Samsung Clothes Dryer DV455 User Guide

DV455*

Gas and Electric Dryer

user manual

This manual is made with 100% recycled paper.

imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service or accessory

parts, please register your product at or contact

www.samsung.com/register

1-800-SAMSUNG (726-7864)

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd 1

2012-06-25

5:20:16

• Energy Saving

Samsung dryers are super energy eﬃcient. You can dry up to 3.31 pounds of laundry with

1kWh. Also, both the large capacity and Fuzzy Logic Control save energy by automatically

drying your clothes the most eﬃcient way.

• Easy Reversible Door

Our dryers will ﬁt just about anywhere and without a door conﬂict. The direction of our easy

reversible door can be changed easily and quickly.

• Pedestal with Storage Drawers

An optional 15” pedestal is available to raise the dryer for easier loading and unloading. It also

oﬀers a built-in storage drawer that can hold a 100 oz. bottle of detergent

• Stacking (MODEL NO: SK-5A/XAA)

Samsung’s Washer and Dryer can be stacked to maximize usable space.

The dryer legs need to be removed to stack the Washer and Dryer. You can purchase

an optional stacking kit from you Samsung retailer.

• 4-way Vent (electric model only : DV455*)

You can install the exhaust vent in the following four (4) positions: back, either side, bottom.

Features _3

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd Sec9:3

2012-06-25

5:21:02

Safety instructions

Congratulations on your new Samsung Dryer. This manual contains important

information on the installation, use, and care of your appliance. Please take the

time to read this manual to take full advantage of your dryer’s many beneﬁts and

features.

WHAT YOU NEED TO KNOW ABOUT SAFETY INSTRUCTIONS

Please read this manual thoroughly to ensure that you know how to operate the extensive features and

functions of your new appliance safely and eﬃciently. Retain the manual in a safe place near the appliance

for future reference. Use this appliance only for its intended purpose as described in this instruction manual.

The Warnings and Important Safety Instructions in this manual do not cover all possible conditions and

situations that may occur. It is your responsibility to use common sense, caution, and care when installing,

maintaining, or operating your dryer.

Always contact your manufacturer about problems or conditions you do not understand.

IMPORTANT SAFETY SYMBOLS AND PRECAUTIONS

What the icons and signs in this user manual mean:

Hazards or unsafe practices that may result in severe personal injury,

death and/or property damage. Follow the information in this manual

to minimize the risk of ﬁre or explosion or to prevent property damage,

personal injury, or death.

Do not store or use gasoline or other ﬂammable vapors and liquids near

this or any other appliance.

WARNING

Hazards or unsafe practices that may result in personal injury and/or

property damage.

CAUTION

Do NOT attempt.

Do NOT disassemble.

Do NOT touch.

Follow directions explicitly.

Unplug the power plug from the wall socket.

Make sure the machine is grounded to prevent electric shock.

Call the service center for help.

Note

These warning signs are here to prevent injury to you and others.

Please follow them explicitly.

After reading this section, keep it in a safe place for future reference.

SAVE THESE INSTRUCTIONS

4_ Safety instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd Sec11:4

2012-06-25

5:21:02

WARNING - Risk of Fire

•

Clothes dryer installation must be performed by a qualiﬁed installer.

Install the clothes dryer according to the manufacturer’s instructions and local codes.

Do not install a clothes dryer with ﬂexible plastic venting materials. If ﬂexible metal (foil type) duct

is installed, it must be of a speciﬁc type identiﬁed by the appliance manufacturer as suitable for

use with clothes dryers. Flexible venting materials are known to collapse, be easily crushed, and

trap lint. These conditions will obstruct clothes dryer airﬂow and increase the risk of ﬁre.

•

To reduce the risk of severe injury or death, follow all installation instructions.

TO REDUCE THE RISK OF FIRE OR EXPLOSION:

WARNING

•

Do not dry items that have been previously cleaned, washed, soaked, or spotted with

gasoline, dry cleaning solvents, or other ﬂammable or explosive substances. They emit

vapors that could ignite or explode. Any material that has been in contact with a cleaning

solvent or ﬂammable liquids or solids should not be placed in the dryer until all traces of

these ﬂammable liquids or solids and their fumes have been removed.

There are many highly ﬂammable items used in homes, such as acetone, denatured alcohol,

gasoline, kerosene, some liquid household cleaners, some spot removers, turpentine, waxes,

and wax removers

•

Do not dry items containing foam rubber (may be labeled latex foam) or similarly textured

rubber-like materials on a heat setting. Heated foam rubber materials can, under certain

circumstances, produce ﬁre by spontaneous combustion.

WHAT TO DO IF YOU SMELL GAS:

WARNING

•

Do not try to light any appliance.

Do not turn on the appliance.

Do not touch any electrical switch.

Do not use any phone in your building.

Clear the room, building or area of all occupants.

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s

instructions.

•

If you cannot reach your gas supplier, call the ﬁre department.

Installation and service must be performed by a qualiﬁed installer, service agency, or the gas

supplier.

SAVE THESE INSTRUCTIONS

Safety instructions _5

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd Sec11:5

2012-06-25

5:21:02

Safety instructions

WARNING

To reduce the risk of ﬁre, electric shock, or injury to persons when using your appliance, follow

basic precautions, including the following:

1. Read all instructions before using this appliance.

2. Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted

with gasoline, dry-cleaning solvents, or other ﬂammable or explosive substances, because

they give oﬀ vapors that could ignite or explode.

3. Do not use the dryer to dry clothes which have traces of any ﬂammable substance, such

as vegetable oil, cooking oil, machine oil, ﬂammable chemicals, thinner, etc., or anything

containing wax or chemicals, such as mops and cleaning cloths. Flammable substances may

cause the fabric to catch ﬁre by itself.

4. Do not store or use gasoline or other ﬂammable vapors and liquids near this or any other

appliance.

5. Do not allow children or pets to play on, in, or in front of the appliance. Close supervision is

necessary when the appliance is used near children and pets.

6. Before the appliance is removed from service or discarded, remove the door to the drying

compartment to prevent children or animals from becoming trapped inside.

7. Do not reach into the appliance when the drum is moving.

8. Do not install or store this appliance where it will be exposed to the weather.

9. Do not tamper with the controls.

10. Do not repair or replace any part of the appliance or attempt any servicing unless speciﬁcally

recommended in the user-maintenance instructions or published in the user-repair

instructions that you understand and have the skills to carry out.

11. Do not use fabric softeners or products to eliminate static unless recommended by the

manufacturer of the fabric softener or product.

12. Clean the lint screen before or after each load.

13. Do not use heat to dry articles containing foam rubber or similarly textured rubber-like

materials.

14. Keep the area around the exhaust opening and surrounding areas free from lint, dust, and

dirt.

15. The interior of the dryer and exhaust duct should be cleaned periodically by qualiﬁed service

personnel.

16. Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking

oils may contribute to a chemical reaction that could cause a load to catch ﬁre.

17. This appliance must be grounded. See “Electrical requirements” and ”Grounding” in the

“Installing your dryer” section.

18. This appliance must be properly grounded. Never plug the power cord into a receptacle

that is not grounded adequately and in accordance with local and national codes. Refer to

installation instructions for grounding this appliance.

SAVE THESE INSTRUCTIONS

6_ Safety instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd Sec11:6

2012-06-25

5:21:02

19. Ensure pockets are free from small irregularly shaped hard objects and foreign material, i.e.

coins, knives, pins, etc. These objects could damage your dryer.

20. Gas leaks may occur in your system, resulting in a dangerous situation.

21. Gas leaks may not be detected by smell alone.

22. Gas suppliers recommend you purchase and install a UL-approved gas detector.

STATE OF CALIFORNIA PROPOSITION 65 WARNINGS:

WARNING

The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California

to publish a list of substances known to the State of California to cause cancer, birth defects,

or other reproductive harm, and requires businesses to warn of potential exposure to such

substances.

This product contains a chemical known to the State of California to cause cancer, birth defects,

or other reproductive harm. This appliance can cause low-level exposure to some of the

substances listed, including benzene, formaldehyde, and carbon monoxide.

Gas appliances may cause low-level exposure to some of the substances listed including

benzene, formaldehyde, carbon monoxide, and soot; as a result of possible incomplete

combustion of natural gas or LP fuels. Exposure to these substances can be minimized further

by properly venting the dryer to the outdoors.

CAUTION

1. Do not sit on top of the dryer.

2. Because of continuing product improvements, Samsung reserves the right to change

speciﬁcations without notice. For complete details, see the Installation Instructions packed

with your product before selecting cabinetry, making cutouts, or beginning installation.

3. Do not wash clothing with large buckles, buttons, or other heavy metal or solid things.

4. Install and use in accordance with the manufacturer’s instructions.

5. Do not place items in your dryer that have been spotted or soaked with vegetable oil or

cooking oil. Even after being washed, these items may contain signiﬁcant amounts of these

oils.

6. Residual oil on clothing can ignite spontaneously. The potential for spontaneous combustion

increases when items containing vegetable oil or cooking oil are exposed to heat. Heat

sources such as your dryer can warm these items, allowing an oxidation reaction in the oil to

occur. Oxidation creates heat. If this heat cannot escape, the items can become hot enough

to catch ﬁre. Piling, stacking, or storing these kinds of items may prevent heat from escaping

and can create a ﬁre hazard.

7. All washed and unwashed fabrics that contain vegetable oil or cooking oil can be dangerous.

Washing these items in hot water with extra detergent will reduce, but not eliminate, the

hazard. Always use the Cool Down cycle for these items to reduce their temperature. Never

remove these items from the dryer hot or interrupt the drying cycle until the items have run

through the Cool Down cycle. Never pile or stack these items when they are hot.

8. Take care that children’s ﬁngers are not caught in the door when closing it. This may result in

injury.

SAVE THESE INSTRUCTIONS

Safety instructions _7

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd Sec11:7

2012-06-25

5:21:02

Safety instructions

REGULATORY NOTICE

1. FCC Notice

FCC CAUTION:

CAUTION

Any changes or modiﬁcations not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

This device complies with Part 15 of FCC Rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received including interference that causes

undesired operation.

For product available in the USA/Canada market, only channel 1~11 can be operated. Selection

of other channels is not possible.

FCC STATEMENT:

This equipment has been tested and found to comply within the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment oﬀ and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna

Increase the separation between the equipment and receiver

Connect the equipment to an outlet on a diﬀerent circuit from that of the receiver.

Consult the dealer or an experienced radio/TV technician for help.

FCC RADIATION EXPOSURE STATEMENT:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with a minimum distance of 20cm

between the radiator and your body. This device and its antenna(s) must not be co-located or

operated in conjunction with any other antenna or transmitter.

SAVE THESE INSTRUCTIONS

8_ Safety instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd Sec11:8

2012-06-25

5:21:02

2. IC Notice

The term “IC” before the radio certiﬁcation number only signiﬁes that Industry Canada technical

speciﬁcations were met. Operation is subject to the following two conditions: (1) this device may

not cause interference, and (2) this device must accept any interference, including interference

that may cause undesired operation of the device.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada.

For product available in the USA/Canada market, only channels 1~11 can be operated. Selection

of other channels is not possible.

IC RADIATION EXPOSURE STATEMENT:

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance of 20

cm between the radiator & your body. This device and its antenna(s) must not be co-located or

operated in conjunction with any other antenna or transmitter.

SAVE THESE INSTRUCTIONS

Safety instructions _9

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd Sec11:9

2012-06-25

5:21:02

contents

12 Unpacking your dryer

12 See exhaust requirements

13 Basic requirements

13 Ducting requirements

14 Important to installer

15 Location considerations

15 Alcove or closet installations

17 Mobile home installations

17 Exhausting

INSTALLING YOUR DRYER

18 Gas requirements

18 Commonwealth of massachusetts

installation instructions

19 Electrical requirements

19 Grounding

20 Electrical connections

21 Connecting the inlet hose

23 Replacement parts and accessories

23 Installation

26 Final installation checklist

26 Dryer exhaust tips

27 Door Reversal

29 Overview of the control panel

34 Rack Dry

OPERATING INSTRUCTIONS, TIPS

35 Clean the lint ﬁlter

35 Load the dryer properly

35 Getting started

36 Vent Sensor

37 Setting up Smart control and Smart

monitoring

40 Using the mobile app (Android)

52 Using the mobile app (iOS)

62 Registering your dryer

64 Control Panel

64 Tumbler

64 Stainless Steel Tumbler

64 Dryer Exterior

64 Dryer Exhaust System

^{CARE AND CL}6^EAN4^ING

10_ contents

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd Sec2:10

2012-06-25

5:21:02

65 Special laundry tips

^{SPECIAL LAUND}6^{RY T}5^IPS

^TROUBLESH6^OOT6^ING

66 Check these points if your dryer…

68 Information codes

69 Network Setup Q&A

71 Fabric care chart

APPENDIX

72 Protecting the environment

72 Declaration of conformity

72 Speciﬁcations

73 Cycle chart

74 Open Source Announcement

contents _11

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd Sec2:11

2012-06-25

5:21:03

Installing your dryer

UNPACKING YOUR DRYER

Unpack your Dryer and inspect it for shipping damage. Make sure you have received all the items

shown below. If your Dryer was damaged during shipping, or you do not have all the items, contact

1-800-SAMSUNG (726-7864).

To prevent personal injury or strain, wear protective gloves whenever lifting or carrying the unit.

The packing materials can be dangerous children. Keep all packaging material (plastic bags,

polystyrene, etc.) well out of the reach of children.

WARNING

SEE EXHAUST REQUIREMENTS

Top Cover

[ BACK ]

Control panel

Door

Filter

Water Inlet

Frame Front

Duct Exhaust

Parts supplied

“Y”-connector

Short inlet hose

Rubber Washer

Long inlet hose

12_ Installing your dryer

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd 12

2012-06-25

5:21:03

Tools needed

Pipe wrench

(gas only)

Pliers

Cutting knife

Nut drivers

Level

Phillips Screwdriver

Duct tape

Wrench

BASIC REQUIREMENTS

Make sure you have everything necessary for the proper installation

•

A GROUNDED ELECTRICAL OUTLET is required. Refer to the “Electrical requirements” section on

page 19.

•

A POWER CORD electric dryer (except for Canada).

GAS LINES (if a gas dryer) must meet national and local codes.

The EXHAUST SYSTEM must be made of rigid metal or ﬂexible stiﬀ-walled metal exhaust ducting.

DUCTING REQUIREMENTS

•

Use a 4-inch (10.2 cm) diameter rigid aluminum or rigid galvanized steel duct.

Do not use a smaller duct.

Ducts larger than 4 inches (10.2 cm) in diameter can result in increased accumulation of lint.

Lint should be removed regularly.

If a ﬂexible metal duct must be used, use the type with a stiﬀ sheet metal wall. Do not use a ﬂexible duct

with a thin foil wall. A serious blockage can result if the ﬂexible metal duct is bent too sharply.

•

Never install any type of ﬂexible duct in walls, ceilings, or other concealed spaces.

Keep the exhaust duct as straight and short as possible.

Secure joints with duct tape. Do not use screws.

Plastic ﬂexible ducts can kink, sag, be punctured, reduce airﬂow, extend drying times, and aﬀect the

dryer operation.

•

Exhaust systems longer than recommended can extend drying times, aﬀect machine operations, and

collect lint.

The exhaust duct should end with an exhaust hood with a swing-out damper to prevent back drafts and

entry of wildlife. Never use an exhaust hood with a magnetic damper.

The hood should have at least 12 inches (30.5 cm) of clearance between the bottom of the hood and

the ground or other obstruction. The hood opening should point down.

•

Never install a screen over the exhaust outlet.

To avoid lint buildup, do not exhaust the dryer directly into a window well. Do not exhaust under a house

or porch.

•

If the exhaust duct must run through an unheated area, the duct should be insulated and slope slightly

down towards the exhaust hood to reduce condensation and lint buildup.

Installing your dryer _13

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd 13

2012-06-25

5:21:03

Installing your dryer

•

Inspect and clean the interior of the exhaust system at least once a year. Unplug the power cord before

cleaning.

•

Check frequently to make sure the exhaust hood damper opens and closes freely.

Check once per month, and clean at least once per year. Note: If your clothes are not getting dry, then

check the ducting for obstructions.

•

Do not exhaust the dryer into a wall, ceiling, crawl space, or concealed space of a building, gas vent, or

any other common duct or chimney. This could create a ﬁre hazard from the lint expelled by the dryer.

ELECTRIC AND GAS DRYER

Weather Hood Type

Use only for short-run installation

Recommended

4” (10 .16 cm)

2.5” (6.35 cm)

No. of 90° elbows

Rigid

Metallic Flexible*

10.1 m (33 ft.)

8.8 m (29 ft.)

7.6 m (25 ft.)

6.5 m (21 ft.)

Rigid

Metallic Flexible*

12.4 m (41 ft.)

11.2 m (37 ft.)

10.1 m (33 ft.)

9.0 m (29 ft.)

22.6 m (74 ft.)

18.9 m (62 ft.)

15.5 m (51 ft.)

12.5 m (41 ft.)

24.4 m (80 ft.)

20.7 m (68 ft.)

17.4 m (57 ft.)

14.3 m (47 ft.)

* Do not use non-metallic ﬂexible ducts.

If the new dryer is installed into an existing exhaust system you must make sure:

•

The exhaust system meets all local, state, and national codes.

That a ﬂexible plastic duct is not used.

To inspect and clean all lint buildup from inside the existing duct.

The duct is not dented or crushed.

The exhaust hood damper opens and closes freely.

The static pressure in any exhaust system must not exceed 0.83 inches of water column, or be less than 0.

This can be measured with the dryer running with a manometer at the point where the exhaust duct

connects to the dryer. A no-heat setting should be used. The dryer tumbler should be empty and the lint

ﬁlter clean.

IMPORTANT TO INSTALLER

Please read the following instructions carefully before installing the dryer. These instructions should be kept

for future reference.

Remove the door from all discarded appliances to avoid the danger of a child being trapped and

suﬀocating.

WARNING

14_ Installing your dryer

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd 14

2012-06-25

5:21:03

LOCATION CONSIDERATIONS

The dryer should be located where there is enough space at the front for loading the dryer, and enough

space behind for the exhaust system. This dryer is factory-ready for the rear exhaust option. To exhaust out

the bottom, right or the left, use the accessory exhaust kit. Instructions are included with the kit. Make sure

the room in which the dryer is located has enough fresh air. The dryer must be located where there are no

air-ﬂow obstructions.

For gas dryers, adequate clearance must be maintained as noted on the data plate to ensure adequate air

for combustion and the proper dryer operation.

The dryer must not be installed or stored in an area where it will be exposed to water and/or weather. The

dryer area must be kept clear of combustible materials, gasoline, and other ﬂammable vapors and liquids. A

dryer produces combustible lint. The area around the dryer should be kept lint-free.

ALCOVE OR CLOSET INSTALLATIONS

The dryer must be exhausted to the outside to reduce the risk of ﬁre when installed in an alcove or

closet.

WARNING

•

No other fuel-burning appliance should be installed in the same closet as the dryer.

WARNING: To reduce the risk of ﬁre, this dryer must be exhausted to the outside. Refer to the

“Exhausting” section on page 17.

Minimum clearances between the dryer and adjacent walls or other

surfaces

Sides

Top

1 in / 25 mm

Rear

Front

5 in / 127 mm

2 in / 51 mm

17 in / 432 mm

•

The front of the closet must have two unobstructed air openings for a combined minimum

total area of 72 in² (465 cm²) with a minimum clearance of 3” (7.6 cm) at the top and bottom.

A slatted door with equivalent space clearances is acceptable.

Recessed area

Side view - closet or conﬁned area

1 in.

(2.5 cm)

17 in.

(43.2 cm)

1 in.

(2.5 cm)

27 in.

(68.6 cm)

27 in.

(68.6 cm)

1 in.

(2.5 cm)

2 in.

(5 cm)

34.1 in.

(86.5 cm)

5 in.

(12.7 cm)

Installing your dryer _15

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd 15

2012-06-25

5:21:04

Installing your dryer

With optional pedestal base or stacking kit

Required Dimensions for Installation

With Stacking Kit

Required Dimensions for Installation With Pedestal

51.2 in. (130 cm) to clear open door

39 in.

(99 cm)

6 in. *

(15.2 cm)

53.6 in.

(136.2 cm)

34.1 in.

(86.5 cm) (12.7 cm)

5 in.

27 in.

(68.6 cm)

3 in.

(7.6 cm)

2.5 in.

(6.3 cm)

77.2 in.

(196.2 cm)

48 in.² *

(310 cm²)

Closet or Door

1 in.

(2.5 cm)

27 in.

(68.6 cm)

24 in.² *

(155 cm²)

3 in.

(7.6 cm)

1 in.

34.1 in.

5.9 in.**

(2.5 cm) (86.5 cm) (15 cm)

* Required spacing

** An external exhaust elbow requires additional space.

It is not recommended to stack DV457* on your washer.

(it might be hard to control dryer LCD because of the viewing angle.)

16_ Installing your dryer

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd 16

2012-06-25

5:21:04

MOBILE HOME INSTALLATIONS

The installation of the dryer in a mobile home must conform to the Manufactured Home Construction and

Safety Standards Title 24 CFR, Part 3280 {formerly the Federal Standards for Mobile Home Construction

and Safety, Title 24, HUD (Part 280), 1975} for the United States) or CSA Standards Z240 (for Canada).

•

When installing a dryer in a mobile home, provisions for anchoring the dryer to the ﬂoor must be made.

Locate an area with adequate fresh air.

A minimum unobstructed space of 72 in² (465 cm²) is required.

Call 1-800-SAMSUNG for information on purchasing the Floor Anchoring Kit as an accessory.

All mobile home installations must be exhausted to the outside with the exhaust duct termination

securely fastened to the mobile home structure, using materials that will not combust.

•

The exhaust duct may not terminate underneath the mobile home.

Refer to the following “Exhausting” section for more information.

EXHAUSTING

The dryer shall not be exhausted into a chimney, a wall, a ceiling, an attic, a crawl space, or a concealed

space of a building.

Exhausting the dryer to the outside will prevent large amounts of lint and moisture from being blown into the

room.

Refer to the “Ducting requirements” section on page 13 for the maximum duct length and

number of bends.

•

All dryers must be exhausted to the outside.

Do not assemble the duct with screws or other fastening means that extend into the

duct and catch lint.

•

The exhaust duct should be 4 inches (102 mm) in diameter.

The total length of ﬂexible metal duct shall not exceed 2.4 m (7.8 ft.).

In the United States:

•

Use only those foil-type ﬂexible ducts, if any, speciﬁcally identiﬁed for use with the appliance

by the manufacturer and that comply with the Outline for Clothes Dryer Transition Ducts,

Subject 2158A, shall be used.

In Canada:

•

Use only those foil-type ﬂexible ducts, if any, speciﬁcally identiﬁed for use with the appliance

by the manufacturer.

Outside the U.S. and Canada:

•

Refer to the local codes.

The dryer must be exhausted to the outside to reduce the risk of ﬁre when installed in an

alcove or closet.

WARNING

NEVER USE A PLASTIC OR NON-METAL FLEXIBLE DUCT.

If your existing ductwork is plastic, non-metal, or combustible, replace it with metal.

Use only a metal exhaust duct that is non-ﬂammable to ensure containment of the exhaust

air, heat, and lint.

WARNING

Installing your dryer _17

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd 17

2012-06-25

5:21:04

Installing your dryer

GAS REQUIREMENTS

Use only natural or LP (liquid propane) gases.

THE INSTALLATION MUST CONFORM WITH LOCAL CODES, OR IN THE ABSENCE OF LOCAL

CODES, WITH THE NATIONAL FUEL GAS CODE ANSI/Z223.1, LATEST REVISION (FOR THE UNITED

STATES), OR WITH THE CAN/CGA-B149 INSTALLATION CODES (FOR CANADA).

Gas dryers are equipped with a burner vent for use with natural gas. If you plan to use your dryer with LP

(liquid propane) gas, it must be converted for safe and proper performance by a qualiﬁed service technician.

A 1/2” (1.27 cm) gas supply line is recommended and must be reduced to connect to the 3/8” (1 cm) gas

line on your dryer. The National Fuel Gas Code requires that an accessible, approved manual gas shut-oﬀ

valve be installed within 6” of your dryer.

Gas dryers installed in residential garages must be raised 18 inches (46 cm) above the ﬂoor.

Additionally, a 1/8” (0.3 cm) N.P.T. (National Pipe Thread) plugged tapping, accessible for test gauge

connection, must be installed immediately upstream of your dryer’s gas supply connection.

Your dryer must be disconnected from the gas supply pipe system during any pressure testing of the

system.

DO NOT reuse old ﬂexible metal gas lines. Flexible gas lines must be design certiﬁed by the American Gas

Association (CGA in Canada).

•

Any pipe joint compound used must be resistant to the action of any liqueﬁed petroleum gas.

As a courtesy, most local gas utilities will inspect a gas appliance installation.

GAS IGNITION - Your dryer uses an automatic ignition system to ignite the burner.

There is no constant burning pilot.

COMMONWEALTH OF MASSACHUSETTS INSTALLATION

INSTRUCTIONS

Your dryer must be installed by a licensed plumber or gas ﬁtter. A “T” handle manual gas valve must be

installed in the gas supply line to your dryer. If a ﬂexible gas connector is used to install your dryer, the

connector may not be longer than 3’ (36”).

•

Gas leaks may occur in your system, creating a dangerous situation.

Gas leaks may not be detected by smell alone.

Gas suppliers recommend that you purchase and install a UL-approved gas detector.

Install and use it in accordance with the manufacturer’s instructions.

WARNING

18_ Installing your dryer

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd 18

2012-06-25

5:21:04

ELECTRICAL REQUIREMENTS

The wiring diagram is located on the plate below the control panel.

•

The improper connection of the equipment grounding conductor can result in a risk of electric

shock. Check with a qualiﬁed electrician or serviceman if you are in doubt as to whether your dryer

is properly grounded. Do not modify the plug provided with your dryer - if it doesn’t ﬁt the outlet,

have a proper outlet installed by a qualiﬁed electrician.

WARNING

•

To prevent unnecessary risk of ﬁre, electrical shock, or personal injury, all wiring and grounding

must be done in accordance with local codes, or in the absence of local codes, with the National

Electrical Code, ANSI/NFPA No. 70-Latest Revision (for the U.S.) or the Canadian Electrical Code

CSA C22.1 - Latest Revisions and local codes and ordinances. It is your responsibility to provide

adequate electrical services for your dryer.

•

All gas installations must be done in accordance with the national Fuel Code ANSI/Z2231 - Latest

Revision (for the U.S.) or CAN/CGA - B149 Installation Codes - Latest Revision (for Canada) and

local codes and ordinances.

GROUNDING

This dryer must be grounded. In the event of a malfunction or breakdown, the grounding the product will

reduce the risk of electrical shock by providing a path of least resistance for the electrical current.

Gas models

WARNING

Your dryer has a cord with an equipment-grounding conductor and a grounding plug.

The plug must be plugged into an appropriate outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

Do not modify the plug provided with your dryer – if it doesn’t ﬁt the outlet, have a proper outlet

installed by a qualiﬁed electrician.

Never connect the ground wire to the plastic plumbing lines, gas lines, or hot water pipes.

Electric models

WARNING

Your dryer has an optional cord with an equipment-grounding conductor and a grounding plug,

which is sold separately.

The plug must be plugged into an appropriate outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

Do not modify the plug provided with your dryer – if it doesn’t ﬁt the outlet, have a proper outlet

installed by a qualiﬁed electrician.

If a power cord is not used and the electric dryer is to be permanently wired, the dryer must

be connected to a permanently grounded metal wiring system, or an equipment grounding

conductor must be run with the circuit conductors and connected to the equipment grounding

terminal or lead on the dryer.

Installing your dryer _19

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd 19

2012-06-25

5:21:04

Installing your dryer

ELECTRICAL CONNECTIONS

Before operating or testing, follow all grounding instructions in the “Grounding” section on page 19.

An individual branch (or separate) circuit serving only your dryer is recommended. DO NOT USE AN

EXTENSION CORD.

Gas models – U.S. and Canada

A 120 volt, 60 Hz AC approved electrical service, with a 15-ampere fuse or circuit breaker is

required.

Electric models – U.S. only

Most U.S. dryers require a 120/240 volt, 60 Hz AC approved electrical service. Some require

120/208 volt, 60 Hz approved electrical service. The electric service requirements can be found

on the data label located behind the door. A 30-ampere fuse or circuit breaker on both sides of

the line is required.

•

If a power cord is used, the cord should be plugged into a 30-ampere receptacle.

The power cord is NOT provided with U.S. electric model dryers.

RISK OF ELECTRIC SHOCK:

When local codes allow, the electrical supply of the dryer may be connected by means of

WARNING

a new power supply cord kit, marked for use with a dryer, that is U.L. listed and rated at a

minimum of120/240 volts, 30-ampere with three No. 10 copper wire conductors terminated

with closed loop terminals, open-end spade lugs with turned up ends, or with tinned leads.

•

Do not reuse a power supply cord from an old dryer. The power cord electric supply

wiring must be retained at the dryer cabinet with a suitable UL-listed strain relief.

Grounding through the neutral conductor is prohibited for (1) new branch-circuit

installations, (2) mobile homes, (3) recreational vehicles, and (4) areas where local

codes prohibit grounding through the neutral conductor. (Use a 4-prong plug for 4 wire

receptacles, NEMA type 14-30R.)

•

Electric models – Canada Only

•

A 120/240 volt, 60 Hz AC approved electrical service fused through a 30-ampere fuse or

circuit breaker on both sides of the line is required.

•

All Canadian models are shipped with the power cord attached. The power cord should be

plugged into a 30-ampere receptacle.

In Canada, you may not convert a dryer to 208 volts.

20_ Installing your dryer

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd 20

2012-06-25

5:21:04

CONNECTING THE INLET HOSE

Method 1

The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old

hoses.

1. If space permits, attach the brass female end of the “Y”

connector to the cold water faucet.

2. Turn the cold water faucet oﬀ.

Y-Connector

3. Attach the straight end of long hose to the “Y’ connector.

4. Using pliers, tighten the coupling with an additional two-

thirds turn.

Water Hose

Do not overtighten, as this may damage the coupling.

5. Attach the angled end of long hoses to ﬁll the valve at the

Duct Exhaust

bottom of the dryer’s rear frame. Screw on the coupling by

hand until it is seated on the ﬁll valve connector.

6. Using the pliers, tighten the coupling with an additional two-

Frame

(back)

thirds turn.

Do not overtighten, as this may damage the coupling.

7. Check that the water faucets are on.

8. Check for leaks around the “Y” connector, faucets and

hoses.

Water Hose

Installing your dryer _21

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd 21

2012-06-25

5:21:04

Installing your dryer

Method 2

The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old

hoses.

1. If the “Y” connector cannot be attached directly to the cold

water faucet, the short hose must be used.

2. Turn the cold water faucet oﬀ.

Short hose

(Inlet to cold

water)

3. Attach the short inlet hose to the cold water faucet.

Screw on the coupling by hand until it is seated on the

faucet.

“Y” connector

4. Using the pliers, tighten the coupling with an additional two-

thirds turn.

Long hose

Duct Exhaust

Do not overtighten, as this may damage the coupling.

5. Attach the ‘Y” connector to the brass male end of the small

hose. Screw on the coupling by hand until it is seated on the

connector.

Frame

(back)

6. Using the pliers, tighten the coupling with an additional two-

thirds turn.

Do not overtighten, as this may damage the coupling.

7. Attach the angled end of long hoses to the ﬁll valve at the

bottom of the dryer rear frame. Screw on the coupling by

hand until it is seated on the ﬁll valve connector.

Water Hose

8. Using pliers, tighten the coupling with an additional two-

thirds turn.

Do not overtighten, as this may damage the coupling.

9. Attach the washer hose to the other side of the “Y”

connector. Screw on the hose coupling until it is tight. Using

pliers, tighten the coupling with an additional two thirds turn.

Do not overtighten. You can damage the coupling.

10. Check that the water faucets are on.

11. Check for leaks around the “Y” connector, faucets and

hoses.

22_ Installing your dryer

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd 22

2012-06-25

5:21:05

REPLACEMENT PARTS AND ACCESSORIES

If your dryer requires replacement parts or accessories, contact the dealer where you purchased your dryer

or the SAMSUNG customer care center at 1-800-SAMSUNG (726-7864).

INSTALLATION

For the proper installation, we recommend that you hire a qualiﬁed installer.

To install

1. Move your dryer to an appropriate location for the

Level

installation. Consider installing the dryer and washer side-

by-side, to allow access to the gas, electrical, and exhaust

connections. Place two of the carton cushion-tops on the

ﬂoor. Tip your dryer on its side so it lies across both cushion-

tops.

2. Set your dryer back in an upright position.

3. To ensure that the dryer provides the optimal drying

performance, it must be level. To minimize vibrations, noise,

and unwanted movement, the ﬂoor must be a perfectly level,

solid surface.

To set the dryer to the same height as the washer,

fully retract the leveling feet by turning them

counterclockwise, then loosen the legs by turning them

clockwise.

Leveling feet

Retract fully

Then loosen

Adjust the leveling feet only as much as necessary to

level the dryer. Extending the leveling feet more than

necessary can cause the dryer to vibrate.

4. Review the “Exhausting” section on page 17 before installing the exhaust system. Install the

ductwork from your dryer to the exhaust hood. The crimped end of the duct sections must

point away from your dryer.

DO NOT use sheet metal screws when assembling the ducting. These joints should be

taped.

Never use plastic ﬂexible exhaust material.

Tip for tight installations: install a section of the exhaust system onto your dryer before putting

it in place.

Use duct tape to secure this section to your dryer, but do not cover the ventilation slots at

the back of the unit in dryer cabinet.

Installing your dryer _23

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd 23

2012-06-25

5:21:05

Installing your dryer

5. Review the “Electrical requirements” section on page 19.

BEFORE OPERATING OR TESTING, follow the grounding instructions in the “Grounding”

section on page 19.

U.S. MODELS:

RISK OF ELECTRIC SHOCK - All U.S. models are produced for a 3-WIRE SYSTEM

WARNING

CONNECTION.

The dryer frame is grounded to the neutral conductor at the terminal block.

A 4-WIRE SYSTEM CONNECTION is required for new or remodeled construction,

mobile homes, or if local codes do not permit grounding through neutral. If the 4-wire

system is used, the dryer frame cannot be grounded to the neutral conductor at

the terminal block. Refer to the following instructions for 3 and 4-WIRE SYSTEM

CONNECTIONS.

Remove the terminal block cover plate.

Insert the power cord with a UL-listed strain relief through the hole provided in the cabinet

near the terminal block.

A strain relief must be used.

Do not loosen the nuts already installed on the terminal block. Be sure they are tight.

Use a 3/8” (1 cm) deep well socket.

6. Review the “Gas requirements” section on page 18. Remove the pipe thread protective

cap. Apply a pipe joint compound or about 1 1/2 wraps of Teﬂon tape over all threaded

connections.

The pipe joint compound must be resistant to the actions of any liqueﬁed petroleum

gas.

Connect the gas supply to your dryer. An additional ﬁtting is required to connect the 3/4” (1.9

cm) female thread end of a ﬂexible connector to the 3/8” (1 cm) male threaded end on the

dryer.

Securely tighten the gas line ﬁtting over the threads.

Turn on the gas supply.

Check all gas connections for leaks using a soap solution.

If bubbles appear, tighten the connections and recheck. DO NOT use an open ﬂame to

check for gas leaks.

24_ Installing your dryer

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd 24

2012-06-25

5:21:05

3-WIRE system connections

1. Loosen or remove the center terminal block screw.

2. Connect the neutral wire (white or center wire) of the power cord to the center, silver-colored

terminal screw of the terminal block. Tighten the screw.

3. Connect the other wires to the outer terminal block screws. Tighten the screws.

4. Tighten the strain relief screws.

5. Insert the tab of the terminal block cover into your dryer’s rear panel slot.

6. Secure the cover with a hold-down screw.

External ground connector

Neutral grounding wire (green/yellow)

Center silver-colored terminal block screw

Neutral wire (white or center wire)

3/4” (1.9 cm) UL-listed strain relief

If converting from a 4-wire electrical system to a 3-wire, the ground strap must be

reconnected to the terminal block support to ground the dryer frame to the neutral

conductor.

WARNING

4-WIRE system connections

1. Remove the center terminal block screw.

2. Connect the ground wire (green or unwrapped) of the power cord to the external ground

conductor screw.

3. Connect the neutral wire (white or center wire) of the power cord and the appliance ground

wire (green with yellow stripes) under the central screw of the terminal block.

4. Connect the other wires to the outer terminal block screws. Tighten the screws.

5. Tighten the strain relief screws.

6. Insert the tab of the terminal block cover into your dryer’s rear panel slot.

7. Secure the cover with a hold-down screw.

External ground connector

Green or bare copper wire of the power cord

3/4 in. (1.9 cm) UL-listed strain relief

Center silver-colored terminal block screw

Grounding wire (green/yellow)

Neutral wire (white or center wire)

8. With a level, check your dryer and make the necessary adjustments to the leveling legs.

9. At this time, make sure all gas connections (on gas models), exhaust and electrical

connections are complete. Plug in your dryer, and check its operation by using the checklist

below.

10. (GAS MODELS ONLY)

The burner may not ignite initially due to air in the gas line. Allowing your dryer to operate on

a heat setting will purge the line. If the gas does not ignite within 5 minutes, turn your dryer

oﬀ and wait 5 minutes. Be sure the gas supply to your dryer has been turned on. In order to

conﬁrm the gas ignition, check the exhaust for heat.

Installing your dryer _25

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd 25

2012-06-25

5:21:05

Installing your dryer

FINAL INSTALLATION CHECKLIST

•

the dryer is plugged into an electrical outlet and is properly grounded.

The exhaust ductwork is hooked up and the joints are taped.

A plastic ﬂexible duct is NOT used.

Use rigid or stiﬀ-walled ﬂexible metal vent material.

The dryer is level and is sitting ﬁrmly on the ﬂoor.

Gas models – the gas is turned on with no gas leaks.

Start your dryer to conﬁrm that it runs, heats, and shuts oﬀ.

DRYER EXHAUST TIPS

A plastic or non-metal ﬂexible duct presents a potential ﬁre hazard.

WARNING

1. Make sure your dryer is installed properly so it exhausts air

Wall

Dryer

easily.

Duct

Exhaust

2. Use a 4” diameter rigid metal duct. Tape all joints, including

4”

Tape

at the dryer. Never use lint-trapping screws.

Duct

3. Keep ducts as straight as possible.

4. Clean all old ducts before installing your new dryer. Be sure

the vent ﬂap opens and closes freely. Inspect and clean the

exhaust system annually.

Don’t let a poor exhaust system slow the drying process by:

•

Restricting your

dryer with a poor

exhaust system.

•

Using a plastic, thin

foil, or non-metal

ﬂexible duct.

•

Unnecessarily using

long ducts that have

many elbows.

•

Allowing dented or

clogged ducts and

vent.

26_ Installing your dryer

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd 26

2012-06-25

5:21:05

DOOR REVERSAL

1. Unplug the power cord.

2. Remove two door hinge screws.

3. Lift the door and remove it.

4. Remove two screws from the frame front.

5. Remove the two screws from the opposite side of the door

hinge.

6. Remove the two screws from the holder lever.

7. Reassemble the two screws on the inside holes.

8. Remove a screw from the door hinge.

The screw is for pre-ﬁxing the door to the frame front.

Installing your dryer _27

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd 27

2012-06-25

5:21:06

Installing your dryer

9. Reassemble the screw in the other hole.

10. Place the door on the other side and reattach it to the dryer.

11. Reattach the holder lever.

12. Reattach the screws in the remaining holes.

28_ Installing your dryer

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd 28

2012-06-25

5:21:06

Operating instructions, tips

To reduce the risk of ﬁ re, electric shock, or injury to persons,read the IMPORTANT SAFETY

INSTRUCTIONS before operating this appliance.

WARNING

OVERVIEW OF THE CONTROL PANEL

To select a cycle, rotate the Cycle Selector dial to the desired cycle.

The indicator light by the cycle name will illuminate. The Wool, Delicates,

Sanitize, Bedding PLUS, Heavy Duty, Normal, Eco Normal and Perm Press

cycles are Sensor Dry cycles.

Sensor Dry automatically senses the moisture in the load and shuts the dryer

oﬀ when the selected dryness level (very dry to damp dry) is reached.

Eco Normal - This cycle reduces energy usage by up to 15% compared

to the Normal Dry cycle. It adjusts the cycle time and temperature for

increased eﬃciency.

Normal - Use this cycle to dry loads such as cotton, underwear, and linen.

Heavy Duty - Use this cycle to get high heat for heavy fabrics such as jeans,

corduroys, or work clothes.

Perm Press - Dry wrinkle-free cottons, synthetic fabrics, knits, and permanent

press fabrics automatically.

Bedding PLUS - For bulky items such as blankets, sheets, and comforters.

Cycle Selector

Delicates - The Delicates cycle is designed to dry heat-sensitive items at a

low drying temperature.

Wool - For machine washable and tumble dryable wool only.

Load should be under 3 pounds. The Wool cycle of this machine

has been approved by Woolmark company for Total-Easy-Care

Wool products, M0913(DV455E*) and M1007(DV455G*).

Sanitize - Sanitize garments by infusing high temperature heat deep into

the fabric during the drying cycle. Use this course to keep your bedding and

curtains clean through sanitization.

Time Dry - Time Dry allows you to select the desired cycle time in minutes.

Turn the Cycle Selector dial to Time Dry, then press the Adjust Time up arrow

to set the drying time. Press the arrow repeatedly to scroll through the time

settings.

Operating instructions, tips _29

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd Sec3:29

2012-06-25

5:21:06

Operating instructions, tips

Quick Dry - Provides a 30 minutes drying cycle.

Air Fluﬀ - The Air Fluﬀ cycle tumbles the load in room temperature air.

Refresh - This cycle is best for smoothing out wrinkles and reducing odors

from loads consisting of one to four dry items. In this cycle a small amount

of water is sprayed into the dryer drum after several minutes of tumbling with

heat.

Wrinkle Away - The Wrinkle Away cycle removes wrinkles from clothes stored

in closets, etc. It provides wrinkle release via optimized steam care. You can

change the drying time.(Minimum time : 20 minutes) *For best results, load no

more than 3 items.

Overloading the dryer may not yield the same results.

The display window shows the estimated time remaining in the cycle after the

Start/Pause button is pressed. The estimated time remaining may ﬂuctuate as

the cycle progresses.

The Drying light will illuminate and remain lit until the cycle is complete.

When your dryer is in the cool-down phase, the Cooling light will illuminate.

LED Display

When your dryer is in the wrinkle prevent phase, the Wrinkle Prevent light will

illuminate.

When the cycle is complete, “End” will appear in the display panel until the

dryer door is opened or the Power button is pushed.

If your dryer is paused during a cycle, the indicator lights will blink until the

Start/ Pause button is pressed.

To select the dry level in the Normal, Heavy Duty, or other Sensor Dry cycles,

press the Dry Level button. An indicator light will illuminate next to the desired

dryness level.

Dry Level

Press the button repeatedly to scroll through the settings. Larger or bulkier

Selection Button loads may require the Very Dry or More Dry setting for complete dryness.

The Less Dry setting is best suited for lightweight fabrics or for leaving some

moisture in the clothing at the end of the cycle. Damp Dry is designed to

partially dry items. Use for items that lay ﬂat or hang to dry.

To select the correct temperature for the load, press the Temp button. An

indicator light will illuminate next to the desired temperature. Press the button

repeatedly to scroll through the settings.

High – For sturdy cottons or those labeled Tumble Dry.

Medium – For permanent press, synthetics, lightweight cottons, or items

labeled Tumble Dry Medium.

Temp Selection

Button

Med Low – For lower heat than Medium to dry synthetic or washable knit

fabrics.

Low – For heat sensitive items labeled Tumble Dry Low or Tumble Dry Warm.

Extra Low – Provides the lowest heated dry temperature possible.

When using Manual Dry cycles, you can adjust the drying time by pressing the

Time selection button.

During the Sensor Dry cycle, the time light indicator is oﬀ because exact

drying times are determined by ﬂuctuating humidity levels.

Time Selection

Button

30_ Operating instructions, tips

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd Sec3:30

2012-06-25

5:21:07

When the cycle is complete, a chime will sound.

If you selected the Wrinkle Prevent option, the chime will sound intermittently.

Adjust the volume of the chime or turn it oﬀ by pressing the Signal button.

Press the button repeatedly to scroll through the choices.

Signal Selection

Button

Any cycle can be delayed for up to 24 hours in one-hour increments.

Displayed hour indicates the time at which the cycle will be started. (Refer to

the “Delay Start” section on page 32.)

Delay Start

Button

Adjust Time – Time can be added or subtracted from the automatically set

times in the Manual Dry cycles (Time Dry, Quick Dry, or Air Fluﬀ cycles) and

Wrinkle Away cycle.

To add or subtract time from the cycle, press the Adjust Time arrow pad up or

down until the desired time is displayed.

Wrinkle Prevent -Wrinkle Prevent provides approximately 180 minutes

of intermittent tumbling in unheated air at the end of the cycle to reduce

wrinkling. Press the Wrinkle Prevent button to activate this feature.

The indicator light above the pad will illuminate when Wrinkle Prevent is

selected.

Select Cycle

Option

The load is dry, and can be removed at any time during the Wrinkle Prevent

cycle.

My Cycle – Choose your favorite cycle including cycle, temp, dry level option,

etc. (Refer to the “My cycle” section on page 33.)

Rack Dry – Rack Dry is available in the Time Dry cycle. Temperature will be

set to Extra Low only. (Refer to the “Rack Dry” section on page 34.)

Mixed Load Bell - This is an alarm that notiﬁes you when the average dry

level is damp dry (80% dried). This is useful when the laundry contains various

types of clothing you do not want to dry completely. An alarm sounds for 5

seconds. Note that the dryer will continue to run unless you pause or stop it.

This function can only be selected in the Sensor Dry course, and the dry level

can only be selected from among Normal Dry, More Dry, and Very Dry.

Start/Pause

selection button

Press to pause and restart programs.

Press once to turn your dryer on. Press again to turn it oﬀ. If your dryer is left

on for more than 10 minutes without any buttons being touched, the power

automatically turns oﬀ.

Power button

Operating instructions, tips _31

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd Sec3:31

2012-06-25

5:21:07

Operating instructions, tips

Child lock

Prevents children from playing with your dryer.

Setting/Releasing

To turn Child Lock on or oﬀ, press both the Temp. and Time buttons simultaneously for 3

seconds.

Child Lock Details

1. You can turn Child Lock on while your dryer is running.

2. Once you set the Child Lock function, no button, except for the Power button, will respond

until you turn oﬀ the Child Lock function.

3. The “Child Lock ” indicator will be lit.

•

If the dryer is powered on again, the Child Lock function stays on.

To turn oﬀ Child Lock, follow the instructions above.

When other buttons, except for the Power button, do not respond, check the Child Lock

indicator. If Child Lock is on, follow the instructions above to turn Child Lock oﬀ.

Delay Start

You can set the dryer to start your course automatically at a later time by choosing a delay time.

The hour displayed indicates the time at which the course will be started.

1. Set your drying course.

2. Press the Delay Start button repeatedly until the delay time is set.

3. Press the Start/Pause button. The “Delay Start

” indicator will be lit, and the clock will

begin counting down until it reaches the set time.

4. To cancel a Delay Start function, press the Power button and then turn the dryer on again.

Drum Light

Lights the dryer drum while the dryer is running.

Turning On and Oﬀ

To turn on or turn oﬀ the Drum Light, press both the Dry Level and Temp. buttons

simultaneously.

You can turn the Drum Light on and oﬀ while your dryer is running and when it is stopped.

If you do not turn the Drum Light oﬀ 5 minutes after turning it on, the Drum Light is

automatically turned oﬀ.

32_ Operating instructions, tips

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd Sec3:32

2012-06-25

5:21:07

My cycle

Lets you select, save, and then activate a customized cycle that includes Dry Level , Temp, Time

option, etc. at a later time.

To use My Cycle, follow these steps:

1. Push the My Cycle button. The My Cycle indicator lights.

2. Select the cycle you want to include using the Cycle Selector Dial.

3. Select and set the options (Dry Level, Temp, Time, etc.)

Each cycle has certain default options that are automatically set. To see these default

options, go to page 37.

4. Push the Start/Pause button. The cycle starts.

5. As the dryer moves through the cycle, it memorizes the cycle and the options.

6. To run this cycle again at a later time, press the My Cycle button. The dryer automatically

selects the saved cycle and options.

You can change the My Cycle settings by repeating the process above.

The dryer will use these settings the next time you choose My Cycle.

Smart Care

This function enables you to check the status of the dryer using a smartphone.

1. Press and hold the Time and Delay Start buttons for 3

seconds when an error occurs or if you haven’t pressed

any buttons on the dryer after you turned the power on.

2. When the Smart Care function is activated, the LED on the

window display rotates for 2 or 3 seconds and then the

error code will appear in the display panel.

3. Run the Smart Care app on your smart phone.

The Smart Care function is optimized with Galaxy S,

Galaxy S2, iPhone 4 and iPhone 4S.

4. If the smart phone’s camera is focused on the display panel

of the dryer, the panel and error message is automatically

recognized and the error type and countermeasures are

displayed on the smart phone.

5. If the smartphone fails to recognize the error code more

than twice, please enter the error code displayed on the

display panel of the dryer manually into the Smart Care

app.

Downloading the Smart Care app

Download the Samsung Laundry App into your mobile phone from the Android market or

Apple App store. (Search word :Samsung Smart Washer/Dryer)

Precautions when using Smart Care

•

If light from a light bulb, ﬂuorescent bulb, or lamp is reﬂected on the display panel of

the washing machine, the smartphone may not be able to recognize the panel or error

message easily.

•

If you hold the smartphone at too large an angle relative to the front of the display panel,

it may not be able to recognize the error code. For best results, hold the smartphone so

that the front of the panel and the smartphone are parallel or nearly parallel.

Operating instructions, tips _33

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd Sec3:33

2012-06-25

5:21:07

Operating instructions, tips

RACK DRY

Installing the drying rack

1. Open the dryer door.

2. Position the drying rack in the tumbler,, placing the front lip of the drying rack on the top of

the lint ﬁlter.

3. Place the rear legs in the two recessed areas of the dryer’s back wall, and then push down

the middle of the drying rack to ﬁx in place.

4. Place the items to be dried on the rack, leaving space between them so air can circulate.

5. Close the dryer door.

6. Press the Rack Dry button in the Time Dry cycle and then select the time according to the

amount of moisture and the weight of the items. The drying rack can be also used at Air Fluﬀ

cycle.

Drying Rack

Door

RECOMMENDED ITEMS

MAXIMUM AMOUNT

Normal

Cottons, Work clothes, Linen, Mixed loads

Heavy fabrics such as jean, Corduroys, Heavy work clothes

Shirts, Synthetic fabrics, Knits, Wrinkle-free cottons, Permanent

Bulky items such as blankets, Sheets, Comforters, Pillows

Underwear, Blouses, Lingerie

Heavy Duty

Perm Press

Bedding PLUS

Delicates

Sensor Dry

Sanitize

Bedding, Curtains, Children` clothing

Eco Normal

Cottons, Work clothes, Linen

For machine washable and tumble dryable wool only

(Maximum amount : 3lb)

Wool

Air Fluﬀ

Form, Rubber, Plastic

Small loads

Manual Dry

Quick Dry

Time Dry

Wrinkle Away

Refresh

Any load

Shirts, Trouser, Blouses

Shirts, Trouser, Comforter, Pillows

Steam

Cycles

FUNCTIONS

OPTIONS

Temp. Control

CYCLE

Sensor Dry

Level

Wrinkle Delay

Prevent Start

Time

Medium

Low

Extra

Low

High

Medium

Low

Normal

Normal dry









Heavy Duty

Perm Press

Bedding PLUS

Delicates





Sensor Dry

Very dry

(No change)

Sanitize

Eco Normal

Wool



Normal dry

(No change)*



(DV455G)*

Normal dry

(No change)



Air Fluﬀ



Manual Dry

Quick Dry

Time Dry

Wrinkle Away

Refresh





Steam Cycles

* is only Gas model

Load Size Recommendations

Large load

Fill the drum to about ¾ full. Do not add items over this level as they need to

tumble freely.

Medium load

Small load

Fill the drum to about ½ full.

Fill the drum with 3~5 items, not more than ¼ full.

For best results, follow the load size recommendations for each drying cycle.

Appendix _73

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd Sec7:73

2012-06-25

5:21:26

Appendix

OPEN SOURCE ANNOUNCEMENT

The software included in this product contains copyrighted software that is licensed under the GPL/LGPL.

You may obtain the complete Corresponding Source code from us for a period of three years after our last

shipment of this product by sending email to:

[email protected]

If you want to obtain the complete Corresponding Source code in the physical medium such as CD-ROM,

the cost of physically performing source distribution may be charged.

This oﬀer is valid to anyone in receipt of this information.

GPL Software:

Bridge-Utils, BusyBox, DNRD, dosfstools, iproute2, IPTables, Linux Kernel, ntpclient, Open1x, RSDK

toolchain, rtl819x - Bootloader, samba, squashfs, udhcp Server-Client Package, USB-ModeSwitch,

wireless-tools

LGPL Software:

libnl-Netlink Library, Mini-XML

GNU GENERAL PUBLIC LICENSE

Version 2, June 1991

51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA

Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not

allowed.

Preamble

The licenses for most software are designed to take away your freedom to share and change

it. By contrast, the GNU General Public License is intended to guarantee your freedom to share

and change free software--to make sure the software is free for all its users. This General Public

License applies to most of the Free Software Foundation’s software and to any other program

whose authors commit to using it. (Some other Free Software Foundation software is covered by

the GNU Lesser General Public License instead.)

You can apply it to your programs, too.

When we speak of free software, we are referring to freedom, not price. Our General Public

Licenses are designed to make sure that you have the freedom to distribute copies of free

software (and charge for this service if you wish), that you receive source code or can get it if you

want it, that you can change the software or use pieces of it in new free programs; and that you

know you can do these things.

To protect your rights, we need to make restrictions that forbid anyone to deny you these rights

or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you

if you distribute copies of the software, or if you modify it.

For example, if you distribute copies of such a program, whether gratis or for a fee, you must

give the recipients all the rights that you have. You must make sure that they, too, receive or can

get the source code. And you must show them these terms so they know their rights.

We protect your rights with two steps: (1) copyright the software, and (2) oﬀer you this license

which gives you legal permission to copy, distribute and/or modify the software.

Also, for each author’s protection and ours, we want to make certain that everyone understands

that there is no warranty for this free software. If the software is modiﬁed by someone else and

passed on, we want its recipients to know that what they have is not the original, so that any

74_ Appendix

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd Sec7:74

2012-06-25

5:21:26

problems introduced by others will not reﬂect on the original authors’ reputations.

Finally, any free program is threatened constantly by software patents. We wish to avoid the

danger that redistributors of a free program will individually obtain patent licenses, in eﬀect

making the program proprietary. To prevent this, we have made it clear that any patent must be

licensed for everyone’s free use or not licensed at all.

The precise terms and conditions for copying, distribution and modiﬁcation follow.

TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND

MODIFICATION

1. This License applies to any program or other work which contains a notice placed by the

The “Program”, below, refers to any such program or work, and a “work based on the

Program” means either the Program or any derivative work under copyright law: that is to

say, a work containing the Program or a portion of it, either verbatim or with modiﬁcations

and/or translated into another language. (Hereinafter, translation is included without limitation

in the term “modiﬁcation”.) Each licensee is addressed as “you”.

Activities other than copying, distribution and modiﬁcation are not covered by this License;

they are outside its scope. The act of running the Program is not restricted, and the output

from the Program is covered only if its contents constitute a work based on the Program

(independent of having been made by running the Program). Whether that is true depends on

what the Program does.

2. You may copy and distribute verbatim copies of the Program’s source code as you receive

it, in any medium, provided that you conspicuously and appropriately publish on each copy

an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that

refer to this License and to the absence of any warranty; and give any other recipients of the

Program a copy of this License along with the Program.

You may charge a fee for the physical act of transferring a copy, and you may at your option

oﬀer warranty protection in exchange for a fee.

3. You may modify your copy or copies of the Program or any portion of it, thus forming a work

based on the Program, and copy and distribute such modiﬁcations or work under the terms

of Section 1 above, provided that you also meet all of these conditions:

1) You must cause the modiﬁed ﬁles to carry prominent notices stating that you changed

the ﬁles and the date of any change.

2) You must cause any work that you distribute or publish, that in whole or in part contains

or is derived from the Program or any part thereof, to be licensed as a whole at no charge

to all third parties under the terms of this License.

3) If the modiﬁed program normally reads commands interactively when run, you must

cause it, when started running for such interactive use in the most ordinary way, to print

or display an announcement including an appropriate copyright notice and a notice that

there is no warranty (or else, saying that you provide a warranty) and that users may

redistribute the program under these conditions, and telling the user how to view a copy

of this License. (Exception: if the Program itself is interactive but does not normally print

such an announcement, your work based on the Program is not required to print an

announcement.)

These requirements apply to the modiﬁed work as a whole. If identiﬁable sections of that

work are not derived from the Program, and can be reasonably considered independent

and separate works in themselves, then this License, and its terms, do not apply to those

sections when you distribute them as separate works. But when you distribute the same

sections as part of a whole which is a work based on the Program, the distribution of the

whole must be on the terms of this License, whose permissions for other licensees extend to

the entire whole, and thus to each and every part regardless of who wrote it.

Thus, it is not the intent of this section to claim rights or contest your rights to work written

Appendix _75

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd Sec7:75

2012-06-25

5:21:26

Appendix

entirely by you; rather, the intent is to exercise the right to control the distribution of derivative

or collective works based on the Program.

In addition, mere aggregation of another work not based on the Program with the Program

(or with a work based on the Program) on a volume of a storage or distribution medium does

not bring the other work under the scope of this License.

4. 3. You may copy and distribute the Program (or a work based on it, under Section 2) in

object code or executable form under the terms of Sections 1 and 2 above provided that you

also do one of the following:

1) Accompany it with the complete corresponding machinereadable source code, which

must be distributed under the terms of Sections 1 and 2 above on a medium customarily

used for software interchange; or,

2) Accompany it with a written oﬀer, valid for at least three years, to give any third party,

for a charge no more than your cost of physically performing source distribution, a

complete machine-readable copy of the corresponding source code, to be distributed

under the terms of Sections 1 and 2 above on a medium customarily used for software

interchange; or, c) Accompany it with the information you received as to the oﬀer to

distribute corresponding source code. (This alternative is allowed only for noncommercial

distribution and only if you received the program in object code or executable form with

such an oﬀer, in accord with Subsection b above.)

The source code for a work means the preferred form of the work for making modiﬁcations

to it. For an executable work, complete source code means all the source code for all

modules it contains, plus any associated interface deﬁnition ﬁles, plus the scripts used to

control compilation and installation of the executable. However, as a special exception,

the source code distributed need not include anything that is normally distributed (in either

source or binary form) with the major components (compiler, kernel, and so on) of the

operating system on which the executable runs, unless that component itself accompanies

the executable.

If distribution of executable or object code is made by oﬀering access to copy from a

designated place, then oﬀering equivalent access to copy the source code from the same

place counts as distribution of the source code, even though third parties are not compelled

to copy the source

along with the object code.

5. You may not copy, modify, sublicense, or distribute the Program except as expressly

provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute

the Program is void, and will automatically terminate your rights under this License. However,

parties who have received copies, or rights, from you under this License will not have their

licenses terminated so long as such parties remain in full compliance.

6. You are not required to accept this License, since you have not signed it. However, nothing

else grants you permission to modify or distribute the Program or its derivative works. These

actions are prohibited by law if you do not accept this License. Therefore, by modifying or

distributing the Program (or any work based on the Program), you indicate your acceptance

of this License to do so, and all its terms and conditions for copying, distributing or modifying

the Program or works based on it.

7. Each time you redistribute the Program (or any work based on the Program), the recipient

automatically receives a license from the original licensor to copy, distribute or modify the

Program subject to these terms and conditions. You may not impose any further restrictions

on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing

compliance by third parties to this License.

76_ Appendix

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd Sec7:76

2012-06-25

5:21:26

8. If, as a consequence of a court judgment or allegation of patent infringement or for any

other reason (not limited to patent issues), conditions are imposed on you (whether by

court order, agreement or otherwise) that contradict the conditions of this License, they do

not excuse you from the conditions of this License. If you cannot distribute so as to satisfy

simultaneously your obligations under this License and any other pertinent obligations, then

as a consequence you may not distribute the Program at all. For example, if a patent license

would not permit royalty-free redistribution of the Program by all those who receive copies

directly or indirectly through you, then the only way you could satisfy both it and this License

would be to refrain entirely from distribution of the Program.

If any portion of this section is held invalid or unenforceable under any particular

circumstance, the balance of the section is intended to apply and the section as a whole is

intended to apply in other circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property

right claims or to contest validity of any such claims; this section has the sole purpose of

protecting the integrity of the free software distribution system, which is implemented by

public license practices. Many people have made generous contributions to the wide range

of software distributed through that system in reliance on consistent application of that

system; it is up to the author/donor to decide if he or she is willing to distribute software

through any other system and a licensee cannot impose that choice.

This section is intended to make thoroughly clear what is believed to be a consequence of

the rest of this License.

9. If the distribution and/or use of the Program is restricted in certain countries either by patents

or by copyrighted interfaces, the original copyright holder who places the Program under this

License may add an explicit geographical distribution limitation excluding those countries, so

that distribution is permitted only in or among countries not thus excluded. In such case, this

License incorporates the limitation as if written in the body of this License.

10. The Free Software Foundation may publish revised and/or new versions of the General Public

License from time to time. Such new versions will be similar in spirit to the present version,

but may diﬀer in detail to address new problems or concerns.

Each version is given a distinguishing version number. If the Program speciﬁes a version

number of this License which applies to it and “any later version”, you have the option of

following the terms and conditions either of that version or of any later version published

by the Free Software Foundation. If the Program does not specify a version number of this

License, you may choose any version ever published by the Free Software Foundation.

11. If you wish to incorporate parts of the Program into other free programs whose distribution

conditions are diﬀerent, write to the author to ask for permission. For software which is

copyrighted by the Free Software Foundation, write to the Free Software Foundation;

we sometimes make exceptions for this. Our decision will be guided by the two goals of

preserving the free status of all derivatives of our free software and of promoting the sharing

and reuse of software generally.

NO WARRANTY

12. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY

FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT

WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER

PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER

EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES

OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK

AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD

THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY

SERVICING, REPAIR OR CORRECTION.

Appendix _77

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd Sec7:77

2012-06-25

5:21:26

Appendix

13. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING

WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR

REDISTRIBUTE THE PROGRAM AS PERMITTED ABOV E , BE L I ABL E TO YOU FOR

DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL

DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING

BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR

LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO

OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY

HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS

How to Apply These Terms to Your New Programs

If you develop a new program, and you want it to be of the greatest possible use to the public,

the best way to achieve this is to make it free software which everyone can redistribute and

change under these terms.

To do so, attach the following notices to the program. It is safest to attach them to the start of

each source ﬁle to most eﬀectively convey the exclusion of warranty; and each ﬁle should have at

least the “copyright” line and a pointer to where the full notice is found.

one line to give the program’s name and an idea of what it does.

This program is free software; you can redistribute it and/or modify it under the terms of the GNU

General Public License as published by the Free Software Foundation; either version 2 of the

License, or (at your option) any later version.

This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY;

without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR

PURPOSE. See the GNU General Public License for more details.

You should have received a copy of the GNU General Public License along with this program;

if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA

02110-1301, USA.

Also add information on how to contact you by electronic and paper mail.

If the program is interactive, make it output a short notice like this when it starts in an interactive

mode:

Gnomovision version 69, Copyright (C) year name of author Gnomovision comes with

ABSOLUTELY NO WARRANTY; for details type `show w’. This is free software, and you are

welcome to redistribute it under certain conditions; type `show c’ for details.

The hypothetical commands `show w’ and `show c’ should show the appropriate parts of the

General Public License. Of course, the commands you use may be called something other than

`show w’ and `show c’; they could even be mouse-clicks or menu items--whatever suits your

program. You should also get your employer (if you work as a programmer) or your school, if any,

to sign a “copyright disclaimer” for the program, if necessary. Here is a sample; alter the names:

Yoyodyne, Inc., hereby disclaims all copyright interest in the program `Gnomovision’ (which

makes passes at compilers) written by James Hacker.

signature of Ty Coon, 1 April 1989

Ty Coon, President of Vice

This General Public License does not permit incorporating your program into proprietary

programs. If your program is a subroutine library, you may consider it more useful to permit

linking proprietary applications with the library. If this is what you want to do, use the GNU Lesser

General Public License instead of this License.

78_ Appendix

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd Sec7:78

2012-06-25

5:21:26

GNU LESSER GENERAL PUBLIC LICENSE

Version 2.1, February 1999

51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA

Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is

not allowed.

[This is the ﬁrst released version of the Lesser GPL. It also counts as the successor of the GNU Library

Public License, version 2, hence the version number 2.1.]

Preamble

The licenses for most software are designed to take away your freedom to share and change it.

By contrast, the GNU General Public Licenses are intended to guarantee your freedom to share

and change free software--to make sure the software is free for all its users.

This license, the Lesser General Public License, applies to some specially designated software

packages--typically libraries--of the Free Software Foundation and other authors who decide to

use it. You can use it too, but we suggest you ﬁrst think carefully about whether this license or

the ordinary General Public License is the better strategy to use in any particular case, based on

the explanations below.

When we speak of free software, we are referring to freedom of use, not price. Our General

Public Licenses are designed to make sure that you have the freedom to distribute copies of free

software (and charge for this service if you wish); that you receive source code or can get it if you

want it; that you can change the software and use pieces of it in new free programs; and that

you are informed that you can do these things.

To protect your rights, we need to make restrictions that forbid distributors to deny you

these rights or to ask you to surrender these rights. These restrictions translate to certain

responsibilities for you if you distribute copies of the library or if you modify it.

For example, if you distribute copies of the library, whether gratis or for a fee, you must give the

recipients all the rights that we gave you. You must make sure that they, too, receive or can get

the source code. If you link other code with the library, you must provide complete object ﬁles

to the recipients, so that they can relink them with the library after making changes to the library

and recompiling it. And you must show them these terms so they know their rights.

We protect your rights with a two-step method: (1) we copyright the library, and (2) we oﬀer you

this license, which gives you legal permission to copy, distribute and/or modify the library.

To protect each distributor, we want to make it very clear that there is no warranty for the free

library. Also, if the library is modiﬁed by someone else and passed on, the recipients should

know that what they have is not the original version, so that the original author’s reputation will

not be aﬀected by problems that might be introduced by others.

Finally, software patents pose a constant threat to the existence of any free program. We wish to

make sure that a company cannot eﬀectively restrict the users of a free program by obtaining a

restrictive license from a patent holder. Therefore, we insist that any patent license obtained for a

version of the library must be consistent with the full freedom of use speciﬁed in this license.

Most GNU software, including some libraries, is covered by the ordinary GNU General Public

License. This license, the GNU Lesser General Public License, applies to certain designated

libraries, and is quite diﬀerent from the ordinary General Public License. We use this license for

certain libraries in order to permit linking those libraries into nonfree programs.

When a program is linked with a library, whether statically or using a shared library, the

combination of the two is legally speaking a combined work, a derivative of the original library.

The ordinary General Public License therefore permits such linking only if the entire combination

ﬁts its criteria of freedom. The Lesser General Public License permits more lax criteria for linking

other code with the library.

We call this license the “Lesser” General Public License because it does Less to protect the

Appendix _79

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd Sec7:79

2012-06-25

5:21:26

Appendix

user’s freedom than the ordinary General Public License. It also provides other free software

developers Less of an advantage over competing non-free programs. These disadvantages are

the reason we use the ordinary General Public License for many libraries.

However, the Lesser license provides advantages in certain special circumstances.

For example, on rare occasions, there may be a special need to encourage the widest possible

use of a certain library, so that it becomes a de-facto standard. To achieve this, non-free

programs must be allowed to use the library.

A more frequent case is that a free library does the same job as widely used non-free libraries.

In this case, there is little to gain by limiting the free library to free software only, so we use the

Lesser General Public License.

In other cases, permission to use a particular library in nonfree programs enables a greater

number of people to use a large body of free software. For example, permission to use the GNU

C Library in non-free programs enables many more people to use the whole GNU operating

system, as well as its variant, the GNU/Linux operating system.

Although the Lesser General Public License is Less protective of the users’ freedom, it does

ensure that the user of a program that is linked with the Library has the freedom and the

wherewithal to run that program using a modiﬁed version of the Library.

The precise terms and conditions for copying, distribution and modiﬁcation follow. Pay close

attention to the diﬀerence between a “work based on the library” and a “work that uses the

library”. The former contains code derived from the library, whereas the latter must be combined

with the library in order to run.

TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND

MODIFICATION

1. This License Agreement applies to any software library or other program which contains a

notice placed by the copyright holder or other authorized party saying it may be distributed

under the terms of this Lesser General Public License (also called “this License”). Each

licensee is addressed as “you”.

A “library” means a collection of software functions and/or data prepared so as to be

conveniently linked with application programs (which use some of those functions and data)

to form executables.

The “Library”, below, refers to any such software library or work which has been distributed

under these terms. A “work based on the Library” means either the Library or any derivative

work under copyright law: that is to say, a work containing the Library or a portion of it, either

verbatim or with modiﬁcations and/or translated straightforwardly into another language.

(Hereinafter, translation is included without limitation in the term “modiﬁcation”.)

“Source code” for a work means the preferred form of the work for making modiﬁcations to

it. For a library, complete source code means all the source code for all modules it contains,

plus any associated interface deﬁnition ﬁles, plus the scripts used to control compilation and

installation of the library.

Activities other than copying, distribution and modiﬁcation are not covered by this License;

they are outside its scope. The act of running a program using the Library is not restricted,

and output from such a program is covered only if its contents constitute a work based on

the Library (independent of the use of the Library in a tool for writing it).

Whether that is true depends on what the Library does and what the program that uses the

Library does.

2. You may copy and distribute verbatim copies of the Library’s complete source code as you

receive it, in any medium, provided that you conspicuously and appropriately publish on each

copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices

that refer to this License and to the absence of any warranty; and distribute a copy of this

License along with the Library.

You may charge a fee for the physical act of transferring a copy, and you may at your option

80_ Appendix

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd Sec7:80

2012-06-25

5:21:26

oﬀer warranty protection in exchange for a fee.

3. You may modify your copy or copies of the Library or any portion of it, thus forming a work

based on the Library, and copy and distribute such modiﬁcations or work under the terms of

Section 1 above, provided that you also meet all of these conditions:

1) The modiﬁed work must itself be a software library.

2) You must cause the ﬁles modiﬁed to carry prominent notices stating that you changed

the ﬁles and the date of any change.

3) You must cause the whole of the work to be licensed at no charge to all third parties

under the terms of this License.

4) If a facility in the modiﬁed Library refers to a function or a table of data to be supplied by

an application program that uses the facility, other than as an argument passed when the

facility is invoked, then you must make a good faith eﬀort to ensure that, in the event an

application does not supply such function or table, the facility still operates, and performs

whatever part of its purpose remains meaningful.

(For example, a function in a library to compute square roots has a purpose that is entirely

well-deﬁned independent of the application. Therefore, Subsection 2d requires that

any application-supplied function or table used by this function must be optional: if the

application does not supply it, the square root function must still compute square roots.)

These requirements apply to the modiﬁed work as a whole. If identiﬁable sections of that

work are not derived from the Library, and can be reasonably considered independent

and separate works in themselves, then this License, and its terms, do not apply to those

sections when you distribute them as separate works. But when you distribute the same

sections as part of a whole which is a work based on the Library, the distribution of the

whole must be on the terms of this License, whose permissions for other licensees extend to

the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not

the intent of this section to claim rights or contest your rights to work written entirely by you;

rather, the intent is to exercise the right to control the distribution of derivative or collective

works based on the Library. In addition, mere aggregation of another work not based on

the Library with the Library (or with a work based on the Library) on a volume of a storage or

distribution medium does not bring the other work under the scope of this License.

4. You may opt to apply the terms of the ordinary GNU General Public License instead of this

License to a given copy of the Library. To do this, you must alter all the notices that refer to

this License, so that they refer to the ordinary GNU General Public License, version 2, instead

of to this License. (If a newer version than version 2 of the ordinary GNU General Public

License has appeared, then you can specify that version instead if you wish.) Do not make

any other change in these notices.

Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU

General Public License applies to all subsequent copies and derivative works made from that

copy.

This option is useful when you wish to copy part of the code of the Library into a program

that is not a library.

5. You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in

object code or executable form under the terms of Sections 1 and 2 above provided that you

accompany it with the complete corresponding machine-readable source code, which must

be distributed under the terms of Sections 1 and 2 above on a medium customarily used for

software interchange.

If distribution of object code is made by oﬀering access to copy from a designated place,

then oﬀering equivalent access to copy the source code from the same place satisﬁes the

requirement to distribute the source code, even though third parties are not compelled to

copy the source along with the object code.

Appendix _81

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd Sec7:81

2012-06-25

5:21:26

Appendix

6. A program that contains no derivative of any portion of the Library, but is designed to work

with the Library by being compiled or linked with it, is called a “work that uses the Library”.

Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the

scope of this License.

However, linking a “work that uses the Library” with the Library creates an executable that

is a derivative of the Library (because it contains portions of the Library), rather than a “work

that uses the library”. The executable is therefore covered by this License. Section 6 states

terms for distribution of such executables.

When a “work that uses the Library” uses material from a header ﬁle that is part of the

Library, the object code for the work may be a derivative work of the Library even though

the source code is not. Whether this is true is especially signiﬁcant if the work can be linked

without the Library, or if the work is itself a library. The threshold for this to be true is not

precisely deﬁned by law.

If such an object ﬁle uses only numerical parameters, data structure layouts and accessors,

and small macros and small inline functions (ten lines or less in length), then the use of the

object ﬁle is unrestricted, regardless of whether it is legally a derivative work. (Executables

containing this object code plus portions of the Library will still fall under Section 6.)

Otherwise, if the work is a derivative of the Library, you may distribute the object code for

the work under the terms of Section 6. Any executables containing that work also fall under

Section 6, whether or not they are linked directly with the Library itself.

7. As an exception to the Sections above, you may also combine or link a “work that uses the

Library” with the Library to produce a work containing portions of the Library, and distribute

that work under terms of your choice, provided that the terms permit modiﬁcation of the work

for the customer’s own use and reverse engineering for debugging such modiﬁcations.

You must give prominent notice with each copy of the work that the Library is used in it

and that the Library and its use are covered by this License. You must supply a copy of

this License. If the work during execution displays copyright notices, you must include the

copy of this License. Also, you must do one of these things:

1) Accompany the work wi th the complet e corresponding machine-readable source

code for the Library including whatever changes were used in the work (which must be

distributed under Sections 1 and 2 above); and, if the work is an executable linked with

the Library, with the complete machine-readable “work that uses the Library”, as object

code and/or source code, so that the user can modify the Library and then relink to

produce a modiﬁed executable containing the modiﬁed Library. (It is understood that the

user who changes the contents of deﬁnitions ﬁles in the Library will not necessarily be

able to recompile the application to use the modiﬁed deﬁnitions.)

2) Use a suitable shared library mechanism for linking with the Library. A suitable

mechanism is one that (1) uses at run time a copy of the library already present on the

user’s computer system, rather than copying library functions into the executable, and (2)

will operate properly with a modiﬁed version of the library, if the user installs one, as long

as the modiﬁed version is interfacecompatible with the version that the work was made

with.

3) Accompany the work with a written oﬀer, valid for at least three years, to give the same

user the materials speciﬁed in Subsection 6a, above, for a charge no more than the cost

of performing this distribution.

4) If distribution of the work is made by oﬀering access to copy from a designated place,

oﬀer equivalent access to copy the above speciﬁed materials from the same place.

5) Verify that the user has already received a copy of these materials or that you have

already sent this user a copy.

For an executable, the required form of the “work that uses the Library” must include any

data and utility programs needed for reproducing the executable from it. However, as a

special exception, the materials to be distributed need not include anything that is normally

82_ Appendix

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd Sec7:82

2012-06-25

5:21:26

distributed (in either source or binary form) with the major components (compiler, kernel, and

so on) of the operating system on which the executable runs, unless that component itself

accompanies the executable.

It may happen that this requirement contradicts the license restrictions of other proprietary

libraries that do not normally accompany the operating system. Such a contradiction means

you cannot use both them and the Library together in an executable that you distribute.

8. You may place library facilities that are a work based on the Library side-by-side in a single

library together with other library facilities not covered by this License, and distribute such

a combined library, provided that the separate distribution of the work based on the Library

and of the other library facilities is otherwise permitted, and provided that you do these two

things:

1) Accompany the combined library with a copy of the same work based on the Library,

uncombined with any other library facilities. This must be distributed under the terms of

the Sections above.

2) Give prominent notice with the combined library of the fact that part of it is a work based

on the Library, and explaining where to ﬁnd the accompanying uncombined form of the

same work.

9. You may not copy, modify, sublicense, link with, or distribute the Library except as expressly

provided under this License. Any attempt otherwise to copy, modify, sublicense, link with, or

distribute the Library is void, and will automatically terminate your rights under this License.

However, parties who have received copies, or rights, from you under this License will not

have their licenses terminated so long as such parties remain in full compliance.

10. You are not required to accept this License, since you have not signed it. However, nothing

else grants you permission to modify or distribute the Library or its derivative works. These

actions are prohibited by law if you do not accept this License. Therefore, by modifying or

distributing the Library (or any work based on the Library), you indicate your acceptance of

this License to do so, and all its terms and conditions for copying, distributing or modifying

the Library or works based on it.

11. Each time you redistribute the Library (or any work based on the Library), the recipient

automatically receives a license from the original licensor to copy, distribute, link with or

modify the Library subject to these terms and conditions. You may not impose any further

restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for

enforcing compliance by third parties with this License.

12. If, as a consequence of a court judgment or allegation of patent infringement or for any

other reason (not limited to patent issues), conditions are imposed on you (whether by

court order, agreement or otherwise) that contradict the conditions of this License, they do

not excuse you from the conditions of this License. If you cannot distribute so as to satisfy

simultaneously your obligations under this License and any other pertinent obligations, then

as a consequence you may not distribute the Library at all. For example, if a patent license

would not permit royalty-free redistribution of the Library by all those who receive copies

directly or indirectly through you, then the only way you could satisfy both it and this License

would be to refrain entirely from distribution of the Library.

If any portion of this section is held invalid or unenforceable under any particular

circumstance, the balance of the section is intended to apply, and the section as a whole is

intended to apply in other circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property

right claims or to contest validity of any such claims; this section has the sole purpose of

protecting the integrity of the free software distribution system which is implemented by

public license practices.

Many people have made generous contributions to the wide range of software distributed

through that system in reliance on consistent application of that system; it is up to the author/

donor to decide if he or she is willing to distribute software through any other system and a

licensee cannot impose that choice.

Appendix _83

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd Sec7:83

2012-06-25

5:21:27

Appendix

This section is intended to make thoroughly clear what is believed to be a consequence of

the rest of this License.

13. If the distribution and/or use of the Library is restricted in certain countries either by patents

or by copyrighted interfaces, the original copyright holder who places the Library under this

License may add an explicit geographical distribution limitation excluding those countries, so

that distribution is permitted only in or among countries not thus excluded. In such case, this

License incorporates the limitation as if written in the body of this License.

14. The Free Software Foundation may publish revised and/or new versions of the Lesser

General Public License from time to time. Such new versions will be similar in spirit to the

present version, but may diﬀer in detail to address new problems or concerns.

Each version is given a distinguishing version number.

If the Library speciﬁes a version number of this License which applies to it and “any later

version”, you have the option of following the terms and conditions either of that version or of

any later version published by the Free Software Foundation. If the Library does not specify

a license version number, you may choose any version ever published by the Free Software

Foundation.

15. If you wish to incorporate parts of the Library into other free programs whose distribution

conditions are incompatible with these, write to the author to ask for permission. For software

which is copyrighted by the Free Software Foundation, write to the Free Software Foundation;

we sometimes make exceptions for this. Our decision will be guided by the two goals of

preserving the free status of all derivatives of our free software and of promoting the sharing

and reuse of software generally.

NO WARRANTY

16. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY

FOR THE LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT

WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER

PARTIES PROVIDE THE LIBRARY “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER

EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES

OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK

AS TO THE QUALITY AND PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE

LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING,

REPAIR OR CORRECTION.

17. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRI T ING

WI L L ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/

OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR

DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL

DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY (INCLUDING

BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR

LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY TO

OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY

HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS

How to Apply These Terms to Your New Libraries If you develop a new library, and you want

it to be of the greatest possible use to the public, we recommend making it free software that

everyone can redistribute and change. You can do so by permitting redistribution under these

terms (or, alternatively, under the terms of the ordinary General Public License).

To apply these terms, attach the following notices to the library. It is safest to attach them to the

start of each source ﬁle to most eﬀectively convey the exclusion of warranty; and each ﬁle should

have at least the “copyright” line and a pointer to where the full notice is found.

one line to give the library’s name and an idea of what it does.

84_ Appendix

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd Sec7:84

2012-06-25

5:21:27

This library is free software; you can redistribute it and/or modify it under the terms of the GNU

Lesser General Public License as published by the Free Software Foundation; either version 2.1

of the License, or (at your option) any later version.

This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY;

without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR

PURPOSE. See the GNU

Lesser General Public License for more details.

You should have received a copy of the GNU Lesser General Public License along with this

library; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,

MA 02110-1301 USA Also add information on how to contact you by electronic and paper mail.

You should also get your employer (if you work as a programmer) or your school, if any, to sign a

“copyright disclaimer” for the library, if necessary. Here is a sample; alter the names: Yoyodyne,

Inc., hereby disclaims all copyright interest in the library `Frob’ (a library for tweaking knobs)

written by James Random Hacker.

signature of Ty Coon, 1 April 1990

Ty Coon, President of Vice

That’s all there is to it!

BSD LICENSE

ﬂex: the fast lexical analyser

The Flex Project.

LibNet License

PPP/ Debian

Redistribution and use in source and binary forms, with or without modiﬁcation, are permitted provided that

the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the

following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the

following disclaimer in the documentation and/or other materials provided with the distribution.

3. Neither the name of the <organization> nor the names of its contributors may be used to endorse or

promote products derived from this software without speciﬁc prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY

EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES

OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT

SHALL <COPYRIGHT HOLDER> BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,

EXEMPLARY, OR CONSEQUENTIAL DAMAGES ( INCLUDING, BUT NOT LIMITED TO, PROCUREMENT

OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS

INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,

STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF

THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

Appendix _85

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd Sec7:85

2012-06-25

5:21:27

Appendix

OPENSSL

This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://

www.openssl.org/)

This product includes cryptographic software written by Eric Young ([email protected])

LICENSE ISSUES

=====================================================================

The OpenSSL toolkit stays under a dual license, i.e. both the conditions of the OpenSSL License

and the original SSLeay license apply to the toolkit. See below for the actual license texts.

Actually both licenses are BSD-style Open Source licenses. In case of any license issues related

to OpenSSL please contact [email protected].

OpenSSL License

=====================================================================

Redistribution and use in source and binary forms, with or without modiﬁcation, are permitted

provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions

and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of

conditions and the following disclaimer in the documentation and/or other materials provided

with the distribution.

3. All advertising materials mentioning features or use of this software must display the following

acknowledgment: “This product includes software developed by the OpenSSL Project for

use in the OpenSSL Toolkit. (http://www.openssl.org/)”

4. The names “OpenSSL Toolkit” and “OpenSSL Project” must not be used to endorse or

promote products derived from this software without prior written permission. For written

permission, please contact [email protected].

5. Products derived from this software may not be called “OpenSSL” nor may “OpenSSL”

appear in their names without prior written permission of the OpenSSL Project.

6. Redistributions of any form whatsoever must retain the following acknowledgment:

“This product includes software developed by the OpenSSL Project for use in the OpenSSL

Toolkit (http://www.openssl.org/)”

THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT “AS IS” AND ANY EXPRESSED

OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES

OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.

IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR

ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL

DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR

SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER

CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,

OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE

USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

=====================================================================

This product includes cryptographic software written by Eric Young ([email protected]). This

product includes software written by Tim Hudson ([email protected]).

86_ Appendix

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd Sec7:86

2012-06-25

5:21:27

Warranty (U.S.A)

SAMSUNG DRYER

LIMITED WARRANTY TO ORIGINAL PURCHASER

This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS AMERICA, INC.

(SAMSUNG) and delivered new, in the original carton to the original consumer purchaser, is warranted by

SAMSUNG against manufacturing defects in materials and workmanship for a limited warranty period of:

One (1) Year All Parts and Labor

Two (2) Years Control Board Parts

This limited warranty begins on the original date of purchase, and is valid only on products purchased and

used in the United States.

To receive warranty service, the purchaser must contact SAMSUNG for problem determination and service

procedures.

Warranty service can only be performed by a SAMSUNG authorized service center.

The original dated bill of sale must be presented upon request as proof of purchase to SAMSUNG or

SAMSUNG’s authorized service center.

SAMSUNG will provide in-home service during the warranty period at no charge, subject to availability

within the contiguous United States.

In-home service is not available in all areas.

To receive in-home service, product must be unobstructed and accessible to the service agent.

If service is not available, SAMSUNG may elect to provide transportation of the product to and from an

authorized service center.

SAMSUNG will repair, replace, or refund this product at our option and at no charge as stipulated herein,

with new or reconditioned parts or products if found to be defective during the limited warranty period

speciﬁed above.

All replaced parts and products become the property of SAMSUNG and must be returned to SAMSUNG.

Replacement parts and products assume the remaining original warranty, or ninety (90) days, whichever is

longer.

This limited warranty covers manufacturing defects in materials and workmanship encountered in normal,

noncommercial use of this product and shall not apply to the following: damage that occurs in shipment;

delivery and installation; applications and uses for which this product was not intended; altered product or

serial numbers; cosmetic damage or exterior ﬁnish; accidents, abuse, neglect, ﬁre, water, lightning, or other

acts of nature or God; use of products, equipment, systems, utilities, services, parts, supplies, accessories,

applications, installations, repairs, external wiring or connectors not supplied or authorized by SAMSUNG

that damage this product or result in service problems; incorrect electrical line voltage, ﬂuctuations and

surges; customer adjustments and failure to follow operating instructions, maintenance and environmental

instructions that are covered and prescribed in the instruction book; product removal and reinstallation;

problems caused by pest infestations.

This limited warranty does not cover problems resulting from incorrect electric current, voltage or supply,

light bulbs, house fuses, house wiring, cost of a service call for instructions, or ﬁxing installation errors.

SAMSUNG does not warrant uninterrupted or error-free operation of the product.

Warranty _87

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd Sec8:87

2012-06-25

5:21:27

Warranty

Except as set forth herein, there are no warranties on this product either express or implied, and samsung

disclaims all warranties including, but not limited to, any implied warranties of merchantability, infringement

or ﬁtness for a particular purpose.

No warranty or guarantee given by any person, ﬁrm, or corporation with respect to this product shall be

binding on samsung.

Samsung shall not be liable for loss of revenue or proﬁts, failure to realize savings or thter beneﬁts, or any

other special, incidental or consequential damages caused by the use, misuse, or inability to use this

product, regardless of the legal theory on which the claim is based, and even if samsung has been advised

of the possibility of such damages.

Nor shall recovery of any kind against samsung be greater in amount than the purchase price of the product

sold by samsung and causing the alleged damage.

Without limiting the foregoing, purchaser assumes all risk and liability for loss, damage, or injury to

purchaser and purchaser’s property and to others and their property arising out of the use, misuse,

or inability to use this product. This limited warranty shall not extend to anyone other than the original

purchaser of this product, is nontransferable and states your exclusive remedy.

Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation

of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This

warranty gives you speciﬁc rights, and you may also have other rights, which vary from state to state.

To obtain warranty service, please contact SAMSUNG at:

Samsung Electronics America, Inc.

85 Challenger Road Ridgeﬁeld Park, NJ 07660

1-800-SAMSUNG (726-7864)

www.samsung.com

Visits by a Service Engineer to explain functions, maintenance or installation is not covered by warranty.

Please contact your Samsung call agent for help with any of these issues.

88_ Warranty

Download from Www.Somanuals.com. All Manuals Search And Download.

DV455-02836F-02_EN_20120625.indd Sec8:88

2012-06-25

5:21:27

Warranty (CANADA)

SAMSUNG DRYER

LIMITED WARRANTY TO ORIGINAL PURCHASER

This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS CANADA, INC.

(SAMSUNG) and delivered new, in the original carton to the original consumer purchaser, is warranted by

SAMSUNG against manufacturing defects in materials and workmanship for a limited warranty period of:

One (1) year part and labor

This limited warranty begins on the original date of purchase, and is valid only on products purchased and

used in the Canada.

To receive warranty service, the purchaser must contact SAMSUNG for problem determination and service

procedures.

Warranty service can only be performed by a SAMSUNG authorized service center.

The original dated bill of sale must be presented upon request as proof of purchase to SAMSUNG or

SAMSUNG’s authorized service center.

SAMSUNG will provide in-home service during the warranty period at no charge, subject to availability

within the Canada.