O W N E R ’ S
O P E R A T I N G
M A N U A L
85
1080p DLP™ PROJECTORS
Vision 85
Vision 85/CineWide™
Download from Www.Somanuals.com. All Manuals Search And Download.
TWO YEAR LIMITED WARRANTY
For Projectors, Video Processors and Controllers
Congratulations on your purchase of a Vidikron video product and welcome to the Vidikron family! With proper installation, setup
and care, you should enjoy many years of unparalleled video performance.
This is a LIMITED WARRANTY as defined in the Magnuson-Moss Warranty Act. Please read it carefully and retain it with your other
important documents.
WHAT IS COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY:
SERVICE LABOR: Vidikron will pay for service labor by Vidikron Authorized Service Center when needed as a result of manufacturing
defect for a period of two (2) years from the effective date of delivery to the end user (excluding the lamp).
PARTS (not including the lamp): Vidikron will provide new or rebuilt replacement parts for the parts that fail due to defects in
materials or workmanship for a period of two (2) years from the effective date of delivery to the end user. Such replacement parts
are then subsequently warranted for the remaining portion (if any) of the original warranty period.
PROJECTOR LAMP: Vidikron will pay for service labor by a Vidikron Authorized Service Center when needed as a result of a
manufacturing defect for a period of six (6) months or 1000 hours, whichever comes first, from the effective date of delivery to the
end user. In addition, Vidikron will provide a new or rebuilt replacement lamp for the lamp that fails due to defects in materials or
workmanship for a period of six (6) months or 1000 hours, whichever comes first, from the effective date of delivery to the end user.
Such replacement lamps are then subsequently warranted for the remaining portion (if any) of the original warranty period.
WHAT IS NOT COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY:
This Limited Warranty only covers failure due to defects in materials and workmanship that occur during normal use and does not
cover normal maintenance. This Limited Warranty does not cover cabinets or any appearance items; failure resulting from
accident, misuse, abuse, neglect, mishandling, misapplication, faulty or improper installation or setup adjustments; improper
maintenance, alteration, improper use of any input signal; damage due to lightning or power line surges, spikes and brownouts;
damage that occurs during shipping or transit; or damage that is attributed to acts of God. In the case of remote control units,
damage resulting from leaking, old, damaged or improper batteries is also excluded from coverage under this Limited Warranty.
CAUTION: THIS LIMITED WARRANTY ONLY COVERS VIDIKRON PRODUCTS PURCHASED FROM VIDIKRON AUTHORIZED DEALERS.
ALL OTHER PRODUCTS ARE SPECIFICALLY EXCLUDED FROM COVERAGE UNDER THIS WARRANTY. MOREOVER, DAMAGE
RESULTING DIRECTLY OR INDIRECTLY FROM IMPROPER INSTALLATION OR SETUP IS SPECIFICALLY EXCLUDED FROM COVERAGE
UNDER THIS LIMITED WARRANTY. IT IS IMPERATIVE THAT INSTALLATION AND SETUP WORK BE PERFORMED ONLY BY AN
AUTHORIZED VIDIKRON DEALER TO PROTECT YOUR RIGHTS UNDER THIS WARRANTY. THIS WILL ALSO ENSURE THAT YOU ENJOY
THE FINE PERFORMANCE OF WHICH YOUR VIDIKRON PRODUCT IS CAPABLE WHEN INSTALLED AND CALIBRATED BY VIDIKRON
AUTHORIZED PERSONNEL.
RIGHTS, LIMITS AND EXCLUSIONS:
Vidikron limits its obligations under any implied warranties under state laws to a period not to exceed the warranty period. There
are no express warranties. Vidikron also excludes any obligation on its part for incidental or consequential damages related to the
failure of this product to function properly. Some states do not allow limitations on how long an implied warranty lasts, and some
states do not allow the exclusion or limitation of incidental or consequential damages. So the above limitations or exclusions may
not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.
Vidikron Vision 85 Owner’s Operating Manual
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
EFFECTIVE WARRANTY DATE:
This warranty begins on the effective date of delivery to the end user. For your convenience, keep the original bill of sale as
evidence of the purchase date.
IMPORTANT -- WARRANTY REGISTRATION:
Please fill out and mail your warranty registration card. It is imperative that Vidikron knows how to reach you promptly if we should
discover a safety problem or product update for which you must be notified.
CONTACT A VIDIKRON AUTHORIZED SERVICE CENTER TO OBTAIN SERVICE:
Repairs made under the terms of this Limited Warranty covering your Vidikron video product will be performed at the location of
the product, during usual working hours, providing location of product is within normal operating distance from a Vidikron
Authorized Service Center. In some instances it may be necessary for the product to be returned to the Vidikron factory for repairs.
If, solely in Vidikron’s judgment, location of product to be repaired is beyond normal operating distance of the closest Vidikron
Authorized Service Center, or the repair requires the unit be returned to the Vidikron factory, it is the owner’s responsibility to
arrange for shipment of the product for repair. These arrangements must be made through the selling Vidikron Dealer. If this is not
possible, contact Vidikron directly for a Return Authorization number and shipping instructions. Vidikron will return product
transportation prepaid in the United States, unless no product defect is discovered. In that instance, shipping costs will be the
responsibility of the owner.
COPYRIGHT AND TRADEMARKS:
© Copyright 2007 Vidikron, a Runco International Company. This document contains proprietary information protected by
copyright, trademark and other intellectual property laws. All rights are reserved. No part of this manual may be reproduced by any
mechanical, electronic or other means, in any form, without prior written permission of the manufacturer.
2
Vidikron, Vision, DVSI, Imagix, CineWide, AutoScope, V Aperture Control, CSMS and IntelliWide are trademarks of Runco, LLC. All
other trademarks and registered trademarks used in this document are the property of their respective owners.
Vidikron products are manufactured under one or more of the following patents: US. Patent 6755540 and Other Patents Pending.
iv
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
ADDITIONAL INFORMATION:
To locate the name and address of the nearest Vidikron Authorized Service Center, or for additional information about this Limited
Warranty, please call or write:
VIDIKRON
Attn: Customer Service Department
2900 Faber Street
Union City, CA 94587
Ph: (510) 324-5900
Fax: (510) 324-5905
Toll Free: (888) 4VIDIKRON
VIDIKRON PRODUCT INFORMATION
RETAIN THIS INFORMATION FOR YOUR RECORDS
_________________________________________________________
Model Purchased
________________________________________
Date
____________________________________________________________________________________________________________
Serial Number
____________________________________________________________________________________________________________
Vidikron Authorized Dealer Name
____________________________________________________________________________________________________________
Address
____________________________________________
__________________
State/Province
________________________
Postal Code
City
____________________________________________
Phone
_______________________________________________________
Fax
Vidikron Vision 85 Owner’s Operating Manual
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions
Thank you for your purchase of this quality Vidikron video projector! It has been designed to provide you with the quality of video
that is expected in a home theater. For the best performance, please read this manual carefully as it is your guide through the
menus and operation.
WARNING
This symbol is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure that
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
may be of sufficient magnitude to constitute a risk of electric shock.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER SERVICEABLE PARTS INSIDE.
This symbol is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Do not use this equipment near water, outdoors or otherwise exposed to the elements.
5. Clean only with a dry cloth.
6. Do not block any ventilation openings.
7. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that
produce heat.
8. Do not defeat the safety feature of the polarized or grounding type plug. A polarized type plug has two blades with one wider
than the other. A grounding type plug has two blades and a third grounding prong. The third prong is provided for your safety.
If the provided plug does not fit into your outlet, consult an electrician for the replacement of the obsolete outlet.
9. The 12V trigger only outputs DC 12V signal for triggering. Do not connect to any other power input or output. This could cause
damage to this unit.
10. Only use accessories specified by Vidikron.
11. Keep the packing material in case the equipment should ever need to be shipped.
12. Unplug this projector during lightning storms or when it will not be used for an extended period of time.
13. The lamp becomes extremely hot during operation. Allow the projector to cool down for approximately 45 minutes prior to
removing the lamp assembly for replacement. Do not operate lamps beyond the rated lamp life. Excessive operation of lamps
beyond rated life could cause them to explode in rare occasions.
14. Refer all servicing to qualified service personnel. Servicing is required when the projector has been damaged in any way,
objects have fallen or spilled into the projector, the projector has been exposed to rain or moisture, does not operate normally,
or has been dropped.
vi
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1Table of Contents
TWO YEAR LIMITED WARRANTY ............................................................................................. iii
Safety Precautions ................................................................................................................... vi
1. Introduction ........................................................................................................................ 1
Description, Features and Benefits ............................................................................................................. 3
2. Controls and Functions ...................................................................................................... 5
Vision 85 at a Glance ........................................................................................................................................ 5
Vision 85 Rear Panel ......................................................................................................................................... 7
VHD Controller Front Panel ........................................................................................................................... 8
VHD Controller Rear Panel ............................................................................................................................. 9
Vision 85 Remote Control Unit ...................................................................................................................11
Vision 85 Built-In Keypad ..............................................................................................................................14
3. Installation ........................................................................................................................15
Remote Control ................................................................................................................................................15
Notes on Remote Control Operation................................................................................................15
Quick Setup .......................................................................................................................................................17
Installation Considerations ..........................................................................................................................18
Installation Type.......................................................................................................................................18
Ambient Light ...........................................................................................................................................18
Throw Distance.........................................................................................................................................19
Vertical and Horizontal Position.........................................................................................................20
Vertical Lens Shift ....................................................................................................................................20
Folded Optics ............................................................................................................................................21
Other Considerations .............................................................................................................................21
Vidikron Vision 85 Owner’s Operating Manual
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the Vision 85 .................................................................................................................................22
Floor Mounting (Upright) .....................................................................................................................22
Ceiling Mounting (Inverted) ................................................................................................................22
Adjusting the Projection Angle ..........................................................................................................22
Connections to the Vision 85 and VHD Controller ..............................................................................23
Connector Panel Access ........................................................................................................................23
Connecting the Projector to the VHD Controller.........................................................................23
Connecting a PC or Automation System to the VHD Controller ............................................28
Connecting 12-Volt Trigger Outputs to External Equipment..................................................28
Connecting an External IR Receiver to the VHD Controller......................................................29
Connecting to AC Power.......................................................................................................................30
Turning on the Power ....................................................................................................................................30
Adjusting the Picture Orientation .............................................................................................................30
Primary Lens Adjustments ...........................................................................................................................31
Focus and Zoom.......................................................................................................................................31
Vertical Lens Shift ....................................................................................................................................31
Installing and Adjusting the CineWide Anamorphic Lens ................................................................32
4. Operation ..........................................................................................................................35
Using the On-Screen Menus ........................................................................................................................35
On-Screen Menus for 1080i (Analog) and Lower-Resolution Signals ...........................................35
Main Menu .................................................................................................................................................37
Input Source ..............................................................................................................................................37
Aspect Ratio ..............................................................................................................................................37
Picture .........................................................................................................................................................39
Input Position............................................................................................................................................43
ISF Presets...................................................................................................................................................44
Information ................................................................................................................................................44
Calibration..................................................................................................................................................45
Service..........................................................................................................................................................47
viii
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
On-Screen Menus for 1080i (Digital) or 1080p Signals ......................................................................51
Main Menu .................................................................................................................................................52
Language....................................................................................................................................................53
Picture Adjust............................................................................................................................................53
White Balance ...........................................................................................................................................56
HD/RGB Adj. ..............................................................................................................................................57
Options........................................................................................................................................................57
5. Maintenance and Troubleshooting ................................................................................61
Lamp Replacement .........................................................................................................................................61
Troubleshooting Tips .....................................................................................................................................62
6. Serial Communications ....................................................................................................65
RS-232 Connection and Port Configuration ..........................................................................................65
Serial Command Syntax ................................................................................................................................65
7. Specifications ....................................................................................................................71
Vision 85 Specifications .................................................................................................................................71
VHD Controller Specifications .....................................................................................................................73
Vision 85 Dimensions .....................................................................................................................................74
Vidikron Vision 85 Owner’s Operating Manual
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
x
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1List of Figures
2-1. Vision 85 Front/Top/Side/Bottom/Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2-2. Vision 85 Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2-3. VHD Controller Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2-4. VHD Controller Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2-5. VHD Controller/Vision 85 Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2-6. Vision 85 Built-In Keypad. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3-2. Estimating Throw Distance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3-6. Connecting the Projector to the VHD Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3-7. HDMI Source Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3-8. Digital (DTV) RGB or Component Video Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3-11. RS-232 Control System Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3-12. 12-volt Trigger Output Connections (from VHD Controller). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3-13. 12-volt Trigger Output Connection (from Projector) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3-16. Vision 85 Anamorphic Lens Mounting Assembly - Exploded View . . . . . . . . . . . . . . . . . . . . . . 32
4-1. VHD Controller OSD Menu Structure for Vision 85
(1080i Analog and Lower-Resolution Sources) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4-5. Typical Test Pattern for Adjusting Sharpness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
4-6. OSD Menu Structure for Vision 85 (1080i Digital or 1080p Sources) . . . . . . . . . . . . . . . . . . . . . . 51
4-7. Vision 85 Main Menu (1080i Digital or 1080p Sources Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
7-1. Vision 85 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Vidikron Vision 85 Owner’s Operating Manual
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
List of Figures
Notes:
xii
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1Introduction
This Owner’s Manual describes how to install, set up and operate the Vidikron Vision 85 DLP
Projector and VHD Controller.
1.1
About This Manual
Throughout this manual, the Vidikron Vision 85 DLP Projector and VHD Controller are
referred to collectively as the “Vision 85.”
Vidikron has prepared this manual to help home theater installers and end users get the
Target Audience
most out of the Vision 85.
Vidikron has made every effort to ensure that this manual is accurate as of the date it was
printed. However, because of ongoing product improvements and customer feedback, it
may require updating from time to time. You can always find the latest version of this and
If You Have Comments About
This Manual...
Text Conventions: The following conventions are used in this manual, in order to clarify the
information and instructions provided:
Textual and Graphic
Conventions
•
•
Remote and built-in keypad button identifiers are set in upper-case bold type; for
example, “Press EXIT to return to the previous menu.”
Computer input (commands you type) and output (responses that appear on-screen) is
shown in monospace (fixed-width) type; for example: “To change the aspect ratio to
Letterbox, type LETTERBOX <Enter>.”
•
All keys with functional names are initial-capped, set in bold type and enclosed in angle
brackets. These keys are the following: <Enter>, <Spacebar>, <Control>,
<Esc>and <Tab>.
• <Enter>indicates that you may press either the RETURN or ENTER key on your keyboard
if it has both keys.
In addition to these conventions, underlining, boldface and/or italics are occasionally used to
highlight important information, as in this example:
A carriage return must be used after each command or string.
Note
Vidikron Vision 85 Owner’s Operating Manual
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Graphic Conventions: These symbols appear in numerous places throughout the manual,
to emphasize points that you must keep in mind to avoid problems with your equipment or
injury:
TIPS highlight time-saving short cuts and helpful guidelines for using
certain features.
Tip
NOTES emphasize text with unusual importance or special significance.
They also provide supplemental information.
Note
CAUTIONS alert users that a given action or omitted action can degrade
performance or cause a malfunction.
Caution
WARNINGS appear when a given action or omitted action can result in
damage to the equipment, or possible non-fatal injury to the user.
WARNING
DANGER!
DANGER appears when a given action can cause severe injury or death.
Use the following table to locate the specific information you need in this manual.
1.2
Using This Manual
If you need...
... Turn to page:
Information about obtaining service
iv
General information about the Vision 85 DLP
Projector and VHD Controller
Installation instructions
17
32
47
64
73
First-time configuration instructions
Advanced configuration instructions
Troubleshooting tips
Product specifications
2
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
The all-new Vision 85 DLP Projector and VHD Controller is the most high performance
single-chip DLP™ 1920 x 1080 projection system available. Its performance is so impressive
that the Vision™ Model 85 earns prestigious THX® certification, joining other Vidikron
products as the world’s first to earn this distinction.
1.3
Description, Features and
Benefits
The Vision™ Model 85 incorporates a state-of-the-art light engine featuring engineering
advancements for more efficient use of optical light engine design. This includes a
sophisticated color balancing system and the industry’s best gray scale tracking. Vidikron’s
exclusive V2 Aperture Control™ enables an ideal balance between black and white levels for
each individual installation.
Vidikron’s exclusive, all-digital Imagix™ video processing is included for the most advanced
video processing, 1080p scaling, and pristine image quality available. The Vision™ Model 85
offers a broad array of video inputs, including HDMI™. Discrete infrared (IR) and RS-232
control make custom installation seamless, while discrete source and aspect ratio selection
accommodate any automation control system.
For uncompromising widescreen reproduction of movies originally filmed in the “scope”
(2.35:1) format, the Vision 85 can be equipped with Vidikron’s patent-pending CineWide™
technology, a combination of software, electronics and high-quality anamorphic optics.
CineWide maintains constant vertical height on the screen just as in a movie theater. When a
viewer transitions from 1.78:1 (16:9) program material to 2.35:1, the image simply gets wider
while full height is maintained.
CineWide requires the use of a 2.35:1 or similar aspect ratio superwide format
screen.
Note
Vidikron Vision 85 Owner’s Operating Manual
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Key Features and Benefits
The Vision 85 offers these key features and benefits:
➤
2
•
•
•
Vidikron-engineered, Enhanced GEN 3 Technology™ with V AC
Native Resolution: 1920 x 1080 (16:9 Native Aspect Ratio)
Two HDMI Inputs (on VHD Controller) with High-bandwidth Digital Content Protection
(HDCP)
•
HDTV Compatible
Parts List
Your Vision 85 is shipped with the following items. If any items are missing or damaged,
please contact your Vidikron dealer or Vidikron Customer Service at (888) 4VIDIKRON.
➤
•
•
•
•
•
•
•
•
Vision 85 DLP Projector and VHD Controller
Remote Control Unit and two (2), AAA-size batteries
AC Power Cords (2)
RJ-11 Telephone Cable, 50 feet (15.24 meters)
9/64” Hex Wrench (for lens adjustments)
Rack-mount hardware for the VHD Controller
Warranty information and registration card
Vidikron Vision 85 Owner’s Operating Manual (this document)
Optional Accessories:
•
•
CineWide™ technology (fixed, secondary anamorphic lens)
Ceiling mount kit
4
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1. VERTICAL LENS SHIFT
Using a 9/64” hex wrench, turn this to move the lens up or down.
2. POWER LED
Lights red to indicate that the projector is in standby; flashes blue during warm-up or
cool-down or lights blue to indicate normal operation.
3. LAMP LED
Lights blue to indicate normal lamp operation; lights red if the lamp has failed.
4. TEMP LED
Lights red to indicate that the projector has overheated and shut down.
5. EXHAUST VENTS
Hot air exits the projector through these vents. This air can be quite hot. Ensure that
there are no heat-sensitive objects near it and that it is never blocked.
6. CABLE OPENING
Pass cables through this opening.
7. INTAKE VENTS
Cool air enters the projector through these vents. To prevent overheating, ensure that
these vents are never blocked.
8. ZOOM TAB
Turn this tab to make the projected image larger or smaller.
9. VIDIKRON LOGO
You can rotate the logo to match the projector orientation: inverted (ceiling-mounted)
or upright. To rotate the logo, grip it at the sides, pull it away from the projector and
rotate it 180 degrees.
10. FOCUS RING
Turn this ring to focus the image.
11. LAMP COVER
Remove this cover to access the lamp compartment.
12. REAR PANEL ACCESS DOOR
To access the connector panel,
press the door release button so it
pops out. Turn the knob clockwise
or counter-clockwise and pull
gently on it to open the door.
6
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2
Vision 85 Rear Panel
T I O R A
A S P E C T
R E T U R N E N T E R
D O W N U P
L E F T
R I G H T
M E N U
A N S D T B Y
O N
RETURN ENTER
DOWN
UP
LEFT
RIGHT
MENU
ASPECT
RATIO
STANDBY
ON
H D M I
HDMI
T R I G G E R I R
IR
R S - 2 3 2 O U T
RS-232 OUT
A C I N 1 0 0 - 2 4 0 V 5 0 - 6 0 H z
TRIGGER
AC IN 100-240V 50-60Hz
1
2
3
4
5
6
Figure 2-2. Vision 85 Rear Panel
1. POWER INPUT (100 to 240 VAC)
Connect the Vision 85 to power here.
2. HDMI INPUT
An HDCP-compliant, digital video input for connecting the HDMI output from the VHD
Controller.
3. BUILT-IN KEYPAD
page 14 for more information.
4. 12-VOLT (200 mA) TRIGGER OUTPUT (cylindrical, DC power supply-type jack)
Connection for a retractable screen, screen masking or other, 12-volt trigger-activated
equipment. Outputs +12 volts/200 mA when the projector is turned on.
5. WIRED IR (3.5-mm, mini phono jack)
Not used. To use an external infrared receiver or wired remote control with this
6. RS-232C INPUT (RJ-11 female connector)
Connect the RS-232 output from the VHD Controller here, using the provided
communication cable.
Vidikron Vision 85 Owner’s Operating Manual
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2-3 shows the controls and indicators on the VHD Controller front panel; the
paragraphs that follow describe them.
2.3
VHD Controller Front
Panel
Component SD NTSC
16:9
480i
V85
1
2
3
Figure 2-3. VHD Controller Front Panel
1. POWER BUTTON
Press once to toggle from standby mode to on mode. Press it again to return to standby
mode. For a discrete on or off command, you can use the direct access buttons on the
remote control.
2. IR SENSOR
Receives IR commands from the remote.
3. VACUUM FLUORESCENT DISPLAY
Can be used instead of the On-Screen Display (OSD). Displays currently-selected menu
or – if no menu is selected – the current source, signal format (NTSC or PAL), input
resolution and aspect ratio.
8
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2-4 shows the rear connector panel on the VHD Controller.
2.4
VHD Controller Rear Panel
3
7
9
SYSTEM CONTROL INTERFACE
CAUTION
RISK OF ELECTRIC SHOCK
Serial No
INPUTS
B/Pb
!
DO NOT OPEN
R/Pr
G/Y
H
V
AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
TRIGGERS
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER. NO USER-
SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE CENTER.
HD1
HD2
1
2
3
IR
Model
Video Processor Controller
/
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
R/Pr
G/Y
B/Pb
H
V
Pb
Pr
Y
S-Video
S-Video
1
2
100-230VAC 50-60 Hz, 165 Watts Max
Made In USA
HDMI Out
HDMI
1
HDMI
2
Component Video
Video
RS-232 Out
RS-232 Control
1
2
8
10
11
4
5
6
12
13
Figure 2-4. VHD Controller Rear Panel
1. HDMI OUT
Outputs
Inputs
2. HDMI 1 / HDMI 2 (Digital)
Two, HDCP-compliant digital video inputs for connecting a DVD player or HD tuner with
a DVI or HDMI output.
3. HD1 / HD2 (5 x Analog BNCs)
Two inputs (five BNCs per input) for connecting either RGB or component
high-definition television signals. The VHD Controller automatically detects the signal
format: RGB(HV) or YPrPb, 480p, 720p, 480i, 576i or 1080i.
4. COMPONENT VIDEO (RCA connectors)
Standard Definition (480i/576i) Component (YPrPb) input. This is the input for
component video from sources such as DVD players.
For best results, do not run your DVD player in progressive mode.
Tip
Vidikron Vision 85 Owner’s Operating Manual
9
Download from Www.Somanuals.com. All Manuals Search And Download.
5. COMPOSITE VIDEO INPUT
Standard composite video input for connecting a VCR, laser disc player or other
composite video source.
6. S-VIDEO 1 / S-VIDEO 2
Two, standard S-Video inputs for connecting a DVD player, satellite receiver or Super
VHS (S-VHS) VCR.
7. 12-VOLT (750 mA) TRIGGER OUTPUTS
Connection for up to three (3), 12-volt trigger-controlled devices such as retractable
screens or screen masks.
8. ComLink (RS-232) OUTPUT
Connect this to the ComLink (RS-232) input on the projector, using the provided
communication cable.
9. IR
Wired input from a wired remote control or infrared receiver. It is a 3.5-mm, mini phono
jack, wired as follows:
Ring = +5V
Tip = IR Input
Sleeve = Ground
When an external remote control or infrared receiver is connected to the
wired IR input, the IR sensor on the front of the VHD is disabled.
Note
10. RS-232 CONTROL PORT
A female, 9-pin D-sub connector for interfacing with a PC or home theater
automation/control system.
11. POWER INPUT (100 to 240 VAC)
Connect the VHD Controller to power here.
12. MAIN AC FUSE
This is the main AC input fuse (5mm x 20mm, 500 mA, 250V slow-blow).
13. MAIN POWER SWITCH
Disconnects or applies power to the VHD Controller.
10
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1. IR OUTPUT INDICATOR
Lights when a button is pressed to indicate that an IR signal is being transmitted.
2. LIGHT
Press to illuminate the buttons.
3. ON / OFF
Press to turn the projector on or off.
4. ENT (Enter)
Press to select a highlighted menu item or confirm a changed setting.
On some remote control units, this button is where the RETURN/EXIT
button (item #6) appears here.
Note
5. Cursor Buttons (
,
,
,
)
Use these buttons to select items or settings, adjust settings or switch display patterns.
When no menu is present on-screen, the UP and DOWN buttons toggle through the
available aspect ratios, in this order:
UP Button = 16:9 - Standard (4:3) - Letterbox - IntelliWide - Cinema - IntelliWide 2.35
DOWN Button = IntelliWide 2.35 - Cinema - IntelliWide - Letterbox - Standard (4:3) - 16:9
IntelliWide 2.35 is available only on the Vision 85/CineWide and only on
the analog inputs (HD/RGB, SD Component, Composite and S-Video). For
more information about aspect ratios, refer to Table 4-1.
Note
Likewise, the LEFT and RIGHT buttons toggle through the different source inputs, in this
order:
LEFT Button = HDMI 2 - HDMI 1 - HD/RGB2 - HD/RGB 1 - Component SD - S-Video 2 -
S-Video 1 - Composite
RIGHT Button = Composite - S-Video 1 - S-Video 2 - Component SD - HD/RGB 1 - HD/RGB
2 - HDMI 1 - HDMI 2
The “direct select” function of the UP, DOWN, LEFT and RIGHT buttons is
available only on the analog inputs (HD/RGB, SD Component, Composite
and S-Video).
Note
6. RETURN/EXIT
Press this button to exit the current menu and return to the previous one, or to cancel an
operation.
On some remote control units, the ENT (Enter) button (item #4) is in this
location.
Note
7. MENU
Press this button to access the OSD controls.
12
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Memory Preset Buttons:
8. ISF NT (Night)
Press to recall settings for the current input from the “ISF Night” memory preset.
9. ISF DAY
Press to recall settings for the current input from the “ISF Day” memory preset.
10. CUST 2
Press to recall settings for the current input from the “Custom 2” or “White Enhance”
memory preset.
11. CUST 1
Press to recall settings for the current input from the “Custom 1” or “Black Enhance”
memory preset.
12. VIDEO (1)
Press to select Composite video input as the source or to enter the numeric character “1.”
13. S-VID 1 (2) / S-VID 2 (5) (S-Video)
Press to select an S-Video input or to enter the numeric character “2” or “5.”
14. COMP (Component) (3)
Press to select Component SD (480i/576i) video input as the source or to enter the
numeric character “3.”
15. HD 1 (4) / HD 2 (7)
Press to select a HD (RGBHV or YPbPr component) input or to enter the numeric
character “4” or “7.”
16. HDMI 1 (6) / HDMI 2 (8)
Press to select a Digital Video input or to enter the numeric character “6” or “8.”
Aspect Ratio Selection Buttons:
Use these buttons to select an aspect ratio directly or to enter numeric characters, as follows:
17. 16:9 (9)
For viewing 16:9 DVDs or HDTV programs in their native aspect ratio.
18. 4:3 (0)
Scales the input signal to fit 4:3 display mode in the center of the screen.
19. LETBOX (Letterbox)
For viewing LaserDisc movies or non-anamorphic DVDs on a 16:9 screen.
20. I-WIDE (IntelliWide)
Enlarges a 4:3 image horizontally in a NON-linear fashion to fit 16:9 full screen display.
21. CINEMA
For viewing 2.35:1 source material.
22. SVC (CineWide-equipped projectors only)
Selects the IntelliWide 2.35 aspect ratio, used for viewing 16:9 source material on a 2.35:1
screen.
Vidikron Vision 85 Owner’s Operating Manual
13
Download from Www.Somanuals.com. All Manuals Search And Download.
The Vision 85 has a built-in keypad that you can use to access the menu system for working
paragraphs that follow describe its use.
2.6
Vision 85 Built-In Keypad
T I O R A
R E T U R N E N T E R
D O W N U P
L E F T
R I G H T
M E N U
A S P E C T
A N S D T B Y O N
RETURN ENTER
DOWN
UP
LEFT
RIGHT
MENU
ASPECT
RATIO
STANDBY
ON
1
2
3
4
5
6
7
Figure 2-6. Vision 85 Built-In Keypad
1. RETURN
Press RETURN to exit the current menu or cancel an operation.
2. ENTER
Press ENTER to confirm a menu item selection.
3. DOWN / UP / LEFT / RIGHT
Use these buttons to select menu items or adjust settings.
4. MENU
Press MENU to display or hide the OSD menus for digital 1080i or 1080p sources.
5. (not used)
6. STANDBY
Press STANDBY to put the projector into standby mode.
7. ON
Press ON to turn the projector on or off.
Only trained service personnel should use the built-in keypad.
Almost all projector configuration and operational tasks can be
performed using the VHD Controller.
Note
It is only necessary to use the built-in keypad if IR signals from the remote
control cannot reach the VHD Controller, or for performing
service-related tasks such as resetting the lamp hour counter (refer to
Lamp Replacement on page 63).
14
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3Installation
3.1
Remote Control
To install batteries in the remote control:
Battery Installation
1. Remove the battery cover from the back of the remote control.
2. Insert the batteries included with the remote control. Ensure that the polarities correctly
match the
and
markings inside the battery compartment.
3. Replace the battery cover.
1. Do not mix an old battery with a new one or different types of batteries.
Note
2. If you will not use the remote control for a long time, remove the batteries
to avoid damage from battery leakage.
3-1.
Notes on Remote Control
Operation
Component SD NTSC
16:9
480i
V85
Approx.
7m/23ft
LIGHT
ON
OFF
ENT
RETURN
EXIT
MENU
MEMORY
ISF
NT
ISF
DA
CUST
1
CUST
2
Y
SOURCE SELECTION
S-VID
1
VIDEO
1
COMP
3
2
HD
1
S-VID
2
HDMI
1
4
5
6
HD
2
HDMI
2
7
8
ASPECT
4x3
LET
ANA
BOX
I-WIDE
CINEMA
SVC
Figure 3-1. Available Range of the Remote Control
Vidikron Vision 85 Owner’s Operating Manual
15
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Do not drop the remote control or expose it to moisture or high temperature.
The remote control may malfunction under a fluorescent lamp. If that occurs, move the
VHD Controller away from the fluorescent lamp.
•
Make sure that there is nothing obstructing the infrared beam between the remote
control and the IR receiver on the VHD Controller or projector.
The signal from the remote control can be reflected by walls or other
surfaces.
Note
•
•
If the effective range of the remote control decreases, or it stops working, replace the
batteries with new ones.
Ambient conditions may possibly impede the operation of the remote control. If this
happens, point the remote control at the VHD Controller or projector and repeat the
operation.
16
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
this one provide detailed instructions.
3.2
Quick Setup
Installation should be performed by a qualified custom video installation
specialist.
Note
Table 3-1. Installation Overview
For Details, Refer to
page...
Step
Procedure
Choose a location for the projector
1
2
3
4
Connect the VHD Controller to the projector
Connect signal sources to the VHD Controller
Connect external controller to RS-232 port (optional)
Connect other home theater components to 12-volt trigger
outputs (optional)
5
6
7
Apply power to the projector
For rear-screen and/or ceiling-mount installations, select the
proper picture orientation
Primary lens adjustments: projected image size (zoom),
position (shift) and focus
8
9
Install CineWide anamorphic lens (optional)
CineWide lens adjustments: position, pitch (angle), geometry
and focus
10
Projector calibration – Analog 1080i and lower-resolution
signals:
Adjust the following for Component SD input; save settings
when finished:
• Aspect ratio
• Brightness
• Contrast
11
39 through 52
• Color level
• Tint
• Input position
HD1 and HD2 inputs
12
13
Projector Calibration – Digital 1080i or 1080p signals:
Adjust the following for HDMI 1 and HDMI 2 inputs:
• Brightness
• Contrast
52 through 61
• Color level
• Tint
• Input position
Vidikron Vision 85 Owner’s Operating Manual
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Proper installation of your projector will ensure the quality of your display. Whether you are
installing a projector temporarily or permanently, you should take the following into account
to ensure your projector performs optimally.
3.3
Installation Considerations
Installation Type
Choose the installation type that best suits your needs: front or rear screen, floor mount or
➤
Table 3-2. Projector Installation Options
Advantages
Front Screen, Floor Mount Installation
• Shares floor space with audience
Considerations
• Easy to set up
• Can be moved or changed quickly
• Easy to access
Front Screen, Inverted Mount (ceiling) Installation
• Does not take up audience space
• Projector is unobtrusive
• Installation is more permanent
• Projector access is more difficult
• Projector cannot be accidentally moved
Rear Screen, Floor Mount Installation
• Projector is completely hidden
• Projector is easily accessed
• Requires separate room
• Installation cost is usually higher
• Usually good ambient light rejection
Rear Screen, Inverted Mount (ceiling) Installation
• Projector is completely hidden
• Requires separate room
• Usually good ambient light rejection
• Installation cost is usually higher
Rear Screen, Floor Mount with Mirror
• Projector is completely hidden
• Usually good ambient light rejection
• Requires less space behind screen than other
rear screen installations
• Requires separate room
• Installation cost is usually higher
Ambient Light
In general, minimize or eliminate light sources directed at the screen. Contrast ratio in your
images will be noticeably reduced if light directly strikes the screen, such as when a shaft of
light from a window or floodlight falls on the image. Images may then appear washed out
and less vibrant.
➤
18
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Throw distance is the distance measured from the front of the projector to the screen. This is
an important calculation in any projector installation as it determines whether or not you
have enough room to install your projector with a desired screen size and if your image will
be the right size for your screen.
Throw Distance
You can quickly estimate the throw distance by taking the width of the screen and
roughly how far back the projector should be positioned from the screen in order to project a
focused image large enough to fill the screen.
Estimating Throw Distance
Throw Distance (TD) = Screen Width (w) x Lens Throw Ratio
Vision 85 Throw Ratio: 1.86 to 2.45
Scr
Vision 85/CineWide Throw Ratio: 1.92 to 2.45
een width (w)
TD
Figure 3-2. Estimating Throw Distance
The Vision 85 offers a throw ratio of between 1.86 and 2.45. For example, with a 100-inch
wide screen, the Vision 85 has a throw distance range of between 186 inches (4.72 meters)
and 245 inches (6.22 meters).
The Vision 85/CineWide offers a throw ratio of between 1.92 and 2.45. For example, with
a 100-inch wide screen, the Vision 85 has a throw distance range of between 192 inches (4.88
meters) and 245 inches (6.22 meters).
Vidikron Vision 85 Owner’s Operating Manual
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Vertical and Horizontal
Proper placement of the projector relative to the screen will yield a rectangular,
perfectly-centered image that completely fills the screen.
➤
Position
Ideally, the projector should be positioned perpendicular to the screen and in such a way
Ceiling Installation
Ceiling
Height
Projection Distance
Lens Center
x
Screen Lens Center
Floor Installation
Screen
Lens Center
Height
Lens Center
x
Projection Distance
Floor
Figure 3-3. Projector Placement
Vertical Lens Shift
lens shift controls to center the image on the screen. Lens shift is generally expressed as a
➤
Screen Center
0%
50% Height
Lens Shift
(0.5 x H)
100% Height
Lens Shift
(1.0 x H)
Note: This is a general example of lens shift. Lenses vary in their shift capabilities. No particular lens or
projector is used in this example.
Figure 3-4. Vertical Lens Shift (EXAMPLE ONLY)
20
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
The Vision 85 provides up to 50% of vertical lens shift in either direction. For example,
with a 96 x 54-inch (16:9) screen, you can shift the image up to 27.00 inches (0.69 meters)
above or below the screen center.
In rear screen applications where space behind the projector is limited, a mirror may be used
be accurately set. If you are considering this type of installation, contact your dealer for
assistance.
Folded Optics
Screen
Mirror
Figure 3-5. Folded Optics
Other considerations and tips that can help improve your installation:
Other Considerations
•
•
Keep the ambient temperature constant and below 35°C (95°F). Keep the projector away
from heating and/or air conditioning vents. Changes in temperature may cause drifts in
the projector circuitry, which may affect performance.
Keep the projector away from devices that radiate electromagnetic energy such as motors
and transformers. Common sources of these include slide projectors, speakers, power
amplifiers and elevators.
Vidikron Vision 85 Owner’s Operating Manual
21
Download from Www.Somanuals.com. All Manuals Search And Download.
There are several methods for mounting the projector. Depending on your chosen
installation, one method may be more suitable than another.
3.4
Mounting the Vision 85
Floor Mounting (Upright)
In typical front and rear screen installations, the projector can be mounted to a secure and
level surface such as a table or cart. Carts are useful when moving a projector during a
presentation or from site to site. If possible, lock the wheels when it’s in position to prevent it
from being moved during a presentation.
➤
➤
Ceiling Mounting (Inverted)
For fixed installations, and for those that want the projector out of sight or have a limited
space for projector and audience, you can invert the Vision 85 and suspend it from the ceiling
using a specially-designed ceiling mount fixture.
Use only the Vidikron-approved ceiling mount kit designed for your
projector. Install the mount kit according to the instructions provided
with it.
Note
The projector can also be inverted and placed in an enclosure above and behind the viewing
area. Install four feet on the inside bottom surface of the enclosure on which the projector
can rest. A variety of materials can be used for this purpose (for example, rubber crutch tips
or turntable feet).
Adjusting the Projection
Angle
If the Vision 85 is ceiling-mounted and the screen is significantly lower than the projector,
you can tilt the projector at a slight angle by adjusting the ceiling mount.
➤
If you do this, you may need to shift the image using the OSD controls, to compensate. For
detailed instructions, refer to Using the On-Screen Menus on page 37.
22
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Proceed as follows to connect the VHD Controller to the Vision 85, your video sources,
external controller(s) – if present – and AC power.
3.5
Connections to the Vision
85 and VHD Controller
When connecting your equipment:
•
•
•
Turn off all equipment before making any connections.
Use the correct signal cables for each source.
Ensure that the cables are securely connected. Tighten the thumbscrews on connectors
that have them.
To access the connector panel, press
the door release button so it pops out.
Turn the knob clockwise or
Connector Panel Access
counter-clockwise and pull gently on it
to open the door.
The Vision 85 is designed to receive only video input signals directly from the companion
VHD Controller/Processor. Connect all signal sources to the appropriate inputs on the rear
panel of the VHD. The signal from the VHD is then output to the Vision 85 projector through
an HDMI cable.
Connecting the Projector to
the VHD Controller
You CANNOT connect signal sources directly to the Vision 85. They MUST
be routed through the VHD Controller for proper operation.
Note
Connect the HDMI and RS-232 outputs of the VHD Controller to the corresponding inputs of
T I O R A
A S P E C T
R E T U R N E N T E R
D O W N U P
L E F T
R I G H T
M E N U
A N S D
T
B Y
O N
RETURN ENTER
DOWN
UP
LEFT
RIGHT
MENU
ASPECT
RATIO
STANDBY
ON
H D M I
HDMI
T R I G G E R I R
IR
R S - 2 3 2 O U T
RS-232 OUT
A C I N
TRIGGER
AC IN 100-240V 50-60Hz
SYSTEM CONTROL INTERFACE
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Serial No
INPUTS
B/Pb
!
R/Pr
G/Y
H
V
AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
TRIGGERS
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER. NO USER-
SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE CENTER.
HD1
HD2
1
2
IR
Video roller
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
R/Pr
G/Y
B/Pb
H
V
SDI
Pb
Pr
Y
S-Video
S-Video
1
2
100-230VAC 50-60 Hz, 165 Watts Max
Made In USA
HDMI Out
HDMI
1
HDMI
2
Option
Component Video
Video
RS-232 Out
RS-232 Control
HDMI OUT
RS-232 OUT
Figure 3-6. Connecting the Projector to the VHD Controller
Vidikron Vision 85 Owner’s Operating Manual
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Source
Components to the VHD
Controller
Connect your video sources to the VHD Controller as shown and described in the sections
that follow.
➤
HDMI Connections: See Figure 3-7.
Use the HDMI inputs whenever possible. This ensures the highest video
quality because the signal is carried in the digital domain throughout the
entire signal path, from source component output into the projector.
Tip
INPUTS
R/Pr
G/Y
B/Pb
H
V
TRIGGERS
2
HD1
HD2
1
3
IR
R/Pr
G/Y
B/Pb
H
V
Pb
Pr
Y
S-Video 1
HDMI 1
HDMI 2
Component Video
Video
S-Video 2
HDMI Source
(HD-DVD/BD/DVD Player or
HD Tuner with
HDMI or DVI out)
Figure 3-7. HDMI Source Connections
24
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
INPUTS
R/Pr
G/Y
B/Pb
H
V
TRIGGERS
2
HD1
HD2
1
3
R/Pr
G/Y
B/Pb
H
V
S-Video 1
HDMI 1
HDMI 2
Pb
Pr
Y
Video
S-Video 2
Component Video
Red/Pr Green/Y Blue/Pb
Horiz
Vert
DTV or Progressive
Component (YPbPr)
Source
Figure 3-8. Digital (DTV) RGB or Component Video Connections
Vidikron Vision 85 Owner’s Operating Manual
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Analog (Computer) RGB Connections: See Figure 3-9.
INPUTS
R/Pr
G/Y
B/Pb
H
V
TRIGGERS
2
HD1
HD2
1
3
R/Pr
G/Y
B/Pb
H
V
S-Video 1
HDMI 1
HDMI 2
Pb
Pr
Component Video
Y
Video
S-Video 2
Red Green Blue Horiz Vert
Personal Computer
Figure 3-9. Analog RGB Connections
26
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Composite/S-Video/Component Video Connections: See Figure 3-10.
INPUTS
R/Pr
G/Y
B/Pb
H
V
TRIGGERS
2
HD1
HD2
1
3
R/Pr
G/Y
B/Pb
H
V
S-Video 1
HDMI 1
HDMI 2
Pb
Pr
Component Video
Y
Video
S-Video 2
Pb Pr
Y
DVD Player, VCR,
Satellite Receiver,
Laser Disc etc.
Figure 3-10. Composite, S-Video and Component Video Connections
Vidikron Vision 85 Owner’s Operating Manual
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a PC or
Automation System to the
VHD Controller
Use a standard, 9-pin RS-232 cable to connect a PC or home theater control/automation
➤
For more information about using this connection, refer to Serial Communications on
page 67.
5
4
3
1
2
TRIGGERS
2
6
9
8
7
1
3
IR
Pb
Pr
Y
S-Video 1
2 Transmit Data
3 Receive Data
5 Ground
Component Video
Video
S-Video 2 RS-232 Out
RS-232 Control
(none of the other pins are used)
to Automation/
Control System
or PC
Figure 3-11. RS-232 Control System Connection
Connecting 12-Volt Trigger
Outputs to External
Equipment
VHD Controller: If your home theater contains equipment that responds to 12-volt triggers
(such as a retractable screen or screen mask), connect them to the 12-volt trigger outputs of
➤
For more information on using the VHD Controller triggers, refer to Triggers on page 51.
TRIGGERS
1
2
3
IR
Pb
Pr
Y
S-Video 1
Component Video
Video
S-Video 2 RS-232 Out
RS-232 Control
3.5-mm
mini plug
to other,
12-volt
trigger-activated equipment
(screen, screen mask etc.)
Sleeve = Ground
Tip = +12V
Figure 3-12. 12-volt Trigger Output Connections (from VHD Controller)
28
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector: The projector is equipped with an additional 12-volt trigger output. This trigger
activates when the projector is turned on. Connect it to your retractable screen or other,
T I O R A
A S P E C T
R E T U R N E N T E R
D O W N U P
L E F T
R I G H T
M E N U
A N S D
T
B Y
O N
RETURN ENTER
DOWN
UP
LEFT
RIGHT
MENU
ASPECT
RATIO
STANDBY
ON
H D M I
HDMI
T R I G G E R I R
IR
R S - 2 3 2 O U T
A C I N 1 0 0 - 2 4 0 V 5 0 - 6 0 H z
TRIGGER
RS-232 OUT
(cylindrical,
DC power
supply-type
plug)
AC IN 100-240V 50-60Hz
to retractable screen
or other, 12-volt
trigger-activated
equipment
Sleeve = Ground
Tip = +12V
Figure 3-13. 12-volt Trigger Output Connection (from Projector)
If infrared signals from the remote control cannot reach the VHD Controller due to excessive
distance or obstructions such as walls or cabinet doors, you can connect an external IR
Connecting an External IR
Receiver to the VHD
Controller
VHD Controller Rear Panel
SYSTEM CONTROL INTERFACE
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
!
AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
TRIGGERS
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER. NO USER-
SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE CENTER.
1
2
3
IR
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
S-Video
S-Video
1
2
100-230VAC 50-60 Hz, 165 Watts Max
Made In USA
Video
RS-232 Out
RS-232 Control
Ring = +5V
Tip = IR Input
IR Receiver
Sleeve = Ground
Remote
Control
(3.5-mm
mini phono
plug)
Figure 3-14. External IR Receiver Connection
When an external IR receiver is connected to the wired IR input, the
built-in IR sensor on the VHD Controller is disabled.
Note
Vidikron Vision 85 Owner’s Operating Manual
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to AC Power
The Vision 85 system includes two (2) AC power cords (one each for the projector and VHD
Controller).
➤
Plug the female end of one power cord into the AC receptacle on the rear of the Vision 85 (AC
100V to 240V). Then, connect the other end to your AC power source. Similarly connect the
VHD Controller to a nearby AC outlet.
1. Turn on your source components.
3.6
Turning on the Power
2. Turn on the main power switch at the rear of the VHD Controller.
3. Press the ON button on the remote control – or the POWER ( ) button on the VHD
Controller front panel – to turn on the system. The vacuum fluorescent display on the
VHD Controller front panel briefly displays “Starting Display.”
4. When the projector is ready for use, the fluorescent display indicates the active source,
signal format (NTSC or PAL), input resolution and aspect ratio; for example:
Input
Current Source
Format
Resolution
Component SD NTSC
16:9
480i
V85
Aspect Ratio
By default, the Vision 85 is configured for a “floor/front” installation, in which the projector is
installed upright and in front of the screen. If it is installed behind the screen and/or mounted
on a ceiling, you must change the picture orientation. To do this:
3.7
Adjusting the Picture
Orientation
1. Select an input OTHER THAN HDMI 1 or HDMI 2 on the VHD Controller.
2. Press MENU and enter the Service Menu passcode.
3. Select Service from the Main Menu.
4. Select Display Device from the Service Menu, then select Configure.
5. Press , then choose Floor/Rear, Ceiling/Front or Ceiling/Rear, to match the installation
method.
You must enter a passcode to access the Service menu.
Note
30
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3.8
Primary Lens Adjustments
To focus the projected image, gently rotate the lens
by hand.
Focus and Zoom
Zoom
in
To enlarge the picture (zoom in), move the zoom tab
toward the Vidikron logo on the front of the projector.
To make the picture smaller (zoom out), move the tab
in the other direction.
Zoom
out
Focus
To change the projected image position, use a 9/64” hex driver to shift the lens in the desired
tool will automatically center on top of the adjustment nut when inserted into the access
hole.)
Vertical Lens Shift
9/64” Hex Wrench
Figure 3-15. Vertical and Horizontal Lens Shift Adjustments
Vidikron Vision 85 Owner’s Operating Manual
31
Download from Www.Somanuals.com. All Manuals Search And Download.
If you are installing a CineWide-equipped projector, proceed as follows to install and adjust
the anamorphic lens.
3.9
Installing and Adjusting
the CineWide Anamorphic
Lens
It is extremely important that the primary lens is properly adjusted
Note
before you install the anamorphic lens. Ensure that the image from
the primary lens is perfectly centered on the screen.
The standard Vision 85/CineWide uses a prismatic-style anamorphic lens. This type of lens
compresses the height of the image (as opposed to stretching the width) to achieve a 2.35:1
aspect ratio with a 1.78:1 display device.
3-16. Some components shipped with your projector may differ slightly from what is shown
in these instructions.
If any items are missing or damaged, please contact your Vidikron dealer or Vidikron
Customer Service at (888) 4VIDIKRON.
1
Anamorphic Lens
6 Pitch/Y-Adjustment
Screw, Phillips
Pan Head, 4-40 x 3/8” (2x)
and Fender Washer (2x)
2 Base Plate
5 Vertical Mounting
3 Screw, Phillips
Bracket (2x)
M6x16mm (4x) and
1/4” Flat Washer (4x)
(not shown; secures Base Plate
to bottom of projector)
4 Yaw/Z-Adjustment
Lever (2x) and
Fiber Washer (2x)
Figure 3-16. Vision 85 Anamorphic Lens Mounting Assembly - Exploded View
1. Use the Pitch Adjustment Screws (item #3) and Washers (item #6) to attach the Mounting
Brackets (item #2) to the Anamorphic Lens (item #1).
2. Use the four Y-Adjustment Screws (item #5) and Washers (item #4) to attach the
Anamorphic Lens assembly and Spacers (item #7) to the front of the projector. (Do not
fully tighten the screws yet.)
32
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
To avoid clipping the corners of the image, position the anamorphic lens
as close as possible to the primary lens.
Tip
Adjusting the Lens Height (Y):
1. Project a white field on the screen.
2. Ensure that the four Height (Y) Adjustment Screws are loose enough to allow vertical
movement of the lens assembly.
3. Slowly move the anamorphic lens into place so that there are no shadows on the top or
bottom of the screen:
Too Low
Correct position
Too High
4. When the height is properly set, tighten the Height Adjustment Screws to secure the
lens in place.
Adjusting the Pitch (Angle): Next, angle the lens to even out any top-to-bottom pincushion
distortion. To do this, loosen the Pitch Adjustment Screws on either side of the lens to allow it
to pivot freely. Then, adjust the anamorphic lens angle so that the projected image is
rectangular:
Vidikron Vision 85 Owner’s Operating Manual
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Correct Lens Angle
Incorrect Lens Angle
The anamorphic lens will almost always be angled with respect to the projector; this is
normal. Once the proper lens angle has been set, firmly tighten the Pitch Adjustment Screws
to secure the lens in place.
There may be some pincushion distortion even after the lens is properly
Note
adjusted, especially at shorter throw distances. If this is the case, Vidikron
recommends that you slightly over-scan the image into the screen frame
area to mask the distortion.
Adjusting the Yaw: Loosen the Yaw/Z-Adjustment Levers to allow the lens to pivot freely
from side to side. Then, angle the lens to even out any left-right pincushion distortion:
Anamorphic Lens (Top View)
Correct Position
Wrong Position
Once the proper lens angle has been set, firmly tighten the Yaw/Z-Adjustment Levers to
secure the lens in place.
34
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4Operation
Press the MENU button on either the remote control or the VHD Controller front panel to
display the Main Menu.
4.1
Using the On-Screen
Menus
To select a menu item, use the and buttons on either the remote control or the VHD
Controller front panel to highlight it. Press ENTER to confirm your selection.
The Vision 85 OSD menus are arranged hierarchically; exactly how they are arranged
depends on the input signal resolution. For 1080i digital or 1080p signals, the menu
When the input signal resolution is 1080i analog (via the HD1 or HD2 input) or lower, the
characteristics, some menu options may not be available.
4.2
On-Screen Menus for 1080i
(Analog) and
Lower-Resolution Signals
Vidikron Vision 85 Owner’s Operating Manual
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Composite
S Video 1
Gain
Offset
Gamma
Iris
S Video 2
ISF Night - Display Color
Component SD
HD/RGB 1
HD/RGB 2
HDMI 1
Input Source
Aspect Ratio
Color Temp
Lamp Power
(0 = Low; 1 = High)
Brightness
Contrast
Color
HDMI 2
16:9
ISF Night - Input Image
ISF Night - Input Color
4:3
Tint
Letterbox
Sharpness
Gain
IntelliWide
Cinema
Offset
Note: IntelliWide 2.35 is available
only on the Vision 85/CineWide
and only on the analog inputs
(HD/RGB, Component SD,
IntelliWide 2.35
Brightness
Contrast
Chroma Delay
Phase
Noise Filter
Gain
Color
Picture
Composite and S-Video).
Tint
Offset
Sharpness
Left/Right
Up/Down
Gamma
Iris
ISF Day - Display Color
ISF Day - Input Image
Color Temp
Lamp Power
Brightness
Contrast
Color
Width
Input Position
ISF Presets
Height
Calibration
Overscan
Recall ISF Night
Recall ISF Day
Recall/Save Custom 1
Recall/Save Custom 2
Reset Custom 1 & 2 to Factory Default
Serial Number
Hardware
Tint
Sharpness
Gain
Offset
ISF Day - Input Color
Save ISF Settings
Output Shift
Chroma Delay
Phase
Information
(read-only)
Firmware
Noise Filter
Back / Confirm
Left/Right
Up/Down
Width
Date
Height
Save
Owner Name
ISF Calibrated
ISF Other
Test Video
Grey Bars 1
Grey Bars 2
Splash Configure
OSD Position
Color Bars 1
Vidikron/ISF Logo Splash
Screen Timers
(2 ... 60 sec.)
Color Bars 2
Input Names
Rename, Restore or Save
Primary
Remote Control
Analog Out Mode
Secondary
RGB--, RGB++ or RGBS
Orientation
Overscan
Fan Mode
Display Device
Configure
(0 = Normal; 1 = High Altitude)
Height
(0 ... 100)
Service
Lamp Hours
HD/RGB 1
Auto, RGB or YUV
HD/RGB 2
HD Format
Triggers
ADC Bandwidth
YPbPr Input Resolution
1 / 2 / 3 / Save
Language
Auto, 75 MHz, 150 MHz or 300 MHz
Auto, 480i/p, 576i/p, 720p or 1080i
English, French, German or Spanish
Menu Mode
Miscellaneous
Timeout
Side Bar Color
Film Mode (SD src. only)
System Reset
Restore Saved Settings
Figure 4-1. VHD Controller OSD Menu Structure for Vision 85 (1080i Analog and Lower-Resolution Sources)
36
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
The Main Menu is the starting point for accessing all projector functions.
Main Menu
(The Calibration and Service menus are hidden and not accessible until you enter a
passcode.)
Vidikron 85
Input Source
Aspect Ratio
Picture
Input Position
ISF Presets
Information
Calibration
Service
From the Main Menu, select Input Source to choose a video signal source.
Input Source
The active source is indicated by an arrow (>) to its left; in the example at right, Composite is
the active source.
Input Source
Composite
>
S Video 1
S Video 2
Component SD
HD/RGB 1
HD/RGB 2
HDMI 1
HDMI 2
To change the aspect ratio (size and shape) of the projected image, select Aspect Ratio from
the Main Menu and press ENTER. Select the appropriate aspect ratio for your screen size and
Aspect Ratio
Aspect Ratio
16:9
4:3
7
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
The currently-selected aspect ratio is indicated by a “7” to its left; in the example at right,
16:9 is selected.
Letterbox
When you change the aspect ratio, save the change to a preset
IntelliWide
Cinema
Note
afterwards. Otherwise, the change will be lost when a different input is
selected. (The aspect ratio is saved for each input and resolution
separately.) For information about saving settings, refer to ISF Presets
IntelliWide 2.35
Vidikron Vision 85 Owner’s Operating Manual
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 4-1. Aspect Ratio Settings
Aspect Ratio
Description
Select 16:9 to view 16:9 DVDs and HDTV
16:9
programs in their native aspect ratio.
16:9 Image on
16:9 Screen (Display)
4:3 images are stretched horizontally to fit
a 16:9 screen.
4:3 Image, stretched to fill
16:9 Screen (Display)
4:3
4:3 scales the input signal to fit in the
center of the 16:9 screen. 4:3 is the aspect
ratio used by computer monitors,
standard television programming and
most VHS video cassettes.
4:3 Image on
16:9 Screen (Display)
Letterbox
Letterbox mode scales (zooms in on) a 4:3
image linearly (by the same amount on all
sides) to fill a 16:9 display.
Letterbox is best suited for viewing
LaserDisc movies or non-anamorphic
DVDs on a 16:9 screen.
4:3 Image on
16:9 Display
(Letterbox aspect ratio)
IntelliWide
IntelliWide scales a 4:3 image
NON-linearly (more on the sides than in
the center) to fit a 16:9 screen.
4:3 Image on
16:9 Screen (Display)
4:3 Image on
16:9 Screen
with IntelliWide
On a 2.35:1 screen, the image is centered
between black bars on either side.
4:3 Image on
2.35:1 Screen
with IntelliWide
38
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 4-1. Aspect Ratio Settings (continued)
Aspect Ratio
Description
Cinema
Select Cinema to view 2.35 source
material in its native aspect ratio.
With a 16:9 screen and a non-CineWide
projector (no anamorphic lens), the upper
and lower portions of the screen are
masked, but the geometry of the active
image area is unchanged.
2.35:1 Image on
16:9 Screen
(Cinema aspect ratio / no CineWide)
With a 2.35:1 screen and a
CineWide-equipped projector, the VHD
Controller scales the 2.35:1 image so that
the active image area fills the 16:9 chip
surface, eliminating the black bars. The
secondary, anamorphic lens then restores
the proper geometry to the 2.35:1 image.
2.35:1 Image on
2.35:1 Screen
(Cinema aspect ratio / CineWide)
IntelliWide 2.35
A 16:9 image is scaled NON-linearly (more
on the sides than in the center) to fit a
2.35:1 screen. IntelliWide 2.35 is available
only on the Vision 85/CineWide and only
on the analog inputs (HD/RGB, SD
2.35:1 Screen
16:9 Image on
Component, Composite and S-Video).
16:9 Image on
2.35:1 Screen with
Virtual Cinema
Use the controls in the Picture Menu to calibrate your Vision 85 for optimum picture quality.
Picture
The Vision 85 has been designed to incorporate setup and calibration standards established
by the Imaging Science Foundation (ISF). The ISF has developed carefully crafted,
industry-recognized standards for optimal video performance and has implemented a
training program for technicians and installers to use these standards to obtain optimal
picture quality from Vidikron video display devices. Accordingly, Vidikron recommends that
setup and calibration be performed by an ISF certified installation technician.
Picture
Brightness
Contrast
Color
Tint
Sharpness
All signal types require separate processing. Therefore, you need to calibrate each input
separately.
When you change a picture quality setting, save the change to a preset
Note
afterwards. Otherwise, the change will be lost when a different input is
selected. (Picture quality settings are saved for each input and resolution
separately.) For information about saving settings, refer to ISF Presets
Vidikron Vision 85 Owner’s Operating Manual
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Although it may be possible to obtain satisfactory picture quality using the naked eye and
regular program material, Vidikron recommends using the following calibration tools for
best results:
•
External test pattern source -- Ovation Multimedia, Digital Video Essentials or AVIA test
DVD or equivalent.
•
A blue filter (provided with many test DVDs), for color level and tint adjustments.
Connect your test pattern source to the input that you are calibrating and proceed as follows.
Perform the adjustments in the order listed here.
Brightness: On your external test pattern source, select a PLUGE pattern. (PLUGE is an
pattern.
Below Black
Above Black
Figure 4-2. Typical PLUGE Pattern for Adjusting Brightness
PLUGE patterns vary but generally consist of some combination of black, white and gray
areas against a black background. The example above includes two vertical bars and four
shaded boxes.
Select Brightness from the Picture menu and press ENTER. Adjust the brightness so that:
•
•
•
•
•
The darkest black bars disappear into the background.
The dark gray areas are barely visible.
The lighter gray areas are clearly visible.
The white areas are a comfortable level of true white.
The image contains only black, gray and white (no color).
40
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Contrast: On your external test pattern source, select a stepped, gray-bar pattern like the
Figure 4-3. Typical Gray Bar Pattern for Adjusting Contrast
Select Contrast and press ENTER. Adjust the contrast to a point just below which the white
rectangle starts to increase in size.
Brightness and contrast controls are interactive. A change to one may
require a subtle change to the other in order to achieve the optimum
setting.
Note
Color Saturation: On your external test pattern source, select a color bar pattern like the one
Figure 4-4. Typical Color Bar Pattern for Adjusting Color Saturation and Tint
Vidikron Vision 85 Owner’s Operating Manual
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Select Color and press ENTER. While looking at the color bar pattern through a blue filter,
adjust the color saturation level until the outermost (gray and blue) color bars appear to be a
single shade of blue:
Tint: Tint or “hue” is essentially the ratio of red to green in the color portion of the image.
When tint is decreased, the image appears redder; when it is increased the image appears
greener. To set the tint, select Tint and press ENTER. While looking at the color bar pattern
through a blue filter, adjust the tint level until the cyan and magenta color bars (on either
side of the green bar) appear to be a single shade of blue.
Like the brightness and contrast controls, the color and tint controls are
interactive. A change to one may require a subtle change to the other in
order to achieve the optimum setting.
Note
42
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Sharpness: “Sharpness” is the amount of high-frequency detail in the image. To adjust
sharpness, select Sharpness from the Picture menu and press ENTER. On your external test
for white edges around the transitions from black to gray and differently-sized lines in the
“sweep” patterns at the top and bottom. Lower the sharpness setting to eliminate them.
Figure 4-5. Typical Test Pattern for Adjusting Sharpness
Use the controls in the Input Position Menu to fine-tune the aspect ratio and image position
for the current source.
Input Position
Input Position
Left/Right
Up/Down
Width
When you change an input position setting, save the change to a preset
Note
afterwards. Otherwise, the change will be lost when a different input is
selected. (The input position settings are saved for each input and
resolution separately.) For information about saving settings, refer to ISF
Height
Overscan
Left/Right: Select Left/Right from the Input Position menu to shift the projected image
horizontally. Use the right or up cursor button to shift the image to the right; use the left or
down button to shift it to the left.
Up/Down: Select Up/Down from the Input Position menu to shift the projected image
vertically. Use the right or up cursor button to shift the image upward; use the left or down
button to shift it downward.
Width: Select Width from the Input Position menu to change the projected image width. Use
the right or up cursor button to increase the width; use the left or down button to decrease it.
Height: Select Height from the Input Position menu to change the projected image height.
Use the right or up cursor button to increase the height; use the left or down button to
decrease it.
Overscan: Image Overscan pushes the outside edge of the active picture area of the video
signal out beyond the edge of the display area.
Vidikron Vision 85 Owner’s Operating Manual
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Some television programs are produced based on the assumption that older television sets
may not display the outer edges of the broadcast picture area. Overscan effectively trims
away these inactive, outer edges and enlarges the remaining portion of the image to fill the
display area.
Select from 1% to 10% of Overscan, as desired.
For HDTV, DVDs and other video sources, Overscan is generally not necessary or desirable.
ISF Presets
For each input, the Vision 85 lets you save image quality settings as presets that you can
recall at a later time. You can create up to four presets per input and resolution. Use the ISF
Presets menu to recall saved image presets, or to save image settings in the “Custom 1” or
“Custom 2” memory location. The currently-selected preset is indicated by a “7” to its left; in
the example shown here, ISF Night is selected.
➤
ISF Presets
ISF Night
7
ꢀ
ꢀ
ꢀ
ISF Day
You should save changes to any of the following settings to a preset; otherwise they will be
lost when a new input source or resolution is selected:
Custom 1 Save
Custom 2 Save
•
•
•
Aspect ratio
Factory Default
Picture quality settings (brightness, contrast, color saturation, tint and sharpness)
Input position (image position, width, height and overscan percentage)
To reset the Custom 1 and Custom 2 image presets to their factory defaults, select Factory
Default and press ENTER.
Information
Select Information from the Main Menu to see information that uniquely identifies your
projector: its serial number, the installed hardware and firmware versions and the firmware
version build date. Should you ever need to contact Vidikron Technical Support, this
information will help them answer your questions or resolve product performance issues.
➤
Information
Serial Num
Hardware
Firmware
Date
0
0100.0331
Dec 11 2006
44
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Use the Calibration menu to perform advanced picture quality adjustments. This menu
Calibration
should be used by ISF-certified technicians only.
Calibration
ISF Night
You must enter a passcode to access the Calibration menu.
Display Color
Input Image
Input Color
Note
ISF Day
To recall the ISF Night or ISF Day settings, do one of the following:
Display Color
Input Image
Input Color
•
•
•
Select “ISF Night” or “ISF Day” from the ISF Presets menu (see above);
Press ISF NT or ISF DAY on the remote control; or
From this menu, choose Display Color, Input Image or Input Color for the preset you want
to recall.
Save ISF Settings
Output Shift
Splash Configure
OSD Position
ISF Night - Display Color: Use the Display Color settings to change the characteristics of the
output signal. These settings are global (independent of any particular input).
•
Gain: Use the Gain controls to correct color imbalances in the bright areas of the image. A
good way to do this is to use a test pattern consisting mostly of solid white areas, such as
an 80 IRE “window” pattern. If the white areas contain traces of red, green or blue,
decrease the Gain for that color.
•
Gamma/Offset: Use the Gamma and Offset controls in the White Balance sub-menu to
correct color imbalances in the dark areas of the image.
A good way to do this is to use a test pattern consisting mostly of dark gray areas, such as
a 30 IRE “window” pattern. If the gray areas contain traces of red, green or blue, decrease
the Gamma or Offset for that color.
Adjust Gamma before Offset. Gamma provides coarse adjustment of
low-lights; Offset provides finer adjustment.
Tip
•
Iris: Select Iris from the Display Color Menu to increase or decrease the aperture or iris size
(the physical opening through the lens; similar to an “f-stop” on a camera). Doing so
allows you to optimize brightness and contrast according to the amount of ambient light
in the viewing area.
Use a lower setting (0 or 1) for rooms with lots of ambient light. Use the higher setting (2)
for more “theater-like” viewing conditions (little or no ambient light).
•
•
Color Temp: Select Color Temp from the Display Color menu to adjust the color
temperature. The default setting is appropriate for most situations. Higher settings
produce a “bluer” picture.
level. You can choose to run the lamp as bright as possible (“1”) or you can choose the
lower setting (“0”). Generally, lower lamp output can prolong the life of the lamp, but
decreases brightness.
Vidikron Vision 85 Owner’s Operating Manual
45
Download from Www.Somanuals.com. All Manuals Search And Download.
but are accessible only by entering the Calibration menu passcode. This makes it possible to
restore the picture quality settings to what they were when the projector was installed,
simply by recalling the “ISF Night” preset.
ISF Night - Input Color: The Input Color controls are similar to those in the Display Color
menu (see above), but can be set independently for each input.
•
•
Chroma Delay: use the Chroma Delay control to correct a mis-aligned image from a
Composite, S-Video or Component video source. Chroma delay in an image causes color
shifts to occur to the left of the vertical edge transitions, producing artificial shadows or a
“halo” effect. If necessary, adjust this setting to eliminate them.
•
Phase: Adjust the phase if the image (usually from an RGB source) shows shimmer or
“noise.” Pixel phase adjusts the phase of the pixel sampling clock relative to the incoming
signal. The effect of this control is similar to that of a tracking control on a VCR.
For best results, use a good test pattern such as a smooth gray consisting of a clear pattern
of black and white pixels, or a similar “half on, half off” graphic image. (You may notice
that you can stabilize the image at more than one point. Use either setting in this case.)
•
Noise Filter: Select Noise Filter from the Input Color menu to filter a noisy Composite,
S-Video or Component source signal. Adjust as desired, keeping in mind that reducing
noise (which reduces high frequencies) may also soften the image.
Save ISF Settings: Whenever you make a change to the ISF settings, you should always save
it. Select Save ISF Settings from the ISF Calibration menu to do this. In the event you ever
menu, except that they change the characteristics of the output signal (so the change is
visible no matter which input is selected). You can set these controls independently for each
aspect ratio.
To save the Output Shift settings for the current aspect ratio so that they can be restored
press ENTER.
Splash Configure: Use the Splash Configure menu to customize the appearance of the
start-up message that appears on the vacuum fluorescent display upon power-up.
•
name, your name, the phrase “ISF Calibrated” and/or any other string, up to 20 characters
in length.
Use the up or down cursor button to select a character. Use the right and left cursor
buttons to change the cursor position. Press MENU when you have finished entering text.
Then, check the “Splash Enable” box to have the Vision 85 display the information you
enter here when it is turned on.
46
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
•
welcome screen with the Vidikron logo followed by one with the ISF logo. Select Splash
appear. The range is from 2 to 60 seconds, in one-second increments.
Use the up or down cursor button to select a timer value to adjust. Use the right or left
cursor button to change the timer value. Press MENU when you have finished configuring
both timers.
OSD Position: Select OSD Position, press ENTER and use the arrow buttons to change the
size and position of the OSD controls.
Use the Service menu to access advanced projector configuration settings. This menu
should be used by ISF-certified technicians only.
Service
Test Video
Input Names
You must enter a passcode to access the Service menu.
Note
Remote Control
Analog Out Mode
Display Device
HD Format
Test Video: Select Test Video from the Service Menu to access the internal test patterns on
the Vision 85. Four patterns are available, consisting of white/gray or colored bars.
Triggers
Press MENU to exit test pattern mode.
Miscellaneous
System Reset
Restore Saved Settings
Input Names: You can give each VHD Controller input a descriptive name. For example, you
may want to change the default input name to the type of source component connected to
it: “VCR,” “DVD,” “Laptop” et cetera. Composite, S-Video and Component SD input names can
be up to 12 characters long; the others can be up to eight characters long.
Input Names
Restore
Composite
S Video 1
S Video 2
Component SD
HD/RGB 1
HD/RGB 2
HDMI 1
Composite
S Video 1
S Video 2
Component SD
HD/RGB 1
HD/RGB 2
HDMI 1
To edit an input name, select Input Names from the Service menu. Press or to select an
input and press ENTER. Use the or buttons to change a character; press or to
select a character to change. When you have finished editing the input name, press MENU.
To restore the default input name, press repeatedly to highlight that input name in the
“Restore” column. Then, press ENTER.
HDMI 2
HDMI 2
To save input names so that they can be restored after a System Reset (described on
Save
The button takes you from top to bottom in the left column, then from
top to bottom in the right column. To highlight “Save,” scroll through
both columns.
Note
Vidikron Vision 85 Owner’s Operating Manual
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control: The Remote Control menu shows you the primary and secondary infrared
(IR) codes to which the Vision 85 will respond. By default, both are set to 17. You can change
these codes if either:
•
Another device in the theater (a DVD player, for example) is responding to commands
from the Vision 85/VHD remote control (Figure 2-5) in ways that are unpredictable or
undesirable.
•
You have multiple Vision 85 projectors and want to control them independently, as
opposed to broadcasting commands from a single remote to all of them. In this scenario,
you can use multiple remotes programmed to use different IR codes. Or, you can use a
single remote and change the IR code as needed to address a specific projector.
Use the VHD Controller front-panel keypad to change the projector IR
code. Then, change the code sent by the remote to match as described
below.
Tip
Do not change the “Type” setting in this menu.
Note
When you change a remote code on the Vision 85, you must re-program the Vision 85/VHD
remote control to send that same code. To do this:
1. Using a straightened paper clip or similar object, press and hold the
CODE button on the remote control for approximately three
seconds, or until the LED on the remote lights solid red.
CODE
– OR –
NT
If your remote control unit does not have a CODE button, press and
hold the LIGHT button on the remote control for approximately
three seconds, or until the LED on the remote lights solid red.
2. Enter a new two-digit code between 00 and 31 inclusive. Use the
16:9 button for “9” and the 4:3 button for “0.” Include a leading
zero for single-digit codes; for example, enter 9 as “09.”
3. The LED turns off to confirm the code change. If you enter an invalid code, the LED
flashes for three or four seconds. Try again, entering a valid code.
48
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
orientation, adjust the amount of overscan and access other projector-specific functions.
•
•
installation (Floor Front, Floor Rear, Ceiling Front or Ceiling Rear).
•
•
Mode control to prevent it from overheating. Set it to High Altitude (“1”) to run the fan
at high speed; set it to Normal (“0”) to run the fan at normal speed.
•
•
height in small increments. Higher values compress the height. This setting affects all
sources.
Use this control to fine-tune the image geometry on a Vision
85/CineWide. (It should not be necessary to change this setting on a
Note
standard Vision 85.)
HD Format: If the characteristics of the incoming signal on the HD1 or HD2 inputs are
known, select HD Format from the Service menu and set them as described below. Doing so
can reduce the time it takes the VHD Controller to switch from HD to 480i signals or vice
versa.
HD Format
HD/RGB 1
HD/RGB 2
Auto
Auto
This is generally not necessary unless the VHD Controller – for whatever reason – has
difficulty determining the color space (RGB or YUV), bandwidth or resolution of the incoming
HD signal. In most situations, the Auto settings work well.
ADC Bandwidth
Auto
YPbPr Input Resolution
•
•
•
HD/RGB 1 and HD/RGB 2 (Color Space): Select Auto, RGB or YUV.
ADC Bandwidth: Select Auto, 75 MHz, 150 MHz or 300 MHz.
YPbPr Input Resolution: Select Auto or specify the input resolution, if known: 480i, 480p,
576i, 576p, 720p or 1080i.
Triggers: Select Triggers from the Service menu to configure the 12-volt trigger outputs. You
can assign one or more trigger outputs to each aspect ratio. Those triggers are then activated
by selecting that aspect ratio.
To save the trigger settings so that they can be restored after a System Reset (described
below), press repeatedly to highlight “Save.” Then, press ENTER.
Vidikron Vision 85 Owner’s Operating Manual
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Miscellaneous: Select Miscellaneous from the Service menu to set the following options:
•
Language: Select Language from the Miscellaneous menu and press the up- or
down-arrows to select the OSD Language. (Currently, only English is supported.)
•
Menu Mode: This is the manner in which the OSD menus appear and disappear when you
press MENU. Choose one of the following:
0 = No transition; menus abruptly appear and disappear.
1 = Menus fade in and out.
2 = “Checkerboard” dissolve; menus appear and disappear in sections.
3 = “Window shade” effect; menus are drawn on a diagonal from top left to bottom right,
and retract in the opposite direction.
•
•
Timeout - Short/Long: These settings control how long the OSD menus stay on screen.
Select a time-out period of from 2 to 60 seconds.
Side Bar Color: This controls the color of the inactive image area. The range is from -100
(black) to 100 (white).
The inactive image area is on either side of the active image area when using the 4:3
aspect ratio (or the entire screen when no incoming video signal is present).
•
Film Mode: Enable Film Mode to smooth out moving images from interlaced,
standard-definition (SD) sources. In most cases, the Vision 85 detects the proper
“pull-down” rate and vertical frequency. However, if your source is jittery and/or tearing
you may wish to enable Film Mode to ensure stable processing for that source.
System Reset: To reset ALL controller settings (including image settings) back to their
factory defaults, choose System Reset from the Service menu.
A confirmation message appears, reminding you to save your settings before you perform
the reset, so that you can restore them afterwards. If you have done this, select Confirm to
continue with the reset. Otherwise, click Back to cancel.
This action is not undoable. Proceed with caution! Before you perform a
Caution
Restore Saved Settings: Following a System Reset, select Restore Saved Settings to apply all
previously-saved settings to the projector and VHD Controller.
50
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
After you have finished calibrating the projector to optimize the display of 1080i analog and
lower-resolution sources, do likewise for 1080i digital and 1080p sources (connected to the
HDMI 1 or HDMI 2 inputs on the VHD Controller).
4.3
On-Screen Menus for 1080i
(Digital) or 1080p Signals
When the projector receives a 1080i digital and 1080p signal, it displays the menus shown in
Standard, Black Enhance,
White Enhance, ISF Day,
ISF Night or Custom
Frequency
Phase
Picture Memory
H-Shift
Contrast
Brightness
Color
(N/A)
-90, -89, ... 0 ... +89, +90
V-Shift
HD/RGB Adj.
Default
Special Mode
-30, -29, -28 ... 0 ... +28, +29,
+30
Tint
Signal Info
(read-only)
Format (480i ... 1080p), H/V
Sharpness
Frequency
Picture Adjust
5500, 6500, 7500, 8500, 9300
or 10500
Auto Setup
Image Shift
(N/A)
Color Temp.
-30, -29, -28 ... 0 ... +28, +29,
+30
Standard, Black Enhance,
White Enhance, ISF Day,
ISF Night or Custom
White Balance
(available only with certain
1080i signals)
Subtitle
High Brightness, Theater or
CRT Emulation
Overscan
Default
0, 1%, 2% ... 10%
Yes or No
VAC: Iris
Lamp Power
220W (Hi) or 180W (Low)
Hue
Adjust White Level
Adjust Black Level
LED
(N/A)
Saturation
Intensity
Default
Red
On or Off
Hours in use / percentage of
life remaining
Lamp Hours (read-only)
OSD
On or Off
ICC Adjust
Yellow
Auto, RGB, YCbCr4:4:4 or
YCbCr4:2:2
Options
Signal Type
Green
Cyan
Color Space
Auto, ITU601 or ITU709
Auto, 0 IRE or 7 IRE
Blue
HDMI Black Level
Background
Picture Adjust
(Advanced)
Magenta
Default
On/Off
Vidikron Logo, Blue or Black
RS-232C Port (On or Off)
Brilliant Color™
SD Advanced Mode
Film Mode
Power Save
Auto Power Off
(On or Off)
(N/A)
Baud Rate
Fan Mode
9600, 38400 or 115200 bps
Normal or High Altitude
Video NR
Floor Front, Ceiling Front,
Floor Rear or Ceiling Rear
MNR
Orientation
Off, 1, 2 or 3
Yes or No
Sharpness Enhancement
Automatic Contrast
Default
Factory Default
English
All Reset or Return
Deutsch
Español
Standard, Black Enhance,
White Enhance, ISF Day,
ISF Night or Custom
Language
Mem. Select
Français
Red Gamma
Green Gamma
Blue Gamma
Red Gain
Italiano
White Balance
-30, -29, -28 ... 0 ... +28, +29,
+30
Green Gain
Blue Gain
Red Offset
Green Offset
Blue Offset
Default
Yes/No
Figure 4-6. OSD Menu Structure for Vision 85 (1080i Digital or 1080p Sources)
Vidikron Vision 85 Owner’s Operating Manual
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Menu
Press MENU on either the remote control or built-in keypad (on the projector rear panel) to
calibrating the Vision 85 to optimize the display of digital 1080i and 1080p sources.
➤
White Balance
HD/RGB Adj.
Options
Language
Picture Adj.
Picture Memory
1
Contrast
Brightness
Color
0
0
0
Tint
Sharpness
0
0
7500
CLR Temp.
White Balance
RVR :Iris
1
1
Lamp Power
Hi
Advanced
Default
Figure 4-7. Vision 85 Main Menu (1080i Digital or 1080p Sources Only)
To use the on-screen menus:
1. Press or to select a sub-menu.
2. Press or to select a sub-menu item.
a
b
c
Press ENTER or
.
Press or to select a value from the list.
Press ENTER again to confirm your selection.
Press to return to the menu.
d
– OR –
For items that are represented by numeric values, such as Contrast:
Press or to adjust the value.
a
b
Press or to select another menu item.
– OR –
a
b
c
Press ENTER to hide the “parent” menu and display only the slidebar for that item.
Press or to adjust the value.
-
5
Contrast
+
Press or to select another item to adjust or ENTER to return to the menu.
press repeatedly until no menu item is highlighted. Then, press or
.
5. Press MENU to hide the OSD menus.
52
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
The Vision 85 OSD language is initially set to English, but can also display the menus in
German (Deutsch), Spanish (Español), French (Français) or Italian (Italiano). To change the
OSD language:
Language
1. Press MENU.
English
Deutsch
Español
Français
2. Press or to select Language from the Main Menu.
3. Press up- or down-arrow button ( or ) to highlight the desired language and press
ENTER. The change takes effect immediately.
Italiano
To perform basic picture quality adjustments, select Picture Adjust from the Main Menu and
proceed as follows:
Picture Adj.
recall at a later time. For digital 1080i and 1080p sources, you can create up to six presets.
Picture Memory
1
your selection, press ENTER.
Contrast
Brightness
Color
0
0
0
Tint
Sharpness
CLR Temp.
0
0
7500
Tint and Sharpness are all set to zero (0) by default. These provide convenient starting points
for calibrating the projector to suit different viewing environments. Any picture quality
adjustments you make here are stored in the currently-selected preset.
White Balance
VAC :Iris
1
1
Table 4-2. Default Picture Memory Settings for Digital 1080i and 1080p
Sources
Lamp Power
Hi
Advanced
Default
Default Settings for Selected Picture Memory
Picture
Memory
Setting
Description
Standard
Provides good picture
7500 High
Brightness
Hi
(220W)
Off
Off
–
or Custom quality under the widest
variety of viewing
conditions.
Black
Enhance
Similar to “Standard” mode, 7500 CRT
Hi
(220W)
Off
1
1
CUST
1
but with enhanced black
levels.
Emulation
White
Enhance
Similar to “Standard” mode, 7500 High
Hi
(220W)
Off
Off
CUST
2
but with enhanced white
levels.
Brightness
ISF Day
For viewing images with the 6500 Theater
brightness slightly
Low
(180W)
Off
ISF
DAY
decreased in a darkened
room.
Vidikron Vision 85 Owner’s Operating Manual
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 4-2. Default Picture Memory Settings for Digital 1080i and 1080p Sources
(continued)
Default Settings for Selected Picture Memory
Picture
Memory
Setting
Description
ISF Night
For viewing images with the 6500 CRT
Low
Off
Off
ISF
brightness slightly
increased in a darkened
room.
Emulation
(180W)
NIGHT
menu. (Color temperature defines the “color of gray.”) Press or to select 5500, 6500,
7500, 8500, 9300 or 10500. In most cases, 6500 or 7500 will produce the most realistic colors.
Higher settings produce a “bluer” picture; lower ones cause the image to appear more red.
balance preset (or “gamma curve”) to store in the currently-selected picture memory. For
or iris size (the physical opening through the lens; similar to an “f-stop” on a camera). Doing
so allows you to optimize brightness and contrast according to the amount of ambient light
in the viewing area.
Select High Brightness or Theater for rooms with lots of ambient light. Select CRT Emulation
for more “theater-like” viewing conditions (little or no ambient light).
level. You can choose to run the lamp as bright as possible (220W; this is the default setting)
or you can choose the lower setting (180W). Generally, lower lamp output can prolong the
life of the lamp, but decreases brightness.
54
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
This sub-menu presents the following options:
Picture Adjust (Advanced)
displayed color space. The adjustments you make here are stored in the currently-selected
ICC Adjust
BrilliantColor TM
SD Advanced Mode
Film Mode
Video NR
MNR
For each of the six primary colors – red, yellow, green, cyan, blue and magenta – you can
adjust the following:
Sharpness Enhancement
Automatic Contrast
Default
ICC Adjust
ICC- Hue
•
Hue: These slidebars adjust the red/green color hue for true color reproduction of video
signals. For best results, adjust the hue while displaying an external color bar test pattern
ICC - Saturation
ICC - Intensity
Default
Red
0
0
0
0
0
0
R
Y
G
C
B
M
R
Y
G
C
B
Changing the hue of a primary color affects the gamut (range) of possible colors. For
example, changing the value for red moves the color closer to either yellow or magenta,
which in turn affects all displayed colors having a red component.
Yellow
Green
Cyan
Blue
Magenta
M
Table 4-3 describes the effects of adjusting the primary color hues.
Default
Table 4-3. Effects of Primary Color Hue Adjustments
Primary Color
Press to move the color...
Closer to magenta
Closer to red
Press to move the color...
Closer to yellow
Closer to green
Red
Yellow
Green
Cyan
Blue
Closer to yellow
Closer to green
Closer to cyan
Closer to blue
Closer to cyan
Closer to magenta
Closer to red
Magenta
Closer to blue
•
Saturation: This slidebar adjusts the color saturation level – the amount of that color in a
video image. Lower settings produce less saturated colors; a setting of “-30” removes that
color from the image entirely. If the saturation is too high, that color will be overpowering
and unrealistic.
•
•
Default: To reset ALL ICC settings – Hue, Saturation AND Intensity of all six colors – for the
confirm the reset.
To reset only the Hue, Saturation OR Intensity of all six colors for the currently-selected
the BrilliantColor setting. BrilliantColor utilizes a new color-processing algorithm and system
level enhancements to enable higher picture brightness while providing truer, more vibrant
colors. To enable BrilliantColor, set it to On; to disable it, set it to Off.
Vidikron Vision 85 Owner’s Operating Manual
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Adjust menu. Noise reduction is useful for improving the signal-to-noise ratio of
video signals. Set it to Off, 1, 2 or 3, as needed, keeping in mind that higher settings (which
reduce high frequencies) may also “soften” the image.
noise” in MPEG-compressed video signals (digital broadcasts or DVDs). Set it to Off, 1, 2 or 3,
as needed to minimize distortion around the edges of moving objects, moving artifacts
around edges and/or blotchy noise patterns superimposed over the objects.
Adjust menu to apply edge enhancement to images, giving the impression of added depth.
Set it to Off, 1, 2, or 3 as desired.
according to the color content in the signal, to produce the best picture quality. Select
3 as desired. Selecting “3” results in a higher average white level than the other settings.
Default: To reset all picture quality settings for the current input to their factory-default
The Vision 85 provides nine adjustable white balance parameters, allowing precise
adjustment of the intensity of the red, blue and green color components in the dark areas
(Offset), light areas (Gain) and “mid-tone” areas (Gamma).
➤
White Balance
Mem. Select
Gamma
Red Gamma
Green Gamma
Blue Gamma
You can adjust these parameters as needed and store them in any of six presets (memory
locations). The selected white balance preset can, in turn, be associated with a “Picture
associate a white balance preset with the picture memory preset of the same name;
however, you can associate a white balance preset with any picture memory preset.
1
0
0
0
Balance menu.
Gain
Red Gain
Green Gain
Blue Gain
0
0
0
Offset
Red Offset
Green Offset
Blue Offset
0
0
0
Default: To reset the Gamma, Gain and Offset settings for the currently-selected white
Then, select Yes to confirm the reset.
Default
56
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Select HD/RGB Adj. from the Main Menu to view input signal resolution and timing
horizontal frequency and vertical frequency of the input current signal.
HD/RGB Adj.
Frequency
0
Phase
H-Shift
V-Shift
0
0
0
Default
Special Modes
Signal info
Auto Setup
Select Options from the Main Menu to perform the following projector configuration tasks.
image.
Options
Image Shift
Subtitle
Default
0
0
small increments.
Overscan
+
-
5%
Image Shift and Subtitle can only be adjusted for certain 1080i signals.
Adjust White Level
Adjust Black Level
0
0
Note
On
LED
Lamp Hours
OSD
On
3
Signal Type
Color Space
HDMI Black Level
Background
Power Save
menu, then select Yes to confirm the reset.
Auto
0
LEDs.
Baud Rate
9600 bps
•
When set to ON, the LEDs indicate operating status as described in VX-2000d at a Glance
Fan Mode
Orientation
Factory Default
2
FF
on page 5.
Off, the LED function is automatically set to On.
Note
•
When set to OFF, the LEDs illuminate when the Vision 85 is in standby mode, warming up
or indicating an error condition; otherwise, they are off.
OSD: When you select an aspect ratio or input with the remote control (or from the VHD
Controller), the Vision 85 displays your selection on-screen. To prevent the display of these
Vidikron Vision 85 Owner’s Operating Manual
57
Download from Www.Somanuals.com. All Manuals Search And Download.
(encoding method):
•
•
•
Choose Auto to have the Vision 85 automatically detect the signal type.
Choose RGB (1) for RGB-encoded video signals.
Choose YCrCb4:4:4 (2) for uncompressed, component video. This encoding method uses a
“luminance” signal (Y) to represent brightness and “difference” signals (Cb and Cr) to
represent colors.
•
Choose YCrCb4:2:2 (3) for compressed, component video (similar to YCrCb4:4:4).
In most situations, selecting Auto produces the most accurate colors. If it does not, try the
other choices and select the one that does.
Color Space: “Color Space” determines how the color components of an analog input signal
specify the color space to use. In most situations, selecting Auto produces the most accurate
colors. If it does not, try the other choices and select the one that does.
HDMI Black Level: This control compensates for incoming elevated black levels present in
certain video signals. When you set it to Auto, the Vision 85 automatically determines the
best setting according to the incoming video signal type. For some types of video, you may
want to override the setting. Set it to 0 IRE if blacks appear elevated (dark gray). If blacks
appear “crushed” (too dark), set it to 7 IRE.
image background – solid blue, solid black or the Vidikron logo welcome screen. The
Background appears when no incoming signal is present.
features of the Vision 85.
•
RS-232C Port: When this option is set to On, the RS-232 port is always active and using
power, even when the projector is in standby mode. When set to Off, the RS-232 port is
inactive and does not consume power when the projector is in standby mode.
Always set this option to On. Doing otherwise may disrupt
communication between the projector and VHD Controller.
Caution
•
Auto Power Off: When this option is set to On, the projector enters standby mode after
15 minutes of inactivity (no input signal). Five minutes before this is to occur, the message
“Enter STANDBY mode in 5 min.” appears on-screen. This message updates to indicate the
amount of time before the projector enters standby mode.
When set to Off, the projector remains in the “power on” state regardless of the presence
or absence of an input signal.
When you set the Auto Power Off function to Off, the LED function (refer to
4-57) is automatically set to On.
Note
change the data rate of the RS-232 connection between the projector and the VHD
Controller. The default setting is 9600 bps. Do not change it unless specifically instructed
to do so by Vidikron Technical Support.
58
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
control to prevent it from overheating. Set it to High Altitude (2) to run the fan at high speed;
set it to Normal (1) to run the fan at normal speed.
Factory Default: To reset all projector settings (including image settings) back to their
message appears, select All Reset to perform the reset or Return to cancel. This action is
not undoable. Proceed with caution!
Language setting.
Note
Vidikron Vision 85 Owner’s Operating Manual
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
60
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
5Maintenance and Troubleshooting
The lamp should be replaced when it reaches the end of its life (typically 2000 hours), or
sooner if a noticeable degradation in brightness occurs. Contact your Vidikron dealer to
obtain a replacement lamp.
5.1
Lamp Replacement
1. Turn off the projector and unplug the power cord. Allow the projector to cool down for
approximately 45 minutes prior to removing the lamp assembly for replacement.
2. Using a Phillips screwdriver, loosen the two
Lamp Cover screws on the side of the
projector and remove the cover.
REMOVE
THESE SCREWS
3. Remove the three Phillips round-head lamp assembly mounting screws. These are
identified by arrows pointing to them on the lamp housing.
4. Grasp the lamp assembly handle and pull gently, removing the lamp module from the
projector housing.
5. Install the new lamp module. Secure it in place with the three screws that you removed
in Step 3.
6. Replace the lamp cover and re-tighten the two Lamp Cover screws.
7. Re-connect the AC power cord to the projector.
8. Reset the Lamp Hour counter by doing either of the following:
•
DOWN and RIGHT buttons simultaneously. Then, press the ON button.
•
ENTER button, press the POWER ( ) button.
When you do, “LAMP 0000H” appears on-screen to confirm the counter reset.
Always reset the Lamp Hour counter when you replace the lamp. Do this
only if you have just installed a new lamp. This will ensure that number of
Note
hours logged on the lamp is accurate.
Vidikron Vision 85 Owner’s Operating Manual
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 5-1 provides some general guidelines for troubleshooting problems you may
encounter with the Vision 85.
5.2
Troubleshooting Tips
If you encounter an issue not described here or in Section 3 (refer to Installation
contact your Vidikron dealer or Vidikron Technical Support.
Table 5-1. Troubleshooting Chart
Symptom
Possible Cause(s)
Solution
The projector does not turn on
after initial installation. The
power LED on the front of the
VHD Controller lights red after
you press the power button.
•
•
The Vision 85 is not
plugged in or the AC outlet
is not active.
The serial connection from
the VHD Controller to the
Vision 85 is incorrect.
•
•
Ensure that the Vision 85 is
plugged in and that the AC
outlet is active.
Ensure that the RS-232
output from the VHD
Controller is properly
connected to the RS-232C
port on the Vision 85 (see
•
•
The remote control
batteries have run out.
•
•
Replace the batteries.
The projector and VHD
Controller are both on, but
there is no picture and
on-screen menus do not
appear.
Faulty or incorrect video
connection between the
VHD Controller and the
Vision 85.
Ensure that the HDMI
output from the VHD
Controller is properly
connected to the HDMI
input on the Vision 85 (see
The projector and
•
•
Incorrect source selection.
Source component is not
turned on.
Source component is
connected incorrectly or
not at all.
•
•
Select the correct source.
Turn on the source.
VHD Controller are both on
and menus appear on-screen,
but there is no picture.
•
•
Check video connections to
source component.
A projected image from a DVD
is split or otherwise scrambled.
•
DVD player is connected to
the Component input and
set to progressive scan
mode.
•
Turn off progressive scan
on the DVD player. Or,
connect the DVD player to
the HD1 or HD2 input.
Image is too bright and/or
lacks definition in the bright
areas of the image.
•
•
•
Contrast is set too high.
•
•
•
Lower the contrast setting.
Image appears “washed out”
and/or dark areas appear too
bright.
Brightness is set too high.
Lower the brightness
setting.
Colors in the image are
swapped (for example, reds
appear blue or vice versa) on
one or more sources.
The Red/Pr, Green/Y or
Blue/Pb outputs from the
source are connected to the
wrong inputs on the VHD
Controller.
Ensure that the source
outputs are connected to
the correct VHD Controller
input.
62
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 5-1. Troubleshooting Chart (continued)
Symptom
Possible Cause(s)
Solution
Image geometry is incorrect.
•
Incorrect aspect ratio
selection.
•
Select the aspect ratio that
best matches the source
image and screen size (refer
•
•
•
Image height may need
adjusting (Vision
85/CineWide only).
•
•
•
Adjust displayed image
height (refer to Display
The projected image is
trapezoidal in shape.
The projector is not
perpendicular to the
screen.
Adjust the projection angle.
The projector will not turn
back on after it was powered
down, or the image disappears
during operation.
The projector will not turn
on for two minutes after
power-down, to protect the
lamp.
Wait two minutes until the
LED at the front of the VHD
Controller turns red.
•
The lamp has failed or
reached its usage limit of
2000 hours.
•
Replace the lamp.
Vidikron Vision 85 Owner’s Operating Manual
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
64
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
6Serial Communications
To interface the VHD Controller with a home theater automation/control system or a PC
running terminal emulation software, connect it to your control system or PC as shown in
6.1
RS-232 Connection and
Port Configuration
Configure the RS-232 controller or PC serial port as follows: no parity, 8 data bits, 1 stop bit
and no flow control. Set the baud rate to 19200, to match that of the VHD Controller RS-232
port.
Serial commands to the VHD Controller take the following form:
6.2
Serial Command Syntax
•
•
Commands are not case-sensitive.
For a single command that takes no parameters, type the command followed by a
carriage return; for example, to set the aspect ratio to Letterbox, type
LETTERBOX <Enter>.
•
•
For a single command that takes a parameter, type the command, a space or a comma
and the desired value followed by a carriage return; for example, to set the brightness to
-10, type BRIGHTNESS -10 <Enter>or BRIGHTNESS,-10 <Enter>.
You can also send a string of multiple commands on a single line, separated by commas.
For example, COMPOSITE,BRIGHTNESS 100,ANAMORPHIC <Enter>switches to
the Composite video input, sets the brightness to 100 and sets the aspect ratio to
Anamorphic. Command strings can be up to 255 characters long.
Avoid combining the ONor POWER 1commands with other commands on a
Note
single line. After sending ONor POWER 1, allow at least 15 seconds for the
VHD Controller to power up. Once it does, it will accept and properly execute
multiple serial commands.
Table 6-1 lists the RS-232 command set. The “Parameter (min/max)” column shows the valid
parameter ranges, or “NA” for commands that take no parameters.
When you enter a valid command, the VHD Controller executes it and acknowledges it with a
plus sign on the command line (+ >). When you enter an invalid command – one that is
misspelled or followed by values outside the valid range for that command – the VHD
Controller ignores it and returns a minus sign (- >).
Table 6-1. Serial Commands
Parameter
(min/max)
Value
Stored?
Command
Description
Power On/Off Commands
OFF
ON
NA
NA
NA
NA
NA
Turns projector off
Turns projector on
NA
0/1
NA
POWER
Turns projector on and off
Returns power status
POWER?
Vidikron Vision 85 Owner’s Operating Manual
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-1. Serial Commands (continued)
Parameter
(min/max)
Value
Stored?
Command
Description
Input Selection Commands
COMPONENT
COMPOSITE
HDMI1
NA
YES
YES
YES
YES
YES
YES
NA
Selects the Component input
Selects the Composite video input
Selects the HDMI 1 input
Selects the HDMI 2 input
Selects the HD 1 input
NA
NA
NA
NA
NA
NA
NA
NA
HDMI2
HD1
HD2
Selects the HD 2 input
INPUT?
Returns active input
SVIDEO1
SVIDEO2
YES
YES
Selects the S-Video 1 input
Selects the S-Video 2 input
Aspect Ratio Commands
ANAMORPHIC
16:9
NA
YES
Selects the Anamorphic aspect ratio
ASPECT?
NA
NA
NA
NA
NA
NA
NA
NA
YES
YES
Returns current aspect ratio
ASPECTIN?
ASPECTOUT?
CINEMA
Returns the input source aspect ratio
Returns output screen size
Selects the Cinema aspect ratio
Selects the Letterbox aspect ratio
LETTERBOX
STANDARD
4:3
NA
YES
Selects the Standard (4:3) aspect ratio
INTELLIWIDE
INTELLI235
NA
NA
YES
YES
Selects the IntelliWide aspect ratio
Selects the IntelliWide 2.35 aspect ratio
(available only on the Vision 85/CineWide
and only on the analog inputs)
66
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-1. Serial Commands (continued)
Parameter
(min/max)
Value
Stored?
Command
Description
Picture Adjust Commands (not available on HDMI 1 or HDMI 2 inputs)
BRIGHTNESS
BRIGHTNESS?
CHROMADELAY
CHROMADELAY?
COLOR
-100/100
NA
YES
NA
Sets a value for brightness
Returns brightness setting value
Sets a value for input color chroma delay
Returns input color chroma delay setting
Sets a value for color
-12/12
NA
YES
NA
-100/100
NA
YES
NA
COLOR?
Returns color setting value
CONTRAST
CONTRAST?
FILMMODE
FILMMODE?
FILTER
-100/100
NA
YES
NA
Sets a value for contrast
Returns contrast setting value
Sets Film Mode off (0) or on (1)
Returns Film Mode setting (0 = off; 1 = on)
Sets a value for input color noise filter
Returns input color noise filter setting
Adjusts phase
0/1
YES
NA
NA
0/15
NA
YES
NA
FILTER?
PHASE
0/3
YES
NA
PHASE?
NA
Returns phase setting value
Sets a value for sharpness
SHARPNESS
SHARPNESS?
TINT
-6/6
YES
NA
NA
Returns sharpness setting value
Sets a value for tint
-100/100
NA
YES
NA
TINT?
Returns tint setting value
Image Preset Commands (not available on HDMI 1 or HDMI 2 inputs)
CUSTOM1
CUSTOM2
DAY
NA
NA
NA
NA
NA
YES
YES
YES
YES
NA
Loads “Custom 1” image preset
Loads “Custom 2” image preset
Loads “ISF Day” image preset
Loads “ISF Night” image preset
NIGHT
PRESET?
Returns currently-selected preset
(ISF Day, ISF Night, Custom 1 or Custom 2)
Vidikron Vision 85 Owner’s Operating Manual
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-1. Serial Commands (continued)
Parameter
(min/max)
Value
Stored?
Command
Description
Input Position Commands (not available on HDMI 1 or HDMI 2 inputs)
IHEIGHT
IHEIGHT?
IHPOS
-100/100
NA
YES
NA
Sets the value for input height
Returns input height value
-100/100
NA
YES
NA
Sets a value for horizontal input position
Returns input horizontal position value
Sets a value for vertical input position
Returns input vertical position value
Sets the value for input width
IHPOS?
IVPOS
-100/100
NA
YES
NA
IVPOS?
IWIDTH
-100/100
NA
YES
NA
IWIDTH?
OVERSCAN
OVERSCAN?
Returns input horizontal width value
Sets the overscan percentage
0/10
YES
NA
NA
Returns overscan percentage
Output Shift Commands (not available on HDMI 1 or HDMI 2 inputs)
OHEIGHT
OHEIGHT?
OHPOS
-100/100
NA
YES
NA
Sets the value for output height
Returns output height value
-100/100
NA
YES
NA
Sets the value for output horizontal position
Returns output horizontal position value
Sets the value for output vertical position
Returns output vertical position value
Sets the value for output width
OHPOS?
OVPOS
-100/100
NA
YES
NA
OVPOS?
OWIDTH
OWIDTH?
-100/100
NA
YES
NA
Returns output horizontal width value
68
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-1. Serial Commands (continued)
Parameter
(min/max)
Value
Stored?
Command
Description
Miscellaneous Commands
BKGND
-100/100
YES
Sets the background color for 4:3 aspect ratio
(-100 = black; 100 = white)
BKGND?
NA
NA
NA
NA
NA
YES
Returns background setting value
Returns projector manufacture date
DATE?
HDINPUTRES
Sets YPbPr input resolution and refresh rate
for HD1/HD2, as follows:
0 = 480i
1 = 480p
2 = 576i
3 = 576p
4 = 720p / 60 Hz
5 = 1080i / 60 Hz
6 = 720p / 50 Hz
7 = 1080i / 25 Hz
Any other value = Auto
HWVER?
INRES?
LENS1?
RGBNN
NA
NA
NA
NA
NA
NA
NA
NA
Returns hardware version number
Returns input resolution
Returns Lens 1 configuration
Sets output color space to RGB with negative
horizontal and vertical sync
RGBPP
RGBS
NA
NA
NA
NA
NA
NA
Sets output color space to RGB with positive
horizontal and vertical sync
Sets output color space to RGB with
composite sync
STATUS
Returns current operating status (power,
input source, input resolution and input
aspect ratio)
SWVER?
TRIGGER
NA
1/3
NA
Returns software version number
YES
Assigns trigger to currently-selected aspect
ratio
Vidikron Vision 85 Owner’s Operating Manual
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-1. Serial Commands (continued)
Parameter
(min/max)
Value
Stored?
Command
Description
The following serial commands are meant to emulate buttons on the remote control or VHD
Controller front panel. Each button has its own serial command, so effectively it is as if you were
using the IR remote only you’ll be doing so via serial commands. These commands provide active
OSD responses just like the IR remote.
DOWN
ENTER
LEFT
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
Down-Arrow ( ) key
ENTER key
Left-Arrow ( ) key
MENU
MENU
RIGHT
UP
Right-Arrow ( ) key
Up-Arrow ( ) key
70
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
7Specifications
7.1
Vision 85 Specifications
Table 7-1. Vision 85 Specifications
Projector Type:
Native Resolution:
Aspect Ratios:
Digital Light Processing (DLP), single-chip, 16:9 DMD
1920 x 1080 (16:9)
Refer to Table 7-2
Video Standards:
DTV Compatibility:
Scan Frequency:
Refer to Table 7-2
480p, 720p, 1080i, 1080p
Horizontal: 15 - 81 kHz
Vertical: 43 - 100 Hz
Picture Size (16:9 Screen):
Recommended Width: 72 - 96 in.
Maximum Width: 200 in.
Throw Distance
Vision 85: 1.86 to 2.45
(Factor x Screen Width):
Vision 85/CineWide: 1.92 to 2.45
Horizontal and Vertical
Offset:
Horizontal: None
Vertical: 50% of screen height up or down
Lamp:
220 Watts
Estimated Lamp Life:
Inputs (from VHD Controller):
2000 hours
(1) HDMI with HDCP, (1) RS-232
Vidikron Vision 85 Owner’s Operating Manual
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 7-1. Vision 85 Specifications (continued)
Brightness and Contrast
(variable, depending on VAC
calibration):
Cinema Standards Measurement System (CSMS)
Specifications
-
Brightness: TBD
-
Contrast Ratio: TBD
These measurements are taken from the projector in a controlled, home
theater environment. All measurements are made to ANSI/NAPM
IT7.228-1997 specifications using the Photo Research PR-650
SpectraColorimeter and Minolta LS-100 Luminance Meter, Video
Essentials test DVD and a 1.3 gain, 72-inch wide screen. The projector is
calibrated to a color temperature of 6,500K and has a minimum of 150
hours of usage.
The foot-Lambert (fL) is the unit of measurement used in commercial
movie theaters to express image brightness at the screen surface. The
Society of Motion Picture and Television Engineers (SMPTE) specifies 16
fL as the target image brightness for film-based projectors using an
open gate (without film in the projector). More importantly, today
SMPTE specifies 12 fL as the target image brightness in Digital Cinema
theaters. The foot-Lambert measurement is dependent on screen size,
screen gain and projector light output.
Home Theater Calibration Specifications
-
Light Output: TBD
-
Contrast Ratio: TBD
These specifications are obtained by calibrating the projector as
described above for CSMS measurements.
Industry-Standard Specifications
-
Light Output: TBD
-
Contrast Ratio: TBD
These are typical projector brightness and contrast specifications found
in most companies’ sales literature. Vidikron includes these
measurements in its literature to allow for direct comparison with other
manufacturers’ projectors. These measurements are typically taken at
9,000K to 13,000K to get expected performance data when the projector
is used in professional, commercial and industrial displays.
Power Requirements:
100 to 240 VAC (auto-sensing), 50/60 Hz, 375 Watts
Operating Environment:
40°F to 95°F (5°C to 35°C), 0% to 90% humidity
(non-condensing)
Dimensions:
Weight (without lens):
Regulatory Approvals:
Limited Warranty:
50 lbs. (22.68 kg)
Complies with FCC, CE C-Tick
Projector: Two (2) years parts and labor from the date of delivery
to the end user.
Lamp: 1000 hours or six (6) months, whichever comes first.
Specifications are subject to change without notice.
72
Vidikron Vision 85 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 7-2 lists the VHD Controller specifications.
7.2
VHD Controller
Specifications
Table 7-2. VHD Controller Specifications
Aspect Ratios:
Video Standards:
Inputs:
4:3, Letterbox, 16:9, IntelliWide, Cinema, IntelliWide 2.35
NTSC, PAL
(1) Composite; (2) S-Video; (1) Component; (2) HD-R (Pr), G (Y), B
(Pb), H, V; (2) HDMI with HDCP
Outputs:
HDMI with HDCP
Control Options:
-
-
-
Discrete infrared remote
Serial commands via RS-232
Front-panel controls
RS-232 Communication
Parameters:
19200 bps, no parity, 8 data bits, 1 stop bit, no flow control
Trigger Outputs:
(3) +12 VDC, each rated at 750 mA and thermal fuse-protected
150 Mega Samples per Second (MSPS)
Bandwidth:
Power Requirements:
Operating Environment:
100 to 240 VAC (auto-sensing), 50/60 Hz, 160 Watts
40°F to 95°F (5°C to 35°C), 0% to 90% humidity
(non-condensing)
Dimensions:
Width = 17.50 inches (444.5 mm)
Depth = 11.19 inches (284.1 mm)
Height = 3.75 inches (95.3 mm)
Weight:
13.0 lbs. (5.90 kg)
Regulatory Approvals:
Limited Warranty:
Complies with FCC, CE C-Tick
Two (2) years parts and labor from the date of delivery to the end
user.
Specifications are subject to change without notice.
Vidikron Vision 85 Owner’s Operating Manual
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
RUMA-011220
rev. 01-10-07 v1.0
Vidikron
2900 Faber Street
Union City, CA 94587
510-324-5900
Fax 510-324-5905
1-888-4-VIDIKRON
SERIAL NUMBER
Download from Www.Somanuals.com. All Manuals Search And Download.
|