUT
VGA
VGA video signal output connector
Audio signal input connector (RCA Jack)
5
6
AUDIO IN
RCA VIDEO OUT
RCA AUDIO OUT
Video signal output connector (RCA Jack)
Audio signal output connector (RCA Jack)
7
- ALARM IN: Alarm input connector. Receives alarm signals
from outside.
- ALARM OUT: Alarm output connector. Sends alarm signals to
external devices.
8
ALARM
DC IN
- ALARM RESET: Alarm reset connector
9
Supports 12V power socket.
1-5
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Controller
4
1. RECORD
15. SYSTEM ID
Starts the recording as the setup
record setting in normal record
mode.
Confirms system and remote
control ID and changes the
remote control ID.
2. ID RESET
16. PIP
The ID is reset.
In Single mode, press to watch
another channel in a sub picture.
3. NUMBER KEY
Press to select one of single
channels in Live mode. Use this
for typing purposes in a numeric
input mode.
17. SEQUNCE
The single channel mode switch-
es according to the specified time
on the menu.
4. MODE
18. ALARM
Selects split-screen
.
Cancels the alarm while the
alarm is going off.
5. FREEZE
Runs the FREEZE function in live
mode.
II
19.
Play/Pause : pauses and
resumes the search screen
while in play.
6. ZOOM
Press to enlarge the single chan-
nel picture to its double.
20 .
FF (fast forward) : used for
quick forward search while in
play.
(STOP)
7.
8.
Ends search during playback and
recording.
21. SEARCH
Searches for data on the HDD.
FR (fast reverse) : used for quick
backwardsearch while in play.
22.
9. MENU
Used for changing settings
or for moving the cur-sor
up/down/left/right in live
mode and on the menu and
search screens.
Either goes to the system menu
screen or moves to the upper
menu from the lower menu.
➛
10.
(ENTER)
Shows the cursor for the
channel selection in live mode or
used as the select button for
menu setup.
23. PWD LOCK
You can check if the password lock
(PWD LOCK) is set to ON/OFF.
24. SYS INFO.
You can check out information on the
system version.
11. REC LOCK
You can check if REC LOCK is set to
ON/OFF.
25. CH 3
Displays SINGLE CH 3.
12 . MONITOR OUT
You can check which mode is set for
the current monitor output.
26. CH 4
Displays SINGLE CH 4.
13. CH 1
Displays SINGLE CH 1.
14. CH 2
Displays SINGLE CH 2.
To change the remote control ID
While pressing the SYS ID key, enter the numeric ID in two digits (Default ID: 00).
ex) If you want to change the remote control ID to “08”: While pressing the SYS ID key, enter 0 and 8 and press it again to check if the ID is
changed to 08.
1-6
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Installation
2
English
Download from Www.Somanuals.com. All Manuals Search And Download.
SHR-1040/1040K USER’S MANUAL
Installation Environment Setup
1
Do not play DVR on the carpet or other soft material to prevent clogging of the air ventilator.
To play DVR on the cabinet or rack, be sure to check the ventilation condition.
You should pay attention to the following before you use the product.
1. Do not use it outdoor.
2. Do not let water or liquid in the connection part or the product itself.
3. Do not impose excessive shock or force.
4. Do not pull out the power plug unreasonably.
5. Do not disassemble the product on your own.
6. Do not exceed the rated input or output range.
7. Use certified power cord only.
8. Use the power cord with a ground for the product with an input ground.
2-1
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking Product & Accessory
2
Upon delivery of a product, you shall unwrap the product and put it on the even floor or where
you want to use it. Then you shall check if the following items are in it.
SHR-1040
SOC-N120
Battery Alkaline
(AB39-10601F)
User’s Manual
(B68-00592A)
Adapter
Power Cord
Remote Controller
(AB59-00023A)
(AB44-00015A)
(AB39-10601F)
SOC-C120 Camera Bracket Camera Cable
Screw
Sensor Connector
NO
1
2
3
4
5
6
7
8
Item
DVR
User’s Manual
Warranty Card
Adapter
Power Cord
Remote Controller
Battery Alkaline
Model
SHR-1040
Q’ty
1
1
1
1
1
1
2
2
2
4
4
12
4
SHR-1040/XAA SHR-1040K/XAA
o
o
o
o
o
o
o
x
x
x
x
x
x
o
o
o
o
o
o
o
o
o
o
o
o
o
-
-
ADP-5412WD
-
-
-
SOC-N120
SOC-C120
SBR-110S
MCB-60
-
CAMERA
9
10
11
12
13
Camera Bracket
Camera Cable
Screw
Sensor Connector
-
SHR-1040/XAA : No.1 ~ No.7 items are only included.
WARNING) SHR-1040 set must use the adapter we provide.
2-2
English
Download from Www.Somanuals.com. All Manuals Search And Download.
SHR-1040/1040K USER’S MANUAL
HDD Addtion
3
You can install one additional hard disk drive inside the product (Max. 2 HDDs). However, there are lots of factors inside that
may cause electrical shock, physical damage or malfunction. So please follow the instructions below to mount the HDD as
the product couldn’ t recognize the additionally installed HDD or may not work properly due to incorrect installation or connec-
tion.
[Installation Instructions]
• Make sure that any cable should NOT be stuck between components inside and do NOT use an uninsulated cable of which
coating is stripped off (Otherwise, it can cause fire or malfunction).
• Any sharp edges inside the product can cause a physical damage during the installation.
• Keep the screws or components removed for HDD addition in a place where you can easily locate them when necessary.
Uninstalled screws or components can cause malfunction or inoperability.
[To install an additional HDD]
1. Loosen the screws, two on each side (left/right) and three on the rear, to remove the cover.
2. Remove the cover.
(Push the cover back before lifting up on the rear side)
3. There is a bracket (BRACKET-HDD) inside for mounting and fixing the HDD.
BRACKET-HDD
2-3
English
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Disconnect the power supply cable and the signal cable (IDE cable) from the current HDD. Push the
bracket to the arrow direction as in the picture below and lift it up from the bottom.
6. Use the four screws provided (SCREW-SPECIAL: PWH,+,-,6-32UNC,L14.7(4.2),ZPC) to fix the old HDD
and the additional with the bracket
(Make sure you fasten the screws firmly so that they are not loose from vibration).
2-4
English
Download from Www.Somanuals.com. All Manuals Search And Download.
SHR-1040/1040K USER’S MANUAL
7. Mount the HDD-fixed bracket to its original position. (Installation is done in the reverse order of the disas-
sembly. Fit the bracket (BRACKET-HDD) into the bottom hole and fix the screw).
8. When done (make sure the bracket is firmly fixed), connect the power supply cable and the signal cable
(IDE) to both the old and the additional HDD (see the picture below).
9. Check if all the connections (connectors) are properly made and firmly fixed, and close the cover.
2-5
English
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Use the screws (two for each side and one for the rear) in step 1 above to fix the cover.
2-6
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3.
DIY Carmera
3
English
Download from Www.Somanuals.com. All Manuals Search And Download.
SHR-1040/1040K USER’S MANUAL
Standard Camera
1
Composition and Installation Method
1) STANDARD CAMERA COMPOSITION (SOC-C120)
a. Lens
It has a focal length of 3.8mm and makes it possible for you to observe a relatively wide area.
b. Microphone
Capable of picking up all sound in the vicinity of the camera location and transmitting to the monitor.
c. Camera fitting groove
Enables the camera to be fixed onto the bracket. You may install it either above or below the camera if
necessary.
d. 6-pin modular jack
Used to connect the camera to the monitor.
e. SENSOR jack
Used to connect the sensor to the camera.
f. Speaker
Outputs the sound signal.
3-1
English
Download from Www.Somanuals.com. All Manuals Search And Download.
2) INSTALLING STANDARD CAMERA (SOC-C120)
SOC-C120 camera can be attached to the wall, ceiling or shelf using the camera mount bracket
(SBR-110S).
Choose an installation site that can sufficiently support the weight of the equipment to be installed.
Attach the camera mount bracket to the wall or ceiling using the supplied three screws
(M4 X L15).
Adjust the camera to target the video location and tighten the bracket handle on the camera mount
bracket.
3) CAMERA MOUNT BRACKET(SBR-110) & STANDARD CAMERA(SOC-C120)
(1) Overview
CAMERA MOUNT BRACKET (SBR-110S) is used to attach the camera to a wall, ceiling or shelf.
(2) Specifications
Use : Indoor
Installation : Wall or Ceiling
Dimensions : 2.25 (W) X 1.86(H) X 3.95(L) inches
Weight : 0.29 Ibs
Operating Temperature : 32°F ~ 104°F
(3) Accessories
SCREW (M4 X L15) : 3 pcs
(4) Installation
Explains the installation of CAMERA MOUNT BRACKET installation, as well as installation of the
camera onto the CAMERA MOUNT BRACKET.
• Choose an installation site that can sufficiently support the weight of the equipment to be installed.
• Attach the camera mount bracket to the wall using the supplied screws (M4 X L15).
3-2
English
Download from Www.Somanuals.com. All Manuals Search And Download.
SHR-1040/1040K USER’S MANUAL
• Adjust the camera to target the video location and tighten the bracket handle on the camera mount
bracket. Install the camera on to the male screw of the Camera Mount Bracket by rotating the camera
in clockwise.
• Loosen the handle by turning it in a counter-clockwise direction and then adjust the camera position .
Tighten the handle, turning it clockwise, and lock the camera in position.
• Connect the camera cable to the camera.
3-3
English
Download from Www.Somanuals.com. All Manuals Search And Download.
After positioning the monitor and installing four cameras in the desired location, please
connect the CAMERA to the DVR using the CAMERA CABLE (MCB-60) as shown
in the figure below.
Connection status checking method :
• Turn on the DVR after connecting cameras, and check if camera image is displayed.
• If the DVR and the camera are not connected properly, OSD ‘L’(LOSS) will be displayed on screen.
3-4
English
Download from Www.Somanuals.com. All Manuals Search And Download.
SHR-1040/1040K USER’S MANUAL
Nightvision Camera
2
1) Before Installation
SOC-N120 INTRODUCTION
SOC-N120 Nightvision camera is intended to be used exclusively with those sold by this company for
DIY. With the built-in IR LED and light sensor in the camera, both day monitoring and night monitoring
are possible. Also, since it is designed as water-proof daily product, it can be used not only indoors, but
also outdoors.
2) Precautions for Installation and Operation
Installing SOC-N120
* Make sure the installation location is a place where 5 times (about 1 kg) of the total weight of the cam-
era can be tolerated before installing the camera.
* When installing the camera, make sure the cable is not squeezed in an inappropriate place or the insu-
lation plastic is removed (it will be a cause for malfunction or fire).
* Keep personnel away from under the installation location because there is a risk of object falling during
installation. Move precious items to a safe place as well before the installation.
* Install SOC-N120 in a cool place where there is no direct sunlight.
* Do not expose SOC-N120 to direct sunlight during operation or storage.
* SOC-N120 should always be used in a place where certain temperature and humidity can be main-
tained (as specified below).
- Temperature: 14°F ~ 122°F
- Humidity: Below 90%
3-5
English
Download from Www.Somanuals.com. All Manuals Search And Download.
3) Installation
1. Make sure the installation location is a place
where 5 times (about 2.2lbs) of the total weight
of the camera can be tolerated before installing
the camera.
2. Connect the cable below the camera after
attaching the provided Mount Bracket to the
desired place.
3. Use the handle on the Mount Bracket to
adjust the direction you want to setup for
monitoring.
SOC-N120 Pin Configuration
1
2
3
4
5
6
SP-
VIDEO_OUT
GND
SP+
ALM/AUDIO
VDD
3-6
English
Download from Www.Somanuals.com. All Manuals Search And Download.
SHR-1040/1040K USER’S MANUAL
4) Title of Each Component
a). Lens
- It has a focal length of 3.8mm and makes it possiblefor you to observe a relatively
wide area.
b). Illumination Sensor
- Detects incoming light to control the IR LED.
c). IR LED
- This is an infrared LED that is controlled by the illumination sensor.
d). Camera fitting groove
- Enables the camera to be fixed onto the bracket. You may install it either above or
below the camera if necessary.
e). Speaker
- Used to connect the sensor to the camera.
f). SENSOR jack
- It outputs the sound signal which was transfered from alarm sensor.
g). Microphone
- Capable of picking up all sound in the vicinity of the camera location and
transmitting to the monitor.
h). 6-pin modular jack
- Used to connect the camera to the monitor or DVR.
3-7
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4.
Connecting with
other device
4
English
Download from Www.Somanuals.com. All Manuals Search And Download.
SHR-1040/1040K USER’S MANUAL
Connecting the Video, Audio, and Monitor
1
[SHR-1040]
Caution
- Do not connect the Video In (BNC Input) and the RJ-11 (DIY Camera) input with the same
channel at the same time. If connecting them simultaneously, two input signals may be
mixed when outputting. This is not the product defect; so, please connect only one between
the two inputs.
- When the first delivery, the Video output is set to the CVBS (BNC Output) output. If viewing
on the VGA Monitor, set it in the MENU first.(Refer to 6-12 page)
- The same Video signal is outputted for the BNC Out and the RCA Out of the Video out.
Use by connecting the desired port.
4-1
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Alarm Input/Output
2
The Alarm IN/OUT port in the back of SHR-1040 is composed of the following
elements.
ALM OUT
G
ALM RST
ALM IN
G
ALARM IN/OUT Connection
Name
Function
1
2
ALM IN
ALARM Input Port
ALM OUT
ALARM Output Port
On receiving an ALARM RESET signal, the sys-
tem cancels the current ALARM input and output
signal and then resumes sensing.
3
ALM RST
4-2
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5.
Basic Operation
5
English
Download from Www.Somanuals.com. All Manuals Search And Download.
SHR-1040/1040K USER’S MANUAL
System Operation
1
Turning Power On
G
When the adapter is connected to the DC 12V connector on the back panel, the Power LED
on the front is lit. The following screen appears, and the system is booted.
Detection of Video In Signals
G
If no video signals exist when the system is turned on, the letter L (for Loss) lappears next
to the title (CAM1…CAM2) of the screen, and the screen turns black.
Connect a video signal, and the letter L will disappear. You can check the Video Loss Event
on the Loss Event List of the Search Menu.
5-1
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Live Screen Mode
2
Full Display Screen
Markers and displays on the screen are seen as below.
Play
01/01/06 12:00:00
AML CAM 1
S
AML CAM 2
AML CAM 4
AML CAM 3
For Live, it indicates the current time and date as set in the system.
For playback, it indicates the time and date of the data recording.
05/05/01 00:00:01
marker is displayed when the system in recording mode.
Prevents the cancellation of REC.
PLAY
Indicates playback at normal speed.
Indicates pause.
2
4
Indicates X2 reverse playback.
Indicates X4 reverse playback.
8
Indicates X8 reverse playback.
16
32
64
Indicates X16 reverse playback.
Indicates X32 reverse playback.
Indicates X64 reverse playback.
Indicates X1 forward playback.
2
4
Indicates X2 forward playback.
Indicates X4 forward playback.
8
Indicates X8 forward playback.
16
32
64
Indicates X16 forward playback.
Indicates X32 forward playback.
Indicates X64 forward playback.
Used for cut-by-cut search in reverse direction during pause.
Used for cut-by-cut search in reverse direction during pause.
A
L
A marker appears when the system is in Alarm recording mode.
Indicates the VIDEO LOSS state.
M
M marker appears when the system is in Motion record mode.
marker appears when the system is in Time record mode.
5-2
English
Download from Www.Somanuals.com. All Manuals Search And Download.
SHR-1040/1040K USER’S MANUAL
Key Functions
3
1. CHANNEL KEY & MODE KEY
G
G
G
Use the CHANNEL Key when you want to view the channel in full screen.
Press the desired channel key to view the channel in full screen.
Audio of the channel is also selected. The S mark appears next to the title of the selected
channel, and the audio of the channel is off.
G
G
Audio recording is available for the one selected channel.
Press the MODE Key to view the 1CH MODE and the QUAD MODE in turn as shown in the
picture.
2. PIP KEY
G
G
G
G
G
Use the PIP Key to view the main and the sub screen at the same time.
You can view the two channels when pressing the PIP button in the 1CH mode.
Press the ENTER Key in PIP mode to switch the main and sub screen.
Press the PIP Key again to exit the PIP state and enable the Single screen mode.
Press the FREEZE Key to freeze the main screen only. On the top right of the screen,
‘||’(FREEZE MARK) appears.
G
G
Clear the Freeze before operating another key.
Press the Sequence Key in the PIP mode PIP to automatically sequence to the sub screen.
(Auto sequence is cleared when pressing the Sequence Key again.)
Sequence in the PIP MAIN CHANNEL 1 screen
☛
SUB2 ➝ SUB3 ➝ SUB4 ➝ SUB2
5-3
English
Download from Www.Somanuals.com. All Manuals Search And Download.
3. ZOOM KEY
G
G
G
G
The ZOOM Key is used to X2 zoom the selected area in 1CH mode.
Press the ZOOM Key to display the ZOOM area (default: Center Area).
Press the ZOOM Key repeatedly to display or clear the ZOOM area.
Press the ZOOM Key to zoom the selected area, and press the ENTER key to clear the
ZOOM and display the marked area.
G
ZOOM function is operated in the Single screen mode. SINGLE.
4. FREEZE KEY
G
G
The FREEZE Key is used to pause the screen.
Press the Freeze Key to display the‘II’marker on the top right. The screen is paused.
Press the Freeze Key again to make the‘II’marker disappear and clear the pause screen.
5-4
English
Download from Www.Somanuals.com. All Manuals Search And Download.
SHR-1040/1040K USER’S MANUAL
5. SEQUENCE KEY
G
G
The Sequence Key is used for automatic channel sequencing. It is enabled only in Live Mode.
Channels are switched in sequence and the Loss channel without video signals are skipped
during the Dwell Time set by the Setup Menu.
(Switch from 1channel ➝ 2 channel)
☛
☛
Sequence in the Full Screen
CH1 ➝ CH2 ➝ CH3 ➝ CH4 ➝ CH1 ➝ CH2 ➝ CH3 ➝ CH4 ➝ ......
Sequence of the Main Channel 1 in the PIP Screen
SUB2 ➝ SUB3 ➝ SUB4 ➝ SUB2 ➝ ......
6. ALARM KEY
G
Cancel the alarm when alarm is enabled.
5-5
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6.
Menu Setup
6
English
Download from Www.Somanuals.com. All Manuals Search And Download.
SHR-1040/1040K USER’S MANUAL
Main Setup Menu
1
1. CLOCK/DISPLAY
- Set the time, date and display items.
2. RECORD MODE
- Set record-related items.
3. TITLE SETUP
- Set channel titles.
4. DWELL TIME SETUP
- Set the dwell time for each channel for sequence operations.
5. ALARM SETUP
- Set the alarm channels and setup/alarm-related items.
6. EVENT RECORD MODE
- Set the recording and motion detection items when the alarm is on.
7. TIMER RECORD MODE
- Set the time record.
8. SYSTEM SETUP
- Set the initiation of the system and the password.
9. SYSTEM INFORMATION
- Displays the HDD capacity and the system software version.
6-1
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Clock/Display Setup
2
G
Set the time, date and display items.
(1) DATE TYPE
- Date can be displayed in three types, and the user can choose one among the three.
[YY/MM/DD, MM/DD/YY, DD/MM/YY]
(2) DATE
- Set the present data.
(3) TIME [HH:MM:SS]
- Set the present time.
(4) DATE/TIME
- Set the date/time to ‘‘On’’ to display it on the screen, set the date/time to ‘Off’ to not display it.
[ON/OFF]
(5) STATUS
- Set the system status ‘On’ to display playback information when record or play back recorded video,
and set the status to ‘Off’ to not display such information.
[ON/OFF]
(6) BORDER
- Display or hide the border of the screen. Set the border to ‘On’ to display the border, and set the bor-
der ‘Off’ to not display the border.
[ON/OFF]
(7) BORDER COLOR
- The border color can be defined in three colors.
[GRAY/WHITE/BLACK]
(8) PIP POSITION
- Set the location of the sub screen.
[B-RIGHT/B-LEFT/T-RIGHT/T-LEFT]
6-2
English
Download from Www.Somanuals.com. All Manuals Search And Download.
SHR-1040/1040K USER’S MANUAL
Record Mode Setup
3
(1) PICTURE QUALITY
- Define the picture quality in three steps when recording. High means top quality, followed by
Normal and Low.
[NORMAL/HIGH/LOW]
(2) PICTURE RATE
- Set the number of record fields for video In.
[1/2.5/3.75/7.5/15/30]
(3) DISK END MODE
- When the mode is set to Stop, recording is stopped if the HDD becomes full during recording.
- When the mode is set to Continue, new data overwrites previously recorded data during recording. The
oldest data saved will be overwritten first.
[CONTINUE/STOP]
(4) DISK END ALARM TONE (HDD-full alarm mode)
When the Disk End mode is set to Stop, the alarm tone rings if the HDD becomes full during recording
if the tone is ‘On.’ The alarm tone does not ring if the tone is ‘off’. The tone is enabled when the Disk
End Mode is set to Stop.
[ON/OFF]
(5) RECORD TIME MARK (Record time display)
- When the mark is set to ‘On’, the time of recording is displayed during playback. When the mark is set
to ‘Off’, the time is not displayed.
[ON/OFF]
(6) RECORD TITLE MARK (Record title display)
- When the mark is set to ‘On,’ the title of recording is displayed during playback. When the mark is set
to ‘Off,’ the title is not displayed.
[ON/OFF]
6-3
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Title Setup
4
G
The default settings of the title setup menu are shown as follows.
(1) TITLE SETUP
- You can set the title of each channel as you want.
➛
- You can change the title by using …,†,œ,√,
0 1 2 3 4 5 6 7 8 9
ABCDEFGHIJKLMNOPQRSTUVWXYZ
: = . ( ) [ / ] _ + -
- Place the cursor on the “ ” area when the title is not displayed. Press Enter to
delete OSD.
6-4
English
Download from Www.Somanuals.com. All Manuals Search And Download.
SHR-1040/1040K USER’S MANUAL
Dwell Time Setup
5
G
The default settings of the Dwell Time are shown as follows.
(1) DWELL TIME SETUP
- Press the Sequence button in single screen to enter Sequence Mode. You can set the dwell time of
each channel before switching.
When the Dwell Time is set to 0 seconds, the channel is skipped and the next channel appears.
[0SEC, 1SEC, 2SEC, 3SEC.................... ~ 60SEC]
6-5
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Alarm Setup
6
G
The default settings of the Alarm Setup Menu are shown as follows.
(1) ALARM SETUP
- Set the alarm setup to ‘ON’ to enable the alarm of each camera. Set the setup to ‘OFF’ to disenable
alarm. [ON/OFF]
(2) HOLD TIME
- When Alarm occurs, set the hold time of alarm.
[5SEC, 6SEC, 7SEC, 8SEC ~ 59SEC , 1MIN, 2MIN, 3MIN ~30MIN]
(3) ALARM ON TIME
- Set the start time of alarm operation. When the ALARM ON TIME and the ALARM OFF TIME are set,
alarm is detected during the period.
[00:00~23:59]
(4) ALARM OFF TIME
- Set the end time of alarm operation.
[00:00~23:59]
(5) ALARM TONE
- When the ALARM TONE is set to ‘ON’, the Alarm Tone rings when alarm is detected.
[ON/OFF]
6-6
English
Download from Www.Somanuals.com. All Manuals Search And Download.
SHR-1040/1040K USER’S MANUAL
Event Record Mode Setup
7
G
The default settings of the Alarm/Motion Recording Setup menu are shown as follows.
(1) EVENT RECORD ENABLE
Set the EVENT RECORD ENABLE to ‘On’ to start recording when alarm occurs, and set the EVENT RECORD
ENABLE to ‘Off’ to not start recording when alarm occurs. If you exit the menu after setting the EVENT RECORD
ENABLE to ‘On’, the system records data whenever an alarm occurs.
The following screen shows that the system records a program after an alarm occurs. The ‘A’ mark before the title of
the channel indicates that an alarm occurred.
[ON/OFF]
(2) PRE ALARM TIME LIMIT
- The Pre Alarm Time Limit enables users to know the state of the system before a motion is detected
or an alarm occurs. It decides the length of time for recording video and audio data input right before
motion or alarm. The system always stores 0 to 5second-long video and audio data in the memory,
and records data during the pre-set time set by the Time Limit in HDD when alarm recording starts.
[ 0, 1SEC, 2SEC, 3SEC, 4SEC, 5SEC ]
(3) POST ALARM TIME LIMIT
- After recording data as set by the MAIN ALARM TIME, the system records additional sec-
onds as set by the POST ALARM TIME Limit.
[10SEC ,20SEC ,30SEC ,1MIN ,2MIN ,3MIN ,4MIN , 5MIN]
6-7
English
Download from Www.Somanuals.com. All Manuals Search And Download.
(4) MOTION DETECTION
- When the Motion Detection is set to ‘ON’, the system records input video whenever a
motion is detected.
[ON/OFF]
(5) SENSITIVITY
- You can set the level of sensitivity of motion detection when setting motion detection.
HIGH/NORMAL/LOW. High indicates the highest level of sensitivity of motion detection,
and Low indicates the lowest level of sensitivity of motion detection.
[HIGH, NORMAL, LOW]
(6) MOTION CH SETUP
- Set the channel from which a motion is detected.
-
You can divide the motion detection area into total 9 for each channel.
The following screen displays to activate only No. 1 area of No. 1 channel. You can use the direction key to
move the area around and select FULL for the motion detection on the whole screen.
With MOTION DETECTION set to ON, if no motion is detected in the specified area while a motion is sensed in
other areas, MOTION DETECTION will not operate.
6-8
English
Download from Www.Somanuals.com. All Manuals Search And Download.
SHR-1040/1040K USER’S MANUAL
- Motion is detected only from channels set to ‘On.’
The following screen shows motion recording after motion detection. A motion is deteced in the
Channel 1. The ‘M’ mark before the title of each channel indicates that a motion is
detected.
[ON/OFF]
Timer Record Setup
8
(1) TIMER: Set the Timer to ‘On’ to enable timer recording. [ON/OFF]
(2) DAY: Set the day of the week to record data.
[MON, TUE, WED, THU, FRI, SAT, DAILY, SUN]
(3) START & END: Set the start and ending time of recording. [00:00~23:59]
(4) FIELD RATE: Set the number of fields to record per second.
[1/2.5/3.75/7.5/15/30]
6-9
English
Download from Www.Somanuals.com. All Manuals Search And Download.
System Setup
9
(1) PASSWORD
- The default password : 4321
- You can set the password to limit access to the Main Screen setup by unauthorized people.
(Create a four-digit password by choosing between 1~4.)
You can enter the password from No. 1 to No. 4 using the corresponding channel key.
Once the password is entered, you’ll see the following message that asks if you want to change the password. If
you want to change it, click OK and if not, click CANCEL.
(2) PASSWORD LOCK
When the user sets the Password Lock after setting a password, he or she has to enter the password
whenever entering the menu.
[ON/OFF]
6-10
English
Download from Www.Somanuals.com. All Manuals Search And Download.
SHR-1040/1040K USER’S MANUAL
(3) RECORD LOCK
If you set RECORD LOCK to ON and press STOP to release the current recording, you are prompted to
enter the PASSWORD.
(4) HDD ERASE
If you exit the Menu after setting HDD ERASE to ON, you will see the following message that asks if you
want to erase the data on the HDD. If you click OK, you’ll see “HDD ERASE” as in the next picture, and the
existing HDD Data is erased. If you click CANCEL, the HDD data will not be erased.
[ON/OFF]
Caution
Deleted data cannot be restored. Check data carefully again before deleting data.
(5) FACTORY RESET
When FACTORY RESET is enabled, the settings are reset to the factory default.
If you exist the menu after setting FACTORY RESET to ON, you’ll see the following mes-
sage that asks if you want to perform FACTORY RESET. If you click OK, the settings are
reset to the factory default with a message of “FACTORY RESET” as in the next picture. If
you click CANCEL, FACTORY RESET will not perform.
[ON/OFF]
6-11
English
Download from Www.Somanuals.com. All Manuals Search And Download.
(6) SYSTEM ID
Set the System ID to use the Remote Controller.
When using more than one unit of the system, a number of systems may be operated at the same time
with a single remote controller. Set the different IDs for different units.
Press the System ID of the Remote Controller and use the number keys to create IDs.
After the setting, systems with IDs that correspond to the ID of the remote controller will operate.
[0,1,2 ~ 8,9]
(7) MONITOR OUT
Selects the Video Out of the System.
When the Video Out is set at CVBS, the video out is sent through BNC and RCA Video Output port.
When the Video Out is set at VGA, the video out is sent through VGA Video Out port, and seen on the
PC monitor. After changing the settings and existing the menu, the system is automatically rebooted.
After rebooting, the change is applied.
[CVBS/VGA]
(8) 1CH RECORD SUPPORT
If you set 1CH RECORD SUPPORT to ON, the system switches from 4-channel to 1-channel mode.
Then, a selected channel will be the number 1 channel.
If you exist the menu after setting 1 CH RECORD SUPPORT to ON, you will see the following
message that asks if you want to change the SYSTEM into 1 channel mode. If you click OK, the
system switches.
6-12
English
Download from Www.Somanuals.com. All Manuals Search And Download.
SHR-1040/1040K USER’S MANUAL
Once the system switched to 1 channel mode, all system functions operate in 1 Channel mode and
the items of other channels in the MENU are deactivated.
Once the system switched to 1 channel mode, you can just play the data in this mode and the data recorded in 4
Channel mode could not be played. On the contrary, in 4 Channel mode, the data recorded in Channel 1 mode will
not be run and only the data recorded in 4 Channel can be played.
If you want to switch from 1 channel mode back to 4 channel mode, set 1CH RECORD SUPPORT to OFF and exit
the MENU. Then, you will see the following message that asks if you want to switch the system mode. If you click
OK, the system will be switched.
Note
The hidden key is a shortcut key that is used in the following cases:
- If you have set the password lock but don’t remember the password, so that you couldn’t access the menu.
- If the current settings of MONITOR OUT does not match those of the current monitor connected, so that
you couldn’t see the display.
Press and hold down one of the hidden keys below for 5-10 seconds to activate it.
1. MODE KEY + CH1: MONITOR OUT Changes the settings of MONITOR OUTPUT. Once the settings are
changed, the system automatically reboots. Connect the monitor that matches the changes of the settings.
2. MODE KEY + CH2: FACTORY RESET
The system settings are all reset to the factory default. If you press this hidden key under the password
lock, the password lock will be set back to OFF (default) and you can access the menu.
3. MODE KEY + CH4 + ZOOM: FACTORY RESET + HDD ERASE
The system settings are all reset to the factory default, and data stored on the HDD are all erased. Note
that all data on the current HDD will be erased if you press these buttons.
6-13
English
Download from Www.Somanuals.com. All Manuals Search And Download.
System Information
10
(1) HDD NO
Displays HDD quantity that is installed on the system.
(2) CAPACITY
Displays the HDD capacity of the System.
[Remaining Capacity/Entire HDD Capacity]
(3) VERSION
Displays the version of the System.
6-14
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7.
Recording
7
English
Download from Www.Somanuals.com. All Manuals Search And Download.
SHR-1040/1040K USER’S MANUAL
Basic Recording
1
Press the Record button ( G ) to record live video. The Rec LED is lit, and the ( G ) mark
appears on the screen. The HDD LED blinks, indicating that data is being recorded to the HDD.
Note
You cannot record previously recorded data now being played back. To record the data, you
must stop the playback of the data first.
Timer Recording
2
- You can set the time and date of recording. From the menu list, enter the day of the week
(Mon. to Sun. or daily) and the time in the TIME RECORD MODE.
- Recording starts and proceeds on the scheduled time and date for the specified hours.
Note
Enter the Time Record Mode from the Menu screen, and set On/Off before setting the time
and date of recording. You can also set the number of fields to be recorded per minute.
7-1
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Motion Recording
3
Start recording when a motion is detected in the channel and area set by the Alarm/Motion
Record Setup menu. When the motion record begins, the M mark is displayed next to the
channel, indicating recording is on.
Note
- To enable the motion detection, you have to set an area for each channel. MOTION DETEC-
TION operates only if there is a motion detected in the area of the channel you have selected.
Alarm Recording
4
The Alarm In connector is located in the external in/out port of on the back panel of the
system. You can connect the connector with an external device.
Then, set the EVENT RECORD ENABLE ‘On’ in the EVENT RECORD SETUP menu to
start recording when an alarm occurs. When recording starts, the following screen appears.
Caution
Recording stops when the connection with input video signals is interrupted during recording.
The system starts recording again when connection to input signals is restored. The system
does not start recording when video signals are not connected to the Video In end.
7-2
English
Download from Www.Somanuals.com. All Manuals Search And Download.
SHR-1040/1040K USER’S MANUAL
Stop Recording
5
G
Click the Stop button to stop data recording.
The REC mark disappears as follows, and recording is stopped.
To stop data recording, click the STOP button.
The REC mark disappears and the current recording stops as shown in the
picture. However, if RECORD LOCK is set to ON, you have to enter the password
to stop recording.
7-3
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8.
Search & Playback
8
English
Download from Www.Somanuals.com. All Manuals Search And Download.
SHR-1040/1040K USER’S MANUAL
Search Menu
1
G
Search Menu
Press the Search button in Live mode to search recorded data.
The following screen appears.
Search is not enabled during recording. Stop recording to start search.
- DATE & TIME SEARCH : Search recorded data based on the time and date.
- RECORD EVENT SEARCH : Searches for all data recorded in Normal Record or Timer
Record.
- ALARM EVENT SEARCH : Search all the data recorded in the Alarm/Motion mode.
- LOSS EVENT LIST : Display information on the channel and time at the time of Video Loss.
- POWER EVENT LIST : Display information on On/Off time of power.
G
Menu Operation
Move to the menu items by using the left/right and up/down buttons (œ,√,…,†). The
selected item is highlighted and displayed with the cursor. Press the Select button to
enter the sub menu. In the sub menu, you can enter conditions for data search or
select from the list of the recorded data to play back data you want.
G
G
Enter Search Conditions & Select from the List
Time & Data Search Enter the conditions for data search in the menu, and press the
select button. You can either enter the conditions or select from the list as in the
general menu.
Move Up To Menu or End Search/Playback
To move up from the sub menu or end search, press the Menu button. To end play-
back after selecting data search, press the Search Key and exit through the Live
screen.
Warning
The current time and date is displayed in the Time and Date section of the Time/Date Menu.
Search recorded data by entering the time and date you want.
The list is not available in the Event Search menu at default, since data is not stored on the
HDD.
8-1
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Date Time Search
2
(1) DATE[YY/MM/DD]
Set the date (year/month/day) you want to search.
(2) TIME[HH:MM:SS]
Set the time you want to search.
(3) SEARCH START
Enter the year/month/day/hour/minute/second you want to search.
Press the Enter button (
) to search the time and date.
Record Event Search
3
G
The following screen appears when selecting the Record Event Search after pressing
the Search button.
G
Displays the list of the data recorded in NORMAL RECORD or TIMER RECORD out of all
data on the HDD.
Select from the Record Event List by using up/down left/right buttons (…,†,œ,√). Press
the Search button after selecting from the Record Event List to start search.
8-2
English
Download from Www.Somanuals.com. All Manuals Search And Download.
SHR-1040/1040K USER’S MANUAL
Alarm Event Search
4
G
The following screen appears when selecting the Alarm Event Search after pressing
the Search button.
G
Displays the list of the data recorded in ALARM or MOTION RECORD out of all data on the
HDD.
Select from the Record Event List by using up/down left/right buttons (…,†,œ,√). Press
the Search button after selecting from the Alarm Event List to start search.
Note
Enter the Time Record Mode from the Menu screen, and set On/Off before setting the time
and date of recording. You can also set the number of fields to be recorded per minute.
Loss Event List
5
G
Display the channel and the time and data at a time of Video Loss.
G
You can view the list on the following page by using the up/down/left/right buttons
(
…,†,œ,√).
8-3
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Event List
6
G
Display the list of the time and date record of Power On/Off.
G
You can view the list on the following page by using the up/down/left/right buttons (…,†,œ,√).
Note
Enter the Time Record Mode from the Menu screen, and set On/Off before setting the time
and date of recording. You can also set the number of fields to be recorded per minute.
Basic Playback
7
G
Press the Play/Still Button to play back the recorded data on the HDD.
The following screen appears and playback starts.
You cannot play back data during recording. You must stop recording and play back
data in Live mode.
G
The ‘No Data’ message is displayed when there is no recorded data.
8-4
English
Download from Www.Somanuals.com. All Manuals Search And Download.
SHR-1040/1040K USER’S MANUAL
Note
Enter the Timer Record Mode from the Menu screen, and set On/Off before setting the time
and date of recording. You can also set the number of fields to be recorded per minute.
G
G
When the system reaches the end of the HDD during playback or the end of the current data, the system will start
playing back from the beginning of the first data on the HDD.
When pressing the Play/Still button during playback, the following screen appears and
the screen is in Still mode.
,
(
)
G
If you press FAST FORWARD or FAST REWIND button
during playback, the
system plays the data fast forward or fast in reverse, respectively.
FAST FORWARD is available in 2X, 4X, 8X, 16X, 32X, and 64X and FAST REWIND,
-2X, -4X, -8X, -16X, -32X, and -64X.
,
(
)
G
G
When pressing the FAST FORWARD or FAST REWIND button
system plays back data cut-by-cut in reverse and forward.
during Still, the
(
)
If you press the FAST FORWARD
button during normal playback, the playback
speed increases forward. While you press the FAST REWIND ( ) button, the play-
back speed increases in reverse.
G
To restart playback, press the Play/Still button.
8-5
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9.
Appendix
9
English
Download from Www.Somanuals.com. All Manuals Search And Download.
SHR-1040/1040K USER’S MANUAL
Product Specification
1
1) SHR-1040, SHR-1040K
Block
Function
SHR-1040
SHR-1040K(DIY Kit)
etc
Signal Format
Video Input
NTSC
4 BNC, 4CH(RJ-11 DIY Camera)
2 BNC, 2RCA, 1VGA
1ch - FullScreen,
Video output
Video
Display Mode
Quad, Sequence,
Freeze, Zoom, PIP
Display Resolution
Audio Input
Audio Output
720 480
*
4CH(RCA), 4CH(RJ-11 DIY Camera)
2 CH(RCA)
Audio
1CH mode : 30IPS
4CH mode : 120IPS
MPEG4
Video REC/PB Speed
Video CODEC
Audio CODEC
G.723
Simplex/Duplex
Simplex
Video REC CH Number
Display Speed
1CH Mode, 4CH Mode
4 CH Realtime
Time Lapse,
REC Mode
Event(Alarm,Motion),
Schedule (Date/Time)
-64, -32, -16, -8,-4, -2, 1, 2, 4, 8, 16, 32, 64
Forward/Reverse
Play Speed
Frame Advance
REC/Play
/Searching
200hours(4CH Real time)
500hours(1CH Real time)
Time Lapse Mode :
Max 15000hours
Recording Capability
Time
Video Record Resolution
REC File Size
704 240
High : 14KB, Normal : 6KB,
Low : 3KB
*
Record Event, Alarm/Motion Event,
Power, Loss CH
Event List
Recod Event Search,
Alarm/Normal Event Search,
Date/Time Search
1(Terminal Jack), 4(RJ-11 DIY Camera)
1(Terminal Jack)
Search Mode
Input
Output
Alarm Reset
Pre Alarm
Duration
1(Terminal Jack)
OFF, 1sec, 2sec, 3sec, 4sec, 5sec
5sec ~ 59sec, 1M,2M ~ 30M
O
Alarm/Motion
Buzzer
Motion Det.
Motion Detection Level
Password
Remocon
HDD
9 area / CH
High, Middle, Low
on/off
Remocon
Storage
O
default 1EA
160G(MAX HDD SIZE : 250GB 2)
*
AC Input
Adapter
AC100 ~ 240, 2A, 50/60Hz
DC 12V, 4A
RJ-11 Jack, DC 12V,
Power
SET
Camera Power Output
4W
4
*
SHR-1040
SOC-C120
SOC-N120
1EA
X
X
1EA
2EA
2EA
Operation Temp.
32˚F ~ 104˚F
-4˚F ~ 140˚F
20% ~ 85% RH
20% ~ 85% RH
Preservation Temp.
Operation Humidity
Preservation Humidity
8.46(W) X 3.46(H) X 13.27(D),
(Packing) 17.95(W) X 7.20(H) X 13.30(D)
8.46(W) X 3.46(H) X 13.27(D)
(Packing) 17.95(W) X 11.5(H) X 13.3(D)
Size (INCH)
Weight (LBS)
6 lbs, (Packing) 9.26 lbs
6 lbs, (Packing) 17.42 lbs
9-1
English
Download from Www.Somanuals.com. All Manuals Search And Download.
2) SOC-C120 : Standard Camera
Model Name
SOC-C120
Broadcasting System
Imaging Device
Effective Pixels S
Synchronization
Resolution
NTSC STANDARD
1/4” SUPER HAD (Hole Accumulation Diode) IT CCD
510(H) x 492(V)
Internal
H :330 TV Lines, V: 350 TV Lines
VBS 1.0Vp-p(75ohms composite)
Signal Output
S/N Ratio
48 dB
Minimum Scene Illumination
Gamma Correction
Lens
2lux(F2.0, 50 IRE)
0.45
Focal Length (f) : 3.8 mm, F Number = 2.0
Electronic Shutter lris
-40dB Condenser Microphone Inclusion
Modular jack
Auto Exposure
Audio
I/O Connectors
Operating Temperature
Power Source
Power Consumption
Dimensions
+32 °F ~ +104 °F
DC 12V
Approx. 2W
2.25(W) x 1.86(H) x 3.95(L) inch
0.29 Ibs
Weight
9-3
9-2
English
Download from Www.Somanuals.com. All Manuals Search And Download.
SHR-1040/1040K USER’S MANUAL
3) SOC-N120 : Nightvision Camera
Model Name
SOC-N120
Product type
IR LED Day &Night Vision Camera
Voltage DC 12V from Equipment(DIY Monitor or DVR )
NTSC Standard Color Camera
1/4 inch IT S-HAD CCD
Power source
Brodcast System
Image Device
Effective Pixel
Scanning Method
510(H)x492(V)
525lines 2 : 1 Interlace
Horizontal : 15,734Hz
Vertical : 60Hz
Line Frequency
Weather Resist Grade
Synchronization Method
Resolution
IP43
INT
330TV lines
S/N Ratio
48dB
Light Condition
Light sensor Auto Switching IR LED Control 10pcs
Normal : 2 Lux
Night mode : IR LED ON
Minimum scene Illumination
Color Temperature
Elctronic shutter
Signal Output
ATW
ELC
Composite Video out 1.0Vp-p 75 ohms RJ11
Focal length : 3.8mm
Aperture(F) : F2.0
Lens
Operating Temperature
Operating Humidity
-10°C~ +50°C
~90%
Physical Size
Weight
2.51(W) X 2.44(H) X 4.92(L)inch
0.33 lbs
9-3
9-4
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Recommended HDD List
2
MAKER
MODEL
SV0802N
SV1604E
CAPACITY
80GB
REMARK
SAMSUNG
160GB
200GB
160GB
250GB
160GB
200GB
250GB
160GB
250GB
SV2041N
WD1600JB
WD2500JB
6L160PO
6L200PO
6L250RO
WesterN Digital
Maxtor
ST3160212ACE
ST3250823A
Attached model in shipment
Seagate
9-4
English
Download from Www.Somanuals.com. All Manuals Search And Download.
SHR-1040/1040K USER’S MANUAL
Outline Drawing
3
9-5
English
Download from Www.Somanuals.com. All Manuals Search And Download.
|