TXP1430F/ TXP1634F
TXP2022
COLOR TELEVISION
.............
Ow ner’s
Instructions
Printed in Mexico
AA68-02833A (ENG)
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning! Im portant
Safety Instructions
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol indicates high voltage is present inside. It is
dangerous to make any kind of contact with any inside part of
this product.
This symbol alerts you that important literature concerning
operation and maintenance has been included with this product.
Note to CATV system installer: This reminder is provided to call CATV system
installer’s attention to Article 820-40 of the National Electrical Code (Section 54 of
Canadian Electrical Code, Part I), that provides guidelines for proper grounding
and, in particular, specifies that the cable ground shall be connected to the
grounding system of the building as close to the point of cable entry as practical.
Caution: FCC/CSA regulations state that any unauthorized changes or modifica-
tions to this equipment may void the user’s authority to operate it.
Caution: To prevent electric shock, match the wide blade of plug to the wide slot,
and fully insert the plug.
Attention: pour eviter les chocs electriques, introduire la lame le plus large de la
fiche dans la borne correspondante de la prise et pousser jusqu’au fond.
Important: One Federal Court has held that unauthorized recording of
copyrighted TV programs is an infringement of U.S. copyright laws.
Certain Canadian programs may also be copyrighted and any unauthorized
recording in whole or in part may be in violation of these rights.
To prevent damage which may result in fire or electric shock
hazard, do not expose this appliance to rain or moisture.
Download from Www.Somanuals.com. All Manuals Search And Download.
Thank You for Choosing Sam sung
Thank you for choosing Samsung! Your new Samsung TV receiver represents the latest in
television technology. It has easy-to-use, on-screen menus and closed-captioning capabilities,
making this TV one of the best products in its class. This product will provide convenient,
dependable service and enjoyment for years to come.
Im portant Safety Inform ation
To reduce the risk of fire, electrical shock, and other injuries, keep these safety precautions in
mind when installing, using, and maintaining your machine.
• Read all safety and operating instructions before operating the TV receiver.
• Retain the safety and operating instructions for future reference.
• Heed all warnings on the TV receiver and in the operating instructions.
• Follow all operating instructions.
• Unplug the TV receiver from the wall outlet before cleaning, Use a damp cloth, Do not use
liquid or aerosol cleaners.
• Never add any attachments and/or equipment without approval of the manufacturer. Such
additions may cause risk of fire, electric shock, or other personal injury.
• Do not use the TV receiver where contact with or immersion in water is a possibility, such as
near bath tubs, sinks, washing machines, swimming pools, etc.
• Do not place the TV receiver on an unstable cart, stand, tripod,
bracket, or table. The TV receiver may fall, causing injury to
people and/or damage to the TV. Use only with a cart, stand,
tripod, bracket, or table not recommended by the manufacturer or
sold with the TV receiver.
• Follow the manufacturer’s instructions when mounting the unit,
and use a mounting accessory recommended by the manufacturer.
Move the TV receiver and its cart with care. Quick stops, excessive
force, and uneven surfaces may cause the unit and cart to over-
turn.
• Provide ventilation for the TV receiver. The unit is designed with slots in the cabinet for
ventilation to protect it from overheating. Do not block these openings with any object, and
do not place the TV receiver on a bed, sofa, rug, or other similar surface. Do not place it near
a radiator or heat register. If you place the TV receiver on a rack or bookcase, ensure that
there is adequate ventilation and that you’ve followed the manufacturer’s instructions for
mounting.
• Operate your TV receiver only from the type of power source indicated on the marking label.
If you are not sure of the type of power supplied to your home, consult your appliance dealer
or local power company.
• Use only a grounded or polarized outlet. For your safety, this TV is equipped with a polarized
alternating-current line plug having one blade wider than the other. This plug will fit into the
power outlet only one way. If you are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug still does not fit, contact your electrician to replace your outlet.
SAFETY
1
Download from Www.Somanuals.com. All Manuals Search And Download.
• Protect the power cord. Power supply cords should be routed so that they will not be walked
on or pinched by items placed on or against them. Pay particular attention to cord placement
at plugs, convenience receptacles, and at the point where they exit from the unit.
• Unplug the TV receiver from the wall outlet and disconnect the antenna or cable system dur-
ing a lightning storm or when left unattended and unused for long periods of time. This will
prevent damage to the unit due to lightning and power-line surges.
• An outside antenna system should not be placed in the vicinity of overhead power lines or
other electric light or power circuits or where it can fall into such power lines or circuits.
Avoid overhead power lines: When installing an outside antenna system, be extremely careful
to keep from touching the power lines or circuits. Contact with such lines might be fatal.
• Do not overload the wall outlet or extension cords. Overloading can result in fire or electric
shock.
• Do not insert foreign objects through openings in the unit, as they may touch dangerous
voltages or cause damage. Never spill liquid of any kind on the TV receiver.
• Ground outdoor antennas. If an outside antenna or cable
system is connected to the TV receiver, be sure the
antenna or cable system is grounded so as to provide
some protection against voltage surges and built-up static
charges. Read information with respect to proper
grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna
discharge unit, size of grounding conductors, location of
antenna-discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
• Do not attempt to service the TV receiver yourself. Refer all servicing to qualified service
personnel. Unplug the unit from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
- When the power-supply cord or plug is damaged
- If liquid has been spilled on the unit or if objects have fallen into the TV
- If the TV receiver has been exposed to rain or water
- If the TV receiver does not operate normally by following the operating instructions
- If the TV receiver has been dropped or the cabinet has been damaged
- When the TV receiver exhibits a distinct degradation in performance
• If you make adjustments yourself, adjust only those controls that are covered by the operat-
ing instructions. Adjusting other controls may result in damage and will often require exten-
sive work by a qualified technician to restore the TV receiver to normal.
• When replacement parts are required, be sure the service technician uses replacement parts
specified by the manufacturer or those that have the same characteristics as the original part.
Unauthorized substitutions may result in additional damage to the unit.
• Upon completion of any service or repairs to this TV receiver, ask the service technician to
perform safety checks to determine that the TV receiver is in a safe operating condition.
2
SAFETY
Download from Www.Somanuals.com. All Manuals Search And Download.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
DOUBLE INSULATED - When servicing
use only identical replacement parts.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings, Install in accordance with the manufacturer’s
instructions.
8) Do not install near any heat sources such as radiators, heat registers, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two blades
and a third grounding prong. The wide blade or the third prong are provided for your
safety. If the provided plug does not fit into your outlet, consult an electrician for replace-
ment of the obsolete outlet.
10) Protect the power cord from being from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sold
with the apparatus. When a used, caution when moving the cart/apparatus combination to
avoid injury from tip-over.
13) Unplug this apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
SAFETY 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Your New TV . . . . . . . . . . . . . . .1.1
List of Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1
Familiarizing Yourself with The TV. . . . . . . . . . . . . . . . . . . . . . . . . . 1.2
Front Panel Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2
Side Panel Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2
Rear Panel Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4
Chapter 2: Installation . . . . . . . . . . . . . . . . 2.1
Connecting VHF and UHF Antennas . . . . . . . . . . . . . . . . . . . . . . . . 2.1
Antennas with 300-ohm Flat Twin Leads . . . . . . . . . . . . . . 2.1
Antennas with 75-ohm Round Leads . . . . . . . . . . . . . . . . . 2.2
Separate VHF and UHF Antennas. . . . . . . . . . . . . . . . . . . . 2.2
Connecting Cable TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2
Cable without a Cable Box . . . . . . . . . . . . . . . . . . . . . . . . . 2.2
Connecting to a Cable Box that Descrambles
All Channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3
Connecting to a Cable Box that Descrambles
some Channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3
Connecting a VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5
Connecting a Camcorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6
Connecting a DVD player (Option) . . . . . . . . . . . . . . . . . . . . . . . . . 2.6
Installing Batteries in the Remote Control. . . . . . . . . . . . . . . . . . . . . 2.7
Chapter 3: Operation . . . . . . . . . . . . . . . . . . 3.1
Turning the TV On and Off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.1
Viewing the Menus and On-Screen Displays. . . . . . . . . . . . . . . . . . . 3.1
Viewing the Menus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.1
Viewing the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.1
Selecting a Menu Language. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2
Memorizing the Channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3
Selecting the Video Signal-source. . . . . . . . . . . . . . . . . . . . 3.3
Storing Channels in Memory (Automatic Method) . . . . . . . 3.4
Adding and Erasing Channels (Manual Method) . . . . . . . . 3.5
Changing Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.6
Using the Channel Buttons. . . . . . . . . . . . . . . . . . . . . . . . . 3.6
Directly Accessing Channels. . . . . . . . . . . . . . . . . . . . . . . . 3.6
Using the PRE-CH Button to select the Previous Channel. . 3.6
Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.6
Using Mute. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.6
Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.7
Customizing the Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8
Using Automatic Picture Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.9
Using Automatic Sound Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.10
Viewing a VCR or Camcorder Tape. . . . . . . . . . . . . . . . . . . . . . . . . . 3.11
1
CONTENTS
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Special Features . . . . . . . . . . . . 4.1
Customizing Your Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1
Setting Up Your Remote Control to Operate Your
VCR or DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2
Setting Up Your Remote Control to Operate Your Cable Box . . . 4.3
Fine Tuning Channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4
Changing the Screen Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5
Using the Surf Feature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.6
Setting the On/Off Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.7
Setting the Sleep Timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.8
Sound Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.9
Choosing a Multi-Channel Sound (MTS) Soundtrack. . . . . 4.9
Extra sound settings
(Turbo Sound, or Surround) . . . . . . . . . . . . . . . . . . . . . . . 4.10
Viewing Closed Captions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.11
Using the V-Chip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.12
Setting Up Your Personal ID Number (PIN) . . . . . . . . . . . . 4.12
How to Enable/Disable the V-Chip . . . . . . . . . . . . . . . . . . . 4.13
How to Set up Restrictions Using the “TV guidelines” . . . . 4.13
How to Set up Restrictions using the MPAA Ratings:
G, PG, PG-13, R, NC-17, X . . . . . . . . . . . . . . . . . . . . . . . . 4.15
How to Reset the TV after the V-Chip Blocks a Channel
(“Emergency Escape”). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.16
Chapter 5: Troubleshooting . . . . . . . . . . . . 5.1
Identifying Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . A.1
Cleaning and Maintaining Your TV. . . . . . . . . . . . . . . . . . . . . . . . . . A.1
Using Your TV in Another Country . . . . . . . . . . . . . . . . . . . . . . . . . A.1
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.1
CONTENTS
2
Download from Www.Somanuals.com. All Manuals Search And Download.
List of Features
Your Samsung TV was designed with the latest technology. This TV is a high-performance
unit that includes the following special features:
• Easy-to-use remote control
• Easy-to-use on-screen menu system
• Automatic timer to turn the TV on and off
• Adjustable picture settings that can be stored in the TV’s memory
• Automatic channel tuning for up to 181 channels
• Fine tuning control for the sharpest picture possible
• Built-in, dual channel speakers
• A special sleep timer
1.1
CHAPTER ONE: YOUR NEW TV
Download from Www.Somanuals.com. All Manuals Search And Download.
Fam iliarizing Yourself w ith The TV
Front Panel Buttons
The buttons on the front panel control your TV’s basic features, including the on-screen
menu. To use the more advanced features, you must use the remote control.
• TXN1430F
• TXN1634F
• TXN2022
ΠTURBO
Press to feel the middle and low sound
ˇ CH ▼ and CH ▲
Press to change channels or to select fea-
tures on the menu.
effects when watching a music program.
´ – VOL and VOL +
¨ Remote Control Sensor
Aim the remote control towards this spot on
the TV.
Press to change the volume or to change
features on the menu.
MENU
ˆ STAND BY
Press the VOL+/- buttons simultaneously to
see the menu of TV function. (Same function
as the MENU button on the remote control.)
Lights up when you turn the power off.
Ø POWER
Press to turn the TV on or off.
Side Panel J acks
You can use the side panel jacks to connect an A/V component that is used only occa-
sionally, such as a camcorder or video game. (For information on connecting equipment,
see pages 2.1 – 2.6.)
ΠEARPHONE jack (Option)
• TXN1634F
• TXN2022
• TXN1430F
Connect a set of external
earphones to this jack for
private listening.
´ VIDEO and AUDIO input
jacks
Use these jacks to connect
a camcorder or video
game.
CHAPTER ONE: YOUR NEW TV 1.2
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Panel J acks
Use the rear panel jacks to connect an A/V component that will be connected
continuously, such as a VCR.
For more information on connecting equipment, see pages 2.1 – 2.6.
ΠDVD VIDEO input jacks (Option)
Use these jacks to connect the component
video signal from a DVD player.
ˇ VHF/UHF Antenna terminal
Use this terminal to connect an outdoor
antenna or cable system.
´ VIDEO and AUDIO input jacks
Use these jacks to connect a VCR or other
video equipment.
Note: This figure shows the Standard rear panel jack. The actual configuration for your TV
may be different.
1.3
CHAPTER ONE: YOUR NEW TV
Download from Www.Somanuals.com. All Manuals Search And Download.
Rem ote Control
You can use the remote control up to about 23 feet from the TV. When using the remote,
always point it directly at the TV.
ΠPOWER
˝ MENU
Press to turn the TV on and off.
Press this button to see the
easy-to-use menu system.
´ TV/VIDEO
Press to watch TV picture and
Ô VOL – and VOL + (Volume)
Press VOL – to lower the vol-
ume; press VOL + to raise the
volume. Also use with the
menu system.
a picture from a connected
component (VCR, LDP etc.).
ˇ Number buttons
Press to directly select chan-
nels on the TV.
SLEEP
Press for the TV to automati-
cally turn off after an amount
of time that you set.
¨ +100
Press to directly select chan-
nels over 100. For example, to
select channel 121, press
+100, then press 2 and 1.
Ò CH.SCAN (Channel Scan)
Press to have the TV automati-
cally scan all of the channels it
has memorized.
ˆ CH ▲ and CH ▼ (Channel)
Press CH ▲ or CH ▼ to
change channels. Also use
with the on-screen menu sys-
tem.
Ú PRE-CH (Previous Channel)
Press to see the last channel
you were watching.
Ø DISPLAY
Æ TURBO
Press to see the time, channel,
etc., on-screen. Also press to
exit (quit) the menu system.
Press to feel the middle and
low sound effects when
watching a music program.
∏ SURF
ı MTS
Press when viewing a channel
to automatically return to that
channel after an amount of
time that you set.
Press to select stereo, mono,
or secondary audio program
(SAP).
” P-STD
Press to adjust the TV picture
by selecting one of the special
factory settings or your own
custom setting.
’ MUTE
Press to mute (silence) the
volume.
TXN1430F / TXN1634F
CHAPTER ONE: YOUR NEW TV 1.4
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control
You can use the remote control up to about 23 feet from the TV. When using the remote,
always point it directly at the TV.
You can also use your remote control to operate your VCR, DVD and cable box. See page
4.1 for details.
Œ
´
POWER
Turns the TV on and off.
˝ TV
Press to use your remote control
to operate your TV.
Num ber buttons
Press to select channels directly
on the TV.
VCR
Press to use your remote control
to operate your VCR.
+100
Press to select channels over 100.
For example, to select channel
121, press “+100”, then press “2”
and “1”.
CABLE
Press to use your remote control
to operate a cable box.
DVD
ˇ
¨
P.SIZE
Press to use your remote control
to operate your DVD.
Press to change the screen size.
Your choices are Normal screen
or Zoom screen.
Ô
PRE-CH
Tunes to the previous channel.
R.SURF
Press the R.SURF button to auto-
matically return to a preferred
channel after a user-preset time
delay.
MTS (Multichannel
Television Stereo)
Press to choose stereo, mono or
Separate Audio Program (SAP
broadcast).
ˆ
SET
Use this button when you are set-
ting up your remote control to
operate your VCR, DVD or cable
box.
Ò
Ú
DISPLAY
Press to see the time, channel,
etc., on-screen. Also press to exit
(quit) the menu system.
Ø
∏
”
TURBO
Press to turn the TURBO sound On
or Off.
VOL -, VOL
+
Press to increase or decrease the
volume. (Also used to make selec-
tions on the on-screen menus.)
MUTE
Press to temporarily cut off
the sound.
Æ
ı
MENU
Displays the main on-screen
menu.
CH▲ and CH▼
(Channel Up/ Dow n)
Press CH▲ or CH▼ to change
channels. (Also used to highlight
selections on the on-screen
menus.)
TV/ VIDEO
Press to display all of the
available video sources
(i.e., Antenna/cable, VCR).
˜
SLEEP
Press to select a preset time inter-
val for automatic shutoff.
’
P.STD
Adjust the TV picture by selecting
one of the preset factory settings
(or select your personal, cus-
tomized picture settings).
TXN2022
1.5
CHAPTER ONE: YOUR NEW TV
Download from Www.Somanuals.com. All Manuals Search And Download.
Rem ote Control
¯
VCR Controls
˘
PIP Controls
(Not available)
·
REW (Rew ind)
Press to rewind a tape in your
VCR.
SWAP
Exchanges the video signal that is
currently displayed on the main
screen with the signal in the PIP
window.
·
STOP
Press this button to stop a tape
during play, record, rewind or
fast forward. If the button is
pressed during Full-Automatic
play, the function will be can-
celled.
TV/ VIDEO
Press to select one of the available
signal sources for the PIP window.
·
·
PLAY
Press the PLAY button to play
back prerecorded tapes.
PIP/ SIZE
Press this button to control the PIP
window. Press repeatedly to cycle
through this sequence: PIP ON
with large window, PIP ON with
small window, and PIP OFF.
F.F
Press to fast forward the tape in
your VCR.
CH
Not available.
TXN2022
CHAPTER ONE: YOUR NEW TV 1.6
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Connecting VHF and UHF Antennas
If your antenna has a set of leads that
look like this, see “Antennas with
300-ohm Flat Twin Leads,” below.
If your antenna has one lead that looks
like this, see “Antennas with 75-ohm
Round Leads,” on page 2.2.
If you have two antennas, see “Separate
VHF and UHF Antennas,” on page 2.2.
Antennas w ith 300-ohm Flat Tw in Leads
If you are using an off-air antenna (such as a roof antenna or “rabbit ears”) that has
300-ohm twin flat leads, follow the directions below.
1
Place the wires from the
twin leads under the
screws on the 300-75 ohm
adaptor (not supplied).
Use a screwdriver to
tighten the screws.
2
Plug the adaptor into the
VHF/UHF terminal on the
bottom of the back panel.
2.1
CHAPTER TWO: INSTALLATION
Download from Www.Somanuals.com. All Manuals Search And Download.
Antennas w ith 75-ohm Round Leads
1
Plug the antenna lead into
the VHF/UHF
terminal on the bottom of
the back panel.
Separate VHF and UHF Antennas
If you have two separate antennas for your TV (one VHF and one UHF), you must
combine the two antenna signals before connecting the antennas to the TV. This
procedure requires a an optional combiner-adaptor (available at most electronics shops).
1
Connect both antenna
leads to the combiner.
2
Plug the combiner into the
VHF/UHF terminal on the
bottom of the rear panel.
Connecting Cable TV
To connect to a cable TV system, follow the instructions below.
Cable w ithout a Cable Box
Because this TV is cable-ready,
1
you do not need a cable box to view
unscrambled cable channels.
Plug the incoming cable
into the VHF/UHF antenna
terminal on back of the TV.
CHAPTER TWO: INSTALLATION
2.2
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a Cable Box that Descram bles All Channels
This terminal might be labeled
“ANT OUT,” “VHF OUT,” or simply,
“OUT.”
1
Find the cable that is con-
nected to the ANTENNA
OUT terminal on your
cable box.
2
Connect the other end of
this cable to the VHF/UHF
antenna terminal on the
back of the TV.
Connecting to a Cable Box that Descram bles Som e Channels
If your cable box descrambles only some channels (such as premium channels), follow the
instructions below. You will need a two-way splitter, an RF (A/B) switch, and four lengths of
coaxial cable. (These items are available at most electronics stores.)
This terminal might be labeled
“ANT IN,” “VHF IN,” or simply,
“IN.”
1
Find and disconnect the
cable that is connected to
the ANTENNA IN
terminal on your cable
box.
2
Connect this cable to a
two-way splitter.
3
Connect a coaxial cable
between an OUTPUT ter-
minal on the splitter and
the IN terminal on the
cable box.
2.3
CHAPTER TWO: INSTALLATION
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Connect a coaxial cable
between the ANTENNA
OUT terminal on the cable
box and the B–IN terminal
on the A/B switch.
5
Connect another cable
between the other OUT
terminal on the splitter
and the A–IN terminal on
the RF (A/B) switch.
6
Connect the last coaxial
cable between the OUT
terminal on the RF (A/B)
switch and the VHF/UHF
terminal on the rear of the
TV.
After you’ve made this connection, set the A/B switch to the “A” position for normal view-
ing. Set the A/B switch to the “B” position to view scrambled channels. (When you set the
A/B switch to “B,” you will need to tune your TV to the cable box’s output channel, which is
usually channel 3 or 4.)
CHAPTER TWO: INSTALLATION
2.4
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a VCR
These instructions assume that you have already connected your TV to an antenna or a cable
TV system (according to the instructions on pages 2.1-2.4). Skip step 1 if you have not yet
connected to an antenna or a cable system.
1
Unplug the cable or
antenna from the back of
the TV.
2
Connect the cable or
antenna to the
ANTENNA IN terminal on
the back of the VCR.
3
Connect a coaxial cable
between the ANTENNA
OUT terminal on the VCR
and the antenna
terminal on the TV.
A coaxial cable is usually included with a VCR. (If not, check your local electronics
store).
4
Connect a set of audio
cables between the
AUDIO OUT jacks on the
VCR and the AUDIO jacks
on the TV.
5
Connect a video cable
between the VIDEO OUT
jack on the VCR and the
VIDEO jack on the TV.
Follow the instructions in “Viewing a VCR or Camcorder Tape” to view your VCR tape.
Note: This figure shows the Standard connector-jack panel. The actual configuration for
your TV may be different.
2.5
CHAPTER TWO: INSTALLATION
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a Cam corder
The front panel jacks on your TV make it easy to connect a camcorder to your TV.
They allow you to view the camcorder tapes without using a VCR. (Also see “Viewing a VCR
or Camcorder Tape” on page 3.11)
1
Locate the A/V output
jacks on the camcorder.
They are usually found on
the side or back of the
camcorder.
2
Connect an audio cable
between the AUDIO OUT-
PUT jack on the camcorder
and the AUDIO terminals
on the front of the TV.
3
Connect a video cable
between the VIDEO OUT-
PUT jack on the camcorder
and the VIDEO terminal on
the front of the TV.
The audio-video cables shown here are usually included with a Camcorder. (If not, check
your local electronics store.)
Note: This figure shows the Standard connector-jack panel. The actual configuration for
your TV may be different.
Connecting a DVD Player (Option)
The rear panel jacks on your TV make it easy to connect a DVD player to your TV.
1
Connect a set of audio
cables between the AUDIO
INPUT jacks on the TV and
the AUDIO OUT jacks on the
DVD player.
2
Connect a video cable
between the DVD-IN (Y, Pb,
Pr) jacks on the TV and the
DVD-OUT (Y, Pb, Pr) jacks
on the DVD player.
Note: For an explanation of Component video, see your DVD player's owner's manual.
CHAPTER TWO: INSTALLATION
2.6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Batteries in the Rem ote Control
1
Slide the cover out com-
pletely.
Make sure to match the “+” and
2
“–” ends of the batteries with the
diagram inside the compartment.
Install two AA size
batteries.
Remove the batteries and store
them in a cool, dry place if you won’t
be using the remote control for a
long time.
3
Replace the cover.
The remote control can be used up
to about 23 feet from the TV.
(Assuming typical TV usage, the
Batteries last for about one year.)
2.7
CHAPTER TWO: INSTALLATION
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning the TV On and Off
Press the POWER button on the remote control.
You can also use the POWER button on the front panel.
View ing the Menus and On-Screen Displays
View ing the Menus
The on-screen menus disappear
from the screen after about thirty
seconds.
1
With the power on, press
the MENU button.
The main menu appears
on the screen. Its left side
has four icons: Picture,
Sound, Channel, and
Function.
You can also use the MENU,
CHANNEL, and VOLUME buttons
on the control panel of the TV to
make selections.
2
Use the CH▲ and CH▼ buttons to highlight one of the 4 icons.
Then press the VOL+ button to access the icon’s sub-menu.
Press the MENU button to exit.
View ing the Display
The on-screen displays
1
disappear after about twelve seconds.
Press the DISPLAY button.
on the remote control.
When Closed Caption has been set,
the icon(
ing the Display button.
) will appear by press-
The on-screen display
shows any or all of the
following: Active channel,
Audio source and the
time.
CHAPTER THREE: TV OPERATION
3.1
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting a Menu Language
1
Press MENU to display
the menu.
Press CH ▼ three times to
select “Function”,
then press the VOL + but-
ton.
2
Press VOL + to select the
appropriate language:
English, Spanish, or
French.
3
Press MENU twice to exit.
3.2
CHAPTER THREE: TV OPERATION
Download from Www.Somanuals.com. All Manuals Search And Download.
Mem orizing the Channels
Your TV can memorize and store all of the available channels for both “off-air” (antenna)
and cable channels. After the available channels are memorized, use the CH ▲ and
CH ▼ buttons to scan through the channels. This eliminates the need to change chan-
nels by entering the channel digits. There are three steps for memorizing channels:
selecting a broadcast source, memorizing the channels (automatic) and adding and
deleting channels (manual).
Selecting the Video Signal-source
Before your television can begin memorizing the available channels, you must specify
the type of signal source that is connected to the TV (i.e., an antenna or a cable system).
1
Press MENU to
display the menu.
Press CH ▼ two times to
select “Channel”, then
press the VOL + button.
2
Repeatedly press VOL +
to cycle through these
choices:
ANT (antenna)
STD, HRC or IRC (all cable
TV).
Note: STD, HRC and IRC identify various types of cable TV systems. Contact your local cable
company to identify the type of cable system that exists in your particular area.
At this point the signal source has been selected. Proceed to “Storing Channels in Memory”
(next page).
3
Press MENU twice to exit.
CHAPTER THREE: TV OPERATION
3.3
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing Channels in Mem ory (Autom atic Method)
1
First, select the correct
signal source (ANT, STD,
HRC, IRC). See steps 1~3
on previous page.
Press the MENU button,
then press the CH ▼ but-
ton twice to select
“Channel,” then press the
VOL + button.
2
Press the CH ▼ button to
select “Auto program”.
The TV automatically cycles
through all of the available channels
and stores them in memory. This
takes about one to two minutes.
3
Press the VOL + button.
The TV will begin
memorizing all of the
available channels.
Press the MENU button at any time
to interrupt the memorization
process and return to the Channel
menu.
4
After all the available
channels are stored, the
Auto program menu reap-
pears. Press the MENU
button twice to exit.
3.4
CHAPTER THREE: TV OPERATION
Download from Www.Somanuals.com. All Manuals Search And Download.
Adding and Erasing Channels (Manual Method)
1
Press the MENU button.
Press the CH ▼ button
twice to select "Channel",
then press the VOL+ but-
ton.
2
Press the CH ▲ or CH ▼
button to select
“Add/Erase”.
Press the VOL+ button.
3
Press the VOL-/+ or num-
ber buttons to select the
channel you want to add
or erase.
4
Press the CH ▲ or CH ▼
button to select “Select”.
Press the VOL+ or VOL-
button to select “Added”
or “Erased”.
Press the MENU button
three times to exit.
CHAPTER THREE: TV OPERATION
3.5
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Channels
Using the Channel Buttons
1
Press the CH ▲ or CH ▼ button to change channels.
When you press CH ▲ or CH ▼, the TV changes channels in sequence. You will see all the
channels that the TV has memorized. (The TV must have memorized at least three channels.)
You will not see channels that were either erased or not memorized.
Directly Accessing Channels
Use the number buttons to quickly tune to any channel.
1
Press the number buttons to go directly to a channel.
For example, to select channel 27, press “2,” then “7.”
The TV will change channels when you press the
second number.
When you use the number buttons, you can directly select channels that were either erased or
not memorized.
To select a channel over 100, press the +100 button. (For channel 122, press “+100,” then “2,”
then “2.”)
To change to single-digit channels (0–9) faster, press “0” before the
single digit. (For channel “4,” press “0,” then “4.”)
Using the PRE-CH Button to select the Previous Channel
To quickly switch between two
channels that are far apart, tune to
one channel, then use the number
button to select the second channel.
1
Press the PRE-CH button.
The TV will switch to the last channel viewed.
Then, use the PRE-CH button to
quickly alternate between them.
Adjusting the Volum e
Press the VOL + or VOL– button to increase or decrease the volume.
Using Mute
At any time, you can temporarily cut off the sound using the Mute button.
1
Press the MUTE button and the sound cuts off.
The word “Mute” will appear in the lower-left corner of the
screen.
2
To turn mute off, press the MUTE button again, or simply press
either the VOL – or VOL + button.
3.6
CHAPTER THREE: TV OPERATION
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Clock
1
Press the MENU button to
display the on-screen
menu.
Press the CH ▼ button
three times to select
"Function".
Press the VOL + button.
2
Press the CH ▼ button to
select the “Time” menu.
Press the VOL + button:
The Time menu will
appear on the screen, and
“Clock” will be selected.
When selecting the hours, be sure
to select the proper time of day (AM
or PM).
3
Press the VOL + button
again (the hours digits will
be selected). Press the CH
▲ or CH ▼ button repeat-
edly until the correct hour
appears.
You can change the hours by pressing
CH ▲ or CH ▼ repeatedly (or by
holding down either of these buttons).
After the hour is entered,
press the VOL + button.
(at this point the minutes
digits will be selected).
The time will appear every time
you press DISPLAY.
4
Press the CH ▲ or CH ▼
button to select the
correct minutes.
After selecting the correct
minutes, press the VOL +
button.
Press the MENU button
three times to exit.
CHAPTER THREE: TV OPERATION
3.7
Download from Www.Somanuals.com. All Manuals Search And Download.
Custom izing the Picture
You can use the on-screen menus to change the contrast, brightness, tint, color, and
sharpness according to personal preference. (Alternatively, you can use one of the
“automatic” settings. See next page.)
1
Press the MENU button to
display the menu.
2
Press the VOL – or VOL +
button repeatedly, until the
word “Custom” is selected.
(When Custom is highlight-
ed, the word “Adjust” will
appear on the screen.)
Note: Sharpness and tint can’t be
adjusted in DVD mode.
3
Press the CH ▼ button to
select “Adjust”, then
press the VOL+ button.
(The words Color Tone,
Contrast, Brightness,
Sharpness, Color, and Tint
will appear on the screen.)
Press the CH ▲ or CH ▼
button to select a particu-
lar item.
After adjusting an item, the gauge
4
will automatically disappear (after
about 5 seconds).
Press the VOL – or VOL +
button to increase or
decrease the value of a
particular item.
Press the MENU button
four times to exit.
3.8
CHAPTER THREE: TV OPERATION
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Autom atic Picture Settings
Your TV has three automatic picture settings (“Standard”, “Natural”, and “Mild”) that are
preset at the factory. You can activate either Standard, Natural or Mild by making a
selection from the menu. Or, you can select “Custom” which automatically recalls your
personalized picture settings.
1
Press the MENU button to
display the menu.
2
Press the VOL - or VOL +
button to select the
“Standard,” “Natural,”
“Mild,” or “Custom”
picture setting.
•
•
•
Choose Standard for the standard factory settings.
Natural: Optimal indoor screen condition.
Choose Mild (“Mild Contrast”) when viewing the TV in low light, or when
playing video games.
•
Choose Custom if you want to adjust the settings according to personal pref-
erence (see “Customizing the Picture, page 3.8).
CHAPTER THREE: TV OPERATION
3.9
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Autom atic Sound Settings
Your TV has four automatic sound settings (“Standard,” “Music,” “Movie,” and “Speech”)
that are preset at the factory. You can activate any of them by making a selection from the
on-screen menu.
1
Press the MENU button to
display the menu.
Press the CH▼ button to
select the “Sound” menu.
2
Press the VOL - or VOL +
button repeatedly to
select the “Standard,”
“Music,” “Movie,” or
“Speech” sound settings.
•
•
•
•
Choose Standard for the standard factory settings.
Choose Music when watching music videos or concerts.
Choose Movies when watching movies.
Choose Speech when watching a show that is mostly dialogue (i.e., news).
3.10
CHAPTER THREE: TV OPERATION
Download from Www.Somanuals.com. All Manuals Search And Download.
View ing a VCR or Cam corder Tape
You must select the appropriate mode in order to view the VCR or Camcorder signal
on the TV.
Quick way to view the external
signal: Simply press the TV/VIDEO
button on the remote control.
1
Press the MENU button to
display the menu.
Press the CH ▼ button
twice to select
“Channel”, then press the
VOL+ button.
2
Press the CH ▼ button
twice to select “TV/AV”.
3
Press the VOL+ or VOL-
button.
You will switch between
viewing the signals com-
ing from equipment con-
nected to the TV’s A/V
jacks, and the TV signal.
4
Press the MENU button
twice to exit.
CHAPTER THREE: TV OPERATION
3.11
Download from Www.Somanuals.com. All Manuals Search And Download.
Custom izing Your Rem ote Control
(TXN2022)
Your TV comes equipped with a “universal” remote control. In addition to
controlling the TV, the universal remote can also operate a VCR, DVD and a cable box
(even if your VCR, DVD and cable box are made by manufacturers other than Samsung).
Setting Up Your Rem ote Control to Operate Your VCR or DVD
1
Turn off your VCR or
DVD.
2
On your Samsung remote control, press SET.
The remote control has four
“modes”: “TV,” “VCR”, “DVD” and
“Cable” Press the “VCR” or “DVD”
button to switch the remote control
3
Press the VCR or DVD button on the top right of your remote
control.
to the “VCR” or “DVD” mode.
Make sure you enter both digits of
the code, even if the first digit is a “0.”
If more than one code listed, try the
first one.
4
Enter both digits of the VCR or DVD code listed on the next
page for your brand of VCR or DVD.
If your VCR or DVD does not turn
on, repeat steps 2, 3, and 4, but try
one of the other codes listed for the
brand of your particular VCR or DVD.
5
Press the POWER button on the remote control. Your VCR
or DVD should turn on. If your VCR or DVD turns on, your
remote control is now set correctly.
If no other codes are listed, try each
code, 00 through 72.
When your remote control is in the
“VCR” or “DVD” mode, the volume but-
tons still control your TV’s volume.
6
Once your remote control is set up, press the VCR or DVD
button any time you want to use the remote to operate your
VCR or DVD.
When your remote is in the “TV” mode,
the VCR control buttons (PLAY, STOP,
etc.) will still operate your VCR.
4.1
CHAPTER FOUR: SPECIAL FEATURES
Download from Www.Somanuals.com. All Manuals Search And Download.
VCR Codes
DVD Codes
CHAPTER FOUR: SPECIAL FEATURES
4.2
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up Your Remote Control to Operate Your Cable Box
1
Turn off your
cable box.
2
On your Samsung remote control, press SET.
The remote control has four
“modes”: “TV,” “VCR,” “DVD” and
“CABLE”.
3
Press the CABLE button on the top right of your remote
control.
Press the “CABLE” button to switch
the remote control to the “Cable”
mode.
Make sure you enter both digits
of the code, even if the first digit is a
“0.” (If more than one code listed,
try the first one.)
4
Enter both digits of the cable box code listed below for your
brand of cable box.
If your cable box does not turn
on, repeat steps 2, 3, and 4, but try
one of the other codes listed for your
particular brand of cable box. (If no
other codes are listed, try each cable
box code, 00 through 35.)
5
Press POWER. Your cable box should turn on. If your cable
box turns on, your remote control is now “set up” correctly.
When your remote control is
in the “CABLE” mode, the volume
buttons still control your TV’s vol-
ume. Also, the VCR control buttons
(PLAY, STOP, etc.) will still operate
your VCR.
6
Once your remote control is set up, press the CABLE button
any time you want to use the remote to operate your cable
box.
Cable Box Codes
4.3
CHAPTER FOUR: SPECIAL FEATURES
Download from Www.Somanuals.com. All Manuals Search And Download.
Fine Tuning Channels
Use fine tuning to manually adjust a particular channel for optimal reception.
1
Select the appropriate
channel.
Press the MENU button to
display the menu.
Press the CH ▼ button
twice to select the
“Channel” menu, then
press the VOL+ button.
2
Press the CH ▼ button
three times to select “Fine
tune”, then press the
VOL+ button.
3
Press the VOL+ and VOL-
buttons to adjust the fine
tuning.
Press the MENU button to
resume normal viewing.
4
To store the fine tuning
setting in the TV’s memo-
ry, press the CH ▼ button
to select “Select”.
Press the VOL+ or VOL-
button to select “Added”.
To reset the fine tuning to
“00”, press the VOL+ or
VOL- button to select
“Erased”.
CHAPTER FOUR: SPECIAL FEATURES
4.4
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Screen Size
1
Press the MENU button to
display the menu.
Press the VOL + button to
select the “Picture” menu.
2
Press the CH ▼ button
twice to select "Size."
3
Press the VOL + or VOL -
button repeatedly to
select “Normal” or
“Zoom”.
Press the MENU button
twice to exit.
•
•
Normal : Sets the picture to 4:3 normal mode. This is a standard TV screen size.
Zoom : Magnifies the size of the picture on-screen.
4.5
CHAPTER FOUR: SPECIAL FEATURES
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Surf Feature
This feature allows you to set the TV to return to a particular channel after a certain
amount of time. For example, you may be watching a channel when commercials
start. You can set the Surf to “5 minutes”, then switch channels. After 5 minutes,
the TV will return to the original channel. To use the Surf feature:
1
While you are watching
the channel to which you
want to return, press the
SURF button. The on-
screen display will read
“Surf off”.
2
Press the SURF button
again to set the timer in
thirty second intervals, up
to five minutes.
3
The time you set will begin counting down on the screen.
When the time runs out, the TV will return to the channel
you were watching when you set the timer.
CHAPTER FOUR: SPECIAL FEATURES
4.6
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the On/ Off Tim er
Before using the timer, you must
set the TV’s clock. (See “Setting the
Clock” on page 3.7).
1
Press the MENU button to
display the menu.
Press the CH ▼ button
three times to select
"Function" menu, then
press the VOL+ button.
2
Press the CH ▼ button to
select "Time", then press
the VOL+ button.
When you set the hours, make
sure the correct time of day (AM or
PM) appears to the right of the hour.
3
Press the CH ▼ button to
select "On time".
Press the VOL+ button to
select the “On time”
hours.
(The hours digits will be
highlighted.)
Press the CH ▲ or CH ▼
button repeatedly to
select the appropriate
hours (i.e., the hour when
the TV will turn on.)
4
Press VOL+ to select the
“On time” minutes.
(The minutes digits will be
highlighted.)
Press CH ▲ or CH ▼ to
select the appropriate
minutes.
4.7
CHAPTER FOUR: SPECIAL FEATURES
Download from Www.Somanuals.com. All Manuals Search And Download.
To deactivate the “On time,”
select “Off” during this step.
5
Press the VOL + button to
select “On/Off.”
Press the CH ▲ (or CH ▼)
button to turn the on-
timer “On.” (Repeatedly
pressing the CH ▲ or
CH ▼ button will alter-
nate between on and off.)
6
When finished, press the
VOL + button.
7
To set the Off time, press
the CH ▼ button to
select “Off time.”
Press the VOL + button
and set the hours and
minutes. (Follow the same
procedure as in steps 1~6
above.)
8
When finished setting the timer, press the MENU button three
times to exit.
Setting the Sleep Tim er
The sleep timer automatically shuts off the TV after a preset time
(from 10 to 180 minutes).
After about 5 seconds, the sleep
display will disappear from the
screen, and the time interval will be
set.
1
Press the SLEEP button on the remote control.
2
Press the SLEEP button repeatedly until the appropriate time
interval appears (any of the preset values from “Off” to “180”).
CHAPTER FOUR: SPECIAL FEATURES
4.8
Download from Www.Somanuals.com. All Manuals Search And Download.
Sound Features
Choosing a Multi-Channel Sound (MTS) Soundtrack
Depending on the particular program being broadcast, you can listen to Stereo, Mono or
a Separate Audio Program. (SAP audio is usually a foreign-language translation.
Sometimes SAP has unrelated information like news or weather.)
1
Press the MENU button
to display the menu.
Press the CH▼ button to
select the “Sound” menu,
then press the VOL+ but-
ton.
2
Press the CH▼ button
four times to select
“MTS”.
The text at the bottom of the
menu tells you if the incoming
audio is stereo, SAP, or mono.
3
Press the VOL + or VOL -
button to select “Mono,”
“SAP,” or “Stereo.”
Press the MENU button
twice to exit
•
•
Choose Stereo for channels that are broadcasting in stereo.
Choose Mono for channels that are broadcasting in mono, or if you are
having difficulty receiving a stereo signal.
•
Choose SAP to listen to the Separate Audio Program, which is usually a
foreign-language translation.
You can also change the MTS setting by pressing the “MTS” button on the remote
control. (When you change channels, MTS is set to “Stereo” automatically.
To listen in ‘SAP’ or ‘Mono,’ change the MTS setting.)
4.9
CHAPTER FOUR: SPECIAL FEATURES
Download from Www.Somanuals.com. All Manuals Search And Download.
Extra sound settings (Turbo Sound, or Surround)
• Turbo Sound
Turbo sound emphasizes the bass and treble frequencies to add fullness to the sound.
• Surround
Your Samsung TV creates a "Surround" effect such that the sound seems to come from all
directions. Once the “Surround” is set to “On” or “Off”, the setting applies to the sound
effects such as Standard, Music, Movie and Speech.
Note: To listen a “Surround” effects, it is necessary that channels are broadcasting in
stereo. and setting the MTS to stereo mode.
1
Press the MENU button to
display the menu.
Press the CH▼ button to
select the “Sound” menu,
then press the VOL + but-
ton.
2
Press the CH▼ button
three times to select
“Turbo sound”.
3
Press the VOL + button to
select “On”.
Press the MENU button
twice to exit
You can set Surround as the same way of setting Turbo sound.
CHAPTER FOUR: SPECIAL FEATURES
4.10
Download from Www.Somanuals.com. All Manuals Search And Download.
View ing Closed Captions
Your TV decodes and displays the closed captions that are broadcast with certain TV shows.
These captions are usually subtitles for the hearing impaired or foreign-language trans-
lations. All VCRs record the closed caption signal from television programs, so home-record-
ed video tapes also provide closed captions. Most pre-recorded commercial video tapes pro-
vide closed captions as well. Check for the closed caption symbol in your television schedule
and on the tape’s packaging:
.
1
Press the MENU button to
display the menu.
Press the CH ▼ button
three times to select the
“Function” menu.
Press the VOL+ button.
2
Press the CH ▼ button
twice to select the
“Caption” menu, then
press the VOL+ button.
Misspellings and unusual
characters sometimes occur during
closed caption transmissions, especial-
ly those of live events. There may be a
small delay before captions appear
when you change channels. These are
not malfunctions of the TV.
3
Press the VOL+ or VOL –
button to turn closed cap-
tioning on/off.
In caption mode, captions
appear at the bottom of the screen,
and they usually cover only a small
portion of the picture.
4
Press the CH ▼ button to
select “Mode.”
In text mode, information unrelated
to the program, such as news or
weather, is displayed. Text often
covers a large portion of the screen.
Press the VOL – or VOL +
button to select “Caption”
or “Text.”
Different channels and fields
display different information: Field 2
carries additional information that
supplements the information in
Field 1. (For example, Channel 1
may have subtitles in English, while
Channel 2 has subtitles in Spanish.)
5
Depending on the particular broadcast, it might be necessary to
make changes to “Channels” and “Field”:
Use the CH ▲, CH ▼, VOL + and VOL - buttons to make the
changes. (Follow the same procedure as in steps 3~4 above.)
Press the MENU button three times to exit.
4.11
CHAPTER FOUR: SPECIAL FEATURES
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the V-Chip
The V-Chip feature automatically locks out programming that is deemed inappropriate for
children. The user must first enter a PIN (personal ID number) before any of the V-Chip
restrictions can be set up or changed.
Note : When the V-chip feature is active, channel-auto program features do not function.
Setting Up Your Personal ID Num ber (PIN)
1
Press the MENU button to
display the menu.
Press the CH ▼ button
three times to select the
“Function” menu.
Press the VOL+ button.
2
Press the CH ▼ button
three times to select the
“V-chip” menu.
Press the VOL+ button.
The “Enter pin” screen will appear. Enter your 4-digit PIN
number. Note: The default PIN number for a new TV set is
“0-0-0-0.”
3
After entering a valid PIN
number, the “V-chip”
screen will appear.
Press the CH ▼ button
three times and highlight
“Change pin.”
Note: If you forget the PIN,
press the remote-control keys in the
following sequence, which resets the
pin to 0-0-0-0:
4
While the “Change pin”
field is selected, press the
VOL+ button. The Change
pin screen will appear.
Choose any 4-digits for
your PIN and enter them.
POWER OFF ➜ MUTE ➜ 8 ➜ 2 ➜
4 ➜ POWER ON.
As soon as the 4 digits are entered, the “Confirm new pin”
screen appears. Re-enter the same 4 digits. When the Confirm
screen disappears, your PIN has been memorized.
Press the MENU button three times to exit.
CHAPTER FOUR: SPECIAL FEATURES
4.12
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Enable/ Disable the V-Chip
1
Press the MENU button to
display the menu.
Press the CH ▼ button
three times to select the
“Function” menu.
Press the VOL+ button.
2
Press the CH ▼ button
three times to select the
“V-chip” menu.
Press the VOL+ button.
The “Enter pin” screen
will appear. Enter your 4-
digit PIN number.
3
The “V-Chip” screen will
appear, and “V-Chip lock”
will be selected (turns blue
color).
To enable the V-Chip fea-
ture, press the VOL + but-
ton so that the “V-Chip
lock” field is Yes. (Pressing
VOL+ will alternate
between Yes and No.)
How to Set up Restrictions Using the “TV guidelines”
First, set up a personal identification number (PIN), and enable the V-Chip. (See previous
section.) Parental restrictions can be set up using either of two methods: The TV guide-
lines or the MPAA rating.
1
Press the MENU button to
display the menu.
Press the CH ▼ button
three times to select the
“Function” menu.
Press the VOL+ button.
4.13
CHAPTER FOUR: SPECIAL FEATURES
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Press the CH ▼ button
three times to select the
“V-chip” menu.
Press the VOL+ button.
The “Enter pin” screen
will appear. Enter your 4-
digit PIN number.
3
The “V-chip” screen will
appear. Press the CH ▼
button, and highlight the
field for “TV guidelines.”
Note: These categories consist of
two separate groups: TV-Y and TV-Y7
(young children through age 7), and
TV-G through TV-MA (everybody
else).
4
Press the VOL+ button.
The “TV guidelines”
screen will appear. Press
the CH ▲, CH ▼ buttons
to highlight one of the six
age-based categories:
The restrictions for these two groups
work independently: If a household
includes very young children as well
as young adults, the TV guidelines
must be set up separately for each age
group. (See next step.)
TV-Y
TV-Y7
Young children
Children 7 and over
--------------------------------------
TV-G General audience
TV-PG Parental guidance
TV-14 Viewers 14 and over
TV-MA Mature audience
5
At this point, one of the TV-Ratings is highlighted (blue color).
Press the VOL+ button: Depending on your existing setup, a letter “U” or “B” will start blinking.
(U= Unblocked, B= Blocked)
While the “U” or ”B” is red, press the CH ▲ or CH ▼ button to block or unblock the category.
Press the MENU button once to save the TV guidelines. A TV-Rating will be highlighted, and no letters will blink.
To exit this screen, press MENU again. To select a different TV-Rating, press the CH ▲ or CH ▼ button and then
repeat the process.
Note 1: The TV-Y7, TV-PG, TV-14 and TV-MA have additional options. See the next step to change any of the
following sub-ratings:
FV: Fantasy violence
D: Dialog
L: Offensive language
S: Sexual situation
V: Violence
Note 2: The V-Chip will automatically block certain categories that are “more restrictive.” For example, if you block
“TV-Y” category, then TV-Y7 will automatically be blocked. Similarly, if you block the TV-G category, then all the
categories in the “young adult” group will be blocked (TV-G, TV-PG, TV-14 and TV-MA). The sub-ratings (D, L, S, V)
work together similarly. (See next section.)
CHAPTER FOUR: SPECIAL FEATURES
4.14
Download from Www.Somanuals.com. All Manuals Search And Download.
6
How to set the FV, D, L, S and V sub-ratings:
First, highlight one of these TV-Ratings: TV-Y7, TV-PG, TV-14 or TV-MA (See Step 4, on previous page).
Next, while the TV-Rating is highlighted (BLUE), repeatedly press the VOL + button. This will cycle through
the available sub-ratings (FV,L, S, D or V).
A blinking letter (“U” or “B”) will be displayed for each sub-rating. While the “U” or “B” is blinking, press
the CH ▲ or CH ▼ button to change the sub-rating.
Press MENU once to save the TV guidelines. A TV-Rating will be highlighted (BLUE), and no letters will blink.
To exit this screen, press MENU again. To select a different TV-Rating, press the CH ▲ or CH ▼ button and
then repeat the process.
Note: The V-chip will automatically block certain categories that are “More restrictive”. For example, if you
block “L” sub-rating in TV-PG, then the “L” sub-ratings in TV-14 and TV-MA will automatically be blocked.
7
Press the MENU button three times to clear all the screens. (Or proceed to the next section, and set up
additional restrictions based on the MPAA codes).
How to Set up Restrictions using the MPAA Ratings: G, PG, PG-
13, R, NC-17, X
The MPAA rating system uses the Motion Picture Association of America (MPAA) system,
and its main application is for movies. (Eventually, movie videocassettes will be encoded
with MPAA ratings.) When the V-Chip lock is on, the TV will automatically block any
programs that are coded with objectionable ratings (either MPAA or TV-Ratings).
1
Press the MENU button to
display the menu.
Press the CH ▼ button
three times to select the
“Function” menu.
Press the VOL+ button.
2
Press the CH ▼ button
three times to select the
“V-chip” menu.
Press the VOL+ button.
The “Enter pin” screen
will appear. Enter your 4-
digit PIN number.
4.15
CHAPTER FOUR: SPECIAL FEATURES
Download from Www.Somanuals.com. All Manuals Search And Download.
3
The “V-chip” screen will
appear.
Press the CH ▼ button
twice, and select “MPAA
rating.”
4
While “MPAA rating” is
selected, press the VOL+
button. The “MPAA rat-
ing” screen will appear.
G
General audience (no restrictions).
Parental guidance suggested.
5
PG
Repeatedly press the CH
▼ button to select a
particular MPAA category.
Pressing the CH ▼ button
will cycle through the
MPAA categories:
PG-13 PG-13 (Parents strongly cautioned).
R
R (Restricted. Children under 17 should
be accompanied by an adult).
NC-17 No children under age 17.
X
X (Adults only).
Not rated.
NR
While a particular category is selected, press VOL+ to activate it.
A letter (“U” or “B”) will be displayed. Press CH ▲ or CH ▼ to select “U” or”B”.
Press MENU four times to save the settings and to clear all screens.
Note: The V-Chip will automatically block any category that is “more restrictive.” For example, if you
block the “PG-13” category, then “R,” “NC-17,” and “X” will automatically be blocked also.
How to Reset the TV after the V-Chip
Blocks a Channel (“Em ergency Escape”)
If the TV is tuned to a restricted channel, the V-Chip will block it. The screen will go blank and the following
message will appear: “Excessive rating.”
To resume normal viewing, tune to a different channel using the number buttons. Under certain conditions
(depending on the rating of the local TV programs) the V-Chip might lock out all the channels. In this case,
use the V-Chip function for an “emergency escape”:
Press the MENU button to display the menu. Press the CH ▼ button three times to select the “Function”
menu and press the VOL + button.
Press the CH ▼ button three times to highlight the “V-chip” menu and press the VOL + button.
Enter your PIN number, and press the VOL + button to temporarily disable the V-Chip Lock.
CHAPTER FOUR: SPECIAL FEATURES
4.16
Download from Www.Somanuals.com. All Manuals Search And Download.
If the TV seems to have a problem, first try this list of possible problems and solutions.
If none of these troubleshooting tips apply, then call your nearest Samsung authorized
service center.
Identifying Problem s
CHAPTER FIVE: TROUBLESHOOTING
5.1
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and Maintaining Your TV
With proper care, your TV unit will give you many years of service. Please follow these
guidelines to get the maximum performance from your TV.
Placem ent
•
•
Do not place the TV near extremely hot, cold, humid or dusty places.
Do not place the TV near appliances with electric motors that create magnetic fields,
such as vacuum cleaners.
•
Keep the ventilation openings clear; do not place the TV on a soft surface, such as
cloth or paper.
•
Place the TV in a vertical position only.
Liquids
•
Do not handle liquids near or on the TV. Liquids that spill into it can cause serious
damage.
Cabinet
•
•
Never open the cabinet or touch the parts inside.
Wipe your TV with a clean, dry cloth. Never use water, cleaning fluids, wax, or
chemicals.
•
Do not put heavy objects on top of the cabinet.
Tem perature
•
If your TV is suddenly moved from a cold to a warm place, unplug the power cord,
and allow at least two hours for moisture that may have formed inside the unit to dry
completely.
Using Your TV in Another Country
If you plan to take your TV with you to a foreign country, please be aware of the different
television systems that are in use around the world. A TV designed for one system may
not work properly with another system due to differences in the TV channel frequencies.
Specifications
TXN1430F / TXN1634F / TXN2022
Model
AC 120V
60Hz
Voltage
Frequency of Operation
A.1APPENDIX
Download from Www.Somanuals.com. All Manuals Search And Download.
|