Renesas Network Card M3062NT3 RPD E User Guide

M3062NT3-RPD-E

Emulation Pod for M16C/62 Group M16C/62N and M16C/30 Group M16C/30L

User's Manual

Rev. 1.00

June 16, 2003

REJ10J0113-0100Z

Download from Www.Somanuals.com. All Manuals Search And Download.

Preface

The M3062NT3-RPD-E is an emulation pod for the M16C/62 Group M16C/62N and M16C/30

Group M16C/30L of 16-bit MCUs. It is used with a PC4701 emulator.

This user's manual mainly describes specifications of the M3062NT3-RPD-E emulation pod and how

to setup it. For details on the following products, which are used with M3062NT3-RPD-E, refer to

each product's user's manual.

• Emulator:

PC4701 User's Manual

• Emulator debugger:

M3T-PD30 User's Manual

All the components of this product are shown in "2.1 Package Components" (page 22) of this user's

manual. If there is any question or doubt about this product, contact your local distributor.

To use the product properly

Precautions for Safety

• In both this user's manual and on the product itself, several icons are used to insure

proper handling of this product and also to prevent injuries to you or other persons,

or damage to your properties.

• The icons' graphic images and meanings are given in "Chapter 1. Precautions for

Safety". Be sure to read this chapter before using the product.

When using outside Japan

• When using in Europe, the United States, or Canada, be sure to use both the emulator

and the emulation pod which meet local standards. EMI standards are not met when

the M3062NT3-RPD-E is used with the PC4700H emulator.

( 3 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

Chapter 1. Precautions for Safety ...................................................................................................... 9

1.1 Safety Symbols and Meanings ....................................................................................... 10

WARNINGS

Warning for Installation ................................................................................................. 11

Warnings for Use Environment ...................................................................................... 11

CAUTIONS

Caution to Be Taken for Modifying This Product.......................................................... 11

Cautions to Be Taken for Handling This Product .......................................................... 11

Cautions to Be Taken for Turning On the Power ........................................................... 11

IMPORTANT

Note on Malfunctions in the PC4701 System ................................................................ 12

Notes on Downloading Firmware .................................................................................. 12

Notes on the Self-check .................................................................................................. 12

Note on Quitting the Emulator Debugger ...................................................................... 12

Note on Final Evaluation ................................................................................................ 12

Notes on Power Supply to the Target System ................................................................ 12

Note on Clock Supply to the MCU ................................................................................ 13

Note on RESET* Input................................................................................................... 13

Note on NMI* Input ....................................................................................................... 13

Note on RDY* Input ...................................................................................................... 13

Notes on HOLD* Input .................................................................................................. 13

Notes on Setting the Work Area When Starting Up the Emulator Debugger ................ 13

Note on Stack Area......................................................................................................... 14

Notes on MAP References and Settings......................................................................... 14

Note on Operation When Not Executing the User Program .......................................... 15

Note on Making an MCU file......................................................................................... 15

Notes on Maskable Interrupts......................................................................................... 15

Notes on Address-Match Interrupt ................................................................................. 15

Note on BRK Instruction and BRK Interrupt ................................................................. 15

Notes on Software and Hardware Breaks....................................................................... 16

Note on Stop and Wait Modes........................................................................................ 16

Note on Watchdog Function........................................................................................... 16

Note on DMA Transfer .................................................................................................. 16

Note on Pullup Control................................................................................................... 16

Note on Reading Internal Resources of the MCU .......................................................... 17

Note on Protect Register (PRC2) ................................................................................... 17

Note on Accessing Address 00000h ............................................................................... 17

Note on Differences Between the Actual MCU and Emulator ...................................... 18

Note on Debugging Operations After Releasing a Reset from the Target ..................... 19

Note on Emulating External Area .................................................................................. 19

Chapter 2. Preparation ..................................................................................................................... 21

2.1 Package Components ..................................................................................................... 22

2.2 Other Tool Products Required for Development ........................................................... 22

( 4 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

2.3 Name of Each Part ......................................................................................................... 23

(1) System Configuration ............................................................................................... 23

(2) Inside of the Emulation Pod...................................................................................... 24

2.4 When Using This Product for the First Time ................................................................. 25

(1) Making an MCU File ................................................................................................ 25

(2) Setting the Work Area .............................................................................................. 25

(3) Downloading Firmware ............................................................................................ 26

(4) Self-check ................................................................................................................. 26

Chapter 3. Setting Up ...................................................................................................................... 27

3.1 Removing and Closing the Upper Cover ....................................................................... 28

3.2 Each Setting ................................................................................................................... 29

3.3 Selecting Clock Supply and Replacing Oscillator Circuit Boards ................................. 30

(1) Clock Supply to the MCU ........................................................................................ 30

(2) Using the Oscillator Circuit on the Target System ................................................... 31

(3) Changing the Internal Oscillator Circuit of the Emulation Pod................................ 32

(4) Replacing Oscillator Circuit Boards ......................................................................... 33

3.4 Switch Settings ............................................................................................................... 34

(1) Toggle Switches SW1 to SW5 on the M30620T3-PRT Board (MCU-dependent 1) ... 34

(2) Jumper Switches JP1 and JP2 on the M30620T3-PRT Board (MCU-dependent 1) .... 36

3.5 Installing and Removing Pullup Resistors ..................................................................... 37

3.6 A-D Conversion Bypass Capacitors............................................................................... 38

3.7 Connecting the PC4701.................................................................................................. 39

(1) Connecting the Cable to the PC4701 ........................................................................ 39

(2) Connecting the Cable to the Emulation Pod ............................................................. 40

3.8 Connecting the Target System ....................................................................................... 41

(1) Connecting to a 100-pin LCC Socket ....................................................................... 42

(2) Connecting to an 80-pin 0.65-mm-pitch Foot Pattern (Part 1) ................................. 43

(3) Connecting to an 80-pin 0.65-mm-pitch Foot Pattern (Part 2) ................................. 44

(4) Connecting to a 100-pin 0.65-mm-pitch Foot Pattern (Part 1) ................................. 45

(5) Connecting to a 100-pin 0.65-mm-pitch Foot Pattern (Part 2) ................................. 46

(6) Connecting to a 100-pin 0.65-mm-pitch Foot Pattern (Part 3) ................................. 47

(7) Connecting to a 100-pin 0.5-mm-pitch Foot Pattern (Part 1) ................................... 48

(8) Connecting to a 100-pin 0.5-mm-pitch Foot Pattern (Part 2) ................................... 49

(9) Connecting to a 100-pin 0.5-mm-pitch Foot Pattern (Part 3) ................................... 50

(10) Connecting to a 100-pin 0.4-mm-pitch Foot Pattern .............................................. 51

Chapter 4. Usage ............................................................................................................................. 53

4.1 Turning On the Power .................................................................................................... 54

(1) Checking Connections of the Emulator System ....................................................... 54

(2) Turning ON/OFF the Power ..................................................................................... 54

(3) LED Display When the PC4701 Starts Up Normally............................................... 55

4.2 Downloading Firmware ................................................................................................. 56

(1) When It is Necessary to Download Firmware .......................................................... 56

(2) Downloading Firmware in Maintenance Mode ........................................................ 56

( 5 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

4.3 Self-check....................................................................................................................... 57

(1) Self-check Procedure ................................................................................................ 57

(2) If an Error is Detected in the Self-check................................................................... 57

Chapter 5. Specifications ................................................................................................................. 59

5.1 Specifications ................................................................................................................. 60

5.2 Operation Timing in Memory Expansion and Microprocessor Modes ......................... 61

(1) Separate Bus, No-Wait ............................................................................................. 61

(2) Separate Bus, With Wait, Accessing External Memory Area .................................. 63

(3) Multiplex Bus Timing............................................................................................... 65

(4) Timing Requirements ............................................................................................... 67

5.3 Connection Diagram ...................................................................................................... 68

5.4 External Dimensions ...................................................................................................... 70

(1) External Dimensions of the Emulation Pod.............................................................. 70

(2) External Dimensions of the Converter Board M30800T-PTC ................................. 71

(3) External Dimensions of the Converter Board M3T-F160-100NSD ......................... 72

(4) External Dimensions of the Converter Board M3T-F160-100NSE ......................... 72

Chapter 6. Troubleshooting ............................................................................................................. 73

6.1 Flowchart to Remedy the Troubles ................................................................................ 74

6.2 When the Emulator Debugger Does Not Start Up Properly .......................................... 75

(1) When the LED Display of the PC4701 is Abnormal ................................................ 75

(2) Program Window is Not Displayed at Debugger Startup (Target Connected) ............. 76

(3) Program Window is Not Displayed at Debugger Startup (Target Not Connected) ...... 77

6.3 How to Request for Support........................................................................................... 77

Chapter 7. Maintenance and Guarantee........................................................................................... 79

7.1 Maintenance ................................................................................................................... 80

7.2 Guarantee ....................................................................................................................... 80

7.3 Repair Provisions ........................................................................................................... 80

7.4 How to Request for Repair............................................................................................. 81

( 6 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

Terminology

Some specific words used in this user's manual are defined as follows:

Emulator system

This means an emulator system built around the PC4701 emulator. The PC4701 emulator system is

configured with an emulator main unit, emulation pod, host machine and emulator debugger.

Emulator main unit (Hereafter PC4701)

This means a generic name for emulators for M16C, 7700, 740 Families. Take note of the fact that

the M3062NT3-RPD-E (this product) does not support the PC4701L and PC4700L emulators. For

details on specific models of PC4701, visit the Renesas Tools Homepage at http://www.renesas.com/

en/tools

Emulation pod

This means M3062NT3-RPD-E (this product). This emulation pod is for the M16C/62 Group M16C/

62N and M16C/30 Group M16C/30L. It is used with the emulator main unit PC4701.

Emulator debugger

This means a software tool M3T-PD30 for M16C/60, M16C/20 and M16C/10 Series MCUs. The

M3T-PD30 controls the emulator from the host machine through various interfaces.

Host machine

This means a personal computer used to control the emulator and emulation pod.

Firmware

Program that analyzes contents of communication with the emulator debugger and controls the

emulator hardware. This program is installed in the EEPROM. This program is downloadable from

the emulator debugger to upgrade the firmware or to support other MCUs.

Target MCU

This means the microcomputer you are going to debug.

Target system

This means a user's application system using the microcomputer to be debugged.

User program

This means an application program to be debugged.

Evaluation MCU

This means the microcomputer mounted on the emulation pod which is operated in the specific mode

for tools.

In this user's manual, this symbol is used to show active LOW (e.g. RESET*: Reset signal).

( 7 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

MEMO

( 8 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 1. Precautions for Safety

This chapter describes precautions for using this product safely and properly. For precautions for the emulator main unit

and the emulator debugger, refer to each user's manual included with your product.

1.1 Safety Symbols and Meanings ................................................................................................... 10

WARNING

Warning for Installation ............................................................................................. 11

Warnings for Use Environment ................................................................................. 11

CAUTION

Caution to Be Taken for Modifying This Product ..................................................... 11

Cautions to Be Taken for Handling This Product...................................................... 11

Cautions to Be Taken for Turning On the Power ...................................................... 11

IMPORTANT

Note on Malfunctions in the PC4701 System............................................................ 12

Notes on Downloading Firmware .............................................................................. 12

Notes on the Self-check ............................................................................................. 12

Note on Quitting the Emulator Debugger .................................................................. 12

Note on Final Evaluation ........................................................................................... 12

Notes on Power Supply to the Target System ........................................................... 12

Note on Clock Supply to the MCU............................................................................ 13

Note on RESET* Input .............................................................................................. 13

Note on NMI* Input................................................................................................... 13

Note on RDY* Input .................................................................................................. 13

Notes on HOLD* Input.............................................................................................. 13

Notes on Setting the Work Area When Starting Up the Emulator Debugger ........... 13

Note on Stack Area .................................................................................................... 14

Notes on MAP References and Settings .................................................................... 14

Note on Operation When Not Executing the User Program ...................................... 15

Note on Making an MCU file .................................................................................... 15

Notes on Maskable Interrupts .................................................................................... 15

Notes on Address-Match Interrupt............................................................................. 15

Note on BRK Instruction and BRK Interrupt ............................................................ 15

Notes on Software and Hardware Breaks .................................................................. 16

Note on Stop and Wait Modes ................................................................................... 16

Note on Watchdog Function ...................................................................................... 16

Note on DMA Transfer .............................................................................................. 16

Note on Pullup Control .............................................................................................. 16

Note on Reading Internal Resources of the MCU ..................................................... 17

Note on Protect Register (PRC2) ............................................................................... 17

Note on Accessing Address 00000h .......................................................................... 17

Note on Differences Between the Actual MCU and Emulator .................................. 18

Note on Debugging Operations After Releasing a Reset from the Target ................ 19

Note on Emulating External Area ................................................................................ 19

( 9 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 1. Precautions for Safety

In both the user's manual and on the product itself, several icons are used to insure proper handling

of this product and also to prevent injuries to you or other persons, or damage to your properties.

This chapter describes the precautions which should be taken in order to use this product safely and

properly. Be sure to read this chapter before using this product.

1.1 Safety Symbols and Meanings

If the requirements shown in the "WARNING"

sentences are ignored, the equipment may

cause serious personal injury or death.

WARNING

If the requirements shown in the "CAUTION"

sentences are ignored, the equipment may

malfunction.

CAUTION

It means important information on using this

product.

IMPORTANT

In addition to the three above, the following are also used as appropriate.

means WARNING or CAUTION.

Example:

CAUTION AGAINST AN ELECTRIC SHOCK

means PROHIBITION.

Example:

DISASSEMBLY PROHIBITED

means A FORCIBLE ACTION.

Example:

UNPLUG THE POWER CABLE FROM THE RECEPTACLE.

The following pages describe the symbols "WARNING", "CAUTION", and "IMPORTANT".

( 10 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

WARNING

Warning for Installation:

• Do not set this product in water or areas of high humidity. Make sure that the main unit does not

get wet. Spilling water or some other liquid into the main unit can cause an unrepairable damage.

Warnings for Use Environment:

• The emulation pod is air-cooled with the ventilation slot. Therefore, do not block the ventilation

slot. When heated to high temperatures, the emulation pod may not work properly.

• This equipment is to be used in an environment with a maximum ambient temperature of 35°C. Care

should be taken that this temperature is not exceeded.

CAUTION

Caution to Be Taken for Modifying This Product:

• Do not disassemble or modify this product. Disassembling or modifying this product can cause

damage. Disassembling and modifying the product will void your warranty.

Cautions to Be Taken for Handling This Product:

• Use caution when handling the main unit. Be careful not to apply a mechanical shock.

• Do not touch the connector pins of the emulator main unit and the target MCU connector pins. Static

electricity may damage the internal circuits.

• Do not pull the emulation pod main unit by the flexible cable (FLX120-RPD) for connecting to the

emulator main unit or the flexible cable (FLX64, FLX100, FLX160 or M3T-FLX160C) for

connecting the target system. The cable may cause a break.

• Flexible cable (FLX120-RPD) for connecting to the emulator main unit and the flexible cable

(FLX64, FLX100, FLX160 or M3T-FLX160C) for connecting the target system are different from

earlier models. The slits make them more flexible. However, excessive flexing or force may break

conductors.

• Do not use inch-size screws for this equipment. The screws used in this equipment are all ISO

(meter-size) type screws. When replacing screws, use same type screws as equipped before.

Cautions to Be Taken for Turning On the Power:

• Turn on the power of the emulator and target system as simultaneously as possible.

• Turn off the power of the emulator and target system as simultaneously as possible.

• Do not leave either the emulator or target system powered on, because of leakage current the

internal circuits may be damaged.

• When turning on the power again after shutting off the power, wait about 10 seconds.

( 11 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT

Note on Malfunctions in the PC4701 System:

• If the emulator malfunctions because of interference like external noise, do the following to remedy

the trouble.

(1) Press the system reset switch on the emulator front panel.

(2) If normal operation is not restored after step (1), shut OFF power to the emulator once and then

reactivate it.

Notes on Downloading Firmware:

• Before using this product for the first time, it is necessary to download the dedicated firmware.

Please note that, to do this, it is necessary to start up the emulator main unit in maintenance mode.

For firmware download procedures, see "4.2 Downloading Firmware" (page 56). Once the

firmware has been downloaded, the product can be used by simply turning on the power.

• Do not shut off the power while downloading the firmware. If this happens, the product will not

start up properly. If power is shut off unexpectedly, redownload the firmware in maintenance mode.

• Be sure to disconnect the target system before downloading the firmware.

Notes on the Self-check:

• If the self-check does not result normally (except target status errors), the product may be damaged.

Then, contact your local distributor.

• Be sure to disconnect the target system before executing the self-check. For details on the self-

check, see "4.3 Self-check" on page 57.

Note on Quitting the Emulator Debugger:

• To restart the emulator debugger after it ends, always shut power to the emulator module off once

and then on again.

Note on Final Evaluation:

• Be sure to evaluate your system with an evaluation MCU. Before starting mask production,

evaluate your system and make final confirmation with a CS (Commercial Sample) version MCU.

Notes on Power Supply to the Target System:

• Pin Vcc of the emulator is connected to the target system to observe the voltage of the target system.

Therefore design your system so that the target system is powered by an external power supply.

• The voltage of the target system should be within the MCU's specified range.

• Do not change the voltage of the target system after turning on the power.

( 12 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT

Note on Clock Supply to the MCU:

• Clock can be supplied to the evaluation MCU in one of the following two ways. This is determined

by emulator debugger clock selection.

(1) When Internal is selected:

A clock generated by the oscillation circuit in the emulation pod is supplied to the evaluation

MCU. The clock is continually supplied to the evaluation MCU regardless of "target system

clock status" and "user program execution status".

(2) When External is selected:

Clock supply to the evaluation MCU depends on oscillation status (oscillate/off) of the target

system.

Note on RESET* Input:

• "L" input from the target system to pin RESET* is accepted only while a user program is being

executed (only while the RUN status LED on the PC4701's front panel is lit).

Note on NMI* Input:

• "L" input from the target system to pin NMI* is accepted only while a user program is being

executed (only while the RUN status LED on the PC4701's front panel is lit).

Note on RDY* Input:

• Be sure to input "L" to pin RDY* of the target system during the user program execution (only while

the RUN status LED on the PC4701's front panel is lit). Inputting "L" to pin RDY* during the user

program stopping may cause a malfunction of the emulator.

Notes on HOLD* Input:

• Be sure to input HOLD* of the target system during user program execution (only while the RUN

status LED on the PC4701's front panel is lit). If "L" is input to pin HOLD*, the emulator will not

work normally.

• When inputting "L" to pin HOLD* to run into the HOLD state, P00 to P52 will be in the HOLD

state delaying by 2.5 cycles than the actual MCU (see Table 5.5 and Figure 5.4).

Notes on Setting the Work Area When Starting Up the Emulator Debugger:

• With this product, the emulator uses 32 bytes as a work area in emulation memory. In single-chip

mode, set the work area address at 10000h. In memory expansion or microprocessor mode, set the

work area address in an area other than SFR area (0000h--003FFh), external area of multiplex bus

setting and stack area used by the emulator for reset command execution (0FFF9h--0FFFFh). For

more details, see "2.4 (2) Setting the Work Area" (page 25).

• The top address of the work area should be an even-numbered address.

• Set the work area as MAP=INT.

For example, if the work area is set at 02C00h, the emulator uses 32-byte area of 02C00h to 02C1Fh.

( 13 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT

Note on Stack Area:

• With this product, a maximum 7 bytes of the user stack is consumed. Therefore, ensure the +7 bytes

maximum capacity used by the user program as the user stack area.

If the user stack does not have enough area, do not use areas which cannot be used as stack (SFR

area, RAM area which stores data, or ROM area) as a work area. Using areas like this is a cause

of user program crashes and destabilized emulator control.

Notes on MAP References and Settings:

• For details on referencing and setting MAP information, see the emulator debugger M3T-PD30

user's manual.

Make settings as follows:

(1) MAP = INT

The emulation memory inside this product becomes effective.

Set this at MCU internal ROM debugging.

(2) MAP = EXT

The emulation memory inside this product is not used.

Set this where the MCU internal resource (SFR, RAM) or resources on the target system are

used.

• Be sure to set the SFR area and RAM area of the MCU to EXT, and the reserved area of the MCU

to INT.

• Be sure to set mappings in word units.

• When setting 0FFF9h to 0FFFFh to EXT:

This product uses the 7 byte area 0FFF9h through 0FFFFh as the stack area. If this 7 byte memory

cannot be read or written to, reset cannot be properly effected. As a result, you need to alter the map

settings if the condition given below is met.

(1) With the system which shifts from the single-chip mode to memory expansion (or micropro-

cessor) mode, using the 7 byte area of 0FFF9h to 0FFFFh set to EXT.

(2) With the system which starts up in microprocessor mode, using the 7 byte area of 0FFF9h to

0FFFFh set to EXT and there is not enough memory to read or write.

The procedures to alter the MAP settings when the conditions (1) or (2) above are met.

(1) Set the 7 byte area of 0FFF9h to 0FFFFh to INT.

(2) Execute the RESET command by use of emulator debugger M3T-PD30.

(3) Set the stack pointer.

(Example)

RESET:

FCLR I

LDC #0480H, SP --> Set the stack pointer

(Stop the program after executing this instruction)

(4) Set the 7 byte area 0FFF9h through 0FFFFh to EXT.

( 14 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT

Note on Operation When Not Executing the User Program:

• With this product, bit 7 of processor mode register 1 (wait bit PM17) is forcibly set to "1" (with wait)

when the user program is not executed (e.g. when the program is stopped or when run-time

debugging is being performed). Therefore, if the external area set to 0 wait is accessed by other than

the user program (such as debugging operation), one wait is inserted. However, when wait bit

PM17 is referenced by the dump window etc. the value set during user program execution is

displayed.

Note on Making an MCU file:

• To debug an MCU which has any other size of memory (ROM, RAM), be sure to make an MCU

file for it. For details on making an MCU file, see "2.4 (1) Making an MCU File" on page 25. For

memory maps of each MCU, refer to the datasheet of the MCU.

Notes on Maskable Interrupts:

• Even if a user program is not being executed (including when run-time debugging is being

performed), the evaluation MCU keeps running so as to control the emulation probe. Therefore,

timers and other components do not stop running.

If a maskable interrupt is requested when the user program is not being executed (including when

run-time debugging is being performed), the maskable interrupt request cannot be accepted,

because the emulator disables interrupts. The interrupt request is accepted immediately after the

user program execution is started.

• Take note that when the user program is not being executed (including when run-time debugging

is being performed), a peripheral I/O interruption is not accepted.

Notes on Address-Match Interrupt:

• To debug address-match interrupts, set a software breaks or hardware break at the top address of

the address-match interrupt process. If you set a software breaks or hardware break at an address

where an address-match interrupt occurs, the program will run out of control.

• When an address at which an address-match interrupt occurs is executed in one-step mode, the

program stops after executing the first instruction after returning from the address-match interrupt

processing.

Note on BRK Instruction and BRK Interrupt:

• With this emulator system, a BRK interrupt by a BRK instruction is exclusively used for software

break functions. Therefore, you can not use them for your program.

( 15 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT

Notes on Software and Hardware Breaks:

• The software break is a debugging function which breaks a program immediately before the system

executes an instruction at a specified address. The instruction at the preset address will not be

executed.

• The hardware break is a debugging function which breaks a program by setting the detection of an

execution of an instruction at a specified address as a break event. The program will break after the

instruction at the specified address is executed.

• The software break generates BRK interrupts by substituting the proper instruction to the BRK

instruction. Therefore, when referencing the result of a trace in bus mode, "00h" is displayed for

the instruction fetch address where a software break is set, and when referencing in disassemble

mode, "BRK" instruction is displayed.

• It is not possible to use a software break and a hardware break at the same time. If doing so, it may

not operate normally.

• In the area where the MAP setting is EXTERNAL, software breaks cannot be used.

Note on Stop and Wait Modes:

• Do not perform step execution at addresses in the stop or wait mode. It may cause communication

errors.

Note on Watchdog Function:

• The MCU's watchdog timer can be used only while programs are being executed. To use it

otherwise, disable the watchdog timer.

Note on DMA Transfer:

• With this product, the program is stopped with a loop program to a specific address. Therefore, if

a DMA request is generated by a timer or other source while the program is stopped, a DMA transfer

is executed. However, make note of the fact that a DMA transfer while the program is stopped may

not be performed correctly. Also note that the below registers have been changed to generate a

DMA transfer as explained here even when the program is stopped.

DMA0 transfer counter registers TCR0, TCR1 (M16C/62N only)

Note on Pullup Control:

• With this product, ports P0 [7:0] to P5 [7:0] are not pulled up by the pullup control register.

To pull up the ports P0 to P5, apply a resistance to the inside of the emulator. How to apply it, refer

to "3.5 Installing and Removing Pullup Resistors" (page 37).

Note: Ports P6 to P10 are pulled up by the pullup control registers.

Note: Pullup control registers themselves can be read and written into properly.

( 16 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT

Note on Reading Internal Resources of the MCU:

• When the registers that are listed in Table 1.1 are read with an emulator, those results will be the

following (the data in the MCU are not effected).

(1) Results of real-time trace

The data values of the cycles read are not displayed correctly.

(2) Real-time RAM monitor

The data values read are not displayed correctly.

Table 1.1 Resisters and symbols not displayed normally (*1: M16C/62N only)

Resister

Symbol

DMA source pointers 0, 1 (*1)

DMA destination pointers 0, 1 (*1)

DMA transfer counters 0, 1 (*1)

DMA control resisters 0, 1 (*1)

SAR0, SAR1 (*1)

DAR0, DAR1 (*1)

TCR0, TCR1 (*1)

DM0CON, DM1CON (*1)

Note on Protect Register (PRC2):

• Make note of the fact that the protect is not canceled when protect register (PRC2), which enables

writing in the port P9 direction register and the SI/Oi control register, is changed with the below

procedure.

(1) Step execution of the "instruction for setting ("1") PRC2"

(2) Setting the break point from the instruction for setting ("1") PRC2 to when the port P9

direction register and SI/Oi control register are set.

(3) Setting "("1") PRC2" from the dump window or script window

Note on Accessing Address 00000h:

• With M16C/60 Series MCUs, when a maskable interrupt is generated, the interrupt data (interrupt

No. and interrupt request level) stored in address 00000h is read out. Also, the interrupt request bit

is cleared when address 00000h is read out. Consequently, when the address 00000h readout

instruction is executed or when address 00000h is read out in the cause of a program runaway, a

malfunction occurs in that the interrupt is not executed despite the interrupt request, because the

request bit of the highest priority interrupt factor enabled is cleared.

For this malfunction, when the reading out to the address 00000h is generated excluding the

interrupt, the yellow LED lights up to alarm. When this LED lights, there is a possibility of wrong

access to address 00000h, therefore check the program. This LED is turned off by the system reset

switch of the emulator main unit.

( 17 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT

Note on Differences Between the Actual MCU and Emulator:

• Operation of the emulator differs from that of the actual MCU as listed below.

(1) Reset condition

Set the time for starting up (0.2 Vcc to 0.8 Vcc) 1 µs or less.

(2) Initial values of MCU's internal resources at power-on

(3) Internal memories (ROM and RAM) capacities etc.

With this emulator system, regardless of ROM and RAM of the MCU you use, all the areas

other than the SFR area can be read and written into.

(4) Characteristics of ports P0 to P5

Ports P0 to P5 are connected via emulation circuits. The device used for the port emulation

circuit is the IC21 (ALTERA EPF6016QC208-2).

(5) Oscillator circuit

• Make note that in the oscillator circuit where a resonator is connected between pins X^INand

XOUT, oscillation does not occur because a flexible cable, buffer IC and other devices are used

between the evaluation MCU and the target system. It is same for sub-clock oscillators (XCIN

and XCOUT).

• For notes on when using the oscillator circuit on the target system, refer to "3.3 (2) Using

the Oscillator Circuit on the Target System" (page 31).

(6) A-D conversion function

As a flexible cable and other devices are used between the evaluation MCU and the target

system, some characteristics are slightly different from those of the actual MCU.

(7) DBC, single-step and BRK instruction interrupt vector table addresses

As the emulator uses the DBC, single-step and BRK instruction interrupt vector table

addresses, when reading these addresses, the downloaded data cannot be read (see Table 1.2).

Table 1.2 Vector table addresses for the emulator

Vector table addresses

FFFF4h--FFFF7h

FFFECh--FFFEFh

FFFE4h--FFFE7h

Factor of interruption

DBC*¹

Data read

Indefinite

Single-step*¹

BRK instruction

*1 Interruption for the emulator only

(8) Address and status of BHE*

When the internal RAM or ROM area of the MCU is accessed during user program execution,

the actual MCU retains a preceding address and status of BHE*, while this product does not.

(9) Status of a data bus

In stop or wait mode, the actual MCU retains a preceding status of a data bus, while with this

product a data bus is floating.

(10) ALE signal

When the internal RAM or SFR area of the MCU is accessed during user program execution,

with the actual MCU, ALE output is fixed to Low, while this product outputs ALE signal.

( 18 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT

Note on Debugging Operations After Releasing a Reset from the Target:

• Do not execute debugging operations such as setting a software or hardware break, runtime

debugging after releasing a reset from the target system until an interrupt stack pointer (ISP) is set

in the user program.

Note on Emulating External Area:

• To emulate the external area using emulation memory in this product, set 0 wait (8 MHz) or less,

or 1 wait.

( 19 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

MEMO

( 20 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 2. Preparation

This chapter describes the package components, the system configuration and the preparation for using this product for the

first time.

2.1 Package Components................................................................................................................... 22

2.2 Other Tool Products Required for Development......................................................................... 22

2.3 Name of Each Part ....................................................................................................................... 23

(1) System Configuration ........................................................................................................... 23

(2) Inside of the Emulation Pod.................................................................................................. 24

2.4 When Using This Product for the First Time .............................................................................. 25

(1) Making an MCU File ............................................................................................................ 25

(2) Setting the Work Area .......................................................................................................... 25

(3) Downloading Firmware ........................................................................................................ 26

(4) Self-check ............................................................................................................................. 26

( 21 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 2. Preparation

2.1 Package Components

The M3062NT3-RPD-E package consists of the following items. When unpacking, check to see if

your M3062NT3-RPD-E contains all of these items.

Table 2.1 Package components

Item

Quantity

M3062NT3-RPD-E emulation pod main unit

FLX120-RPD flexible cable for connecting PC4701

M3T-F160T3-PRB converter board for M3T-FLX160C (preinstalled)

M30800T-PTC converter board for 100-pin 0.65-mm-pitch QFP

IC61-1004-051 100-pin 0.65-mm-pitch LCC socket (made by Yamaichi Electronics Co., Ltd.)

OSC-3 16 MHz oscillator circuit board for main clock (preinstalled)

OSC-2 oscillator circuit board for main clock (bare board)

Resistor arrays for pulling up ports P0 to P5 (51 kΩ)

Hardware tool user registration FAX sheet

Hardware tool user registration FAX sheet (Japanese)

M3062NT3-RPD-E User's Manual (This manual)

M3062NT3-RPD-E User's Manual (Japanese)

* Please keep the M3062NT3-RPD-E's packing box and cushion material in your place for reuse

at a later time when sending your product for repair or other purposes. Always use these packing

box and cushion material when transporting this product.

* If any of these items are missing or found faulty, please contact your local distributor.

* If there is any question or doubt about the packaged product, contact your local distributor.

* For purchasing the IC61-1004-051 or for technical information, contact Yamaichi Electronics

Co., Ltd.

2.2 Other Tool Products Required for Development

To bring forward programs development on an M16C/62 Group M16C/62N and M16C/30 Group

M16C/30L, the products listed below are necessary in addition to those contained package above. Get

them separately.

Table 2.2 Other tool products

Emulator main unit

Emulator debugger

Converter board

PC4701 (excluding PC4701L and PC4700L)

M3T-PD30

For 80-pin 0.65-mm-pitch QFP (80P6S-A):

M3T-100LCC-DMS + M3T-FLX-DCT613 + M3T-FLX80QSB

M3T-100LCC-DMS + M3T-FLX-DCT613 + M3T-DIRECT80S

For 100-pin 0.65-mm-pitch QFP (100P6S-A):

M3T-100LCC-DMS + M3T-DIRECT100S

M3T-100LCC-DMS + M3T-DUMMY100S

M3T-100LCC-DMS + M3T-FLX-100NRB

For 100-pin 0.5-mm-pitch LQFP (100P6Q-A):

M3T-F160-100NSD

M3T-100LCC-QSD

M3T-100LCC-DMS + M3T-FLX-100NSD

For 100-pin 0.4-mm-pitch TQFP (100PFB-A):

M3T-F160-100NSE

Required according to the foot pattern of the target system (see "3.8

Connecting the Target System" on page 41)

* To purchase these products, contact your local distributor.

( 22 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

2.3 Name of Each Part

(1) System Configuration

Emulator debugger

Interface cable

Host machine

(2) Flexible cable for connecting PC4701

(1) Emulation pod main unit

Emulator main unit

(3) Flexible cable for connecting target system

(4) Pitch converter board for connecting target system

Figure 2.1 System configuration

(1) to (4) in Figure 2.1 are included with this product package.

(1) Emulation pod main unit M3062NT3-RPD-E

This emulation pod contains an evaluation MCU, emulation memory and circuits to feature the

debug functions.

(2) Flexible cable FLX120-RPD

This is a 120-conductor flexible cable for connecting the PC4701 emulator and the emulation pod.

(3) Flexible cable M3T-FLX160C

This is a 160-conductor flexible cable for connecting the emulation pod and the target system.

(4) Pitch converter board

This is a pitch converter board for connecting to the target system. For details, refer to "3.8

Connecting the Target System" (page 41).

( 23 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

(2) Inside of the Emulation Pod

(1) MCU-dependent board 1

(4) Oscillator circuit board

(2) MCU-dependent Board 2

(3) Common board

Figure 2.2 Internal view of the emulation pod

(1) MCU-dependent board 1

This is a board for port emulation.

(2) MCU-dependent board 2

This is a board with the evaluation MCU.

(3) Common board

This is a board controlling the interface with the PC4701 and evaluation MCU.

(4) Oscillator circuit board

This is a board with an oscillator module. You can change the operating frequency by replacing

it with other oscillator circuit board included with this product package.

( 24 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

2.4 When Using This Product for the First Time

(1) Making an MCU File

It is necessary to make an MCU file to use this product with the emulator debugger M3T-PD30.

According to the MCU you use, change the contents of an MCU file. Make an MCU file following

the description below using a text editor and store it in the "mcufile" folder in the directory where the

emulator debugger is installed.

An MCU file contains information such as, SFR area, internal RAM area, internal ROM area,

firmware file name. The contents of the MCU file when using the M30624FGNFP (20KB RAM,

256KB ROM) are as follows:

3FF

400

53FF

C0000

FFFFF

M30620P

: SFR area

: Internal RAM

: Internal ROM

Start address

End address

Start address

End address

Start address

End address

: Name of firmware (Do not change.)

: Expansion No. M3T-PD30 V.4.00 or later required (Do not change.)

When using this product in microprocessor mode, set the internal ROM area as follows.

00000

00001

: Internal ROM

Start address

End address

(2) Setting the Work Area

With this product, the emulator uses 32 bytes as a work area in emulation memory. Therefore,

according to the memory mapping of the MCU you use, specify the work area addresses.

In single-chip mode, set the work area address at 10000h.

In memory expansion or microprocessor mode, the areas listed below cannot be used as a work area,

specify a work area other than the areas listed below. And the top address of the work area should

be an even-numbered address.

(1) SFR area (0000h--003FFh)

(2) External area of multiplex bus setting

(3) Stack area used by the emulator for reset command execution (0FFF9h--0FFFFh)

The area used as a work area (32 bytes) is specified in the F/W and Work Area tab of the INIT dialog

box of the emulator debugger M3T-PD30. And set the work area as MAP=INT.

( 25 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

(3) Downloading Firmware

The download procedure is given in Figure 2.3. Before attempting to download the firmware, check

that the emulator is connected to the host machine.

See "3.7 Connecting the PC4701"

(page 39).

Connect the PC4701 and this product.

Within 2 seconds of turning the power ON, press the

system reset switch of the PC4701 and check it is in

maintenance mode.

See "4.2 Downloading Firmware"

(page 56).

Download the firmware using the emulator debugger.

End the emulator debugger and shut the power of the

PC4701 OFF.

Figure 2.3 Firmware download procedure

(4) Self-check

To confirm that your emulation pod works properly, execute the self-check after downloading the

firmware. The self-check procedure is given in Figure 2.4.

Within 2 seconds of turning the power ON, press the

system reset switch of the PC4701 and check it is in

maintenance mode.

Push the system reset switch of the PC4701 again to start

See "4.3 Self-check" (page 57).

the self-check.

After about 40 seconds, check that the self-check is

complete normally and shut off the PC4701.

Figure 2.4 Self-check procedure

( 26 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 3. Setting Up

This chapter describes switch settings required for using this product and how to connect this product to the PC4701 and

the target system.

3.1 Removing and Closing the Upper Cover..................................................................................... 28

3.2 Each Setting ................................................................................................................................. 29

3.3 Selecting Clock Supply and Replacing Oscillator Circuit Boards .............................................. 30

(1) Clock Supply to the MCU .................................................................................................... 30

(2) Using the Oscillator Circuit on the Target System ............................................................... 31

(3) Changing the Internal Oscillator Circuit of the Emulation Pod............................................ 32

(4) Replacing Oscillator Circuit Boards ..................................................................................... 33

3.4 Switch Settings ............................................................................................................................ 34

(1) Toggle Switches SW1 to SW5 on the M30620T3-PRT Board (MCU-dependent 1)........... 34

(2) Jumper Switches JP1 and JP2 on the M30620T3-PRT Board (MCU-dependent 1) ............ 36

3.5 Installing and Removing Pullup Resistors .................................................................................. 37

3.6 A-D Conversion Bypass Capacitors ............................................................................................ 38

3.7 Connecting the PC4701 ............................................................................................................... 39

(1) Connecting the Cable to the PC4701 .................................................................................... 39

(2) Connecting the Cable to the Emulation Pod ......................................................................... 40

3.8 Connecting the Target System..................................................................................................... 41

(1) Connecting to a 100-pin LCC Socket ................................................................................... 42

(2) Connecting to an 80-pin 0.65-mm-pitch Foot Pattern (Part 1) ............................................. 43

(3) Connecting to an 80-pin 0.65-mm-pitch Foot Pattern (Part 2) ............................................. 44

(4) Connecting to a 100-pin 0.65-mm-pitch Foot Pattern (Part 1) ............................................. 45

(5) Connecting to a 100-pin 0.65-mm-pitch Foot Pattern (Part 2) ............................................. 46

(6) Connecting to a 100-pin 0.65-mm-pitch Foot Pattern (Part 3) ............................................. 47

(7) Connecting to a 100-pin 0.5-mm-pitch Foot Pattern (Part 1) ............................................... 48

(8) Connecting to a 100-pin 0.5-mm-pitch Foot Pattern (Part 2) ............................................... 49

(9) Connecting to a 100-pin 0.5-mm-pitch Foot Pattern (Part 3) ............................................... 50

(10) Connecting to a 100-pin 0.4-mm-pitch Foot Pattern .......................................................... 51

( 27 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 3. Setting Up

To use this emulation pod with your target system, it is necessary to set as follows. Set the following

after removing the upper cover.

• Input frequency

• Switches

• Pullup resistors

• A-D conversion bypass capacitor

3.1 Removing and Closing the Upper Cover

(1) To open the upper cover, remove the four screws of both sides of this product and lift off the upper

cover (see Figure 3.1).

(2) To close the upper cover, attach the upper cover and secure the four screws of both sides of this

product.

Figure 3.1 Removing the upper cover

CAUTION

When Removing and Closing the Upper Cover:

• Always shut OFF power before opening the upper cover to change the switch

settings.

• Do not touch the connector pins of the PC4701 and the target MCU connector pins.

Static electricity may damage the internal circuits.

( 28 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

3.2 Each Setting

Figure 3.2 shows the positions of the following parts.

(1) Oscillator circuit board

(2) Switches

(3) Pullup resistors

(4) A-D conversion bypass capacitor

M30620T3-RPDC board (common)

MCU-dependent board 1

(M30620T3-PRT board)

MCU-dependent board 2

(M3062NT3-PRTM board)

(1) Oscillator circuit board

(3) Socket for installing pullup resistors

(3) Switches

Figure 3.2 Positions of each part

( 29 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

3.3 Selecting Clock Supply and Replacing Oscillator Circuit Boards

(1) Clock Supply to the MCU

There are two ways to supply a clock to the MCU, using the oscillator circuit of the emulation pod

or using the oscillator circuit on the target system. Table 3.1 lists the factory-settings of each clock

supply. The clock supply can be set in the Init dialog box when starting up the emulator debugger or

inputting CLK command on the script window.

Table 3.1 Clock supply to the MCU

Clock

Description

Display of emulator debugger Default setting

Internal oscillator circuit of emulation pod

(OSC-3: 16.0 MHz)

Internal

External

Internal

External

Yes

X^IN-XOUT

Target system

Internal oscillator circuit of emulation pod

(32.768 kHz)

XCIN-XCOUT

Target system

Yes

IMPORTANT

Note on Changing the Clock Supply:

• For pins XCIN-XCOUT, it is necessary to set the switches in the emulation pod. For

details, refer to "3.4 Switch Settings" (page 34).

( 30 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

(2) Using the Oscillator Circuit on the Target System

To operate this product with an external clock, construct the oscillator circuit as shown in Figure 3.3

in the target system and input the oscillator output at 50% duty (within the operating range of the

evaluation MCU) into pin XIN. And pin XOUT should be open.

To use the external clock on the target system, set in the Init dialog box of the emulator debugger or

by the CLK command on the script window. (For details, refer to the emulator debugger user's

manual.)

Figure 3.3 External oscillator circuit

Make note that in the oscillator circuit shown in Figure 3.4 where a resonator is connected between

pins XIN and XOUT, oscillation does not occur because a converter board and other devices are used

between the evaluation MCU and the target system. It is same for sub-clock oscillator circuits (XCIN

and XCOUT).

Figure 3.4 Circuit in which oscillation does not occur (same for XCIN-XCOUT)

( 31 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

(3) Changing the Internal Oscillator Circuit of the Emulation Pod

An oscillator circuit board for 16.0 MHz (OSC-3) is mounted on this product. To use the emulation

pod at a frequency other than 16.0 MHz, build the desired oscillator circuit on the included OSC-2

oscillator circuit board (bare board) and replace the board installed in the emulation pod when shipped

from the factory.

Figure 3.5 shows a view of the OSC-2 oscillator circuit board (bare board) and where connector pins

are located. Figure 3.6 shows the circuitry of the OSC-2 oscillator circuit board (bare board). Use the

number of oscillator circuits recommended by the oscillator manufacturer.

J1-4: GND

J1-3: Oscillator output

J1-2: GND

J1-1: Vcc

Figure 3.5 External view of the OSC-2 oscillator circuit board and its connector pin positions

IC1

CLK

J1-3

J1-1

Vcc

X1 ,X2

IC1

J1-2

J1-4

GND

IC1

* X1: 5.08-mm-pitch 2-pin oscillator

* X2: 2.54-mm-pitch 2-pin oscillator

* X3: 2.54-mm-pitch 3-pin oscillator

IC1: Inverter (Unbuffer)

Figure 3.6 Circuits of the OSC-2 oscillator circuit bare board

( 32 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

(4) Replacing Oscillator Circuit Boards

Figure 3.7 shows how to replace the oscillator circuit boards. For the position of the oscillator circuit

board, see Figure 3.2.

(1) Unscrew the screw securing the oscillator circuit board.

(2) Lift off the oscillator circuit board.

(3) Insert the J1 connector of a new oscillator circuit board to

the connector of the main board.

(4) Secure the new oscillator circuit board with the screw.

Figure 3.7 Replacing oscillator circuit boards

( 33 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

3.4 Switch Settings

Here follows explanations of the switches of the M3062NT3-RPD-E.

Tables 3.2 and 3.3 list how to set toggle switches SW1 to SW5 of the M30620T3-PRT board (MCU-

dependent 1), Table 3.4 lists how to set jumper switches JP1 and JP2.

(1) Toggle Switches SW1 to SW5 on the M30620T3-PRT Board (MCU-dependent 1)

Table 3.2 Switch settings of the M3062NT3-RPD-E (1/3)

Signal

Switch

Setting

Description

SW1 BYTE

Sets pin BYTE of the MCU to "L" when the target

system is unconnected.

Pulls down pin BYTE of the MCU with a resistance

of 33 kΩ.

(Factory-setting)

SW1 BYTE

Use this setting when the target system is

connected.

BYTE

SW1

Does not pull up/down pin BYTE of the MCU.

(Inputs the level of the target system to pin BYTE

of the MCU.)

SW1 BYTE

Sets pin BYTE of the MCU to "H" when the target

system is unconnected.

Pulls up pin BYTE of the MCU with a resistance of

33 kΩ.

SW2

Sets pin CNVss of the MCU to "L" when the target

system is unconnected.

Pulls down pin CNVss of the MCU with a resistance

of 1 kΩ.

(Factory-setting)

SW2

Use this setting when the target system is

connected.

SW2

CNVss

Does not pull up/down pin CNVss of the MCU.

(Inputs the level of the target system to pin CNVss

of the MCU.)

SW2

Sets pin CNVss of the MCU to "H" when the target

system is unconnected.

Pulls up pin CNVss of the MCU with a resistance

of 1 kΩ.

( 34 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

Table 3.3 Switch settings of the M3062NT3-RPD-E (2/3)

Signal

Switch

Setting

Description

SW3

Does not connect pin Xout of the MCU to the target

system.

(Factory-setting)

SW3

Xout

SW3

Connects pin Xout of the MCU to the target system.

Connects pin P86/Xcout of the MCU to the target

system to use it as port P86 or Xcout.

SW4

(Factory-setting)

P86/Xcout

SW4

Does not connect pin P86/Xcout of the MCU to the

target system.

SW4

Uses pin P87/Xcin of the MCU as port P87.

Uses pin P87/Xcin of the MCU as Xcin.

SW5

(Factory-setting)

P87/Xcin

SW5

CAUTION

Note on Switch Settings:

• Always shut OFF power before changing switch settings.

IMPORTANT

Note on BYTE and CNVss Switch Settings:

• Switch settings of the BYTE and CNVss are for debugging without the target system

connected.

( 35 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

(2) Jumper Switches JP1 and JP2 on the M30620T3-PRT Board (MCU-dependent 1)

Table 3.4 Switch settings of the M3062NT3-RPD-E (3/3)

Signal

Switch

Setting

Description

Use this setting when not using the memory

space expansion mode.

(Factory-setting)

A18_SEL

JP1

Use this setting when using the memory

space expansion mode.

(Factory-setting)

Use this setting.

VDDI0

JP2

Do not use this setting.

CAUTION

Note on Switch Settings:

• Always shut OFF power before changing switch settings.

( 36 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

3.5 Installing and Removing Pullup Resistors

In this product, you cannot control pullup for ports P0 to P5 by pullup control registers (pullup control

Mounting a pullup resistor inside this product allows pullup control. Mount the 51kΩ resistor array

supplied with this product to the port for which pullup control is required. For the mounting location,

refer to Figure 3.8 below.

VCC2

P00

P01

P02

P03

P04

P05

P06

P07

VCC2

P30

P31

P32

P33

P34

P35

P36

P37

VCC2

P50

P51

P52

P53

P54

P55

P56

P57

VCC2

P40

VCC2

P20

P10

P11

P41

P21

P42

P22

P12

P13

P14

P15

P16

P17

P43

P44

P45

P46

P47

P23

P24

P25

P26

P27

Figure 3.8 Position for mounting pullup resistors

CAUTION

Note on Installing and Removing Pullup Resistors:

• Always shut OFF power before installing or removing pullup resistors. Otherwise,

the internal circuits may be damaged.

• Install pullup resistors properly. Otherwise, the emulation pod will be damaged.

( 37 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

3.6 A-D Conversion Bypass Capacitors

The M3062NT3-RPD-E has the M3062PT3-PRTM board which has a foot pattern for installing A-

D conversion bypass capacitors near the MCU and premounted 0.1µF capacitors. Mount suitable

bypass capacitors as occasion demands. Figure 3.2 shows where they are installed and Figure 3.9

shows their connection diagrams.

AVcc - AVss bypass capacitor

AVss

AVcc

VREF - AVss bypass capacitor

AVss

VREF

Figure 3.9 Foot patterns of A-D conversion bypass capacitor

IMPORTANT

Note on the A-D Converter Function:

• Because a flexible cable and other devices are used between the evaluation MCU and

the target system, the A-D converter operates differently from that of the actual

MCU. Make the final evaluation of the A-D converter with the actual MCU.

( 38 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

3.7 Connecting the PC4701

To connect the emulation pod to the PC4701, use the FLX120-RPD 120-pin flexible cable included

with this product package. Connect the PC4701 side connector of FLX120-RPD to the cable

connector of the PC4701, then secure with screws the FLX120-RPD.

(1) Connecting the Cable to the PC4701

Figure 3.10 shows how to connect the PC4701 and FLX120-RPD

Emulator main unit

PC4701 side connector of FLX120-RPD

"UPSIDE" should face up.

Secure this screw.

Figure 3.10 Connecting the cable to the PC4701

CAUTION

Notes on Connecting the Cable:

• Always shut OFF power before connecting the cable. Otherwise, the internal circuits

may be damaged.

• To connect the FLX120-RPD, be sure to hold the both sides of the PC4701 side

connector horizontally with the "UPSIDE" facing up.

IMPORTANT

Note on Securing the Screws:

• After connecting the cable to the emulator main unit PC4701, be sure to secure the

screws mounted in both sides of the connector.

( 39 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

(2) Connecting the Cable to the Emulation Pod

Figure 3.11 shows how to connect the FLX120-RPD and the emulation pod.

Emulation pod

FLX120-RPD (Secure with the screws)

Figure 3.11 Connecting the cable to the emulation pod

CAUTION

When Connecting the Cable:

• Always shut OFF power before connecting the cable. Otherwise, the internal circuits

may be damaged.

IMPORTANT

Note on Securing the Screws:

• After connecting the emulation pod and the FLX120-RPD, be sure to secure the

screws mounted in both sides of the connector cover.

( 40 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

3.8 Connecting the Target System

There are several ways available to connect the emulation pod to target systems as shown in Figure 3.12.

Emulation pod probe

100-pin

80-pin

0.5-mm-pitch

0.4-mm-pitch

0.65-mm-pitch

M30800T-PTC

(included)

M30800T-PTC

(included)

M30800T-PTC

(included)

M3T-100LCC-DMS

(not included)

M3T-100LCC-DMS

(not included)

M3T-100LCC-DMS

(not included)

M3T-FLX-DCT613

(not included)

M3T-FLX100-T

(not included)

M3T-FLX100-R

(not included)

M3T-FLX100-T

(not included)

M3T-FLX100-R

(not included)

M3T-DIRECT80S

80-pin QFP

(not included)

M3T-FLX-80QSB

80-pin QFP

(not included)

LCC socket

100-pin LCC

(included)

M3T-DIRECT100S

100-pin QFP

(not included)

M3T-DUMMY100S

100-pin QFP

(not included)

M3T-FLX-100NRB

100-pin QFP

(not included)

M3T-F160-100NSD

100-pin LQFP

(not included)

M3T-100LCC-QSD

100-pin LQFP

(not included)

M3T-FLX-100NSD

100-pin LQFP

(not included)

M3T-F160-100NSE

100-pin TQFP

(not included)

: No. 1 pin

*1: These three products are in one package.

Figure 3.12 Connecting the target system

CAUTION

Notes on Connecting the Target System:

• Take care not to attach the converter board in a wrong direction. It may cause a fatal

damage to the emulation pod.

( 41 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

(1) Connecting to a 100-pin LCC Socket

To connect the M30800T-PTC (included) to the 100-pin LCC socket (IC61-1004-051 by Yamaichi

Electronics Co., Ltd.) on the target system, following the procedure below.

(1) Attach the CN2 side of the M30800T-PTC to the tip (CN2 side) of the pitch converter board

connected to the emulation pod probe.

(2) Attach the M30800T-PTC to the 100-pin LCC socket.

Tip of emulation pod probe

Tip of pitch converter board

CN2 side

(1)

M30800T-PTC

100-pin LCC socket

(2)

No. 1 pin

Target system

Figure 3.13 Connecting to a 100-pin LCC socket

CAUTION

Notes on Connecting the Target System:

• Take care not to attach the converter board in a wrong direction. It may cause a fatal

damage to the emulation pod.

• The connectors of the M30800T-PTC are guaranteed for only 50 insertion/removal

iterations.

• The connector of the IC61-1004-51 is guaranteed for only 20 insertion/removal

iterations.

• For purchasing the IC61-1004-51 or for technical information, contact Yamaichi

Electronics Co., Ltd. (http://www.yamaichi.co.jp/e/index.shtml)

( 42 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

(2) Connecting to an 80-pin 0.65-mm-pitch Foot Pattern (Part 1)

Here follows how to connect the emulation pod probe to an 80-pin 0.65-mm-pitch foot pattern on the

target system with the M3T-DIRECT80S (not included). For details on the M3T-FLX-DCT613 (not

included) and M3T-DIRECT80S (not included), refer to each user's manual.

(1) Mount the M3T-DIRECT80S to the target system.

(2) Attach the CN2 side of the M30800T-PTC to the tip (CN2 side) of the pitch converter board

connected to the emulation pod probe.

(3) Attach the M30800T-PTC to the M3T-100LCC-DMS.

(4) Attach the M3T-FLX-DCT613 to the M3T-100LCC-DMS.

(5) Attach the M3T-FLX-DCT613 to the M3T-DIRECT80S.

Tip of emulation pod probe

Tip of pitch converter board

CN2 side

(2)

M30800T-PTC

M3T-100LCC-DMS (not included)

M3T-FLX-DCT613 (not included)

(3)

(4)

(5)

(1)

M3T-DIRECT80S (not included)

80-pin 0.65-mm-pitch (80P6S-A) foot patern

No. 1 pin

Target system

Figure 3.14 Connecting to an 80-pin 0.65-mm-pitch foot pattern (part 1)

CAUTION

Notes on Connecting the Target System:

• Take care not to attach the converter board in a wrong direction. It may cause a fatal

damage to the emulation pod.

• The connectors of the M30800T-PTC are guaranteed for only 50 insertion/removal

iterations.

• The connectors of the M3T-100LCC-DMS, M3T-FLX-DCT613 and M3T-

DIRECT80S are guaranteed for only 20 insertion/removal iterations.

( 43 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

(3) Connecting to an 80-pin 0.65-mm-pitch Foot Pattern (Part 2)

Here follows how to connect the emulation pod probe to an 80-pin 0.65-mm-pitch foot pattern on the

target system with the M3T-FLX-80QSB (not included). For details on the M3T-FLX-DCT613 (not

included) and M3T-FLX-80QSB (not included), refer to each user's manual.

(1) Mount the TQPACK80SB to the target system.

(2) Attach the TQSOCKET80SBG to the TQPACK80SB.

(3) Attach the M3T-FLX-80QSB to the TQSOCKET80SBG.

(4) Attach the CN2 side of the M30800T-PTC to the tip (CN2 side) of the pitch converter board

connected to the emulation pod probe.

(5) Attach the M30800T-PTC to the M3T-100LCC-DMS.

(6) Attach the M3T-FLX-DCT613 to the M3T-100LCC-DMS.

(7) Attach the M3T-FLX-DCT613 to the M3T-FLX-80QSB.

Tip of emulation pod probe

Tip of pitch converter board

CN2 side

(4)

M30800T-PTC

M3T-100LCC-DMS (not included)

(5)

M3T-FLX-DCT613 (not included)

(6)

M3T-FLX-80QSB (not included)

(7)

(3)

(2)

TQSOCKET80SBG

TQPACK80SB

* There three parts are in one package.

80-pin 0.65-mm-pitch (80P6S-A) foot pattern

(1)

No. 1 pin

Target system

Figure 3.15 Connecting to an 80-pin 0.65-mm-pitch foot pattern (part 2)

CAUTION

Notes on Connecting the Target System:

• Take care not to attach the converter board in a wrong direction. It may cause a fatal

damage to the emulation pod.

• The connectors of the M30800T-PTC are guaranteed for only 50 insertion/removal

iterations.

• The connectors of the M3T-100LCC-DMS, M3T-FLX-DCT613 and M3T-FLX-

80QSB are guaranteed for only 20 insertion/removal iterations.

( 44 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

(4) Connecting to a 100-pin 0.65-mm-pitch Foot Pattern (Part 1)

Here follows how to connect the emulation pod probe to a 100-pin 0.65-mm-pitch foot pattern on the

target system with the M3T-DIRECT100S (not included). For details on the M3T-100LCC-DMS

(not included) and M3T-DIRECT100S (not included), refer to each user's manual.

(1) Mount the M3T-DIRECT100S to the target system.

(2) Attach the M3T-100LCC-DMS to the M3T-DIRECT100S.

(3) Attach the CN2 side of the M30800T-PTC to the tip (CN2 side) of the pitch converter board

connected to the emulation pod probe.

(4) Attach the M30800T-PTC to the M3T-100LCC-DMS.

Tip of emulation pod probe

Tip of pitch converter board

CN2 side

(3)

M30800T-PTC

M3T-100LCC-DMS (not included)

(4)

(2)

(1)

M3T-DIRECT100S (not included)

6S-A) foot pattern

100-pin 0.65-mm-pitch (100P

No. 1 pin

Target system

Figure 3.16 Connecting to a 100-pin 0.65-mm-pitch foot pattern (part 1)

CAUTION

Notes on Connecting the Target System:

• Take care not to attach the converter board in a wrong direction. It may cause a fatal

damage to the emulation pod.

• The connectors of the M30800T-PTC are guaranteed for only 50 insertion/removal

iterations.

• The connectors of the M3T-100LCC-DMS and M3T-DIRECT100S are guaranteed

for only 20 insertion/removal iterations.

( 45 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

(5) Connecting to a 100-pin 0.65-mm-pitch Foot Pattern (Part 2)

Here follows how to connect the emulation pod probe to a 100-pin 0.65-mm-pitch foot pattern on the

target system with the M3T-DUMMY100S (not included). For details on the M3T-100LCC-DMS

(not included) and M3T-DUMMY100S (not included), refer to each user's manual.

(1) Mount the M3T-DUMMY100S to the target system.

(2) Attach the M3T-100LCC-DMS to the M3T-DUMMY100S.

(3) Attach the CN2 side of the M30800T-PTC to the tip (CN2 side) of the pitch converter board

connected to the emulation pod probe.

(4) Attach the M30800T-PTC to the M3T-100LCC-DMS.

Tip of emulation pod probe

Tip of pitch converter board

CN2 side

(3)

M30800T-PTC

M3T-100LCC-DMS (not included)

(4)

(2)

Onboard evaluation

M3T-DUMMY100S

(not included)

Flash version MCU etc.

100-pin 0.65-mm-pitch (100P6S-A) foot pattern

(1)

No. 1 pin

Target system

Figure 3.17 Connecting to a 100-pin 0.65-mm-pitch foot pattern (part 2)

CAUTION

Notes on Connecting the Target System:

• Take care not to attach the converter board in a wrong direction. It may cause a fatal

damage to the emulation pod.

• The connectors of the M30800T-PTC are guaranteed for only 50 insertion/removal

iterations.

• The connectors of the M3T-100LCC-DMS and M3T-DUMMY100S are guaran-

teed for only 20 insertion/removal iterations.

( 46 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

(6) Connecting to a 100-pin 0.65-mm-pitch Foot Pattern (Part 3)

Here follows how to connect the emulation pod probe to a 100-pin 0.65-mm-pitch foot pattern on the

target system with the M3T-FLX-100NRB (not included). For details on the M3T-100LCC-DMS

(not included) and M3T-FLX-100NRB (not included), refer to each user's manual.

(1) Mount the NQPACK100RB to the target system.

(2) Attach the YQPACK100RB to the NQPACK100RB and secure it with included YQ-

GUIDE's.

(3) Attach the M3T-FLX-100NRB to the YQPACK100RB.

(4) Attach the M3T-100LCC-DMS to the M3T-FLX-100NRB.

(5) Attach the CN2 side of the M30800T-PTC to the tip (CN2 side) of the pitch converter board

connected to the emulation pod probe.

(6) Attach the M30800T-PTC to the M3T-100LCC-DMS.

Tip of emulation pod probe

Tip of pitch converter bpard

CN2 side

(5)

M30800T-PTC

M3T-100LCC-DMS (not included)

(6)

(4)

M3T-FLX-100NRB (not included)

Onboard evaluation

(3) YQ-GUIDE's (x4)

YQPACK100RB

HQPACK100RB168

(not included)

These four parts are in one package.

NQPACK100RB Flash version MCU etc.

(2)

(1)

These corners are not round.

100-pin 0.65-mm-pitch (100P6S-A) foot pattern

No. 1 pin

Target system

Figure 3.18 Connecting to a 100-pin 0.65-mm-pitch foot pattern (part 3)

CAUTION

Notes on Connecting the Target System:

• Take care not to attach the converter board in a wrong direction. It may cause a fatal

damage to the emulation pod.

• The connectors of the M30800T-PTC are guaranteed for only 50 insertion/removal

iterations.

• The connectors of the M3T-100LCC-DMS and M3T-FLX-100NRB are guaranteed

for only 20 insertion/removal iterations.

( 47 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

(7) Connecting to a 100-pin 0.5-mm-pitch Foot Pattern (Part 1)

Here follows how to connect the emulation pod probe to a 100-pin 0.5-mm-pitch foot pattern on the

target system with the M3T-F160-100NSD (not included). For details on the M3T-F160-100NSD

(not included), refer to its user's manual.

(1) Mount the NQPACK100SD included with the M3T-F160-100NSD to the target system.

(2) Attach the YQPACK100SD included with the M3T-F160-100NSD to the NQPACK100SD,

and secure it with YQ-GUIDE's.

(3) Attach the CN2 side of the M3T-F160-100NSD to the tip (CN2 side) of the pitch converter

board connected to the emulation pod probe.

(4) Attach the M3T-F160-100NSD to the YQPACK100SD.

Tip of emulation pod probe

Tip of pitch converter board

CN2 side

(3)

M3T-F160-100NSD (not included)

Onboard evaluation

(4)

HQPACK100SD

YQ-GUIDE's (x4)

YQPACK100SD

(not included)

These four parts are in one package.

(2)

(1)

NQPACK100SD

Flash version MCU etc.

These corners are not round.

100-pin 0.5-mm-pitch (100P6Q-A) foot pattern

No. 1 pin

Target system

Figure 3.19 Connecting to a 100-pin 0.5-mm-pitch foot pattern (part 1)

CAUTION

Notes on Connecting the Target System:

• Take care not to attach the converter board in a wrong direction. It may cause a fatal

damage to the emulation pod.

• The connector of the M3T-F160-100NSD is guaranteed for only 50 insertion/

removal iterations.

( 48 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

(8) Connecting to a 100-pin 0.5-mm-pitch Foot Pattern (Part 2)

Here follows how to connect the emulation pod probe to a 100-pin 0.5-mm-pitch foot pattern on the

target system with the M3T-100LCC-QSD (not included). For details on the M3T-100LCC-QSD

(not included), refer to its user's manual.

(1) Mount the TQPACK100SD to the target system.

(2) Attach the TQSOCKET100SDG to the TQPACK100SD.

(3) Attach the M3T-100LCC-QSD to the TQSOCKET100SDG.

(4) Attach the CN2 side of the M30800T-PTC to the tip (CN2 side) of the pitch converter board

connected to the emulation pod probe.

(5) Attach the M30800T-PTC to the M3T-100LCC-QSD.

Tip of emulation pod probe

Tip of pitch converter board

CN2 side

(4)

M30800T-PTC

(5)

M3T-100LCC-QSD (not included)

(3)

(2)

(1)

TQSOCKET100SDG

TQPACK100SD

These three parts are in one package.

100-pin 0.5-mm-pitch (100P6Q-A) foot pattern

No. 1 pin

Target system

Figure 3.20 Connecting to a 100-pin 0.5-mm-pitch foot pattern (part 2)

CAUTION

Notes on Connecting the Target System:

• Take care not to attach the converter board in a wrong direction. It may cause a fatal

damage to the emulation pod.

• The connectors of the M30800T-PTC are guaranteed for only 50 insertion/removal

iterations.

• The connector of the M3T-100LCC-QSD is guaranteed for only 20 insertion/

removal iterations.

( 49 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

(9) Connecting to a 100-pin 0.5-mm-pitch Foot Pattern (Part 3)

Here follows how to connect the emulation pod probe to a 100-pin 0.5-mm-pitch foot pattern on the

target system with the M3T-FLX-100NSD (not included). For details on the M3T-100LCC-DMS

(not included) and M3T-FLX-100NSD (not included), refer to each user's manual.

(1) Mount the NQPACK100SD to the target system.

(2) Attach the YQPACK100SD included with the M3T-FLX-100NSD to the NQPACK100SD

and secure it with the included YQ-GUIDE's.

(3) Attach the M3T-FLX-100NSD to the YQPACK100SD.

(4) Attach the M3T-100LCC-DMS to the M3T-FLX-100NSD.

(5) Attach the CN2 side of the M30800T-PTC to the tip (CN2 side) of the pitch converter board

connected to the emulation pod probe.

(6) Attach the M30800T-PTC to the M3T-100LCC-DMS.

Tip of emulation pod probe

Tip of pitch converter board

CN2 side

(5)

M30800T-PTC

M3T-100LCC-DMS (not included)

(6)

(4)

M3T-FLX-100NSD (not included)

Onboard evaluation

(3)

HQPACK100SD

YQ-GUIDE's (x4)

(not included)

These four parts are in one package.

YQPACK100SD

NQPACK100SD

Flash version MCU etc.

(2)

These corners are not round.

100-pin 0.5-mm-pitch (100P6Q-A) foot pattern

(1)

No. 1 pin

Target system

Figure 3.21 Connecting to a 100-pin 0.5-mm-pitch foot pattern (part 3)

CAUTION

Notes on Connecting the Target System:

• Take care not to attach the converter board in a wrong direction. It may cause a fatal

damage to the emulation pod.

• The connectors of the M30800T-PTC are guaranteed for only 50 insertion/removal

iterations.

• The connectors of the M3T-100LCC-DMS and M3T-FLX-100NSD are guaranteed

for only 20 insertion/removal iterations.

( 50 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

(10) Connecting to a 100-pin 0.4-mm-pitch Foot Pattern

Here follows how to connect the emulation pod probe to a 100-pin 0.4-mm-pitch foot pattern on the

target system with the M3T-F160-100NSE (not included). For details on the M3T-F160-100NSE

(not included), refer to its user's manual.

(1) Mount the NQPACK100SE included with the M3T-F160-100NSE to the target system.

(2) Attach the YQPACK100SE included with the M3T-F160-100NSE to the NQPACK100SE,

and secure it with YQ-GUIDE's.

(3) Attach the CN2 side of the M3T-F160-100NSE to the tip (CN2 side) of the pitch converter

board connected to the emulation pod probe.

(4) Attach the M3T-F160-100NSE to the YQPACK100SE.

Tip of emulation pod probe

Tip of pitch converter board

CN2 side

(3)

M3T-F160-100NSE (not included)

Onboard evaluation

(4)

HQPACK100SE

(not included)

YQ-GUIDE's (x4)

YQPACK100SE

These four parts are in one package.

NQPACK100SE

(2)

(1)

Flash version MCU etc.

These corners are not round.

100-pin 0.4-mm-pitch (100PFB-A) foot pattern

No. 1 pin

Target system

Figure 3.22 Connecting to a 100-pin 0.4-mm-pitch foot pattern

CAUTION

Notes on Connecting the Target System:

• Take care not to attach the converter board in a wrong direction. It may cause a fatal

damage to the emulation pod.

• The connectors of the M3T-F160-100NSE are guaranteed for only 50 insertion/

removal iterations.

( 51 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

MEMO

( 52 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 4. Usage

This chapter describes from turning on the power of this product to starting up the emulator debugger.

4.1 Turning On the Power ................................................................................................................. 54

(1) Checking Connections of the Emulator System ................................................................... 54

(2) Turning ON/OFF the Power ................................................................................................. 54

(3) LED Display When the PC4701 Starts Up Normally........................................................... 55

4.2 Downloading Firmware ............................................................................................................... 56

(1) When It is Necessary to Download Firmware ...................................................................... 56

(2) Downloading Firmware in Maintenance Mode .................................................................... 56

4.3 Self-check .................................................................................................................................... 57

(1) Self-check Procedure ............................................................................................................ 57

(2) If an Error is Detected in the Self-check............................................................................... 57

( 53 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 4. Usage

4.1 Turning On the Power

(1) Checking Connections of the Emulator System

Before turning the power ON, check the connections of the PC4701, emulation pod, converter board

and target system.

(2) Turning ON/OFF the Power

• Turn on the power of the emulator and target system as simultaneously as possible.

• Turn off the power of the emulator and target system as simultaneously as possible.

• Do not leave either the emulator or target system powered on, because of leakage current the

internal circuits may be damaged.

• When turning on the power again after shutting off the power, wait about 10 seconds.

CAUTION

Notes on Power Supply:

• Pin Vcc of the emulator is connected to the target system to observe the voltage of

the target system. Therefore design your system so that the target system is powered

by an external power supply.

• The voltage of the target system should be within the MCU's specified range.

• Do not change target system power supply voltage after power has been activated.

( 54 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

(3) LED Display When the PC4701 Starts Up Normally

After the emulator starts up, check the status of the LEDs on the front panel to see whether emulation

pod operation is enabled or not. Figure 4.1 shows front panel LED lighting status when the emulator

is turned ON.

•

When this does not light, check the power supply

of the target system

Check that power is supplied to all the power is

supplied to all the terminals.

This does not light when the target system is not

connected.

•

When this lights, check the reset pin of the target

system.

Figure 4.1 LED display when the power turned on

IMPORTANT

Note on Memory Expansion and Microprocessor Modes:

• To use memory expansion or microprocessor mode, be sure to set pins RDY* and

HOLD* so that they are not active at startup. Otherwise the emulator system will not

start up correctly.

Note on the Target Status POWER LED:

• If the MCU has two or more Vcc terminals, the LED does not light unless power is

supplied to all the terminals.

Note on the Target Status CLOCK LED:

• If the LED is not turned on, check the following.

(1) After powering on the PC4701 (before starting up the emulator debugger):

Make sure that the oscillator circuit board is properly installed in the PC4701 and

it is oscillating normally.

(2) After the emulator debugger is started up (after the Init dialog box settings are

complete):

Make sure that the oscillator selected in the Init dialog box is oscillating normally.

( 55 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

4.2 Downloading Firmware

(1) When It is Necessary to Download Firmware

It is necessary to download the firmware in the cases listed below. Normally, the following are

automatically detected when the emulator debugger is started up, and the firmware is downloaded.

(1) When you use this product for the first time

(2) When the emulator debugger or firmware has been upgraded

(3) When you use this product with a PC4701 which was used with another emulation probe before

If you use this product for the first time or have accidentally failed to download the firmware,

redownload the firmware in maintenance mode.

(2) Downloading Firmware in Maintenance Mode

Download the firmware in maintenance mode as explained here following. Figure 4.2 shows LED

display during firmware download. The target system must not be connected when downloading

the firmware.

(1) Within 2 seconds of activating power to the emulator, press the system reset switch on the

emulator front panel to switch the emulator to maintenance mode. Then the system status

SAFE LED will start blinking.

(2) Start up the emulator debugger. When the Init dialog box setup is complete, the dialog which

urges to download the firmware will appear. Download the firmware following messages.

Required time for downloading the firmware depends on the connection of the interface.

• USB and LPT interface ..................... about 20 seconds

• Dedicated parallel interface .............. about 30 seconds

• Serial interface .................................. about 5 minutes

Figure 4.2 Downloading firmware in maintenance mode

IMPORTANT

Note on Downloading Firmware:

• Do not shut OFF power while the firmware is being downloaded. Doing so, the

emulator will not start up properly. If power is shut OFF by mistake, redownload the

firmware in maintenance mode.

( 56 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

4.3 Self-check

(1) Self-check Procedure

To run the self-check of the emulator, do so as explained here below. While the self-check is in

progress, the LEDs will change as shown in Figure 4.4.

(1) Set the switches in the emulation pod to the factory settings as shown in Figure 4.3.

(2) If the target system is connected, disconnect it.

(3) Within 2 seconds of activating power to the emulator, press the system reset switch on the

emulator front panel to switch the emulator to maintenance mode.

(4) Check the SAFE LED starts blinking and then press the system reset switch again.

(5) The self-check will start. If the normal result is displayed in about 40 seconds, the self-check

has terminated normally.

(Factory-setting)

(Factory-setting) (Factory-setting)

(Factory-setting)

(Factory-setting) (Factory-setting)

M30620T3-PRT board

Figure 4.3 Switch settings (factory-settings) for the self-check

(2) If an Error is Detected in the Self-check

If the self-check does not result normally (system status error or target status error in Figure 4.4),

check the following.

• Whether the emulation pod and PC4701 are connected properly

• Whether the proper firmware has been downloaded

• Whether the switch settings of this product are the factory settings (Figure 4.3)

IMPORTANT

Note on Self-check:

• If the self-check does not result normally (excluding target system error), the

emulation pod may be damaged. Then contact your local distributor.

( 57 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

Figure 4.4 Self-check procedure

( 58 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 5. Specifications

This chapter describes specifications of this product.

5.1 Specifications .............................................................................................................................. 60

5.2 Operation Timing in Memory Expansion and Microprocessor Modes ....................................... 61

(1) Separate Bus, No-Wait ......................................................................................................... 61

(2) Separate Bus, With Wait, Accessing External Memory Area .............................................. 63

(3) Multiplex Bus Timing........................................................................................................... 65

(4) Timing Requirements ........................................................................................................... 67

5.3 Connection Diagram.................................................................................................................... 68

5.4 External Dimensions ................................................................................................................... 70

(1) External Dimensions of the Emulation Pod.......................................................................... 70

(2) External Dimensions of the Converter Board M30800T-PTC ............................................. 71

(3) External Dimensions of the Converter Board M3T-F160-100NSD ..................................... 72

(4) External Dimensions of the Converter Board M3T-F160-100NSE ..................................... 72

( 59 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 5. Specifications

5.1 Specifications

Table 5.1 lists the specifications of the M3062NT3-RPD-E.

Table 5.1 Specifications of the M3062NT3-RPD-E

PC4701 (excluding PC4701L and PC4700L)

Emulators

M16C/62 Group M16C/62N and M16C/30 Group M16C/30L

M30620MCN-001FP x2 (for development tool only)

Single-chip mode, Memory expansion mode, Microprocessor mode

1 MB (Max. operating frequency: 16 MHz. no-wait)

2.2 to 3.6 V

Applicable MCU

Evaluation MCU

Usable mode

Emulation memory

Supported voltage

Maximum operating frequency

3.0 to 3.6 V: f(XIN) = 16.0 MHz, no-wait

2.4 to 3.6 V: f(XIN) = 7.0 MHz, no-wait

2.2 to 3.6 V: f(XIN) = 3.5 MHz, no-wait

2.2 to 3.6 V: f(XIN) = 7.0 MHz, 1 wait

X_IN-X_OUT

Internal oscillator circuit board (OSC-3)

Switchable to external oscillator input

Clock supply

XCIN-XCOUT

Internal oscillator circuit board (fixed 32.768 kHz)

Switchable to external oscillator input

2.7 to 5.5 V

Operating voltage

5 to 35°C (no dew)

Operating temperature

Storage temperature

-10 to 60°C (no dew)

Supplied from PC4701

Power supply to emulation pod

100-pin 0.65-mm-pitch LCC socket:

Connection to target system

Refer to "3.8 Connecting the Target

System" (page 41).

(1) M30800T-PTC (included)

+ IC61-1004-051 (included)

80-pin 0.65-mm-pitch QFP (80P6S-A):

(1) M30800T-PTC (included)

+ M3T-100LCC-DMS (not included)

+ M3T-FLX-DCT613 (not included)

+ M3T-FLX-80QSB (not included)

(2) M30800T-PTC (included)

+ M3T-100LCC-DMS (not included)

+ M3T-FLX-DCT613 (not included)

+ M3T-DIRECT80S (not included)

100-pin 0.65-mm-pitch QFP (100P6S-A):

(1) M30800T-PTC (included)

+ M3T-100LCC-DMS (not included)

+ M3T-DIRECT100S (not included)

(2) M30800T-PTC (included)

+ M3T-100LCC-DMS (not included)

+ M3T-DUMMY100S (not included)

(3) M30800T-PTC (included)

+ M3T-100LCC-DMS (not included)

+ M3T-FLX-100NRB (not included)

100-pin 0.5-mm-pitch LQFP (100P6Q-A):

(1) M3T-F160-100NSD (not included)

(2) M30800T-PTC (included)

+ M3T-100LCC-QSD (not included)

(3) M30800T-PTC (included)

+ M3T-100LCC-DMS (not included)

+ M3T-FLX-100NSD (not included)

100-pin 0.4-mm-pitch TQFP (100PFB-A):

(1) M3T-F160-100NSE (not included)

( 60 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

5.2 Operation Timing in Memory Expansion and Microprocessor Modes

(1) Separate Bus, No-Wait

Table 5.2 and Figure 5.1 show the bus timing in memory expansion and microprocessor modes (no-

wait).

Table 5.2 Memory expansion and microprocessor modes (no-wait)

Actual MCU

[ns]

This product

[ns]

Item

Symbol

Min.

Max.

Min.

Max.

td(BCLK-AD)

th(BCLK-AD)

th(RD-AD)

Address output delay time

See left

Address output hold time (BCLK standard)

Address output hold time (RD standard)

Address output hold time (WR standard)

Chip-select output delay time

See left

-4

th(WR-AD)

td(BCLK-CS)

th(BCLK-CS)

td(BCLK-ALE)

th(BCLK-ALE)

td(BCLK-RD)

th(BCLK-RD)

td(BCLK-WR)

th(BCLK-WR)

td(BCLK-DB)

th(BCLK-DB)

td(DB-WR)

See left

Chip-select output hold time (BCLK standard)

ALE signal output delay time

-4

See left

ALE signal output hold time

RD signal output delay time

RD signal output hold time

WR signal output delay time

WR signal output hold time

Data output delay time (BCLK standard)

Data output hold time (BCLK standard)

Data output delay time (WR standard)

Data output hold time (WR standard)

(*1)

See left

th(WR-DB)

*1 Calculated by the following formula according to the frequency of BCLK.

10⁹

td(DB-WR)=

-50 [ns]

f(BCLK)x2

( 61 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

Read

Write

Conditions:

• VCC = 3.3 V

• Input timing voltage: VIL = 0.52 V, VIH = 1.65 V

• Output timing voltage: VOL = 1.65 V, VOH = 1.65 V

Figure 5.1 Memory expansion and microprocessor modes (no-wait)

( 62 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

(2) Separate Bus, With Wait, Accessing External Memory Area

Table 5.3 and Figure 5.2 show the bus timing in memory expansion and microprocessor modes (with

wait, accessing external area).

Table 5.3 Memory expansion and microprocessor modes (with wait, accessing external area)

Actual MCU

[ns]

This product

[ns]

Symbol

Item

Min.

Max.

Min.

Max.

td(BCLK-AD)

th(BCLK-AD)

th(RD-AD)

Address output delay time

See left

Address output hold time (BCLK standard)

Address output hold time (RD standard)

Address output hold time (WR standard)

Chip-select output delay time

See left

-4

th(WR-AD)

td(BCLK-CS)

th(BCLK-CS)

td(BCLK-ALE)

th(BCLK-ALE)

td(BCLK-RD)

th(BCLK-RD)

td(BCLK-WR)

th(BCLK-WR)

td(BCLK-DB)

th(BCLK-DB)

td(DB-WR)

See left

Chip-select output hold time (BCLK standard)

ALE signal output delay time

-4

See left

ALE signal output hold time

RD signal output delay time

RD signal output hold time

WR signal output delay time

WR signal output hold time

Data output delay time (BCLK standard)

Data output hold time (BCLK standard)

Data output delay time (WR standard)

Data output hold time (WR standard)

(*1)

See left

th(WR-DB)

*1 Calculated by the following formula according to the frequency of BCLK.

10⁹

td(DB-WR)=

-50 [ns]

f(BCLK)

( 63 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

Read

Write

Conditions:

• VCC = 3.3 V

• Input timing voltage: VIL = 0.52 V, VIH = 1.65 V

• Output timing voltage: VOL = 1.65 V, VOH = 1.65 V

Figure 5.2 Memory expansion and microprocessor modes (with wait, accessing external area)

( 64 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

(3) Multiplex Bus Timing

Table 5.4 and Figure 5.3 show the bus timing in memory expansion and microprocessor modes (with

wait, accessing external area, using multiplex bus).

Table 5.4 Memory expansion and microprocessor modes (with wait, accessing external area, using multiplex bus)

Actual MCU

[ns]

This product

[ns]

Symbol

Item

Max.

Min.

Max.

Min.

td(BCLK-AD)

th(BCLK-AD)

th(RD-AD)

Address output delay time

See left

Address output hold time (BCLK standard)

Address output hold time (RD standard)

Address output hold time (WR standard)

Chip-select output delay time

See left

(*2)

(*1)

th(WR-AD)

td(BCLK-CS)

th(BCLK-CS)

th(RD-CS)

See left

Chip-select output hold time (BCLK standard)

Chip-select output hold time (RD standard)

Chip-select output hold time (WR standard)

RD signal output delay time

See left

(*2)

(*1)

th(WR-CS)

(*2)

td(BCLK-RD)

th(BCLK-RD)

td(BCLK-WR)

th(BCLK-WR)

td(BCLK-DB)

th(BCLK-DB)

td(DB-WR)

See left

RD signal output hold time

See left

WR signal output delay time

WR signal output hold time

Data output delay time (BCLK standard)

Data output hold time (BCLK standard)

Data output delay time (WR standard)

Data output hold time (WR standard)

ALE output delay time (BCLK standard)

ALE output hold time (BCLK standard)

ALE output delay time (Address standard)

ALE output hold time (Address standard)

After address RD signal output delay time

After address WR signal output delay time

Address output floating start time

See left

(*2)

(*1)

th(WR-DB)

(*2)

td(BCLK-ALE)

th(BCLK-ALE)

td(AD-ALE)

th(ALE-AD)

td(AD-RD)

See left

-4

(*1)

See left

-4

td(AD-WR)

-3

tdz(RD-AD)

*1 Calculated by the following formula accord- *2 Calculated by the following formula accord-

ing to the frequency of BCLK.

10⁹

f(BCLK)x2

th(RD-AD)=

+0 [ns]

10⁹

f(BCLK)x2

10⁹

f(BCLK)x2

10⁹

f(BCLK)x2

10⁹x3

f(BCLK)x2

10⁹

f(BCLK)x2

10⁹

f(BCLK)x2

10⁹

f(BCLK)x2

th(WR-AD)=

th(RD-CS)=

th(WR-CS)=

th(DB-WR)=

th(WR-DB)=

th(AD-ALE)=

th(WR-AD)=

+0 [ns]

-50 [ns]

+0 [ns]

-40 [ns]

-6 [ns]

10⁹

f(BCLK)x2

th(WR-CS)=

th(WR-DB)=

-6 [ns]

10⁹

f(BCLK)x2

-12 [ns]

( 65 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

Read

Write

Conditions:

• VCC = 3.3 V

• Input timing voltage: VIL = 0.52 V, VIH = 1.65 V

• Output timing voltage: VOL = 1.65 V, VOH = 1.65 V

Figure 5.3 Memory expansion and microprocessor modes (with wait, accessing external area, using multiplex bus)

( 66 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

(4) Timing Requirements

Table 5.5 and Figure 5.4 show the timing requirements.

Table 5.5 Timing requirements

Actual MCU

[ns]

This product

[ns]

Symbol

Item

Min.

100

Max.

Min.

Max.

tsu(DB-RD)

Data input setup time

RDY* input setup time

tsu(RDY-BCLK)

tsu(HOLD-BCLK) HOLD* input setup time

115

th(RD-DB)

Data input hold time

RDY* input hold time

HOLD* input hold time

HLDA* output delay time

See left

th(BCLK-RDY)

th(BCLK-HOLD)

td(BCLK-HLDA)

See left

Common to "with wait" and "no-wait" (actual MCU)

Common to "with wait" and "no-wait" (this product)

Note 1. P00 to P52 will be high-impedance status regardless of the input level of pin BYTE and ports

P40 to P43 function selection bit (PM06) of the processor mode register 0.

Note 2. Compared with the actual MCU, this product enters high-impedance state after a 0.5 cycle

delay.

Conditions:

• VCC = 3.3 V

• Input timing voltage: VIL = 0.66 V, VIH = 2.64 V

• Output timing voltage: VOL = 1.65 V, VOH = 1.65 V

Figure 5.4 Timing requirements

( 67 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

5.3 Connection Diagram

Figure 5.5 shows a connection diagram of the M3062NT3-RPD-E. This connection diagram mainly

shows the interface section. The circuits not connected to the target system such as the emulator's

control system are omitted. The signals not shown in Figure 5.5 connect the evaluation MCU and the

target system directly.

Tables 5.6 and 5.7 show IC electric characteristics of this product for reference purposes.

Figure 5.5 Connection diagram

( 68 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

Table 5.6 Electrical characteristics of the 74HC4066

Standard values

Symbol

Item

Condition

Unit

Max.

Min.

Standard

R^ON

RON

IOFF

IIZ

ON resistor

Vcc = 4.5 V

Vcc = 12.0 V

200

Ω

ON resistor difference

Leak current (Off)

±1

µA

Leak current (On, output: open)

Table 5.7 Electrical characteristics of the FPGA

Standard values

Condition

Symbol

Item

Unit

Standard

Min.

2.0

Max.

5.5

VIH

VIL

"H" level input voltage

"L" level input voltage

-0.5

0.8

IOH = -8 mA DC,

Vcc = 1.75 V

2.4

V^OH

"H" level output voltage

"L" level output voltage

IOH = -8 mA DC,

Vcc = 3.00 V

I^OH= -8 mA DC,

Vcc = 4.75 V

0.45

V^OL

I^OH= -8 mA DC,

Vcc = 3.00 V

0.45

-40

Leak current (Tristate) V^O= Vcc or GND

µA

I^OZ

VIN = 0 V,

I/O pin input capacitance

f = 1.0 MHz

C^IN

( 69 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

5.4 External Dimensions

(1) External Dimensions of the Emulation Pod

Figure 5.6 shows external dimensions of the M3062NT3-RPD-E.

Unit: mm

Figure 5.6 External dimensions of the emulation pod

( 70 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

(2) External Dimensions of the Converter Board M30800T-PTC

Figure 5.7 shows external dimensions of the converter board M30800T-PTC (included) for a 100-

pin LCC and a sample foot pattern for 100-pin 0.65-mm-pitch (100P6S-A).

When connected to a 100-pin LCC socket

Unit: mm

*1. To use the AXS4003M295C

(Matsushita Electric Works,

Ltd.) or the IC61-1004-051

(Yamaichi Electronics Co.,

Ltd.), be sure to set up foot

patterns for the holders.

*2. To use the AXS4003M295C

(Matsushita Electric Works,

Ltd.), as the contacts of the IC

socket body touch the PC

board in the shaded area, thus

be sure to give special

consideration to the patterns

of traces so that no other pins

touch the PC board. (Through-

hole mounting is not

permitted.)

Unit: mm

Figure 5.7 External dimensions of the converter board M30800T-PTC and a sample foot pattern

( 71 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

(3) External Dimensions of the Converter Board M3T-F160-100NSD

Figure 5.8 shows external dimensions and a sample foot pattern of the converter board M3T-F160-

100NSD (not included) for a 100-pin 0.5-mm-pitch LQFP.

Unit: mm

Figure 5.8 External dimensions and a sample foot pattern of the converter board M3T-F160-100NSD

(4) External Dimensions of the Converter Board M3T-F160-100NSE

Figure 5.9 shows external dimensions and a sample foot pattern of the converter board M3T-F160-

100NSE (not included) for a 100-pin 0.4-mm-pitch TQFP.

Unit: mm

Figure 5.9 External dimensions and a sample foot pattern of the converter board M3T-F160-100NSE

( 72 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 6. Troubleshooting

This chapter describes how to troubleshoot when this product does not work properly.

6.1 Flowchart to Remedy the Troubles ............................................................................................. 74

6.2 When the Emulator Debugger Does Not Start Up Properly........................................................ 75

(1) When the LED Display of the PC4701 is Abnormal............................................................ 75

(2) Program Window is Not Displayed at Debugger Startup (Target Connected)..................... 76

(3) Program Window is Not Displayed at Debugger Startup (Target Not Connected).............. 77

6.3 How to Request for Support ........................................................................................................ 77

( 73 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 6. Troubleshooting

6.1 Flowchart to Remedy the Troubles

Figure 6.1 shows the flowchart to remedy troubles from when power to the emulator is activated until

the emulator debugger starts up. Check this while the target system is disconnected. For the latest

FAQs visit the Renesas Tools Homepage.

http://www.renesas.com/eng/products/mpumcu/toolhp/faq/m16c/m16c_e.htm

Turning on the power of PC4701

Not normal

PC4701 Front panel LEDs

1. Check emulator system connections.

See "3.7 Connecting the PC4701" (page 39).

2. Redownload the firmware.

Normal

See "4.2 Downloading Firmware" (page 56).

3. Restart the PC4701 system.

Init dialog box of emulator

debugger displayed

Not normal or error displayed

1. Check the operating environment etc. of the emulator

debugger.

Normal

See the emulator debugger user's manual.

2. Reinstall the emulator debugger.

Error displayed

See "6.2 (2) Program Window is Not Displayed at Debugger

Startup (Target Connected)" (page 76).

See "6.2 (3) Errors Occur at Debugger Startup (Target Not

Connected)" (page 77).

Program window of emulator debugger displayed

Figure 6.1 Flowchart to remedy troubles

( 74 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

6.2 When the Emulator Debugger Does Not Start Up Properly

(1) When the LED Display of the PC4701 is Abnormal

Table 6.1 LED's abnormal display and its checkpoints

Connection to

the target system

Error

Checkpoint

Check that the power cable is connected to the

PC4701.

See the PC4701 user's manual.

LEDs do not light up.

All LEDs remain lit.

Check the connection between the PC4701 and

this product.

See "3.7 Connecting the PC4701" (page 39).

The "POWER" LED of

"STATUS OF TARGET"

does not light up.

Check that power (Vcc and GND) is properly

supplied to the target system.

Connected

(1) Check that an oscillator circuit board is installed

in the emulation pod.

The "CLOCK" LED of

"STATUS OF TARGET"

does not light up.

See "3.2 Each Setting" (page 29).

(2) Check that the oscillation circuit in the emulation

pod is oscillating.

See "3.3 Selecting Clock Supply and Replacing

Oscillator Circuit Boards" (page 30).

The RESET LED of

"STATUS OF TARGET"

does not go out.

Check the reset pin of the target system is held

high.

Connected

( 75 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

(2) Program Window is Not Displayed at Debugger Startup (Target Connected)

Table 6.2 Checkpoints of errors when starting up the emulator debugger (target connected)

Error

Checkpoint

ERROR 16005:

Can't connect with the target.

(1) Check the connection between the PC4701 and host

machine.

See the PC4701 User's Manual.

(2) Check that the PC4701 is powered on.

See the PC4701 User's Manual.

(3) Check that all emulator debugger settings, interface

cable connection and switches on the rear of the

PC4701 match.

See the PC4701 User's Manual and the emulator

debugger online manual.

ERROR 16211:

(1) Download the proper firmware.

The version of PD30 and the firmware on

the target are not same.

See "4.3 Downloading Firmware" (page 56).

(2) Choose a proper MCU file in the Init dialog box.

See the emulator debugger online manual.

(3) Check that the descriptions in the MCU file are

correct.

See "2.4 (1) Making an MCU File" (page 25).

(1) Check the connection between the PC4701 and this

product.

See "3.7 Connecting the PC4701" (page 39).

(2) Check the reset pin of the target system is held high.

See the MCU specifications.

ERROR 16215:

Cannot communicate with the debugging

monitor.

(3) If the CNVss is held high at startup, check that pins

HOLD* and RDY* are held high, too.

See the MCU specifications.

(4) Check that the oscillation circuit of the emulation pod

is oscillating properly.

See "3.3 Selecting Clock Supply and Replacing

Oscillator Circuit Boards" (page 30).

(1) Check that the oscillation circuit of the target system

is oscillating properly.

See "3.3 Selecting Clock Supply and Replacing

Oscillator Circuit Boards" (page 30).

(2) Check that the PC4701 LEDs at startup show normal

operation.

ERROR 16014:

Communication ERROR.

Can't accept data.

See "4.1 (3) LED Display When the PC4701 Starts

Up Normally" (page 55).

Check that the emulator debugger has not been started

up without shutting down the PC4701.

See "IMPORTANT: Note on Quitting the Emulator

Debugger" (page 12).

ERROR 16231:

There was sent undefined data from

PC4700.

( 76 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

(3) Program Window is Not Displayed at Debugger Startup (Target Not Connected)

Table 6.3 Checkpoints of errors when starting up the emulator debugger (target not connected)

Error

Checkpoint

ERROR 16005:

Can't connect with the target.

(1) Check the connection between the PC4701 and host

machine.

See the PC4701 User's Manual.

(2) Check that the PC4701 is powered on.

See the PC4701 User's Manual.

(3) Check that all emulator debugger settings, interface

cable connection and switches on the rear of the

PC4701 match.

See the PC4701 User's Manual and the emulator

debugger online manual.

ERROR 16211:

The version of PD30 and the firmware on

the target are not same.

(1) Check the connection between the PC4701 and this

product.

See "3.7 Connecting the PC4701" (page 39).

(2) Download the proper firmware.

See "4.2 Downloading Firmware" (page 56).

(3) Choose a proper MCU file in the Init dialog box.

See the emulator debugger online manual.

(4) Check that the descriptions in the MCU file are

correct.

See "2.4 (1) Making an MCU File" (page 25).

ERROR 16215:

Cannot communicate with the debugging

monitor.

(1) Check that switch settings in the emulation pod are

correct.

See "3.4 Switch Settings" (page 34).

(2) Check that the oscillation circuit of the emulation pod

is oscillating properly.

See "3.3 Selecting Clock Supply and Replacing

Oscillator Circuit Boards" (page 30).

ERROR 16014:

Communication ERROR.

Can't accept data.

Check that the PC4701 LEDs at startup show normal

operation.

See "4.1 (3) LED Display When the PC4701 Starts Up

Normally" (page 55).

ERROR 16231:

There was sent undefined data from

PC4700.

Check that the emulator debugger has not been started

up without shutting down the PC4701.

See "IMPORTANT: Note on Quitting the Emulator

Debugger" (page 12).

6.3 How to Request for Support

Fill in the text file the installer of the emulator debugger generates in the following directory and email

to your local distributor.

\SUPPORT\product name\SUPPORT.TXT

For prompt response, please specify the following information:

(1) Operating environment

• Operating voltage:

• Operating frequency: XX.X [MHz]

• Operating mode: Single-chip, memory expansion, or microprocessor mode

(2) Problem

X.X [V]

( 77 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

MEMO

( 78 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 7. Maintenance and Guarantee

This chapter describes how to maintenance, repair provisions and how to request for repair.

7.1 Maintenance................................................................................................................................. 80

7.2 Guarantee..................................................................................................................................... 80

7.3 Repair Provisions......................................................................................................................... 80

7.4 How to Request for Repair .......................................................................................................... 81

( 79 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 7. Maintenance and Guarantee

7.1 Maintenance

If dust or dirt collects on any equipment of your emulation system, wipe it off with a dry soft cloth.

Do not use thinner or other solvents because these chemicals can cause the equipment's surface

coating to separate.

7.2 Guarantee

If your product becomes faulty within twelve months after its purchase while being used under good

conditions by observing "Precautions for Safety" described in Chapter 1 of this user's manual, we will

repair or replace your faulty product free of charge. Note, however, that if your product's fault is raised

by any one of the following causes, we will repair it or replace it with new one with extra-charge:

• Misuse, abuse, or use under extraordinary conditions

• Unauthorized repair, remodeling, maintenance, and so on

• Inadequate user's system or misuse of it

• Fires, earthquakes, and other unexpected disasters

In the above cases, contact your local distributor. If your product is being leased, consult the leasing

company or the owner.

7.3 Repair Provisions

(1) Repair with extra-charge

The products elapsed more than twelve months after purchase can be repaired with extra-charge.

(2) Replacement with extra-charge

If your product's fault falls in any of the following categories, the fault will be corrected by

replacing the entire product instead of repair, or you will be advised to purchase new one,

depending on the severity of the fault.

• Faulty or broken mechanical portions

• Flaw, separation, or rust in coated or plated portions

• Flaw or cracks in plastic portions

• Faults or breakage caused by improper use or unauthorized repair or modification

• Heavily damaged electric circuits due to overvoltage, overcurrent or shorting of power supply

• Cracks in the printed circuit board or burnt-down patterns

• Wide range of faults that makes replacement less expensive than repair

• Unlocatable or unidentified faults

(3) Expiration of the repair period

When a period of twelve months elapses after the model was dropped from production, repairing

products of the model may become impossible.

(4) Transportation fees at sending your product for repair

Please send your product to us for repair at your expense.

( 80 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

7.4 How to Request for Repair

If your product is found faulty, follow the procedure below to send your product for repair.

Customer

Distributor

Fill in the Repair Request Sheet included with this product, then send it

along with this product for repair to your local distributor. Make sure

that information in the Repair Request Sheet is written in as much detail

as possible to facilitate repair.

After checking the contents of fault, the distributor should please send

the faulty product along with the Repair Request Sheet to Renesas

Solutions Corp.

Renesas Solutions When the faulty product is repaired, it will be returned to the customer

at the earliest convenience.

CAUTION

Note on Transporting the Product:

• When sending your product for repair, use the packing box and cushion material supplied with this

product when delivered to you and specify handling caution for it to be handled as precision

equipment. If packing of your product is not complete, it may be damaged during transportation.

When you pack your product in a bag, make sure to use conductive polyvinyl supplied with this

product (usually a blue bag). When you use other bags, they may cause a trouble on your product

because of static electricity.

( 81 / 84 )

Download from Www.Somanuals.com. All Manuals Search And Download.

MEMO

Download from Www.Somanuals.com. All Manuals Search And Download.

M3062NT3-RPD-E User's Manual

Rev. 1.00

June 16, 2003

REJ10J0113-0100Z

Download from Www.Somanuals.com. All Manuals Search And Download.

Quantum Mobility Aid Access Ramp User Guide
Radio Shack Automobile Alarm TD 1500 User Guide
Radio Shack Computer Drive 26 137 User Guide
Ricoh Thermostat EK 182 40930 User Guide
RocketFish Home Theater System 09 0474 User Guide
Roper Cooktop 4347928 333240 1 User Guide
Roper Washer AL2121W User Guide
Rowenta Hair Dryer 011425 49 04 CV9020 User Guide
Samsung Microwave Oven CE2D33 CE2D33T User Guide
Sanyo Car Video System CE42LH2DPB User Guide